Mitsubishi Electric 840 Series Installation manual

JY997D51601B
Side
B
Side
JAPANESE
Side
ENGLISH
A
B
1. Outline
2.1 When Installing the Display Module Directly to the Main Unit
The FX3S-5DM display module (hereinafter called display module) is installed to the
FX3S Series main unit or expansion board to monitor/change device states and values.
1) Remove the top cover (A in the figure
on the right).
Item
1)
1.1 Incorporated Items
Product
FX3S-5DM display module
Included items
Manual Number
JY997D51601
Revision
B
Date
October 2014
Installation Manual (This manual)
[5]
[4]
This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and the manuals of all relevant
products fully to acquire proficiency in handling and operating the product. Make
sure to learn all the product information, safety information, and precautions.
Store this manual in a safe place so that it can be taken out and read whenever
necessary. Always forward it to the end user.
Registration:
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
[3]
Effective October 2014
Specifications are subject to change without notice.
2014 MITSUBISHI ELECTRIC CORPORATION
No.
Safety Precaution (Read these precautions before use.)
This manual classifies the safety precautions into two categories:
and
.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on the circumstances, procedures indicated by
also cause severe injury.
It is important to follow all precautions for personal safety.
may
Associated Manuals
Manual name
FX3S Series
User’s Manual
- Hardware Edition
Manual No.
Description
JY997D48601
MODEL CODE:
09R535
Explains the FX 3S Series PLC
specifications for I/O, wiring,
installation, and maintenance.
How to obtain manuals
For product manuals or documents, consult with the Mitsubishi Electric dealer
from who you purchased your product.
Applicable standards
FX3S-5DM comply with the EC Directive (EMC Directive). Further information can
be found in the following manual.
FX3S Series User's Manual - Hardware Edition
Attention
 This product is designed for use in industrial applications.
Note
 Manufactured by: Mitsubishi Electric Corporation
2-7-3 Marunouchi, Chiyoda-ku, Tokyo, 100-8310 Japan
 Manufactured at: Mitsubishi Electric Corporation Himeji Works
840 Chiyoda-machi, Himeji, Hyogo, 670-8677 Japan
 Authorized Representative in the European Community:
Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany
[1]
35 (1.38")
9.6 (0.38")
12 (0.48")
Description
[1]
"OK" button
Use to choose the item, set the value, etc.
[2]
"+" button
Use to move cursor or set the value.
[3]
"-" button
Use to move cursor or set the value.
[4]
"ESC" button
Use to cancel operation or return to previous screen.
[5]
Display
Displays current time and monitored status of device.
[6]
Connector for
PLC
Used to connect display module to PLC.
[7]
Display module
fixing hook
Used to fix display module to PLC.
(When used together with an expansion board)
2. Installation
INSTALLATION
PRECAUTIONS
 Make sure to cut off all phases of the power supply externally before attempting
installation or wiring work.
Failure to do so may cause electric shock or damage to the product.
INSTALLATION
PRECAUTIONS
 Use the product within the generic environment specifications described in PLC
main unit manual (Hardware Edition).
Never use the product in areas with excessive dust, oily smoke, conductive dusts,
corrosive gas (salt air, Cl 2 , H 2 S, SO 2 , or NO 2 ), flammable gas, vibration or
impacts, or expose it high to temperature, condensation, or rain and wind.
If the product is used in such conditions, electric shock, fire, malfunctions,
deterioration or damage may occur.
 Do not touch the conductive parts of the product directly.
Doing so may cause device failures or malfunctions.
 Connect the display module securely to the appropriate connector.
Loose connections may cause malfunctions.
The following section describes the installation method for the FX3S Series PLC
(FX3S-30M. In this example).
Turn off the power to the PLC before installation.
For more details on removal and installation, refer to the PLC main unit manual.
FX3S Series User's Manual - Hardware Edition
Specifications
Display device
TN monochrome liquid crystal display
Display character
Seven-segment display + icon display
Backlight
Green LED backlight
Button
4 operation buttons (ESC, -, +, and OK)
4. Function List
[7]
MASS (Weight): Approx. 20 g (0.05 lbs)
Name
2)
[6]
Cut off this part when
using an expansion board
at the same time.
[2]
B
Unit: mm (inches)
34.4 (1.36")
INSTALLATION MANUAL
2) Make sure the display module (B in the
figure on the right) is in parallel with the
main unit and attach it to the optional
equipment connector.
1.2 External Dimensions and Part Names
51.2 (2.02")
FX3S-5DM
3.3 Display Specifications
A
2.2 When Using the Display Module Together with an Expansion
Board
Assuming that the expansion board is attached to the main unit.
The connector cover for the expansion board is removed.
To attachment of the expansion board, refer to the following manual.
FX3S Series User's Manual - Hardware Edition
1) Cut off part A shown in the right figure
(display module).
Caution:
When part A is cut off, the display
module can not be installed to the main
unit directly.
The functions of a display module are listed as follows:
For details on the functions, refer to the following manuals.
FX3S Series User's Manual - Hardware Edition
 Monitor/Test
 Clock display and setting
 Operation button ON/OFF information
 Display screen protect function
 Specified device monitor function
 Back light off function
 Error display valid/invalid
 Decimal/hexadecimal current value display setting
A
2)
B
2) Make sure the display module is in
parallel with the main unit and attach it
to the optional equipment connector (B
in the figure on the right).
3. Specifications
STARTUP AND
MAINTENANCE
PRECAUTIONS
 Do not disassemble or modify the PLC.
Doing so may cause fire, equipment failures, or malfunctions.
* For repair, contact your local Mitsubishi Electric representative.
 Do not drop the product or exert strong impact to it.
Doing so may cause damage.
DISPOSAL
PRECAUTIONS
 Please contact a certified electronic waste disposal company for the
environmentally safe recycling and disposal of your device.
TRANSPORTATOION AND
STORAGE PRECAUTIONS
 The product is a precision instrument. During transportation, avoid impacts larger
than those specified in the general specifications by using dedicated packaging
boxes and shock-absorbing palettes.
Failure to do so may cause failures in the product.
After transportation, verify operation of the product and check for damage of the
mounting part, etc.
3.1 Applicable PLC
Model name
FX3S Series PLC
Applicability
Ver. 1.20 or later
 Only one display module can be used per main unit.
For details on the system configuration, refer to the following manual.
FX3S Series User's Manual - Hardware Edition
3.2 General Specifications
The general specifications are equivalent to the PLC main unit.
For general specifications, refer to the following manuals.
FX3S Series User's Manual - Hardware Edition
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
 This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
 Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
 This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
HIMEJI WORKS : 840, CHIYODA MACHI, HIMEJI, JAPAN