Electrolux E30MO65GSSA Service manual

ELECTROLUX
SERVICE MANUAL
E30MO65GSSA
S37M276E30S06
MICROWAVE OVEN
MODEL
E30MO65GSSA
In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified should
be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current. Contact with the following parts may result in a severe, possibly fatal, electrical shock. (Inverter unit that includes
High Voltage Capacitor, High Voltage Power Transformer, High Voltage Rectifier and Heat sink etc., and Magnetron, High
Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY..................... INSIDE FRONT COVER
BEFORE SERVICING ....................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL................................................................................................................. 4
MICROWAVE MEASUREMENT PROCEDURE..................................................................................................... 5
FOREWORD AND WARNING ............................................................................................................................... 7
PRODUCT SPECIFICATIONS ............................................................................................................................... 8
GENERAL INFORMATION.................................................................................................................................... 8
OPERATION......................................................................................................................................................... 0
TROUBLESHOOTING GUIDE ............................................................................................................................. 6
TEST PROCEDURE ............................................................................................................................................ 8
TOUCH CONTROL PANEL ASSEMBLY .............................................................................................................. 25
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE................................................................. 3
PICTORIAL DIAGRAM ......................................................................................................................................... 38
LSI UNIT CIRCUIT ............................................................................................................................................... 39
PRINTED WIRING BOARD.................................................................................................................................. 40
PARTS LIST ........................................................................................................................................................ 4
PACKING AND ACCESSORIES .......................................................................................................................... 46
This document has been published to be used for aftersales service only. The contents are subject to change without notice.
ElEctrolux HoME ProDuctS, INc.
P. O. Box 212378, Augusta, GA, 30917
800•944•9044
Publication # 5995505368
P/N 316439254
E30MO65GSSA
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO
EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave
source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing
surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of
dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and
connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and
transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before
the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be performed
on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact Electrolux HOME PRODUCTS,
INC. immediately.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven and 2)
contact Electrolux HOME PRODUCTS, INC. and Food and Drug Administration's Center for Devices
and Radiological Health immediately.
Service personnel should inform Electrolux HOME PRODUCTS, INC. of any certified unit found with
emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit until the
oven has been brought into compliance.
DANGER CAUTION
HIGH VOLTAGE
Do not energize a microwave oven with the outer case cabinet removed, because a microwave oven generates High Voltage in the circuit.
If you intend to operate the oven employing the high frequency switching power converter circuit, you should
take special precautions to avoid an electrical shock hazard.
The high voltage transformer, high voltage capacitor and high voltage diode have energized high voltage
potential approx. 8 KV.
The aluminium heat sink is connected to the switching power transistor Collector pole, and has an energized
high voltage potential approx. 650V peak.
DO NOT ACCESS THE high voltage transformer, high voltage capacitor, high voltage diode and HEAT SINK WHEN THE POWER SUPPLY IS CONNECTED TO AN ELECTRICAL
OUTLET.
E30MO65GSSA
Notes
E30MO65GSSA
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power
Transformer, Magnetron, High Voltage Rectifier
Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
Before Servicing
1. Disconnect the power supply cord remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case
is installed.
7. Run the oven and check all functions.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case
is installed.
4. Run the oven and check all functions.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for
60 seconds and then short-circuit the connection of the
high-voltage capacitor (that is the connecting lead of the
high-voltage rectifier) against the chassis with the use of
an insulated screwdriver.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water remains
cold carry out Before Servicing procedure and re-examine
the connections to the component being tested.
Whenever troubleshooting is performed the power supply
must be disconnected. It may in, some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation
tape.
6. After that procedure, reconnect the power supply cord.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and a microwave leakage test should be carried out.
When the testing is completed,
1. Disconnect the power supply cord, and then remove
E30MO65GSSA
MICROWAVE MEASUREMENT PROCEDURE (CANADA)
After adjustment of the door switches are completed individually or collectively, switch test and microwave leakage test
must be performed with survey instrument and test result must be confirmed to meet the requirement of the performance
standard
for microwave ovens as undermentioned.
A. Requirements:
Every microwave oven shall function in such a manner that when the oven is fully assembled and operating with its
service
controls and user controls adjusted to yield the maximum output, the leakage radiation, at all points at least 5 cm. from
the
external surface of the oven, does not exceed:
1) 1.0mW/cm2 with the test load of 275 ± 15 ml of water at an initial temperature 20 ±5oC.
2) 5.0mW/cm2 when the outer enclosure is removed with a test load of 275 ± 15 ml of water at an initial temperature
20±5oC.
3) 5.0mW/cm2 without a test load.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by CSA and NHW performance standard for microwave ovens must be used for testing recommended instruments are , NARDA 8100 and NARDA 8200.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml of tap water initially at 20±5oC in the center of the oven cavity.
The water container shall be a low form of 600 ml beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and made
of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode, Close the door and select a cook cycle of several minutes. If the
water begins to boil before the survey is completed, replace it with 275 ml of cool water.
C. Leakage test with enclosure installed :
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the
oven.
2) Move the probe slowly, not faster than 2.5 cm/sec. along the gap, watching for the maximum indication on the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the
metal has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the
closed latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
C. Leakage test without enclosure:
1) Remove the enclosure (cabinet).
2) Grasp the probe of the survey instrument and hold it perpendicular to all mechanical and electric parts of the oven that
is accessible to the user of the oven including, but not limited to, the waveguide, cavity seams, magnetron gap between
the door and the body of the oven.
3) Move the probe slowly, not faster than 2.5 cm/sec. along the gap, watching for the maximum indication on the meter.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is under 5mW/cm2.
CAUTION: Special attention should be given to avoid electrical shock because HIGH VOLTAGE is generated during this
test
No Load test
1) Operate the oven without a load and measure the leakage by the same method as the above test procedure
" Leakage test with enclosure installed"
2. Make sure that the highest leakage should not exceed 5mW/cm2.
NOTE: After servicing, record data on service invoice and microwave leakage report.
E30MO65GSSA
MICROWAVE MEASUREMENT PROCEDURE (USA)
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave
oven should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to
acquisition by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more
from the external surface of the oven.
2) Safety interlock switches:
Primary interlock relay switch shall prevent microwave radiation emission in excess of the requirement as above
mentioned. Secondary interlock relay and door sensing switch shall prevent microwave radiation emission in excess
of
5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5O C (68OF) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement):
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the
oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the
metal has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door, pull the door away from the front of the oven as far as is permitted by the
closed latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the primary interlock switch/secondary interlock relay does turn the oven OFF before any door movement.
E30MO65GSSA
SERVICE MANUAL
ELECTROLUX
PRODUCT DESCRIPTION
MICROWAVE OVEN
E30MO65GSSA
GENERAL INFORMATION
FOREWORD
This Manual has been prepared to provide Electrolux Home Products
Service Personnel with Operation and Service Information for the ELECTROLUX MICROWAVE OVEN, E30MO65GSSA.
OPERATION
It is recommended that service personnel carefully study the entire text of
this manual so that they will be qualified to render satisfactory customer
service.
TROUBLESHOOTING GUIDE AND
TEST PROCEDURE
Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and microwave radiation
hazard.
TOUCH CONTROL PANEL
WARNING
Never operate the oven until the following points are ensured:
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
COMPONENT REPLACEMENT
AND ADJUSTMENT PROCEDURE
WIRING DIAGRAM
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
PARTS LIST
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service personnel - Do not contact the following parts while the appliance is
energized;
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened or
removed.
Electrolux HOME PRODUCTS, INC.
E30MO65GSSA
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements 120 Volts (USA) / 117 Volts (Canadian)
13.0 Amperes (Microwave) / 13.0 Amperes (Convection)
60 Hertz / Single phase, 3 wire grounded
Power Output 900 watts (IEC 705 Test Procedure)
Operating frequency of 2450MHz
Convection Power Output 1450 Watts
Case Dimensions Width 24-5/8"
Height 14-7/8" Depth 19"
Cooking Cavity Dimensions
(1.5 Cubic Feet )
Width 16-1/8"
Height 9-5/8"
Depth 16-1/8"
Control Complement Touch Control System
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI............................................ Full power throughout the cooking time
P-90............................................................... approx. 90% of Full Power
P-80............................................................... approx. 80% of Full Power
P-70............................................................... approx. 70% of Full Power
P-60............................................................... approx. 60% of Full Power
P-50............................................................... approx. 50% of Full Power
P-40................................................................ approx. 40% of Full Power
P-30 .............................................................. approx. 30% of Full Power
P-20............................................................... approx. 20% of Full Power
P-10................................................................ approx. 10% of Full Power
P-0............................................... No power throughout the cooking time
Convection Temperature for Variable Cooking
CONVECTION................................................ 100 - 450οF Temp. control
LOW MIX. BAKE................................ 350οF with 10% microwave power
HIGH MIX. ROAST............................. 300οF with 30% microwave power
SLOW COOK........................................... 300οF for 4 hours (no preheat)
BROIL............................................................................. 450οF (preheat)
Oven Cavity Light
Safety Standard
Help pad, Reheat pad, Add-A-Minute pad, Popcorn pad
Defrost pad, Sensor Cook pad, Convec Broil pad
High Mix Roast pad, Convec Bake pad, Low Mix Bake pad
Broil pad, Slow Cook pad, Preheat pad.
Number and temperature selection pads, Timer pad, Clock pad
Stop/Clear pad, Power Level pad, Start / Touch On pad
Yes
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
Canadian Standards Association.
Health CANADA, Industry CANADA.
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the
electric current.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
E30MO65GSSA
Electrical Requirements
The electrical requirements are a 115 -120 volt 60 Hz, AC only,
15 or more amp. fused electrical supply. It is recommended that a separate circuit serving only this appliance be provided. When installing this
appliance, observe all applicable codes and ordinances.
A short power-supply cord is provided to reduce risks of becoming
entangled in or tripping over a longer cord.
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified electrician and have it replaced with a properly grounded three-pronged wall
receptacle or have a grounding adapter properly grounded and polarized. If an extension cord must be used, it should be a 3-wire, 15 amp.
or more cord. Do not drape over a countertop or table where it can be
pulled on by children or tripped over accidentally.
3-Pronged Plug
Grounded
Receptacle Box
Grounding Pin
3-Pronged Receptacle
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM
THIS PLUG.
OVEN DIAGRAM
7
1
3
5
10
12
9
13
4
8
11
6
1.
2.
3.
4.
5.
15
6
14
TOUCH CONTROL PANEL
2
Ventilation openings. (Rear side)
Oven door with see-through window.
Oven lamp.
Turntable support.
Removable turntable.
The turntable will rotate clockwise or
counterclockwise.
6. Safety door latches.
The oven will not operate unless the door is
securely closed.
7. Wave guide cover.
8. Door open button.
9. Auto-Touch control panel.
10. Lighted digital display.
11. Convection air openings.
12. Removable low rack. (Broiling trivet)
13. Removable low rack. (Baking rack)
14. Turntable motor shaft.
15. Power supply cord.
E30MO65GSSA
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
The following is a description of component functions during oven operation.
door switch, monitor switch, door sensing switch, the
secondary interlock relay and the primary interlock switch
are activated with the following results. The circuits to
the turntable motor, the cooling fan motor, and the high
voltage components are de-energized, the oven lamp
remains on, and the digital read-out displays the time
still remaining in the cook cycle when the door was
opened.
7. The monitor switch is electrically monitoring the operation
of the relay (RY1) and the primary interlock switch and
is mechanically associated with the door so that it will
function in the following sequence.
(1)When the door opens from a closed position, the door
sensing switch and the primary interlock switch open
their contacts, and then the monitor switch contacts
close and then the third door switch contacts open.
(2)When the door is closed from the open position, the
monitor switch contacts open and the third door switch
contacts close first, and then the contacts of the primary
interlock switch and the door sensing switch close.
If the relay (RY1) and the primary interlock switch fail with
their contacts closed when the door is opened, the closing of
the monitor switch contacts will form a short circuit through
the monitor fuse, the relay (RY1) and the primary interlock
switch, causing the monitor fuse to blow.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 117 volts A.C. is supplied to the
control unit. (Figure O-1).
1. The display will show "WELCOME, PRESS CLEAR".
To set any program or set the clock, you must first touch
the STOP/CLEAR pad. The display will clear, and " : "
will appear.
NOTE: When the door is opened, the oven lamp comes
on.
2. A signal is input to the control unit, energizing the coil
of shut-off relay (RY-4). RY4 contacts close, completing
a circuit to the damper motor. The damper motor now
operates moving the damper to the open position, thereby
closing the contacts of the damper switch inputs a signal
to the control unit. The coil of relay RY-4 is de-energized,
opening its contacts, thereby turning off the damper
motor.
COOKING CONDITION
POWER LEVEL P-0 TO P-90 COOKING
Program desired cooking time Variable Cooking Control
by touching the NUMBER pads and the power level pad.
When the START pad is touched, the following operations
occur:
When Variable Cooking Power is programmed, the 117
volts A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY-2). RY-2 is operated by the
control unit within an varying time base. Microwave power
operation is as follows:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY CONNECTED COMPONENTS
RY-1 Oven lamp/Turntable motor
RY-2 Power transformer
RY-3
Heating element
RY-4
Damper motor
RY-5
Convevtion motor
RY-6
Fan motor
VARI-MODE ON TIME OFF TIME
Power 10(P-HI) 32 sec. 0 sec.
(100% power)
Power 9(P-90)
30 sec. 2 sec.
(approx. 90% power) Power 8(P-80)
26 sec. 6 sec.
(approx. 80% power)
Power 7(P-70)
24 sec. 8 sec.
(approx. 70% power) Power 6(P-60)
22 sec. 10 sec.
(approx. 60% power) Power 5(P-50)
18 sec. 14 sec.
(approx. 50% power)
Power 4(P-40)
16 sec. 16 sec.
(approx. 40% power)
Power 3(P-30)
12 sec. 20 sec.
(approx. 30% power)
Power 2(P-20)
8 sec. 24 sec.
(approx. 20% power)
Power 1(P-10)
6 sec. 26 sec.
(approx. 10% power)
Power 0(P-0)
0 sec. 32 sec.
(0% power)
2.117 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3 volts A.C.
output on the filament winding, and approximately 2360
volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron
filament and the H.V. winding voltage is sent to a voltage
doubler circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed
to be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
6. When the door is opened during a cook cycle, third
Note: The ON/OFF time ratio does not correspond with the
percentage of microwave power, because approx. 2
10
E30MO65GSSA
CONVECTION COOKING CONDITION
first. And then program desired cooking time by touching
the Number pads. The LOW MIX/BAKE pad is preprogrammed for 350οF with 10% microwave power, while the
HIGH MIX/ROAST pad is preprogrammed for 300οF with
30% microwave power. When the START pad is touched,
the following operations occur:
1. The numbers on the digital read-out start to count down
to zero.
2. The shut-off relays (RY1,RY2,RY3,RY5 and RY6) are
energized, turning on the oven lamp, turntable motor,
cooling fan motor and convection fan motor.
3. The shut-off relay (RY4) is energized.
The damper door is closed from the open position.
4. The heater relay (RY3) is energized, applying the main
supply voltage to the heating element.
5. Now, the oven is in the convection cooking condition.
6. When the oven temperature reaches the selected
temperature, the following operations occur:
6-1.The power supply voltage is alternated to the heating
element and power transformer.
6-2.The heating element operates through the heater
relay (RY3) contacts and the power transformer
operates through the primary interlock relay (RY2)
contacts.
6-3.These are operated by the control unit to supply
alternately within a 32 second time base, convection
heat and microwave energy.
PREHEATING CONDITION
Program desired convection temperature by touching the
CONVECTION pad and the Temperature pad.
When the START pad is touched, the following operations
occur:
1. The coil of shut-off relays (RY1, RY3,RY5 and RY6) are
energized, the oven lamp, cooling fan motor, turntable
motor and convection motor are turned on.
2. The coil of relay (RY4) is energized by the control unit.
The damper is moved to the closed position, opening
the damper switch contacts. The opening of the damper
switch contacts sends a signal to the LSI on the control
unit de-energizing the relay (RY4) and opening the circuit
to the damper motor.
3. The coil of heater relay (RY3) is energized by the control
unit and the main supply voltage is applied to the heating
element.
4. When the oven temperature reaches the selected preheat
temperature, the following operations occur:
4-1 The heater relay is de-energized by the control unit
temperature circuit and thermistor, opening the circuit
to the heating element.
4-2.The oven will continue to function for 30 minutes,
turning the heater on and off, as needed to maintain
the selected preheat temperature. The oven will
shut-down completely after 30 minutes
The relationship between the convection and microwave
power operations are as follows.
Note: The ON and OFF time ratio does not correspond
with the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
CONVECTION COOKING CONDITION
When the preheat temperature is reached, a beep signal
will sound indicating that the holding temperature has been
reached in the oven cavity. Open the door and place the
food to be cooked in the oven.
Touch the CONVEC pad first and then touch the Temperature pad. And program desired cooking time by touching
the Number pads.
When the START pad is touched, the following operations
occur:
1. The numbers on the digital read-out start to count down
to zero.
2. The oven lamp, turntable motor, cooling fan motor and
convection motor are energized.
3. Heater relay (RY3) is energized (if the cavity temperature
is lower than the selected temperature) and the main
supply voltage is applied to the heating element to return
to the selected cooking temperature.
4. Upon completion of the cooking time, the audible signal
will sound, and oven lamp, turntable motor, cooling fan
motor and convection motor are de-energized. At the
end of the convection cycle, if the cavity air temperature
is above 275οF, the circuit to RY6 will be maintained (by
the thermistor circuit) to continue operation of the cooling
fan motor until the temperature drops below 245οF, at
which time the relay will be de-energized, turning off the
fan motor. Relay RY5 will however, open as soon as the
convection cycle has ended, turning off the convection
fan motor.
5. At the end of the convection cook cycle, shut-off relay
(RY4) is energized turning on the damper motor. The
damper is returned to the open position, closing the
damper switch contacts which send a signal to the control
unit, de-energizing shut-off relay (RY4).
6 SEC.
26 SEC.
ON
(MICRO.)
MICROWAVE POWER
= APPROX. 10%
OFF
(CONVEC.)
LOW MIX
BAKE
12 SEC.
CONVECTION
TEMPERATUE
= 350°F (180°C)
20 SEC.
ON
(MICRO.)
OFF
MICROWAVE POWER
= APPROX. 30%
ON
(CONVEC.)
OFF
32 SEC.
HIGH MIX
ROAST
CONVECTION
TEMPERATUE
= 300°F
Note: During alternate Microwave/Convection operation,
the convection heater is energized only if the cavity
temperature drops below the set temperature.
SENSOR COOKING CONDITION
Using the SENSOR COOK function, the foods are cooked
without figuring time, power level or quantity. When the oven
senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining
cooking time and power level needed for best results.
When the food is cooked, water vapor is developed.
The sensor “senses” the vapor and its resistance increases
AUTOMATIC MIX COOKING CONDITION
Touch the HIGH MIX/ROAST or the LOW MIX/BAKE pad
11
E30MO65GSSA
5. When the oven temperature has reached the programmed
convection temperature, the oven goes into the
programmed cooking mode.
6. At the end of the COMPU BROIL/ ROAST/ BAKE cycle,
the damper is returned to the open position and the oven
will go to the off condition. The cooling fan will remain
on until the oven has cooled.
gradually. When the resistance reaches the value set according to the menu, supplementary cooking is started.
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
An example of how sensor works:
1. P o t a t o e s
at
room
temperature.
Vapor is emitted very slowly.
COMPU DEFROST COOKING
MIC
2. Heat potatoes. Moisture and
humidity is emitted rapidly.
You can smell the aroma as
it cooks.
3. Sensor detects moisture
and humidity and calculates
cooking time and variable
power.
RO
AH SENSOR
The COMPU DEFROST key is a special function key to defrost meats and poultry faster and better. COMPU DEFROST
automatically defrosts roast beef, etc.. When the COMPU
DEFROST is selected and the food weight is entered by
using the COMPU DEFROST pad, the oven will cook according to the special cooking sequence.
MIC
WA
RO
VE
FIRE SENSING FEATURE (MICROWAVE MODE)
WA
VE
This model incorporates a sensing feature which will stop
the oven's operation if there is a fire in the oven cavity during microwave cooking.
This is accomplished by the LSI repeatedly measuring
the voltage across the temperature measurement circuit
(thermistor) during it's 32-seconds time base comparing the
obtained voltage measurements. If the most recent voltage measured is 300mV greater than the previous voltage
measured, the LSI judges it as a fire in the oven cavity and
switches off the relays to the power transformer, fan motor
and convection motor. The LSI also stops counting down
and closes the damper door so that no fresh air will enter
the oven cavity. Please refer to the following section for a
more detailed description.
Operation
Please refer to the timing diagrams below.
1. The thermistor operates within a 32-seconds time
base and it is energized for three (3) seconds and off
for 29 seconds. Two (2) seconds after the thermistor
is energized, the voltage across the temperature
measurement circuit is sampled by the LSI and twenty
one (21) seconds after the thermistor is cut off the LSI
turns on the cooling fan for six (6) seconds.
2. The above procedure is repeated. If the difference
between the first voltage measured (in step 1) and the
voltage measured when the procedure is repeated (step
2) is greater than 300mV the LSI makes the judgment
that there is a fire in the oven cavity and will switch
off the relays to the power transformer, fan motor and
convection motor. The LSI also stops counting down and
closes the damper door so that no fresh air will enter the
oven cavity.
3. Once the fire sensor feature has shut the unit down, the
programmed cooking cycle may be resumed by pressing
the "START" pad or the unit may be reset by pressing
the "CLEAR" pad.
Cooking Sequence.
1. Touch SENSOR COOK pad.
NOTE: The oven should not be operated on SENSOR
COOK immediately after plugging in the unit. Wait
two minutes before cooking on SENSOR COOK.
2. Select desired Sensor setting.
3. Touch START pad.
The coil of shut-off relay (RY1, RY6) is energized, the
oven lamp and cooling fan motor are turned on, but the
power transformer is not turned on.
4.After about 16 seconds, the cook relay (RY-2) is energized.
The power transformer is turned on, microwave energy
is produced and first stage is started. The 16 seconds
is the cooling time required to remove any vapor from
the oven cavity and sensor.
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
5. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero. At this time, the
door may be opened to stir food, turn it or season, etc.
6. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and
the power transformer, oven lamp, etc. are turned off.
7. Opening the door or touching the STOP/CLEAR pad, the
time of day will reappear on the display and the oven will
revert to an OFF condition.
COMPU BROIL/ COMPU ROAST/ COMPU BAKE
COMPU BROIL/ ROAST/ BAKE will automatically compute
the oven temperature, microwave power and cooking time
for baking, roasting and broiling. Set the desired program
by touching the COMPU BROIL/ ROAST/ BAKE pad, and
number pad. Enter the weight by touching the Number pads.
When the START pad is touched, the following operations
occur:
1. The COOK indicator will light and the Convection Fan
Symbol will rotate.
2. The cooking time will appear on the display and start
counting down to zero. The cooking time is adjusted
automatically according to the weight of the food.
3. The shut-off relays (RY1, RY5 and RY6) are energized,
turning on the oven lamp, turntable motor, cooling fan
motor and convection motor. The power supply voltage
is applied to the heating element.
4. Now, the oven is in the convection cooking mode.
IMPORTANT: 0
23
24
30
32 (sec.)
64 (sec.)
6 sec.
CONVECTION
MOTOR
ON
OFF
3 sec.
THERMISTOR
ON
OFF
Sensing
Voltage
ON
OFF
Sensing the voltage across temperature measurement circuit.
12
E30MO65GSSA
During sensor cooking operation, the fire sensing operation sequence will not begin until the AH sensor has
detected vapors and initiated a sensor cooking cycle.
This is because the operation of the convection fan
would interfere with the AH sensor's vapor detection.
Schematic DIAGRAM
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
RY2
A-9
RY3
CONTROL UNIT
E-1 E-2 E-3
SECONDARY
INTERLOCK
RERAY
E-4 E-5 E-6
F-3
F-2 F-1
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
117V
60Hz
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
THERMISTOR
DAMPER
SWITCH
AH SENSOR
CAPACITOR
0.94µ
MAGNETRON
RY1
RY6
RY4
CONVECTION MOTOR
COM.
(RY3)
POWER
TRANSFORMER
H.V. RECTIFIER
N.O.
(RY1)
A-7
DM
DAMPER MOTOR
TURNTABLE MOTOR
FM
FAN MOTOR
OVEN LAMP
OL
COM.
(RY1)
A5
MONITOR SWITCH
A3
A1
CM
TTM
PRIMARY INTERLOCK SWITCH
OVEN
THERMAL
CUT-OUT
RY5
0.0033µ/AC125V
0.0033µ/AC125V
NOISE SUPPRESSION COIL
0.022µ/AC250V
FUSE
MAGNETRON
THERMAL
CUT-OUT
HEATIMG ELEMENT
CONV.
THERMAL
CUT-OUT
NOISE FILTER
Figure O-1. Oven Schematic-OFF Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. “START” PAD TOUCHED.
RY2
A-9
RY3
CONTROL UNIT
E-1 E-2 E-3
SECONDARY
INTERLOCK
RERAY
E-4 E-5 E-6
F-3
F-2 F-1
117V
60Hz
THIRD DOOR
SWITCH
DOOR
SENSING
SWITCH
THERMISTOR
DAMPER
SWITCH
AH SENSOR
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
Figure O-2. Oven Schematic-Microwave Cooking Condition
13
CAPACITOR
0.94µ
MAGNETRON
A-7
POWER
TRANSFORMER
H.V. RECTIFIER
RY1
RY6
RY4
CONVECTION MOTOR
COM.
(RY3)
DM
DAMPER MOTOR
FM
FAN MOTOR
TURNTABLE MOTOR
OVEN LAMP
N.O.
(RY1)
CM
TTM
OL
COM.
(RY1)
A5
MONITOR SWITCH
A3
A1
PRIMARY INTERLOCK SWITCH
OVEN
THERMAL
CUT-OUT
RY5
0.0033µ/AC125V
0.0033µ/AC125V
NOISE SUPPRESSION COIL
0.022µ/AC250V
FUSE
MAGNETRON
THERMAL
CUT-OUT
HEATIMG ELEMENT
CONV.
THERMAL
CUT-OUT
NOISE FILTER
E30MO65GSSA
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. MIX COOKING PAD TOUCHED.
3. COOKING TIME PROGRAMMED.
4. “START” PAD TOUCHED.
5. RY2 AND RY3 WILL ALTERNATELY CLOSE.
DURING COOK CYCLE.
RY2
A-9
RY3
CONTROL UNIT
E-1 E-2 E-3
SECONDARY
INTERLOCK
RERAY
E-4 E-5 E-6
F-3
F-2 F-1
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
117V
60Hz
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
THERMISTOR
DAMPER
SWITCH
AH SENSOR
CAPACITOR
0.94µ
MAGNETRON
A-7
POWER
TRANSFORMER
H.V. RECTIFIER
RY1
RY6
RY4
CONVECTION MOTOR
COM.
(RY3)
DM
DAMPER MOTOR
TURNTABLE MOTOR
FM
FAN MOTOR
OVEN LAMP
N.O.
(RY1)
CM
TTM
OL
COM.
(RY1)
A5
MONITOR SWITCH
A3
A1
PRIMARY INTERLOCK SWITCH
OVEN
THERMAL
CUT-OUT
RY5
0.0033µ/AC125V
0.0033µ/AC125V
NOISE SUPPRESSION COIL
0.022µ/AC250V
FUSE
MAGNETRON
THERMAL
CUT-OUT
HEATIMG ELEMENT
CONV.
THERMAL
CUT-OUT
NOISE FILTER
Figure O-3. Oven Schematic-Automatic Mix Cooking Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CONVECTION PAD TOUCHED.
3. DESIRED TEMP. TOUCHED.
4. C O O K I N G
T I M E
PROGRAMMED.
5. “START” PAD TOUCHED.
RY2
A-9
RY3
CONTROL UNIT
E-1 E-2 E-3
SECONDARY
INTERLOCK
RERAY
E-4 E-5 E-6
F-3
F-2 F-1
117V
60Hz
THIRD DOOR
SWITCH
DOOR
SENSING
SWITCH
THERMISTOR
DAMPER
SWITCH
AH SENSOR
COM.
(RY2)
N.O.
(RY2)
N.O.
(RY3)
Figure O-4. Oven Schematic-Convection Cooking Condition
14
CAPACITOR
0.94µ
MAGNETRON
RY1
RY6
RY4
COM.
(RY3)
POWER
TRANSFORMER
H.V. RECTIFIER
N.O.
(RY1)
A-7
DM
DAMPER MOTOR
CONVECTION MOTOR
FM
FAN MOTOR
TURNTABLE MOTOR
OVEN LAMP
OL
COM.
(RY1)
A5
MONITOR SWITCH
A3
A1
CM
TTM
PRIMARY INTERLOCK SWITCH
OVEN
THERMAL
CUT-OUT
RY5
0.0033µ/AC125V
0.0033µ/AC125V
NOISE SUPPRESSION COIL
0.022µ/AC250V
FUSE
MAGNETRON
THERMAL
CUT-OUT
HEATIMG ELEMENT
CONV.
THERMAL
CUT-OUT
NOISE FILTER
E30MO65GSSA
DESCRIPTION AND FUNCTION OF COMPONENTS
DOOR SENSING AND PRIMARY INTERLOCK
SWITCHES
THIRD DOOR SWITCH
The switch is activated by the latch heads, while the door
is closed. When the door is opened, the switch interrupt
the circuit to the power transformer. This switch prevents
power transformer engaging and microwave when the door
opened.
The door sensing switch in the secondary interlock system
is mounted in the upper position on the latch hook, the primary interlock switch is mounted in the lower position on
the latch hook. They are activated by the latch heads on the
door. When the door is opened, the switches interrupt the
circuit to all components. A cook cycle cannot take place
until the door is firmly closed thereby activating both interlock
switches. The secondary interlock system consists of the
door sensing switch and secondary interlock relay located
on the control circuit board.
THERMISTOR
The thermistor is a negative temperature coefficient type.
The temperature in the oven cavity is detected through the
resistance of the thermistor, and then the control unit causes
the heater relay to operate, thus the current to the heating
element is turned ON/OFF.
LATCH HOOK
THIRD DOOR SWITCH
MAGNETRON THERMAL CUT-OUT
DOOR SENSING
SWITCH
LATCH
HEADS
The thermal cut-out located on the waveguide is designed to
prevent damage to the magnetron if an over heated condition develops in the magnetron due to cooling fan failure,
obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the thermal cut-out remains closed.
However, when abnormally high temperatures are reached
within the magnetron, the thermal cut-out will open at 257οF
(125οC) causing the oven to shut down. magnetron thermal
cut-out is not reset at room temperature.
MONITOR SWITCH
PRIMARY
INTERLOCK SWITCH
SWITCH LEVER
OPEN LEVER
DOOR OPEN
BUTTON
OVEN THERMAL CUT-OUT
The thermal cut-out located on the side of the steam duct
is designed to prevent damage to the unit if the foods in the
oven catch fire due to over heating produced by improper
setting of cooking time or failure of control unit.
Under normal operation, the thermal cut-out remains closed.
However, when abnormally high temperatures are reached
within the oven cavity, the thermal cut-out will open at 302οF
(150οC) causing the oven to shut down.
When the thermal cut-out has cooled, the thermal cut-out
closes at 266οF (130οC)
Figure D-1. Door sensing switch, monitor switch, third
door switch and primary interlock switch
MONITOR SWITCH
The monitor switch is mounted on the middle position of latch
hook. It is activated (the contacts opened) by the lower latch
head while the door is closed.The switch is intended to render
the oven inoperative by means of blowing the monitor fuse
when the contacts of the relay RY1 and primary interlock
switch fail to open when the door is opened.
CONV. THERMAL CUT-OUT
Functions:
1. When the door is opened, the monitor switch contact close
(to the ON condition) due to their being normally closed. At
this time the door sensing and primary interlock and third
door switches are in the OFF condition (contacts open)
due to their being normally open contact switches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing
switch, third door switch and the primary interlock switch
contacts close. (On opening the door, each of these
switches operate inversely.)
3. If the door is opened, and the relay RY1 and the primary
interlock switch contacts fail to open, the monitor fuse
blows simultaneously with closing of the monitor switch
contacts.
The thermal cut-out located on the left side of the thermal
protection plate (left) is designed to prevent damage to
the heater unit if an over heated condition develops in the
tube due to cooling fan failure, obstructed air ducts, dirty or
blocked air intake, etc.
Under normal operation, the thermal cut-out remains closed.
However, when abnormally high temperatures are reached
within the heater unit, the thermal cut-out will open at 302οF
(150οC) causing the oven to shut down.
When the thermal cut-out has cooled, the thermal cut-out
closes at 266οF (130οC)
HEATING ELEMENT
The heating element is located at the left side of the oven
cavity. It is intended to heat air driven by the convection fan.
The heated air is kept in the oven and force-circulated and
reheated by the heating element.
CAUTION: BEFORE REPLACING A BLOWN MONITOR
FUSE TEST THE DOOR SENSING SWITCH,
PRIMARY INTERLOCK SWITCH, RELAY(RY1)
AND MONITOR SWITCH FOR PROPER
OPERATION. (REFER TO CHAPTER “TEST
PROCEDURE”).
CONVECTION COOKING SYSTEM
This oven is designed with a hot air heating system where
food is not directly heated by the heating element, but is
heated by forced circulation of the hot air produced by the
heating element.
The air heated by the heating element is circulated through
the convection passage provided on the outer casing of the
NOTE: MONITOR FUSE AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
15
E30MO65GSSA
oven cavity by means of the convection fan which is driven
by the convection motor. It then enters the inside of the
oven through the vent holes provided on the left side of the
oven. Next, the hot air heats the food on the turntable and
leaves the oven cavity through the vent in the center of the
oven cavity left side wall.
Without leaving the oven, this hot air is reheated by the
heating element, passes through the convection passage
and enters the inside of the oven cavity again, in a continuing cycle.
In this way, the hot air circulates inside the oven cavity to
raise its temperature and, at the same time, comes into
contact with the food being cooked.
When the temperature inside the oven cavity reaches the
selected temperature, the heating element is de-energized.
When the temperature inside the oven cavity drops below
the selected temperature, the heating element is energized
again. In this way, the inside of the oven cavity is maintained
at approximately the selected temperature.
When the convection time reaches 0, the heating element
is de-energized and the convection fan stops operating and
the oven shuts off.
1-3.When the damper is moved to the open position by
the damper cam the damper switch is closed (ON
position).
1-4.The signal from damper switch is re-sensed in the
control unit and shut-off relay (RY4) is turned off.
1-5.The 120 volts A.C. to the damper motor is removed
and the motor turns off.
2. When oven is microwave cooking:
Damper is in the open position.
3. When oven is convection cooking:
3-1.Damper motor is energized by touching the
convection, temperature and START pads.
3-2.When damper is in the closed position (damper
switch is OFF), its signal is sensed by the control
unit, and shut-off relay (RY4) is de-energized.
3-3.The damper is held in the closed position during the
convection cooking operation.
3-4.At the end of the convection cooking, shut-off relay
(RY4) is energized, and the damper is returned to
the open position.
NOTE: If the damper door is not in the proper position,
closed during convection or open during microwave,
the control unit will stop oven operation after 1
minute.
DAMPER OPEN-CLOSE MECHANISM
Usually, the damper is in the open position except during
convection cooking. Damper position is set automatically
by damper motor, damper switch, motor cam and damper
shaft. These components are operated by a signal that
judges if microwave cooking or convection cooking operation is selected by the control unit.
Figure D-2. Damper Mechanism
Microwave Cooking:
Damper is in the open position, because a portion of cooling
air is channelled through the cavity to remove steam and
vapors given off from the heating foods.
It is then exhausted at the top of the oven cavity into a
condensation compartment.
Convection Cooking:
Damper is in the closed position, so that no hot air will be
allowed to leak out the oven cavity.
DAMPER SHAFT
DAMPER DUCT
DAMPER
Damper Operation
1. When power supply cord is plugged in:
1-1.When power supply cord is plugged in, a signal is
sensed in the control unit, and operates shut-off
relay (RY4).
1-2.Contacts of shut-off relay (RY4) close, the damper
motor is energized, opening the damper door.
DAMPER CAM
DAMPER SWITCH
DAMPER MOTOR
TROUBLESHOOTING GUIDE
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter
which will be found in the “Test Procedure”section.
IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1),
door sensing switch and primary interlock switch before replacing the monitor fuse. If monitor fuse is replaced,
the mintor switch must also be replaced at the same time. Use part FFS-BA012WRK0 as an assembly.
16
TEST PROCEDURE
O
PROBLEM
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
A
MAGNETRON
B
POWER TRANSFORMER
C
H.V. RECTIFIER ASSEMBLY
D
HIGH VOLTAGE CAPACITOR
E
PRIMARY INTERLOCK SWITCH
F
SECONDARY INTERLOCK SYSTEM
G
MONITOR SWITCH
H
MONITOR FUSE
E
THIRD DOOR SWITCH
I
THERMAL CUT-OUT
J
CONVECTION HEATER
K
THERMISTOR
L
DAMPER MOTOR
M
DAMPER SWITCH
P
TOUCH CONTROL PANEL
Q
KEY UNIT
R
RELAY RY-1
R
RELAY RY-2
R
RELAY RY-3
R
RELAY RY-4
R
RELAY RY-5
R
RELAY RY-6
T
FOIL PATERN ON PWB.
U
AH SENSOR
Replace OVEN LAMP OR SOCKET
Replace FAN MOTOR
Replace TURNTABLE MOTOR
Replace
Check LOOSE WIRING
CONVECTION MOTOR
Check SHORTED IN POWER CORD
Check NO POWER AT OUTLET
Check LOW VOLTAGE
NOISE FILTER
17
Oven in the sensor cooking condition but AH sensor does not end or
(CONVECTION)
Convection cycle runs 4 minutes and 15 seconds then shuts down.
Cooling fan motor runs intermittently or all the time.
Temperature in the oven cavity is lower or higher than preset.
CONV indicator lights, but heating element does not heat.
(MICROWAVE)
CONV indicator lights, but oven does not go into cook cycle when
START pad is touched.
Function of COMPU DEFROST does not operate properly.
Function of variable cooking does not operate properly except HIGH
power.
Extremely uneven heating is produced in oven load (food).
COOKING CONDITION
Low or no power is produced during microwave cooking (The food is
heated incompletely or not heated at all)
Oven does not go into a cook cycle, when START pad is touched.
Turntable motor operates normally but cooling fan motor does not
operate.
Oven lamp light, but turntable motor does not operate.
Cooking cycle runs 1 minute then shuts down.
OFF CONDITION
Oven lamp does not light in cook cycle. (It light when door is
opened).
Oven lamp does not light with door opened.
Display does not operate properly when STOP/CLEAR pad is touched.
(The time of day should appear on the display with beep sound.)
88:88 does not appear in display when power cord is first plugged
into wall receptacle.
CONDITION
Monitor fuse blows when power cord is plugged into wall receptacle
Home fuse blows when power cord is plugged into wall receptacle.
E30MO65GSSA
(SENSOR
COOKING)
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
A
MAGNETRON ASSEMBLY TEST
COMPONENT TEST
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD BE OBSERVED.
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS OR WIRING.
To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check
across the magnetron filament leads should indicate less than 1 ohm.
To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads
and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance the
magnetron is grounded and must be replaced.
Power output of the magnetron can be measured by performing a water temperature rise test. This
test should only be used if above tests do not indicate a faulty magnetron and there is no defect in the
following components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test
will require a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple
type temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water
with a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple
through the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER HI(HIGH) selecting more than 60
seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second
hand of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be
22 to 43οF(12.2 to 23.8οC) rise in temperature. If the water temperatures are accurately measured
and tested for the required time period the test results will indicate if the magnetron tube has low
power output (low rise in water temperature) which would extend cooking time or high power output
(high rise in water temperature) which would reduce cooking time. Because cooking time can be
adjusted to compensate for power output, the magnetron tube assembly should be replaced only if
the water temperature rise test indicates a power output well beyond the normal limits. The test is
only accurate if the power supply line voltage is 117 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter.
Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of the primary
coil should be less than 1 ohm and the resistance of the high voltage coil should be approximately 84.4
ohms; the resistance of the filament coil should be less than 1 ohm.
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance across
the terminals and observe, reverse the leads to the rectifier terminals and observe meter reading. If a
short is indicated in both directions, or if an infinite resistance is read in both directions, the rectifier is
probably defective and should be replaced.
D
HIGH VOLTAGE CAPACITOR TEST
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
18
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and
check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate continuity for a short time and should indicate approximately 10 MΩ once the capacitor is charged. If the
above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either of
the terminals and case. If it is shorted, replace the capacitor.
E
PRIMARY INTERLOCK SWITCH AND THIRD DOOR SWITCH TEST
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicated an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the switch.
F
SECONDARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicated an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
SECONDARY INTERLOCK RELAY
Disconnect two (2) wire leads from the tab terminal of the secondary interlock relay (RY2). Check the
state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts
are closed, replace the circuit board entirely or the relay itself.
G
MONITOR SWITCH
Disconnect the oven from power supply.
Before performing this test, make sure that the primary interlock switch and the secondary interlock
relay are operating properly, according to the above Test Procedures. Disconnect the wire lead from the
monitor switch (NC) terminal. Check the monitor switch operation by using the ohmmeter as follows.
When the door is open, the meter should indicate a closed circuit. When the monitor switch actuator
is pushed by a screw driver through the lower latch hole on the front plate of the oven cavity with the
door opened (in this condition the plunger of the monitor switch is pushed in), the meter should indicate an open circuit. If improper operation is indicated, the switch may be defective. After testing the
monitor switch, re-connect the wire lead to the monitor switch (NC) terminal and check for continuity
of monitor circuit.
N.C.
MONITOR SWITCH
COM.
SCREW DRIVER
PRIMARY
INTERLOCK
SWITCH
H
OHMMETER
BLOWN MONITOR FUSE
If the monitor fuse is blown when the door is opened, check the primary interlock switch, door sensing
switch relay (RY1) and monitor switch according to the "TEST PROCEDURE" for those switches before
replacing the blown monitor fuse.
CAUTION: If the monitor fuse is blown by improper switch operation, the monitor fuse and switch must be replaced with "monitor fuse and switch
assembly" part number FFS-BA012WRK0, even if the monitor switch operates normally. The monitor fuse and switch assembly is packed with
20 ampere fuse and switch.
I
OVEN THERMAL CUT-OUT (on the side of steam duct)
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the temperature of the oven thermal cut-out reaches approximately 302οF (150οC). The thermal cut-out reset
automatically at approximately 266οF (130οC). If the thermal cut-out has operated under the normal condition, replace the thermal cut-out. An open thermal cut-out indicates overheating of the oven cavity.
19
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
MAGNETRON THERMAL CUT-OUT (on the waveguide)
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of the thermal cut-out reaches approximately 257οF (125οC).
An open thermal cut-out indicates overheating of the magnetron. Check for restricted air flow to the
magnetron through the vent holes of the oven cavity, especially the cooling duct and cooling fan.
CAUTION: IF THE THERMAL CUT-OUT INDICATES OPEN CIRCUIT AT ROOM TEMPERATURE,
REPLACE THE THERMAL CUT-OUT.
CONVECTION CUT-OUT (on side of the heater duct)
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of thermal cut-out reaches 302οF (150οC). The thermal cut-out resets automatically at
approximately 266οF (130οC). If the thermal cut-out has operated under the normal condition, replace the thermal cut-out. An open thermal cut-out indicates overheating of heater unit, check for
restricted air flow to the heater unit through the vent hole of the oven cavity, especially the heater
duct and convection fan.
J
HEATING ELEMENT TEST
Make sure the heating element is fully cooled and test as follows;
a. Disconnect wire leads and measure the resistance with an ohmmeter. On the R x 1 scale, the
resistance between the heating element terminals should be approximately 10.2Ω.
b. Disconnect wire leads and measure the insulation resistance with 500V - 100MΩ insulation resistance
meter. The insulation resistance between heating element terminal and cavity should be more than
0.5MΩ.
K
THERMISTOR TEST
Disconnect connector-E from the control unit. Measure the resistance of the thermistor with an ohmmeter. Connect the ohmmeter leads to Pin No’s E-3 and E-4.
Room Temperature
68οF(20οC) - 86οF(30οC)
Resistance
Approx. 350kΩ - 155KΩ
If the meter does not indicate above resistance, replace the thermistor
L
DAMPER MOTOR TEST
When the power cord is plugged into the wall receptacle and 117 volts A.C. is supplied to the damper
motor, the motor operates until the damper is opened and the damper switch closes. Then the damper
motor stops operation.
If the damper motor does not operate, check for A.C. voltage with a voltmeter at the motor.
1. Disconnect the power cord from the wall receptacle.
2. Disconnect the wire leads of motor and connect the meter leads to the wire leads of main wire
harness.
3. Re-connect the power cord into the wall receptacle.
If 117 volts A.C. is indicated at the wire leads, replace the motor and if 117 volts A.C. is not indicated,
check the wire harness and control unit.
M
DAMPER SWITCH TEST
Disconnect the wire leads from the switch terminals and connect ohmmeter leads to the common
(COM.) and normally open (N.O.) terminals of the switch.
1. When switch actuator is pushed by the damper motor cam, the meter should be indicated a closed
circuit.
2. When power cord is plugged into the wall receptacle, the damper motor operates and damper cam
will start to rotate. When the switch actuator is released, the meter should be indicated an open
circuit. If improper operation is indicated, replace the damper switch.
N
CHECKING TEMPERATURE IN THE CONVECTION MODE
It is difficult to measure the exact temperature in the convection oven. An accurate thermocouple type
20
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
temperature tester must be used. A low priced bi-metal type thermometer is not reliable or accurate.
The temperature should be checked with outer case cabinet installed, approx. 5 minutes after preheat
temperature is reached (audible signal sounds four times). The temperature experienced may be approx. 30οF more or less than indicated on the display, however, in most cases the food cooking results
will be satisfactory.
Difference in power supply voltage will also affect the oven temperature. The Household power supply
voltage may sometimes become lower than the rated voltage (117 V) and cause under-cooking. If the
power supply voltage is 10% lower than the rated voltage, longer cooking time is required by 10% to
20%.
O
NOISE FILTER TEST
NOISE FILTER
N
H
FUSE 20A
Disconnect the oven from power supply.
Disconnect the lead wires from the terminal the noise filter. Using
an ohmmeter, check between the terminals as described in the
following table.
MEASURING POINT
P
LINE CROSS CAPACITOR
0.22µF / AC 250V
INDICATION OF OHMMETER
Between N and H
Open circuit.
Between terminal N and GRAY
Short circuit.
Between terminal H and RED
Short circuit.
If incorrect reading are obtained, replace the noise filter.
NOISE SUPPRESSION COIL
LINE BYPASS
CAPACITOR
0.0033µF / AC 125V
GRY
LINE BYPASS
CAPACITOR
0.0033µF / AC 125V
RED
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit and troubleshooting by unit replacement is described according to the symptoms indicated.
1. Key Unit. Note : Check key unit ribbon connection before replacement.
The following symptoms indicate a defective key unit. Replace the key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
2. Control Unit
The following symptoms indicate a defective control unit. Replace the control unit.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) All digits in the figure flicker.
2-3 Other possible troubles caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
d) Proper temperature measurement is not obtained.
Note: When defective components, the Control Unit or Key Unit are replaced, the defective part or
parts must be properly packed for return in the shipping carton, with its cushion material, in
which the new replacement part was shipped to you.
21
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
Q
COMPONENT TEST
KEY UNIT TEST
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact.
If the control unit responds by clearing with a beep the key unit is faulty and must be replaced. If the
control unit does not respond, it is a faulty and must be replaced. If a specific pad does not respond,
the above method may be used (after clearing the control unit) to determine if the control unit or key
pad is at fault.
G5
G6
G7
G8
G9
G10
G11
G12
G4
G3
G2
ADD A DEFROST SENSOR
COOK
MINUTE
POPCORN PREHEAT
REHEAT
SLOW
COOK
AUTO
ROAST
AUTO
BAKE
HIGH MIX
ROAST
BROIL
CONVEC
BAKE
1
2
3
4
5
100˚F
150˚F
275˚F
300˚F
325˚F
LOW MIX
BAKE
6
7
8
9
0
350˚F
375˚F
400˚F
425˚F
450˚F
TIMER
POWER
LEVEL
CLOCK
START
TOUCH ON
STOP
CLEAR
HELP
G1
AUTO
BROIL
KEY UNIT
R
RELAY TEST
Remove the outer case and check voltage between Pin Nos. 7 and 9 of the 9- pin connector (A) on the
control unit an A.C. voltmeter. The meter should indicate 20 volts, if not check the oven circuitry.
Shut-off, Cook and Heater Relay Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation or convection cooking operation.
DC. voltage indicated ............. Defective relay.
DC. voltage not indicated ........ Check diode which is connected to the relay coil. If diode is good, control
unit is defective.
RELAY SYMBOL
S
OPERATIONAL VOLTAGE
CONNECTED COMPONENTS
RY
Approx. 9.0V D.C.
Oven lamp / Turntable motor
RY2(COOK)
Approx. 8.0V D.C.
Power transformer
RY3(HEATER)
Approx. 8.0V D.C.
Heating element
RY4
Approx. 9.0V D.C.
Damper motor
RY5
Approx. 9.0V D.C.
Convection motor
RY6
Approx. 9.0V D.C.
Cooling fan motor
COMPU DEFROST TEST
() Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the "COMPU DEFROST" pad twice and touch the Number pad "5". And then
touch the "START" pad.
(3) After 2 sec. Now the oven is in COMPU DEFROST cooking condition.
(4) The oven will operate as follows.
WEIGHT
0.5lbs
ST STAGE
LEVEL TIME
70%
47sec.
2ND STAGE
3RD STAGE
LEVEL TIME LEVEL
TIME
0%
52sec.
50%
32sec.
4TH STAGE
LEVEL
TIME
30%
40sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
22
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
T
COMPONENT TEST
PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING BOARD
(PWB) IS OPEN.
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary
on the PWB, this foil pattern acts as a fuse. If the foil pattern is open, follow the troubleshooting guide
given below for repair.
Problem: POWER ON, indicator does not light up.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
The rated voltage is not applied to POWER terminal of CPU connector (CN-A).
2
Check supply voltage and oven power cord.
The rated voltage is applied to primary side Power transformer or secondary circuit defective.
of power transformer.
Check and repair.
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
3
4
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
3
T1
26
9
CN - A
POWER
a
(J1)
7
U
b
5
P
d
VRS1
3
CONV M FAN M
NOTE: *At the time of making these repairs, make
a visual inspection of the varistor. Check for
burned damage and examine the transformer
with an ohmmeter for the presence of layer
short-circuit (check the primary coil resistance which is approximately 175Ω ± 10%). If
any abnormal condition is detected, replace
the defective parts.
c
AH SENSOR TEST
Checking the initial sensor cooking condition
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95οF (35οC).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the "INSTALLATION
Instructions".
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapour given of by the spray and turn off before food is properly cooked.
(8) After 30 minutes if the sensor has not detected the vapour of the food, ERROR will appear and the
oven will shut off.
Water load cooking test
Make sure the oven has been plugged in at least five minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch SENSOR COOK pad and number pad 1. Now, the oven is in the sensor cooking condition
and "BAKED POTATO" will appear in the display.
(5) Touch Start pad. The oven will operate for the first 16 seconds, without generating microwave energy.
23
E30MO65GSSA
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
When the AH sensor is defective (open or short), Error will appear in the display after 16 seconds
cleaning time.
If ERROR appears check sensor wire connections and/or AH sensor.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(6) After approximately 16 seconds, microwave energy is produced, and the display should start to count
down the remaining cooking time and oven should turn off after water is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement
sensor.
(1) Disconnect oven from power supply and remove outer case.
(2) Discharge the high voltage capacitor.
(3) Remove the AH sensor.
(4) Install the new AH sensor.
(5) Re-install the outer case.
(6) Reconnect the oven to the power supply and check the sensor cook operation proceed as follows:
6-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
6-2. Place the container on the center of tray in the oven cavity.
6-3. Close the door.
6-4. Touch SENSOR COOK pad and number 1 pad.
6-5. Touch Start pad. The control panel is in automatic Sensor operation.
6-6. The display will start to count down the remaining cooking time, and the oven will turn off automatically after the water is boiling (bubbling).
If new sensor dose not operate properly, the problem is with the control unit.
CHECKING CONTROL UNIT
(1) Disconnect oven from power supply and remove outer case.
(2) Discharge the high voltage capacitor.
(3) Disconnect the wire leads from the cook relay.
(4) Disconnect the sensor connector that is mounted to lower portion of control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Reconnect the oven to the power supply and check the sensor cook operation proceed as follows:
6-1. Touch SENSOR COOK pad and number 1 pad.
6-2. Touch Start pad. The control panel is in the sensor cooking operation.
6-3. After approximately 20 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
6-4. After approximately 3 seconds, the display shows " X X . X X " which is the remaining cooking
time, and the display count down.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
Plunger
F-1
F-2
F-3
To connector (F)
on Control Unit.
1
NC
NO
R1,R2 : 22Ω ± 1% 1/2W
R3 : 4.3kΩ ± 5% 1/4W
R4 : 1MΩ ± 5% 1/4W
2
3
COM NO
R1
R2
CONNECTOR
COM
R3
R4
Sensor Dummy Resistor Circuit
24
NC
E30MO65GSSA
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
The touch control section consists of the following units
as shown in the touch control panel circuit.
5) Buzzer Circuit
The buzzer is responds to signals from the LSI to emit
noticing sounds (key touch sound and completion
sound).
(1) Key Unit
(2) Control Unit
6) Temperature Measurement Circuit : (OVEN
THERMISTOR)
The temperature in the oven cavity is sensed by the
thermistor.The variation of resistance according to sensed
temperature is detected by the temperature measurement
circuit and the result applied to LSI. The LSI uses this
information to control the relay and display units.
The principal functions of these units and the signals communicated among them are explained below.
Key Unit
The key unit is composed of a matrix, signals P10 - P17
generated in the LSI are sent to the key unit.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through R24 - R27
to perform the function that was requested.
7) Absolute Humidity Sensor Circuit
This circuit detects the humidity of a food which is being
cooked, to control its automatic cooking.
Control Unit
Control unit consists of LSI, power source circuit, synchronizing signal circuit, ACL circuit, buzzer circuit, temperature
measurement circuit, absolute humidity sensor circuit and
indicator circuit.
8) Door Sensing Switch
A switch to inform the LSI if the door is open or closed.
9) Relay Circuit
To drive the magnetron, heating element, fan motor,
convection motor, damper motor, turntable motor and
light the oven lamp.
1) LSI
This LSI controls the temperature measurement signal,
AH sensor signal, key strobe signal, relay driving signal
for oven function and indicator signal.
10) Indicator Circuit
Indicator element is a Fluorescent Display.
Basically, a Fluorescent Display is triode having a
cathode, a grid and an anode. Usually, the cathode of a
Fluorescent Display is directly heated and the filament
serves as cathode.
The Fluorescent Display has 8-digits, 16-segments are
used for displaying figures.
2) Power Source Circuit
This circuit generates the voltages necessary for the
control unit from the AC line voltage.
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit. It incorporates a very small error because it works
on commercial frequency.
4) ACL Circuit
A circuit to generate a signals which resetting the LSI to
the initial state when power is applied.
DESCRIPTION OF LSI
LSI(IXA103DR):
The I/O signals of the LSI(IXA103DR) are detailed in the following table.
Pin No. Signal
I/O
1
VCC
IN
2
VEE
IN
3
AVSS
IN
Description
Connected to GND.
Anode (segment) of Fluorescent Display light-up voltage: -30V.
Vp voltage of power source circuit input.
Power source voltage: -5V.
VC voltage of power source circuit input.
4
VREF
IN
Reference voltage input terminal.
A reference voltage applied to the A/D converter in the LSI. Connected to
GND.(0V)
25
E30MO65GSSA
Pin No.
5
Signal
I/O
Description
AN7
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input
is an analog input terminal from the AH sensor circuit, and connected to the A/D
converter built into the LSI.
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to
the A/D converter built into the LSI.
Heating constant compensation terminal.
Input signal which communicates the door open/close information to LSI.
Door closed; "H" level signal(0V).
Door opened; "L" level signal(-5V).
Input signal which communicates the damper open/close information to LSI.
Damper opened; "H" level signal(0V:GND).
Damper closed; "L" level signal(-5V).
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the thermistor,
this input is converted into temperature by the A/D converter built into the LSI.
Digit selection signal.
The relationship between digit signal and digit are as follows;
H
Digit signal
Digit
ß(60Hz)
6
AN6
IN
7-9
AN5-AN3
IN
10
AN2
IN
11
AN1
IN
12
AN0
IN
13
P55
OUT
L
P03............................. 1st.
P02............................2nd.
P01.............................3rd.
P00.............................4th.
P37.............................5th.
P36............................ 6th.
P35............................ 7th.
14
P54
OUT
GND
P03
VP
P02
P0
P00
P37
P36
P55............................ 8th.
P35
Normally, one pulse is output in every ß
P55
period, and input to the grid of the Fluorescent Display.
Oven lamp and turntable motor driving signal. (Square Waveform : 60Hz)
To turn on and off the shut-off relay(RY1). The
square waveform voltage is delivered to the
relay(RY1) driving circuit.
6.7 msec.
H
L
During cooking
15
P53
OUT
16
P52
OUT
17
P51
OUT
Convection motor driving signal.
To turn on and off shut-off relay(RY5). "L" level
ON
during CONVECTION; "H" level otherwise.
Cooling fan motor driving signal.
To turn on and off shut-off relay(RY6). "L"
level during both microwave and convection
ON
cooking; "H" level otherwise.
Magnetron high-voltage circuit driving VARI MODE
signal.
P-HI (100% power)
To turn on and off the cook relay(RY2). In
P-HI operation, the signals holds "L" level
during microwave cooking and "H" level
while not cooking. In other cooking modes
(P-90, P-80, P-70, P-60, P-50, P-40, P-30,
P-20, P-10, P-0) the signal turns to "H"
level and "L" level in repetition according
to the power level.
26
During
cooking
(Convection)
During
cooking
OFF
H. GND
L
OFF
H. GND
L
ON TIME
OFF TIME
32 sec.
0 sec.
P-90 (approx. 90% power)
30 sec.
2 sec.
P-80 (approx. 80% power)
26 sec.
6 sec.
P-70 (approx. 70% power)
24 sec.
8 sec.
P-60 (approx. 60% power)
22 sec.10 sec.
P-50 (approx. 50% power)18 sec.14 sec.
P-40 (approx. 40% power)16 sec.16 sec.
P-30 (approx. 30% power)12 sec.
20 sec.
P-20 (approx. 20% power)
8 sec.
24 sec.
P-10 (approx. 10% power)
6 sec.
26 sec.
P-0 (0% power)
0 sec.
32 sec.
E30MO65GSSA
Pin No.
18
Signal
I/O
P50
OUT
Description
Damper motor relay driving signal.
H : GND
OFF
To turn on and off shut-off relay(RY4).
19
P47
OUT
Heating element driving signal.
To turn on and off shut-off relay(RY3). "L" level durH. GND
During
ing convection cooking; "H" level otherwise. During
OFF
cooking
(Convection)
convection cooking, the signal becomes "H" level
ON
L
when the temperature of the oven cavity exceeds
the predetermined temperature.
Terminal not used.
Timing signal output terminal for temperature measurement(OVEN THERMISTOR).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing.(Convection cooking)
Signal to sound buzzer.
A: key touch sound.
B: Completion sound.
C: When the temperature of the oven cavity
reaches the preset temperature in the
preheating mode, or when the preheating hold time (30 minutes) is elapsed.
Timing signal output terminal for temperature measurement(OVEN).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing.(Convection cooking)
Signal to synchronize LSI with commercial power source frequency.
20-21
22
P46-P45
P44
OUT
OUT
23
P43
OUT
ON
L
H
ß(60Hz)
L
GND
P03
VP
P02
P0
P00
P37
P36
P35
P55
24
P42
OUT
25
INT1
IN
H : GND
This is the basic timing for all real time
processing of LSI.
L (-5V)
6.7 msec.
26
P40
IN
27
RST
IN
28/29 XCIN/XCOUT OUT
30
XIN
IN
31
XOUT
OUT
32
VSS
IN
33
P27
IN
34
P26
IN
35
P25
IN
36
P24
IN
Connected to GND.
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to "L" level the moment power is applied, at this time the LSI is reset. Thereafter
set at "H" level.
Terminal not used.
Internal clock oscillation frequency setting input.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit
with respect to XOUT terminal.
Internal clock oscillation frequency control output.
Output to control oscillation input of XIN.
Power source voltage: -5V.
VC voltage of power source circuit input.
Signal coming from touch key.
When any one of G-1 line keys on key matrix is touched, a corresponding signal
from P10 - P17 will be input into P27. When no key is touched, the signal is held at
"L" level.
Signal similar to P27.
When any one of G-2 line key on key matrix is touched, a corresponding signal will
be input into P26.
Signal similar to P27.
When any one of G-3 line key on key matrix is touched, a corresponding signal will
be input into P25.
Signal similar to P27.
When any one of G-4 line key on key matrix is touched, a corresponding signal will
be input into P24.
27
E30MO65GSSA
Pin No.
Signal
I/O
37
P23
OUT
Description
Segment data signals.
The relation between signals and indicators are as follows:
SignalSegment SignalSegment SignalSegment SignalSegment
P23...............P1
P17.............. P5
P13............... P9
P07.............P13
P22...............P2
P16.............. P6
P12............. P10
P06.............P14
P21...............P3
P15.............. P7
P11............. P11
P05.............P15
49-53
P07-P03
OUT
54-56
P02-P00
OUT
57-59
P37-P35
OUT
P20...............P4 P14.............. P8 P10............. P12 P04.............P16
Segment data signal.
Signal similar to P23.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-12 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-11 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-10 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-9 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-8 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-7 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-6 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-5 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Digit selection signal.
Signal similar to P55.
Digit selection signal.
Signal similar to P55.
60-64
Used for initial balancing of the bridge circuit (absolute humidity sensor).
38-40
P22-P20
OUT
41
P17
OUT
42
P16
OUT
43
P15
OUT
44
P14
OUT
45
P13
OUT
46
P12
OUT
47
P11
OUT
48
P10
OUT
P34-P30
OUT
28
E30MO65GSSA
ABSOLUTE HUMIDITY SENSOR CIRCUIT
(1)Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
Sensing part
(Open vessel)
Ventilation
openings
Sensing part
(Closed vessel)
Sensing part Sensing part
(Open vessel) (Closed vessel)
Thermistor
element
Sensor
case
Thermistor
element
View of sensor case removed
Cross section view
(2)Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an
absolute humidity sensor. A bridge circuit is formed by
two thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it heated
at about 150οC (302οF), the resultant heat is dissipated
in the air and if the two thermistors are placed in different
humidity conditions they show different degrees of heat
conductivity leading to a potential difference between
them causing an output voltage from the bridge circuit, the
intensity of which is increased as the absolute humidity
of the air increases. Since the output is very minute, it
is amplified by the operational amplifier.
the LSI observes the initial voltage available at its AN6
terminal.
With this voltage given, the switches SW1 to SW5 in
the LSI are turned on in such a way as to change the
resistance values in parallel with R50-1. Changing the
resistance values results in that there is the same potential
at both F-3 terminal of the absolute humidity sensor and
AN7 terminal of the LSI. The voltage of AN6 terminal
will indicate about -2.5V. This initial balancing is set
up about 16 seconds after the unit is put in the Sensor
Cooking mode. As the sensor cooking proceeds, the food
is heated to generate moisture by which the resistance
balance of the bridge circuit is deviated to increase the
voltage available at AN6 terminal of the LSI.
Then the LSI observes that voltage at AN6 terminal and
compares it with its initial value, and when the comparison
rate reaches the preset value (fixed for each menu to
be cooked), the LSI causes the unit to stop sensor
cooking; thereafter, the unit goes in the next operation
automatically.
When the LSI starts to detect the initial voltage at AN6
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance, of
the bridge circuit due to disconnection of the absolute
humidity sensor, ERROR will appear on the display and
the cooking is stopped.
1) Absolute humidity sensor circuit
IC2(IZA495DR)
C. Thermistor in
closed vesssl
S. Thermistor in
open vessel
47k
11
F-1
C
F-3
3.57k
S
3.32k 1.8k
VA : -15V
29
62
7
61
75k
8
60
3
5
+
10k
-
9
12
VA : -15V
P31
P32
P33
P34
1
VC : -5V
SW2
SW3
SW4
SW5
AN7
LSI
(IC1)
2
47k
360k
10
R51
F-2
6
150k
37.4k
Absolute humidity (g/m 2 )
(3)Detector Circuit of Absolute Humidity Sensor
Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to
control sensor cooking of the unit. When the unit is set
in the sensor cooking mode, 16 seconds clearing cycle
occurs than the detector circuit starts to function and
63
SW1
P30
0.01µF
S : Thermistor
open vessel
C : Thermistor
closed vessel
64
5
0.01µF
-
4
300k
0.015µF
R3
R2
0.1
µF
S
R1
620k
Output voltage
C
Operational
amplifier
Output
voltage
+
Absolute humidity vs,
output voltage characterist
6
AN6
E30MO65GSSA
SERVICING
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the circuits.
When handling these parts, the following precautions
should be strictly followed. CMOS LSI have extremely
high impedance at its input and output terminals. For this
reason, it is easily influenced by the surrounding high
voltage power source, static electricity charge in clothes,
etc, and sometimes it is not fully protected by the built-in
protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
while keeping it connected to the oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, therefore, it is possible to check and repair
the controls of the touch control panel while keeping it
apart from the oven proper; in this case you must short
both ends of the door sensing switch (on PWB) of the
touch control panel with a jumper, which brings about
an operational state that is equivalent to the oven door
being closed. As for the sensor-related controls of the
touch control panel, checking them is possible if dummy
resistor(s) with resistance equal to that of the controls
are used.
(2)Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper,and short both ends of the door sensing
switch (on PWB) of the touch control panel,which brings
about an operational state that is equivalent to the oven
door being closed. Connect an external power source
to the power input terminal of the touch control panel,
then it is possible to check and repair the controls of
the touch control panel it is also possible to check the
sensor-related controls of the touch control panel by
using the dummy resistor(s).
approx. 1M ohm
2. Shapes of Electronic Components
E
C
Transistor
B
Transistor
2SB910M
E
CB
DTA123ES
KRA101M
KRA223M
KRC243M
4. Servicing Tools
Tools required to service the touch control panel
assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a grounding
terminal.)
2) Oscilloscope: Single beam, frequency range: DC - 10MHz
type or more advanced model.
3) Others: Hand tools
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform the
servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.
(1)Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING SERVICING
PRESENTS A HAZARD.
Therefore, when checking the performance of the touch
control panel, put the outer cabinet on the oven to
avoid touching the high voltage transformer, or unplug
the primary terminal (connector) of the high voltage
transformer to turn it off; the end of such connector must
be insulated with an insulating tape. After servicing, be
sure to replace the leads to their original locations.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that
the two can't be separated.
For those models, check and repair all the controls
(sensor-related ones included) of the touch control panel
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminum foil applied for preventing static
electricity.
2) Connect the connector of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminum foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision
is required.
30
E30MO65GSSA
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
CAUTION: DISCONNECT OVEN FROM POWER SUPPLY BEFORE REMOVING OUTER CASE.
DISCHARGE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS OR WIRING
AFTER REMOVING OUTER CASE.
OUTER CASE REMOVAL
WARNING
FOR WIRING
To prevent an electric shock, take the following manners.
1. Before wiring,
1) Disconnect the power supply.
2) Open the door and wedge the door open.
3) Discharge the high voltage capacitor and wait for
60 seconds.
2. Don’t let the wire leads touch to the followiong parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Convection heater, Oven lamp, Magnetron, High
voltage transformer and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Weveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case
cabinet.
4. Insert the positive lock connector certainly until its pin
is locked. And make sure that the wire leads should
not come off even if the wire leads is pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
OUTER CASE REMOVAL
To remove the components, procedure as follows.
1. Disconnect oven from power supply.
2. Remove screws from rear and along the side edge of
case.
3. Slide the entire case back out about 1 inch (3 cm) to free
it from retaining clips on the cavity face plate.
4. Lift entire case from the unit.
CAUTION: Disconnect oven from power supply
before removing outer case.
POWER TRANSFORMER REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect filament leads of transformer from the
magnetron and capacitor.
4. Disconnect high voltage lead of capacitor from the
transformer.
5. Disconnect wire leads from the transformer.
6. Remove two (2) screws holding the transformer to the
base cabinet.
3. Make sure the transformer is mounted correctly to the
corners underneath those tabs.
4. After re-installing the transformer, secure the transformer
with two screws to the base cabinet, one is with outer tooth
washer and the other is without outer-tooth washer.
5. Re-connect the wire leads (primary and high voltage)
and high voltage lead to the transformer and filament
leads of transformer to the magnetron and capacitor,
referring to the “Pictorial Diagram”.
6. Re-install the outer case and check that the oven is
operating properly.
Re-install
1. Rest the transformer on the base cabinet with its primary
terminals toward rear cabinet.
2. Insert the two edges of the transformer into two metal
tabs of the base cabinet.
NOTE HOT (ORANGE) WIRE MUST BE CONNECTED
TO THE POWER TRANSFORMER TERMINAL
NEAREST TO THE TRANSFORMER MOUNTING
SCREW.
MAGNETRON REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor. Disconnect filament
lead of transformer from magnetron. Disconnect high
voltage wire lead from magnetron.
3. Carefully remove four (4) mounting screws hold the
magnetron to waveguide, when removing the screws
holding the magnetron to prevent it from falling.
4. Remove the magnetron from the unit with care so the
magnetron tube should not hit by any metal object around
the tube.
CAUTION: WHEN REPLACING THE MAGNETRON, BE
SURE THE R.F. GASKET IS IN PLACE AND
THE MAGNETRON MOUNTING SCREWS
ARE TIGHTENED SECURELY.
31
E30MO65GSSA
HIGH VOLTAGE RECTIFIER ASSEMBLY REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Remove one (1) screw holding the rectifier assembly to
the capacitor holder.
4. Disconnect the rectifier assembly from the capacitor and
magnetron.
CAUTION: WHEN REPLACING THE SILICON RECTIFIER ASSEMBLY, THE GROUND SIDE TERMINAL MUST BE SECURED FIRMLY WITH A
GROUNDING SCREW.
HIGH VOLTAGE CAPACITOR REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Disconnect the high voltage wire leads and rectifier
assembly from high voltage capacitor and magnetron.
4. Disconnect filament lead of transformer from high voltage
capacitor.
5. Disconnect high voltage wire lead of capacitor from
transformer.
6. Remove one (1) screw and washer holding the rectifier
from the capacitor holder.
7. Remove one (1) screw holding the capacitor holder to
the rear cabinet.
8. Remove the capacitor from the holder.
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
Positive lock®
connector
1
Push the lever of positive lock® connector. Pull down on the
positive lock® connector.
Push
Lever
CAUTION: When you connecting the positive
lock® connectors to the terminals,
install the positive lock® so that the
lever faces you.
2
Pull down
Figure C-1. Positive lock®connector
CONVECTION MOTOR REMOVAL
1. Disconnect oven from power supply and remove outer case.
2. Discharge the high voltage capacitor.
3. Disconnect wire leads from the convection motor. Remove
the convection fan belt.
4. Remove two (2) screws holding the convection motor
mounting angle to the heater duct and base cabinet.
5. Take out the convection motor assembly from the unit.
The convection motor assembly is now free.
6. Remove two (2) screws and nuts holding the motor to
mounting angle.
7. Remove pulley (M) from the motor shaft. Convection
motor is now free.
TURNTABLE MOTOR REMOVAL
1. Disconnect the oven from power supply.
Remove the turntable tray, and the turntable support out
of the oven cavity.
2. Turn the oven upside down and remove one (1) screw
holding the turntable motor cover to the base plate and
take off the turntable motor cover.
3. Disconnect wire lead from the turntable motor.
4. Remove the two (2) screws holding the turntable motor
and coupling mounting plate to the oven cavity bottom.
5. Turntable motor, Coupling mounting plate and Thermal
protection plate bottom will be free.
DAMPER ASSEMBLY REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Disconnect wire leads from damper motor and damper
switch.
4. Remove two (2) oven side screws holding damper motor
angle to thermal protection plate (right).
5. Damper assembly is free.
6. Remove one (1) screw holding damper motor to damper
motor angle and one (1) screw holding damper switch
to damper motor angle.
7. Damper motor and switch are free.
32
E30MO65GSSA
HEATER UNIT ASSEMBLY REMOVAL
(HEATING ELEMENT/CONVECTION FAN/CONVECTION MOTOR/THERMISTOR)
THERMISTOR REMOVAL
HEATING ELEMENT REMOVAL
1. Disconnect oven from power supply and remove outer
case cabinet.
2. Discharge the high voltage capacitor.
Disconnect wire leads from H.V. capacitor and remove
four (4) screws holding rear cabinet to bottom plate
and three (3) screws holding to heater unit assembly
and two (2) screws holding steam duct to top of oven
cavity. Disconnect wire leads from power supply cord
terminals.
3. Disconnect wire leads from thermistor. Remove two (2)
screws from thremistor.
4. Disconnect wire leads from convection motor, thermal
cut-out and heater element.
5. Remove nine (9) screws holding heater duct to the oven
cavity.
6. Remove two (2) screws holding heater duct to base
cabinet. Release two (2) snap bands holding wire harness
to the thermal cover (convection).
7. The heater unit is now free.
1. Remove two (2) screws holding heating element to heater
duct.
2. Loosen two (2) screws holding holders to heater duct and
take heating element out of heating element holders.
3. Heating element is free.
NOTE:After installed the heating element completely,
bent top of the heating element holder to inside
using by long nose pliers as shown following
illustration.
Long nose plier
Heating
element
Heating element
holder
OVEN LAMP AND LAMP SOCKET REMOVAL
Oven lamp
socket
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Bend the tab of the air guide holding the lamp socket.
4. Lift up the oven lamp socket.
5. Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
6. Now, the oven lamp socket is free.
Terminal
Wire lead
Terminal hole
Flat type small
screw driver
Figure C-2. Oven lamp socket
FAN MOTOR REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect the wire leads from the fan motor.
4. Remove one (1) screw holding the fan motor grounding
wire to the air guide (Right).
5. Remove three (3) screws holding the chassis support
to the rear cabinet, waveguide and control panel back
plate.
6. Remove the chassis support from the oven.
7. Remove one (1) screw holding the magnetron air guide
to the waveguide.
8. Remove the magnetron air guide from the waveguide.
9. Disconnect wire leads from the fan motor.
10. Release the main harness from the hole of the fan
duct.
11.Release the thermistor harness from the hole of the fan
duct.
12. Release one (1) tab holding the fan duct to the rear
cabinet.
13.Release one (1) tab holding the fan duct to the air guide
(Right).
14.Remove the fan duct assembly from the oven.
15.Remove the fan blade from the fan motor shaft according
the following procedure.
1) Hold the edge of the rotor of the fan motor by using a
pair of grove joint pliers.
CAUTION:
* Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan motor
because the rotor is easily shaven by pliers and
metal pieces may be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not disfigure the bracket by touching with the
pliers.
2) Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
3) Now, the fan blade will be free.
CAUTION:
* Do not use this removed fan blade again because
the hole (for shaft) of it may become bigger than a
standard one.
33
E30MO65GSSA
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted.
3. Reset the fan duct assembly to its place.
4. Install the tabs of fan duct to the rear cabinet and air
guide.
5. Install the magnetron air guide with the one (1) screw.
6. Reinstall the main harness and thermistor harness to
each hole of the fan duct.
7. Reinstall the chassis support to the control panel back
plate, waveguide and rear cabinet with the three (3)
screws.
8. Re-connect the wire leads to the fan motor, referring to
the pictorial diagram. 9. Re-install the fan motor grounding wire to the air guide
(Right) with one (1) screw.
16.Remove the two (2) screws and nuts holding the fan
motor to the fan duct.
17.Now, the fan motor is free.
INSTALLATION
1. Install the fan motor to the fan duct with the two (2) screws
and nuts.
2. Install the fan blade to the fan motor shaft according the
following procedure.
1) Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
2) Apply the screw lock tight into the hole (for shaft) of the
fan blade.
3) Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
* Do not hit the fan blade strongly when installed
Shaft
Coil
Groove joint pliers
Shaft
Axis
Stator
Gap
Bracket
Rotor
Table
These are the positions
that should be pinched
with pliers.
Stator
Center of
bracket
Rotor
Rear View
Side View
POWER SUPPLY CORD REPLACEMENT
Removal
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect the white and black wires of the power supply
cord from the noise filter.
4. Remove the one (1) screw holding the earth wire of the
power supply cord to the base cabinet.
5. Remove the power supply cord from the rear cabinet.
Re-install
1. Insert the power supply cord into the rear cabinet.
2. Connect the white and black wires of the power supply
cord into the terminal of noise filter, referring to the
Pictorial Diagram.
3. Re-install the earth wire of the power supply cord to the
base cabinet with the one (1) screw.
Figure C-3. Power supply cord replacement
Noise filter
GRY
RED
White wire
Power
supply cord
N
H
Black wire
Rear Cabinet
Green wire
Base Cabinet
CONTROL PANEL ASSEMBLY AND CONTROL UNIT REMOVAL
To remove the control panel, procedure as follows:
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect connector CN-A, CN-E and CN-F from the
control unit.
4. Disconnect the wire leads from the relays RY1, RY2 and
RY3.
5. Remove one (1) screw holding the control panel back
plate to the chassis support.
6. Remove two (2) screws holding the bottom edge of the
back plate to the cabinet base.
7. Remove one (1) screw holding the back plate to the oven
cavity flange.
8. Lift up and pull the control panel assembly forward.
Replacement of individual component is as follows;
CONTROL UNIT AND KEY UNIT
1. Disconnect the wire connector from the control unit.
2. Remove the four (4) screws holding the panel frame to
the back plate.
3. Separate the panel frame and back plate.
4. Remove the three (3) screws holding the control unit to
the panel frame.
5. Lift up the control unit and disconnect the key connector
from the control unit.
34
E30MO65GSSA
2. When a attaching the key unit to the control panel
frame, adjust the lower edge and right edge of
the key unit to the correct position of the control
panel frame.
3. Stick the key unit firmly to the control panel frame
6. Now, the control unit and frame assembly are
separated.
NOTE;1. Before attaching a new key unit, remove remaining
adhesive on the control panel frame surfaces
completely with alcohol and so on.
THIRD DOOR SWITCH, DOOR SENSING SWITCH, PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Remove the control panel assembly, refer to "Control
Panel Removal".
4. Disconnect wire leads from each of the switches and
fuse holder.
5. Remove two (2) screws holding latch hook to oven
flange.
6. Remove latch hook assembly from oven flange.
7. Push outward on the one (1) stopper tabs holding each
of switches place.
8. Switch is now free.
At this time switch lever will be free, do not lose it.
Re-install
1. Re-install switch lever and each interlock switch in its
place. The primary interlock switch is in the lower position
and the door sensing switch and thir door switch are in
the upper position and the monitor switch is in the middle
position.
2. Re-connect wire leads to each switches and fuse
holder.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to
oven flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and Adjustment procedure.
THIRD DOOR SWITCH, DOOR SENSING SWITCH, PRIMARY
INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
latched position.
2. The door sensing switch and primary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. The third door switch contacts open when the door is
opened.
5. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
If the door sensing switch, third door switch, primary interlock
switch and monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
1. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
2. With door closed, adjust latch hook by moving it back
and forth, and up and down. In and out play of the door
allowed by the latch hook should be less than 0.5mm.
The vertical position of the latch hook should be adjusted
so that the door sensing switch and primary interlock
switch are activated with the door closed. The horizontal
position of the latch hook should be adjusted so that the
plungers of the monitor switch and the third door switch
are pressed with the door closed.
3. Secure the screws with washers firmly.
4. Check the all switches operation. If each switch has not
activated with the door closed, loosen the screw and
adjust it.
LATCH HOOK
THIRD DOOR SWITCH
DOOR SENSING
SWITCH
LATCH
HEADS
MONITOR SWITCH
PRIMARY
INTERLOCK SWITCH
SWITCH LEVER
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm at the
OPEN LEVER
DOOR OPEN
BUTTON
Figure C-4. Latch Switch Adjustments
DOOR REPLACEMENT AND ADJUSTMENT
REMOVAL
1. Disconnect oven from power supply and remove the
outer case.
Remove turntable tray and turntable support from oven
cavity.
2. Remove three (3) screws holding lower oven hinge.
3. Remove the lower oven hinge from oven cavity bottom
flange.
4. Remove door assembly from upper oven hinge on the
oven.
5. Door assembly is now free.
Note: When the individual parts are replaced, refer to
"Door Disassembly".
6. On re-installing door, insert the upper oven hinge into
the door hinge pin. Then while holding door in place.
35
E30MO65GSSA
7. Make sure the door is parallel with oven face lines (left
and upper side lines) and door latch heads pass through
latch holes correctly.
8. Insert the lower oven hinge into oven cavity bottom flange
and then engaged the door hinge pin. Then secure the
lower oven hinge firmly with tree (3) mounting screws.
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter "Test Procedures".).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
cycle. This function does not require that door be
airtight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves
indicate a leakage of microwave energy from oven
cavity. If such were the case, your oven could not be
equipped with a vent, the very purpose of which is to
exhaust the vapor-laden air from the oven cavity.
UPPER OVEN HINGE
DOOR ADJUSTMENT
The door can be adjusted by keeping screws of each hinge
loose.
RE-INSTALL
After adjustment, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Note: The door on a microwave oven is designed to act
as an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
DOOR ASSEMBLY
LATCH
HEADS
LOWER OVEN HINGE
RE-INSTALL
Figure C-5. Door Replacement and adjustment
DOOR DISASSEMBLY
2 LIFT UP
Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
1. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door panel
are provided at several places, do not force any particular
part.
2. Insert an putty knife (thickness of about 0.5mm) into the
gap between the choke cover and corner portion of door
panel as shown Figure C-6 to free engaging parts.
3. Lift up choke cover.
4. Now choke cover is free from door panel.
PUTTY KNIFE
1 BENT
CHOKE COVER
Door Bent
Panel
INSIDE Choke
cover
Upper
Lower
FRONT
Figure C-6. Door Disassembly
36
E30MO65GSSA
MICROWAVE MEASUREMENT PROCEDURE
Leakage test:
After adjustment of the door, interlock and monitor switches
are completed individual or collectively, interlock switch test
and microwave leakage test must be performed with survey
instrument and test results must be confirmed to meet the
requirement of the performance standard for microwave
ovens as undermentioned.
Leakage Test with Enclosure Installed.
1. Grasp the probe of the survey instrument and hold it
perpendicular to the gap between the door and the body
of the oven.
2. Move the probe slowly, not faster than 2.5cm/sec. along
the gap, watching for the maximum indication on the
meter.
3. Check for leakage at the door screen, sheet metal seams
and other accessible positions where the continuity of
the metal has been breached (eg., around the switches,
indicator, and vents).
4. Measure carefully at the point of highest leakage and
make sure that the highest leakage is no greater than
4mW/cm2, and that the primary interlock switch does
turn the oven OFF before any door movement.
Requirement
Every microwave oven shall function in such a manner
that when the oven is fully assembled and operating with
it’s service controls and user controls adjusted to yield
the maximum output, the leakage radiation, at all points
at least 5 cm. from the external surface of the oven, does
not exceed:
1.1.0mW/cm2 with the test load, 275±15ml of water at an
initial temperature of 20±5οC.
2. 5.0mW/cm2 when the outer enclosure is removed with
a test load of 275±15ml water at an initial temperature
of 20±5οC.
Leakage Test without Enclosure.
1. Remove the enclosure (cabinet).
2. Grasp the probe of the survey meter and hold it
perpendicular to all mechanical and eleeectronic parts
of the oven that is accessible to the user of the oven
including, but not limited to, the waveguide, cavity,
cavity seams, magnetron and magnetron to waveguide
connection.
3. Move the probe slowly (not faster than 2.5cm/sec.),
watching for the maximum indication on the meter.
4. Measure carefully at the point of highest leakage and
make sure that the highest reading is under the required
limit as mentioned above.
3. 5.0mW/cm2 without a test load.
Preparation For Testing:
Before beginning the actual measurement of leakage,
proceed as follows:
1. Make sure that the actual instrument is operating normally
as specified in its instruction booklet.
Note: Survey instruments that comply with the requirement
for instrumentation as prescribed by CSA and NHW
performance standard for microwave ovens must be
used for testing.
CAUTION !
Recommended instruments are:
NARDA 8100
NARDA 8200
Special attention should be given to avoid electrical
shock because HIGH VOLTAGE is generated during
this test.
2. Place the oven tray in the oven cavity.
3. Place the load of 275±15 ml of tap water initially at
20±5οC in the center of the oven cavity.
The water container shall be a low form of 600 ml beaker
with an inside diameter of approx. 8.5 cm and made of
an electrically nonconductive material such as glass or
plastic.
The placing of this standard load in the oven is important
not only to protect the oven, but also to insure that any
leakage is measured accurately.
No Load Test
1. Operate the oven without a load and mesure the leakage
by the same method as the above test procedure “A. Test
Enclosure Installed”.
2. Make sure that the highest leakage should not exceed
5mW/cm2.
Note: Do not perform this test for extended periods.
4. Close the door and set the time cooking for several
minutes. And start the oven. If the water load is depleted
replace it.
37
H
1
2
3
38
4
7
9
1
3
5
CN-A
RY6
RY4
RY5
RY1
COM.
RY2
CN-E
T1
6
5
4
3
2
1
ORG
BLK
RY2 (N.O.)
RY1 (COM.)
5
9 WHT
BRN
RED
N.O.
COM
PRIMARY
INTERLOCK
SWITCH
COM
ORG
MONITOR
SWITCH
WHT
N.C.
GRN
ORG
R
E
D
PNK
GRY
G
R
Y
TURNTABLE
MOTOR
G
R
Y
HEATING
ELEMENT
COM
N.O. DAMPER
SWITCH
PNK
PNK
PNK
NOTE:
Hot (YLW & PNK) wire
must be connected to the
terminal with blue mark
on the oven light socket.
PNK
ORG
RED 2 RED
RED 1 RED
THERMISTOR
CONVECTION MOTOR
DAMPER
MOTOR
WHT
BRN
GRY
G
R
Y
BLK
WHT
RED
NOISE FILTER
AND FUSE
H
N
GRY
O
R
G
G
R
Y
HIGH VOLTAGE
CAPACITOR
W
H
T
P
P
L
GRN
BLK
WHT
RED
PNK
CONV.
THERMAL
CUT-OUT
POWER SUPPLY CORD
COOLING
FAN
MOTOR
NOTE:
Hot (ORG) wire must be connected to the
power transformer terminal nearest to the
transformer mounting screw.
POWER TRANSFORMER
RED
5
E
Figure S-1. Pictorial Diagram
GRN
GRN
BLUE MARK
GRY
BLK
4
3 BRN
4
5 PPL
6
7
8
1 ORG
2
CN-A
PNK
RED
BRN
RY2 (COM.)
RY1 (N.O.)
RED
RY3 (N.O.)
RY3 (COM.) BRN
5 PNK
4 RED
3 RED
2 GRN
1 ORG
6 PNK
CN-E
COM
N.O.
COM
WHT
PNK
MAGNETRON
THERMAL
CUT-OUT
BLK
3
N.O.
N.O.
COM.
RY3
COM.
CN-F
1
3
IC-1
DOOR
SENSING
SWITCH
WHT
GRY
GRY
BLK
RED
2
N.O.
CN-G
AH SENSOR
G
OVEN
THERMAL
CUT-OUT
C
N.O.
D
BLK
MAGNETRON
1
CONTROL PANEL
CN-F
1 BLK
2 RED
3 WHT
F
GRY
B
THIRD
DOOR
SWITCH
OVEN LAMP
& SOCKET
A
HIGH VOLTAGE COMPONENTS
E30MO65GSSA
6
A
B
C
6
D
E
F
G
H
3
39
OVEN LAMP
TURNTABLE
MOTOR
HEATING
ELEMENT
4
COM
NO
COM
NO
COM
NO
A5
FAN
MOTOR
POWER
TRANSFORMER
A3
A1
CONV.
MOTOR
DAMPER
MOTOR
A7
c
(J1)
10G471K
RY1
RY3
RY2
RY6
RY5
RY4
4
D2
D3
D23
C2 1000µ/35v
C1 0.1µ/50v
+
–
Q22
KRA101M
Q21
KRA101M
Q20
KRA101M
R3 330 1/2w
Q1
2SB1238
C11
5
C3 0.1µ/50v
C50
DAMPER
SWITCH
E6
C60
Q40
KRA101M
C5 0.1µ/50v
R51 4.7k
E5
–
HZ4A2
Q3
KRA101M
E4
OVEN
THERMISTOR
E3
R62 27kF
F1
(A)
(C)
F3
AH SENSOR
F2
(B)
CF1 4.19MHz
VCC 1
VEE
AVSS
VREF
AN7
AN6
AN5
AN4
AN3
AN2 10
AN1
AN0
P55
P54
P53 15
P52
P51
P50
P47
P46 20
P45
P44
P43
P42
INT1 25
P40
RST
XCIN
XCOUT
XIN 30
XOUT
VSS 32
R90 100k
P30
P31
P32
P33
P34
P35
P36
P37
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
P22
P23
P24
P25
P26
P27
C70 330pF x 4
33
35
40
45
50
55
60
64
1
Q90
KRA101M
(VP)
C10 0.1µ/50v
G1
G2
G3
12
G6
G7
SENSOR
ADD A
DEFROST
COOK
MINUTE
G5
(A)
(VP)
SENSOR
DEFROST
MIX CONV
KEY UNIT
HELP
REHEAT
SLOW
COOK
LOW MIX
BAKE
POPCORN PREHEAT
CONVEC
BAKE
(B)
G4
(C)
IC2 IZA495DR
F 31, 32
F
1, 2
8G
29
NOTE
COOK
LBS
OZ
FLUORESCENT DISPLAY TUBE
0
450°F
STOP
CLEAR
9
425°F
START
TOUCH ON
8
400°F
CLOCK
7
375°F
POWER
LEVEL
6
350°F
TIMER
5
325°F
4
300°F
275°F
150°F
100°F
BROIL
G12
3
2
1
G11
AUTO
BAKE
AUTO
ROAST
AUTO
BROIL
HELP
HIGH MIX
ROAST
G10
G9
G8
KG
: IF NOT SPECIFIED. 1SS270A
: IF NOT SPECIFIED. 0.01µ/16v
: IF NOT SPECIFIED. 1/4w ± 5%
5
6
Figure S-2. Control Panel Circuit
E2
DOOR
SWITCH
E1
R31 4.7k
C30
Q23
KRA101M
+
–
R4 750 1/2w
–
+
Q4
DTA123ES
4
D30
Q26
KRC243M
Q25
KRA223M
Q24
KRA223M
–
ZD2
470 1/2w
+
(J2)
+
ZD3
R50 15k
HZ16-1
SP40
22µ
/25v
C4 10µ/35v
R40 3.3k
C21 0.1µ/50v
HZ5C2
C9 0.01µ/50v
(J4) 15k
R2
C20 10µ/35v
ZD4
D4
(J6)
R8 4.7k
(J5) 6.8k
VRS1
a
(J7)
b
C8
R64 3.3kF
D1-4 : 11ES1
C7
D1
R7 4.7k
5
IC1 IXA103DR
3
R70 3.3k
d
R71 3.3k
R11 18 1w
R72 3.3k
R10 18 1w
R73 3.3k
CONTROL UNIT
R100 330 1w
+
28
27
7G
6G
C22 0.1µ/50v
–
26
5G
D7
100k
R92
D20
D21
D22
D24
D25
D26
100k
R93
25
4G
D72 R76
3.3k
24
23
22
3G
2G
1G
AC120V
60Hz
7
P16 20
8
P13 17
T1
P15 19
P14 18
D73 R77
3.3k
1
3
R30 15k
P12 16
C6 10µ/35v
(J3)
R63 220F
100k
R91
D70 R74
3.3k
C
D71 R75
3.3k
2
D31
P11 15
P10 13
P9 12
2
D75 R79
3.3k
1
9
H
11
10
G
P8
P7
F
P6
E
8
7
6
5
4
D
D76 R80
3.3k
B
D74 R78
3.3k
A
P5
P4
P3
P2
P1
1
D77 R81
3.3k
A9
E30MO65GSSA
6
A
B
C
D
E
F
G
H
E30MO65GSSA
1
2
4
3
5
6
R
A
1
DIP
,F
B
E
Q90
1
2
R91
R92
R93
(ONLY
PHR)
(CF1)
(R45)
(C45)
C7
R7
R8
C8
3
E
5
C
B
Q4
B
Q3
1
R79
R78
R77
R76
R75
12
6
C9
(R47)
(R48)
R64
9
C5
(R49)
(C46)
C6
4
(C47)
IC3
1
1
8
C30
C50
C60
13
5
(R46)
CN - G
IC2
10
11
12
(J7)
(J5)
(J3)
3
(J2)
(J4)
(J6)
D
14
R40
1
CN - F
15
16
CONV
HEATER COM
17
18
E
B
C3
D31
D30
1
C4
E
E
D21
C1
D3
D4
D1
D2
B
D20
F
4
1
S1
1
5
P
VRS1
3
5
7
DAMP M CONV M FAN M
RY4
E
Q22
25
Q20
F
C20
E
BE
Q26
23
24 B
ZD2
R2
D26
BLK
C22
B
Q21
21
C2
22
RY5
E
B
B Q23
20
RY1
POWER
PINK RED (BRN
OL TTM
RED)
R3
E
Q1
D23
RY2
DOOR
SW
Q24 E
3 2
Q25
CN - E
B
OVEN
TEMP
R62
ORG
POWER TRANS
19
E
B
5 4
R63
R50
R51
Q40
C21
D24
RY3
DAMP
SW
R4
D25
6
BRN
R31
R30
RED
1
64
8
R100
12
D
ZD3
ZD4
7
12
R74
S2
3
8
T1
9
D7
26
POWER
(J1)
7
G
CN - A
G
1
(CN - D)
4
E
IC1
(CN - G)
(ONLY 9X58PJ)
C
E
B
(C80)
CF1
(R85)
1
D70
D71
D72
D73
D74
D75
D76
D77
C10
(C81)
R86(J8)
32
33
R73
R72
R71
R70
3
R90
R80
R81
C70
B
A
32
D22
C11
R10
RY6
R11
0
H
H
Figure S-3. Printed Wiring Board
1
2
4
3
40
5
6
E30MO65GSSA
PARTS LIST
Refer to "IMPORTANT" described at end of parts list.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
ELECTRICAL PARTS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
FACCDA074WRE0
FFS-BA012WRK0
FPWBFA389WRKZ
QSW-MA131WRE0
FH-HZA041WRE0
QSW-MA110WRE0
RTHM-A078WRE0
RTHM-A121WRE0
RMOTDA192WRE0
RLMPTA093WRZZ
QSOCLA021WRE0
RMOTEA283WRE0
RMOTEA300WRE0
RHET-A136WRE0
RTRN-A527WRE0
RC-QZA211WRE0
FH-DZA053WRK0
RV-MZA348WRZZ
RMOTDA222WRE0
FDTCTA183WRK0
Power supply cord
Monitor fuse 20A and monitor switch (V-5220D-070) assembly
Noise filter Primary interlock switch/Thirdoor switch/Door sensing switch
Thermistor Damper switch
ο
Magnetron thermal cut-out
125 C
ο
Oven & Convection thermal cut-out 150 C
Damper motor
Oven lamp
Oven lamp socket
Convection fan motor Fan motor Heating element Power transformer
H.V.capacitor (Interchangeable)
H.V.rectifier assembly Magnetron
Turntable motor AH sensor assembly 21
22
23
24
25
26
27
28
29
30
31
GCABUB035WRPZ
FDAI-A199WRY0
GLEGPA019WRE0
GCABDA094WRW0
LHLDKA009WRF0
LBNDKA036WRP0
FHNG-A320WRMZ
PHOK-A137WRFZ
MLEVPA231WRF0
GCOVHA347WRP0
PCOVPA171WRP0
Outer case cabinet
Base cabinet (Not Replaceable)
Foot Rear cabinet (Not Replaceable)
Cord holder Capacitor holder Oven hinge (Lower)
Latch hook
Switch lever Turntable motor cover CSA barrier 32 33
34
35 36 37 38 39
40
41
42
DPWB-A450DRKZ
DPNLCB168MRK0
FUNTKB491MRE0
JBTN-B212WRF0
MSPRCA045WRE0
LANGTA340WRW0
FANGTA093WRK0
NSFTTA042WRE0
XEPSD30P10XS0
XCPS740P12000
LX-CZB019MRE0
Control unit
Control panel frame with key unit Key unit Open button Open button spring Control panel back plate Open lever Open shaft
Screw ; control unit mtg.
Screw ; control panel back plate mtg.
Screw ; control panel mtg.
1
1
1
3
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
CABINET PARTS
1
1
4
1
1
1
1
1
1
1
1
CONTROL PANEL PARTS
1
1
1
1
1
1
1
1
3
5
2
OVEN PARTS
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
FOVN-A314WRY0
FROLPA072WRK0
NTNT-A128WRHZ
FBRGMA004WREZ
PREFHA028WRW0
LANGTA415WRWZ
LBNDK0054WRE0
LFIX-A013WRW0
NFANMA019WRW0
NPLYBA021WRF0
FDUC-A279WRK0
PFPF-A138WRE0
LANGKA723WRP0
PCUSUA167WRP0
PCUSUA424WRP0
FDUC-A323WRW0
MCAMPA030WRF0
NSFTTA114WRE0
FFTA-A034WRK0
PDUC-A269WRW0
PCUSGA398WRP0
Oven cavity assembly (Not Replaceable)
Turntable support Turntable tray
Bearing ass’y
Thermal protection plate (left) Bearing mounting plate Heater element holder Bearing holder plate
Convection fan
Pulley (F)
Heater duct assembly
Thermal protection sheet (left) Glass mounting plate Cushion Cushion Steam duct assembly Damper cam
Damper shaft
Damper door ass’y
Damper duct
Cushion 41
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
AY
AC
AB
AM
AK
AC
E30MO65GSSA
REF. NO.
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85
PART NO.
NCPL-A021WRF0
PCOVPA301WRE0
PCUSUA196WRP0
PGLSPA455WRE0
PFPF-A139WRE0
PREFHA053WRW0
PSKR-A153WRW0
PSKR-A323WRW0
LANGQA407WRW0
NPLYBA021WRF0
NFANJA020WRE0
PDUC-A882WRFZ
LANGFA089WRW0
MHNG-A520WRMZ
NBLTKA005WRE0
LANGQA474WRP0
PCUSUA196WRP0
PCUSUA425WRP0
PCUSGA353WRP0
PSKR-A171WRW0
PFPF-A064WRE0
PCOVPA304WRP0
DESCRIPTION
Turntable coupling Waveguide cover
Cushion Light glass Thermal protection sheet (Right)
Thermal protection plate (Right)
Air guide (Bottom) Air guide (Right) Convection motor mounting plate Pulley (M)
Fan blade
Cooling fan duct
Chassis support
Oven hinge (Upper) Convection fan belt Noise unit angle
Cushion
Damper duct cushion Cushion Magnetron air guide Thermal protection sheet Thermo cover Q'TY
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
CODE
AE
AE
AD
AD
AF
AP
AK
AF
AG
AC
AE
AL
AE
AE
AF
AG
AD
AG
AH
AE
AF
AF
1
1
1
1
1
1
1
1
6
12
1
BT
BD
AP
AF
AH
AA
AA
AA
AA
AA
AD
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AW
AW
AN
BB
AN
AF
AB
AD
AQ
AC
AH
AH
AH
14
4
2
4
2
1
1
6
1
2
7
7
1
2
1
6
3
1
3
1
4
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AB
AA
DOOR PARTS
86
87
88
89
90
91
92
93
94
95
96 FCOV-B363MRK0
DDORFA820WRY0
GCOVHA155WRF0
LANGKA851WRT0
LSTPPA244WRFZ
MSPRTA192WRE0
LANGKA918WRW0
LANGKA919WRW0
XCPS740P08000
XEPS730P08000
PCUSGA537WRPZ
Door frame assembly
Door panel Choke cover Latch angle Latch head Latch head spring Thermal plate U Thermal plate R Screw; 4mm x 8mm Screw; 3mm x 8mm Cushion 97
98
99
100
101
102
103
104
105
106
107
108
109
110
FAMI-A088WRM0
FAMI-A087WRM0
FW-VZB342WRE0
FW-VZB880WREZ
QW-QZA198WRE0
QW-VZA108WRE0
TCAUAA196WRR0
TCAUAB060MRR0
TINSEB471MRR0
LHLDWA013WRE0
TCAUHB011MRR0
TCAUSB012MRR0
TCAUAB048MRR0
TCAUAB033MRR0
Low rack (Broiling trivet) High rack (Baking rack) Thermistor harness Main wire harness High voltage wire B Grounding wire (Cooling fan motor)
Monitor caution label NHW caution label Operation manual
Purse lock LL
User caution BIK label
GND caution label
UL screw label
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
XOTWW40P10000
XOTSE40P12000
XCTWW40P08000
XHTSD40P08RV0
LX-CZ0052WRE0
XWVSD60-07000
LX-WZA004WRE0
LX-CZA020WRE0
XBPSD30P14K00
XBPSD40P25000
XBTWW40P06000
XCTSD40P08000
LX-NZ0029YBE0
XBPSD40P06KS0
LX-WZA022WRE0
LX-BZ0531FCZZ
XCPSD30P06000
LX-CZA038WRE0
XFPSD40P08K00
XBPSD40P06000
XCBWW30P06000
Screw; 4mm x 10mm
Screw; 4mm x 12mm
Screw; 4mm x 8mm
Screw; 4mm x 8mm
Special screw Washer; 6mm x 0.7
Washer
Special screw Screw; 3mm x 14mm
Screw; 4mm x 25mm
Screw; 4mm x 6mm
Screw; 4mm x 8mm
Special nut
Screw; 4mm x 6mm
Washer
Screw; 4mm x 8mm
Screw; 3mm x 6mm
Special screw Screw; 4mm x 8mm
Screw; 4mm x 6mm
Screw; 3mm x 6mm
MISCELLANEOUS
SCREWS NUTS AND WASHERS
42
mm E30MO65GSSA
REF. NO.
132
133
134
135
136
137
138
139
PART NO.
XFPSD40P08000
XFPSD60P14JS0
XOTSD40P12000
XFPSD30P08000
XNESD40-32000
XNEUW40-32000
XWSUW40-10000
LX-CZA070WRE0
DESCRIPTION
Screw; 4mm x 8mm Screw; 6mm x 14mm Screw; 4mm x 12mm Screw; 3mm x 8mm Nut; 4mm x 3.2mm
Nut; 4mm x 3.2mm
Washer; 4mm x 1 mm
Screw; UL 43
Q'TY
6
2
21
2
2
1
1
2
CODE
AA
AB
AA
AA
AA
AA
AA
AA
52
1
2
3
44
72
134
73
5
4
44
31
5
79
2
123
114
111
30
117
130
132
126
19
114
70
115
28
A
134
29
7
4
23
x4
2
63
4
26
129
103
132
x3
84
17
4
1
16
134
134 x4
129
25
x2
80
56
68
18
134
69
24
120
110
114
104
59
116
60
1
82
81
102
15
108
133
109
9
127
126
6
119
62
13
136
112
61
126
83
75
A
57
129
112
128
74
5
134
118
x3
111
27
22
80
71
102
122 x4
112
4
3
114
121
64
43
137
x3
138
118
77
126
99
132
58
126
134
3
45
TO OVEN
BASE PLATE
65
12
121
51
131
14
66
20
67
134
2
124
131
131
53
x3
55
D
111
56
49
54
F
123
66
139
A
78
111
x3
E
8
46
47
10
76
21
C
125
50
135
11
134
1
127
48
H
113
8
85
139
E30MO65GSSA
6
OVEN AND CABINET PARTS
A
B
B
C
G
6
D
E
F
G
H
E30MO65GSSA
2
1
4
3
6
5
CONTROL PANEL PARTS
41
A
A
37
32
107
33
38
134
B
B
40
34
42
39
41
114
C
C
35
36
D
D
95
88
DOOR PARTS
87
96
E
92
E
94
86
94
89
94
90
F
F
94
93
91
MISCELLANEOUS
G
G
97
100
99
98
106
Actual wire harness may be different than illustration.
H
H
101
102
1
2
4
3
45
5
6
E30MO65GSSA
2
1
4
3
6
5
PACKING AND ACCESSORIES
A
A
TRAY HOLDER
TOP PAD ASSEMBLY
B
B
DOOR PROTECTION SHEET
45 TURNTABLE TRAY
PLASTIC BAG
105 OPERATION
MANUAL
C
C
MICROWAVE OVEN
44 TURNTABLE SUPPORT
BOTTOM PAD ASSEMBLY
D
D
TRAY PACKING FOAM
PACKING CASE
Not replaceable items.
E
E
F
F
G
G
H
H
1
2
4
3
46
5
6
E30MO65GSSA
NOTES:
47
E30MO65GSSA
ELECTROLUX
COPYRIGHT © 2007 BY ELECTROLUX HOME PRODUCTS, INC.
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in retrieval systems, or transmitted
in any form or by any means, electronic,
mechanical, photocopying, recording, or
otherwise, without prior written permission
of the publisher.
48