Wharfedale Pro | Titan 15 Passive | User manual | TITAN 15 2-way Portable, Passive Loudspeaker

TITAN
15 User’s Manual
2-WAY PROFESSIONAL
PASSIVE LOUDSPEAKER
www.wharfedalepro.com
TITAN 15_Manual RevC.indd 1
8/31/06 1:19:39 PM
U S E R ' S
M A N U A L
Titan 15 is the latest innovation from
Wharfedale Pro. A high performance passive
speaker system designed around your needs.
High output, punchy low end and extended
high frequency response that’s equally at
home with music and speech. An ultra-lightweight composite enclosure that’s designed
to be stand mounted, arrayed or even used
as a floor monitor. Compact, lightweight and
affordable, the Titan 15 still packs professional
drivers that deliver unmatched performance.
TITAN 15_Manual RevC.indd 2
8/31/06 1:19:39 PM
TITAN 15 2-way Portable, Passive Loudspeaker
Warnings & Safety Instructions
1. READ ALL INSTRUCTIONS carefully and become familiar with the features and
functions of this product before operating it.
2. RETAIN THESE INSTRUCTIONS for future reference.
3. COMPLY WITH ALL WARNINGS – All warnings and instructions for this product should
be adhered to.
4. USE WITH AMPLIFIERS – In order to avoid damage to drivers and other equipment,
it is advisable to establish and follow a routine for powering up and powering down
a sound system. With all system components connected, turn on source equipment
(mixers, signal processors, record and playback units, etc.) BEFORE powering up
amplifiers. Transient voltages from powering up source equipment can damage
speakers if amplifiers are turned on when these sources are powered up. Make sure
that amplifier volumes are set to their minimum settings and power up any system
amplifiers LAST. It is recommended that all system components be allowed to stabilize
for several seconds before any source signals are introduced or level setting
adjustments are made.
Similarly, when shutting systems down, turn all amplifiers off first, before powering
down any other system components.
5. CABLES – Do not use shielded or microphone cables for connection between
amplifiers and speakers. Use only approved speaker cables with proper connectors.
6. RIGGING – SUSPENDING – MOUNTING – Rigging, suspending and mounting of this
speaker system can expose members of the public to serious health and risks and
even death. UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE
MOUNT THIS SYSTEM UNLESS YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO
SO BY RELEVANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT
SAFETY REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT PROPERLY QUALIFIED
OR DO NOT KNOW OF PERTINENT REGULATIONS, CONSULT QUALIFIED PERSONNEL
FOR ADVICE.
7. CAUTION – These professional loudspeaker systems are capable of generating very
high sound pressure levels. Use care with placement and operation to avoid
exposure to excessive volume levels that can cause permanent hearing damage if
operated to extremes.
8. SERVICE – There are no user serviceable parts inside this product. Users should not
attempt to service this product. Warranty nullification could result if this is attempted.
TITAN 15_Manual RevC.indd 3
8/31/06 1:19:39 PM
Thank you for purchasing the Wharfedale Pro TITAN 15!
The TITAN 15 is a new addition to our Titan Series which is based on our popular TITAN
12 model. The TITAN 15 offers superior acoustical voicing and new drivers that provide
a smooth high end response and a punchy, tight low end bass response in a portable
composite enclosure.
Features:
+ Custom designed, heavy duty 15" low frequency driver
+ 2" titanium high frequency compression driver
+ 90 x 60 degree integral Elliptical Wave Guide for even high frequency dispersion
+ Built in Linkwitz-Riley crossover at 1.8kHz
+ DTF™ Dynamic Thermal Filament – Integral High-Frequency Driver
Overload protection
+ Design for a wide variety of sound reinforcement applications
+ Built in, rubberized easy-grip handles for convenient transportation
+ Integral pole mount adapter for stand mounting
+ Trapezoidal shape for vertical arrays and horizontal stage monitor use
+ Top stacking feature for easy integration of multiple enclosures
+ Ten M8 threaded rigging inserts for several hang-mount options
+ Bottom mounted M8 threaded inserts that fit the OmniMount® 60.0 footprint
+ Injection molded enclosure construction
+ Integral cord wrap and cable anchor molded into the enclosure
+ NL4 input connectors
Operation
The TITAN 15 is a passive, two-way, speaker system that provides an 8 ohm impedance
load, per enclosure, to each output channel of the system power amplifier. Multiple TITAN
15 enclosures can be “daisy-chained”, in parallel, with the impedance load dropping in
half with each additional enclosure. In other words, two TITAN 15 enclosures, connected
in parallel, will provide a 4 Ohm impedance load. Like wise, three TITAN 15 enclosures
connected in parallel will provide a 2 ohm impedance load to the amplifier. Be aware that
some amplifiers are not designed to accept loads as low as 2 ohms and loads this low can
result in decreased performance and overheating of the amplifier and can cause damage
TITAN 15_Manual RevC.indd 4
8/31/06 1:19:40 PM
to amplifier electronics. Consult the manufacturers operating manual for the amplifier
before connecting multiple speakers together.
The HIGH FREQUENCY EQ switch provides a 3dB boost to the high frequency driver for long throw
applications. Switch selections are “BOOST” (3dB increase) and “FLAT” (no increase).
Connections
The TITAN 12 PRO input connections from the output of the amplifier will be via ¼” phone jacks or
Speakon® NL4 connectors that are located on the rear mounted input plate. NL4 connector pin wiring is configured as follows:
+1 = Positive
-1 = Negative
Optional Accessories
+ Wall mount bracket – Enables surface mounting with pan and tilt positioning for
fixed installations
+ Titan Tour Bag – Ballistic nylon zippered carrying bag with storage pocket for cables.
TITAN 15_Manual RevC.indd 5
8/31/06 1:19:40 PM
TITAN 15 Specifications
Loudspeaker Type:
Frequency Response +/—3dB:
Sensitivity 1W@1M:
High Frequency Coverage (H x V):
Peak SPL:
System Impedance:
15" 2-way
50—18KHz
97dB
90˚ x 60˚
129dB
8 ohm
POWER HANDLING CAPABILITY (watts)
Continuous:
Music:
Peak:
400W
800W
1600W
LOW FREQUENCY DRIVER
Size (mm / inches):
Coil Size (mm / inches):
381mm / 15"
75mm / 3"
HIGH FREQUENCY DRIVER
Type:
Coil Size (mm / Inches):
Exit Size (mm / inches):
Diaphragm Material:
High Frequency Driver Protection:
Compression Driver
51mm / 2"
25mm / 1"
Titanium
DTF™- Dynamic Thermal Filament (2 x SK3 Bulb)
HIGH FREQUENCY HORN
Type:
Throat Size (inches):
EWG™-Elliptical Wave Guide
25mm / 1"
CROSSOVER
Type:
Frequency / Filter:
2-way
1.8kHz/12dB per oct.
ENCLOSURE
Shape: Trapezoidal for vertical array and horizontal stage
monitor applications
Material: Molded polypropylene
Rigging / Bracket Options: + (10) M8 threaded rigging points for safe flown applications
+ (4) M8 threaded inserts on bottom in Omnimount 60.0-type footprint
+ Pole-mount receptacle with lock screw
+ Optional wall-mount bracket
CONNECTIONS
Rear Panel Input Connectors:
Net Weight (kg / lbs..):
Gross Weight (kg / lbs.):
Dimensions (H x W x D):
(2) NL4 connectors (parallel)
22kg / 48.4 lbs.
25kg / 55 lbs.
708.3 x 477.8 x 401.77mm / 27.9" x 18.8" x 15.8"
*Features, details and specifications subject to change without notice
TITAN 15_Manual RevC.indd 6
8/31/06 1:19:40 PM
THE WHARFEDALE PRO ADVANTAGE
While other companies increasingly outsource manufacturing, we continue to add
to our factory; already at 1.5 million square
feet in size. That’s because at Wharfedale
Pro we design, engineer, tool and manufacture each and every component that goes into
our speaker systems. All of which helps explain how we can pack so much technology,
performance and quality into our products
at an incredibly low cost. Recognized since
1932 as a pioneering brand, Wharfedale Pro
is now part of the International Audio Group
with operations and distributionworldwide.
Our mission remains to design and build
the very best Pro Audio gear possible, with
great technologies, abundant features and
unmatched quality at the very lowest possible
cost. That’s the Wharfedale Pro advantage!
TITAN 15_Manual RevC.indd 7
8/31/06 1:19:40 PM
UNPACKING
All Wharfedale Pro products are fully checked before leaving the factory.
After unpacking please inspect cabinets for any physical damage. Please
retain the shipping carton if possible and internal packing material in
case the unit needs to be returned. Please check as soon as possible that
the unit is functioning. In the event of any damage, please contact your
dealer immediately.
WHARFEDALE PRO LIMITED WARRANTY *
Wharfedale Titan loudspeaker systems are warranted to be clear of manufacturing or materials defects for a period of one year from the original
date of purchase. In the event of malfunction, contact your authorized
Wharfedale Professional dealer or distributor for information.
* Be aware that warranty details may differ from country to country.
Contact your dealer or distributor for information. These terms do not
infringe your statutory rights.
* Details and specifications subject to change without notice.
© 2006 Wharfedale Pro is a member of the International Audio Group .
IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambridgeshire, PE29 6XU
WHARFEDALE PRO [USA]
ph: +1.877.440.0888
ph: +1.425.861.3909
fx: +1.425.861.3906
WHARFEDALE PRO [UK]
ph: +44 (0) 845 4580011
ph: +44 (0) 1480 447700
fx: +44 (0) 1480 431767
WHARFEDALE PRO [GERMANY]
ph: +49 (0) 2161-61783-0
fx: +49 (0) 2161-6178350
WHARFEDALE PRO [INT.]
ph: +86 (0) 755 8209 6639
fx: +86 (0) 755 8209 0203
www.wharfedalepro.com
TITAN 15_Manual RevC.indd 8
8/31/06 1:19:40 PM