Samsung JE68-00131B User`s manual

USER’S MANUAL
SRP-770
LABEL PRINTER
JE68-00131B
Rev. 1.05
www.samsungminiprinters.com
1
Safety Precautions
In using the present appliance, please keep the following safety
regulations in order to prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
Do not plug several products in one
multi-outlet.
You must use only the supplied adapter.
It is dangerous to use other adapters.
This can provoke over-heating and a fire.
If the plug is wet or dirty, dry or wipe it
before usage.
If the plug does not fit perfectly with the
outlet, do not plug in.
Be sure to use only standardized
multi-outlets.
WARNING
Violating following instructions can cause slight wound or damage the appliance.
Keep the desiccant out of children’s
reach.
Install the printer on the stable surface.
PROHIBITED
PROHIBITED
Use only approved accessories and do
not try to disassemble, repair or remodel
it for yourself.
Do not use the printer when it is out of
order. This can cause a fire or an
electrocution.
DISASSEMBLING
PROHIBITED
TO UNPLUG
If the printer falls down, it can be broken
and you can hurt yourself.
If not, they may eat it.
ONLY SUPPLIED ADAPTER
PROHIBITED
Do not pull the cable to unplug.
Keep the plastic bag out of children’s reach.
PROHIBITED
PROHIBITED
If not, a child may put the bag on his head.
This can damage the cable, which is the
origin of a fire or a breakdown of the printer.
Do not plug in or unplug with your hands
wet.
If you observe a strange smoke, odor or
noise from the printer, unplug it before
taking following measures.
You can be electrocuted.
Switch off the printer and unplug the set
from the mains.
After the disappearance of the smoke, call
your dealer to repair it.
PROHIBITED
Call your dealer when you need these
services.
Switch off and unplug the printer before
calling your dealer.
PRINER
PRINTER
DEALER
Do not let water or other foreign objects
in the printer.
If this happened, switch off and unplug the
printer before calling your dealer.
Do not bend the cable by force or leave it
under any heavy object.
A damaged cable can cause a fire.
PROHIBITED
TO UNPLUG
2
PRINTER
PRINTER
PROHIBITED
PRINTER
3
Table of Contents
1. Unpacking
& Repacking
Your printer box should include these items. If any items are damaged or missing,
please contact your dealer for assistance.
1. Unpacking & Repacking .........................................................................5
2. Samsung Label Printer ...................................................................6
Note : Please keep the packing materials(①,②,④,⑥) for future repacking to send
a printer for repairs.
⑨ Label
(Paper)
⑧ Operator’s Manual & CD
3. Connecting the Power Supply ......................................................7
4. Connecting the Interface Cable ..................................................8
⑥ Cushion
(TOP)
⑦ Power Cord
5. Installing or Replacing the Paper Roll ......................................9
6. Setting the Dip Switches .............................................................10
7. The Self Test .....................................................................................11
③ Power Supply
⑤ Printer (SRP-770)
8. The Peel-off ......................................................................................12
9. Using Fan Fold Paper.....................................................................13
② Cushion
(Bottom)
10. Auto Cutter (Option) ...................................................................14
11. Cleaning Head ...............................................................................15
12. Install and Uninstall Windows Driver ...........................................16
④ Pe-bag
① Printer Box
※ You can repack the printer package in above numeric order(①~⑨)
4
5
2. Samsung Label Printer
3. Connecting the Power Supply
CAUTIONS:
Status Indicator
Feed Button
Cover Peel-off
Power Switch
Cover Open/Close
When connecting or disconnecting the power supply from the printer, make sure that
the power supply is not plugged into an electrical outlet. And the power supply’s
rated voltage and your outlet’s voltage do not match, contact your dealer for
assistance. Then do not plug in the power cord. Otherwise, you may damage the
power supply or the printer.
1. Make sure that the printer’s power switch is turned off, and the power supply’s
power cord is unplugged from the electrical outlet.
2. Check the label on the power supply to make sure that the voltage required by the
power supply matches that of your electrical outlet.
Printer Head
(Option)
3. Plug in the power supply’s cable as shown below. Notice that the flat side of the
plug faces down.
Paper Holder
Paper Guide
Auto Cutter
Paper(gap) Sensor
Peel-off Sensor
Paper Adjuster
Power Connector
Dip Switch
Interface Connectors
[RS-232C, IEEE1284, USB]
6
7
4. Connecting the Interface Cable
5. Installing or Replacing the Paper Roll
① Open Cover
② Open Guides
③ Install Roll
Universal Serial Bus
(USB)
Parallel Interface
Serial Interface
RS-232 default
setting is 19200 baud,
no parity, 8 data bits
and 1 stop bit
④ Close Guides to the Width of the paper
8
⑤ Close Cover
9
6. Setting The Dip Switches
7. The Self Test
6-1. Setting the Dip Switches
The self-test checks whether the printer has any problems. (You cannot perform this
procedure if using the printer’s label peel-off option) If the printer does not function
properly, contact your dealer. The self-test checks the following;
The Dip Switches are located on the bottom of the printer. The Dip Switches are used to
set the Printer to perform various functions. Follow these steps when changing Dip
Switches setting :
1. Turn the printer power switch off.
2. Remove the screw on the bottom
of the printer and open the bracket.
3. Flip the Dip Switches using tweezers
or another narrow-ended tool.
Switches are off when up and on
when down in the Figure below.
4. The new setting takes effect
when you turn on the printer.
1.
Make sure that paper roll has been installed properly.
2.
Turn on the power while holding(2sec) down the FEED button. The self-test begins.
3.
The self-test prints the current printer status, which provides the control ROM version
and the DIP switch setting.
Note : Always change Dip Switch settings
only when the printer is turned off.
6-2. Functions of Dip Switches
6-2-1. Dip S/W 1
No Functions
1,2
Speed
Selection
3,4
Density
Selection
5
6
Exhibition
Selection
Media
Selection
7
Auto Cutter
8
Position
Selection
With
AutoCutter
Details
2
Off
Off
On
On
4
Off
Off
On
On
Off
On
Off
On
Off
On
Off
On
Off
On
6-2-2. Dip S/W 2
No
Functions
1
Speed
Off
2.5 ips
On
3.0 ips
Off
4.0 ips
On
5.0 ips
3
Density
Off
0(Low)
On
7
Off
13
On
20(High)
Normal mode
Demo mode
Label Paper
Normal Paper
Without Auto Cuter
With Auto Cutter
Move to Cutting Position
Move to top of next page
Back Feeding printing
Continuous printing
10
1,2
Baud
Rate
3
Media
Detection
4
Memory
Selection for
Image Store
5
Emulation
6~8
Developer
Mode
2
Off
Off
On
On
Off
On
Off
1
Off
On
Off
On
Details
Baud Rate
9,600 bps
19,200 bps
57,600 bps
115,200 bps
Detect Gap only
Detect Gap and
Black-mark
SRAM
On
Flash Rom
Off
On
SAMSUNG command
Emulation
Default --- off
11
8. The Peel-off
9. Using Fan Fold Paper
Printers can Peel-off a single label.
You must remove the label before the printer prints the next label.
Insert paper through both the rear slot and guides.
Adjust holders and guides to the width of the paper.
① Open the peel-off cover and turn on peeler switch.
Open the Dust Cover
and Insert paper
Dust Cover
Adjust holders papers and paper Fixed
② Remove the one a paper and
insert the paper through slot.
Adjust Guides
③ Adjust the paper guides and close the cover.
remove
Paper Fixed
12
13
10. Auto Cutter (Option)
11. Cleaning Head
Auto cutter should be used for continuous paper only. ( i.e. roll paper)
Paper dust on the heating elements may lower the printer quality. In this case, clean the
print head as follows :
1. Open the Dip switch cover, and make the switch 1 number 7 “On”.
(Refer to printer mode setting at Chapter 6.)
2. Put a paper roll into the printer and close the cover.
Cautions 1. Turn Off the printer power before cleaning.
2. Note that the thermal head becomes very hot during normal operation,
creating the danger of burn injury. Be sure to wait for about 2~3 minutes
after turning printer power off before beginning the cleaning.
1. Open the printer cover.
2. Clean the thermal element (the area which is marked a thin black line) of the thermal
head with a cotton swab moistened with a alcohol solvent (ethanol, methanol, or IPA).
3. After confirming that the alcohol solvent has been dried up completely, close the
cover-open.
Note 1. Never touch the thermal element with your hand,
then the thermal element can be damaged.
2. Don’t scratch the printer head.
Caution (Partial cut)
: Once the printer cut the paper, remove the receipt in order for next printing.
Otherwise the receipt could be back into the printer and the cutter would
cut it again.
䧎 Clean it up when you replace every roll of paper to prevent the quality
deterioration.
14
15
12. Install and Uninstall Windows Driver
(3) Click “Install” Button.
12.1 Download install-program from Website
(1) Execute web-browser.(Ex: Internet Explorer)
(2) Type http://www.samsungminiprinters.com
(3) Connect website.
(4) In “Quick menu”, click download button.
(5) Download “SRP-770_V3.X.X.exe” in SRP-770 section.
12.2 Install Windows Driver
12.2.1 Serial Parallel interface
(1) Double click “SRP-770_V3.X.X.exe” file.
(2) Click “Next” Button.
(4) Select operating system type.
16
17
(5) Select interface (port) type.
12.2.2 USB interface
A. Windows 95/98/ME
(1) Double click “SRP-770_V3.X.X.exe” file.
(2) Click “Next” Button.
(6) Please reboot computer.
18
19
(3) Click “Install” Button.
(4)
Select operating system type.
20
(5)
Select “USB” interface (port) type.
(6)
Please turn-off printer and turn-on printer.
(7)
When “Add new hardware wizard” for install “USB print support” driver pops up,
click “Next” button.
21
(8)
Please click “Next” button three times.
(9)
When “USB print support” driver is installed, your system automatically restart
after 10 seconds.
(10)
(3)
Click “Install” Button.
(4)
Select operating system type.
After the system restart, please turn-on printer.
B. Windows NT/2000
(1)
Double click “SRP-770_V3.X.X.exe” file.
(2)
Click “Next” Button.
22
23
(5)
(6)
Select “USB” interface (port) type.
C. Windows XP/2003 Server
(1)
Double click “SRP-770_V3.X.X.exe” file.
(2)
Click “Next” Button.
(3)
Click “Install” Button.
Please turn-off printer and turn-on printer.
* If you can see this dialog, don’t worry comment in dialog.
Printer and driver work well. Please click “Yes” button.
24
25
(4)
* If you can see this dialog, don’t worry comment in dialog.
Printer and driver work well. Please click “Continue Anyway” button.
Select operating system type.
(7)
(5)
Select “USB” interface (port) type.
(6)
Please turn-off printer and turn-on printer.
26
If “Add new hardware wizard” for install “SAMSUNGSRP-770” driver pops up,
click “Next” button.
27
(8) Please click “Next” button until you can see “Finish” button.
(9)
Please click “Finish” button.
12.3 Uninstall Windows Driver
(1) Click on the Start button, and then click on Settings > Control Panel.
(2) Double click “Add/Remove Programs” icon.
(3) Select “SAMSUNG SRP-770 LABEL Windows Driver 3.X.X”.
(4) Click “Change/Remove” button.
*If you can see this dialog, don’t worry comment in dialog.
Printer and driver work well. Please click “Continue Anyway” button.
28
29
(5)
Select printer to remove.
(6)
Click “Uninstall” Button.
(7)
Please reboot computer.
12.4 Printer Settings
1) Measurement: Select measurement of “Top Margin”. (Inch or millimeters)
2) Top Margin: top margin value of paper
3) Density: Select density of printing quality. (0 ~ 20)
4) Media Type: Select paper media type. (“Black Mark” is under development)
5) Orientation: Set printing direction.
6) Speed: Set printing speed. (2.5 ~ 3.0)
30
31
7) Customer Paper Size
【 Specification 】
Printing method
Thermal line printing
Dot density
203 dpi (8 dot/mm)
Printing width
25.4 ~ 101.6 mm
Paper width
38.1 ~ 104 mm
Printing speed
127 mm/sec
Receive Buffer Size
4K Byte
※ Note : Printing speed may be slower, depending on the data transmission speed
and the combination of control commands.
Input voltage
100~240V AC
Supply voltage
Frequency
50/60 Hz
Output voltage
DC 24V
5 ~ 45 ℃ (Operating)
Temperature
-25 ~ 70 ℃ (Storage)
Environmental
30 ~ 80 % RH (Operating)
conditions
Humidity
10 ~ 90 % RH (Storage)
; Except for paper
10,000,000 lines
LIFE
Mechanism Head
5×107 pulse (50km)
MCBF
Mechanism
20,000,000 lines
a)
Add Customized Form: Create new customized form. Customer must type
“Form Name”, “Width” and “Length”. Width and Length in customized form
must be the number in the range from Minimum to Maximum size.
b)
Delete Customized Form: You can delete customized form but default form
may not be deleted.
This marking shown on the product or its literature, indicates that is should not
be disposed with other household wastes at the end of its working life, To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take this item for environmentally safe
recycling. Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial wastes
for disposal.
※ All specifications are subjected to change without notice.
Exit Program: Exit utility program.
32
33