- Home
- Domestic appliances
- Large home appliances
- Tumble dryers
- Whirlpool
- SDRY60CE
- Operating instructions
advertisement
OPERATION MANUAL
SENSOR TUMBLE DRYER
Model:SDRY60CE
Start
(Pause)
Drying Times
(mins)
90
75
60
40
30
20
10
Off
Airing
Extra Dry
Normal Dry
Iron Dry
Cottons
Extra Dry
Normal Dry Synthetics
Iron Dry
Delicate Plus
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
TABLE OF CONTENTS
BEFORE USING THE DRYER PLEASE READ THE
INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
IDENTIFICATION OF PARTS
INSTALLATION INSTRUCTIONS
INVERTED WALL MOUNTING
STACKING INSTALLATION
FRONT VENTING
REAR VENTING
INSTALL THE FLEXIBLE HOSE
OPERATING INSTRUCTIONS
CONTROL PANEL
OPERATING INSTRUCTIONS
CLEANING AND MAINTENANCE
TROUBLESHOOTING AND SPECIFICATIONS
WIRING CIRCUIT
SPECIFICATIONS
TROUBLESHOOTING GUIDE
16
16
17
1
11
11
14
5
7
3
4
9
9
10
IMPORTANT SAFETY INSTRUCTIONS
Warning - To reduce the risk of fire, electric shock, or personal injuries, the following basic precautions should be followed:
1 Read all instructions before using this dryer.
2 The interior of the dryer should be cleaned periodically by qualified service
personnel. An excessive amount of lint build up in the interior of the dryer could
result in inefficient drying and pose a possible fire hazard.
3 The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer in such a way that a full opening of the tumble dryer is restricted.
4 Attention - rear panel can be hot.
5 The tumble dryer should not be used if industrial chemicals have been used to
clean the dryer.
6 The dryer must only be used for its intended purpose.
7 Clean lint screen before or after each load.
8 This appliance is not intended for use by people (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Young children should be
supervised to ensure that they do not play with the appliance.
9 Do not operate the dryer if any parts are missing or broken.
10 To avoid fire hazard or electrical shock do not use an adaptor plug or extension
cord or remove grounding prong from electrical power cord. Failure to follow this
warning can cause serious injury, fire or death.
11 To avoid fire hazard or electrical shock do not reach into the drum while the drum is moving. Wait until the dryer has stopped completely before reaching into the drum.
12 Do not attempt to modify or repair the controls.
13 The final part of a tumble dryer cycle occurs without heat (cool down cycle) to cool
items to a temperature that ensures that they will not be damaged. Never stop a
tumble dryer before the end of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.
14 Do not dry items that have been previously cleaned in, washed in, soaked in, or
spotted with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine,waxes and wax removers, etc. Do not store or use these items
on or in the vicinity of the dryer. Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may contribute to a chemical reaction that
could cause a load to catch fire. Oil-affected items can ignite spontaneously, especially
when exposed to heat sources such as in a tumble dryer. The items become warm,
causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fire. Piling, stacking or storing
oil-affected items can prevent heat from escaping and create a fire hazard. If it is
unavoidable that fabrics that contain vegetable or cooking oil or have been
1
IMPORTANT SAFETY INSTRUCTIONS
contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent - this will reduce, but not eliminate, the
hazard.
15 Do not dry unwashed items in the tumble dryer.
16 Fabric softeners, or similar products, should be used as specified by the fabric
softener instructions.
17 To To prevent fire, do not use heat to dry items containing plastic, foam rubber or
similarly textured rubber-like materials, or items containing feathers or down. Items
such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed
articles and clothes or pillows fitted with foam rubber pads should not be dried in the
tumble dryer.
18 This dryer must be properly installed in accordance with the installation instructions before it is used.
19 Do not install or store this dryer where it will be exposed to water and /or the weather. Keep surrounding areas free from the accumulation of lint, dust and dirt.
20 To prevent shock hazard and assure stability during operation, the dryer must be
installed and electrically grounded by a qualified service person in accordance with
local codes.
21 Do not sit on top of the dryer.
22 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
23 Always disconnect dryer from electrical supply before attempting any service.
24 Disconnect power cord by grasping the plug, not the cord. Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in the user-maintenance instructions.
25 Before the dryer is removed from service or discarded, remove the dryer door to
prevent accidental entrapment.
26 Remove all objects from pockets such as lighters and matches.
Caution, risk of fire - this is a safety symbol. Failure to follow the warnings outlined in these user instructions can cause a fire hazard.
2
Control panel
Service label
Door airproof strip
Door
Lint filter
Power supply cord
IDENTIFICATION OF PARTS
Drying Times
(mins)
90
75
60
40
30
20
10
Off
Airing
Extra Dry
Normal Dry
Iron Dry
Cottons
Extra Dry
Normal Dry
Synthetics
Iron Dry
Delicate Plus
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
Top panel
Program selector
Door switch
Door latch
Exhaust grill
Model number and Serial number
Back plate
Air intake grill
Outlet cover
Warning
Read all instructions before using this dryer.
This dryer has been designed for domestic use only.
SAVE THESE INSTRUCTIONS.
This diagram may be slightly different from the layout of the dryer you have just purchased due to technical improvements.
3
INSTALLATION INSTRUCTIONS
Unpacking your dryer
Dimensions a=830 mm b=600 mm c=560 mm
Weight=30 kg
Remove the transport packaging (f ig.1)
Remove the tape on the door (fig.2), the wall mounting kit and the inverted panel
film attached to the inside of the drum (fig.3) before starting the dryer. fig.1
fig.2
fig.3
Packing accessories
Check list of the accessories and materials provided with the machine:
Name
User manual 1
Wall mounting kit 1
Inverted panel film 1
Flexible hose 1
Quantity
Flexible hose clip 1
Hose connector 1
Stacking kit 2
Warranty card 1
To ensure the dryer operates normally, attention must be paid to the following:
1. The rear of the dryer must not have any restriction to the intake of fresh air.
2. Check the dryer for any damage. If any damage is found do not operate
and contact your supplier or Whirlpool Customer Service.
3. The dryer must be kept away from flammable substances.
4. The surrounding environment must be dry and ventilated.
5. For best results, the ambient temperature should be between 10 and 35 .
4
INSTALLATION INSTRUCTIONS
Free standing
The dryer stands on the floor and can easily be moved into position. Ensure that it is placed on a level floor. Also ensure there is at least 50 mm air clearance between the back of the dryer and the wall to allow fresh air flow for efficient operation even using the front venting option.
Start
(Pause)
Drying Times
(mins)
90
75
60
40
30
20
10
Off
Airing
Extra Dry
Normal Dry
Iron Dry
Extra Dry
Cottons
Normal Dry Synthetics
Iron Dry
Delicate Plus
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
Attention:
Please don’t put a heavy load on the dryer’s top panel, such as a basketry full of
wet laundry.
Start
(Pause)
Drying Times
(mins)
30
20
10
90
75
60
40
Off
Airing
Extra Dry
Normal Dry
Cottons
Iron Dry
Extra Dry
Normal Dry
Iron Dry
Delicate Plus
Synthetics
Delay
Time Remaining
MIN
SDRY60CE
Sensor Dryer
6kg
Inverted wall mounting
The dryer can be mounted on the wall in the inverted position only by following these instructions.
Invert the dryer so that the control panel is at the bottom (see figure 4) this allows easier access to the controls.
1. Determine the location of the dryer on the wall and mark the bracket
position.
A minimum 50 mm is needed between the top of the dryer and the ceiling
for ease of installation;
If mounting above a washing machine, allow sufficient room to open the lid
of the washer.
Tools required
For plaster/ Drill & 3mm Bit
Wooden wall Philips head screwdriver
1
1
Wall mounting kit includes
Description
Plastic spacers 2
Wall hanging brackets 2
Hanging hook 2
Wood screws, 12gx50mm 4
Screws for hanging hooks 6 and plastic spacers.
Minimum lid
clearance
5
INSTALLATION INSTRUCTIONS
2.Fix the wall hanging brackets to the wall securely (eg. into the stud).
If the studs are too far apart, fit a timber slat to the studs then mount the
brackets onto the slat. The distance between each is 553 mm as per
diagram (Fig.1).
Fig.1
553 mm
Wood screw
Warning: Ensure that the screw and nut of the Wall Hanging Brackets are
tightened during installation, if required. Regularly check all the
screws and nuts and tighten, if required. Do not overtighten.
3. Keep the exhaust grill at front of the dryer, then install the hooks
to the dryer, in the inverted position. Remove the 2 screws and
2 plastic plugs as indicated in Fig.2.
Fig.2
2 screws
2 plastic plugs
4. Align the hooks as shown in fig.3 and refit screws tightly. Install the
spacers provided in Fig.3.
Fig.3
2 hooks
3 screws
2 spacers
6
INSTALLATION INSTRUCTIONS
5.With assistance, mount dryer on wall brackets. See Fig.4.
Fig.4
6.
A second control panel film with inverted symbols is supplied. To fit this film, pull off the knob and then remove the old film.
Peel the release paper from the back of inverted film, then place new control panel film on the surface so that the writing is the correct way around.
Sensor Dryer
Time Remaining
SDRY60CE
H MIN
Delay
6kg
Synthetics
Cottons
Delicate Plus
Iron Dry
Normal Dry
Extra Dry
Iron Dry
Normal Dry
Extra Dry
Airing
Off
40
60
75
90
10
20
30
Drying Times
(mins)
Start
(Pause)
7. Press the Start/Pause button and hold it in the pressed position, and at the
same time, turn the program dial knob from the OFF position to any other
program, until the inversion is displayed.
Caution:
Plug must be accesible after installation.
Stacking installation
You can use a stacking kit (included as an accessory) if you want to mount your dryer on the top of a Whirlpool front load washing machine, ensure the washer is the same width as the dryer.
1. Remove 4 screws among screws on the bottom panel (see fig.1), and install
the stacking kit on the bottom panel (see fig.2).
4 Screws stacking kit
Fig.1
Fig.2
7
INSTALLATION INSTRUCTIONS
2. Install the dryer with stacking kit on the top of the front load washing
machine (Fig.3). Drill two holes on both sides of washer with 2.9mm
diameter drill. Detailed drill position as shown on the stacking kit. Make
sure the included screws are used. Fix the stacking kit on the top
cover of washing machine, as shown on Fig.4.
Start
(Pause)
Drying Times
(mins)
60
40
90
75
30
20
10
Off
Airing
Extra Dry
Normal Dry
Iron Dry
Cottons
Extra Dry
Normal Dry
Synthetics
Iron Dry
Delicate Plus
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
Dryer
Stacking kit
Washer
Fig.3
Fig.4
8
INSTALLATION INSTRUCTIONS
Change the venting mode
There are three venting options:
Front venting
The exhaust grill has a range of positions, which allows you to select the optimum exhaust air angle. Simply hold the grill and rotate it until you reach the desired position.
Start
(Pause)
Drying Times
(mins)
30
20
10
60
40
90
75
Off
Airing
Extra Dry
Normal Dry
Iron Dry
Cottons
Extra Dry
Normal Dry
Iron Dry
Delicate Plus
Synthetics
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
Note: If the dryer is mounted on the wall you must use the front venting option.
Rear venting
If you want to choose the rear venting mode, the exhaust grill at the front of the dryer needs to be replaced with the outlet cover from the back panel of the dryer. Gently open the grill, using a thin tool such as a key. Next, remove the cover from the back panel and clip it into the grill space at the front panel. The exhaust grill is not required when using a flexible hose.
Start
(Pause)
Drying Times
(mins) 40
30
90
75
60
20
10
Off
Airing
Extra Dry
Normal Dry
Iron Dry
Cottons
Extra Dry
Normal Dry Synthetics
Iron Dry
Delicate Plus
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
Note: If the dryer used rear venting option without the flexible hose, it must be keeped
away from the wall not less than 50cm.
9
INSTALLATION INSTRUCTIONS
INSTALL THE FLEXIBLE HOSE( optional Flexible hose)
Connect the narrow end of the connector to the dryer duct pipe mouth at the back of the dryer.
Then connect the flexible hose to the wide end of the connector.
Use the clip to fasten connection point between the flexible hose and connector (fasten clip with a screwdriver). Extend the flexible hose through the duct hole, make sure the flexible hose is not twisted to allow the air to be vented outside.
Flexible connector
Flexible hose
Outdoor
Flexible hose clip
Vent cap
Duct hole
(diameter >100mm)
Notes: If duct hole is not available at user's home, make sure the flexible hose
is vented through a window.
The flexible hose should be angled or ensure a vent cap is fitted when
vented outside to avoid water running back into the dryer.
Correct fixing mode:
Fig.1
Fig.2
Fig.3
10
A E B
CONTROL PANEL
C E D
Start
(Pause)
Drying Times
(mins)
90
75
60
40
30
20
10
Off
Extra Dry
Normal Dry
Iron Dry
Cottons
Extra Dry
Normal Dry Synthetics
Iron Dry
Delicate Plus
Delay
Time Remaining
H MIN
SDRY60CE
Sensor Dryer
6kg
Airing
A - Start/Pause button
After selecting your desired drying program, press this button to start the dryer. To
pause the dryer while in operation, press this button again.
B - Program control knob
Turn this knob to choose the drying program you desire. This dryer has 15 program options available for you to choose.
C - Delay button
You may choose to start the dryer after a preset time. The delay range is between
1 and 12 hours. Gently touch the delay button before a program starts, each touch will add one hour. When in excess of 12 hours, the remaining time will be re-displayed.
After a delay time is set, touch the Start/Pause button to start the delay operation and the indicator light will flash.
D
-
LED screen
This screen displays the remaining time for a program and the delay time.
E
-
Indicator light
OPERATING INSTRUCTIONS
1. Power up
Insert the power plug into an appropriate power outlet that is properly installed and
grounded. Operating power supply: 220-240V~50Hz.
2. Laundry loading
Open the door and load the laundry into the drum of the dryer. For a more energy
efficient and better drying result, make sure the load has been spun dry. Try to
loosen the load when placing in the dryer.
Note:
Check labels on clothing before placing them in the dryer. Some articles are not
suitable for machine dry. High temperature may damage the fabric.
May be tumble dried
Do not tumble dry
Normal drying (high temperature)
Air dry or delicate drying (low temperature)
11
OPERATING INSTRUCTIONS
3. Selecting programme
Turn the program knob to set your desired drying program.
a. Sensor Programs
When sensor program is selected, dryness of the load will be sensed and dryer will
automatically turn itself off while the clothes have dried to the dryness level selected.
Programme D rying level Type of textile Fabrics
Max. load kg
Approximate drying times
(in minutes)
C otton
Synthetics
Extra D ry*
C upboard dry**
Iron dry**
Extra D ry**
C upboard dry**
Iron dry**
Multi-layered, thick laundry such as: terry towels, dishcloths and dry towels, bed linen, underwear, terry towelling bath robes.
Similar types of laundry which do not require ironing such as: dry towels, bed linen underwear, baby clothes, T-shirts, cotton socks.
Laundry which requires ironing such as: bed and table linen, dry towels, T-shirts, polo shirts, work clothes.
Laundry with thick, multi-layer areas such as: bed and table linen, track suits, anoraks, blankets.
Laundry which does not require ironing such as: shirts, blouses, T-shirts, sportswear.
Laundry which requires ironing such as: trousers, dresses, skirts, shirts, blouses.
Cotton or linen hot wash/coloured laundry
Synthetic, mixed fibre or cotton easy care (ironing not required) laundry
Delicate plus C upboard dry**
Low drying intensity for delicates and items labelled with , such as: trousers, dresses, shirts, blouses.
*
) Test program m e in accordance AS/N ZS2442.2
**
) Test program m e in accordance EN 61121 b. Timer Programs
It is suitable for all fabrics, completes drying for Min. 3-5 full size textiles.
c. Airing Program
Laundry is aired and refreshed for 30 minutes without heating.
Laundry made from synthetic fibres, such as polyamide, nylon, polyacrylic, etc.
6.0
3.0
2.5
165'
150'
110'
70'
60'
45'
55'
4. Delay setting
You may choose to start the dryer after a preset time. The delay range is between
1 and 12 hours.
5. Program operation
After a program is set, press the “START/PAUSE” button to start the program. If you want to change the programme after the program has started, first you must press the “START/PAUSE” button, and then you can choose the program. If you want to add or remove laundry in standby mode, you can operate directly and the press the the “START/PAUSE” button to start the dryer.
Drum reversal: The dryer is designed to rotate in each direction, clockwise and anti-clockwise in a certain period to minimize tangling and ensure clothes dry efficiently.
12
OPERATING INSTRUCTIONS
6. Program completion
If the display screen display “0.09”, the program comes into the cool phase. After the program is complete, the dryer will stop tumbling and the display screen will
display “End”. Open the door and remove the laundry.
If the laundry is not removed, the dryer will automatically commence an
"anti-crease" protection cycle to keep your laundry from settling in one position
and creasing. This cycle will last an hour unless the door is opened. The dryer
will run with cool air at set intervals. To stop the anti-crease cycle press the
start button or open the door, empty the dryer and turn off as shown below.
7.
Turning off the dryer
T urn the program knob to the “OFF” position and turn the power off at the wall.
Note:
Clean the filter after each load.
Attention:
1.Before operation, clean off any dust and dirt inside the drum of the dryer with
a damp towel.
2.Clean off any debris on the lint filter and in the duct to increase the drying efficiency.
Turning on power
Before turning on the power of the dryer, check:
- Whether the supply voltage is in accordance with the value indicated on the name plate.
- The dryer must be grounded securely.
Treatment of laundry to be dried
- Check whether the laundry to be dried is suitable to be placed in the dryer.
- The dryer can only dry laundry which has been spun dry. Do not put in laundry
which is still dripping wet or has excess water.
-
- Make sure all pockets are empty before placing laundry in the dryer.
- Pull up zippers, mend loosened fasteners and tie up ribbons to prevent the
laundry from being entangled. If necessary, put small items in a laundry bag.
To achieve a better drying result, ensure sort your laundry according to their
types and thicknesses. Dry the same types of items together.
Warning
:
Reference weight of fabrics for drying
1. Laundry items with metal attachments
may damage your dryer.
2. Do not dry items such as woollen,
silk and nylon stockings, delicate
embroidered fabrics in the machine.
3. Do not put an excess amount of
laundry into the dryer to avoid
damage to the dryer or laundry.
4. Do not dry shoes or other rubber
items in the dryer.
Overalls
(cotton appr 950g)
Blended fabric clothes
(appr 800g)
T-Shirt
(appr 300g)
Jackets (cotton appr 800g)
Woollen blankets
(appr 3000g)
Jeas (800g)
Pajamas
(appr 200g)
Shirts
(appr 300g)
Underwear
(appr 70g)
Socks
(blended fabrics) appr 50g)
Single bed sheets
(cotton appr 800g)
13
CLEANING AND MAINTENANCE
WARNING! Unplug the power cord prior to any cleaning
Cleaning the surface
Wipe off any dust or dirt.
Note:
Do not use excessive water, a damp cloth is fine.
Do not use solvent.
Do not use spray cleaners when cleaning the interior.
Do not use harsh or abrasive cleaners.
Cleaning the filter screen
To ensure good ventilation during drying, the filter screen must be cleaned before or after each use.
1. Remove the filter
Gently pull out the filter screen towards yourself.
2.Cleaning the filter
Remove the lint with a soft brush or vacuum cleaner. Be careful not to damage the filters.
3. Re-installing the filter
After cleaning filters, put the screen back in place.
Note:
Never operate your dryer without the lint filter.
14
CLEANING AND MAINTENANCE
Cleaning the door airproof strip
Remove the lint with a soft brush or a wet cloth.
Be careful not to damage the airproof strip .
Remove any remaining lint from the lint screen on the door at the same time.
Note: The door airproof strip must be cleaned
before or after each use, or the dryer
may be aleak from the door in the
operation.
Cleaning the lint in the exhaust conduit
1. Remove the outlet cover or the exhaust
grill in the trunk.
2. Take off the filter .
3. Clean the lint on the Sensor inner t he
exhaust conduit with a tool.
4. Clean the lint in the area of the exhaust
conduit with a soft brush from the hole.
Note: If there is too much lint in the exhaust conduit, it could
result in inefficient drying, it must be cleaned periodically.
hole
15
WIRING CIRCUIT
Door switch Sensor
L
N
PCB
Capacitor
Motor
Thermostat
Heater
Thermal cut-out
SPECIFICATIONS
TYPE
ITEM
Power supply
Maximum operating current (A)
Rated load (kg)
Drying program
Maximum power (W)
Dimensions (HxDxW) mm
Weight (kg)
Waterproof degree
SDRY60CE
( 220-240)V~ · 50Hz
10
6
15
2100
830x560x600
30
IPX4
16
TROUBLESHOOTING GUIDE
If a fault occurs, before contacting Whirlpool customer service, make the following checks to try and remedy the problem:
Problem Cause Explanation / Suggestion
Machine does not switch on, or the programme does not start
The product may not have been
plugged in, or turned on
Door is not closed properly
Programme may not have been set
Start/Pause button may not have been pressed
The filter may need cleaning
The machine may be overloaded
Make sure the power cord is plugged in and machine is turned on
Ensure that the loading door is properly closed
Check the programme has been selected
Ensure Start/Pause button has been pressed
Laundry is still wet at the end of cycle
F3
F4
Drying process takes too long
Programme has been interrupted without any cause
The programme has been selected is not correct
The laundry before being loaded into machine is not spum dry
The filter may need cleaning
The loading door may be ajar.
The power supply may have been cut off to the machine
A programme not suitable for the type of laundry may have been used
Laundry has shrunk, become felted, or deteriorated
Indicator light blink rapidly
Noises
A fault occurs
It's normal to hear wind sound and rubbing nose during drying process
The dryer is not placed horizontal
The Sensor is failure
The heater is failure
Clean filter after each load
Check the load does not exceed the maximum capacity for the product
Select a suitable programme according to programme chart
Do not put in laundry which is still dripping wet or has excess water
Clean filter after each load
Ensure the loading door is properly closed
Ensure there is no power failure, check the power cord is plugged in
Select a suitable programme after checking the care label on your laundry
Switch off power and check
Place the dryer in horizontal floor
Replace the Sensor
Switch off power and replace the heater
17
Whirlpool Customer Service
Before contacting Whirlpool customer service:
1. Try to remedy the problem yourself (see “Troubleshooting Guide”).
2. Restart the programme to check whether the problem solved itself.
3. If the dryer machine continues to function incorrectly, call Whirlpool customer service.
Specify:
The nature of the problem.
The dryer machine model.
Serial number.
Service
Model:SDRY60CE
Serial No.:
The Whirlpool customer service sticker can be found inside the door.
Your full address.
Your telephone number and area code.
Whirlpool customer service phone number is given on the guarantee card.
Alternatively, consult the dealer where you purchased the appliance.
version number: SDRY60CE-A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project