Samsung SP-H700 Specifications

Owner's Instructions
SP-H700/H710/H500
Table of Contents
Preparation
Table of Contents
Preparation
Picture Adjustment
Features and Design..............................................4
Selecting Picture Mode ......................................30
Caution on Lamp Use and Replacement ..............5
Custom Settings of the Picture ..........................31
Projector and Accessories
Front/Upper Side and Accessories ........................8
Rear Side and Cables ........................................10
Remote Control Buttons ....................................11
Operating the Remote Control............................12
Changing the Color Standard ............................32
Installation and Basic Adjustments
Installation and Turning On ..............................14
Zooming and Focus Adjustment..........................16
Leveling with Adjustable Feet ............................17
Using the Lens Shift Dial....................................18
Screen Size and Projection Distance....................19
Setting up DNle ..................................................36
Selecting and Adjusting Color Temperature ....33
Gamma Correction ..............................................34
Saving Custom Picture Settings ........................35
Selecting Picture Size..........................................37
Screen Position Adjustment ..............................39
Film Mode ............................................................40
Overscan ..............................................................41
Still Picture ..........................................................42
Setup
Flipping/Reversing the Projected Image ........44
Connections and Source Setup
Correcting Vertical Keystone ............................46
Before Connections ............................................22
Test Patterns ......................................................47
Connecting to Video Equipment
Connecting to VCR/Camcorder/Cable Box ..........23
Connecting to DVD ............................................24
Connecting to the Digital TV Receiver..................25
Restoring the Factory Default Settings ............48
Setting up the External Input Source ................26
Naming the External Connections ....................27
2
Light Setting ........................................................45
Information ..........................................................49
Other Information
Setting the Language ..........................................52
Storage and Maintenance ..................................72
Setting the Menu Position..................................53
Purchasing Optional Parts..................................73
Setting the Menu Translucency..........................54
Structure of Screen Menu ..................................74
Setting the Menu Display Time..........................55
Lamp Replacement ..............................................77
Selecting Quick Menu..........................................56
RS-232C Connection and Control ......................78
Preparation
Menu Option
Specifications ......................................................80
Remote Control Specifications ..........................81
Before Connecting to PC ....................................58
Setting up the PC Environment ..........................59
Connecting to PC..................................................60
Automatic Picture Adjustment ..........................62
Table of Contents
Connecting to PC
Frequency Adjustment ........................................63
Fine Tuning with the Phase Adjustment ..........64
Zooming the Screen ............................................65
Reset the PC ........................................................66
Troubleshooting
Before Contacting Service Personnel ................68
3
Features and Design
Preparation
Optical engine adopting advanced DLP technology
■
■
■
■
SP-H700/SP-H710: DLPTM HD2+ DMD panel capable of 1280x720 resolution
SP-H500: DLPTM ED2+ DMD panel capable of 1024x576 resolution
5X-speed color wheel designed to reduce digital artifacts
250W Lamp designed to improve luminance
Vivid colors
Features and Design
■
Quality picture tuning focused on improving color - this unit aims at
realizing color coordinates that meet broadcasting standards on
video production.
Minimized fan noise and light leakage
■
The airflow and fan installation structure are optimized to minimize
fan noise and beam leakage.
Various Input Ports
■
Five types of input ports including a DVI-D (compatible with HDCP)
port, two Component ports improve connection to external
peripherals.
User adjustments
4
■
This unit allows adjustment of each input port.
■
The unit has a reference pattern that can be used for positioning and
adjustment.
■
The remote control is backlit to improve usability in a dark
environment.
Caution on Lamp Use and Replacement
The Projector lamp changes in nature depending on time of use and
using environment. Refer to the installation and other
recommended operational sections of the user’s manual to avoid
rapid degradation of performance and deterioration of picture
quality. The projector lamp requires regular replacement.
■
Free servicing will be offered within 90 days after purchasing of the
product and within 300 hours of product use, if the problem is due
to a defective lamp.
■
You can check the lamp use time by pressing the INFO button on
the remote control.
Caution on Lamp Replacement
■
Unplug the power cord before replacing the lamp.
■
Inside of the projector is very hot. Cool off the projector for at least
an hour after turning off.
■
Contact your dealer to purchase a lamp for replacement.
(Ultra violets from the lamp can damage your eyes.)
■
Turn off the power of the lamp before replacement or repair.
(Due to the high-pressure of the lamp, it is possible to explode.)
■
When the lamp is broken, be careful not to be hurt by glass pieces.
Refer to the manual for proper handling.
Caution on Lamp Use and Replacement
■
Preparation
Projector Lamp
Caution on Lamp Use
■
This projector produces intense light. Do not stare light source
directly.
■
Do not touch the exhaust vent during operation. It can be very hot.
■
Do not expose the unit to rain or moisture.
5
V
I
S
U
A
L
R
E
A
L
I
S
M
Preparation
Projector and Accessories ............................8
Installation and Basic Adjustments ..........14
PROJECTOR AND ACCESSORIES
Front/Upper Side and Accessories
Front/Upper Side
Preparation
11
10
9
8
7
1
Projector and Accessories
2
6
3
4
5
Indicators
- TEMP (Red LED)
- LAMP (Blue LED)
- STAND BY (Blue LED)
Refer to page 9 for details.
7
MENU
Used to open the on-screen Menu.
8
POWER
Used to turn the projector on or off.
2
Remote Control Signal Receiver
9
3
Focus Ring
Used for Focus Adjustment.
SOURCE
Used to select input signals from the external
sources.
4
Lens
5
Adjustable Feet
You can adjust the screen position by moving
up and down the adjustable feet.
1
6
Zoom Knob
Used to enlarge or reduce image size.
10 Select and Move Button
Used to select an menu item, and to move the
cursor.
11 LENS SHIFT Dial
You can adjust screen images up and down
within the lens range.
Accessories
Remote Control/
2 Batteries
8
Power Cable
Owner's Instructions
Indicator Information
: Turned On
LAMP
STANDBY
: Turned Off
Information
Clearing Indicator Problems
Classification
Measure 1
Measure 2
Measure 3
Measure 4
NOTE
State
Measures
Projector and Accessories
If you press the POWER button on the remote control or projector, the screen
appears within 30 seconds.
The projector is in normal operating condition.
The projector is warming up after POWER button has been pressed.
The POWER button is pressed to turn off the projector, and the cooling system is
in operation to cool off inside of the projector. (Lasts for about 1 minute and 30
seconds)
Refer to measure 1 below if the cooling fan inside the projector is not in normal
operation condition.
Refer to measure 2 below if the lamp cover protecting the lamp unit is not closed
properly.
Power is turned off automatically when temperature inside of the projector goes
beyond the control limit. Refer to measure 3.
Refer to measure 4 below if the life span of the lamp is running out or a problem
with the lamp is detected.
Preparation
TEMP
: Flashing
Unplug and plug the cord and restart the projector. If the
When the cooling fan system is
not in normal operating condition. problem does not disappear, contact a dealer or service
personnel near you.
Check the screw on the bottom side of the projector. If you
When the lamp cover protecting
do not find any problem, contact a dealer or service
the lamp unit is not properly
closed or the sensor system is not personnel near you.
in normal operating condition.
Adjust the position of the projector following the
When temperature inside of the
installation instructions of this manual and cool off the
projector becomes too high.
projector before restarting it. If the problem does not
disappear, contact a dealer or service personnel near you.
Power off the projector and cool it off for some time before
The lamp is malfunctioning after
restarting it.
abnormal power off or restarting
right after turning off the projector.
Check how long the lamp has been used on Information
When brightness of the picture
and contact a dealer or service personnel near you for lamp
screen degrades or image
replacement.
deterioration is found.
This Projector uses a cooling fan system to keep the unit from overheating.
Operation of the cooling fan may cause noise, which does not affect the product performance.
No exchange or refund for the noise concern.
9
PROJECTOR AND ACCESSORIES
Rear Side and Cables
Rear Side
Preparation
1
Projector and Accessories
7
2 3
4
8
5
6
9
1
Remote Control Signal Receiver
4
RS-232C port
7
AC Power Input
2
S-VIDEO Input port
5
DVI Input port
8
Power Switch
3
COMPOSITE Input ports
6
PC Input port
9
Component Input port
Cables
10
Power Cord
Connected to the wall
outlet ∏.
Video (COMPOSITE) Cable
Connected to the
connection port ˇ.
PC Video Cable
Connected to the
connection port Ø.
DVI-D Cable
Connected to the
connection port ˆ.
S-Video Cable
Connected to the
connection port ´.
Component Cable
Connected to the
connection port ’.
PROJECTOR AND ACCESSORIES
Remote Control Buttons
12
2
COMP.1 (Pages 24~26)
Used to switch to COMPONENT 1 Mode.
3
COMP.2 (Pages 24~26)
Used to switch to COMPONENT 2 Mode.
4
S-VIDEO (Pages 23, 26)
Used to switch to S-VIDEO Mode.
5
P.SIZE (Page 37)
Used to adjust the size of picture screen.
6
P.MODE (Page 30)
Used to select Picture Mode.
7
STILL (Page 42)
Used to see still images.
8
V.KEYSTONE (Page 46)
You can use this function for trapezoidal
adjustment of the image.
9
QUICK (Page 56)
Used to quickly select the previous menu.
13
2
14
3
4
5
15
6
7
8
9
10
11
16
17
18
19
20
10 MENU
Used to display Menu Screen.
11 …†œ√ (Move) /
(Select)
Used to move to or select each menu item.
Projector and Accessories
ON
Used to turn on the projector.
Preparation
1
1
12 OFF
Used to turn off the projector.
13 LIGHT (Page 13)
Used to operate remote control in dark
room.
14 PC (Pages 25, 60, 62~66)
Used to switch to PC Mode.
15 DVI (Page 25, 60)
Used to switch to DVI Mode.
16 COMPOSITE (Pages 23, 26)
Used to switch to COMPOSITE Mode.
17 CUSTOM (Page 31)
Used to select Picture User Adjust Mode.
18 INSTALL (Page 44)
Used to flip or reverse the projected image.
19 INFO (Page 49)
Used to check source signals, picture setup,
PC screen adjustment and lamp lifespan.
20 EXIT
Used to make Menu Screen disappear.
11
PROJECTOR AND ACCESSORIES
Operating the Remote Control
Operating Move/Select Button
Preparation
Projector and Accessories
Move Menu Item (Up)
Move Menu Item
(Down)
Setting the Adjustment
(left), or move to
upper item
Select the current
setting
Inserting Batteries into Remote Control
1. Press on the
part of the lid to remove it.
2. Insert two AAA-sized 1.5V batteries by
matching +/-.
3. Close the lid.
12
Setting the Adjustment
(right), or move to
lower item.
Allowable range & angle of receiving the remote control signal
The remote control is effective within a 30°
angle 23~33 ft (7~10m) from the projector.
CAUTION
■
■
Preparation
■
Projector and Accessories
Keep used batteries away from children and
dispose of them properly.
Do not use new and used batteries together.
Replace two batteries at the same time.
Remove batteries when the projector is not
used for long periods of time.
Using Remote Control in Dark Place (LIGHT)
Press the LIGHT button of the remote
controller for five seconds. The remote
control buttons are lit for about 5 seconds
and turn off automatically.
LIGHT
13
INSTALLATION AND BASIC ADJUSTMENTS
Installation and Turning On
To Install the Projector
Install the projector so that the projection is
perpendicular to the screen.
Preparation
■
NOTE
■
■
Center the lens to the screen. If the projector
is not positioned perpendicular to the
screen, the image may appear trapezoidal.
Do not install the screen in a bright place as
it makes it harder to see the screen.
Darken the room when installing the
projector in a bright place.
Installation and Basic Adjustments
Installing Projector on Backside of Screen
Install a translucent screen to place the
projector on the backside of the screen.
The Translucent will show the horizontally
flipped image. Rotate the image (projected
from the projector) horizontally.
(Page 44)
Installing Projector in Front of the Screen
Install the projector at the viewers’ side.
■
NOTE
14
■
The projector may be installed on the ceiling
in front / back side of the screen.
When installing the projector on the ceiling,
contact your dealer.
Turning On Projector
1. Plug the power cord into the power terminal on the rear side of the projector.
3. Press the POWER button of the projector or the ON button of the remote control.
4. Screen display comes up in 30 seconds.
1
NOTE
■
3
When you turn off the projector, the cooling fan stops within 1 minute and 30 seconds.
When the cooling fan stops, push the power switch toward "O" and unplug the power cord.
Installation and Basic Adjustments
■
2
Preparation
2. Press and push the power switch on the rear side of the projector toward "-".
15
INSTALLATION AND BASIC ADJUSTMENTS
Zoom and Focus Adjustment
Using the Zoom Knob and the Focus Ring
1. You can adjust the size of image within zoom range by manipulating the Zoom Knob.
Preparation
Installation and Basic Adjustments
16
2. Focus the picture on the screen using the Focus Ring.
1
2
Zoom Knob
Focus Ring
Focus may appear dim if the projector is installed at a shorter than recommended distance. (Page 20)
NOTE
INSTALLATION AND BASIC ADJUSTMENTS
Leveling with Adjustable Feet
Using Adjustable Feet
For level placing of the projector, adjust the Adjustable Feet of the projector.
Preparation
■
NOTE
■
You may adjust the level of the projector up to 5 degrees.
Depending on the position of the projector, Keystone distortion of image may appear. (Page 46)
Installation and Basic Adjustments
Adjustable Feet
17
INSTALLATION AND BASIC ADJUSTMENTS
Using the Lens Shift Dial
Using the Lens Shift Dial
Move the picture projected on the screen up and down within the lens range by turning the
Lens Shift Dial on the top side of the projector with your fingers.
Preparation
Lens Shift Dial
Installation and Basic Adjustments
18
UP
DOWN
INSTALLATION AND BASIC ADJUSTMENTS
Screen Size and Projection Distance
Check the following before reading this manual.
Install the projector on a flat, even surface and level the projector using the adjustable feet
to realize optimal picture quality. If images are not clear, adjust them using the Zoom Knob
or Focus Ring, or move the projector forward and backward.
Screen Size (16:9)
Diagonal Image Size
(inch)
300
250
Vertical
(Y:cm/inch)
Min
(m/ft)
Max
(m/ft)
666.3/262.3
374.6/147.2
312.2/122.9
10.5/34.0
13.6/44.8
11.4/37.3
555.3/218.6
444.2/174.9
422.0/166.1
399.8/157.4
377.6/148.7
355.4/139.9
333.2/131.2
311.0/122.4
288.7/113.7
266.5/104.9
244.3/96.2
222.1/87.4
199.9/78.7
177.7/70.0
155.5/61.2
133.3/52.5
111.143.7
95.5/37.6
88.8/35.0
73.3/28.9
67.5/26.6
249.7/98.3
237.2/93.4
224.7/88.5
212.3/83.6
199.8/78.7
187.3/73.7
174.8/68.8
162.3/63.9
149.8/59.0
137.3/54.1
124.9/49.2
112.4/44.3
99.9/39.3
87.4/34.4
74.9/29.5
62.4/24.6
53.7/21.1
49.9/19.6
41.2/16.2
37.9/14.9
8.6/28.3
6.9/22.7
6.6/21.5
6.2/20.4
5.9/19.3
5.5/18.1
5.2/17.0
4.8/15.9
4.5/14.7
4.1/13.6
3.8/12.5
3.5/11.3
3.1/10.2
2.8/9.1
2.4/7.9
2.1/6.8
1.7/5.7
1.5/4.9
1.4/4.5
1.1/3.7
1.0/3.4
Distance from Lens Center
to Image Bottom
(Z’:cm/inch)
31.2/12.3
26.0/10.2
20.8/8.2
9.1/29.8
8.6/28.4
8.2/26.9
7.7/25.4
7.3/23.9
6.8/22.4
6.4/20.9
5.9/19.4
5.5/17.9
5.0/16.4
4.5/14.9
4.1/13.4
19.8/7.8
18.7/7.4
17.7/7.0
16.6/6.5
Installation and Basic Adjustments
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
43
40
33
30.385
Throw Distance (Z)
Horizontal
(X:cm/inch)
Preparation
SP-H700/SP-H710
15.6/6.1
14.6/5.7
13.5/5.3
12.5/4.9
11.4/4.5
10.4/4.1
9.4/3.7
8.3/3.3
3.6/11.9
3.2/10.4
7.3/2.9
6.2/2.4
2.7/9.0
2.3/7.5
5.2/2.0
4.5/1.8
1.9/6.4
1.8/6.0
4.2/1.7
3.4/1.3
1.5/4.9
1.4/4.5
3.2/1.3
This projector is designed to show images optimally on a 80 to 150 inch sized screen.
NOTE
Screen
Screen
Y
X
■
NOTE
■
Z : Throw Distance
Z' : Distance from Lens Center to Image Bottom
19
INSTALLATION AND BASIC ADJUSTMENTS
Screen Size and Projection Distance
SP-H500
Screen Size (16:9)
Diagonal Image Size
(inch)
Throw Distance (Z)
Preparation
Horizontal
(X:cm/inch)
Vertical
(Y:cm/inch)
Min
(m/ft)
Max
(m/ft)
200
442.8/174.3
420.6/165.6
398.5/156.9
249.1/98.1
236.6/93.1
6.8/22.4
190
180
170
8.8/28.5
8.3/27.1
160
Installation and Basic Adjustments
150
140
130
120
110
100
90
80
70
60
50
40
376.3/148.1
354.2/139.5
332.1/130.7
309.9/122.0
287.8/113.3
265.7/104.6
243.5/95.9
221.3/87.1
199.2/78.4
177.1/69.7
155.0/61.0
132.8/52.3
110.7/43.6
88.6/34.9
224.1/88.3
211.7/83.3
199.2/78.4
186.8/73.5
174.3/68.7
161.9/63.7
149.4/58.8
137.0/53.9
124.5/49.0
112.1/44.1
99.6/39.2
87.2/34.3
74.7/29.4
62.3/24.5
49.8/19.6
6.5/21.3
6.1/20.1
5.8/19.0
5.5/17.9
5.1/16.8
4.8/15.6
4.4/14.5
4.1/13.4
3.7/12.3
3.4/11.1
3.0/10.0
2.7/8.9
2.4/7.7
2.0/6.6
1.7/5.5
1.3/4.4
Distance from Lens Center
to Image Bottom
(Z’:cm/inch)
24.9/9.8
23.7/9.3
22.4/8.8
7.8/25.7
7.4/24.2
21.2/8.3
19.9/7.8
7.0/22.8
6.5/21.4
18.7/7.4
17.4/6.9
6.1/19.9
5.6/18.5
5.2/17.1
4.8/15.6
4.3/14.2
3.9/12.8
3.5/11.3
3.0/9.9
16.2/6.4
14.9/5.9
13.7/5.4
12.5/4.9
11.2/4.4
10.0/3.9
8.7/3.4
7.5/2.9
2.6/8.5
2.1/7.0
6.2/2.5
5.0/2.0
1.7/5.6
This projector is designed to show images optimally on a 80 to 150 inch sized screen.
NOTE
Screen
Screen
X
■
NOTE
20
■
Z : Throw Distance
Z' : Distance from Lens Center to Image Bottom
Y
V
I
S
U
A
L
R
E
A
L
I
S
M
Connections and Source Setup
Before Connections ....................................22
Connecting to Video Equipment ................23
Setting up the External Input Source ........26
Naming the External Connections ............27
Before Connections
Check the followings before connecting the projector to other devices.
Connections and Source Setup Before Connections
22
Check the following Before Connecting
1. Refer to the manual of the device the projector is connected to. The number and
position of ports may differ depending on type of devices.
2. Do not connect power until all the connections are completed. If you try to connect
power while connecting cables, it may result in damage to the projector.
3. Check the type of ports the projector is connected to.
Refer to "Rear Side and Cables" on page 10 for cables used for connection.
CONNECTING TO VIDEO EQUIPMENT
Connecting to VCR/Camcorder/Cable Box
Rear side of Projector
Video (Composite) Cable
or
VCR
Camcorder
Rear Connection
Cable Box
Connect COMPOSITE (yellow) input port of the projector to the VIDEO OUT
(yellow) port of video equipment using the video cable.
■
If the video equipment has S-VIDEO OUT port, connect it to S-VIDEO input port of the projector.
Connections and Source Setup Connecting to Video Equipment
S-Video Cable
Viewing the picture
COMPOSITE
1
S-VIDEO
2
on the projector and press the
1 Turn
COMPOSITE button to select Composite.
Composite
the projector and the video
2 Connect
equipment via S-Video cable and press the
S-VIDEO button to select S-Video.
■
When Composite Mode is not available, check the
video cables are in place.
■
NOTE
■
Check that the projector and the video
equipment are turned off before connecting
cables.
This projector does not support sound.
(Separate audio system is needed for sound.)
23
CONNECTING TO VIDEO EQUIPMENT
Connecting to DVD
Rear side of Projector
Connections and Source Setup Connecting to Video Equipment
Component Cable
DVD
S-VIDEO OUT
COMPONENT VIDEO OUT
AUDIO OUT
Rear Connection
Connect COMPONENT1 or COMPONENT2 (Y/Pb/Pr) ports of the projector to
Component port on the rear side of DVD using Component Cable.
Viewing the picture
COMP.1
1
COMP.2
2
on the projector and press the COMP.1
1 Turn
button to select Component1.
Press the COMP.2 button to select
2 Component2
if COMPONENT2 is connected.
■
When Component Mode is not available, check that
the component cables are in place.
NOTE
24
Component Ports are marked as (Y, Pb,Pr),
(Y, B-Y, R-Y) or (Y, Cb, Cr) depending on
the manufacturer.
Component1
CONNECTING TO VIDEO EQUIPMENT
Connecting to the Digital TV Receiver
Rear side of Projector
DVI Video Cable
or
Digital TV Receiver
(Set-Top Box)
Rear Connection
Connect antenna cable to antenna
signal input terminal of the receiver.
1
2
Connect COMPONENT1 or
COMPONENT2 (Y/Pb/Pr) port of the
projector to Component port of the
receiver using Component Cable.
■
If the receiver has DVI or PC OUT port,
you can connect it to DVI or PC input
port of the projector.
Connections and Source Setup Connecting to Video Equipment
PC Video Cable
Component Cable
Viewing the picture
COMP.1
1
on the projector and press the COMP.1
1 Turn
button to select Component1.
Component1
COMP.2
2
PC
DVI
Press the COMP.2 button to select
2 Component2
if COMPONENT2 is connected.
If the receiver is connected to DVI or PC port,
press the DVI or PC button to select DVI or PC
respectively.
■
DVI
When Component Mode is not available, check that
the component cables are in place.
25
Setting up the External Input Source
You can select a device connected to the projector to display.
Press the desired source button (COMP.1/
COMP.2/ S-VIDEO/COMPOSITE/ PC/DVI).
Connections and Source Setup Setting up the External Input Source
Pressing a button switches to the respective mode.
You can not switch to the mode if the projector is not
connected to the respective device.
One Touch
MENU
1
Select
2, 3, 4
…/†
4
EXIT
5
1
Press the MENU button.
2
Press the
The main menu is displayed.
button to select Input.
The Input menu is displayed.
Input
3
Press the
button to select Source List.
The Source List menu is displayed.
Move
4
Press the ▲ or ▼ button to move to desired input
mode, then press the
button.
The source input you chose is displayed.
If the input mode is not selected, check that cables are in place.
5
Press the EXIT button to exit the menu.
Enter
Return
Source List
Component1
Component2
S-Video
Composite
PC
DVI
Move
26
: Component1 √
√
Source List
Edit Name
Enter
:---:---:---:---:---:---Return
Naming the External Connections
You can select and set up the type of device you want to connect to the projector.
1
Select
2, 3, 4, 5
…/†
3, 4,5
EXIT
6
1
Press the MENU button.
2
Press the
The main menu is displayed.
button to select Input.
The Input menu is displayed.
Input
: Component1 √
√
Source List
Edit Name
3
Press the ▲ or ▼ button to move to Edit Name,
then press the
button.
The Edit Name menu is displayed.
Move
Enter
Return
Edit Name
4
Component1
Component2
S-Video
Composite
PC
DVI
Press the ▲ or ▼ button to move to edited input
mode, then press the
button.
Move
5
6
Press the ▲ or ▼ button to move to desired
device, then press the
button.
Setup is switched to the selected device.
√
√
√
√
√
√
:---:---:---:---:---:----
Enter
Connections and Source Setup Naming the External Connections
MENU
Return
Edit Name
Component1
Component2
S-Video
Composite
PC
DVI
: - - -- -- - : - - - VCR
: - - - DVD
: - - -Cable
HD
:---Satellite
:----
√
√
√
√
√
√
AV Receiver
†
Press the EXIT button to exit the menu.
Move
Enter
Return
27
Picture Adjustment
V
I
S
U
A
L
R
E
A
L
I
S
M
Picture Adjustment
Selecting Picture Mode ..............................30
Custom Settings of the Picture ..................31
Changing the Color Standard ....................32
Selecting and Adjusting Color
Temperature ................................................33
Gamma Correction ......................................34
Saving Custom Picture Settings ................35
Setting up DNIe ..........................................36
Selecting Picture Size..................................37
Screen Position Adjustment ......................39
Film Mode ....................................................40
Overscan ......................................................41
Still Picture ..................................................42
Selecting Picture Mode
Press the P.MODE button.
Each press of the button, picture mode is switched to
Dynamic, Standard, Movie1, Movie2, User1, User2,
User3 and Custom.
One Touch
MENU
1
Picture Adjustment
Select
3, 4
…/†
2, 4
Standard
EXIT
5
Selecting Picture Mode
1
Press the MENU button.
2
Press the ▲ or ▼ button to move to Picture.
3
The main menu is displayed.
The Picture menu is displayed.
Press the
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
button.
The Picture Mode is selected.
Move
: Movie 1
: Full
: Off
: On
: On
Enter
√
√
√
√
√
√
√
Return
Picture
4
Press the
button again.
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Setup is switched to the selected mode.
Move
5
: Off
: On
: On
Movie1
Movie2
User1
User2
User3
Custom
√
√
√
Return
Press the EXIT button to exit the menu.
Picture
Modes
Dynamic
Standard
Movie1
Movie2
30
Enter
Dynamic
: Movie
1
√
Standard √
:
Color
Temperature
9300K
8000K
6500K
5500K
Gamma
Gamma Mode3: Graphic Mode
Gamma Mode2: Video Mode
Gamma Mode1: Film Mode
NOTE
User 1, 2, and 3 Saving
Options are designed
for setup and storage of
various users’
customized picture
modes.
Custom Settings of the Picture
You can adjust Contrast, Brightness, Sharpness, Color and Tint of the picture as desired.
Press the CUSTOM button.
The Custom Picture menu is displayed.
Refer to number 4 below to make adjustments.
One Touch
MENU
Custom Picture
1
Select
2, 3, 4
50
50
50
50
R 50
Picture Adjustment
Contrast
Brightness
Sharpness
Color
Tint
G 50
† More
…/†/œ/√
Move
Enter
Return
2, 3, 4
EXIT
5
1
3
4
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
button.
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Press the ▲ or ▼ button to move to Custom
Picture, then press the
button.
The Custom Picture menu is displayed.
Move
Enter
: Full
: Off
: On
: On
Return
Custom Picture
Press the ▲ or ▼ button to move to desired item,
then press the
button.
Press the œ or √ button to adjust the selected
item.
Contrast
Brightness
Sharpness
Color
Tint
G 50
50
50
50
50
R 50
† More
Move
5
√
√
√
√
√
√
√
: Movie 1
Custom Settings of the Picture
2
Press the MENU button.
Press the EXIT button to exit the menu.
…
Contrast
†
Enter
Return
50
Custom Picture Menu
Contrast
Brightness
Sharpness
Color
Tint
Used to adjust the contrast between the object
and the background.
Used to adjust brightness of the entire picture.
Used to adjust the outlines of the object
sharper or less sharp.
Used to adjust color lighter or deeper.
Used to obtain more natural color of objects
using Green or Red enhancement.
NOTE
You cannot adjust tint
when the input of
COMPONENT1 and
COMPONENT2 are set
at 480p, 720p and
1080i.
31
Changing the Color Standard
You may adjust the color standard to suit the color standard of the input signal.
Color Standard
SMPTE_C Standardized for Video Equipment by the
Society of Motion Picture and Television
Engineers
HD
High Definition, 1125 scan lines, standard
definition TV submitted to the ITU-R by
U.S., Japan and Canada, in 1986.
EBU
Regulations and standards for European
Broadcasting Production and Technology,
standardized by the European
Broadcasting Union.
MENU
1
Picture Adjustment
Select
2, 3, 4, 5
…/†/œ/√
2, 3, 4, 5
ATSC
PAL,
SECAM
EXIT
6
1
Changing the Color Standard
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
Picture
button.
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Press the ▲ or ▼ button to move to Custom
Picture, then press the
button.
The Custom Picture menu is displayed.
Move
√
√
√
√
√
√
√
: Movie 1
: Full
: Off
: On
: On
Enter
Return
Custom Picture
4
… More
Color Standard : SMPTE_C
Color Temperature
Gamma
: Gamma Mode1
Save
Press the ▲ or ▼ button to move to Color
Standard, then press the
button.
The Color Standard menu is displayed.
Move
5
Press the œ or √ button to adjust the selected
item.
6
Press the EXIT button to exit the menu.
Enter
√
√
√
√
Return
Color Standard
SMPTE_C
Move
32
NTSC
HD
Enter
EBU
Return
Selecting and Adjusting Color Temperature
You can change tint of the entire screen to suit your needs.
Color Temperature Menu
MENU
1
Select
2, 3, 4, 5, 6
…/†/œ/√
2, 3, 4, 5, 6
EXIT
7
1
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
Picture
button.
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Press the ▲ or ▼ button to move to Custom
Picture, then press the
button.
The Custom Picture menu is displayed.
Move
√
√
√
√
√
√
√
: Movie 1
: Full
: Off
: On
: On
Enter
Return
Custom Picture
4
… More
Color Standard : SMPTE_C
Color Temperature
Gamma
: Gamma Mode1
Save
Press the ▲ or ▼ button to move to Color
Temperature, then press the
button.
The Color Temperature menu is displayed.
Move
5
6
Press the œ or √ buttons to select an option then
press the
button.
Enter
√
√
√
√
Return
Color Temperature
9300K
The selected option is applied.
Move
Press the ▲ or ▼ buttons to select an option then
press the
button. Press the œ or √ buttons to
adjust the selected item.
…
R-Gain
†
8000K
6500K
Enter
Selecting and Adjusting Color Temperature
2
Picture Adjustment
5500K Used to deliver optimal image quality for
black-and-white films. Color temperature of
the picture mode of Movie2 is set to 5500K.
6500K This temperature is used for the most video
productions. It is set as Movie1 when it is
manufactured, and may deliver the most precise tint.
8000K This mode is applied to bright places such as
showrooms and other sales outlet. Sharpness and
brightness are enhanced. It is suitable for brighter
environments and is set to the Dynamic Mode.
9300K With both Sharpness and Brightness enhanced, this
dynamic mode can be effectively used in bright
ambient light conditions.
5500K
Return
50
A separate adjustment window appears for making the adjustment.
7
Press the EXIT button to exit the menu.
33
Gamma Correction
Gamma is used to improve the picture quality with color balance.
MENU
1
Picture Adjustment
Select
2, 3, 4, 5
…/†
2, 3, 4, 5
EXIT
6
1
Gamma Correction
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
Picture
button.
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Press the ▲ or ▼ button to move to Custom
Picture, then press the
button.
The Custom Picture menu is displayed.
Move
Enter
: Movie 1
: Full
: Off
: On
: On
√
√
√
√
√
√
√
Return
Custom Picture
4
Press the ▲ or ▼ button to move to Gamma,
then press the
button.
5
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
… More
Color Standard : SMPTE_C
Color Temperature
Gamma
: Gamma Mode1
Save
Move
Enter
√
√
√
√
Return
Custom Picture
… More
Color Standard : SMPTE_C
√
Color Temperature
√
Gamma
: Gamma
GammaMode1
Mode1
Gamma Mode2
Save
Setup is switched to the selected mode.
Gamma Mode3
6
Move
Press the EXIT button to exit the menu.
NOTE
34
Enter
Return
Refer to page 30 for
information on Gamma
Mode1, 2, and 3.
Saving Custom Picture Settings
Used to save custom picture (Contrast, Brightness, Sharpness, Color, Tint, Color Temperature
and Gamma) settings.
MENU
1
Picture Adjustment
Select
2, 3, 4, 5, 6
…/†/œ/√
2, 3, 4, 5, 6
EXIT
7
1
3
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
Picture
button.
Press the ▲ or ▼ button to move to Custom
Picture, then press the
button.
The Custom Picture menu is displayed.
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
√
√
√
√
√
√
√
: Movie 1
: Full
: Off
: On
: On
Enter
Return
Custom Picture
4
Press the ▲ or ▼ button to move to Save, then
press the
button.
The Save menu is displayed.
… More
Color Standard : SMPTE_C
Color Temperature
Gamma
: Gamma Mode1
Save
Move
5
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
6
Press the œ or √ button to move to OK, then
press the
button.
Setup is switched to the selected mode.
Enter
NOTE
Return
Save
√
√
√
User1
User2
User3
Move
Enter
Return
Save
Save Current Setting to User1?
Cancel
OK
7
√
√
√
√
Saving Custom Picture Settings
2
Press the MENU button.
Move
Enter
Return
Press the EXIT button to exit the menu.
The User1, User2 and User3 modes are saved differently
according to external input sources (Component1/ Component2/
S-Video/Composite/PC/DVI).
35
Setting up DNIe
DNIe (Digital Natural Image engine) is an image enhancing function developed by Samsung
Electronics. It enables users to enjoy brighter, sharper and more dynamic pictures.
MENU
1
Picture Adjustment
Select
2, 3, 4
…/†
2, 3, 4
EXIT
5
1
Setting up DNIe
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to DNIe, then
press the
button.
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
4
5
Press the ▲ or ▼ button to move to On, then
press the
button.
Setup is switched to the selected mode.
DNIe Mode
Off
DNle Mode Off
Demo DNle On/Off Picture Comparison Mode
On
DNle Mode On
36
: Full
: Off
: On
: On
Enter
√
√
√
√
√
√
√
Return
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
Press the EXIT button to exit the menu.
: Movie 1
Enter
: Movie 1
: Full
: Off
: On
: On
√
√
√
√
Off
Demo
On
Return
Selecting Picture Size
Press the P.SIZE button.
Each press of the button, picture size is switched to Full,
Zoom1, Zoom2 and 4:3.
One Touch
MENU
1
Picture Adjustment
Select
2, 3, 4
…/†
2, 3, 4
EXIT
5
1
3
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Picture Size,
then press the
button.
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
4
5
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
Setup is switched to the selected mode.
: Movie 1
: Full
: Off
: On
: On
Enter
√
√
√
√
√
√
√
Selecting Picture Size
2
Press the MENU button.
Return
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
Enter
: Movie 1
:
: Off
: On
: On
√
√
Full
Zoom1
Zoom2
4:3
Return
Press the EXIT button to exit the menu.
37
Supported Picture Sizes
O : Supported Modes
X : Unsupported Modes
Picture Adjustment
Selecting Picture Size
Refer to page 58 for display modes supported.
NOTE
38
Screen Position Adjustment
Adjust the screen position if the edges are not aligned.
MENU
1
Picture Adjustment
Select
2, 3
…/†/œ/√
2, 3, 4
EXIT
5
1
3
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
button.
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Press the ▲ or ▼ button to move to Position,
then press the
button.
Move
4
√
√
√
√
√
√
√
: Movie 1
: Full
: Off
: On
: On
Enter
Return
Position
Press the ▲, ▼, œ, or √ buttons to adjust the
position.
Screen Position Adjustment
2
Press the MENU button.
…
œ
√
The Screen is moved and set in the selected position.
†
5
Move
Return
Press the EXIT button to exit the menu.
NOTE
The respective position
information is set and
stored automatically to
the corresponding
external input modes
(Component1,2 /
S-Video, Composite /
PC / DVI).
39
Film Mode
Supports enhanced screen quality for films of 24 frames.
MENU
1
Picture Adjustment
Select
2, 3, 4
…/†
2, 3, 4
EXIT
5
1
Film Mode
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Film Mode,
then press the
button.
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
4
5
40
Press the ▲ or ▼ button to move to On, then
press the
button.
Setup is switched to the selected mode.
: Full
: Off
: On
: On
Enter
√
√
√
√
√
√
√
Return
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
Press the EXIT button to exit the menu.
: Movie 1
Enter
: Movie 1
: Full
: Off
: On
: On
Off
On
√
√
√
√
√
√
√
Return
Overscan
Used to display raw input signals from 480p, 576p, 720p, 1080i HD sources or scale to fit to 1280 x
720 resolution after cutting out certain boundaries using software scaling.
MENU
1
Picture Adjustment
Select
2, 3, 4
…/†
2, 3, 4
EXIT
5
1
3
The main menu is displayed.
Press the ▲ or ▼ button to move to Picture.
The Picture menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Overscan,
then press the
button.
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
4
5
Overscan
2
Press the MENU button.
Press the ▲ or ▼ button to move to On, then
press the
button.
Setup is switched to the selected mode.
: Movie 1
: Full
: Off
: On
: On
Enter
√
√
√
√
√
√
√
Return
Picture
Picture Mode
Custom Picture
Picture Size
Position
DNIe
Film Mode
Overscan
Move
Enter
: Movie 1
: Full
: Off
: On
: On
Off
On
√
√
√
√
√
√
√
Return
Press the EXIT button to exit the menu.
41
Still Picture
Used to pause playback to see a still picture.
Press the STILL button.
Each press of the button pauses and resumes play back.
One Touch
Picture Adjustment
Still Picture
42
V
I
S
U
A
L
R
E
A
L
I
S
M
Setup
Flipping/Reversal of Projected Image ....44
Light Setting ................................................45
Correcting Vertical Keystone ....................46
Test Patterns ..............................................47
Restoring the Factory Default Settings....48
Information ..................................................49
Flipping/Reversing the Projected Image
To support positioning of the projector, horizontal/vertical flipping and picture reversal are available.
Press the INSTALL button.
The screen will flip over horizontally or vertically with each
press of the button.
One Touch
MENU
Front-Ceiling
1
Front-Floor
Select
3, 4
…/†
Rear-Ceiling
2, 4
EXIT
roolF-raeR
Setup
5
Flipping/Reversing the Projected Image
1
Press the MENU button.
2
Press the ▲ or ▼ button to move to Setup.
3
The main menu is displayed.
The Setup menu is displayed.
Press the
Setup
button.
Install is selected.
Move
Enter
Return
Setup
4
Press the
button again.
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Setup is switched to the selected mode.
Move
5
Enter
Front-Floor √
: Front-Floor
Front-Ceiling√
: Theater
Rear-Floor
√
Rear-Ceiling
√
√
√
√
Return
Press the EXIT button to exit the menu.
Install Menu
Front-Floor
Front-Ceiling
Rear-Floor
Rear-Ceiling
44
: Front-Floor √
: Theater
√
√
√
√
√
√
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Normal Image
Horizontally Reversed Image
Vertically Reversed Image
Horizontal/Vertical Reversed Image
NOTE
This function is used to
set up reversed image
projection for ceiling
installation. To install
projector, refer to page
14.
Light Setting
Used to set the image brightness by adjusting the amount of light generated by the lamp.
MENU
1
Select
2, 3, 4
…/†
2, 3, 4
EXIT
Setup
5
1
3
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Light
Setting, then press the
button.
The Light Setting menu is displayed.
4
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
5
Press the EXIT button to exit the menu.
Setup
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Move
Enter
: Front-Floor √
: Theater
√
√
√
√
√
√
Light Setting
2
Press the MENU button.
Return
Light Setting
√
√
Theater
Bright
Setup is switched to the selected mode.
Move
Enter
Return
Light Setting Mode
Theater
Bright
Used to reduce the brightness of the lamp in dark
ambient light to prevent reflection in the eye. It also
lowers power consumption and extends the life of the
lamp.
Used to enhance the brightness in relatively bright
ambient light.
45
Correcting Vertical Keystone
Used to compensate image shape when image distortion occurs.
Press the V.KEYSTONE button.
Press the œ or √ button to adjust picture image optimally.
One Touch
MENU
1
Select
2, 3
…/†/œ/√
2, 3
EXIT
Setup
4
1
Correcting V-Keystone
2
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Setup
3
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Press the ▲ or ▼ button to move to V-Keystone,
then press the
button.
Press the œ or √ button to adjust.
Move
4
Return
Press the EXIT button to exit the menu.
V-Keystone
NOTE
46
Enter
: Front-Floor √
: Theater
√
√
√
√
√
√
0
V-Keystone corrects
distortion of picture
image by software.
It is better to install the
projector properly to
avoid distortion instead
of using the V-Keystone
feature.
Test Patterns
Generated by the projector itself. Utilized as installation basis for better installation of the projector.
MENU
1
Select
2, 3, 4
…/†
2, 3, 4
EXIT
Setup
5
1
3
4
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
Setup
The Setup menu is displayed.
Press the
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
button.
Press the ▲ or ▼ button to move to Test Pattern,
then press the
button.
Move
Enter
: Front-Floor √
: Theater
√
√
√
√
√
√
Return
Test Pattern
The Test Pattern menu is displayed.
√
√
√
√
√
√
Crosshatch
Screen Size
Color Standard
Red
Green
Blue
Press the ▲ or ▼ button to move to desired
pattern, then press the
button.
Test Patterns
2
Press the MENU button.
† More
The selected pattern is displayed.
Move
Enter
Return
Test Pattern
5
… More
White
6500K_White
Press the EXIT button to exit the menu.
Test Pattern Menu
You can check whether the picture is distorted or not.
You can refer to picture format sizes such as 1.33:1
or 1.78:1.
Color Standard You can see the change in colours by switching
between SMPTE_C, HD and EBU Colour
Standards. Refer to page 32.
Red
Red Screen, only for color adjustment.
Green
Green Screen, only for color adjustment.
Blue
Blue Screen, only for color adjustment.
White
White Screen, only for color adjustment.
6500K_White White Screen, shows brightest white color possible.
Move
Crosshatch
Screen Size
NOTE
Enter
√
√
Return
The Crosshatch and
Screen Size patterns of
this projector are
provided by JKP (JK
Production).
The Red/Green/Blue
colors of the test
patterns are only for the
color adjustment
procedures, and may
not comply with the
actual colors displayed
during video playback.
47
Restoring the Factory Default Settings
Used to restore setting values to factory defaults.
MENU
1
Select
2, 3, 4
…/†/œ/√
2, 3, 4
EXIT
Setup
5
1
Restoring the Factory Default Settings
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Setup
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Press the ▲ or ▼ button to move to Factory
Default, then press the
button.
Move
Enter
Return
Factory Default
4
Press the œ or √ button to move to OK, then
press the
button.
Back to Factory Default setting?
Move
5
Cancel
OK
Setting values are returned to factory defaults.
Enter
Return
Press the EXIT button to exit the menu.
NOTE
48
: Front-Floor √
: Theater
√
√
√
√
√
√
User settings including
Edit Name and Custom
Picture will be reset.
Information
You can check external source signals, picture setup, PC picture adjustment and lamp use time.
Press the INFO button.
Information
One Touch
MENU
Input Source
: PC
Picture Mode
: Movie1
Picture Size
: Full
Brightness
: 50
Contrast
: 50
Color Temperature : 6500K
R-Gain
: 50
G-Gain
: 50
B-Gain
: 50
R-Offset
:0
G-Offset
:0
B-Offset
:0
1
Select
Color standard
DNIe
Install
Light Setting
V-Keystone
Coarse
Fine
Resolution
H-Frequency
V-Frequency
Lamp Time
2, 3
: EBU
: On
: Front-Floor
: Theater
:0
: 1344
: 101
: 1024X768
: 31KHz
: 70Hz
: 0 Hour
OK
…/†
2, 3
EXIT
4
1
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
Setup
2
Press the MENU button.
button.
Setup
3
Press the ▲ or ▼ button to move to Information,
then press the
button.
You can check external source signals, picture setup, PC picture
adjustment and lamp use time.
Move
Enter
Return
Information
Press the EXIT button to exit the menu.
Input Source
: PC
Picture Mode
: Movie1
Picture Size
: Full
Brightness
: 50
Contrast
: 50
Color Temperature : 6500K
R-Gain
: 50
G-Gain
: 50
B-Gain
: 50
R-Offset
:0
G-Offset
:0
B-Offset
:0
Color standard
DNIe
Install
Light Setting
V-Keystone
Coarse
Fine
Resolution
H-Frequency
V-Frequency
Lamp Time
: EBU
: On
: Front-Floor
: Theater
:0
: 1344
: 101
: 1024X768
: 31KHz
: 70Hz
: 0 Hour
Information
4
: Front-Floor √
: Theater
√
√
√
√
√
√
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
OK
49
V
I
S
U
A
L
R
E
A
L
I
S
M
Menu Option
Setting the Language..................................52
Setting the Menu Position..........................53
Setting the Menu Translucency ..................54
Setting the Menu Display Time..................55
Selecting the Quick Menu ..........................56
Setting the Language
You can select the language used for the menu screen.
MENU
1
Select
3, 4
…/†
2, 4
EXIT
5
Menu Option
1
Press the MENU button.
2
Press the ▲ or ▼ button to move to Menu Option.
Setting the Language
3
The main menu is displayed.
The Menu Option menu is displayed.
Press the
button.
Menu Option
Language
: English
Menu Position
Menu Translucency : Opaque
Menu Display Time : 120 sec
The Language is selected.
Move
Enter
Return
Menu Option
4
Press the
button again.
Press the ▲ or ▼ button to move to desired
language, then press the
button.
English
Language
: English
Deutsch
Menu Position
Nederlands
Menu Translucency : Opaque
Menu Display Time : 120Español
Sec
Français
Italiano
Svenska
Setup is switched to the selected language.
†
Move
5
52
√
√
√
√
Press the EXIT button to exit the menu.
Enter
Return
Setting the Menu Position
You can move Menu Position to up/down/left/right.
MENU
1
Select
2, 3
…/†/œ/√
2, 3, 4
EXIT
5
2
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Menu Option.
The Menu Option menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Menu
Position, then press the
button.
Menu Option
Move
4
Press the ▲, ▼, œ, or √ button to move to
desired position.
The menu screen is displayed on the given position.
√
√
√
√
Language
: English
Menu Position
Menu Translucency : Opaque
Menu Display Time : 120 sec
Enter
Return
Menu Position
…
œ
√
†
5
Move
Setting the Menu Position
3
Menu Option
1
Return
Press the EXIT button to exit the menu.
53
Setting the Menu Translucency
You can set the translucency of menu.
MENU
1
Select
2, 3, 4
…/†
2, 3, 4
EXIT
5
Menu Option
1
2
Setting the Menu Translucency
54
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Menu Option.
The Menu Option menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Menu
Translucency, then press the
button.
Menu Option
Language
: English
Menu Position
Menu Translucency : Opaque
Menu Display Time : 120 sec
Move
4
5
Press the ▲ or ▼ button to move to desired
mode, then press the
button.
Setup is switched to the selected mode.
Return
Menu Option
Language
: English
Menu Position
Opaque
Menu Translucency : Opaque
High
Menu Display Time : 120 Sec
Medium
Low
Move
Press the EXIT button to exit the menu.
Enter
√
√
√
√
Enter
Return
Setting Up the Menu Display Time
You can set the display time of the menu.
MENU
1
Select
2, 3, 4
…/†
2, 3, 4
EXIT
5
2
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Menu Option.
The Menu Option menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to Menu
Display Time, then press the
button.
Menu Option
Language
: English
Menu Position
Menu Translucency : Opaque
Menu Display Time : 120 sec
Move
4
5
Press the ▲ or ▼ button to move to desired time,
then press the
button.
Setup is switched to the selected time.
Return
Menu Option
5
Language
: English
10
Menu Position
30
Menu Translucency : Opaque
60
Menu Display Time : 120 Sec
90
120
Stay On
Move
Press the EXIT button to exit the menu.
Enter
√
√
√
√
Enter
Return
Setting Up the Menu Display Time
3
Menu Option
1
55
Selecting the Quick Menu
Press the QUICK button.
The menu you used previously will appear.
One Touch
Menu Option
Selecting the Quick Menu
56
V
I
S
U
A
L
R
E
A
L
I
S
M
Connecting to PC
Before Connecting to PC ............................58
Setting up the PC Environment..................59
Connecting to PC ........................................60
Automatic Picture Adjustment ..................62
Frequency Adjustment ................................63
Fine Tuning with the Phase Adjustment....64
Zooming the Screen ....................................65
Reset the PC ................................................66
Before Connecting to PC
Check the following before connecting the projector to a PC.
Check the following before connecting:
■
Adjust the PC display setting to the resolution and frequency supported by the
projector.
■
Refer to the PC user manual (graphic and sound card) when connecting the projector
to PC.
■
Do not connect power cord until all connections are completed. It may result in
damage to the product if you connect power during connection.
■
Check the graphic card port type installed in PC.
Connecting to PC
Display modes supported by this projector
Mode
Source
Resolution
(H x V)
Before Connecting to PC
800 x 449
832 x 445
900 x 449
720 x 400
936 x 446
800 x 525
640 x 480
864 x 525
832 x 520
840 x 500
832 x 509
1024 x 625
800 x 600
1056 x 628
1040 x 666
1056 x 625
1048 x 631
1152 x 667
832 x 864
1024 x 768 1344 x 806
1328 x 806
1312 x 800
1280 x 1024 1688 x 1066
1920 x 1080i 2200 x 1125
2640 x 1125
1280 x 720p 1650 x 750
1980 x 750
858 x 525
720 x 480p
720 x 576
720 x 576p
858 x 525
720 x 480i
864 x 625
720 x 576i
640 x 350
VGA
PC
&
DVI
SVGA
XGA
SXGA
PC
&
DVI
&
Component
HD
Component
SD
Total
Resolution
Sync Type
Horizontal Sync
Vertical Sync
Pixel
SOG
Frequency
Frequency
Clock
Separate Composite (Sync-On
Polarity
Polarity
[Hz]
[KHz]
[MHz]
-Green)
31.47
37.86
31.47
37.93
31.47
35.00
37.86
37.5
43.27
35.16
37.88
48.08
46.87
53.67
49.73
48.36
56.4
60.02
63.981
33.75
28.125
45
37.5
31.5
31.25
15.73
15.625
P
P
N
N
N
N
N
N
N
N/P
P
P
P
P
N
N
N
P
P
X
X
X
X
X
X
X
X
70
85.1
70
85
60
66.7
72.8
75
85
56.3
60.3
72.2
75
85.1
74.6
60
70.1
75
60.02
60
50
60
50
60
50
60
50
N
N
P
P
N
N
N
N
N
N/P
P
P
P
P
N
N
N
P
P
X
X
X
X
X
X
X
X
25.175
31.5
28.322
35.5
25.175
30.24
31.5
31.5
36
36
40
50
49.5
56.25
57.284
65
75
78.75
108
74.25
74.25
74.25
74.25
27
27
13.5
13.5
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
SOY
SOY
SOY
SOY
SOY
SOY
SOY
SOY
The table complies to IBM/VESA requirements and is based on analog signal input.
NOTE
Refer to "Rear Side and Cables" on page 10 for cables used for connection.
58
Setting up the PC Environment
the right mouse button on the Windows wallpaper
1 Click
and click on Properties.
1
Display Properties tab will appear.
on Settings tab and set the Screen resolution by
2 Click
referring to Resolution described in the display mode
table supported by this projector.
■
You do not have to change Color quality setup.
on Monitor tab and set the Screen refresh rate by
4 Click
referring to Vertical Frequency described in the display
mode table supported by this projector.
■
3
Set up both the vertical and horizontal frequency instead of Screen
refresh rate.
4
The computer might begin restart automatically.
6 Shut down the PC and connect to the projector. (Page 60)
■
NOTE
■
■
■
■
Setting up the PC Environment
the OK button to close the window and press the OK
5 Press
button in Display Properties window to close.
■
2
Connecting to PC
the Advanced button.
3 Press
Another property window will appear.
Process might vary depending on the type of computers or Windows versions.
This appliance supports up to 32 bits per pixel in Color quality when it is used as a PC monitor.
Projected images may differ from the monitor depending on monitor manufacture or Windows versions.
If a band or an unusual signal appears on the projector when PC is turned off or disconnected, switch to Composite
mode using the SOURCE button or check that PC is properly connected.
When connecting the projector to PC (including DVI connection), check that PC setup complies to display settings
supported by this projector. If not, there may be signal problems.
59
Connecting to PC
You can connect a PC to the projector and use it as a monitor.
Using PC Video Cable or DVI Cable
Rear side of Projector
Rear Connection
DVI-D Video
Cable
PC Video
Cable
or
Connecting to PC
DVI-D Port
Connect PC (RGB In) port on the rear side of the projector to the monitor output port
of PC using PC video cable.
1
■
If PC has a DVI output port, connect it to DVI port of the projector.
Connecting to PC
This product supports Plug & Play. No driver installation is needed for Windows XP.
NOTE
Viewing the PC Screen
PC
1
on the projector and press the PC button
1 toTurnselect
PC. If the projector is connected to
PC
DVI, press the DVI button to select DVI.
■
If PC Mode is not available, check PC video cable is
in place.
on the PC and set the PC Environment
2 Turn
when necessary. (Page 59)
3 Adjust the screen. (Pages 62~65)
■
NOTE
■
■
60
Enjoy better picture quality by using DVI-D cable (supports digital signals only)
instead of PC Video cable.
DVI-I cable (supports analog signals) is not supported. Use DVD-D cable.
Sound comes out from PC speakers.
Pin Configuration of PC Video Port Plug
PC Video Cable
(15-pin signal)
Pin No.
PC Input
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
Signal
T.M.D.S. DATA2T.M.D.S. DATA2+
T.M.D.S. DATA2/4 Shield
T.M.D.S. DATA4T.M.D.S. DATA4+
Clock (DDC)
Data (DDC)
No Connection
T.M.D.S. DATA1T.M.D.S. DATA1+
T.M.D.S. DATA1/3 Shield
T.M.D.S. DATA3-
VESA Plug & Play
This appliance supports VESA Plug & Play and
recognizes connection to PC automatically.
Pin No.
13
14
15
16
17
18
19
20
21
22
23
24
CAUTION
Signal
T.M.D.S. DATA3+
+5V Power
Ground for 5V
Hot Plug Detect
T.M.D.S. DATA0T.M.D.S. DATA0+
T.M.D.S. DATA0/5 Shield
T.M.D.S. DATA5T.M.D.S. DATA5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
DVI-D cable does not support
analog RGB signals.
Connecting to PC
Red (R)
Green (G)
Blue (B)
Ground
Ground (DDC)
Red (R) Ground
Green (G) Ground
Blue (B) Ground
Reserved
Ground Sync
Ground
Data (DDC)
Horizontal Sync
Vertical Sync
Clock (DDC)
Connecting to PC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DVI-D
(supports only digital signals)
61
Automatic Picture Adjustment
Used to adjust frequency and phase of PC screen automatically.
Before adjusting!
Set the input mode to PC.
PC
MENU
1
Select
2, 3, 4
…/†
2, 3
EXIT
5
Connecting to PC
Automatic Picture Adjustment
62
1
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to PC, then
press the
button.
The Auto Adjustment is selected.
Setup
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Move
: Front-Floor √
: Theater
√
√
√
√
√
√
Enter
Return
PC
4
5
Press the
button.
Auto Adjustment in progress message is displayed and PC
screen is adjusted automatically.
Auto Adjustment
Coarse
Fine
Zoom
Reset
Move
Enter
Press the EXIT button to exit the menu.
Auto Adjustment in Progress..
Please Wait
√
1344
0
√
√
Return
Frequency Adjustment
Used to adjust frequency when vertical lines appear on PC screen.
Before adjusting!
Set the input mode to PC.
PC
MENU
1
Select
2, 3, 4
…/†/œ/√
2, 3, 4
EXIT
5
2
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to PC, then
press the
button.
The PC menu is displayed.
PC
4
Press the ▲ or ▼ button to move to Coarse, then
press the
button.
Press the œ or √ button to adjust.
Auto Adjustment
Coarse
Fine
Zoom
Reset
Move
5
Press the EXIT button to exit the menu.
…
Coarse
†
Enter
√
1344
0
√
√
Return
Frequency Adjustment
3
Connecting to PC
1
1344
63
Fine Tuning with the Phase Adjustment
Used to fine tune the PC screen.
Before adjusting!
Set the input mode to PC.
PC
MENU
1
Select
2, 3, 4
…/†/œ/√
2, 3, 4
EXIT
5
Connecting to PC
Fine Tuning with the Phase Adjustment
64
1
2
3
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to PC, then
press the
button.
The PC menu is displayed.
PC
4
Press the ▲ or ▼ button to move to Fine, then
press the
button.
Press the œ or √ button to adjust.
Auto Adjustment
Coarse
Fine
Zoom
Reset
Move
5
Press the EXIT button to exit the menu.
…
Fine
†
Enter
√
1344
0
√
√
Return
0
Zooming the Screen
Used to extend PC screen from the center.
Before adjusting!
Set the input mode to PC.
PC
MENU
1
Select
2, 3, 4, 5
…/†/œ/√
2, 3, 4, 5
EXIT
6
2
4
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to PC, then
press the
button.
The PC menu is displayed.
PC
Auto Adjustment
Coarse
Fine
Zoom
Reset
Press the ▲ or ▼ button to move to Zoom, then
press the
button.
Move
5
Enter
√
1344
0
√
√
Return
Zooming the Screen
3
Connecting to PC
1
Press the ▲, ▼, œ, or √ button to move to
desired position, then press the
button to
extend as you want.
The screen can be extended by 1, 2, 4, or 8 times.
x2
6
Move
Zoom
Return
Press the EXIT button to exit the menu.
65
Reset the PC
Used to reset PC mode settings to the Factory Default values.
Before adjusting!
Set the input mode to PC.
PC
MENU
1
Select
2, 3, 4, 5
…/†/œ/√
2, 3, 4, 5
EXIT
6
Connecting to PC
1
2
Reset the PC
3
4
Press the MENU button.
The main menu is displayed.
Press the ▲ or ▼ button to move to Setup.
The Setup menu is displayed.
Press the
button.
Press the ▲ or ▼ button to move to PC, then
press the
button.
The PC menu is displayed.
Press the ▲ or ▼ button to move to Reset, then
press the
button.
PC
Move
5
Press the œ or √ button to move to OK, then
press the
button.
The PC is reset to the time of purchasing.
66
Press the EXIT button to exit the menu.
Enter
Return
Reset
Back to Default Settings?
Cancel
OK
Move
6
√
1344
0
√
√
Auto Adjustment
Coarse
Fine
Zoom
Reset
Enter
Return
V
I
S
U
A
L
R
E
A
L
I
S
M
Before Contacting Service Personnel........68
Connecting to PC
Troubleshooting
Reset the PC
67
Before Contacting Service Personnel
If this projector does not operate properly, check the following first.
If the problem is continues, contact your dealer.
Installation and Connection
Symptoms
Troubleshooting
Troubleshooting
Note
No Power.
Be sure that the power cord in place and the power switch
on the rear side of the projector is turned on "-".
Page 15
Image is distorted or
trapezoidal.
Be sure to make the projection beam perpendicular to the
screen and adjust the focus using the Zoom Knob and the
Focus Ring. Avoid to use the V-Keystone function if possible.
Pages
16~20
Want to install
projector on ceiling.
Ceiling bracket is an optional accessory.
Please contact your dealer.
Image is distorted or
trapezoidal.
Be sure that the connection cable (video) is properly
connected to the proper port. Unless they are connected
properly, the device is not available.
Menu and Remote Control
Symptoms
Before Contacting Service Personnel
68
Pages
23~25
Remote control does
not work.
Some of Menu functions
do not work.
Troubleshooting
Note
■
Be sure that the proper external source is selected.
Page 26
■
Check batteries of the remote control. If there is a
problem, replace them with recommended ones.
Page 12
■
Check the angle and distance between the remote control
and the projector. Be sure that there is no obstacle
between the projector and the remote control that may
block the signal.
Page 13
■
Direct lighting of 3-way light bulbs or other lighting
device on the remote sensor of the projector may affect the
sensitivity and cause the remote control to malfunction.
Refer to the user manual. Some functions are locked
depending on sources and type of the input signal.
Pages
23~26
Screen and External Source
Symptoms
Cannot see picture
images.
Troubleshooting
■
■
■
■
■
Be sure that the power cord of the projector is in place.
Be sure that the proper input source is selected.
Be sure that cable is properly connected to the rear panel
of the projector.
Check the Remote Control batteries.
Be sure that the Color, Brightness settings are not at their
lower limit.
Note
Page 15
Page 26
Pages
23~25
Page 12
Page 31
Adjust the Color and Brightness.
Page 31
Images are not clear.
■
Page 16
Page
19~20
■
Adjust the focus.
Check that the projection distance is either too far or too
near to the screen.
Contact your service personnel if the noise continues due
to defective parts.
Repair indicator is on.
Refer to instructions on lamp and repair.
Page 9
Lines appear on screen.
Noisy lines may appear for PC mode in case of frequency
discrepancy. Adjust the vertical frequency of your video
card on the advanced display property.
Page 63
Green appears on the
screen.
Be sure to properly connect the external devices.
Especially, connect the component (Y, Pb, Pr) cables
matching the color codes.
Pages
23~25
Cannot see the picture
from the external
devices.
Be sure that the proper operation of the external device.
Adjustable items of the Custom Picture Menu are properly
set.
Pages
26, 31
Only blue screen
appears.
Be sure to properly connect the external devices.
Check the connection cables again.
Pages
26,
23~25
■
Page 31
Screen appears in
black and white or
odd color/screen is too
dark or bright.
■
Adjustable items of the Custom Picture Menu are
properly set.
Execute Factory Default if you want to restore the factory
default setting values.
Before Contacting Service Personnel
Strange noise.
Troubleshooting
Poor color.
Page 48
69
V
I
S
U
A
L
R
E
A
L
I
S
M
Other Information
Storage and Maintenance ..........................72
Purchasing Optional Parts ........................73
Structure of Screen Menu ..........................74
Lamp Replacement ......................................77
RS-232C Connection and Control ..............78
Specifications ..............................................80
Remote Control Specifications ..................81
Storage and Maintenance
Clean and maintain the projector in the following way.
Cleaning the Projector and Lens
Use a dry soft cloth.
■
Do not use flammable materials such as benzene and
thinner. Do not use a wet cloth. It may result in
malfunction.
■
Do not clean the lens using a fingertip or a sharp object.
It may leave scratches.
Other Information
Cleaning the Inside of the Projector
Contact your dealer or service personnel to clean
the inside of the projector.
Contact your dealer if particles or other objects are stuck
inside of the projector.
Storage and Maintenance
72
Purchasing Optional Parts
Information for purchasing accessories or optional parts.
Optional Parts
DVI-D Cable
You can purchase at electronics shops or over the Internet.
Video (Composite) Cable
S-Video Cable
Component Cable
Other Information
1.5V AAA Batteries
PC Video Cable
You can purchase at electronics shops or over the Internet.
Or you can call your dealer or service center.
Purchasing Optional Parts
73
Structure of Screen Menu
You can see the entire structure of screen menu.
Buttons used for Screen Menu
Open Menu/Exit Menu
Select an item/change setting value
Select Composite/S-Video/Component Input Mode
Input
: Component1 √
√
Source List
Edit Name
Move
Enter
Return
Input
Other Information
Source List
Component1 / Component2 / S-Video / Composite / PC / DVI
Edit Name
Component1 / Component2 / S-Video / Composite / PC / DVI (Selected without Input)
VCR / DVD / Cable / Satellite / AV Receiver / DVD Receiver / Game
Camcorder / Combo / PC
Picture
Picture Mode
Custom Picture
Picture Size
DNIe
Film Mode
Overscan
Move
Enter
: Movie1
: Full
: Off
: On
: On
√
√
√
√
√
√
Return
Picture
Structure of Screen Menu
74
Picture Mode
Custom Picture
Dynamic / Standard / Movie1 / Movie2 /
User1 / User2 / User3 / Custom
Contrast
0 ~ 100
Brightness
0 ~ 100
Sharpness
0 ~ 100
Color
0 ~ 100
Tint
0 ~ 100 (Not supported in 480p mode or above)
Color Standard
SMPTE_C/HD/EBU
Color Temperature
5500K / 6500K / 8000K / 9300K
Gamma
Gamma Mode1 / Gamma Mode2 / Gamma Mode3
Save
User1 / User2 / User3
Picture Size
Full / Zoom1 / Zoom2 / 4:3
Position
DNIe
Off / Demo / On
Film Mode
Off / On
Overscan
Off / On
Setup
Install
Light Setting
V-Keystone
Test Pattern
PC
Factory Default
Information
Move
: Front-Floor
: Theater
Enter
√
√
√
√
√
√
√
Return
Setup
Light Setting
Front-Floor / Front-Ceiling / Rear-Floor / Rear-Ceiling
Theater
Bright
V-Keystone
Test Pattern
-50 ~ 50
Crosshatch
Other Information
Install
Screen Size
Color Standard
Structure of Screen Menu
Red
Green
Blue
White
6500K_White
PC
Auto Adjustment
Coarse
Fine
Zoom
Reset
Factory Default
Information
OK / Cancel
OK / Cancel
75
Structure of Screen Menu (Continued)
Menu Option
Language
: English
Menu Position
Menu Translucency : Opaque
Menu Display Time : 120 Sec
Move
Enter
√
√
√
√
Return
Menu Option
Language
English / Deutsch / Nederlands / Español / Français /
Italiano / Svenska / Português /
/
Menu Position
Other Information
Structure of Screen Menu
76
Menu Translucency
Opaque / High / Medium / Low
Menu Display Time
5 / 10 / 30 / 60 / 90 / 120 / Stay On
Lamp Replacement
Cautions on Lamp Replacement
Projector lamp requires replacement after.
■
Use the recommended lamp when replacing. Lamp specifications are defined in the user’s
manual. Replace with the same model provided with the projector.
- Lamp Model Name : LAMP-MERCURY-Philips
- Lamp Manufacture : Philips Lighting
- Lamp Life Time
: 2000Hrs
- Lamp Type
: 250W UHP
- Lamp Part Number : BP47-00010A
■
Check that the power cord is unplugged before replacing lamps.
■
Wait for at least 30 minutes before replacing lamps to cool off the lamp unit after
disconnecting power.
■
Lamp is a high-pressure product. Do not place near flammable materials or children.
■
Remove dirts or foreign materials around or inside the lamp unit using a proper vacuum
device.
■
Be careful not to touch the lamp itself when handling the lamp unit.
■
If the lamp is poorly handled, it may result in poor picture quality or shorter life time of
lamp.
■
The projector is will not operate normally if the cover is not locked completely after lamp
replacement. Refer to LED information in the user’s manual if the projector does not operate
normally.
Lamp Replacement Procedure
2 Push to open the lamp
4 Lift and grip the lamp
5 Reverse the disassembly
lamp cover.
handle in the direction of
the arrow and pull it out.
cover in the direction of
the arrow.
procedure to assemble the
unit after replacement.
3 Detach the three screws.
Lamp Replacement
1 Detach the screw of the
Other Information
■
■
NOTE
■
The Lamp is hightemperature highpressure product.
Wait for at least 30
minutes to proceed after
disconnecting power.
Be sure that the power
cord is disconnected
before proceeding.
77
RS-232C Connection and Control
Connecting the Projector to a PC
You can connect the Projector to a PC using the RS232C (Crossed, Female Type) cable to control the
projector.
■ Do not disconnect or connect the RS-232C cable
while the Computer or the Projector is operating. It
may cause serious damage to the Computer or the
Projector.
■ If the PC is not properly configured, the RS-232C
connection may not work properly. For further
details, refer to the Computer’s product
documentation.
Communication Format (Complies with the RS232C Standard)
■
Transmission Speed: 115,200 bps
■
Parity Bit: No
■
Data Length: 8 data bits, 1 stop bit
Other Information
Transmission Sequence and Data Format
Transmission Sequence
Argument 1 → Argument 2 → -----
CN
0x12
CC
CS
RS-232C Connection and Control
Argument N, Command, Response
CN : Command + Number of Variables
(Hexadecimal)
Structure for Variables (8 bytes)
CC : Command - Hexadecimal
(Refer to the commands table)
0x08
0x11
N
PN
CS
N : Variable’s Number (Hexadecimal)
PN : Value of the Variable
(Implemented in 4 bytes - Hexadecimal)
CS : Checksum
(Boolean complementation of the
summation of all bytes except the CS)
CS : Checksum
(Boolean complementation of the
summation of all bytes except the CS)
Command Structure (4 bytes)
- Confirms proper data transmission
CN
0x12
CC
CS
- No response for communication errors or
invalid commands
■
■
78
Command Structure (4 bytes)
■
Transmit the following control command to transmit one or more control commands if there was a successful
response for the previous transmission or there was no response in over 3 seconds.
While controlling the Projector using a Computer, you cannot check the Projector’s status change using the
Computer nor will it be displayed on the Projector’s screen. Transmit the INFORMATION command to display
the current information on the Projector’s screen.
All the control commands apply to the input source and the Projector’s status currently displayed.
Commands
e.g.) DISPLAY → CUSTOM CONFIGURATION → Set the CONTRAST to 60
Prameter 1
0x08
0x11 0x01 0x00
0x00
0x00
0x01 0xE5
Prameter 2
0x08
0x11 0x02 0x00
0x00
0x00
0x03 0xE2
Prameter 3
Command
0x08
0x11 0x03 0x00
0x00
0x00 0x3C 0xA8
0x04
0x12 0x4B 0x9F
Return
0x03 0x0C 0xF1
Control Items
General
Input
Power
Input
Check
Picture Mode
Custom Picture
Command
Parmeters
On
76
0,5
Off
76
0,3
Direct Off
76
0,6
Component1
76
Return
Control Items
Picture
76
2,9
S-Video
76
2,11
Setup
Parmeters
75
2,11,1
On
Off
75
2,11,0
Overscan
On
75
2,12,1
Off
75
2,12,1
2,8
Component2
Command
Film Mode
Install
Front-Floor
75
0,1,0
Front-Ceiling
75
0,1,1
Composite
76
2,10
Rear-Floor
75
0,1,2
PC
DVI
76
76
2,12
2,7
Rear-Ceiling
75
0,1,3
Component1
77
64,208
1 or 0
Component2
77
64,209
1 or 0
Light Setting
Theater
76
0,2,1
Bright
76
0,2,0
Test Pattern
Crosshatch
76
0,0,1
S-Video
77
64,210
1 or 0
Color Standard
76
0,0,2
Composite
PC
77
77
64,211
64,212
1 or 0
1 or 0
Red
76
0,0,3
Green
1 or 0
76
0,0,4
DVI
77
64,213
Blue
76
0,0,5
Dynamic
75
2,10,0
White
76
0,0,6
Standard
75
2,10,1
6500K_White
76
0,0,7
Movie1
75
2,10,2
V-Keystone
V-Keystone (-50~50)
75
0,3,x
Movie2
75
2,10,3
PC
Auto Adjustment
76
6,5
User1
75
2,10,4
Coarse (0~2000)
76
User2
75
2,10,5
Fine (0~255)
76
6,4,x
User3
75
2,10,6
Zoom (0~3)
76
6,13,x
Custom
75
2,10,7
PC Reset
76
6,14
Contrast (0~100)
75
1,3,x
Confirm
76
Factory Default
6,3,x
9
Information
OK
76
0,2,0
Language
English
76
10,0,0
1,6,x
Deutsch
76
10,0,1
1,7,x
Nederlands
76
10,0,2
1,1,0
Español
76
10,0,3
Brightness (0~100)
75
1,4,x
Sharpness (0~100)
75
1,5,x
Color (0~100)
75
Tint (0~100)
75
Color Standard
SMPTE-C
76
HD
76
1,1,1
EBU
76
1,1,2
Italiano
76
10,0,5
Color Temperature
5500K
75
2,0,3
Svenska
76
10,0,6
6500K
75
2,0,2
Português
8000K
75
2,0,1
Menu Option
Français
76
10,0,7
10,0,8
9300K
75
2,0,0
75
2,3,x
Up
76
76
10,0,9
10,1,0
75
2,4,x
Down
76
10,1,1
B(0~100)
75
2,5,x
Left
76
10,1,2
Offset
R(-50~50)
75
2,6,x
Right
76
10,1,3
2,7,x
Opaque
76
10,2,0
B(-50~50)
75
2,8,x
High
76
10,2,2
Gamma
Gamma Mode1
75
2,1,0
Medium
76
10,2,4
Gamma Mode2
75
2,1,1
Low
76
10,2,6
G(-50~50)
Picture Size
Position
DNIe
75
Menu Translucency
Gamma Mode3
75
2,1,2
Stay On
76
10,3,6
Full
75
2,9,0
5
76
10,3,0
Zoom1
75
2,9,2
10
76
10,3,1
Zoom2
75
2,9,3
30
76
10,3,2
4:3
75
2,9,4
60
76
10,3,3
Up
75
2,13,0
90
76
10,3,4
Down
75
2,13,1
120
76
10,3,5
Left
75
2,13,2
EXIT
76
0,4
Right
75
2,13,3
On
76
0,1,1
Off
76
0,1,0
Demo
76
0,1,2
Menu Display Time
Menu
RS-232C Connection and Control
76
76
R(0~100)
Menu Position
10,0,4
G(0~100)
Gain
Return
Other Information
Picture
: Range is –50 ~ 50, use the Boolean Complementary for
negative values.
79
Specifications
Design and specifications of the product may be modified without prior notice for better performance.
This appliance is Class B device that can be used in both residential and industrial areas.
Model
Classification
Panel
SP-H500
Size
0.8"(HD2+)
0.63"(ED2)
Resolution
1280 x 720
1024 x 576
Type
250W UHP
Life Time
2000Hrs
Power Consumption
350W
Voltage
AC 100-240V
Frequency
50/60Hz
Lamp
Power
SP-H700/H710
Dimensions
384 x 425 x 177 mm / 15.1" x 16.7" x 7.0"
Weight
9.0 kg / 19.8 lb
Owner's Instructions, Power Cord, Remote control, Batteries
Accessories
Key Features
Brightness
700 ANSI
600 ANSI
Contrast (Theatre Mode)
2800 : 1
2000 : 1
Screen Size
Diagonal 30.385~300"
Other Information
Projection Range
1.0 ~ 13.6 m / 3.4 ~ 44.8 ft
Keystone
Input/Output
DVI
Diagonal 40~200"
1.3 ~ 8.8 m / 4.4 ~ 28.5 ft
Vertical
1) Connector Type: DVI-D
2) Available Format: PC - VGA~SXGA
DTV - 480p, 576p, 720p, 1080i
3) Frequency: Refer to page 63.
PC
1) Connector Type: 15Pin D-Sub
2) Frequency: Refer to page 63.
Specifications
Component 1
1) Signal Type: Y, Pb, Pr
Component 2
2) Available Format: 480i, 480p, 576i, 576p, 720p, 1080i
3) Frequency: Refer to page 63.
S-Video
Signal Format: NTSC, PAL, SECAM
Composite
RS-232C
User Environment
Temperature and
Humidity
80
Service Port
Operating Temperature (32~104ºF / 0~40ºC), Humidity (10~80%)
Storage
Temperature (-4~113ºF / -20~45ºC), Humidity (5~95%)
Device Classification
Class B
Noise
Min 28dB (Theater Mode)
The DMD Panel used in DLP Projectors consists of several hundred thousand micro mirrors.
As with other visual display elements, the DMD Panel may include a few bad pixels. Samsung
and the DMD Panel manufacturer have a rigid, bad pixel identification and limitation
procedure in place and products will not exceed the maximum number of bad pixels set by
our standards. Rarely, non-displayable pixels may exist, however it does not affect the overall
picture quality nor the lifespan of the product.
Remote Control Specifications
Function and Transmission Codes
Other Information
LEADER
4.5msec
PULSE
4.5msec
System Code
System Code
Data Code
/Data Code
(Reverse Data Code)
07h
07h
Data
/Data
(Reverse Data)
Remote Control Specifications
Remote Control Signal Format
81
Memo
82
Memo
83
Europe Only
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
BP68-00507C-00