Zenoah BC2001 Specifications

Add to my manuals
44 Pages

advertisement

Zenoah BC2001 Specifications | Manualzz
T1006-93110(010)
OWNER / OPERATOR MANUAL
BRUSHCUTTERS
BC2300DL
BC2600DL
BC3400DL
BC4400DW
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Thank you for purchasing a RedMax
product.
Before using our brushcutters, please
read this manual carefully to understand
the proper use of your unit.
APPLICABLE SERIAL NUMBERS :
BC2300DL
BC2600DL
BC3400DL
BC4400DW
DRIVE UNIT
DRIVE UNIT
DRIVE UNIT
DRIVE UNIT
500000000 and up
500000000 and up
980101 and up
980101 and up
ENGINE UNIT
ENGINE UNIT
ENGINE UNIT
ENGINE UNIT
990639
978729
980101
980101
and up
and up
and up
and up
Read this manual carefully to understand
all safety precautions, controls, proper
operation and maintenance of your
RedMax brushcutters. Failure to do so
could result in serious injury.
SAFETY FIRST
Instructions contained in warnings within this manual marked with a
symbol
concern critical points which must be taken into consideration to prevent
possible serious bodily injury, and for this reason you are requested to read all
such instructions carefully and follow them without fail.
Note that there may be times when warning seals peel off or become soiled and
impossible to read. If this happens, you should contact the dealer from which
you purchased the product to order new seals and affix the new seal(s) in the
required location(s).
■ Notes on types of warnings
WARNING
IMPORTANT
NOTE
Instructions labeled as shown at left, concern critical steps or
procedures which must be followed in order to prevent accidents
which could lead to serious bodily injury or death.This mark is
used to indicate instructions which must be followed without
exception.
Instructions labeled as shown at left concern steps or procedures
which, if not followed correctly, could lead to mechanical failure,
breakdown, or damage.
Used to label supplementary instructions designed to provide
hints or directions useful in the use of the product.
CONTENTS
SAFETY PRECAUTIONS············································································· 4
IN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR BRUSHCUTTER
WORK GEAR AND CLOTHING
WARNINGS CONSIDERING HANDLING OF FUEL
THINGS TO CHECK BEFORE USING YOUR BRUSHCUTTER
THINGS TO CHECK BEFORE STARTING UP THE ENGINE
AVOID NOISE PROBLEM
THINGS TO BE CAREFUL ABOUT WHEN USING YOUR BRUSHCUTTER
NOTES ON CARE AND MAINTENANCE OF YOUR BRUSHCUTTER
SET UP ········································································································· 9
MOUNTING ENGINE
INSTALLING HANDLE
INSTALLING DEBRIS GUARD
CONNECTING THROTTLE WIRE
CONNECTING SWITCH WIRES
PUTTING ON WAIST PAD
INSTALLING CUTTING HEAD
FUEL ··········································································································· 11
HOW TO MIX FUEL
FUELING THE UNIT
OPERATION ······························································································· 12
STARTING ENGINE
STOPPING ENGINE
ADJUSTING IDLING SPEED
LINE HEAD USAGE
METAL BLADE USAGE
OPTIONAL BLADE USAGE ······································································ 15
CHOOSE THE BLADE
SET UP
STARTING ENGINE
CUTTING METHOD
OPERATION
CONTROLLING BLADE BOUNCE
MAINTENANCE
TRANSPORTING THE UNIT
MAINTENANCE ························································································· 20
REFILLING TRIMMING LINE
AIR FILTER
FUEL FILTER
SPARK PLUG
MUFFLER
SPARK ARRESTER
GEAR CASE
STORAGE ·································································································· 22
SPECIFICATIONS ······················································································ 23
PARTS LIST
BC2300DL·························································································································· 26. 28
BC2600DL·························································································································· 26. 30
BC3400DL·························································································································· 32. 34
BC4400DW ························································································································ 36. 38
Safety Precautions
■ In order to ensure proper and safe
operation of your brushcutter
• Read this Owner/Operator Manual
carefully. Be sure you understand how to
operate this unit properly before you use
it. Failure to do so could result in serious
injury.
• Be sure to keep this manual handy so that
you may refer to it later whenever any
questions arise. Also note that you are
requested to contact the dealer from
whom you purchased the product for
assistance in the event that you have any
questions which cannot be answered
herein.
• Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this product.
• This product has been designed for use in
cutting grass, and it should never be used
for any other purpose since doing so could
result in unforeseen accidents and injuries
occurring.
• You should never use this brushcutter
when under the influence of alcohol, when
suffering from exhaustion or lack of sleep,
when suffering from drowsiness as a result
of having taken cold medicine, or at any
other time when a possibility exists that
your judgment might be impaired or that
you might not be able to operate the
brushcutter properly and in a safe manner.
Also be sure never to allow children or
anyone unable to fully understand the
directions given in this manual to use this
brushcutter.
❲4 ❳
• Avoid running the engine indoors. The
exhaust gases contain harmful carbon
monoxide.
• Never use your brushcutter under
circumstances like those described below:
1. When the ground is slippery or when
other conditions exist which might make
it not possible to maintain a steady
posture while using the brushcutter.
2. At night, at times of heavy fog, or at any
other times when your field of vision
might be limited and it would be difficult
to gain a clear view of the area where
the brushcutter is to be used to ensure
safety.
3. During rain storms, during lightning
storms, at times of strong or gale-force
winds, or at any other times when
weather conditions might make it unsafe
to use this product.
• When using this product for the first time,
before beginning actual work, take the
brushcutter to a wide, clear, open space,
turn on the power, and practice handling
the brushcutter until you are sure that you
will be able to handle in it properly in actual
operation.
• Lack of sleep, tiredness, or physical
exhaustion results in lower attention spans,
and this in turn leads to accidents and
injury. When planning your work schedule,
allow plenty of time to perform the work of
cutting and allow plenty of time for rest.
Limit the amount of time over which the
brushcutter is to be used continuously to
somewhere around 30~40 minutes per
session, and take 10~20 minutes of rest
between work sessions. Also try to keep
the total amount of work performed in a
single day under 2 hours or less.
Safety Precautions
■ Work gear and clothing
■ Warnings considering handling of fuel
• When using your brushcutter, always be
sure to wear strong, durable, work clothing;
shirts should be long-sleeved shirts and
pants should be full-length pants reaching
down to the ankles.
• The engine of the RedMax® brushcutter is
designed to run on a mixed fuel which
contains highly flammable gasoline. This
fuel is highly flammable and you should
never store cans of fuel or refill the tank of
the brushcutter in any place where there is
a boiler, stove, wood fire, electrical sparks,
welding sparks, or any other source of heat
or fire which might ignite the fuel.
• Always be sure to wear helmet and face
protector when using your brushcutter.
• When using your brushcutter, always be
sure to wear thick work gloves to protect
your hands and non-slip-sole work boots to
prevent you from slipping. Never use your
brushcutter when wearing pants with loose
cuffs, when wearing sandals, or when
barefoot.
• When using your brushcutter for an
extended period of time, you should wear
ear protectors to protect yourself from loss
of hearing from overexposure to high levels
of sound.
• Smoking while operating the brushcutter or
refilling its fuel tank is extremely
dangerous. Always be sure to keep lit
cigarettes away from the brushcutter at all
times.
• When refilling the tank, always turn off the
engine first and take a careful look around
to make sure that there are no sparks or
open flames anywhere nearby before
refueling.
• If any fuel spillage occurs during refueling,
always be sure to use a dry rag to wipe any
fuel which has been spilled onto the
brushcutter before turning the engine back
on again.
• After refueling, screw the fuel cap back
tightly onto the fuel tank and then carry the
brushcutter to a spot 10 feet (3m) or more
away from where it was refueled before
turning on the engine.
❲5 ❳
Safety Precautions
■ Things to check before using your
brushcutter
■ Things to check before starting up the
engine
• Before beginning work, look around
carefully to get a feel for the shape of the
land, grass to be trimmed, and whether or
not there are any obstacles which might get
in the way while working, and remove any
obstacles before beginning work.
• Take a careful look around to make sure
that no obstacles exist within a perimeter of
15 feet (5m) or less around the brushcutter
before starting the engine.
• The area within a perimeter of 50 feet
(15m) of the person using the brushcutter
should be considered a hazardous area
into which no one should enter while the
brushcutter is in use, and when necessary
yellow warning rope, warning signs, or
some other form of warnings should be
placed around the perimeter of the area.
When work is to be performed
simultaneously by two or more persons,
care should also be taken to constantly
look around or otherwise check for the
presence and locations of other people
using brushcutters within the work area so
as to maintain a distance between each
person sufficient to ensure safety.
• Before beginning work, each component of
the brushcutter should be checked to make
sure that it is in proper working order and to
make sure that there are no loose screws
or bolts, fuel leaks, ruptures, dents, or any
other problems which might interfere with
safe operation. Be especially careful at this
time to check that there is nothing wrong
with the blades or with the joints by which
the blades are attached to the brushcutter.
• The RedMax brushcutter is equipped with a
centrifugal clutch mechanism which causes
the cutting blades to begin to rotate as
soon as the engine is started by putting the
throttle into the start position. When starting
the engine, place the body of the
brushcutter onto the ground in a flat clear
area and hold it firmly in place so as to
ensure that neither the blades nor the
throttle come into contact with any
obstacles when the engine starts up.
• Never place the throttle into the high speed
position when starting the engine.
• After starting up the engine, check to make
sure that the blades stop rotating when the
throttle is moved fully back to its original
position. If the blades continue to rotate
even after the throttle has been moved fully
back, turn off the engine and take the unit
to your authorized Red Max servicing
dealer for repair.
■ AVOID NOISE PROBLEM
NOTE
Check and follow the local regulations
as to sound level and hours of
operations for brushcutter.
• In general, operate brushcutters between
8a.m.and 5p.m.on week days and 9a.m.to
5p.m.weekends. Avoid using brushcutter
late at night and/or early in the morning.
❲6 ❳
Safety Precautions
■ Things to be careful about when using
your brushcutter
• When using your brushcutter, grip the
handles of the brushcutter firmly with both
hands, place your feet slightly apart
(slightly further apart than the width of your
shoulders) so that your weight is distributed
evenly across both legs, and always be
sure to maintain a steady, even posture
while working.
• Maintain the speed of the engine at the
level required to perform cutting work, and
never raise the speed of the engine above
the level necessary.
• Always be sure never to allow other
persons to come within the work area while
cutting.
• Be especially careful not to slip if it is
raining or if rain has just stopped, as the
ground is likely to be slippery at such times.
• If the grass or other object gets caught in
the blade during operation, always be sure
to turn off the engine before removing the
object.
• Guard against hazardous situations at all
times. Warn adults to keep pets and
children away from the area. Establish a
safe method for gaining your attention
during operation. Be careful if you are
approached.
• If someone calls out or otherwise interrupts
you while working, always be sure to turn
off the engine before turning around.
• Keep operation area clear of all persons,
particularly small children and pets. Injury
may result from flying debris.
• Never touch the spark plug or plug cord
while the engine is in operation. Doing so
may result in being subjected to an
electrical shock.
• Never touch the muffler, spark plug, or
other metallic parts of the engine while the
engine is in operation or immediately after
shutting down the engine. These metallic
parts reach high temperatures during
operation and doing so could result in
serious burns.
• When you finish cutting in one location and
wish to continue work in another spot, turn
off the engine, place the protective cover
over the blades, and turn the brushcutter
so that the blade face away from your body
before carrying it to the new location.
• Never transport the brushcutter over rough
roads over long distances without removing
all fuel from the fuel tank. If doing so, fuel
might leak from the tank during transport.
❲7 ❳
Safety Precautions
■ Notes on care and maintenance of your
brushcutter
• In order to maintain your brushcutter in
proper working order, perform the
maintenance and checking operations
described in this manual at regular
intervals. In the event that any parts must
be replaced or any maintenance or repair
work not described in this manual must be
performed, please contact a representative
from the store nearest RedMax authorized
servicing dealer for assistance.
• Under no circumstances should you ever
take apart the brushcutter or alter it in any
way. Doing so might result in the
brushcutter becoming damaged during
operation or the brushcutter becoming
unable to operate properly.
• Always be sure to turn off the engine before
performing any maintenance or checking
procedures.
• When sharpening, removing, or reattaching
the blade, be sure to wear thick, sturdy
gloves and use only proper tools and
equipment to prevent injury.
• When replacing blade or any other parts or
when replacing the oil or any lubricants,
always be sure to use only RedMax
products or products which have been
certified by RedMax for use with the
RedMax brushcutter.
• Do not use any accessory or attachment
other than those bearing the RedMax mark
and recommended for the unit.
❲8 ❳
Set up
■ MOUNTING ENGINE
(BC2300DL & BC2600DL)
1. Remove the clamp temporarily attached to
the clutch housing.
2. Push the driveshaft toward the gearcase
and rotate it by hand to check that the
driveshaft is engaged with the gears.
3. Insert the shaft tube into the clutch
housing until it bottoms. When difficult to
engage, twist the engine slightly.
4. Align the positioning holes on the clutch
housing and the shaft tube and fit the boss
on the clamp into the holes. Fasten the
clamp securely.
(BC3400DL & BC4400DW)
• Put the engine onto the clutch side end of
the driveshaft assembly, making the fuel
tank and the cutter head come to the same
side. Attach the engine firmly with the 4
screw provided.
BC4400DW
■ INSTALLING DEBRIS GUARD
• Put the debris guard on the shaft tube near
the gear box, attach it with the 2 screws
and hardware provided.
■ CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to the
joint on the top of the carburetor.
■ INSTALLING HANDLE
• Mount the handle to the shaft tube and
clamp it at your best operating position.
NOTE
(BC3400DL & BC4400DW)
• When installing the cleaner cover, make
sure to put the high-tension wire in it.
❲9 ❳
Set up
■ CONNECTING SWITCH WIRES
• Connect the switch wires between the
engine and the main unit. Pair the wires of
the same color.
■ PUTTING ON WAIST PAD
(BC4400DW only)
• Warp the waist pad around the shaft tube
and the throttle wire.
❲ 10 ❳
■ INSTALLING CUTTING HEAD
1. While locking the gear shaft by inserting
the attached bar into the upper holder and
the gear box, loosen and remove the
hexagon bolt(left-handed)
2. Fit the spacer attached to the head
assembly between the upper and lower
holders. Then screw in the cutting head to
the gear shaft over the holders. Handtighten it securely.
Fuel
WARNING
• Gasoline is very flammable. Avoid
smoking or bringing any flame or
sparks near fuel. Make sure to stop the
engine and allow it cool before
refueling the unit. Select outdoor bare
ground for fueling and move at least
3m(10ft) away from the fueling point
before starting the engine.
• The RedMax engines are lubricated by oil
specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available, use an anti-oxidant added quality
oil expressly labeled for air-cooled 2-cycle
engine use.
RECOMMENDED MIXING RATIO
GASOLINE 32:OIL 1
• Poor quality gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
■ HOW TO MIX FUEL
1. Measure out the quantities of gasoline and
oil to be mixed.
2. Put some of the gasoline into a clean,
approved fuel container.
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate
again for at least one minute.
5. Put a clear indication on the outside of the
container to avoid mixing up with gasoline
or other containers.
6. Indicate the contents on outside of
container for easy identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the
cap on a dustless place.
2. Put fuel into the fuel tank to 80% of the full
capacity.
3. Fasten the fuel cap securely and wipe up
any fuel spillage around the unit.
WARNING
• Exhaust emission are controlled by the
fundamental engine parameters and
components(eq., carburation, ignition
timing and port timing) without addition
of any major hardware or the
introduction of an inert material during
combustion.
32:1 MIXING CHART
GASOLINE
gal. 1 2 3 4 5
2-CYCLE OIL fl.oz 4 8 12 16 20
GASOLINE
liter
2-CYCLE OIL ml
1 2 3 4 5
32 64 96 128 160
• These engines are certified to operate on
unleaded gasoline.
• Make sure to use gasoline with a minimum
octane number of 90 ROZ(USA/Canada :
pump octane min.87)
• Unleaded gasoline is recommended to
reduce the contamination of the air for the
sake of your health and the environment.
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away
from the fueling point before starting the
engine.
3. Stop the engine before refueling the unit.
FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) –
It will cause severe damage to the internal
engine parts very quickly.
2. GASOHOL – It can cause deterioration of
rubber and/or plastic parts and disruption
of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE or
WATER COOLED 2-CYCLE ENGINE
USE – It can cause spark plug fouling,
exhaust port blocking, or piston ring
sticking.
4. Mixed fuels which have been left
unused for a period of one month or
more may clog the carburetor and result
in the engine failing to operate properly.
❲ 11 ❳
Operation
WARNING
4. Shift the ignition switch to the START
position.
• Keep bystanders and animals at least 50
feet (15m) away from the operating
point. If you are approached,
immediately stop the engine.
■ STARTING ENGINE
1. Rest the unit on a flat, firm place. Keep the
cutting head off the ground and clear of
surrounding objects as it will start rotating
upon starting of the engine.
2. Pump the primer until fuel flows out in the
clear tube.
3. Move the choke lever upward to close the
choke.
5. (For BC2300DL/BC2600DL/BC3400DL)
• While pulling the throttle lever with the little
finger of your left hand, pull the starter
rope.
(For BC4400DW)
• Lock the throttle lever at the start position
as shown in the figure right. While holding
the unit firmly against the ground, pull the
starter rope vigorously.
❲ 12 ❳
Operation
WARNING
• The product is equipped with a
centrifugal clutch mechanism, so the
cutting attachment begins to rotate as
soon as the engine is started by putting
the throttle into the start position. When
starting the engine, place the product
onto the ground in a flat clear area and
hold it firmly in place so as to ensure
that neither the cutting part nor the
throttle come into contact with any
obstacle when the engine starts.
NOTE
• Except for an emergency, avoid stopping
the engine while pulling the throttle lever.
■ ADJUSTING IDLING SPEED
1. When the engine tends stop frequently at
idling mode, turn the adjusting screw
clockwise.
2. When the cutting head keeps rotating after
releasing the trigger, turn the adjusting
screw counter-clockwise.
NOTE
• Avoid pulling the rope to its end or returning
it by releasing the knob. Such actions can
cause starter failures.
6.When the engine has started, move the
choke lever gradually downward to open
the choke.
7.Allow the engine to warm up for a half
minute before starting operation.
NOTE
1.When restarting the engine immediately
after stopping it, leave the choke open.
2.Overchoking can make the engine hard to
start due to excess fuel. When the engine
failed to start after several attempts, open
the choke and repeat pulling the rope, or
remove the spark plug and dry it.
■ STOPPING ENGINE
1. Release the throttle lever and run the
engine for a half minute.
2. Shift the ignition switch to the STOP
position.
NOTE
• Warm up the engine before adjusting the
idling speed.
■ LINE HEAD USAGE
WARNING
1. Always wear eye protection such as
safety goggles. Never lean over the
rotating cutting head. Rocks or other
debris could be thrown into eyes and
face and cause serious personal injury.
2. Keep the debris guard attached in
place at all times when the unit is
operated.
TRIMMING GRASS AND WEEDS
• Always remember that the TIP of the line
does cutting. You will achieve better results
by not crowding the line into the cutting
area. Allow the unit to trim at its own pace.
1. Hold the unit so the head is off the ground
and is tilted about 20 degrees toward the
sweep direction.
❲ 13 ❳
Operation
2. Use full throttle when cutting.
3. You can avoid thrown debris by sweeping
from your left to the right.
4. Use a slow, deliberate action to cut heavy
growth. The rate of cutting motion will
depend on the material being cut. Heavy
growth will require slower action than will
light growth.
5. Never swing the unit so hard as you are in
danger of losing your balance or control of
the unit.
6. Try to control the cutting motion with the
hip rather than placing the full workload on
the arm and hands.
7. Take precautions to avoid wire, grass and
dead, dry, long-stem weeds from wrapping
around the head shaft. Such materials can
stall the head and cause the clutch to slip,
resulting in damage to the clutch system if
repeated frequently.
ADJUSTING THE LINE LENGTH
• Your brushcutters is equipped with a semiauto type nylon line head that allows the
operator to advance the line without
stopping the engine. When the line
becomes short, lightly tap the head on the
ground while running the engine at full
throttle.
• Each time the head is bumped, the line
advance about 1 inch(25.4 mm). For better
effect, tap the head on bear ground or hard
soil. Avoid bumping in thick, tall grass as
the engine may stall by overload.
❲ 14 ❳
Optional blade usage
OPT1
CUTTER
APPLICATION
CHART
Saw blade
8-teeth blade
4-teeth blade
Nylon line
head
6298-11313
10”
6298-15343
10”
6298-14343
10”
PT104 PT100
4”
6”
BC2300DL
BC2600DL
BC3400DL
BC4400DW
Under
growth
Heavy
weeds
Light
weeds
Grass
■ CHOOSE THE BLADE
Choose a suitable recommended cutting
attachment according to the object to be cut.
(OPT1)
• When replacing blade always be sure to use
products which have been certified by RedMax.
WARNING
• When sharpening, removing, or reattaching the
blade, be sure to wear thick, sturdy gloves and
use only proper tools and equipment to prevent
injury.
OPT2
FOR BC3400DL, BC4400DW
(1)
(2)
(3)
(4)
■ SET UP
1. Detach the line head assembly completely.
(OPT2)
2. Put on the blade, making the marked side face
the holder, put on the outer holders, and fasten
the blade with the blade nut. (OPT2)
(1) Bolt
: 3579-33260 (M8, LH)
(2) Spring washer : 3310-43210
(3) Plane washer : 01643-30823
(4) Cover
: 3520-13284
❲ 15 ❳
Optional blade usage
OPT3
IMPORTANT
FOR BC3400DL, BC4400DW
Change to the debris guard which is suitable for
the metal blade. (OPT3)
(1) Bolt
: 3540-24130 x 2 pieces
(2) Spring washer : 0290-20615 x 2 pieces
(3) Clamp
: 3541-24121
(4) Guard
: 3541-24112
(5) Guard ass’y
: 3541-24001
TIGHTENING TORQUE:
130~174 in-lbs
(14.7~19.6 N.m.)
OPT4
IMPORTANT
Change the loop handle to the J-handle for safe
operation. (OPT4)
(1) Bracket : 3532-14102
(2) J-handle : 6367-14200
FOR BC3400DL
■ STARTING ENGINE
Please refer to P.10 ■ STARTING ENGINE
WARNING
OPT5
• The product is equipped with a centrifugal
clutch mechanism, so the cutting attachment
begins to rotate as soon as the engine is
started by putting the throttle into the start
position. When starting the engine, place the
product onto the ground in a flat clear area
and hold it firmly in place so as to ensure that
neither the cutting part nor the throttle come
into contact with any obstacle when the
engine starts.
OPT6
■ CUTTING METHOD
a) Use the front left side cutting.
b) Guide the blade from your right to left with it
tilted slightly to your left. (OPT6)
c) When mowing a wide area, start working from
your left end to avoid interference of cut grass.
d) The blade may be seized by weeds if the engine
speed is too low, or the blade cuts too deep into
weeds. Adjust the engine speed and cutting
❲ 16 ❳
Optional blade usage
depth according to the condition of object.
WARNING
• If the grass or other object gets caught in the
blade, or if the unit starts to shake or vibrate,
turn off the engine and check the whole unit.
Change the blade if it has been damaged.
• Turn off the engine and make sure the blade has
completely stop before checking the blade, and
removing any object got caught in.
OPT7
■ OPERATION
1. Check the bolt to fasten the blade and be sure
the bolt has no fault, and no abrasion.
2. Be sure that the blade and the holder have been
fastened according to instruction and the blade
turns smoothly without abnormal noise. (OPT7)
WARNING
• The rotating parts fastened incorrectly may
cause serious accident to the operator.
• Make sure that the blade is not bent, warped,
cracked, broken or damaged.
• If you find any error to the blade, discard it
and change new one which is certified by
RedMax.
OPT8
■ By using the shoulder strap, hang the unit on
your right side. Adjust the strap length so that
the cutting head may become parallel to the
ground.(OPT8)
WARNING
Make sure to use shoulder strap and debris
guard. If not, it is vary dangerous when you slip
or lose your balance.
❲ 17 ❳
Optional blade usage
WARNING
■ CONTROLLING BLADE BOUNCE
• Kick out can cause serious personal injury.
Carefully study this section. It is important that
you understand what causes kick out, how you
can reduce the chance of kick out and how you
can remain in control of the unit if kick out does
occur.
1. What causes kick out:
• Kick out can occur when the moving blade
contacts an object that it cannot cut. This contact
causes the blade to stop for an instant and then
suddenly move or ”bounce” away from the object
that was hit. The operator can lose control of the
unit and the blade can cause serious personal
injury to the operator or any person nearby if the
blade contacts any part of the body.
2. How you can reduce the chance of kick out:
a. Recognize that kick out can happen. By
understanding and knowing about bounce,
you can help eliminate the element of
surprise.
b. Cut fibrous weeds and grass only. Do not
let the blade contact materials it cannot cut
such as hard, woody vines and brush or
rocks, fences, metal, etc
c. Be extra prepared for bounce if you must cut
where you cannot see the blade making
contact such as in areas of dense growth.
d. Keep the blade sharp. A dull blade increase
the chance of bounce.
e. Avoid feeding the blade too rapidly. The blade
can bounce away from material being cut if
the blade is fed faster than its cutting
capability.
f. Cut only from your right to your left.
g. Keep your path of advance clear of material
that has been cut and other debris.
❲ 18 ❳
Optional blade usage
3. How you can maintain the best control:
a. Keep a good, firm grip on the unit with both
hands. A firm grip can help neutralize bounce.
Keep your right and left hands completely
around the respective handles.
b. Keep both feet spread apart in a comfortable
stance and yet braced for the possibility that
the unit could bounce. Do not overreach.
Keep firm footing and balance.
OPT9
■ MAINTENANCE
BLADE
• Check the blade and the fasteners for
looseness, cracking, or bending.
• Check the cutting edges and reform with a flat
file.
Point (OPT8) :
1. Keep the end corner sharp.
2. Round the root of the edge, using round file.
3. Do not use water when using a grinder.
IMPORTANT
• It is recommended that filing should be done by
professionals.
• Especially regarding filing the saw blade, Leave
it to the professionals.
■ TRANSPORTING THE UNIT
• When you finish cutting in one location and wish
to continue work in another spot, turn off the
engine, and lift up the unit and carry it paying
attention fo the blade.
• Never forget to place the protective cover over
the blades.
• When transporting the unit over long distances,
detach the blade fix the unit by ropes.
❲ 19 ❳
Maintenance
WARNING
• Always be sure to stop the engine before
inspecting the brushcutter for problems
or performing maintenance.
• Never alter the brushcutter or take the
engine apart.
• When replacing parts, always be sure to
use only RedMax products or products
which have been certified by RedMax for
use with the RedMax brushcutter.
• Things to check before using
brushcutter
■ REFILLING TRIMMING LINE
1. For replacement line, use a diameter of
.095 in(2.4 mm). The spool is capable for a
line upto 27 ft(8 m)on the 4” head, and 46
ft(14m)on the 6” head. Avoid using a larger
line as it may cut down the trimming
performance. For safety reasons, do not
use metalreinforced line.
2. Pinch the slotted area on the both sides of
the spool housing to unhook the bottom
cap.
3. Take out the spool and pull off the old line.
Put one end of new line through the spool
holes and pull it until the length is equal
between each part of the line.
4. Wind up the line in the correct as indicated
on the spool.
❲ 20 ❳
5. Hook each end of the line in the slot on
the edge of the spool, and then put the
ends through the eyelets on the housing.
Make sure that the spring and the washers
are in place.
6. While holding the spool against the
housing, pull the line ends to release them
from the slot.
7. Line up the slot on the bottom cap with the
hook on the housing, press the cap
against the housing until it clicks.
WARNING
• Make sure that the engine has stopped
and is cool before performing any
service to the brushcutter. Contact with
moving cutting head or hot muffler may
result in a personal injury.
■ AIR FILTER
• The air filter, if clogged, will reduce the
engine performance. Monthly check and
clean the filter element in warm, soapy
water as required. Dry completely before
installing. If the element is broken or
shrunk, replace with a new one.
Maintenance
■ FUEL FILTER
• When the engine runs short of fuel supply,
check the fuel cap and the fuel filter for
blockage.
■ SPARK PLUG
• Starting failure and mis-firing are often
caused by a fouled spark plug. Periodically
clean the spark plug and check that the
spark gap is in the correct range. For a
replacement plug, use the correct type
specified by RedMax(See SPECIFICATIONS on the page 23).
• REPLACEMENT PLUG IS A CHAMPION
RCJ6Y OR THE EQUIVALENT, SUCH AS
BOSCH WSR8E OR NGK BPMR7A.
• Note that failing to do so may result in
the engine catching on fire.
■ SPARK ARRESTER
• The muffler is equipped with a spark
arrester to prevent red hot carbon from
flying out of the exhaust outlet. Periodically
inspect and clean as necessary with a wire
brush. In the State of California it is
required by law (Section 4442 of the
California Public Resources Code) to equip
a spark arrester when a gas powered tool
is used in any forest covered, brush
covered, or grass covered unimproved
land.
■ GEAR CASE
• The reduction gears are lubricated by
multipurpose, lithium-based grease in the
gear case. Supply new grease every 50
hours of use or more often depending on
the job condition.
IMPORTANT
• Note that using any spark plugs other than
those designated may result in the engine
failing to operate properly or in the engine
becoming overheated and damaged.
• To install the spark plug, first turn the plug
until it is finger tight, then tighten it a
quarter turn more with a socket wrench.
■ MUFFLER
WARNING
• Inspect periodically, the muffler for loose
fasteners, any damage or corrosion. If any
sign of exhaust leakage is found, do not
use the brushcutter and have it repaired
immediately.
❲ 21 ❳
Maintenance
■ INTAKE AIR COOLING VENT
WARNING
• Never touch the cylinder, muffler, or
spark plugs with your bare hands
immediately after stopping the engine.
The engine can become very hot when
in operation, and doing so could result
in severe burns.
• When checking the brushcutter to make
sure that it is okay before using it,
check the area around the muffler and
remove any wood chips or leaves which
have attached themselves to the
brushcutter. Note that failing to do so
could cause the muffler to become
overheated, and that this in turn could
cause the brushcutter to catch on fire.
Always make sure that the muffler is
clean and free of wood chips, leaves,
and other waste before use.
• Check the intake air cooling vent and the
area around the cylinder cooling fins after
every 25 hours of use for blockage, and
remove any waste which has attached itself
to the brushcutter. Note that it is necessary
to remove the plug guard shown in Figure
20 in order to be able to view the upper
part of the cylinder.
IMPORTANT
• If waste gets stuck and causes blockage
around the intake air cooling vent or
between the cylinder fins, it may cause the
engine to overheat, and that in turn may
cause mechanical failure on the part of the
brushcutter.
■ PROCEDURES TO BE PERFORMED
AFTER EVERY 100 HOURS OF USE
1. Remove the muffler, insert a screwdriver
into the vent, and wipe away any carbon
buildup. Wipe away any carbon buildup on
the muffler exhaust vent at the same time.
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has
worked its way in between the clutch lining
and drum, and if it has wipe it away using
oil-free, lead-free gasoline.
Storage
• Aged fuel is one of major causes of engine
starting failure. Before storing the unit,
empty the fuel tank and run the engine until
it uses all the fuel left in the fuel line and
the carburetor. Store the unit indoor taking
necessary measures for rust prevention.
❲ 22 ❳
Specifications
■ BC2300DL
Overall size(LxWxH) ····················································· 70.5x12.4x12.8(in) / 1790x315x325(mm)
Dry weight w/o acc. ··························································································· 9.5(lbs) / 4.75(kg)
Engine Type······················································································ Air-cooled 2-stroke gasoline
Model ·········································································································· Zenoah G23L
Displacement ······································································································· 22.5(cc)
Max. output ························································································· 1.0(HP)at 7500rpm
Fuel ························································································· Mixture(Gasoline 32:Oil 1)
Carburetor ··················································································· Walbro Diaphragm type
Spark plug ·····························································································Champion RCJ6Y
Fuel tank capacity ···························································································· 20.5(fl.oz) / 0.6( )
Transmission············································································ Centrifugal clutch,Rigid driveshaft
Reduction ratio ····················································································································· 1.357
Cutting head rotating direction ················································ Counter-clockwise(Operator view)
Standard Accessories
4 in. 2-line Head ········································································································ 1 pc.
Shoulder Strap ·········································································································· 1 pc.
Goggle ······················································································································· 1 pc.
Tool Kit ······················································································································ 1 pc.
■ BC2600DL
Overall size(LxWxH) ····················································· 71.7x12.4x13.2(in) / 1821x315x335(mm)
Dry weight w/o acc. ··························································································· 11.8(lbs) / 5.9(kg)
Engine Type······················································································ Air-cooled 2-stroke gasoline
Model ·········································································································· Zenoah G26L
Displacement ······································································································· 25.4(cc)
Max. output ························································································· 1.2(HP)at 7500rpm
Fuel ························································································· Mixture(Gasoline 32:Oil 1)
Carburetor ··················································································· Walbro Diaphragm type
Spark plug ···························································································· Champion RCJ6Y
Fuel tank capacity ···························································································· 25.0(fl.oz) / 0.7( )
Transmission············································································ Centrifugal clutch,Rigid driveshaft
Reduction ratio ····················································································································· 1.357
Cutting head rotating direction ················································ Counter-clockwise(Operator view)
Standard Accessories
4 in. 2-line Head ········································································································ 1 pc.
Shoulder Strap ·········································································································· 1 pc.
Goggle ······················································································································· 1 pc.
Tool Kit ······················································································································ 1 pc.
Specifications are subject to change without notice.
❲ 23 ❳
Specifications
■ BC3400DL
Overall size(LxWxH) ····················································· 67.7x12.6x13.6(in) / 1720x320x345(mm)
Dry weight w/o acc. ··························································································· 13.4(lbs) / 6.7(kg)
Engine Type······················································································ Air-cooled 2-stroke gasoline
Model ·········································································································· Zenoah G34L
Displacement ······································································································· 33.6(cc)
Max. output ························································································· 1.6(HP)at 7000rpm
Fuel ························································································· Mixture(Gasoline 32:Oil 1)
Carburetor ··················································································· Walbro Diaphragm type
Spark plug ···························································································· Champion RCJ6Y
Fuel tank capacity ···························································································· 25.0(fl.oz) / 0.7( )
Transmission············································································ Centrifugal clutch,Rigid driveshaft
Reduction ratio ····················································································································· 1.235
Cutting head rotating direction ················································ Counter-clockwise(Operator view)
Standard Accessories
6 in. 2-line Head ········································································································ 1 pc.
Shoulder Strap ·········································································································· 1 pc.
Goggle ······················································································································· 1 pc.
Tool Kit ······················································································································ 1 pc.
■ BC4400DW
Overall size(LxWxH) ····················································· 67.7x24.6x20.1(in) / 1720x625x510(mm)
Dry weight w/o acc. ······························································································ 16.0(lbs) / 8(kg)
Engine Type······················································································ Air-cooled 2-stroke gasoline
Model ·········································································································· Zenoah G43L
Displacement ······································································································· 41.5(cc)
Max. output ························································································· 2.0(HP)at 7000rpm
Fuel ························································································· Mixture(Gasoline 32:Oil 1)
Carburetor ··················································································· Walbro Diaphragm type
Spark plug ···························································································· Champion RCJ6Y
Fuel tank capacity ···························································································· 31.8(fl.oz) / 0.9( )
Transmission············································································ Centrifugal clutch,Rigid driveshaft
Reduction ratio ····················································································································· 1.235
Cutting head rotating direction ················································ Counter-clockwise(Operator view)
Standard Accessories
6 in. 2-line Head ········································································································ 1 pc.
Shoulder Strap ·········································································································· 1 pc.
Goggle ······················································································································· 1 pc.
Tool Kit ······················································································································ 1 pc.
Specifications are subject to change without notice.
❲ 24 ❳
Parts List
BRUSHCUTTERS
BC2300DL
BC2600DL
BC3400DL
BC4400DW
NOTE :
1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or
replacement.
2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the
use of any parts other than those specified by the company.
3. When placing parts orders for repair and/or replacement, check if the model name and the
serial number are applicable to those specified in the parts list, then use parts number
described in the parts list.
4. The contents described in the parts list may change due to improvement.
5. The parts for the machine shall be supplied seven (7) years after the machine is
discontinued. [It is possible that some specific parts may be subject to change of their
delivery term and list price within the limit of ten (7) years after the machine is
discontinued. It is also possible that some parts may be available even after the limit of
seven (7) years.]
APPLICABLE SERIAL NUMBERS :
BC2300DL
BC2600DL
BC3400DL
BC4400DW
DRIVE UNIT
DRIVE UNIT
DRIVE UNIT
DRIVE UNIT
500000000 and up
500000000 and up
980101 and up
980101 and up
Oct.1999
ENGINE UNIT
ENGINE UNIT
ENGINE UNIT
ENGINE UNIT
990639
978729
980101
980101
and up
and up
and up
and up
❲ 25 ❳
Parts List
Fig.1 DRIVE UNIT BC2300DL & BC2600DL
❲ 26 ❳
Fig.1 DRIVE UNIT BC2300DL & BC2600DL
Key#
Description
Part Number
Q'ty
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
HOUSING, ASS’Y
CUSHION
BRACKET (A)
BRACKET (B)
BOLT
BOLT
DRUM, clutch
SNAP, ring
BEARING
SNAP, ring
BOLT
HANGER COMP.
HANGER
CLAMP
SCREW
LEVER ASS'Y
THROTTLE LEVER
SCREW
SCREW
SPRING
STOP SWITCH
CORD, red
CORD, black
CABLE COMP.
GEARCASE ASS'Y
GEARCASE
BEARING
BEARING
BEARING
BEARING
GEAR
SHAFT
PINION
OIL SEAL
SNAP RING
SNAP RING
HOLDER(A)
HOLDER(B)
BOLT
WASHER
BOLT
BOLT
FITTING, grease
GUARD ASS'Y
GUARD COMP.
BLADE
SCREW
NUT
CLAMP
BOLT
WASHER
HANDLE ASS'Y
HANDLE
CLANP
SCREW
COM. TAP HEAD 4"
CASE
CORD HOLDER
COVER
PLATE, large
6460-11002
6470-31230
6460-31210
6460-31220
01252-30514
01252-30530
6460-12111
04065-02812
06004-06001
04064-01210
6468-91150
6460-17100
9366-17110
6460-17120
0263-90525
181124
181689
145569
180974
610314
180252
180768
180769
6502-82100
6460-13000
6460-13110
6460-13410
6460-13420
6460-13430
06001-06001
6460-13220
6460-13210
6460-13310
6460-13140
6460-13340
6460-13350
6460-13240
6460-13250
6460-13290
6460-13370
01252-50512
01252-50525
6460-13360
6460-24000
6460-24100
6041-24140
0263-30512
3320-15310
3541-24121
3540-24130
0290-20615
6462-14100
6462-14310
6462-14320
0263-90535
PT104
6460-15112
6460-15141
6460-15131
3268-15150
1
1
1
1
1
2
1
1
1
1
4
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
1
1
1
4
1
1
1
1
1
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Description
SPRING
PLATE, small
CORD
SPACER
SHAFT
GOGGLE
STRAP ASS'Y
TOOL KIT
SCREWDRIVER
SOCKET
WRENCH
BAR
SPANNER
PIPE COMP.
SHAFT
GRIP
DECAL
Part Number
Q'ty
6041-99161
3268-15170
6460-15180
6460-15210
PTA008
180773
160197
3550-91000
1030-91340
3239-91310
09007-00425
3540-91110
3540-91120
180771BC
3520-12212
180770
181127
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
❲ 27 ❳
Parts List
Fig.2 ENGINE UNIT BC2300DL
❲ 28 ❳
Fig.2 ENGINE UNIT BC2300DL
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Description
CYLINDER
GASKET,base
BOLT
INSULATOR
GASKET,insulator
GASKET,carburetor
SCREW
MUFFLER ASS'Y
––––––
ARRESTER
BOLT
GASKET,muffler
PLATE,muffler
SCREW
CRANKCASE COMP.
GASKET,case
BEARING
OIL SEAL
OIL SEAL
SNAP RING
SCREW
PISTON
RING
PIN
SNAP RING
BEARING
WASHER
CRANKSHAFT COMP.
NUT
KEY
SHOE,clutch
SCREW
SPRING
WASHER
WASHER
ROTOR
COIL ASS'Y
CORD
CAP
CAP
SPRING
GROMMET
SPACER
BOLT
RECOIL ASS'Y
CASE COMP.
REEL
SPRING,spiral
SCREW
ROPE
KNOB
PLATE,stopper
PULLEY ASS'Y
RATCHET
SPRING
SCREW
CARBURETOR ASS'Y
SCREW
BRACKET
RING
Part Number
Q'ty
Key#
Description
5580-12110
5500-12212
1850-12130
5500-13162
5500-13121
5500-13131
0263-90520
5850-15100
–––––
1601-15120
01252-30550
5910-15211
5500-15220
0263-90416
5500-21100
5500-21141
06030-06001
2169-21210
1850-21220
04065-02812
01252-30530
5600-41111
1100-41210
1101-41310
1260-41320
1140-41330
1101-41340
5500-42001
1650-43230
1000-43240
1140-51111
1140-51250
1970-51221
1140-51230
1970-51241
5501-71110
5501-71201
5500-71220
2616-71320
1900-72111
1900-72120
5500-72130
1260-71261
3310-72150
5500-75100
5500-75110
1850-75120
1850-75130
1850-75151
1850-75160
1140-75320
5500-75170
1850-75201
1850-75221
1850-75230
0263-90416
5501-81000
1752-81110
5500-81120
1751-81130
1
1
2
1
1
1
2
1
–
1
2
1
1
1
1
1
2
1
1
1
4
1
2
1
2
1
2
1
1
1
2
2
1
2
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
1
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
SWIVEL
VALVE ASS'Y
SCREW,adjuster
NUT,adjuster
RING
O-RING
JET
DIAPHRAGM
GASKET,pump
DIAPHRAGM,pump
BODY ASS'Y
SCREEN
GASKET,diaphragm
BODY,purge
PUMP,priming
COVER,pump
SCREW
WASHER
SCREW
BODY ASS'Y
SLEEVE
PLATE,choke
LEVER,choke
SCREW
ELEMENT
COVER ASS'Y
KNOB
COVER,fan
SCREW
COVER,engine
SCREW
SCREW
GUARD,plug
SCREW
SPARKPLUG
GROMMET
CORD COMP.
TANK ASS'Y
CAP ASS'Y
HOLDER
CAP,holder
VALVE
PACKING
PIPE COMP.
FILTER ASS'Y
CLIP
SCREW
CLIP
LABEL
RING
VALVE
SPRING
SCREW
PIN
LEVER
PIN
Part Number
1881-81140
–––––
1918-81170
1751-81180
1881-81130
1751-81240
5500-81251
3310-81260
1065-81410
1065-81420
1850-81450
3306-81380
1850-81470
1850-81490
1751-81510
1850-81520
1850-81530
5500-81160
0263-90560
5500-82102
1970-82190
5500-82131
5500-82140
2630-33610
5500-82171
5600-82202
5500-82221
5501-31111
0263-90520
5580-32112
1850-32160
1900-31410
5500-32210
0263-90514
5602-73110
1852-72121
5501-73201
5500-85004
5601-85200
5601-85230
5600-85240
5600-85250
5500-85220
5500-85300
5500-85400
1260-85460
5500-85510
1950-86120
5501-91122
5500-82230
3356-81310
1850-81270
1850-81220
3310-81250
3310-81230
2629-21130
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
2
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
3
❲ 29 ❳
Parts List
Fig.3 ENGINE UNIT BC2600DL
❲ 30 ❳
Fig.3 ENGINE UNIT BC2600DL
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Description
CYLINDER
GASKET,base
BOLT
INSULATOR
GASKET,insulator
GASKET,carburetor
SCREW
MUFFLER ASS'Y
––––––
ARRESTER
BOLT
GASKET,muffler
PLATE,muffler
SCREW
CRANKCASE COMP.
GASKET,case
BEARING
OIL SEAL
OIL SEAL
SNAP RING
SCREW
PISTON
RING
PIN
SNAP RING
BEARING
WASHER
CRANKSHAFT COMP.
NUT
KEY
SHOE,clutch
SCREW
SPRING
WASHER
WASHER
ROTOR
COIL ASS'Y
CORD
CAP
CAP,plug
SPRING
GROMMET
SPACER
BOLT
RECOIL ASS'Y
CASE COMP.
REEL
SPRING,spiral
SCREW
ROPE
KNOB
PLATE,stopper
PULLEY ASS'Y
RATCHET
SPRING
SCREW
CARBURETOR ASS'Y
SCREW
BRACKET
RING
Part Number
Q'ty
Key#
Description
5911-12110
5500-12212
1850-12130
1920-13162
5500-13121
5500-13131
0263-90520
5850-15100
–––––
1601-15120
01252-30550
5910-15211
5500-15220
0263-90416
5500-21100
5500-21141
06030-06001
2169-21210
1850-21220
04065-02812
01252-30530
5910-41110
5910-41210
1600-41310
1260-41320
1140-41330
1101-41340
5500-42001
1650-43230
1000-43240
1140-51111
1140-51250
1970-51221
1140-51230
1970-51241
5501-71110
5501-71201
5500-71220
2616-71320
1900-72111
1900-72120
5500-72130
1260-71261
3310-72150
5500-75100
5500-75110
1850-75120
1850-75130
1850-75151
1850-75160
1140-75320
5500-75170
1850-75201
1850-75221
1850-75230
0263-90416
5911-81000
1752-81110
5500-81120
1751-81130
1
1
2
1
1
1
2
1
–
1
2
1
1
1
1
1
2
1
1
1
4
1
2
1
2
1
2
1
1
1
2
2
1
2
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
1
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
SWIVEL
VALVE ASS'Y
SCREW,adjuster
NUT,adjuster
RING
O-RING
JET
DIAPHRAGM
GASKET,pump
DIAPHRAGM,pump
BODY ASS'Y
SCREEN
GASKET,diaphragm
BODY,purge
PUMP,priming
COVER,pump
SCREW
WASHER
SCREW
BODY ASS'Y
SLEEVE
PLATE,choke
LEVER,choke
SCREW
ELEMENT
COVER ASS'Y
KNOB
COVER,fan
SCREW
COVER,engine
SCREW
SCREW
GUARD,plug
SCREW
SPARKPLUG
GROMMET
CORD COMP.
TANK ASS'Y
CAP ASS'Y
HOLDER
CAP,holder
VALVE
PACKING
PIPE COMP.
FILTER ASS'Y
CLIP
SCREW
SCREW
CLIP
LABEL
STAND
RING
VALVE
SPRING
SCREW
PIN
LEVER
PIN
Part Number
1881-81140
–––––
1918-81170
1751-81180
1881-81130
1751-81240
5500-81251
3310-81260
1065-81410
1065-81420
1850-81450
3306-81380
1850-81470
1850-81490
1751-81510
1850-81520
1850-81530
5500-81160
0263-30555
5500-82102
1970-82190
5500-82131
5500-82140
2630-33610
5500-82171
5600-82202
5500-82221
5501-31111
0263-90520
5580-32112
1850-32160
1900-31410
5500-32210
0263-90514
5602-73110
1852-72121
5501-73201
5911-85002
5601-85200
5601-85230
5600-85240
5600-85250
5500-85220
5911-85300
5500-85400
1260-85460
5500-85510
5910-85510
1950-86120
5911-91121
1897-31911
5500-82230
3356-81310
1850-81270
1850-81220
3310-81250
3310-81230
2629-21130
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
2
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
3
❲ 31 ❳
Parts List
Fig.4 DRIVE UNIT BC3400DL (S/N 980101 and up)
❲ 32 ❳
Fig.4 DRIVE UNIT BC3400DL (S/N 980101 and up)
Key#
Description
Part Number
Q'ty
Key#
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
HOUSING
CAP
JOINT
ABSORBER-F
ABSORBER-R
BOLT
BOLT
BOLT
DRUM,clutch
BEARING
SNAPRING
SNAPRING
BOLT
PIPE COMP
GRIP
DRIVE SHAFT
HANGER ASSY
• HANGER
• CLAMP
• SPACER
• SCREW
LEVER ASSY
CORD(A),black
CORD(B),red
CABLE COMP
TUBE
GEARCASE ASSY
• GEARCASE
• BEARING
• BEARING
• SEAL
• SNAPRING
• BOLT
• FITTING,grease
• WASHER
• SHAFT
• GEAR
• WASHER
• WASHER
• BOLT,LH
• PINION
• BEARING
• BEARING
• SNAPRING
• SNAPRING
• BOLT
• HOLDER(A)
• HOLDER(B)
HANDLE ASSY
• HANDLE
• CLAMP
• SCREW
GUARD ASSY
• GUARD COMP
• • BLADE
• • NUT
• • SCREW
• CLAMP
• BOLT
• WASHER
4050-11110
4050-11150
4050-11210
4050-11250
4050-11260
01252-30530
01252-30630
01252-30510
4050-11310
06004-06202
04065-03515
04064-01510
6468-91150
4001-12100
3577-32140
4050-12210
6520-17100
6520-17110
6520-17120
6520-17130
0263-90525
6232-12400
T3003-14420
T3003-14430
1855-82100
T3003-14510
T3003-13000
3541-13114
06000-06000
06000-06201
3180-13141
04065-03212
01252-30510
3199-13350
01641-20608
4050-13210
3180-13220
3310-43210
01643-30823
3579-33260
3541-13311
06001-06000
06000-06000
3180-13330
04065-02612
3540-13260
3541-13241
3541-13251
6462-14100
6462-14310
6462-14320
0263-90535
6358-24002
6538-24102
6041-24140
3320-15310
0263-30512
3541-24121
3540-24130
0290-20615
1
1
1
1
1
4
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
2
2
1
2
2
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
SHAFT
COM.TAP.HEAD 6"
• CASE
• CORD HOLDER
• COVER
• PLATE
• SPRING
• PLATE
• CORD
• SPACER
HARNESS ASSY
• HOOK
• PLATE
• HANGER COMP
• BAND
• PROTECTOR
TOOL SET
SCREW DRIVER
SOCKET
WRENCH
WRENCH
BAR
SPANNER
GOGGLE
Part Number
6041-99220
PT100
6041-99111
6041-99140
6041-99130
3268-15150
6041-99161
3268-15170
6041-99181
6460-15210
6565-95200
6565-17210
6565-17220
6565-95230
6565-17200-01
6565-17200-02
3532-91000
1030-91340
3239-91310
09007-00425
09007-00528
3540-91110
3540-91120
6242-92110
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
❲ 33 ❳
Parts List
Fig.5 ENGINE UNIT BC3400DL (S/N 980101 and up)
❲ 34 ❳
Fig.5 ENGINE UNIT BC3400DL (S/N 980101 and up)
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Description
CYLINDER
BOLT
GASKET,base
CRANKCASE COMP.
• PIN
GASKET,case
BEARING
OIL SEAL
OIL SEAL
BOLT
SNAP RING
PISTON
RING
PIN
RING
BEARING
WASHER
CRANKSHAFT COMP.
SHOE,clutch
SPRING
SCREW
WASHER
WASHER
ROTOR
COIL ASS'Y
• CORD
• CAP
• PIN
GROMMET
CAP,plug
SPRING
BOLT
NUT
KEY
MUFFLER ASS'Y
• ARRESTER
BOLT
BOLT
GASKET
PLATE
SCREW
COVER
BOLT
PLATE
COVER
SCREW
GUARD
SPARKPLUG
GROMMET
CORD
CORD,earth
CLAMP
RECOIL ASS'Y
• REEL
• SCREW
• SPRING,spiral
• COLLAR
• ARM
• ROPE
• KNOB
Part Number
Q'ty
Key#
4700-12110
3310-12281
4500-13120
4500-21100
2629-21130
4500-21140
06030-06201
4810-21210
1650-21220
01252-30530
04065-03212
4700-41110
1650-41210
1030-41310
1300-41320
T2100-41410
2850-41510
4500-42000
1400-51111
1651-51220
1200-51211
1200-51230
1200-51241
4700-71110
4700-71200
4700-71220
4700-71230
4700-71240
5500-72130
1900-72111
1900-72120
4500-72150
1650-43230
1000-43240
T1006-15100
1601-15120
01252-30560
3310-31720
4700-15210
4500-15220
0263-90514
4700-31110
3310-12281
4700-31210
4500-32110
4500-32120
4500-32210
5602-73110
1852-72121
T1006-73220
T1006-73230
1140-72231
4500-75100
4500-75120
4500-75150
1850-75130
4500-75180
4500-75190
4500-75160
1140-75320
1
4
1
1
3
1
2
1
1
4
1
1
2
1
2
1
2
1
2
1
2
2
2
1
1
1
1
2
1
1
1
2
1
1
1
1
2
1
1
1
1
1
4
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
Description
Part Number
• PLATE,stopper
5500-75170
PULLEY
4500-75210
SCREW
4500-75511
COLLAR
4700-75310
INSULATOR
4500-13160
SCREW
4500-13180
GASKET,insulator
4700-13150
GASKET,carburetor
4500-13130
CARBURETOR ASS'Y
T1006-81000
• REBUILT KIT
5602-06030
• • BODY ASS'Y
1850-81450
• • • SCREEN
–––––––––
• • • VALVE
–––––––––
• • • SPRING
–––––––––
• • • SCREW
–––––––––
• • • PIN
–––––––––
• • • LEVER
–––––––––
• • GASKET KIT
5602-06020
• • • DIAPHRAGM
–––––––––
• • • GASKET,diaphragm
–––––––––
• • • DIAPHRAGM,pump
–––––––––
• • • GASKET,pump
–––––––––
• BODY,purge
1850-81490
• COVER,pump
1850-81520
• PUMP,priming
1751-81510
• JET
T1006-81250
• O-RING
1751-81240
• RING
1751-81130
• SWIVEL
1881-81140
• VALVE ASS'Y
–––––––––
• SCREW
1752-81110
• BRACKET
5500-81120
• NUT,adjuster
1751-81180
• SCREW,adjuster
1918-81170
• RING
1881-81130
• SCREW
1850-81530
• WASHER
5500-81160
SCREW
0263-30550
BODY ASS'Y
4500-82100
PLATE,choke
4500-82130
LEVER,choke
4500-82140
SCREW
2630-33610
ELEMENT
4500-82170
SCREEN
4500-82180
COVER ASS'Y
4500-82200
KNOB
5500-82221
RING
5500-82230
TANK ASS'Y
4700-85000
• CAP ASS'Y
4500-85200
• • HOLDER
4500-85230
• • CAP
5600-85240
• • VALVE
5600-85250
• • PACKING
4500-85220
• PIPE COMP.
5500-85300
• FILTER ASS'Y
3302-85400
• CLIP
1260-85460
SCREW
1600-86120
LABEL,recoil
T1006-75410
Q'ty
1
1
4
1
1
2
1
1
1
1
1
–
–
–
–
–
–
1
–
–
–
–
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
❲ 35 ❳
Parts List
Fig.6 DRIVE UNIT BC4400DW (S/N 980101 and up)
❲ 36 ❳
Fig.6 DRIVE UNIT BC4400DW (S/N 980101 and up)
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Description
HOUSING
CAP
JOINT
ABSORBER-F
ABSORBER-R
BOLT
BOLT
BOLT
DRUM,clutch
BEARING
SNAPRING
SNAPRING
BOLT
PIPE COMP
DRIVE SHAFT
HANGER ASSY
• HANGER
• CLAMP
• SPACER
• SCREW
BRACKET ASSY
• BRACKET
• ABSORBER
• CAP,Upper
• CAP,Lower
• CLAMP(A)
• CLAMP(B)
• BOLT
• BOLT
• BOLT
HANDLE COMP,Left
• GRIP
LEVER ASSY
CORD(A),black
CORD(B),red
CABLE COMP
TUBE
HANDLE COMP,Right
• GRIP
BAND
CLAMP
SCREW
GEARCASE ASSY
• GEARCASE
• BEARING
• BEARING
• SEAL
• SNAPRING
• BOLT
• FITTING,grease
• WASHER
• SHAFT
• GEAR
• WASHER
• WASHER
• BOLT,LH
• PINION
• BEARING
• BEARING
• SNAPRING
Part Number
Q'ty
Key#
Description
4050-11110
4050-11150
4050-11210
4050-11250
4050-11260
01252-30530
01252-30630
01252-30510
4050-11310
06004-06202
04065-03515
04064-01510
6468-91150
4050-12100
3540-12211
6520-17100
6520-17110
6520-17120
6520-17130
0263-90525
4050-14101
4050-14111
4050-14140
3257-14192
4050-14121
4050-14150
4050-14160
01252-30525
01252-30535
01252-30514
3540-14200
3540-14220
6234-14601
T3004-14710
T3004-14720
5915-83100
T3004-14810
6242-14400
3540-14321
3540-93120
3260-14251
0260-00516
T3003-13000
3541-13114
06000-06000
06000-06201
3180-13141
04065-03212
01252-30510
3199-13350
01641-20608
4050-13210
3180-13220
3310-43210
01643-30823
3579-33260
3541-13311
06001-06000
06000-06000
3180-13330
1
1
1
1
1
4
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
• SNAPRING
• BOLT
• HOLDER(A)
• HOLDER(B)
GUARD ASSY
• GUARD COMP
• • BLADE
• • NUT
• • SCREW
• CLAMP
• BOLT
• WASHER
SHAFT
COM.TAP.HEAD 6"
• CASE
• CORD HOLDER
• COVER
• PLATE
• SPRING
• PLATE
• CORD
• SPACER
PROTECTOR
HARNESS ASSY
• HOOK
• PLATE
• HANGER COMP
• BAND
• PROTECTOR
TOOL SET
• SCREW DRIVER
• SOCKET
• WRENCH
• WRENCH
• BAR
• SPANNER
GOGGLE
Part Number
04065-02612
3540-13260
3541-13241
3541-13251
6359-24000
6359-24100
6357-24150
3320-15310
0263-30512
3541-24121
3540-24130
0290-20615
6041-99220
PT100
6041-99111
6041-99140
6041-99130
3268-15150
6041-99161
3268-15170
6041-99181
6460-15210
4050-17110
6565-95200
6565-17210
6565-17220
6565-95230
6565-17200-01
6565-17200-02
3532-91000
1030-91340
3239-91310
09007-00425
09007-00528
3540-91110
3540-91120
6242-92110
Q'ty
1
1
1
1
1
1
1
2
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
❲ 37 ❳
Parts List
Fig.7 ENGINE UNIT BC4400DW (S/N 980101 and up)
❲ 38 ❳
Fig.7 ENGINE UNIT BC4400DW (S/N 980101 and up)
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Description
CYLINDER
BOLT
GASKET,base
CRANKCASE COMP.
• PIN
GASKET,case
BEARING
OIL SEAL
OIL SEAL
BOLT
SNAP RING
PISTON
RING
PIN
RING
BEARING
WASHER
CRANKSHAFT COMP.
SHOE,clutch
SPRING
SCREW
WASHER
WASHER
ROTOR
COIL ASS'Y
• CORD
• CAP
• PIN
GROMMET
CAP,plug
SPRING
BOLT
NUT
KEY
MUFFLER ASS'Y
• ARRESTER
BOLT
BOLT
GASKET,muffler
PLATE,muffler
SCREW
COVER
BOLT
PLATE
COVER
SCREW
GUARD
SPARKPLUG
GROMMET
CORD COMP.
CLAMP
RECOIL ASS'Y
• REEL
• SCREW
• SPRING,spiral
• COLLAR
• ARM
• ROPE
• KNOB
• PLATE,stopper
Part Number
Q'ty
Key#
4500-12110
3310-12281
4500-13120
4500-21100
2629-21130
4500-21140
06030-06201
4810-21210
1650-21220
01252-30530
04065-03212
4500-41110
1400-41220
2850-41310
1300-41320
T2100-41410
2850-41510
4500-42000
4500-51110
4500-51220
1200-51211
1200-51230
1200-51241
4500-71110
4500-71200
4500-71220
2616-71320
3356-21130
5500-72130
1900-72111
1900-72120
4500-72150
1650-43230
1000-43240
T1007-15100
1601-15120
01252-30565
3310-31720
4700-15210
4500-15220
0263-90514
4500-31110
3310-12281
4500-31210
4500-32110
4500-32120
4500-32210
5602-73110
1852-72121
T1007-73200
1140-72231
4500-75100
4500-75120
4500-75150
1850-75130
4500-75180
4500-75190
4500-75160
1140-75320
5500-75170
1
4
1
1
3
1
2
1
1
4
1
1
2
1
2
1
2
1
2
1
2
2
2
1
1
1
1
2
1
1
1
2
1
1
1
1
2
1
1
1
1
1
4
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
Description
PULLEY
SCREW
PLATE
WASHER
INSULATOR
SCREW
GASKET,insulator
GASKET,carburetor
CARBURETOR ASS'Y
• REBUILT KIT
• • BODY ASS'Y
• • • SCREEN
• • • VALVE
• • • SPRING
• • • SCREW
• • • PIN
• • • LEVER
• • GASKET KIT
• • • DIAPHRAGM
• • • GASKET,diaphragm
• • • DIAPHRAGM,pump
• • • GASKET,pump
• BODY,purge
• COVER,pump
• PUMP,priming
• JET
• O-RING
• RING
• SWIVEL
• VALVE ASS'Y
• SCREW
• BRACKET
• NUT,adjuster
• SCREW,adjuster
• RING
• SCREW
• WASHER
SCREW
BODY ASS'Y
• PLATE,choke
• LEVER,choke
• SCREW
ELEMENT
SCREEN
COVER ASS'Y
• KNOB
• RING
TANK ASS'Y
• CAP ASS'Y
• • HOLDER
• • CAP
• • VALVE
• • PACKING
• PIPE COMP.
• FILTER ASS'Y
• CLIP
SCREW
LABEL
Part Number
Q'ty
4500-75210
4500-75511
4500-75310
01643-20823
4500-13160
4500-13180
4500-13150
4500-13130
T1007-81000
5602-06030
1850-81450
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
5602-06020
–––––––––
–––––––––
–––––––––
–––––––––
1850-81490
1850-81520
1751-81510
T1007-81250
1751-81240
1751-81130
1881-81140
–––––––––
1752-81110
5500-81120
1751-81180
1918-81170
1881-81130
1850-81530
5500-81160
0263-30550
4500-82100
4500-82130
4500-82140
2630-33610
4500-82170
4500-82180
4500-82200
5500-82221
5500-82230
4500-85000
4500-85200
4500-85230
5600-85240
5600-85250
4500-85220
5500-85300
3302-85400
1260-85460
1600-86120
T1007-75410
1
4
1
1
1
2
1
1
1
1
1
–
–
–
–
–
–
1
–
–
–
–
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
❲ 39 ❳
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO
EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND
GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN
EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S
STRINGENT ANTI-SMOG STANDARDS.
KOMATSU ZENOAH Co, MUST WARRANT THE EMISSION CONTROL SYSTEM ON YOUR LAWN AND
GARDEN EQUIPMENT ENGINE FOR THE PERIODS OF TIME LISTED BELOW PROVIDED THERE HAS
BEEN NO ABUSE, NEGLECT OR IMPROPER MAINTENANCE OF YOUR LAWN AND GARDEN
EQUIPMENT ENGINE.
YOUR EMISSION CONTROL SYSTEM. MAY INCLUDE PARTS SUCH AS THE CARBURETOR, THE
IGNITION SYSTEM, AND CATALYTIC CONVERTER. ALSO INCLUDED MAY BE THE HOSES, BELTS,
CONNECTORS AND OTHER EMISSION-RELATED ASSEMBLIES.
WHERE A WARRANTABLE CONDITION EXISTS, KOMATSU ZENOAH Co. WILL REPAIR YOUR LAWN
AND GARDEN EQUIPMENT ENGINE AT NO COST TO YOU INCLUDING DIAGNOSIS, PARTS AND
LABOR.
MANUFACTURER'S WARRANTY COVERAGE:
THE 1995 AND LATER UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES ARE
WARRANTED FOR TWO YEARS. IF ANY EMISSION-RELATED PART ON YOUR ENGINE IS
DEFECTIVE, THE PART WILL BE REPAIRED OR REPLACED BY KOMATSU ZENOAH Co.
OWNER'S WARRANTY RESPONSIBILITIES:
—AS THE LAWN AND GARDEN EQUIPMENT ENGINE OWNER, YOU ARE RESPONSIBLE FOR
THE PERFORMANCE OF THE REQUIRED MAINTENANCE LISTED IN YOUR OWNER'S
MANUAL. KOMATSU ZENOAH Co. RECOMMENDS THAT YOU RETAIN ALL RECEIPTS
COVERING MAINTENANCE ON YOUR LAWN AND GARDEN ENGINE, BUT KOMATSU
ZENOAH Co. CAN NOT DENY WARRANTY SOLELY FOR THE LACK OF RECEIPTS OR FOR
YOUR FAILURE TO ENSURE THE PERFORMANCE OF ALL SCHEDULED MAINTENANCE.
—AS THE LAWN AND GARDEN EQUIPMENT ENGINE OWNER, YOU SHOULD BE AWARE,
HOWEVER, THAT KOMATSU ZENOAH Co. MAY DENY YOU WARRANTY COVERAGE IF
YOUR LAWN AND GARDEN EQUIPMENT ENGINE OR A PART HAS FAILED DUE TO ABUSE,
NEGLECT, IMPROPER MAINTENANCE OR UNAPPROVED MODIFICATION.
—YOU ARE RESPONSIBLE FOR PRESENTING YOUR LAWN AND GARDEN EQUIPMENT
ENGINE TO A KOMATSU ZENOAH Co. DISTRIBUTION CENTER AS SOON AS A PROBLEM
EXISTS. THE WARRANTY REPAIRS SHOULD BE COMPLETED IN A REASONABLE AMOUNT
OF TIME, NOT TO EXCEED 30 DAYS.
IF YOU HAVE ANY QUESTIONS REGARDING YOU WARRANTY RIGHTS AND RESPONSIBILITIES,
YOU SHOULD CONTACT KOMATSU ZENOAH AMERICA INC. AT (770)-381-5147.
Red Max TRIMMER/BRUSHCUTTER
MODEL BC2300DL/BC2600DL/BC3400DL/BC4400DW
2-YEAR LIMITED WARRANTY
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL
BC2300DL, BC2600DL, BC3400DL OR BC4400DW UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY),
THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH
SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR
WORKMANSHIP. EMISSION-RELATED PARTS ARE:
THE CARBURETOR ASSY, COIL ASSY, ROTOR, SPARKPLUG,
AIR FILTER, FUEL FILTER, INTAKE MANIFOLD, AND THE GASKETS
ALL OTHER PARTS EXCEPT ABOVE PARTS, FOR TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER
USE ] FROM THE DATE OF ORIGINAL ANY DELIVERY OF THE MODEL BC2300DL, BC2600DL, BC3400DL OR
BC4400DW UNIT, THE COMPANY, THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF
CHARGE, FOR THE ORIGINAL PURCHASER, ANY PART OF PARTS FOUND TO BE DEFECTIVE IN MATERIAL
AND/OR WORKMANSHIP. THIS IS THE EXCLUSIVE REMEDY.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF "REPAIR OR REPLACE AS
NECESSARY" SHALL BE WARRANTED FOR THE WARRANTY PERIOD.ANY WARRANTED PART WHICH IS
SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF
TIME UP TO THE FIRST SCHEDULED REPLACEMNET POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NONWARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A
WARRANTED PARTS STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF
INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS,
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBULICATION, USE OF ANY PARTS OR ACCESSARIES
OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE CONPANY'S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED TO TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER USE ] FROM THE ORIGINAL
DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES
ARE EXCLUDED.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMINATION OR EXCLUSION MAY
NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL KOMATSU
ZENOAH AMERICA INC. AT (770)-381-5147.
IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL
OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP
A COPY FOR YOUR RECORDS.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
Débroussailleuse à deux lames réciproques
Modèle BC2300DL/BC2600DL/BC3400DL/BC4400DW
Garantie limitée à 2 ans
Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par
l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour
l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage
défectueux pendant deux (2) ans à compter de la date initiale de livraison d’une unité du modèle
BC2300DL/BC2600DL/BC3400DL/BC4400DW. Les pièces en rapport avec les émissions de gaz d'échappement
sont:
l'assemblage carburateur, l'assemblage bobine, le rotor, la bougie, le filtre à air,
le filtre à carburant, la tubulure d'admission et les joints
Toutes autres pièces exceptées celles mentionnées ci-dessus : La société, par l'intermédiaire de n'importe quel
revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial toute(s) pièce (s) se
révélant de constitution et/ou de montage défectueux pendant deux (2) ans en cas d’utilisation privée [un (1) an pour
toute autre utilisation] à compter de la date de livraison initiale d’une unité du modèle
BC2300DL/BC2600DL/BC3400DL/BC4400DW. Telles sont les limites de la garantie.
Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge de l'acheteur.
L'acheteur ne supportera pas le coût de main d'oeuvre du diagnostic qui amène à la conclusion qu'une pièce
garantie est défectueuse, si ce diagnostic est effectué chez le revendeur RedMax.
L’acheteur ou propriétaire a pour responsabilité d’effectuer l’entretien obligatoire tel que défini par le fabricant dans le
manuel du propriétaire/de l'utilisateur.
Toute pièce garantie dont le remplacement n'est pas prévu dans le cadre de l’entretien obligatoire, ou pour laquelle
est seulement prévue une inspection périodique pour "remplacement ou réparation si nécessaire" sera garantie pour
la période de garantie. Toute pièce garantie arrivée à l’échéance de son premier remplacement prévu sera garantie
jusqu’à celui-ci.
Toute pièce de rechange équivalente en performance ou en durabilité peut être utilisée pour l’entretien hors-garantie
ou les réparations hors-garantie, et ce sans réduire l’obligation de garantie incombant à la société.
La société sera tenue responsable des dommages aux autres composants du moteur causés par la défaillance de
pièce(s) garantie(s) en période de garantie.
La garantie ne s'applique pas aux unités endommagées par suite de: négligence dans la mise en oeuvre des
instructions spécifiées dans le manuel du propriétaire/de l'utilisateur en vue d’une utilisation et d’un entretien correct,
fausse manœuvre accidentelle, modification, utilisation abusive, lubrification incorrecte, utilisation de pièces ou
d’accessoires autres que ceux spécifiés par la société, ou autres causes hors du contrôle de la société.
Cette garantie ne couvre pas les pièces remplacées en raison de leur usure normale ou de changements
d’apparence sans effets.
Il n'existe aucune autre garantie explicite.
Les garanties implicites, celles de négociabilité du produit et de son adaptabilité à un usage défini incluses, sont
limitées à deux (2) ans pour un usage privé [un (1) an pour toute autre utilisation] à compter de la date initiale de
livraison.
Les responsabilités pour les dommage conséquents ou incidents sont exclues de toutes les garanties.
Certaines provinces n'autorisant pas les limitations à la durée des garanties implicites, ou les exclusions ou
limitations relatives aux dommages incidents ou conséquents, la limitation indiquée ci-dessus peut ne pas vous être
applicable.
Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits variant
d'une province à l'autre.
Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez appeler KOMATSU
ZENOAH AMERICA INC. au (770)-381-5147
Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et
l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie
pour vous.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
EMISSION CONTROL LABEL
BC2300DL
IMPORTANT ENGINE INFORMATION
THIS ENGINE CONFORMS TO US EPA
PH1 AND 1995-1998 CALIFORNIA EMISSION
REGULATIONS FOR ULGE ENGINES.
ENGINE FAMILY : TKZ025UB24RA
ENGINE DISPLACEMENT : 22.5cc
REFER TO OWNER'S MANUMAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
RedMax
Made in Japan
INFORMATION IMPORTANTE
CONCERNANT LE MOTEUR
Ce moteur conformc aux normcs U.S. EPA PH1 et
1995-1998 de la régulementation concernant la
pollution de l'air pour les petits moteurs tout-terrain.
Type de moteur : TKZ025UB24RA
Cylindrée du moteur : 22,5 cc
Se référer au Manuel de l'utilisateur pour
les spécifications d'entretien et les réglages.
RedMax
Made in Japan
BC2600DL
IMPORTANT ENGINE INFORMATION
THIS ENGINE CONFORMS TO US EPA
PH1 AND 1995-1998 CALIFORNIA EMISSION
REGULATIONS FOR ULGE ENGINES.
ENGINE FAMILY : TKZ025UB24RA
ENGINE DISPLACEMENT : 25.4cc
REFER TO OWNER'S MANUMAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
RedMax
Made in Japan
INFORMATION IMPORTANTE
CONCERNANT LE MOTEUR
Ce moteur conformc aux normcs U.S. EPA PH1 et
1995-1998 de la régulementation concernant la
pollution de l'air pour les petits moteurs tout-terrain.
Type de moteur : TKZ025UB24RA
Cylindrée du moteur : 25,4 cc
Se référer au Manuel de l'utilisateur pour
les spécifications d'entretien et les réglages.
RedMax
Made in Japan
BC3400DL
IMPORTANT
ENGINE INFORMATION
THIS ENGINE CONFORMS TO US EPA
PH1 AND 1995-1999 CALIFORNIA EMISSION
REGULATIONS FOR ULGE ENGINES.
ENGINE FAMILY : XKZXS.0344UV;EM
ENGINE DISPLACEMENT : 33.6cc
REFER TO OWNER'S MANUMAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
RedMax
Made in Japan
INFORMATION IMPORTANTE
CONCERNANT LE MOTEUR
Ce moteur conformc aux normcs U.S. EPA PH1 et
1995-1999 de la régulementation concernant la
pollution de l'air pour les petits moteurs tout-terrain.
Type de moteur : XKZXS.0344UV;EM
Cylindrée du moteur : 33,6 cc
Se référer au Manuel de l'utilisateur pour
les spécifications d'entretien et les réglages.
RedMax
Made in Japan
BC4400DW
IMPORTANT
ENGINE INFORMATION
THIS ENGINE CONFORMS TO US EPA
PH1 AND 1995-1999 CALIFORNIA EMISSION
REGULATIONS FOR ULGE ENGINES.
ENGINE FAMILY : XKZXS.0424WX;EM
ENGINE DISPLACEMENT : 41.5cc
REFER TO OWNER'S MANUMAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
RedMax
Made in Japan
INFORMATION IMPORTANTE
CONCERNANT LE MOTEUR
Ce moteur conformc aux normcs U.S. EPA PH1 et
1995-1999 de la régulementation concernant la
pollution de l'air pour les petits moteurs tout-terrain.
Type de moteur : XKZXS.0424WX;EM
Cylindrée du moteur : 41,5 cc
Se référer au Manuel de l'utilisateur pour
les spécifications d'entretien et les réglages.
RedMax
Made in Japan
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
© Printed in Japan

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement