Sharp MX-3114N Operation Specifications

DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
MX-2314N/MX-2614N/MX-3114N
START GUIDE
CONTENTS
CAUTIONS ___________________________________________ 3
PART NAMES ________________________________________ 7
TURNING THE POWER ON AND OFF _____________________ 8
OPERATION MANUALS AND HOW TO USE THEM ��������� 9
SPECIFICATIONS ____________________________________ 10
INFORMATION ON DISPOSAL __________________________ 13
TO THE ADMINISTRATOR OF THE MACHINE _____________ 14
TRADEMARK ACKNOWLEDGMENTS ___________________ 15
Keep this manual close at hand for reference whenever needed.
Caution!
For the users of the fax function
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
� FAX interface cable and Line cable:
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
These special accessories must be used with the device.
The declaration of conformity may be consulted at: http://www.sharp.de/doc/MX-FX11.pdf
The equipment should be installed near an accessible socket outlet for easy disconnection.
SOFTWARE LICENCE
Each instruction also covers the optional units used with these products.
Notice for users in the UK
The SOFTWARE LICENCE will appear when you install the software from the CD-ROM. By using all
or any portion of the software on the CD-ROM or in the machine, you are agreeing to be bound by
the terms of the SOFTWARE LICENCE.
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse
to BS1362 marked
or
and of the same rating as the one removed from the plug must be
used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied
either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable
plug is fitted and fit an appropriate type observing the wiring code below.
• The explanations in this manual assume that you have a working knowledge of your
Windows or Macintosh computer.
• For information on your operating system, please refer to your operating system
manual or the online Help function.
• The explanations of screens and procedures in this manual are primarily for Windows
7 in Windows® environments. The screens may vary depending on the version of the
operating system.
• This manual contains references to the fax function. However, please note that the
fax function is not available in some countries and regions.
• This manual contains explanations of the PC-Fax driver and PPD driver. However, please
note that the PC-Fax driver and PPD driver are not available and do not appear on the
software for installation in some countries and regions.
In this case, please install the English version if you want to use these drivers.
• Considerable care has been taken in preparing this manual. If you have any
comments or concerns about the manual, please contact your dealer or nearest
authorised service representative.
• This product has undergone strict quality control and inspection procedures. In
the unlikely event that a defect or other problem is discovered, please contact your
dealer or nearest authorised service representative.
• Aside from instances provided for by law, SHARP is not responsible for failures
occurring during the use of the product or its options, or failures due to incorrect
operation of the product and its options, or other failures, or for any damage that
occurs due to use of the product.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately
and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted
elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW:
Earth
BLUE:
Neutral
BROWN:
Live
As the colours of the wires in this mains lead may not correspond with coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the
plug which is marked with the letter E, or by the safety earth symbol
, or coloured green or
greenand-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked
with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured red.
Products that have earned the ENERGY STAR® are designed to protect the
environment through superior energy efficiency.
The products that meet the ENERGY STAR® guidelines carry the logo shown above.
The products without the logo may not meet the ENERGY STAR® guidelines.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
�Warranty
While every effort has been made to make this document as accurate and helpful as possible,
SHARP Corporation makes no warranty of any kind with regard to its content. All information
included herein is subject to change without notice. SHARP is not responsible for any loss or
damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2012. All rights reserved. Reproduction, adaptation or translation
without prior written permission is prohibited, except as allowed under copyright laws.
EMC (this machine and peripheral devices)
�Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Peripheral devices are described in the [PERIPHERAL DEVICE] in the Operation Guide.
This machine contains the software having modules developed by Independent JPEG Group.
This product includes Adobe® Flash® technology of Adobe Systems Incorporated.
MATERIAL SAFETY DATA SHEET
The MSDS (Material Safety Data Sheet) can be viewed at the following URL address: http://www.
sharp-world.com/corporate/info/index.html.
Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved.
2
CAUTIONS
Symbols in this manual
To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols
are classified as explained below. Be sure you understand the meaning of the symbols when
reading the manual.
WARNING
Indicates a risk of death or serious injury.
Meaning of the symbols
CAUTION!
HOT
PINCH POINT
KEEP CLEAR
PROHIBITED
ACTIONS
DO NOT
DISASSEMBLE
CAUTION
Indicates a risk of human injury or property
damage.
MANDATORY
ACTIONS
Power notes
WARNING
CAUTION
Be sure to connect the power cord only to a power outlet that meets the specified
voltage and current requirements. Also make certain the outlet is properly
grounded. Do not use an extension cord or adapter to connect other devices to
the power outlet used by the machine.
Using an improper power supply may cause fire or electrical shock.
When removing the power plug from the outlet, do not pull on the cord.
Pulling on the cord may cause damage such as wire exposure and breakage, and may result in fire or
electrical shock.
If you will not use the machine for a long time, be sure to remove the power plug
from the outlet for safety.
* For the power supply requirements, see the name plate in the lower left corner of the left side of the
machine.
Do not damage or modify the power cord.
When moving the machine, switch off the main power and remove the power plug
from the outlet before moving.
Placing heavy objects on the power cord, pulling it, or forcibly bending it
will damage the cord, resulting in fire or electrical shock.
The cord may be damaged, creating a risk of fire or electrical shock.
Do not insert or remove the power plug with wet hands.
This may cause electrical shock.
3
Installation notes
Do not install the machine in a location with poor air
circulation.
A small amount of ozone is created inside the machine during
printing. The amount of ozone created is not sufficient to be
harmful; however, an unpleasant odor may be noticed during large
copy runs, and thus the machine should be installed in a room with
a ventilation fan or windows that provide sufficient air circulation.
(The odor may occasionally cause headaches.)
* Install the machine so that people are not directly exposed to
exhaust from the machine. If installed near a window, ensure that
the machine is not exposed to direct sunlight.
CAUTION
Do not install the machine on an unstable or slanted surface. Install the machine
on a surface that can withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
If peripheral devices are to be installed, do not install on an uneven floor, slanted surface, or otherwise
unstable surface. Danger of slippage, falling, and toppling. Install the product on a flat, stable surface
that can withstand the weight of the product.
Near a wall
Be sure to allow the required space around the machine for
servicing and proper ventilation. (The machine should be no closer
than the distances indicated below from walls. The indicated
distances are for the case when a saddle finisher and large
capacity paper tray are not installed.)
Do not install in a location with moisture or dust.
Risk of fire and electrical shock.
If dust enters the machine, dirty output and machine failure may result.
30 cm
45 cm
Locations subject to vibration.
Locations that are excessively hot, cold,
humid, or dry (near heaters, humidifiers, air
conditioners, etc.)
Vibration may cause failure.
The paper will become damp and condensation may form
inside the machine, causing misfeeds and dirty output.
SPECIFICATIONS (page 10)
If the location has an ultrasonic humidifier, use pure water for
humidifiers in the humidifier. If tap water is used, minerals and
other impurities will be emitted, causing impurities to collect
on the inside of the machine and create dirty output.
CAUTION
The machine includes a built-in hard drive. Do not subject the machine to shock or
vibration. In particular, never move the machine while the power is on.
When the machine is installed, the adjusters (4) must be
lowered to the floor to secure the machine (prevent it from
moving).
• The machine should be installed near an accessible power outlet for easy connection.
• Connect the machine to a power outlet which is not used for other electric appliances. If a lighting
fixture is connected to the same outlet, the light may flicker.
Rotate the adjusters in the locking direction until they are in firm contact with the floor.
If you find it necessary to reposition the machine due to rearrangement
of your office layout or other reason, retract the adjusters from the floor,
turn off the power, and then move the machine.
30 cm
Lock
Release
About consumables
(After moving the machine, lower the adjusters again to secure the machine.)
Locations exposed to direct sunlight
CAUTION
Plastic parts may become deformed and dirty output may result.
Do not throw a toner cartridge into a fire.
Locations with ammonia gas
Toner may fly and cause burns.
Installing the machine next to a diazo copy machine may cause dirty output.
Store a toner cartridge out of the reach of children.
4
Handling precautions
WARNING
CAUTION
Do not place a container of water or other liquid, or a
metal object that might fall inside, on the machine.
Do not look directly at the light source.
Doing so may damage your eyes.
If the liquid spills or the object falls into the machine, fire or electrical
shock may result.
Do not remove the machine casing.
Do not block the ventilation ports on the machine. Do not install the machine in a
location that will block the ventilation ports.
High-voltage parts inside the machine may cause electrical shock.
Blocking the ventilation ports will cause heat to build up in the machine, creating a risk of fire.
Do not make any modifications to this machine.
The fusing unit and paper exit area are hot. When
removing a misfeed, do not touch the fusing unit and
paper exit area. Take care not to burn yourself.
Doing so may result in personal injury or damage to the machine.
Do not use a flammable spray to clean the machine.
If gas from the spray comes in contact with hot electrical components or the fusing unit inside
the machine, fire or electrical shock may result.
When loading paper, removing a
misfeed, performing maintenance,
closing the front and side covers, and
inserting and removing trays, take care
that your fingers are not pinched.
If you notice smoke, a strange odor, or other abnormality,
do not use the machine.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove the power plug from
the power outlet.
Contact your dealer or nearest authorised service representative.
The machine includes the document filing function, which stores document image data on the
machine’s hard drive. Stored documents can be called up and printed or transmitted as needed.
If a hard drive failure occurs, it will no longer be possible to call up the stored document data.
To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the
originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for
any damages or loss due to the loss of stored document data.
If a thunder storm begins, switch off the main power and remove the power plug
from the outlet to prevent electrical shock and fire due to lightning.
Laser information
If a piece of metal or water enters the machine, switch off the main power and
remove the power plug from the power outlet.
Contact your dealer or nearest authorised service representative. Using the machine in this condition
may result in electrical shock or fire.
Wave length
790 nm ± 10 nm
Pulse times
Normal paper mode (P/S = 104 mm/s) = (5.15 µs ± 0.03 ns) / 7 mm
Heavy paper mode (P/S = 70 mm/s) = (3.83 µs ± 0.03 ns) / 7 mm
Output power
Max 0.405 mW
�Caution
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007)
5
Acoustic noise emission (measurement according to ISO7779)
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges,
and staple cartridges for the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge,
and transparency film.
GENUINE SUPPLIES
Noise emission values
Sound power level LWAd
Operating (continuous printing)
For best copying results, be sure to use only Sharp Genuine Supplies which
are designed, engineered, and tested to maximize the life and performance
of Sharp products. Look for the Genuine Supplies label on the toner
package.
Standby mode (Low power level mode)
MX-2314N
MX-2614N
MX-3114N
7.2 B
7.12 B
7.22 B
-
-
-
MX-2314N
MX-2614N
MX-3114N
55 dB
54 dB
55 dB
17 dB
-
-
Sound pressure level LpAm
Storage of supplies
Operating
(continuous printing)
Bystander positions
Standby mode
Bystander positions
•Operating: w
ith option MX-DE14 and MX-FN17. (MX-2314N)
with option MX-DE14. (MX-2614N/MX-3114N)
•Standby: “-”=less than background noise.
� Proper storage
1. Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3.Paper stored in packages standing up or out of the wrapper may curl or become damp,
resulting in paper misfeeds.
� Storing toner cartridges
Store a new toner cartridge box horizontally with the top side up. Do not store a toner cartridge
standing on end. If stored standing on end, the toner may not distribute well even after shaking the
cartridge vigorously, and will remain inside the cartridge without flowing out.
� Staple cartridge
The finisher require the following staple cartridge:
MX-SCX1 (for finisher)
Approx. 5000 per cartridge x 3 cartridges
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the
termination of production. Spare parts are those parts of the machine which may break down within
the scope of the ordinary use of the product, whereas those parts which normally exceed the life
of the product are not to be considered as spare parts. Consumables too, are available for 7 years
following the termination of production.
6
PART NAMES
Operation panel
Automatic document feeder
PRINT mode indicators (
•READY indicator
)
Print jobs can be received when this indicator is lit.
USB connector (A type)
Keyboard*
•DATA indicator
Exit tray unit (right tray)*
This blinks while print data is being received and lights steadily
while printing is taking place.
Touch panel
[JOB STATUS] key (
)
[POWER] key (
)
Output tray
(Centre tray)
IMAGE SEND mode indicators (
•LINE indicator
Front cover
[SYSTEM SETTINGS] key (
)
This lights up during transmission or
reception of a fax or Internet fax. This also
lights during transmission of an image in
scan mode.
•DATA indicator
[HOME] key (
Bypass tray
Tray 1
Main power
switch
Tray 2 (when paper feed tray is installed)*
Tray 3 (when paper feed tray is installed)*
Tray 4 (when paper feed tray is installed)*
* Peripheral device.
7
)
)
This blinks when a received fax or Internet
fax cannot be printed because of a
problem such as out of paper.
This lights up when there is a transmission
job that has not been sent.
TURNING THE POWER ON AND OFF
This machine has two power switches. The main power switch is at the bottom left after the front cover is opened. The other power switch is the [POWER] key (
) on the operation panel.
Turning on the power
(1) Switch the main power switch to the “
(2) Press the [POWER] key (
” position.
) to turn on the power.
Turning off the power
(1) Press the [POWER] key (
) to turn off the power.
(2) Switch the main power switch to the “
” position.
Main power
switch
• If the main power indicator is blinking, press the [POWER] key ( ) after it becomes steadily lit.
• When turning off the power, make sure that the indicator lights on the operation panel turn off as well.
• In the event of a power failure or other reason that causes the machine to suddenly turn off, turn back on the power of
the machine and then proceed to turn off the machine following the correct procedures.
Switching off the main power switch or removing the power cord from the outlet while any of the indicators are lit or
blinking may damage the hard drive and cause data to be lost.
• Switch off both the [POWER] key ( ) and the main power switch and unplug the power cord if you suspect a machine
failure, if there is a bad thunderstorm nearby, or when you are moving the machine.
Main power
indicator
[POWER] key
When the main power
switch is switched on, the
main power indicator on the
operation panel lights up.
When using the fax or Internet fax function, always keep the main power switch in the “on” position.
� Restarting the machine
In order for some settings to take effect, the machine must be restarted.
If a message in the touch panel prompts you to restart the machine, press the [POWER] key (
In some states of the machine, pressing the [POWER] key (
) to turn off the power and then press the key again to turn the power back on.
) to restart will not make the settings take effect. In this case, use the main power switch to switch the power off and then on.
8
OPERATION MANUALS AND HOW TO USE THEM
Operation manuals
How to read the Operation Guide
The instructions for this manual are separated in the following three sections.
The [Operation Guide] can be downloaded from the machine and viewed on a computer. You can
download the [Operation Guide] following the procedures below while the machine is connected to
the network.
Before using the machine
Start Guide: this manual
This section explains precautions to ensure safe usage, part names
and how to switch on/off the power. This section also includes
important information for persons that are responsible for the
maintenance of this machine.
Read this section before using the machine for the first time.
1 Confirm the machine’s IP address
First, touch the [SYSTEM SETTINGS] key ( ) on the operation panel and then touch [List
Print (User)] when it appears on the touch panel.
Next, select [NIC Page] from [Printer Test Page] and then touch the [Print] button. Confirm the
machine’s IP address from the printed list.
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
MX-2314N/MX-2614N/MX-3114N
START GUIDE
CONTENTS
CAUTIONS __________________________________________ 3
PART NAMES _______________________________________ 7
TURNING THE POWER ON AND OFF ____________________ 8
OPERATION MANUALS AND HOW TO USE THEM _________ 9
SPECIFICATIONS ___________________________________ 10
2 Insert the machine’s IP address into the address bar
INFORMATION ON DISPOSAL _________________________ 13
TO THE ADMINISTRATOR OF THE MACHINE ____________ 14
TRADEMARK ACKNOWLEDGMENTS __________________ 15
of your web browser to access the machine
http://machine’s IP address/
User verification may be required depending on the machine’s settings.
Please check with the machine’s administrator to obtain the account information necessary for
verification.
Keep this manual close at hand for reference whenever needed.
Printing and faxing from a computer
Software Setup Guide (PDF)
This section explains how to install the various drivers needed
when using this machine as a printer, network scanner, or fax
machine.
Read this section when using this machine from a computer. The
Software Setup Guide is on the “Software CD-ROM”.
3 Download the [Operation Guide]
DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM
Click [Operation Manual Download] from the page displayed. Next, select a language to
download the file in from the [Language] list and then click on the [Download] button.
Software Setup Guide
4 Double-click on the downloaded file to display the Operation Guide
BEFORE INSTALLING
THE SOFTWARE
SETUP IN A WINDOWS
ENVIRONMENT
SETUP IN A MACINTOSH
ENVIRONMENT
TROUBLESHOOTING
HOW TO USE THE OPERATION GUIDE (on the accessory CD-ROM)
The Operation Guide on the accessory CD-ROM provides detailed instructions for operating the
machine. The Operation Guide is provided in PDF format.
Insert the supplied CD-ROM into your CD-ROM drive. CD-ROM will run automatically.
If it does not start automatically, double-click the CD-ROM icon or display the contents of the
CD-ROM and double-click “index.html”.
Directions for use
Operation Guide (PDF)
Information on the copier, fax, and other various functions that
this machine provides have been compiled into a PDF file called
[Operation Guide].
Read the Operation Guide to learn how to use this machine, when
you want to know more about its functions, or when you have trouble
operating it.
MX-2314N: The [Operation Guide] is on the “manual CD-ROM”.
MX-2614N/MX-3114N: The [Operation Guide] is downloaded from this machine itself.
To view the manual in PDF format, Acrobat Reader or Adobe Reader of Adobe Systems Incorporated
is required. If neither program is installed on your computer, the programs can be downloaded from
the following URL: http://www.adobe.com/
9
Note:
• If you will be viewing the Operation Guide repeatedly, you may fi nd it convenient to copy the
Operation Guide fi le to your computer.
• The Operation Guide can be printed out using Acrobat Reader. SHARP recommends printing out
the sections which you refer to regularly.
• Refer to “Help” of Acrobat Reader for more details on how to use Acrobat Reader.
SPECIFICATIONS
Basic Specifications / Copier specifications
Name
MX-2314N/MX-2614N/MX-3114N
Type
Desktop
Colour
Full colour
Copier system
Laser electrostatic copier
Same size: 1:1 ± 0.8 % Enlarge: 115 %, 122 %, 141 %, 200 %, 400 %
Copy rations
Paper feed / capacity
Max. paper feed / max. capacity
Continuous copy
Scan (full colour): 600 × 600 dpi
Gradation
Scan: equivalent to 256 levels / Print: equivalent to 256 levels
Original paper sizes
Max. A3 (11"×17") / sheets, bound documents
Storage
paper, Envelopes
Ambient environment
Tray 1-4: A3, B4, A4, A4R, B5, B5R, A5R, 11" × 17", 8-1/2" × 14",
8-1/2" × 11"R, 7-1/4 × 10-1/2"R, 5-1/2" × 8-1/2"R
Required power supply
Multi-bypass tray: A3 wide (12" × 18") to A5R, 5-1/2" × 8-1/2"R,
Lost margin: (trailing edge): 2 mm (6/64") - 5 mm (- 13/64")
Dimensions
Leading edge / trailing edge: total 8 mm (21/64") or lessNear edge /
Weight
First-copy time
Full colour: 10 seconds
8.1 seconds
7.9 seconds
B/W:
5.9 seconds
5.8 seconds
Overall dimensions
name plate in the lower corner of the left side of the machine.)
Power consumption Max. 1.84 kW (220-240 V) / 1.44 kW (100-127 V)
(22-61/64" (W) × 25-9/32" (D) × 28-3/16" (H))
MX-2614N/MX-3114N: 6
08 mm (W) × 642 mm (D) × 834 mm (H)
MX-2314N: 72.6 kg (161 lbs.)
MX-2614N/MX-3114N: 76.2 kg (168 lbs.)
MX-2614N/MX-3114N: 8
75.5 mm (W) × 642 mm (D)
(With multi-bypass tray extended)
 Portrait feeding of A4 (8-1/2" x 11") sheets.
(when shifter is not in operation)
10 °C (54 °F) to 30 °C (86 °F) (85 % RH)
(34-15/32" (W) × 25-9/32" (D))
 This may vary depending on the state of the machine.
Continuous copying speeds*
10 °C (54 °F) to 35 °C (91 °F) (20 % to 60 % RH)
(With multi-bypass tray extended)
MX-2314N MX-2614NMX-3114N
7.4 seconds
Actual format capacity is less.
MX-2314N: 8
50 mm (W) × 642 mm (D) (33-15/32" (W) × 25-9/32" (D))
 This may vary depending on the ambient conditions.
 1 GB = One billion bytes when referring to hard drive capacity.
(23-15/16" (W) × 25-9/32" (D) × 28-3/16" (H))
far edge: total 4 mm (11/64") ± 2 mm (± 6/64") or less
18 seconds
Max. 999 copies
MX-2314N: 5
83 mm (W) × 642 mm (D) × 834 mm (H)
Lost margin (leading edge): 4 mm (11/64") ± 1 mm (± 3/64")
MX-3114N
 Using 80 g/m2 (21 lbs.) weight paper
(including options such as the desk)
Transparency film, Heavy paper, Envelopes
MX-2314NMX-2614N
3,100 sheets in 4 trays plus 100-sheet multi-bypass tray
Local voltage ± 10 % (For the power supply requirements, see the
8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11",
19 seconds 18 seconds
U
sing 80 g/m2 (21 lbs.) weight paper
* On the MX-2314N, the productivity kit is required.
A3 wide (12" × 18") to A5R, 5-1/2" × 8-1/2"R, Transparency film, Heavy
Warm-up time
500 sheets in one tray plus 100-sheet multi-bypass tray
HDD: 320 GB*
Print: 600 × 600 dpi, equivalent to 9,600 dpi × 600 dpi
Copy sizes
Reduce: 25 %, 50 %, 70 %, 81 %, 86 %
Zoom range: 25 to 400 % (25 - 200 % using RSPF) in 1 % increments,
total 376 increments.
Scan (B/W): 600 × 600 dpi, 600 × 400 dpi, 600 × 300 dpi
Scanning resolution
MX-2314N MX-2614NMX-3114N
A4, B5, 8-1/2" × 11"
23 copies/min. 26 copies/min. 31 copies/min.
A4R, 8-1/2" × 11"R,
15 copies/min. 19 copies/min. 20 copies/min.
B5R, 7-1/4" × 10-1/2"R
B4, 8-1/2" × 14"
13 copies/min. 16 copies/min. 17 copies/min.
A3, 11" × 17"
11 copies/min. 14 copies/min. 15 copies/min.
* Continuous speed for same original source. Output may be
temporarily interrupted to stabilize image quality.
10
Automatic document feeder
Name
Reversing Single Pass Feeder (RSPF)
Document feeder types
Reversing Single Pass Feeder (RSPF)
Original paper sizes
A3 (11" × 17") to A5 (5-1/2" × 8-1/2")
Original paper types
Paper weightThin paper 35 g/m2 (9 lbs. bond) to 49 g/m2 (13 lbs. bond)
Plain paper 50 g/m2 (13 lbs. bond) to 128 g/m2 (32 lbs. bond)
Two-sided
50 g/m2 (13 lbs. bond) to 105 g/m2 (28 lbs. bond)
Paper storage capacity
100 sheets (80 g/m (21 lbs.)) (or maximum stack height of 13 mm
(33/64"))
Scan speed (copy)
B/W: 50 one-sided sheets/minute
(A4 (8-1/2" × 11") horizontal) (600 × 400 dpi)
Colour: 36 one-sided sheets/minute
(A4 (8-1/2" × 11") horizontal) (600 × 600 dpi)
Max. number of stapled sheets
(90g/m2 (24lbs.))
Max. number of 50 sheets (A4 (8-1/2" × 11"), A4R (8-1/2" × 11"R), B5)
Max. number of 30 sheets (A3 (11" × 17"), B4 (8-1/2" × 14"))
Staple position
3 locations (front, rear or both)
Required power supply
Supplied from this machine
Weight
Approx. 12 kg (26 lbs.)
Dimensions
When output paper tray is stored
428 mm (W) × 593 mm (D) × 198mm (H)
(16-55/64" (W) × 23-22/64" (D) × 7-51/64" (H))
When output paper tray is extended
612 mm (W) × 593 mm (D) × 198 mm (H)
(24-6/64" (W) × 23-22/64" (D) × 7-51/64" (H))
2
Punch module
Drawer
Name
(MX-DE12)
Paper sizes
A3 (11" × 17") to A5R (5-1/2" × 8-1/2"R)
Useable paper
60 g/m2 (16 lbs. bond) to 209 g/m2 (110 lbs. index)
(MX-DE13)
Name
Punch module (MX-PN11A, MX-PN11B, MX-PN11C, MX-PN11D) for
finisher
Paper size for punch module
A3 (11" × 17") to B5R (7-1/4" × 10-1/2"R)
 Cannot punch special types of paper such as OHP.
Holes
MX-PN11A
MX-PN11B
MX-PN11C
MX-PN11D
(MX-DE14)
2 holes
3 holes
4 holes
4 holes (wide)
Paper capacity
500 sheets
Dimensions
583 mm (W) × 577 mm (D) × 382 mm (H)
(22-61/64" (W) × 22-46/64" (D) × 15-1/64" (H))
Required power supply
Supplied from finisher
Weight
Approx. 3 kg (7 lbs.)
Weight
MX-DE12: Approx. 21 kg (46 lbs.)
MX-DE13: Approx. 23 kg (51 lbs.)
MX-DE14: Approx. 28 kg (61 lbs.)
Dimensions
98 mm (W) × 477 mm (D) × 137 mm (H)
(3-55/64" (W) × 18-50/64" (D) × 5-26/64" (H))
1,000 (500 × 2)
1,500 (500 × 3)
Fax Specifications
Finisher
Name
Finisher (MX-FN17)
Paper sizes
Depends on feeder specifications
Useable paper
55 g/m2 (13 lbs. bond) to 300 g/m2 (110lbs. cover)
Number of trays
1 Tray
Tray capacity (80g/m2 (21 lbs.))
Non-stapledA3 wide (12" × 18") / A3 (11" × 17") /
B4 (8-1/2" × 14"): 250 sheets
A4 (8-1/2" × 11") / A4R (8-1/2" × 11"R) /
B5 / B5R (7-1/4” × 10-1/2”R) / A5R (5-1/2” ×
8-1/2”R): 500 sheets
Staple functionA3 (11" × 17") / B4 (8-1/2" × 14"): 30 units or 250
sheets
A4 (8-1/2" × 11") /A4R (8-1/2" × 11"R) /
B5: 30 units or 500 sheets
Name
Facsimile expansion kit (MX-FX11)
Useable lines
General phone lines (PSTN), automated branch exchange (PBX)
Scanning line density
Normal characters:
8 dot/mm × 3.85 line/mm
Small characters:
8 dot/mm × 7.7 line/mm
Fine characters:
8 dot/mm × 15.4 line/mm
High-definition:
16 dot/mm × 15.4 line/mm
Connection speed
Super G3: 33.6 kbps, G3: 14.4 kbps
Coding method
MH, MR, MMR, JBIG
Connection mode
Super G3 / G3
A3 (11" × 17") to A5 (5-1/2" × 8-1/2") (Paper with a max. length of
Original paper sizes for transmission
1,000 mm* can be transmitted (one-sided and B/W only).)
* Internet fax (optional) is up to 800 mm (at 600 x 600 dpi).
11
Registered paper size
A3 (11" × 17") to A5 (5-1/2" × 8-1/2")
Transmission time
Approx. 2 seconds * (A4 (8-1/2" × 11") Sharp standard paper, normal
characters, Super G3 (JBIG))
Memory
1GB (512 MB standard for the MX-2314N)
Notes
Touch dial memoryMax. 1,000 entries (Including group dialling
for fax, scanner, and Internet fax)
Group dialMax. of 500 entries
Mass transmissionsMax. of 500 recipients
Network Scanner Specifications
Type
Colour scanner
100 × 100 dpi, 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi
Scan resolution (main × vertical)
600 × 600 dpi (push scan)
50 to 9,600 dpi *1 (pull scan)
Scan speed
* Complies with the 33.6 kbps transmission method for Super G3 facsimiles standardized by the International
(A4 (8-1/2" × 11") horizontal)
Telecommunications Union (ITU-T). This is the speed for when sending an A4 (8-1/2" × 11") size piece of
paper of around 700 characters at standard image quality (8 × 3.85 line/mm) in Hi-speed mode (33.6 kbps).
B/W
50 sheets/minute (one-sided)
Colour
50 sheets/minute (one-sided)
 When in standard mode using Sharp standard paper (A4 (8-1/2" ×
11") size with 6% coverage) and the auto colour detector is turned
off. The speed varies depending on the data volume of the original.
This is the transmission speed for image information only and does not include time for transmission control.
The actual time needed for a transmission depends on the content of the text, type of receiving fax machine,
Interface
and telephone line conditions.
Compatible protocols
10BASE-T/100BASE-TX/1000BASE-T,
USB 2.0 (during USB memory scanning)
TCP/IP (IPv4)
Pull scan (TWAIN) *3Windows XP, Windows Server 2003, Windows
Network Printer Specifications
Compatible OS *2
Vista, Windows Server 2008, Windows 7,
Windows 8, Windows Server 2012
(B/W)
Type
Built-in type
Continuous print speed
Same as continuous copy speed
Resolution
TIFF, PDF, PDF/A, encrypted PDF, XPS *4
Output format
Data processing: 600 × 600 dpi,
Print: 600 × 600 dpi, equivalent to 9600 x 600 dpi
Compression method: JPEG (high, mid, and low compression)
(MX-2314N)
Driver
PCL6 emulation (MX-2614N/MX-3114N)
Options: PS3 emulation*
Compatible protocols
*2:There are cases when a connection cannot be established. Please contact your local dealer for more
information.
2008, Windows 7, Windows 8, Windows Server 2012
*3:On the MX-2314N, the productivity kit is required.
Macintosh (Mac OS X 10.4, 10.5, 10.6, 10.7, 10.8)*
Internal fonts (options)
80 fonts for PCL, 136 fonts for PS3 emulation
Memory
Machine system memory and hard disk.
Interface
10BASE-T/100BASE-TX/1000BASE-T, USB 2.0 (high speed mode)
TWAIN compliant
*1:You must decrease the scan size when increasing the resolution.
TCP/IP, IPv4/IPv6, IPX/SPX, IPP, EtherTalk*
Windows XP, Windows Server 2003, Windows Vista, Windows Server
Compatible OS
(Grey scale/colour)
TIFF, JPEG, PDF, PDF/A, encrypted PDF, XPS *4
Standard: Sharp Advanced Printing Language-c, PCL6 emulation
Page description language
Compression method: decompression, G3 (MH), G4 (MMR)
*4:XPS is an abbreviation for the XML Paper Specification.
* When equipped with a PS3 expansion kit (MX-PK11).
12
INFORMATION ON DISPOSAL
Information on Disposal for Users (private households)
� In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in
accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. Following the implementation by member
states, private households within the EU states may return their used electrical and electronic equipment to designated collection facilities free of charge*. In some
countries* your local retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details. If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand according
to local requirements. By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative
effects on the environment and human health which could otherwise arise due to inappropriate waste handling.
� In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic
equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch
or www.sens.ch.
Attention: Your product is marked
with this symbol. It means that
used electrical and electronic
products should not be mixed with
general household waste. There
is a separate collection system for
these products.
Information on Disposal for Business Users
� In the European Union
If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising
from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the established collection system or your local authority for
take-back of your used products.
� In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
13
TO THE ADMINISTRATOR OF THE MACHINE
or Scan to Desktop destination).
System settings password
This function can be used by the administrator of the machine to archive all transmitted and
received data.
A password is necessary to change the machine’s system settings using administrator authority.
To configure the document administration settings, click [Application Settings] and then [Document
System settings can be changed from either the operation panel or using a computer web browser.
Administration Function] in the Web page menu. (Administrator rights are required.)
After setting up the machine, refer to [SYSTEM SETTINGS] in the Operation Guide to set a new
password.
• The format, exposure, and resolution settings of transmitted and received data
remain in effect when the data is forwarded.
• When forwarding is enabled for data sent in fax mode,
• The [Direct TX] key does not appear in the touch panel.
• Quick online transmission and dialling using the speaker cannot be used.
The administrator password is interfaced between the operation panel and the website, so
passwords changed on the operation panel will be effective when logging in on the website.
Password for logging in from this machine
For the users of the fax function
The factory default password for the machine is “admin”.
Important safety instructions
Password for logging in from a computer
• If any of your telephone equipment is not operating properly, you should immediately remove it
There are two accounts that can log in from a web browser: “Administrator” and “User”. The factory
from your telephone line, as it may cause harm to the telephone network.
default passwords for each account are shown on the right side. Signing in as an “Administrator”
• Never install telephone wiring during a lightning storm.
will allow you to manage all the settings available via web browser.
Account
Password
User
users
users
Administrator
admin
admin
• Never install telephone socket in wet locations unless the socket is specifically designed for wet
locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
Please take care not to forget newly set administrator passwords.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
Forwarding all transmitted and received data to the
administrator (document administration function)
• Do not install or use the machine near water, or when you are wet. Take care not to spill any
liquids on the machine.
• Save these instructions.
This function is used to forward all data transmitted and received by the machine to a specified
destination (Scan to E-mail address, Scan to FTP destination, Scan to Network Folder destination,
14
TRADEMARK ACKNOWLEDGMENTS
The following trademarks and registered trademarks are used in conjunction with the
machine and its peripheral devices and accessories.
some jurisdictions. Wingdings is a registered trademark of Microsoft Corporation in
the United States and other countries. Marigold and Oxford are trademarks of Arthur
Baker and may be registered in some jurisdictions. Antique Olive is a trademark of
Marcel Olive and may be registered in certain jurisdictions. Hoefler Text is a trademark
of Johnathan Hoefler and may be registered in some jurisdictions. ITC is a trademark of
International Typeface Corporation registered in the United States Patent and Trademark
Office and may be registered in certain jurisdictions. Agfa is a trademark of the AgfaGevaert Group and may be registered in certain jurisdictions. Intellifont, MicroType
and UFST are trademarks of Monotype Imaging, Inc. registered in the United States
Patent and Trademark Office and may be registered in certain jurisdictions. Macintosh
and TrueType are trademarks of Apple Inc. registered in the United States Patent and
Trademark Office and other countries. PostScript is a trademark of Adobe Systems
Incorporated and may be registered in some jurisdictions. HP, PCL, FontSmart and
LaserJet are trademarks of Hewlett-Packard Company and may be registered in some
jurisdictions. The Type 1 processor resident in Monotype Imaging’s UFST product is
under licence from Electronics For Imaging, Inc. All other trademarks are the property
of their respective owners.
• Microsoft®, Windows®, Windows® XP, Windows Server® 2003, Windows Vista®, Windows Server®
2008, Windows® 7, Windows® 8, Windows Server® 2012 and Internet Explorer® are registered
trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Adobe and Flash are registered trademarks or trademarks of Adobe Systems Incorporated in the
United States and other countries.
• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or
trademarks of Adobe Systems Incorporated in the United States and other countries.
• Macintosh, Mac OS, AppleTalk, EtherTalk and LaserWriter are trademarks of Apple Inc.,
registered in the U.S. and other countries.
• Netscape Navigator is a trademark of Netscape Communications Corporation.
• Mozilla® and Firefox® are registered trademarks or trademarks of the Mozilla Foundation in the
U.S.A. and other countries.
• PCL is a registered trademark of the Hewlett-Packard Company.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• Sharp OSA is a trademark of Sharp Corporation.
• RealVNC is a trademark of RealVNC Limited.
• All other trademarks and copyrights are the property of their respective owners.
Candid and Taffy are trademarks of Monotype Imaging, Inc. registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions.
CG Omega, CG Times, Garamond Antiqua, Garamond Halbfett, Garamond Kursiv,
Garamond and Halbfett Kursiv are trademarks of Monotype Imaging, Inc. and may
be registered in certain jurisdictions. Albertus, Arial, Coronet, Gill Sans, Joanna
and Times New Roman are trademarks of The Monotype Corporation registered in
the United States Patent and Trademark Office and may be registered in certain
jurisdictions. Avant Garde, ITC Bookman, Lubalin Graph, Mona Lisa, Zapf Chancery
and Zapf Dingbats are trademarks of International Typeface Corporation registered
in the United States Patent and Trademark Office and may be registered in certain
jurisdictions. Clarendon, Eurostile, Helvetica, Optima, Palatino, Stempel Garamond,
Times and Univers are trademarks of Heidelberger Druckmaschinen AG, which may
be registered in certain jurisdictions, exclusively licenced through Linotype Library
GmbH, a wholly owned subsidiary of Heidelberger Druckmaschinen AG. Apple
Chancery, Chicago, Geneva, Monaco and New York are trademarks of Apple Inc.
and may be registered in certain jurisdictions. HGGothicB, HGMinchoL, HGPGothicB
and HGPMinchoL are trademarks of Ricoh Company, Ltd. and may be registered in
15
MX-2314N/MX-2614N/MX-3114N
START GUIDE
PRINTED IN FRANCE
TINSE5144GHZZ