Mitsubishi Electric MXZ-8C48NA Installation manual

Split-type Air-Conditioner
MXZ-3B54VA
MXZ-4B71VA
INSTALLATION MANUAL
English
• Refer to the installation manual of each indoor unit for indoor
unit installation.
IMPORTANT NOTES
TO COMPLY WITH THE REQUIREMENTS OF AUSTRALIAN STANDARD
AS/NZS 3000 ELECTRICAL INSTALLATIONS (Wiring Rules),
THE ELECTRICAL WIRING REQUIRED BETWEEN THE INDOOR AND
OUTDOOR UNITS MUST BE INSTALLED BY A LICENCED ELECTRICAL
CONTRACTOR.
CONTENTS
1. BEFORE INSTALLATION...............................................................................2
2. OUTDOOR UNIT INSTALLATION..................................................................5
3. FLARING WORK AND PIPE CONNECTION..................................................5
4. PURGING PROCEDURES, LEAK TEST, AND TEST RUN............................6
5. RELOCATION AND MAINTENANCE.............................................................7
FOR INSTALLER
MXZ-3B_4BVA-A1 JG79A319H01.indd
1
2009/10/13
10:26:47
1. BEFORE INSTALLATION
1-1.THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY
• Be sure to read “THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY” before installing the air conditioner.
• Be sure to observe the warnings and cautions specified here as they include important items related to safety.
• After reading this manual, be sure to keep it together with the OPERATING INSTRUCTIONS for future reference.
WARNING
(Could lead to death, serious injury, etc.)
n Do not install the unit by yourself (user).
Incomplete installation could cause fire or electric shock, injury due to the
unit falling, or leakage of water. Consult the dealer from whom you purchased the unit or a qualified installer.
n Perform the installation securely referring to the installation manual.
Incomplete installation could cause fire or electric shock, injury due to the
unit falling, or leakage of water.
n Install the unit securely in a place which can bear the weight of the
unit.
If the installation location cannot bear the weight of the unit, the unit
could fall causing injury.
n Perform electrical work according to the installation manual and be
sure to use an exclusive circuit. Do not connect other electrical appliances to the circuit.
If the capacity of the power circuit is insufficient or there is incomplete
electrical work, it could result in a fire or an electric shock.
n Do not damage the wires by applying excessive pressure with parts
or screws.
Damaged wires could cause fire.
n Be sure to cut off the main power in case of setting up the indoor P.C.
board or wiring works.
Failure to do so could cause electric shock.
n Use the specified wires to connect the indoor and outdoor units securely and attach the wires firmly to the terminal block connecting
sections so the stress of the wires is not applied to the sections.
Incomplete connecting and securing could cause fire.
n Do not install the unit in a place where inflammable gas may leak.
If gas leaks and accumulates in the area around the unit, it could cause
an explosion.
n Do not use intermediate connection of the power cord or the extension cord and do not connect many devices to one AC outlet.
It could cause a fire or an electric shock due to defective contact, defective insulation, exceeding the permissible current, etc.
n Be sure to use the parts provided or specified parts for the installation work.
The use of defective parts could cause an injury or leakage of water due
to a fire, an electric shock, the unit falling, etc.
n When plugging the power supply plug into the outlet, make sure
that there is no dust, clogging, or loose parts in both the outlet and
the plug. Make sure that the power supply plug is pushed completely into the outlet.
If there is dust, clogging, or loose parts on the power supply plug or the
outlet, it could cause electric shock or fire. If loose parts are found on the
power supply plug, replace it.
CAUTION
n Attach the electrical cover to the indoor unit and the service panel
to the outdoor unit securely.
If the electrical cover of the indoor unit and/or the service panel of the
outdoor unit are not attached securely, it could result in a fire or an
electric shock due to dust, water, etc.
n When installing or relocating the unit, make sure that no substance other than the specified refrigerant (R410A) enters the
refrigerant circuit.
Any presence of foreign substance such as air can cause abnormal
pressure rise or an explosion.
n Do not discharge the refrigerant into the atmosphere. If refrigerant
leaks during installation, ventilate the room.
If refrigerant comes in contact with a fire, harmful gas could be generated.
n Check that the refrigerant gas does not leak after installation has
been completed.
If refrigerant gas leaks indoors, and comes into contact with the flame
of a fan heater, space heater, stove, etc., harmful substances will be
generated.
n Use appropriate tools and piping materials for installation.
The pressure of R410A is 1.6 times more than R22. Not using appropriate tools or materials and incomplete installation could cause the pipes
to burst or injury.
n When pumping down the refrigerant, stop the compressor before
disconnecting the refrigerant pipes.
If the refrigerant pipes are disconnected while the compressor is running and the stop valve is open, air could be drawn in and the pressure
in the refrigeration cycle could become abnormally high. This could
cause the pipes to burst or injury.
n When installing the unit, securely connect the refrigerant pipes
before starting the compressor.
If the compressor is started before the refrigerant pipes are connected
and when the stop valve is open, air could be drawn in and the pressure in the refrigeration cycle could become abnormally high. This
could cause the pipes to burst or injury.
n Fasten a flare nut with a torque wrench as specified in this
manual.
If fastened too tight, a flare nut may break after a long period and cause
refrigerant leakage.
n The unit shall be installed in accordance with national wiring regulations.
n Earth the unit correctly.
Do not connect the earth to a gas pipe, water pipe, lightning rod or telephone earth. Defective earthing could cause electric shock.
(Could lead to serious injury in particular environments when operated incorrectly.)
nInstall an earth leakage breaker depending on the installation place.
If an earth leakage breaker is not installed, it could cause electric shock.
n Perform the drainage/piping work securely according to the installation manual.
If there is defect in the drainage/piping work, water could drop from the
unit, soaking and damaging household goods.
1-2.REQUIRED TOOLS FOR INSTALLATION
Phillips screwdriver
Level
Scale
Utility knife or scissors
Torque wrench
Wrench (or spanner)
4 mm hexagonal wrench
Flare tool for R410A
n Do not touch the air inlet or the aluminum fins of the outdoor
unit.
This could cause injury.
n Do not install the outdoor unit where small animals may live.
If small animals enter and touch the electric parts inside the unit, it
could cause a malfunction, smoke emission, or fire. Also, advise user
to keep the area around the unit clean.
Gauge manifold for R410A
Vacuum pump for R410A
Charge hose for R410A
Pipe cutter with reamer
1-3.SPECIFICATIONS
Pipe length and height difference *4, *5, *6, *10
Max. no. of bends
Max. pipe length
Rated
Fre- Breaker
Refrigerant adjustIndoor/outdoor
Max. per indoor unit /
Power supply
per indoor unit /
Voltage quency capacity
height difference
ment A *7
connecting wire
for multi system
for multi-system
25
m
/
50
m
25
/
50
4-core
230 V 50 Hz
25 A 3-core 2.5 mm2
15 m
20 g/m
1.0/1.5 mm2
25 m / 60 m
25 / 60
Power supply *1
Model
MXZ-3B54VA
MXZ-4B71VA
Wire specifications *2
*1Connect to the power switch which has a gap of 3 mm or more when open
to interrupt the source power phase. (When the power switch is shut off, it
must interrupt all phases.)
*2Use wires in conformity with design 60245 IEC 57. Use the indoor/outdoor
connecting wire in conformity with the wire specifications specified in the
installation manual of the indoor unit.
*3Never use pipes with thickness less than specified. The pressure resistance will be insufficient.
*4Use a copper pipe or a copper-alloy seamless pipe.
*5Be careful not to crush or bend the pipe during pipe bending.
*6Refrigerant pipe bending radius must be 100 mm or more.
*7If pipe length exceeds 40 m, additional refrigerant (R410A) charge is required. (No additional charge is required for pipe length less than 40 m.)
Additional refrigerant = A × (pipe length (m) - 40)
*8Insulation material : Heat resisting foam plastic 0.045 specific gravity
*9Be sure to use the insulation of specified thickness. Excessive thickness
may cause incorrect installation of the indoor unit and insufficient thickness may cause dew drippage.
*10If the outdoor unit is installed higher than the indoor unit, max. height
difference is reduced to 10 m.
MXZ-3B_4BVA-A1 JG79A319H01.indd
2
2009/10/13
10:26:49
1-4.SELECTING PIPE SIZE AND OPTIONAL DIFFERENT-DIAMETER JOINTS
The diameter of connection pipes differs according to the type and capacity of indoor units. Match the diameters of connection pipes for indoor and outdoor
units according to the following table.
• If the diameter of connection pipes does not match the diameter of pipe end connections, use optional different-diameter joints.
(Unit: mm)
22/25/35
Indoor unit
50
60
6.35 (0.8) / 9.52 (0.8)
6.35 (0.8) / 12.7 (1.0)
6.35 (0.8) / 15.88 (1.0)
- / MAC-A455JP
-/-
- / MAC-A456JP
-/-
- / MAC-454JP
- / PAC-SG76RJ
Outdoor unit
MXZ3B54VA
A UNIT
B UNIT
C UNIT
Pipe size
MXZ4B71VA Liquid (Wall thickness) / Gas (Wall thickness)
A UNIT
6.35 (0.8) / 12.7 (1.0)
B UNIT
C UNIT
6.35 (0.8) / 9.52 (0.8)
D UNIT
1-5.SELECTING THE INSTALLATION LOCATION
•
•
•
•
•
Where it is not exposed to strong wind.
Where airflow is good and dustless.
Where rain or direct sunshine can be avoided as much as possible.
Where neighbours are not annoyed by operation sound or hot air.
Where rigid wall or support is available to prevent the increase of operation sound or vibration.
• Where there is no risk of combustible gas leakage.
• When installing the unit at a high level, be sure to secure the unit legs.
• Where it is at least 3 m away from the antenna of TV set or radio. Operation of the air conditioner may interfere with radio or TV reception in
areas where reception is weak. An amplifier may be required for the affected device.
• Install the unit horizontally.
• Please install it in an area not affected by snowfall or blowing snow.
In areas with heavy snow, please install a canopy, a pedestal and/or
some baffle boards.
Note:
It is advisable to make a piping loop near outdoor unit so as to reduce
vibration transmitted from there.
FREE SPACE REQUIRED AROUND OUTDOOR UNIT
1.Top side obstacles
When there is an obstacle behind the
rear side only, it does not matter if
there is an obstacle over the top side
as shown in the figure below.
100 or more
500 or more
Note:
When operating the air conditioner in low outside temperature, be sure
to follow the instructions described below.
• Never install the outdoor unit in a place where its air inlet/outlet side
may be exposed directly to wind.
• To prevent exposure to wind, install the outdoor unit with its air inlet
side facing the wall.
• To prevent exposure to wind, it is recommended to install a baffle
board on the air outlet side of the outdoor unit.
Avoid the following places for installation where air conditioner trouble
is liable to occur.
• Where flammable gas could leak.
• Where there is much machine oil.
• Salty places such as the seaside.
• Where sulfide gas is generated such as a hot spring.
• Where there is high-frequency or wireless equipment.
2.Front (blowing) side open
As long as space like the one
shown in the figure can be
maintained, it does not matter if there are obstacles in
three directions (but top side
is open).
200 or more
350 or more
100 or more
3.Obstacles on front (blowing) side only
4.Obstacles on front and rear side only
In this case, the rear, both sides and
top should be open.
500 or more
The unit can be used by attaching an optional outdoor
blowing guide (MAC-889SG)
(but both sides and top are
open).
100 or more
500 or more
Blowing guide (MAC-889SG)
5.Service space
Keep the service space as shown in the figure below for maintenance.
Service space
100 or more
500 or more
• When installing the unit in an area that is enclosed on four sides such
as a verandah, be sure to leave move than 200 mm behind the unit as
shown.
• When there is a lack of airflow or there is a possibility of becoming
short cycle, install an outlet guide and make sure there is enough
space behind the rear side of the air inlet.
Note:
Make sure not to install several outdoor units sideways next to each
other.
Window
100 or more
500 or more
350 or more
More than 200
More than
100
More than 200
Less than 1,200 of the front surface side
More than
350
More than 200
(Unit: mm)
MXZ-3B_4BVA-A1 JG79A319H01.indd
3
2009/10/13
10:26:51
1-6.INSTALLATION DIAGRAM
ACCESSORIES
Check the following parts before installation.
After the leak test, apply insulating material tightly so that there is
no gap.
When the piping is to be attached to a wall containing metals
(tin plated) or metal netting, use
a chemically treated wooden
piece 20 mm or thicker between
the wall and the piping or wrap 7
to 8 turns of insulation vinyl tape
around the piping.
To use existing piping, perform
COOL operation for 30 minutes
and pump down before removing
the old air conditioner. Remake
flare according to the dimension
for new refrigerant.
Open as a rule
More than 500 mm
if the front and both
sides are open
MXZ-4B71VA
More than 100 mm More than 200 mm if there are obstacles to
both sides
More than
100 mm
(1) Drain socket
(2) Drain cap
1
2
PARTS TO BE PROVIDED AT YOUR SITE
(A)
(B)
(C)
(D)
(E)
Power supply cord*
Indoor/outdoor unit connecting wire*
Extension pipe (Refer to 1-4.)
Wall hole cover
Piping tape
Extension drain hose
(F) (or soft PVC hose, 15 mm inner
diameter or hard PVC pipe VP16)
(G) Refrigeration oil
(H)
(I)
(J)
(K)
Putty
Pipe fixing band
Fixing screw for (I)
Wall hole sleeve
Soft PVC hose, 15 mm inner di(L) ameter or hard PVC pipe VP16 for
drain socket
1
1
1
1
1
1
Little
amount
1
2 to 7
2 to 7
1
1
* Note:
Place indoor/outdoor unit connecting wire (B) and
power supply cord (A) at least 1 m away from the
TV antenna wire.
The “Q’ty” for (B) to (K) in the above table is quantity to be used per indoor unit.
Open as a rule
More than 500 mm if the back,
both sides and top are open
More than 350 mm
Units should be installed by licensed contractor according to local code requirements.
Outdoor unit installation
835
166
500
Air inlet
396
361
330
Air inlet
Air outlet
4-10 × 21 Oval holes
(Unit: mm)
1-7.MOUNTING ARRANGEMENT OF DRAIN SOCKET
Please perform the drain piping work only when draining from one place.
1)Choose one hole to discharge drain and install the drain socket to the hole.
2)Close the rest of the holes with the drain caps.
3)Connect a vinyl hose of 15 mm in the inside diameter on the market with the drain socket and lead drain.
Note:
Install the unit horizontally.
Do not use the drain socket in the cold regions. Drain may freeze and it makes the fan stop.
The outdoor unit produces condensate during the heating operation. Select the installation place to ensure to prevent the outdoor unit and/or the grounds
from being wet by drain water or damaged by frozen drain water.
MXZ-3B_4BVA-A1 JG79A319H01.indd
4
2009/10/13
10:26:53
2. OUTDOOR UNIT INSTALLATION
Terminal block for power supply
2-1.CONNECTING WIRES FOR OUTDOOR UNIT
1)Remove the service panel.
2)Loosen terminal screw, and connect indoor/outdoor unit connecting
wire (B) from the indoor unit correctly on the terminal block. Be careful
not to make mis-wiring. Fix the wire to the terminal block securely so
that no part of its core is appeared, and no external force is conveyed
to the connecting section of the terminal block.
3)Firmly tighten the terminal screws to prevent them from loosening. After tightening, pull the wires lightly to confirm that they do not move.
4) Perform 2) and 3) for each indoor unit.
5)Connect power supply cord (A).
6)Fix indoor/outdoor unit connecting wire (B) and power supply cord (A)
with the cable clamps.
7)Close the service panel securely. Make sure that 3-2. PIPE CONNECTION is completed.
• After making connections between both power supply cord (A) and
indoor/outdoor unit connecting wire (B), be sure to fix both cable and
wire with cable clamps.
4B71VA
D unit is for 4B71VA only
Service panel
Indoor/outdoor unit connecting wire
Terminal
block
<OUTDOOR UNIT>
Terminal
block
Terminal
block
Terminal block for
power supply
Terminal
block
15 mm
35 mm
Lead wire
UNIT
UNIT
UNIT
UNIT
UNIT
UNIT
*
UNIT
*D unit is for 4B71VA only
POWER SUPPLY
~/N 230 V 50 Hz
UNIT
<INDOOR UNIT>
• Be sure to attach each screw to its correspondent terminal when securing the cord and/or the wire to the terminal block.
• Make earth wire a little longer than others. (More than 35 mm)
• For future servicing, give extra length to the connecting wires.
3. FLARING WORK AND PIPE CONNECTION
3-1.FLARING WORK
1)Cut the copper pipe correctly with pipe cutter. (Fig. 1, 2)
2)Completely remove all burrs from the cut cross section of pipe. (Fig. 3)
• Put the end of the copper pipe to downward direction as you
remove burrs in order to avoid to let burrs drop in the piping.
3)Remove flare nuts attached to indoor and outdoor units, then put them
on pipe having completed burr removal. (Not possible to put them on
after flaring work.)
4)Flaring work (Fig. 4, 5). Firmly hold copper pipe in the dimension
shown in the table. Select A mm from the table according to the tool
you use.
5)Check
• Compare the flared work with Fig. 6.
• If flare is noted to be defective, cut off the flared section and do
flaring work again.
A (mm)
Pipe diameter Nut
Clutch
Clutch Wing nut
(mm) type tool type tool type tool [mm (in.)]
for R410A for R22
for R22
ø6.35 (1/4”) 17
1.5 to 2.0
ø9.52 (3/8”) 22
0 to 0.5 1.0 to 1.5
2.0 to 2.5
ø12.7 (1/2”) 26
ø15.88 (5/8”) 29
Tilted Uneven Burred
Fig. 1
kgf•cm
13.7 to 17.7
34.3 to 41.2
49.0 to 56.4
73.5 to 78.4
140 to 180
350 to 420
500 to 575
750 to 800
Fig. 2
Flaring tool
Burr
Copper pipe
Spare reamer
Pipe cutter
Tightening torque
N•m
No good
Good
Copper
pipe
Clutch type
Fig. 3
Fig. 4
Smooth all
around
Die
Flare nut
Wing nut type
Inside is shining without any
scratches.
Copper pipe
Even length
all around
Fig. 5
Fig. 6
MXZ-3B_4BVA-A1 JG79A319H01.indd
5
2009/10/13
10:26:59
3-2.PIPE CONNECTION
• Fasten flare nut with a torque wrench as specified in the table.
• When fastened too tight, flare nut may brake after a long period and
cause refrigerant leakage.
Outdoor unit connection
Connect pipes to stop valve pipe joint of the outdoor unit in the same
manner applied for indoor unit.
• For tightening, use a torque wrench or spanner and use the same
tightening torque applied for indoor unit.
WARNING
When installing the unit, securely
connect the refrigerant pipes before
starting the compressor.
3-3.INSULATION AND TAPING
1)Cover piping joints with pipe cover.
2)For outdoor unit side, surely insulate every piping including valves.
3)Using piping tape (E), apply taping starting from the entry of outdoor
unit.
• Stop the end of piping tape (E) with tape (with adhesive agent attached).
• When piping have to be arranged through above ceiling, closet or
where the temperature and humidity are high, wind additional commercially sold insulation to prevent condensation.
4. PURGING PROCEDURES, LEAK TEST, AND TEST RUN
4-1.PURGING PROCEDURES AND LEAK TEST
1)Remove service port cap of stop valve on the side of the outdoor unit
gas pipe. (The stop valve will not work in its initial state fresh out of
the factory, totally closed with cap on.)
2)Connect gauge manifold valve and vacuum pump to service port of
stop valve on the gas pipe side of the outdoor unit.
3)Run the vacuum pump. (Vacuumize for more than 15 minutes.)
4)Check the vacuum with gauge manifold valve, then close gauge
manifold valve, and stop the vacuum pump.
5)Leave as it is for one or two minutes. Make sure pointer gauge manifold valve remains in the same position. Confirm that pressure gauge
shows –0.101 MPa [Gauge] (–760 mmHg).
6)Remove gauge manifold valve quickly from service port of stop
valve.
7)After refrigerant pipes are connected and evacuated, fully open all
stop valves on both sides of gas pipe and liquid pipe. Operating without fully opening lowers the performance and this causes trouble.
8)Refer to 1-3., and charge the prescribed amount of refrigerant if
needed. Be sure to charge slowly with liquid refrigerant. Otherwise,
composition of the refrigerant in the system may be changed and affect performance of the air conditioner.
9)Tighten cap of service port to obtain the initial status.
10) Leak test
*Close
*Open
Gauge manifold
valve (for R410A)
Service port cap
(Torque 13.7 to
17.7 N•m, 140 to
180 kgf•cm)
Stop valve
for GAS
Stop valve
for LIQUID
Precautions when using
the control valve
A
Close
Open
Control
valve
Vacuum pump
(for R410A)
Service port
When attaching the control valve to
the service port, make sure that the
valve core is in closed position, and
then tighten part A. Do not tighten
part A or turn the body when valve
core is in open position.
Union
Stop valve
Liquid pipe
Perform gas charge to unit.
CAUTION:
When charging the refrigerant system with additional refrigerant, be sure
to use liquid refrigerant. Adding gas refrigerant may change the composition of the refrigerant in the system and affect normal operation of the air
conditioner. Also, charge the system slowly, otherwise the compressor
will be locked.
To maintain the high pressure of the gas cylinder, warm the gas cylinder
with warm water (under 40°C) during cold season. But never use naked
fire or steam.
Charge hose
(for R410A)
When attaching the control valve to
the service port, valve core may deform or loosen if excess pressure is
applied. This may cause gas leak.
Body
4-2.GAS CHARGE
Note:
In case of adding refrigerant, comply with the quantity specified for the
refrigerating cycle.
Handle High
Handle
Low
Hexagonal wrench
Charge hose
(for R410A)
1)Connect gas cylinder to the service port of stop valve.
2)Perform air purge of the pipe (or hose) coming from refrigerant gas
cylinder.
3)Replenish specified amount of the refrigerant, while operating the air
conditioner for cooling.
Compound pressure
–0.101MPa gauge (for R410A)
(–760 mmHg)
Pressure gauge
(for R410A)
Stop valve cap
(Torque 19.6 to
29.4 N•m, 200
to 300 kgf•cm)
*4 to 5 turns
Union
Indoor
unit
Outdoor
unit
*
Union
Stop valve with
service port
Gas pipe
* D unit is for 4B71VA only.
Refrigerant gas cylinder operating valve
(for R410A)
Union
Gauge manifold
valve (for R410A)
Charge hose (for R410A)
Refrigerant gas cylinder
for R410A with siphon
Refrigerant (liquid)
Electronic scale for
refrigerant charging
MXZ-3B_4BVA-A1 JG79A319H01.indd
6
2009/10/13
10:27:03
4-3.REMOVING THE MAINTENANCE PANEL
The setting of Dip Switch on the outdoor controller board can be changed
without removing the front panel.
Follow the procedures below to remove the maintenance panel and set the
Dip Switch.
1)Remove screw(s) which fix the maintenance panel.
2)Remove the maintenance panel, and perform necessary settings.
3)Install the maintenance panel.
Note:
Make sure to fix the maintenance panel securely. Incomplete installation could
cause malfunction.
maintenance panel
4-4. LOCKING THE OPERATION MODE OF THE AIR CONDITIONER (COOL, DRY, HEAT)
• Description of the function:
With this function, you can lock the operation mode of the outdoor unit.
Once the operation mode is locked to either COOL/DRY mode or HEAT
mode, the air conditioner operates in that mode only.
* Initial setting is required to activate this function. Please explain about this
function to your customers and ask them whether they want to use it.
[How to lock the operation mode]
1)Be sure to turn off the main power for the air conditioner before making the
setting.
2)Set the 2nd Dip Switch of SW1 on the outdoor controller board to ON to
enable this function.
3)To lock the operation mode in COOL/DRY mode, set the 1st Dip Switch
of SW1 on the outdoor controller board to OFF. To lock the operation in
HEAT mode, set the same switch to ON.
4)Turn on the main power for the air conditioner.
COOL/DRY
HEAT
4-5. LOWERING THE OPERATION NOISE OF THE OUTDOOR UNIT
• Description of the function:
With this function, you can lower the operating noise of the outdoor unit
when the operation load is small, for example, during nighttime in COOL
mode. However, please note that the cooling and heating capacity can also
be lowered if this function is activated.
* Initial setting is required to activate this function. Please explain about this
function to your customers and ask them whether they want to use it.
[How to lower the operating noise]
1)Be sure to turn off the main power for the air conditioner before making the
setting.
2)Set the 3rd Dip Switch of SW1 on the outdoor controller board to ON to enable this function.
3)Turn on the main power for the air conditioner.
Lower the operating
noise
4-6.TEST RUN
• Be sure to perform the test run for each unit. Make sure each indoor unit operates properly following the installation manual attached to the unit.
• If you perform the test run for all indoor units at once, you cannot detect any erroneous connection, if any, of the refrigerant pipes and the indoor/outdoor
unit connecting wires.
Make sure that the following is done.
• Power is supplied to the unit.
• Stop valves are open.
About the restart protective mechanism
Once the compressor stops, the restart preventive device operates so the compressor will not operate for 3 minutes to protect the air conditioner.
4-7.EXPLANATION TO THE USER
• Using the OPERATING INSTRUCTIONS, explain to the user how to use the air conditioner. (how to use the remote controller, how to remove the air filters, how to remove or put the remote controller in the remote controller holder, how to clean, precautions for operation, etc.).
• Recommend the user to read the OPERATING INSTRUCTIONS carefully.
5. RELOCATION AND MAINTENANCE
5-1.PUMPING DOWN
When relocating or disposing of the air conditioner, pump down the system following the procedure below so that no refrigerant is released into the atmosphere.
1)Connect the gauge manifold valve to the service port of the stop valve on the gas pipe side of the outdoor unit.
2)Fully close the stop valve on the liquid pipe side of the outdoor unit.
3)Close the stop valve on the gas pipe side of the outdoor unit almost completely so that it can be easily closed fully when the pressure gauge shows 0
MPa [Gauge] (0 kgf/cm2).
4)Start the emergency COOL operation on all the indoor units.
To start the emergency operation in COOL mode, disconnect the power supply plug and/or turn off the breaker. After 15 seconds, connect the power
supply plug and/or turn on the breaker, and then press the E.O. SW once. (The emergency COOL operation can be performed continuously for up to 30
minutes.)
5)Fully close the stop valve on the gas pipe side of the outdoor unit when the pressure gauge shows 0.05 to 0 MPa [Gauge] (approx. 0.5 to 0 kgf/cm2).
6)Stop the emergency COOL operation.
Press the E.O. SW several times until all LED lamps turn off. Refer to operating instructions for details.
WARNING
When pumping down the refrigerant, stop the compressor before disconnecting
the refrigerant pipes. The compressor may burst if air etc. get into it.
MXZ-3B_4BVA-A1 JG79A319H01.indd
7
2009/10/13
10:27:08
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
JG79A319H01
MXZ-3B_4BVA-A1 JG79A319H01.indd
8
2009/10/13
10:27:09