DMP Electronics Vortex86MX PMX-089T-8A User`s manual

PMX-089T-5A / PMX-089T-8A

PMX-089T-5A-512 / PMX-089T-8A-512

DM&P Vortex86MX Panel PC with 8.9” TFT LCD

User’s Manual

Copyright

The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep current the information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the DMP Electronics Inc.

Trademarks Acknowledgment

Vortex86MX  is the registered trademark of DMP Electronics Inc. Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only.

Safety Information

 Read these Safety instructions carefully.

 Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

 Do not expose your Panel PC to rain or moisture, in order to prevent shock and fire hazard.

 Keep PMX-089T away from humidity.

 Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for qualified personnel servicing.

 Never touch un-insulated terminals or wire unless your power adaptor is disconnected.

 Locate your Panel PC as close as possible to the socket outline for easy access and to avoid force caused by entangling of your arms with surrounding cables from the Panel

PC.

 USB connectors are not supplied with Limited Power Sources.

 If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

D O NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS

(E NCASING ) OF THIS PRODUCT .

P LEASE CONTACT YOUR DEALER FOR

SERVICING FROM QUALIFIED TECHNICIAN . ii

T a b l e o f C o n t e n t s

T a b l e o f C o n t e n t s ............................................................. iii

C h a p t e r 1 General Information..…………………………………1

1.1 Product Description ................................................ 1

1.2 Product Specifications ............................................ 2

1.3 Inspection standard for TFT-LCD Panel ................. 4

1.4 Product Dimension ................................................. 7

1.5 Ordering Information .............................................. 8

1.6 Packing List ............................................................ 8

C h a p t e r 2 System Installation ................................................. 9

2.1 CPU Board Outline ................................................. 9

2.2 Connector Summary ............................................ 10

2.3 Connector Pin Assignments ..................................11

2.4 External I/O Overview .......................................... 14

2.5 External I/O Pin Assignment ................................. 15

2.6 System Mapping ................................................... 17

2.7 Watchdog Timver ................................................. 20

C h a p t e r 3 Driver Installation…..………………………………..21

3.1 PMX-089T Development Note .............................. 22

3.2 BIOS Defaul Setting ............................................. 23

Warranty ............................................................................................ 24

C h a p t e r 1

General Information

1.1 Product Description

PMX-089T is an ultra compact platform for the present demanding embedded and productive applications. It has new Vortex86MX SoC CPU which consumes only minimum power requirement when running at 1GHz, and DDR2 memory provides faster data transfer rate. By using 8.9” TFT LCD, PMX-089T becomes the perfect choice for a limited budget. In additional, the integrated 10/100M Ethernet port supplies the communication capability which makes

PDX-089T can be more widely used when running with Linux, Windows CE, and Windows XP environment to become the perfect solution for system integration.

 8.9” WSVGA TFT LCD

 4-Wire Resistive Touch Panel

 DM&P Vortex86DX SoC 1GHz

 512MB/1GB DDR2 system memory

 AMI BIOS

 2 watchdog timer

 Compact Flash Type I/II / Micro SD

 10/100Mbps Ethernet

 2 USB 2.0 (host)













1 RS-232/485/422 ports

Wi-Fi Optional

Audio Out

Single voltage +5V DC(5A Version)

Multi voltage +8~+35V DC(8A Version)

Fanless Design

 Operating temperature range of 0°C to

+50°

1.2 Product Specification

CPU Board Specifications

CPU DM&P Vortex86MX 1GHz

Cache

BIOS

Memory

L1:16KB I-Cache, 16KB D-Cache

L2: 256KB Cache

AMI BIOS

Watchdog Timer

LAN

Audio

512MB/1GB DDR2 onboard

Software programmable from 30.5u to 512 seconds x 2 sets

Integrated 10/100M Ethernet

HD Audio-Realtek ALC262 CODEC

Internal Drives

Compact Flash Type I/II slot

Micro SD slot

I/O

RS-232/422/485 x 1

USB ports (Ver2.0) x 2

RJ-45 Port x 1

Mechanical & Environment

Single Voltage +5VDC ( 5A )

Power Requirement

Multi Voltage +8~+35VDC ( 8A )

Power Consumption 1.5A@5VDC

Operating Temperature 0 ~ +50 ℃ ( 32 ~ +122 ℉)

Storage Temperature -10 ~ +60 ℃ ( 14 ~ +140 ℉)

Operating Humidity

Dimensions

0% ~ 90% relative humidity, non-condensing

236.6 x 146 x 35mm (9.31 x 5.75 x 1.38 inches)

Weight 468g

Front Panel Protection IP 65

Certification CE, FCC, VCCI, Vibration

PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD 2

LCD Specifications

Display Type

Backlight Unit

Display Resolution

Brightness (cd/m 2 )

Contrast Ratio

Display Color

Pixel Pitch (mm)

Viewing Angle

8.9” TFT LCD

LED

1024(W) x 600(H)

220 nits

500:1

262,144

190.5 (H) x 189 (V)

Vertical 110 o ,

Horizontal 140 o

25,000 hrs Backlight Lifetime

Touchscreen

Type

Resolution

Transmittance

Controller

Software Driver

Durability

Analog Resistive

Continuous

80%

PS/2 interface

DOS/Linux/WinCE/WinXP

1 million


1.3 Inspection standard for TFT-LCD Panel

DEFECT TYPE LIMIT Note

VISUAL

DEFECT

INTERNAL

SPOT

FIBER

POLARIZER BUBBLE

Mura

φ＜0.15mm Ignore

0.15mm≦φ≦0.5mm N≦4

0.5mm＜φ N=0

0.03mm<W≦0.1mm, L≦5mm N≦3

1.0mm＜W, 1.5mm＜L N=0

φ＜0.15mm Ignore

0.15mm≦φ≦0.5mm N≦2

0.5mm＜φ N=0

It’ OK if mura is slight visible through 6%ND filter

Note1

Note1

Note1

ELECTRICAL

DEFECT

BRIGHT DOT

DARK DOT

TOTAL DOT

TWO ADJACENT DOT

THREE OR MORE

ADJACENT DOT

LINE DEFECT

A Grade B Grade

C Area O Area Total C Area O Area Total Note3

N≦0 N≦2 N≦2 N≦2 N≦3 N≦5 Note2

N≦2 N≦3 N≦3 N≦3 N≦5 N≦8

N≦0

N≦4 N≦5 N≦6 N≦8 Note2

N≦1 pair

N≦1 pair

N≦1 pair

N≦1 pair

N≦1 pair

Note4

NOT ALLOWED

NOT ALLOWED

(1) One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot)

(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter

(3) If require G0 grand (Total dot N≦0), please contact region sales.


[Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter

[Note2] Bright dot is defined through 6% transmission ND Filter as following.


[Note3]

C Area: Center of display area

C Area: Outer of display area

[Note4]

Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity.

(1) The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties.

(2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.


1.3 Product Dimension


1.4 Ordering Information

Part Number Description

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/Power Adapter

PMX-089T-5A-512

PMX-089T-8A-512

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/8-35 DC support

8.9” Panel PC w/512MB

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/Power Adapter

8.9” Panel PC w/512MB

DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/8-35 DC support

1.5 Packing List

Part Number

PMX-089T-5A  PMX-089T-5A

 Power-20W-3PIN

PMX-089T-8A

PMX-089T-5A-512

PMX-089T-8A-512

WLAN KIT (Optional)

Package

 PMX-089T-8A

 PMX-089T-5A-512

 Power-20W-3PIN

 PMX-089T-8A-512

 USB-WLANIPEX-KIT

 WIRELESS-ANTENNA-157

 WIRELESS-CABLE-150MM


C h a p t e r 2

System Installation

2.1 CPU Board Outline


2.2 Connector Summary

Summary Table

Nbr Description Type of Connections Pin nbrs.

J1 CF Master/Slave Switch Slide Switch

J3 USB External USB Connector

On/OFF

6-pin

J4 USB

J5 USB (Touchscreen)

External USB Connector

2.0mm 5-pin wafer

J8 PS/2 Keyboard 2.54mm 5-pin box header

J9 PS/2Keyboard/Mouse External Mini DIN Socket

6-pin

5-pin

5-pin

6-pin

J10 COM2(RS232/422/485) External D-Sub Male Connector

J14 VGA 2.0mm 10-pin box header

J18 Micro SD Card Socket Micro SD socket

J23 Audio Line-Out 1.25mm Phone Jack

J24 Audio Mic-In

J25 COM3 (TX, RX)

2.0mm 4-pin wafer

1.25mm 3-pin wafer

J26 COM4 (TX, RX 1.25mm 3-pin wafer

J30 SOM CPU Board Socket SOM CPU Board Socket

9-pin

10-pin

4-pin

3-pin

3-pin

200-pin

J31 4-Wires Touch connector 1.25mm 4-pin wafer

J32 USB (Wi-Fi Optional) Internal USB Connector

RJ45 Ethernet External RJ45 Connector

PWR Power Connector (5A) External Mini DIN Socket

PWR Power Connector (8A) External Power Plug

CF1 CF Card Socket CF Type I/II Socket

4-pin

6-pin

8-pin

3-pin

2-pin


2.3 Connector Pin Assignments

J1: CF Master/Slave Switch

Pin # Signal Name

On Master

OFF Slave

J3: USB

Pin # Signal Name Pin # Signal Name

1 VCC

4 GND

5 GND

J4: USB


1 VCC

4 GND

5 GND

J5: USB (Optional)


1 VCC

2 USBD1-

3 USBD1+

4 GND

5 GND

J8: PS/2 Keyboard


1 KBCLK

3 NC GND

5 VCC

J9: PS/2 Keyboard/Mouse


1 KBCLK


4

5 MSDATA 6 VCC

8

9 GND

J10: COM1 RS232/422/485 (Change setting by BIOS)


1 DCD1/ 422TX- / RS485- 2 RXD1 / 422TX+ / RS485+

3 TXD1 / 422RX+ 4 DTR1 / 422RX-

5 GND 6 DSR1

7 RTS1 8 CTS1

9 RI1

J14: VGA

Pin #

Signal

Name

Pin #

Signal

Name

7 HSYNC 8 GND

9 VSYNCD 10 GND

J24: MIC-IN


1 MICVREF

2 GND

3 GND

4 MIC-IN

J25: COM3 (TX, RX)


1 GND

2 TXD3

3 RXD3


J26: COM4 (TX, RX)


1 GND

2 TXD4

3 RXD4

J31: 4-Wires Touch connector


1 Y-

2 X-

3 Y+

4 X+

J32: USB (WiFi Optional)


1 VCC

4 GND

5 GND

PWR: Power Connector (5A)


1 +5V

2 GND

3 NC

4 GND

PWR: Power Connector (8A)


1 + 8 ~ 35V

2 GND


2.4 External I/O Overview

PMX-089T-8A/ PMX-089T-8A-512 PMX-089T-5A/ PMX-089T-5A-512

(Note1: Wireless is optional)

(Note2: COM1 RS232/422/485 is selected by BIOS setting)


2.5 External I/O Pin Assignment

Power Switch

Pin # Status

| ON

O OFF

Power Connector (5A)

Pin #

Signal Name

1 +5V

2 GND

3 NC

Power Connector (8A)

Pin #

1

Signal Name

+8 ~ 35V

2 GND

J10: COM1 RS232/422/485 (Change setting by BIOS)

1

3

5

7

9


DCD1/422TX-/RS485- 2 RXD1/422TX+/RS485+

TXD1 / 422RX+ 4 DTR1 / 422RX-

GND 6 DSR1

RTS1 8 CTS1

RI1


Audio Line-Out

Pin #

Signal

Name

1 GND

2 LOUTL

5 VREFOUT

USB


1 VCC

2 USB0-

3 USB0+

4 GND

5 GGND

6 GGND

RJ45


PS/2 Keyboard/Mouse


1 KBCLK

2 PMCLK

3 GND

4 KBDAT

5 PMDAT

6 SB5V


2.6 System Mapping




2.7 Watchdog Timer

There are two watchdog timers in PMX-089T, we also provide DOS, Linux and WinCE example for your reference. For more technical support, please visit: www.compactpc.com.tw or download the PDF file: http://www.compactpc.com.tw


C h a p t e r 3

Driver Installation

VGA

The Vortex86MX processor is integrated RDC Display chip which is an ultra low powered graphics chipset with total power consumption at around 1-1.5 W.

LAN

The Vortex86MX processor is integrated 10/100Mbps Ethernet controller that supports both

10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area

Network for full interaction with local servers, wide area networks such as the Internet.

I/O and IRQ settings can be done by software with the supplied utility software, or it can be set for Plug and Play compatibility. The controller supports: Half / Full-Duplex Ethernet function to double channel bandwidth, auto media detection.

AUDIO

The ALC262 series are 4-Channel High Definition Audio Codecs with UAA (Universal Audio

Architecture) featuring two 24-bit stereo DACs and three 20-bit stereo ADCs, they are designed for high performance multimedia desktop and laptop systems. The ALC262 series incorporates proprietary converter technology to achieve over 100dB Signal-to-Noise ratio playback quality; easily meeting PC2001 requirements and also bringing PC sound quality closer to consumer electronic devices.

Operating system support

The PMX-089T provides the VGA and LAN drivers for Linux, Windows CE, Windows XP

Professional, and Windows Embedded standard (XPE). (Linux can use with Compact Flash card only.)

Please get the drivers from DMP official website: www.compactpc.com.tw

.

PMX-089T also supports most of the popular Linux distributions, for more detail information, please visit DMP official website: http://www.dmp.com.tw/tech/vortex86dx/


3.1. PMX-089T Development Note

<Primary /Secondary IDE: Master or Slave>

Micro SD: Primary Master

CF Slot: Secondary IDE: Master or Slave (User can use slide switch (in side of CF slot) to adjust Master or Slave

<Window CE6.0 development guide>

Windows Embedded CE 6.0 BSP, trial CE image and development notes, please visit technical website to get more information: www.compactpc.com.tw

<Linux installation note>

Please forced the IDE setting in BIOS to PIO mode before install Linux on PMX-089T as follows:

1-Go to the advanced BIOS setting and make the “Onboard IDE Operate Mode” is

“Legacy Mode”

2-Go to the PCI/PnP and make the “PCI IDE BusMaster” is “Disable"

< XP professional /Home /Embedded and Windows 2000 installation note >

1-Please visit technical website to get more information: www.compactpc.com.tw

<Enhance CF to run the UDMA2/4>

1-Please select DMP “ICF Card” to supporting UDMA 2/4 Mode.

<How to boot up from the Micro SD card>

1-Get into the BIOS setup Utility

2-Go to the Advanced

3-Choose Primary IDE Pin Select: SD card

4-Press “F10” to save configuration changes and exit setup


3.2. BIOS Default setting

If the system cannot be booted after BIOS changes are made, Please follow below procedures in order to restore the CMOS as default setting.

 Press “End” Key, when the power on

 Press <Del> to enter the AMI BIOS setup

 Press “F9” to Load Optimized Defaults

 Press “F10” to Save configuration changes and exit setup


Warranty

This product is warranted to be in good working order for a period of one year from the date of purchase.

Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return

Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.


DMP Electronics Vortex86MX PMX-089T-8A User`s manual

DM&P Vortex86MX Panel PC with 8.9” TFT LCD

User’s Manual

Copyright

Trademarks Acknowledgment

Safety Information

General Information

1.1 Product Description

1.2 Product Specification

1.3 Inspection standard for TFT-LCD Panel

1.3 Product Dimension

1.4 Ordering Information

1.5 Packing List

System Installation

2.1 CPU Board Outline

2.2 Connector Summary

2.3 Connector Pin Assignments

2.4 External I/O Overview

2.5 External I/O Pin Assignment

2.6 System Mapping

2.7 Watchdog Timer

Driver Installation

3.1. PMX-089T Development Note

3.2. BIOS Default setting

Related manuals

XtendLan

PTDX9211

Icop

PDX-089T-D5A

Icop

PMX-057T-8A-512

Icop

PMX-090T-8A-512

Icop

PMX-090T-8A-512