Bosch Aquatak Clic 125 Operating instructions

OBJ_DOKU-13483-002.fm Page 1 Thursday, January 13, 2011 3:38 PM
WEU
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-garden.com
F 016 L70 546 (2011.01) O / 131 WEU
WEU
Aquatak Clic
125 | 130 | 135 | 140
de
en
fr
es
pt
it
nl
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης
tr Orijinal işletme talimat
OBJ_BUCH-764-002.book Page 3 Thursday, January 13, 2011 3:33 PM
|3
11
1
10
9
2
8
3
7
4
6
5
Aquatak
Aquatak
Aquatak
Aquatak
Bosch Power Tools
Clic
Clic
Clic
Clic
125
130
135
140
F 016 L70 546 | (13.1.11)
OBJ_BUCH-764-002.book Page 4 Thursday, January 13, 2011 3:33 PM
4|
A
B
1
13
8
7
12
12
C
D
13
13
14
13
E
F
8
7
F 016 L70 546 | (13.1.11)
Bosch Power Tools
OBJ_BUCH-764-002.book Page 5 Thursday, January 13, 2011 3:33 PM
|5
G
H
9 10
I
3
J
K
15
5
6
L
M
16
Bosch Power Tools
F 016 L70 546 | (13.1.11)
OBJ_BUCH-764-002.book Page 16 Thursday, January 13, 2011 3:33 PM
16 | English
Safety Notes
en
Before start-up please read these instructions!
Before using the machine please read
the operating instructions for your
unit and comply in particular with
these safety instructions. Please
keep the instructions safe for later
use.
f If an extension cord is used, the plug and
socket must be of watertight construction.
The extension cord must have a cross section
in accordance with the operating instructions and be protected against splashed water. The connection must not be in water.
f When replacing plugs on the power supply
cable or extension lead the spray water
guard and mechanical stability must remain
intact.
The warning and information signs attached to
the unit provide important information for safe
operation.
Water connection
Apart from the information in the operating instructions comply with the general safety regulations and regulations for the prevention of
accidents.
f All connecting hoses must have properly
sealed joints.
Never direct the water jet at people, animals, the unit or electric
components.
Power supply
f The voltage indicated on the rating plate
must correspond to the voltage of the power
source.
f We recommend that this equipment is only
connected into a socket which is protected
by a circuit-breaker that would be actuated
by a 30 mA residual current.
f If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to
avoid a hazard.
f Never touch the mains plug with wet hands.
f Do not pull plug while operating the device.
f Do not run over, crush or pull the power supply cable or extension lead, otherwise it may
be damaged. Protect the cable from heat, oil
and sharp edges.
f Do not use the appliance, if the power supply
cable or important parts, e. g. high-pressure
hose, trigger gun or safety devices are damaged.
f Comply with the regulations of your water
supply company.
f The appliance should never be used on the
drinking water supply without a back flow
valve. Water which has passed the back flow
valve is regarded as undrinkable.
f The high-pressure hose must not be damaged (danger of bursting). A damaged highpressure hose must be replaced immediately. Only use hoses and connections recommended by the manufacturer.
f High-pressure hoses, fittings and couplings
are important for the safety of the appliance.
Use only hoses, fittings and couplings recommended by the manufacturer.
Application
f Before use, check that the unit and operating
equipment are in perfect condition and are
safe to operate. Do not use the unit if it is not
in perfect condition.
f Do not direct the jet against yourself or others in order to clean clothes or footwear.
f Never draw in solvent-containing liquids, undiluted acids, acetone or solvents! This includes petrol, paint thinners, heating oil. The
sprayed vapour is highly flammable, explosive and toxic.
f Warning: Inadequate extension cords can be
dangerous.
F 016 L70 546 | (13.1.11)
Bosch Power Tools
OBJ_BUCH-764-002.book Page 17 Thursday, January 13, 2011 3:33 PM
English | 17
f The appropriate safety regulations must be
observed when using the unit in dangerous
areas (e.g. petrol stations). It is forbidden to
operate the unit in potentially explosive locations.
f The unit must be placed on a solid base.
f Only use detergents recommended by the
manufacturer and comply with the application, disposal and warning instructions of the
detergent manufacturers.
f All current-conducting components in the
working area must be protected against
splashed water.
f The gun trigger must not be jammed in position “ON” during operation.
f Wear suitable protective clothing to protect
against splashing from some parts. Do not
use the appliance within the range of persons unless they also wear protective clothing.
f Vehicle tyres/tyre valves may only be cleaned
from a minimum distance of 30 cm, otherwise the vehicle tyre/tyre valve could be
damaged by the high-pressure jet. The first
indication of this is a discoloration of the
tyre. Damaged vehicle tyres/tyre valves can
be extremely dangerous.
f The unit may only be used by authorised persons who have received training or have
demonstrated their ability to operate the
unit. The unit must not be operated by children or juveniles (danger of accidents due to
incorrect use of the unit). Children should be
supervised to ensure that they do not play
with the appliance.
f The unit is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the unit by a person responsible for their safety.
f The unit must never be left unsupervised
while the unit is switched on.
f The water jet from the high-pressure nozzle
produces a recoil on the gun. You should
therefore hold the gun and spray lance firmly
with both hands.
Transport
f Switch off the motor and secure the unit before transporting.
Maintenance
f Materials containing asbestos and other materials which contain substances which are
hazardous to your health must not be
sprayed.
f Switch off the unit prior to all cleaning and
maintenance work and before replacing components. Pull out the mains plug if the unit is
mains-operated.
f Detergents must not be used undiluted. The
products are safe to use as they contain no
acids, alkalis or substances which are detrimental to the environment. We recommend
that the detergents are kept out of the reach
of children. If detergent comes into contact
with the eyes, wash immediately with plenty
of water and if swallowed contact a doctor
immediately.
f Repairs may only be carried out by authorised Bosch Service Centres.
Accessories and spare parts
f Only use accessories and spare parts which
have been approved by Bosch. Original accessories and spare parts guarantee that the
unit can be operated safely and without any
breakdowns.
Operation
f The operator must use the unit in accordance
with the regulations. He/she must take local
conditions into account and be aware of other people, especially children, when operating the unit.
Bosch Power Tools
F 016 L70 546 | (13.1.11)
OBJ_BUCH-764-002.book Page 18 Thursday, January 13, 2011 3:33 PM
18 | English
Product Description and Specifications
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Intended Use
The product is intended for cleaning areas and
objects outside the house, tools, vehicles and
boats, if the appropriate accessories such as
cleaning agents approved by Bosch are used.
Intended use is related to operation within 0°C
and 40°C ambient temperature.
This product should not be used for professional use.
Product Features
The numbering of the components shown refers
to the representation of the pressure washer on
the graphic pages.
1 Handle
2 Detergent tank
3 High pressure hose
4 Main switch
5 Inlet Connector
6 Supply cable
7 4 Jet-lance
8 Power gun
9 Trigger
10 Trigger safety lock
11 Serial number
12 Screws for handle assembly
13 Screws for holder assembly
Delivery Scope
14 Clip to secure the high pressure hose
Carefully remove the pressure washer from its
packaging and check that you have all the following items:
15 Water inlet connection
–
–
–
–
–
–
–
–
–
–
Power washer
Power gun
4 Jet-lance
Flexi-jet-lance (Aquatak Clic 135,
Aquatak Clic 140)
Inlet Connector
Detergent tank with cap
Handle
4 x Accessory holders
Hardware pack incl. screws
Operating instructions
16 Strainer
Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our accessories program.
When parts are missing or damaged, please contact your dealer.
F 016 L70 546 | (13.1.11)
Bosch Power Tools
OBJ_BUCH-764-002.book Page 19 Thursday, January 13, 2011 3:33 PM
English | 19
Technical Data
Power washer
Aquatak
Clic 125
Aquatak
Clic 130
Aquatak
Clic 135
Aquatak
Clic 140
3 600 H79 0.. 3 600 H79 1.. 3 600 H79 2.. 3 600 H79 3..
Article number
Rated power
Supply Temperature max.
W
1800
2000
2100
2300
°C
60
60
60
60
Supply rate min.
l/min
9
9
9
9
Supply pressure max.
MPa*
0 – 0.6
0 – 0.6
0 – 0.6
0 – 0.6
Working pressure
MPa*
9
9.5
10
10.5
Max. pressure
MPa*
12.5
13
13.5
14
Flow rate
l/min
6.8
7.2
7.5
7.8
–
–
z
z
m
6
9
9
12
l
1
1
1
1
kg
16.9
17.5
24.3
24.9
/II
/II
/I
/I
Flexi-jet-Lance
High pressure hose
Detergent tank capacity
Weight according to
EPTA-Procedure 01/2003
Protection class
Serial number
See serial number 11 (rating plate) on pressure washer.
*0.6 MPa=6 bar/9 MPa=90 bar/9.5 MPa=95 bar/10 MPa=100 bar/10.5 MPa=105 bar/12.5 MPa=125 bar/
13 MPa=130 bar/13.5 MPa=135 bar/14 MPa=140 bar
Noise/Vibration Information
Measured sound values determined according
to 2000/14/EC (1.60 m height, 1 m distance
away).
Typically the A-weighted noise levels of the
product are: Sound pressure level 80 dB(A);
sound power level 87 dB(A). Uncertainty
K =3 dB.
Vibration total values (triax vector sum) determined according to EN 60335:
Vibration emission value ah =3 m/s2,
Uncertainty K =1 m/s2.
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical data” is
in conformity with the following standards or
standardization documents: EN 60335 according to the provisions of the directives
2004/108/EC, 2006/42/EC, 2000/14/EC.
Bosch Power Tools
2000/14/EC: Guaranteed sound power level
90 dB(A). Conformity assessment procedure
according to Annex V.
Equipment category: 27
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
30.11.2010
F 016 L70 546 | (13.1.11)
OBJ_BUCH-764-002.book Page 20 Thursday, January 13, 2011 3:33 PM
20 | English
Assembly
For Your Safety
f Warning! Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
Aquatak Clic 125/Aquatak Clic 130
Your pressure washer is double insulated for
safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU
countries 220 V, 240 V as applicable). Only use
approved extension cables. Contact your Bosch
Service Centre for details.
Aquatak Clic 135/Aquatak Clic 140
Your pressure washer requires an earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable). Only use approved extension cables. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your high pressure washer, only the following cable dimensions should be used:
- 1.5 mm2 – max length 20 m
- 2.5 mm2 – max length 50 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the
earth cable of your supply network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the
nearest Bosch Service Centre.
f WARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight construction and intended for outdoor use.
Cable connections should be kept dry and off
the ground.
It is recommended for increased electrical safety to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Always check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch Service Centre.
F 016 L70 546 | (13.1.11)
Products sold in GB only: Your product is fitted
with an BS 1363/A approved electric plug with
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a residual current device (RCD) with a rated residual
current of 30 mA or less.
Assembly
Assembly of Product (see figure A)
Fix the top handle 1 to the pressure washer using screws 12.
Fix the holder to the pressure washer using
screws 13.
Slide detergent tank into position as shown.
Connecting high pressure gun to lance
(see figures B and E)
Insert the 4 jet-lance 7 into power gun 8. Depress and turn the jet-lance 90° clockwise to
lock in place.
Connecting high pressure hose to gun
(see figures C–D)
Join high pressure hose to gun as shown.
Secure with clip 14 as shown, check if secure by
pulling on high pressure hose.
Water connection (see figures H and J)
Screw inlet connector 5 onto machine water inlet connection 15.
Attach water supply hose (not supplied) to the
mains water supply and machine.
High pressure hose/Supply cable
(see figures I and K)
Pull out the pressure hose 3 and supply cable 6
of the pressure washer.
Bosch Power Tools
OBJ_BUCH-764-002.book Page 21 Thursday, January 13, 2011 3:33 PM
English | 21
20 mm
20 mm
To store pressure hose 3 or
supply cable
6, pull the
hose or cable
briefly (the
hose or cable
rolls up automatically).
Note: Always pull out the pressure hose and
supply cable completely when using the pressure washer.
Adjusting 4 Jet-lance (see figure F)
The 4 jet-lance has 4 different modes, which can
be selected by rotating the nozzle.
Give the detergent time to work, but never leave
it to dry.
Rinse from top and work downwards.
Flexi-jet-lance (depending on model)
(see figures B and E)
Turn the 4 jet-lance 7 90° anti-clockwise. Extract the 4 jet-lance.
Insert the flexi-jet-lance into the power gun 8.
Depress and turn the flexi-jet-lance 90° clockwise to lock in place.
Operation
Starting and Stopping (see figure G)
Before starting ensure product is in
horizontal position.
Low pressure fan jet – for application
of detergents.
High pressure fan jet – for cleaning
sensitive surfaces like cars, garden furniture etc.
Roto jet – for powerful cleaning of
larger areas like patios, driveways, etc.
Never use the roto jet mode to clean
motor vehicles.
Pencil jet – for cleaning with maximum power in smaller areas e. g. barbecues, chewing gum on patio etc.
Suitable for extremely dirty surfaces.
Operating with Detergents
f Only use Bosch approved detergents. Unsuitable detergents may damage the unit
and the object being cleaned.
Fill the detergent tank 2 with diluted detergent,
as recommended.
To spray detergent rotate the nozzle of the
4 Jet-lance to low pressure fan jet mode.
Read the detergent label for additional instructions.
Starting
Connect the product to the mains supply ensuring that the mains switch is in the off position.
Attach water supply hose (not supplied) to the
mains water supply and machine.
Open water tap.
Press the safety lock 10 to release the trigger 9.
Fully press the trigger 9 until there is a constant
flow of water to clear the air from the machine
and water supply hose. Release trigger 9. Press
the trigger safety lock 10.
Press on/off switch 4.
Point the power gun 8 downwards. Press the
trigger safety lock 10 to release the trigger 9.
Fully press the trigger 9.
Always wet the object first.
Apply detergent to the object from the bottom
up.
Bosch Power Tools
F 016 L70 546 | (13.1.11)
OBJ_BUCH-764-002.book Page 22 Thursday, January 13, 2011 3:33 PM
22 | English
Autostop function
Self priming function
The machine is designed to switch off the motor
when the trigger 9 is released on the gun. This
feature relieves high pressure from the system
to achieve a longer lifetime and lower energy
consumption. (A short squeaking noise can occur and is completely normal.)
The machine can also operate with water from
sources other than a water tap, e. g. ponds and
water butts due to the self priming function. The
use of an additional water filter (not supplied)
is highly recommended for this kind of use.
Stopping
Release trigger 9. Press the trigger safety lock
10. The power gun is now locked and can not be
operated accidentally.
Press on/off switch 4.
Close water tap. Unplug the machine from the
mains supply.
Make sure the water source is situated no more
than 1 m below the level of the machine.
Fill water supply hose (not supplied) with water
before connecting it to the machine. Running
the machine without water (running dry) will
damage it.
Run machine without lance attached until there
is a constant flow of water.
Turn off machine and connect lance.
Press the trigger safety lock 10 to release the
trigger 9. Fully press the trigger 9 until there is
no more water pressure in the machine. Release
trigger 9. Press the trigger safety lock 10.
Working Advice
Disconnect water supply hose from machine
and water supply.
Ensure that the pressure washer is on level
ground.
General
Do not kink or drive a motor vehicle over the
high pressure hose. Do not expose the high
pressure hose to sharp edges or corners.
Never use the roto jet mode to clean motor vehicles.
Troubleshooting
The following chart lists problem symptoms, possible causes and corrective action, if your pressure
washer does not operate properly. If these do not identify and correct the problem, contact your
service agent.
f Warning: Switch off and remove plug from mains before investigating fault.
Problem
Possible Cause
Corrective Action
Motor refuses to start
Plug not connected
Connect plug
Mains socket faulty
Use another socket
Fuse faulty/blown
Replace fuse
Extension cable damaged
Try without extension cable
Fuse faulty/blown
Replace fuse
Wrong mains voltage
Check that mains voltage corresponds to specifications on the
model tag
Motor stops
F 016 L70 546 | (13.1.11)
Bosch Power Tools
OBJ_BUCH-764-002.book Page 23 Thursday, January 13, 2011 3:33 PM
English | 23
Problem
Possible Cause
Corrective Action
Fuses blow
Fuses incorrectly rated
Change to a mains supply higher than the pressure washer
amp consumption
Excessive working pressure
Nozzle partly blocked
Clean nozzle (see figure L)
Pressure pulsating
Air in the inlet water supply
hose/pump
Allow pressure washer to run
with open spray handle and
nozzle at low pressure until regular working pressure is obtained
Inadequate water supply
Check that the water supply
corresponds to specifications.
The minimum specification for
the water supply hose is 1/2" or
13 mm diameter
Water strainer blocked
Clean water strainer
Water supply hoses squeezed
Straighten out kinked water
supply hoses
Nozzle worn
Change the nozzle
Start/stop valve worn
Activate trigger five times in
quick succession
Pressure too low, but steady
Motor starts up but no working
pressure
No water supply
Connect water supply
Water strainer clogged up
Clean the water strainer
The pressure washer starts irregularly by itself
Pump/power gun leaky
Contact your Bosch Service
Centre
Water leaks from machine
Leaking pump
6 drops per minute are permissible. In case of more serious
leakage, you should contact
your Bosch Service Centre
Maintenance and Service
Maintenance
f Stop, remove plug from the power supply
and disconnect from water supply.
Note: To ensure long and reliable service, carry
out the following maintenance regularly.
Regularly check for obvious defects such as
loose fixings, and worn or damaged components.
Bosch Power Tools
Check that covers and guards are undamaged
and correctly fitted. Carry out necessary maintenance or repairs before using.
If the machine should happen to fail despite the
care taken in manufacture and testing, repair
should be carried out by an authorised customer service agent for Bosch garden products.
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the machine.
F 016 L70 546 | (13.1.11)
OBJ_BUCH-764-002.book Page 24 Thursday, January 13, 2011 3:33 PM
24 | English
Cleaning/inspecting the strainer
(see figure M)
Expose the strainer 16 in the machine water inlet connection by removing the inlet connector
5.
The strainer 16 can be easily removed with long
nose pliers. Rinse and replace. If damaged replace.
Never use the pressure washer without the
strainer or a damaged strainer.
After use/Storage
Clean the exterior of the machine thoroughly using a soft brush or cloth. Do not use water, solvents or polishes. Remove all debris, especially
from the ventilation slots.
Frost will damage a pressure washer that has
not been completely emptied of water. To prepare machine for longer storage in cold conditions, run without connecting to water supply
for no more than 30 seconds. The machine
should be stored in a frost free room.
Do not place other objects on top of the machine.
Ensure cables are not trapped when storing. Do
not kink high pressure hose.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-garden.com
Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories.
F 016 L70 546 | (13.1.11)
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail: bsctools@icon.co.za
Bosch Power Tools
OBJ_BUCH-764-002.book Page 25 Thursday, January 13, 2011 3:33 PM
English | 25
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
E-Mail: rbsa-hq.pts@za.bosch.com
Disposal
The pressure washer, accessories and packaging should be sorted for environmental-friendly
recycling.
Do not dispose of pressure washers into household waste!
Only for EC countries:
According to the European directive 2002/96/EC for Waste Electrical and Electronic Equipment and
its implementation into national
law, electrical and electronic
equipment that are no longer usable must be collected separately and disposed
of in an environmentally correct manner.
Subject to change without notice.
Environmental Protection
Chemicals dangerous to the environment must
not be allowed to enter the ground, ground water or ponds, streams, etc.
For the use of cleaning agents, observe the instructions on the package and the prescribed
concentration exactly.
For the cleaning of motor vehicles the local regulations should be observed: Do not allow oil
sprayed off to enter into the ground water. Recycle raw materials instead of waste disposal.
Bosch Power Tools
F 016 L70 546 | (13.1.11)