Samsung iDCS 100 Unit installation

iDCS 100
TECHNICAL MANUAL
INSTALLATION
TABLE OF CONTENTS JUNE 2002
T A B L E
O F
C O N T E N T S
INSTALLATION SECTION
PART
DESCRIPTION
PAGE
INSTALLATION WARNINGS ................................................................i-ii
1
SITE REQUIREMENTS .................................................................... 1.1
2
INSTALLATION OF BASIC KSU AND EXPANSION CABINET
3
2.1
UNPACKING AND INSPECTION ................................................... 2.1
2.2
KEY SERVICE UNIT INSTALLATION ............................................. 2.1
2.3
EXPANSION CABINET INSTALLATION ......................................... 2.1
2.4
GROUNDING ................................................................................ 2.2
2.5
MDF CABLING .............................................................................. 2.4
2.6
POWER CONNECTIONS .............................................................. 2.4
INSTALLING PRINTED CIRCUIT CARDS
3.1
iDCS MEM3 CARD ........................................................................ 3.1
3.2
iDCS MEM4 CARD ........................................................................ 3.1
3.3
2 SLI CARD .................................................................................... 3.1
3.4
SMISC1 CARD ............................................................................... 3.1
3.5
SMISC2 CARD ............................................................................... 3.2
3.6
2 X 4 DLI CARD ............................................................................. 3.2
3.7
S8DLI CARD .................................................................................. 3.2
3.8
2 X 4 SLI CARD ............................................................................. 3.2
3.9
S8SLI CARD .................................................................................. 3.2
3.10
S3TRK CARD ................................................................................. 3.2
3.11
S6TRK CARD ................................................................................. 3.3
3.12
2 E&M 4 DLI CARD ........................................................................ 3.3
3.13
S4BRI CARD .................................................................................. 3.4
3.14
iDCS TEPRI CARD ......................................................................... 3.4
3.15
SPLL DAUGHTER BOARD ............................................................ 3.6
3.16
MODEM CARD .............................................................................. 3.6
3.17
ITMC .............................................................................................. 3.6
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
4
5
6
INSTALLATION
TABLE OF CONTENTS JUNE 2002
POWER UP PROCEDURES
4.1
CONNECT POWER TO THE SYSTEM .......................................... 4.1
4.2
iDCS MEM3 CARD INDICATIONS ................................................. 4.1
4.3
iDCS MEM4 CARD INDICATIONS ................................................. 4.2
4.4
PCB VERIFICATION ...................................................................... 4.2
4.5
DEFAULT TRUNK AND STATION NUMBERING ............................ 4.2
CONNECTING TELCO CIRCUITS
5.1
SAFETY PRECAUTIONS ............................................................... 5.1
5.2
LOOP START LINES ...................................................................... 5.1
5.3
OFF PREMISE EXTENSIONS (OPX) ............................................. 5.1
5.4
E&M TIE LINES ............................................................................. 5.1
5.5
ISDN BRI LINES ............................................................................ 5.2
5.6
T1 or PRI CIRCUIT ......................................................................... 5.2
CONNECTING STATION EQUIPMENT
6.1
SAFETY PRECAUTIONS ............................................................... 6.1
6.2
KEYSETS ....................................................................................... 6.1
6.3
DCS 32 BUTTON ADD-ON MODULE ............................................ 6.1
6.4
SINGLE LINE TELEPHONE .......................................................... 6.1
6.5
DOOR PHONE AND DOOR LOCK RELEASE................................ 6.1
6.6
ISDN BRI STATIONS...................................................................... 6.2
6.7A
WALL-MOUNTING KEYSETS ........................................................ 6.2
6.7B WALL-MOUNTING KEYSETS WITH ULTRA BASE WEDGE .......... 6.3
6.7C WALL-MOUNTING iDCS KEYSETS ............................................... 6.2
6.8
64 BUTTON MODULES ................................................................. 6.3
6.9
ATTACHING DCS 32 BUTTON AOM AND DCS 64 BUTTON
MODULES TO MASTER STATION ................................................. 6.3
6.10
ATTACHING iDCS 64B MODULES
TO AN iDCS KEYSET .................................................................... 6.4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
7
8
9
10
CONNECTING OPTIONAL EQUIPMENT
7.1
MUSIC ON HOLD/BACKGROUND MUSIC .................................... 7.1
7.2
EXTERNAL PAGING ...................................................................... 7.1
7.3
COMMON BELL ............................................................................ 7.2
7.4
RING OVER PAGE ......................................................................... 7.2
7.5
STATION MESSAGE DETAIL RECORDING (SMDR)...................... 7.2
7.6
PC PROGRAMMING...................................................................... 7.3
7.7
REMOTE PROGRAMMING............................................................ 7.3
7.8
POWER FAILURE TRANSFER (PFT) ............................................. 7.3
7.9
VOICE MAIL/AUTO ATTENDANT .................................................. 7.3
7.10
CONNECTING SYSTEM BACKUP BATTERIES
TO THE iDCS 100 POWER SUPPLY .............................................. 7.4
INSTALLING KEYSET DAUGHTERBOARDS
8.1
KDB DLI ......................................................................................... 8.1
8.2
KBD SLI ......................................................................................... 8.1
8.3
CONNECTING TO THE KDBS....................................................... 8.1
CHANGING SOFTWARE
9.1
REPLACING THE EPROMS .......................................................... 9.1
9.2
SOFTWARE UPGRADE VIA iDCS PCMMC .................................... 9.1
INSTALLING CALLER ID
10.1
11
INSTALLATION
TABLE OF CONTENTS JUNE 2002
GENERAL INFORMATION .......................................................... 10.1
ADDING CARDS TO AN EXISTING SYSTEM
11.1
ADDING AN SMISC CARD .......................................................... 11.1
11.2
ADDING A 2 SLI CARD ................................................................ 11.1
11.3
ADDING AN S3TRK CARD .......................................................... 11.2
11.4
ADDING AN S6TRK CARD .......................................................... 11.2
11.5
ADDING AN S8DLI CARD ............................................................ 11.2
11.6
ADDING AN S8SLI CARD ............................................................ 11.2
11.7
ADDING A 2 X 4 CARD ................................................................ 11.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
TABLE OF CONTENTS JUNE 2002
11.8
ADDING AN S4BRI CARD ........................................................... 11.3
11.9
ADDING AN SPLL DAUGHTER BOARD...................................... 11.4
11.10 ADDING A MODEM CARD ........................................................... 11.4
12
13
INSTALLING A SVMi-8 CARD
12.1
SYSTEM SIZE WITH SVMi-8 ....................................................... 12.1
12.2
REMOVING THE COVER ............................................................ 12.1
12.3
ADDING A SECOND VOICE PROCESSING MODULE (VPM) ..... 12.1
12.4
INSERTING THE CARD ............................................................... 12.1
12.5
UPGRADING AN EXISTING CARD TO 8 PORTS ........................ 12.1
INSTALLING A SVMi-4 CARD
13.1
SYSTEM SIZE WITH A SVMi-4 CARD INSTALLED ...................... 13.1
13.2
UPGRADING THE SVMi-4 TO FOUR PORTS .............................. 13.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
WARNINGS JUNE 2002
INSTALLATION WARNINGS
1.
SAFETY PRECAUTIONS
To limit the risk of personal injury, always follow these precautions before
connecting TELCO circuits:
a. Never install telephone wiring during a lightning storm.
b. Never install telephone jacks in a wet location unless the jack is
specifically designed for wet locations.
c. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
d. Use caution when installing or modifying telephone lines.
e. Do not use this product near water, for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming
pool.
f. Do not use the telephone to report a gas leak in the vicinity of the leak.
g. Use only the power cord and batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode. Check with local codes
for possible special disposal instructions.
2.
BATTERY BACKUP-CONNECTOR CAUTION: To reduce risk of fire and
injury to persons, use only a sealed nickel cadmium or lead-acid battery
supply capable of handling a charge current of 0.4A, a abnormal charge
current of 2.0A, charge voltage of –54 V dc and d discharge rated of 40 Ah.
3.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacture’s instructions.
ATTENTION: II y a danger d’explosion s’ll y a remplacement incorrect de la
batterie. Remplacer uniquement avec une batterie du même type ou d’un
type equivalent recommandé par le constructeur. Mettre au rebut les
batteries usages confomément aux instructions du fabricant.
4.
DISCONNECT DEVICE: Disconnect Device is an Appliance Coupler.
5.
FUSE CAUTION: Double pole / neutral fusing
+
ATTENTION: Double pole / fusible sur le neuter.
For continued protection against risk of fire, replace only with same type and
rating of fuse.
Disconnect power before changing fuse.
i
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
6.
7.
!
INSTALLATION
WARNINGS JUNE 2002
a. Provided with the current limitations and maximum overcurrent
protection for telecommunication circuits.
b. Reference to the specific power supply or current limiting device
provided with the product
c. Detailed instructions showing the proper method of installation
and connections to the telecommunication wiring system.
A separate protective earthing terminal shall be provided in addition to the
main protective earthing terminal is permanently connected to earth.
ii
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 1 JUNE 2002
PART 1. SITE REQUIREMENTS
When planning the installation of the iDCS 100, choose a site that meets the following
requirements:
!
!
!
!
!
!
!
!
Select a location for the key service unit (KSU) that has enough space for easy
installation and adequate lighting (see Figure 1–1).
Select a location that will minimize cable lengths. See the Cable Requirements table
below.
The equipment should not be exposed to direct sunlight, corrosive fumes, dust,
constant vibration or strong magnetic fields such as those generated by motors and
copy machines.
A direct commercial AC power outlet is required. Do not use extension cords.
Preferably, a dedicated circuit should be used to minimize the risk of other electrical
equipment being connected that could adversely affect system operation.
Ensure that all wires and cables going to and coming from the KSU are properly
routed. Do not cross fluorescent lights or run parallel with AC wires.
The equipment must be located in an environment that will maintain a temperature
range of 32°–104°F (0°–40°C) and a humidity range of 10%–90% non-condensing.
Allow at least 6" clearance on both sides and 6" clearance on top of the KSU to
ensure proper ventilation.
Do not install in close proximity to a fire sprinkler head or other sources of water.
Meeting these requirements will help to ensure proper performance and greater life
expectancy of the system.
CABLE REQUIREMENTS
EQUIPMENT
CABLE
AWG
MAX FEET
MAX METERS
DIGITAL KEYSETS
1 PR. TWISTED
24
1300
400
ADD-ON MODULES
1 PR. TWISTED
24
1300
400
SINGLE LINE STATION
1 PR. TWISTED
24
3000
1 KM
DOOR PHONE
2 PR. TWISTED
24
330*
100
*This is the maximum distance a door phone can be from the DPIM. The DPIM can be
a maximum of 900 cable feet from the KSU.
1.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 1 JUNE 2002
14 3/8"
6.5"
iDCS
100
Digital
Communications
System
18 1/8"
KSU
Expansion
Cabinet
5 1/8"
MAIN CABINET AND
EXPANSION CABINET
UNIT DIMENSIONS
FIGURE 1–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
PART 2. INSTALLATION OF BASIC KSU AND
EXPANSION CABINET
2.1 UNPACKING AND INSPECTION
After unpacking the KSU, inspect for signs of physical damage. If any damage is
detected, do not attempt to install. Contact SAMSUNG TELECOMMUNICATIONS
AMERICA, Technical Support Department.
Check to see that the KSU carton includes the following items:
Key service unit
! Wall-mount kit consisting of 4 screws
• Vinyl bag containing cable ties and a battery cable
• Power cord
• KSU mounting template
!
Check to see that the EXPANSION CABINET carton includes the following:
!
!
Expansion cabinet
Vinyl bag with screws and ferrite choke
2.2 KEY SERVICE UNIT INSTALLATION
The key service unit (KSU) must be wall-mounted. The KSU should be mounted on a
plywood backboard at least 5/8" thick. Using the installation template or the diagram in
figure 2–1 mark the location for four mounting screws. Attach two mounting screws 12
7/8” apart horizontally to the blackboard. Next hang the KSU on the screws and secure
it to the backboard with the remaining two screws (see Figure 2–1). Tighten all four
screws to secure KSU in place.
2.3 EXPANSION CABINET INSTALLATION
1. Hang the expansion cabinet on the KSU bracket and attach it securely to the
backboard with the two screws supplied (see Figure 2–2A).
NOTE:
When you are adding an expansion cabinet to a system, please
remember to remove the cable access breakout panels BEFORE
attaching the expansion cabinet to the KSU. DO NOT cut the tabs on the
bottom of the breakout-panels as this will leave a sharp edge that can cut
into the cable. Instead bend the panel down out of the way.
2. Secure the expansion cabinet to the KSU by inserting the two short screws into the
holes on the left of the expansion cabinet (see Figure 2-2B).
WARNING:
The KSU must be turned off before proceeding. Plugging the cables
into the KSU while it is turned on can result in electric shock and/or
2.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
equipment damage. If the expansion cabinet is being added to an
existing system make sure the switch on the MEM card is turned ON
before powering down the KSU to keep the customer data intact.
3. Connect the expansion cabinet to the basic KSU by plugging free end of the ribbon
cable into the socket on the KSU motherboard (see Figure 2–3).
4. Connect the ground wire from the expansion cabinet to the screw in the top right
hand corner of the KSU motherboard (see Figure 2–4).
5. Connect the two red and green cable pairs from the expansion cabinet to the
connectors of the KSU motherboard (see Figure 2–3).
6. Install any new cards in the expansion cabinet and restore power to the system.
2.4 GROUNDING
An equipment grounding conductor that is not smaller in size than the ungrounded
branch-circuit supply conductors is to be installed as part of the circuit that supplies the
product or system. Bare, covered, or insulated grounding conductors are acceptable.
Individually covered or insulated equipment grounding conductors shall have a
continuous outer finish that is either green or green with one or more yellow stripes.
The equipment grounding conductor is to be connected to ground at the service
equipment.
The attachment-plug receptacles in the vicinity of the product or system are all to be of
a grounding type, and the equipment grounding conductors serving these receptacles
are to be connected to earth ground at the service equipment.
WARNING: HIGH LEAKAGE CURRENT! Earth connection is essential before
connecting supply.
The iDCS 100 system requires that a supplementary (see below) earth ground be
connected to the system. This is the preferred method of grounding the iDCS 100. It
has been observed that the third wire ground may be inferior or can contain noise that
may prevent the digital data bus from canceling out noise. This may result in erratic
operation of the iDCS 100. Another problem that has occurred is that some UPS battery
systems do not pass the ground through to the power cord resulting in no ground to
the system. The grounding lug on the bottom of the left side of the cabinet must be
connected to one of the following: bonded building steel, cold water pipe or a ground
rod using at least #16 AWG copper wire (see Figure 2–5). Additionally, the ground
between cabinets in a multiple cabinet system must also be at least #16 AWG copper
wire. The third wire AC ground or FG is connected to the system frame via the ground
strap from the ground connector on the AC socket.
2.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
A supplementary equipment grounding conductor shall be installed between the
system and ground that is in addition to the equipment grounding conductor in the
power supply cord.
The supplementary equipment grounding conductor shall not be smaller in size than
the ungrounded branch-circuit supply conductors. The supplementary equipment
grounding conductor shall be connected to the product at the terminal provided, and
shall be connected to ground in a manner that will retain the ground connection when
the product is unplugged from the receptacle. The connection to ground of the
supplementary equipment grounding conductor shall be in compliance with the rules
for terminating bonding jumpers in Part K of Article 250 of the National Electrical Code
ANSI/NFPA 70. Termination of the supplementary equipment grounding conductor is
permitted to be made to building steel, to a metal electrical raceway system, or to any
grounded item that is permanently and reliably connected to the electrical service
equipment ground.
Bare, covered, or insulated grounding conductors are acceptable. A covered or
insulated grounding conductor shall have a continuous outer finish that is either green
or green with one or more yellow stripes.
Failure to provide an adequate ground may cause a safety hazard, confusing trouble
symptoms or even circuit card failure.
WARNING: Unplug the power cord from the AC outlet before attempting to connect
the ground. Hazardous voltage may cause death or injury. Observe extreme caution
when working with AC power. Remove champ connectors from trunk cards.
What the above paragraphs mean is when conventional analog telephone circuits are
connected to the iDCS 100 system, under fault conditions (i.e., the tip and/or ring
conductor is crossed with a power line, or the circuit is affected by lightning during a
storm), it is possible for hazardous potentials to appear across the tip and ring wiring
coming into the iDCS 100 cabinet(s) from the outside plant (i.e., overhead cables,
buried cables, cable head pedestal). These circuits are provided with both primary and
secondary protection circuitry which will attempt to drain off these high voltages and
currents to earth ground. Obviously, it is important to have a good source of ground
connected to the iDCS 100 system to drain this energy off. Also, certain metallic analog
circuits (e.g., E & M trunks) require a current flow to earth ground to accommodate
normal operating conditions and/or to resolve fault conditions. Again, a good earth
ground source is required by the iDCS 100 system.
The iDCS 100 system has two ground reference points. One point is via the green wire
in the power cord connected to the AC power outlet. This ground connection is
provided to meet local electrical codes when the AC ground is required to be common
with the earth ground. However, this can be disconnected either intentionally or
unintentionally. Consequently, a more permanent ground connection is required by
2.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
connecting a high current/voltage capacity ground wire which is bonded to ground at
the electric service power entrance or via some other method approved by the National
Electrical Code to the iDCS 100 system ground lug. This is a more secure ground
connection, which can only be disconnected intentionally. These precautions are taken
for safety reasons to protect personnel working on the iDCS 100 system and also for
operational reasons to accommodate ground return and/or ground-referenced analog
telephone circuits, which require this solid earth ground connection for normal
functioning.
2.5 MDF CABLING
All connections to the iDCS 100 system are made by way of a customer-provided main
distribution frame (MDF). The KSU is connected to the MDF using two 25 pair male
amphenol-type cables and the expansion cabinet is connected to the MDF using a 25
pair male amphenol-type cable. These cables can be routed into the KSU cabinet from
below.
NOTE 1: The iDCS 100 requires the use of amphenol cables with MALE connectors.
NOTE 2: Before plugging the MDF cables into the KSU you must remove the cover
plate on the bottom of the KSU to allow the KSU cover to close correctly. You
may replace the cover plate to secure the cables when you have finished.
Label each cable to correspond with the connector numbers (see Figure 2–6). Label
each 66 type-terminating block with the same connector number with which the cable
is labeled.
Use one pair twisted jumper wire to cross-connect stations or lines to their associated
port.
2.6 POWER CONNECTIONS
• AC POWER CORD ASSEMBLY
The AC Power Cord Assembly plugs into the AC power socket which is located on the
left side of the cabinet. The AC connection is a standard 16 AWG computer type power
cord.
WARNING: DO NOT CONNECT AC POWER TO THE SYSTEM (see Section 4, Power
Up Procedures)
2.4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
• FUSE
CAUTION:
Double pole / neutral fusing
+
ATTENTION:
Double pole / fusible sur le neuter.
CAUTION:
1. For continued protection against risk of fire, replace only with same type and rating
of fuse.
2. DISCONNECT POWER BEFORE CHANGING FUSE.
!
The current limitations and maximum overcurrent protection for
telecommunication circuits reference to the specific power supply or
current limiting device provided with the product detailed instructions
showing the proper method of installation and connections to the
telecommunication wiring system.
• POWER SUPPLY UNIT (iDCS PWR)
The iDCS PWR is the power supply for the iDCS 100 KSU. The iDCS PWR can
accommodate a maximum of 48 keysets without an SVMi-8 and 40 keysets with an
SVMi-8. The power supply is permanently installed in the KSU, and is protected by a
metal cover. The power supply should only be removed by a qualified service
personnel.
WARNING: DO NOT CONNECT AC POWER TO THE SYSTEM (see Section 4, Power
Up Procedures)
• EXTERNAL –48VDC BATTERY SOURCE
CAUTION: To reduce risk of fire and injury to persons, use only a sealed nickel
cadmium or lead-acid battery supply capable of handling a charge current of 0.45 A,
a charge voltage of –56 VDC and a discharge rate of 45 Ah.”
The iDCS 100 provides for connection of an external battery plant (i.e. to provide
–48VDC to power the system). The iDCS PWR provides -56VDC at 0.4 amperes
charging current (i.e. when AC power is present) which allows for float charging from
the iDCS 100 to emergency backup batteries. The iDCS 100 can also run without AC
power on a –48VDC battery system or rectifier. There should be no more than a 0.5VDC drop in voltage from the iDCS 100 and the batteries. Ensure polarity prior to
connecting the external –48VDC power source to the system.
2.5
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
The -48VDC cable assembly has a male 2 pin connector on the iDCS PWR. Insert this
end of the DC cable into the battery (BATT) connector found on the iDCS PWR (see
Figure 2–7). Attach the other end of the DC power cable to the –48VDC power source.
WARNING: Be sure the proper polarity is observed. Equipment damage will result if
polarity is reversed. Do not connect external AC or DC power to the System (see
Section 4 Power Up Procedures).
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
2.6
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
12 7/8"
12"
MDF SCREWS LOCATION
KSU
FIGURE 2–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
TEPRI
UNIVERSAL SLOT 5
SVMi-8
UNIVERSAL SLOT 4
UNIVERSAL SLOT 3
UNIVERSAL SLOT 2
UNIVERSAL SLOT 1
MISC SLOT
MEM SLOT
2 SLI SLOT
WALL MOUNTING
SCREWS
WALL MOUNTING
SCREWS
KSU AND EXPANSION CABINET
WALL MOUNTING
FIGURE 2–2A
HOME
PAGE
Table of
Contents
EXPANSION CABINET
MOUNTING
UNIVERSAL SLOT 3
UNIVERSAL SLOT 2
UNIVERSAL SLOT 1
MISC SLOT
MEM SLOT
INSTALLATION
PART 2 JUNE 2002
2 SLI SLOT
iDCS 100
TECHNICAL MANUAL
EXPANSION
CABINET
ATTACHMENT
SCREWS
FIGURE 2–2B
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
UNIVERSAL SLOT 3
TEPRI
SVMi-8
UNIVERSAL SLOT 5
RIBBON
CABLE
UNIVERSAL SLOT 4
UNIVERSAL SLOT 2
UNIVERSAL SLOT 1
MISC SLOT
MEM SLOT
2 SLI SLOT
RED/GREEN
CABLE
RED/GREEN
CABLE
RIBBON CABLE AND RED/GREEN
CABLE PAIR CONNECTION
EXPANSION CABINET TO KSU
FIGURE 2–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
EXPANSION CABINET
GROUND WIRE TO KSU
TEPRI
UNIVERSAL SLOT 5
SVMi-8
UNIVERSAL SLOT 4
UNIVERSAL SLOT 3
UNIVERSAL SLOT 2
UNIVERSAL SLOT 1
MISC SLOT
MEM SLOT
2 SLI SLOT
GROUND
WIRE
FIGURE 2–4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
GROUNDING
LUG
BOTTOM VIEW
KSU GND LUG
FIGURE 2–5
HOME
PAGE
Table of
Contents
CONNECTOR DESIGNATOR
TEPRI
SVMi-8
P2
UNIVERSAL SLOT 5
UNIVERSAL SLOT 4
UNIVERSAL SLOT 3
UNIVERSAL SLOT 2
UNIVERSAL SLOT 1
MISC SLOT
MEM SLOT
2 SLI SLOT
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
P5
P1
FIGURE 2–6
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 2 JUNE 2002
RESERVE POWER
BATTERY CONNECTOR
POWER SUPPLY
BLACK
RED
CONNECT TO EITHER A OR B
+
–
12V
+
–
12V
+
–
+
12V
–
+
12V
+
–
+
6V
6V
+
–
–
+
+
–
6V
6V
+
–
–
–
6V
6V
+
–
OPTION A
+
6V
–
+
6V
–
OPTION B
BATTERIES SHOULD BE PLACED
WITHIN THREE FEET OF KSU
RESERVE POWER BATTERY
CONNECTIONS
FIGURE 2–7
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
PART 3. INSTALLING PRINTED CIRCUIT CARDS
Unpack and inspect each card before installing. Check for signs of physical damage. If
any damage is detected, do not attempt to install. Contact Samsung Technical Support
immediately.
3.1 iDCS MEM3 CARD (Figure 3–2)
Make sure that the BACK UP switch is in the OFF position. Insert the iDCS MEM3 card
in the KSU slot labeled MEM (see Figure 3–1). Push firmly in the middle of both card
ejectors on the iDCS MEM3 card to ensure that it is fully inserted into the backplane
connector.
To prevent accidental damage to the iDCS MEM3 card, the MEM connector on the
backplane is positioned to mate only with memory cards. Other interface cards will not
mate with this connector and the iDCS MEM3 card will not mate with any other
connector.
3.2 iDCS MEM4 CARD (Figure 3–3)
Make sure that the BACK UP switch is in the OFF position. Insert the iDCS MEM4 card
in the KSU slot labeled MEM (see Figure 3–1). Push firmly in the middle of both card
ejectors on the iDCS MEM4 card to ensure that it is fully inserted into the backplane
connector.
To prevent accidental damage to the iDCS MEM4 card, the MEM connector on the
backplane is positioned to mate only with memory cards. Other interface cards will not
mate with this connector and the iDCS MEM4 card will not mate with any other
connector.
3.3 2 SLI CARD (Figure 3–4)
This card has no selectable options. Insert the 2 SLI card into the appropriate slot (see
Figure 3–1). Push firmly in the middle of both card ejectors to ensure that it is fully
inserted into the back plane connector.
3.4 SMISC1 CARD (Figure 3–5)
There are no options to select on this card. Insert the SMISC1 card into the appropriate
slot (see Figure 3–1). Push firmly in the middle of both card ejectors to ensure that it is
fully inserted into the back plane connector.
NOTE: Only one SMISC1/2 card can be installed in a system.
Install the SMODEM card, if required, onto the SMISC card before installing the
SMISC card.
3.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
3.5 SMISC2 CARD (Figure 3–5)
The Auto Attendant Message Memory backup switch should be turned ON to protect
the customer-recorded messages in the event of a power failure. This can be done
before or after the card is installed, as the switch is easily accessible. Insert the SMISC2
card into the appropriate slot (see Figure 3–1). Push firmly in the middle of both card
ejectors to ensure that it is fully inserted into the back plane connector.
NOTE: Only one SMISC1/2 card can be installed in a system.
Install the SMODEM card, if required, onto the SMISC card before installing the
SMISC card.
3.6 2 X 4 DLI CARD (Figure 3–6)
This is the same card as used on the DCS Compact. There are no options to select on
this card. Insert the 2 X 4 DLI card into any universal slot in the KSU or expansion
cabinet (see Figure 3–1). Push firmly in the middle of both card ejectors on each card
to ensure that it is fully inserted into the back plane connector.
3.7 S8DLI CARD (Figure 3–6)
There are no options to select on this card. Insert the S8DLI card into any universal slot
in the KSU or expansion cabinet (see Figure 3–1). Push firmly in the middle of both
card ejectors on each card to ensure that it is fully inserted into the back plane
connector.
3.8 2 X 4 SLI CARD (Figure 3–7)
This is the same card as used on the DCS Compact. There are no options to select on
this card. Insert the 2 X 4 SLI card into any universal slot in the KSU or expansion
cabinet (see Figure 3–1). Push firmly in the middle of both card ejectors on each card
to ensure that it is fully inserted into the back plane connector.
3.9 S8SLI CARD (Figure 3–7)
There are no options to select on this card. Insert the S8SLI card into any universal slot
in the KSU or expansion cabinet (see Figure 3–1). Push firmly in the middle of both
card ejectors on each card to ensure that it is fully inserted into the back plane
connector.
3.10 S3TRK CARD (Figure 3–8)
There are no options to select on this card. Insert the S3TRK card into any universal
slot in the KSU or expansion cabinet (see Figure 3–1). Push firmly in the middle of both
card ejectors on each card to ensure that it is fully inserted into the back plane
connector.
3.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
3.11 S6TRK CARD (Figure 3–8)
There are no options to select on this card. Insert the S6TRK card into any universal
slot in the KSU or expansion cabinet (see Figure 3–1). Push firmly in the middle of both
card ejectors on each card to ensure that it is fully inserted into the back plane
connector.
3.12 2 E&M 4 DLI CARD (Figure 3–9)
This is the same card as used on the DCS Compact. The E&M trunk circuits on this
card can be set to provide either Type 1 or type 5 operation. Type 1 operation is used
when connecting to Telco circuits and type 5 is used when connecting “back to back”
across a private cable. Set the jumpers located between the two relays (see Figure 3–
9) according to the table below. Both of the jumpers for each circuit must be set to the
same type for correct operation.
CIRCUIT
JUMPER
POSITION
TYPE
1
J1
T1
TYPE 1
1
J1
T5
TYPE 5
1
J2
T1
TYPE 1
1
J2
T5
TYPE 5
2
J3
T1
TYPE 1
2
J3
T5
TYPE 5
2
J4
T1
TYPE 1
2
J4
T5
TYPE 5
WARNING: Turn the system off and remove the card from the system before
attempting to change jumper settings. 48 volts is present on the jumpers at all times
the system is turned on.
NOTE: When set to TYPE 1 the E&M Tie line circuits on this card are USOC TYPE
TL11M.
Insert the 2 E&M X 4 DLI card into any universal slot in the KSU or expansion cabinet
(see Figure 3–1). Push firmly in the middle of both card ejectors on each card to ensure
that it is fully inserted into the back plane connector
3.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
3.13 S4BRI CARD (Figure 3–10)
The S4BRI card is equipped with dip switch controlled line termination resistors. If a BRI
circuit is to be used as a Trunk circuit these switches must be in the OFF position. If a
circuit is to be used as a station then the dip switches for that circuit must be in the ON
position.
CIRCUIT
DIP SWITCH
1
SW 1
2
SW 2
3
SW 3
4
SW 4
NOTE: In order for BRI circuits to operate the system must have an SPLL board
installed in the KSU.
3.14 iDCS TEPRI CARD (Figure 3–11)
Removing the Cover
Before the iDCS TEPRI card can be installed in the iDCS 100 the card module must first
be disassembled to allow the card to fit the slot. To disassemble the iDCS TEPRI card,
first remove the ejector tabs by pulling them outward until they snap off. Next, to
separate the two halves of the casing, remove the four screws and pull the two halves
apart. This releases the iDCS TEPRI card PCB.
Installing the Card
The iDCS 100 system must be equipped with an expansion cabinet (Type-A or Type-B),
and only one iDCS TEPRI card may be installed in the system. The iDCS TEPRI
supports either T1 or ISDN PRI service. The first four LEDs on the front of the card
provide the status of the service (Sync, AIS, Loss and Layer 2 Active states). The
second four LED’s on the front of the card display the type of service. There are two
RJ45 modular jacks on the face of the card. The settings for T1 or PRI service are
selected by a bank of dip switches as defined below. The PRI supports NI1, NI2, AT&T
No. 5 ESS, and DMS 100 offices. Push firmly in the middle of the card to ensure that it
is fully inserted into the back plane connector.
Notes:
A Rev. 04 or later TEPRI card must be used.
Do not insert card with system power ON.
In order for the TEPRI circuits to operate the system must have a SPLL
board installed in the KSU.
3.4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
iDCS TEPRI CARD DIP SWITCH
Switch No.
ON
OFF
1
T1
E1
2
PRI
T1
3
NFAS (24B)
NFAS (23B + D)
4
NETWORK
USER
5
AFT
NORMAL
6
Switch 6 must be OFF
7
Switch 7 must be OFF
8
Switch 8 must be ON
iDCS TEPRI LED DEFINITIONS
LED Name
Function
Status
Normal Status
Error Status
SYN
Synchronization Loss. Indicates
wander or loss of framing.
OFF
ON
LOS
Loss of Signal. No PCM Clocking is
being received.
OFF
ON
AIS
Alarm Indicating Signal. Indicating
that all one’s are being received.
OFF
ON
L2
Layer 2 is active. PRI messaging is
being received.
OFF
ON
IPC
IPC link set up.
CLK
MODE
OFF / IPC link set up
OFF/CARD is secondary
source ON card is primary
source.
Card clock status.
LED’s TP1 & TP2 show the span type
TP1
TP2
E1 mode
OFF
OFF
E1 PRI mode
OFF
ON
T1 mode
ON
OFF
T1 PRI mode
ON
ON
3.5
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
3.15 SPLL DAUGHTER BOARD (Figure 3–12)
There are no options to select on this card. Insert the SPLL daughter board onto its
connectors in the bottom left hand corner of the KSU motherboard (see Figure 3–13).
Push firmly in the middle of both the connectors to ensure that it is fully inserted into
the back plane connector.
3.16 MODEM CARD (Figure 3–14)
There are no options to select on this card. Install the modem card onto its connectors
on the SMISC card (see Figure 3–15). Press firmly on both corners above the
connectors to ensure that it is fully inserted on to the SMISC connectors.
3.17 IP TELEPHONY MODULE (ITMC) (Figure 3–16)
There are no options to select on the ITMC card and its capacity is 8 channels. The
card has eight (8) LEDs on its faceplate to indicate the status of the card. These
indications are described below. Insert the card into any universal card slot within the
main KSU (not expansion cabinet). See Figure 3–1. Push firmly in the middle of both
card ejectors to ensure the card is firmly seated into the back plane connector.
LED Name
PWR
Function
Power State
Status
OFF Power is OFF
ON Power is ON
RUN
Processor Status
OFF Power is OFF
ON Card is booting
Flicker Normal Operation
RX
LAN TX State
TX
LAN RX State
SPD
LAN Speed
OFF 10 MBPS
ON 100 MBPS
L1
Future
L2
Future
L3
Future
3.6
HOME
PAGE
Table of
Contents
KSU AND EXPANSION
CABINET SLOT POSITIONS
TEPRI
SVMi-8
UNIVERSAL SLOT 5
UNIVERSAL SLOT 4
UNIVERSAL SLOT 3
UNIVERSAL SLOT 2
UNIVERSAL SLOT 1
MISC SLOT
MEM SLOT
INSTALLATION
PART 3 JUNE 2002
2 SLI SLOT
iDCS 100
TECHNICAL MANUAL
FIGURE 3–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
iDCS MEM3 CARD
FIGURE 3–2
iDCS MEM4 CARD
FIGURE 3–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
2 SLI CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
SMISC 1 AND 2 CARDS
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–5
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
2 X 4 DLI CARD AND S8DLI CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–6
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
2 X 4 SLI CARD AND S8SLI CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–7
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
S3TRK CARD AND S6TRK CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–8
HOME
PAGE
Table of
Contents
INSTALLATION
PART 3 JUNE 2002
FG
J2
T5
J4
RLY2
FG
48
NO
T1
48
NO
48
FG
NC
T5
48
J3
FG
T1
J1
NC
TYPE
RLY1
iDCS 100
TECHNICAL MANUAL
2 E&M / 4 DLI CARD
FIGURE 3–9
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
S4BRI CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–10
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
iDCS TEPRI CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–11
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
SPLL DAUGHTER BOARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–12
HOME
PAGE
Table of
Contents
UNIVERSAL SLOT 3
UNIVERSAL SLOT 1
UNIVERSAL SLOT 2
MISC SLOT
MEM SLOT
INSTALLATION
PART 3 JUNE 2002
2 SLI SLOT
iDCS 100
TECHNICAL MANUAL
SPLL
DAUGHTER
BOARD
SPLL INSTALLATION ON
KSU MOTHERBOARD
FIGURE 3–13
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
MODEM CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–14
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 3 JUNE 2002
MODEM CARD
SMISC 1 OR 2 CARD
MODEM CARD INSTALLATION ON
SMISC CARD
FIGURE 3–15
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
ITMC CARD
INSTALLATION
PART 3 JUNE 2002
FIGURE 3–16
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 4 JUNE 2002
PART 4. POWER UP PROCEDURES
4.1 CONNECT POWER TO THE SYSTEM
Verify that the AC voltage at the dedicated electrical outlet is in the range of 82–132
Volts AC. Make sure the AC power switch on the system power supply is in the OFF
position and that the SMEM card battery switch is also in the OFF position. Plug the
KSU power cord into the dedicated polarized AC outlet. Turn the AC power switch to
the ON position. The LED’s on the power supply will light steady to confirm the
presence of power. If both PSU LEDs fail to illuminate, unplug the system, remove the
power supply cover and check the AC fuses located on the left-hand side of the face of
the PSU.
If the AC fuses are good but the AC LED does not illuminate, unplug the KSU and
change power supplies. This in all probability will solve the problem. If it does not,
contact Samsung Technical Support.
If the AC LED is illuminated but the DC LED is out you must correct the problem before
continuing. Turn off the power switch and check the DC fuses located in the opening of
the face of the PSU. If the DC fuses are good but the DC LED does not illuminate,
unplug the PSU from the motherboard. Turn the system on. Check the LEDs again. If
the problem is corrected, you have a defective KSU motherboard or card. Test and
remove the faulty card before continuing. If this does not correct the problem, unplug
the KSU and change power supplies. This in all probability will solve the problem. If it
does not, contact Samsung Technical Support.
4.2 iDCS MEM3 CARD INDICATIONS
Having verified proper operation of the power supply, visually check the iDCS MEM3
card indications. The LED should flicker rapidly indicating the main processor is
functioning. The battery switch should now be turned ON. If the LED remains lit steady
turn power to the system OFF remove the iDCS MEM3 card and check the installation
of the EPROM’s by removing them and checking for bent or damaged pins. If the
EPROMs appear to be installed correctly and the system does not come up when
turned on, contact Samsung Technical Support.
The system is equipped with a halt program. When this program is running, the LED is
ON steady. The system must be reset to release the halt program and restore the
system to normal operation (see MMC 810 for operation of the halt program).
4.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 4 JUNE 2002
4.3 iDCS MEM4 CARD INDICATIONS
Having verified proper operation of the power supply, visually check the iDCS MEM4
card indications. The LED indications are as follow:
LED
Indication
OFF
ON
1
Indicates whether the status of LAN transmit chip Abnormal
(LST972, U13) is in normal or abnormal.
status
Normal
status
2
Indicates LAN link status
Link
No Link
3
Indicates whether there is LAN RX data or not
None
Exist
LED
4
Indication
Slow Flicker Fast Flicker
(500ms)
(200 ms)
RUN LED for MCP(MP)
Indicates the operation of MCP
5
RUN LED for LAN
Indicates the operation of LAN
Normal
operation
Booting
operation
Normal
operation
Booting
operation
4.4 PCB VERIFICATION
Before connecting all MDF cabling, plug in a test cable to the first S8DLI port. Connect
a display set and verify that it is working. Use maintenance programs MMC 727 and
MMC 806 to verify the system version, software version and that all cards are
recognized by the CPU. Remove the test cable and plug in all amphenol-type cables to
the MDF. Proceed with the rest of the installation.
4.5 DEFAULT TRUNK AND STATION NUMBERING
Upon initial power up, the CPU reads each slot for the existence of a card and identifies
the type of card. It stores this as the default configuration.
The system assigns trunk numbers beginning with 701 and continues to 703 if one
S3TRK card has been installed or 706 if two S3TRK cards and so on.
Station numbers are assigned in the same manner. The lowest station is assigned
station number 201 and continues to 208 for a basic KSU or to 216 for system with one
S8DLI. Keyset daughter boards are assigned numbers beginning with 301 and
continue to 308. Default data assigns the keyset in the lowest port to the operator
group and all trunks ring that station until the default is changed.
Station and trunk numbers can be changed, rearranged and reassigned, as needed
using MMC 724.
4.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
PART 5. CONNECTING TELCO CIRCUITS
5.1 SAFETY PRECAUTIONS
To limit the risk of personal injury, always follow these precautions before connecting
TELCO circuits:
a. Never install telephone wiring during a lightning storm.
b. Never install telephone jacks in a wet location unless the jack is specifically
designed for wet locations.
c. Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface.
d. Use caution when installing or modifying telephone lines.
h. Do not use this product near water, for example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
i. Do not use the telephone to report a gas leak in the vicinity of the leak.
j. Use only the power cord and batteries indicated in this manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for possible special
disposal instructions.
5.2 LOOP START LINES
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect each loop
start C.O. line to the trunk port of your choice (see Figures 5–1, 5–2, 5–3).
5.3 OFF PREMISE EXTENSIONS (OPX)
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect any 2 SLI
port to telephone company OPX circuits (see Figure 5–4).
Circuits on the 2 SLI card are specifically designed to meet TELCO requirements for
OPX use. These circuits are provided with the same over voltage and over current
protection as C.O. line circuits. Using single line stations on a 2 X 4 SLI, S8SLI or KDb
SLI may cause damage to your equipment.
There is no special programming required for OPX use; however, it is suggested that
the OPX ports be set programmed as “data ring” in MMC 208 to provide a disconnect
signal to the OPX equipment. The telephone company service facility interface code for
this type of OPX circuit is OL13C.
5.4 E&M TIE LINES
Using two pair twisted #24 AWG or #26 AWG jumper wire, cross-connect any E&M
port to a telephone company E&M circuit (see Figure 5–5). The telephone company
5.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
service facility interface code for the E&M tie line is TL11M. This is a 2 wire Type 1 tie
line.
NOTE: When connecting an E&M tie line in “back to back” fashion you must
remember to reverse the E&M leads at one end ONLY i.e. connect the E lead
on one system to the M lead of the other system and vice versa.
5.5 ISDN BRI LINES
The iDCS 100 requires that an NT1 be connected between the iDCS 100 and the BRI
circuit provided by the Telephone Company. This is necessary to convert the circuit
from the U type 2 wire interface provided by the Telephone Company to an S/T type 4
wire interface used by the iDCS 100.
Using two pair twisted #24 AWG or #26 AWG jumper wires cross-connect any S4BRI
port to the output or CPE side of the NT1 (see Figure 5–6).
For information regarding the ordering and programming of a BRI circuit please see the
Special Applications part of the Programming section of this manual.
5.6 T1 or PRI CIRCUIT
Using a standard, straight through eight conductor data cable or straight through eight
conductor line cord to connect the customer provided Channel Service Unit (CSU) to
the TEPRI card as shown in Figure 5–7.
NOTES:
1. It may be necessary to cut off the CSU end of the cable and attach a different
connector to match that of the CSU. If possible, this connection should be soldered
because good connections are critical.
2. It is recommended that the CSU be connected to the network interface with a cable
supplied by the CSU manufacturer. If this is not possible or practical, a custom
cable has to be made up. This cable should be made from 22 gauge two pair cable
with each pair individually shielded. It is recommended that the connections on this
cable be soldered wherever possible to ensure good connections. The shielding of
the cable should be connected to ground at the CSU end only to prevent a ground
loop.
3. See section 3.14 to ensure dip switch settings on the card are correct.
ORDERING A T1
The following information may be useful when ordering T1 service from the telephone
company.
5.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
PARAMETER
OPTIONS IN iDCS 100
Framing type
Super Frame (SF) or D4
Extended Super Frame (ESF)
AMI or B8ZS
Coding type
The coding type must be set up in the system to match the T1 span and is contained in
MMC 808.
5.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
CIRCUIT
TERM
COLOR
PIN
C.O. TIP
C.O. RING
FUNCTION
SLOT 1
TRUNK 1
1
2
W-BL
BL-W
26
1
C.O. TIP
C.O. RING
SLOT 1
TRUNK 2
3
4
W-0
0-W
27
2
C.O. TIP
C.O. RING
SLOT 1
TRUNK 3
5
6
W-GN
GN-W
28
3
7
8
W-BR
BR-W
29
4
PFT1 TIP
PFT1 RING
SLOT 1
TRUNK 1
9
10
W-SL
SL-W
30
5
PFT2 TIP
PFT2 RING
SLOT 1
TRUNK 2
11
12
R-BL
BL-R
31
6
13
14
R-O
O-R
32
7
15
16
R-GR
GR-R
33
8
TELCO PROVIDED
NETWORK ACCESS JACK
RJ 11C
RJ 14C
RJ 21X
CONNECT TO ANY C.O. CIRCUIT
FROM ANY S3TRK CARD
C.O. TIP
C.O. RING
SLOT 2
TRUNK 1
17
18
R-BR
BR-R
34
9
C.O. TIP
C.O. RING
SLOT 2
TRUNK 2
19
20
R-SL
SL-R
35
10
C.O. TIP
C.O. RING
SLOT 2
TRUNK 3
21
22
BK-BL
BL-BK
36
11
23
24
BK-O
O-BK
37
12
PFT1 TIP
PFT1 RING
SLOT 2
TRUNK 1
25
26
BK-GN
GN-BK
38
13
PFT2 TIP
PFT2 RING
SLOT 2
TRUNK 2
27
28
BK-BR
BR-BK
39
14
29
30
BK-S
S-BK
40
15
31
32
Y-BL
BL-Y
41
16
C.O. TIP
C.O. RING
SLOT 3
TRUNK 1
33
34
Y-O
O-Y
42
17
C.O. TIP
C.O. RING
SLOT 3
TRUNK 2
35
36
Y-G
G-Y
43
18
C.O. TIP
C.O. RING
SLOT 3
TRUNK 3
37
38
Y-BN
BN-Y
44
19
39
40
Y-S
S-Y
45
20
PFT1 TIP
PFT1 RING
SLOT 3
TRUNK 1
41
42
V-BL
BL-V
46
21
PFT2 TIP
PFT2 RING
SLOT 3
TRUNK 2
43
44
V-O
O-V
47
22
MDF CONNECTIONS
LOOP START LINE TO S3TRK CARD
FIGURE 5–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
CIRCUIT
TERM
COLOR
PIN
C.O. TIP
C.O. RING
FUNCTION
SLOT 1
TRUNK 1
1
2
W-BL
BL-W
26
1
C.O. TIP
C.O. RING
SLOT 1
TRUNK 2
3
4
W-0
0-W
27
2
C.O. TIP
C.O. RING
SLOT 1
TRUNK 3
5
6
W-GN
GN-W
28
3
C.O. TIP
C.O. RING
SLOT 1
TRUNK 4
7
8
W-BR
BR-W
29
4
C.O. TIP
C.O. RING
SLOT 1
TRUNK 5
9
10
W-SL
SL-W
30
5
C.O. TIP
C.O. RING
SLOT 1
TRUNK 6
11
12
R-BL
BL-R
31
6
13
14
R-O
O-R
32
7
15
16
R-GR
GR-R
33
8
TELCO PROVIDED
NETWORK ACCESS JACK
RJ 11C
RJ 14C
RJ 21X
CONNECT TO ANY C.O. CIRCUIT
FROM ANY S6TRK CARD
C.O. TIP
C.O. RING
SLOT 2
TRUNK 1
17
18
R-BR
BR-R
34
9
C.O. TIP
C.O. RING
SLOT 2
TRUNK 2
19
20
R-SL
SL-R
35
10
C.O. TIP
C.O. RING
SLOT 2
TRUNK 3
21
22
BK-BL
BL-BK
36
11
C.O. TIP
C.O. RING
SLOT 2
TRUNK 4
23
24
BK-O
O-BK
37
12
C.O. TIP
C.O. RING
SLOT 2
TRUNK 5
25
26
BK-GN
GN-BK
38
13
C.O. TIP
C.O. RING
SLOT 2
TRUNK 6
27
28
BK-BR
BR-BK
39
14
29
30
BK-S
S-BK
40
15
31
32
Y-BL
BL-Y
41
16
C.O. TIP
C.O. RING
SLOT 3
TRUNK 1
33
34
Y-O
O-Y
42
17
C.O. TIP
C.O. RING
SLOT 3
TRUNK 2
35
36
Y-G
G-Y
43
18
C.O. TIP
C.O. RING
SLOT 3
TRUNK 3
37
38
Y-BN
BN-Y
44
19
C.O. TIP
C.O. RING
SLOT 3
TRUNK 4
39
40
Y-S
S-Y
45
20
C.O. TIP
C.O. RING
SLOT 3
TRUNK 5
41
42
V-BL
BL-V
46
21
C.O. TIP
C.O. RING
SLOT 3
TRUNK 6
43
44
V-O
O-V
47
22
MDF CONNECTIONS
LOOP START LINE TO S6TRK CARD
FIGURE 5–2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
FUNCTION
C.O. TIP
C.O. RING
C.O. TIP
C.O. RING
CIRCUIT
TERM
COLOR
PIN
SLOT 1
TRUNK 1
1
2
W-BL
BL-W
26
1
3
4
W-0
0-W
27
2
5
6
W-GN
GN-W
28
3
7
8
W-BR
BR-W
29
4
9
10
W-SL
SL-W
30
5
11
12
R-BL
BL-R
31
6
13
14
R-O
O-R
32
7
15
16
R-GR
GR-R
33
8
17
18
R-BR
BR-R
34
9
19
20
R-SL
SL-R
35
10
21
22
BK-BL
BL-BK
36
11
23
24
BK-O
O-BK
37
12
25
26
BK-GN
GN-BK
38
13
27
28
BK-BR
BR-BK
39
14
29
30
BK-S
S-BK
40
15
31
32
Y-BL
BL-Y
41
16
33
34
Y-O
O-Y
42
17
35
36
Y-G
G-Y
43
18
37
38
Y-BN
BN-Y
44
19
SLOT 1
TRUNK 2
TELCO PROVIDED
NETWORK ACCESS JACK
RJ 11C
RJ 14C
RJ 21X
C.O. TIP
C.O. RING
C.O. TIP
C.O. RING
CONNECT TO ANY C.O. CIRCUIT
FROM ANY 2 X 4 DLI OR 2 X 4 SLI
CARD
C.O. TIP
C.O. RING
C.O. TIP
C.O. RING
MDF CONNECTIONS
LOOP START LINE TO 2 x 4 CARD
SLOT 2
TRUNK 1
SLOT 2
TRUNK 2
SLOT 3
TRUNK 1
SLOT 3
TRUNK 2
FIGURE 5–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
25 PAIR CABLE WITH CONNECTOR TO KSU P1
FUNCTION
SLT TIP
SLT RING
SLT TIP
SLT RING
CIRCUIT
1
2
TERM
COLOR
PIN
19
R-SL
10
20
SL-R
35
21
BK-BL
11
22
BL-BK
36
TELCO-PROVIDED
NETWORK ACCESS JACK
RJ 11C
RJ 14C
RJ 21X
CONNECT TO ANY CIRCUIT ON
THE 2 SLI CARD.
MDF CONNECTIONS
OFF PREMISE EXTENSION FROM
2 SLI CARD
FIGURE 5–4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
FUNCTION
CIRCUIT
TERM
COLOR
PIN
C.O. TIP
C.O. RING
M
E
SLOT 1
TRUNK 1
1
2
3
4
W-BL
BL-W
W-0
0-W
26
1
27
2
C.O. TIP
C.O. RING
M
E
SLOT 1
TRUNK 2
5
6
7
8
W-GN
GN-W
W-BR
BR-W
28
3
29
4
9
10
W-SL
SL-W
30
5
11
12
R-BL
BL-R
31
6
13
14
R-O
O-R
32
7
15
16
R-GR
GR-R
33
8
TELCO PROVIDED
NETWORK ACCESS JACK
RJ 2GX
CONNECT TO ANY E&M CIRCUIT
FROM ANY 2E&M 4 DLI.
MDF CONNECTIONS
E&M LINE TO 2EXM 4 DLI CARD
C.O. TIP
C.O. RING
M
E
SLOT 2
TRUNK 1
17
18
19
20
R-BR
BR-R
R-SL
SL-R
34
9
35
10
C.O. TIP
C.O. RING
M
E
SLOT 2
TRUNK 2
21
22
23
24
BK-BL
BL-BK
BK-O
O-BK
36
11
37
12
25
26
BK-GN
GN-BK
38
13
27
28
BK-BR
BR-BK
39
14
29
30
BK-S
S-BK
40
15
31
32
Y-BL
BL-Y
41
16
C.O. TIP
C.O. RING
M
E
SLOT 3
TRUNK 1
33
34
35
36
Y-O
O-Y
Y-G
G-Y
42
17
43
18
C.O. TIP
C.O. RING
M
E
SLOT 3
TRUNK 2
37
38
39
40
Y-BN
BN-Y
Y-S
S-Y
44
19
45
20
FIGURE 5–5
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
NT1
S/T
U
POWER
TO
TELCO
BRI
CONNECT TO ISDN NT1
MDF CONNECTIONS
FOR ISDN NT1 TO S4BRI CARD
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
27
2
W-BL
BL-W
W-0
0-W
1
2
3
4
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 1 RECEIVE A
RECEIVE B
28
3
29
4
W-GN
GN-W
W-BR
BR-W
5
6
7
8
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 2 RECEIVE A
RECEIVE B
30
5
31
6
W-SL
SL-W
R-BL
BL-R
9
10
11
12
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 3 RECEIVE A
RECEIVE B
32
7
33
8
R-O
O-R
R-GR
GR-R
13
14
15
16
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 4 RECEIVE A
RECEIVE B
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R-BR
BR-R
R-SL
SL-R
BK-BL
BL-BK
BK-O
O-BK
BK-GN
GN-BK
BK-BR
BR-BK
BK-S
S-BK
Y-BL
BL-Y
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SLOT 2
CIRCUIT
1-4
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
Y-O
O-Y
Y-G
G-Y
Y-BN
BN-Y
Y-S
S-Y
V-BL
BL-V
V-O
O-V
V-G
G-V
V-BN
BN-V
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
SLOT 3
CIRCUIT
1-4
50
25
V-S
S-V
49
50
FIGURE 5–6
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 5 JUNE 2002
TRANSMIT
PAIR
8
7
6
5
4
3
2
1
T
E
P
R
I
RECEIVE PAIR
CUSTOMER
PROVIDED
MALE RJ 45
ENDED CABLE
SYN
AIS
IPC
TPI
LOS
L2
CLK
TP2
T1
E1
CUSTOMER-PROVIDED
CUSTOMER SERVICE
UNIT
SIO
RST
TELCO T1 SPAN
MDF CONNECTIONS
T1/PRI CIRCUIT TO TEPRI CARD
FIGURE 5–7
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
PART 6. CONNECTING STATION EQUIPMENT
6.1 SAFETY PRECAUTIONS
To limit the risk of personal injury, always follow these precautions before connecting
telephone circuits:
a. Never install telephone wiring during a lightning storm.
b. Never install telephone jacks in a wet location unless the jack is specifically
designed for wet locations.
c. Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface.
d. Use caution when installing or modifying telephone lines.
6.2 KEYSETS
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect each keyset
to the DLI port of your choice (see Figures 6–1, 6–2, and 6-3).
NOTE: Because the iDCS 100 is a self-configuring system, if you connect a 12 button
keyset to a DLI port that previously had a 24 button keyset installed, the
existing data will be rewritten with 12 button keyset default data (see MMC
723).
6.3 DCS 32 BUTTON ADD-ON MODULE
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect each add-on
module (AOM) to the DLI port of your choice (see Figures 6–4, 6-5, and 6-6).
If an AOM is to operate as a stand-alone unit, there is nothing else required other than
assigning keys. When an AOM is to be used with a station, it must be assigned in MMC
209. Add-on modules can be assigned to any keyset.
6.4 SINGLE LINE TELEPHONE
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect each single
line telephone to the SLI port of your choice (see Figures 6–7, 6–8, and 6-9).
6.5 DOOR PHONE AND DOOR LOCK RELEASE
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect each DPIM
to the DLI port of your choice (see Figures 6–10, 6-11, and 6–12). Next, connect the
DPIM to the door phone using #24 AWG or #26 AWG twisted pair wire.
6.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
When a customer-provided electric door release is installed, cross-connect the
corresponding door release contacts on the DPIM to the door lock mechanism (see
Figures 6–10, 6-11 and 6–12). Use MMC 501 to program the duration of the contact
closure as required. See the user guides for door lock release operation. The door
release contacts on the DPIM are to be used for low voltage relay control only. The
contacts are rated at 24 VDC-1 amp.
WARNING: Do not attempt to connect commercial AC power to these contacts.
6.6 ISDN BRI STATIONS
The iDCS 100 uses an S/T type interface so if the BRI station equipment requires a U
type circuit then an NT1 must be connected between the iDCS 100 and the station
equipment. This will convert the circuit from the S/T type 4 wire interface provided by
the iDCS 100 to the U type 2 wire interface required by the station equipment. In this
case the maximum distance of the BRI station equipment from the iDCS 100 is
determined by the specifications of the NT1.
Using two pair twisted #24 AWG or #26 AWG jumper wire cross-connect any BRI port
to the BRI station equipment (or NT1), (see Figure 6-13).
For information regarding the programming of a BRI circuit please see the Special
Applications part of the Programming section of this manual.
6.7A WALL-MOUNTING KEYSETS
DCS keysets come equipped with a reversible base wedge. To wall-mount a keyset,
remove the wedge from the keyset and remove the directory tray from the wedge.
Mount the wedge to the wall using one of the methods below (see Figure 6-14).
Use screw holes 1 and 2 to attach the base wedge to a standard electrical outlet box.
OR
Use screw holes 1 and 3 to attach to a standard telephone wall-mount plate with
locking pins. This method can cause the keyset to wobble as the keyset feet do not fit
securely to the mounting surface.
OR
Use screw holes 4 and 5 if you are mounting on dry wall with a hole in the middle for
cable access.
6.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
6.7B WALL-MOUNTING KEYSETS WITH ULTRA BASE
WEDGE
DCS keysets now come equipped with a new Ultra Base wedge. These base wedges
are reversible and can be used for wall-mounting however not every wall mounting
scenario is appropriate. First and foremost there is only one keyhole in the center of the
base attaching to the wall, and these base wedges can not be used with the standard
wall mount bracket with the two button/pins. To wall-mount the keyset using Ultra Base
wedges use screw holes 1, 2 and 3 to mount the base wedge on dry wall with the hole
in the middle for cable access (see Figure 6-15).
6.7C WALL-MOUNTING iDCS KEYSETS
The iDCS keysets come equipped with a reversible base wedge. To wall-mount a
keyset, remove the wedge from the keyset and mount the wedge to the wall using one
of the methods below (see Figure 6-16).
Use screw holes 1 and 2 to attach the base wedge to a standard electrical outlet box.
OR
Use screw holes 1 and 3 to attach to a standard telephone wall-mount plate with
locking pins. This method can cause the keyset to wobble as the keyset feet do not fit
securely to the mounting surface.
6.8 64 BUTTON MODULES
Using one pair twisted #24 AWG or #26 AWG jumper wire, cross-connect each 64
button module (64 BM) to the DLI port or plug into the DLI daughter board or your
choice (see part 8 of the installation section). The 64 BM module can be assigned to
any keyset telephone. It must be assigned to that station in MMC 309. A maximum of
four (4) 64 button modules can be programmed in the iDCS 100 system. A maximum of
two (2) 64 button modules per keyset.
6.9 ATTACHING DCS 32 BUTTON AOM AND DCS 64
BUTTON MODULES TO MASTER STATION
These new Ultra Base Wedges allow a connector clip (packaged with 64B Modules and
AOMs) to be connected to the underside of the new style wedge and attach AOM(s) or
64B module(s) together with the main or “master” station. This “clip” allows multiple
64B modules and or AOMs to be secured or “chained” together to the main or “master”
station they are associated with. This will make instruments associated with each other
seem as one unit (see Figure 6-17, 6-18 and 6-19).
6.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
6.10 ATTACHING iDCS 64B MODULES TO AN iDCS
KEYSET
First remove the base wedge from the iDCS 64B Module and attach the bracket to it
with two of the screws provided (see Figure 6-20).
Remove the base wedge of the keyset and place it to the right of the 64 Button Module
and attach the bracket/64BM to the keyset with the remaining two screws.
The base wedge can now be replaced.
NOTE: If you wish to attach two 64 button modules to a keyset, connect the 64 button
modules together first and then attach them to the keyset.
6.4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
1
DLI TIP
DLI RING
27
2
W-0
0-W
3
4
2
DLI TIP
DLI RING
28
3
W-GN
GN-W
5
6
3
DLI TIP
DLI RING
29
4
W-BR
BR-W
7
8
4
DLI TIP
DLI RING
30
5
W-S
S-W
9
10
5
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
6
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
7
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
8
DLI TIP
DLI RING
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
DIGITAL KEYSET
SCROLL
CONNECT TO ANY DLI
ON KSU P1.
CIRCUIT
VOL
SPK
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
ANS/
RLS
MDF CONNECTIONS
DIGITAL KEYSET TO KSU P1
1
0OPER
FIGURE 6–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
SLOT 1
CIRCUIT 1
DLI TIP
DLI RING
27
2
W-O
O-W
3
4
SLOT 1
CIRCUIT 2
DLI TIP
DLI RING
28
3
W-GN
GN-W
5
6
SLOT 1
CIRCUIT 3
DLI TIP
DLI RING
29
4
W-BR
BR-W
7
8
SLOT 1
CIRCUIT 4
DLI TIP
DLI RING
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 5
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 7
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 8
DLI TIP
DLI RING
34
9
R-BN
BN-R
17
18
SLOT 2
CIRCUIT 1
DLI TIP
DLI RING
35
10
R-S
S-R
19
20
SLOT 2
CIRCUIT 2
DLI TIP
DLI RING
36
11
BK-BL
BL-BK
21
22
DLI TIP
DLI RING
37
12
BK-O
0-BK
23
24
DLI TIP
DLI RING
38
13
BK-G
G-BK
25
26
DLI TIP
DLI RING
39
14
BK-BN
BN-BK
27
28
DLI TIP
DLI RING
40
15
BK-S
S-BK
29
30
DLI TIP
DLI RING
41
16
Y-BL
BL-Y
31
32
DLI TIP
DLI RING
42
17
Y-O
O-Y
33
34
SLOT 3
CIRCUIT 1
DLI TIP
DLI RING
43
18
Y-G
G-Y
35
36
SLOT 3
CIRCUIT 2
DLI TIP
DLI RING
44
19
Y-BN
BN-Y
37
38
DLI TIP
DLI RING
45
20
Y-S
S-Y
39
40
DLI TIP
DLI RING
46
21
V-BL
BL-V
41
42
DLI TIP
DLI RING
47
22
V-O
O-V
43
44
DLI TIP
DLI RING
48
23
V-G
G-V
45
46
DLI TIP
DLI RING
49
24
V-BN
BN-V
47
48
DLI TIP
DLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
DIGITAL KEYSET
SCROLL
VOL
SPK
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
CONNECT TO ANY DLI CIRCUIT ON
AN S8DLI CARD.
MDF CONNECTIONS
DIGITAL KEYSET TO S8DLI CARD
ANS/
RLS
0OPER
FIGURE 6–2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
26
1
W-BL
BL-W
1
2
CIRCUIT
FUNCTION
27
2
W-O
O-W
3
4
28
3
W-GN
GN-W
5
6
29
4
W-BR
BR-W
7
8
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 3
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 4
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 5
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
34
9
R-BN
BN-R
17
18
35
10
R-S
S-R
19
20
36
11
BK-BL
BL-BK
21
22
37
12
BK-O
0-BK
23
24
38
13
BK-G
G-BK
25
26
SLOT 2
CIRCUIT 3
DLI TIP
DLI RING
39
14
BK-BN
BN-BK
27
28
SLOT 2
CIRCUIT 4
DLI TIP
DLI RING
40
15
BK-S
S-BK
29
30
SLOT 2
CIRCUIT 5
DLI TIP
DLI RING
41
16
Y-BL
BL-Y
31
32
SLOT 2
CIRCUIT 6
DLI TIP
DLI RING
42
17
Y-O
O-Y
33
34
43
18
Y-G
G-Y
35
36
44
19
Y-BN
BN-Y
37
38
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
SLOT 3
CIRCUIT 3
DLI TIP
DLI RING
47
22
V-O
O-V
43
44
SLOT 3
CIRCUIT 4
DLI TIP
DLI RING
48
23
V-G
G-V
45
46
SLOT 3
CIRCUIT 5
DLI TIP
DLI RING
49
24
V-BN
BN-V
47
48
SLOT 3
CIRCUIT 6
DLI TIP
DLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
DIGITAL KEYSET
SCROLL
VOL
SPK
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
CONNECT TO ANY DLI CIRCUIT ON
A 2 X 4 CARD.
MDF CONNECTIONS
DIGITAL KEYSET TO 2 X 4 CARD
ANS/
RLS
0OPER
FIGURE 6–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
1
DLI TIP
DLI RING
27
2
W-0
0-W
3
4
2
DLI TIP
DLI RING
28
3
W-GN
GN-W
5
6
3
DLI TIP
DLI RING
29
4
W-BR
BR-W
7
8
4
DLI TIP
DLI RING
30
5
W-S
S-W
9
10
5
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
6
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
7
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
8
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
DLI TIP
DLI RING
ADD-ON MODULE
CONNECT TO ANY DLI
ON KSU P1.
CIRCUIT
VOL
MDF CONNECTIONS
AOM TO KSU P1
MUTE
SPK
FIGURE 6–4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
SLOT 1
CIRCUIT 1
DLI TIP
DLI RING
27
2
W-O
O-W
3
4
SLOT 1
CIRCUIT 2
DLI TIP
DLI RING
28
3
W-GN
GN-W
5
6
SLOT 1
CIRCUIT 3
DLI TIP
DLI RING
29
4
W-BR
BR-W
7
8
SLOT 1
CIRCUIT 4
DLI TIP
DLI RING
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 5
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 7
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 8
DLI TIP
DLI RING
34
9
R-BN
BN-R
17
18
SLOT 2
CIRCUIT 1
DLI TIP
DLI RING
35
10
R-S
S-R
19
20
SLOT 2
CIRCUIT 2
DLI TIP
DLI RING
36
11
BK-BL
BL-BK
21
22
DLI TIP
DLI RING
37
12
BK-O
0-BK
23
24
DLI TIP
DLI RING
38
13
BK-G
G-BK
25
26
DLI TIP
DLI RING
39
14
BK-BN
BN-BK
27
28
DLI TIP
DLI RING
40
15
BK-S
S-BK
29
30
DLI TIP
DLI RING
41
16
Y-BL
BL-Y
31
32
DLI TIP
DLI RING
42
17
Y-O
O-Y
33
34
SLOT 3
CIRCUIT 1
DLI TIP
DLI RING
43
18
Y-G
G-Y
35
36
SLOT 3
CIRCUIT 2
DLI TIP
DLI RING
44
19
Y-BN
BN-Y
37
38
DLI TIP
DLI RING
45
20
Y-S
S-Y
39
40
DLI TIP
DLI RING
46
21
V-BL
BL-V
41
42
DLI TIP
DLI RING
47
22
V-O
O-V
43
44
DLI TIP
DLI RING
48
23
V-G
G-V
45
46
DLI TIP
DLI RING
49
24
V-BN
BN-V
47
48
DLI TIP
DLI RING
50
25
V-S
S-V
49
50
CONNECT TO ANY DLI CIRCUIT ON
AN S8DLI CARD.
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
VOL
2
3
MUTE
4
5
6
SPK
ADD-ON MODULE
MDF CONNECTIONS
AOM TO S8DLI CARD
FIGURE 6–5
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
26
1
W-BL
BL-W
1
2
CIRCUIT
FUNCTION
27
2
W-O
O-W
3
4
28
3
W-GN
GN-W
5
6
29
4
W-BR
BR-W
7
8
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 3
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 4
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 5
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
34
9
R-BN
BN-R
17
18
35
10
R-S
S-R
19
20
36
11
BK-BL
BL-BK
21
22
37
12
BK-O
0-BK
23
24
38
13
BK-G
G-BK
25
26
SLOT 2
CIRCUIT 3
DLI TIP
DLI RING
39
14
BK-BN
BN-BK
27
28
SLOT 2
CIRCUIT 4
DLI TIP
DLI RING
40
15
BK-S
S-BK
29
30
SLOT 2
CIRCUIT 5
DLI TIP
DLI RING
41
16
Y-BL
BL-Y
31
32
SLOT 2
CIRCUIT 6
DLI TIP
DLI RING
42
17
Y-O
O-Y
33
34
43
18
Y-G
G-Y
35
36
44
19
Y-BN
BN-Y
37
38
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
SLOT 3
CIRCUIT 3
DLI TIP
DLI RING
47
22
V-O
O-V
43
44
SLOT 3
CIRCUIT 4
DLI TIP
DLI RING
48
23
V-G
G-V
45
46
SLOT 3
CIRCUIT 5
DLI TIP
DLI RING
49
24
V-BN
BN-V
47
48
SLOT 3
CIRCUIT 6
DLI TIP
DLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
ADD-ON MODULE
CONNECT TO ANY DLI CIRCUIT ON
A 2 X 4 CARD.
MDF CONNECTIONS
AOM TO 2 X 4 CARD
VOL
MUTE
SPK
FIGURE 6–6
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
TERM CIRCUIT
PIN
COLOR
10
R-SL
19
35
SL-R
20
11
BK-BL
21
36
BL-BK
22
1
2
FUNCTION
SLT TIP
SLT RING
SLT TIP
SLT RING
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
CONNECT TO ANY CIRCUIT ON
THE 2 SLI CARD.
SINGLE LINE TELEPHONE
MDF CONNECTIONS
SINGLE LINE TELEPHONE
TO 2 SLI CARD
FIGURE 6–7
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
SLOT 1
CIRCUIT 1
SLI TIP
SLI RING
27
2
W-O
O-W
3
4
SLOT 1
CIRCUIT 2
SLI TIP
SLI RING
28
3
W-GN
GN-W
5
6
SLOT 1
CIRCUIT 3
SLI TIP
SLI RING
29
4
W-BR
BR-W
7
8
SLOT 1
CIRCUIT 4
SLI TIP
SLI RING
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 5
SLI TIP
SLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 6
SLI TIP
SLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 7
SLI TIP
SLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 8
SLI TIP
SLI RING
34
9
R-BN
BN-R
17
18
SLOT 2
CIRCUIT 1
SLI TIP
SLI RING
35
10
R-S
S-R
19
20
SLOT 2
CIRCUIT 2
SLI TIP
SLI RING
36
11
BK-BL
BL-BK
21
22
SLI TIP
SLI RING
37
12
BK-O
0-BK
23
24
SLI TIP
SLI RING
38
13
BK-G
G-BK
25
26
SLI TIP
SLI RING
39
14
BK-BN
BN-BK
27
28
SLI TIP
SLI RING
40
15
BK-S
S-BK
29
30
SLI TIP
SLI RING
41
16
Y-BL
BL-Y
31
32
SLI TIP
SLI RING
42
17
Y-O
O-Y
33
34
SLOT 3
CIRCUIT 1
SLI TIP
SLI RING
43
18
Y-G
G-Y
35
36
SLOT 3
CIRCUIT 2
SLI TIP
SLI RING
44
19
Y-BN
BN-Y
37
38
SLI TIP
SLI RING
45
20
Y-S
S-Y
39
40
SLI TIP
SLI RING
46
21
V-BL
BL-V
41
42
SLI TIP
SLI RING
47
22
V-O
O-V
43
44
SLI TIP
SLI RING
48
23
V-G
G-V
45
46
SLI TIP
SLI RING
49
24
V-BN
BN-V
47
48
SLI TIP
SLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
SINGLE LINE
TELEPHONE
CONNECT TO ANY DLI CIRCUIT ON
AN 8SDLI CARD.
MDF CONNECTIONS
SLT TO S8SLI CARD
FIGURE 6–8
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
26
1
W-BL
BL-W
1
2
CIRCUIT
FUNCTION
27
2
W-O
O-W
3
4
28
3
W-GN
GN-W
5
6
29
4
W-BR
BR-W
7
8
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 3
SLI TIP
SLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 4
SLI TIP
SLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 5
SLI TIP
SLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 6
SLI TIP
SLI RING
34
9
R-BN
BN-R
17
18
35
10
R-S
S-R
19
20
36
11
BK-BL
BL-BK
21
22
37
12
BK-O
0-BK
23
24
38
13
BK-G
G-BK
25
26
SLOT 2
CIRCUIT 3
SLI TIP
SLI RING
39
14
BK-BN
BN-BK
27
28
SLOT 2
CIRCUIT 4
SLI TIP
SLI RING
40
15
BK-S
S-BK
29
30
SLOT 2
CIRCUIT 5
SLI TIP
SLI RING
41
16
Y-BL
BL-Y
31
32
SLOT 2
CIRCUIT 6
SLI TIP
SLI RING
42
17
Y-O
O-Y
33
34
43
18
Y-G
G-Y
35
36
44
19
Y-BN
BN-Y
37
38
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
SLOT 3
CIRCUIT 3
SLI TIP
SLI RING
47
22
V-O
O-V
43
44
SLOT 3
CIRCUIT 4
SLI TIP
SLI RING
48
23
V-G
G-V
45
46
SLOT 3
CIRCUIT 5
SLI TIP
SLI RING
49
24
V-BN
BN-V
47
48
SLOT 3
CIRCUIT 6
SLI TIP
SLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
SINGLE LINE
TELEPHONE
CONNECT TO ANY SLI CIRCUIT ON
A 2 X 4 CARD.
MDF CONNECTIONS
SLT TO 2 X 4 SLI CARD
FIGURE 6–9
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
1
DLI TIP
DLI RING
27
2
W-0
0-W
3
4
2
DLI TIP
DLI RING
28
3
W-GN
GN-W
5
6
3
DLI TIP
DLI RING
29
4
W-BR
BR-W
7
8
4
DLI TIP
DLI RING
30
5
W-S
S-W
9
10
5
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
6
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
7
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
8
DLI TIP
DLI RING
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
TO CUSTOMER-PROVIDED
DOOR LOCK RELEASE
WHITE
BLUE
LOCK
THREE PAIR
MODULAR CABLE
DOOR BOX
LINE
DOOR PHONE
INTERFACE
MODULE (DPIM)
DOOR PHONE
CONNECT TO ANY DLI CIRCUIT
ON KSU P1.
P+
RED
P-
L1
GREEN
BLACK
MDF CONNECTIONS
DOOR PHONE TO KSU P1
L2
TWO
PAIR
MODULAR
CABLE
YELLOW
FIGURE 6–10
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
SLOT 1
CIRCUIT 1
DLI TIP
DLI RING
27
2
W-O
O-W
3
4
SLOT 1
CIRCUIT 2
DLI TIP
DLI RING
28
3
W-GN
GN-W
5
6
SLOT 1
CIRCUIT 3
DLI TIP
DLI RING
29
4
W-BR
BR-W
7
8
SLOT 1
CIRCUIT 4
DLI TIP
DLI RING
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 5
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 7
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
34
9
R-BN
BN-R
17
18
SLOT 2
CIRCUIT 1
DLI TIP
DLI RING
35
10
R-S
S-R
19
20
SLOT 2
CIRCUIT 2
DLI TIP
DLI RING
36
11
BK-BL
BL-BK
21
22
DLI TIP
DLI RING
37
12
BK-O
0-BK
23
24
DLI TIP
DLI RING
38
13
BK-G
G-BK
25
26
DLI TIP
DLI RING
39
14
BK-BN
BN-BK
27
28
DLI TIP
DLI RING
40
15
BK-S
S-BK
29
30
DLI TIP
DLI RING
41
16
Y-BL
BL-Y
31
32
DLI TIP
DLI RING
42
17
Y-O
O-Y
33
34
SLOT 3
CIRCUIT 1
DLI TIP
DLI RING
43
18
Y-G
G-Y
35
36
SLOT 3
CIRCUIT 2
DLI TIP
DLI RING
44
19
Y-BN
BN-Y
37
38
DLI TIP
DLI RING
45
20
Y-S
S-Y
39
40
DLI TIP
DLI RING
46
21
V-BL
BL-V
41
42
DLI TIP
DLI RING
47
22
V-O
O-V
43
44
DLI TIP
DLI RING
48
23
V-G
G-V
45
46
DLI TIP
DLI RING
49
24
V-BN
BN-V
47
48
DLI TIP
DLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
TO CUSTOMER-PROVIDED
DOOR LOCK RELEASE
WHITE
LOCK
THREE PAIR
MODULAR CABLE
MDF CONNECTIONS
DOOR PHONE TO 8DLI CARD
DOOR BOX
LINE
DOOR PHONE
INTERFACE
MODULE (DPIM)
DOOR PHONE
P+
CONNECT TO ANY DLI CIRCUIT ON
AN 8DLI CARD.
BLUE
RED
P-
L1
L2
GREEN
BLACK
TWO
PAIR
MODULAR
CABLE
YELLOW
FIGURE 6–11
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
26
1
W-BL
BL-W
1
2
CIRCUIT
FUNCTION
27
2
W-O
O-W
3
4
28
3
W-GN
GN-W
5
6
29
4
W-BR
BR-W
7
8
30
5
W-S
S-W
9
10
SLOT 1
CIRCUIT 3
DLI TIP
DLI RING
31
6
R-BL
BL-R
11
12
SLOT 1
CIRCUIT 4
DLI TIP
DLI RING
32
7
R-O
O-R
13
14
SLOT 1
CIRCUIT 5
DLI TIP
DLI RING
33
8
R-G
G-R
15
16
SLOT 1
CIRCUIT 6
DLI TIP
DLI RING
34
9
R-BN
BN-R
17
18
35
10
R-S
S-R
19
20
36
11
BK-BL
BL-BK
21
22
37
12
BK-O
0-BK
23
24
38
13
BK-G
G-BK
25
26
SLOT 2
CIRCUIT 3
DLI TIP
DLI RING
39
14
BK-BN
BN-BK
27
28
SLOT 2
CIRCUIT 4
DLI TIP
DLI RING
40
15
BK-S
S-BK
29
30
SLOT 2
CIRCUIT 5
DLI TIP
DLI RING
41
16
Y-BL
BL-Y
31
32
SLOT 2
CIRCUIT 6
DLI TIP
DLI RING
42
17
Y-O
O-Y
33
34
43
18
Y-G
G-Y
35
36
44
19
Y-BN
BN-Y
37
38
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
SLOT 3
CIRCUIT 3
DLI TIP
DLI RING
47
22
V-O
O-V
43
44
SLOT 3
CIRCUIT 4
DLI TIP
DLI RING
48
23
V-G
G-V
45
46
SLOT 3
CIRCUIT 5
DLI TIP
DLI RING
49
24
V-BN
BN-V
47
48
SLOT 3
CIRCUIT 6
DLI TIP
DLI RING
50
25
V-S
S-V
49
50
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
TO CUSTOMER-PROVIDED
DOOR LOCK RELEASE
WHITE
BLUE
LOCK
THREE PAIR
MODULAR CABLE
DOOR BOX
LINE
DOOR PHONE
INTERFACE
MODULE (DPIM)
DOOR PHONE
P+
RED
P-
L1
L2
GREEN
BLACK
TWO
PAIR
MODULAR
CABLE
YELLOW
CONNECT TO ANY DLI CIRCUIT ON
A 2 X 4 CARD.
MDF CONNECTIONS
DOOR PHONE TO 2 X 4 CARD
FIGURE 6–12
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
CUSTOMER
PROVIDED
STATION EQUIPMENT
OR NT1
CONNECT TO ISDN STATION
EQUIPMENT OR NT1
MDF CONNECTIONS FOR ISDN
STATION TO S4BRI CARD
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
27
2
W-BL
BL-W
W-0
0-W
1
2
3
4
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 1 RECEIVE A
RECEIVE B
28
3
29
4
W-GN
GN-W
W-BR
BR-W
5
6
7
8
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 2 RECEIVE A
RECEIVE B
30
5
31
6
W-SL
SL-W
R-BL
BL-R
9
10
11
12
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 3 RECEIVE A
RECEIVE B
32
7
33
8
R-O
O-R
R-GR
GR-R
13
14
15
16
TRANSMIT A
SLOT 1 TRANSMIT B
CIRCUIT 4 RECEIVE A
RECEIVE B
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
R-BR
BR-R
R-SL
SL-R
BK-BL
BL-BK
BK-O
O-BK
BK-GN
GN-BK
BK-BR
BR-BK
BK-S
S-BK
Y-BL
BL-Y
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SLOT 2
CIRCUIT
1-4
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
Y-O
O-Y
Y-G
G-Y
Y-BN
BN-Y
Y-S
S-Y
V-BL
BL-V
V-O
O-V
V-G
G-V
V-BN
BN-V
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
SLOT 3
CIRCUIT
1-4
50
25
V-S
S-V
49
50
FIGURE 6–13
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
1
5
4
2
3
HOLES FOR MOUNTING SCREWS
NOTE: THE DIRECTORY CARD SLIDE TRAY IS NOT USED WHEN THE
KEYSET IS WALL-MOUNTED.
WALL-MOUNTING A KEYSET
FIGURE6–14
6-7
FIGURE
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
1
2
3
USED FOR ATTACHING
AOM OR 64B MODULE
WITH CONNECTOR CLIP
HOLES FOR MOUNTING SCREWS
NOTE: THE DIRECTORY CARD SLIDE TRAY IS NOT USED WHEN THE
KEYSET IS WALL-MOUNTED.
ULTRA BASE WEDGE
FIGURE6–15
6-7
FIGURE
HOME
PAGE
Table of
Contents
IDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
1
2
3
WALL-MOUNTING
AN iDCS KEYSET
FIGURE
FIGURE6–16
6-7
HOME
PAGE
Table of
Contents
GROOVE FOR
ADDITIONAL
CONNECTOR
CLIP
INSTALLATION
PART 6 JUNE 2002
24B / 12B ULTRA BASE WEDGE
METAL
CONNECTOR
CLIP
64BM ULTRA BASE WEDGE
iDCS 100
TECHNICAL MANUAL
ATTACHING 24B/12B TO 64BM
FIGURE6–17
6-7
FIGURE
HOME
PAGE
Table of
Contents
METAL
CONNECTOR
CLIP
GROOVE FOR
ADDITIONAL
CONNECTOR
CLIP
INSTALLATION
PART 6 JUNE 2002
24B / 12B ULTRA BASE WEDGE
AOM ULTRA BASE WEDGE
iDCS 100
TECHNICAL MANUAL
ATTACHING 24B/12B TO AOM
FIGURE 6–18
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 6 JUNE 2002
7B / SINGLE LINE ULTRA BASE WEDGE
AOM ULTRA BASE WEDGE
METAL CONNECTOR CLIP
7B/SINGLE LINE ULTRA BASE WEDGE
64BM ULTRA BASE WEDGE
METAL CONNECTOR CLIP
ATTACHING
7B/SINGLE LINE TO AOM AND
7B/SINGLE LINE TO 64BM
FIGURE6–19
6-7
FIGURE
HOME
PAGE
Table of
Contents
IDCS 100
TECHNICAL MANUAL
ATTACHING
iDCS 64B MODULE
TO AN iDCS KEYSET
INSTALLATION
PART 6 JUNE 2002
FIGURE6–20
6-7
FIGURE
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
PART 7. CONNECTING OPTIONAL EQUIPMENT
7.1 MUSIC ON HOLD/BACKGROUND MUSIC
Connect each customer-provided music source to the music input on the KSU
connecting block (see Figure 7–1). The music input has internal automatic gain
compensation features.
NOTE: The MOH input on the KSU can be switched between internal chimes and an
outside source. The jumper S1 must be set to EXT for an external source to be
available (see Figure 7-2 for the location of S1).
IMPORTANT NOTICE: In accordance with US Copyright Law, a license may be
required from the American Society of Composers, Authors and Publishers (ASCAP) or
another similar organization if copyrighted music is transmitted through the Music on
Hold feature. Samsung Telecommunications America, Inc. hereby disclaims any
liability arising out of failure to obtain such a license.
Each C.O. line (trunk) can be programmed to receive a music source, system
generated TONE or NO MUSIC when it is put on hold (see MMC 408). Each keyset can
receive a music source or NO MUSIC for background music. See programming manual
for instructions (MMC 308).
7.2 EXTERNAL PAGING
The KSU provides a voice pair to be used with customer-provided paging equipment.
Connect the customer provided paging equipment to the page 1 output pins of the P1
connecting block (see Figure 7–3). The page voice pair is 600 Ohms impedance. When
the amplifier page input is not 600 ohm, a suitable impedance matching transformer
must be used.
The KSU has a relay associated with the page output. This relay may be used for
amplifier muting (see Figure 7-3) or zone control (see Figure 7-4). This relay contact
pair is for control of low voltage circuits or amplifier output. The contacts are rated at 24
VDC-1 amp.
If installed, the SMISC card provides a second voice pair for connection to a second
amplifier and 3 relays that may be defined as page zone control in MMC 219 and
assigned in MMC 605 (see Figure 7–4). These relay contact pairs are for control of low
voltage circuits or amplifier output. The contacts are rated at 24 VDC-1 amp.
WARNING: Do not attempt to connect commercial AC power to these contacts.
7.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
The SMISC card also provides a second independently controlled page output voice
pair to be used with customer-provided paging equipment. Connect the customer
provided paging equipment to the page 2 output pins of the P1 connecting block (see
Figure 7–3). The page voice pair is 600 Ohms impedance. When the amplifier page
input is not 600 ohm, a suitable impedance matching transformer must be used.
7.3 COMMON BELL
A customer-provided loud ringing device can be controlled using one of the relay
contact pairs on the SMISC card (see Figure 7–5). Each of these 3 relays can be
individually defined as a common bell in MMC 219 and assigned in MMC 204. These
relay contact pairs are for control of low voltage circuits or amplifier output. The
contacts are rated at 24 VDC-1 amp.
Programming allows for INTERRUPTED or CONTINUOUS operation of the contacts
using MMC 204. The interrupted selection follows the C.O. ring cadence—one second
ON/three seconds OFF.
After connecting a common bell, you must assign it to a group in MMC 601 as a ring
destination by using the code for Common Bell.
The basic steps for common bell operation are the following:
a.
b.
c.
d.
e.
Wire the loud ringing device to the common bell control contact pair.
Program the relay as a common bell in MMC 219.
Program the contacts for continuous or steady operation.
Program the station hunt group to include the common bell.
Assign the trunk to ring the hunt group containing the common bell.
Common bell control can be used with station hunt groups, individual stations and
Universal Answer. Contacts are rated at 24 VDC-1 amp.
WARNING: Do not attempt to connect commercial AC power to these contacts.
7.4 RING OVER PAGE
When a customer-provided paging system is installed, incoming calls can be assigned
to ring over page. Program the line or lines to ring a hunt group. Using MMC 601,
assign ROP as a destination in this hunt group. Ring over page can be used for day or
night operation or both.
7.5 STATION MESSAGE DETAIL RECORDING (SMDR)
To receive an SMDR printout, connect a customer-provided printer to one of the serial
interface connectors on the SMISC card (see Figure 7–6). SI/O 2 defaults as SMDR.
7.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
Use a pin to pin RS232C cable. Only pins 2, 3, 5 and 7 are required (see Figure 7–7).
When the printer or optional call accounting device needs to be more than 15 feet away
from the KSU, use shielded computer cable. Attach a male DB9 connector to the
SMISC end and then attach one that matches the requirements of the call accounting
device or printer to the other end. This cable must not exceed 300 feet.
Use MMC 725 to set SMDR print options and MMC 804 to set the transmission
parameters and the SMISC port.
7.6 PC PROGRAMMING
To program the system via a personal computer (PC), connect a PC equipped with
PCMMC to a serial interface connector on the SMISC card (see Figure 7–6). SI/O 1
defaults as PCMMC.
Use an RS232C cable with connections as shown in Figure 7–8. When the PC needs to
be more than 15 feet away from the KSU, use shielded computer cable. Attach a male
DB9 connector to the SMISC end and then attach one that matches the requirements
of the PC to the other end. This cable must not exceed 300 feet.
Use MMC 804 to set the transmission parameters and the SMISC port.
7.7 REMOTE PROGRAMMING
To remotely program a system, connect a customer-provided modem to a serial
interface connector on the SMISC card (see Figure 7–6).
Use an RS232C cable as shown in Figure 7–9. When the modem needs to be more
than 15 feet away from the KSU, use shielded computer cable. Attach a male DB9
connector to the SMISC end and then attach one that matches the requirements of the
modem to the other end. This cable must not exceed 300 feet.
Use MMC 804 to set the transmission parameters and the SMISC port to be used.
7.8 POWER FAILURE TRANSFER (PFT)
When the system loses AC power, the first two loop start lines of each S3TRK card are
automatically switched to the PFT pairs on the connecting block (see Figure 7–10).
Cross-connect these outputs as shown in Figure 7–10 to the TIP and RING pairs of the
single line phones that are to have power failure operation.
7.9 VOICE MAIL/AUTO ATTENDANT
System operation provides special programming and hardware for use with a
customer-provided voice mail/auto attendant system. The single line stations on the 2
SLI card, S8SLI card and the 2 X 4 SLI card can provide a disconnect signal required
7.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
for VM/AA operation. Use one pair twisted #24 AWG or #26 AWG jumper wire to crossconnect these SLI circuits to the VM/AA system (see Figure 7–11).
Program these ports for VM/AA use in MMC 207 and set VM/AA options in MMC 726.
As default MMC 726 comes programmed to interface with StarmaiL. See the Standard
Telephone User Guide for feature codes and instructions (how to light message lights
etc.).
7.10 CONNECTING SYSTEM BACKUP BATTERIES TO
THE iDCS 100 POWER SUPPLY
The iDCS 100 power supply contains a monitoring circuit to switch the system to
customer provided 48VDC batteries when AC power is interrupted. Calls in progress
are not disconnected. The power supply circuitry monitors and recharges batteries as
needed.
Connect four 12V batteries or eight 6V batteries in series. Any NICAD or lead acid (car
or motorcycle type) battery can be used if its rating is not less than 6AH (amp hours)
but not more than 40 AH. The batteries must be located within three feet of the KSU.
Use the factory-supplied wire harness with 36" red and black leads to connect batteries
(see Figure 7-12).
Observe the following precautions when installing batteries:
a. Make sure the batteries you install conform to local building, fire and safety codes.
Some battery types emit hydrogen gas during the charging state and may require
venting to fresh air.
b. Do not place batteries directly on a concrete floor. This causes them to discharge
very quickly.
c. Follow the battery manufacturer’s recommended installation and maintenance
procedures.
7.4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
PIN
COLOR
TERM CIRCUIT
41
Y-BL
31
16
BL-Y
32
42
Y-O
33
17
O-Y
34
1
2
FUNCTION
MOH 1 MOH 1 +
MOH 2 MOH 2 +
CUSTOMER-PROVIDED
MUSIC SOURCE
CUSTOMER-PROVIDED
MUSIC SOURCE
CONNECT ONE MUSIC SOURCE
TO EACH INPUT AS NEEDED.
NOTE: MOH 2 REQUIRES AN
SMISC CARD.
MDF CONNECTIONS CONNECTING
MOH SOURCES TO KSU
FIGURE 7–1
HOME
PAGE
Table of
Contents
IDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
S1
EXT INT
MOH
MOH
SET SWITCH S1 TO INT FOR
CHIMES TO BE HEARD ON
PORT 371
OR
SET SWITCH S1 TO EXT
FOR AN EXTERNAL SOURCE
TO BE HEARD ON PORT 371
SETTING JUMPER SWITCH S1
FIGURE 7–2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
600
PIN
COLOR
TERM
CIRCUIT
FUNCTION
40
15
BK-S
S-BK
29
30
R1
RELAY 1 +
RELAY 1 –
41
16
Y-BL
BL-Y
31
32
MOH 1 +
MOH 1 –
42
17
Y-O
O-Y
33
34
MOH 2 +
MOH 2 –
43
18
Y-G
G-Y
35
36
1
PAGE 1 +
PAGE 1 –
44
19
Y-BN
BN-Y
37
38
2
PAGE 2 +
PAGE 2 –
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
R2
RELAY 2 +
RELAY 2 –
47
22
V-O
O-V
43
44
R3
RELAY 3 +
RELAY 3 –
48
23
V-G
G-V
45
46
R4
RELAY 4 +
RELAY 4 –
49
24
V-BN
BN-V
47
48
MUTE
IN
OUT
CUSTOMER-PROVIDED
AMPLIFIER
ALARM +
ALARM –
N O T E : T H E Z O N E R E L AY S
REQUIRE AN SMISC CARD.
MDF CONNECTIONS CONNECTING
PAGE AMPLIFIER TO KSU
FIGURE 7–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
CUSTOMER-PROVIDED
PAGING AMPLIFIER
PIN
COLOR
TERM
CIRCUIT
FUNCTION
40
15
BK-S
S-BK
29
30
R1
RELAY 1 +
RELAY 1 –
41
16
Y-BL
BL-Y
31
32
42
17
Y-O
O-Y
33
34
43
18
Y-G
G-Y
35
36
1
44
19
Y-BN
BN-Y
37
38
2
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
R2
RELAY 2 +
RELAY 2 –
ZONE 5
47
22
V-O
O-V
43
44
R3
RELAY 3 +
RELAY 3 –
ZONE 6
48
23
V-G
G-V
45
46
R4
RELAY 4 +
RELAY 4 –
ZONE 7
49
24
V-BN
BN-V
47
48
IN
OUT
ALARM +
ALARM –
NOTE: THE ZONE RELAYS
REQUIRE AN SMISC CARD.
MDF CONNECTIONS CONNECTING
PAGE AMPLIFIER TO KSU
FIGURE 7–4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1
PIN
COLOR
TERM
CIRCUIT
FUNCTION
41
16
Y-BL
BL-Y
31
32
MOH 1 +
MOH 1 –
42
17
Y-O
O-Y
33
34
MOH 2 +
MOH 2 –
43
18
Y-G
G-Y
35
36
PAGE 1 +
PAGE 1 –
44
19
Y-BN
BN-Y
37
38
PAGE 2 +
PAGE 2 –
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
R1
RELAY 2 +
RELAY 2 –
47
22
V-O
O-V
43
44
R2
RELAY 3 +
RELAY 3 –
48
23
V-G
G-V
45
46
R3
RELAY 4 +
RELAY 4 –
49
24
V-BN
BN-V
47
48
CUSTOMER-PROVIDED
COMMON BELL
ALARM +
ALARM –
CONNECT THE COMMON BELL TO ONE OF THE
RELAYS ON THE SMISC CARD.
YOU MUST PROGRAM THIS RELAY IN MMC 219
AS A COMMON BELL RELAY.
MDF CONNECTIONS
COMMON BELL CONTACTS
FIGURE 7–5
HOME
PAGE
Table of
Contents
TNR1
iDCS 100
TECHNICAL MANUAL
U23
U12
P1
P2
Y1
C8
C26
RLY3
C7
U5
C19
T1
C33
U21
RLY1
C25
U4
RLY2
C7
T2
U6
B4
B5 U20
C32
B3
B3
C34
U11
B4
B5 U20
C32
C34
U19
U31
D7
U19
U31
D7
B2
U15
DSS1 U18
B2
U15
DSS1 U18
Y2
C27
Y2
C27
U11
U29
C29
U11
U29
C29
BAT1
U28
D1
U27
P7
D1
U27
P7
U11
U26
U26
U17
U17
MISC
U4
U18
U30
U3
U9
U3
U9
BAR CODE
U2
U8
U14
U25
BAR CODE
U13
Y1
C8
U5
C19
T1
C33
U21
RLY1
C25
U4
RLY2
U7
U23
U12
P1
P2
C26
RLY3
MISC
U1
TNR2
TNR3
TNR1
TNR2
TNR3
T2
FIGURE 7–6
SMISC 1 AND 2 CARDS
Table of
Contents
INSTALLATION
PART 7 JUNE 2002
HOME
PAGE
U24
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
SMISC CARD
PRINTER
RXD 2
2
TXD 3
3
GND 5
7
DTR 4
20
PIN CONNECTIONS FOR SMISC
CARD TO PRINTER
FIGURE 7–7
SMISC CARD
PC
COM 1
RXD 2
2
TXD 3
3
GND 5
5
DTR 4
PIN CONNECTIONS FOR SMISC
CARD TO PERSONAL COMPUTER
4
9 PIN
COM 2
3
OR
2
7
20
25 PIN
FIGURE 7–8
SMISC CARD
MODEM
RXD 2
2 TXD
TXD 3
3 RXD
DTR 4
20 DTR
GND 5
7 GND
RTS 7
4 RTS
CTS 8
5 CTS
PIN CONNECTIONS FOR SMISC
CARD TO MODEM
FIGURE 7–9
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2
25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5
PIN
COLOR
TERM
CIRCUIT
FUNCTION
26
1
W-BL
BL-W
1
2
SLOT 1
TRUNK 1
C.O. TIP
C.O. RING
27
2
W-O
O-W
3
4
SLOT 1
TRUNK 2
C.O. TIP
C.O. RING
28
3
W-GN
GN-W
5
6
SLOT 1
TRUNK 3
C.O. TIP
C.O. RING
29
4
W-BR
BR-W
7
8
30
5
W-S
S-W
9
10
SLOT 1
TRUNK 1
PFT1 TIP
PFT1 RING
31
6
R-BL
BL-R
11
12
SLOT 1
TRUNK 1
PFT2 TIP
PFT2 RING
32
7
R-O
O-R
13
14
33
8
R-G
G-R
15
16
34
9
R-BN
BN-R
17
18
SLOT 2
TRUNK 1
C.O. TIP
C.O. RING
35
10
R-S
S-R
19
20
SLOT 2
TRUNK 2
C.O. TIP
C.O. RING
36
11
BK-BL
BL-BK
21
22
SLOT 2
TRUNK 3
C.O. TIP
C.O. RING
37
12
BK-O
O-BK
23
24
38
13
BK-G
G-BK
25
26
SLOT 2
TRUNK 1
PFT1 TIP
PFT1 RING
39
14
BK-BN
BN-BK
27
28
SLOT 2
TRUNK 2
PFT2 TIP
PFT2 RING
40
15
BK-S
S-BK
29
30
41
16
Y-BL
BL-Y
31
32
42
17
Y-O
O-Y
33
34
SLOT 3
TRUNK 1
C.O. TIP
C.O. RING
43
18
Y-G
G-Y
35
36
SLOT 3
TRUNK 2
C.O. TIP
C.O. RING
44
19
Y-BN
BN-Y
37
38
SLOT 3
TRUNK 3
C.O. TIP
C.O. RING
45
20
Y-S
S-Y
39
40
46
21
V-BL
BL-V
41
42
SLOT 3
TRUNK 1
PFT1 TIP
PFT1 RING
47
22
V-O
O-V
43
44
SLOT 3
TRUNK 2
PFT2 TIP
PFT2 RING
CONNECTING SLTS TO PFT
CIRCUITS ON S3TRK CARD
PFT PHONE
FOR C.O. 1
PFT PHONE
FOR C.O. 2
FIGURE 7–10
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
25 PAIR CABLE TO KSU
CIRCUIT
1
2
FUNCTION
SLT TIP
SLT RING
SLT TIP
SLT RING
ONE PAIR TWISTED
SHEATHED STATION CABLE
24 OR 26 AWG
R
G
BK
Y
W
BL
1
2
3
4
5
6
CONNECT TO ANY CIRCUIT ON 2
SLI CARD, S8SLI CARD OR
2 X 4 SLI CARD.
VOICE PROCESSING SYSTEM
MDF CONNECTIONS
VOICE MAIL TO SLI CARD
FIGURE 7–11
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 7 JUNE 2002
RESERVE POWER
BATTERY CONNECTOR
POWER SUPPLY
BLACK
RED
CONNECT TO EITHER A OR B
+
–
12V
+
–
12V
+
–
+
12V
–
+
12V
+
–
+
6V
6V
+
–
–
+
+
–
6V
6V
+
–
–
–
6V
6V
+
–
OPTION A
+
6V
–
+
6V
–
OPTION B
BATTERIES SHOULD BE PLACED
WITHIN THREE FEET OF KSU
RESERVE POWER BATTERY
CONNECTIONS
FIGURE 7–12
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
PART 8. INSTALLING KEYSET
DAUGHTERBOARDS
8.1 KDB DLI
Before performing this procedure, the line cord must be unplugged from the keyset.
The base wedge should then be removed, the keyset should be placed face down on a
soft surface and the four base retaining screws removed (see Figure 8–1).
The base should now be separated from the keyset and the keyset top half set aside.
The KDb DLI can now be attached to the keyset base with the four screws supplied
(see Figure 8–2). Care should be taken to ensure that the modular socket shows
through the access hole in the base (see Figure 8–3).
Invert the base assembly over the keyset and plug the ribbon cable into the socket on
the keyset PCB (see Figure 8–4) while making sure no damage occurs to the keyset
PCB. Reattach the base to the keyset and test to ensure normal keyset operation.
8.2 KDB SLI
Before performing this procedure, the line cord must be unplugged from the keyset.
The base wedge should then be removed, the keyset should be placed face down on a
soft surface and the four base retaining screws removed (see Figure 8–1).
The base should now be separated from the keyset and the keyset top half set aside.
The KDb SLI can now be attached to the keyset base with the six screws supplied (see
Figure 8–5). Care should be taken to ensure that the modular socket shows through
the access hole in the base (see Figure 8–3).
Invert the base assembly over the keyset and plug the ribbon cable into the socket on
the keyset PCB (see Figure 8–4) while making sure no damage occurs to the keyset
PCB. Reattach the base to the keyset and test to ensure normal keyset operation.
8.3 CONNECTING TO THE KDBS
There are two methods for connecting devices to keyset daughterboards. The simplest
method is to connect the second device directly by means of a line cord (see Figures
8–6 and 8–7).
The second method is to use a multi-pair station cable, connecting separate station
jacks to the first two pairs. A line cord can now be connected between the
daughterboard and the second jack. This will return the daughterboard port to the MDF
for cross-connection to another cable run (see Figure 8–8).
8.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
HANDSET
TEL
RETAINING SCREWS
RETAINING SCREWS
KEYSET BASE
FIGURE 8–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
MOUNTING SCREWS
RIBBON CABLE CONNECTOR
INSTALLING KDB
DLI DAUGHTERBOARD
FIGURE 8–2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
KEYSET DAUGHTERBOARD
OUTPUT JACK
HANDSET
TEL
OUTPUT JACK
FIGURE 8–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
HOOK
P1
P2
P7
SP
MIC
PLUG RIBBON CABLE FROM DAUGHTERBOARD
INTO RIBBON CABLE CONNECTOR P7
CONNECTING KEYSET
DAUGHTERBOARD TO
KEYSET PCB
FIGURE 8–4
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
RIBBON
CABLE
CONNECTOR
MOUNTING
SCREWS
INSTALLING KDB
SLI DAUGHTERBOARD
FIGURE 8–5
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
LINE CORD
SCROLL
VOL
OUTPUT
JACK
SPK
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
TEL
0OPER
HANDSET
ANS/
RLS
SECOND KEYSET
FIRST KEYSET
CONNECTING A KEYSET
TO A KDB-DLI
FIGURE 8–6
LINE CORD
OUTPUT
JACK
TEL
HANDSET
SINGLE LINE TELEPHONE
FIRST KEYSET
CONNECTING A SINGLE LINE
TELEPHONE TO A KDB-SLI
FIGURE 8–7
HOME
PAGE
Table of
Contents
MDF
MULTI-PAIR
STATION
CABLE
G
G
G
R
R
R
Y
Y
Y
BK
BK
BK
BL
W
BL
W
BL
W
6
5
4
3
2
1
6
5
4
3
2
1
6
5
4
3
2
CONNECTING A STATION DEVICE
TO A KDB VIA THE MAIN
DISTRIBUTION FRAME
1
VOL
SPK
ANS/
RLS
TRSF
HOLD
6 MNO
0OPER
9 WXY
3 DEF
5 JKL
8 TUV
2 ABC
4 GHI
7 PRS
1
SCROLL
CONNECT TO KEYSET OR SLT
DEPENDING ON KDB TYPE
TEL
HANDSET
CROSS-CONNECT
SECOND PAIR TO
DIFFERENT STATION
CABLE
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 8 JUNE 2002
FIGURE 8–8
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 9 JUNE 2002
PART 9. CHANGING SOFTWARE
9.1 REPLACING THE EPROMS
The first thing you should do before proceeding is to discharge any static electricity
you may have gathered by touching a ground point such as the cover of the KSU
Power Supply. When you have done this then check the iDCS MEM3 card and ensure
that the memory switch is in the ON position. Next turn the KSU off and disconnect the
backup batteries, if equipped, from the power supply. Remove the iDCS MEM3 card by
gently pulling on the card ejectors. Lay the iDCS MEM3 card face up on a nonconductive surface.
NOTE: It is advisable to use PCMMC to produce a backup copy of the customer
database before turning the system off in case problems arise and the original
database on the iDCS MEM3 card is lost.
Gently remove the EPROMS from the iDCS MEM3 card using a chip extraction tool or
by gently prying with a small flat bladed screwdriver. Set the removed EPROMS aside
carefully in case they need to be reinstalled (see Figure 9–1).
Remove the new EPROMS from their protective packaging and confirm that the legs on
the EPROMS are straight. If the legs are not straight, contact Samsung Technical
Support for assistance. Carefully insert the new EPROMS in their designated sockets.
Install the MEM3 card and plug in the 25 pair cable for P1 of the motherboard.
Switch on the KSU and verify that it is operating. If the KSU does not operate, remove
the new EPROMS and reinstall the old EPROMS and test again. If the system still fails
to operate, contact Samsung Technical Support.
9.2 SOFTWARE UPGRADE VIA iDCS PCMMC
(MEM4 ONLY)
When a software change is required, it must be done via PCMMC through the LAN
interface. Please refer to the PCMMC Technical Manual to perform a software upgrade
for a MEM4 card.
9.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
ON
OFF
INSTALLATION
PART 3 JUNE 2002
RESET
U14
U15
U6
U5
U4
U3
LED1
SW2
D3 D2 D1
U7
C10
U10
ODD2
U12
EVN2
ODD1
EVN1
U2
U11
U9
U13
BAR CODE
P1
C14
BT1
iDCS MEM3 CARD
FIGURE 9–1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 10 JUNE 2002
PART 10. INSTALLING CALLER ID
10.1 GENERAL INFORMATION
In order to install Caller ID on a iDCS 100, you must have the following pieces of iDCS
100 equipment available:
A personal computer with the latest version of PCMMC for the iDCS 100 is recommended.
This will allow the original system database to be saved in the case of an upgrade to an
existing system.
The iDCS 100 is compatible with both types of Caller ID as defined by BELLCORE. These
are the single message format or “Number Only” sometimes referred to as standard Caller
ID and the multiple message format or “Name and Number” sometimes referred to as
Deluxe Caller ID. In the case of Number Only delivery, there is a translation table available
to add names to the delivered number.
The MMCs related to Caller ID are listed below with a short description of their use. They
are listed in the recommended order in which they should be programmed. This sequence
is suggested so that the installer gets a better understanding of how the feature works.
There is no technical reason to follow this sequence.
!
MMC 414 CID TRUNKS
This MMC is used by the technician to determine
which trunks will receive Caller ID data.
!
MMC 312 ALLOW CID
This MMC is used by the technician to determine
which keysets are allowed to receive Caller ID
displays.
!
MMCs 722 and 723
These MMCs have had new keys related to Caller
ID features added to them. It is strongly
recommended that all keysets allowed Caller ID in
MMC 312 are programmed with a CID key.
!
MMC 729 CID TRANSLATION
This MMC allows the technician to create a list of
names that correspond to numbers received from
the central office. These names will be displayed
when a call rings in that has Number Only data
provided by the CO.
!
MMC 725 SMDR OPTIONS
The ability to print Caller ID data and abandoned
calls has been added to this MMC.
10.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 10 JUNE 2002
!
MMC 119 CID DISPLAY
This MMC is used by the end user to determine
which piece of Caller ID data is displayed when a
call rings at the user’s station.
!
MMC 501 SYSTEM TIMERS
This MMC has two new timers related to Caller ID.
The only timer that may need adjustment is the
CID DISPLAY TIME. This is the length of time that
CID data will be displayed after the CID key is
pressed.
!
MMC 415 TRK ABANDON
This MMC is used by the technician to determine
which trunks will record data in the Call Abandon
list and print with an Abandon “A” flag on SMDR.
!
MMC 608 CID BLOCK
This MMC is used by the technician to assign CID
Review blocks to keysets to allow the user to
review CID data for previous calls.
!
MMC 701 CLASS OF SERVICE
All of the Caller ID features have been added to
this MMC to enable the technician to allow or
deny them.
!
MMC 724 NUMBER PLAN
The Caller ID features have been added to this
MMC to allow a technician to assign an access
code where necessary.
10.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 11 JUNE 2002
PART 11. ADDING CARDS TO AN EXISTING
SYSTEM
11.1 ADDING AN SMISC CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the SMISC2 card into the slot labeled MISC.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The port
numbers and recommended directory numbers are listed in the table below. These
directory numbers are the same as the numbers that would have been assigned
when the system was first installed.
ITEM
PORT NUMBER
DIRECTORY NUMBER
AA PORT 1
023
381
AA PORT 2
024
382
AA PORT 3
025
383
AA PORT 4
026
384
MOH/BGM 2
027
372
PAGE OUTPUT 2
028
362
RELAY 1
029
363
RELAY 2
030
364
RELAY 3
031
365
ALARM SENSOR
032
352
11.2 ADDING A 2 SLI CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the 2 SLI card into the slot labeled SLI.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The port
numbers for the 2 SLI are listed in the following table.
11.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 11 JUNE 2002
ITEM
PORT NUMBER
SLI PORT 1
019
SLI PORT 2
020
11.3 ADDING AN S3TRK CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the S3 TRK card into an empty universal slot.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The S3 TRK
card uses the first three ports of each slot (see figure 11–1).
11.4 ADDING AN S6TRK CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the S6 TRK card into an empty universal slot.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The S6 TRK
card uses the first six ports of each slot (see figure 11–1).
11.5 ADDING AN S8DLI CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the S8 DLI card into an empty universal slot.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The S8 DLI
card uses all 8 ports of each slot (see figure 11–1).
11.6 ADDING AN S8SLI CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the S8 SLI card into an empty universal slot.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The 8 card SLI
uses all 8 ports of each slot (see figure 11–1).
11.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 11 JUNE 2002
11.7 ADDING A 2 X 4 CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the 2 X 4 card into an empty universal slot.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The 2 X 4 card
uses the first six ports of each slot (see figure 11–1). The first two ports are the CO
lines and the third through sixth are the station ports.
11.8 ADDING AN S4BRI CARD
1.
2.
3.
4.
5.
6.
Check the battery switch on the MEM3 or MEM4 card and make sure it is ON.
Turn off power to the system and unplug the power cord.
Insert the card into an empty universal slot.
Restore power to the system.
Open system programming and use MMC 806 to initialize the card.
Use MMC 724 to assign directory numbers to the ports on the card. The BRI card
uses all 8 ports of each slot (see figure 11–1).
NOTE: SPLL required in system to support S4BRI operation.
KSU PORT NUMBERS
EKSU PORT NUMBERS
SLOT 1
SLOT 2
SLOT 3
SLOT 1
SLOT 2
SLOT 3
SLOT 4
033
041
049
057
065
073
081
034
042
050
058
066
074
082
035
043
051
059
067
075
083
036
044
052
060
068
076
084
037
045
053
061
069
077
085
038
046
054
062
070
078
086
039
047
055
063
071
079
087
040
048
056
064
072
080
088
FIGURE 11–1
11.3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 11 JUNE 2002
11.9 ADDING AN SPLL DAUGHTER BOARD
1. Check the battery switch on the MEM3 or MEM4 card and make sure it is on.
2. Turn off power to the system and unplug the power cord.
3. Install the SPLL card onto its connectors in the bottom left hand corner of the KSU
motherboard (see Figure 11–2).
4. Restore power to the system.
NOTE: The SPLL DAUGHTER BOARD is required in system to support BRI operation.
11.10 ADDING A MODEM CARD
1. Check the battery switch on the MEM3 or MEM4 card and make sure it is on.
2. Turn off the power to the system and unplug the power cord.
3. Remove the SMISC card from its slot, and lay card on a soft surface, component
side up.
4. Install the MODEM card onto its connectors on the SMISC card (see Figure 11–3).
NOTE: The white arrow on the MODEM card should point away from the KSU
Motherboard when SMISC card is re-inserted.
5. Re-insert SMISC card into the appropriate slot.
6. Restore power to the system.
7. Open system programming and use MMC 806 to initialize the card.
8. Use MMC 724 to assign a directory number to the card, the default extension
number is 359.
11.4
HOME
PAGE
Table of
Contents
UNIVERSAL SLOT 3
UNIVERSAL SLOT 1
UNIVERSAL SLOT 2
MISC SLOT
MEM SLOT
INSTALLATION
PART 11 JUNE 2002
2 SLI SLOT
iDCS 100
TECHNICAL MANUAL
SPLL
DAUGHTER
BOARD
U10
U9
U8
U15
L3
D2
L2
Y1
C2
C13
C3
L1
U13
U7
U11
B3
U16
U6
U14
U3
U5
B5
U4
U1
PLL
U2
SPLL INSTALLATION ON
KSU MOTHERBOARD
FIGURE 11–2
HOME
PAGE
Table of
Contents
TNR3
TNR2
TNR1
P2
U23
U12
P1
C26
RLY3
C8
Y1
U5
RLY2
C33
U21
T1
RLY1
C25
U4
C19
C7
T2
C32
B3
C34
B5 U20
U11
B4
U31
D7
U19
DSS1 U18
U15
B2
C27
Y2
C29
U29
U11
P7
U27
D1
U2
U26
C13
MODEM CARD INSTALLATION ON
SMISC CARD
U1
U11
MISC
C15
C18
U10
C6
C4
C1
C2
U14
MODEM
CARD
U3
X1
U17
L1
U4
U9
U3
U5
U6
MODEM
BAR CODE
BAR CODE
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 11 FEBRUARY 2002
MODEM CARD
SMISC 1 OR 2 CARD
FIGURE 11–3
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 12 JUNE 2002
PART 12. INSTALLING A SVMi-8 CARD
12.1 SYSTEM SIZE WITH SVMi-8
For the purpose of assigning system resources the SVMi-8 card consumes the
equivalent system capacity of 8 keysets. This means that when a SVMi-8 card is
installed in the iDCS 100 the system can now support a maximum of 32 (or 48 with
SPSU2) station devices. This capacity includes keysets, any device connected to a
keyset port, SLTs and keyset daughter boards.
12.2 REMOVING THE COVER
Before the SVMi-8 card can be installed in the iDCS 100 the card module must first be
disassembled to allow the card to fit the slot. To disassemble the SVMi-8 card, first
remove the ejector tabs by pulling them outward until they snap off. Next, to separate
the two halves of the casing, remove the four screws and pull the two halves apart. This
releases the SVMi-8 card PCB.
12.3 ADDING A SECOND VOICE PROCESSING
MODULE (VPM)
The first thing you should do before proceeding is to discharge any static electricity
you may have gathered by touching a ground point such as the cover of the KSU
Power Supply. When you have done this then lay the SVMi-8 card face up on a nonconductive surface.
Position the second VPM over the card connector on the SVMi-8 base board and gently
apply pressure until the card seats. The SVMi-8 card can now be installed in the KSU.
12.4 INSERTING THE CARD
The SVMi-8 card is installed in the far right slot of the expansion cabinet. This is the slot
with the black DCS style connector. The first thing you should do before proceeding is
to discharge any static electricity you may have gathered by touching a ground point
such as the cover of the KSU Power Supply. When you have done this then check the
power switch on the left-hand side of the KSU and ensure that the switch is in the OFF
position. Next position the SVMi-8 card in the grooves of the card guide and gently
slide the card in until it makes contact with the connector. Press gently but firmly on the
top and bottom of the front edge of the card until the card seats in its connector.
12.5 UPGRADING AN EXISTING CARD TO 8 PORTS
The first thing you should do before proceeding is to discharge any static electricity
you may have gathered by touching a ground point such as the cover of the KSU
12.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 12 JUNE 2002
Power Supply. When you have done this then check the MEM3 or MEM4 card and
ensure that the memory switch is in the ON position. Next turn the KSU off and remove
the SVMi-8 card by gently pulling on the card. Lay the SVMi-8 card face up on a nonconductive surface.
Position the second VPM over the card connector on the SVMi-8 base board and gently
apply pressure until the card seats. The SVMi-8 card can now be reinstalled in the KSU.
12.2
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 13 JUNE 2002
PART 13. INSTALLING A SVMi-4 CARD
13.1 SYSTEM SIZE WITH A SVMi-4 CARD INSTALLED
For the purposes of assigning system resources the SVMi-4 card consumes the
equivalent system capacity of 4 keysets. This means that when a SVMi-4 card is
installed in the iDCS 100 the system can now support a maximum of 52 station devices.
This capacity includes keysets, any device connected to a keyset port, SLTs and
keyset daughter boards.
13.2 UPGRADING THE SVMi-4 TO FOUR PORTS
Before it will operate in the iDCS 100, the SVMi-4 must be upgraded to four ports as
follows. Upgrading the SVMi-4 card basically means installing an upgrade key into its
dedicated socket.
The first thing you should do before proceeding is to discharge any static electricity
you may have gathered by touching a ground point such as the cover of the KSU
Power Supply. When you have done this then lay the SVMi-4 card face up on a nonconductive surface.
Position the upgrade key over the socket (see Figure 13–1) on SVMi-4 base board with
one edge of the upgrade key under the spring clip and gently apply pressure until the
upgrade key seats. The SVMi-4 card can now be installed in the KSU.
Note: The upgrade key will only fit in the socket with the flat side uppermost.
13.1
HOME
PAGE
Table of
Contents
iDCS 100
TECHNICAL MANUAL
INSTALLATION
PART 13 JUNE 2002
U32
Upgrade Key
Socket
U34
Z2
U33
U36
U14
U15
J1
U1
SIO Port
BAR CODE
J5
U41
U29
U28
U19
U23
U9
U8
S1
U30 J4
Reset Button
U27
U25
U10
U26
U21
U24
Compact Flash
Socket
SVMi-4 CARD
FIGURE 13–1
HOME
PAGE
Table of
Contents