Craftsman evolv 320.17263 Operator`s manual

Operator's
Manual
j CRRFTSMRH°j
evolv M
3.6 Volt SCREWDRIVER
Model No. 320.17088
0Q0s
CHARGE BATTERY
BEFORE FIRST USE
WARNING:
To reduce
the risk of
injury, the user must read and
understand the Operator's Manual
before using this product.
Sears Brands
www.craftsman.com
Management
Corporation
• WARRANTY
SAFETY
ASSEMBLY
OPERATION
MAINTENANCE
Warranty
SafetySymbols
SafetyInstructions
Description
Assembly
Operation
Maintenance
Troubleshooting
Exploded
ViewandPartList
SearsRepairPartsPhoneNumber
page2
page3
page4-9
page9-10
page10-11
page12-14
page15
page15
page16-17
BackCover
CRAFTSMAN
®EVOLVFULLWARRANTY
IfthisCraftsman@
Evolvtoolfailsto givecomplete
satisfaction
within
oneyearfromthedateofpurchase,
returnitto anySearsstoreor other
Craftsman@
EvolvoutletintheUnitedStatesforfreereplacement.
Thiswarranty
isvoidifthisproductis everusedforcommercial
or rental
purposes.
Thiswarranty
givesyouspecificlegalrights,andyoumayalsohaveother
rights,whichvaryfromstateto state.
Sears,Roebuck
andCo.,Hoffman
Estates,
IL60179
A
J_, WARNING:
Some dust created by using power tools contains
known to the state of California to cause cancer and birth defects
reproductive
chemicals
or other
harm.
SAVE THESE INSTRUCIONS!
READ ALL iNSTRUCTiONS!
17088 Manual
Revised 09-0728
Page 2
The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding.
The symbol warnings do not, by themselves,
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
,_ WARNING:
Be sure to read and understand all safety instructions in this
manual, including all safety alert symbols, such as "DANGER," "WARNING,"
and "CAUTION,"
before using this screwdriver. Failure to following all
instructions listed below may result in electric shock, fire and/or serious personal
injury.
SYMBOL
MEANNING
SAFETY
ALERT SYMBOL:
May be used in conjunction
,_
DANGER:
Indicates
DANGER,
with other symbols
WARNING,
Failure to obey this safety warning will result in death or serious
injury to yourself or to others. Always follow the safety precautions
risk of fire, electric shock, and personal injury.
,_
WARNING:
CAUTION:
to reduce the
Failure to obey this safety warning may result in death or serious
injury to yourself or to others. Always follow the safety precautions
risk of fire, electric, shock and personal injury.
DAMAGE
to reduce the
Failure to obey this safety warning can result in death or serious
injury to yourself or to others. Always follow the safety precautions
risk of fire, electric shock, and personal injury.
,_
OR CAUTION.
or pictographs.
PREVENTION
AND INFORMATION
to reduce the
MESSAGES
These inform user of important information and/or instructions that could lead to
equipment or other property damage if not followed. Each message is preceded
by the word "NOTE" as in the example below.
NOTE: Equipment and/or property damage may result if these instructions are
not followed.
WEAR
YOUR
The operation of any power tool can result in foreign
objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool
operation, always wear safety goggles or safety glasses
with side shields and a full-face shield when needed.
We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields,
available at Sears Stores or other Craftsman outlets.
Always use eye protection
ANSI Z87.1
17088 Manual
Revised
09-0728
that is marked to comply
with
Page 3
WARNING:
Read all safety warnings and instructions.
warnings and instructions
Failure to follow the
may result in electric shock, fire and / or serious injury.
WARNING:
Do not attempt to operate this tool until you have thoroughly
read all instructions, safety rules, and warnings. Failure to comply with them can
result in fire, electric shock, or serious personal injury. Save the manual and refer
to it frequently.
Save all warnings
and instructions
for future
reference.
The term power tool in the warnings refers to your mains-operated
power tool or battery-operated
(cordless) power tool.
GENERAL
WORK
SAFETY
(corded)
PRECAUTIONS
AREA SAFETY
•
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres,
such as in the
presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
•
Keep children and bystanders
away while operating
Distractions cause you to lose control.
a power tool.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded)
power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
* Avoid body contact with earthed
surfaces such as pipes, radiators,
refrigerators.
There is an increased
if your body is earthed or grounded.
or grounded
ranges and
risk of electric
shock
e Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of electric shock.
o Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging
the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
= When
outdoor
shock.
operating
a power tool outdoors,
use an extension
cord suitable for
use. Use of a cord suitable for outdoor use reduces the risk of electric
= if operating a power tool in a damp location is unavoidable,
use a residual
current device (RCD} protected supply. Use of an RCD reduces the risk of
electric shock.
17088 Manual
Revised 09-0728
Page 4
PERSONAL SAFETY
=
Stay alert, watch what you are doing and use common sense when
operating
a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication.
A moment of inattention while
operating power tools may result in serious personal injury.
=
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing,
and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
=
Prevent unintentional
starting. Ensure the switch is in the off-position
before connecting
to power source and / or battery pack, picking up or
carrying the tool. Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on invites accidents.
=
Remove any adjusting
key or wrenches before turning the tool on. A
wrench or a key that is left attached to a rotating part of the tool may result in
personal injury.
=
Do not overreach. Keep proper footing and balance at all times.
footing and balance enables better control of the tool in unexpected
situations.
•
Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce personal
injuries.
•
If devices are provided for the connection
of dust extraction
and
collection
facilities,
ensure these are connected
and properly used. Use
of these devices can reduce dust-related hazards.
Proper
POWER TOOL USE AND CARE
Do not force tool. Use the correct tool for your application.
The correct
tool will do the job better and safer at the rate for which is designed.
Do not use tool if switch does not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect
the plug from the power source and/or the battery pack
from the power tool before marking any adjustments,
changing
accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
Store idle tools out of reach of children and other untrained
Tools are dangerous in the hands of untrained users.
persons.
Maintain tools with care. Check for misalignment
or binding of moving
parts, breakage of parts, and any other condition that may affect the
tools operation,
if damaged,
have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
17088 Manual
Revised 09-0728
Page 5
Keep cutting
sharp cutting
tools sharp and clean. Properly maintained cutting tools with
edges are less likely to bind and are easier to control.
Use the power tool, accessories
and tool bits etc., in accordance
with
these instructions,
taking into account the working conditions
and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
BATTERY
TOOL USE AND CARE
•
Recharge only with the charger specified
by the manufacturer.
A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
•
Use power tools only with specifically
designated battery
any other battery packs may create a risk of injury and fire.
•
When battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects,
that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
•
Under abusive conditions,
liquid may be ejected from the battery;
avoid contact, if contact accidentally
occurs, flush with water, if liquid
contacts
eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
packs.
Use of
SERVICE
•
Have your power too[ serviced by a qualified repair person using only
identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SAFETY
SYMBOLS
FOR YOUR TOOL
The label on your tool may include the following
V ...............................................................
Volts
A ...............................................................
Amps
Hz .............................................................
Hertz
W ..............................................................
Watts
min ...........................................................
Minutes
...... I.....................................................
I __-== ...I .....................................................
symbols.
Alternating Current
D rect Current
n.............................................................
No-load
[] ..............................................................
Class II construction
.../min .......................................................
Revolutions
_,
Indicates danger, warning caution.
It means attention! Your safety is
involved.
...........................................................
17088 Manual
Revised 09-0728
Speed
or Strokes
per minute
Page 6
SPECiFiC
SAFETY
WARNING:
RULES FOR SCREWDRIVER
To avoid injury, hold the tool by the insulated gripping
surfaces
only. if the tool contacts hidden wiring or its own cord, exposed metal parts
of the tool could shock the operator and cause serious injury. Make sure that
hidden electrical wiring, water pipes, or other hazards are not in the cutting path.
WARNING:
To reduce the risk of injury, user must read instruction
manual.
,,
Do not use dull or damaged
bits and accessories.
*
Only connect
*
Before screwing into a wall, check with a metal/voltage
detector
you are not driving into an electricity, gas, or water supply line.
to be sure
*
Avoid frequent
the tool.
*
if the tool stalls, release the trigger immediately,
reverse the direction
rotation and slowly squeeze trigger to back out the bit.
*
Do not expose
moisture.
the power unit to a 120V AC supply.
stalling
the tool
when operating,
as this could damage
of
and power unit to rain; also protect them from
To protect the batteries
from
temperature above 50 degrees
damage, you should
centigrade. (122 ° F)
Do not charge the tool in a damp
reduce the risk of electric shock.
or wet location.
never expose them to
Following
this rule will
,,
Do not operate power unit with a damaged cord or plug. if damaged, it
should be replaced immediately. Contact or visit the nearest Sears service
center for more information.
,,
Do not operate power unit if it has received a sharp blow, been dropped,
or otherwise damaged in any way; take it to a qualified serviceman or
contact or visit the nearest Sears service center for more information.
,,
Disconnect
power unit from power supply when not in use. Following
rule will reduce the risk of electric shock, fire, or serious personal injury.
,*
This power unit is intended
floor mount position.
SAFETY
,_
to be correctly
orientated
this
in a vertical or
RULES FOR POWER UNIT
WARNING:
instructions
injury.
Read and understand
all instructions.
Failure to follow all
listed below may result in electric shock, fire and/or
serious
personal
Before using Power Unit, read all instructions and cautionary markings in this
manual, on the power unit,, and the product using battery to prevent misuse of
the products and possible injury or damage.
CAUTION:
To reduce the risk of electric shock or damage
and rool, charge only this Ni-cad rechargeable
17088 Manual
Revised
09-0728
to the power unit
tool .Other types of batteries
may
Page 7
burst, causing
personal
injury or damage.
Do not use Power unit outdoors or expose to wet or damp conditions.
Water entering charger will increase the risk of electric shock.
=
Use of an attachment
not recommended
or sold by the manufacturer
may result in a risk of fire, electric shock or injury to persons. Following
this rule will reduce the risk of electric shock, fire or serious personal injury.
Do not abuse cord or power unit. Never use the cord to carry the power
unit. Do not pull the cord rather than the plug when disconnecting
from
receptacle. Damage to the cord or power unit could occur and create an
electric shock hazard. Replace damaged cords immediately.
Make sure cord is located so that it will not be stepped on, tripped
over, come in contact with sharp edges or moving parts or otherwise
subjected
to damage or stress. This will reduce the risk of accidental falls,
which could cause injury and damage to the cord, which could result in
electric shock.
Keep cord and power
internal parts.
unit from
heat to prevent
damage
to housing
or
Do not let gasoline, oils, petroleum=based
products, etc. come in
contact with plastic parts. They contain chemicals that can damage,
weaken or destroy plastic.
An extension
cord should not be used unless absolutely
necessary.
Use of improper
extension
cord could result in a risk of fire and electric
shock. If an extension
cord must be used, make sure:
That pins on plug of extension
hose of plug on charger.
1.
.
3.
That extension
cord are the same number,
cord is properly
wired and in good electrical
That wire size is large enough
below:
25'
50'
100'
Cord Size(AWG)
16
16
16
•
condition;
and
for AC ampere rating of charger as specified
Cord Length (Feet)
NOTE: AWG = American
size and shape as
Wire Gauge
Do not operate the power unit with a damaged cord or plug, which could
cause shorting and electric shock, if damaged, have the power unit repaired
or replaced by an authorized service technician at Sears Service Center.
Do not operate power unit if it has received a sharp blow, been dropped
or otherwise damaged in any way. Take it to an authorized service
technician at Sears Service Center for an electrical check to determine if the
power unit is in good working
Do not disassemble
17088 Manual
Revised
09-0728
order.
power unit. Take it to an authorized
service technician
Page 8
at Sears Service Center when service or repair is required.
reassembly may result in a risk of electric shock or fire.
Incorrect
=
Disconnect power unit from the power supply when not in use.. This will
help prevent damage to the power unit during a power surge.
*
Risk of electric shock. Do not touch uninsulated
connector or uninsulated battery terminal.
•
Save these instructions. Refer to them frequently and use them to instruct
others who may use this tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and possible injury.
IMPORTANT
SAFETY
INSTRUCTIONS
•
Save these
*
Before using power unit, read all instructions
battery power unit, and product using battery.
CAUTION:
batteries
,_
instructions.
personal
markings
on
injury or damage.
When using electric appliances,
always be followed,
a)
and cautionary
To reduce the risk of injury, charge only this tool. Other types of
may burst, causing
WARNING:
portion of output
including
basic precautions
To reduce the risk of injury, close supervision
appliance is used near children.
b) Only use attachments
should
the following.
recommended
is necessary
when an
or sold by manufacturer.
c)
Do not use outdoors.
d)
For a portable appliance - To reduce the risk of electrical shock, do not put
the screwdriver and Battery Pack in water or other liquid. Do not place or
store appliance where or can fall or be pulled into a tub or sink.
k_, WARNING:
Contains
disposed of properly.
nickel-cadmium
WARNING:
Do not dispose
product may explode or leak.
17088 Manual
Revised
09-0728
battery.
of this product
Battery must be recycled
in fire,
batteries
or
in side this
Page 9
_I_ WARNING:
Your screwdriver
should never be attached
to the power unit
when you are assembling parts, making adjustments, installing or removing bits,
cleaning, or when it is not in use. When unpacking the box, do not discard any
packing materials until all of the contents are accounted for:
1.
2.
Carefully
surface.
lift the screwdriver
out of the carton and place it on a stable, flat
Open the box to locate the following:
®
Screwdriver
®
Power unit
®
Operator's
manual
3.
Inspect the items carefully to make sure that no breakage or damage has
occurred during shipping. If any of the items mentioned is missing, (refer to
"PARTS LIST" illustration), return the screwdriver to your nearest Sears store
or Craftsman outlet to have the screwdriver replaced.Carefully
remove the
tool and any accessories from the box. Make sure that all items listed in the
packing list are included.
,_
WARNING:
If any part is broken or missing, do not attempt
to assemble
the
screwdriver, attach the power unit, or operate the screwdriver until the broken or
missing part has been replaced. Failure to do so could result in possible serious
injury.
CARTON
CONTENTS/LOOSE
PARTS (Fig. 1)
Screwdriver
Power unit
KNOW YOUR SCREWDRIVER
(Fig. 1)
Before attempting to use this screwdriver, familiarize
operating features and safety requirements.
yourself with all its
The screwdriver is a light-duty tool for tightening and loosening screws. It is
lightweight and easy to use, featuring both a forward / reverse indicator and a
17088 Manual
Revised
09-0728
Page 10
work light. To secure your new rechargeable
screwdriver from possible failure, the battery
is in a low-charge condition when initially
shipped. Therefore, you should charge it
at for least 10 hours prior to use. Charging
your tool for at least 10 hours during the
first cycle of use will insure optimum battery
performance.
_,
WARNING:
Do not allow familiarity
Fig. 1
with
your screwdriver to make you careless.
Remember that a careless fraction of a
second
injury.
is sufficient
',_ +_
Charging
indicator
Charging Socket
\.II-_./
enough to inflict severe
PRODUCT
Power Unit
SPECIFICATIONS
Input: 120V~60HZ
Power unit
Output:
Rechargeable
3xl .2=3.6V DC Ni-Cd
battery
Normal charging
3-5 hours
time
Forward/Reverse
6V, DC 300mA
rotation
YES
LED Worklight
YES
Collet size
1/4" hex Collet
WARNING:
The safe use of this product
requires an understanding
of the
information on the tool and in this operator's manual as well as knowledge of the
project you are attempting. Before use of this product, familiarize yourself with
all operating features and safety rules.
ON/OFF
TRIGGER
SWITCH
To turn the tool on, press the trigger switch.
trigger switch.
FORWARD/REVERSE
The forward/reverse
running.
SCREWDRIVER
To turn the tool off, release the
SWITCH
switch should only be operated
when the motor is NOT
BiT COLLET
To hold 1" bits, bit holder, and socket adaptor.
WORK LIGHT
17088 Manual
Revised 09-0728
Page 11
For low light situations.
POWER UNIT
After the initial charging
optimum performance.
TO CHARGE
cycle, the tool should
be charged
for 3-5 hours for
(FIG. 2)
Make sure your screwdriver
charge it.
has completely
Insert the power unit plug into
charging socket, making sure
they are properly connected.
stopped
before attempting
to
Forward/
Reverse
Switch
Fig. 2
Power unit can be used with
normal house voltage of 120
volts, 60 Hz, AC only.
Connect the power unit to the
power supply.
Once the screwdriver
is initially
charged for at least 10 hours,
optimum performance can
be reached by recharging the
screwdriver for 3-5 hours after
use. It is not recommended
to
recharge
the screwdriver
Bit Collet
On/Off Trigg_
Switch
LED worklight
for less than 3 hours or more than 15 hours after each
use.
Do not place the power unit in an area of extreme
normal room temperature.
Fig. 3
The base of tool or power unit
may become warm during
charging.
iNSTALLiNG
heat or cold. It works best at
SCREWDRIVER
BiTS (Fig.3)
Place a 1/4" bit directly into the
screwdriver collet, or, insert it
into the magnetic bit holder and
then insert the bit holder into
the screwdriver collet.
Note: Your screwdriver is
intended for light=duty use.
17088 Manual
Revised
09-0728
Page 12
For best results,
1/4" screwdriver
Never engage the trigger
bits are recommended.
switch
when changing
Always lock the trigger switch when changing
switch instructions)
FORWARD/REVERSE
SWITCH
screwdriver
bits.
drill bits. (See forward/reverse
(Fig.4)
The forward/reverse
switch determines the running direction of the tool and also
serves as a trigger switch lock.
Fig. 4
FORWARD
REVERSE
To select "forward" motion,
release the trigger switch and
push the forward/reverse
lever
to the right side of the tool.
To select "reverse" motion,
push the forward/reverse
lever
to the left side of the tool.
The center position of the
switch locks the tool in the
"OFF" position.
When changing the position of
the switch, be sure the trigger
is released.
,_
WARNING:
SWITCH
LOCKED IN CENTER POSITION
Charging time must not exceed
15 hours; the battery
may be
damaged with excessive charging. Avoid charging your screwdriver in freezing
conditions. The power unit provided must only be used with this screwdriver
and not with any other products. Do not insert metal objects into the power unit.
Never change the forward/reverse
switch while the screwdriver is rotating as this
will damage the screwdriver.
,_
WARNING:
by a qualified
,_
WARNING:
To ensure safety and reliability,
service technician
all repairs should
be performed
at a Sears Service Center.
For your safety, always turn off the switch and remove the
battery pack from the tool before performing
any maintenance
or cleaning.
Periodic maintenance of your screwdriver allows for long life and trouible-free
operation. A cleaning, and maintenance schedule should be maintained.
As a common-sense
and preventive
recommended
steps:
maintenance
practice,
follow these
•
Inspect
•
Use a soft clean and damp cloth to wipe the tool housing.
17088 Manual
the bit; check the rim for wear or damage.
Revised
09-0728
A mild detergent
Page 13
can be used but nothing like alcohol, gasoline, or other such leaning agents.
Never use caustic agents to clean plastic parts.
WARNING: Always wear safety goggles or safety glasses with side shields
during power tool operations or when blowing dust. If operation is dusty, also
wear a dust mask.
WARNING:
Keep the tool air vents unclogged
WARNING:
Avoid using solvents
when cleaning
and clean at all times.
plastic
parts. Most plastics
are susceptible to damage from various types of commercial solvents and may
be damaged by their use. Use a clean cloth to remove dirt, dust, oil, grease, etc.
,_
WARNING:
Do not at any time let brake fluids, gasoline,
products, penetrating
can damage, weaken
injury.
WARNING:
17088 Manual
petroleum-based
oils, etc. to come in contact with plastic parts. Chemicals
or destroy plastic which may result in serious personal
Water must never come into the tool.
Revised
09-0728
Page 14
PROBLEM
The screwdriver
not work
17088 Manual
does
Revised 09-0728
CAUSE
SOLUTION
Battery pack is
exhausted
Recharge the battery
pack
Page 15
Screwdriver
Always
MODEL NUMBER
320.17088
mention the Model Number when ordering
/
J
parts for this tool
\
\
\
\
\
\
\\\\\\\\\\\\\\\
I c_<:,
17088 Manual
Revised 09-0728
Page 16
1
43789
Left Housing
1
2
43773
Round Pin
1
3
43791
Reversing
Levers
1
4
43792
Ornament
Cover
1
5
70286
Tapping
6
01109
Reed
1
7
TH0709-7
Gear Box
1
8
43790
Switch Button
1
9
70362
Tapping
5
10
43789
Right Housing
1
11
43774
Spring
1
12
34700
Current-conducting
13
43771
Reversing
14
43772
Charging
15
92119
Paper Washer
2
16
90169
Battery Pack
1
17088 Manual
Revised 09-0728
Screw
1
Screw
Plate
Levers Circuit
Circuit Board
1
Board
1
1
Page 17
17088
Manual
Revised 09=0728
Page 18
17088 Manual
Revised 09=0728
Page 19
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it !
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
(1-800-469-4663)
www.sears.com
®
Call anytime, day or night
(U.S.A. and Canada)
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
[:;
www,sears.com
1-800-469-4663
(Canada)
www,sears.ca
To purchase a protection agreement on a product serviced by Sears:
:if::
iI
1-800-827-6655
(U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR ®
Au Canada pour service en francis:
I_800_LE_FOYERMC
(1-800-533-6937)
(1-888-784-6427)
www.se a rs.ca
© Sears Brands, LLC
® Registered Trademark / TMTrademark / SMService Mark of Sears Brands, LLC
® Marca Registrada / TMMarca de Fabrica / SMMarca de Servicio de Sears Brands, LLC
MCMarque de commerce / MDMarque depos6e de Sears Brands, LLC