Craftsman 113.177825 Owner`s manual

f
Save This Manual
For Future Reference
SEARS
owner's
manual
MODEL
NO.
113.177825
Serial
Number
Model and serial
numbers may be found
on the handle. You
should record both
model and serial
numbers in a safe place
for future use.
FOR YOUR
SAFETY
CRRFTSMRN®
12 GALLON
FULL BLOWING
WET/DRY VAC
• assembly
• operating
• repair parts
READ ALL
INSTRUCTIONS
CAREFULLY
Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A.
Part No. SP6113
Printed in Canada
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
WET/DRY VACS
If within one year from the date of purchase, this Craftsman Wet/Dry
Vac fails due to a defect in material or workmanship, Sears will repair it,
free of charge.
If this Craftsman Wet/Dry Vac is used for commercial or rental purposes, this warranty coverage applies for only 90 days from date of
purchase.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE
NEAREST SEARS SERVICE CENTER/DEPARTMENT
THROUGHOUT
THE UNITED STATES.
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Sears, Roebuck and Co., D817 WA, Hoffman Estates, IL. 60179
IMPORTANT SAFETY INSTRUCTIONS
Safety is a combination of common
sense, staying alert and knowing how
your vac works. Read this manual to
understand the vac.
Safety Signal Words
DANGER: means if the safety information
is not followed someone will be seriously
injured or killed.
WARNING: means if the safety information is not followed someone could be
seriously injured or killed.
CAUTION: means if the safety information is not followed someone may be
injured.
When using your Wet!Dry Vac, follow basic
safety precautions including the following.
• Do not vacuum, or use this Wet/Dry
Vac, near flammable or combustible
liquids, gases, or explosive dusts, such
as gasoline or other fuels, lighter fluid,
cleaners, oil- based paints, natural
gas, hydrogen, coal dust, magnesium
dust, grain dust, or gun powder.
• Do not use Wet/Dry Vac as a sprayer.
Do not vacuum anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
Do not vacuum fireplace soot or ash. This
is a very fine dust which will not be captured by the filter and may cause damage.
To avoid health hazards from vapors or
dusts, do not vacuum toxic materials.
Do not use or store near hazardous materials.
WARNING-To reduce
To avoid electric shock, do not expose to
rain. Store indoors.
the risk of fire, electric shock, or
injury:
Do not allow Wet/Dry Vac to be used as a
toy. Close attention is necessary when
used by or near children.
Do not use this Wet/Dry Vac with a torn filter or without the filter installed except
when vacuuming liquids as described in
the operation section of this manual.
Do not leave Wet/Dry Vac when plugged
in. Unplug from outlet when not in use and
before servicing. Turn off Wet/Dry Vac
before unplugging.
Read and understand this owner's manual
and all labels on the Wet/Dry Vac before
operating. Use only as described in this
manual. To avoid personal injury or damage to Wet/Dry Vac, use only Sears
Craftsman recommended accessories.
Sparks inside the motor can ignite flammable vapors or dust. To avoid fire or
explosion:
Toavoidinjuryfromaccidental
starting,
unplug
powercordbefore
changing
or
cleaning
filter.
Donotunplug
bypullingoncord.To
unplug,
grasptheplug,notthecord.
Donotusewithdamaged
cord,plugor
otherparts.If yourWet/Dry
Vacisnot
working
asitshould,
hasmissing
parts,
hasbeendropped,
damaged,
leftoutdoors,
ordropped
intowater,returnittoa
SearsService
Center.
Donotpullorcarrybycord,usecordas
handle,
closeadooroncord,orpullcord
around
sharpedges
orcorners.
Donot
runWet/Dry
Vacovercord.Keepcord
away
fromheated
surfaces.
Donothandle
plugortheWet/Dry
Vac
withwethands.
Donotputanyobject
intoventilation
openings.
Donotvacuum
withanyventilationopenings
blocked;
keepfreeofdust,
lint,hairoranything
thatmayreduce
air
flow.
Keephair,looseclothing,
fingers,
andall
partsofbodyaway
fromopenings
and
moving
parts.
Toavoidfalls,useextracarewhencleaningonstairs.
ThisWet/Dry
Vacisdouble-insulated,
eliminating
theneedfora separate
grounding
system.
Useonlyidentical
replacement
parts.Readtheinstructions
forServicing
Double-Insulated
Wet/Dry
Vacsbefore
servicing.
Observe
thefollowing
warnings
that
appear
onthemotorhousing
ofyourWet/
DryVac.
-_-]
GROUNDING
NOT REQUIRED
DOUBLE INSUL.ATEDWHEN SERVICING USE ONLY
IDENTICALREPLACEMENT PARTS
WARNING: To reduce the risk of
electric shock - do not expose to
rain - store indoors.
WARNING: For your own safety, read
and understand owner's manual. Do
not pick up hot ashes, coals, toxic,
flammable or other hazardous materials. Do not use around explosive
liquids or vapors.
SAVE THESE INSTRUCTIONS
The operation of any utility vac or blower
can result in foreign objects being blown
into the eyes, which can result in severe
eye damage. Always wear safety goggles
complying with ANSI Z87.1 (shown on
package) before commencing operation.
Safety Goggles are available at Sears
retail stores.
WEAR
YOUR
Use only extension cords that are rated
for outdoor use. Extension cords in poor
condition or that are too small in wire size
can pose fire and shock hazards. When
using an extension cord, be sure it is in
good condition. Using any extension cord
wilt cause some toss of power. To keep
the loss to a minimum, use the following
table to choose the minimum wire size
extension cord.
Extension
Cord Length
0-50 Ft
50-100 Ft
To avoid hearing damage, wear ear protectors when using the vac for extended
hours or when using it in a noisy area.
For dusty operations, wear dust mask.
A.W.G.
14
12
Introduction
This Wet/Dry Vac is intended for household use only.
IMPORTANT
Please
Read
NOTE
Carefully
Static Shocks Are Common - In dry
areas or when the relative humidity of the
air is low. To reduce the frequency of
static shocks in your home the best remedy is to add moisture to the air with a
console humidifier.
Owner's
Key
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Description ........................... Qty.
Vac Assembly ............................. 1
Hose Assembly ........................... 1
Utility Nozzle ............................... 1
Wet Nozzle .................................. 1
Car Nozzle .................................. 1
Hose Lock ................................... 1
Filter Nut ..................................... 1
Filter Plate ................................... 1
Filter (Red Stripe) ....................... 1
Filter Cage .................................. 1
Float ............................................
1
Extension Wands ........................ 2
Caster Foot For Storage ............. 4
Caster ......................................... 4
Owners Manual ........................... 1
Contents
Page
Warranty Information ............................. 2
Safety Instructions ................................. 2
Introduction............................................
4
Unpacking and Checking
Carton Contents ............................. 4
Assembly ...............................................
5
Operation ...............................................
8
Maintenance ........................................
10
Repair Parts ........................................
12
Unpacking and Checking
Remove entire contents of carton. Check
each item against the Carton Contents
List. Some units may include accessories
not shown. Notify your Sears Store immediately if any parts are damaged or missing.
Carton
Contents
List
Manual
Item
Carton Contents
A
J
M
m
Float/Cage Assembly
WARNING: For your own safety,
never connect plug to power source
outlet until all assembly steps are
complete and you have read and
understood the safety and operation
instructions. Do not operate vac
with any parts damaged or missing.
• Place the power assembly of vac
upside down into the drum•
2. Locate the float• Place the float over the
opening in the center of the lid with the
words "This Side Towards Lid" laying
face down over the hole.
NOTE: If fitter cage needs to be removed,
because the float is placed in the wrong
way, use a slotted screwdriver and insert
the blade near one of the tabs between
the filter cage and the center ring of the
lid. Pry the tab out of the slot. Tilt the cage
and lift away from the lid. To replace, follow float/cage assembly instructions•
Filter
Cage---_Tabs
Power
Assembly
/
WARNING: To reduce the risk of personal injury or damage to vac be
sure to keep hands, fingers, or any
other foreign objects out of the center opening when assembling the
float.
3. Line up filter cage tabs with the slots in
the center ring of the lid.
4. Push on the filter cage until the tabs
snap into the slots for a secure fit.
Cage
(3)
Slots (3)
Filter Assembly
1. Carefully slide the filter over the filter
cage, sliding it over the center ring covering the 3 slots until the filter stops
against the lid.
2. Place the hole in the filter plate over
threaded screw of the filter cage.
3. Gently push on the filter plate to seat
the rubber ring of the filter inside the circular channel of the filter plate.
4. Place filter nut onto threaded screw and
tighten it down. Finger tighten only.
NOTE: Lever of filter nut should be away
from plate as shown.
IMPORTANT: Do not overtighten as this
may deform or crack the filter plate or filter
cage.
NOTE: Your filter has a red stripe that
matches an in-store disptayer. When you
visit your local Sears store, just remember the
color of your stripe for the correct size filter.
_
Filter Nut
..,---- Filter Plate
-,,-- Filter
Red Stripe
Filter Cage
Caster/Caster
Foot Assembly
1. Remove the power assembly from the
dust drum and set aside.
7. Turn the drum upright.
2. Turn the dust drum upside down on the
floor.
3. Insert the caster feet into the bottom of
drum, as shown (4 places).
4. Push on the caster foot until the foot is
flush with bottom of the dust drum.
C as'e r ___.
5. Insert the caster stem into the socket of
the caster foot, as shown (4 places).
6. Push on the caster until the ball on the
caster stem is inserted all the way into
the socket. You wilt hear the ball snap
into the socket and the caster will swivel
easily when positioning is correct.
CcaaSt_rr
S;: i_
ou.,
Vac Assembly
1. Line up vacuum port in power assembly
with drain cap located on the front of
the drum.
4. Push down on top of the handles to
cause the flexible locking tabs to hook
onto the drum lip of the channel.
5. Make sure that the locking tabs are
snapped in place to prevent the power
assembly from coming off. (See inset
below.)
2. Place power assembly on top of drum
with the handles snug against the drum
channel.
3. Be sure power assembly completely
covers the top of the drum so leakage
does not occur.
/_Vacuum
,
cDaru
Lid_
__
_
_;:_
•
Assembly
Pull
Out
Flexible
Lockibng
_Ta
/_
Stop_
Tab
>...__
_
Handle
w'nmel_
._Power
_D_wn
Not Force Drain
Flexible
Beyond Stop Tab
Out
Drum
Flexible Locking Tabs
Port
6.Insertthesoftendofthehose,whichis
opposite
theswivelend,intothevacuumportdirectly
abovethedrain.
7.Placetheutilitynozzle
securely
onthe
swivel
endofthehoseandthevacis
ready
foruse.
Cord Wrap_.
Area
'"
NOTE: The swivel end of the hose is
removable if more hoses need to be
attached for more length from the vac. To
remove the swivel portion of the hose,
grasp the hose swivel and firmly pull it out
of the flexible hose. Connect the soft end
of a second hose (accessory #9-17820)
into the swivel end of the original hose by
forcing the sections together until they fit
tightly.
On-Off
Switch
Blowing
Port
Port
Lid
Swivel
End
Drum
Utility
Nozzle
Drain
Larger
Power
Assembly
/
Open End
Of Hose
Lock
To Store Your Accessories
1. Slide extension handles and accessories into the slotted areas of the
caster feet for storage.
2. To remove the accessories,
rotate and pull upward.
lightly
Hose
/
Operation
WARNING
To reduce the risk of fire or explosion, do not operate this vac in areas with
flammable gases, vapors or explosive dust in the air. Flammable gases or
vapors include but are not limited to; lighter fluid, solvent type cleaners, oilbase paints, gasoline, alcohol or aerosol sprays. Explosive dusts include but
are not limited to; coal, magnesium, grain or gun powder. Do not vacuum
explosive dust, flammable or combustible liquids or hot ashes. Do not use
this vac as a sprayer. To reduce the risk of health hazards from vapors or
dusts, do not vacuum toxic materials.
CAUTION: To reduce risk of hearing
damage wear ear protectors when
using the vac for extended hours or
when using it in a noisy area. The
operation of any utility vac can
result in foreign objects being
blown into the eyes, which can
result in severe eye damage. Always
wear safety goggles complying with
ANSI Z87.1 (shown on Package)
before commencing operation.
Safety Goggles are available at
Sears retail stores.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug wilt fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
After you plug the power cord into the outlet, turn the unit on by pushing the switch
from position "O" to position "t". The symbols used on the motor cover are international "On & Off' symbols. "0" is the
symbol for "OFF" and 'T' is the symbol for
"ON".
0 =oFF
Vacuuming
I =oN
Dry Materials
1. The filter must always be in correct
position to avoid leaks and possible
damage to vac.
2. When using your vac to pick up very
fine dust, it wilt be necessary for you to
empty the drum and clean the filter at
more frequent intervals to maintain
peak vac performance.
NOTE: A dry filter is necessary to pick up
dry material. If you use your vac to pick up
dust when the filter is wet, the filter will
clog quickly and be very difficult to clean.
3. If your filter is wet but you need to use
the vac to pick up dry material, you can
quickly dry the filter by running the vac
without hose attached for about 10 minutes. The clean air rushing through the
vac will help dry the filter.
NOTE: The optional Craftsman Fine Particle Filter, stock number 9-17916 wilt do
a better job stopping the very fine particles than the 9-17816 filter. This filter will
stop 99.99% of all particles as small as
.75 micron.
Vacuuming
Liquids
1. When picking up small amounts of liquid the filter may be left in place.
2. When picking up large amounts of liquid we recommend that the filter be
removed. If the filter is not removed, it
wilt become saturated and misting may
appear in the exhaust.
3. After using the vac to pick up liquids,
the filter must be dried to avoid possible
mildew and damage to the filter.
4. When the liquid in the drum reaches a
predetermined level, the float mechanism wilt rise automatically to cut off airflow. When this happens, turn off the
vac, unplug the power cord, and empty
the drum. You wilt know that the float
has risen because vac airflow ceases
and the motor noise wilt become higher
in pitch, due to increased motor speed.
IMPORTANT: To avoid damage to the
vac do not run motor with float in raised
position.
Emptying
the Drum
WARNING: To reduce the risk of
injury from accidental starting,
unplug power cord before emptying
the drum.
• The vac
for easy
unscrew
site side
comes equipped with a drain
emptying of liquids. Simply
the drain cap and lift the opposlightly to empty the drum.
2. Another option is to remove the power
assembly• Pull the flexible latches outward on each side of the lid to release
from the drum.
3. While holding the latches out, lift the
power assembly up and away from the
drum.
4. Lay power assembly upside down on a
clean area while emptying drum.
5. Dump the drum contents into the proper
waste disposal container•
WARNING: To reduce the risk of
back injury or falls, do not lift a vac
heavy with liquid or debris. Scoop
or drain enough contents out to
make the vac light enough to lift
comfortably.
Cord Wrap/Carry
Handle
The wet/dry vac has a convenient cord
wrap area/carry handle designed on the
rear of the vac. Simply, wrap the power
cord around the handle and snap the connector on the plug to a wrap of the cord
and the cord is wrapped for storage•
Moving
the Vac
1. Should it become necessary to pick the
vac up to move it, DO NOT pick the vac
up by the lid handles unless dust drum
is empty• To avoid dropping the vac due
to latches releasing or possible part
breakage, pick the vac up by the lip of
the dust drum.
Blowing
Feature
Your vac features "Full Blowing"• It can
blow sawdust and other debris• Follow the
steps below to use your vac as a blower•
WARNING: Always wear safety gog- I
gles complying with ANSI Z87.1
before using as a blower.
I
WARNING: To reduce the risk of
injury to bystanders, keep them
clear of blowing debris.
1. Locate blowing port of your vac.
2. Insert soft end of your hose into blowing
port.
3. (Optional) Attach extension wand to
swivel end of hose, then place a blower
nozzle on the wand.
4. Turn vac on and you are ready to use
your vac as a blower•
Sears recommended accessories are
available at Sears retail stores• The Sears
Blower Nozzle Stock No. 9-16933 and
extension handles Stock No. 9-16964 are
recommended for blowing debris•
End
Swivel End
_f Hose
Extension
Wand
)ptional)
Blowing
Nozzle
(Optional)
I
I
Maintenance
Filter
IMPORTANT: To avoid damage to the
blower wheel and motor, always reinstall
the filter before using the vac for dry material pickup.
WARNING: To reduce the risk of
injury from accidental starting,
unplug power cord before changing
or cleaning filter.
Dry Filter
1. Some removal of dry debris can be
accomplished without removing the fitter from the vac. Slap your hand on top
of the power assembly while the vac is
turned off.
NOTE: This filter is made of high quality
paper designed to stop very small particles of dust. The filter can be used for wet
or dry pick up. Handle the filter carefully
when removing to clean or installing it.
Creases in the filter pleats may occur from
installation but creases will not affect the
performance of the filter.
2. For best cleaning results due to accumulated dust, clean the filter in an open
area. Cleaning SHOULD be done outdoors and not in the living quarters.
Cleaning
Your filter should be cleaned often to
maintain peak vac performance.
3. After filter removal from vac, remove the
dry debris by gently tapping the filter
against the inside wall of your dust
drum. The debris will loosen and fall.
Be sure to dry the filter before storing or
picking up dry debris.
4. For thorough cleaning of dry filter with
fine dust (no debris), run water through
it as described under "Wet Filter".
IMPORTANT: After cleaning, check the
filter for tears or small holes. Do not use a
filter with holes or tears in it. Even a small
hole can cause a lot of dust to come out of
your vac. Replace it immediately.
Wet Filter
After filter is removed, run water through
the filter from a hose or spigot. Take care
that water pressure from the hose is not
strong enough to damage filter. Remember: To dry a filter quickly, reinstall the fitter on the vac and allow the unit to run for
approximately 10 minutes. The clean air
rushing through the filter will dry it.
Removal
To remove the filter for cleaning or
replacement, unscrew the filter nut from
the filter cage, remove filter plate and lift
off filter.
WARNING: Do not remove the filter
cage. It is there to help prevent your
fingers from getting into the blower
wheel.
Installation
Refer to page 5, "Filter Assembly".
Allow the filter to dry before storing the
vac.
Wet/Dry
Vac
To keep your Wet/Dry Vac looking its best,
clean the outside with a cloth dampened
with warm water and mild soap.
To clean the drum:
WARNING: To assure product
SAFETY and RELIABILITY, repairs
and adjustment should be performed by Sears Service Centers,
always using Sears replacement
parts.
1. Dump debris out.
2. Wash drum thoroughly with warm water
and mild soap.
NOTE: If your casters are noisy, you may
put a drop of oil on the roller shaft to make
them quieter.
3. Wipe out with dry cloth.
10
Wet Nozzle
farthest from you.)
To pick up liquids off a smooth surface,
use the 2-1/2" wet nozzle accessory supplied with your wet/dry vac. To use this
nozzle, simply attach the nozzle to the
end of an extension wand.
Connect a second extension wand to the
first, and connect the 2-1/2" x 7' hose to
the extension wand.
Liquids may be picked up by dragging the
nozzle across the surface. The squeegee
will dry the surface as you vacuum.
Replacement rubber for the squeegee
nozzle may be obtained through Sears
Parts. If the rubber becomes worn, it may
be flipped over for use on the opposite
side or replaced. (Replacement service
part #822256). To reverse or replace the
squeegee:
1. Lay the wet nozzle on a flat surface with
the round inlet opening facing up and
the two latches close to you as shown.
Latches
i
,
Nozzle
2.
Using both hands, lower the nozzle
body onto the insert and squeegee with
the round opening of the nozzle closest
to you. With fingers on the far side and
thumbs holding the latches of the
removable insert, flip the nozzle over so
the latches are on the top and the round
inlet opening is facing away from you.
Make sure the squeegee stays on the
insert pins.
3. Press down with each thumb below the
latching tabs until you see and hear the
removable insert snap into the nozzle
body. Snap the latches over the locking
tabs into their original position.
4. Inspect the pins of the insert to make
sure they fit through the holes of the
squeegee and fit into the matching slots
in the nozzle body.
2. Using both hands, position each thumb
on the removable insert, (below the
latches) and two fingers of each hand
on each latch, lift and disengage the
two latches from the tabs on the nozzle
body.
NOTE: If the pins are out of position,
hold the nozzle assembly with both
hands and gently twist in opposite
directions. The insert pins should snap
into proper position.
Twist
Twist
Backward
Forward
3. Gently pull the latches toward yourself
to remove the insert.
To reinstall the removable insert correctly,
follow these steps:
1. Place the removable insert on a flat surface with the pins positioned upward
and the latches close to you as shown.
Place the rubber squeegee on the
insert, with the pins fitting through the
matching holes in the squeegee. (Make
sure the new working edge is located
The wet nozzle assembly is ready for wet
pickup use.
11
Repair Parts
12 Gallon Wet/Dry Vac
Model Number 113.177825
Always order by Part Number - Not by Key Number
WARNING
SERVICING
OF DOUBLE-INSULATED
WET/DRY
VAC
In a double-insulated Wet/Dry Vac, two systems of insulation are provided
instead of grounding. No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added. Servicing a doubleinsulated Wet/Dry Vac requires extreme care and knowledge of the system, and
should be done only by qualified service personnel. Replacement parts for a
double-insulated Wet/Dry Vac must be identical to the parts they replace. Your
double-insulated Wet/Dry Vac is marked with the words "DOUBLE INSULATED"
and the symbol _(square
ance.
Key
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2O
within a square) may also be marked on the appli-
Part No.
73180
824941
823687-2
824967
STD611007
818793
818961
818413-2
15534-1
73316
823683-4
509238
9-17816
9-16937
9-16938
73332
73185
9-16990
73102
9-17820
822256
SP6113
Description
Toggle Switch
Motor Cover
Cord w/ptug
Motor (Includes Key No's 7,thru 10)
* Screw, Pan Hd. Ty "AB" 10x3/4
Lid Gasket
Spacer
Blower Wheel
Washer
Nut, Hex Flange 1/4-20
Lid
Float/Filter Cage
1"Filter (Red Stripe)
1"Filter Plate
1"Filter Nut
Dust Drum
Drain Cap
1"Caster Foot w/Storage
Casters
1"Hose 2-1/2" x 7'
Squeegee (Not Illustrated)
Owners Manual (Not illustrated)
1 Stock Item - Ma_' Be Secured Through The Hardware Department
Stores
* Standard Hardware Item - May Be Purchased Locally.
12
Of Most Sears Retail
Repair Parts
12 Gallon Wet/Dry Vac
Model Number 113.177825
/
2
J
J
J
J
I
I
16
/
197_
13
CRRFTSMRN®
Accessories
and Attachments
Get more versatility from your Craftsman wet/dry vacuum by adding these accessories.
Additional wet/dry vac accessories may be purchased at your local Sears retail store
or Sears/Craftsman Power and Hand Tool Catalog.
17820 2-1/2"x7' Hose
16964 Extension Wands
16922 Utility Nozzle
17817 Wet Nozzle
16978 Car Nozzle
16915 Multipurpose
Floor Tool
16947, 16948
Inflator Nozzle
NOTE: Most Accessories
16933 Blower Nozzle
16926 14" Floor
Brush
17816 Paper Pleated
Filter
16931/16990 Caster
Feet for Storage
16925 Dry Nozzle
16902 Crevice Tool
16901 Dusting
Brush
16939 & 16940
Drum Liners
Are Available In 2-1/2 Inch And 1-1/4 Inch Sizes
14
HoseLock 16935
GutterNozzle
16934
HoseGrip 16917HoseJoiner 16930
Sawdust Collection
Radial Arm Saw
Dust Collection Kit
29963
Series
Table Saw Dust
Collection Kit
29962
15
For the repair or replacement parts you need
Gall 7 am - 7 pro, 7 days a week
1-800-366-PART
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day, 7 days a week
1-800-4-REPAIR
(1-800-473-7247)
Forthe location of a
Sears Repair Service Center in yourarea
Call 24 hours a day, 7 days a week
1-800-488-1222
For information on purchasinga Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am - 5 pro, Monday-Saturday
1-800-827-6655
SEARS
g;t=;/', r/;l.._f:;t
rt[#:_#
America's
Repair
Speoahsts
The model and serial numbers will be found on the handle.
When requesting service or ordering parts, always provide the
following
information:
•
•
Product Type
Part Number
•
•
Model Number
Part Description
@1999 Emerson Electric Co.
Part No. SP6113
Sears, Roebuck and Co., Chicago, IL. 60179 U.S.A.
Form No. SP6113-1
Printed in Canada 10/00