Audiovox FPE2005 Operating instructions

Operating Instructions
__________________________________________________
Model No.: FPE2005
20” LCD TV
For assistance, please call: 1-800-619-3848
Or visit us at http://www.audiovox.com
128-7354
Congratulations on your purchase of this LCD TV.
We recommend that you read this manual thoroughly before use to fully enjoy the
many functions and excellent features of this unit.
Keep this manual in an easily accessible location for future reference.
Note:Screen displays and illustrations in this manual may differ from the actual
model.
Contents Index
Overview
Important safety information
Important safety cautions
Accessories
Identification of controls
Control buttons
Back
Remote control
Installation
Basic operations
Main on-screen-display (OSD) introduction
Operations
Picture adjustment
System setting
Audio setting
Channel setting
Selecting channel
OSD setting
Timer setting
Operations in YbPr mode
TV troubleshooting
Notices
Maintenance/repair
Specifications
3
4
5
7
8
8
9
10
12
19
20
2
21
21
22
27
29
31
32
33
34
36
40
41
42
Overview
General Description
This Audiovox product is a Color Active Matrix liquid Crystal Display (LCD) with an integral
Cold Cathode Fluorescent Lamp (CCFL) backlight system. The matrix employs a Thin Film
Transistor (TFT) as the active element. This TFT-LCD has a 20.1 inch diagonally measured
active display area with a native 640x480 pixel resolution. Each pixel is divided into red,
blue, and green sub-pixels which are arranged in vertical stripes. The color palette is
capable of more then 16.7 million colors.
This Audiovox product incorporates a tilt stand that can be removed for easy wall mounting.
The wall mounting compatibility of this product is completed by incorporating a VESA 100
wall mount standard bolt configuration. A separate VESA 100 compatible wall mount kit will
be required to properly secure the unit to the wall.
This units has a great viewing angle allowing the unit to be seen at almost any viewing angle
with minimal loss in picture quality. The high brightness and contrast ratio will make this TV
a pleasure to watch.
3
Important Safety Information
The lightning flash with the arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “DANGEROUS
VOLTAGE” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The Exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (Servicing instructions in
the literature accompanying the product).
Federal Communication Commission
This Equipment has been tested and found to comply with the limits for a TV Broadcast Receiver, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectio n against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications If this equipment does cause or receive interference, which can be determined by
turning equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
 Reorient or relocate the TV antenna
 Increase the separation between TV and other equipment.
 Connect TV into separate outlet from equipment.
Consult the dealer or an experienced radio/TV technician for help
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment
4
Important Safety Cautions
When any unusual situation occurs, turn off the power supply at once and remove
the plug from the wall outlet. Contact a qualified service department in your local
area.
Do not expose this unit in the rain or spatter by liquid. Do not use this product near
water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, and the like. Do not use immediately after
moving from a low temperature to high temperature environment, as this causes
condensation, which may result in fire, electric shock, or other hazards.
Heat sources-Keep the product away from heat sources such as radiators, heaters, stoves
and other heat generating products (including amplifiers).
Requirement of environment temperature:
0oC~50oC for storage; 5oC~40oC for working
The vents and other openings in the cabinet are designed for ventilation. Do not
cover or block these vents and openings since insufficient ventilation can cause
overheating and/or shorten the life of the product.
Do not place the product on a bed, sofa, rug or other similar surface, since they can
block ventilation openings.
This product is not designed for built-in installation; do not place the product in an
enclosed place such as a bookcase or rack, unless proper ventilation is provided
or the manufacturer's instructions are followed.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
Do not place the product on an unstable trolley, stand, tripod or table. Placing the
product on an unstable base can cause the product to fall, resulting in
serious personal injuries as well as damage to the product. Use only a trolley,
stand, tripod, and bracket or table recommended by the manufacturer or sold with
the product.
5
Important Safety Cautions
When relocating the product placed on a trolley, it must be moved with the utmost
care. Sudden stops, excessive force and uneven floor surfaces can cause the
product to fall from the trolley.
The power cords must be routed properly to prevent people from stepping on them
or objects from resting on them. Check the cords at the plugs and product. Powersupply cords should be routed so that they are not likely to be walked on or
snagged by items placed upon or against them. Pay particular attention to cords at
doors, plugs, receptacles, and the point where they exit from the product.
If the power cord or the plug is damaged contact a qualified service department for
service.
Do not overload wall outlets, extension cords, or convenience receptacles on other
equipment as this can result in a risk of fire or electric shock.
High Voltage exists in this TV set. Do not remove the cover.
In case the product needs replacement parts, make sure that the service person
uses replacement parts specified by the manufacturer, or those with the same
characteristics and performance as the original parts. Use of unauthorized parts
can result in fire, electric shock and/or other danger.
The LCD panel used in this product is made of glass. Therefore, it can break when
the product is dropped or impacted upon by other objects. Be careful not to be
injured by broken glass pieces in case the LCD panel breaks.
Don't try to push anything into the cabinet or place any vessel with water on the TV
set.
For added protection for this television equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna. This will prevent damage to the equipment
due to lightning and power-line surges.
6
Important Safety Cautions
Important Information Regarding use of
Video Games, Computer, captions or other
fixed images displays
The extended use of a fixed image program material can cause permanent “Shadow Image” on
the LCD panel. The background image is viewable on normal programs in the form of stationary
fixed images. This type of irreversible LCD panel deterioration can be limited by observing the
following steps:
* Reduce the Brightness and Contrast settings to a minimum viewing level
* DO NOT display the fixed image for extended periods of time
* Turn the power OFF when not in actual use
Recycling
This product utilizes tin-lead solder, and has a fluorescent lamp containing a small amount of
mercury. Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance Environment at: http://www.eiae.org/
Accessories
1..
2..
3..
4..
5..
6..
FPE2000 TV unit
Power adaptor (AC/DC)
AC Power cord
Remote Control (Model Specific)
Batteries
Audio/Video cable (RCA)
7
Identification of controls
Control buttons
Control Panel
SOURCE
MENU
Menu
CH
CH
VOL
VOL
Power On/
Standby
Channel Down/Up
Volume Down/Up
Select Input Signal
Speaker
Speaker
Remote Sensor
Power Indicator
1. SOURCE
The Power Indicator light will glow
To access the SOURCE select menu
yellow when the set is turned on,
2. MENU
and glows red when the set is in
Press this button to access the MENU main page.
the standby mode.
3. CH +/Change the TV channel.
In OSD Menu, press these buttons to choose the OSD items.
4. VOL +/Increase or decrease the sound volume level.
In OSD Menu, press these buttons to adjust the value or setting of each item
5. POWER ( )
Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to
STANDBY.
Note:
SOURCE, MENU, CH+/-, VOL+/- and POWER(
) on the main unit have the same functions as the
corresponding buttons on the remote control.
This operation manual provides a description based on operating functions with the remote control.
8
Identification of controls (continued)
Back
2
1
DC 12V
PC - AUDIO
Y
Pb
Pr
4
3
R AUDIO L
PHONE
VIDEO
HDT V IN
L AUDIO R
AV OUT
6
5
VIDEO
L AUDIO R
S-VIDEO
AV IN
1. DC POWER input
Connect to the DC output of the Power Adapter.
2. HDTV input (Y, Pb, Pr, Audio L, R)
Connect to the Y/Pb/Pr (or Y/Cb/Cr) and audio output jacks of a Set-Top Box or DVD player.
3. Headphone 3.5mm jack
4. AV outputs (Video, Audio L, R)
Connect to the VCR input jacks to record programs.
5. AV inputs (Video, Audio L, R)
Receive video/audio signals from external sources such as VCR or DVD player.
6. S-Video input
Receive a S-Video signal from external source such as VCR or DVD player.
7.Coaxial cable & Antenna input
9
7
RF
Remote Control
Power on/standby
Mute
Volume up/down selector;
In the menu operation,
adjust the selected item
Channel up/down selector.
In menu operations, used
to select item.
Access the menu
Exit the menu
S.M
Select OSD menu position
Sound preset mode selector
Setting sleep timer
Change audio to mono, stereo or SAP
Auto correct picture
Previous channel
Display the current state
Select picture mode between
Bright, Nature, Soft & User
Direct channel selector
Select the input signal source
Adjust the treble
Adjust the bass
Flip the cover open in
the arrow direction.
10
Preparing the Remote Control
Please install the batteries before using the remote control.
Batteries for the Remote Control
If the remote control fails to operate the LCD TV functions, replace the batteries in the remote control.
1 Open the battery cover.
2
<(Slide
the cover while
pressing down.)
Insert two size-AAA batteries.
3
Replace the cover and slide
in reverse until the lock
snaps.
<(Place
the batteries with their
terminals corresponding to the (+)
and (-) indications in the battery
compartment.)
Effective range of the remote control
Notes:
1.When the remote control will not be used for a
long period of time or when the batteries are
worn out, remove the batteries.
2.Do not drop or dampen the remote control.
3.Do not disassemble the remote control.
4.There should be no obstacle between the TV
and the transmitter.
5.Use the remote control within the effective
30
30
5m
range as shown in the figure on the left.
6.If the remote control does not work, please
check whether the batteries are exhausted or
if they have been installed properly.
7.When direct sunlight, and incandescent
lighting, fluorescent lamp or any other strong
light shines on the remote sensor of the TV,
the remote operation can be come erratic.
8.Do not mix different types of batteries in the
remote.
11
Installation
Install the unit in a room where direct light will not fall upon the screen.
Total darkness or a reflection on the picture screen may cause
eyestrain. Soft and indirect lighting is recommended for comfortable
viewing.
Antenna connections
OUTDOOR VHF/UHF ANTENNA CONNECTION (ANTENNA NOT INCLUDED)
Follow the instructions for the type of antenna system you intend to use. If using Cable or satellite, see
the next page.
Combination VHF/UHF
Combination VHF/UHF
Antenna (Single 75 Ohm cable Antenna (Separate VHF and
or 300 Ohm twin-lead wire)
UHF 300 Ohm twin-leads)
UHF 300 Ohm
VHF/UHF
Ohm
75 OHM
Connect the 75 Ohm cable from
combination VHF/UHF antenna
to the antenna jack.
OR
If your combination antenna has
a 300 Ohm twin-lead wire, use a
300-75 Ohm matching
transformer (NOT SUPPLIED).
Combiner
VHF 300
Ohm
Connect the UHF twin-lead wire
to a combiner (NOT SUPPLIED).
Connect the VHF twin-lead to a
300-75 Ohm matching
transformer (NOT SUPPLIED).
Attach the transformer to the
combiner. Attach the combiner to
the antenna jack.
12
UHF 300 Ohm
Combiner
VHF 75 Ohm
Connect the 75 Ohm cable from
the VHF antenna and the UHF
antenna twin-lead wire to a
combiner (NOT SUPPLIED).
Attach the combiner to the
antenna jack.
NOTE: If your VHF antenna has
a twin-lead wire use a 300-75
Ohm matching transformer, then
connect the transformer to the
Installation
Cable (CATV)/satellite connections
This TV has an extended tuning range and can tune most cable channels without using a Cable TV converter box.
Some Cable TV companies offer "premium pay channels" in which the signal is scrambled. Descrambling these
signals for normal viewing requires the use of a descrambler device which is generally provided by the cable
company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a converter/descrambler box,
connect the CATV 75 ohm coaxial cable to the VHF/UHF jack on the
rear of the TV.
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE OR SATELLITE
If you subscribe to a satellite service or a cable TV service which requires the use of a converter/
descrambler box, connect the incoming 75 Ohm coaxial cable to the converter/descrambler box. Using
another 75 Ohm cable, connect the output of the converter/descrambler or satellite box to the antenna jack
on the TV. Follow the connections shown below. Set the TV/VCR to the output channel of the
converter/descrambler or satellite box (usually 3 or 4) and use the converter/descrambler or satellite box to
select channels.
INCOMING
75 Ohm
CATV CABLE
CONVERTER/DESCRAMBLER
OR SATELLITE BOX (NOT SUPPLIED)
75 Ohm CABLE
TO TV/VCR
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE
WITH SCRAMBLED PREMIUM CHANNELS
If you subscribe to a satellite service or a cable TV service in which basic channels are unscrambled and
premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter
and an A/B switch box (available from the cable company or an electronic supply store). Follow the
connections shown below. With the switch in the "B" position, you can directly tune any nonscrambled
channels on your TV. With the switch in the "A" position, tune your TV to the output of the
converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to tune
scrambled channels.
CONVERTER/DESCRAMBLER
(NOT SUPPLIED)
INCOMING
75 Ohm
CATV CABLE
A
B
SPLITTER
(NOT SUPPLIED)
13
A/B SWITCH
(NOT SUPPLIED)
75 Ohm
CABLE
Installation(continued)
Power connection
3
Household
power outlet
2
Power cord
1
Connect to the DC input
socket of the back of the
product.
Be sure to fully insert plug
into the connection and
confirm it is secure.
AC adapter
1. Connecting the female plug to the AC socket on AC adapter.
2. Connecting the AC adapter to the DC power input of the set.
3. Connecting the male plug to the wall outlet as illustrated.
Note:
<Always turn off the Power to the LCD TV when connecting the AC adapter.
<This product should only be operated with the type of power source marked on the lable on the
unit.
<Always unplug the AC adapter from the product and power outlet when the LCD TV is not in use for
an extended period of time of time.
<The illustration of power cord and power outlet is only for your reference and may vary depending
on your area.
14
Installation(continued)
Elevation adjustment
You can adjust the angle of the LCD TV as follows.
o
o
The elevation can be adjusted from -5 to +10 average.
10
-5
15
Installation(continued)
Notes about connection
1. Carefully check the terminals for position and type before making any connections.
2. Loose connectors will result in image or color problems. Make sure that all connectors are securely inserted into their
terminals.
3. When connecting an external device, turn off the power of the main unit first to prevent any possible damage.
Connecting the Video/Audio equipment
You can connect the unit to a DVD or VCR to enjoy playback with high quality picture and sound.
Please refer to the instruction manual of the equipment to be connected.
Composite Video signal connection
Connect the composite video signal terminal on the TV to the output of AV equipment through composite cable.
If you select the video signal, please set the input signal source of LCD TV to AV mode.
DC 12V
Y
Pb
Pr
R AUDIO L
PHONE
VIDEO
DTV IN
L AUDIO R
Y
Yellow (video)
w White (audio, L)
R
Red
L AUDIO R
S-VIDEO
RF
AV IN
Y
w
R
To S-VIDEO input
To video input To audio inputs
(audio, R)
Y
VCR, DVD etc.
VIDEO
AV OUT
To video output
w
R
To audio outputs
(NOT SUPPLIED)
To S-VIDEO output
Note: Composite video is the most common used signal, but the picture quality is not as high as S-video.
S-VIDEO Signal Connection
Connect the S-video terminal on the TV to the output of AV equipment using a S-video cable.
If you select S-video signal, please set the input signal source of LCD TV to SVIDEO mode.
S-Video is a signal format which transfers the color and brightness of the picture with higher quality than a
16
Installation(continued)
AV OUT connection
DC 12V
Y
Pb
Pr
R AUDIO L
PHONE
VIDEO
L AUDIO R
AV OUT
DTV IN
Y
W
S-VIDEO
L AUDIO R
RF
AV IN
R
To video output
Y
VIDEO
To audio outputs
Yellow (video)
w White (audio, L)
R
Red
(audio, R)
To audio inputs
To video input
Y
R
W
To audio inputs
W
R
VCR for recording
ANT OUT
(Not Supplied)
AV OUT
VIDEO
L AUDIO R
S - VIDEO
ANT IN
AV IN
VIDEO
L AUDIO R
Audio amplifier
(Not Supplied)
Rear of the VCR
How to connect:
Connect the video/audio output terminals on the TV set to the signal input terminals of the VCR equipment or the
video/audio input terminals on other TV set through a video/audio cable.
Connect the audio output terminals on the TV set to the Audio amplifier through audio cable.
How to record the TV program:
1. Connect cables as shown above.
2. Turn on the LCD TV and select source.
3. Turn on the VCR and insert the tape.
4. Select the video input from the VCR menu that corresponds to the AV in on the VCR.
5. Press the “RECORD” button to begin recording.
How to enjoy high quality sound by Audio amplifier:
1. Connect cables as shown above.
2. Turn the volume of the Audio amplifier to minimum.
3. Turn on the LCD TV and select source.
4. Connect the RCA (Red/White) cable from the TV AV OUT to the AUX input on the back of the Audio Amplifier.
5. Set the Audio Amplifier to AUX INPUT.
6. Turn on the audio amplifier and adjust for a proper volume.
17
Installation(continued)
YPbPr input connection
Please connect the YPbPr input terminals on the TV set for better picture quality. And connect the audio outputs
with the corresponding audio input terminals on the TV set.
If you select YPbPr signal, please set the input signal source of the LCD TV to YPbPr / YCbCr mode.
DC 12V
Y
Pb
Pr
PHONE
R AUDIO L
VIDEO
G
B
R
L AUDIO R
AV OUT
DT V IN
R
VIDEO
L AUDIO R
S-VIDEO
RF
AV IN
W
Y Yellow (video)
W
white (audio L)
R red (audio R, Pr)
Audio
cable
Video
cable
G Green (Y)
B Blue (Pb)
G
B
R
R
W
Set-Top Box, DVD player, etc.
ANT
HDTV OUT
Y
Pb
Pr
R AUDIO L
AUDIO
AV OUT
R AUDIO L
VIDEO
(Not Supplied)
S - VIDEO
Rear of the STB, DVD
Notes:
The Y, Pb, Pr outputs on your DVD player are sometimes labeled Y, Cb, Cr. If so, connect the cables to like
colors.
18
Basic Operations
Turning on
1
Connect the power correctly, then the red indicator lights up and the
unit is in STANDBY mode. (See Page 14.)
2
Press the POWER ( )button on the remote control or on the unit to
turn on the TV set.The indicator LED will turn to yellow.
Turning off
1
With the power on, press the POWER ( ) button to turn off the TV and
put the TV in STANDBY mode, the indicator LED will turn to red.
2
If you want to turn off the power completely, unplug the power cord
from the wall outlet.
S.M
Note: Do not switch the on/off state of the unit quickly. The interval of
the turning on and turning off should be more than 5 seconds.
Selecting input signal
1
Press the SOURCE button on the unit or
button on the remote control. The screen
displays the menu as shown on the right.
SOURCE
TV
AV
2
Press CH5/6 to highlight your desired
input signal source. Press VOL+/- or wait
for about 4 seconds and the desired signal
source will be selected.
Note:
SVIDEO
YPbPr/YCbCr
TV
All buttons shown in the manual are located on the
remote control unless otherwise indicated.
19
Main On-Screen-Display (OSD)
introduction
TV/AV/S-VIDEO MODE
YPbPr/YCbCr MODE
Picture Setting Menu
brightness
50
contrast
50
color
18
sharpness
32
tint
0
Picture Setting Menu
CC 1
----
V-chip settings
Audio Setting Menu
SRS
on
MTS
mono stereo SAP
bass
0
treble
0
balance
0
50
Picture Position MENU
6
ccd mode settings
50
contrast
customer temp setting
on
backlight
brightness
color temp 5000K 7300K 9300K user
System Setting Menu
blue screen
1 Press MENU button to display menu screen.
2 Press VOL+/- to select the menu.
3 Press CH6 to access the menu.
4 Press CH5/6 to select the item.
5 Press VOL+/- to adjust the item.
6. Press EXIT button twice to exit the menu.
h position
50
v position
50
phase
15
frequency
866
Audio Setting Menu
off
SRS
on
off
bass
0
treble
0
balance
0
Channel Setting Menu
System Setting Menu
9
channel number
antenna/cable
antenna
cable
sleep time
add/erase
add
erase
Back light
20
minutes
6
48
fine tune
channel search
OSD Setting Menu
OSD Setting Menu
language
language
English
OSD background opaque
OSD timeout
English
OSD position
OSD position
OSD background opaque
translucent
30 seconds
OSD timeout
Signal Information Menu
Signal Information Menu
resolution: 640 X 480/60Hz
mode:
40
video type: 650 X 462/60Hz
mode:
3
Note: in AV/S-VIDEO mode, Channel Setting menu
can not be accessed and there is no MTS menu item
in Audio Setting menu.
translucent
30 seconds
Note: in YPbPr/YCbCr mode, there are no color
temp and customer temp setting menu items in
Picture Setting menu.
20
Operations
Picture adjustment
S.M
1
Access Picture Setting menu
by pressing MENU.
2
Press CH5/6to select the item
that you want to adjust.
3
Press VOL+/- to adjust
selected item.
Item
brightness
contrast
color
sharpness
brightness
contrast
color
sharpness
tint
Function
To adjust picture's brightness
To adjust picture's contrast
To adjust picture's color
To adjust picture's sharpness
You can select picture mode by
P.M button. There are four
picture modes: Bright, Nature,
Soft and User.
0
Range
0-100
0-100
0-36
0-63
To adjust picture's tint
tint
50
50
19
32
-32-+31
soft
bright
user
nature
Bright: Select for a bright picture.
Nature: Select for a standard picture.
Soft: Select for a soft picture.
NOTE: Setting the unit to a Bright Picture with high brightness
and contrast levels will cause picture quality loss.
21
Operations (continued)
System setting
blue screen setting

耋晤憮
1 Access the System Setting menu.
blue screen
on
6
backlight
ccd mode settings CC 1
---V-chip settings
2
Press CH5/6to select blue screen
item.
3
Press VOL+/- to select off or on.
If you select on, the screen displays blue background when there is
no signal. If you select off, the screen displays static when there is
no signal.
Note: Only when the blue screen is on, the set will turn off
automatically after 15 minutes if there is no signal.
S.M
backlight adjustment
1
Access the System Setting menu.
2
Press CH5/6to select backlight
item.
3
Press VOL+/- to adjust the backlight
brightness.
blue screen
23
on
6
backlight
ccd mode settings CC 1
---V-chip settings
Operations (continued)
System setting
Setting Closed Caption(CCD)
1 Access the System Setting menu.
blue screen
2
Press CH5/6 to select
ccd
mode settings item.
3
on
backlight
6
ccd mode settings CC 1
V-chip settings
----
Press VOL+/- to select . You can select the caption data channel
(CC1, CC2, CC3, CC4), the text service channel(text1, text2,
text3, text4) or turn off the Closed Caption(Off).
S.M
Note:
1. Some TV programs may not be broadcast with closed caption
signals, and therefore the TV will not be able to display captions,
Also, text information is not offered by all stations.
2. Some TV programs only provide one channel caption, one channel
text, or only caption without text.
Parental Control with V-Chip
1
Access the System Setting menu.
blue screen
2
Press CH5/6to select V-Chip
settings item.
on
backlight
ccd mode settings
6
CC 1
V-chip settings
----
3 Enter the password using the keypad to access the V-chip submenu.(The default password is 1234 and you should change the
password after you access the sub-menu.)
4
Press CH5/6to select Vchip
global setting item. Use VOL+/- to
select disable or enable. If you
select enable, the function is
activated. If you select disable, the
function is not active.
23
Vchip global setting
movie blocking
enable
G
TV blocking
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
****
Operations (continued)
System setting (V-Chip Sub-menu)
Movie Blocking setting
This function allows programs to be restricted and TV usage to be
controlled based on program rating. It prevents children from watching
violent or sexual scenes that may be harmful.
Please enter the V-chip sub-menu (previous page).
1
Press CH5/6button to select movie
blocking item.
2
Press VOL+/- button to select
desired rating.
S.M
Vchip global setting
movie blocking
enable
G
TV blocking
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
****
Movie Ratings:
* NONE
* G and Above (general audience)
* PG and Above (parental guidance suggested)
* PG-13 and Above (13 years and up)
* R and Above (restricted)
* NC-17 and Above (18 years and up)
* X (adult)
If you set PG-13, G and PG movies will be available, and PG-13, R,
NC-17 and X will be blocked.
TV blocking setting
This function allows TV programs to be restricted and TV usage to be
controlled based on age and content. It prevents children from
watching violent or sexual scenes that may be harmful.
Age base
Please enter the V-chip sub-menu (previous page).
1 Press
CH5/6button to select TV
blocking item.
Vchip global setting
movie blocking
enable
G
TV blocking
2 Press
VOL+/- button to select the
desired rating.
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
****
TV Ratings:
* NONE
* Y and Above (all children) (individual content categories do not apply)
* Y7 (7 years and up)
* G and above (general audience) (individual categories do not apply)
* PG and Above (parental guidance suggested)
* 14 and above (14 years and up)
* MA (mature audience)
24
V-Chip enables parents to prevent their children from watching inappropriate material on TV. V-Chip reads the
ratings for programming (except for news, sports, unedited movies on premium cable,and Emergency System
signals ), then denies access to programming if the program's rating meets the limitations you select. In this case,
the program will be blocked.
Content based
Please enter the V-chip sub-menu first (page 24).
1 Press
CH5/6button to select TV
blocking setting... item.
Vchip global setting
enable
G
movie blocking
TV blocking
2 Press
VOL+ button to access the
sub-menu.
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
****
3 Setting the content with CH+/- and
VOL+/- buttons.
FV
S.M
V
S
L
D
TV-Y7 show
Content Categories:
* FV: fantasy violence
* V: violence
* S: sexual situations
* L: adult language
* D: sexual dialogue
TV-PG
show show show show
TV-14
show show show show
TV-MA
show show show
(applies only to TV-Y7)
(applies to TV-PG and above, TV14 and Above, TV-MA)
(applies to TV-PG and above, TV14 and Above, TV-MA)
(applies to TV-PG and above, TV14 and Above, TV-MA)
(applies to TV-PG and Above, TV14)
Canadian English Blocking setting
Please enter the V-chip menu first (page 24).
1
Press CH 5/6 button to select
Canadian English blocking item.
Vchip global setting
movie blocking
enable
G
TV blocking
2
Press VOL+/- button to select the
desired rating.
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
Canadian English Language Ratings:
* E: Exempt.
* C: Children.
* C8+: Children 8 years and older.
* G: General programming, suitable for all audiences.
* PG: Parental guidance.
* 14+: Viewers 14 years and older.
* 18+: Adult programming.
25
****
Operations (continued)
System setting (V-Chip Sub-menu)
Canadian French blocking setting
Please enter the V-chip sub-menu first (page 24).
1 Press
CH 5/6 button to select
Canadian French blocking item.
Vchip global setting
movie blocking
2 Press VOL+/- button to select desired
rating
enable
G
TV blocking
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
****
Canadian French Language Ratings:
* E: Exempt.
* G: Children.
* 8 ans+: Children 8 years and older.
* 13 ans+: Children 13 years and older.
* 16 ans+:Viewers 16 years and older.
* 18 ans+: Adult programming.
S.M
Changing the password
Please enter the V-chip sub-menu first (page 24).
1 Press
CH 5/6 button to select
change password item.
2
Vchip global setting
movie blocking
Input a new 4-digit password by using
the keypad on the remote.
enable
G
TV blocking
Y
Canadian English blocking E
Canadian French blocking E
TV block setting...
change password
****
Next time when you want to access the V-chip menu, you will use your
new password. Make sure to remember the password.
26
Operations (continued)
Audio Setting
Selecting the MTS
1
2
3
Access the Audio Setting menu.
Press CH5/6 to select MTS item.
Press VOL+/- to select mono,
stereo or SAP(secondary audio
program).
SRS
MTS
bass
treble
balance
on
off
mono stereo SAP
0
0
0
You can also directly press STEREO button on the remote control
to select the MTS. The MTS mode changes as follows:
S.M
MONO
STEREO (If the program is STEREO)
MONO
SAP
MONO
STEREO
(If the program is SAP)
SAP (If the program is STEREO & SAP)
NOTE: SAP = Secondary Audio Program.
Adjusting volume
Press VOL+/- to adjust volume.
Press VOL+ button, the volume
increases. Press VOL- button,
the volume decreases.
(Range:0-100)
volume
75
Muting the sound
You can press the button on the
remote control to mute the sound.
Press the
button again to
restore. You can also press VOL+
to restore the sound.
Selecting the sound mode
You can press S.M button on the remote control to switch the sound
mode between user, movie, music, and news.
Movie: Select for a movie program.
Music: Select for a music program.
News: Select for a speech or talk program.
Custom settings mode in the Audio Setting OSD are saved under
USER mode.
27
Operations (continued)
Audio Setting
Adjusting the bass/treble
1
Access the Audio Setting menu.
2
Press CH5/6to select bass or
treble item.
3
Press VOL+/bass or treble.
S.M
to
SRS
MTS
bass
treble
balance
on
off
mono stereo SAP
0
0
0
adjust the
You can press the Bass+/- buttons on the remote control to adjust
the bass directly;and you can also press theTreb+/- buttons on the
remote control to adjust the treble directly.
Adjusting the sound balance
1 Access the Audio Setting menu.
2 Press
CH5/6to select balance
item.
3 Press
VOL+/- to adjust the
balance of the left track and right
track.
SRS
MTS
bass
treble
balance
on
off
mono stereo SAP
0
0
0
SRS
MTS
bass
treble
balance
on
off
mono stereo SAP
0
0
0
Adjusting the SRS
1
Access the Audio Setting menu.
2
Press CH5/6 to select SRS
item.
3
Press VOL+/- to select on or off.
SRS (Sound Retrieval System®) is an audio enhancement technology
that restores the spatial cues that are present in a live listening
environment and processes it to provide a natural 3D sound field.
* The SRS symbol are trademark of SRS Labs,Inc.
SRS technology is incorporated under license from SRS Labs, Inc.
28
Operations (continued)
Channel Setting
Selecting antenna/cable
1 Access Channel Setting menu.
2 Press CH5/6to select
antenna/cable item.
3 Press VOL+/- button to select
channel number
9
antenna/cable antenna cable
add/erase
add
erase
48
fine tune
channel search
antenna or cable.
S.M
Please select antenna or cable before you start Auto
Search. If the TV is connected to antenna, please select
antenna. If the TV is connected to cable, please select
cable.
Auto Search
Please access the Channel Setting menu first.
In Channel Setting menu, press
1 CH
5/6button repeatedly to
highlight channel search item.
channel number
9
antenna/cable antenna
cable
add/erase
erase
add
fine tune
channel search
2 Press
VOL+/Search.
to start Auto
All active channels will be preset
and stored into the memory
automatically.
29
antenna searching
48
Operations (continued)
Channel Setting
Adding/Erasing Channels
After the Channel SEARCH, you can Add/Erase channels
that you watch when you press the CH5/6 to change
channels.
1
2
S.M
Select the channel number which you want
to erase using the keypad.
Access the Channel Setting
menu.
3
Press CH5/6to select
add/erase item.
4
Press VOL+/- to select erase.
When you press CH5/6 to
change channels, this channel
will be skipped.
If you want to resume a skipped
channel, use the keypad
buttons to enter the channel,
then access the Channel
Setting menu, press VOL+/- to
select add. When you press
CH5/6to change channels, the
channel will be present.
channel number
9
antenna/cable antenna
cable
add/erase
erase
add
48
fine tune
channel search
channel number
9
antenna/cable antenna
cable
add/erase
erase
add
48
fine tune
channel search
Fine tuning
Please access the Channel Setting menu first.
In Channel Setting menu,
1 press
CH5/6button repeatedly
to highlight Fine tune item.
2 Press VOL+/-
to fine tune to
achieve best picture and sound.
30
channel number
9
antenna/cable antenna
cable
add/erase
erase
fine tune
channel search
add
48
Operations (continued)
Selecting channel
Using Keypad buttons
1
To select one-digit channel numbers:
Input the channel using the 0-9 number button, then press
Channel Enter
button to confirm.
2
To select two-digit channel numbers:
Input the channel using the 0-9 number button, then press
Channel Enter
button to confirm.
S.M
3
To select three-digit channel numbers:
Input the channel using the 0-9 number button directly.
Note: The period between presses should be within 2 seconds.
Using Channel up/down buttons
1
2
Press CH5button, the channel number increases;
Press CH6 button, the channel number decreases.
NOTE: This feature works after a channel search is complete.
Using previous channel button
Press
button to switch between the current channel and
previous channel.
* You can press DSP button to
Know current channel number
information.
33
Operations (continued)
OSD Setting
Setting the language of the menu
1
Access the OSD Setting menu.
2
Press CH5/6 to select the language
item.
Press VOL+/- to select an OSD
language. English, Spanish and French
can be selected.
3
S.M
language
English
OSD position
OSD background opaque translucent
OSD timeout
30 seconds
language
English
Setting the position of the menu
1
Access the OSD Setting menu.
2
Press CH5/6to select the OSD
position item.
3
OSD position
OSD background opaque translucent
Press VOL+/- to select the position of
the menu displaying.
OSD timeout
30 seconds
You can also press the OSD POSITION button on the
remote control to select OSD menu position.
Setting the background of the menu
1
Access the OSD Setting menu.
2
Press CH5/6to select the OSD
background item.
language
English
OSD position
3
Press VOL+/- to select opaque or
translucent. If you select Opaque,
the
background of the menu is
opaque. If you select translucent, the
background of the menu is
translucent.
OSD background opaque translucent
30 seconds
OSD timeout
Setting the OSD timeout
1
Access the OSD Setting menu.
2
Press CH5/6to select the OSD
timeout item.
3
Press VOL+/- to set the timeout: 5,
10, 15, 20, 25, 30, 35, 40, 45, 50, 55,
60 seconds.
32
language
English
OSD position
OSD background opaque
OSD timeout
translucent
30 seconds
Operations (continued)
Timer setting
Using Sleep button
Press SLP button to display sleep

耋晤憮
timer menu. Press CH5/6 or
VOL+/- repeatedly to set sleep time
between:0, 10, 20, 30, 60, 90, 120,
180, 240 minutes. If you select 0
minute, the sleep timer function is
turned off.
Press the SLP button again to exit the
menu.
S.M
33
sleep timer
30 minute
Operations in /YPbPr mode
Select YPbPr mode
1
2
Press the SOURCE button on the unit
or button
on the remote control.
The screen displays the menu shown
as right.
Press CH5/6 to highlight the
YPbPr/YCbCr item. Press VOL+/- or
wait about 4 seconds and the signal
source is selected.
S.M
34
SOURCE
TV
AV
SVIDEO
YPbPr/YCbCr
Operations in VGA /YPbPr mode(continued)
Picture Settings
Adjusting Brightness/Contrast
1 Access the PICTURE menu.
2 Press CH5/6to select brightness
or contrast item.
3
brightness
50
contrast
50
color temp 5000K 7300K 9300K user
Press VOL+/- to adjust the
customer temp setting
selected item.
Item
S.M
Function
brightness Adjust the brightness of the picture.
Notes
Will Not affect the display settings in the TV, AV mode.
contrast Adjust the contrast of the picture.
Setting the color temperature
1
Access the Picture Setting
menu.
2
Press CH5/6to select color
temp item.
3
Press VOL+/- to switch the color
temperature between 5000K,
7300K, 9300K and User.
4
If you want to change the value of
the user mode, set color temp to
user first, then select customer
temp setting item, and press
VOL+/- to access the sub-menu.
5
Press CH5/6to select the item
and press VOL+/- to adjust it. The
value you set will be stored .
35
brightness
50
contrast
50
color temp 5000K 7300K 9300K User
customer temp setting
user red
50
user green
50
user blue
50
36
TV
37
TV
38
TV
39
40
619-3848
41
Specifications
Specifications:
Model Number: FPE2005
ver: 00
UPC number: 0-44476-02740-6
Display Features
Display type
TFT LCD
Screen Size
20.1" (diagonal)
Active Area
408 (H) x 306 (V) mm
Aspect Ratio
4:3
Panel Resolution
640x480
Brightness
450 Cd/m² (typical)
Contrast ratio
500:1
Viewing Angle
160(H) : 140(V)
0.2125(H) x 0.6375(V) mm
Dot Pitch
Maximum Color
16.7 Million
Response time (Tr&Tf)
16ms (typical)
Backlight life
60,000hrs
TV Reception
TV System
NTSC
Channel CATV - UHF/VHF
181 Channel
Antenna Impedance
75Ohm
Connector type
F
Audio
Maximum Audio Output
5watt x 2
Total number of speakers
2
Video Connections
Quantity
NTSC Analog TV Tuner
1
ATSC Digital TV Tuner
N/A
Composite Video Input
1
S-Video Input (4pin DIN)
1
Component Input (Y,Pb,Pr)
1 (480p, 720p, 1080i**)
Component Input (Y,Cb,Cr)
N/A
VGA Input (15 pin D-Sub)
N/A
DVI Input (DVI-D, DVI-I)
N/A
HDMI Input
N/A
CableCARD
N/A
Composite Video Output
1
S-Video Output
N/A
Component Output (Y,Pb,Pr)
N/A
Component Output (Y,Cb,Cr)
N/A
VGA Output (15 pin D-Sub)
N/A
DVI Output (DVI-D, DVI-I)
N/A
HDMI Output
N/A
Video Standards Supported
Composite Video input
PAL/NTSC
S-Video Input
PAL/NTSC
RF
NTSC
Audio Connections
Quantity
Stereo Mini Phono Jack Input (3.5mm)
N/A
RCA Input(Red, White)
1
Optical Digital Input
N/A
Coax Digital Input
N/A
Headphone:(Variable/Fixed) (3.5mm)
1 (variable)
Stereo Mini Phono Jack Output (3.5mm)
N/A
RCA Output(Red, White)
1
Optical Digital Output
N/A
Coax Digital Output
N/A
N/A = Not Available
Features
VESA wall mount compatible
EDTV Ready
Tilt stand with built-in Handle
User Friendly remote and On Screen Display (OSD)
Ultra slim design
181 Channel Cable/AIR TV tuner built in
High resolution Composite and S-Video input
Accessories in the box
Wall mounting Bracket Kit
AC/DC power supply
Power cord
Owners manual
Warranty Card
Product Registration card
Remote Control (model Specific)
2-AAA batteries
FPE2005 TV unit
Power Requirements
Power Source
AC 100-240V, 50/60Hz
Unit input power
12VDC 5A 60W
Standby consumption
<2W
Dimension (WxHxD)
Unit W/stand
25.1 x 17.4 x 7.5 inches
Unit W/O stand
25.1 x 14.9 x 2.6 inches
Weight (N.W.)
Unit W/stand
20.3 lbs
Unit W/O Stand
17 lbs
Warranty
Parts & Labor
12 Month
Environment
Operating Temperature
41 - 95°F
Operating Humidity
10% - 95%
43
42
FPE2005
9093
43
PRINTED IN
RECYCLED PAPER
128-7354
604-L20H33-02