COMMAND LINK
MULTIFUNCTION METER
(SQUARE)
OPERATION MANUAL
6Y8-2819U-00
To the owner
Thank you for choosing the Yamaha Command Link Multifunction Meter.
This Operation Manual contains information
you will need for proper operation.
A thorough understanding of these simple
instructions and of those in the Owner’s
Manual of the outboard motor will help you
obtain maximum enjoyment of your new
Yamaha. This manual should be considered
a permanent part of this meter and should
remain with it even if the meter is subsequently sold.
In this Operation Manual particularly important information is distinguished in the following ways.
The Safety Alert Symbol means
ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
WARNING
Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, a bystander, or a
person inspecting or repairing the outboard motor.
CAUTION:
A CAUTION indicates special precautions that must be taken to avoid damage
to the outboard motor.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
COMMAND LINK
MULTIFUNCTION METER
(SQUARE)
OPERATION MANUAL
©2005 by Yamaha Motor Co., Ltd.
1st Edition, March 2005
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in Japan
The Command Link Multifunction Meter
enables the display of information through
digital communication with the engine.
The operations of the SET button and the
MODE button are described in this manual
as follows.
Optional parts such as the speed sensor,
cooling water pressure sensor, TriducerMulti sensor, and GPS are described in this
manual by assuming that the parts are
installed and set up on the outboard motor.
Button operations:
The Command Link Multifunction Meter
described in this manual consists of the following.
• Tachometer unit
(Part No.: 6Y8-8350T-0*)
• Speedometer unit
(Part No.: 6Y8-8350S-0*)
• Fuel management meter unit
(Part No.: 6Y8-8350F-0*)
• Speed & Fuel meter unit
(Part No.: 6Y8-83500-0*)
The Command Link Multifunction Meter is
compatible with the following outboard
motors.
4-stroke models:
Fuel injection models only
2-stroke models:
HPDI models only
•
Press the SET button one time.
•
Press the MODE button one time.
•
or
Press the SET button or the MODE button
one time.
•
(1 second)
Press the SET button for 1 second.
•
(4 seconds)
Press the MODE button for 4 seconds.
•
(10 seconds)
Press the MODE button for 10 seconds.
•
(2 times)
Press the MODE button two times.
•
+
Press the SET button and the MODE button simultaneously.
•
+
(10 seconds)
Press the SET button and the MODE button simultaneously for 10 seconds.
Table of contents
1. Tachometer unit ....................... 1
Description .................................. 2
Activating the meter .................... 2
Periodic maintenance
notification ............................. 3
Tachometer ................................. 3
Trim meter................................... 3
Multifunction display .................... 4
Oil pressure display
(4-stroke models) .................. 5
Oil level display
(2-stroke models) .................. 6
Total hour, Trip hour display .... 6
Cooling water/engine
temperature display............... 7
Battery voltage display ............. 8
Cooling water pressure display
(optional: cooling water
pressure sensor has been
installed)................................ 9
Water detection warning .......... 9
Changing backlight settings ...... 10
Adjusting trolling speed ............. 10
Changing settings
(custom mode) ....................... 11
Switching to custom mode ..... 11
Resetting custom mode ......... 12
MAINTENANCE
(resetting maintenance
intervals).............................. 12
TRIM SET (setting trim
angle) .................................. 13
DISPLAY (setting displays) .... 13
FORM (setting display
format)................................. 15
ENGINE NUMBER
(setting corresponding
engine) ................................ 19
Service functions ....................... 20
Diagnosis ............................... 20
Resetting engine number ....... 21
2. Speedometer unit...................
Description ................................
Activating the meter ..................
Speedometer ............................
Fuel meter.................................
Multifunction display..................
Trip display (optional: speed
sensor has been
installed) .............................
Ambient water temperature
display (optional:
Triducer-multi sensor has
been installed) ....................
Depth display (optional:
Triducer-multi sensor has
been installed) ....................
System voltage display ..........
Clock (optional: GPS has
been installed) ....................
Changing backlight settings ......
Changing settings
(custom mode) .......................
Switching to custom mode .....
Resetting custom mode .........
DISPLAY (setting displays)....
UNIT (setting displayed
units) ...................................
FUEL SENSOR
(setting fuel sensor) ............
3. Fuel management meter
unit ...........................................
Description ................................
Activating the meter ..................
Fuel flow meter .........................
Multifunction display..................
Total fuel consumption
display.................................
Fuel economy display ............
Remaining fuel display...........
Changing backlight settings ......
22
23
23
24
25
25
26
27
27
28
28
29
29
29
30
30
32
33
34
35
35
36
37
38
39
40
40
44
45
47
48
48
49
50
50
51
52
52
5. Setting up the meters ............
Activating for the first time.........
Setting the initial settings ..........
Tachometer unit .....................
Speedometer unit ..................
Fuel management meter
unit ......................................
Speed & Fuel meter unit ........
63
63
64
64
64
64
64
Speedometer unit
43
Fuel management
meter unit
UNIT (setting displayed
units) ................................... 59
FUEL SENSOR
(setting fuel sensor) ............ 61
CALIBRATION
(setting correction value) .... 61
53
53
54
54
55
55
56
56
56
57
Speed & Fuel meter
unit
4. Speed & Fuel meter unit ........
Description ................................
Activating the meter ..................
Speedometer.............................
Fuel meter .................................
Multifunction display ..................
Trip display (optional: speed
sensor has been
installed)..............................
Fuel economy display ............
Fuel flow display.....................
Total fuel consumption
display .................................
Ambient water temperature
display (optional:
Triducer-multi sensor has
been installed).....................
Depth display (optional:
Triducer-multi sensor has
been installed).....................
System voltage display ..........
Clock (optional: GPS has
been installed).....................
Changing backlight settings ......
Changing settings
(custom mode) .......................
Switching to custom mode .....
Resetting custom mode .........
DISPLAY (setting displays) ....
41
41
41
42
Setting up the
meters
Changing settings
(custom mode) .......................
Switching to custom mode .....
Resetting custom mode .........
DISPLAY (setting displays) ....
UNIT (setting displayed
units) ...................................
TANK CAPACITY
(setting fuel tank capacity) ..
CALIBRATION
(setting correction value).....
Tachometer unit
Table of contents
1. Tachometer unit
NOTE:
Depending on the model of the outboard motor, some functions may not be compatible. For
information on models which contain the compatible functions, consult a Yamaha dealer.
Tachometer
The tachometer
shows the engine
revolutions per
minute. (Page 3)
Trim meter
The trim meter shows
the trim angle of the
outboard motor in 10
levels. (Page 3)
Adjusting trolling speed
or
: To adjust the trolling speed
randomly. (Page 10)
Multifunction display (Page 4)
· Up to four displays can be switched to show the information.
· Shows up to three types of information combined in one display. In addition,
when an engine malfunction occurs, each indicator blinks to warn of the
malfunction.
Oil pressure display (4-stroke models) (Page 5)
Oil level display (2-stroke models) (Page 6)
Total hour, Trip hour display (Page 6)
Cooling water/engine temperature display (Page 7)
Battery voltage display (Page 8)
Cooling water pressure display (optional) (Page 9)
Water detection warning (Page 9)
· The information shown on each display and the display format combination
can be changed (custom mode).
DISPLAY (setting displays) (Page 13)
FORM (setting display format) (Page 15)
· Periodic maintenance intervals are notified.
Periodic maintenance notification (Page 3)
1
Description/Activating the meter
Activating the meter
When the engine start switch is turned to
ON, the meter is activated and “Welcome”
appears on the multifunction meter. Then,
all the displays come on and the display
switches to the normal display after the total
hour display comes on.
2
1
1 SET button
2 MODE button
5
1
4
7
6
8
1
2
3
4
5
6
7
8
9
2
3
9
Tachometer
Trim meter
Multifunction display
Cooling water pressure
Cooling water/engine temperature
Water detection warning indicator
Battery voltage
Oil level (2-stroke models)
Oil pressure (4-stroke models)
2
Tachometer unit
Description
Tachometer/Trim meter
Tachometer
Periodic maintenance notification
When the hours of engine operation exceed
100 hours, “MAINTENANCE” is scrolled on
the display and the elapsed time from the
previous maintenance period (when the
meter was reset) blinks.
or
The tachometer shows the engine revolutions per minute.
: To return to the normal dis-
play.
Trim meter
The trim meter shows the trim angle of the
outboard motor in 10 levels.
Blinks
NOTE:
• The elapsed time blinks every time the
engine is started until it is reset.
• When the hours of engine operation
exceed 100 hours and the periodic maintenance notification is activated, consult
an authorized Yamaha dealer for periodical maintenance.
• To reset the maintenance period, see
“MAINTENANCE (resetting maintenance
intervals)” in “Changing settings (custom
mode).”
When the angle of the outboard motor
exceeds the trim range, the top segment
blinks.
Blinks
3
Multifunction display
When the engine start switch is turned to
OFF, the last display shown is shown first
when the engine start switch is turned to ON
again.
The multifunction display shows up to three
types of information simultaneously using
numeric values or graphics. In addition, up
to four displays can be set up for the display
configuration with a combination of information. The configuration of the default displays is described below.
NOTE:
To change the display configuration, see
“DISPLAY (setting displays)” in “Changing
settings (custom mode).”
: Press to switch between the displays.
Display 1
(4-stroke)
Display 1
(2-stroke)
Oil pressure +
Total hour
Oil level +
Total hour
Display 2
Total hour, Trip hour
Display 3
Cooling water/
engine temperature +
Battery voltage level +
Oil pressure
Cooling water/
engine temperature +
Battery voltage level +
Oil level
Display 4
Battery voltage value,
Battery voltage level
4
Tachometer unit
Multifunction display
Oil pressure display (4-stroke models)
Oil pressure display (4-stroke models)
NOTE:
• The oil pressure display shows “L” for low
and “H” for high.
• The low oil pressure warning does not display the oil level.
• Depending on the model of the outboard
motor, the oil pressure display may not be
available. If not available, select another
display other than the oil pressure display.
• Depending on the operating conditions
such as when the engine is operated at
extremely low speeds, the oil pressure
may be shown as low even when the
engine is operating properly.
The oil pressure indicator (
) comes on
and the engine oil pressure is shown in 5
levels.
When the engine oil pressure drops too low,
the oil pressure indicator (
) blinks and
the “LOW OIL PRESSURE” warning comes
on.
Blinks
CAUTION:
• Do not operate the engine without
engine oil. Severe engine damage can
result.
• Check the oil level by following the
procedure described in the engine
Owner’s Manual.
• If you cannot locate and correct the
cause, consult a Yamaha dealer.
5
Oil level display (2-stroke models)
The oil level indicator (
) comes on and
the engine oil level is shown in 3 levels.
Total hour, Trip hour display
The total hour display shows the total hours
of engine operation and the trip hour display
shows the trip hours (Tr).
When the engine oil level is low, the oil level
indicator (
) blink and the “EMPTY OIL”
warning comes on.
Blink
+
hours (Tr).
(1 second): To reset the trip
NOTE:
The total hours of engine operation cannot
be reset.
Blink
CAUTION:
Do not operate the engine without engine
oil. Severe engine damage can result.
6
Tachometer unit
Oil level display (2-stroke models)/Total hour, Trip hour display
Cooling water/engine temperature display
Cooling water/engine temperature
display
The cooling water/engine temperature indi-
NOTE:
When one or two displays are shown, the
cooling water/engine temperature display
shows “C” for cool and “H” for hot.
cator (
) comes on and the engine cooling water temperature or the engine
temperature is shown in 5 levels.
When the engine overheats, the cooling
water/engine temperature indicator (
and the “OVERHEAT” warning blink.
)
Blink
CAUTION:
• When the overheat warning comes on,
turn the engine off and check the cooling water inlet for clogs.
• If you cannot locate and correct the
cause, consult a Yamaha dealer.
7
Battery voltage display
When the battery voltage decreases below
the voltage that is required by the engine,
the “LOW VOLTAGE” warning comes on.
The battery voltage indicator (
) comes
on and the battery voltage of the engine is
shown in 5 levels or the voltage value is
shown.
Blink
CAUTION:
• When the low battery voltage warning
comes on, check the battery and the
wiring.
• If you cannot locate and correct the
cause, consult a Yamaha dealer.
When the battery voltage decreases to 12
volts or less or increases to 16 volts or more
the battery voltage indicator (
voltage value blink.
) and the
NOTE:
The voltage level display shows “L” for low
and “H” for high.
Blink
8
Tachometer unit
Battery voltage display
Cooling water pressure display/Water detection warning
Cooling water pressure display
(optional: cooling water pressure sensor
has been installed)
Water detection warning
When water has accumulated in the water
separator (fuel filter), the water detection
The cooling water pressure indicator (
)
comes on and the cooling water pressure is
shown in 5 levels. You can select whether to
display the scale.
warning indicator (
) and the “WATER IN
FUEL” warning blink. This function is not
available for outboard motors that are not
equipped with the water detection warning
function.
Blink
CAUTION:
When the water detection warning comes
on, turn the engine off and remove the
water from the water separator (fuel filter) by following the procedure described
in the Owner’s Manual of the outboard
motor. A malfunction can result if fuel
mixed with water is sent to the engine.
10 PSi
CAUTION:
NOTE:
• When the cooling water pressure
decreases to 10 psi or less, turn the
engine off and check the cooling water
inlet for clogs.
• If you cannot locate and correct the
cause, consult a Yamaha dealer.
or
: To deactivate the buzzer
and return to the display before the warning
was activated.
NOTE:
The cooling water pressure level display
shows “L” for low and “H” for high.
9
Changing backlight settings
Adjusting trolling speed
You can turn the backlight on or off, or
change the brightness level of the backlight
for all meters synchronized. You can also
change the settings for each meter individually.
You can adjust the trolling speed randomly
by increasing or decreasing it approximately
50 r/min.
When in the trolling speed setting mode, the
display switches to the normal display when
the engine speed is increased (within 3,000
r/min) using the throttle. When the throttle is
closed, the display returns to the trolling
speed setting mode.
This function is not available for outboard
motors that are not equipped with the trolling
speed adjustment function.
1.
+
mode.
: To activate the backlight
2.
: Press to switch between the five
brightness levels (1–5).
: To switch between “LIGHT ON”
and “LIGHT OFF.”
1.
3.
+
display.
(1 second): To activate the trolling
speed setting mode.
: To return to the normal
NOTE:
• The backlight default settings are “LIGHT
OFF,” brightness level 1, and “SYNC.”
• If no operations are carried out for 5 seconds or more, the display returns to the
normal display.
• The backlight settings can be changed
from all meters and all displays.
• When “SYNC” is displayed, all meters
operate simultaneously and can be
changed
synchronized.
Press
the
2.
: To decrease the engine speed.
3.
: To increase the engine speed.
4.
button for 1 second to set “SYNC”
so that it is not displayed and to change
the meters individually.
10
(1 second): To return to the normal display and to the default engine
idle speed.
Tachometer unit
Changing backlight settings/Adjusting trolling speed
Changing settings (custom mode)
Changing settings (custom mode)
NOTE:
Switching to custom mode
In the custom mode, you can change the
meter function settings. “CUSTOM” and
each setting function name are scrolled on
the meter.
1. Turn the engine off and the engine start
switch to ON.
• Trolling is affected by currents and other
operating conditions and may differ from
the actual engine speed.
• The default engine idle speed is reset
automatically when the display is switched
to the normal display. The default engine
idle speed is also reset automatically
when the engine is turned off or when the
engine speed exceeds 3,000 r/min.
• When warming up a cold engine, the trolling speed cannot be decreased below the
specified engine idle speed.
• Depending on the model of the outboard
motor, some functions may not be compatible. For information on models which
contain the compatible functions, consult
a Yamaha dealer.
2.
(4 seconds): To activate the custom mode.
3.
: Press to switch between the setting function names (custom mode
selection display).
MAINTENANCE
(resetting maintenance intervals)
TRIM 0SET (setting trim angle)
DISPLAY (setting displays)
FORM (setting display format)
ENGINE NUMBER
(setting corresponding engine)
4.
11
: To switch to the change settings
display.
5.
Change the various settings and return
to the custom mode selection display.
To change the settings, see the corresponding sections for each setting function.
6.
(1 second): To return to the normal display.
MAINTENANCE (resetting maintenance
intervals)
You can reset the elapsed time from the
previous maintenance interval (when the
meter was reset).
1. Turn the engine off and the engine start
switch to ON.
2.
NOTE:
• If no operations are carried out for 30 seconds or more or if the engine is started,
the settings will not be applied and the
display returns to the normal display.
(4 seconds): To activate the custom mode.
3.
: To switch to the resetting display.
• Press the
button for 2 seconds from
step 5 to change the settings and return to
the normal display.
Resetting custom mode
In the custom mode, you can reset the
default settings collectively for all settings
that have been changed.
1. Turn the engine off and the engine start
switch to ON.
2.
Blinks
(4 seconds): To activate the custom mode.
4.
+
(1 second): To reset the
elapsed time to “0h.”
5.
(1 second): To return to the normal display.
NOTE:
Press the
button for 1 second from
step 3 to cancel the resetting of the elapsed
time and return to the custom mode selection display.
3.
+
(10 seconds): To reset all
settings to the default settings.
12
Tachometer unit
MAINTENANCE (resetting maintenance intervals)
TRIM 0SET (setting trim angle)/DISPLAY (setting displays)
TRIM 0SET (setting trim angle)
You can set the trim angle to zero. Fully trim
the outboard motor down.
1. Turn the engine off and the engine start
switch to ON.
00
—
02
5.
—
—
—
—
—
—
03
—
04
—
—
—
—
05
+
(1 second): To adjust the
trim angle to zero using the current trim
position as the standard value.
—
—
01
Total hour,
Trip hour
: To switch to the zero adjustment
display.
Oil pressure/
Oil level
4.
in the table below.
Battery voltage
: To switch between the setting
function names.
Cooling water
pressure
3.
Cooling water/
engine temperature
(4 seconds): To activate the custom mode.
Display
configuration No.
2.
DISPLAY (setting displays)
You can change the display configuration of
the normal display. There are a total of 16
combinations of which up to four displays
can be set up.
The display configuration numbers that have
been selected as the default display configuration are indicated by the shaded areas
—
—
—
—
06
—
07
—
—
08
—
—
09
—
—
10
—
—
NOTE:
11
—
—
—
Press the
button for 1 second from
step 4 to cancel the adjustment of the trim
angle to zero and return to the custom mode
selection display.
12
—
—
—
—
—
—
—
—
6.
(1 second): To return to the normal display.
13
—
14
—
—
—
—
—
—
—
—
15
—
—
—
16
—
—
—
—
—
—
: Displayed
Changing the display configurations:
1. Turn the engine off and the engine start
switch to ON.
13
2.
(4 seconds): To activate the custom mode.
3.
(2 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the display numbers. Select the display number (01–04) you want to change. The
first two digits in the tachometer display
show the display numbers.
* In the display example, display number 01
and display configuration number 13 are
shown.
* When the display configuration number
“00” is selected, “HIDDEN” is shown and
the display is not shown.
7.
(1 second): To change the display
configuration and return to the custom
mode selection display.
8.
(1 second): To return to the normal display.
NOTE:
6.
: To select the display configuration numbers (00–16) you want to
change. The last two digits in the
tachometer display show the display
configuration numbers. Press to switch
between the display configuration numbers.
When changing two or more display configurations of the multifunction display, repeat
steps 5 and 6.
Resetting the display configuration default
settings:
1. Turn the engine off and the engine start
switch to ON.
14
2.
(4 seconds): To activate the custom mode.
3.
(2 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
Tachometer unit
DISPLAY (setting displays)
FORM (setting display format)
5.
+
(1 second): To reset the
display configuration default settings
and return to the custom mode selection display.
6.
(1 second): To return to the normal display.
FORM (setting display format)
You can change the display formats of the
total hour and trip hour (Tr) display, the battery voltage display and the cooling water
pressure display. (The displays can be
changed when there are displays that correspond respectively to displays 1–4.)
Total hour, Trip hour (Tr):
1. Turn the engine off and the engine start
switch to ON.
15
2.
(4 seconds): To activate the custom mode.
3.
(3 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: To select the display number.
The first two digits in the tachometer
display show the display numbers and
the last two digits show the configuration numbers.
6.
: To select the display format.
Press to switch between each display
format.
One display: Display configuration number
(16)
8.
Total hour + Trip hour (Tr)
(1 second): To return to the normal display.
Battery voltage:
1. Turn the engine off and the engine start
switch to ON.
Total hour
Trip hour (Tr)
Blink
2.
(4 seconds): To activate the custom mode.
3.
(3 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: To select the display number.
The first two digits in the tachometer
display show the display numbers and
the last two digits show the display configuration numbers.
6.
: To select the display format.
Press to switch between each display
format.
* In the display example, the total operation
hours and trip hours (Tr) are shown.
Two displays: Display configuration numbers (05, 10, 11)
Total hour
Trip hour (Tr)
Blinks
One display: Display configuration number
(14)
Battery voltage value + Battery voltage level
* In the display example, the trip hours (Tr)
and the cooling water/engine temperature
are shown.
7.
Battery voltage level
(1 second): To change the display
format and return to the custom mode
selection display.
Battery voltage value
16
Tachometer unit
FORM (setting display format)
FORM (setting display format)
Cooling water pressure:
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
(3 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: To select the display numbers.
The first two digits in the tachometer
display show the display numbers and
the last two digits show the display configuration numbers.
6.
: To select the display format.
Press to switch between each display
format.
Blink
* In the display example, the battery voltage
value and battery voltage level are shown.
Two displays: Display configuration numbers (03, 09, 10)
Battery voltage value
Battery voltage level
Blink
* In the display example, the battery voltage
level and the cooling water/engine temperature are shown.
7.
8.
One display: Display configuration number
(13)
(1 second): To change the display
format and return to the custom mode
selection display.
Cooling water pressure level
without scale
(1 second): To return to the normal display.
Cooling water pressure level
with scale
17
Tachometer unit
FORM (setting display format)
Blink
Blink
* In the display example, the cooling water
pressure level (with scale) is shown.
* In the display example, the cooling water
pressure level (with scale) and the oil level
display are shown.
Two displays: Display configuration number
(06)
Two displays: Display configuration number
(08)
Cooling water pressure level
without scale
+ Battery voltage level
Cooling water pressure level
without scale + Total hour
Cooling water pressure level
without scale
+ Battery voltage value
Cooling water pressure level
without scale + Trip hour (Tr)
7.
(1 second): To change the display
format and return to the custom mode
selection display.
8.
(1 second): To return to the normal display.
Cooling water pressure level
with scale
+ Battery voltage level
Two displays: Display configuration number
(07)
Cooling water pressure level
without scale
+ Oil pressure/Oil level
NOTE:
When the corresponding displays are not
available for displays 1–4, FORM is not displayed in the custom mode selection display.
Cooling water pressure level
with scale
+ Oil pressure/Oil level
18
ENGINE NUMBER (setting corresponding engine)
ENGINE NUMBER (setting
corresponding engine)
You can select the engines that are compatible to this meter. The port outboard motor is
set to “No.1 (engine number 1)” and the
starboard outboard motor is set to “No.2
(engine number 2).”
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
(4 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: To switch between the displayed
engine numbers.
7.
NOTE:
• The meters are set at the factory to “No.1
(engine number 1).”
• To engine number, see “Resetting engine
number” in “Service functions.”
No.1 (engine number 1)
No.2 (engine number 2)
No.3 (engine number 3)
No.4 (engine number 4)
6.
(1 second): To return to the normal display.
(1 second): To change the corresponding engine and return to the custom mode selection display.
19
Service functions
CAUTION:
Diagnosis
You can display the self-diagnosis results of
the engine.
(10 seconds): To scroll “DIAGNOSIS”
and to display the diagnosis codes.
When a diagnosis code other than “01”
is displayed, the engine cannot be operated normally. Consult a Yamaha dealer.
NOTE:
When there are no malfunctions, the “01”
diagnosis code is displayed for 3 seconds
and the display returns to the normal display.
Although the custom mode is activated after
a few seconds while the
button is
being pressed, continue to press the button
for 10 consecutive seconds to activate the
diagnosis mode.
When a malfunction occurs, the corresponding diagnosis codes, except “01,” are displayed. When there are multiple diagnosis
codes, “ ” is displayed next to the code
number.
: To display the next code number.
: To return to the normal display.
20
Tachometer unit
Service functions
Service functions
Resetting engine number
When replacing the engines of multiple outboard motors or resetting the setting order,
reset all engine numbers to “No. 1 (engine
number 1).”
1. Turn the engine off and the engine start
switch to ON.
2.
(10 seconds): “ENGINE No.
RESET” will be displayed for 1 second.
3.
Turn the engine start switch to OFF.
The engine number is reset after
approximately 10 seconds.
Turn the engine start switches to ON in
order from port to starboard.
4.
NOTE:
• The engine numbers are stored in the
ECM (Engine Control Module) of each
engine for engine identification.
• The engine numbers are stored in the
ECM (Engine Control Module) when, the
engine start switch is first turned to ON
after being connected. The numbers are
stored in the order from number one to
number four starting from the port outboard motor. When multiple outboard
motors are installed, be sure to wait at
least 2 seconds before turning each
engine start switch to ON.
21
2. Speedometer unit
NOTE:
Speedometer
Shows the speed of
the boat. You can
switch the displayed
unit to miles per hour
(mph), knots, or
kilometers per hour
(km/h). (Page 24)
Fuel meter
The fuel meter shows
the remaining fuel
level in 10 levels.
(Page 25)
Multifunction display (Page 25)
· Up to four displays can be switched to show the information.
· Shows up to two types of information combined on one display.
Trip display (optional) (Page 26)
Ambient water temperature display (optional) (Page 27)
Depth display (optional) (Page 27)
System voltage display (Page 28)
Clock (optional) (Page 28)
· The information shown on each display and the display format combination
can be changed (custom mode).
DISPLAY (setting displays) (Page 30)
22
Speedometer unit
Depending on the model of the outboard motor, some functions may not be compatible. For
information on models which contain the compatible functions, consult a Yamaha dealer.
Description/Activating the meter
Description
Activating the meter
When the engine start switch is turned to
ON, the meter is activated and “Welcome”
appears on the multifunction meter. Then,
all the displays come on and the display
switches to the normal display after a few
seconds.
1
2
1 SET button
2 MODE button
1
3
2
1 Speedometer
2 Fuel meter
3 Multifunction display
23
Speedometer
The speedometer shows the ground speed
or the water speed of the boat. To display
the ground speed, the GPS must be connected to the meter. To display the water
speed, an optional sensor (speed sensor or
Triducer-Multi sensor) must be connected to
the meter.
NOTE:
• If no operations are carried out for 30 seconds or more, the speed sensor is set and
the display returns to the normal display.
• When signals from the GPS cannot be
received even when the GPS function is
on, the GPS display goes off and the
water speed is displayed.
• You can select to show miles per hour
(mph), kilometers per hour (km/h), or
knots on the speedometer display. To
change the displayed unit, see “UNIT (setting displayed units)” in “Changing settings (custom mode).”
Switching the speed sensors:
1.
(4 seconds): To activate the
speed sensor setting mode.
2.
: Press to switch between the
speed sensor types.
“GPS ON” (ground speed)
“GPS OFF” (water speed)
3.
(1 second): To set the speed sensor and return to the normal display.
24
Speedometer unit
Speedometer
Fuel meter/Multifunction display
Fuel meter
Multifunction display
The fuel meter shows the remaining fuel
level in 10 levels and all the segments are
displayed when the fuel tank is full. When
the fuel level is low, the last segment blinks.
When two fuel tanks are connected, the
segments are divided into a left and right
column to show the fuel levels individually.
When only one tank is connected, all segments are displayed to show the fuel level.
The multifunction display shows up to two
types of information simultaneously using
numeric values. In addition, up to four displays can be set up for the display configuration with a combination of information. The
configuration of the default displays is
described below.
: Press to switch between the displays.
Display 1
Trip
Display 2
NOTE:
(not displayed)
The fuel sensor setting can be changed
according to the fuel sensor type. To change
the fuel sensor setting, see “FUEL SENSOR
(setting the fuel sensor)” in “Changing settings (custom mode).”
Display 3
(not displayed)
Display 4
(not displayed)
When the engine start switch is turned to
OFF, the last display shown is shown first
when the engine start switch is turned to ON
again.
25
Trip display
• Since “Display 1” is the only default display, no displays can be switched.
• To change the display configuration, see
“DISPLAY (setting displays)” in “Changing
settings (custom mode).”
+
(1 second): To reset the distance traveled.
NOTE:
• The distance traveled is affected by currents and other operating conditions and
may differ from the actual distance traveled.
• You can select to show miles (M), nautical
miles (NM), or kilometers (km) on the
TRIP display. To change the displayed
unit, see “UNIT (setting displayed units)”
in “Changing settings (custom mode).”
26
Speedometer unit
Trip display (optional: speed sensor has
been installed)
TRIP shows the information from the speed
sensor converted to the distance traveled.
NOTE:
Ambient water temperature display/Depth display
Ambient water temperature display
(optional: Triducer-multi sensor has
been installed)
TEMP shows the ambient water temperature.
Depth display (optional: Triducer-multi
sensor has been installed)
DEPTH or DPTH shows the water depth.
NOTE:
You can select to show feet (F) or meters
(m) on the DEPTH or DPTH display. To
change the displayed unit, see “UNIT (setting displayed units)” in “Changing settings
(custom mode).”
NOTE:
You can select to show Fahrenheit (°F) or
Celsius (°C) on the TEMP display. To
change the displayed unit, see “UNIT (setting displayed units)” in “Changing settings
(custom mode).”
27
System voltage display/Clock
System voltage display
BATTERY or BAT shows the supplied voltage to the meter circuit. The system voltage
display differs from the tachometer unit voltage display (battery voltage). In addition, the
voltage value may be changed according to
the meter connection specifications.
Clock (optional: GPS has been installed)
The clock shows the time in 12 hours. The
local time is easily displayed by calculating
the longitude information received from the
GPS communication data. Set the time as
necessary.
1.
: To activate the time setting mode
and switch to the time setting display.
Blinks
When the battery voltage decreases to 12
volts or less or increases to 16 volts or more
the voltage value blinks.
2.
3.
Blinks
: To change the minutes. Press
and hold to advance quickly.
: To set the hours.
4.
: To change the hours. Press and
hold to advance quickly.
5.
: To set the time and return to the
normal display.
Resetting the time:
CAUTION:
• When the low battery voltage warning
comes on, check the battery and the
wiring.
• If you cannot locate and correct the
cause, consult a Yamaha dealer.
28
1.
: To activate the time setting mode
and to switch to the time setting display.
2.
+
(1 second): To reset the
time to “0:00” and return to the normal
display.
Speedometer unit
Setting the time:
Changing backlight settings/Changing settings (custom mode)
Changing backlight settings
Changing settings (custom mode)
You can turn the backlight on or off, or
change the brightness level of the backlight
for all meters collectively. You can also
change the settings for each meter individually.
Switching to custom mode
In the custom mode, you can change the
meter function settings. “CUSTOM” and
each setting function name are scrolled on
the meter.
1. Turn the engine off and the engine start
switch to ON.
NOTE:
The backlight setting procedure is the same
as that of the tachometer unit. To change
the backlight settings, see “Changing backlight settings” in “1. Tachometer unit.”
2.
(4 seconds): To activate the custom mode.
3.
: Press to switch between the setting function names (custom mode
selection display).
DISPLAY (setting displays)
UNIT (setting displayed units)
FUEL SENSOR
(setting fuel sensor)
4.
5.
6.
29
: To switch to the change settings
display.
Change the various settings and return
to the custom mode selection display.
To change the settings, see the corresponding sections for each setting function.
(1 second): To return to the normal display.
DISPLAY (setting displays)
3.
Clock
0
—
—
—
—
—
(4 seconds): To activate the custom mode.
1
—
—
—
—
2
—
3
—
—
4
—
—
—
—
5
—
6
—
7
—
8
—
—
9
—
—
10
—
—
—
—
—
—
—
—
—
—
—
11
+
(10 seconds): To reset all
settings to the default settings.
—
—
—
—
—
—
—
—
—
12
—
13
—
—
14
—
—
—
15
—
—
—
—
—
—
: Displayed
Changing the display configurations:
1. Turn the engine off and the engine start
switch to ON.
2.
30
(4 seconds): To activate the custom mode.
Speedometer unit
System voltage
2.
Trip
Resetting custom mode
In the custom mode, you can reset the
default settings collectively for all settings
that have been changed.
1. Turn the engine off and the engine start
switch to ON.
Depth
• Press the
button for 2 seconds from
step 5 to change the settings and return to
the normal display.
Ambient water
temperature
• If no operations are carried out for 30 seconds or more or if the engine is started,
the settings will not be applied and the
display returns to the normal display.
Display
configuration No.
DISPLAY (setting displays)
You can change the display configuration of
the normal display. There are a total of 15
combinations of which up to four displays
can be set up.
The display configuration number that has
been selected as the default display configuration is indicated by the shaded
area
in the table below.
NOTE:
DISPLAY (setting displays)
3.
: To switch to the change settings
display.
4.
: Press to switch between the display numbers. Select the display number (1–4) you want to change. The first
two digits in the speedometer display
show the display numbers.
* When the display configuration number 0
is selected, “HIDDEN” is shown and the
display is not shown.
5.
: To select the display configuration number (0–15) you want to change.
The fuel level segments show the display configuration numbers. Press to
switch between the display configuration numbers.
6.
(1 second): To change the display
configuration and return to the custom
mode selection display.
7.
(1 second): To return to the normal display.
NOTE:
When changing two or more display configurations of the multifunction display, repeat
steps 4 and 5.
Resetting the display configuration default
settings:
1. Turn the engine off and the engine start
switch to ON.
* In the display example, display number 2
and display configuration number 12 are
shown.
31
2.
(4 seconds): To activate the custom mode.
3.
: To switch to the change settings
display.
4.
+
(1 second): To reset the
display configuration default settings
and return to the custom mode selection display.
5.
(1 second): To return to the normal display.
UNIT (setting displayed units)
You can change the units that are shown in
each display.
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
: To switch between the setting
function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the displays.
Speedometer (
TEMP
You can select to show Fahrenheit (°F) or
Celsius (°C).
The default setting is Fahrenheit (°F).
DPTH
You can select to show feet (F) or meters
(m).
The default setting is feet (F).
TRIP
You can select to show miles (M), nautical
miles (NM), or kilometers (km).
The default setting is miles (M).
)
TEMP (ambient water temperature)
7.
(1 second): To change the displayed unit and return to the custom
mode selection display.
8.
(1 second): To return to the normal display.
NOTE:
When the speedometer unit settings are
changed, the TEMP, DPTH, and the TRIP
unit settings are collectively changed automatically. To change the settings for each
displayed unit individually, repeat steps 5
and 6.
DPTH (depth)
TRIP (trip)
Blink
* In the display example, the speedometer
is shown.
6.
: Press to switch between the displayed units.
Speedometer
You can select to show miles per hour
(mph), kilometers per hour (km/h), or knots.
The default setting is miles per hour (mph).
32
Speedometer unit
UNIT (setting displayed units)
FUEL SENSOR (setting fuel sensor)
FUEL SENSOR (setting fuel sensor)
You can set the fuel sensor type that is connected to this meter.
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
(2 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the fuel
sensor types.
ABYC (US)
EUROPE
YAMAHA
Blinks
6.
(1 second): To change the fuel
sensor type and return to the custom
mode selection display.
7.
(1 second): To return to the normal display.
33
3. Fuel management meter unit
NOTE:
Depending on the model of the outboard motor, some functions may not be compatible. For
information on models which contain the compatible functions, consult a Yamaha dealer.
Multifunction display (Page 37)
· Up to three displays can be switched to show the information.
· Shows up to two types of information combined on one display.
Total fuel consumption display (Page 38)
Fuel economy display (Page 39)
Remaining fuel display (Page 40)
· The information shown on each display and the display format combination
can be changed (custom mode).
DISPLAY (setting displays) (Page 42)
34
Fuel management
meter unit
Fuel flow meter
The fuel flow meter
shows the fuel
consumption of each
engine per hour or
the total fuel
consumption of all
engines. (Page 36)
Description/Activating the meter
Description
Activating the meter
When the engine start switch is turned to
ON, the meter is activated and “Welcome”
appears on the multifunction meter. Then,
all the displays come on and the display
switches to the normal display after a few
seconds.
2
1
1 SET button
2 MODE button
1
2
1 Fuel flow meter
2 Multifunction display
35
Fuel flow meter
Fuel flow meter
When two outboard motors are installed:
The fuel flow meter shows the fuel economy
of each engine or the total fuel consumption
per hour of all engines.
When multiple outboard motors are
PS (port & starboard)
P (port)
installed, press the
button to switch
between the engines you want to display or
between the total fuel consumption of all
engines.
P
* In the display example, the total fuel consumption of two outboard motors is
shown.
S
PS
When three outboard motors are installed:
PCS (port & center &
starboard)
P (port)
C (center)
S (starboard)
* In the display example, the total fuel consumption of three outboard motors is
shown.
36
Fuel management
meter unit
S (starboard)
Multifunction display
Multifunction display
The multifunction display shows up to two
types of information simultaneously using
numeric values. In addition, up to three displays can be set up for the display configuration with a combination of information. The
configuration of the default displays is
described below.
P
C
: Press to switch between the displays.
S
Display 1
PCS
NOTE:
You can select to show gallons per hour
(gph) or liters per hour (l/h) on the fuel flow
display. To change the displayed unit, see
“UNIT (setting displayed units)” in “Changing the settings (custom mode).”
Total fuel consumption +
Fuel economy
Display 2
(not displayed)
Display 3
(not displayed)
When the engine start switch is turned to
OFF, the last display shown is shown first
when the engine start switch is turned to ON
again.
37
Total fuel consumption display
• Since “Display 1” is the only default display, no displays can be switched.
• To change the display configuration, see
“DISPLAY (setting displays)” in “Changing
settings (custom mode).”
The TTL display cannot measure over 1,999
gallons or 1,999 liters. When exceeding
1,999 gallons or 1,999 liters of fuel, “ ”
blinks in front of the numeric value to indicate an overflow.
Blinks
+
display.
(1 second): To reset the TTL
When the display configuration number is
changed so that the AVAL (available:
remaining fuel) is displayed (see page 40) in
“Changing settings (custom mode),” the TTL
display resetting method is changed.
38
Fuel management
meter unit
Total fuel consumption display
TTL shows the total fuel consumption of all
engines.
NOTE:
Fuel economy display
Resetting the TTL (total fuel consumption)
and AVAL (available: remaining fuel) displays:
Be sure to reset the TTL display on a full
tank of fuel. If the TTL display is reset when
the fuel tank is not full or if not reset and the
fuel tank is filled with fuel, the AVAL display
will not be displayed accurately. When the
TTL display is reset, the AVAL display is
reset simultaneously.
1.
Fuel economy display
ECON shows the distance traveled per unit
of fuel.
+
(1 second): To display the
“TTL AVAL RESET?” confirmation display in the multifunction meter display.
NOTE:
• Fuel economy is affected by the type of
boat being operated and the operating
conditions, and it is constantly changing.
• You can select to show miles per gallon
(MPG), nautical miles per liter (NM/l), or
kilometers per liter (km/l) on the ECON
display. To change the displayed unit, see
“UNIT (setting displayed units)” in “Changing settings (custom mode).”
2.
(1 second) or
+
(1 second): To simultaneously reset the
TTL and AVAL and return to the normal
display.
NOTE:
• Press the
button for 1 second from
step 1 to cancel resetting the TTL display
and return to the normal display.
• You can select to show gallons (G) or
liters (L) on the TTL display. To change
the displayed unit, see “UNIT (setting displayed units)” in “Changing settings (custom mode).”
39
Remaining fuel display/Changing backlight settings
Remaining fuel display
AVAL shows the numeric value of the consumed fuel that is deducted from 90 percent
of the specified fuel tank capacity.
The default setting of the fuel tank capacity
is 50 G (190 L). Change as necessary.
2.
(1 second) or
+
(1 second): To simultaneously reset the
AVAL and TTL displays and return to
the normal display.
NOTE:
• When the AVAL display is reset, the TTL
display is reset simultaneously.
• Press the
button for 1 second from
step 1 to cancel resetting the AVAL display and return to the normal display.
• The displayed units are gallons (G) or
liters (L).
Resetting the AVAL (available: remaining
fuel) and TTL (total fuel consumption) displays:
Be sure to reset the AVAL display on a full
tank of fuel. If the AVAL display is reset
when the fuel tank is not full or if not reset
and the fuel tank is filled with fuel, the display will not be displayed accurately.
1.
You can turn the backlight on or off, or
change the brightness level of the backlight
for all meters collectively. You can also
change the settings for each meter individually.
NOTE:
The backlight setting procedure is the same
as that of the tachometer unit. To change
the backlight settings, see “Changing backlight settings” in “1. Tachometer unit.”
+
(1 second): To display the
“TTL AVAL RESET?” confirmation display in the multifunction meter display.
40
Fuel management
meter unit
Changing backlight settings
Changing settings (custom mode)
Changing settings (custom mode)
Switching to custom mode
In the custom mode, you can change the
meter function settings. “CUSTOM” and
each setting function name are scrolled on
the meter.
1. Turn the engine off and the engine start
switch to ON.
2.
6.
(1 second): To return to the normal displays.
NOTE:
• If no operations are carried out for 30 seconds or more or if the engine is started,
the settings will not be applied and the
display returns to the normal display.
• Press the
button for 2 seconds from
step 5 to change the settings and return to
the normal display.
(4 seconds): To activate the custom mode.
Resetting custom mode
In the custom mode, you can reset the
default settings collectively for all settings
that have been changed.
1. Turn the engine off and the engine start
switch to ON.
3.
2.
(4 seconds): To activate the custom mode.
3.
+
(10 seconds): To reset all
settings to the default settings.
: Press to switch between the setting function names (custom mode
selection display).
DISPLAY (setting display)
UNIT (setting displayed units)
TANK CAPA.
(setting fuel tank capacity)
CALIBRATION
(setting correction value)
4.
5.
: To switch to the change settings
display.
Change the various settings and return
to the custom mode selection display.
To change the settings, see the corresponding sections for each setting function.
41
DISPLAY (setting displays)
DISPLAY (setting displays)
You can change the display configuration of
the normal display. There are a total of 6
combinations of which up to three displays
can be set up.
The display configuration number that has
been selected as the default display configuration is indicated by the shaded
area
in the table below.
Fuel economy
—
—
—
—
1
—
2
3
: To select the display configuration number (0–6). The last two digits in
the fuel flow display show the display
configuration numbers. Press to switch
between the display configuration numbers.
Fuel management
meter unit
Total fuel
consumption
0
Remaining fuel
Display
configuration No.
5.
—
—
4
5
—
6
—
—
—
—
: Displayed
* In the display example, the display number 02 and the display configuration number 6 are shown.
Changing the display configurations:
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
: To switch to the change settings
display.
4.
: Press to switch between the display numbers. Select the display number (01–03) you want to change. The
first two digits in the fuel flow display
show the display numbers.
42
UNIT (setting displayed units)
* When the display configuration number
“0” is selected, “HIDDEN” is shown and
the display is not shown.
6.
7.
UNIT (setting displayed units)
You can change the units that are shown in
each display.
1. Turn the engine off and the engine start
switch to ON.
(1 second): To change the display
configuration and return to the custom
mode selection display.
(1 second): To return to the normal display.
2.
(4 seconds): To activate the custom mode.
3.
: To switch between the setting
function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the displays.
NOTE:
When changing two or more display configurations of the multifunction display, repeat
steps 4 and 5.
Resetting the display configuration default
settings:
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
: To switch to the change settings
display.
4.
+
(1 second): To reset the
display configurations to the default settings and return to the custom mode
selection display.
5.
(1 second): To return to the normal display.
Fuel flow
TTL (total fuel consumption)
ECON (fuel economy)
Blink
* In the display example, the fuel flow is
shown.
6.
: Press to switch between the displayed units.
Fuel flow
You can select to show gallons per hour
(gph) or liters per hour (l/h).
The default setting is gallons per hour (gph).
43
TANK CAPA. (setting fuel tank capacity)
TTL
You can select to show gallons (G) or liters
(L).
The default setting is gallons (G).
ECON
You can select to show miles per gallon
(MPG), nautical miles per liter (NM/l), or kilometers per liter (km/l).
The default setting is miles per gallon
(MPG).
TANK CAPA. (setting fuel tank capacity)
You can set the capacity of the fuel tank that
is connected to this meter.
1. Turn the engine off and the engine start
switch to ON.
7.
(1 second): To change the displayed units and return to the custom
mode selection display.
8.
(1 second): To return to the normal display.
2.
(4 seconds): To activate the custom mode.
3.
(2 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
When the fuel flow unit settings are
changed, the TTL, ECON, and AVAL unit
settings are collectively changed automatically. To change the settings for each displayed unit individually, repeat steps 5 and
6.
Blinks
5.
: Press to switch between the
selected digits.
: Press to switch between the
selected digit numeric values.
44
6.
(1 second): To change the capacity of the fuel tank and return to the custom mode selection display.
7.
(1 second): To return to the normal display.
Fuel management
meter unit
NOTE:
CALIBRATION (setting correction value)
CALIBRATION (setting correction value)
You can calibrate the displayed fuel flow
value within –7 to +7 percent. The difference
in the fuel consumption display and the
actual fuel consumption is calibrated.
NOTE:
• The default setting of the fuel tank capacity is 50 G (190 L). The maximum fuel tank
capacity can be set to 1,999 gallons or
1,999 liters.
• Depending on the position of the fuel outlet and the position of the boat while cruising, the usable fuel may decrease. Be
sure to check the available fuel capacity
before setting the default setting.
• To change the displayed unit, see “UNIT
(setting displayed units)” in “Changing settings (custom mode).”
Checking the calibration value:
1. Operate the outboard motor on a full
tank of fuel.
2. After operating the outboard motor, fill
the fuel tank. Compare the amount of
fuel filled into the fuel tank with the fuel
consumed shown on the fuel consumption display and set the calibration value
to the difference if necessary.
• Press the
and
buttons for 1
second from step 4 to change the default
setting to “0.”
• AVAL shows 90 percent of the specified
fuel tank capacity.
Changing the calibration value:
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
(3 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the calibration values.
Blinks
6.
45
(1 second): To change the calibration value and return to the custom
mode selection display.
CALIBRATION (setting correction value)
7.
(1 second): To return to the normal display.
NOTE:
Fuel management
meter unit
• The fuel flow display may differ depending
on the operating conditions.
• When the fuel flow calibration value is
changed, the fuel flow meter, TTL, ECON,
and AVAL displays are shown calibrated.
46
4. Speed & Fuel meter unit
NOTE:
Depending on the model of the outboard motor, some functions may not be compatible. For
information on models which contain the compatible functions, consult a Yamaha dealer.
Speedometer
Shows the speed of
the boat. You can
switch the displayed
unit to miles per hour
(mph), knots, or
kilometers per hour
(km/h). (Page 49)
Fuel meter
The fuel meter shows
the remaining fuel in
10 levels. (Page 50)
Multifunction display (Page 50)
· Up to five displays can be switched to show the information.
· Shows up to two types of information combined on one display.
Trip display (optional) (Page 51)
Fuel economy display (Page 52)
Fuel flow display (Page 52)
Total fuel consumption display (Page 53)
Ambient water temperature display (optional) (Page 53)
Depth display (optional) (Page 54)
Clock (optional) (Page 55)
· The information shown on each display and the display format combination
can be changed (custom mode).
DISPLAY (setting displays) (Page 57)
47
Description/Activating the meter
Description
Activating the meter
When the engine start switch is turned to
ON, the meter is activated and “Welcome”
appears on the multifunction meter. Then,
all the displays come on and the display
switches to the normal display after a few
seconds.
1
2
1 SET button
2 MODE button
1
3
2
Speed & Fuel meter
unit
1 Speedometer
2 Fuel meter
3 Multifunction display
48
Speedometer
Speedometer
The speedometer shows the ground speed
or the water speed of the boat. To display
the ground speed, the GPS must be connected to the meter. To display the water
speed, an optional sensor (speed sensor or
Triducer-Multi sensor) must be connected to
the meter.
NOTE:
• If no operations are carried out for 30 seconds or more, the speed sensor is set and
the display returns to the normal display.
• When signals from the GPS cannot be
received even when the GPS function is
on, the GPS display goes off and the
water speed is displayed.
• You can select to show miles per hour
(mph), kilometers per hour (km/h), or
knots on the speedometer display. To
change the displayed unit, see “UNIT (setting displayed units)” in “Changing settings (custom mode).”
Switching the speed sensors:
1.
(4 seconds): To activate the
speed sensor setting mode.
2.
: Press to switch between the fuel
sensor types.
“GPS ON” (ground speed)
“GPS OFF” (water speed)
3.
(1 second): To set the speed sensor and return to the normal display.
49
Fuel meter/Multifunction display
Fuel meter
Multifunction display
The fuel meter shows the remaining fuel
level in 10 levels and all segments are displayed when the fuel tank is full. When the
fuel level is low, the last segment blinks.
When two fuel tanks are connected, the
segments are divided into a left and a right
column to show the fuel levels individually.
When only one tank is connected, all segments are displayed to show the fuel level.
The multifunction display shows up to two
types of information simultaneously using
numeric values. In addition, up to five displays can be set up for the display configuration with a combination of information. The
configuration of the default displays is
described below.
: Press to switch between the displays.
Display 1
Trip
+ Fuel economy
Display 2
Fuel flow
+ Total fuel
consumption
NOTE:
The fuel sensor setting can be changed
according to the fuel sensor type. To change
the fuel sensor setting, see “FUEL SENSOR
(setting the fuel sensor)” in “Changing settings (custom mode).”
(not displayed)
Display 4
(not displayed)
Display 5
(not displayed)
50
Speed & Fuel meter
unit
Display 3
Trip display
When the engine start switch is turned to
OFF, the last display shown is shown first
when the engine start switch is turned to ON
again.
Trip display (optional: speed sensor has
been installed)
TRIP shows the information from the speed
sensor converted to the distance traveled.
NOTE:
• Since “Display 1” and “Display 2” are the
only default displays, other displays cannot be switched.
• To change the display configuration, see
“Display (setting displays)” in “Changing
settings (custom mode).”
+
(1 second): To reset the distance traveled.
NOTE:
• The distance traveled is affected by currents and other operating conditions and
may differ from the actual distance traveled.
• You can select to show miles (M), nautical
miles (NM), or kilometers (km) on the
TRIP display. To change the displayed
unit, see “UNIT (setting displayed units)”
in “Changing settings (custom mode).”
51
Fuel economy display/Fuel flow display
Fuel flow display
FLOW shows the total fuel consumption per
hour of all engines.
NOTE:
NOTE:
• Fuel economy is affected by the type of
boat being operated and the operating
conditions, and it is constantly changing.
• You can select to show miles per gallon
(MPG), nautical miles per liter (NM/l), or
kilometers per liter (km/l) on the ECON
display. To change the displayed unit, see
“UNIT (setting displayed units)” in “Changing settings (custom mode).”
You can select to show gallons per hour
(GPH) or liters per hour (l/h) on the FLOW
display. To change the displayed unit, see
“UNIT (setting displayed units)” in “Changing settings (custom mode).”
Speed & Fuel meter
unit
Fuel economy display
ECON shows the distance traveled per unit
of fuel.
52
Total fuel consumption display/Ambient water temperature display
Ambient water temperature display
(optional: Triducer-multi sensor has
been installed)
TEMP shows the ambient water temperature.
Total fuel consumption display
TTL shows the total fuel consumption of all
engines.
The TTL display cannot measure over 1,999
gallons or 1,999 liters. When exceeding
1,999 gallons or 1,999 liters of fuel, “ ”
blinks in front of the numeric value to indicate an overflow.
NOTE:
You can select to show Fahrenheit (°F) or
Celsius (°C) on the TEMP display. To
change the displayed unit, see “UNIT (setting displayed units)” in “Changing settings
(custom mode).”
Blinks
+
display.
(1 second): To reset the TTL
NOTE:
You can select to show gallons (G) or liters
(L) on the TTL display. To change the displayed unit, see “UNIT (setting displayed
units)” in “Changing settings (custom
mode).”
53
Depth display/System voltage display
Depth display (optional: Triducer-multi
sensor has been installed)
DEPTH or DPTH displays the water depth.
System voltage display
BATTERY or BAT shows the supplied voltage to the meter circuit. The system voltage
display differs from the tachometer unit voltage display (battery voltage). In addition, the
voltage value may be changed according to
the meter connection specifications.
NOTE:
When the battery voltage decreases to 12
volts or less or increases to 16 volts or more
the voltage value blinks.
Blinks
CAUTION:
• When the low battery voltage warning
comes on, check the battery and the
wiring.
• If you cannot locate and correct the
cause, consult a Yamaha dealer.
54
Speed & Fuel meter
unit
You can select to show feet (F) or meters
(m) on the DEPTH or DPTH display. To
change the displayed unit, see “UNIT (setting displayed units)” in “Changing settings
(custom mode).”
Clock/Changing backlight settings
Clock (optional: GPS has been installed)
The clock shows the time in 12 hours. The
local time is easily displayed by calculating
the longitude information received from the
GPS communication data. Set the time as
necessary.
Changing backlight settings
Setting the time:
NOTE:
1.
You can turn the backlight on or off, or
change the brightness level of the backlight
for all meters collectively. You can also
change the settings for each meter individually.
The backlight setting procedure is the same
as that of the tachometer unit. To change
the backlight settings, see “Changing backlight settings” in “1. Tachometer unit.”
: To activate the time setting mode
and switch to the time setting display.
Blinks
2.
3.
: To change the minutes. Press
and hold to advance quickly.
: To set the hours.
4.
: To change the hours. Press and
hold to advance quickly.
5.
: To set the time and return to the
normal display.
Resetting the time:
1.
: To activate the time setting mode
and switch to the time setting display.
2.
+
(1 second): To reset the
time to “0:00” and return to the normal
display.
55
Changing settings (custom mode)
Changing settings (custom mode)
Switching to custom mode
In the custom mode, you can change the
meter function settings. “CUSTOM” and
each setting function name are scrolled on
the meter.
1. Turn the engine off and the engine start
switch to ON.
2.
6.
(1 second): To return to the normal display.
NOTE:
• If no operations are carried out for 30 seconds or more or if the engine is started,
the settings will not be applied and the
display returns to the normal display.
• Press the
button for 2 seconds from
step 5 to change the settings and return to
the normal display.
(4 seconds): To activate the custom mode.
Resetting custom mode
In the custom mode, you can reset the
default settings collectively for all settings
that have been changed.
1. Turn the engine off and the engine start
switch to ON.
3.
2.
(4 seconds): To activate the custom mode.
3.
+
(10 seconds): To reset all
settings to the default settings.
: Press to switch between the setting function names (custom mode
selection display).
UNIT (setting displayed units)
FUEL SENSOR
(setting fuel sensor)
CALIBRATION
(setting correction value)
4.
5.
: To switch to the change settings
display.
Change the various settings and return
to the custom mode selection display.
To change the settings, see the corresponding sections for each setting function.
56
Speed & Fuel meter
unit
DISPLAY (setting displays)
Trip
Fuel flow
Fuel economy
Total fuel
consumption
Ambient water
temperature
Depth
System voltage
Clock
DISPLAY (setting displays)
You can change the display configuration of
the normal display. There are a total of 36
combinations of which up to five displays
can be set up.
The display configuration numbers that have
been selected as the default display configuration are indicated by the shaded areas
in the table below.
Display
configuration No.
DISPLAY (setting displays)
0
—
—
—
—
—
—
—
—
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2
—
3
—
—
4
—
—
—
5
—
—
—
—
6
—
—
—
—
—
7
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
8
—
9
—
—
10
—
—
—
11
—
—
—
—
12
—
—
—
—
—
13
—
—
—
—
—
—
14
—
—
—
—
—
—
15
—
—
—
—
—
—
16
—
—
—
—
—
—
17
—
—
—
—
—
18
—
—
—
—
—
—
19
—
—
—
—
—
—
20
—
—
—
—
—
—
21
—
—
—
—
—
22
—
—
—
—
—
23
—
—
—
—
24
—
—
—
—
—
25
—
—
—
—
—
26
—
—
—
—
—
27
—
—
—
—
—
28
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
29
—
—
—
—
—
—
—
—
—
—
—
—
30
—
31
—
—
32
—
—
—
33
—
—
—
—
34
—
—
—
—
—
35
—
—
—
—
—
—
36
—
—
—
—
—
—
: Displayed
57
—
—
—
DISPLAY (setting displays)
* In the display example, the display number 3 and the display configuration number 36 are shown.
Changing the display configurations:
1. Turn the engine off and the engine start
switch to ON.
2.
(4 seconds): To activate the custom mode.
3.
: To switch to the change settings
display.
4.
: Press to switch between the display numbers. Select the display numbers (1–5) you want to change. The first
two digits in the speedometer display
show the display numbers.
* When the display configuration number 0
is selected, “HIDDEN” is shown and the
display is not shown.
6.
(1 second): To change the display
configuration and return to the custom
mode selection display.
7.
(1 second): To return to the normal mode.
5.
When changing two or more display configurations of the multifunction display, repeat
steps 4 and 5.
: To select the display configuration numbers (0–36) you want to
change. The fuel level display segments
(the left column represents the tens digit
and the right column represents the
ones digit) show the display configuration numbers. Press to switch between
the display configuration numbers.
Resetting the display configuration default
settings:
1. Turn the engine off and the engine start
switch to ON.
36
58
2.
(4 seconds): To activate the custom mode.
3.
: To switch to the change settings
display.
4.
+
(1 second): To reset the
display configurations to the default settings and return to the custom mode
selection display.
Speed & Fuel meter
unit
NOTE:
UNIT (setting displayed units)
5.
UNIT (setting displayed units)
You can change the units that are shown in
each display.
1. Turn the engine off and the engine start
switch to ON.
(1 second): To return to the normal display.
2.
(4 seconds): To activate the custom mode.
3.
: To switch between the setting
function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the displays.
Speedometer (
)
TRIP (trip)
FLOW (fuel flow)
ECON (fuel economy)
TTL (total fuel consumption)
TEMP (ambient water temperature)
DPTH (depth)
Blink
* In the display example, the speedometer
is shown.
59
UNIT (setting displayed units)
: Press to switch between the displayed units.
Speedometer
You can select to show miles per hour
(mph), kilometers per hour (km/h), or knots.
The default setting is miles per hour (mph).
TRIP
You can select to show miles (M), nautical
miles (NM), or kilometers (km).
The default setting is miles (M).
FLOW
You can select to show gallons per hour
(GPH) or liters per hour (l/h).
The default setting is gallons per hour
(GPH).
ECON
You can select to show miles per gallon
(MPG), nautical miles per liter (NM/l), or kilometers per liter (km/l).
The default setting is miles per gallon
(MPG).
TTL
You can select to show gallons (G) or liters
(L).
The default setting is gallons (G).
TEMP
You can select to show Fahrenheit (°F) or
Celsius (°C).
The default setting is Fahrenheit (°F).
DPTH
You can select to show feet (F) or meters
(m).
The default setting is feet (F).
7.
(1 second): To change the displayed units and return to the custom
mode.
8.
(1 second): To return to the normal display.
NOTE:
60
When the speedometer unit settings are
changed, the TRIP, FLOW, ECON, TTL,
TEMP, and DPTH settings can be collectively changed automatically. To change the
settings for each displayed unit individually,
repeat steps 5 and 6.
Speed & Fuel meter
unit
6.
FUEL SENSOR (setting fuel sensor)/CALIBRATION (setting correction value)
FUEL SENSOR (setting fuel sensor)
You can set the fuel sensor type that is connected to this meter.
1. Turn the engine off and the engine start
switch to ON.
CALIBRATION (setting correction value)
You can calibrate the displayed fuel flow
value within –7 to +7 percent. The difference
in the fuel consumption display and the
actual fuel consumption is calibrated.
2.
(4 seconds): To activate the custom mode.
3.
(2 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the fuel
sensor types.
Checking the calibration value:
1. Operate the outboard motor on a full
tank of fuel.
2. After operating the outboard motor, fill
the fuel tank. Compare the amount of
fuel filled into the fuel tank with the fuel
consumed shown on the fuel consumption display and set the calibration value
to the difference if necessary.
Changing the calibration value:
1. Turn the engine off and the engine
switch to ON.
ABYC (US)
EUROPE
YAMAHA
2.
(4 seconds): To activate the custom mode.
3.
(3 times): Press to switch
between the setting function names.
4.
: To switch to the change settings
display.
5.
: Press to switch between the calibration values.
Blinks
6.
(1 second): To change the fuel
sensor type and return to the custom
mode selection display.
7.
(1 second): To return to the normal display.
Blinks
6.
61
(1 second): To change the calibration value and return to the custom
mode selection display.
CALIBRATION (setting correction value)
7.
(1 second): To return to the normal display.
NOTE:
Speed & Fuel meter
unit
• The fuel flow display may differ depending
on the operating conditions.
• When the fuel flow calibration value is
changed, the FLOW, TTL, and ECON displays are shown calibrated.
62
Activating for the first time
5. Setting up the meters
Activating for the first time
To install the meters and the optional sensors and to connect the meters to the
engine, see the “Command Link Multifunction Meter Installation Manual.”
Be sure to follow the procedures in “Activating for the first time” and “Setting the initial
settings.” If the procedures are performed
incorrectly, the engine number will change,
resulting in improper operation.
1. Installing the meters
2. Connecting the meters to the engine
3. Installing an optional sensor
4. Activating for the first time
5. Setting the initial settings
After installing the meters, be sure to turn
the engine start switch to ON when the
power is supplied for the first time. When
multiple outboard motors are installed, be
sure to turn the engine start switch to ON
from the port outboard motor and to wait at
least 2 seconds before turning each engine
start switch to ON.
NOTE:
• The engine number of the engine whose
engine start switch was first turned to ON
is stored in the ECM (Engine Control Module) of the engine as the port engine
(engine number 1).
• To reset an engine number, see “Resetting engine number” under “Service functions” in “1. Tachometer unit.”
If the procedures are performed incorrectly,
see “Service functions” in “1. Tachometer
unit” to reset all of the engine numbers.
Check the connections, and follow the setup
procedures again to set up the meters.
63
Setting the initial settings
Setting the initial settings
DISPLAY (setting displays)
Change the display configuration number as
necessary so that the AVAL display can be
displayed. (See page 42.)
Before operating the meter, be sure to
change the default settings as described
below. For the setting procedures, see the
corresponding setting procedure for each
meter.
Speed & Fuel meter unit
FUEL SENSOR (setting fuel sensor)
Set the fuel sensor according to the fuel
tank type. (See page 61.)
Tachometer unit
ENGINE NUMBER (setting corresponding
engine)
Select the engine compatible to this meter.
(See page 19.)
TRIM 0SET (setting trim angle)
Adjust the trim angle to zero. (See page 13.)
DISPLAY (setting displays)
When the optional cooling water pressure
sensor is connected, change the display
configuration number so that it can be displayed in the cooling water pressure display.
When the oil pressure display function is not
available on your model, change the display
configuration number so that the oil pressure display is not included. (See page 13.)
DISPLAY (setting displays)
When the optional Triducer-Multi sensor and
GPS are connected, change the display
configuration number to display the ambient
water temperature, depth, and clock displays. (See page 57.)
Speedometer unit
FUEL SENSOR (setting fuel sensor)
Set the fuel sensor according to the fuel
tank type. (See page 33.)
Setting up the
meters
DISPLAY (setting displays)
When the optional Triducer-Multi sensor and
GPS are connected, change the display
configuration number to display the ambient
water temperature, depth, and clock displays. (See page 30.)
Fuel management meter unit
TANK CAPA. (setting fuel tank capacity)
Set the capacity of the connected fuel tank.
(See page 44.)
64
YAMAHA MOTOR CO., LTD.
Printed in Japan
March 2005 – 1.5 × 1 CR
(E)
Printed on recycled paper