Canon 450D - EOS Rebel XSi Instruction manual

06150
UNDERWATER HOUSING for
Canon EOS Kiss X2 / REBEL XSi / 450D
Canon EOS Kiss X3 / REBEL T1i / 500D
日本語
RDX-500D
English
取扱説明書
Instruction Manual
Introduction
Thank you for purchasing SEA&SEA products.
Please read this instruction manual carefully prior to using this product.
Only with a thorough understanding of this manual’s content will you
be able to use the housing correctly. After reading the manual, please
be sure to keep it in a place where you can easily come back to it at
any time.
Note:
Pressure-resistance inspection sticker
Products bearing this sticker are those that have passed SEA&SEA’s
criteria-based inspection for pressure resistance.
Contents
Safety Precautions ......................................................................... E-2
Precautions on Handling the O-ring ............................................... E-4
Identification of Parts ..................................................................... E-6
Pressure balance control valve ................................................ E-7
Finder ....................................................................................... E-8
Preparation for Setting Up ............................................................. E-9
Prepare the housing and port ................................................... E-9
Prepare the digital camera ....................................................... E-9
Prepare the connecting accessories ........................................ E-9
Opening and Closing the Housing ............................................... E-10
Attaching and Detaching the Port ................................................ E-11
Mounting the Camera in the Housing .......................................... E-13
When using the fiber-optic cable ............................................ E-13
When using the YS converter ................................................ E-16
Connecting the Strobe ................................................................. E-18
With the fiber-optic cable ...................................................... E-18
With the YS converter ........................................................... E-19
Attaching the Hand Strap ............................................................. E-21
External Controls .......................................................................... E-22
Attaching the Optional Accessories .............................................. E-24
Maintenance and Storage .............................................................E-26
Specifications ................................................................................E-27
E-1
Safety Precautions
For safe handling of the product, please read the following precautions
carefully before use.
Failure to heed the precautions listed below could result in serious
consequences. To prevent injury or damage to yourself and/or others,
please observe the precautions as they contain highly important
information related to personal and product safety.
WARNING
Situations that could result in severe injury or death.
CAUTION
Situations that could result in property damage or
personal injury.
WARNING
=Keep out of reach of children to prevent accidental ingestion. If swallowed, seek
medical advice immediately.
CAUTION
=Carefully observe the instruction manual for the compatible camera for this product
before use.
=This product must be used in combination with the optional port for SEA&SEA digital
SLR camera housings. This product cannot be used alone.
=This product has been designed and manufactured for use at a water depth within
60m / 200ft. Please note that diving to a depth in excess of 60m / 200ft may cause
damage to the product or may lead to water leakage.
=Unauthorized disassembling and/or modification could result in malfunction or flooding,
and void product warranty. Take the product to a SEA&SEA authorized service center
for repair or inspection.
=Should you notice smoke or an unusual smell coming from the product, turn it off and
remove the batteries immediately, taking care to avoid burns. Continued operation
could result in injury. After removing the battery, take the product to a SEA&SEA
authorized service center for inspection.
=Discontinue use and turn the product off immediately should you notice flooding or
leakage.
=When the product is flooding, interior pressure may build up. Please be careful when
opening the product as water may spurt out or the cap may open explosively and cause
injuries.
=The product has been constructed with an airtight seal. When packing the product
for airplane travel, do not seal-up the product to alleviate pressure build up due to
atmospheric changes.
=Do not open the product in a wet or sandy environment. Protect the interior from
moisture and debris in order to prevent malfunction or flooding.
=Avoid strong shocks/impacts or excess stress to prevent malfunction, damage or
breakdown. Make sure that the product has been securely mounted to other products
in order to prevent injury, fall or missing.
E-2
Safety Precautions
=Do not rest heavy weight on the product. It might deform the outer casing, damage
internal parts, make the waterproofing fail, or result in fire or electric shock.
=Please note that some marks may be left on the camera scraping against the dials
or gears of the housing.
=Handle the product carefully so as not to scratch the front port, the lens, the flash
window or the finder.
=Always dry the front port, the lens, the flash window or the finder using a soft cloth to
prevent stain or salt residue from marring the glass surface.
=Rinse the product with fresh water, after underwater use. Ensure that the product is
waterproofed before rinsing. Refer to [Maintenance and Storage] (P.E-26) for details.
=Make sure that the connectors have been secured with the connector caps before
rinsing the product with fresh water, after removal from other products.
=Never use chemicals, cosmetics, any petroleum solvents such as paint thinner, or
neutral detergent on the product. They may deform and damage the product.
=Do not leave the product in places with hot temperatures such as inside of a car or in
a car trunk in summer. The heat may deform plastic parts of the product, damaging
internal parts and resulting in potential fire or electric shock. If the product is sealed
tight in hot conditions, heated air expanding inside the product may deform the casing
and ruin the waterproofing.
=Do not store the product in wet or high humidity place, to avoid mold, rust, corrosion
or malfunction.
=Do not store the product with naphthalene or camphor mothballs, or in locations such
as a laboratory where chemicals are used. This environment can cause mold, rust,
corrosion or malfunction.
=SEA&SEA SUNPAK Co., Ltd. assumes no liability for compensation of loss of
captured images or expenses caused by loss of images, even if you are unable to
shoot due to a product defect or malfunction.
=SEA&SEA SUNPAK Co., Ltd. will not be responsible for the replacement or
compensation for cameras, lenses or those accessories damaged due to your
invalid operation.
=SEA&SEA SUNPAK Co., Ltd. assumes no liability for errors or discrepancies in
this manual.
=Carefully observe the O-ring maintenance manual for the handling of O-rings
before use.
=The silicon grease included in the product package is inedible.
E-3
Precautions on Handling the O-ring
This product is kept watertight by the O-ring. To keep the O-ring functioning
properly, please observe the following. Improper handling of the O-ring could
cause flooding.
CAUTION
=SEA&SEA products use blue O-rings. These O-rings are impregnated with
silicone oil through a special process. The lubricating effect of the O-ring lasts
as long as the silicone oil is gradually seeping out from within.
=For the maintenance of these blue O-rings, make sure to use genuine SEA&SEA
silicone grease (O-ring grease for use with the blue O-rings that comes in tubes
with blue lettering and blue caps). If you use silicone grease from other companies
or SEA&SEA’s own silicone grease that comes in tubes with black lettering and
black caps, the grease you apply will be sucked into the blue O-rings due to
their special characteristics, which will result in insufficient grease. If this happens
even once, the O-ring will not revert to its normal state and must be replaced.
=If the grease is insufficient, the O-ring will not slide, and it will become harder
to open and close the waterproof parts. Because of this, it could become
impossible to open or close the housing or it could cause flooding, so please
refrain from using the housing with insufficient grease.
Are there any scratches or cracks in the O-ring?
Check the O-ring to make sure there are no
scratches or cracks. If there are, replace the
O-ring with a new one immediately. When
handling the O-ring, do not use pointed
metal objects, which could damage the
O-ring. Use of the included O-ring remover
is recommended.
O-ring remover
Be careful about dust, sand, and hair
Check the O-ring to make sure that there is no dust, sand, or hair on the O-ring,
in the O-ring’s grooves, or on the O-ring’s contact surfaces. If any of these things
are attached, remove them completely. If used as is, these things could cause
flooding.
E-4
Precautions on Handling the O-ring
Coat with silicone grease
Silicone grease protects the O-ring from
chafing. After checking the O-ring to make
sure that there are no scratches, dust, or
debris, apply a light coating of silicone grease
to the entire O-ring with your finger. Applying
too much grease will make it easier for dust
and debris to adhere to the O-ring, and could
cause flooding.
Do not twist the O-ring
When fitting the O-ring into the O-ring
groove, insert it straight into the groove; do
not bend or twist it.
Remove the O-ring for inspection before each use
In principle, the O-ring should be removed before each use so that the O-ring,
O-ring groove, and O-ring contact surfaces can be checked. This is because you
cannot find any sand or debris that may have gotten into the O-ring groove if the
O-ring is not removed. For routine maintenance prior to each use, it is advisable
to make sure to remove the O-ring.
Be careful about how you store O-rings
When storing spare O-rings or O-rings that you have removed from the housing,
keep them in a cool place out of direct sunlight. Also, when storing O-rings, do
not place heavy objects on them or twist them.
O-rings last for one year
Although it depends on how well they are maintained, how often they are used,
and how they are stored, O-rings generally last for one year. It is advisable to
inspect them before use, and replace them early.
E-5
Identification of Parts
Power switch
Accessory shoe
Fiber-optic cable socket
ISO speed set button
Main dial
Focus / Zoom dial
Shutter lever
Buckle
Buckle lock lever
Port mount ring
Hand strap eyelet
Front case
Pressure balance control valve
Viewfinder
L-hook
YS converter
connector
Buckle lock
lever
Buckle
Rear case
Menu button
DISP.button
Tripod socket (bottom)
Port lock
Aperture / Exposure
compensation button
Mode dial
AE lock / FE lock / Index /
Reduce button
AF point selection /
Magnify button
Hand strap eyelet
WB selection button (*1)
AF mode selection
button
Setting button
Erase button
Picture Style selection
button
Playback button
Drive mode selection button
Live View shooting / Movie
shooting Share button (*2)
*1: It controls the Metering mode button of the EOS 450D/Rebel XSi camera.
*2: It controls the WB selection button of the EOS 450D/Rebel XSi camera.
E-6
Identification of Parts
Sync connector
Front case
Camera tray
Fixing screw
Camera base
Knob
Sync connector
bracket
Pressure balance control valve
This product comes equipped with a pressure balance control valve.
Pushing the valve counterbalances the pressure difference that occurs
due to temperature or atmospheric changes, and makes it possible to
open the housing.
How to use
Push the pressure balance control
valve using a stick or other thin
object.
CAUTION
=The product has been constructed
with an airtight seal. When packing
the product for airplane travel, do
not seal-up the product to alleviate
pressure build up due to atmospheric
changes.
E-7
PUSH
Identification of Parts
Finder
This product comes equipped with a 0.5x pick-up finder. The finder can
be replaced with an optional finder unit so you can change the finder
magnification to match your shooting conditions.
Replacing the finder
1
Rotate the finder unit mounted on
the rear case in a counterclockwise
direction to remove it
=The screw areas are coated in
grease, so be careful not to touch
them.
2
Rotate the replacement finder
unit in a clockwise direction to
attach it
CAUTION
=Before attaching the finder, check to make sure that there is no dust, dirt,
or debris inside it.
=When replacing the finder, do not touch the surface of the finder lens.
=When replacing the finder, always refer to the instruction manual provided.
E-8
Preparation for Setting Up
This product must be used in combination with the optional equipment
(digital camera, port, strobe, accessories etc.) for underwater photography.
In order to set up the equipment, prepare each item correctly.
Prepare the housing and port
Maintaining the O-ring
This product is kept watertight by the O-ring.
To keep the O-ring functioning properly,
please observe the following before setting up.
O-ring
=Make sure to remove the O-ring when maintaining.
=For detailed O-ring maintenance methods,
please see the O-ring maintenance manual.
CAUTION
=Make sure to fit/install the O-ring into the groove properly after maintenance.
Prepare the digital camera
This product is exclusively designed for use with Canon EOS REBEL
XSi / 450D or REBEL T1i / 500D digital camera. Other cameras are not
compatible with this product.
=Make sure that there is sufficient battery power remaining and the image
storage medium has enough room for the number of pictures.
=Remove the eyecup from the camera.
=Remove the strap or the LCD monitor cover from the camera, if any of
these accessories are attached.
=If the lens has a focus mode switch, set it properly.
=Make sure the camera is operating correctly, referring to the camera's
instruction manual for details.
Prepare the connecting accessories
When using external strobes, lights or other accessories in combination
with this product, prepare the equipment before setting up.
=If the accessories are kept watertight by O-rings, make sure the O-rings
are properly maintained.
=If the accessories are powered by batteries, make sure that there is sufficient
battery power remaining.
=Make sure the equipment is operating correctly, referring to the instruction
manual provided with the equipment.
E-9
Opening and Closing the Housing
Opening and closing the housing is done with the buckles. Here we will
explain how to open and close the buckles.
Opening the buckle
1
Press and hold the buckle lock lever
(①), and remove the right and left
buckles simultaneously (②)
CAUTION
=When removing the buckle, be sure to use
the tips of your fingers, not your fingernails.
2
Remove the L-hook from the front case
Buckle lock lever
Closing the buckle
2
3
Attach the L-hook to the front case
L-hook
Attach the buckles to the rear
case (①), and close the right and
left buckles simultaneously (②)
CAUTION
=Before aligning the rear case and front case, make sure there are no specks
of dust, scratches, or deformities on the O-ring and the O-ring contact
surfaces.
=Check to make sure that the buckles are securely locked.
E-10
Attaching and Detaching the Port
In order to use this product underwater, the optional port for the camera
lens must be attached to this product.
CAUTION
=Only the optional ports designed for SEA&SEA RDX-series housings can
be attached to this product.
=This product is delivered with a housing body cap attached to the port mount.
Make sure to remove the housing body cap when attaching the port.
=The housing body cap has no watertight capability.
=When attaching the port to the housing, always refer to the instruction
manual provided.
Attaching the port
1
2
Release the port lock on the
RDX housing (front case) by
sliding it in the direction of
the arrow as shown in the
diagram, and rotate the port
mount ring toward OPEN (in
a counterclockwise direction)
until it stops
Align the convex part of the
Port with the concave part of
the port mount ring, and fully
insert the port into the housing
LOCK
OPEN
Slide
Port lock
Convex part
Convex part
Concave
part
CAUTION
Concave part
=Before attaching the port, make sure there are no specks of dust, scratches,
or deformities on the O-ring and the O-ring contact surfaces.
E-11
Attaching and Detaching the Port
3
Rotate the port mount ring toward
LOCK (in a clockwise direction)
until you hear it click into position
=Make sure that the
port lock has returned
to the lock position as
shown in the diagram.
LOCK
OPEN
Lock position
Click
Detaching the port
1
2
Release the port lock by sliding it in the direction of the arrow, and
rotate the port mount ring toward OPEN (in a counterclockwise
direction) until it stops
Hold the RDX housing (front case) firmly, and pull the port
straight off
CAUTION
=Do not attempt to detach the port with the port mount ring locked. This
could result in damage to the port mount ring.
=If using NX-90PRO ports (with 4-digit part numbers and black bayonets)
with this product in combination with the RDX Port Base L, it is necessary
to modify the port's bayonet. NX-90PRO ports with 5-digit part numbers
and gray bayonets can be used as is. For details, please contact SEA&SEA
or a SEA&SEA authorized dealer.
E-12
Mounting the Camera in the Housing
CAUTION
=Make sure to remove the eyecup from
the camera. If used with the eyecup in
place, it could cause flooding.
=If the display-off sensor is activated,
the LCD monitor of the camera will
turn off automatically when the camera is mounted in the housing and
the rear case is closed.
When using the fiber-optic cable (option)
1
Release the lock on the camera
tray by pushing the knob in the
direction of the arrow (①), and
slide the camera tray out (②)
Knob
2
3
4
Attach the camera tray to the
camera's tripod socket by
fastening the fixing screw
using the supplied attachment
tool
Attach the lens to the camera
Place the sync connector in the
sync connector bracket inside
the front case
=This product is shipped from the factory
with the sync connector placed in the
bracket.
E-13
Attachment tool
Fixing screw
Mounting the Camera in the Housing
5
6
7
8
Pull the power switch and
focus/zoom dial out
Pop up the camera's built-in
flash. Align the camera tray
with the camera base inside the
front case, and slide the camera
forward into the front case
=Make sure to pop up the built-in flash
of the camera before mounting the
camera in the housing. Once the
camera has been mounted, the flash
button of the camera cannot be used,
and the camera's built-in flash cannot
be popped up.
=Make sure the camera tray is inserted
all the way into the camera base until
it stops.
=Make sure that the camera tray is
properly placed and the knob is
locked.
Lever
Align the lever of the housing's
power switch and the camera's
power switch
Power switch
Place the rear case on the front
case, and close the buckles
See:
“Opening and Closing the Housing” (P. E-10)
=Make sure that the O-ring is properly fitted in the O-ring groove before
setting of the rear case.
CAUTION
=After the camera is mounted in the housing, make sure to check that all of
the housing's control parts work properly and the camera functions correctly.
E-14
Mounting the Camera in the Housing
Removing the camera from the housing
1
2
3
4
Open the buckles
Remove the rear case
Pull the power switch and focus/zoom dial out
Release the lock on the camera tray by pushing the knob, and
slide the camera tray out
E-15
Mounting the camera in the Housing
When using the YS converter (option)
1
2
3
4
5
Release the lock on the camera
tray by pushing the knob in the
direction of the arrow (①), and
slide the camera tray out (②)
Knob
Attach the camera tray to the
camera's tripod socket by
fastening the fixing screw
using the supplied attachment
tool
Attach the lens to the camera
Attachment tool
Fixing screw
Pull the power switch and
focus/zoom dial out
Align the camera tray with the
camera base inside the front
case, and slide the camera
forward into the front case
=Remove the sync connector from the
bracket, and move the sync connector
clear of the front case.
=Do not pop up the camera's built-in
flash.
=Make sure the camera tray is inserted
all the way into the camera base until
it stops.
=Make sure that the camera tray is
properly placed and the knob is
locked.
E-16
Mounting the Camera in the Housing
6
Insert the sync connector into
the camera's accessory shoe
CAUTION
When inserting or removing the sync
connector, be sure to hold the connector
part. If you push or pull on the cord part,
it could damage the sync connector or
cause contact failures.
7
8
Align the lever of the housing's
power switch and the camera's
power switch
Lever
Power switch
Place the rear case on the front
case, and close the buckles
See:
“Opening and Closing the Housing” (P. E-10)
=Make sure that the O-ring is properly fitted in the O-ring groove before
setting of the rear case.
CAUTION
=After the camera is mounted in the housing, make sure to check that all of
the housing's control parts work properly and the camera functions correctly.
Removing the camera from the housing
1
2
3
4
5
Open the buckles
Remove the rear case
Remove the sync connector from the camera's accessory shoe
Pull the power switch and focus/zoom dial out
Release the lock on the camera tray by pushing the knob, and
slide the camera tray out
E-17
Connecting the Strobe
This product comes equipped with two fiber-optic cable sockets and a
YS converter connector.
With the fiber-optic cable (option)
Connect the strobe with the fiber-optic cable (option) when the strobe is
triggered by sensing the light from the camera's built-in flash.
1
2
Remove the fiber-optic cable
socket caps
Fiber-optic cable socket cap
Insert the fiber-optic cable's
connector into the socket until
it stops
=Do not remove the caps from fiberoptic cable sockets not in use to keep
light from entering in.
CAUTION
=There is no possibility of water leaking from the fiber-optic cable socket
even if the fiber-optic cable/cable socket cap is removed underwater.
=After the strobe is connected to the housing, make sure to check that
the connected strobe functions correctly before underwater use.
E-18
Connecting the Strobe
With the YS converter (option)
Connect the strobe with the YS converter (option) when the strobe is
triggered in conjunction with the camera.
CAUTION
=Carefully observe the instruction manual for the YS converter before use.
=A Grip-stay L (option) is required when using the YS converter.
=Do not connect the strobe and the YS converter connector with a sync cord
(option) because this will damage the YS converter connector.
1
2
3
Remove the connector cap from the YS converter connector
Make sure there are no scratches
or debris on the O-ring of the
connecting cable being connected
Align the round mark (or the notch
on the tip) of the connecting cable
with the round mark (or the convex
part inside) of the strobe bulkhead,
and then push it straight in
E-19
YS converter connector
Connecting cable
Connecting the Strobe
4
Align the B part of the connecting
cable with the screws of the strobe
bulkhead, and then rotate it until
it stops
C B A
=Do not twist the A (cable) part.
5
Rotate the C part of the connecting
cable until it stops
=Tighten it securely.
=When removing the connecting cable,
loosen C first, then B, and then pull the
connecting cable straight out holding
onto A. Do not pull on the cable part.
CAUTION
=After use underwater, make sure to prevent water droplets from dripping
into the bulkhead connector by wiping moisture away from the bulkhead
connector and then turning the housing upside down and extracting the
sync cord. In the event that water droplets do drip into the connector,
promptly wipe away all moisture.
=If you use incompatible strobes, not only might they not work correctly,
but they may also cause the camera and the strobe to malfunction.
=If not connecting the YS converter, do not remove the connector cap from
the YS converter connector. Make sure the cap is firmly secured to avoid
water leakage due to a loose cap.
=After the equipment is connected to the housing, make sure to check that
the connected strobe and YS converter function correctly before underwater
use.
E-20
Attaching the Hand Strap
1
Put the hand strap through the
hand strap eyelet on top of the
housing as shown
③
②
④
①
2
Put the hand strap through the
hand strap eyelet on bottom of
the housing as shown
=Ensure a good grip, then fasten the
velcro.
=Make sure to attach at least 2/3 of
the velcro's length.
=Hold the equipment by the housing
body when carrying it. Carrying the
equipment by holding the strap may
cause it to fall and being damaged.
④
②
③
①
How to use the Hand Strap
Pass your right hand between the
hand strap and the housing, then
hold onto the housing body while
grasping the buckle part.
=When shooting, support the bottom part
of the housing/port with your left hand,
and hold the housing firmly with both
hands.
CAUTION
=Be careful not to touch the glass surface of the port glass with your
left hand (fingers).
E-21
External Controls
Power switch
Power switch
By rotating the knob as indicated, you can
turn the power ON/OFF.
Shutter lever
Shutter lever
Push the lever toward you or gently press on
it from the top to control the shutter button
of the camera.
Focus / Zoom dial
When a focus or zoom gear is mounted on
the lens, you can control the manual focus
or adjust the zoom angle.
Focus / Zoom dial
CAUTION
=The focus / zoom dial cannot be used
if there is no gear mounted on the lens.
=When using a zoom gear, you cannot
shoot with manual focus.
=Do not use a focus gear when you wish
to shoot with autofocus. Autofocus
shooting with a focus gear will damage
the lens.
Aperture / Exposure compensation button
While pressing the button, rotate the main
dial to make operation settings. By rotating
the button while pressing it in, you can fix it
in the pressed-in state.
Aperture / Exposure
compensation button
E-22
External Controls
WB selection button
It controls the Metering mode button of the EOS 450D/Rebel XSi camera.
Live View shooting / Movie shooting button
It controls the WB selection button of the EOS 450D/Rebel XSi camera.
Other controls
Other control parts on the housing correspond to the operation parts of the
digital camera. Refer to the camera's instruction manual for details of each
function.
CAUTION
=After mounting the camera in the housing, make sure to check that all of
the housing's control parts work properly and the camera functions correctly
before underwater use.
E-23
Attaching the Optional Accessories
This product accepts SEA&SEA optional accessories. By using this
product in combination with those accessories, you will be able to try
various shooting techniques.
CAUTION
=Strobes and other accessories may have different depth rating.
Check the depth rating for each before use.
=Read the instruction manual for each accessory before use.
Accessory shoe
SEA&SEA strobes / lights can be
mounted to the accessory shoe by
using optional Mini Shoe Arm
(#29511) or Hot Shoe Arm
(#29501).
<Example>
CAUTION
=The max. weight of an accessory that can be mounted to the accessory shoe
is approx. 750g / 26.3oz (equivalent to the weight of SEA&SEA YS-110α
strobe).
=Remove the accessories from the accessory shoe when carrying the housing
out of water.
E-24
Attaching the Optional Accessories
Stays / Arms
SEA&SEA stays / arms can be mounted to the housing's tripod socket.
<Example>
Grip-stay L
Sea Arm VII
E-25
Maintenance and Storage
CAUTION
=Never use chemicals, cosmetics, any petroleum solvents such as paint thinner,
or neutral detergent on the product. They may deform and damage the product.
=After each use in salt water, make
sure it’s watertight, then soak it
sufficiently in fresh water.
=Insufficient soaking causes damage
by salt to the product. Salty residue
may be left on the product where it will
crystallize as it evaporates. Crystallized
salt is hard to dissolve and difficult to be
removed once formed, and it will result in
water leakage.
=After rinsing, dry the product well with a soft dry cloth, then let the product dry
in the shade, out of direct sunlight.
=Do not dry the product by heating (using a hair dryer, for example). Heating can
deform and damage the product.
=If you will not use the product for an extended period of time, store it away from
high temperatures, high humidity, direct sunlight, or extreme cold.
=Do not store the product with naphthalene or camphor mothballs, or in locations
such as a laboratory where chemicals are used. This environment can cause
mold, rust, corrosion or malfunction.
=Always remove the camera from the housing after use. Thoroughly wipe off water
before opening the housing and avoid any water drops inside the housing.
=After using the product, maintain the O-rings before storing. Examine the O-rings
before and after each dive. We recommend early exchange of the O-rings, at
least once a year.
=Every two years we recommend a complete overhaul of O-rings regardless of
the frequency in use, for the best performance of the product.
E-26
Specifications
Compatible
camera
Canon EOS REBEL XSi / EOS 450D
Canon EOS REBEL T1i / EOS 500D
Controls
Power switch, ISO speed set button, Main dial, Shutter
button, Mode dial, AE lock / FE lock / Index / Reduce
button, AF point selection / Magnify button, Aperture /
Exposure compensation button, WB selection button(* 1),
Live View shooting / Movie shooting button(* 2), AF mode
selection button, Setting button, Erase button, Picture
Style selection button, Playback button, Drive mode
selection button, DISP. button, MENU button
Construction
Body: Polycarbonate resin (Black)
Depth rating
60 m (200 feet)
Dimensions
Approx. 200 (W) × 190 (H) × 139.5 (D) mm
(14.2× 8.8 × 6.0 inches)
Weight
Approx. 2000 g (4.4 lbs.) (housing only)
Accessories
Silicone grease, Attachment tool, O-ring maintenance
manual, Hand strap, Instruction manual (this manual),
Attached accessories to the product : Housing body
cap, Fiber-optic cable socket cap (x2), YS converter
connector cap
The specifications and appearance are subject to change without notice.
*1: It controls the Metering mode button of the EOS 450D/Rebel XSi camera.
*2: It controls the WB selection button of the EOS 450D/Rebel XSi camera.
E-27
シーアンドシー・サンパック株式会社
〒332-0016 埼玉県川口市幸町3-2-20
TEL.048-256-2251
カスタマーサービスセンター
TEL.048-255-8512
http://www.seaandsea.co.jp
SEA&SEA SUNPAK Co., Ltd.
3-2-20, Saiwai-cho, Kawaguchi-shi,
Saitama, Japan 332-0016
TEL. +81-48-256-2251
World Customer Service Center
TEL. +81-48-255-8512
http://www.seaandsea.jp