CB

OPERATOR’S MANUAL

98012620-1

LISTED

®

MODEL #

CB-301007D

CB-402007A

CB-402007B

CB-402007C

CB-402007H

ORDER #

1.106-551.0

1.106-552.0

1.106-553.0

1.106-554.0

1.106-555.0

MODEL #

CB-353007A

CB-353007B

CB-353007C

CB-353007G

CB-353007H

ORDER #

1.106-556.0

1.106-557.0

1.106-558.0

1.106-559.0

1.106-560.0

To locate your local Shark Commercial Pressure Washer Dealer nearest you, visit www.Sharkpw.com

9.801-262.0

Important Safety Information

Component Identification

Assembly Instructions

Operating Instructions

Applying Detergent & General Operating Techniques

Shut Down & Clean-Up

9

10

Storage 10

Troubleshooting 11

7

8

4-5

6

Preventative Maintenance

Oil Change Record

Hose & Spray Gun Assembly & Parts List

Exploded View

Exploded View Parts List

VB8 Valve Exploded View and Parts List

Pump Exploded View and Parts List

Specifications Page

Multi-Room Installation Guide

KD Pump Exploded View and Parts List

KM Series Pump Exploded View and Parts List

VRT 3 Unloader Exploded View and Parts List

Warranty

12

12

13

14-15

16-17

18

19

20-21

22

23-24

25-26

27

CONTENTS

Model Number _____________________________

Serial Number ______________________________

Date of Purchase ___________________________

The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference.

9.801-262.0 • Shark CB • Rev. 5/13

3

4

INTRODUCTION & ImpORTaNT SafeTy INfORmaTION

Thank you for purchasing a Shark Pressure Washer.

We reserve the right to make changes at any time without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood.

If the operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents.

Owner and/or user must study and maintain for future reference the manufacturers’ instructions.

The operator must know how to stop the machine quickly and understand the operation of all controls.

Never permit anyone to operate the engine without proper instructions.

Save TheSe INSTRUCTIONS

This manual should be considered a permanent part of the machine and should remain with it if machine is resold.

When ordering parts, please specify model and serial number. Use only identical replacement parts.

This machine is to be used only by trained operators.

ImpORTaNT SafeTy

INfORmaTION

WARNING: To reduce the risk of injury, read operating instructions carefully before using.

1. Read the owner's manual thoroughly. Failure to follow instructions could cause malfunction of the machine

ReaD OpeRaTOR’S maNUal ThOROUghly pRIOR TO USe.

and result in death, serious bodily injury and/or property damage.

2. Know how to stop the machine and bleed pressure quickly. Be thoroughly familiar with the controls.

3. Stay alert — watch what you are doing.

4. All installations must comply with local codes.

Contact your electrician, plumber, utility company or the selling distributor for specific details. If your machine is rated 250 volts or less, single phase will be provided with a ground fault circuit interrupter (GFCI). If rated more than 250 volts, or more than single phase this product should only be connected to a power supply receptacle protected by a GFCI.

DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product

- if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adaptor with this product

WARNING

WARNING: Keep wand, hose, and water spray away from electric wiring or fatal electric shock may result.

keep WaTeR

SpRay aWay fROm eleCTRICal WIRINg.

5. To protect the operator from electrical shock, the machine must be electrically grounded.

It is the responsibility of the owner to connect this machine to a UL grounded receptacle of proper voltage and amperage ratings. Do not spray water on or near electrical components. Do not touch machine with wet hands or while standing in water. Always disconnect power before servicing.

WARNING

WARNING: Flammable liquids can create fumes which can ignite, causing property damage or severe injury.

RISk Of explOSION:

DO NOT SpRay flammable lIqUIDS.

WARNING: Risk of explosion —

Do not spray flammable liquids.

6. Do not allow acids, caustic or abrasive fluids to pass through the pump.

7. Never run pump dry or leave spray gun closed longer than 1-2 minutes.

8. Keep operating area clear of all persons.

WARNING

USe pROTeCTIve eye WeaR aND ClOThINg

WheN OpeRaTINg

ThIS eqUIpmeNT.

WARNING: High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds. To avoid personal injury, eye, hand and foot safety devices must be worn.

9. Eye, hand, and foot protection must be worn when using this equipment.

9.801-262.0 • Shark CB • Rev. 5/13

ImpORTaNT SafeTy INfORmaTION

WARNING

WARNING: Grip cleaning wand securely with both hands before starting. Failure to do this could result in injury from a whipping wand.

WARNING

RISk Of INjURy fROm fallS WheN

USINg laDDeR.

WARNING: Be extremely careful when using a ladder, scaffolding or any other relatively unstable location. The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces.

TRIggeR gUN kICkS baCk - hOlD WITh bOTh haNDS

WARNING

RISk Of INjeCTION

OR SeveRe INjURy

TO peRSONS. keep

CleaR Of NOzzle.

WARNING: High pressure developed by these machines will cause personal injury or equipment damage. Keep clear of nozzle. Use caution when operating. Do not direct discharge stream at people, or severe injury or death will result.

10. To reduce the risk of injury, close supervision is necessary when a machine is used near children.

Do not allow children to operate the pressure washer. This machine must be attended during operation.

11. Never make adjustments on machine while in operation.

12. Be certain all quick coupler fittings are secured before using pressure washer.

WARNING

WARNING: Protect machine from freezing.

13. To keep machine in best operating conditions, it is important you protect machine from freezing. Failure to protect pROTeCT fROm fReezINg machine from freezing could cause malfunction of the machine and result in death, serious bodily injury, and/or property damage.

Follow storage instructions specified in this manual.

14. Inlet water must be clean fresh water and no hotter then 185°F.

15. Manufacturer will not be liable for any changes made to our standard machines or any components not purchased from us.

16. The best insurance against an accident is precaution and knowledge of the machine.

17. Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

18. Do not operate this machine when fatigued or under the influence of alcohol, prescription medications, or drugs.

Follow the maintenance instructions specified in the manual.

5

9.801-262.0 • Shark CB • Rev. 5/13

6

COmpONeNT IDeNTIfICaTION

high pressure

Nozzle

Soap Nozzle

Water

Supply quick

Coupler

On/Off

Switch garden hose Inlet garden hose

(not included) high pressure hose hose

Coupler

Detergent

Injector

Detergent pick-up Tube

Discharge

Nipple

98012620-2

Wand

Trigger

Spray gun

Swivel

Connector

Detergent bucket

(not included)

Detergent Injector - Allows you to siphon and mix detergents, when used with soap nozzle.

high pressure hose — Connect one end to water pump discharge nipple and the other end to spray gun.

Spray gun — Controls the application of water and detergent onto cleaning surface with trigger device.

Includes safety latch.

Wand — Must be connected to the spray gun.

Swivel Connector - Allows free range of movement to avoid coiling hoses.

NOTe: If trigger on spray gun is released for more than 2 minutes, water will leak from pump protector valve. Warm water will discharge onto floor and cool water will allow the pump protector to seal.

This system prevents internal pump damage.

9.801-262.0 • Shark CB • Rev. 5/13

aSSembly INSTRUCTIONS

Spray gun

Nozzle

Safety latch

Coupler high pressure hose

98012620-4

98012620-5

98012620-3

STep 1: Attach the high pressure hose to the spray gun using teflon tape on hose threads. Use safety latch to prevent from opening.

STep 2: Connect garden hose to the cold water source. Before installing nozzle, turn on water supply and run machine, allowing water to flush through the system until clear.

STep 3: Insert nozzle into coupler.

Release the coupler collar and push the nozzle until the collar clicks. Pull the nozzle to make sure it is seated properly.

Inlet fitting

Outlet fitting

98012620-6

STep 4: Connect the high pressure hose to the outlet discharge fitting. Push coupler collar forward until secure.

Connect the garden hose to pump water inlet. Inspect inlets. CAUTION: Do not run the pump without water or pump damage will result.

9.801-262.0 • Shark CB • Rev. 5/13

7

OpeRaTINg INSTRUCTIONS

Cold

Water

Source

98012620-7 garden hose

98012620-8 98012620-9

STep 1: Connect garden hose to the cold water source and turn water on completely. Never use hot water.

STep 2: Trigger the spray gun to eliminate trapped air then wait for a steady flow of water to emerge from the spray wand. Then install nozzle.

STep 3: Connect to appropriate power supply. Push GFCI reset button.

On/Off

Switch

Safety latch

98012620-11

98012620-10

STep 4: Turn machine on by pushing switch at front of machine.

WARNING! Never replace nozzles without engaging the safety latch on the spray gun trigger.

NOzzleS

8

98012620-12

The five color-coded quick connect nozzles provide a wide array of spray widths from 0° to 40° and are easily accessible when placed in the convenient rubber nozzle holder, which is provided on the front of the machine.

NOTe: For a more gentle rinse, select the white 40° or green 25° nozzle.

To scour the surface, select the yellow 15° or red 0° nozzle. To apply detergent select the black nozzle.

9.801-262.0 • Shark CB • Rev. 5/13

DeTeRgeNTS aND geNeRal OpeRaTINg TeChNIqUeS

WARNING

WARNING: Some detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury.

TheRmal pUmp pROTeCTION

If you run your pressure washer for 2 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach high temperatures. When the water reaches this temperature, the pump protector engages and cools the pump by discharging the warm water onto the ground. This thermal device prevents internal damage to the pump.

98012620-13

STep 1: Use detergent designed specifically for pressure washers. Household detergents could damage the pump. Prepare detergent solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the filter end of detergent suction tube into the detergent container.

CleaNINg TIpS

Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and apply to surface at low pressure (for best results, limit your work area to sections approximately 6’ square and always apply detergent from bottom to top). Allow detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. If surface appears to be drying, simply wet down surface with fresh water.

If needed, use brush to remove stubborn dirt. Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 1' from cleaning surface. Use overlapping strokes as you clean and rinse any surface. For best surface cleaning action spray at a slight angle.

98012620-14

STep 2: Apply safety latch to spray gun trigger. Secure black detergent nozzle into quick coupler. NOTe: Detergent cannot be applied using the Yellow nozzle.

98012620-15

STep 3: With the motor running, pull trigger to operate machine. Liquid detergent is drawn into the machine and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface.

IMPORTANT: You must flush the detergent injection system after each use by placing the suction tube into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Recommendations:

• Before cleaning any surface, an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results.

• If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface.

• Keep the spray nozzle a safe distance from the surface you plan to clean. High pressure wash a small area, then check the surface for damage. If no damage is found, continue to pressure washing.

CAUTION - Never use:

• Bleach, chlorine or other corrosive chemicals

• Liquids containing solvents (i.e., paint thinner, gasoline, oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the machine and will damage the surface being cleaned.

RINSINg

It will take a few seconds for the detergent to clear.

Apply safety latch to spray gun. Remove black soap nozzle from the quick coupler. Select and install the desired high pressure nozzle. NOTe: You can also stop detergent from flowing by simply removing detergent siphon tube from bottle.

9.801-262.0 • Shark CB • Rev. 5/13

9

ShUTTINg DOWN aND CleaN-Up

98012620-16

98012620-17

STep 1: Remove detergent suction tube from soap container and insert into one gallon of fresh water. Use black soap nozzle with detergent injector. Pull trigger on spray gun and siphon water for one minute.

STep 2: Turn off machine by pushing switch on front panel.

98012620-18

98012620-19

STep 3: Turn off water supply.

STep 4: Press trigger to release water pressure.

10 pump

Water

Inlet high pressure

Outlet

Safety latch

98012620-20

98012620-21

STep 5: Disconnect the garden hose from the water inlet on the machine.

Protect from freezing.

STep 6: Disconnect the high pressure hose from high pressure outlet.

98012620-22

STep 7: Engage the spray gun safety lock.

STORage pump Storage

CAUTION

CAUTION: Always store your pressure washer in a location where the temperature will not fall below 32° F

(0° C). The pump in this machine is susceptible to permanent damage if frozen.

FREEzE DAMAGE IS NOT COvERED BY WARRANTY.

If you must store your pressure washer in a location where the temperature is below 32° F, you can minimize the chance of damage to your machine by draining your machine as follows:

1. Stop the pressure washer and detach supply hose and high pressure hose. Squeeze the trigger of the spray gun to drain all water from the wand and hose.

2. Restart pressure washer and let it run briefly (about

5 seconds) until water no longer discharges from the high pressure outlet.

9.801-262.0 • Shark CB • Rev. 5/13

pROblem pUmp RUNNINg

NORmally bUT pReSSURe lOW

ON INSTallaTION flUCTUaTINg pReSSURe pReSSURe lOW afTeR peRIOD

Of NORmal USe pUmp

NOISy pReSeNCe

Of WaTeR

IN pUmp OIl

WaTeR DRIppINg fROm UNDeR pUmp

OIl DRIppINg fROm pUmp exCeSSIve vIbRaTION IN hIgh pReSSURe hOSe mOTOR WIll

NOT RUN

TROUbleShOOTINg

pOSSIble CaUSe

Pump sucking air

Check valves sticking

Unloader valve seat faulty

Nozzle incorrectly sized

Worn piston packing

Valves worn

Blockage in valve

Pump sucking air

Worn piston packing

Insufficient water

Nozzle worn

Suction or delivery valves worn

Suction or delivery valves blocked

Unloader valve seat worn

Unloader adjusted improperly

Worn piston packing

Bypass valve within unloader is obstructed or leaking

Air in suction line

SOlUTION

Check water supply and possibility of air.

Check and clean or replace if necessary.

Check and replace if necessary.

Check and replace if necessary.

Check and replace if necessary.

Check and replace if necessary.

Check and clean if necessary.

Check water supply connections.

Check and replace if necessary.

Check filter and hose for breakage.

Check and replace if necessary.

Check and replace if necessary.

Check and clean if necessary.

Check and replace if necessary.

Call local Landa dealer. Tampering with the factory setting may cause personal injury and/or property damage and will void the manufacturer's warranty.

Check and replace if necessary.

Remove and clean bypass cartridge.

Check water supply and connections on suction line.

Check and replace if necessary.

Broken or weak suction or delivery valve spring

Foreign matter in valves

Worn bearings

Excessive temperature of water

Oil seal worn

High humidity in air

Piston packing worn

Piston packing worn

O-Ring plunger retainer worn

Oil seal worn

Irregular functioning of the pump valves

Obstruction in filter

Motor overload

Step down transformer fuses

Coil of magnetic starter defective maChINe WIll

NOT TURN ON WheN

SWITCh IS pUSheD

Timer is defective

Check and clean if necessary.

Check and clean if necessary.

Reduce to below 140°F.

Check and replace if necessary.

Check and change oil twice as often.

Check and replace if necessary.

Check and replace if necessary.

Check and replace if necessary.

Check and replace if necessary.

Check and replace if necessary.

Clean inlet filter.

Push in the overload button located on the motor (single phase) or the overload button on the magnetic start switch (three phase).

Check fuses and voltage. Replace if necessary.

Replace coil after the timer and unloader switch have been tested.

Join wires 15 and 16 together on timer. If machine works, replace timer.

9.801-262.0 • Shark CB • Rev. 5/13

11

pReveNTaTIve maINTeNaNCe pReveNTaTIve maINTeNaNCe

This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner, have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedure will assist in preserving the performance of your equipment. Contact your dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform maintenance more often under severe conditions.

pump Oil

Check valve Clearance

Water filter maINTeNaNCe SCheDUle

Inspect

Change

Inspect

Clean

25 Hours or Weekly

Yearly

Yearly

Every 6 Hours or Daily

Yearly

OIl ChaNge ReCORD

Check pump oil level before first use. Change pump oil after first 50 hours and every month or 500 hours thereafter.

Use SAE 30 weight oil.

Date Oil Changed month/Day/year estimated Operating hours Since last

Oil Change

Date Oil Changed month/Day/year estimated Operating hours Since last

Oil Change

12

9.801-262.0 • Shark CB • Rev. 5/13

5

6

8

hOSe & SpRay gUN aSSembly

4

1

7

10

3

9

98012620-23

11

2

hOSe & SpRay gUN aSSembly paRTS lIST

ITem paRT NO. DeSCRIpTION

1 9.802-166.0 Coupler, 3/8" Female

9.802-100.0 Quick Coupler O-Ring

2 8.739-125.0 Hose, 3/8" x 50',

1 Wire,Tuff-Flex

3 8.701-384.0 Gun, ST-1500, 5000

10.4 GPM

4 9.802-219.0 Wand w/Side Grip

5 8.712-398.0 Nozzle, Soap, Brass

6 Nozzle, See Exploded View Parts List

7 9.802-216.0 Injector, Detergent Adj.,

3-5 GPM 0.083

8 9.802-164.0 Coupler, 1/4" Female

9.802-096.0 Quick Coupler O-Ring

9 9.802-251.0 Tube, 1/4" x 1/2"

Clear Vinyl

10 6.390-126.0 Clamp, Hose

11 8.707-057.0 Strainer qTy

1

1

1

1

1

1

1

1

1

6 ft.

2

1

9.801-262.0 • Shark CB • Rev. 5/13

13

14

explODeD vIeW

76

7

20

74

63

63 64 enlarged

Reverse view

78

62

9

10

13

71

Time Delay

Option 75 auto Start

Option

77

64

64

63

5

7 auto Start

Option

77

64 70

13

64

76

9

75

62

61

6

4

21

58

22

12

25 80

23

54

58

61

74

22

12

25

62

71

66

51

19

58

1

2 for

3

Detail See pump assy.

82

11

38

24

98012620-24

15

8

14

23

9.801-262.0 • Shark CB • Rev. 5/13

explODeD vIeW

27

79

17 42

73

44

40

16

41

43

68

50

28

45

26

46

50

29

53

32

46

37

31

33

65

35

39

67

36

34

78

81

80

52

18

60

59

19

48

59

55

69

72

57

56

30

47

49

98012020-25

50

9.801-262.0 • Shark CB • Rev. 5/13

15

16

ITem paRT NO. DeSCRIpTION

1 Unloader, See Specifications Pages qTy

2 Pump, See Specifications Pages

3 Motor, See Specifications Pages

4 9.802-551.0 Transformer (552.0, 553.0

554.0, 556.0, 557.0, 558.0)

9.804-556.0 Transformer (555.0, 559.0,

560.0)

5 8.933-007.0 Fuse, ATMR, 1 Amp, 600V

(552.0, 553.0, 550.0, 556.0,

557.0, 559.0, 560.0)

9.802-462.0 Fuse, 1/2 Amp, 600V

(554.0, 558.0)

6 9.802-463.0 Fuse, Paper, Buss FNM-1/2,

250V Midget

7 Contactor, See Specification Pages

1

1

2

2

1

8 9.802-151.0 Swivel, 1/2" JIC Fem,

Push-On 2

9 9.802-457.0 Din Rail, 35 mm 4"

10 9.802-476.0 Box, Plastic, 10" x 8" x 6" w/Lid 1

9.802-475.0 Box, Plastic 8" x 8" x 4" (551.0) 1

11 9.803-038.0 Bracket, Electric Box Support 1

12 9.802-515.0 Strain Relief, STRT, LQ Tite 1/2"

(551.0) 1

9.802-524.0 Locknut, 1/2" Conduit

(551.0)

9.802-518.0 Strain Relief, STRT,

LQ Tite 3/4"

1

1

9.802-526.0 Lock Nut, 3/4" 1

13 9.802-515.0 Strain Relief, STRT, LQ Tite 1/2"1

9.802-524.0 Locknut, 1/2" Conduit 1

14 8.918-423.0 Hose, 3/8" x 22", 2 Wire, Pressure

Loop 1

15 9.802-259.0 Hose, 1/2" Push-On

16 9.802-776.0 Nut, 5/16" ESNA

1 ft.

4

17 9.803-100.0 Slider, Pump

18 9.802-738.0 Bolt, 1/2" x 8"

19 8.718-980.0 Washer, 5/16", Flat, SAE(551.0) 4

1

1

9.802-807.0 Washer, 3/8" SAE, Flat

(552.0-560.0)

20 Overload, See Specifications Pages

21 9.803-032.0 Standoff, Electrical Box

(552.0-560.0)

4

1

22 9.802-518.0 Strain Relief, 3/4" Strt, LQ Tite

(551.0, 552.0, 553.0, 554.0,

557.0, 558.0, 560.0) 1

9.802-526.0 Lock-Nut, 3/4"

9.802-521.0 Strain Relief, 3/4"

(556.0, 559.0)

23 8.932-969.0 Label, Warn Service Cord

1

1

1

24 9.802-039.0 Elbow, 1/2" JIC x 3/8", 90° 1

explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION qTy

25 9.802-436.0 Cord, Serv, SEO, 10/3

Coleman, Motor (552.0)

9.802-437.0 Cord Service, 10/4,

Motor (560.0)

9.802-428.0 Cord, Service, 12/3,

Motor (551.0)

9.802-425.0 Cord, Service, 8/3,

3.33 ft.

3.33 ft.

4.25 ft.

Motor (556.0, 559.0) 3.33 ft.

9.802-429.0 Cord Service, 12/4, Motor (553.0,

554.0, 555.0, 557.0, 558.0) 3.33 ft.

26 9.800-016.0 Label, Disconnect

Power Supply

27 9.802-879.0 Cover, Cabinet,

Cold Water, Black

1

1

28 9.802-875.0 Base Cabinet, Cold Water,

Wrinkle Black

29 9.802-451.0 Switch, Rocker, Carling w/Green Lens

1

1

9.802-452.0 Switch, Rocker, Carling Red

(Time-Delay Shutdown Option) 1

30 9.802-066.0 Pad, Soft Rubber, Duro 50 4

31 9.802-064.0 Grommet, Rubber

(Nozzle Holder)

32 9.802-146.0 Swivel, 1/2" MP x 3/4"

GHF w/Strainer

5

1

33 8.707-000.0 Connector, 1/2" Anchor

34 8.706-998.0 Connector, 3/8" Anchor

1

1

35 9.802-225.0 Downstream Injector

Assembly, Non-Adj.

36 9.802-171.0 Nipple, 3/8" x 3/8"

NPT ST Male

1

1

37 8.712-361.0 Nozzle, 0006, Red

(552.0-555.0)

8.712-362.0 Nozzle, 1506, Yellow

(552.0-555.0)

8.712-363.0 Nozzle, 2506, Green

(552.0-555.0)

8.712-364.0 Nozzle, 4006, White

(552.0-555.0)

8.712-345.0 Nozzle, 0004, Red

(556.0-560.0)

1

1

1

1

1

8.712-346.0 Nozzle, 1504, Yellow

(556.0-560.0)

8.712-347.0 Nozzle, 2504, Green

(556.0-560.0)

1

8.712-348.0 Nozzle, 4004, White

(556.0-560.0)

8.712-357.0 Nozzle, 0005.5, Red (551.0) 1

8.712-358.0 Nozzle, 1505.5, Yellow (551.0) 1

1

1

8.712-359.0 Nozzle, 2505.5, Green (551.0) 1

8.712-360.0 Nozzle, 4005.5, White (551.0) 1

38 8.718-858.0 Washer, 1/4" Flat Rubber Back,

SS 4

9.801-262.0 • Shark CB • Rev. 5/13

explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION

39 9.800-064.0 Label qTy

1

40 Bushing, See Specifications Pages

41 Bushing, See Specifications Pages

42 Pump Pulley, See Specifications Pages

43 Motor Pulley, See Specifications Pages

44 Belt, See Specifications Pages

45 9.802-522.0 Strain Relief, 1"

46 9.802-765.0 Screw, 1/4" x 1/2",

BH SOC CS

1

47 9.802-817.0 Washer, 3/8" x 1" Steel

48 9.802-710.0 Bolt, 5/16" x 1 NC (551.0)

9.802-720.0 Bolt, 3/8" x 1" NC, HH

(552.0-560.0)

49 9.800-034.0 Label, Clear Lexan,

2-1/4" x 4-1/2"

50 9.802-073.0 Weather Stripping

12

4

4

4

1

7 ft.

51 9.802-779.0 Nut, 3/8" ESNA, NC

(552.0-560.0) 4

9.802-776.0 Nut, 5/16", ESNA, NC (551.0) 4

52 9.802-800.0 Washer, 1/2" Flat

53 9.803-081.0 Cover, Access Hole

1

1

54 9.802-773.0 Nut, 1/4", ESNA NC

55 9.802-723.0 Bolt, 3/8" x 1-1/2", NC HH

2

4

56 9.802-067.0 Bumper Pad, Engine 4

57 9.802-811.0 Washer, 3/8" x 1-1/2" Fender 4

58 9.802-431.0 GFCI, 120V 20A w/36'

12-3 Cord (551.0)

9.802-430.0 GFCI, 240V 1Ph, 30A, 36'

10-3 Cord (552.0)

9.802-434.0 GFCI 240V 1Ph 40A, 36'

8-3 Cord (556.0, 559.0)

9.802-429.0 Cord, Serv, SEO 12/4 (553.0,

554.0, 557.0, 558.0)

1

1

1

10 ft.

9.802-437.0 Cord, Service, 10/4 (560.0) 10 ft

59 9.802-794.0 Nut, Cage, 1/4" x 12 Gauge 8

60 9.802-074.0 Nut, 1/4" Square Head

Grommet, Nylon 4

61 9.800-040.0 Label, Ground 1

62 9.802-762.0 Screw, 10/32" x 1-1/4" RH, SL

(552.0-560.0)

(551.0)

1

2

63 9.802-759.0 Screw, 10/32" x 1/2" BHSOC

(552-560.0) 11

64 9.802-695.0 Nut, 10/32" KEPS (551.0)

(552.0-560.0)

65 9.800-020.0 Label, Cold Water Inlet, HS

4

10

1

ITem paRT NO. DeSCRIpTION qTy

66 9.803-278.0 Strain Relief, 3/4", LQ Tite

(551.0)

9.802-518.0 Strain Relief, STRT, LQ Tite

1

(552.0, 553.0, 554.0, 555.0) 1

9.802-526.0 Locknut, 3/4" (551.0) 1

9.803-279.0 Strain Relief, 1" (553.0, 554.0,

555.0, 556.0, 559.0, 560.0) 1

9.803-280.0 Locknut, 1" (553.0, 554.0,

555.0, 556.0, 559.0, 560.0) 1

67 8.932-970.0 Label, Cold Water Outlet

68 9.800-007.0 Label, Warning, Exposed

Pulleys

1

1

69 9.800-013.0 Label, Intended for Indoor Use 1

70 9.802-514.0 Strain Relief, Small, LQ

Tite (Time Delay/Auto-

Start Option) 1

9.802-524.0 Lock-Nut, 1/2" Conduit

(Time Delay/Auto-Start Option) 1

71 9.802-423.0 Cord, Service, SEO, 16/3 2.5 ft.

9.802-424.0 Cord, Service, SEO 16/4

(Time Delay

Shutdown Option) 2.5 ft.

72 9.802-779.0 Nut, 3/8" ESNA 4

73 8.718-980.0 Washer, 5/16" Flat

74 9.802-467.0 Base Relay (Time Delay

Shutdown Option)

4

1

75 9.802-468.0 Relay (Time Delay

Shutdown Option)

76 8.751-306.0 Timer, Multi-Function,

24V-120/240V (Time Delay

Shutdown Option)

1

1

77 9.802-472.0 Timer, Solid State, 120V, 5-60

Mins, Adjustable (Auto Start/

Stop Option) 1

78 9.800-049.0 Label, Manufacturer’s Cleaning

Solution 1

79 8.900-870.0 Label, Shark Logo, Die-Cut 2

80 9.802-802.0 Washer, 1/4 " Flat SAE Zinc 8

81 9.802-700.0 Bolt, 1/4" x 3/4" NC HH

(6/2937) 4

82 9.802-791.0 Nut, Cage, 10/32" x 16 Gauge

(552.0-560.0) 6

▲ Not Shown

17

9.801-262.0 • Shark CB • Rev. 5/13

9.802-362.0

vb8 UNlOaDeR valve explODeD vIeW

27

32

31

26

28

25

6

30 29

27

12

2

16

15

11

39

13

14

13

5

10

9

8

40

36

35

4

7

38

18

34

33 3

2

1

37

18

vb8 UNlOaDeR valve explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION

1 60.0058.31 3/8 Bsp F Outlet Fitting

2 10.3070.02* O-ring 1.78 x 18.77 mm

3 60.0053.51 Spring

4 60.0052.31 Check Valve

5 10.3213.00* O-ring 3 x 6 mm

6 60.1201.35 VB8 Brass Body

7 10.3170.08* O-Ring 2,.62 x 7.6 mm

8 60.1206.31 Piston

9 10.3001.01* O-ring 1 x 4 mm

10 10.3066.01* O-ring 1.78 x 15.6 mm

11 60.1205.31 M 6 Nut

12 60.2221.20* VB8/9 Seat+Shutter

13 10.4021.00* Back Ring 11.4 x 15.9 mm

14 10.3175.00* O-ring 2.62 x 10.77 mm

15 60.1204.31 Spring Guide

16 10.3167.01* O-ring 2.62 x 5.23 mm

17 60.1203.31 Piston Housing

18 16.2100.00 M 4 x 4 mm Dowel

19 60.1704.31 M 22 Nut

20 14.3719.00 Washer 9 x 15 mm

21 60.1208.61 3.2 x 33 mm Spring qTy

1

1

1

1

1

1

1

2

1

2

1

1

1

1

1

1

1

1

1

1

1

ITEM PART NO. DESCRIPTION

22 60.1210.31 Upper Frame

23 14.7421.00 1/4" Ball

24 60.1209.31 Brass Cap

25 29.0087.51 Sst Clip

26 29.0089.84 Plastic Housing

27 12.5006.00 El.Cable + Micro Switch

28 10.3206.01 O-ring 2.62 x 28.25 mm

29 16.3020.00 2.5 x 12 mm screw

30 29.0088.84 Cover

31 10.3169.00 O-ring 2.62 x 6.02 mm

32 29.0082.84 Black Nut-40 Bar

33 10.3038.00 O-ring 1.78 x 3.68 mm

34 14.3519.53 Sst Washer 4 x 8 mm

35 60.2303.51 Spring

36 60.1281.31 PR 5 Pin

1

1

37 60.1202.84 Plastic Handle (60.1290.00) 1

38 14.3582.00 Washer D. 30 mm (60.1290.00) 1

39 60.2254.31 M 30 Nut (60.1290.00) 1

40 29.0096.24 PR 5 Pl.Housing Kit

Kit P/N Description

1

*K1 60.1212.24 VB8 Spare Parts Kit 9x1 pcs 1

1

1

1

2

1

1

QTY

1

1

1

1

1

1

1

9.801-262.0 • Shark CB • Rev. 5/13

24

23

22

21

20

19

17

4

16 auto

Start/Stop

Option

17

3

15

2

pUmp explODeD vIeW

2

1

10

3 4

9

Time Delay

Shutdown

Option

14

8

6

5

11

12

13

98012620-27

pUmp explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION

1 8.750-299.0 Unloader, VRT3, 8 GPM

@ 4500 PSI qTy

2 9.802-039.0 Elbow, 1/2" JIC, 3/8", 90°

3 9.802-048.0 Swivel, 1/2" JIC x 3/8"

Male

4

5

9.802-129.0 Elbow, 1/2" JIC x 3/8"

8.706-790.0 Nipple, 1/2" Close

1

1

6 8.706-844.0 Tee, 1/2" Female Pipe

7 9.802-128.0 Nipple, 1/2" JIC x1/2"

MPT Pipe

8 9.802-131.0 Elbow, 1/2" JIC x 1/2", 90°

9 9.802-151.0 Swivel Push-On, 1/2" JIC

Female

10 9.802-259.0 Hose, 1/2" Push-On

1

1

2

18"

11 9.803-670.0 Protector, Pump, 1/2", 190° 1

12 Pump, See Specifications Pages

13 9.802-632.0 Cap, Valve w/1/4" Gauge Port

(Time Delay Shutdown Option)

(All Except 300.0) 1

9.804-022.0 Cap, Valve w/1/4" Gauge Port

(Time Delay Shutdown

Option (300.0) 1

1

1

1

1

ITem paRT NO. DeSCRIpTION qTy

14 9.802-458.0 Switch, Pressure, N/O, 1/4" NP

(Time DelayShutdown Option) 1

15 9.802-042.0 Elbow, 1/2" JIC x 3/8 Fem, 90°

(Auto Start/Stop Option) 1

16 9.802-362.0 Unloader, PA 8 GPM

@3650 PSI, VB8, w/Switch

(Auto Start/Stop Option)

17 8.706-207.0 Elbow, 3/8 Street

1

1

9.801-262.0 • Shark CB • Rev. 5/13

19

model

1.106-551.0

1.106-552.0

1.106-553.0

1.106-554.0

1.106-555.0

1.106-556.0

1.106-557.0

1.106-558.0

1.106-559.0

1.106-560.0

pump

KD3030R

KM4035R

KM4035R

KM4035R

KM4035R

KM4035R

KM4035R

KM4035R

KM4035R

KM4035R

SpeCIfICaTIONS

pump

P art N o.

9.804-006.0

pump pulley

AK74H pump pulley

P art N o.

9.802-369.0

8.751-189.0

2AK74H 9.802-369.0

8.751-189.0

2AK74H 9.802-369.0

8.751-189.0

2AK74H 9.802-369.0

8.751-189.0

2AK74H 9.802-369.0

8.751-189.0

2BK80H 8.715.592.0

8.751-189.0

2BK80H 8.715.592.0

8.751-189.0

2BK80H 8.715.592.0

8.751-189.0

2BK80H 8.715.592.0

8.751-189.0

2BK80H 8.715.592.0

pump bushing

24MM

24MM

24MM

24MM

24MM

24MM

24MM

24MM

24MM

24MM bushing

P art N o.

Size

9.802-402.0

2HP voltage/ph

120V/1PH

9.802-402.0

6.2HP

230V/1PH

9.802-402.0

6.2HP

230V/3PH

9.802-402.0

6.2HP

460V/3PH

9.802-402.0

6.2HP

208V/3PH

9.802-402.0

7.5HP

230V/1PH

9.802-402.0

7.5HP

230V/3PH

9.802-402.0

7.5HP

460V/3PH

9.802-402.0

7.5HP

208V/1PH

9.802-402.0

7.5HP

208V/3PH

60

60

60

60

60

60 hz

60

60

60

60

20

9.801-262.0 • Shark CB • Rev. 5/13

SpeCIfICaTIONS

model

551.0 p motor art N o.

9.802-339.0

motor pulley

AK32x5/8

Motor P ulley

P art No.

9.804-004.0 motor bushing

N/A motor part No.

N/A belt

Size belt part No.

Contractor part No.

AX40 (1) 9.804-005.0

8.724-268.0

552.0 9.802-336.0 2AK56H 9.802.373.0 HX1-1/8" 9.802-400.0 AX42 (2) 9.802-411.0

8.724-276.0

Overload part No.

N/A

N/A

553.0 8.751-004.0 2AK56H 9.802-373.0 HX1-1/8" 9.802-400.0 AX42 (2) 9.802-411.0

8.724-268.0

8.724-304.0

554.0 8.751-004.0

2AK56H 9.802-373.0 HX1-1/8" 9.802-400.0 AX42 (2) 9.802-411.0 8.724-268.0 8.724-312.0

555.0 9.802-330.0 2AK56H 9.802-373.0 HX1-1/8" 9.802-401.0 AX42 (2) 9.802-411.0 8.724-268.0 8.724-304.0

556.0 8.715-097.0 2BK52H 9.802-386.0 HX1-3/8" 9.802-401.0 BX43 (2) 9.802-420.0 8.724-276.0

8.724-306.0

557.0 8.751-014.0 2BK50H 8.751-583.0 HX1-3/8" 9.802-401.0 BX43 (2) 9.802-420.0 8.724-268.0 8.724-304.0

558.0 8.751-014.0 2BK50H 8.751-583.0 HX1-3/8" 9.802-401.0 BX43 (2) 9.802-420.0 8.724-268.0

8.724-312.0

559.0 9.802-332.0 2BK52H 9.802-386.0 HX1-3/8" 9.802-401.0 BX43 (2) 9.802-420.0 8.724-276.0

8.724-306.0

560.0 9.802-333.0 2BK52H 9.802-386.0 HX1-3/8" 9.802-401.0 BX43 (2) 9.802-420.0 8.724-268.0 8.724-305.0

9.801-262.0 • Shark CB • Rev. 5/13

21

mUlTI-ROOm INSTallaTION

98012020-26

22

9.801-262.0 • Shark CB • Rev. 5/13

9.803-417.0 kD 3025.1

9.804-006.0 kD 3030.1

9.804-019.0 kD 4020.1

kD.1 pUmp explODeD vIeW

TORqUe

SpeCS

Item # Ft.-lbs

14

17

25

34

65

18

7.6

7

44 13

kD.1 pUmp explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION

1 9.803-938.0 Crankcase

2* See Kits

3* See Kits

Plunger Oil Seal

O-Ring Ø1.78 x 28.30

4* See Kits

See Kits

5* See Kits

See Kits

6* See Kits

See Kits

Pressure Ring 15mm (3030)

Pressure Ring 18mm

(4020, 3025)

U-Seal, 15mm (3030)

Intermediate 18mm

(4020, 3025) qTy

1

3

3

3

3

3

U-Seal, 18mm (4020, 3025) 3

Intermediate Ring 15mm (3030) 3

3

7* SSee Kits Intermed. Ring 15mm (3030) 3

See Kits Intermed. Ring 18mm

(4020, 3025) 3

8 9.802-926.0 Brass Plug 1/2"

9 9.803-199.0 Copper Washer 1/2"

10 9.803-946.0 Manifold Housing 1

1

1

ITem paRT NO. DeSCRIpTION

11* See Kits O-Ring Ø1.78 x 15.54

12* See Kits

13* See Kits

Valve Assembly

O-Ring Ø2.62 x 18.77

14 9.803-949.0 Valve Plug

15 9.803-950.0 Copper Washer 1/4

16 9.803-951.0 Brass Plug G1/4

17 9.803-952.0 Manifold Stud Bolt

18 9.802-884.0 Washer

19 9.803-198.0 Copper Washer 3/8

20 9.802-925.0 Brass Plug 3/8

25 9.802-939.0 Screw

26 9.803-953.0 Bearing Cover

27 9.803-954.0 Bearing Seal

28 9.802-914.0 Snap Ring

29 9.803-955.0 Ball Bearing

30 9.803-956.0 Crankshaft

31 9.803-167.0 Crankshaft Key

32 9.803-957.0 Oil Dipstick

9.801-262.0 • Shark CB • Rev. 5/13

1

8

8

6

1 qTy

6

6

6

1

1

2

1

1

2

12

2

1

1

23

24

kD.1 pUmp explODeD vIeW paRTS lIST (CONT)

ITem paRT NO. DeSCRIpTION

33 8.933-010.0 Crankshaft Seal

34* See Kits

35* See Kits

Plunger Nut

Copper Spacer

36* See Kits

See Kits

37* See Kits

38* See Kits

Plunger, 15mm (3030)

Plunger, 18mm (4020, 3025)

Copper Spacer

O-Ring Ø1.78 x 5.28

39* See Kits

40* See Kits

Teflon Ring

Plunger Rod

41 9.803-965.0 Connecting Rod Pin

42 9.803-966.0 Connecting Rod

3

3

3

3 qTy

1

3

3

3

3

3

3

43 9.803-218.0 Spring Washer

44 8.933-020.0 Connecting Rod Screw

45 9.803-202.0 Sight Glass

46 9.803-197.0 Gasket

47 9.803-968.0 Crankcase Cover

48 9.803-969.0 O-Ring Ø2.62 x 107.62

* Available in kit (See below)

1

1

6

6

1

1

REPAIR KIT NUMBER

KIT DESCRIPTION

ITEM NUMBERS

INCLUDED

NUMBER OF CYLINDERS

KIT WILL SERVICE

8.725-354.0

Plunger Seal

15mm

3030

3, 5, 7

3

REPAIR KIT NUMBER

KIT DESCRIPTION

ITEM NUMBERS

INCLUDED

NUMBER OF CYLINDERS

KIT WILL SERVICE

9.803-934.0

Plunger

15mm

3030

34, 35, 36,

37, 38, 39, 40

1

8.725-356.0

Plunger Seal

18mm

3025

4020

3, 5, 7

3

8.725-355.0

Complete Seal

Packing, 15mm

3030

3, 4, 5,

6, 7

1

8.725-357.0

Complete Seal

Packing, 18mm

3025

4020

3, 4, 5,

6, 7,

1

9.803-935.0

Plunger

18mm

3025

4020

34, 35, 36, 37,

38, 39, 40

1

9.803-936.0

Complete Valve

11, 12, 13

6

9.803-937.0

Plunger Oil Seals

2

3

9.801-262.0 • Shark CB • Rev. 5/13

8.751-186.0 km3540R.3

8.751-187.0 km4030R.3

8.751-188.0 km4030l.3

8.751-189.0 km4035R.3

8.751-190.0 km4035l.3

8.751-191.0 km5030R.3

8.751-192.0 km5030l.3

km.3 SeRIeS pUmp explODeD vIeW

TORqUe

SpeCS

Item # Ft.-lbs

14 75

15

23

33

43

48

30

8

9

13

7.6

km.3 SeRIeS pUmp explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION

1 8.751-216.0 Crankcase

2* See Kits Below Plunger Oil Seal

3* See Kits Below O-Ring Ø1.78 x 31.47

4* See Kits Below Pressure Ring

5* See Kits Below U-Seal

6* See Kits Below Intermediate Ring

7* See Kits Below U-Seal

8 9.803-199.0 Washer, Copper

9 9.802-926.0 Plug, Brass 1/2

10 8.751-218.0 Manifold Head

11* See Kits Below O-Ring Ø2.62 x 17.13

12* See Kits Below Valve Assembly

13* See Kits Below O-Ring Ø2.62 x 20.29

14 9.802-928.0 Valve Plug

15 9.802-938.0 Manifold Stud Bolt

16 9.802-884.0 Washer

17 9.803-198.0 Copper Washer 3/8

18 9.802-925.0 Brass Plug 3/8 qTy

1

3

6

8

16

1

1

6

6

6

3

3

1

1

1

3

3

3

9.801-262.0 • Shark CB • Rev. 5/13

ITem paRT NO. DeSCRIpTION

23 9.802-944.0 Screw, Hex, 8mm x18mm

24 8.717-210.0 Closed Bearing Housing

25 9.803-192.0 O-Ring Ø1.78 x 60.05

26 8.933-011.0 Tapered Roller Bearing

27 8.751-222.0 Crankshaft (5030,3540)

8.751-223.0 Crankshaft (4030, 4035)

28 9.803-167.0 Crankshaft Key

29 9.802-921.0 Oil Dip Stick

30 9.803-140.0 Crankshaft Seal

31 9.803-178.0 Shim

32 8.717-209.0 Bearing Housing

33* See Kits Below Plunger Nut, M8

34* See Kits Below Copper Spacer

35* See Kits Below Plunger (4035)

See Kits Below Plunger (4030, 5030)

See Kits Below Plunger (3540) qTy

8

1

1

2

1

3

3

3

3

3

1

1

1

2

2

1

25

km.3 SeRIeS pUmp explODeD vIeW paRTS lIST

ITem paRT NO. DeSCRIpTION

36* See Kits Below Copper Spacer

37* See Kits Below O-Ring Ø1.78 x 7.66

38* See Kits Below Teflon Ring

39 8.751-224.0 Plunger Rod

40 9.803-158.0 Connecting Rod

41 8.751-228.0 Connecting Rod Pin

42 9.803-218.0 Spring Washer

43 9.803-238.0 Connecting Rod Screw

44 8.933-016.0 O-Ring, Ø2.62 x 126.67

45 8.751-229.0 Crankcase Cover

46 9.803-197.0 O-Ring, Ø1.78 x 14

47 9.803-202.0 Sight Glass 3/4

48 9.802-939.0 Cover Screw

* Available in kit (See below) qTy

3

1

1

1

6

6

1

5

3

3

3

3

3

REPAIR KIT NO.

8.725-360.0

KIT

DESCRIPTION

ITEM NUMBERS

INCLUDED

NO. OF CYLINDERS

KIT WILL SERVICE

Plunger Seal

4035

18mm

3, 5, 7

3

8.725-362.0

8.725-358.0

8.725-361.0

Plunger Seal

4030

5030

20mm

8.725-363.0

Plunger Seal

3540

15mm

Complete Seal

Packing

4035

18mm

Complete Seal

Packing

4030

5030

20mm

8.725-359.0

Complete Seal

Packing

3540

15mm

3, 5, 7 3, 5, 7 3, 4, 5, 6, 7 3, 4, 5, 6, 7 3, 4, 5, 6, 7

3 3 1 1 1

REPAIR KIT NO.

KIT

DESCRIPTION

ITEM NUMBERS

INCLUDED

NO. OF CYLINDERS

KIT WILL SERVICE

8.751-237.0

Plunger

4035

18mm

8.751-238.0

8.933-023.0

9.802-603.0

Plunger

4030

5030

20mm

Plunger

3540

15mm

33, 34, 35, 36,

37, 38

33, 34, 35, 36,

37, 38

33, 34, 35, 36,

37, 38

Complete Valve

11, 12, 13

1 1 1 6

9.802-609.0

Plunger Oil

Seals

2

3

26

9.801-262.0 • Shark CB • Rev. 5/13

vRT3 UNlOaDeR explODeD vIeW aND paRTS lIST

8.750-297.0, 8 GPM, 2320 PSI

8.750-298.0, 8 GPM, 3630 PSI

8.750-299.0, 8 GPM, 4500 PSI

20

14

ITem paRT NO. DeSCRIpTION

25 8.750-713.0 Outlet Fitting

18 8.750-712.0 Knob, Unloader qTy

1

1

8.750-709.0 Repair Kit, VRT3, 2320/3630 PSI

8.750-710.0 Repair Kit, VRT3, 4500 PSI

(Kit Items: 3, 4, 6, 9-12, 21, 24)

19 8

18

17

16

13

15

15

6

12

11

26

3

4

5

6

9

10

9

1

21

22

23

24

2

7

25

Unloader adjustment procedures

1. Remove lock nut (Item 19).

2. Remove adjustment knob (Item 18).

3. Loosen the two (2) nuts (Item 15), move them upward on stem (Item 8) until you see 4 or more threads below the nut.

4. Re-attach adjusting knob (Item 18).

5. Start machine. Open the trigger of the spray gun. Increase pressure by turning adjustment knob (Item 18) clockwise until pressure is at the desired operating pressure.

6. Remove the adjustment knob (Item 18), tighten the lower nut (Item 15) tightly against the upper nut (Item 15).

Re-attach adjustment knob (Item 18) and screw down until contact is made with the nuts (Items 15). Screw down lock nut

(Item 19) onto the stem (Item 8) until the threads cut into the nylon insert of the lock nut (Item 19).

*If adjustment knob (Item 18) DOeS NOT make contact with upper nut (Items 15), remove adjusting knob (Item 18), re-adjust

(raise) nuts (Items 15) on stem (Item 8) and re-attach adjustment knob (Item 18), then repeat step #6.

**If adjustment knob (Item 18) DOeS make contact with upper nut; release the trigger of the spray gun and watch the pressure gauge for the pressure increase (“spike”). This “spike” ShOUlD NOT exceed 500 psi above the operating pressure.

If “spike” pressure exceeds the 500 psi limit, remove the adjusting knob (Item 18) and re-adjust (lower) the nuts (Items 15) on the stem (Item 8). Re-attach the adjusting knob (Item 18), then repeat step #6.

27

9.801-262.0 • Shark CB • Rev. 5/13

28

LIMITED NEW PRODUCT

WARRANTY—COMMERCIAL

PRESSURE WASHERS

Phone: 800-771-1881

Fax: 877-526-3246 www.sharkpw.com

WHAT THIS WARRANTY COVERS

All Shark pressure washers are warranted by Shark to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty, subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this warranty will assume the remainder of the pressure washer’s warranty period.

FIVE YEAR PARTS AND ONE YEAR LABOR WARRANTY

Components manufactured by Shark, such as frames, handles, float tanks, fuel tanks, belt guards, and heating coils. Pro-Duty rated units

(DD Series) have a three-year limited warranty against defects and workmanship. Internal components on the oil-end of Kärcher axial pumps have a 5 year warranty. Kärcher crankshaft pumps have a 7 year warranty on non-wear parts. Heating coils are pro-rated at 25% after 2 years.

Kärcher and non-Kärcher swash and wobble plate pumps have a one year warranty; other pumps carry their manufacturer’s warranty.

ONE YEAR PARTS AND ONE YEAR LABOR WARRANTY

All other components, excluding normal wear items as described below, will be warranted for one year on parts and labor. Parts and labor warranty on these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.

WARRANTY PROVIDED BY OTHER MANUFACTURERS

Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufacturers’ local authorized service centers. Shark is not authorized and has no responsibility to provide warranty service for such components.

Motors manufactured outside of the United States will be warranted by Shark.

WHAT THIS WARRANTY DOES NOT COVER

This warranty does not cover the following items:

1. Normal wear items, such as nozzles, spray guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings, packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.

2. Any components or other devices incorporated into a Shark product that are not manufactured by Shark, including, but not limited to gasoline engines, pumps, etc.

3. Defects caused by improper or negligent operation or installation, accident, abuse, misuse, neglect, unauthorized modifications, repair or maintenance of the product by persons other than authorized representatives of Shark, including, but not limited to, the failure of the Customer to comply with recommended product maintenance schedules.

4. Shark products that have been returned by the original Customer and are ultimately re-sold by an Authorized Servicing

Dealer or other sales or service outlet to another purchaser.

5. Shark products that are sold by any distributor or retailer that is not an official authorized dealer or retailer of Shark products.

6. Defects caused by acts of nature and disaster including, but not limited to, floods, fires, wind, freezing, earthquakes, tornadoes, hurricanes and lightning strikes.

7. Defects caused by water sediments, rust corrosion, thermal expansion, scale deposits or a contaminated water supply (such as water in the unit with chloride content higher than that of 80 mg/liter or use of chemicals not approved or recommended by Shark).

8. Defects caused by improper voltage, voltage spikes or power transients in the electrical supply.

9. Devices or accessories not distributed or approved by Shark.

10. Any cost of labor arising from the removal and reinstallation of the alleged defective part by Customer.

11. Transportation of the product to an Authorized Servicing Dealer, field labor, replacement rental and any freight charges.

Any components, accessories or other devices provided with the product but not manufactured by Shark (such as engines, pumps, etc.) are subject to warranties and service through their respective manufacturers authorized service centers and according to the applicable terms and conditions of such manufacturers warranties. Such components or other devices not manufactured by Shark should be referred by the Customer to an authorized service center or their respective manufacturers for repair or replacement.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, WHETHER ARISING BY LAW, CUSTOM

OR CONDUCT. SHARK MAKES NO ADDITIONAL WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, ANY EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS OF EQUIPMENT FOR A

PARTICULAR PURPOSE AND ANY SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. SHARK FURTHER DISCLAIMS

ANY WARRANTY THAT THE PRODUCT PURCHASED BY CUSTOMER WILL MEET ANY PARTICULAR REQUIREMENT

OF CUSTOMER EVEN IF SHARK HAS BEEN ADVISED OF SUCH REQUIREMENT.

THE RIGHTS AND REMEDIES PROVIDED UNDER THIS WARRANTY ARE EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS

OR REMEDIES OF CUSTOMER. SHARK SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANY PERSON OR

ENTITY INCLUDING, BUT NOT LIMITED TO, THE CUSTOMER OR ANY END USER OF THE PRODUCT FOR ANY SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ECONOMIC LOSS, LOSS OF PROFITS OR LOSS OF USE OF

THE PRODUCT, ARISING IN CONNECTION WITH THE SALE, DELIVERY, INSTALLATION, TRAINING OR USE OF PRODUCT.

SHARK’S LIABILITY, WHETHER IN CONTRACT OR IN TORT, ARISING OUT OF ANY WARRANTIES OR REPRESENTA-

TIONS, INSTRUCTIONS OR DEFECTS FROM ANY CAUSE, SHALL BE LIMITED EXCLUSIVELY TO THE COST OF REPAIR OR

REPLACEMENT PARTS UNDER AFORESAID CONDITIONS.

The purpose of the foregoing limitations on liability and Customer remedies is to protect Shark from unknown or undeterminable risks. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the Customer.

Shark sales and service representatives are not authorized to waive or alter the terms of this warranty, or to increase the obligations of Shark under the warranty.

Shark reserves the right to make design changes in any of its products without prior notification to the Customer.

9.801-262.0 • Shark CB • Rev. 5/13

www.sharkpw.com

Shark CB 9.801-262.0 • Revised 5/13 • Printed in U.S.A. or Mexico