MB700
Socket 370 ATX
Industrial Motherboard
USER’S MANUAL
Version 1.0B
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 are trademarks of International Business Machines
Corporation.
Intel and Celeron are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
MB700 User’s Manual
Table of Contents
Introduction...............................................................1
Product Description ..........................................................1
Checklist...........................................................................2
Specifications....................................................................3
MB700 Picture ..................................................................4
Installations ..............................................................5
Installing the CPU.............................................................6
MicroPCI Daughter Card Installation ................................6
Installing the Memory (DIMM) .........................................7
Setting the Jumpers...........................................................8
Connectors on MB700.....................................................15
Watchdog Timer Configuration.......................................30
BIOS Setup..............................................................31
VGA Drivers Installation ........................................54
LAN Drivers Installation.........................................57
Audio Drivers Installation ......................................61
Appendix .................................................................65
A. I/O Port Address Map....................................................... 66
B. Interrupt Request Lines (IRQ) ......................................... 67
C. Memory Mapping ............................................................. 68
MB700 User’s Manual
iii
This page was intentionally left blank.
iv
MB700 User’s Manual
INTRODUCTION
Introduction
Product Description
MB700 is a high-performance multimedia Industrial Motherboard based
on the Intel 440BX AGPset. It features a Socket 370 architecture that
supports Intel Celeron and Coppermine processors using 66MHz and
100MHz front side bus respectively.
The MB700 packs all the functions of a versatile system, including VGA,
Audio, Ethernet and Hardware Monitoring features, into the ATX form
factor. System memory is provided by three DIMM sockets that
accommodates up to 768MB SDRAM.
The Award BIOS facilitates easy system configuration and peripheral
setup. Other advanced features include DiskOnChip flash disk support,
watchdog timer, USB and IrDA interface.
DiskOnChip flash disks are storage devices that has no moving parts and
emulates FDD/HDD with Flash/RAM/ROM offering reliable
data/program storage and long life span. They are reliable and suitable for
industrial or other harsh environments characterized by motion, shock,
vibration, adverse temperature, dust and humidity. Other features include
faster data access, longer MTBF, lower power consumption, cost
effective for small capacity and small form factor.
.
MB700 User’s Manual
1
INTRODUCTION
Checklist
Your MB700 package should include the items listed below. Damaged or
missing items should be reported to your supplier.
• The MB700 Industrial Motherboard
• This User’s Manual
• One compact disc containing the following:
• Intel PCI IDE Driver and Flash Memory Utility
• C&T 69000 VGA Drivers
• Intel 82559 Fast Ethernet Drivers
• ESS Solo-1 ES1938S Audio Drivers
• Optional cables such as:
• 1 IDE Ribbon Cable
• 1 Floppy Ribbon Cable
• 1 Bracket for 1 Serial Port
• 1 Bracket for 2 Serial Ports
2
MB700 User’s Manual
INTRODUCTION
Specifications
Processor
Supported
Chipset
BIOS
Socket 370 support Intel Celeron / Coppermine,
300MHz~850MHz, 66MHz/100MHz Bus Speed*
Intel 440BX AGPset
Award BIOS
Supports ACPI, DMI, PnP
System Memory 3x DIMM sockets support up to 768MB capacity
3.3V supported
ECC supported
Multi I/O Chipset Winbond 83977TF and 83877TF (keyboard controller is
built-in 83977TF)
I/O Features
1x FDD (up to 2.88MB, 3 Mode, LS120)
1x Parallel Port (EPP, ECP Port)
4x Serial Ports (3x RS232, 1x RS232/422/485)
1x IrDA TX/RX Headers
Bus Master IDE 2x IDE interfaces for up to 4 devices; supports PIO Mode
3/4 or Ultra DMA/33 IDE HDD, and ATAPI CD-ROM
On-board VGA
C&T 69000 PCI VGA Controller
Support CRT & LCD Panels
VGA CRT connector on board
1024x768 (High Color) resolution
2MB embedded memory
Optional C&T 69030 VGA Controller with 4MB embedded
memory
On-board Audio ESS Solo-1 (ESS1938) PCI Single Audio Chip
Provides high-quality audio processing
On-board
Intel 82559 Ethernet Controller (1x LAN or 2x LAN)
32-bit performance, PCI bus master capability
Ethernet
Supports 10/100Mbps data transfer rates
Hardware
Winbond W83781D IC
Monitors CPU/system temperature and voltages
Monitoring
SSD Interface
For M-Systems 2MB~144MB DiskOnChip flash disk
Watchdog Timer 16 levels
Digital I/O
2 In / 2 Out
Expansion Slots 5 ISA slots, 2 PCI slots, 1 MicroPCI socket
Form Factor
ATX
Dimensions
305mm x 244mm (12” x 9.6”)
Power
+5V : 10A (max)
+3.3V : 5A (max)
Requirement
+/-12V : 200mA (max)
* MB700 does not support Intel 0.13-micron Tualatin processors.
MB700 User’s Manual
3
INTRODUCTION
MB700 Picture
4
MB700 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the MB700 in order to set up a workable system. The
topics covered are:
Installing the CPU.............................................................6
MicroPCI Daughter Card Installation ................................6
Installing the Memory (DIMM) .........................................7
Setting the Jumpers...........................................................8
Connectors on MB700.....................................................15
Watchdog Timer Configuration.......................................30
MB700 User’s Manual
5
INSTALLATIONS
Installing the CPU
MB700 supports a Socket 370 processor socket for Intel Celeron/
Coppermine processors.
The Socket 370 processor socket comes with a lever to secure the
processor. Raise this lever to about a 90° angle to allow the insertion of
the processor. Place the processor into the socket by making sure the
notch on the corner of the CPU corresponds with the notch on the inside
of the socket. Once the processor has slide into the socket, return the lever
to the lock position. After you have installed the processor into the
socket, check if the jumpers for the CPU type and speed are correct.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
MicroPCI Daughter Card Installation
MB700 is integrated with one MicroPCI socket that uses SO-DIMM
144-pin connectors. These sockets can accommodate the VGA, Ethernet
or SCSI MicroPCI daughter cards.
To insert a MicroPCI daughter card, position it at about 30° (Figure 1)
to the PCB and gently push it into the MicroPCI socket. Once inserted,
slowly press the card towards the PCB until it locks on both sides to the
clips of the connector (Figure 2). Screw the card to the PCB to secure the
installation.
Figure
1. 1.
Figure
6
Figure
Figure
2. 2.
MB700 User’s Manual
INSTALLATIONS
Installing the Memory (DIMM)
The MB700 Industrial Motherboard supports three 168-pin DIMM
sockets for a maximum total memory of 768MB in SDRAM type. The
memory capacities supported are 32MB, 64MB, 128MB and 256MB.
Installing and Removing DIMMs
To install the DIMM, locate the memory slot on the Industrial
Motherboard and perform the following steps:
1. Hold the DIMM so that the two keys of the DIMM align with those on
the memory slot.
2. Gently push the DIMM in an upright position until the clips of the slot
close to hold the DIMM in place when the DIMM touches the bottom
of the slot.
3. To remove the DIMM, press the clips with both hands.
Lock
DIMM
Lock
Lock
Lock
Top View of DIMM Socket
MB700 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on the MB700 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MB700 and their respective functions.
Jumper Locations on MB700 ............................................................ 9
DSW1(3): CPU Bus Speed Selector................................................ 10
DSW1(5-8): CPU Frequency Selector ............................................ 10
JP4: LCD Power Setting .................................................................. 11
JP6, JP7, JP8: RS232/RS422/RS485 (COM2) Selection ............. 11
JP5: COM1/2 RS232 +5V / +12V Power Setting ......................... 11
JP9: COM3/4 RS232 +5V / +12V Power Setting ......................... 12
JP10: Onboard LAN2 Enable/Disable............................................. 12
JP11: Onboard LAN1 Enable/Disable............................................. 12
JP12: Onboard VGA Enable/Disable .............................................. 12
JP13: DiskOnChip Address Select................................................... 13
JP14: Watchdog Selection ............................................................... 13
JP16: Clear CMOS Content............................................................. 13
JP1, JP2, JP3: Manufacturer Testing Use ....................................... 13
S1: Panel Type Setting...................................................................... 14
The following conventions are used in this section:
off off on on
↓ ↓ ↑ ↑
8
Pin 1-2
Short/Closed
MB700 User’s Manual
INSTALLATIONS
Jumper Locations on MB700
JP6, JP7, JP8: RS232/RS422/RS485 (COM2) Selection
JP5: COM1/2 RS232 +5V / +12V Power Setting
JP9: COM3/4 RS232 +5V / +12V Power Setting
JP13: DiskOnChip Address Select
JP14: Watchdog Selection
JP16: Clear CMOS Content
S1: Panel Type Setting
JP4: LCD Power Setting
DSW1(3): CPU Bus Speed Selector
DSW1(5-8): CPU Frequency Selector
JP10: Onboard LAN2 Enable/Disable
JP11: Onboard LAN1 Enable/Disable
JP12: Onboard VGA Enable/Disable
MB700 User’s Manual
9
INSTALLATIONS
DSW1(3): CPU Bus Speed Selector
Bus Speed
DSW1(3)
Switch
Setting
100MHz
off
66MHz
on
DSW1(5-8): CPU Frequency Selector
The table below shows the correct setting to match the CPU frequency.
Frequency
Multiplier
CPU
Frequency
(66MHz)
CPU
Frequency
(100MHz)
4.5X
300MHz
450MHz
DSW1(5-8)
xx xx xx xx off on off on
5X
333MHz
500MHz
xx xx xx xx off off on on
5.5X
366MHz
550MHz
xx xx xx xx off off off on
6X
400MHz
600MHz
xx xx xx xx on on on off
6.5X
433MHz
650MHz
xx xx xx xx on on off off
7X
466MHz
700MHz
xx xx xx xx on off on off
7.5X
500MHz
750MHz
xx x x xx xx on off off off
8X
533MHz
800MHz
xx xx xx xx off on on off
10
MB700 User’s Manual
INSTALLATIONS
JP4: LCD Power Setting
JP4
Setting
Function
Pin 1-2
Short/Closed
3.3V
Pin 2-3
Short/Closed
5V
JP6, JP7, JP8: RS232/RS422/RS485 (COM2) Selection
JP8, JP7, JP6
Pin Short
Function
JP8: 1-2
JP7: 3-5, 4-6
JP6: 3-5, 4-6
RS232
JP8: 3-4
JP7: 1-3, 2-4
JP6: 1-3, 2-4
RS422
JP8: 5-6
JP7: 1-3, 2-4
JP6: 1-3, 2-4
RS485
JP5: COM1/2 RS232 +5V / +12V Power Setting
JP5 Pin #
Signal Name
1
JP5
Signal Name
JP7 Pin #
+5V
+5V
2
3
Pin 9 (COM1)
Pin 9 (COM2)
4
5
+12V
+12V
6
COM1 Settings: Pin 1-3 short = +5V, Pin 3-5 short = +12V
COM2 Settings: Pin 2-4 short = +5V, Pin 4-6 short = +12V
MB700 User’s Manual
11
INSTALLATIONS
JP9: COM3/4 RS232 +5V / +12V Power Setting
JP9 Pin #
Signal Name
1
JP9
Signal Name
JP7 Pin #
+5V
+5V
2
3
Pin 9 (COM3)
Pin 9 (COM4)
4
5
+12V
+12V
6
COM3 Settings: Pin 1-3 short = +5V, Pin 3-5 short = +12V
COM4 Settings: Pin 2-4 short = +5V, Pin 4-6 short = +12V
JP10: Onboard LAN2 Enable/Disable
JP10
Setting
LAN2 Function
Pin 1-2
Short/Closed
Enabled
Pin 2-3
Short/Closed
Disabled
JP11: Onboard LAN1 Enable/Disable
JP11
Setting
LAN1 Function
Pin 1-2
Short/Closed
Enabled
Pin 2-3
Short/Closed
Disabled
JP12: Onboard VGA Enable/Disable
JP12
12
Setting
VGA Function
Pin 1-2
Short/Closed
Enabled
Pin 2-3
Short/Closed
Disabled
MB700 User’s Manual
INSTALLATIONS
JP13: DiskOnChip Address Select
JP13
Setting
Address
Pin 1-2
Short/Closed
D0000-D7FFF
(default)
Pin 2-3
Short/Closed
D8000-DFFFF
JP14: Watchdog Selection
JP14
Setting
Function
Pin 1-2
Short/Closed
Reset (default)
Pin 2-3
Short/Closed
NMI
JP16: Clear CMOS Contents
Use JP16, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the CPU card
before clearing CMOS.
JP16
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP1, JP2, JP3: Manufacturer Testing Use
JP1, JP2 and JP3 have no definition in this manual and are used for
manufacturer testing purposes.
MB700 User’s Manual
13
INSTALLATIONS
S1: Panel Type Setting
The S1 Panel Type Setting switch is only used when your system supports
LCD panels. Please note, however, that the BIOS shipped with your
MB700 supports only CRT. You will need another BIOS to support your
LCD panel. If you have any question, please contact your SBC vendor.
SW DIP Switch
1
2
3
4
Panel Type
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
On
Off
Off
On
On
Off
Off
On
On
Off
Off
On
On
On
On
On
On
Off
Off
Off
Off
On
On
On
On
Off
Off
On
On
On
On
On
On
On
On
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
1024 x 768 Dual Scan STN Color Panel
1280 x 1024 TFT Color Panel
640 x 480 Dual Scan STN Color Panel
800 x 600 Dual Scan STN Color Panel
640 x 480 Sharp TFT Color Panel
640 x 480 18-bit TFT Color Panel
1024 x 768 TFT Color Panel
800 x 600 TFT Color Panel
800 x 600 TFT Color Panel (Large BIOS only)
800 x 600 TFT Color Panel (Large BIOS only)
800 x 600 TFT Color Panel (Large BIOS only)
800 x 600 TFT Color Panel (Large BIOS only)
1024 x 768 TFT Color Panel (Large BIOS only)
1280 x 1024 Dual Scan STN Color Panel (Large
BIOS only)
1024 x 768 Dual Scan STN Color Panel (Large
BIOS only)
1024 x 600 TFT Color Panel (Large BIOS only)
14
MB700 User’s Manual
INSTALLATIONS
Connectors on MB700
The connectors on MB700 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following
table lists the connectors on MB700 and their respective functions.
Connector Locations on MB700 ..................................................... 16
J1: PS/2 Keyboard and PS/2 Mouse Connectors............................ 17
J2: USB and LAN1 RJ45 Connectors ............................................. 17
J3, J13, J14, J15: Serial Ports.......................................................... 18
J4: Parallel Port Connector.............................................................. 19
J5: VGA CRT Connector................................................................. 19
J6, J7, J8, J9: Line Out, Line In, Mic In, Game Port....................... 20
J10: ATX Power Supply Connector ................................................ 20
J11: CPU Fan Power Connector ..................................................... 20
J12: LCD Panel Connector .............................................................. 21
Flat Panel Display Interface Pin Descriptions................................. 22
J16: Floppy Drive Connector........................................................... 23
J18, J17: EIDE Connectors.............................................................. 24
J19: CD-In Audio Connector........................................................... 25
J21: LAN2 RJ45 Connector ............................................................ 26
J27: Digital I/O Connector............................................................... 26
J30: System Fan Power Connector.................................................. 27
J32: IrDA Connector ........................................................................ 27
J33: System Function Connector..................................................... 27
J35: Wake on LAN Connector......................................................... 29
MB700 User’s Manual
15
INSTALLATIONS
Connector Locations on MB700
J33: System Function Connector
J30: System Fan Power Connector
J32: IrDA Connector
J35: Wake on LAN Connector
J16: Floppy Drive Connector
J18, J17: EIDE Connectors
J12: LCD Panel Connector
J21: LAN2 RJ45 Connector
J19: CD-In Audio Connector
J27: Digital I/O Connector
J6, J7, J8, J9: Line Out, Line In,
Mic In, Game Port
J5: VGA CRT Connector
J11: CPU Fan Power Connector
J4: Parallel Port Connector
J3, J13, J14, J15: Serial Ports
J10: ATX Power Connector
J2: USB and LAN1 RJ45 Connectors
J1: PS/2 Keyboard and PS/2 Mouse Connectors
16
MB700 User’s Manual
INSTALLATIONS
J1: PS/2 Keyboard and PS/2 Mouse Connectors
PS/2 Mouse
PS/2 Keyboard
Below are the pin-out assignments of the connectors.
Signal Name
Keyboard data
N.C.
GND
5V
Keyboard clock
N.C.
Keyboard
1
2
3
4
5
6
Mouse
1
2
3
4
5
6
Signal Name
Mouse data
N.C.
GND
5V
Mouse clock
N.C.
J2: USB and LAN1 RJ45 Connectors
J2 consists of an RJ-45 connector (top) and two stacked USB ports. Refer
to the section below for their respective pin assignments.
USB0
USB1
Pin #
1
2
3
4
Signal Name
Vcc
USBUSB+
Ground
MB700 User’s Manual
17
INSTALLATIONS
J3, J13, J14, J15: Serial Ports
J3 (COM1) is a DB-9 connector, while J13 (COM2), J14 (COM3) and
J15 (COM4). Refer to the table below for their pin assignments.
COM1
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
COM2/COM3/COM4
Pin #
1
2
3
4
5
Pin #
6
7
8
9
10
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
J13 (COM2) is jumper selectable for RS-232, RS-422 and RS-485.
Pin #
RS-232
1
2
3
4
5
6
7
8
9
10
18
DCD
RX
TX
DTR
Ground
DSR
RTS
CTS
RI
NC
Signal Name
R2-422
RS-485
TXTX+
RX+
RXGround
RTSRTS+
CTS+
CTSNC
MB700 User’s Manual
DATADATA+
NC
NC
Ground
NC
NC
NC
NC
NC
INSTALLATIONS
J4: Parallel Port Connector
J4 is a DB-25 external connector situated on top of the VGA and serial
ports. The following table describes the pin-out assignments of this
connector.
J4 Parallel Port
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
N/A
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
J5: VGA CRT Connector
J5 is a DB-15 VGA connector located beside the COM1 port. The
following table shows the pin-out assignments of this connector.
Signal Name Pin #
Red
Blue
GND
GND
N.C.
N.C.
HSYNC
NC
1
3
5
7
9
11
13
15
MB700 User’s Manual
Pin # Signal Name
2
Green
4
N.C.
6
GND
8
GND
10
GND
12
N.C.
14
VSYNC
19
INSTALLATIONS
J6, J7, J8, J9: Line Out, Line In, Mic In, Game Port
The figure below shows the location of J6 (Line Out), J7 (Line In), J8
(Mic In), and J9 (Game Port).
Game Port
LineOut LineIn MicIn
J10: ATX Power Supply Connector
J10 is a 20-pin ATX power supply connector. Refer to the following table
for the pin out assignments.
11
1
20
10
Signal Name
3.3V
-12V
Ground
PS-ON
Ground
Ground
Ground
-5V
+5V
+5V
Pin #
11
12
13
14
15
16
17
18
19
20
Pin #
1
2
3
4
5
6
7
8
9
10
Signal Name
3.3V
3.3V
Ground
+5V
Ground
+5V
Ground
Power good
5VSB
+12V
J11: CPU Fan Power Connector
J11 is a 3-pin header for a CPU fan. The fan must be a 12V fan.
Pin #
1
2
3
20
Signal Name
Rotation
+12V
Ground
MB700 User’s Manual
INSTALLATIONS
J12: LCD Panel Connector
J12 is the pin header for flat panel LCD displays. The following shows the
pin assignments of this connector.
50
49
2 J12 1
Signal Name
GND
P34
P35
P30
P29
P25
P24
P23
P16
P17
P19
P13
P15
P7
5V or 3.3V
P9
P4
P3
P2
M
SHFCLK
FPVDD
FPVEE
GND
+12V
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
MB700 User’s Manual
Pin # Signal Name
2
P33
4
P31
6
P32
8
P28
10
P27
12
P26
14
P21
16
P22
18
P20
20
P18
22
P14
24
P12
26
P11
28
P10
30
5V or 3.3V
32
P8
34
P6
36
P5
38
P1
40
P0
42
ENABKL
44 FLM(V SYNC)
46
LP(H SYNC)
48
GND
50
+12V
21
INSTALLATIONS
Flat Panel Display Interface Pin Descriptions
Pin Name
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
P31
P32
P33
P34
P35
SHFCLK
Pixels/Clk:
Color
Color
Color
Color
Color
Mono Mono Mono Color Color Color Color
SS
DD
DD
TFT
TFT
TFT TFT TFT+HR STN-SS STN-SS STN-DD STN-DD
8-bit 8-bit 16-bit 9/12/16 18/24 36-bit 18/24
8-bit
16-bit
8-bit
16-bit
24-bit
bit
bit
bit
(4bP)
(4bP)
(4bP)
(4bP)
D0
UD3 UD7
B0
B0
FB0 FB0
R1
R1
UR1
UR0
UR0
D1
UD2 UD6
B1
B1
FB1 FB1
B1
G1
UG1
UG0
UG0
D2
UD1 UD5
B2
B2
FB2 FB2
G2
B1
UB1
UB0
UB0
D3
UD0 UD4
B3
B3
FB3 FB3
B3
R2
UB2
UR1
LR0
D4
LD3
UD3
B4
B4
FB4 SB0
G4
G3
LR1
LR0
LG0
D5
LD2
UD2
G0
B5
FB5 SB1
R5
B2
LG1
LG0
LB0
D6
LD1
UD1
G1
B6
SB0 SB2
B5
R3
LB1
LB0
UR1
D7
LD0
UD0
G2
B7
SB1
B3
G3
LR2
LR1
UG1
LD7
G3
G0
SB2 FG0
B3
UG1
UB1
LD6
G4
G1
SB3 FG1
R4
UB1
LR1
LD5
G5
G2
SB4 FG2
G4
UR2
LG1
LD4
R0
G3
SB5 FG3
B4
UG2
LB1
LD3
R1
G4
FG0 SG0
R5
LG1
UR2
LD2
R2
G5
FG1 SG1
G5
LB1
UG2
LD1
R3
G6
FG2 SG2
B5
LR2
UB2
LD0
R4
G7
FG3 SG3
G6
LG2
LR2
R0
FG4 FR0
LG2
R1
FG5 FR1
LB2
R2
SG0 FR2
UR3
R3
SG1 FR3
UG3
R4
SG2 SR0
LR3
R5
SG3 SR1
LG3
R6
SG4 SR2
LB3
R7
SG5 SR3
FR0
FR1
FR2
FR3
FR4
FR5
SR0
SR1
SR2
SR3
SR4
SR5
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
8
8
16
1
1
2
2
2-2/3
5-1/3
2-2/3
5-1/3
8
P24
22
MB700 User’s Manual
INSTALLATIONS
J16: Floppy Drive Connector
J16 of the MB700 is a 34-pin header and will support up to 2.88MB
floppy drives.
Signal Name
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
MB700 User’s Manual
Signal Name
RM/LC
No connect
No connect
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Step
Write data
Write gate
Track 00
Write protect
Read data
Side 1 select
Diskette change
23
INSTALLATIONS
J18, J17: EIDE Connectors
J18 is the primary IDE connector. J17 is the secondary IDE connector.
J18: IDE1
24
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
IRQ14
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
MB700 User’s Manual
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
INSTALLATIONS
J17: IDE2
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK1
MIRQ0
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
J19: CD-In Audio Connector
Pin #
1
2
3
4
Signal Name
CD Audio L
Ground
Ground
CD Audio R
MB700 User’s Manual
25
INSTALLATIONS
J21: LAN2 RJ45 Connector
J21, an RJ45 connector, is for the external LAN connector. The MB700
supports both 10Mbps and 100Mbps LAN facilities.
Signal Name
Pin #
Pin #
Signal Name
LED1+
RX+
LED2LED2+
TX+
1
3
5
7
9
2
4
6
8
10
LED1RXGround
Ground
TX-
J27: Digital I/O Connector
This 10-pin Digital I/O connector supports TTL levels and is used to
control external devices requiring ON/OFF circuitry.
Signal Name
DI0
DI1
No Connect
No Connect
Ground
Pin #
1
2
3
4
5
Pin #
6
7
8
9
10
Signal Name
Vcc
DO0
Ground
DO1
+12V
SPECIFICATIONS:
Digital Input
Input channels: 2 bits
Input Voltage: High: 2.0V (min)
Low: 0.8V (max)
Input Load:
High: 0.05mA max at 2.7V
Low: 0.4mA max at 0.5V
Register Address: 260H
Register Format: BIT:
D1 D0
Value: DI1 DI0
Digital Output
Output channels: 2 bits
Output voltage: High: Source -0.4mA at 2.4V min
Low: Sink 8mA at 0.5V max
Register Address: 260H (Write)
Register Format: BIT:
D1
D0
Value: DO1 DO0
26
MB700 User’s Manual
INSTALLATIONS
J30: System Fan Power Connector
J30 is a 3-pin header for the system fan. The fan must be a 12V fan.
Pin #
1
2
3
Signal Name
Rotation
+12V
Ground
J32: IrDA Connector
This connector is used for an IrDA connector for wireless
communication.
Pin #
Signal Name
+5V IRRX IRTX
1
+5V
2
No Connect
3
Ir RX
N.C. GND
4
Ground
5
Ir TX
J33: System Function Connector
J33 provides connectors for system indicators that provides light
indication of the computer activities and switches to change the computer
status. J1 is a 20-pin header that provides interfaces for the following
functions.
Hard Disk Drive LED
Reset Switch
Turbo LED Connector
ATX Power On Switch
SMI / Hardware Switch
Power LED and Keylock
Speaker
MB700 User’s Manual
27
INSTALLATIONS
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
Pin #
Signal Name
1
Speaker out
2
No connect
3
Ground
4
+5V
Power LED and Keylock: Pins 11 - 15
The power LED indicates the status of the main power
switch. The keylock switch, when closed, will disable the
keyboard function.
Pin #
Signal Name
11
Power LED
12
No connect
13
Ground
14
Keylock
15
Ground
SMI/Hardware Switch: Pins 6 and 16
This connector supports the "Green Switch" on the control
panel, which, when pressed, will force the system into the
power-saving mode immediately.
Pin #
Signal Name
6
Sleep
16
Ground
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
28
MB700 User’s Manual
INSTALLATIONS
Turbo LED Connector: Pins 8 and 18
There is no turbo/deturbo function on the CPU card. The
Turbo LED on the control panel will always be On when
attached to this connector.
Pin #
8
18
Signal Name
5V
Ground
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to this
header.
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
Pin #
Signal Name
10
Ground
20
5V
J35: Wake on LAN Connector
J35 is a 3-pin header for the Wake on LAN function on the motherboard.
The table below shows the pin out assignments of this connector. Wake
on LAN will function properly only with an ATX power supply with
5VSB that has 1A.
1
2
3
Pin #
1
2
3
Signal Name
+5VSB
Ground
Wake on LAN
MB700 User’s Manual
29
INSTALLATIONS
Watchdog Timer Configuration
The function of the watchdog timer is to reset the system automatically
and is defined at I/O port 0443H. To enable the watchdog timer and allow
the system to reset, write I/O port 0443H. To disable the timer, write I/O
port 0441H for the system to stop the watchdog function. The timer has a
tolerance of 20% for its intervals.
The following describes how the timer should be programmed.
Enabling Watchdog:
MOV AX, 000FH (Choose the values from 0)
MOV DX, 0443H
OUT
DX, AX
Disabling Watchdog
MOV AX, 00FH (Any value is fine.)
MOV DX, 0441H
OUT
DX, AX
WATCHDOG TIMER CONTROL TABLE
Level
1
2
3
4
5
6
7
8
30
Value
F
E
D
C
B
A
9
8
Time/sec
0
2
4
6
8
10
12
14
Level
9
10
11
12
13
14
15
16
MB700 User’s Manual
Value
7
6
5
4
3
2
1
0
Time/sec
16
18
20
22
24
26
28
30
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award BIOS
that comes with the CPU card. The topics covered in this chapter are as
follows:
BIOS Introduction ............................................................................ 32
BIOS Setup........................................................................................ 32
Standard CMOS Setup...................................................................... 34
BIOS Features Setup ........................................................................ 37
Chipset Features Setup..................................................................... 40
Power Management Setup................................................................ 43
PNP/PCI Configuration................................................................... 46
Load BIOS Defaults ......................................................................... 48
Load Setup Defaults ......................................................................... 48
Integrated Peripherals ....................................................................... 49
Supervisor / User Password............................................................. 51
IDE HDD Auto Detection................................................................ 52
Save & Exit Setup............................................................................. 53
Exit Without Saving ......................................................................... 53
MB700 User’s Manual
31
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your computer
system’s ROM supports Intel Pentium II processors in a standard
IBM-AT compatible I/O system. The BIOS provides critical low-level
support for a standard device such as disk drives, serial ports and parallel
ports. It also adds virus and password protection as well as special
support for detailed fine-tuning of the chipset controlling the entire
system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you to
enter the Setup utility. If you are a little bit late pressing the <Del> key,
POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to select,
the <PgUp> and <PgDn> keys to change entries, <F1> for help and
<Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on the
screen. The Main Menu allows you to select from various setup functions
and exit choices.
32
MB700 User’s Manual
BIOS SETUP
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Time, Date, Hard Disk Type
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section which displays information
on the currently highlighted item in the list.
Note:
If your computer cannot boot after making and saving
system changes with Setup, the Award BIOS supports an
override to the CMOS settings that resets your system to its
default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum
performance and reliability. Changing the defaults could
cause the system to become unstable and crash in some
cases.
MB700 User’s Manual
33
BIOS SETUP
Standard CMOS Setup
The “Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the card is already installed in a working
system, you will not need to select this option. You will need to run the
Standard CMOS option, however, if you change your system hardware
configurations, the onboard battery fails, or the configuration stored in
the CMOS memory was lost or damaged.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Wed, Mar 4 1998
Time (hh:mm:ss) :
00 : 00 : 00
HARD DISKS
TYPE
SIZE
LANDZ
SECTOR
MODE
Primary Master
Primary Slave
Auto
0
CYLS HEAD PRECOMP
0
0
0
0
0
Auto
Auto
0
0
0
0
0
0
Auto
Secondary Master
Auto
0
0
0
0
0
0
Auto
Secondary Slave
Auto
0
0
0
0
0
0
Auto
Drive A
: 1.44M, 3.5in
Drive B
: None
Video
: EGA / VGA
Halt On
: All Errors
Base Memory
:
640K
Extended
Memory
:
15360K
Other Memory
:
384K
Total Memory
:
16384K
ESC : Quit
á â à ß : Select
F1 : Help
(Shift) F2 : Change Color
Item
PU / PD / + / - : Modify
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following describes
each item of this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
Sun to Sat
1 to 12
1 to 31
1994 to 2079
To set the date, highlight the “Date” field and use the PageUp/ PageDown
or +/- keys to set the current time.
34
MB700 User’s Manual
BIOS SETUP
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
Primary HDDs / Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary
channels for connecting up to four IDE hard disks or other IDE devices.
Each channel can support up to two hard disks; the first is the “Master”
and the second is the “Slave”.
To enter the specifications for a hard disk drive, you must select first a
“Type”. There are 45 predefined types and 4 user definable types are for
Enhanced IDE BIOS. Type 1 to 45 are predefined. Type “User” is
user-definable. For the Primary Master/Slave as well as Secondary
Master/Slave, you can select “Auto” under the TYPE and MODE fields.
This will enable auto detection of your IDE drives and CD-ROM drive
during POST.
Press <PgUp>/<PgDn> to select a numbered hard disk type or type the
number and press the <Enter> key. The hard disk will not work properly if
you enter incorrect information for this field. If your hard disk drive type
is not matched or listed, you can use Type User to define your own drive
type manually. If you select Type User, related information is asked to be
entered to the following items.
CYLS :
Number of cylinders
HEAD :
Number of read/write heads
PRECOMP : Write precompensation
LANDZ :
Landing zone
SECTOR :
Number of sectors
SIZE :
Automatically adjust according to the configuration
MODE (for IDE HDD only) : Auto
Normal (HD < 528MB)
Large (for MS-DOS only)
LBA (HD > 528MB and supports
Logical Block Addressing)
MB700 User’s Manual
35
BIOS SETUP
NOTE: The specifications of your drive must match with the drive
table. The hard disk will not work properly if you enter
incorrect information in these fields. If your hard disk drive
type is not matched or listed, you can use Type User to define
your own drive type manually.
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB
2MB
720KB 44MB
88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
Halt On
This field determines whether the system will halt if an error is detected
during power up.
No errors
The system boot will not be halted for any error
that may be detected. (default)
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
All, But Keyboard
The system boot will not be halted for a
keyboard error; it will stop for all other errors
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
36
MB700 User’s Manual
BIOS SETUP
BIOS Features Setup
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
ROM / PCI ISA BIOS
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning
: Disabled
Video BIOS Shadow
: Enabled
CPU Internal Cache
: Enabled
C8000-CBFFF Shadow
: Disabled
External Cache
: Enabled
CC000-CFFFF Shadow
: Disabled
CPU L2 Cache ECC Checking
: Enabled
D0000-D3FFF Shadow
: Disabled
Processor Number Feature
: Enabled
D4000-D7FFF Shadow
: Disabled
Quick Power On Self Test
: Enabled
D8000-DBFFF Shadow
: Disabled
Boot Sequence
: A, C, SCSI
DC000-DFFF Shadow
: Disabled
Swap Floppy Drive
: Disabled
Boot Up Numlock Status
: On
Gate A20 Option
: Fast
Typematic Rate Setting
: Disabled
Typematic Rate (chars/Sec)
:6
Typematic Delay (Msec)
: 250
Security Option
: Setup
PCI /VGA Palette Snoop
: Disabled
OS Select For DRAM>64MB
: Non-OS2
ESC : Quit
á â à ß : Select Item
Report No FDD For WIN 95
: Yes
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Virus Warning
This item protects the boot sector and partition table of your hard disk
against accidental modifications. If an attempt is made, the BIOS will halt
the system and display a warning message. If this occurs, you can either
allow the operation to continue or run an anti-virus program.
CPU Internal Cache / External Cache
When the CPU requests data, the system transfers the requested data from
the main DRAM into cache memory, for even faster access by the CPU.
These items allow you to enable (speed up memory access) or disable the
cache function. By default, these items are Enabled.
CPU L2 Cache ECC Checking
When enabled, this allows ECC checking of the CPU’s L2 cache. By
default, this field is Enabled.
Processor Number Feature
This field only appears if the processor on board is a Pentium III
processor. The Processor Number Feature can be enabled or disabled.
MB700 User’s Manual
37
BIOS SETUP
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some items.
Boot Sequence
This field determines the drive that the system searches first for an
operating system. The options are:
A, C, SCSI
D, A, SCSI
SCSI, C, A
C, A, SCSI
E, A, SCSI
C only
C, CDROM, A
F, A, SCSI
LS/ZIP, C
CDROM, C, A
SCSI, A, C
The default value is A, C, SCSI.
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default, this
field is set to Disabled.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the
system. By default, the system boots up with NumLock On.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB. The default setting is Fast.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. You can select speed range from 6 to 30 characters per
second. By default, this item is set to 6.
38
MB700 User’s Manual
BIOS SETUP
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA Cards
can work with PCI/VGA. When this field is enabled, a PCI/VGA can
work with an MPEG ISA/VESA VGA card. When this field is disabled, a
PCI/VGA cannot work with an MPEG ISA/VESA Card.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
This option allows Windows 95 to share with other peripherals IRQ6
which is assigned to a floppy disk drive if the drive is not existing..
Video BIOS Shadow
This item allows you to change the Video BIOS location from ROM to
RAM. Video Shadow will increase the video speed.
C8000 - CBFFF Shadow/DC000 - DFFFF Shadow
Shadowing a ROM reduces the memory available between 640KB to
1024KB. These fields determine whether or not optional ROM will be
copied to RAM.
MB700 User’s Manual
39
BIOS SETUP
Chipset Features Setup
This Setup menu controls the configuration of the chipset.
ROM PCI/ISA BIOS
CHIPSET FEATURES SETUP
AWARD SOFTWARE INC.
SDRAM RAS-to-CAS Delay
SDRAM RAS Precharge Time
SDRAM CAS Latency Time
SDRAM Precharge Control
DRAM Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Video RAM Cacheable
8 Bit I/O Recovery Time
16 Bit I/O Recovery Time
Memory Hole At 15MB-16MB
Passive Release
Delayed Transaction
AGP Aperture Size (MB)
:3
:3
:3
: Disabled
: Non-ECC
: Disabled
: Disabled
: Disabled
:3
:2
: Disabled
: Enabled
: Ensabled
: 64
Auto Detect DIMM/PCI Clock
Spread Spectrum
: Disabled
: Disabled
CPU Warning Temperature
:
Current System Temp.
:
Current CPU Temp.
:
Current CPU Fan Speed
:
Current Chassis Fan Speed
:
VCCP (V) : 1.98 V
VTT (V)
VCC3 (V) : 3.45 V
+5V
+12 V
: 12.46 V
-12 V
-5V
: - 5.21 V
66°C/151°F
41°C/ 105°F
27°C/ 80°F
2789 RPM
2045 RPM
:
1.50 V
:
4.99 V
: -12.54V
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
SDRAM RAS-to-CAS Delay
When DRAM is refreshed, both rows and columns are addressed
separately. This field allows you to determine the timing of transition
from Row Address Strove (RAS) to Column Address Strobe (CAS). The
default setting is 3.
SDRAM RAS Precharge Time
The precharge time is the number of cycles it takes for the RAS to
accumulate its charge before DRAM refresh. If insufficient time is
allowed, refresh may be incomplete and the DRAM may fail to retain
data. The default setting is 3.
SDRAM CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of
CAS latency depends on the DRAM timing. Do not reset this field from
the default value specified by the system designer. The default value is 3.
SDRAM Precharge Control
By default, the SDRAM Precharge Control field is set to Disabled.
System BIOS Cacheable
When enabled, access to the system BIOS ROM addressed at
F0000H-FFFFFH is cached, provided that the cache controller is
disabled.
40
MB700 User’s Manual
BIOS SETUP
Video BIOS Cacheable
The Setting Enabled allows caching of the video BIOS ROM at
C0000h-F7FFFh, resulting in better video performance. However, if any
program writes to this memory area, a system error may result.
Video RAM Cacheable
Selecting Enabled allows caching of the video BIOS ROM at C0000h to
C7FFFh, resulting in better video performance. However, if any program
writes to this memory area, a memory access error may result.
8 Bit I/O Recovery Time
This option specifies the length of the delay (in sysclks) inserted between
consecutive 8-bit I/O operations. The settings are 1, 2, 3, 4, 5, 6, 7, and 8.
The default setting is 3.
16 Bit I/O Recovery Time
This option specifies the length of the delay (in sysclks) inserted between
consecutive 16-bit I/O operations. The settings are 1, 2, 3, and 4. The
default setting is 2.
Memory Hole at 15MB - 16MB
In order to improve performance, certain space in memory can be reserved
for ISA cards. This field allows you to reserve 15MB to 16MB of
memory address space to ISA expansion cards. This makes memory from
15MB and up unavailable to the system. Expansion cards can only access
memory up to 16MB. By default, this field is set to Disabled.
Passive Release
When enabled, CPU to PCI bus accesses are allowed during passive
release. Otherwise, the arbiter only accepts another PCI master access to
local DRAM.
Delayed Transaction
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1. The default setting is Disabled.
MB700 User’s Manual
41
BIOS SETUP
AGP Aperture Size (MB)
The field sets aperture size of the graphics. The aperture is a portion of the
PCI memory address range dedicated for graphics memory address space.
Host cycles that hit the aperture range are forwarded to the AGP without
any translation. The options available are 4M, 8M, 16M, 32M, 64M,
128M and 256M. The default setting is 64M.
Auto Detect DIMM/PCI Clk
When enabled, the system automatically shuts off clocks of unused
DIMM/PCI slots. The default setting is Disabled. This field is for CE
testing use only.
Spread Spectrum
This field sets the value of the spread spectrum. Options are Disabled,
0.25% and 0.5%. The default setting is Disabled. This field is for CE
testing use only.
CPU Warning Temperature
This field sets the threshold temperature at which an alert is sounded
through the system’s speaker. The CPU temperature is monitored by the
onboard thermal sensor to prevent the CPU from overheating.
Current System Temp./ Current CPU Temp.
These read-only fields reflect the functions of the hardware thermal
sensor that monitors the chip blocks and system temperatures to ensure
the system is stable.
Current CPU Fan Speed/Chassis Fan Speed
These optional and read-only fields show the current speeds in RPM
(revolution per minute) for the CPU fan and chassis fan as monitored by
the hardware monitoring IC.
VCCP / VTT / VCC3
These optional and read-only fields show the current voltages in the
voltage regulators and power supply as monitored by the hardware
monitoring IC.
42
MB700 User’s Manual
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively. It will shut down the hard disk and turn off video display after
a period of inactivity.
ROM PCI/ISA BIOS
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
ACPI Function
: Enabled
Power Management
: User Define
IRQ3 (3-7, 9-15), NMI
: Disabled
PM Control by APM
: Yes
Primary IDE 0
: Enabled
Video Off Method
: V/H SYNC +Blank
Primary IDE 1
: Enabled
Video Off After
: Standby
Secondary IDE 0
: Disabled
MODEM Use IRQ
:3
Secondary IDE 1
: Disabled
Doze Mode
: Disabled
Floppy Disk
: Disabled
Standby Mode
: Disabled
Serial Port
: Enabled
Suspend Mode
: Disabled
Parallel Port
: Disabled
HDD Power Down
: Disabled
Throttle Duty Cycle
: 62.5%
PCI VGA Active Monitor
: Disabled
Soft-Off by PWR-BTTN
: Instant-Off
Power On by Ring
: Disabled
Resume by Alarm
: Disabled
IRQ 8 Break Suspend
: Disabled
** Reload Global Timer Events **
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
ACPI Function
This field allows you to enabled or disable the ACPI function on the
motherboard. By default, this field is set to Disabled.
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Minimum power management
Max. Power Saving
Maximum power management.
Each of the ranges is from 1 min. to 1hr.
User Define
Except for HDD Power Down which
ranges from 1 min. to 15 min.
(Default)
NOTE:
In order to enable the CPU overheat protection feature, the
Power Management field should not be set to Disabled.
MB700 User’s Manual
43
BIOS SETUP
PM Control by APM
This field allows you to use the Advanced Power Management device to
enhance the Max. Power Saving mode and stop the CPU’s internal clock.
If the Max. Power Saving is not enabled, this will be preset to NO.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank Default setting, blank the screen and turn off
vertical and horizontal scanning.
DPMS
Allows the BIOS to control the video display card if it
supports the DPMS feature.
Blank Screen This option only writes blanks to the video buffer.
Video Off After
As the system moves from lesser to greater power-saving modes, select
the mode in which you want the monitor to blank.
Modem Use IRQ
This field names the interrupt request (IRQ) line assigned to the modem
(if any) on your system. Activity of the selected IRQ always awakens the
system. By default, the IRQ is set to 3.
Doze Mode
When enabled, and after the set time of system inactivity, the CPU clock
will run at a slower speed while all other devices still operate at full
speed.
Standby Mode
After the selected period of system inactivity, the fixed disk drive and the
video shut off while all other devices still operate at full speed.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Throttle Duty Cycle
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
44
MB700 User’s Manual
BIOS SETUP
PCI VGA Active Monitor
When enabled, any video activity restarts the global timer for Standby
mode. The default setting is Enabled.
Soft-Off by PWR-BTTN
This field defines the power-off mode when using an ATX power supply.
The Instant-Off mode allows powering off immediately upon pressing the
power button. In the Delay 4 Sec mode, the system powers off when the
power button is pressed for more than four seconds or places the system
in a very low-power-usage state, with only enough circuitry receiving
power to detect power button activity or Resume by Ring activity (see
next field) when pressed for less than 4 seconds. The default value is
Instant-Off.
Power On by Ring
An input signal on the serial Ring Indicator (RI) line (in other words, an
incoming call on the modem) awakens the system from a soft off state.
Resume by Alarm
This allows a computer to be turned on automatically through the timer
set in the BIOS to make the system more schedulable. By default, this
field is set to Disabled.
IRQ 8 Break Suspend
You can enable or disable the monitoring of IRQ 8 (Real Time Clock) so
it does not awaken the system from Suspend mode.
Reload Global Timer Events
This section determines the reloading of the ‘timers’ after entering the
Full On You can enable or disable the monitoring of IRQ 8 (Real Time
Clock) so it does not awaken the system from Suspend mode.
MB700 User’s Manual
45
BIOS SETUP
PNP/PCI Configuration
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
ROM PCI/ISA BIOS
PNP/PCI CONFIGURATION
AWARD SOFTWARE INC.
PNP OS Installed
: No
Resources Controlled by
: Manual
Used MEM base addr
: N/A
Reset Configuration Data
: Disabled
IRQ-3
assigned to
: Legacy ISA
IRQ-4
assigned to
: Legacy ISA
IRQ-5
assigned to
: PCI/ISA PnP
IRQ-7
assigned to
: Legacy ISA
IRQ-9
assigned to
: PCI/ISA PnP
IRQ-10 assigned to
: PCI/ISA PnP
IRQ-11 assigned to
: PCI/ISA PnP
IRQ-12 assigned to
: PCI/ISA PnP
IRQ-14 assigned to
: PCI/ISA PnP
IRQ-15 assigned to
: PCI/ISA PnP
DMA-0 assigned to
: PCI/ISA PnP
DMA-1 assigned to
: PCI/ISA PnP
ESC : Quit
á â ß : Select Item
DMA-3 assigned to
: PCI/ISA PnP
F1 : Help
PU/PD/+/- : Modify
DMA-5 assigned to
: PCI/ISA PnP
F5 : Old Values
(Shift) F2 : Color
DMA-6 assigned to
: PCI/ISA PnP
F6 : Load BIOS Defaults
DMA-7 assigned to
: PCI/ISA PnP
F7 : Load Setup Defaults
PNP OS Installed
This field allows you to specify if the operating system installed in your
system is plug and play aware.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
automatically. However, this capability needs you to use a PnP operating
system such as Windows 95. The default value is Manual.
Reset Configuration Data
This field allows you to determine whether or not to reset the
configuration data. The default value is Disabled.
IRQ3/4/5/7/9/10/11/12/14/15, DMA0/1/3/5/6/7 assigned to
These fields allow you to determine the IRQ/DMA assigned to the ISA
bus and is not available to any PCI slot.
Used MEM base addr
46
MB700 User’s Manual
BIOS SETUP
Select a base address for the memory area used by any peripheral that
requires high memory. The default setting is N/A.
MB700 User’s Manual
47
BIOS SETUP
Load BIOS Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
& EXIT
Load BIOS Defaults
(Y/N)?
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
To load BIOS defaults value to CMOS SRAM, enter “Y”. If not, enter
“N”.
Load Setup Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
& EXIT
Load Setup Defaults
(Y/N)?
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter
“N”.
48
MB700 User’s Manual
BIOS SETUP
Integrated Peripherals
This option sets your hard disk configuration, mode and port.
ROM PCI/ISA BIOS
INTEGRATED PERIPHERALSP
AWARD SOFTWARE INC.
IDE HDD Block Mode
: Enabled
IDE Primary Master PIO
: Auto
Onboard FDC Controller
: Enabled
IDE Primary Slave PIO
IDE Secondary Master PIO
: Auto
Onboard Serial Port 1
: 3F8/IRQ4
: Auto
Onboard Serial Port 2
: 2F8/IRQ3
IDE Secondary Slave PIO
IDE Primary Master UDMA
: Auto
: Auto
UART Mode Select
: Normal
IDE Primary Slave UDMA
: Auto
Onboard Serial Port 3
: Disabled
Onboard Serial Port 4
: Disabled
IDE Secondary Master UDMA : Auto
IDE Secondary Slave UDMA
: Auto
On-Chip Primary PCI IDE
: Enabled
On-Chip Secondary PCI IDE
: Enabled
USB Keyboard Support
: Disabled
Init Display First
: AGP
KBC input clock
: 8 MHz
PWRON After PWR-Fail
: Off
Digital I/O Address
: 260h
ESC : Quit
á â ß : Select Item
Onboard Parallel Port
: 378/IRQ7
F1 : Help
PU/PD/+/- : Modify
Parallel Port Mode
: SPP
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster. Rather
than have the BIOS issue a series of commands that transfer to or from the
disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select the
best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
MB700 User’s Manual
49
BIOS SETUP
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel.
USB Keyboard Support
Select Enabled if your system is using a USB keyboard.
Init Display First
This field allows the system to initialize first the VGA card/hardware
when system is turned on.
KBC input clock
The default setting of the KBC input clock is 8 MHz.
PWRON After PWR-Fail
Enabling this field causes the system to power on by itself when power is
restored, in case the system shuts down due to power failure.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the system board and you wish to use it. If you install an
add-in FDC or the system has no floppy drive, select Disabled in this
field. This option allows you to select the onboard FDD port.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1: 3F8/IRQ4, Serial Port 2: 2F8/IRQ3
Serial Port 3: Disabled, Serial Port 4: Disabled
Parallel Port: 378H/IRQ7
UART Mode Select
This field determines the UART mode in your computer. The settings are
Normal, IrDA and ASKIR. The default value is Normal.
Parallel Port Mode
This field allows you to determine parallel port mode. Settings include
SPP (Standard Printer Port), EPP (Enhanced Parallel Port), and ECP
(Extended Capabilities Port.)
Digital I/O Address
The default value of the digital I/O address is 260h.
50
MB700 User’s Manual
BIOS SETUP
Supervisor / User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password, the
screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted
to enter the password. A message will confirm the password to be
disabled. Once the password is disabled, the system will boot and you can
enter Setup freely.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
HDD LOW LEVEL FORMAT
Enter Password:
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Change / Set / Disable Password
MB700 User’s Manual
51
BIOS SETUP
IDE HDD Auto Detection
This option detects the parameters of an IDE hard disk drive, and
automatically enters them into the Standard CMOS Setup screen.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
HARD DISKS
TYPE
SIZE
CYLS HEAD PRECOMP
LANDZ
SECTOR
MODE
Primary Master:
Select Primary Master Option (N=SKIP) : N
OPTIONS
TYPE
SIZE
1 (Y)
0
0
CYLS HEAD PRECOMP
0
0
0
LANDZ
SECTOR
MODE
0
0
NORMAL
NOTE: Some OSes (like SCO-UNIX) must use ”NORMAL” for installation
ESC: SKIP
Up to four IDE drives can be detected, with parameters for each appearing
in sequence inside a box. To accept the displayed entries, press the “Y”
key; to skip to the next drive, press the “N” key. If you accept the values,
the parameters will appear listed beside the drive letter on the screen.
52
MB700 User’s Manual
BIOS SETUP
Save & Exit Setup
This option allows you to determine whether to accept the modifications
or not. If you type “Y”, you will quit the setup utility and save all changes
into the CMOS memory. If you type “N”, you will return to Setup utility.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
Save to CMOS andSAVE
Exit (Y/N)?
& EXITNSETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Save Data to CMOS & Exit Setup
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
& EXIT
Quit Without Saving
(Y/N)?
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Abandon all Data & Exit Setup
MB700 User’s Manual
53
LAN DRIVERS INSTALLATION
VGA Drivers Installation
This section provides information on how to install the VGA drivers that
come in the floppy diskette with your MB700 board. Please follow the
instructions set forth in this section carefully. Please note that there must
be relevant software installed in your system before you could proceed to
install the VGA drivers. It is recommended that you make a copy of the
VGA driver diskette and put the backup copy in a safe place.
The following items are covered in this section:
Installing the Drivers for Windows 95/98....................................... 55
Installing the Drivers for Windows NT 4.0..................................... 56
54
MB700 User’s Manual
LAN DRIVERS INSTALLATION
Installing the Drivers for Windows 95/98
The following section describes the normal display driver installation
procedures for Windows 95/98. Use the following procedures when
installing the display drivers for Windows 95/98.
1. Click Start, then Settings, then Control Panel.
2. Double click Display.
3. Select the Settings tab, click the Change Display Type button.
4. Click the Change button under Adapter Type.
5. Click the Have Disk button and press OK.
6. Specify the path to the new driver and press <ENTER>:
Example 1: Insert the driver CD in the CD-ROM drive, and enter
d:\vga\ct69000\win95 (assuming D: is the CD-ROM drive.)
Example 2: If you're not sure exactly where the drivers are, click the
Browse button to find them.
7. The Select Device dialog box will appear. Select the hardware that
corresponds to the one you installed in your machine and click OK.
8. Windows 95/98 will copy the display drivers to the proper
directories on your system.
9. Continue by choosing Close. You will be asked to restart your
machine. Do so accordingly.
10. After the system has restarted, you can go back into the Display
applet and select alternate screen resolutions and color depths.
MB700 User’s Manual
55
LAN DRIVERS INSTALLATION
Installing the Drivers for Windows NT 4.0
Once you are in the Windows NT 4.0 environment, follow the procedures
below to install the VGA drivers that come with your board.
1. Click the Start button, then go to Settings and click on Control
Panel.
2. Click on the Display icon to start the Display Properties window.
3. Click on the Settings tab, and then click on Display Type.
4. In the Change Display Type window, click on Change Adapter
Type. This will bring up the Select Device window.
5. In the Change Display window, click on Have Disk. Enter the
directory where the Windows NT driver files are located as
d:\vga\ct69000\winnt40 (assuming D: is the CD-ROM drive.)
Then select OK, or press ENTER.
6. Select Chips Video Accelerator from the display list provided, then
click OK or press ENTER.
7. You will then see a warning panel about Third Party Drivers. Click
on Yes to finish the installation.
8. Once the installation is complete, the system must be shut down and
restarted for the new drivers to take effect.
9. When the system has restarted, the default graphics mode (usually
640x480x256color) has been automatically selected. Click the Start
button, and then go to Settings and click on Control Panel. Click on
the Display icon to start the Display Properties window. Click on
the Settings tab. A new screen setting can be selected using either of
the following methods:
A. Use the slide-bar in the Desktop Area to select new setting.
B. Click on List All Modes. From the list provided, select a
new setting, then click OK or press ENTER.
C. Click on Test to test the newly selected graphics mode.
Follow the instructions given on screen. A test screen
should appear, followed by the Testing Mode window.
Click on Yes to continue. Click on Apply to switch to the
new graphics mode. Graphics modes are changed
dynamically on NT 4.0, so you do not need to shut down and
restart for the new screen settings to work.
56
MB700 User’s Manual
LAN DRIVERS INSTALLATION
LAN Drivers Installation
This section describes LAN features and driver installation of the Intel
82559 Ethernet function available with the IBD99 or IBD59 MicroPCI
card.
The following items are covered in this section:
Introduction....................................................................................... 58
Making Floppy Disks for NetWare and Windows Installation....... 58
Installing LAN Drivers for Windows 95......................................... 59
Installing LAN Drivers for Windows 98......................................... 59
Installing LAN Drivers for Windows NT........................................ 60
MB700 User’s Manual
57
LAN DRIVERS INSTALLATION
Introduction
Intel 82559 a 32-bit 10/100MBps Ethernet controller for PCI local
bus-compliant PCs. It supports bus mastering architecture, and
auto-negotiation feature that can be used for both 10Mbps and 100Mbps
connection.
Making Floppy Disks for NetWare and Windows
Installation
You need to use a floppy disk to install the LAN drivers. Use the
MAKEDISK.BAT utility located in the \LAN\I8255X\MAKEDISK
directory on the CD.
MAKEDISK [operating system] [destination]
where [operating system] is the OS for which you are creating the
diskette, and [destination] is the drive letter and path (such
as A:). If no destination is specified, the A: drive will be used.
The possible [operating system] options are:
NT = Microsoft Windows NT
W2K = Microsoft Windows* 2000
W9X = Microsoft Windows* 95 and Windows 98
NW = Novell NetWare servers and clients
DOS = Microsoft DOS and IBM OS2
Make sure you have a 1.44 MB formatted, non-bootable diskette in the
floppy drive when using this utility.
NOTE: The utility MUST be run from the \LAN\I8255X \MAKEDISK
directory.
Alternately, you can use the following .BAT files (located
in the root directory on this CD) to simplify this process:
MAKEW9X.BAT -- Creates a drivers disk for Windows 95 and
Windows 98.
MAKENT.BAT -- Creates a drivers disk for Windows NT.
MAKEW2K.BAT -- Creates a drivers disk for Windows 2000.
MAKENW.BAT -- Creates a drivers disk for Novell NetWare
servers and clients.
58
MB700 User’s Manual
LAN DRIVERS INSTALLATION
Installing LAN Drivers for Windows 95
Follow these steps to install the Intel 82559 LAN/Ethernet driver for
Windows 95:
1. From the Control Panel, double-click the System icon.
2. Click the Device Manager tab.
3. Double-click Other Devices (question mark icon) in the list area.
4. Double-click a PCI Ethernet Controller.
5. Click the Driver tab, then click Update Driver.
6. Insert the Configuration and Drivers disk or CD in the appropriate
drive, and at the Update Device Driver Wizard, select "No" and
click Next.
7. Click Have Disk, insert the Configuration and Drivers disk
in the appropriate drive, and click OK.
8. At the Select Device dialog box, click OK again.
9. Follow any prompts for Windows 95 installation disks and restart
when prompted.
Note: The Windows 95 system files are typically available on the
Windows 95 CD in the win95 directory (D:\win95).
Installing LAN Drivers for Windows 98
Follow these steps to install the Intel 82559 LAN/Ethernet driver for
Windows 95:
1. From the Control Panel, double-click the System icon.
2. Click the Device Manager tab.
3. Double-click Other Devices or Network Adapters in the list area.
4. Double-click a PCI Ethernet Controller.
5. Click the Driver tab, then click Update Driver.
6. Click Next at the Update Device Driver Wizard.
7. Select "Display a list of all the drivers..." and click Next.
8. Insert the Intel adapter disk and click Have Disk.
9. Enter the appropriate drive for your disk media (A:) and click OK.
10. Click OK at the Select Device dialog box.
11. The Update Wizard displays the message that it has found the driver.
Click Next.
12. Click Finish.
13. Restart your computer when prompted.
MB700 User’s Manual
59
LAN DRIVERS INSTALLATION
Installing LAN Drivers for Windows NT
Note: It is recommended that you install the latest Service Pack for
Windows NT 4.0, available through Microsoft.
Follow the instructions below to configure it the Ethernet hardware
under Windows NT.
1. Double-click the Network icon in the Control Panel.
2. Select the Adapter tab.
3. Click Add. You'll see a list of adapters.
4. Don't select an adapter from this list. Instead, insert the
Intel adapter disk or CD into the appropriate drive and click
Have Disk.
5. Enter the appropriate drive for your disk media (A:)
and click OK. Then follow the prompts to complete installation.
When the adapter is added you'll see a new adapter listed in the
Network adapters list.
6. Click Close to finish and configure any protocols as prompted.
7. Restart Windows NT when prompted.
60
MB700 User’s Manual
AUDIO DRIVERS INSTALLATION
Audio Drivers Installation
This section provides information on how to install the audio drivers for
ESS Solo-1 ES1938S that come in floppy diskettes with your MB700
board. Please follow the instructions set forth in this section. It is
recommended that you make a copy of the drivers and put the backup
copy in a safe place.
The following items are covered in this section:
Installing the Audio Driver for Windows 95 .................................. 62
Installing the Audio Driver for Windows 98 .................................. 63
Installing the Audio Driver for Windows NT ................................. 64
MB700 User’s Manual
61
AUDIO DRIVERS INSTALLATION
Installing the Audio Driver for Windows 95
1.
2.
3.
4.
Turn on the computer and start Windows 95.
Insert the CD containing the ESS Solo-1 ES1938S audio drivers for
Windows 95.
The CD autoruns and shows a screen with options for you to choose.
Click on Sound and select ESS Solo-1 to install the audio software
and drivers. The welcome screen is then displayed.
Click the Next button to continue the installation process. When the
ESS Solo-1 Installation window appears, select Upgrade Drivers
and click the Next button.
5. After file copying is done, restart Windows 95.
6. When Windows restart, it will detect a PCI Multimedia Audio
Device. Insert the audio driver CD and click the Next button to start
file copying, then click Finish.
7. When prompted to insert the Windows 95 CD, do accordingly and
click OK. Key in the path (for example, d:\win95) where the
Windows 95 files are located and click OK. The installation is
complete.
62
MB700 User’s Manual
AUDIO DRIVERS INSTALLATION
Installing the Audio Driver for Windows 98
1.
2.
3.
4.
Turn on the computer and start Windows 98.
Insert the diskette containing the ESS Solo-1 ES1938S audio drivers
for Windows 98.
The CD autoruns and shows a screen with options for you to choose.
Click on Sound and select ESS Solo-1 to install the audio software
and drivers. The welcome screen is then displayed.
Click the Next button to continue the installation process. When the
ESS Solo-1 Installation window appears, select Upgrade Drivers
and click the Next button.
5. After file copying is done, restart Windows 98.
6. When Windows restarts, it will detect a PCI Multimedia Audio
Device. Insert the audio driver CD and click the Next button. Click on
the Search for the best driver checkbox, then click Next. Now
install The Update driver, ESSSolo-1 PCI Audio Device. Click Next
and then Next again to start file copying. After file copying is done,
click Finish
7. Now, Windows detects a new hardware which is the gameport
joystick. Click OK and insert the Windows 98 CD and key in the path
(for example, d:\win98) where the Windows 98 files are located and
click OK. The installation is complete.
MB700 User’s Manual
63
AUDIO DRIVERS INSTALLATION
Installing the Audio Driver for Windows NT
1.
2.
3.
4.
Turn on the computer and start Windows NT.
Insert the diskette or CD containing the ESS Solo-1 ES1938S audio
drivers for Windows NT.
The CD autoruns and shows a screen with options for you to choose.
Click on Sound and select ESS Solo-1 to install the audio software
and drivers. The welcome screen is then displayed.
Click the Next button to continue the installation process. When the
ESS Solo-1 Installation window appears, select Upgrade Drivers
and click the Next button.
5. When the Choose Driver Language window appears, choose
English and click the Next button to start file copying. After file
copying is done, click Finish to restart Windows NT and for changes
to take effect.
64
MB700 User’s Manual
APPENDIX
Appendix
A. I/O Port Address Map
B. Interrupt Request Lines (IRQ)
C. Memory Mapping
MB700 User’s Manual
65
APPENDIX
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses
which also becomes the identity of the device. The following table lists
the I/O port addresses used on the Industrial Motherboard.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278 - 27F
2F8h - 2FFh
2B0 - 2DF
378h - 3FFh
360 - 36F
3B0 - 3BF
3C0 - 3CF
3D0 - 3DF
3F0h - 3F7h
3F8h - 3FFh
66
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
MB700 User’s Manual
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on MB700.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2/#4
Serial Port #1/#3
Parallel Port
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
MB700 User’s Manual
67
APPENDIX
C. Memory Mapping
(1MB)
100000
FFFFF
F0000
EFFFF
ONBOARD DRAM
SYSTEM BIOS
}
Memory address E0000-EFFFF
E0000
may be free after BIOS boot
DFFFF
FREE
D0000
CFFFF
FREE
CC000
CBFFF
VIDEO BIOS
C0000
BFFFF
VIDEO RAM
A0000
9FFFF
ONBOARD DRAM
0-640K
0
68
MB700 User’s Manual