Bosch HBL 65.. Technical data

BOSCH
INSTALLATION
INSTRUCTION
for
Bosch Electric Built-in
MANUAL
Single & Double Oven Models HBL 53..154../55../56..
_3
BEFORE
YOU
BEGIN,
i_z)
READ
IMPORTANT:
INSTALLER:
Save
THESE
these inst.ru, ctions
Please
OWNER:
INSTRUCTIONS
for the local
leave this manual
Please
COMPLETELY
with owner
keep this manual
electrical
AND
inspector's
for future
for future
CAREFULLY
reference
reference.
use
|
J
Table of Contents
INTRODUCTION
.......................................................................................................................
3
Tools You Will Need ...................................................................................................................
3
Power
3
Requirements
Choosing
....................................................................................................................
Oven Location
Steps for Installation
TECHNICAL
Single
.........................................................
.................................................................
3
_..........................................................
3
4
oven ...................................................................................................................................
4
oven ..................................................................................................................................
4
UNDERCOUNTER
SINGLE
WALL
............................................
DATA .........................................................................................................................
Double
INSTALLATION
DOUBLE
ELECTRICAL
WIRING
..................................
; ..............................................................................
5
5
6
OVEN ............................................................................................................................
6
OVEN ..........................................................................................................................
7
SUPPLY
..................................................................................................................
REQUIREMENTS
CONNECTING
ELECTRICAL
..........................................................................................
OVEN ............................................................................................................................
INSTALLATION
SINGLE
.................................
TO 208 VOLT CIRCUIT
CONNECTIONS
;;...................................................................
...............................................................................
8
8
9
...................................................................................................
10
3-WIRE
BRANCH
CIRCUIT
.....................................................................................................
10
4-WIRE
BRANCH
CIRCUIT .....................................................................................................
10
FINAL
2
......
CHECKLIST
........................................................................................................................
11
INTRODUCTION
Please
read these instructions
COMPLETELY
AND CAREFULLY.
They will save you time and
effort and help to ensure optimum oven performance. Be sure to observe all WARNINGS.
These installation
instructions are intended for
use by a qualified installer. In addition to these instructions the oven shall be installed:
• In the United States, in accordance
with the National Electric Code/State and Municipal
codes
and/or local codes.
• In Canada,
tric Code
in accordance
with Canadian
C22.1-1atest
edition/Provincial
Municipal
These
codes and/or
shall be carefully
Note:
Elecand
followed
at all times.
The UL Canadian
listing mark consists of the circled UL symbol preceded by the letter "C", as
shown. This should appear on the oven's rating
plate along with the UL United
States listing
mark, which is the circled UL symbol above but
not preceded
by the letter "C".
YOU
The following
cook-top:
• Tape
WILL
to install your new
or ruler
screwdriver
are for the cook-top.
CHOOSING
OVEN
• Wire cutters
and wire stripper
• 1" hole saw
• Hand or saber
saw.
REQUIREMENTS
The oven must be supplied with the proper voltage and frequency.
The oven is manufactured
to
be connected
to a three wire or four wire, single
• .phase, 240 volt, 60 Hz AC electrical
supply on a
separate circuit fused on both sides of the line. If
LOCATION
Carefully
select the location where the oven will
be placed. The oven should be located for convenient use in the kitchen,
but away from strong
drafts. Strong drafts may be caused by open doors
or windows, or by heating
and/or air conditioning
vents or fans. Make sure that electrical power can
be provided to the location selected.
STEPS
FOR
INSTALLATION
The following
pages provide the necessary
information
for proper
installation
of the oven arranged as follows:
• Technical
Data
Cutout
Dimensions,
and Mounting instructions
> Undercounter
Installation,
Installation,
>Wall Installation,
• Electrical
Supply
• Modifications
Volt Circuit.
• Level
POWER
ers/fuses
>Wall
and straightedge
• Pencil
• Phillips
It is recommended
that you have the electrical
wiring and hook-up of your oven performed
by a
qualified
electrician.
After installation
is complete have the electrician
show you where the
main disconnect
is and which of the circuit break-
• Installation
Clearances
NEED
tools are needed
measure
The oven must be supplied with copper wires
ONLY.
local codes.
If installing your oven in Canada please
check to
make sure that you have a
model with the UL Canadian listing mark,
as shown below:
TOOLS
a 208 volt circuit must be used, wiring inside the
oven must be modified. See Connection
to a 208
Volt Circuit, in this manual. A circuit breaker or
time-delay
fuse sized not to exceed the circuit rating of the appliance specified on the rating plate
located on the frame behind the door of the oven
is recommended.
Oven
Single Oven
Double
Oven
and Wiring
required
• Electrical
Connections
Branch Circuit.
• Final Checklist.
Single
Required
for:
Requirements
if Connecting
for
3-wire
to 208
or
4-wire
TECHNICAL
SINGLE
DATA
OVEN
For cutout
dimensions
Preparing
Location
Single Oven
Models
see following
sections rifled:
Electrical Ratings
and Maximum Connected
Load
Convection
Oven
Volts
Hertz
Amperes
@240V/208V
Watts
@240V/208V
HBL 532A UC
240/208
60
13.5/13.6
3,250/2,820
No
HBL 535A UC
240/208
60
13.5/13.6
3,250/2,820
No
HBL 536A UC
2401208
60
13.5/13.6
3,250/2,820
No
I"IBL 542A UC
240/208
60
13.5/13.6
3,250/2,820
Yes
HBL 545A UC
240/208
60
13.5/13.6
3,250/2,820
Yes
HBL 546A UC
240/208
60
13.5/13.6
3,250/2,820
Yes
DOUBLE
OVEN
For cutout
dimensions
Preparing
Location
see following
sections
Electrical Ratings
and Maximum Connected
Double Oven
Models
Volts
titled:
Load
Watts
@240V/208V
Convection
Oven
(top/bottom)
Hertz
Amperes
@240V/208V
HBL 552A UC 240/208
60
27.1/27.1
6,500/5,640 Yes/No
HBL 555A UC 240/208
60
27.1/27.1
6,500/5,640 Yes/No
HBL 556A UC 240/208
60
27.1/27.1
6,50015,640 Yes/No
HBL 562A UC 240/208
60
27.1/27.1
6,50015,640
Yes/Yes
HBL 565A UC 240/208
60
27.1/27.1
6,500/5,640
Yes/Yes
HBL 566A UC 240/208
60
27.1/27.1
6,50015,640
Yes/Yes
f
4
UNDERCOUNTER
INSTALLATION,
i
SINGLE
Oven eleclflcaJsupply:.
Locate Ju_tion b_ in
adjacent cabinet or below
bottom support surface.
I
I
I
I
I
I
[
I
I <
28" opening width
)
I
I
I
I
I
I
I
I
I
I
Bottomsupport sul/eee must
be solid, level and able to
suppod at leest of 150 Ibs.
I
I
\
I
-------t
_
sp_
29-1/4" width of _n
1/4" rain. dlstance
between oven door
• frame and adjacent
doors or drawer fronts.
_na
door frame
maintain minimum spacing as shown.
Secure oven to cabinet using the screws
provided, Screws should be Inserted throl_h
the moun_ng holes in the positions indicated in
the frame (open door to see frame and
mounting holes). Do not overlJghtensctey_.
Note: DecoraUve inserts must
maintain minimum spacing as shown.
Refer
to and follow
Notes
and Warning
listed under Wall Installation,
Single
Oven
(facing
page)
5
WALL INSTALLATION,
SINGLE
OVEN
::_:
iSiK_to
_
to
_t
_the
Screws
i the mounti
ho4e_sIn
ktn_e frame
door to see frame and mounting
Do not overtighten screws.
Note:
Do not slide
,
oven
across
age to floor covering
suit.
floor.
Dam-
or floor could
re-
•
The oven support
surface must be a
minimum
3/4" thick plywood
platform, solid, level and flush with the
bottom of the cabinet cutout•
•
Use extreme caution when moving
installing the oven. it is very heavy.
or
4. Be very careful when moving or installing the oven to avoid damage to
the oven frame or damage to the cabinets.
•
Be sure
to level
oven.
not level may provide
sistent baking results.
6
An oven that is
poor
6. Be careful when placing oven. DO
NOT pinch the conduit between the
oven back or wall and the inner cabinet wall or floor.
or incon-
Securely
fasten
oven to cabinet
using the
screws provided• Failure to do so could result
in oven moving or tipping
during use and
causing damage to the oven or cabinets or personal injury•
WALL INSTALLATION,
DOUBLE
OVEN
Secure oven to cabinet using b_e
screws prided.
Screws should be
inserted through the mounting holes in
the positions indicated in the frame
(open door to see frame and mounting
holes). Do not overtighten screws.
Note:
Do not slide oven
.
age to floor covering
sult.
across
floor. Dam-
or floor could re-
The oven support surface must be a
minimum
3/4" thick
plywood
platform, solid, level and flush with the
bottom of the cabinet cutout.
.
.
Use extreme caution when moving
installing the oven. It is very heavy.
or
4. Be very careful when moving or installing the oven to avoid damage to
the Oven frame or damage to the cabinets.
,
6. Be careful when placing
oven. DO
NOT pinch the conduit
between
the
oven back or wall and the inner cabinet wall or floor.
Be sure to level oven. An oven that is
not level may provide poor or inconsistent baking results.
Securely
fasten
oven to cabinet
using the
screws provided. Failure to do so could result
in oven moving or tipping during
use and
causing damage to the oven or cabinets or personal injury.
ELECTRICAL
SUPPLY
WIRING
Before installing the oven have a qualified electrician verify that your home is provided with ade• quate electrical
service
and that the addition of
the oven will not overload
the branch circuit on
which it is to be installed.
A separate three-wire
or four-wire
single phase, 240 Volt, 60 Hz., or a
208 Volt, 60 Hz. branch circuit is required.
Note:
For use with 208 V, 60 Hz supply voltage
the wiring must be modified as shown in
Connecting to 208 Volt Circuit.
REQUIREMENTS
When making the wire connections, use the entire
length of the conduit provided (3 feet). The conduit must not be cut.
Before making connections make sure the power
is off and read and observe the following:
1.
A separate three-wire or four wire, single
phase, 240 Volt, 60 Hz. or 208 Volt, 60 Hz
branch circuit is required for the oven.
The oven must be connected
WIRE ONLY.
.
3.
with COPPER
In the United States:
For hook-up of the oven you will need to have an
approved junction box installed where it will be
easily reached through the.front of the cabinet
where the oven will be located. The oven has 3
feet of conduit. Allow two to three feet of slack in
the line so that the oven can be moved if servicing
is ever necessary. DO NOT shorten the flexible
conduit.
Wiring must conform to the National Electrical Code, ANSI/NFPA
No. 70 latest edition.
You can obtain a copy of the National Electrical Code by writing:
National Fire Protection
Association
Batterymarch
Park
Quincy, MA 02269
In Canada:
Wiring must conform to Canadian Electrical
Code C22.1- latest edition. You can obtain
ELECTRICAL
SHOCK
copies of the Canadian
writing:
HAZARD
are being
made.
an extension
cord
with this ap-
• If cold water pipe is interrupted
by plastic,
non-metallic
gaskets, union connections
or
other insulating
materials,
DO NOT use for
grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the NEUTRAL
or
GROUNDING
circuit. A fuse in the NEUTRAL or GROUNDING
circuit could result
in an electrical shock.
• Check with a qualified electrician
if you are
in doubt as to whether
the appliance
is
properly grounded.
Failure to follow these instructions
could result iF serious injury or death.
by
Wire size (COPPER WIRE ONLY) and connections must be suitable for the rating of the
appliance per the National Electrical" Code
requirements. The flexible armored cable extending from the oven should be connected
directly to the junction box.
.
• Electrical
ground is required on this appliance. The free end of the green wire (the
ground wire) must be connected
to a suitable ground.
This wire must remain
grounded
to the
oven.
Code
Canadian Standards Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario, Canada
M9W IR3
• The electrical power to the oven branch circuit must be shut off while line connections
• Do not use
pliance.
Electrical
The junction box should be located so as to
allow as much slack as possible between the
junction box and the oven so it can be moved
if servicing is ever required.
.
.
A U.L. listed conduit connector
must be provided at each end of the power supply cable.
CONNECTING
TO 208 V CIRCUIT
To connect
The ovens are pre-wired for connection to 240
volt, 60 Hertz supply. If connecting to a 208 volt,
60 Hz. supply a jumper must be used across two
terminals. For the double oven models there are
two jumpers, one for the upper oven and one for
the lower oven. For the single ovens there is one
jumper.
Please
jumper
refer to figures below for placement
for 208 volt, 60 hertz connection.
to 208 volt circuit:
Remove the access panel(s) located
back of the oven(s).
2.
Loosen the first and second screws in the terminal block as shown in applicable figure
above.
.
Place the metal jumper between the first
and second screws and tighten screws to
hold jumper in place.
of
4.
Replace
access panel(s).
Placing of jumper for single oven
or upper oven of double oven,
for connection to 208 volt, 60 Hz.
Before
Jumper
After
Jumper
Placing of jumper for lower oven
of double oven, for COnnectionto
208 volt, 60 Hz.
Before
Jumper
After
Jumper
on the
ELECTRICAL
This appliances
GROUND
wire
CONNECTIONS
3-WIRE
is manufactured
with a green
connected
to the oven chassis.
After making sure that the power has been turned
• off connect the flexible conduit from the oven to
the junction box using a U.L. listed conduit connector. Figures A and B and the instructions provided below present the most common
way of
connecting
the ovens. Your local codes and ordinances, of course, take precedence
to these instructions.
Complete
electrical
connections
according to local codes and ordinances.
Junction box
BRANCH
CIRCUIT
Refer to Figure A, where local codes allow the
connection
of GROUND wire from the cook-top
to the branch circuit NEUTRAL
wire (grey or
white colored wire):
• If local codes permit,
GROUND wire from the
wire from the oven to the
TRAL wire (grey or white
• Connect
connect the green
oven and the white
branch circuit NEUcolored wire).
the red and black leads from the cook-
top to the corresponding
box.
leads
in the junction
Cable from
_s_ply
Grounded Neutral
White
•
Figure
4-WIRE
BRANCH
Refer to Figure
it connector
A.
• Connect the red and black leads from the oven
to the corresponding leads in the junction box.
CIRCUIT
B:
• Connect the green GROUND
wire from the
oven to the GROUND
wire in the junction box
(bare or green colored wire).
• Connect the white wire from the oven to the
NEUTRAL
(grey or white) wire in the junction
box.
Ungrounded
Cable
fromo_n
Figure
10
.
B.
Neutral
FINAL
CHECK
LIST
volt the voltage reading between the black
and red wires should be 190 to 208 volts.
To prevent improper connections
leading to damage of electrical
components
and so voiding the
warranty, the following steps must be performed:
5.
Set the time of day by pressing
the Set
Clock button and pressing the plus (+) or minus (-) button, to the right of the display to
set the correct time. Once the time is set depress the Set Clock button to enter the time.
A "beep" will sound and the Set Clock symbol in the upper right will disappear.
6.
Turn the Mode Selector knob to Manual position, the Selector knob to Bake and turn the
Check the electrical
requirements
and make
sure you have the correct electrical
supply
and that the oven is properly grounded.
.
Make sure all control knobs are in the off position.
.
Temperature
knob to 350 *F. The cooling
fan, the oven lights and the Preheat light
should come on to indicate that the oven is
Turn on the power supply to the oven. When
the oven is first turned on the display will
come on showing all the call-outs and then
will become blank with the Set Clock symbol in the upper right comer, as shown below.
,
SETG
heating. The Preheat light will turn off when
the set temperature
(350 OF) is reached. Turn
Temperature
knob to off. If you have installed a double oven repeat test for second
oven.
7.
To check
the other
oven
functions
the Using the Oven Controls
Use and Care Manual.
I
.
.
Check power at the junction box wires using
a volt meter having a range of 0-250 VAC. If
you have installed
the oven for use on 240
volt supply you should find that the voltage
reading
between
the black and red wires
(Line to Line) should be 220 to 240 volts. If
you have modified the oven(s) for use on 208
section
refer
to
of the
If the oven is working properly turn the Selector knob(s)
and the Temperature
Control
knob(s) to their off positions and press in the
knobs so that they are flush with the oven
and turn off the power supply to the oven.
9.
Place the cover on the junction
box
make sure the cover is securely fastened
turn on the power to the oven.
and
and
10.
Leave
these INSTALLATION
instructions
as well as the USE AND CARE MANUAL
with the owner.
II