Mitsubishi X300U User manual

ENGLISH
ESPAÑOL
ITALANO
DEUTSCH
FRANÇAIS
LCD
Projector
User Manual
MODEL
APPENDIX
X300
LVP-X300U
EN – 1
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interference with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class A device.
This apparatus must be grounded.
The projector automatically shuts off when the
lamp is used up in about 2,000 hours and cannot
be used until lamp replacement.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
EN – 2
When using the projector in Europe
COMPLIANCE NOTICE
This LCD - Video Projector complies with the
requirements of the EC Directive 89/336/EEC “EMC
Directive” as amended by Directive 93/68/EEC and
73/23/EEC “Low Voltage Directive” as amended by
Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B and EN55013. Please
follow WARNINGS instructions.
ENGLISH
Contents
Important safeguards ...........................................................................4
Overview ............................................................................................... 6
Using the remote control ......................................................................8
Battery installation ......................................................................................................... 8
Installation ............................................................................................9
Basic connections ............................................................................... 10
Projector + AV equipment.............................................................................................
Projector + DVD player or HDTV decoder ...................................................................
Projector + personal computer ......................................................................................
For IBM PC or IBM PC compatibles.................................................................
For Macintosh ....................................................................................................
Preparing the projector for operation ...............................................
To operate projector power ON ..........................................................
Menu operation ..................................................................................
Picture adjustment .............................................................................
10
10
10
11
11
12
13
15
18
Specification of RGB signals in each computer mode of the projector ....................... 19
Advanced feature for presentation .................................................... 20
PinP (Picture in Picture) ...............................................................................................
Expand ...........................................................................................................................
Still .................................................................................................................................
Mouse remote control ....................................................................................................
Lamp replacement .............................................................................
Maintenance .......................................................................................
Troubleshooting ..................................................................................
Indicators ............................................................................................
Specifications ......................................................................................
20
20
20
21
22
23
24
25
26
Kensington Lock ............................................................................................................
Connectors .....................................................................................................................
Dimensional drawings ..................................................................................................
Replacement parts list ..................................................................................................
26
27
27
27
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
IBM and VGA are trademarks or registered trademarks of International Business Machines Corporation.
MicroSaver and Kensington are registered trademarks of Kensington Technology Group.
Other brand or product names are trademarks or registered trademarks of their respective holders.
D
EN – 3
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD projector.
1.
Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
10.
Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11.
Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles,
and points where they exit from the appliance.
2.
Retain instructions
The safety and operating instructions should be
retained for future reference.
3.
Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
12.
Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
4.
Instructions
All operating instructions must be followed.
13.
5.
Cleaning
Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
Objects and liquids
Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the projector.
6.
Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, electric shock or other personal injury.
14.
Servicing
Do not attempt to service this projector yourself.
Refer all servicing to qualified service personnel.
15.
7.
Water and moisture
Do not use this projector near water or in contact with water.
8.
Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow the
manufacturer's instructions and should use a
mounting accessory recommended by the manufacturer.
Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
(a)
If the power-supply cord or plug is damaged.
(b)
If liquid has been spilled, or objects have
fallen into the projector.
(c)
If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.
(d)
If the projector has been exposed to rain
or water.
(e)
If the projector has been dropped or the
cabinet has been damaged.
(f)
If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16.
Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17.
Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9.
Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturer's instructions have been adhered to.
EN – 4
Do not turn off the main power
abruptly or unplug the projector
during operation.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
It can lead to lamp breakage, fire, electric shock or
other trouble.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owner's
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face a lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is operating. It may
hurt your eyes.
Never let children look into the lens when it is on.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the projector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free surface: otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious injury and damage to the projector.
• Place the projector within a slope of ±15˚. Slanting
the projector more than ±15˚ may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and ventilation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of
the Department of Communications.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class [A] digital apparatus complies with Canadian ICES-003.
EN – 5
ENGLISH
WARNING:
Unplug immediately if there is
something wrong with your projector.
Overview
4
6
5
1
2
3
4
5
6
7
8
9
Air inlet slots (Front)
Terminal board
Air outlet slots
Speaker (Left/Right)
Control panel
Remote control sensor (Front)
Lens
Remote control sensor (Rear)
Kensington Security Lock Standard
connector
10 Easy-carry handle
7
3
2
1
Control panel
8
14
9
13 12
LAMP
1
10
TEMP
11
ZOOM/
FOCUS
2
10
VOLUME
COMPUTER
VIDEO
3
9
MENU
4
8
ENTER
7
AUTO
POSITION
MUTE
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Power button
– (VOLUME) button
COMPUTER button
MENU button
AUTO POSITION button
MUTE button
Direction buttons
ENTER button
VIDEO button
+ (VOLUME) button
ZOOM/FOCUS button
Temperature (TEMP) indicator
LAMP indicator
Power indicator
1
Main power
6
Terminal board
14
13 12
11
10 9 8
7
REMOTE
USB
RS-232C
COMPUTER 1 IN
AUDIO 1 IN
COMPUTER 2 IN
VIDEO 1 IN VIDEO 2 IN
AUDIO 2 IN
S-VIDEO
VIDEO
MAIN
1
O
COMPUTER OUT AUDIO OUT
I
AUDIO
AC IN
L
2
R
3
EN – 6
4
5
6
I : ON
O : OFF
2
3
4
5
6
7
8
9
10
11
12
13
14
Ground terminal
Power jack
COMPUTER OUT terminal
Audio output jack
Video/audio input terminals
Reset button
Wired remote control (REMOTE) jack
USB terminal
Audio input 2 (AUDIO 2 IN) terminal
RS-232C terminal
COMPUTER 2 IN terminal
Audio input 1 (AUDIO 1 IN) terminal
COMPUTER 1 IN terminal
1
2
3
1
4
5
5
2
Release buttons (Left/Right)
Adjustment foot (Left/Right)
Air inlet cover (bottom) /
Filter cover (For bottom air inlet slots)
Lamp cover
Filter cover (For front air inlet slots)
Caution:
Do not replace the lamp right after using the projector.
The lamp is very hot.
3
4
Remote control
18
MUTE
1
COMPUTER
2
3
4
VIDEO
AUTO
POSITION
ZOOM/
FOCUS
17
16
15
VOLME
LASER
MENU
14
13
12
5
RIGHT CLICK
11
10
ENTER
6
EXPAND
P in P
STILL
9
8
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Power button
COMPUTER button
AUTO POSITION button
MENU button
RIGHT CLICK button (For mouse)
EXPAND button
Wired remote control jack
Picture in Picture (PinP) button
STILL button
Direction buttons
ENTER button
Mouse pointer button
LASER button
+ , – buttons
ZOOM/FOCUS button
VIDEO button
MUTE button
Remote control transmission area
Left click button (For mouse)
•
When pressing the mouse pointer button, all
buttons on the remote control will light up.
The light will be turned off about 10 seconds
after releasing the mouse pointer button.
About laser beam
This remote control is class 2 (max. output 1 mW laser
diode 645 nm) laser equipment.
19
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH : 645nm
MAX OUTPUT : 1mW
CLASS II LASER PRODUCT
CAUTION :
Pressing the LASER button provided remote control emits
laser beam. Do not look into the beam light directly. Do not
point the laser beam at people. Looking the laser beam
directly may damage eyesight.
EN – 7
ENGLISH
Bottom side
Using the remote control
Battery installation
Use two AA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
3. Replace the back cover.
1
2
3
Important:
• Do not use a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area (for wireless control system)
The range for operation is about 10 m when the remote control points to the projector. The distance to the screen
back to the projector must be less than 7 m. Depending on the type of the screen, the distance is different.
30˚
20˚
20˚
15˚
15˚
30˚
20˚
20˚
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
REMOTE
RS-232C
COMPUTER 1 IN
AUDIO 1 IN
COMPUTER 2 IN
USB
VIDEO 1 IN VIDEO 2 IN
AUDIO 2 IN
S-VIDEO
VIDEO
MAIN
O
COMPUTER OUT AUDIO OUT
I
AUDIO
AC IN
L
R
• When the remote control is connected with remote
control cable, it does not work as a wireless
remote control.
• When you need a longer cable, use a pin-pin cable.
• When using the wired remote control, the laser beam may be darker. It is normal.
EN – 8
Installation
Picture size can be set by changing the distance between the screen and the projector.
Front projection
To find the approximate distance
screen
between the projector and screen:
Multiply the width of the screen
✕ 1.9 (min.) , Multiply the width of
the screen ✕ 2.4 (max.).
• Refer to the chart for recommended distances in maximum
zoom and minimum zoom.
L (between the screen and the
head of the projector)
Screen
Diagonal size
(inch)
40 "
60 "
80 "
100 "
120 "
140 "
160 "
180"
200 "
300 "
Height inches
(inch)
24 "
36 "
48 "
60 "
72 "
84 "
96 "
108 "
120 "
180 "
Width feet
(inch)
32 "
48 "
64 "
80 "
96 "
112 "
128 "
144 "
160 "
240 "
Distance from screen (L) / (approximate)
Maximum
Minimum
zoom (min.)
zoom (max.)
(cm)
(inch)
(cm)
(inch)
195
77 "
155
61 "
296
116 "
235
92 "
396
156 "
315
124 "
496
195 "
394
155 "
597
235 "
474
187 "
697
274 "
554
218 "
797
314 "
634
250 "
898
353 "
714
281 "
998
393 "
794
312 "
–
–
1194
470 "
• The above numbers are approximate, and may be slightly different from the actual measurements.
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
SCREEN
• When using the ceiling mount, set IMAGE REVERSE in the INSTALLATION menu to
(Mirror invert). You can not use KEYSTONE
R
when IMAGE REVERSE is set to
(Invert) or
(Mirror invert). See Page 16.
• Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
R
R
Rear projection
Ask a specialist for installation. For more details,
consult your dealer.
SCREEN
´
• For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to R (Mirror). See Page
16.
Caution:
• Placing the projector on a carpet reduces ventilation from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
• Place the projector more than 20 in. from the wall
to prevent blocking the intake, exhaust slots and
ventilation of this projector because hot air comes
out of it.
• Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
• in a dusty or humid place
• while the projector is lying sideways or upside
down
• near a heater
• in a kitchen or oily, smoky or damp place
• in direct sunlight
• with high temperature, such as the closed car
• where the temperature is lower than 41°F or
higher than 104°F
Important:
• Do not put stress on the lens, as this may cause
damage.
EN – 9
ENGLISH
Orientation of the projector
Basic connections
This projector can be connected to equipment such as VCRs, video cameras, videodisc players, and personal computers having analog RGB output.
Important:
• Make sure that your equipment is turned off before connection.
• Plug in firmly and unplug by holding the plug, not by pulling the main power cable.
• If connected units are set too close to one another, the image may be affected.
• Refer to the owner's guide of each component for details of connections.
Projector + AV equipment
Important:
• Match the color of video and audio plugs on the AV cable with the connections.
• S-video signals take priority over video signals. If you input both S-video signals and normal video signals at
the same time, the normal video input automatically is inhibited.
to audio input 1
to S-video
input 2
to video
input 1
to audio input 2
to S-video
input 2
to video input 2
Connect either one of these.
Connect
either one
of these.
to audio to S-video to video
output
output output
DVD player, others
to audio to S-video to video
output
output output
VCR, others
Projector + DVD player or HDTV decoder
Some DVD players have output terminal for 3 line fitting (Y, CB, CR). When connecting them to the projector,
connect to COMPUTER 1 IN or COMPUTER 2 IN of the projector. In this case, set “ Y, CB, CR” for COMPUTER
INPUT setting in SIGNAL menu.
•
•
•
•
•
BNC - RCA connector
(optional)
Y
G
CB(PB) CR(PR)
B
R
No connection
VD
Connecting with HDTV decoder
Many HDTV decoders have HDTV system component video output (Y, PB, PR) terminal. When connecting the projector with this type of HDTV decoder, the COMPUTER INPUT in the SIGNAL
setting menu becomes [Y, PB, PR] automatically.
DVD player or HDTV decoder
HD/CS
Connecting with DVD player
DVD player generally has SDTV system component video output (Y, CB, CR) terminal. When connecting the projector with DVD player, the COMPUTER INPUT in the SIGNAL setting menu becomes [Y, CB, CR] automatically.
to COMPUTER
1 IN
Y, PB, PR is an example of the terminal names for a HDTV decoder.
The terminal name is different depending on the connected equipment.
Use mini D-SUB 15 pin-BNC conversion cable for connection.
Some DVD players may not project the image correctly.
When connecting with HDTV equipment which has R, G, B output, set RGB for the COMPUTER INPUT in the SIGNAL
setting menu.
EN – 10
ENGLISH
Projector + Personal computer
Connection
For IBM PC or IBM PC compatibles
When outputting to both a PC monitor and the projector.
computer
RGB cable for PC
(option)
to COMPUTER OUT
to PC
monitor
to AUDIO IN
PC audio
cable (option)
to PC audio
output
to COMPUTER
IN
to monitor
port
RGB cable for PC
For Macintosh
When outputting to both a PC monitor and the projector.
Monitor Conversion
Monitor cable
adapter (option)
(option)
to PC
monitor
to COMPUTER OUT
to AUDIO IN
PC audio
cable (option)
to PC audio
output
to COMPUTER IN
computer
to video port
6
PID
5
4
3
2
1
NO
RGB cable for PC
MAC adapter for
RGB cable (option)
Important:
• Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector. Please contact your dealer.
• The audio input for a personal computer is a stereo mini jack. There are some personal computers that have
different types of audio outputs or none at all. Please ask your dealer for details.
• A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
• If you use the MAC adapter for RGB cable, set the dip switch to the appropriate position.
´
EN – 11
Preparing the projector for operation
Getting ready for projection
Adjusting the angle of projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting two foot adjustments on the bottom of the
projector.
Warning:
• Do not look directly into the lens when projector is
“ON”.
• The lens cap is for protecting the lens. If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
• This projector is equipped with the power cords for
both U.S. and Europe. Use the appropriate power
cord for your country.
• A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C outlet.
• The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
• Use 100-240V AC 50/60Hz correct voltage otherwise it may lead to fire or electric shock.
• Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid breaking the power cord. A broken power cord can cause
fire or electric shock.
• Do not revise or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is broken.
Caution:
• Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
• Do not plug in or out with wet hands. It may cause
an electric shock.
EN – 12
screen
Adjustment foot
1. Lift the projector to the appropriate angle.
2. Press the buttons by the projector’s adjustable front
feet, this will allow the feet to slide out to the approximate position.
3. Release the foot adjustment buttons to lock the feet
in that position.
4. Rotate the projector feet for fine adjustment.
After using the projector
5. Return the adjustable feet into the projector.
Important:
• Screen on a flat wall with a 90˚ angle to the floor.
• Align projector to produce a full screen display as
illustrated on page 9.
• The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart.
ENGLISH
To operate projector power ON
REMOTE
USB
RS-232C
COMPUTER 1 IN
AUDIO 1 IN
COMPUTER 2 IN
VIDEO 1 IN VIDEO 2 IN
AUDIO 2 IN
3 , 9 , 10
4
AUTO POSITION
S-VIDEO
VIDEO
MAIN
O
COMPUTER OUT AUDIO OUT
I
AUDIO
AC IN
L
R
MUTE
COMPUTER
VIDEO
AUTO
POSITION
ZOOM/
FOCUS
VOLME
button
2 , 11
3 , 9 , 10
6,8
4
6,8
LAMP
LASER
TEMP
5,7
ZOOM/
FOCUS
COMPUTER
MENU
VIDEO
RIGHT CLICK
4
MENU
ENTER
ENTER
EXPAND
AUTO
POSITION
STILL
STILL button
MUTE
button
1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER button.
The light source lamp starts warming up, eventually turning completely on. In case the light source
lamp does not come on, wait for one minute before
switching power on again.
• If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the indicator lamp will blink for
one minute.
indicator
stand-by
when light source lamp is on
light source lamp held off temporarily
LAMP POWER
green
-
red
green
red
Important:
• A darkened image may be seen right after pressing
the POWER button due to warming up of this projector. While warming up, no other commands can
be accepted.
• When the lamp indicator is blinking red, the service life of the lamp is about to end. Replace the
lamp. See pages 22 and 25.
´
P in P
MUTE
AUTO POSITION
button
condition
5,7
• The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4. Select the desired external input source by using
the COMPUTER or VIDEO button.
• The projector automatically selects the appropriate
signal format. The selected signal format is displayed on the screen.
• When selecting the COMPUTER input, the image
may flicker. Press the $ or % button to adjust the
image.
• When input signal is jittering, please adjust by $
or % button also connecting with DVD player or
MUSE decoder etc.
• When supplying unstable signal like Still or
Reverse play with VCR, “NO SIGNAL” may
appear on the screen. In this case, you may avoid
this issue by selecting the right color format like
NTSC, PAL in OPTION menu.
5. Press the ZOOM/FOCUS button to FOCUS. “FOCUS” will appear on the display.
6. Adjust with the + or - button to get a fine picture.
7. Press the ZOOM/FOCUS button to ZOOM. “ZOOM”
will appear on the display.
8. Adjust with the + or - button to get an approximate
size.
• Focus and zoom adjustment is possible in the normal
picture mode only. In PinP or EXPAND mode, the
adjustment is impossible.
EN – 13
To operate projector power ON (Continue)
Turning off the projector
9. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
• To exit from this mode, press any button except
POWER, LASER, mouse pointer, R/L-click,
STILL and VOLUME + and - buttons.
10.Press the POWER button again.
The light source lamp will be turned off.
Pressing the POWER button second time will shut
off the light source lamp, but the exhaust fan continues to operate for 120 seconds to cool down the
light source lamp and LCD panels. In this time, the
lamp indicator will be turned off.
11.Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
• In cases where the main power switch is accidentally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, set the screen to the
brightest display possible, then press the AUTO
POSITION button on the remote control. If the image
is still not in the right place.
• Set screen to the brightest display as possible
(e.g., full-screen display of the “Trash” window)
before deploying the automatic adjustment function.
• If the screen saver is running, turn off the screen
saver before using the automatic adjustment
button.
The volume from the speaker
Press the volume + or – button to change the volume
from the speaker.
The volume control bar will appear on the screen.
30
• The volume control bar will disappear about 10
seconds after releasing the volume buttons.
• The volume buttons do not work when MENU
selection bar or MENU is displayed.
• The volume from the audio output terminals and
PC audio output terminal are not changed.
• If the high level of audio signal, for example DVD
is supplied into PC AUDIO IN terminal, the
speaker out may be distorted.
EN – 14
AV mute
Image and audio are temporarily erased with pressing the MUTE button. To restore the image and
audio to the normal mode, press the MUTE button
again.
• To prevent the damage of the LCD, the image and
audio will be restored automatically to the normal
mode, 10 minutes after setting the AV mute mode.
• The audios from the audio output terminals and PC
audio output terminal are not muted.
Caution:
• When you have finished using this equipment, wait
120 seconds for the exhaust fans to stop. Then turn
off the main switch and unplug the power cable from
the wall outlet, for safety purposes.
• After the lamp is turned off, the lamp cannot be
switched on again for 60 seconds as a precautionary measure. It will take another 60 seconds before
the lamp indicator goes off. If you wish to turn on
the projector again, wait until the indicator is off
then press the POWER button.
• The exhaust fan rotates faster when the temperature around the projector rises.
• When the temperature around the projector becomes
too high, the sign “TEMP!!” blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically .
The projector automatically shuts off when the
lamp is used up in about 2,000. You must replace
the lamp.
SHARPNESS
TINT
COLOR
± 30
± 30
1 (Standard)
2 (High)
3 (Low)
4 (User)
± 10
± 10
± 10
BASS
TREBLE
PinP AUDIO
0-3
0-3
(Main) ,
CONTRAST
BRIGHTNESS
COLOR TEMP.
AUDIO
INSTALLATION
IMAGE REVERSE
KEYSTONE
AUTO POWER ON
AUTO POWER OFF
TEST SIGNAL
OPTION
MENU POSITION
MODE DISPLAY
SPLASH SCREEN
CINEMA MODE
VIDEO SIGNAL
LANGUAGE
SIGNAL
HORIZ.POSITION
VERT.POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
CONTRAST R
± 30
CONTRAST B
± 30
BRIGHTNESS R
± 30
± 30
BRIGHTNESS B
(± 2 : When the source is selected to COMPUTER)
(Displays only when the source is selected to VIDEO)
(Displays only when the source is selected to VIDEO)
(Sub)
R
(Invert) ,
(Mirror invert)
R (Off) , R (Mirror) ,
± 15˚
ON , OFF
0 (Off) , 5 , 10 , 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 55 , 60 min.
ON , OFF
R
PICTURE
(Upper left),
(Lower right)
ON , OFF
ON , OFF
(– : When the source is selected to COMPUTER)
AUTO , OFF
AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
, English , Español , Deutsch , Français , Italiano ,
0 - 999
*
0 - 999
*
0 - 32
0 - 9999
*
RGB , YCBCR , YPBPR
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
ANAMORPHIC
USER
* : Setting range is different
according to the type of
the signal.
Basic operation
Several settings can be adjusted using Menu.
TEST
1. Press the MENU button.
Opt
2. Press the $ or % button to select the OPTION menu.
TEST
3. Press the ENTER button (or } button).
Opt
INSTALLATION
TEST
TEST
IMAGE REVERSE
R
KEYSTONE
0˚
AUTO POWER ON
ON
AUTO POWER OFF
0
TEST SIGNAL
ON OFF
min
*
*
*
*
AUTO POWER ON
ON
AUTO POWER OFF
0
TEST SIGNAL
ON OFF
min
5. Press the $ or % button to adjust auto power off
time.
PICTURE
INSTALLATION
1 - 99
1 - 99
0 - 63
0 - 63
ON , OFF
4. Press the { or } button to select AUTO POWER
OFF.
EXAMPLE: Auto power off time setting
Opt
ENGLISH
Menu operation
AUTO POWER ON
ON
AUTO POWER OFF
30 min
TEST SIGNAL
ON OFF
6. Exit the menu system by pressing the MENU button several times.
• If the menu operation is not working, press the
RESET button on the terminal board using the suitable implement
• If the COMPUTER or VIDEO button is pressed, the
MENU selection bar or MENU will disappear.
• The settings with 2 mark, you should press the
ENTER button after selecting.
EN – 15
Menu operation (continued)
1 PICTURE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher
PICTURE
as the number increases.
CONTRAST
0
BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as
BRIGHTNESS
0
the number increases.
COLOR TEMP.
1/2/3/4
COLOR TEMP.. .. Adjusts color temperature. See page 18.
SHARPNESS
0
SHARPNESS ...... Adjusts the picture sharpness. The sharpness becomes
TINT
0
sharper as the number increases.
COLOR
0
TINT .................... Adjusts the color balance in the image. The color balance
of the image shifts green as the number increases and
shifts to purple as the number decreases (displays only when the source is selected to
VIDEO).
COLOR ................ Adjusts the color intensity of the image (displays only when the source is selected to VIDEO).
Opt
2 AUDIO
BASS ................... Adjusts the level of low frequencies.
TREBLE .............. Adjusts the level of high frequencies.
PinP AUDIO ....... Use to select the audio output in the PinP mode,
or
(Sub).
Opt
(Main)
AUDIO
BASS
1
TREBLE
1
PinP AUDIO
/
3 INSTALLATION
IMAGE REVERSE Use to reverse or invert the projected image. R (Mirror)
is used for rear projection.
(Mirror invert) is effective
INSTALLATION
when the projector is ceiling-mounted.
IMAGE REVERSE
R
KEYSTONE ........ Adjusts keystone correction of the image. If the image has
KEYSTONE
0˚
keystone distortion, select the approximate setting. For
AUTO POWER ON
ON
normal use, select
0˚. You can use it only when IMAGE
R
AUTO POWER OFF
0 min
REVERSE is
(Invert) or (Mirror invert).
TEST SIGNAL
ON OFF
AUTO POWER ON ..... To select whether to boot up automatically when the power is
turned on external to the projector. In this case, the main
power switch of the projector has to be ON. Set this when the projector is hanging on the ceiling.
• The projector is in stand-by mode when the lamp is not on. In this case, use the remote
control to turn on the lamp.
AUTO POWER OFF .. Use to select the length of time before projector switches to stand-by when there is no input
signal selected source. Select 0 min. to cancel this function.
TEST SIGNAL .... Use to display the built-in test patterns on the screen.
• The display will disappear when the setting is OFF or when you press any button except
MENU, { ,}, STILL, LASER, mouse pointer or R/L-click.
Opt
R
R
TEST
4 OPTION
MENU POSITION . Use to select the position where the menu is displayed,
(upper left) or
(lower right).
OPTION
MODE DISPLAY ... Use to display the mode display on the screen.
MENU POSITION
SPLASH SCREEN . Use to display the splash screen on the screen when the
MODE DISPLAY
ON
power is turned ON.
SPLASH SCREEN
ON
CINEMA MODE .... When AUTO is set, the video signal is processed
CINEMA
MODE
AUTO
appropriately for cinema source during inputting the
AUTO
cinema source with NTSC format. If the video signal is ? VIDEO SIGNAL
LANGUAGE
English
processed during inputting the other source, set to OFF.
Ë
• When setting CINEMA MODE to AUTO, some images
may not switch to cinema mode during inputting the cinema source.
• When setting CINEMA MODE to AUTO, images may not switch to video mode immediately after switching the cinema source to video source. At that time, the image quality
of the video source may get worse. If you wish to switch the mode immediately, press
ENTER button.
VIDEO SIGNAL . When AUTO is set, the appropriate video format is automatically selected according to the
input signal. If the image does not appear correctly, select the desired video format
manually. Adjust the unit to the appropriate format when the unit either is not projecting
normally in auto mode or is projecting PAL-M/PAL-N signals.
LANGUAGE ....... Use to select the language for the projector display such as menu. (
/ English / Español
/ Deutsch / Français / Italiano /
)
Opt
ON
ON
A
EN – 16
ENGLISH
5 SIGNAL
HORIZ. POSITION .... Use to adjust the horizontal position of the image.
VERT. POSITION ..... Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
Opt
SIGNAL
HORIZ. POSITION
0
VERT. POSITION
0
TRACKING ......... Use to avoid image noise such as wide stripes.
FINE SYNC.
0
COMPUTER INPUT .... The unit adjusts itself automatically when connected to
TRACKING
0
either DVD players with a component video output
COMPUTER INPUT
RGB
terminal (YC BCR or YPBP R ) or equipment with HDTV
USER
signal output capabilities. In cases where the unit is
connected to equipment that include an RGB output terminal and which output HDTV
signals, adjust the unit to RGB mode.
RRGGBB
• In case of the HDTV, you cannot adjust the horizontal position and the vertical position of the image.
6 SIGNAL - USER (Normally, there is no need for adjustments.)
HOLD BEGIN /
HOLD END ...... Adjusts the image when curving near the top.
CLAMP POSITION/
CLAMP WIDTH .........If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
ANAMORPHIC ... Set to ON when displaying DVD discs which are recorded
as squeezed images (in right and left direction).
USER
HOLD BEGIN
1
HOLD END
1
CLAMP POSITION
0
CLAMP WIDTH
0
ANAMORPHIC
ON
EN – 17
Picture adjustment
Adjusting the image
You can adjust the picture by using the IMAGE menu.
EXAMPLE: USER setting of COLOR TEMP.
1. Select COLOR TEMP in IMAGE menu.
2. Press the $ or % button to select 4 2.
3. Press the ENTER button.
Adjusting the images form personal
computers in MENU display
Adjust as below for the following symptoms.
Opt
SIGNAL
HORIZ. POSITION
0
COLOR TEMP.
CONTRAST R
VERT. POSITION
0
FINE SYNC.
0
TRACKING
0
COMPUTER INPUT
RGB
0
CONTRAST B
0
BRIGHTNESS R
0
BRIGHTNESS B
0
RRGGBB
USER
4.
5.
6.
7.
Press the { or } button to select the desired item.
Press the $ or % button to adjust the item.
Repeat steps 4 and 5 for more adjusting.
Exit the menu system by pressing the MENU button several times.
Opt
PICTURE
CONTRAST
0
BRIGHTNESS
0
COLOR TEMP.
1/2/3/4
SHARPNESS
0
TINT
0
COLOR
0
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu. Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu. Press the %
button to lighten the image and the $ button to
darken the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu. Press the %
button to make the picture seem sharper and the $
button to make it softer.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu. Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu. Press the % button
to increase the amount of red in the image and the $
button to increase the amount of green in the image.
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers. In this case, press the AUTO POSITION
button. If the images are still not projected correctly,
use the MENU display to adjust the projected images.
EN – 18
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu. Press
the % button to move the image to left. Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu. Press
the % button to move the image to upward. Press
the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
USER
HOLD BEGIN
1
HOLD END
1
CLAMP POSITION
0
CLAMP WIDTH
0
ANAMORPHIC
ON
Top part of image curves :
Adjust HOLD BEGIN or HOLD END in USER menu
for image which top part is the least curved.
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL USER menu. Select AUTO for normal setting.
• Do not change each menu setting in USER menu
for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left end).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right end).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end).
Signal mode
TV60
TV50
HiVision
PC98
CGA70
CGA85
VGA60
VGA72
VGA75
VGA85
SVGA56
SVGA60
SVGA72
SVGA75
SVGA85
XGA43i
XGA60
XGA70
XGA75
XGA85
SXGA70a
SXGA75a
SXGA85a
SXGA60a
SXGA75a
SXGA43i
SXGA60
SXGA75
SXGA85
MAC13
MAC16
MAC19
MAC21
HP75
HP72
SUN66a
SUN76a
SUN76
IBM60
resolution
(H x V)
–
–
–
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 960
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
640 x 480
832 x 624
1024 x 768
1152 x 870
1024 x 768
1280 x 1024
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
horizontal
frequency (kHz)
15.73
15.63
33.75
24.82
31.47
37.86
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
35.52
48.36
56.48
60.02
68.68
63.85
67.50
77.49
60.00
75.00
46.43
63.98
79.98
91.15
35.00
49.72
60.24
68.59
62.94
78.13
61.85
71.81
81.13
63.42
• Pressing the EXPAND button on the remote control
twice will switch to the screen displaying the picture as its original size (real screen display). In the
real screen display, pictures will be black-framed
when picture resolution is lower than 1,024 x 768.
Important:
• Some computers may not be compatible with the
projector.
• The projector's maximum resolution is 1,024 x 768
pixels. It may not display correctly for the pictures
of higher resolutions than 1,024 x 768.
• The picture with a SYNC on G (Green) signal may
jitter.
• The picture with a SYNC on G (Green) signal may
be tinged with green.
Vertical
frequency (Hz)
59.94
50.00
60.00
56.42
70.09
85.08
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
86.96
60.00
70.07
75.03
85.00
70.01
75.00
85.06
60.00
75.00
86.87
60.02
75.03
85.02
66.67
74.55
75.02
74.96
74.92
72.00
66.00
76.63
76.11
60.00
Normal mode
(H x V)
1024 x 768
1024 x 768
1024 x 576
1024 x 640
1024 x 640
1024 x 640
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
960 x 768
960 x 768
960 x 768
960 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
960 x 768
984 x 768
984 x 768
960 x 768
960 x 768
ENGLISH
Specification of RGB signals in each computer mode of the projector
Real mode
(H x V)
–
–
–
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
–
640 x 480
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
• If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible resolution and frequency.
• Set the COMPUTER INPUT in SIGNAL menu to RGB,
when inputting the HDTV signal as RGB signal.
• In case of the HDTV, the image quality may be
reduced, principally.
About DDC™
The projector complies with VESA™ DDC™1/2B (EDID)
specification. If your computer provides DDC™1/2B
(EDID) function, setup will be done automatically. For
use this function, you must down load the driver from
our Internet Home Page. Please contact your dealer or
Mitsubishi sales office for more details.
EN – 19
Advanced features for presentation
PinP (Picture in Picture)
Expand
One of the special features of this unit is the picturein-picture (PinP) mode. PinP allows you to view different sources at the same time.
By pressing the EXPAND button on the remote control, you can view the detailed image of the picture.
You can also view the screen diplaying the picture as
its original size (real screen display) by pressing the
button again.
1. Press the PinP button on the remote control.
The sub image will appear.
Main image
(From COMPUTER IN)
Sub image
(From VIDEO IN)
• Pressing the PinP button repeatedly will select
on and off.
• You can change the position of the sub image by
pressing the {, }, $ or % button.
• You can change the size of the sub image by
pressing the + or - button.
2. If necessary, select the desired external input source
of the sub image by using the VIDEO button.
• You can change the external input source of the
main image by using the COMPUTER button.
3. Press the PinP button on the remote control again.
The sub image will be disappeared.
• During PinP mode, the audio selected in PinP
AUDIO of the AUDIO menu is outputted.
• During PinP mode, you cannot adjust the zoom/focus
and the volume.
• Adjusting contrast, brightness, tint or color isn't
available during PinP mode.
• When connecting DVD player or MUSE decoder
etc. to COMPUTER IN terminal, PinP are not
available.
• During PinP mode, the expand mode is not available.
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active picture by pressing the {, }, $ or % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button on the remote control
again.
The real screen display will appear on the screen.
3. Press the COMPUTER or VIDEO button.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
• In EXPAND mode or REAL mode, pressing the
COMPUTER or VIDEO button will switch to the
normal screen display .
The normal screen display will appear on the screen.
• In EXPAND mode, you cannot adjust the zoom/focus and the volume.
• When displaying the images through VIDEO IN
terminal or the video images through COMPUTER IN terminal, expanded image display is
not available. Only real screen display is available.
• During expand mode, the PinP mode is not available.
REAL screen display
• During REAL mode, Press the $ or % buttons
for fine adjustment. the { and } buttons are
not working at this time.
• The expanding rate cannot be changed by
pressing either the + or - button. They are
working for volume adjustment.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will stop temporary.
To resume picture activity.
2. Press the STILL button on the remote control
again.
EN – 20
By connecting to personal computer through the USB, PS/2 or ADB port, you can operate your computer with the
projector remote control.
Connection
Projector + PC with USB connector
to USB
to USB port
USB cable
USB 4P
(type A)
USB 4P
(type B)
• You can use the mouse remote control function with computer supported USB only. If your system is Windows® 98 or higher, your computer supported USB in standard. If your system is Windows® 95 or lower,
please contact your dealer. If your computer is Macintosh with USB port, you can use this function.
Projector + IBM PC or IBM PC compatibles
to RS-232C
terminal
to mouse
(PS/2) port
RS-232C cable
PS/2 adaptor
Mini DIN 6P
D-SUB 9P
D-SUB 9P
D-SUB 9P
Projector + Macintosh
to ADB port
MAC adaptor
for MOUSE (option)
Mini DIN 4P
D-SUB 9P
to RS-232C
terminal
RS-232C cable
D-SUB 9P
D-SUB 9P
Operation
MUTE
COMPUTER
VIDEO
AUTO
POSITION
ZOOM/
FOCUS
VOLME
MENU
LASER
left click
This operates in the same
way as the left button on
the computer mouse.
mouse pointer
Use to move the cursor on the image,
instead of the computer mouse.
right click
RIGHT CLICK
This operates in the same way as the right
button on the computer mouse.
ENTER
• If the mouse remote control is not working, restart the computer.
EN – 21
ENGLISH
Mouse remote control
Lamp replacement
The lamp is designed to project the image on the LCD
panels. When the lamp no longer functions, replace it
with a new one.
Caution:
• Do not remove the lamp immediately after using
the projector, you may get burned because of the
high temperature of the lamp.
• When you replace the lamp, press the power button
to power off, then wait for 120 seconds in stand-by
mode to allow the lamp and LCD panels to cool. Turn
off the main switch, unplug the power cord from
the outlet, and wait one hour so that the lamp is
cooled to the touch.
• Do not remove the lamp except for replacement.
Careless treatment can cause injury or fire.
• Do not touch the lamp element directly. It may break
and cause you to injure or burn yourself.
• Be sure not to drop the lamp lid screw into the projector. Also be sure not to insert metal or any flammable objects, it may cause fire or electric shock. If
any objects are inserted, please unplug and contact
your dealer.
• Install the lamp securely, failure may cause a fire.
(a)
7. Tighten up the screws of the lamp
lid using a phillips screwdriver
(+).
How to reset the operation time meter
Plug in the power cord, switch on the projector, and
reset lamp time by pressing the $, % and POWER
buttons simultaneously.
Important:
• If the 3 buttons was not pressed at the same time,
the lamp time may not be reset.
• Please confirm the TEMP indicator illuminates
about 2 seconds and the lamp time has been
reset.
• The projector will not turn on if you do not secure
the lamp lid.
• You must reset the operation time meter after you
replace the lamp.
• Do not reset the operation time meter unless the
lamp has been replaced.
Caution:
• Do not spill liquid on the lamp or place it near flammable objects or where children can touch it. Otherwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted
between the right and left lamp guides.
1. Reverse the projector gently.
2. Loosen the screws of the
lamp lid on the top cover using a phillips screwdriver
(+) , and remove the lid.
• Remove the lamp cover in
the direction of the arrow
as indicated.
6. Tighten up the screws (a) using a
phillips screwdriver (+).
Screw of the lamp lid
The life of the lamp
(a)
3. Loosen screws (a) using a phillips
screwdriver (+), and remove them.
Handle
4. Hold onto the projector by the handle as
you pull out the lamp.
Once the lamp has been removed, do not
spill liquid on it, place it near flammable
objects or where children can touch it.
Otherwise, it will cause injury or fire.
5. Insert the new lamp securely into the
projector body in the right direction.
The average life of the lamp for the projector is about
2,000 hours of consecutive use. Life span may differ
according to operating environment, and may be shorter
than 2,000 hours. Decreases in luminescence and/or
color brightness will indicate that the light source lamp
needs to be replaced. When lamp operation time exceeds 1,500 hours, the indicator will flash alternately
between green and red (while the lamp is in operation;
when the lamp is not in operation, the indicator will
appear red only). When the lamp has been used for
about 1,900 hours, the message “LAMP!!.” will appear
on the screen for one minute. When the lamp has been
used for about 2,000 hours, the projector will automatically shut off for the safety of the lamp and the power
indicator light will be red. The projector cannot be used
until the lamp has been replaced and operation timer
has been reset.
Caution:
• The lamp is fragile. If broken, be careful not to cut
yourself with glass fragments.
• The lamp life depends on the environment. For replacement lamps, please contact your dealer.
The projector automatically shuts off after about 2,000 hours, and you cannot use
the projector until you replace the lamp.
EN – 22
Caution:
Be sure to turn off the projector and unplug the power
cord from the wall outlet before you perform any maintenance on the projector.
Caution:
Be sure to use the projector with an air-filter. If not,
dust may get inside the projector, causing a fire or a
breakdown.
Cleaning the air-filter
Cleaning the projector and the ventilation
slots
This projector has two air-filters, for bottom air-outlet
slots and for front air outlet slots. Clean the air-filter
frequently. If the filter or ventilation slots become clogged
with dirt or dust, the temperature inside the projector
may rise and shut off the power (the TEMP indicator
starts to blink red).
Filter cover
(For front air outlet slots)
Filter cover
(For bottom air
outlet slots)
Use a soft cloth to clean the projector and the ventilation slots. When the slots become dirty, wipe them with
a soft cloth dampened with a diluted mild detergent,
and then wipe them with a dry cloth.
To protect the surface of the projector from fading or
deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials come into
contact with the projector.
Cleaning the lens
Use a standard lens-cleaning brush or a piece of lens
tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive
lens-cleaning materials. Do not touch the lens with your
fingers.
For bottom air outlet slots
1. To remove the filter cover, press the ridged
area gently, push the cover in the direction
of the arrow and lift.
2. Remove the air-filter from
the filter cover.
3. Wash the air-filter.
• Use water or a mild
detergent diluted with
Filter cover
water to clean the filter.
Rinse the filter thoroughly and let it dry
completely.
Filter
4. Attach the filter to the cover.
5. Reinstall the filter cover.
For front air outlet slots
1. To remove the filter cover, press the
two ridged area gently and pull the cover.
2. Remove the dust from the
air-filter by using a vacuum
cleaner.
• Do not wash the airfilter.
Air-filter
Filter cover
3. Reinstall the filter cover.
Important:
• If the filter is damaged or becomes extremely
dirty, contact your dealer for replacement.
• The power will not turn on if the air-filter cover is
improperly installed.
EN – 23
ENGLISH
Maintenance
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult
this chart before contacting your dealer.
PROBLEMS
The power is off.
CAUSE
• The air inlet slots, outlet slots or air filter is
clogged with dust or some objects.
POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
POWER indicator blinks red.
• The projector has been turned on again too soon
after having been turned off.
• When the power switch was turned off while
the fan was running, during or after lamp
operation.
• The room temperature is too high.
(Does the LAMP indicator show an unusual
condition?)
• Lamp is no longer working.
POWER indicator blinks between red and green.
• The filter cover is not closed.
• When the LAMP indicator or the TEMP
indicator is either on or blinking, the main unit
requires repairs.
No picture appears • Lens is covered by lens cap.
on the screen.
• When the LAMP indicator or the TEMP
The image is
turned off.
• Remove the object.
•
•
•
•
Plug the power cord into the outlet.
Insert the power cord into the projector.
Turn the main switch on.
Close the lamp lid.
• Wait for the lighting sequence.
• Turn the power switch on and off several times.
• Refer to "Indicators" on page 25.
• Replace the lamp with a new one.
• Close the cover correctly.
• Contact your dealer.
• Take the lens cap off.
• Replace the lamp with a new one.
indicator is either on or blinking, the main unit
requires repairs.
• The equipment connected to this projector is not
turned on.
• Hookup is not made correctly with other equipment.
• The input source is not selected correctly.
• Turn on the connected equipment.
• The air inlet slots, outlet slots or air filter is
clogged with dust or some objects.
(In this case, the TEMP indicator does not light up.)
• Remove the object and turn off the main power
switch. After about 10 minutes, Turn the projector on.
The image is
• The projector is not at a right angle to the screen.
distorted.
The image is dark. • Brightness, tint and color are not adjusted correctly.
The image is
blurred.
POSSIBLE SOLUTIONS
• The projecting distance is beyond the focused area.
• Lens is dirty.
• Screen size exceeds screen size specifications.
•
•
•
•
Brightness and contrast are not adjusted correctly.
FINE adjustment is not made correctly.
Tracking is not adjusted.
The projector is not at a right angle to the screen.
• Confirm the hookup.
• Select the correct source according to the equipment connected to this projector.
• Adjust the angle of the projector to make a right
angle to the screen. See page 12.
• Adjust brightness, tint and color correctly.
•
•
•
•
•
•
•
Adjust the projecting distance. See page 9.
Clean lens.
Reduce screen size to within 40" to 300".
Adjust brightness, contrast.
Make FINE adjustment.
Adjust tracking.
Adjust the angle of the projector to make a
right angle to the screen. See page 12.
When
you
see
the
stationary
image
for
a
long
time,
it
may remain on the screen if you change the
The image remains •
image.
It
is
not
a
breakdown.
The
blurred
image
will
disappear
in a few minutes.
blurred.
Red, blue or green dots are • It is normal.
viewed on the text of image.
The image is distorted on the screen
and noise is heard.
• The cable for connection with other equipment
is not plugged securely into the terminal.
• The projector is installed too close to other
equipment.
• Plug the connecting cable securely into the
terminal. See pages 10-11.
• Install the projector far away from other equipment.
No sound is heard.
• Volume is not turned up.
• Connection to other equipment is not made correctly.
• Turn up the volume.
• Check connections. See pages 10-11.
Nothing is displayed on
the PC monitor.
Warm air comes out of
the exhaust vents.
Adjustments cannot be
made.
• The PC monitor is not turned on.
• Turn on the monitor.
EN – 24
• This is typical of the LCD projector.
• The operation is incorrectly made due to noise or
interference.
• Press the reset button on the Terminal board.
See page 15.
Indicators
The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your
dealer.
POWER indicator
LAMP indicator
TEMP indicator
LAMP
TEMP
ZOOM/
FOCUS
VOLUME
COMPUTER
VIDEO
MENU
ENTER
AUTO
POSITION
MUTE
Normal condition
POWER LAMP TEMP
Steady
red
Off
Off
Steady
green
Blinking
green
Off
Steady
green
Steady
green
Off
CONDITION
Notes
Stand-by
Lamp stand-by (about for 1 minute)
The power button cannot be used to switch
ON and OFF
The POWER is ON. (Normal condition)
Abnormal condition
POWER LAMP TEMP
CONDITION
POSSIBLE SOLUTIONS
Unusual temperature
Steady
green
Steady
green
Blinking
green
Steady
red
Off
Steady
red
Steady
green
Blinking
green/red
Off
Lamp duration warning. (Lightning duration total
about 1, 500 hours.When the POWER is ON.)
Steady
red
Blinking
red
Off
Lamp duration warning. (Lightning duration total
about 1, 500 hours.When the POWER is OFF.)
Steady
red
Steady
red
Off
Lamp duration warning. (Lightning duration total
about 2,000 hours.)
Blinking
green/red
Off
Off
Steady
or
Steady
or
Blinking
Blinking
• The ventilation slits or air filter is clogged with
dust or debris.
• The fan has stopped due to an impediment.
• The room temperature is too high.
• The filter is dirty.
• Remove the object from the ventilation
slits.
• Pull out the power plug andremove the
object. If you cannot, consult your dealer.
• Relocate the projector to a cooler place.
• Clean the filter.
Replace the lamp.
Exchange with a new lamp if the same
problem recurs.
The lamp or filter cover is not closed.
Close the cover correctly.
Abnormal.
Contact your dealer.
Blinking
green/red
EN – 25
ENGLISH
The projector has three indicators each of which shows the working condition of the projector.
Specifications
Type
Model
Rated power supply
Rated input
LCD panels
LCD projector
LVP-X300U
AC100 ~ 240V, 50 / 60Hz
2.9 A
1.3-inch LCD panel: 3 pieces (for R, G, B)
Pixels
1,024 × 768 = 786,432 pixels
Total 2,359,296 pixels
Active pixel rate: 99.99 % or more (each panel)
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
16,770,000 colors
F 1.8~2.2
f = 52 ~ 66 mm
190 W NSH
40 ~ 300 inch (aspect ratio 4:3)
Resolution : 640 x 400 - 1024 x 768 + Compressed 1280 x 1024
Sync on Green available
Video compatibility
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
DVD (Component) / HDTV (1080i)
Audio output
Speaker
S-video input
2 W stereo
6 cm square type (8Ω 2W) ×
2
Luminance signal: 1.0 Vp-p 75Ω
(negative sync.)
Chroma signal: 0.286 Vp-p 75Ω (burst signal)
Video input
Audio inputs
Analog RGB input
(mini D-SUB 15P)
1.0 Vp-p 75Ω (negative sync.)
350 mVrms, 10kΩ or more
RGB: 0.7Vp-p 75Ω (negative sync.)
YCBCR: Y:1.0Vp-p (negative sync.) CBCR:0.7Vp-p
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
PC audio input
Control connector
350 mVrms, 10kΩ or more
ø3.5mm stereo mini jack
Serial (D-SUB 9 pin female connector) RS-232C standards
PS/2 (Mouse function), USB terminal for Mouse, Wired remote terminal
Outside dimensions
299 × 127 × 367 mm
(width ×
Weight
Length of power cord
Temperature, humidity
(performance guarantee)
height ×
depth)
Legs and lens are not included.
Approx. 6.0kg
114 inch (2.9m)
+41°F (+5°C) ~ +104°F (+40°C), 30~90%
Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the Kensington System for instructions on how to use it to
secure the projector. Please contact to Kensington Technology Group as shown below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : (650)572-2700
EN – 26
Fax : (650)572-9675
11
PC analog RGB input
Use to input video signals (analog
RGB) of a personal computer.
15
RS-232C input
1
Use to control the projector with the
personal computer, or control the
personal computer with remote
control. Please use RS-232C crossover
5
(Pin assignment of Mini D-SUB 15P jack)
PIN NO.
1
2
3
4
5
6
7
8
SPEC
R(RED)/CR
G(GREEN)/Y
B(BLUE)/C B
GROUND
GROUND
GROUND
GROUND
GROUND
PIN NO.
9
10
11
12
13
14
15
1
5
6
9
cable provided.
SPEC
–
GROUND
GROUND
DDC-DATA
HD/CS
VD
DDC-CLK
PIN NO.
NAME
I/O
1
2
3
4
5
6
7
8
9
DCD / CLOCK
RXD
TXD
N.C.
GND
DTR
CTS / 5V
RTS
RI / DATA
IN
IN
OUT
–
–
IN
IN / OUT
IN
OUT
367
Dimensional drawings
(mm)
98.5
127
81.5
75
16
92
21
51.5
247
330
299
What’s included in the box
2 AC power cable
1
1
1
1
1
Video cable
Audio cable
RGB cable for PC
RS-232C cable
PS/2 adapter
246C346-10
246C346-20
246C323-10
242C938-10
246C318-10
246C320-20
246C367-10
1
1
1
1
1
2
USB cable
Remote control
Remote control cable
User’s manual
Quick reference card
Battery for remote
246C376-10
939P790-10
246C217-30
871D280-20
857B017-10
–
Replacement part
(Option / Not included in the box)
Spare mercury lamp
499B021-10
(VLT-X300LP)
EN – 27
ENGLISH
Connectors
LCD
Projector
User Manual
MODEL
APPENDIX
X300
LVP-X300U
AP – 1
Control this projector by using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
Functions can be controlled by a personal computer:
• Turn the ON or OFF
• Changing input signals
• Button input by remote control or control panel
• Reading warning data
• Menu setting
Connection
Projector + IBM PC or IBM PC compatibles
to modem port
or printer port
to RS-232C
terminal
to Com1
Comport
RS-232C adaptor
for Macintosh (option)
RS-232C cable
D-SUB 9P
Note:
to RS-232C
terminal
D-SUB 9P
Mini DIN 8P
D-SUB 9P
D-SUB 9P
D-SUB 9P
If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin
serial port adapter is required. Contact your dealer for details.
1) Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
FLOW CONTROL
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bits]
NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable,the reverse type cable should be used.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the
command is different by each function.
HEX
ASCII
Address code
30h 30h
'0' '0'
[Address code]
[Function code]
[Data code]
[End code]
AP – 2
Function code
Function
Function
Data code
Data
Data
End code
0Dh
30h 30h (In ASCII code, '0' '0') fixed.
A code of each fixed control move.
A code of each fixed control data (number) and not always indicated.
0Dh (In ASCII code, ' ') fixed.
3) Control sequence
(1) The command from a personal computer to the projector will be sent in 400ms.
(2) The projector will send a return command 400ms* after it has received an encode. If the command isn’t
received correctly, the projector will not send the return command.
(3) The personal computer checks the command and confirms if the command which has been sent has been
executed or not.
(4) This projector sends various codes other than the return code. When having a control sequence by RS232C, reject other codes from personal computer side.
•
* : The sending time of return command may delay depending on the condition (during changing the
input signal, etc.).
[Example] Turn the power ON (' 'is for ASCII code)
Sending commands
from the PC etc.
30 30 21 0D
'0' '0' '!' ' '
Status code from
projector
Meaning
Command for POWER ON
30 30 21 0D
'0' '0' '!' ' '
Command received
(Command echo back)
4) Operation commands
The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal.
Operation
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT VIDEO 1
INPUT VIDEO 2
ASCII
!
"
_r1
_r2
_v1
_v2
HEX
21h
22h
5Fh
5Fh
5Fh
5Fh
72h
72h
76h
76h
31h
32h
31h
32h
• POWER OFF command will not work for 1 minute after the power is turned on.
• POWER ON command will not work for 1 minute after the power is turned off.
[Example] Set the input signal to COMPUTER 1 (' 'is for ASCII code)
Sending commands
from the PC etc.
30 30 5F 72 31 0D
'0' '0' '_' 'r' '1' ' '
Status code from
projector
30 30 5F 72 31 0D
'0' '0' '_' 'r' '1' ' '
Meaning
Command for setting the input
signal to COMPUTER 1
Command received
(Command echo back)
5) Remote commands
Some remote control operations can be done by remote command codes.
ASCII
r06
r07
ra6
r02
r04
r53
r2b
r4f
r59
r54
r10
r0f
r09
ra4
HEX
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
72h
30h
30h
61h
30h
30h
35h
32h
34h
35h
35h
31h
33h
30h
61h
36h
37h
36h
32h
34h
33h
62h
66h
39h
34h
30h
66h
39h
34h
APPENDIX
Button's name on remote
+ VOLUME
– VOLUME
MUTE
EXPAND
PinP
{
}
$
%
MENU
ENTER
ZOOM/FOCUS
AUTO POSITION
STILL
AP – 3
Control this projector by using a personal computer (Continued)
[Example] Display MENU selection bar. (' 'is for ASCII code)
Sending commands
from the PC etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' ' '
Status code from
projector
Meaning
Command as same as MENU button
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' ' '
Command received
(Command echo back)
6) Warning commands
Read the past warning data. The personal computer doesn’t attach the data code onto the warning commands
to send. On the other hand, the projector which has received a command attaches the warning data as the
data code to reply.
ASCII
Ep1
Ep2
Ep3
Ec
past data 1 (newest)
past data 2
past data 3
clear past data
HEX
45h
45h
45h
45h
70h
70h
70h
63h
31h
32h
33h
The past data
Ep* (* is 7 digits, hexadecimal notation)
*=(MBS)b1,b2,b3,b4,b5,b6,b7,b8, b9, b10, b11, b12, b13, b14, b15, b16, b17, b18, b19, b20, b21, b22, b23, b24, b25, 0, 0, 0(LSB)
b1=Operation time (during boot up '0' / when the power is ON, '1')
b2=Communication error between microcomputer and IC PIO1
b3=Communication error between microcomputer and IC PIO2
b4=Communication error between microcomputer and IC PIO3
b5=Communication error between microcomputer and IC PIO4
b6=Communication error between microcomputer and IC PIO5
b7=Stand-by power short
b8=Switch power short (SC connector)
b9=Switch power short (SP connector)
b10=Switch power short (SD connector)
b11=The air inlet fan is stopped
b12=The air outlet fan is stopped
b13=The power fan is stopped
b14=The audio fan is stopped (This fan is not installed.)
b15=The lamp cover is not closed
b16=The filter cover (bottom) is not closed
b17=The filter cover (front) is not closed
b18=The temperature sensor is off (SZ connector)
b19=Communication error between microcomputer and decoder
b20=Abnormal temperature (outside)
b21=Abnormal temperature (lamp)
b22=Abnormal temperature (LCD)
b23=Abnormal temperature (The difference value of lamp from outside)
b24= The life of a lamp
b25=The lamp is not illuminating.
[Example 1]
The outlet fan was down when the power was ON and the newest past data of the warning was confirmed.
Sending commands
from the PC etc.
30 30 45 70 31 OD
'0' '0' 'E' 'p' '1' ' '
Status code from
projector
Meaning
Command to confirm past data
30 30 45 70 38 30 31 30 30 30 30 0D
'0' '0' 'E' 'p' '1' '8' '0' '1' '0' '0' '0' '0' '
Warning command (Outlet fan is stopped when
the power is ON) carried out
'*
* : '8' '2' '0' '0' '0' '0' mean the numbers as shown below
Bit
b1
b2
b3
b4
b5
b6
b7
b8
b9 b10 b11 b12 b13 b14 b15 b16 b17 b18 b19 b20 b21 b22 b23 b24 b25
0
0
0
ASCII
1
0
0
0
0
0
0
0
0
0
0
0
HEX
8
0
0
0
1
1
0
0
0
0
b1=1(The power is ON), b12=1(The outlet fan is stopped), Other= 0
AP – 4
0
0
0
0
0
0
0
0
0
0
0
0
0
7) Reading command diagram
Monitor projector operation status. The power ON, OFF and input terminal settings can be monitored.
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT VIDEO 1
INPUT VIDEO 2
Function
vP
vP
vI
vI
vI
vI
ASCII
Data (Receive)
1
0
r1
r2
v1
v2
Function
76h 50h
76h 50h
76h 49h
76h 49h
76h 49h
76h 49h
HEX
Data (Receive)
31h
30h
72h 31h
72h 32h
76h 31h
76h 32h
When a personal computer sends the command, data code will not be attached. On the other hand, the projector
which has received a command will attach the recent operating status and then send.
[Example ] Input was Video 1 when the operating status of the input terminal was confirmed.
Sending commands
from the PC etc.
30 30 76 49 OD
'0' '0' 'v' 'I' ' '
Status code from
projector
Meaning
Command to confirm input
30 30 76 49 76 31 0D
'0' '0' 'v' 'I' 'v' '1' ' '
Command (Input is Video 1)
carrired out
8) Menu setting commands
ITEM
CONTRAST
BRIGHTNESS
COLOR TEMP.
SHARPNESS(COMPUTER input)
SHARPNESS(VIDEO input)
TINT
COLOR
BASS
TREBLE
PinP AUDIO
IMAGE REVERSE
KEYSTONE
AUTO POWER ON
AUTO POWER OFF
TEST SIGNAL
MENU POSITION
MODE DISPLAY
SPLASH SCREEN
CINEMA MODE
VIDEO SIGNAL
ASCII
P
Q
A
R1
R2
S
T
AUB
AUT
AUP
IR
KS
APON
APOF
TS
MP
MD
SS
CM
VS
HEX
50h
51h
41h
52h
52h
53h
54h
41h
41h
741h
49h
4Bh
41h
41h
54h
4Dh
4Dh
53h
43h
56h
55h
55h
55h
52h
53h
50h
50h
53h
50h
44h
53h
4Dh
53h
LANGUAGE
LG
4Ch
47h
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
ANAMORPHIC
HP
VP
FN
TRK
CIN
HLB
HLE
CLP
CLW
SC
48h
56h
46h
54h
67h
48h
48h
43h
43h
53h
50h
50h
4Eh
52h
49h
4Ch
4Ch
4Ch
4Ch
43h
31h
32h
42h
54h
50h
4Fh
4Fh
4Bh
4Eh
42h
45h
50h
57h
4Eh
46h
VALUE
±30±30±30 (R from G+Main data+B from G)
±30±30±30 (R from G+Main data+B from G)
1 (Standard), 2 (High), 3 (Low), 4 (User)
±2
±10
±10
±10
0-3
0-3
0 (Main), 1 (Sub)
0 (Off), 1 (Mirror), 2 (Invert), 3 (Mirror invert)
±15
0 (ON), 1 (OFF)
00 (Off) , 05, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60
0 (ON), 1 (OFF)
0 (Upper left), 1 (Lower right)
0 (ON), 1 (OFF)
0 (ON), 1 (OFF)
0 (AUTO), 1 (OFF)
0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
0(
), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais), 5 (Italiano), 6 (
)
+ (increase), – (decrease)
+ (increase), – (decrease)
00 - 31
+ (increase), – (decrease)
0 (RGB), 1 (YCBCR), 2 (YPBP R)
00 - 15
00 - 15
000 - 255
000 - 255
0 (ON), 1 (OFF)
AP – 5
APPENDIX
The menu setting commands execute the menu setting of this projector. If the personal computer doesn’t send
the commands without attaching the data code, the projector which has received the command replays the
setting data as data code.
Control this projector by using a personal computer (Continued)
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII
HEX
'+'
2Bh
[Example 1]
'–'
2Dh
'0'
30h
'1'
31h
'2'
32h
'3'
33h
'4'
34h
'5'
35h
'6'
36h
'7'
37h
'8'
38h
'9'
39h
Set the AUTO POWER ON to OFF.
Sending commands
from the PC etc.
30 30 41 50 4F 4E 30 0D
'0' '0' 'A' 'P' 'O' 'N' '0' ' '
Status code from
projector
30 30 41 50 4F 4E 30 0D
'0' '0' 'A' 'P' 'O' 'N' '0' ' '
Meaning
Command for setting the
AUTO POWER ON to ON
Command received
(Command echo back)
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and the difference
data of B from G.
[Example 2]
Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands
from the PC etc.
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '
Status code from
projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '
[Example 3]
Command for setting the
picture control
Command received
(Command echo back)
The TINT was set to +10 when the setting status was confirmed.
Sending commands
from the PC etc.
30 30 53 0D
'0' '0' 'S' ' '
Status code from
projector
30 30 53 2B 31 30 0D
'0' '0' 'S' '+' '1' '0' ' '
AP – 6
Meaning
Meaning
Command to confirm
setting of TINT
Command (setting of TINT
is +10) carried out
871D280D20
Printed in Japan