Mitsubishi SL25U User manual

ENGLISH
MODEL XL30U/XL25U/SL25U
EN – 1
ESPAÑOL
XL30
XL25
SL25
ITALIANO
DEUTSCH
FRANÇAIS
LCD
Projector
User Manual
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interference with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class B device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
When using the projector in Europe
COMPLIANCE NOTICE
This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC “EMC
Directive” as amended by Directive 93/68/EEC and
73/23/EEC “Low Voltage Directive” as amended by
Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B. Use the shielded DSUB/5 BNC cable with this equipment so as to keep
interference within the limits of a EN55022 Class B.
Please follow WARNINGS instructions.
EN – 2
ENGLISH
Contents
Important safeguards ...........................................................................4
Overview ............................................................................................... 6
Using the remote control ......................................................................8
Battery installation ......................................................................................................... 8
Installation ............................................................................................9
Basic connections ............................................................................... 10
Projector + AV equipment ............................................................................................. 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + personal computer ...................................................................................... 11
Preparing the projector for operation ...............................................
To operate projector power ON..........................................................
Menu operation ..................................................................................
Picture adjustment .............................................................................
Advanced feature for presentation ....................................................
12
13
15
18
20
Expand ........................................................................................................................... 20
PinP (Picture in Picture) ............................................................................................... 20
Still ................................................................................................................................. 20
Mouse remote control .................................................................................................... 21
Lamp replacement .............................................................................
Maintenance .......................................................................................
Troubleshooting ..................................................................................
Indicators ............................................................................................
Specifications ......................................................................................
22
23
24
25
26
Kensington Lock ............................................................................................................ 26
Connectors ..................................................................................................................... 27
Dimensional drawings .................................................................................................. 27
What’s included in the box ............................................................................................ 27
Replacement part .......................................................................................................... 27
Specification of RGB signals in each computer mode of the projector ....................... 28
Trademark, Registered trademark
Windows 98 and Windows 95 are registered trademarks of Microsoft in the U.S. and other countries.
Macintosh is registered trademark of Apple Computer Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines Corporation.
MicroSaver and Kensington are registered trademarks of Kensington Technology Group.
Other brand or product names are trademarks or registered trademarks of their respective holders.
C
EN – 3
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD projector.
1.
Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2.
Retain instructions
The safety and operating instructions should be
retained for future reference.
3.
Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
4.
Instructions
All operating instructions must be followed.
5.
Cleaning
Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
6.
Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, electric shock or other personal injury.
7.
Water and moisture
Do not use this projector near water or in contact with water.
8.
Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the
projector. Any mounting of the appliance should
follow the manufacturer's instructions and
should use a mounting accessory recommended
by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9.
Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturer's instructions have been adhered to.
EN – 4
10.
Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11.
Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles,
and points where they exit from the appliance. Do
not put the power cord under a carpet.
12.
Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13.
Objects and liquids
Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the projector.
14.
Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified service personnel.
15.
Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
(a)
If the power-supply cord or plug is damaged.
(b)
If liquid has been spilled, or objects have
fallen into the projector.
(c)
If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.
(d)
If the projector has been exposed to rain
or water.
(e)
If the projector has been dropped or the
cabinet has been damaged.
(f)
If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16.
Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17.
Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owner's
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is
operating.
It may hurt your eyes.Never let children look into
the lens when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning main power off.
Do not touch Air outlet grille and Bottom
plate which becomes hot.
Do not touch them or put other equipment in front of
Air outlet grille. The heated Air outlet grille and Bottom plate may cause injury or damage to other equipment. Also, do not set the projector on the desk which
is easily affected by heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventilation slots become clogged with dirt or dust, the temperature inside of the projector may rise and cause
some troubles, such as damage of inside parts, and
shortening the life of panel.
Do not look into the air outlet grille when
projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the projector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free surface: otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious injury and damage to the projector.
• Slanting the projector more than ±15˚(right and left
or front and rear) may cause trouble or explosion of
the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and ventilation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN – 5
ENGLISH
WARNING:
Overview
1 2
34
10
9
5
6
8
1
2
3
4
5
6
Remote control sensor (Front)
Air outlet grille
Zoom
Focus
Control panel
Kensington Security Lock Standard
connector
7 Easy-carry handle
8 Foot adjustment buttons (Left/Right)
9 Lens
10 Air outlet grille
7
Control panel
1
14
2
13
3
12
4
11
5
6
10
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
LAMP indicator
TEMP (temperature) indicator
AUTO POSITION button
ENTER button
MENU button
COMPUTER button
VOLUME (+, –) buttons
KEYSTONE (+, –) buttons
RIS sensor
VIDEO button
Direction buttons
MUTE button (Audio/Video)
POWER button
POWER indicator
8
9
Rear panel
1
2 3 45 6
7
8
9
10
11
1
2
3
4
5
6
Remote control sensor (Rear)
USB terminal
RS-232C (DIN 8P) terminal
Reset button
Wired remote control (REMOTE) jack
COMPUTER / COMPONENT VIDEO IN 1
terminal (D-SUB mini 15P)
7 COMPUTER AUDIO IN jack
8 MONITOR OUT terminal (D-SUB mini 15P)
9 AUDIO OUT jack
10 Main power
I : ON
O : OFF
11
12
13
14
16
EN – 6
15
14
13 12
Air inlet grille
Power jack
Ground terminal
COMPUTER / COMPONENT VIDEO IN 2
terminal ( R/PR, G/Y, B/PB, H/HV, V )(BNC)
15 Video/audio input terminals
16 Speaker
ENGLISH
Bottom side
1
1
2
3
2
Caution:
Do not replace the lamp immediately after using the
projector because the lamp has got extremely hot.
Adjustment foot (Left/Right)
Lamp cover
Air inlet grille/Filter cover
3
Remote control
1
3
2
4
5
6
7
8
COMPUTER
2
1
VIDEO
KEYSTONE
EXPAND
1
2
P in P
AUTO POSITION
VOLUME
–
LASER
+
9
24
23
22
21
20
19
10
11
12
MENU
R-CLICK
ENTER
MUTE
STILL
16 : 9
18
17
16
13
MEMORY
SELECT
DVD
15
VIDEO
14
25
1 Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 POWER button
6 KEYSTONE button
7 EXPAND button
8 + , – (VOLUME) buttons
9 Mouse pointer
10 MENU button
11 STILL button
12 MUTE button (Audio/Video)
13 Programmable buttons
14 SELECT switch
15 MEMORY button
16 16 : 9 button
17 ENTER button
18 R-CLICK button (For mouse)
19 Direction buttons
20 LASER button
21 AUTO POSITION button
22 PinP button
23 VIDEO 1, 2 button
24 COMPUTER 1, 2 button
25 Left click button (For mouse)
• The + and - buttons are used in the KEYSTONE
adjustment and the EXPAND mode in addition to the
volume control.
• Pressing the LASER button emits a laser beam. Even
when you keep holding down the LASER button, it is
emitted only one minute. To keep emitting it longer,
press the LASER button again.
• You can disable the LASER button to prevent
laser radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the }
button three times.
• To enable the LASER button, while holding the LASER
button down, press the { button three times.
About the laser beam
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH: 640-660nm
MAX OUTPUT : 1mW
CLASS 2 LASER PRODUCT
Complies with 21 CFR, 1040.10 AND 1040.11
IEC 60825-1:1993+A1:1997
This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength
: 640-660 nm)
Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)
CAUTION :
• Pressing the LASER button on the remote control emits a laser beam. Do not
look into the laser beam directly. Do not point the laser beam at anyone.
Looking at the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specified herein may
result in hazardous radiation exposure.
EN – 7
Using the remote control
Battery installation
Use two AA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
3. Replace the back cover.
1
2
3
Important:
• Do not use a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area (for wireless control system)
The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 7 m (about 23 feet). Depending on the type of the
screen, the distance will be different.
30˚
20˚
20˚
5˚
5˚
30˚
20˚
20˚
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
(6.5") between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
• When the remote control is connected with remote
control cable, it does not work as a wireless
remote control.
• When you need a longer cable, use a pin-pin cable.
• When using the wired remote control, the laser beam may be darker. It is normal.
EN – 8
Installation
Height
Picture size can be set by changing the distance between the screen and the projector.
Front projection
To find the approximate distance
Width
between the projector and screen:
Screen
A
B
Multiply the width of the screen
x
1.8 (min.) , Multiply the width of
Screen
the screen x 2.3 (max.).
• Refer to the chart for recomA=B
mended distances in maximum
zoom and minimum zoom.
(between the screen and
H
L
the head of the projector)
Screen
Diagonal size
(inch)
40 "
60 "
80 "
100 "
150 "
200 "
250 "
300 "
(cm)
102
152
203
254
381
508
635
762
Width
(inch)
32 "
48 "
64 "
80 "
120 "
160 "
200 "
240 "
(cm)
81
122
163
203
305
406
508
610
Height
(inch)
24 "
36 "
48 "
60 "
90 "
120 "
150 "
180 "
(cm)
61
91
122
152
229
305
381
457
Distance from screen (L) / (approximate)
Maximum
Minimum
zoom (WIDE)
zoom (TELE)
(inch)
(m)
(inch)
(m)
55 "
1.4
71 "
1.8
84 "
2.1
107 "
2.7
114 "
2.9
144 "
3.7
143 "
3.6
181 "
4.6
215 "
5.5
272 "
6.9
288 "
7.3
364 "
9.3
9.2
361 "
–
–
434 "
11.0
–
–
Height projected
image (H)
(inch)
1.2 "
1.8 "
2.4 "
3.0"
4.5 "
6.0 "
7.5 "
9.0 "
(cm)
3.0
4.6
6.1
7.6
11.4
15.2
19.1
22.9
• The above numbers are approximate, and may be slightly different from the actual measurements.
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
• This warranty does not cover damage caused by
the use of any unrecommended ceiling mount kit
and the installation of the ceiling mount kit at an
improper location.
SCREEN
• When using the ceiling mount, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See Page 16.
• Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
Rear projection
Ask a specialist for installation. For more details,
consult your dealer.
• For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to MIRROR. See Page 16.
Caution:
• Placing the projector on a carpet reduces ventilation from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
• Place the projector more than 50 cm (20 in.) from
the wall to prevent blocking the intake, exhaust
slots and ventilation of this projector because hot
air comes out of it.
• Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
• in a dusty or humid place
• while the projector is lying sideways or upside
down
• near a heater
• in a kitchen or oily, smoky or damp place
• in direct sunlight
• with high temperature, such as a closed car
• where the temperature is lower than 41°F
(+5˚C) or higher than 95°F (35˚C).
Important:
• Do not put stress on the lens, as this may cause
damage.
SCREEN
EN – 9
ENGLISH
Orientation of the projector
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal
computer that have analog RGB output connectors.
Important:
• Make sure that the connected device is turned off before starting connection.
• Plug in the projector and the connected devices firmly, and unplug them by holding and pulling out their
power plugs, not by pulling the power cords.
• When the projector and the connected devices are located too close to each other, the projected image may be
affected by their interference.
• See the owner’s guide of each device for details about their connections.
Projector + AV device
Important:
• Connect the video and audio plugs of the AV cable to the proper terminals matching their colors respectively.
• The S-video signal takes priority over the video signal. When you input both the S-video signal and the
normal video signal at the same time, the normal video signal is ignored.
• When the connected AV device uses a BNC connector for its video output, connect it to the VIDEO IN2 (BNC)
terminal. When both the VIDEO IN2 (BNC) terminal and the VIDEO IN2 (RCA) terminal are engaged at the
same time, the image supplied to the VIDEO IN2 (RCA) terminal takes priority.
VCR, etc.
To audio output
Connect either
one of these.
To audio input
To video output
To video input
To S-video output
To S-video input
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such a DVD player
with this projector, use the COMPUTER/COMPONENT VIDEO 2 IN terminal.
DVD player or HDTV decoder
AUDIO cable
CB(PB) Y CR(PR)
To COMPUTER
AUDIO IN
to AUDIO OUT
BNC - RCA connector
(option)
B
G
R
BNC-BNC cable (option)
R/P R
G/Y
B/P B
•
•
•
•
•
The terminals’ names Y, PB, and PR are examples of a case where a HDTV decoder is connected.
The terminals’ names are different depending on the connected devices.
Use BNC-BNC cables for connection.
The image may not be projected correctly with some DVD players.
When connecting a HDTV decoder having RGB output terminals, set the COMPUTER INPUT to RGB in the
SIGNAL menu.
EN – 10
ENGLISH
Projector + Computer
For the computer with a Mini D-SUB 15P connectors
RGB cable for PC
To COMPUTER AUDIO IN
To PC audio
output
To monitor port
Computer
To COMPUTER IN
(Mini D-SUB 15P)
AUDIO OUT
MONITOR OUTPUT
To MONITOR OUT
RGB cable for PC (option)
When outputting to both the compute's monitor and the projector.
For using the COMPUTER/COMPONENT VIDEO IN 2 (BNC) terminals
to COMPUTER AUDIO IN
computer
R/P R
to PC audio
output
G/Y
B/P B
H/HV
MONITOR OUTPUT
V
AUDIO OUT
to monitor
port
Mini D-SUB 15pin-BNC
conversion cable (optional)
Important:
• When you use a longer RGB cable instead of the provided cable, the picture quality may deteriorate.
• Some computers may require additional connectors or analog RGB output adapters to be connected with this
projector. Contact your dealer for further information.
• This projector uses a stereo pin jack for its audio input. Check the type of the audio output terminal of the
connected computer and prepare a proper cable for connection. Some computers may not have the audio
output terminal.
For Macintosh
• If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further
information.
• Some Macintoshes may require a MAC adapter for the RGB cable for connection with this projector. Contact
your dealer for further information.
About DDC™
The COMPUTER/COMPONENT VIDEO IN 1 terminal of this projector complies with the DDC1/2B standard.
When a computer supporting this standard is connected to this terminal, the computer will automatically load
the information from this projector and prepare for output of appropriate images.
• After connecting a computer supporting this standard to this terminal, turn on the projector’s main power
switch first, and then boot up the computer.
• You may need to install the DDC driver, depending on the computer you use. In this case, you need to
download the driver from our Web site. Contact your dealer or Mitsubishi sales office for further information.
EN – 11
Preparing the projector for operation
Getting ready for projection
1. Attach the provided power cord to the projector.
2. Plug the power cord in the wall outlet.
3. Remove the lens cap.
Warning:
• Do not look into the lens directly when the
projector is “ON.”
• The lens cap is for protecting the lens. If you leave
the lens cap on the lens with the projector turned
on, it may be deformed. Remove the lens cap when
you turn on the projector.
• The power cords for use in the U.S. and Europe
are included with this projector. Use the
appropriate one for your country.
• This projector uses the power plug of three-pin
grounding type. Do not take away the grounding
pin from the power plug. If the power plug doesn’t
fit your wall outlet, ask an electrician to change
the wall outlet.
• The provided power cord for the U.S. is rated at
120 V. Never connect this cord to any outlet or
power supply using other voltages or frequencies
than rated. If you use a power supply using other
voltage than rated, prepare an appropriate power
cord separately.
• Use 100-240 V AC 50/60 Hz to prevent fire or
electric shock.
• Do not place any objects on the power cord and
keep the projector away from heat sources to
prevent damage to the power cord. If the power
cord gets damaged, contact your dealer for
replacement because it may cause fire or electric
shock.
• Do not modify or alter the power cord. If the
power cord is modified or altered, it may cause fire
or electric shock.
Caution:
• Plug in the power cord firmly, and unplug it by
holding and pulling out the power plug, not by
pulling the power cord.
• Do not plug in or out the power cord with your
hand wet. It may cause electric shock.
Adjusting the angle of projection
For the best projection, project the image on a flat
screen installed at 90 degrees to the floor. If
necessary, tilt the projector using the two adjustment
feet on the bottom of the projector.
screen
EN – 12
Adjustment foot
1. Tilt up the project to the appropriate angle.
2. Press the foot adjustment buttons next to the
adjustment feet, and the adjustment feet will
come out.
3. Release the buttons to lock the adjustment feet to
that position.
4. Rotate the adjustment feet for fine adjustment.
Foot adjustment
buttons
Adjustment foot
After using the projector
5. Put the adjustment feet back into the projector by
pressing the foot adjustment buttons.
• Install the screen on a flat wall at 90 degrees to
the floor.
• Position the projector so that it projects an image
filling the screen as illustrated on page 9.
• Keep an appropriate distance from the projector to
the screen according to the screen size chart on
page 9.
• The image becomes trapezoid shape when the
screen or project is not level. Use KEYSTONE
button and + or - buttons on the remote control or
KEYSTONE + or - buttons on the control panel to
adjust, however, the circumference of the image
may not be focused.
Important:
• Slanting the projector more than ±15˚(right and left
or front and rear) may cause trouble or explosion of
the lamp. You can tilt the projector up to 7 degrees
using the adjustment feet only.
• The image may not be projected in a shape of a
regular rectangle or with its aspect ratio of 4:3,
depending on the installation conditions of the
projector and the screen.
• When the keystone adjustment is carried out, the
adjustment value is indicated. Note that this
value doesn’t mean a projection angle.
• The allowable range of the adjustment value in
the keystone adjustment will vary depending on
the installation conditions.
ENGLISH
To operate projector power ON
2, 9
3, 7, 8
3, 7, 8
MUTE button
COMPUTER
VIDEO
EXPAND
1
2
P in P
AUTO POSITION
VOLUME
AUTO POSITION
button
2
1
KEYSTONE
LASER
–
+
MENU
R-CLICK
ENTER
MUTE
STILL
16 : 9
4
AUTO POSITION
button
4
MUTE button
MEMORY
SELECT
DVD
1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER button. The light source lamp starts warming up, eventually turning completely on.
• When the light source lamp does not light up,
wait until the LAMP indicator is turned off, then
press the POWER button again.
• If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the indicator lamp will blink for
one minute.
condition
indicator
stand-by
when light source lamp is on
light source lamp held off temporarily
LAMP POWER
green
-
red
green
red
Important:
• A darkened image may be seen right after pressing
the POWER button due to warming up of this projector. While warming up, no other commands can
be accepted.
• After the power is turned on or the LAMP MODE is
changed, the screen may flicker before the lamp operation becomes stable. This is due to the characteristics of the lamp, not a failure of the lamp.
• When the lamp indicator is blinking red, the service life of the lamp is about to end. Replace the
lamp. See pages 22 and 25.
VIDEO
• The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4. Select the desired external input source by using
the COMPUTER 1,2 or VIDEO1,2 button on the remote control or the COMPUTER or VIDEO button
on the control panel.
• Pressing the VIDEO button on the control panel repeatedly will select VIDEO IN 1 and VIDEO IN 2.
• Pressing the COMPUTER button on the control panel
repeatedly will select COMPUTER IN 1 and COMPUTER IN 2.
• The projector automatically selects the appropriate
signal format. The selected signal format is displayed on the screen.
• The COMPUTER or VIDEO buttons do not work
when MENU is displayed. At this time, the prohibition mark ( ) appeares on the screen.
• When selecting the COMPUTER input, the image
may flicker. Press the $ or % button to adjust the
image.
• The intensity of the lamp will be STANDARD for 2
minutes regardless of the setting of the LAMP
MODE when the lamp turns on.
5. Adjust the image size with the zoom ring by turning it.
6. Adjust the focus with the focus ring by turning it.
zoom ring
wide
tele
focus ring
near
far
EN – 13
To operate projector power ON (Continue)
Turning off the projector
7. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
• To exit this mode, press any button except the POWER
button. (Some buttons on the remote control don’t
work for exit from this mode.)
8. Press the POWER button again.
The light source lamp will go out. Though the light source
lamp will go out at this second press of the POWER button, the exhaust fan continues to operate for another 120
seconds to cool down the lamp and LCD panel. In this
case, the lamp indicator will go out.
9. Turn off the main power switch, and the POWER indicator will go out.
• In cases where the main power switch is accidentally
turned off when either the intake/exhaust fan or the
power source lamp is in operation, allow the unit to
cool down for 10 minutes with the power turned off.
Repeat step 3 when turning on the power source lamp.
If the lamp does not turn on immediately, repeat this
step two or three times. Replace the lamp if it should
still fail to turn on.
AUTO POSITION button
When the image isn’t projected in the right position with
COMPUTER selected as the image source, follow the
steps below.
1. Project a bright image such as the “Trash” window on
the full screen.
2. When the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
• If the image is still not in the right position, adjust the
image position using the SIGNAL menu.
Volume from the speaker
Press the volume + or – buttonto change the volume from
the speaker.
The volume control bar will appear on the screen.
AUDIO
15
• The volume control bar will disappear about 4 seconds
after releasing the volume buttons.
• The volume buttons don’t work while the MENU
selection bar or the MENU is being displayed.
• When a high-level audio signal, such as a DVD audio
signal, is supplied to the COMPUTER AUDIO IN
terminal, the output from the speaker may be distorted.
AV mute
The image and audio signals are temporarily muted by
pressing the MUTE button. To bring them back to their
normal level, press the MUTE button again.
• The audio from the AUDIO OUT jack is also muted by
pressing the MUTE button.
• If the MUTE MODE in the INSTALLATION menu is
set to LOGO, the splash screen will appear by pressing
the MUTE button.
Please contact your dealer or Mitsubishi sales office for
further information.
• You can alter the splash screen freely. Please contact
your dealer or Mitsubishi sales office for further
information.
• The lamp mode becomes “LOW” during muting.
Therefore, the display of LOGO will darken, which
isn’t a failure.
EN – 14
• Muting will be cancelled in 3 hours automatically for
the purpose of protecting devices. However, when the
mute mode has been set to “LOGO,” muting won’t be
cancelled.
ANAMORPHIC mode
When playing DVD discs containing data of letterboxed
image, press the 16:9 button. Exit the ANAMORPHIC
mode, by pressing the 16:9 button again.
Caution:
• When you have finished using this projector, wait 120
seconds for the exhaust fans to stop. Then turn off the
main switch and unplug the power cord from the wall
outlet, for safety purposes.
• The lamp cannot be turned on again for 60 seconds after
it was turned off for precautionary purposes. It will take
another 60 seconds before the lamp indicator goes off. If
you want to turn on the projector again, wait until the
indicator is off, and then press the POWER button.
• The exhaust fan rotates faster as the temperature around
the projector rises.
• When the temperature around the projector rises too
high, the sign “TEMPERATURE!!” blinks red on the
screen. If the temperature stays too high, the lamp will
be go out automatically.
Installation other device’s remote commands
You can install other device’s remote commands in the
remote control of this projector.
How to install
1. Set the SELECT switch of the remote control of this
projector to DVD or VIDEO, depending on the device
you use.
2. Place the remote control of this projector and that of
the other device with their transmission windows 2-5
cm apart.
3. Press the MEMORY button.
• The MEMORY button will blink red.
• To cancel the installation, press the MEMORY
button again.
4. Press any programmable button on the remote control
of this projector.
• The MEMORY button will stop blinking and stay
on.
• When no button is pressed for 6 seconds after step
3 and 4, the MEMORY button will go out
automatically.
• See page 8 for the programmable buttons.
5. Hold down the button on the other device’s remote
control whose command you want to install until the
MEMORY button start blinking.
• When the MEMORY button blinks six times and
then goes out, the function has been installed
successfully.
• When the MEMORY button doesn’t blink before
going out, the installation has failed.
• To continue to install other functions, repeat step 3
to 5.
• Some special commands are not memorized,
depending on the type of the remote control.
• Do not install any remote commands of other devices
including air conditioners than video devices.
How to use the installed functions
1. Set the SELECT switch of the remote control of this
projector to DVD or VIDEO, depending on the device
you use.
2. Press the programmable button in which the desired
remote command has been installed.
Menu operation
CONTRAST
BRIGHTNESS
sRGB
COLOR MATRIX *1
COLOR TEMP. *1
COLOR
*2
TINT
SHARPNESS
GAMMA MODE
INSTALLATION
RIS
AUTO POWER ON
AUTO POWER OFF
SPLASH SCREEN
BACK COLOR
MUTE MODE
LAMP MODE
IMAGE REVERSE
RED
± 30
± 30
YELLOW
± 30
± 30
GREEN
± 30
ON , OFF
CYAN
± 30
VIDEO
BLUE
± 30
COMPUTER
MAGENTA
± 30
USER
SATURATION
±5
OFF
RGB-TINT
± 15
STANDARD
CONTRAST R
± 30
HIGH
CONTRAST B
± 30
LOW
BRIGHTNESS R
± 30
USER
BRIGHTNESS B
± 30
± 10
(Displays only when the source is selected to VIDEO)
± 10
(Displays only when the source is selected to VIDEO)
± 10
AUTO, DYNAMIC, STANDARD, THEATER
1, 2, 3, OFF
ON , OFF
OFF, 5, 10, 15, 30, 60 min
ON , OFF
BLUE, LOGO, BLACK
BLACK, LOGO
STANDARD, LOW
OFF, MIRROR, INVERT, MIRROR INVERT
FEATURE
MENU POSITION
EXPAND MODE
FRAME POSI.
VIDEO SIGNAL
SCART INPUT *3
ANAMORPHIC
3D CineView *4
LANGUAGE
RESET ALL
1 (Upper left), 2(Lower right)
(The item can not be selected when
the source is selected to COMPUTER)
1-4
1-5
AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
ON , OFF
OFF, CENTER, UPPER, LOWER
ON , OFF
, English, Español, Deutsch, Français, Italiano,
,
,
,
OK
SIGNAL
MEMORY CALL
HORIZ.POSITION
VERT.POSITION
FINE SYNC. *3
TRACKING *3
COMPUTER INPUT *3
*3
HOLD
AUTO, USER1, USER2
0 - 999
*5
0 - 999
*5
0 - 39
0 - 9999
*5
RGB, YCBCR / YPBPR
AUTO
ON
OFF
USER
MEMORIZE
DELETE
DEFAULT
USER1, USER2
USER1, USER2
* 1: The item can not be selected when the sRGB is set to ON.
* 2: The item can not be selected with certain signals.
* 3: The item can not be selected when the selected source
is VIDEO or S-VIDEO.
* 4: The item can be selected only when the selected source
is VIDEO or S-VIDEO or the inputted signal is TV50 or TV60.
* 5: Setting range is different with certain signals.
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1. Press the MENU button.
opt.
XGA60
IMAGE
2. Press the $ or % button to select the INSTALLATION menu.
opt.
XGA60
INSTALLATION
3. Press the ENTER button (or } button).
opt.
XGA60
INSTALLATION
RIS
AUTO POWER
ON
AUTO POWER
OFF
ON
SPLASH SCREEN
OFF
OFF
ENGLISH
IMAGE
BEGIN
END
CLAMP POSITION *3
CLAMP WIDTH *3
HORIZ. PIXELS *3
VERT LINES *3
VERT. SYNC.
SHUTTER(U)
SHUTTER(L)
SHUTTER(LS)
SHUTTER(RS)
-1 - -99
1 - 99
0 - +63
*5
1 - 63
*5
0 - 9999
*5
0 - 9999
*5
AUTO, ON, OFF
():For SL25U
0 - 383 (299)
():For SL25U
0 - 383 (299)
():For SL25U
0 - 510 (398)
():For SL25U
0 - 510 (398)
4. Press the { or } button to select AUTO POWER
OFF.
AUTO POWER
ON
AUTO POWER
OFF
OFF
OFF
5. Press the $ or % button to adjust auto power off
time.
AUTO POWER
ON
AUTO POWER
OFF
OFF
30 min
6. Exit the menu system by pressing the MENU button several times.
• If the menu operation is not working, press the
RESET button on the terminal board using a suitable sharp object, push gently.
• The settings with
mark, you should press the
ENTER button after selecting.
OFF
ON
EN – 15
Menu operation (continued)
1 IMAGE
CONTRAST ......... Adjusts the picture contrast. The contrast becomes higher as the
opt.
XGA60
number increases.
BRIGHTNESS ..... Adjusts the image brightness. The image becomes brighter as IMAGE
the number increases.
CONTRAST
0
sRGB .................... Select ON to display an image emphasizing on the color
BRIGHTNESS
0
reproducibility.
OFF
sRGB
• When sRGB is ON, COLOR MATRIX, COLOR TEMP. and
COMPUTER
COLOR MATRIX
GAMMA COLLECTION can’t be ad justed.
COLOR
TEMP.
STANDARD
COLOR MATRIX ......... Adjusts the color balance in each color of the image. See page 18.
COLOR TEMP. .... Adjusts the color temperature. See page 18.
COLOR
0
COLOR ................ Adjusts the color intensity of the image. (Available only when
TINT
0
VIDEO is selected as the source.)
SHARPNESS
0
TINT .................... Adjusts the color balance of the image. The color balance of the
GAMMA MODE
AUTO
image shifts green as the number increases and shifts to purple
as the number decreases. (Available only when VIDEO is
selected as the source.)
• When the TV50 (PAL, SECAM) signal is inputted, TINT can’t be adjusted.
SHARPNESS ....... Adjusts the image sharpness. The image sharpness rises as the number increases.
GAMMA MODE ... When AUTO is selected, the appropriate gamma mode is automatically selected depending on the
input signal. For normal use, select AUTO. Select DYNAMIC for computer sources. Select
STANDARD for sport scenes and video sources. Select THEATER for projecting film sources.
2 INSTALLATION
RIS ....................... Adjusts the sensitivity of the function (RIS) which automatically
opt.
XGA60
adjusts the brightness and contrast of the image depending on
the degree of the light in the room. When using this projector in INSTALLATION
a room where the light and shade varies slightly, select 1. When
RIS
OFF
using this projector in a norually lighted room, select 2. When
AUTO POWER
OFF
ON
using this projector in a room where the light and shade varies
AUTO POWER
OFF
OFF
greatly, select 3.When you select OFF, RIS won’t operate.
SPLASH SCREEN
ON
• When the sensitivity is adjusted in a large amount, the
BACK
COLOR
BLUE
image may be displayed solid white. Adjust the sensitivity
depending on the operating environment and imges to be
MUTE MODE
BLACK
displayed.
LAMP MODE
STANDARD
AUTO POWER ON ...... Select ON to boot up the projector automatically by turning on
OFF
IMAGE REVERSE
an externally connected power switch such as a breaker even
when the main power switch of the projector is off. Use this
setting when the projector is hanging from the ceiling.
• The projector will be in the stand-by mode when the lamp is off. Use the remote control to turn
on the lamp.
AUTO POWER OFF .... Set the time elapsed before the projector enters into the stand-by mode when there is no signal
inputted from the selected source.
SPLASH SCREEN ....... Select ON to display the splash screen when the power is turned ON.
• The splash screen can be changed. For more details, please consult your dealer.
BACK COLOR ...... Use to select the background, BLUE, BLACK or LOGO, which will be displayed when there is no
signal inputted from the selected source. When the LOGO is selected, the splash screen will be
displayed.
MUTE MODE ...... Use to select the background, BLACK or LOGO, which will be displayed when the MUTE button is
pressed. When the LOGO is selected, the splash screen will be displayed.
LAMP MODE ....... Use to change the brightness of the lamp. When LOW is selected, the image will become darker,
though the power will be saved, operating sound will be reduced.
• The intensity of the lamp will be STANDARD for 2 minutes regardless of the setting of the LAMP
MODE when the lamp turns on.
• When the LAMP MODE is changed, the screen may flicker. This is not a failure of the lamp.
IMAGE REVERSE ...... Use to reverse or invert the projected image. Select MIRROR in rear projection. Select MIRROR,
INVERT in rear projection with the projector hanging from the ceiling.
• When no signal is supplied for 6 hours with BACK COLOR set to BLACK, it changes to BLUE
automatically for the purpose of protecting the projector.
• When you continue projection for a long time with BACK COLOR or MUTE set to LOGO, an after-image
may persist on the screen.
• When the signal is lost during muting with MUTE set to LOGO, AUTO POWER OFF is ignored even
though it is active.
ON
EN – 16
•
•
•
•
•
•
•
opt.
XGA60
FEATURE
A
A
A
A
?
AË
MENU POSITION
1.
EXPAND MODE
1.
FRAME POSI.
3.
VIDEO SIGNAL
AUTO
SCART INPUT
OFF
ANAMORPHIC
OFF
3D CineView
ON
LANGUAGE
English
OK
RESET ALL
LANGUAGE ........ Use to select the language used in the menus. (
/ English / Español / Deutsch / Français / Italiano
/
/
/
)
/
RESET ALL ......... Use to reset the MENU settings (except LANGUAGE).
When SCART is set to ON, nothing is output to the external monitor.
When SCART is set to ON, normal computer signals are not projected.
Use SCART-BNC (or SCART-Mini D-SUB 15P) cable (option), when connecting with AV device equipped with
the SCART terminal.
Some AV devices equipped with the SCART terminal may not be compatible with the projector.
When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of
VIDEO SIGNAL depending on the input signal in such cases.
When 3D Cine View is switched from OFF to ON, you can check the motion detection operation about three seconds.
The buttons on the remote control don’t work during this period, which isn’t a failure.
When the LANGUAGE in FEATURE menu is set to English and NTSC video format is selected, the brightness is
decreased 15 points by set-up cancel function for U.S. (The indicated value is not changed.) The image becomes darker,
but this is not a failure of the projector.
4 SIGNAL
MEMORY CALL .......... Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION ...... Use to adjust the horizontal position of the image.
VERT. POSITION ........ Use to adjust the vertical position of the image.
FINE SYNC. ......... Use to synchronize the projector with PC input signals so that
the image is not blurred.
TRACKING .......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT ...... The unit adjusts itself automatically when connected to a DVD
player with a component video output (Y, CB, CR). In the case ( Y,
PB, PR). In the case the projector is connected to equipment that
includes RGB output terminal, adjust to RGB mode.
HOLD .................. Adjusts the image when flagging occurs near the top of the
screen.
opt.
XGA60
SIGNAL
A
U
MEMORY CALL
AUTO
HORIZ. POSITION
0
VERT. POSITION
0
FINE SYNC.
0
TRACKING
RRGGBB
0
COMPUTER INPUT
RGB
HOLD
USER
MEMORIZE
5 SIGNAL - USER (Normally, there is no need for adjustments.)
SIGNAL-USER
CLAMP POSITION/
CLAMP WIDTH .......... If you use something similar, the brighter colors of the projected CLAMP POSITION
image may become blurred. In this case, adjust CLAMP POSITION CLAMP WIDTH
or CLAMP WIDTH.
HORIZ. PIXELS
HORIZ.PIXELS .... Use to adjust the width of the image. The image size grows wider as VERT. LINES
the number increases. (Adjust to the horizontal pixels of the input VERT. SYNC.
signal for normal setting.)
VERT.LINES ....... Use to adjust the height of the image. The image size grows higher SHUTTER(U)
as the number increases. (Adjust to the vertical lines of the input SHUTTER(L)
SHUTTER(LS)
signal for normal setting.)
VERT.SYNC. ........ Use to adjust the image when its motion does not run smoothly. SHUTTER(RS)
Select AUTO for normal setting.
SHUTTER(U) ....... Use to adjust the image when the noise etc. appears on top part of
image.
SHUTTER(L) ....... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) ..... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ..... Use to adjust the image when the noise etc. appears on right side of image.
AUTO
DELETE
DEFAULT
0
0
0
0
AUTO
0
0
0
0
• When the setting of the SIGNAL-USER menu is changed, the image may not be displayed correctly. In this case, select
DEFAULT in the SIGNAL menu, and press the ENTER button.
EN – 17
ENGLISH
3 FEATURE
MENU POSITION ....... Use to select the position of the menu on the screen,
(upper
left) or
(lower right).
EXPAND MODE .. Select the mode for enlarging screen. See page 20.
FRAME POSI. ...... Sets the position of sub screen. See page 20.
VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is
automatically selected depending on the input signal. If the
image isn’t displayed correctly, select the desired video format
manually.
SCART ................. Select ON when connecting with a device equipped with the
SCART terminal that can output RGB signal. SCART terminal
is used mainly in Europe. Select OFF normally.
ANAMORPHIC .... Select the desired position, UPPER, CENTER or LOWER when
playing DVD discs containing data of letterboxed images.
3D Cine View ........ Select OFF to disable the line-doubler. Select ON normally.
Picture adjustment
User memory for signal setting
This projector can memorize the maximum of 2 signal
menu settings.
Memorizing the setting
1. Select MEMORIZE in the SIGNAL menu, and press
the ENTER button.
2. Press the $ or % button to select the memory which you
wish to record (USER 1 or USER 2).
3. Press the ENTER button.
• Any buttons are ineffective about 3 seconds of
recording setting. Wait for recording to have been
completed before operating the buttons.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the
$ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1. Select DELETE in the SIGNAL menu, and press the
ENTER button.
2. Press the $ or % button to select the memory which you
wish to reset (USER 1 or USER 2).
3. Press the ENTER button.
The recorded setting will be reset.
• Any buttons are ineffective about 3 seconds of
resetting the recorded setting. Wait for resetting to
have been completed before operating the buttons.
sRGB
0
COLOR TEMP.
STANDARD
COLOR
0
TINT
0
0
AUTO
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu. Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu. Press the %
button to lighten the image and the $ button to
darken the image.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu. Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu. Press the % button
to increase the amount of green in the image and the
$ button to increase the amount of red in the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu. Press the %
button to make the picture seem sharper and the $
button to make it softer.
EN – 18
3. Press the ENTER button.
COLOR MATRIX
RED
0
YELLOW
0
GREEN
0
CYAN
0
BLUE
0
MAGENTA
0
SATURATION
0
RGB-TINT
0
6. Repeat steps 4 and 5 for more adjustments.
OFF
COMPUTER
GAMMA MODE
.
5. Press the $ or % button to adjust the color balance
of the color.
COLOR MATRIX
SHARPNESS
2. Press the $ or % button to select USER
0
IMAGE
BRIGHTNESS
1. Select COLOR MATRIX in IMAGE menu.
XGA60
You can adjust the picture by using the IMAGE menu.
CONTRAST
This feature adjusts the color balance in each color of
RGB (Red, Green, Blue), and their neutral colors
(yellow, cyan, magenta) by using Color correction
adjustment. Use Color correct adjustment when
enphasizing a specific color, or when only a certain
color balance is not correctly adjusted.
4. Press the { or } button to select the desired color.
• If you wish to adjust the color intensity of the
image, select SATURATION.
• If you wish to adjust the all color balance of the
image, select TINT.
Adjusting the image
opt.
Color matrix
7. Exit the menu system by pressing the MENU button several times.
• When using the setting which has been already
prepared, select desired position VIDEO or
COMPUTER in step 2. When the source is selected
to VIDEO or S-VIDEO, VIDEO will be selected
automatically. When the source is selected to
COMPUTER, COMPUTER will be selected
automatically.
• When not using Color matrix adjustment, select
OFF in step 2.
1. Select COLOR TEMP in IMAGE menu.
2. Press the $ or % button to select USER
.
3. Press the ENTER button.
COLOR TEMP.-USER
CONTRAST R
0
CONTRAST B
0
BRIGHTNESS R
0
BRIGHTNESS B
0
4. Press the { or } button to select the desired item.
5. Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU button several times.
About color temperature
There are different kinds of white color. Color temperature is
a way to show the differences. The white, which temperature
is low, becomes reddish white. When the color temperature is
higher, the white becomes more bluish. This projector sets
this color temperature by changing the numbers of contrast
blue and red.
To set the color temperature high:
Set the contrast B (Blue) number high, and the contrast R
(Red) number low.
To set the color temperature low:
Set the contrast B (Blue) number low, and the contrast R
(Red) number high.
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers. In this case, press the AUTO POSITION
button. If the images are still not projected correctly,
use the MENU display to adjust the projected images.
ENGLISH
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
Color temperature
SIGNAL-USER
CLAMP POSITION
0
CLAMP WIDTH
0
HORIZ. PIXELS
0
VERT. LINES
0
VERT. SYNC.
AUTO
SHUTTER(U)
0
SHUTTER(L)
0
SHUTTER(LS)
0
SHUTTER(RS)
0
Wide strips appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise appears on right or left side of image :
Adjust SHUTTER (LS), SHUTTER (RS) or HORIZ.
PIXELS of the menu in SIGNAL - USER menu.
Noise appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT.
LINES of the menu in SIGNAL - USER menu.
Top part of image curves :
Change the setting of HOLD in SIGNAL menu.
Select ON , press the ENTER button and adjust
BEGIN or END for image which top part is the least
curved.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL USER menu. Select AUTO for normal setting.
curved. Select AUTO for normal setting.
• Do not change each menu setting in USER menu
for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
3. Select TRACKING in SIGNAL menu.
opt.
XGA60
SIGNAL
A
U
MEMORY CALL
AUTO
5. Repeat steps 1 to 4 for fine adjustment.
HORIZ. POSITION
0
6. Select VERT. POSITION in SIGNAL menu.
VERT. POSITION
0
FINE SYNC.
0
7. Press the$ or % button to adjust the vertical
start position (the top end of image).
TRACKING
RRGGBB
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
0
COMPUTER INPUT
RGB
HOLD
USER
MEMORIZE
AUTO
DELETE
DEFAULT
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu. Press
the % button to move the image to left. Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu. Press
the % button to move the image to upward. Press
the $ button to move the image to down.
EN – 19
Advanced features for presentation
Setting the Expand mode
1. Press the MENU button.
REAL screen display
• During REAL mode, Press the $ or % buttons
for fine adjustment.
• During REAL mode, the { and } buttons are
not working. At this time, the prohibition mark
( ) appeares on the screen.
• The expanding rate cannot be changed by pressing either the + or - button.
2. Press the $ or % to select the FEATURE menu.
Picture in Picture (PinP)
Expand
By pressing the EXPAND button on the remote control, you can magnify the detailed image of the picture.
You can also view the screen displaying the picture as
its original size (native resolution display).
3. Press the ENTER button.
4. Press the { or } button to select EXPAND MODE
or FRAME POSI.
5. Press the $ or % to set the EXPAND MODE or
FRAME POSI.
6. Press the MENU button twice to exit the menu system.
EXPAND MODE
(EXPAND MODE 1) (EXPAND MODE 2) (EXPAND MODE 3) (EXPAND MODE 4)
Normal
image
Zooming Zooming
image
image
Normal
image
Zooming
image
Native resolution
display
FRAME POSI.
(FRAME POSI.
1~4)
1
2
4
3
(FRAME POSI. 5)
One of the special features of this unit is the picturein-picture (PinP) mode. PinP allows you to view different sources at the same time.
Using the PinP mode
1. Press the PinP button on the remote control.
• When the image from VIDEO IN or S-VIDEO
IN terminal is displayed on the screen, the image from COMPUTER IN terminal is displayed
as sub-image.
• When the image from COMPUTER IN terminal
is displayed on the screen, the image from VIDEO
IN or S-VIDEO IN terminal is displayed as subimage.
2. If necessary, select the desired external input source
of the image by using the VIDEO or COMPUTER
button.
To switch Main image and Sub image
3. Press the { or } buttons on the remote control.
To change frame position
4. Press the $ or % buttons on the remote control.
Main
image
Sub
image
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active picture by pressing the {, }, $, % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button twice on the remote control.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
• In EXPAND mode, you cannot adjust the zoom/focus and the volume.
• The Expand mode may not function depending on
the input signal. For more details, refer to page 28
or 29.
FRAME POSI.
(FRAME POSI.
1~4)
1
2
4
3
(FRAME POSI. 5)
Main
image
Sub
image
5. Press the PinP button on the remote control.
The sub image will be disappear.
• Adjusting contrast, brightness, tint or color is not
available in PinP mode.
• In PinP mode, both Main image and Sub image
are displayed with their frames skipped.
• In PinP mode, the audio of the Main image is
outputted.
• In PinP mode, the images may not move smoothly.
• The PinP mode may not function depending on the
input signal. For more details, refer to page 28 or
29.
• The UXGA signal isn’t displayed as a sub image.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will freeze temporarily.
To resume picture activity.
2. Press the STILL button on the remote control again.
EN – 20
By connecting to personal computer through the USB or PS/2 port, you can operate your computer with the
projector remote control.
Projector + computer with USB connector
to USB port
to USB
USB cable
USB 4P
(type A)
USB 4P
(type B)
• You can use the mouse remote control function with a computer supporting USB only. If your system is
Windows® 98 or higher, your computer supports USB in standard. If your system is Windows® 95 or lower,
please contact your dealer. If your computer is Macintosh® with USB port, you can use this function.
• When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this
case, restart the projector and the computer. If possible, you should disconnect the USB cable when the lamp
is turned ON.
Projector + computer with PS/2 connector
PS/2 adaptor
to RS-232C
terminal
RS-232C cable
to mouse
(PS/2) port
Mini DIN 6P
D-SUB 9P
D-SUB 9P
Mini DIN 8P
• Turn off computer and the projector before connecting with PS/2 port. When connecting the computer with the
projector when the personal computer is on, the remote control does not work as a mouse. In that case, restart
the personal computer.
• When the projector is connected with USB terminal and RS-232C terminal at the same time, only the terminal which the projector recognizes first will work.
• When you use the RS-232C cable together with an extension cable, the function may not work correctly.
Operation
COMPUTER
2
1
VIDEO
KEYSTONE
EXPAND
1
2
P in P
AUTO POSITION
VOLUME
LASER
left click
This operates in the same
way as the left button on
the computer mouse.
mouse pointer
Use to move the cursor on the image,
instead of the computer mouse.
MENU
R-CLICK
ENTER
MUTE
STILL
16 : 9
R-CLICK
This operates in the same way as the right
button on the computer mouse.
EN – 21
ENGLISH
Mouse remote control
Lamp replacement
The lamp is designed to project the image on the LCD
panels. When the lamp no longer functions, replace it
with a new one.
Caution:
• Do not remove the lamp immediately after using
the projector, you may get burned because of the
high temperature of the lamp.
• When you replace the lamp, press the power button
to power off, then wait for 120 seconds in stand-by
mode to allow the lamp and LCD panels to cool. Turn
off the main switch, unplug the power cord from
the outlet, and wait one hour so that the lamp is
cooled to the touch.
• Do not remove the lamp except for replacement.
Careless treatment can cause injury or fire.
• Do not touch the lamp element directly. It may break
and cause you to injure or burn yourself.
• Be sure not to drop the lamp lid screw into the projector. Also be sure not to insert metal or any flammable objects, it may cause fire or electric shock. If
any objects are inserted, please unplug and contact
your dealer.
• Install the lamp securely, failure may cause a fire.
• If the light bulb part breaks, some small glass fragments may fall out through the small cooling grill,
and sticks to the inside of projector or the lamp box.
When taking the lamp out, make sure to turn over
the projector and hold the handle of the lamp box to
avoid injury from the glass fragments.
• Never shake the lamp or hold it in front of your face
after removing the lamp box. The glass fragments may
fall out and cause injuries to your
eyes and so on.
1. Reverse the projector gently.
2. Loosen the screws of the lamp lid
(a) using a Phillips screwdriver (+),
and remove the lid.
• Remove the lamp cover in the direction of the arrow as indicated.
a
b
3. Loosen screws (b) using a Phillips
screwdriver (+), and remove them.
4. Pull up the handle.
5. Hold onto the projector by the handle
as you pull out the lamp.
• Pull the lamp out of the projector slowly.
Should the light bulb be broken, glass fragments will spill out if the lamp is pulled
out too quickly.
• Once the lamp has been removed, do
not spill liquid on it, place it near flammable objects or where children can
touch it. Otherwise, it will cause injury or fire.
8. Tighten up the screws (b) using a
Phillips screwdriver (+).
EN – 22
a
How to reset the operation time
meter
Plug in the power cord, switch on the projector, and
reset lamp time by pressing the $, % and POWER
buttons on the contro panel simultaneously.
Important:
• If the 3 buttons was not pressed at the same time,
the lamp time may not be reset.
• Please confirm the TEMP indicator illuminates
about 2 seconds and the lamp time has been
reset.
• The projector will not turn on if you do not secure
the lamp lid.
• You must reset the operation time meter after you
replace the lamp.
• Do not reset the operation time meter unless the
lamp has been replaced.
Caution:
• Do not spill liquid on the lamp or place it near flammable objects or where children can touch it. Otherwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted
between the right and left lamp guides.
Interval of the lamp replacement
The interval of the lamp replacement about 1,500 hours of
consecutive use. Replacement span may differ according to
operating environment, and may be shorter than 1,500 hours.
Decreases in luminescence and/or color brightness will indicate that the light source lamp needs to be replaced. When
lamp operation time exceeds 1,000 hours*1, the indicator
will flash alternately between green and red (while the lamp
is in operation; when the lamp is not in operation, the indicator will appear red only) and the lamp replacement message will appear on the screen for one minute everytime the
power is turned on. When the lamp has been used for about
1,400 hours*1, the replacement message (LAMP:>1400H)
will appear on the screen for one minute everytime 10 hours
after. When the lamp has been used for about 1,500
hours*1,*2, the projector will automatically shut off for safety
and the power indicator light will be red. The projector cannot be used until the lamp has been replaced and operation
timer has been reset.
Caution:
• The lamp is fragile. If broken, be careful not to cut yourself with glass fragments.
• The replacement span of the lamp depends on the environment. For replacement lamps, please contact your
dealer.
The projector automatically shuts off when the
lamp is used up in about 1,500 hours*1,*2 and cannot
be used until the lamp is replaced and the internal
timer is reset.
6. Insert the new lamp securely into the
projector body in the right direction.
7. Put the handle back to the holding
point.
• Make sure that the handle is
locked.
9. Tighten up the screws of the lamp lid
using a Phillips screwdriver (+).
*1) When LAMP MODE of the INSTALLATION
menu is set to STANDARD.
*2) When LAMP MODE is set to LOW, the duration
will be extended maximum up to 2,000 hours.
b
Caution:
Be sure to turn off the projector and unplug the power
cord from the wall outlet before you perform any maintenance on the projector.
Cleaning the air-filter
Clean the air-filter frequently (about once a month). If
the filter or ventilation slots become clogged with dirt
or dust, the temperature inside of the projector may
rise and cause some troubles, such as damage of inside parts, and shortening the life of panel.
• When the temperature inside of the projector
rises, the TEMP indicator blinks in red, and the
power will be shut off to be stand-by which LAMP
indicator is turned off.
Caution:
Be sure to use the projector with an air-filter. If not,
dust may get inside the projector, causing a fire or a
breakdown.
Cleaning the projector and the ventilation
slots
Use a soft cloth to clean the projector and the ventilation slots. When the slots become dirty, wipe them with
a soft cloth dampened with a diluted mild detergent,
and then wipe them with a dry cloth.
To protect the surface of the projector from fading or
deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials come into
contact with the projector.
Filter cover
1. To remove the filter cover, slide
the cover in the direction of the
arrow.
Cleaning the lens
2. Remove the air-filter from the filter cover.
3. Wash the air-filter or change to the new filter.
• Use water or a mild detergent diluted with
water to clean the filter. Rinse the filter
thoroughly and let it dry completely.
4. Attach the air-filter to the
filter cover.
• Attach the air-filter so
that it is retained by the
four holders on the filter
cover. Then spread the
air-filter flat on the
filter cover by pressing
it. (Make sure that the
filter is catching on the
protrusions, which
prevent displacement
of the air-filter.)
Important:
• If the filter is damaged or becomes extremely
dirty, change to the provided new filter. If you
wish to another new filter, contact your dealer for
replacement.
• The power will not turn on if the air-filter cover is
improperly installed.
Use a standard lens-cleaning brush or a piece of lens
tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive lenscleaning materials. Do not touch the lens with your fingers.
Protrusions
Holders
Air-Filter
5. Attach the filter cover to the projector.
• Make sure that the air-filter is attached
correctly without displacement.
EN – 23
ENGLISH
Maintenance
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult
this chart before contacting your dealer.
PROBLEMS
The power is off.
CAUSE
• The air inlet slots, outlet slots or air filter is
clogged with dust or some objects.
POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
POWER indicator blinks red.
• The projector has been turned on again too soon
after having been turned off.
• When the power switch was turned off while
the fan was running, during or after lamp
operation.
• The room temperature is too high.
(Does the LAMP indicator show an unusual
condition?)
• Lamp is no longer working.
POWER indicator blinks between red and green.
• The filter cover is not closed.
• When the LAMP indicator or the TEMP
indicator is either on or blinking, the main unit
requires repairs.
No picture appears • Lens is covered by lens cap.
on the screen.
• When the LAMP indicator or the TEMP
indicator is either on or blinking, the main unit
requires repairs.
• The equipment connected to this projector is not turned on.
• Hookup is not made correctly with other equipment.
• The input source is not selected correctly.
The image is
turned off.
The image is
distorted.
POSSIBLE SOLUTIONS
• Remove the object.
•
•
•
•
Plug the power cord into the outlet.
Insert the power cord into the projector.
Turn the main switch on.
Close the lamp lid.
• Wait for the lighting sequence.
• Turn the power switch on and off several times.
• Refer to "Indicators" on page 25.
• Replace the lamp with a new one.
• Close the cover correctly.
• Contact your dealer.
• Take the lens cap off.
• Replace the lamp with a new one.
• Turn on the connected equipment.
• Confirm the hookup.
• Select the correct source according to the equipment connected to this projector.
• The air inlet slots, outlet slots or air filter is
clogged with dust or some objects.
(In this case, the TEMP indicator does not light up.)
• Remove the object and turn off the main power
switch. After about 10 minutes, Turn the projector on.
• The projector is not at a right angle to the screen.
• Adjust the angle of the projector to make a right
angle to the screen. See page 12.
The image is dark. • Brightness, tint and color are not adjusted correctly.
The image is
• The projecting distance is beyond the focused area.
blurred.
• Lens is dirty.
• Screen size exceeds screen size specifications.
• Adjust brightness, tint and color correctly.
Brightness and contrast are not adjusted correctly.
FINE adjustment is not made correctly.
Tracking is not adjusted.
The projector is not at a right angle to the screen.
Adjust brightness, contrast.
Make FINE adjustment.
Adjust tracking.
Adjust the angle of the projector to make a
right angle to the screen. See page 12.
•
•
•
•
The afterimage
remains.
•
•
•
•
•
•
•
Adjust the projecting distance. See page 9.
Clean lens.
Reduce screen size to within 40" to 300".
• When a stationary image is projected for a long time, its afterimage may persist on the screen. This
is not a failure, and the afterimage will disappear in a few minutes.
Red, blue or green dots are • It is normal.
viewed on the text of image.
The image is distorted on the screen
and noise is heard.
• The cable for connection with other equipment
is not plugged securely into the terminal.
• The projector is installed too close to other
equipment.
• Plug the connecting cable securely into the
terminal. See pages 10-11.
• Install the projector far away from other equipment.
No sound is heard.
• Volume is not turned up.
• Connection to other equipment is not made correctly.
• Turn up the volume.
• Check connections. See pages 10-11.
Nothing is displayed on
the PC monitor.
Warm air comes out of
the exhaust vents.
• The PC monitor is not turned on.
• Turn on the monitor.
Adjustments cannot be
made.
is displayed.
EN – 24
• This is typical of the LCD projector.
• The operation is incorrectly made due to noise or • Press the reset button on the Terminal board.
See page 15.
interference.
• This mark is displayed when an invalid operation is executed (for example, when the COMPUTER or
VIDEO button is pressed while the menu is displayed). This is not failure.
The projector has three indicators each of which shows the working condition of the projector.
The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your
dealer.
TEMP indicator
LAMP indicator
POWER indicator
Normal condition
POWER LAMP TEMP
Steady
red
Off
Off
Steady
green
Blinking
green
Off
Steady
green
Steady
green
Off
CONDITION
Notes
Stand-by
Lamp stand-by (about for 1 minute)
The power button cannot be used to switch
OFF.
The POWER is ON. (Normal condition)
Abnormal condition
POWER LAMP TEMP
CONDITION
POSSIBLE SOLUTIONS
Unusual temperature
Steady
green
Steady
green
Blinking
red
Steady
red
Off
Blinking
red
Steady
red
Blinking
green
Off
Steady
green
Blinking
green/red
Off
Lamp duration warning. (Lightning duration total
about 1, 000 hours*.When the POWER is ON.)
Steady
red
Blinking
red
Off
Lamp duration warning. (Lightning duration total
about 1, 000 hours*.When the POWER is OFF.)
Steady
red
Steady
red
Off
Lamp duration warning. (Lightning duration total
about 1,500 hours*.)
Blinking
green/red
Off
Off
Steady
or
Steady
or
Blinking
Blinking
• The ventilation slits or air filter is clogged with
dust or debris.
• The room temperature is too high.
• The filter is dirty.
• Remove the object from the ventilation
slits.
• Relocate the projector to a cooler place.
• Clean the filter.
The protection circuit is working or the lamp is in an
abnormal condition.
• Wait until the LAMP indicator is turned
off, then press the POWER button.
• If the above operation is not effective,
replace the lamp.
(The indicators operate as shown on the left at the time of power-off, too.
In this case, they are’nt indicating an abnormal condition.)
Replace the lamp.
Exchange with a new lamp if the same
problem recurs.
The lamp or filter cover is not closed.
Close the cover correctly.
Abnormal.
Contact your dealer.
Blinking
green/red
*) When LAMP MODE of the INSTALLATION menu is set to STANDARD.When it is set to LOW, the duration will be extended.
EN – 25
ENGLISH
Indicators
Specifications
Type
Model
Rated power supply
Rated input
LCD panels
LCD projector
XL30U|XL25U|SL25U
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
16,770,000 colors
AC100 - 240V, 50 / 60Hz
3.7 A
XL30U/XL25U
1.0-inch LCD panel: 3 pieces (for R, G, B)
Pixels 1,024 × 768 = 786,432 pixels
Total 2,359,296 pixels
Active pixel rate: 99.99 % or more (each panel)
F 1.7 - 2.2
SL25U
1.0-inch LCD panel: 3 pieces (for R, G, B)
Pixels 800 × 600 = 480,000pixels
Total 1,440,000 pixels
Active pixel rate: 99.99 % or more (each panel)
f = 37 - 46 mm
270 W SHP
40 - 300 inch (aspect ratio 4:3)
Resolution :
640 x 400 - 1024 x 768 + Compressed 1600 x 1200 (XL30U/XL25U)
640 x 400 - 800 x 600 + Compressed 1280 x 1024 (SL25U)
Sync on Green available
Video compatibility
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
DVD (Component) / HDTV (1080i) / 720p / (525p)
Audio output
Speaker
S-video input
3 W Mono
Round type (8Ω 3W) × 1
Luminance signal: 1.0 Vp-p 75Ω
(negative sync.)
Chroma signal: 0.286 Vp-p 75Ω (burst signal)
Video input
Audio inputs
Analog RGB input
(mini D-SUB 15P/BNC)
1.0 Vp-p 75Ω (negative sync.)
350 mVrms, 10kΩ or more
RGB: 0.7Vp-p 75Ω (negative sync.)
YPBPR(YCBCR):
Y:1.0Vp-p (negative sync.)
PBPR(CBCR):0.7Vp-p
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
PC audio input
Control connector
350 mVrms, 10kΩ or more
ø3.5mm stereo mini jack
Serial (Mini DIN 8 pin female connector) RS-232C standards
USB terminal for Mouse, Wired remote terminal
Outside dimensions
380 × 157 × 307 mm
(width × height × depth)
Weight
Length of power cord
Temperature, humidity
(performance guarantee)
Legs and lens are included.
Approx. 5.9kg
114 inch (2.9m)
+41°F (+5°C) - +95°F (+35°C), 30~90%
Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the Kensington System for instructions on how to use it to
secure the projector. Please contact to Kensington Technology Group as shown below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : (650)572-2700
EN – 26
Fax : (650)572-9675
RS-232C (Mini DIN 8P)
12
COMPUTER IN/OUT
(Mini D-SUB 15P)
5
1
10
3
PIN No.
SPEC
1
R(RED)/CR
2
G(GREEN)/Y
3
B(BLUE)/CB
4
GND
5
6 8
NAME
I/O
5
GND
1
TXD
IN
6
GND
2
RTS
IN
7
GND
3
DTR
IN
8
GND
4
GND
–
9
–
5
CTS / 5V
IN/OUT
10
GND
6
DCD / CLOCK
OUT
11
GND
7
RXD
OUT
12
DDC Data
8
RI / DATA
OUT
13
HD/CS
PIN No.
14
VD
15
DDC Clock
ENGLISH
Connectors
6
15
11
30
307
250
Dimensional drawings
(mm)
30
30
316.5
98
7.5
157
80
9.5
153
31
38
307
380
What’s included in the box
2 AC power cord
1
1
1
1
1
Audio/Video cable
RGB cable for PC
RS-232C cable
PS/2 adapter
USB cable (For XL30U only)
246C383-10
246C383-20
246C381-10
246C448-10
246C447-10
246C449-10
246C450-10
1
1
1
1
1
2
Filter
Remote control
Remote control cable
User manual
Quick reference card
Battery for remote
620D085-10
939P916-10
246C424-10
871D360-10
857D037-10
–
Replacement part
(Option / Not included in the box)
Spare marcury lamp
499B030-10
(VLT-XL30LP)
EN – 27
Specifications (continued)
Specification of RGB signals in each computer mode of the projector (For XL30U/XL25U)
Signal mode
TV60
TV50
1080i
525p
625p
720p
PC98
CGA70
CGA84
CGA85
VGA60
VGA72
VGA75
VGA85
VGA120
SVGA56
SVGA60
SVGA72
SVGA75
SVGA85
SVGA95
SVGA120
XGA43i
XGA60
XGA70
XGA75
XGA85
XGA120
SXGA70a
SXGA75a
SXGA85a
SXGA60b
SXGA75b
SXGA85b
SXGA43i
SXGA60
SXGA75
SXGA85
MAC13
MAC16
MAC19
MAC21
HP75
HP72
SUN66a
SUN76a
SUN66
SUN76
SGI72
SGI76
IBM60
UXGA
resolution
(H x V)
–
–
–
–
–
–
640 x 400
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 960
1280 x 960
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
640 x 480
832 x 624
1024 x 768
1152 x 870
1024 x 768
1280 x 1024
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
horizontal
frequency (kHz)
15.73
15.63
33.75
31.47
31.25
45.00
24.82
31.47
37.86
37.86
31.47
37.86
37.50
43.27
61.89
35.16
37.88
48.08
46.88
53.67
59.97
77.11
35.52
48.36
56.48
60.02
68.68
98.58
63.85
67.50
77.49
60.00
75.00
85.94
46.43
63.98
79.98
91.15
35.00
49.72
60.24
68.59
62.94
78.13
61.85
71.81
71.68
81.13
76.92
82.01
63.42
75.00
*1 : The Expand mode and the PinP mode don’t
function with this signal.
• When the EXPAND MODE of FEATURE menu is
set to real screen display, by pressing the EXPAND
button on the remote control, it will switch to the
screen displaying the picture as its original size (real
screen display). In the real screen display, pictures
will be black-framed when picture resolution is
lower than 1,024 x 768.
Important:
• Some computers may not be compatible with the
projector.
• The projector's maximum resolution is 1,024 x 768
pixels. It may not display correctly for the pictures
of higher resolutions than 1,024 x 768.
EN – 28
Vertical
frequency (Hz)
59.94
50.00
60.00
59.54
50.00
60.00
56.42
70.09
84.14
85.08
59.94
72.81
75.00
85.01
120.17
56.25
60.32
72.19
75.00
85.06
94.89
119.93
86.96
60.00
70.07
75.03
85.00
119.78
70.01
75.00
85.06
60.00
75.00
85.00
86.87
60.02
75.03
85.02
66.67
74.55
75.02
74.96
74.93
72.00
66.00
76.64
66.68
76.11
72.30
76.00
60.00
60.00
Normal mode
(H x V)
1024 x 768
1024 x 768
1024 x 576
1024 x 768
1024 x 768
1024 x 576
1024 x 640
1024 x 640
1024 x 640
1024 x 640
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
Real mode
(H x V)
–
–
–
–
–
–
640 x 400
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
–
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
–
1024 x 768
1024 x 768
1024 x 768
640 x 480
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
–
*1
*1
*1
*1
*1
• The picture with a SYNC on G (Green) signal
may jitter.
• The picture with a SYNC on G (Green) signal may
be tinged with green.
• If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible resolution and frequency.
• Set the COMPUTER INPUT in SIGNAL menu to
RGB, when inputting the HDTV signal as RGB signal.
• In case of the SXGA, the right side of the image
may not appear. In this case, adjust the TRACKING in the SIGNAL menu.
Signal mode
TV60
TV50
1080i
525p
625p
720p
PC98
CGA70
CGA84
CGA85
VGA60
VGA72
VGA75
VGA85
VGA120
SVGA56
SVGA60
SVGA72
SVGA75
SVGA85
SVGA95
SVGA120
XGA43i
XGA60
XGA70
XGA75
XGA85
SXGA70a
SXGA75a
SXGA85a
SXGA60b
SXGA75b
SXGA43i
SXGA60
SXGA75
MAC13
MAC16
MAC19
MAC21
HP75
HP72
SUN66a
SUN76a
SUN66
SUN76
SGI72
SGI76
IBM60
resolution
(H x V)
–
–
–
–
–
–
640 x 400
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 960
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
640 x 480
832 x 624
1024 x 768
1152 x 870
1024 x 768
1280 x 1024
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
horizontal
frequency (kHz)
15.73
15.63
33.75
31.47
31.25
45.00
24.82
31.47
37.86
37.86
31.47
37.86
37.50
43.27
61.89
35.16
37.88
48.08
46.88
53.67
59.97
77.11
35.52
48.36
56.48
60.02
68.68
63.85
67.50
77.49
60.00
75.00
46.43
63.98
79.98
35.00
49.72
60.24
68.59
62.94
78.13
61.85
71.81
71.68
81.13
76.92
82.01
63.42
*1 : The Expand mode and the PinP mode don’t
function with this signal.
• When the EXPAND MODE of FEATURE menu is
set to real screen display, by pressing the EXPAND
button on the remote control, it will switch to the
screen displaying the picture as its original size (real
screen display). In the real screen display, pictures
will be black-framed when picture resolution is
lower than 800 x 600.
Vertical
frequency (Hz)
59.94
50.00
60.00
59.54
50.00
60.00
56.42
70.09
84.14
85.08
59.94
72.81
75.00
85.01
120.17
56.25
60.32
72.19
75.00
85.06
94.89
119.93
86.96
60.00
70.07
75.03
85.00
70.01
75.00
85.06
60.00
75.00
86.87
60.02
75.03
66.67
74.55
75.02
74.96
74.93
72.00
66.00
76.64
66.68
76.11
72.30
76.00
60.00
Normal mode
(H x V)
800 x 600
800 x 600
800 x 450
800 x 600
800 x 600
800 x 450
800 x 500
800 x 500
800 x 500
800 x 500
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
Real mode
(H x V)
–
–
–
–
–
–
640 x 400
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
–
800 x 600
800 x 600
800 x 600
800 x 600
–
–
–
–
–
–
–
–
640 x 480
800 x 600
800 x 600
–
800 x 600
–
–
–
–
–
–
–
–
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
• The picture with a SYNC on G (Green) signal may
be tinged with green.
• If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible resolution and frequency.
• Set the COMPUTER INPUT in SIGNAL menu to
RGB, when inputting the HDTV signal as RGB
signal.
Important:
• Some computers may not be compatible with the
projector.
• The projector's maximum resolution is 800 x 600 pixels. It may not display correctly for the pictures of
higher resolutions than 800 x 600.
• The picture with a SYNC on G (Green) signal
may jitter.
EN – 29
ENGLISH
Specification of RGB signals in each computer mode of the projector (For SL25U)
LCD Projector
XL30U / XL25U / SL25U
This projector can be controlled by connecting a personal computer with RS-232C terminal.
PC-controllable functions :
• Turning the power ON or OFF
• Changing input signals
• Inputting commands by pressing the buttons on the control panel and remote control
• Menu setting
Connection
to RS-232C
terminal
RS-232C cable
to Com1
Comport
D-SUB 9P
Mini DIN 8P
Important:
• Make sure that your computer and projector are turned off before connection.
• Turn on the projector after the computer is started up.
(If you do not follow this instruction, the Comport may not function.)
• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bits]
PARITY BIT
STOP BIT
NONE
1 [bit]
FLOW CONTROL
NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable,the reverse type cable should be used.
2) Control command diagram
The command consists of the address code, function code, data code, and end code. The length of the command
varies among the functions.
HEX
Address code
30h 30h
Function code
Function
Data code
Data
'0' '0'
Function
Data
ASCII
[Address code]
[Function code]
[Data code]
[End code]
End code
0Dh
30h 30h (In ASCII code, '0' '0') fixed.
A code of each fixed control move.
A code of each fixed control data (number) and not always indicated.
0Dh (In ASCII code, ' ') fixed.
1
3) Control sequence
(1) Send the command from the personal computer to the projector. (The commands shall be sent at intervals
of at least 400ms.)
(2) The projector will send a return command 400ms* after it receives an end code. If the command is not
received correctly, the projector will not send the return command.
(3) The personal computer checks the command and confirms if the sent command has been executed or not.
(4) This projector sends various codes other than the return code. When having a control sequence by RS232C, reject other codes from the personal computer.
* : The sending time of return command may delay depending on the (operating conditions) during changing
the input signal, etc.
[Example] When turning the power ON (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
Status code from
from the PC, etc.
30 30 21 0D
'0' '0' '!' '
Description
the projector
Command for POWER ON
'
30 30 21 0D
Command receipt confirmation
'0' '0' '!' '
(Command echo back)
'
• Any commands will not be executed for 10 seconds after the power is turned on.
4) Operation commands
The operation commands are used for the basic operation setting of this projector. They may not be executed
while the signals are changed. The operation commands have no data codes.
Operation
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT VIDEO 1
INPUT VIDEO 2
ASCII
!
"
_r1
_r2
_v1
_v2
HEX
21h
22h
5Fh
5Fh
5Fh
5Fh
Note
72h
72h
76h
76h
31h
32h
31h
32h
This command will not be executed for 1 minute after the power is turned off.
This command will not be executed for 1 minute after the power is turned on.
This command will not be executed in Stand-by mode or the MUTE is executed.
This command will not be executed in Stand-by mode or the MUTE is executed.
This command will not be executed in Stand-by mode or the MUTE is executed.
This command will not be executed in Stand-by mode or the MUTE is executed.
[Example] When setting the input signal to COMPUTER 1 (Figures and symbols enclosed in quotation
marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code from
the projector
Description
30 30 5F 72 31 0D
'0' '0' '_' 'r' '1' ' '
Command for setting the input
signal to COMPUTER 1
30 30 5F 72 31 0D
'0' '0' '_' 'r' '1' ' '
Command receipt confirmation
(Command echo back)
5) Volume commands (Not executable in stand-by mode, while the Splash screen is projected or the MUTE is executed.)
The volume commands are used for the volume setting of this projector with the value.
ITEM
VOLUME
ASCII
VL
HEX
56h 4Ch
VALUE
00 - 31
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII
'0'
'1'
'2'
'3'
'4'
'5'
'6'
'7'
'8'
'9'
HEX
30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
[Example] When setting the volume to 15 (standard value) (Figures and symbols enclosed in quotation
marks are ASCII codes.):
Sending commands
from the PC, etc.
30 30 56 4C 31 35 0D
'0' '0' 'V' 'L' '1' '5' '
Status code from
Description
the projector
Command for setting the volume
'
30 30 56 4C 31 35 0D
Command receipt confirmation
'0' '0' 'V' 'L' '1' '5' '
(Command echo back)
'
2
6) Keystone commands (Not executable in stand-by mode, while the Splash screen is projected or the MUTE is executed.)
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM
KEYSTONE
ASCII
KS
HEX
4Bh 53h
VALUE
±30
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII
HEX
'+'
2Bh
'–'
2Dh
'0'
30h
'1'
31h
'2'
32h
'3'
33h
'4'
34h
'5'
35h
'6'
36h
'7'
37h
'8'
38h
'9'
39h
7) Mute commands (Not executable in stand-by mode or while the Splash screen is projected.)
The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h).
ITEM
MUTE
ASCII
MUTE
HEX
4Dh 55h
54h
45h
VALUE
0 (OFF), 1 (ON)
8) Remote commands
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
Button's name on remote
+ VOLUME
– VOLUME
KEYSTONE
EXPAND
PinP
MUTE
{
}
$
%
MENU
ENTER
AUTO POSITION
STILL
16 : 9
ASCII
r06
r07
r43
r02
r04
ra6
r53
r2b
r4f
r59
r54
r10
r09
ra4
re2
HEX
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
30h
30h
34h
30h
30h
61h
35h
32h
34h
35h
35h
31h
30h
61h
65h
36h
37h
33h
32h
34h
36h
33h
62h
66h
39h
34h
30h
39h
34h
32h
[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
Status code from
from the PC, etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
Description
the projector
Command operating the same
'
30 30 72 35 34 0D
as the MENU button
Command receipt confirmation
'0' '0' 'r' '5' '4' '
(Command echo back)
'
9) Reading command diagram
The projectors operating status, such as POWER-ON / OFF and the currently selected input terminal, can be
monitored.
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT VIDEO 1
INPUT VIDEO 2
ASCII
Function
Data (Receive)
vP
1
vP
0
vI
r1
vI
r2
vI
v1
vI
v2
Function
76h 50h
76h 50h
76h 49h
76h 49h
76h 49h
76h 49h
HEX
Data (Receive)
31h
30h
72h 31h
72h 32h
76h 31h
76h 32h
The PC sends the command without attaching the data code to it. On the other hand, the projector attaches
to the received command it’s current operating status as the data code and send it back to the PC.
[Example ] When checking the currently selected input terminal (when the INPUT VIDEO 1 is being selected) :
Sending commands
from the PC, etc.
30 30 76 49 0D
'0' '0' 'v' 'I' ' '
Status code from
the projector
Description
Command for checking the input terminal
30 30 76 49 76 31 0D
'0' '0' 'v' 'I' 'v' '1' ' '
Check result ( VIDEO 1)
3
10) Menu setting commands (Not executable in stand-by mode, while the Splash screen is projected or the MUTE is executed.)
The menu setting commands are used for the menu setting of this projector. If the personal computer sends the
command without attaching the data code, the projector attaches to the received command it’s current setting
value as the data code and send it back to the PC.
ITEM
CONTRAST *1
BRIGHTNESS *1
sRGB
COLOR MATRIX (MODE)
COLOR MATRIX (R, G, B)
COLOR MATRIX (Y, C, M)
COLOR MATRIX (SATURATION)
COLOR MATRIX (RGB-TINT)
COLOR TEMP.
COLOR
TINT
SHARPNESS
GAMMA MODE
RIS
AUTO POWER ON
AUTO POWER OFF
SPLASH SCREEN
BACK COLOR
MUTE MODE
LAMP MODE
IMAGE REVERSE
MENU POSITION
EXPAND MODE
FRAME POSITION
VIDEO SIGNAL
ASCII
P
Q
SRGB
CMT
MRGB
MYCM
MSAT
MT
A
T
S
R
GS
AI
APON
APOF
SS
BB
MM
LM
IR
MP
EX
FM
VS
HEX
50h
51h
53h
43h
4Dh
4Dh
4Dh
4Dh
41h
54h
53h
52h
47h
41h
41h
41h
53h
42h
4Dh
4Ch
49h
4Dh
45h
46h
56h
SCART
ANAMORPHIC
3D CineView
LANGUAGE
SRT
SC
LD
LG
53h
53h
4Ch
4Ch
RESET ALL
MEMORY CALL
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
HOLD
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
HORIZ. PIXELS
VERT. LINES
VERT. SYNC.
SHUTTER (U)
SHUTTER (L)
SHUTTER (LS)
SHUTTER (RS)
RSTALL
MMC
HP
VP
FN
TRK
CIN
HLD
HLB
HLE
CLP
CLW
HPL
VLN
VSC
SHU
SHL
SHLS
SHRS
52h 53h 54h
4Dh 4Dh
48h 50h
56h 50h
46h 4Eh
54h 52h
43h 49h
48h 4Ch
48h 4Ch
48h 4Ch
43h 4Ch
43h 4Ch
48h 50h
56h 4Ch
56h 53h
53h 48h
53h 48h
53h 48h
53h 48h
52h
4Dh
52h
59h
53h
54h
53h
49h
50h
50h
53h
42h
4Dh
4Dh
52h
50h
58h
4Dh
53h
52h
43h
44h
47h
47h
54h
47h
43h
41h
42h
42h
4Dh
54h
4Fh
4Fh
4Eh
46h
54h
VALUE
±30±30±30 (R from G+Main data+B from G)
±30±30±30 (R from G+Main data+B from G)
0 (OFF), 1 (ON)
1 (VIDEO), 2 (COMPUTER), 3 (USER), 4 (OFF)
±30±30±30 (R+G+B)
±30±30±30 (Y+C+M)
±05
±20
1 (STANDARD), 2 (HIGH), 3 (LOW), 4 (USER)
±10
±10
±10
0 (DYNAMIC), 1 (STANDARD), 2 (THEATER), 3 (AUTO)
0 (OFF), 1 (1), 2 (2), 3 (3)
0 (OFF), 1 (ON)
00 (OFF) , 05, 10, 15, 30, 60
0 (OFF), 1 (ON)
0 (BLACK), 1 (BLUE), 2 (LOGO)
0 (BLACK), 1 (LOGO)
0 (STANDARD), 1 (LOW)
0 (OFF), 1 (MIRROR), 2 (INVERT), 3 (MIRROR, INVERT)
0 (Upper left), 1 (Lower right)
1-4
1-5
0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
0 (OFF), 1 (ON)
0 (OFF), 1 (CENTER), 2 (UPPER), 3 (LOWER)
0 (OFF), 1 (ON)
0(
), 1 (English), 2 (Español), 3 (Deutsch) , 4 (Français),
5 (Italiano),6 (
), 7 (
), 8 (
), 9(
)
41h 4Ch 4Ch
43h
0 (AUTO), 1 (USER1), 2 (USER2)
+ (increase), – (decrease)
+ (increase), – (decrease)
00 - 39
4Bh
+ (increase), – (decrease)
4Eh
0 (RGB), 1 (YCBCR/YPBPR)
44h
0 (AUTO), 1 (ON), 2 (OFF)
42h
–01 - –99
45h
01 - 99
50h
00 - 63
57h
01 - 63
4Ch
0000 - 9999
4Eh
0000 - 9999
43h
0 (AUTO), 1 (ON), 2 (OFF)
55h
000 - 383 (000-299 : For SL25U)
4Ch
000 - 383 (000-299 : For SL25U)
4Ch 53h
000 - 510 (000-398 : For SL25U)
52h 53h
000 - 510 (000-398 : For SL25U)
*1) When sRGB is ON, only the main data are effective.
• Some commands are not executed depending on the input signal. The operational restrictions same as
those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.
4
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII
HEX
'+'
2Bh
[Example 1]
'–'
2Dh
'0'
30h
'1'
31h
'2'
32h
'3'
33h
'4'
34h
'5'
35h
'6'
36h
'7'
37h
'8'
38h
'9'
39h
When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks
are ASCII codes.):
Sending commands
from the PC, etc.
30 30 41 50 4F 4E 31 0D
'0' '0' 'A' 'P' 'O' 'N' '1' '
Status code from
Description
the projector
Command for setting the
'
30 30 41 50 4F 4E 31 0D
AUTO POWER ON to ON
Command receipt confirmation
'0' '0' 'A' 'P' 'O' 'N' '1' '
(Command echo back)
'
The data code of CONTRAST and BRIGHTNESS consists of the difference data between R and G, the main data, and
the difference data between B and G.
[Example 2]
When setting the difference data between R and G to +10, the main data to 0, and the difference
data between B and G to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code from
the projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '
Description
Command for setting the
picture control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '
Command receipt confirmation
(Command echo back)
[Example 3]
When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in
quotation marks are ASCII codes.)::
Sending commands
from the PC, etc.
30 30 53 0D
'0' '0' 'S' '
Status code from
Description
the projector
Command for checking
'
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' '
5
'
the TINT setting
Check result (+10)