Zanussi MW 2132 Operating instructions

VSX-820_PWXCN_En.book 1 ページ
2010年4月2日 金曜日 午後1時30分
VSX-820-K
VSX-820_PWXCN_En.book 2 ページ
2010年4月2日 金曜日 午後1時30分
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D3-4-2-1-1_A1_En
WARNING
VENTILATION CAUTION
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 40 cm at top, 10 cm at rear, and 20 cm at each
side).
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
VSX-820_PWXCN_En.book 3 ページ
2010年4月2日 金曜日 午後1時30分
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
D3-4-2-2-1a_A1_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, Surround EX
and the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license under U.S.
Patent #’s: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S.
and worldwide patents issued & pending.
DTS and the Symbol are registered
trademarks, & DTS-HD, DTS-HD Master
Audio, and the DTS logos are trademarks of
DTS, Inc. Product includes software. © DTS,
Inc. All Rights Reserved.
VSX-820_PWXCN_En.book 4 ページ
2010年4月2日 金曜日 午後1時30分
Thank you for buying this Pioneer product. Please read through these operating instructions so you
will know how to operate your model properly. After you have finished reading the instructions, put
them away in a safe place for future reference.
Contents
Flow of settings on the receiver . . 6
01 Before you start
Checking what’s in the box . . . . . . . . . . . . . . .
Loading the batteries . . . . . . . . . . . . . . . . . . .
Installing the receiver . . . . . . . . . . . . . . . . . . .
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
8
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating range of remote control . . . . . . . 10
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote control . . . . . . . . . . . . . . . . . . . . . . . 13
03 Connecting your equipment
4
En
Before setting up. . . . . . . . . . . . . . . . . . . . . . 29
Changing the TV format setting . . . . . . . . . 29
Automatically setting up for surround
sound (MCACC) . . . . . . . . . . . . . . . . . . . . . . 29
Other problems when using the Auto
MCACC Setup. . . . . . . . . . . . . . . . . . . . . . . 31
05 Listening to your system
02 Controls and displays
Placing the speakers. . . . . . . . . . . . . . . . . . .
Hints on the speaker placement . . . . . . . . .
Connecting the speakers . . . . . . . . . . . . . . .
Connect the surround back or front
height speakers . . . . . . . . . . . . . . . . . . . . .
Switching the speaker system . . . . . . . . . .
Making cable connections . . . . . . . . . . . . . .
HDMI cables . . . . . . . . . . . . . . . . . . . . . . .
About HDMI . . . . . . . . . . . . . . . . . . . . . . . .
Analog audio cables . . . . . . . . . . . . . . . . . .
Digital audio cables . . . . . . . . . . . . . . . . . .
Video cables . . . . . . . . . . . . . . . . . . . . . . . .
About video outputs connection . . . . . . . . . .
Connecting a TV and playback components . .
Connecting using HDMI. . . . . . . . . . . . . . .
Connecting your component with no
HDMI terminal . . . . . . . . . . . . . . . . . . . . . .
Connecting a satellite receiver or other
digital set-top box . . . . . . . . . . . . . . . . . . . . .
Connecting an HDD/DVD recorder, VCR
and other video sources . . . . . . . . . . . . . . . .
Using the component video jacks . . . . . . . . .
Connecting other audio components . . . . . .
Connecting antennas . . . . . . . . . . . . . . . . . .
Using external antennas. . . . . . . . . . . . . . .
Connecting to the front panel video
terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plugging in the receiver . . . . . . . . . . . . . . . .
04 Basic Setup
16
17
18
19
20
20
20
21
21
21
21
22
23
23
24
25
25
26
26
27
27
28
28
Basic playback . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting the audio input signal . . . . . . . . . 33
Auto playback . . . . . . . . . . . . . . . . . . . . . . . . 33
Listening in surround sound . . . . . . . . . . . . . 34
Using the Advanced surround effects . . . . . 35
Listening in stereo . . . . . . . . . . . . . . . . . . . . . 35
Using Front Stage Surround Advance . . . . . . 36
Using Stream Direct . . . . . . . . . . . . . . . . . . . 36
Using the Sound Retriever. . . . . . . . . . . . . . . 36
Better sound using Phase Control. . . . . . . . . 37
Listening with Acoustic Calibration EQ . . . . . 38
Using surround back channel processing . . . 38
Setting the Up Mix function. . . . . . . . . . . . . . 39
Setting the Audio options . . . . . . . . . . . . . . . 39
06 The System Setup menu
Using the System Setup menu . . . . . . . . . . . 42
Manual speaker setup . . . . . . . . . . . . . . . . . . 43
Speaker Setting . . . . . . . . . . . . . . . . . . . . . 43
Crossover Network . . . . . . . . . . . . . . . . . . . 45
Channel Level . . . . . . . . . . . . . . . . . . . . . . . 45
Speaker Distance . . . . . . . . . . . . . . . . . . . . 46
The Input Assign menu . . . . . . . . . . . . . . . . . 46
The Pre Out Setting . . . . . . . . . . . . . . . . . . . . 47
07 Using the tuner
Listening to the radio. . . . . . . . . . . . . . . . . . . 48
Improving FM sound. . . . . . . . . . . . . . . . . . 48
Saving station presets . . . . . . . . . . . . . . . . . . 48
Listening to station presets . . . . . . . . . . . . . 49
Naming preset stations. . . . . . . . . . . . . . . . 49
Changing the radio frequency step . . . . . . . . 49
VSX-820_PWXCN_En.book 5 ページ
2010年4月2日 金曜日 午後1時30分
08 Making recordings
Making an audio or a video recording . . . . . . 50
09 Controlling the rest of your system
Setting the remote to control other
components . . . . . . . . . . . . . . . . . . . . . . . . . 51
Selecting preset codes directly . . . . . . . . . . . 51
Clearing all the remote control settings. . . . . 52
Controls for TVs . . . . . . . . . . . . . . . . . . . . . . . 53
Controls for other components . . . . . . . . . . . 54
Preset Code List . . . . . . . . . . . . . . . . . . . . . . 55
10 Other connections
Connecting an iPod. . . . . . . . . . . . . . . . . . . . 64
Connecting your iPod to the receiver . . . . . 64
iPod playback . . . . . . . . . . . . . . . . . . . . . . . 65
Watching photos and video content . . . . . . 66
About iPod . . . . . . . . . . . . . . . . . . . . . . . . . 66
Connecting a USB device . . . . . . . . . . . . . . . 67
Connecting your USB device to the
receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Basic playback controls . . . . . . . . . . . . . . . 67
Compressed audio compatibility. . . . . . . . . 68
Bluetooth® ADAPTER for Wireless
Enjoyment of Music. . . . . . . . . . . . . . . . . . . . 69
Wireless music play . . . . . . . . . . . . . . . . . . 69
Connecting Optional Bluetooth
ADAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Pairing Bluetooth ADAPTER and
Bluetooth wireless technology device . . . . . 70
Listening to Music Contents of
Bluetooth wireless technology device
with Your System . . . . . . . . . . . . . . . . . . . . 71
11 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 72
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Important information regarding the
HDMI connection . . . . . . . . . . . . . . . . . . . . 76
iPod messages . . . . . . . . . . . . . . . . . . . . . . 76
USB messages . . . . . . . . . . . . . . . . . . . . . . 77
Resetting the main unit . . . . . . . . . . . . . . . . . 77
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 78
Cleaning the unit. . . . . . . . . . . . . . . . . . . . . . 78
5
En
VSX-820_PWXCN_En.book 6 ページ
2010年4月2日 金曜日 午後1時30分
Flow of settings on the receiver
The unit is a full-fledged AV receiver equipped
with an abundance of functions and terminals.
It can be used easily after following the
procedure below to make the connections and
settings.
The colors of the steps indicate the following:
Required setting item
Setting to be made as necessary

1 Before you start
• Checking what’s in the box (page 7)
• Loading the batteries (page 7)

Where you place the speakers will have a big
effect on the sound. Place your speakers as
shown below for the best surround sound effect.
• Placing the speakers (page 16)
• Connecting the speakers (page 18)
• Connect the surround back or front height
speakers (page 19)
(When connecting the front height speakers.)
The Input Assign menu (page 46)
(When using connections other than the
recommended connections.)
Listening
position
setup to set up your system
• Automatically setting up for surround sound
(MCACC) (page 29)

8 Basic playback (page 32)
*Surround Back
Right (SBR)
Surround
Left (SL)

9 Adjusting the sound as desired
*Surround Back
Left (SBL)
You can connect only one of either the surround back
speaker or the front height speaker.

3 Connecting the components
For surround sound, you’ll want to hook up
using a digital connection from the BD/DVD
player to the receiver.
• About video outputs connection (page 22)
• Connecting a TV and playback components
(page 23)
• Connecting antennas (page 27)
• Plugging in the receiver (page 28)

4 Power On
Make sure you’ve set the video input on your TV to
this receiver. Check the manual that came with
the TV if you don’t know how to do this.
En
6 The Pre Out Setting (page 47)

Center (C)
6

7 Use the on-screen automatic MCACC
Surround
Right (SR)
Front
Left (L)
to the region and environment in
which you live
• Changing the TV format setting (page 29)
• Changing the radio frequency step (page 49)
2 Connecting the speakers
*Front Height
Right (FHR)
*Front Height
Subwoofer (SW)
Left (FHL)
Front
Right (R)
5 Making the initial settings according

•
•
•
•
•
•
•
•
•
Using the various listening modes
Using the Sound Retriever (page 36)
Better sound using Phase Control (page 37)
Listening with Acoustic Calibration EQ
(page 38)
Using surround back channel processing
(page 38)
Setting the Up Mix function (page 39)
Setting the Audio options (page 39)
Selecting the audio input signal (page 33)
Manual speaker setup (page 43)

10 Making maximum use of the remote
control
• Setting the remote to control other
components (page 51)
VSX-820_PWXCN_En.book 7 ページ
2010年4月2日 金曜日 午後1時30分
Before you start
01
Chapter 1:
Before you start
Checking what’s in the box
Please check that you’ve received the following
supplied accessories:
• Setup microphone
• Remote control
• Dry cell batteries (AAA size IEC R03) x2
• AM loop antenna
• FM wire antenna
• iPod cable
• These operating instructions
Loading the batteries
CAUTION
Incorrect use of batteries may result in such
hazards as leakage and bursting. Observe the
following precautions:
• Never use new and old batteries together.
• Insert the plus and minus sides of the
batteries properly according to the marks
in the battery case.
• Batteries with the same shape may have
different voltages. Do not use different
batteries together.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
• Do not use or store batteries in direct
sunlight or other excessively hot place,
such as inside a car or near a heater. This
can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the
life or performance of batteries.
The batteries included with the unit are to
check initial operations; they may not last over
a long period. We recommend using alkaline
batteries that have a longer life.
(Symbol examples for batteries)
These symbols are only valid
in the European Union.
Pb
K058c_A1_En
7
En
VSX-820_PWXCN_En.book 8 ページ
01
2010年4月2日 金曜日 午後1時30分
Before you start
Installing the receiver
• When installing this unit, make sure to put
it on a level and stable surface.
Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that
gives off a magnetic field). This may interfere
with the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other
movement
– in places that are very dusty
– in places that have hot fumes or oils (such as
a kitchen)
Ventilation
When installing this unit, make sure to leave
space around the unit for ventilation to improve
heat dispersal (at least 40 cm at the top). If not
enough space is provided between the unit and
walls or other equipment, heat will build up
inside, interfering with performance and/or
causing malfunctions.
40 cm
Receiver
Slot and openings in the cabinet are provided
for ventilation and to protect the equipment
from overheating. To prevent fire hazard, do not
place anything directly on top of the unit, make
sure the openings are never blocked or covered
with items (such as newspapers, table-cloths
and curtains), and do not operate the
equipment on thick carpet or a bed.
8
En
VSX-820_PWXCN_En.book 9 ページ
2010年4月2日 金曜日 午後1時30分
Controls and displays
02
Chapter 2:
Controls and displays
Front panel
1
2
3
4
5
6
7
8
AUDIO/ VIDEO MULTI- CHANNEL RECEIVER
VSX-820
PHASE
CONTROL
STANDBY/ON
SPEAKERS
DIMMER
DISPLAY
BAND
TUNE
TUNER EDIT
PRESET
ENTER
MASTER
VOLUME
INPUT
SELECTOR
PHONES
LISTENING MODE
AUTO/DIRECT
STEREO/ALC
STANDARD
ADV SURROUND
VIDEO INPUT
iPod iPhone
DIRECT CONTROL
iPod
iPhone
USB
VIDEO
9
1
10
11
12
 STANDBY/ON
4 Remote sensor
Receives the signals from the remote control
(see Operating range of remote control on
page 10).
5
SPEAKERS
Use to change the speaker system (page 20).
DIMMER
Dims or brightens the display. The
brightness can be controlled in four steps.
AUDIO
13
R
MCACC
SETUP MIC
14
DISPLAY
Switches the display of this unit. The
listening mode, sound volume, Pre Out
setting or input name can be checked by
selecting an input source.1
2 INPUT SELECTOR dial
Selects an input source.
3 MCACC indicator
Lights when Acoustic Calibration EQ (page 38)
is on (Acoustic Calibration EQ is automatically
set to on after the Auto MCACC Setup
(page 29)).
L
6 Character display
See Display on page 11.
7
Tuner control buttons
BAND
Switches between AM, FM ST (stereo) and
FM MONO radio bands (page 48).
TUNE /
Used to find radio frequencies (page 48).
TUNER EDIT
Use with TUNE /, PRESET / and
ENTER to memorize and name stations for
recall (page 48, 49).
Note
1 The Pre Out setting may or may not be displayed, depending on the input source you have selected.
9
En
VSX-820_PWXCN_En.book 10 ページ
02
2010年4月2日 金曜日 午後1時30分
Controls and displays
PRESET /
Use to select preset radio stations
(page 49).
8
MASTER VOLUME dial
9 PHONES jack
Use to connect headphones. When the
headphones are connected, there is no sound
output from the speakers. The listening mode
when the sound is heard from the headphone
can be selected only from STEREO or ALC.
10 Listening mode buttons
AUTO/DIRECT
Switches between Auto surround mode
(Auto playback on page 33) and Stream
Direct playback. Stream Direct playback
bypasses the tone controls for the most
accurate reproduction of a source
(page 36).
STEREO/ALC
Switches between stereo playback, Auto
level control stereo mode (page 35) and
Front Stage Surround Advance modes
(page 36).
STANDARD
Press for Standard decoding and to switch
between the various 2 Pro Logic II, 2 Pro
Logic IIx, 2 Pro Logic IIz and NEO:6
options (page 32).
ADV SURROUND
Switches between the various surround
modes (page 35).
11 iPod iPhone DIRECT CONTROL
Change the receiver’s input to the iPod and
enable iPod operations on the iPod (page 66).
12 iPod iPhone/USB terminal
Use to connect your Apple iPod or USB mass
storage device as an audio source (page 64
and page 67).
13 AUDIO/VIDEO input
See Connecting to the front panel video terminal
on page 28.
10
En
14 MCACC SETUP MIC jack
Use to connect a microphone when
performing Auto MCACC setup.
Operating range of remote control
The remote control may not work properly if:
• There are obstacles between the remote
control and the receiver’s remote sensor.
• Direct sunlight or fluorescent light is
shining onto the remote sensor.
• The receiver is located near a device that is
emitting infrared rays.
• The receiver is operated simultaneously
with another infrared remote control unit.
30°
30°
7m
VSX-820_PWXCN_En.book 11 ページ
2010年4月2日 金曜日 午後1時30分
Controls and displays
02
Display
1
9
2
3
10
1 PHASE
Lights when the Phase Control is switched on
(page 37).
2 AUTO
Lights when the Auto Surround feature is
switched on (see Auto playback on page 33).
3 ST
Lights when a stereo FM broadcast is being
received in auto stereo mode.
4 TUNE
Lights when a normal broadcast channel is
being received.
5 Speaker indicators
Lights to indicate the current speaker system,
A and/or B (page 20).
6 Sleep timer indicator
Lights when the receiver is in sleep mode
(page 13).
7
Tuner preset indicators
PRESET
Shows when a preset radio station is
registered or called.
MEM
Blinks when a radio station is registered.
8 PRESET information or input signal
indicator
Shows the preset number of the tuner or the
input signal type, etc.
4
11
5
12
6
13
7
14 13
8
15
9 Character display
Displays various system information.
10 DTS indicators
DTS
Lights when a source with DTS encoded
audio signals is detected.
HD
Lights when a source with DTS-EXPRESS
or DTS-HD encoded audio signals is
detected.
ES
Lights to indicate DTS-ES decoding.
96/24
Lights when a source with DTS 96/24
encoded audio signals is detected.
NEO:6
When one of the NEO:6 modes of the
receiver is on, this lights to indicate NEO:6
processing (page 34).
11 Dolby Digital indicators
2D
Lights when a Dolby Digital encoded signal
is detected.
2D+
Lights when a source with Dolby Digital
Plus encoded audio signals is detected.
11
En
VSX-820_PWXCN_En.book 12 ページ
02
2010年4月2日 金曜日 午後1時30分
Controls and displays
2HD
Lights when a source with Dolby TrueHD
encoded audio signals is detected.
EX
Lights to indicate Dolby Digital EX
decoding.
2PLll(x)
Lights to indicate 2 Pro Logic II / 2 Pro
Logic IIx decoding. Light will go off during
2 Pro Logic IIz decoding (see Listening in
surround sound on page 34 for more on
this).
12 ADV.S.
Lights when one of the Advanced Surround
modes has been selected (see Using the
Advanced surround effects on page 35 for more
on this).
13 SIGNAL SELECT indicators
DIGITAL
Lights when a digital audio signal is
selected.
Blinks when a digital audio signal is
selected and selected audio input is not
provided.
HDMI
Lights when an HDMI signal is selected.
Blinks when an HDMI signal is selected
and selected HDMI input is not provided.
14 Up Mix/DIMMER indicator
Lights when the Up Mix function is set to ON
(see page 38). Also, lights when DIMMER is set
to off.
15 DIR.
Lights when the DIRECT or PURE DIRECT
mode is switched on (page 36).
12
En
VSX-820_PWXCN_En.book 13 ページ
2010年4月2日 金曜日 午後1時30分
Controls and displays
02
2  RECEIVER
Switches the receiver between standby and on.
Remote control
1
2
3
4
13
RECEIVER SLEEP
RECEIVER
TV
SOURCE CONTROL
INPUT SELECT
INPUT
BD
DVD
TV
DVR
CD
CD-R
14
4 INPUT SELECT
Use to select the input source.
CH
5
5 Input function buttons
Use to select the input source to this receiver.
This will enable you to control other
components with the remote control (see
Controlling the rest of your system on page 51).
ADAPTER iPod USB VIDEO
VOL
TUNER S.RETRIEVER SIGNAL SEL
6
7
8
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
AUDIO
PARAMETER
TUNE
TOP
MENU
10
ENTER
HOME
MENU
SETUP
T UN E
iPod CTRL
6 S.RETRIEVER
Press to restore CD quality sound to
compressed audio sources (page 36).
TUNER EDIT MASTER
VOLUME
TOOLS
MENU
PRESET
PRESET
9
15
BAND
BASS
HDD
1
TRE
DVD
VCR
2
3
SB CH CH SELECT
12
4
5
MIDNIGHT SPEAKERS
7
DIMMER
CLR
/ +10
6
LEV
8
9
0
LEV
ENTER
Listening mode buttons
MUTE
DTV/ TV
16
11
7 SIGNAL SEL
Press to select the audio input signal of the
component to play back (page 33).
8
RETURN
PTY SEARCH
3 RECEIVER
Switches the remote to control the receiver
(used to select the white commands above the
number buttons (MIDNIGHT, etc)). Also use
this button to set up surround sound (page 42)
or Audio parameters (page 39).
DISP
17
EQ
CH
PHASE
CH
SHIFT
18
RECEIVER
1 SLEEP
Press to change the amount of time before the
receiver switches into standby (30 min – 60
min – 90 min – Off). You can check the
remaining sleep time at any time by pressing
SLEEP once.
AUTO/DIRECT
Switches between Auto surround mode
(Auto playback on page 33) and Stream
Direct playback. Stream Direct playback
bypasses the tone controls for the most
accurate reproduction of a source
(page 36).
STEREO/A.L.C.
Switches between stereo playback, Auto
level control stereo mode (page 35) and
Front Stage Surround Advance modes
(page 36).
STANDARD
Press for Standard decoding and to switch
between 2 Pro Logic II options (page 34).
ADV SURR
Switches between the various surround
modes (page 35).
13
En
VSX-820_PWXCN_En.book 14 ページ
02
2010年4月2日 金曜日 午後1時30分
Controls and displays
Press BD first to access:
BD MENU*
Displays the disc menu of Blu-ray Discs.
9 System Setup and component control
buttons
The following button controls can be accessed
after you have selected the corresponding
input function button (BD, DVD, etc.).
Press RECEIVER first to access:
AUDIO PARAMETER
Use to access the Audio options (page 39).
SETUP
Press to access the System Setup menu
(page 42).
RETURN
Confirm and exit the current menu screen.
Press BD, DVD or DVR first to access:
10  (TUNE /, PRESET /),
ENTER
Use the arrow buttons when setting up your
surround sound system (page 42). Also used to
control BD/DVD menus/options.
Use the TUNE / buttons can be used to
find radio frequencies (page 48) and the
PRESET / buttons can be used to select
preset radio stations (page 49).
11 Component control buttons
The main buttons (, , etc.) are used to
control a component after you have selected it
using the input function buttons.
The controls above these buttons can be
accessed after you have selected the
corresponding input function button (BD,
DVD, DVR and CD). These buttons also
function as described below.
Press RECEIVER first to access:
TOP MENU
Displays the disc ‘top’ menu of a BD/DVD.
BASS –/+
Use to adjust Bass1
HOME MENU
Displays the HOME MENU screen.
TRE –/+
Use to adjust Treble1
RETURN
Confirm and exit the current menu screen.
MENU
Displays the TOOLS menu of Blu-ray Disc
player.
Press TUNER first to access:
TUNER EDIT
Memorizes/names stations for recall
(page 48 and 49).
BAND
Switches between AM, FM ST (stereo) and
FM MONO radio bands (page 48).
Press iPod USB first to access:
iPod CTRL
Switches between the iPod controls and
the receiver controls (page 66).
Press TV first to access:
DTV/TV
Switches between the DTV and analog TV
input modes for Pioneer TVs.
12 Number buttons and other component
controls
Use the number buttons to directly select a
radio frequency (page 48) or the tracks on a
CD, etc. There are other buttons that can be
accessed after the RECEIVER button is
pressed. (For example MIDNIGHT, etc.)
HDD*, DVD*, VCR*
These buttons switch between the hard
disk, DVD and VCR controls for HDD/DVD/
VCR recorders.
Note
1 The tone controls are disabled when the listening mode is set to DIRECT or PURE DIRECT.
14
En
VSX-820_PWXCN_En.book 15 ページ
2010年4月2日 金曜日 午後1時30分
Controls and displays
SB CH
Press to select ON, AUTO, OFF the
surround back channel.
CH SELECT
Press repeatedly to select a channel, then
use LEV +/– to adjust the level (page 45).
LEV +/–
Use to adjust the channel level.
EQ
Press to switch on/off Acoustic Calibration
EQ setting (page 38).
MIDNIGHT
Switches to Midnight or Loudness
listening (page 40).
02
VOL +/–
Use to adjust the volume on your TV.
15 MASTER VOLUME +/–
Use to set the listening volume.
16 MUTE
Mutes/unmutes the sound.
17 DISP
Switches the display of this unit. The listening
mode, sound volume, Pre Out setting or input
name can be checked by selecting an input
source.1
18 SHIFT
Press to access the ‘boxed’ commands (above
the buttons) on the remote. These buttons are
marked with an asterisk (* ) in this section.
SPEAKERS
Use to change the speaker system
(page 20).
PHASE
Press to switch on/off Phase Control
(page 37).
DIMMER
Dims or brightens the display. The
brightness can be controlled in four steps.
13  SOURCE
Press to turn on/off other components
connected to the receiver (see page 54 for
more on this).
14 TV CONTROL buttons
These buttons are dedicated to control the TV
assigned to the TV button. Thus if you only
have one TV to hook up to this system assign it
to the TV button (see page 53 for more on this).

Use to turn on/off the power of the TV.
INPUT
Use to select the TV input signal.
CH +/–
Use to select channels.
Note
1 The Pre Out setting may or may not be displayed, depending on the input source you have selected.
15
En
VSX-820_PWXCN_En.book 16 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Chapter 3:
Connecting your equipment
Placing the speakers
By connecting the left and right front speakers (L/R), the center speaker (C), the left and right
surround speakers (SL/SR), and the subwoofer (SW), a 5.1 ch surround system can be enjoyed.
Further, by using an external amplifier, you can connect the left and right surround back speakers
(SBL/SBR) and the left and right front height speaker (FHL/FHR) to boost your system up to a 7.1 ch
surround system.
• You can also connect one surround back speaker (SB) and enjoy a 6.1 ch surround system.
To achieve the best possible surround sound, install your speakers as shown below.
5.1 channel surround system:
6.1 channel surround
(Surround back) system: a
R
R
L
L
C
C
120
SW
120
SW
120
120
SR
SR
SL
SB
SL
7.1 channel surround
(Surround back) system: a
7.1 channel surround
(Front height) system: a
FHR
R
FHL
R
L
L
C
SW
90
C
SR
120
SW
90
120
SR
SBR
SL
SBL
60
SL
a. This layout is available only when the additional amplifier is connected to the unit and the surround back
or front height speakers are connected to the amplifier. For details, see Connect the surround back or front height
speakers on page 19.
16
En
VSX-820_PWXCN_En.book 17 ページ
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Hints on the speaker placement
Where you put your speakers in the room has a
big effect on the quality of the sound. The
following guidelines should help you to get the
best sound from your system.
• The subwoofer can be placed on the floor.
Ideally, the other speakers should be at
about ear-level when you’re listening to
them. Putting the speakers on the floor
(except the subwoofer), or mounting them
very high on a wall is not recommended.
• For the best stereo effect, place the front
speakers 2 m to 3 m apart, at equal
distance from the TV.
• If you’re going to place speakers around
your CRT TV, use shielded speakers or
place the speakers at a sufficient distance
from your CRT TV.
• If you’re using a center speaker, place the
front speakers at a wider angle. If not, place
them at a narrower angle.
• Place the center speaker above or below
the TV so that the sound of the center
channel is localized at the TV screen. Also,
make sure the center speaker does not
cross the line formed by the leading edge
of the front left and right speakers.
• It is best to angle the speakers towards the
listening position. The angle depends on
the size of the room. Use less of an angle
for bigger rooms.
• Surround and surround back speakers
should be positioned 60 cm to 90 cm
higher than your ears and titled slight
downward. Make sure the speakers don’t
face each other. For DVD-Audio, the
speakers should be more directly behind
the listener than for home theater
playback.
03
• If the surround speakers cannot be set
directly to the side of the listening position
with a 7.1-channel system, the surround
effect can be enhanced by turning off the
Up Mix function (see Setting the Up Mix
function on page 39).
• Try not to place the surround speakers
farther away from the listening position
than the front and center speakers. Doing
so can weaken the surround sound effect.
• Place the left and right front height
speakers at least one meter directly above
the left and right front speakers.
CAUTION
• Make sure that all speakers are securely
installed. This not only improves sound
quality, but also reduces the risk of
damage or injury resulting from speakers
being knocked over or falling in the event of
external shocks such as earthquakes.
Important
• To connect the surround back or front
height speakers, an additional amplifier is
required. Connect the additional amplifier
to the PRE OUT SURR BACK/FRONT
HEIGHT outputs of this unit and connect
the surround back or front height speakers
to the additional amplifier (see Connect the
surround back or front height speakers on
page 19).
The Pre Out setting must be set if the above
connections are performed. Select
SURR.BACK if the surround back speaker
is connected and HEIGHT if the front
height speaker is connected (If neither the
surround back speaker nor the front height
speaker is connected, either setting will
suffice) (see The Pre Out Setting on
page 47).
17
En
VSX-820_PWXCN_En.book 18 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Connecting the speakers
The receiver will work with just two stereo
speakers (the front speakers in the diagram)
but using at least three speakers is
recommended, and a complete setup is best
for surround sound.
You can use the speakers connected to the B
speaker terminals to listen to stereo playback
in another room. See Switching the speaker
system on page 20 for the listening options
with this setup.
Make sure you connect the speaker on the
right to the right (R) terminal and the speaker
on the left to the left (L) terminal. Also make
sure the positive and negative (+/–) terminals
on the receiver match those on the speakers.
You can use speakers with a normal
impedance between 6 Ω and 16 Ω.
However, note that only the front speakers are
set to a value between 12 Ω and 16 Ω if you
select SPAB in Switching the speaker system
on page 20.
Be sure to complete all connections before
connecting this unit to the AC power source.
Center speaker
Front speakers
L
Surround speakers
C
R
SL
SUBWOOFER
PRE OUT
SPEAKERS A
FRONT
R
L
CD-R/TAPE DVR/VCR
R SURROUND L
SR
CENTER
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
L
(Single)
VIDEO
DVR/VCR
OUT
IN
OUT
TV/SAT
IN
R
PRE OUT
CD
CD-R/TAPE DVR/VCR
L
E
IN
IN
TV/SAT
DVD
MONITOR OUT DVD IN
ANTENNA
FM
UNBAL
75
R
BD
PR
PB
SPEAKERS B
BD IN
Y
MONITOR
OUT
R
L
IN 2
(DVD)
L
IN
IN
R
AM
LOOP
E
AUDIO
COMPONENT VIDEO
IN 1
(BD)
ASSIGNABLE
1 2
Speaker system B
L
SW
Powered subwoofer
18
En
R
VSX-820_PWXCN_En.book 19 ページ
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Connect the surround back or front
height speakers
Bare wire connections
A-Speaker terminals:
1
Twist exposed wire strands together.
2
Loosen terminal and insert exposed wire.
3
Tighten terminal.
1
03
2
3
Connect the PRE OUT outputs of the unit and
additional amplifier to add a surround back or
front height speaker.
• If the surround back speaker or the front
height speaker is connected, set the Pre
Out setting (see The Pre Out Setting on
page 47).
Surround back or
front height speakers
SBL/FHL SBR/FHR
10 mm
Surround back or
front height
channel amplifier
B-Speaker terminals:
1
Twist exposed wire strands together.
ANALOG
2 Push open the tabs and insert exposed
wire.
3
INPUT
L
R
Release the tabs.
1
2
3
IN BD
SUBWOOFER
PRE OUT
CD-R/TAPE DVR/VCR
10 mm
ADAPTER
(OUTPUT 5 V 1
SURR BACK /
FRONT
HEIGHT
DVD
L
(Single)
OUT
R
PRE OUT
TV/SAT
CD
CAUTION
• These speaker terminals carry
HAZARDOUS LIVE voltage. To prevent
the risk of electric shock when connecting
or disconnecting the speaker cables,
disconnect the power cord before touching
any uninsulated parts.
• Make sure that all the bare speaker wire is
twisted together and inserted fully into the
speaker terminal. If any of the bare speaker
wire touches the back panel it may cause
the power to cut off as a safety measure.
CD-R/TAPE DVR/VCR
L
DVR/VCR
COAXIAL ASSIGNABLE
IN 1
(CD)
IN
TV/SAT
OPTICAL
OUT
IN
DVD
BD
L
IN 2
IN
IN 1
(CD-R/TAPE)
HDMI
M
ANTENNA
FM
UNBAL
75
R
ASSIGNABLE
1 2
IN
R
AM
LOOP
AUDIO
• You can use the additional amplifier on the
surround back channel pre-outs for a
single speaker as well. In this case plug the
amplifier into the left (L (Single)) terminal
only.
19
En
VSX-820_PWXCN_En.book 20 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Switching the speaker system
Three speaker system settings are possible
using the SPEAKERS button.
• Use the SPEAKERS button on the front
panel to select a speaker system setting.1
SPEAKERS
DIMMER
Making cable connections
Make sure not to bend the cables over the top
of this unit (as shown in the illustration). If this
happens, the magnetic field produced by the
transformers in this unit may cause a
humming noise from the speakers.
DISPLAY
Press repeatedly to choose a speaker system
option:
• SPA – Sound is output from the speakers
connected to the A speaker terminals and
PRE OUT SURR BACK/FRONT HEIGHT
(multichannel playback is possible).
• SPB – Sound is output from the two
speakers connected to speaker system B
(only stereo playback is possible).
• SPAB – Sound is output from speaker
system A, the two speakers in speaker
system B, and the subwoofer.
Multichannel sources are downmixed only
when the STEREO or ALC mode is selected
for stereo output from speaker systems A
and B. 2
• SP – No sound is output from the
speakers.
Important
• Before making or changing connections,
switch off the power and disconnect the
power cord from the AC outlet.
• Before unplugging the power cord, switch
the power into standby.
HDMI cables
Both video and sound signals can be transmitted
simultaneously with one cable. If connecting the
player and the TV via this receiver, for both
connections, use HDMI cables.3
HDMI cable
Be careful to connect the terminal in the
proper direction.
Note
1 The subwoofer output depends on the settings you made in Speaker Setting on page 43. However, if SPB is selected above,
no sound is heard from the subwoofer (the LFE channel is not downmixed).
2 You can use speakers with a normal impedance between 6 Ω and 16 Ω. However, be aware that only the front speakers are set
to a value between 12 Ω and 16 Ω when you select SPAB.
3 • Set the HDMI parameter in Setting the Audio options on page 39 to THRU (THROUGH) and set the input signal in Selecting
the audio input signal on page 33 to HDMI, if you want to hear HDMI audio output from your TV (no sound will be heard from
this receiver).
• If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that
some components (such as video game units) have resolutions that may not be displayed. In this case, use a (analog)
composite connection.
• When the video signal from the HDMI is 480i, 480p, 576i or 576p, Multi Ch PCM sound and HD sound cannot be received.
20
En
VSX-820_PWXCN_En.book 21 ページ
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
03
About HDMI
Analog audio cables
The HDMI connection transfers
uncompressed digital video, as well as almost
every kind of digital audio that the connected
component is compatible with, including DVDVideo, DVD-Audio, SACD, Dolby Digital Plus,
Dolby TrueHD, DTS-HD Master Audio (see
below for limitations), Video CD/Super VCD
and CD.
Use stereo RCA phono cables to connect
analog audio components. These cables are
typically red and white, and you should
connect the red plugs to R (right) terminals
and white plugs to L (left) terminals.
This receiver incorporates High-Definition
Multimedia Interface (HDMI®) technology.
This receiver supports the functions described
below through HDMI connections.1
• Digital transfer of uncompressed video
(contents protected by HDCP (1080p/24,
1080p/60, etc.))
• 3D signal transfer2
Analog audio cables
Right (red)
Left (white)
Digital audio cables
Commercially available coaxial digital audio
cables or optical cables should be used to
connect digital components to this receiver.4
• Deep Color signal transfer2
• x.v.Color signal transfer2
• Input of multi-channel linear PCM digital
audio signals (192 kHz or less) for up to 8
channels
• Input of the following digital audio formats:3
– Dolby Digital, Dolby Digital Plus, DTS,
High bitrate audio (Dolby TrueHD, DTS-HD
Master Audio), DVD-Audio, CD, SACD
(DSD signal), Video CD, Super VCD
HDMI, the HDMI Logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing, LLC in
the United States and other countries.
“x.v.Color” and x.v.Color logo are trademarks of
Sony Corporation.
Coaxial digital audio cable
Optical cable
Video cables
Standard RCA video cables
These cables are the most common type of
video connection and are used to connect to
the composite video terminals. The yellow
plugs distinguish them from cables for audio.
Standard RCA video cable
Note
1 • Use a High Speed HDMI® cable. If HDMI cable other than a High Speed HDMI® cable is used, it may not work properly.
• When an HDMI cable with a built-in equalizer is connected, it may not operate properly.
2 Signal transfer is only possible when connected to a compatible component.
3 • HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning playback.
• Turning on/off the device connected to this unit's HDMI OUT terminal during playback, or disconnecting/connecting the
HDMI cable during playback, may cause noise or interrupted audio.
4 • When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket.
• When storing optical cable, coil loosely. The cable may be damaged if bent around sharp corners.
• You can also use a standard RCA video cable for coaxial digital connections.
21
En
VSX-820_PWXCN_En.book 22 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Component video cables
Use component video cables to get the best
possible color reproduction of your video
source. The color signal of the TV is divided into
the luminance (Y) signal and the color (PB and
PR) signals and then output. In this way,
interference between the signals is avoided.
Component video cables
About video outputs connection
This receiver is not loaded with a video
converter. When you use component video
cables or HDMI cables for connecting to the
input device, the same cables should be used
for connecting to the TV.
The signals input from the analog (composite
and component) video inputs of this unit will
not be output from the HDMI OUT.
Green (Y)
Blue (PB)
Playback
component
Red (PR)
Terminal for connection with source device
PR
PB
COMPONENT VIDEO IN
HDMI IN
PR
HDMI OUT
Y
PB
VIDEO IN
Y
COMPONENT VIDEO MONITOR OUT
MONITOR OUT
Terminal for connection with TV monitor
The OSD will not
appear.
TV
Video signals can be output.
22
En
VSX-820_PWXCN_En.book 23 ページ
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
03
Connecting a TV and playback components
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray disc player, etc.), you can
connect it to this receiver using a commercially available HDMI cable.
• If the receiver is connected to a TV using an HDMI cable, the on-screen display (OSD) will not
be displayed. Be sure to use a standard RCA analog video cable to connect.12
IN BD
SUBWOOFER
PRE OUT
SPEAKERS A
FRONT
R
L
CD-R/TAPE DVR/VCR
This connection is
necessary in order to
see the OSD of the
unit on the TV.
DVD
R SURROUN
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
L
(Single)
VIDEO
DVR/VCR
OUT
IN
OUT
TV/SAT
IN
R
PRE OUT
TV/SAT
CD
CD-R/TAPE DVR/VCR
L
DVR/VCR
COAXIAL ASSIGNABLE
IN 1
(CD)
TV/SAT
DVD
PB
SPEAKERS B
BD IN
Y
MONITOR
OUT
R
L
IN 2
(DVD)
IN
IN 1
(CD-R/TAPE)
IN
R
ASSIGNABLE
1 2
AUDIO
AM
LOOP
IN 1
(BD)
ASSIGNABLE
1 2
COMPONENT VIDEO
This connection is
required in order to
listen to the sound of
the TV over the receiver.
2
VIDEO IN
BD
PR
L
IN 2
HDMI
MONITOR OUT DVD IN
ANTENNA
FM
UNBAL
75
R
OPTICAL
OUT
IN
IN
HDMI IN
HDMI OUT
OPTICAL
DIGITAL AUDIO OUT
R
L
ANALOG AUDIO OUT
Select one
HDMI/DVI-compatible TV
HDMI/DVI-compatible
Blu-ray disc player
Note
1 If you wish to see the OSD screen (for setup, etc.), switch the TV input to analog. (With HDMI input, the OSD will not be
displayed.)
2 In order to listen to the audio from the TV that is connected to this receiver using an optical cable, first, switch to the TV input,
then press SIGNAL SEL button repeatedly to choose the audio signal O1 (OPTICAL1) (see Selecting the audio input signal on
page 33).
23
En
VSX-820_PWXCN_En.book 24 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Connecting your component with no HDMI terminal
This diagram shows connections of a TV and DVD player (or other playback component) with no
HDMI terminal to the receiver.123
IN BD
SUBWOOFER
PRE OUT
SPEAKERS A
FRONT
R
L
CD-R/TAPE DVR/VCR
DVD
L
(Single)
VIDEO
DVR/VCR
OUT
IN
OUT
R SURROUN
3
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
TV/SAT
IN
R
PRE OUT
TV/SAT
CD
CD-R/TAPE DVR/VCR
L
COAXIAL ASSIGNABLE
DVR/VCR
IN 1
(CD)
TV/SAT
DVD
PR
BD
PB
MONITOR
MONITOR
OUT
R
L
IN 2
(DVD)
IN
IN 1
(CD-R/TAPE)
SPEAKERS B
BD IN
Y
L
IN 2
IN
AM
LOOP
R
ASSIGNABLE
1 2
HDMI
MONITOR OUT DVD IN
ANTENNA
FM
UNBAL
75
R
OPTICAL
OUT
IN
IN
COMPONENT VIDEO
AUDIO
IN 1
(BD)
ASSIGNABLE
1 2
2
VIDEO IN
1
R
OPTICAL
DIGITAL AUDIO OUT
R
L
ANALOG AUDIO OUT
L
ANALOG AUDIO OUT
COAXIAL
OPTICAL
DIGITAL AUDIO OUT
Select one
VIDEO OUT
Select one
TV
This connection is
required in order to
listen to the sound of
the TV over the receiver.
DVD player
Note
1 In order to listen to the audio from the TV that is connected to this receiver using an optical cable, first, switch to the TV input,
then press SIGNAL SEL button repeatedly to choose the audio signal O1 (OPTICAL1) (see Selecting the audio input signal on
page 33).
2 In order to listen to the audio from the DVD player that is connected to this receiver using an optical cable or a coaxial cable,
first, switch to the DVD input, then press SIGNAL SEL button repeatedly to choose the audio signal O2 (OPTICAL2) or C1
(COAXIAL1) (see Selecting the audio input signal on page 33).
3 If both TV and player has a component video jacks, you can connect these too. See Using the component video jacks on page 26
for more on this.
24
En
VSX-820_PWXCN_En.book 25 ページ
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
03
Connecting a satellite receiver
or other digital set-top box
Connecting an HDD/DVD recorder,
VCR and other video sources
Satellite and cable receivers, and terrestrial
digital TV tuners are all examples of so-called
‘set-top boxes’.12
This receiver has audio/video inputs and
outputs suitable for connecting analog or
digital video recorders, including HDD/DVD
recorders and VCRs.
• Only the signals that are input to the VIDEO
IN terminal can be output from the VIDEO
OUT terminal.
• Audio signals that are input through the
digital terminal will not be output from the
analog terminal.
SUBWOOFER
PRE OUT
CD-R/TAPE DVR/VCR
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
L
(Single)
VIDEO
DVR/VCR
OUT
IN
OUT
TV/SAT
IN
R
PRE OUT
CD
CD-R/TAPE DVR/VCR
L
COAXIAL ASSIGNABLE
IN 1
(CD)
IN
IN
DVD
TV/SAT
OPTICAL
MONITOR OUT DVD IN
ANTENNA
FM
UNBAL
75
R
BD
PR
PB
BD IN
Y
M
SUBWOOFER
PRE OUT
CD-R/TAPE DVR/VCR
L
IN 2
IN
IN 1
(CD-R/TAPE)
IN
R
ASSIGNABLE
1 2
AM
LOOP
L
(Single)
ASSIGNA
2
VIDEO
DVR/VCR
OUT
IN
OUT
TV/SAT
IN
R
COMPONENT VIDEO
AUDIO
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
PRE OUT
CD
CD-R/TAPE DVR/VCR
L
IN
COAXIAL ASSIGNABLE
IN 1
(CD)
2
TV/SAT
DVD
IN
R
ASSIGNABLE
1 2
R
L
ANALOG AUDIO OUT
Select one
PR
PB
BD IN
Y
VIDEO OUT
MONITOR
OUT
IN 2
(DVD)
IN
IN 1
(CD-R/TAPE)
OPTICAL
DIGITAL AUDIO OUT
MONITOR OUT DVD IN
ANTENNA
FM
UNBAL
75
BD
L
IN 2
1
IN
R
OPTICAL
AM
LOOP
COMPONENT VIDEO
AUDIO
IN 1
(BD)
ASSIGNABLE
1 2
1
STB
VIDEO IN
OPTICAL
DIGITAL
AUDIO OUT
R
PLAY
L
ANALOG AUDIO OUT
Select one
R REC L
ANALOG AUDIO IN
VIDEO OUT
DVR, VCR, etc.
Note
1 In order to listen to the audio from the source component that is connected to this receiver using an optical cable, first, switch
to the TV or DVR input, then press SIGNAL SEL button repeatedly to choose the audio signal O2 (OPTICAL2) (see Selecting the
audio input signal on page 33).
2 If the set-top box or video component also has an HDMI or a component video output, you can connect this too. See Connecting
using HDMI on page 23 or Using the component video jacks on page 26 for more on this.
25
En
VSX-820_PWXCN_En.book 26 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Using the component video jacks
Important
• If you connect any source component to the
receiver using a component video input, you
must also have your TV connected to this
receiver’s COMPONENT VIDEO OUT jacks.
Component video should deliver superior
picture quality when compared to composite
video. A further advantage (if your source and TV
are both compatible) is progressive-scan video,
which delivers a very stable, flicker-free picture.
See the manuals that came with your TV and
source component to check whether they are
compatible with progressive-scan video.
Connecting other audio
components
• If necessary, assign the component video
inputs to the input source you’ve connected.
This only needs to be done if you didn’t connect
according to the following defaults:
The number and kind of connections depends
on the kind of component you’re connecting.1
Follow the steps below to connect a CD-R, MD,
DAT, tape recorder or other audio component.2
• COMPONENT VIDEO IN 1 – BD
• COMPONENT VIDEO IN 2 – DVD
See The Input Assign menu on page 46 for
more on this.
SUBWOOFER
PRE OUT
CD-R/TAPE DVR/VCR
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
L
(Single)
VIDEO
DVR/VCR
OUT
IN
OUT
TV/SAT
IN
R
• For the audio connection, refer to
PRE OUT
CD
Connecting your component with no HDMI
terminal on page 24.
CD
IN
DVD
BD
PR
PB
BD IN
Y
M
L
IN
IN
IN
MONITOR OUT DVD IN
ANTENNA
R
TV/SAT
MONITOR OUT DVD IN
ANTENNA
FM
UNBAL
75
R
CD-R/TAPE DVR/VCR
L
DVD
PR
PB
FM
UNBAL
75
BD
SPE
BD IN
Y
MONITOR
OUT
IN 1
(CD-R/TAPE)
IN
R
ASSIGNABLE
1 2
AM
LOOP
ASSIGN
COMPONENT VIDEO
AUDIO
IN 2
(DVD)
L
IN
IN
R
SSIGNABLE
1 2
IN
TV/SAT
IN 2
PRE OUT
SSIGNABLE
COAXIAL ASSIGNABLE
IN 1
(CD)
OPTICAL
R
CD-R/TAPE DVR/VCR
L
AUDIO
AM
LOOP
COMPONENT VIDEO
IN 1
(BD)
ASSIGNABLE
1 2
2
PB
Y
PR
COMPONENT VIDEO IN
COAXIAL
OPTICAL
DIGITAL AUDIO OUT
PB
Y
PR
COMPONENT VIDEO OUT
TV
BD player
R PLAY L
ANALOG AUDIO OUT
R REC L
ANALOG AUDIO IN
Select one
CD-R, MD, DAT, Tape recorder, etc.
Note
1 Note that you must connect digital components to analog audio jacks if you want to record to/from digital components (like
an MD) to/from analog components.
2 In order to listen to the audio from the CD player that is connected to this receiver using an optical cable or a coaxial cable,
first, switch to the CD input, then press SIGNAL SEL button repeatedly to choose the audio signal O2 (OPTICAL2) or C1
(COAXIAL1) (see Selecting the audio input signal on page 33).
26
En
VSX-820_PWXCN_En.book 27 ページ
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
03
Using external antennas
Connecting antennas
Connect the AM loop antenna and the FM wire
antenna as shown below. To improve reception
and sound quality, connect external antennas
(see Using external antennas below).
fig. a
To improve FM reception
Connect an external FM antenna as shown
below.
fig. b
75 Ω coaxial cable
J-shaped plug
(not supplied)
2
4
ANTENNA
AM
LOOP
To improve AM reception
3
AM
LOOP
1
Connect a 5 m to 6 m length of vinyl-coated
wire to the AM antenna terminal without
disconnecting the supplied AM loop antenna.
For the best possible reception, suspend
horizontally outdoors.
1 Push open the tabs, then insert one wire
fully into each terminal, then release the tabs
to secure the AM antenna wires.
Outdoor
antenna
2 Fix the AM loop antenna to the attached
stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (fig. a) then
clip the loop onto the stand (fig. b).
3 Place the AM antenna on a flat surface
and in a direction giving the best reception.
ANTENNA
FM
UNBAL
75 Ω
AM
LOOP
Indoor antenna
(vinyl-coated wire)
5 m to 6 m
4 Connect the FM wire antenna into the FM
antenna socket.
For best results, extend the FM antenna fully
and fix to a wall or door frame. Don’t drape
loosely or leave coiled up.
27
En
VSX-820_PWXCN_En.book 28 ページ
03
2010年4月2日 金曜日 午後1時30分
Connecting your equipment
Connecting to the front panel
video terminal
Front video connections are accessed via the
front panel using the INPUT SELECTOR or
VIDEO button on the remote control. There are
standard audio/video jacks. Hook them up the
same way you made the rear panel
connections.
• Push down on the PUSH OPEN tab to
access the front video connections.
CONTROL
ON / OFF
MASTER
VOLUME
VIDEO INPUT
iPod
iPhone
USB
VIDEO
L
AUDIO
R
MCACC
SETUP MIC
This receiver
VIDEO
L
R
AUDIO/VIDEO OUTPUT
Video camera
(etc.)
Plugging in the receiver
Only plug in after you have connected all your
components to this receiver, including the
speakers.
CAUTION
• Handle the power cord by the plug part. Do
not pull out the plug by tugging the cord,
and never touch the power cord when your
hands are wet, as this could cause a short
circuit or electric shock. Do not place the
unit, a piece of furniture, or other object on
the power cord or pinch the cord in any
other way. Never make a knot in the cord or
tie it with other cables. The power cords
should be routed so that they are not likely
to be stepped on. A damaged power cord
can cause a fire or give you an electric
shock. Check the power cord once in a
while. If you find it damaged, ask your
nearest Pioneer authorized independent
service company for a replacement.
• The receiver should be disconnected by
removing the mains plug from the wall
socket when not in regular use, e.g., when
on vacation.
• Plug the AC power cord into a convenient
AC power outlet.
28
En
VSX-820_PWXCN_En.book 29 ページ
2010年4月2日 金曜日 午後1時30分
Basic Setup
04
Chapter 4:
Basic Setup
This receiver allows you to adjust the system
setup, and operate iPod/USB devices for
playback, using the on-screen display (OSD)
that is shown on the TV screen.
• The OSD will not appear if you have
connected using the HDMI output to your
TV. Use composite or component
connections for system setup.
First, follow the procedure below to make sure
that the OSD screen is displayed.
1
Switch on the receiver and your TV.
2 Switch the TV input to the input that
connects this receiver to the TV through the
corresponding composite or component
cable.
For example, if you connected this receiver to
the VIDEO jacks on your TV, make sure that the
VIDEO input is now selected.
3 Press RECEIVER on the remote control,
then press the SETUP button.
The System Setup menu of the OSD screen will
be displayed on the TV. If nothing appears on
the screen, try to change the TV format setting
on the receiver (see below).
Changing the TV format setting
If the OSD screen is not displayed correctly, it
may be that the TV system is set incorrectly for
your country or region.
1
Switch the receiver into standby.
The Auto Multi-Channel Acoustic Calibration
(MCACC) setup measures the acoustic
characteristics of your listening area, taking
into account ambient noise, speaker size and
distance, and tests for both channel delay and
channel level. After you have set up the
microphone provided with your system, the
receiver uses the information from a series of
test tones to optimize the speaker settings and
equalization for your particular room.
CAUTION
• The test tones used in the Auto MCACC
Setup are output at high volume.
Important
• The Auto MCACC Setup will overwrite any
existing speaker settings you’ve made.
• Before using the Auto MCACC Setup, the
iPod USB function should not be selected
as an input source.
• If you connected either the surround back
speaker or the front height speaker, make
sure that the Pre Out setting is correctly set
before performing the Auto MCACC Setup
(see page 47). (Here is an explanation
using the OSD screen for a surround back
speaker connection.)
AUDIO
PARAMETER
RECEIVER SLEEP
RECEIVER
TV
SOURCE CONTROL
INPUT SELECT
INPUT
BD
DVD
TV
TUNE
TOP
MENU
HOME
MENU
SETUP
iPod CTRL
ENTER
T UN E
TUNER EDIT MASTER
VOLUME
TOOLS
MENU
PRESET
2 While holding down the TUNE  button,
press and hold the  STANDBY/ON button
for about two seconds.
The display shows the new setting (PAL or
NTSC).
Automatically setting up for
surround sound (MCACC)
PRESET
Before setting up
BAND
RETURN
29
En
VSX-820_PWXCN_En.book 30 ページ
04
2010年4月2日 金曜日 午後1時30分
Basic Setup
1
Switch on the receiver and your TV.
2 Switch the TV input to the input that
connects this receiver to the TV through the
corresponding composite or component
cable.
3 Connect the microphone to the MCACC
SETUP MIC jack on the front panel.
Make sure there are no obstacles between the
speakers and the microphone.
CONTROL
5 Select ‘Auto MCACC’ from the System
Setup menu then press ENTER.2
System Setup
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
Return
Try to be as quiet as possible after pressing
ENTER. The system outputs a series of test
tones to establish the ambient noise level.
ON / OFF
MASTER
VOLUME
USB
L
AUDIO
Follow the instructions on-screen.
• Make sure the microphone is connected.
• Make sure the subwoofer is on and the
volume is turned up.
VIDEO INPUT
iPod
iPhone
VIDEO
6
R
MCACC
SETUP MIC
Microphone
Tripod
• See below for notes regarding background
noise and other possible interference.
7 Wait for the test tones to finish.
A progress report is displayed on-screen while
the receiver outputs test tones to determine the
speakers present in your setup. Try to be as
quiet as possible while it’s doing this.
1.Auto MCACC
If you have a tripod, use it to place the
microphone so that it’s about ear level at your
normal listening position. Otherwise, place the
microphone at ear level using a table or a chair.
4 Press RECEIVER on the remote control,
then press the SETUP button.
The System Setup menu appears on your TV.
Use /// and ENTER on the remote
control to navigate through the screens and
select menu items. Press RETURN to exit the
current menu.
Now Analyzing
Environment Check
Ambient Noise
Speaker YES/NO
Return
• For correct speaker settings, do not adjust
the volume during the test tones.
8 Confirm the speaker configuration.
The configuration shown on-screen should
reflect the actual speakers you have.
• Press SETUP at any time to exit the System
Setup menu.1
Note
1 The screensaver automatically starts after three minutes of inactivity. If you cancel the Auto MCACC Setup at any time, the
receiver automatically exits and no settings will be made.
2 MIC IN blinks when the microphone is not connected to MCACC SETUP MIC.
30
En
VSX-820_PWXCN_En.book 31 ページ
2010年4月2日 金曜日 午後1時30分
Basic Setup
04
• With error messages (such as Too much
ambient noise) select RETRY after
checking for ambient noise (see Other
problems when using the Auto MCACC
Setup on page 31).
1.Auto MCACC
10 The Auto MCACC Setup has finished!
You return to the System Setup menu.
The settings made in the Auto MCACC Setup
should give you excellent surround sound from
your system, but it is also possible to adjust
these settings manually using the System
Setup menu (starting on page 42).1
Check!
Front
Center
Surr
Surr. Back
Subwoofer
[ YES ]
[ YES ]
[ YES ]
[YESx2]
[ YES ]
10:Next
Other problems when using the Auto
MCACC Setup
OK
Return
If the speaker configuration displayed isn’t
correct, use / to select the speaker and
/ to change the setting. When you’re
finished, go to the next step.
If you see an error message (ERR) in the right
side column, there may be a problem with the
speaker connection. If selecting RETRY
doesn’t fix the problem, turn off the power and
check the speaker connections.
9 Make sure ‘OK’ is selected, then press
ENTER.
If the screen in step 7 is left untouched for 10
seconds and the ENTER button is not pressed
in step 8, the Auto MCACC setup will start
automatically as shown below.
If the room environment is not optimal for the
Auto MCACC Setup (too much background
noise, echo off the walls, obstacles blocking
the speakers from the microphone) the final
settings may be incorrect. Check for household
appliances (air conditioner, fridge, fan, etc.),
that may be affecting the environment and
switch them off if necessary. If there are any
instructions showing in the front panel display,
please follow them.
• Some older TVs may interfere with the
operation of the microphone. If this seems
to be happening, switch off the TV when
doing the Auto MCACC Setup.
A progress report is displayed on-screen while
the receiver outputs more test tones to
determine the optimum receiver settings for
channel level, speaker distance, and Acoustic
Calibration EQ.
1.Auto MCACC
Now Analyzing
Surround Analyzing
Speaker System
Speaker Distance
Channel Level
Acoustic Cal EQ
Return
Again, try to be as quiet as possible while this
is happening. It may take 1 to 3 minutes.
Note
1 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm will end up
with different size settings. You can correct the setting manually using the Speaker Setting on page 43.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be
accurate (taking delay and room characteristics into account) and generally does not need to be changed.
31
En
VSX-820_PWXCN_En.book 32 ページ
05
2010年4月2日 金曜日 午後1時30分
Listening to your system
Chapter 5:
Listening to your system
Important
• The listening modes and many features
described in this section may not be
available depending on the current source,
settings and status of the receiver.
Basic playback
Here are the basic instructions for playing a
source (such as a DVD disc) with your home
theater system.
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
RECEIVER SLEEP
RECEIVER
TV
SOURCE CONTROL
AUDIO
PARAMETER
INPUT SELECT
DVD
TV
DVR
CD
CD-R
ENTER
CH
HOME
MENU
SETUP
ADAPTER iPod USB VIDEO
T UN E
iPod CTRL
BAND
RETURN
PTY SEARCH
TUNER S.RETRIEVER SIGNAL SEL
TUNER EDIT MASTER
VOLUME
TOOLS
MENU
PRESET
BD
TUNE
TOP
MENU
PRESET
INPUT
DTV/ TV
MUTE
VOL
BASS
TRE
• Make sure the setup microphone is
disconnected.
1 Switch on your system components and
receiver.
Start by switching on the playback component
(for example a DVD player), your TV and
subwoofer (if you have one), then the receiver
(press  RECEIVER).
2 Switch the TV input to the input that
connects this receiver.
For example, if you connected this receiver to
the VIDEO jacks on your TV, make sure that the
VIDEO input is now selected.
3 Press input function buttons to select the
input function you want to play.
The input of the receiver will switch over, and
you will be able to operate other components
using the remote control.
• The input source can also be selected by
using INPUT SELECT buttons on the
remote control, or by using the front panel
INPUT SELECTOR dial.
4 Press AUTO/DIRECT to select ‘AUTO
SURROUND’ and start playback of the source.1
• If you selected the proper input source and
there is still no sound, press SIGNAL SEL
button to select the audio input signal for
playback (page 33).
If you’re playing a Dolby Digital or DTS
surround sound DVD disc, with a digital audio
connection, you should hear surround sound.
If you’re playing a stereo source or if the
connection is an analog audio connection, you
will only hear sound from the front left/right
speakers in the default listening mode.
It is possible to check on the front panel display
whether or not surround sound playback is
being performed properly.
Note
1 • You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to
output Dolby Digital, DTS and 88.2 kHz / 96 kHz PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert
the MPEG audio to PCM.
• Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the
receiver must be set to a multichannel listening mode if you want multichannel surround sound.
32
En
VSX-820_PWXCN_En.book 33 ページ
2010年4月2日 金曜日 午後1時30分
Listening to your system
05
When using a surround back speaker,
2D+PLIIx is displayed when playing Dolby
Digital 5.1-channel signals, and DTS+NEO:6 is
displayed when playing DTS 5.1-channel
signals.
• A – Selects the analog inputs.
When not using a surround back speaker, 2D
is displayed when playing Dolby Digital signals.
• HDMI – Selects an HDMI signal. H can be
selected for BD, DVD, TV/SAT or DVR/VCR
input. For other inputs, HDMI cannot be
selected.2
If the display does not correspond to the input
signal and listening mode, check the
connections and settings.
5 Use the volume control to adjust the
volume level.
Turn down the volume of your TV so that all
sound is coming from the speakers connected
to this receiver.
Selecting the audio input signal
The audio input signal can be selected for each
input source. Once it is set, the audio input that
was selected will be applied whenever you
select the input source using the input
function buttons.1
• DIGITAL – Selects the digital input. The
coaxial 1 input is selected for C1, and the
optical 1 or 2 audio input is selected for
O1 or O2.
When set to DIGITAL or HDMI, 2 lights when
a Dolby Digital signal is input, and DTS lights
when a DTS signal is input.
When the HDMI is selected, the A and
DIGITAL indicators are off (see page 12).
Auto playback
The simplest, most direct listening option is the
Auto Surround feature. With this, the receiver
automatically detects what kind of source
you’re playing and selects multichannel or
stereo playback as necessary.3
ADAPTER iPod USB VIDEO
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
TUNER S.RETRIEVER SIGNAL SEL
VOL
• Press SIGNAL SEL to select the audio
input signal corresponding to the source
component.
When DIGITAL (C1/O1/O2) or HDMI (H) is
selected and the selected audio input is not
provided, A (analog) is automatically selected.
Each press cycles through the following:
• While listening to a source, press
AUTO/DIRECT4 for auto playback of a
source.
Press repeatedly until AUTO SURROUND
shows briefly in the display (it will then show
the decoding or playback format). Check the
digital format indicators in the display to see
how the source is being processed.
Note
1 • When digital input (optical or coaxial) is selected, this receiver can only play back Dolby Digital, PCM (32 kHz to 96 kHz) and
DTS (including DTS 96 kHz / 24 bit) digital signal formats. The compatible signals via the HDMI terminals are: Dolby Digital,
DTS, SACD (DSD 2 ch), PCM (32 kHz to 192 kHz sampling frequencies), Dolby TrueHD, Dolby Digital Plus, DTS-EXPRESS, DTSHD Master Audio and DVD Audio (including 192 kHz). With other digital signal formats, set to A (analog).
• You may get digital noise when a LD or CD player compatible with DTS is playing an analog signal. To prevent noise, make
the proper digital connections (page 23) and set the signal input to C1/O1/O2 (DIGITAL).
• Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.
2 When the HDMI option in Setting the Audio options on page 39 is set to THRU, the sound will be heard through your TV, not
from this receiver.
3 Stereo surround (matrix) formats are decoded accordingly using NEO:6 CINEMA or DOLBY PLIIx MOVIE (see Listening in
surround sound above for more on these decoding formats).
4 For more options using this button, see Using Stream Direct on page 36.
33
En
VSX-820_PWXCN_En.book 34 ページ
05
2010年4月2日 金曜日 午後1時30分
Listening to your system
With two channel sources, you can select from:
Listening in surround sound
Using this receiver, you can listen to any source
in surround sound. However, the options
available will depend on your speaker setup and
the type of source you’re listening to.
The following modes provide basic surround
sound for stereo and multichannel sources.
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
• While listening to a source, press
STANDARD.
If the source is Dolby Digital, DTS, or Dolby
Surround encoded, the proper decoding
format will automatically be selected and
shows in the display.
When the surround back and front height
speaker are not connected.
With two channel sources, you can select from:
• DOLBY PLII MOVIE – Up to 5.1 channel
sound, especially suited to movie sources
• DOLBY PLII MUSIC1 – Up to 5.1 channel
sound, especially suited to music sources
• DOLBY PLII GAME – Up to 5.1 channel
sound, especially suited for video games
• NEO:6 CINEMA – Up to 5.1 channel sound,
especially suited to movie sources
• NEO:6 MUSIC – Up to 5.1 channel sound,
especially suited to music sources2
• DOLBY PRO LOGIC – 4.1 channel
surround sound
When the front height speaker is connected.
•
•
•
•
DOLBY PLII MOVIE – See above
DOLBY PLII MUSIC – See above
DOLBY PLII GAME – See above
DOLBY PLIIz HEIGHT – Up to 7.1 channel
sound3
• NEO:6 CINEMA – See above
• NEO:6 MUSIC – See above
• DOLBY PRO LOGIC – See above
• Straight Decode – Plays back without the
DOLBY PLII, DOLBY PLIIz HEIGHT and
NEO:6 effects.
With multichannel sources, you can select
from:
• DOLBY PLIIz HEIGHT – Up to 7.1 channel
sound3
• Straight Decode – Plays back without the
DOLBY PLIIz HEIGHT effects.
When the surround back speaker is
connected.4
If you connected surround back speakers, see
also Using surround back channel processing
on page 38.
With two channel sources, you can select from:
• DOLBY PLIIx MOVIE – Up to 7.1 channel
sound, especially suited to movie sources
• DOLBY PLIIx MUSIC – Up to 7.1 channel
sound, especially suited to music sources5
• DOLBY PLIIx GAME – Up to 7.1 channel
sound, especially suited to video games
• NEO:6 CINEMA – Up to 6.1 channel sound,
especially suited to movie sources
Note
1 When listening to 2-channel sources in DOLBY PLII MUSIC mode, there are three further parameters you can adjust:
C.WIDTH, DIMEN., and PNRM.. See Setting the Audio options on page 39 to adjust them.
2 When listening to 2-channel sources in NEO:6 CINEMA or NEO:6 MUSIC mode, you can also adjust the C.IMG effect (see
Setting the Audio options on page 39).
3 When listening to 2-channel sources in DOLBY PLIIz HEIGHT mode, you can also adjust the H.GAIN effect (see Setting the
Audio options on page 39).
4 • If surround back channel processing (page 38) is switched off, or the surround back speakers are set to NO, DOLBY PLIIx
becomes DOLBY PLII (5.1 channel sound).
• In modes that give 6.1 channel sound, the same signal is heard from both surround back speakers.
5 When listening to 2-channel sources in DOLBY PLIIx MUSIC mode, there are three further parameters you can adjust:
C.WIDTH, DIMEN., and PNRM.. See Setting the Audio options on page 39 to adjust them.
34
En
VSX-820_PWXCN_En.book 35 ページ
2010年4月2日 金曜日 午後1時30分
Listening to your system
05
• NEO:6 MUSIC – Up to 6.1 channel sound,
especially suited to music sources1
• CLASSICAL – Gives a large concert halltype sound.
• DOLBY PRO LOGIC – 4.1 channel
surround sound (sound from the surround
speakers is mono)
• ROCK/POP – Creates a live concert sound
for rock and/or pop music.
With multichannel sources, if you have
connected surround back speaker(s) and have
selected SB ON, you can select (according to
format):
• DOLBY PLIIx MOVIE – See above (only
available when you’re using two surround
back speakers)
• DOLBY PLIIx MUSIC – See above
• DOLBY DIGITAL EX – Creates surround
back channel sound for 5.1 channel
sources and provides pure decoding for
6.1 channel sources (like Dolby Digital
Surround EX)
• DTS-ES – Allows you to hear 6.1 channel
playback with DTS-ES encoded sources
• DTS NEO:6 – Allows you to hear 6.1 channel
playback with DTS encoded sources
• UNPLUGGED – Suitable for acoustic
music sources.
• EXT.STEREO – Gives multichannel sound to
a stereo source, using all of your speakers.
Listening in stereo
When you select STEREO you will hear the
source through just the front left and right
speakers (and possibly your subwoofer
depending on your speaker settings). Dolby
Digital and DTS multichannel sources are
downmixed to stereo.
In the Auto level control stereo mode (ALC),
this unit equalizes playback sound levels if
each sound level varies with the music source
recorded in a portable audio player.
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
Using the Advanced surround effects
The Advanced surround feature creates a
variety of surround effects. Try different modes
with various soundtracks to see which you like.
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
• Press ADV SURR repeatedly to select a
listening mode.
• ACTION – Designed for action movies with
dynamic soundtracks.
• DRAMA – Designed for movies with lots of
dialog.
• While listening to a source, press
STEREO/A.L.C. for stereo playback.
Press repeatedly to switch between:
• STEREO – The audio is heard with your
surround settings and you can still use the
Midnight, Loudness, Phase Control, Sound
Retriever and Tone functions.
• ALC – Listening in Auto level control stereo
mode.
• F.S.S.ADVANCE – See Using Front Stage
Surround Advance below for more on this.
• ENT.SHOW – Suitable for musical sources.
• ADVANCED GAME – Suitable for video
games.
• SPORTS – Suitable for sports programs.
Note
1 When listening to 2-channel sources in NEO:6 CINEMA or NEO:6 MUSIC mode, you can also adjust the C.IMG effect
(see Setting the Audio options on page 39).
35
En
VSX-820_PWXCN_En.book 36 ページ
05
2010年4月2日 金曜日 午後1時30分
Listening to your system
Using Front Stage Surround
Advance
The Front Stage Surround Advance function
allows you to create natural surround sound
effects using just the front speakers and the
subwoofer.
Using Stream Direct
Use the Stream Direct modes when you want
to hear the truest possible reproduction of a
source. All unnecessary signal processing is
bypassed.
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
BD MENU
AUTO/ STEREO/
DIRECT
A.L.C. STANDARD ADV SURR
• While listening to a source, press
STEREO/A.L.C. to select Front Stage
Surround Advance modes.
• STEREO – See Listening in stereo above for
more on this.
• ALC – See Listening in stereo above for
more on this.
• F.S.S.ADVANCE – Use to provide a rich
surround sound effect directed to the
center of where the front left and right
speakers sound projection area converges.
• While listening to a source, press AUTO/
DIRECT to select Stream Direct mode.
• AUTO SURROUND – See Auto playback on
page 33.
• DIRECT – Sources are heard according to
the settings made in the Surround Setup
(speaker setting, channel level, speaker
distance), as well as with dual mono
settings.1 You will hear sources according
to the number of channels in the signal.
• PURE DIRECT – Analog and PCM sources
are heard without any digital processing.
F.S.S.ADVANCE position
Front left
speaker
Front right
speaker
Using the Sound Retriever
When audio data is removed during the
compression process, sound quality often
suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
technology that helps bring CD quality sound
back to compressed 2-channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.2
ADAPTER iPod USB VIDEO
TUNER S.RETRIEVER SIGNAL SEL
VOL
• Press S.RETRIEVER to switch the sound
retriever on or off.
Note
1 In the DIRECT mode, Phase Control, Acoustic Calibration EQ, Sound Delay, Auto Delay, LFE Attenuate and Center image
functions are available.
2 The Sound Retriever is only applicable to 2-channel sources.
36
En
VSX-820_PWXCN_En.book 37 ページ
2010年4月2日 金曜日 午後1時30分
Listening to your system
Better sound using Phase Control
This receiver’s Phase Control feature uses
phase correction measures to make sure your
sound source arrives at the listening position in
phase, preventing unwanted distortion and/or
coloring of the sound (see illustration below).
During multichannel playback, LFE (LowFrequency Effects) signals as well as lowfrequency signals in each channel are
assigned to the subwoofer or other the
subwoofer and the most appropriate speaker.
At least in theory, however, this type of
processing involves a group delay that varies
with frequency, resulting in phase distortion
where the low-frequency sound is delayed or
muffled by the conflict with other channels.
With the Phase Control mode switched on, this
receiver can reproduce powerful bass sound
without deteriorating the quality of the original
sound (see illustration below).
05
P
H
A
S
E
C
O
N
T
R
O
L
O
F
F
?
Sound
source
O
N
Subwoofer
Front speaker
P
H
A
S
E
C
O
N
T
R
O
L
Listening
position
Front speaker
Sound
source
Listening
position
Subwoofer
Phase Control technology provides coherent
sound reproduction through the use of phase
matching1 for an optimal sound image at your
listening position. The default setting is on and
we recommend leaving Phase Control
switched on for all sound sources.
HDD
1
RECEIVER SLEEP
TV
SOURCE CONTROL
DVD
VCR
2
3
SB CH CH SELECT
4
5
MIDNIGHT SPEAKERS
RECEIVER
INPUT SELECT
7
INPUT
DIMMER
8
6
LEV
9
LEV
DISP
EQ
CH
PHASE
CH
SHIFT
• Press RECEIVER , then press PHASE to
switch the Phase Control on or off.
Note
1 Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are ‘in phase’, they crest
and trough together, resulting in increased amplitude, clarity and presence of the sound signal. If a crest of a wave meets a
trough (as shown in the upper section of the diagram above) then the sound will be ‘out of phase’ and an unreliable sound
image will be produced.
• If your subwoofer has a phase control switch, set it to the plus (+) sign (or 0°). However, the effect you can actually feel when
PHASE CONTROL is set to ON on this receiver depends on the type of your subwoofer. Set your subwoofer to maximize the
effect. It is also recommended you try changing the orientation or the place of your subwoofer.
• Set the built-in lowpass filter switch of your subwoofer to OFF. If this cannot be done on your subwoofer, set the cutoff
frequency to a higher value.
• If the speaker distance is not properly set, you may not have a maximized PHASE CONTROL effect.
• The PHASE CONTROL mode cannot be set to ON in the following cases:
– When the PURE DIRECT mode is switched on.
– When the headphones are connected.
37
En
VSX-820_PWXCN_En.book 38 ページ
05
2010年4月2日 金曜日 午後1時30分
Listening to your system
Listening with Acoustic
Calibration EQ
You can listen to sources using the Acoustic
Calibration Equalization set in Automatically
setting up for surround sound (MCACC) on
page 29. Refer to these pages for more on
Acoustic Calibration Equalization.
• With a 7.1-channel surround system, audio
signals that have undergone matrix
decoding processing through surround
back channel processing to which the Up
Mix function is added are output from the
surround back speakers.
HDD
1
RECEIVER SLEEP
RECEIVER
RECEIVER SLEEP
RECEIVER
TV
SOURCE CONTROL
HDD
DVD
VCR
1
2
3
SB CH CH SELECT
4
5
MIDNIGHT SPEAKERS
INPUT SELECT
7
INPUT
DIMMER
8
6
LEV
9
LEV
TV
SOURCE CONTROL
EQ
CH
PHASE
CH
SHIFT
• While listening to a source, press
RECEIVER , then press EQ to switch the
Acoustic Calibration EQ on or off.
The MCACC indicator on the front panel lights
when Acoustic Calibration EQ is active.1
Using surround back channel
processing
You can have the receiver automatically use 6.1
or 7.1 decoding for 6.1 encoded sources (for
example, Dolby Digital EX or DTS-ES), or you
can choose to always use 6.1 or 7.1 decoding
(for example, with 5.1 encoded material). With
5.1 encoded sources, a surround back channel
will be generated, but the material may sound
better in the 5.1 format for which it was
originally encoded (in which case, you can
simply switch surround back channel
processing off).
4
7
DIMMER
8
6
LEV
9
LEV
DISP
EQ
CH
PHASE
CH
SHIFT
• SB ON – Matrix decoding processing for
generating the surround back component
from the surround component is turned on.
• SB AUTO – Matrix decoding processing for
generating the surround back component
from the surround component is switched
automatically. Matrix decoding processing
is only performed when surround back
channel signals are detected in the input
signals.
• SB OFF – Matrix decoding processing for
generating the surround back component
from the surround component is turned
off.
Note
En
3
5
• Press RECEIVER , then press SB CH
repeatedly to cycle the surround back
channel options.
Each press cycles through the options as
follows:
1 You can’t use Acoustic Calibration EQ with Stream Direct mode and it has no effect with headphones.
38
VCR
2
MIDNIGHT SPEAKERS
INPUT SELECT
INPUT
DISP
DVD
SB CH CH SELECT
VSX-820_PWXCN_En.book 39 ページ
2010年4月2日 金曜日 午後1時30分
Listening to your system
05
Setting the Up Mix function
Setting the Audio options
In a 7.1-channel surround system with
surround speakers placed directly at the sides
of the listening position, the surround sound of
5.1-channel sources is heard from the side. The
Up Mix function mixes the sound of the
surround speakers with the surround back
speakers so that the surround sound is heard
from diagonally to the rear as it should be.1
There are a number of additional sound
settings you can make using the AUDIO
PARAMETER menu. The defaults, if not stated,
are listed in bold.
AUDIO
PARAMETER
RECEIVER SLEEP
RECEIVER
TV
SOURCE CONTROL
INPUT SELECT
INPUT
BD
DVD
TV
TUNE
TOP
MENU
HOME
MENU
SETUP
ENTER
T UN E
iPod CTRL
UP MIX OFF
R
SL
1
BAND
RETURN
UP MIX ON
L SW C
SR
SBL
TUNER EDIT MASTER
VOLUME
TOOLS
MENU
PRESET
• Depending on the positions of the speakers
and the sound source, in some cases it
may not be possible to achieve good
results. In this case, set the setting to OFF.
PRESET
• Using the Up Mix function is effective when
the speakers in the 7.1-channel surround
system are set up as recommended in the
example on page 16.
Important
• Note that if a setting doesn’t appear in the
AUDIO PARAMETER menu, it is
unavailable due to the current source,
settings and status of the receiver.
SBR
L SW C
R
SL
SR
SBL
SBR
Switch the receiver into standby.
2 While holding down the PRESET  on
the front panel, and hold the  STANDBY/
ON for about two seconds.
UP MIX: OFF appears and the Up Mix function
turns off. If you want to turn this function on,
perform steps 1 and 2 again.
1 Press RECEIVER on the remote control,
then press AUDIO PARAMETER button.
2 Use / to select the setting you want to
adjust.
Depending on the current status/mode of the
receiver, certain options may not be able to be
selected. Check the table below for notes on
this.
3 Use / to set it as necessary.
See the table below for the options available for
each setting.
4 Press RETURN to confirm and exit the
menu.
• When set to ON, the
(Up Mix) indicator
on the front panel lights.
Note
1 • Set to ON regardless of this setting when playing DTS-HD signals.
• May automatically be set to OFF even when set to ON, depending on the input signal and listening mode.
39
En
VSX-820_PWXCN_En.book 40 ページ
05
2010年4月2日 金曜日 午後1時30分
Listening to your system
Setting
What it does
EQ
(Acoustic Calibration
EQ)
Switches on/off the effect of Acoustic Calibration EQ.
S.DELAY
(Sound Delay)
Some monitors have a slight delay when showing video, so
the soundtrack will be slightly out of sync with the picture.
By adding a bit of delay, you can adjust the sound to match
the presentation of the video.
MIDNIGHTa
Allows you to hear effective surround sound of movies at
low volumes.
Option(s)
ON
OFF
LOUDNESSa
Used to get good bass and treble from music sources at
low volumes.
S.RTVb
(Sound Retriever)
When audio data is removed during the WMA/MP3c
compression process, sound quality often suffers from an
uneven sound image. The Sound Retriever feature employs
new DSP technology that helps bring CD quality sound
back to compressed 2-channel audio by restoring sound
pressure and smoothing jagged artifacts left over after
compression.
DUAL MONOd
Specifies how dual mono encoded Dolby Digital
soundtracks should be played.
0.0 to 9.0 (frames)
1 second = 25 frames
(PAL)/30 frames (NTSC)
Default: 0.0
M/L OFF
MIDNIGHT
LOUDNESS
OFF
ON
CH1 –
Channel 1 is heard only
CH2 –
Channel 2 is heard only
CH1 CH2 –
Both channels heard
from front speakers
DRC
(Dynamic Range
Control)
Adjusts the level of dynamic range for movie soundtracks
optimized for Dolby Digital, DTS, Dolby Digital Plus, Dolby
TrueHD, DTS-HD and DTS-HD Master Audio (you may
need to use this feature when listening to surround sound
at low volumes).
AUTOe
Some Dolby Digital and DTS audio sources include ultralow bass tones. Set the LFE attenuator as necessary to
prevent the ultra-low bass tones from distorting the sound
from the speakers.
The LFE is not limited when set to 0 dB, which is the
recommended value. When set to –15 dB, the LFE is
limited by the respective degree. When OFF is selected, no
sound is output from the LFE channel.
0 (0 dB)
MAX
MID
OFF
LFE ATT
(LFE Attenuate)
5 (–5 dB)
10 (–10 dB)
15 (–15 dB)
20 (–20 dB)
** (OFF)
G.f
SACD
(SACD Gain)
40
En
Brings out detail in SACDs by maximizing the dynamic
range (during digital processing).
0 (dB)
+6 (dB)
VSX-820_PWXCN_En.book 41 ページ
2010年4月2日 金曜日 午後1時30分
Listening to your system
05
Setting
What it does
HDMI
(HDMI Audio)
Specifies the routing of the HDMI audio signal out of this
receiver (amp) or through to a TV. When THRU is selected,
no sound is output from this receiver.
A.DLY
(Auto Delay)
This feature automatically corrects the audio-to-video delay
between components connected with an HDMI cable. The
audio delay time is set depending on the operational status
of the display connected with an HDMI cable. The video
delay time is automatically adjusted according to the audio
delay time.g
OFF
C.WIDTHh
Spreads the center channel between the front right and left
0 to 7
Default: 3
DIMEN.h
(Dimension)
Adjusts the surround sound balance from front to back,
making the sound more distant (minus settings), or more
forward (positive settings).
PNRM.h
Extends the front stereo image to include surround
speakers for a ‘wraparound’ effect.
speakers, making it sound wider (higher settings) or
(Center Width)
(Applicable only when narrower (lower settings).
using a center speaker)
(Panorama)
C.IMGi
Adjust the center image to create a wider stereo effect with
vocals. Adjust the effect from 0 (all center channel sent to
(Center image)
(Applicable only when front right and left speakers) to 10 (center channel sent to
using a center speaker) the center speaker only).
H.GAIN
(Height Gain)
Adjusts the output from the front height speaker when
listening in DOLBY PLIIz HEIGHT mode. If set to H, the
sound from the top will be more emphasized.
Option(s)
AMP
THRU
ON
–3 to +3
Default: 0
OFF
ON
0 to 10
Default: 3
(NEO:6 MUSIC),
10 (NEO:6 CINEMA)
L (Low)
M (Mid)
H (High)
a.
b.
c.
d.
e.
f.
g.
h.
i.
You can change the MIDNIGHT/LOUDNESS options at any time by using MIDNIGHT button.
You can change the Sound Retriever feature at any time by using S.RETRIEVER button.
WMA and MP3 playback available only via iPod/USB input.
This setting works only with dual mono encoded Dolby Digital and DTS soundtracks.
The initial set AUTO is only available for Dolby TrueHD signals. Select MAX or MID for signals other than
Dolby TrueHD.
You shouldn’t have any problems using this with most SACD discs, but if the sound distorts, it is best to
switch the gain setting back to 0 dB.
This feature is only available when the connected display supports the automatic audio/video synchronizing
capability (‘lip-sync’) for HDMI. If you find the automatically set delay time unsuitable, set A.DLY to OFF and
adjust the delay time manually. For more details about the lip-sync feature of your display, contact the
manufacturer directly.
Only available with 2-channel sources in DOLBY PLII MUSIC mode.
Only when listening to 2-channel sources in NEO:6 CINEMA and NEO:6 MUSIC mode.
41
En
VSX-820_PWXCN_En.book 42 ページ
06
2010年4月2日 金曜日 午後1時30分
The System Setup menu
Chapter 6:
The System Setup menu
4
Select the setting you want to adjust.
Using the System Setup menu
System Setup
The following section shows you how to make
detailed settings to specify how you’re using
the receiver, and also explains how to fine-tune
individual speaker system settings to your
liking.
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
Return
Important
• The OSD will not appear if you have
connected using the HDMI output to your
TV. Use component or composite
connections for system setup.
AUDIO
PARAMETER
INPUT SELECT
INPUT
BD
DVD
TV
TUNE
TOP
MENU
HOME
MENU
SETUP
iPod CTRL
ENTER
T UN E
TUNER EDIT MASTER
VOLUME
TOOLS
MENU
PRESET
RECEIVER
TV
SOURCE CONTROL
PRESET
RECEIVER SLEEP
BAND
• Auto MCACC – This is a quick and
effective automatic surround setup (see
Automatically setting up for surround
sound (MCACC) on page 29).
• Manual SP Setup – Specify the size,
number, distance and overall balance of
the speakers you’ve connected (see
Manual speaker setup on page 43).
• Input Assign – Specify what you’ve
connected to the component video inputs
(see The Input Assign menu on page 46).
RETURN
1 Switch on the receiver and your TV.
Use the  RECEIVER button to switch on.1
• Pre Out Setting – Specify how to use the
PRE OUT outputs (see The Pre Out Setting
on page 47).
2 Switch the TV input to the input that
connects this receiver to the TV through the
corresponding composite or component
cable.
3 Press RECEIVER on the remote control,
then press the SETUP button.2
The System Setup menu appears on your TV.
Use /// and ENTER on the remote
control to navigate through the screens and
select menu items. Press RETURN to confirm
and exit the current menu.
Note
1 If headphones are connected to the receiver, disconnect them.
2 • You can’t use the System Setup menu when the iPod/USB input is selected.
• Press SETUP at any time to exit the System Setup menu.
42
En
VSX-820_PWXCN_En.book 43 ページ
2010年4月2日 金曜日 午後1時30分
The System Setup menu
Manual speaker setup
This receiver allows you to make detailed
settings to optimize the surround sound
performance. You only need to make these
settings once (unless you change the
placement of your current speaker system or
add new speakers).
These settings are designed to fine-tune your
system, but if you’re satisfied with the settings
made in Automatically setting up for surround
sound (MCACC) on page 29, it isn’t necessary
to make all of these settings.
06
• Speaker Setting – Specify the size and
number of speakers you’ve connected (see
below).
• Crossover Network – Specify which
frequencies will be sent to the subwoofer
(page 45).
• Channel Level – Adjust the overall balance
of your speaker system (page 45).
• Speaker Distance – Specify the distance
of your speakers from the listening position
(page 46).
3 Make the adjustments necessary for
each setting, pressing RETURN to confirm
after each screen.
CAUTION
• The test tones used in the System Setup
are output at high volume.
Important
• Depending on the Pre Out setting, there
will be differences in the speaker items that
can be adjusted. The OSD display for these
operating instructions is an example of
when the Pre Out setting is set to Surr.
Back.
1 Select ‘Manual SP Setup’ then press
ENTER.
System Setup
Return
Use this setting to specify your speaker
configuration (size, number of speakers). It is a
good idea to make sure that the settings made
in Automatically setting up for surround sound
(MCACC) on page 29 are correct.
1 Select ‘Speaker Setting’ from the
Manual SP Setup menu.
2a.Speaker Setting
2.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Return
2.Manual SP Setup
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
Speaker Setting
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Return
2 Select the setting you want to adjust.
If you are doing this for the first time, you may
want to adjust these settings in order:
SMALL
Front
Center
[ SMALL ]
Surr
[ SMALL ]
Surr. Back [
NO
]
Subwoofer:
YES
Return
2 Choose the set of speakers that you
want to set then select a speaker size.
Use / to select the size (and number) of
each of the following speakers:
• Front – Select LARGE if your front
speakers reproduce bass frequencies
effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass
frequencies to the subwoofer.1
Note
1 If you select SMALL for the front speakers, the subwoofer will automatically be fixed to YES. Also, the center, surround,
surround back and front height speakers can’t be set to LARGE if the front speakers are set to SMALL. In this case, all bass
frequencies are sent to the subwoofer.
43
En
VSX-820_PWXCN_En.book 44 ページ
06
2010年4月2日 金曜日 午後1時30分
The System Setup menu
• Center – Select LARGE if your center
speaker reproduces bass frequencies
effectively, or select SMALL to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect a center
speaker, choose NO (the center channel is
sent to the other speakers).
• Front Height1 – Select LARGE if your front
height speakers reproduce bass
frequencies effectively. Select SMALL to
send bass frequencies to the other
speakers or subwoofer. If you didn’t
connect front height speakers choose NO.
• Surr – Select LARGE if your surround
speakers reproduce bass frequencies
effectively. Select SMALL to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect surround
speakers choose NO (the sound of the
surround channels is sent to the other
speakers).
• Surr. Back2 – Select the number of
surround back speakers you have (one, two
or none).3 Select LARGE if your surround
back speakers reproduce bass frequencies
effectively. Select SMALL to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect surround
back speakers choose NO.
• Subwoofer – LFE signals and bass
frequencies of channels set to SMALL are
output from the subwoofer when YES is
selected (see notes below). Choose the
PLUS setting if you want the subwoofer to
output bass sound continuously or you
want deeper bass (the bass frequencies
that would normally come out the front and
center speakers are also routed to the
subwoofer). If you did not connect a
subwoofer choose NO (the bass
frequencies are output from other
speakers).
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
• If you have a subwoofer and like lots of
bass, it may seem logical to select LARGE
for your front speakers and PLUS for the
subwoofer. This may not, however, yield the
best bass results. Depending on the
speaker placement of your room you may
actually experience a decrease in the
amount of bass due to low frequency
cancellations. In this case, try changing
the position or direction of speakers. If you
can’t get good results, listen to the bass
response with it set to PLUS and YES or the
front speakers set to LARGE and SMALL
alternatively and let your ears judge which
sounds best. If you’re having problems, the
easiest option is to route all the bass
sounds to the subwoofer by selecting
SMALL for the front speakers.
Note
1 • You can only adjust the Front Height setting when Pre Out Setting is set to Height.
• If the surround speakers are set to NO, the front height speakers will automatically be set to NO.
2 You can only adjust the Surr. Back setting when Pre Out Setting is set to Surr. Back.
3 • If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
• If you select one surround back speaker only, make sure that additional amplifier is hooked up to the PRE OUT L (Single)
terminal.
44
En
VSX-820_PWXCN_En.book 45 ページ
2010年4月2日 金曜日 午後1時30分
The System Setup menu
Crossover Network
06
2
• Default setting: 100Hz
This setting decides the cutoff between bass
sounds playing back from the speakers
selected as LARGE, or the subwoofer, and bass
sounds playing back from those selected as
SMALL. It also decides where the cutoff will be
for bass sounds in the LFE channel.1
1 Select ‘Crossover Network’ from the
Manual SP Setup menu.
Select a setup option.
• Manual – Move the test tone manually
from speaker to speaker and adjust
individual channel levels.
• Auto – Adjust channel levels as the test
tone moves from speaker to speaker
automatically.
3 Confirm your selected setup option.
The test tones will start after you press ENTER.
After the volume increases to the reference
level, test tones will be output.
2b.Crossover Network
2.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Frequency
2c.Channel Level
100Hz
Test Tone
[ Manual ]
Please Wait . . .20
Caution
Loud test tones
will be output.
Return
Return
 Return
2 Choose the frequency cutoff point.
Frequencies below the cutoff point will be sent
to the subwoofer (or LARGE speakers).
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
4 Adjust the level of each channel using
/.
If you selected Manual, use / to switch
speakers. The Auto setup will output test tones
in the order shown on-screen:
2c.Channel Level
Channel Level
Using the channel level settings, you can
adjust the overall balance of your speaker
system, an important factor when setting up a
home theater system.
1 Select ‘Channel Level’ from the Manual
SP Setup menu.
2c.Channel Level
2.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Return
Test Tone
Manual
Front L
Center
Front R
Surround R
Surr. Back R
Surr. Back L
Surround L
Subwoofer
[
[
[
[
[
[
[
0dB
0dB]
0dB]
0dB]
–––
]
–––
]
0dB]
0dB]
Return
Adjust the level of each speaker as the test tone
is emitted.2
5 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
ENTER:NextReturn
Note
1 For more on selecting the speaker sizes, see Speaker Setting on page 43.
2 • If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level
of each speaker to 75 dB SPL (C-weighting/slow reading).
• The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.
45
En
VSX-820_PWXCN_En.book 46 ページ
06
2010年4月2日 金曜日 午後1時30分
The System Setup menu
Tip
• You can change the channel levels at any
time by press RECEIVER , then press CH
SELECT and LEV +/– on the remote control.
You can also press CH SELECT and use /
 to select the channel, and then use /
 to adjust the channel levels.
The Input Assign menu
You only need to make settings in the Input
Assign menu if you didn’t hook up your
equipment according to the default settings for
the component video inputs.
• Default settings:
Component 1 – BD
Component 2 – DVD
Speaker Distance
For good sound depth and separation from
your system, you need to specify the distance
of your speakers from the listening position.
The receiver can then add the proper delay
needed for effective surround sound.
1 Select ‘Speaker Distance’ from the
Manual SP Setup menu.
2d.Speaker Distance
2.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Return
Front L
Center
Front R
Surround R
Surr. Back R
Surr. Back L
Surround L
Subwoofer
3.0
[
3.0
[
3.0
[
3.0
[ ––––
[ ––––
[
3.0
[
3.0
m
m ]
m ]
m ]
]
]
m ]
m ]
Return
2 Adjust the distance of each speaker
using /.
You can adjust the distance of each speaker in
0.1 m increments.
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Important
• If you connect any source component to
the receiver using a component video
input, you should also have your TV
connected to this receiver’s COMPONENT
VIDEO OUT output (down converting
component video is not possible after
assigning an input).
If you didn’t make component video
connections according to the defaults above,
you must assign the numbered input to the
component you’ve connected (or else you may
see the video signal of a different component).
For more on this, see Using the component
video jacks on page 26.
1 Press RECEIVER on the remote control,
then press the SETUP button.
An on-screen display (OSD) appears on your
TV. Use /// and ENTER on the remote
control to navigate through the screens and
select menu items. Press RETURN to confirm
and exit the current menu.
System Setup
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
Return
46
En
VSX-820_PWXCN_En.book 47 ページ
2010年4月2日 金曜日 午後1時30分
The System Setup menu
06
2 Select ‘Input Assign’ from the System
Setup menu.
Specify either using the surround back speaker
or the front height speaker connection with the
PRE OUT outputs. An additional amplifier is
required for the speaker connection.
System Setup
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
• Default setting: Surr. Back
Return
3 Select ‘Component Input’ from the
Input Assign menu.
3a.Component Input
3.Input Assign
Component–1
Component–2
a.Component Input
The Pre Out Setting
[
BD
DVD
Return
]
1 Press RECEIVER on the remote control,
then press the SETUP button.
An on-screen display (OSD) appears on your
TV. Use /// and ENTER on the remote
control to navigate through the screens and
select menu items. Press RETURN to confirm
and exit the current menu.
System Setup
Return
4 Select the number of the component
video input to which you’ve connected
your video component.
The numbers correspond with the numbers
beside the inputs on the rear of the receiver.
5 Select the component that corresponds
with the one you connected to that input.
Select between BD, DVD, TV, DVR or OFF.
• Use / and ENTER to do this.
• If you assign a component input to a
certain function, any component inputs
previously assigned to that function will
automatically be switched off.
• Make sure you have connected the audio
from the component to the corresponding
inputs on the rear of the receiver.
6 When you’re finished, press RETURN.
You return to the Input Assign menu.
• For the assignment of the digital signal
inputs, see Selecting the audio input signal
on page 33.
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
Return
2 Select ‘Pre Out Setting’ from the System
Setup menu.
System Setup
4.Pre Out Setting
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
Return
Pre Out
Surr. Back
Return
3 Select which speaker to connect to the
PRE OUT outputs using /.
• Surr. Back – Connect the surround back
speaker.
• Height – Connect the front height speaker.
4 When you’re finished, press RETURN.
You return to the System Setup menu.
47
En
VSX-820_PWXCN_En.book 48 ページ
07
2010年4月2日 金曜日 午後1時30分
Using the tuner
Chapter 7:
Using the tuner
Listening to the radio
The following steps show you how to tune in to
FM and AM radio broadcasts using the
automatic (search) and manual (step) tuning
functions. Once you are tuned to a station you
can memorize the frequency for recall later—
see Saving station presets below for more on
how to do this.
PARAMETER
CD
CD-R
CH
TUNER S.RETRIEVER SIGNAL SEL
ENTER
Improving FM sound
If the TUNE or ST indicators don’t light when
tuning to an FM station because the signal is
weak, press the BAND button to select FM
MONO and set the receiver to the mono
reception mode. This should improve the
sound quality and allow you to enjoy the
broadcast.
VOL
HOME
MENU
SETUP
iPod CTRL
1
MENU
PRESET
ADAPTER iPod USB VIDEO
VOLUME
TOOLS
TUNE
TOP
MENU
PRESET
DVR
High speed tuning
Press and hold TUNE / for high speed
tuning. Release the button at the frequency
you want.
T UN E
BAND
RETURN
Press TUNER to select the tuner.
2 Use BAND to change to BAND (FM or
AM), if necessary.
Each press switches the band between FM
(stereo or mono) and AM.
Saving station presets
If you often listen to a particular radio station,
it’s convenient to have the receiver store the
frequency for easy recall whenever you want to
listen to that station. This saves the effort of
manually tuning in each time. This unit can
memorize up to 30 stations.1
3 Tune to a station.
There are three ways to do this:
Manual tuning
To change the frequency one step at a
time, press TUNE /.
RECEIVER
PRESET
RECEIVER SLEEP
TUNE
TOP
MENU
INPUT SELECT
TUNER EDIT MASTER
VOLUME
TOOLS
MENU
PRESET
Automatic tuning
To search for stations in the currently
selected band, press and hold TUNE /
for about a second. The receiver will start
searching for the next station, stopping
when it has found one. Repeat to search for
other stations.
AUDIO
PARAMETER
TV
SOURCE CONTROL
ENTER
INPUT
BD
DVD
TV
DVR
CD
CD-R
HOME
MENU
SETUP
T UN E
iPod CTRL
CH
DTV/ TV
BASS
ADAPTER iPod USB VIDEO
TUNER S.RETRIEVER SIGNAL SEL
BAND
RETURN
PTY SEARCH
MUTE
TRE
VOL
HDD
DVD
VCR
1
2
3
DISP
Note
1 • If the receiver is left disconnected from the AC power outlet for over a month, the station memories will be lost and will have
to be reprogrammed.
• Stations are stored in stereo. When the station is stored in the FM MONO mode, it shows as ST when recalled.
48
En
VSX-820_PWXCN_En.book 49 ページ
2010年4月2日 金曜日 午後1時30分
Using the tuner
07
1 Tune to a station you want to memorize.
See Listening to the radio on page 48 for more
on this.
Tip
• To erase a station name, follow steps 1 and
2, and press ENTER while the display is
blank. Press TUNER EDIT while the display
is blank, to keep the previous name.
2 Press TUNER EDIT.
The display shows PRESET, then a blinking
MEM and station preset.
• Once you have named a station preset,
Press DISP to show the name. When you
want to return to the frequency display,
press DISP several times to show the
frequency.
3 Press PRESET / to select the station
preset you want.
You can also use the number buttons.
4 Press ENTER.
After pressing ENTER, the preset number stop
blinking and the receiver stores the station.
Listening to station presets
You will need to have some presets stored to do
this. See Saving station presets on page 48 if
you haven’t done this already.
• Press PRESET / to select the station
preset you want.
• You can also use the number buttons on
the remote control to recall the station
preset.
Naming preset stations
For easier identification, you can name all of
your preset stations.
Changing the radio frequency
step
If you find that you can’t tune into stations
successfully, the frequency step may not be
suitable for your country/region. Here’s how to
switch the setting:
1
Switch the receiver into standby.
2 While holding down the TUNE  button,
press and hold the  STANDBY/ON button
for about two seconds.
• The channel tuning step alternates
between 10K STEP and 9K STEP each time
you do this.
1 Choose the station preset you want to
name.
See Listening to station presets above for how
to do this.
2 Press TUNER EDIT twice.
The cursor at the first character position is
blinking on the display.
3 Input the name you want.
Choose a name up to eight characters long.
• Use the PRESET / buttons to select
character position.
• Use the TUNE / buttons to select
characters.
• The name is stored when ENTER is
pressed.
49
En
VSX-820_PWXCN_En.book 50 ページ
08
2010年4月2日 金曜日 午後1時30分
Making recordings
Chapter 8:
Making recordings
Making an audio or a video
recording
You can make an audio or a video recording
from the built-in tuner, or from an audio or
video source connected to the receiver (such
as a CD player or TV).
Only video signals that were input to this
receiver through a composite video cable or
analog audio inputs can be recorded. Signals
that were input through an HDMI cable,
component video cable or digital audio cable
(see Connecting other audio components on
page 26 for more on connections).
BD
DVD
TV
DVR
CD
CD-R
CH
ADAPTER iPod USB VIDEO
TUNER S.RETRIEVER SIGNAL SEL
2 Select the audio input signal (if necessary).
Press SIGNAL SEL button and select the
analog inputs (A) for the source component of
which you want to record (see page 33 for more
on this).
3 Prepare the source you want to record.
Tune to the radio station, load the CD, video,
DVD etc.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the
recording device and set the recording levels.
Refer to the instructions that came with the
recorder if you are unsure how to do this. Most
video recorders set the audio recording level
automatically—check the component’s
instruction manual if you’re unsure.
5 Start recording, then start playback of the
source component.1
VOL
1 Press input function buttons to select the
input function you want to record.
The input of the receiver will switch over, and
you will be able to operate other components
using the remote control.
• The input source can also be selected by
using INPUT SELECT buttons on the
remote control, or by using the front panel
INPUT SELECTOR dial.
Note
1 • The receiver’s volume, balance, tone (bass, treble, loudness), and surround effects have no effect on the recorded signal.
• Some video sources are copy-protected. These cannot be recorded.
50
En
VSX-820_PWXCN_En.book 51 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
09
Chapter 9:
Controlling the rest of your
system
Setting the remote to control
other components
Selecting preset codes directly
RECEIVER
INPUT SELECT
INPUT
Most components can be assigned to one of
the input function buttons using the
component’s manufacturer preset code stored
in the remote.
BD
DVD
Note
• You can cancel or exit any of the steps by
pressing RECEIVER .
• After one minute of inactivity, the remote
automatically exits the operation.
1
DVD
VCR
2
3
SB CH CH SELECT
DVR
CD
CD-R
CH
4
5
MIDNIGHT SPEAKERS
7
ADAPTER iPod USB VIDEO
However, please note that there are cases
where only certain functions may be
controllable after assigning the proper preset
code, or the codes for the manufacturer in the
remote control will not work for the model that
you are using.1
HDD
TV
DIMMER
CLR
/ +10
6
LEV
8
9
0
LEV
ENTER
DISP
EQ
CH
PHASE
CH
SHIFT
1 While pressing the RECEIVER button,
press and hold the ‘1’ button for three
seconds.
2 Press the input function button for the
component you want to control.
The component can be assigned to the BD,
DVD, TV, DVR, CD, CD-R or VIDEO button.
• When assigning preset codes to TV
CONTROL, press INPUT here.
3 Use the number buttons to enter the
preset code.
You can find the preset codes on page 55.
If the correct code has been input the power of
the component being input will turn on or off.
The power of the component being input will
only turn on or off if that component is able to
be turned on directly by remote control.
4 Repeat steps 2 through 3 to try a different
code, or to enter a code for another
component you want to control.
5
When you’re done, press RECEIVER .
Note
1 TV CONTROL buttons are only dedicated to control the TV (for example, codes for TV, CATV, Satellite TV or DTV).
51
En
VSX-820_PWXCN_En.book 52 ページ
09
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Clearing all the remote control
settings
You can clear all presets and restore the factory
default settings.
• While pressing the RECEIVER button,
press and hold the ‘0’ button for three
seconds.
Default preset codes
52
En
Input function
button
Preset code
BD
2255
DVD
2256
TV
0291
DVR
2257
VIDEO
1053
CD
5000
CD-R
5001
TV CONTROL
0291
VSX-820_PWXCN_En.book 53 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
09
Controls for TVs
This remote control can control components after entering the proper codes or teaching the
receiver the commands (see Controlling the rest of your system on page 51 for more on this). Use
the input function buttons to select the component.
• The TV CONTROL buttons on the remote control are dedicated to control the TV assigned to
the TV CONTROL INPUT button.
Button(s)
Function
TV CONTROL  Switches the DTV on or off.
Components
DTV
Switches the TV or CATV between standby and on.
Cable TV/Satellite TV/TV
TV CONTROL
INPUT
Switches the TV input. (Not possible with all models.)
TV
TV CONTROL
CH +/–
Selects channels.
Cable TV/Satellite TV/TV/DTV
TV CONTROL
VOL +/–
Adjust the TV volume.
Cable TV/Satellite TV/TV/DTV
 SOURCE
Press to switch the component assigned to the TV
button on or off.
Cable TV/Satellite TV/TV/DTV
DTV/TV
Switches between the DTV and analog TV input modes TV/DTV
for Pioneer TVs.
TOP MENU
Switches TEXT ON/OFF for TVs.
TV
HOME MENU
Use as the GUIDE button for navigating.
Cable TV/Satellite TV/TV/DTV
RETURN
Use to select closed captioning with DTV.
DTV
Number
buttons
Use to select a specific TV channel.
Cable TV/Satellite TV/TV/DTV
ENTER
Use to enter a channel.
Cable TV/Satellite TV/TV/DTV
MENU
Press to display the DTV menu.
DTV
Select the menu screen.
Cable TV/Satellite TV/TV
 &
ENTER
Press to select or adjust and navigate items on the
menu screen.
Cable TV/Satellite TV/TV/DTV
CH +/–
Selects channels.
Cable TV/Satellite TV/TV/DTV
53
En
VSX-820_PWXCN_En.book 54 ページ
09
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Controls for other components
This remote control can control these components (BD, DVD, CD, DVR (BDR), VCR, CD-R) after
entering the proper codes or teaching the receiver the commands (see Controlling the rest of your
system on page 51 for more on this). Use the input function buttons to select the component.
Button(s)
Function
 SOURCE Press to switch the component between standby and on.

Press to return to the start of the current track.
Repeated presses skips to the start of previous tracks.

Press to advance to the start of the next track.
Repeated presses skips to the start of following tracks.

Pause playback or recording.

Start playback.

Hold down for fast forward playback.

Hold down for fast reverse playback.

Stops playback (on some models, pressing this when the
disc is already stopped will cause the disc tray to open).
Number
buttons
Use to enter a title/chapter/track number.
DISP
Press to display information.
Components
Blu-ray disc player, DVD
player, CD player, DVR
(BDR), VCR, CD-R
TOP MENU Displays the disc ‘top’ menu of a BD/DVD player.
MENU
Displays menus for the current BD/DVD or DVR you are
using.
,
ENTER &
RETURN
Navigates BD/DVD menu/options.
HOME
MENU
Displays the HOME MENU.
CH +/–
Selects channels.
DVR, VCR
HDD
Switches to the hard disk controls when using an HDD/ HDD/DVD/VCR recorder
(SHIFT + 1) DVD recorder.
DVD
Switches to the DVD controls when using an HDD/DVD HDD/DVD/VCR recorder
(SHIFT + 2) recorder.
VCR
Switches to the VCR controls when using an HDD/DVD/ HDD/DVD/VCR recorder
(SHIFT + 3) VCR recorder.
54
En
VSX-820_PWXCN_En.book 55 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
09
Preset Code List
You should have no problem controlling a component if you find the manufacturer in this list, but
please note that there are cases where codes for the manufacturer in the list will not work for the
model that you are using. There are also cases where only certain functions may be controllable
after assigning the proper preset code.
example:
TV
Pioneer 0291
Important
Category
Preset code
Manufacturer
• We do not guarantee the operations of all
the manufacturers and devices listed.
Operation may not be possible even if a
preset code is entered.
TV
Pioneer 0291, 0113, 0295,
0296
A.R. Systems 0155
Acme 0141
Acura 0142, 0154
ADC 0140
Admiral 0138, 0139, 0140,
0145, 0146
Adyson 0141, 0228, 0229
Agashi 0228, 0229
Agazi 0140
Aiko 0141, 0142, 0154, 0155,
0228, 0229
Aim 0155
Aiwa 0199
Akai 0142, 0143, 0149, 0152,
0154, 0155, 0228, 0229
Akiba 0143, 0155
Akura 0140, 0143, 0154, 0155
Alaron 0228
Alba 0125, 0141, 0142, 0143,
0147, 0150, 0152, 0154,
0155, 0190, 0193, 0203,
0228
Alcyon 0132
Allorgan 0229
Allstar 0149, 0155
AMOi 0224
Amplivision 0125, 0141,
0156, 0229
Amstrad 0140, 0142, 0143,
0154, 0155
Anam 0142
Anglo 0142, 0154
Anitech 0132, 0140, 0142,
0154, 0155
Ansonic 0125, 0133, 0142,
0144, 0154, 0155
Arcam 0228, 0229
Arcam Delta 0141
Aristona 0149, 0152, 0155
Arthur Martin 0156
ASA 0138, 0146
Asberg 0132, 0149, 0155
Astra 0142
Asuka 0140, 0141, 0143,
0228, 0229
Atlantic 0141, 0149, 0152,
0155, 0228
Atori 0142, 0154
Auchan 0156
Audiosonic 0125, 0141,
0142, 0143, 0149, 0152,
0155, 0229
AudioTon 0125, 0141, 0229
Ausind 0132
Autovox 0132, 0138, 0140,
0141, 0229
Awa 0228, 0229
Baird 0229
Bang & Olufsen 0138, 0230
Basic Line 0142, 0143, 0149,
0154, 0155, 0229
Bastide 0141, 0229
Baur 0152, 0155
Bazin 0229
Beko 0125, 0150, 0155, 0175
Benq 0219
Beon 0149, 0152, 0155
Best 0125
Bestar 0125, 0149, 0155
Binatone 0141, 0229
Blue Sky 0143, 0155
Blue Star 0151
Boots 0141, 0229
BPL 0151, 0155
Brandt 0148, 0153, 0157,
0159
Brinkmann 0155
Brionvega 0138, 0149, 0152,
0155
Britannia 0141, 0228, 0229
Bruns 0138
BTC 0143
Bush 0142, 0143, 0145, 0147,
0149, 0151, 0152, 0154,
0155, 0180, 0193, 0229
Capsonic 0140
Carena 0155
Carrefour 0147
Cascade 0142, 0154, 0155
Casio 0221
Cathay 0149, 0152, 0155
CCE 0229
Centurion 0149, 0152, 0155
Century 0138
CGE 0125, 0132
Cimline 0142, 0154
City 0142, 0154
Clarivox 0152
Clatronic 0125, 0132, 0140,
0141, 0142, 0143, 0149,
0150, 0154, 0155, 0229
CMS 0228
CMS Hightec 0229
Concorde 0142, 0154
Condor 0125, 0141, 0149,
0150, 0154, 0155, 0228
Contec 0141, 0142, 0147,
0154, 0228
Continental Edison 0148
Cosmel 0142, 0154
Crosley 0132, 0138
Crown 0125, 0132, 0142,
0149, 0150, 0152, 0154,
0155
CS Electronics 0141, 0143,
0228
CTC Clatronic 0144
Cybertron 0143
Daewoo 0128, 0141, 0142,
0149, 0154, 0155, 0169,
0179, 0206, 0228, 0229
Dainichi 0143, 0228
Dansai 0140, 0149, 0152,
0155, 0228, 0229
Dantax 0125, 0152
Dawa 0155
Daytron 0142, 0154
De Graaf 0145
Decca 0141, 0149, 0152,
0155, 0229
Denver 0213, 0218
Desmet 0149, 0152, 0155
Diamant 0155
Diamond 0228
Dixi 0142, 0149, 0152, 0154,
0155, 0229
DTS 0142, 0154
Dual 0141, 0155, 0229
Dual-Tec 0141, 0142
Dumont 0138, 0141, 0144,
0229
Dux 0152
Dynatron 0149, 0152, 0155
Elbe 0125, 0133, 0155, 0229
Elcit 0138
Electa 0151
ELECTRO TECH 0142
Elin 0141, 0149, 0152, 0154,
0155, 0228
Elite 0143, 0149, 0155
Elman 0144
Elta 0142, 0154, 0228
Emerson 0125, 0138, 0155
Epson 0216
Erres 0149, 0152, 0155
ESC 0229
Etron 0142
Eurofeel 0229, 0140
Euroline 0152
Euroman 0125, 0140, 0141,
0149, 0155, 0228, 0229
Europhon 0141, 0144, 0149,
0155, 0228, 0229
Expert 0156
Exquisit 0155
Fenner 0142, 0154
Ferguson 0148, 0152, 0153,
0157
Fidelity 0141, 0145, 0155,
0228
Filsai 0229
Finlandia 0145
Finlux 0132, 0138, 0141,
0144, 0149, 0152, 0155,
0229
Firstline 0141, 0142, 0149,
0154, 0155, 0228, 0229
55
En
VSX-820_PWXCN_En.book 56 ページ
09
Controlling the rest of your system
Fisher 0125, 0138, 0141,
0147, 0150, 0229
Flint 0149, 0155
Formenti 0132, 0138, 0139,
0141, 0152, 0228
Formenti/Phoenix 0228
Fortress 0138, 0139
Fraba 0125, 0155
Friac 0125
Frontech 0140, 0142, 0145,
0146, 0154, 0229
Fujitsu 0229
Fujitsu General 0229
Funai 0140
Galaxi 0155, 0150
Galaxis 0125, 0155
GBC 0142, 0147, 0154
Geant Casino 0156
GEC 0141, 0146, 0149, 0152,
0155, 0229
Geloso 0142, 0145, 0154
General Technic 0142, 0154
Genexxa 0143, 0146, 0149,
0155
Giant 0229
GoldHand 0228
Goldline 0155
Goldstar 0125, 0141, 0142,
0145, 0149, 0152, 0154,
0155, 0228, 0229
Goodmans 0140, 0142,
0147, 0149, 0152, 0154,
0155, 0222, 0229
Gorenje 0125, 0150
GPM 0143
Graetz 0146
Granada 0132, 0141, 0145,
0147, 0149, 0152, 0155,
0156, 0229
Grandin 0142, 0143, 0151,
0152
Gronic 0229
Grundig 0124, 0125, 0132,
0155, 0162
Halifax 0140, 0141, 0228,
0229
Hampton 0141, 0228, 0229
Hanseatic 0125, 0133, 0141,
0142, 0147, 0149, 0152,
0154, 0155, 0229
Hantarex 0142, 0154, 0155
Hantor 0155
Harwood 0154, 0155
HCM 0140, 0141, 0142, 0151,
0154, 0155, 0229
Hema 0154, 0229
Higashi 0228
HiLine 0155
Hinari 0142, 0143, 0147,
0149, 0152, 0154, 0155
Hisawa 0143, 0151, 0156
Hitachi 0137, 0141, 0145,
0146, 0147, 0155, 0191,
0226, 0229
Hornyphon 0149, 0155
Hoshai 0143
Huanyu 0141, 0228
56
En
2010年4月2日 金曜日 午後1時30分
Hygashi 0141, 0228, 0229
Hyper 0141, 0142, 0154,
0228, 0229
Hypson 0140, 0141, 0149,
0151, 0152, 0155, 0156,
0229
Iberia 0155
ICE 0140, 0141, 0142, 0143,
0149, 0154, 0155, 0228,
0229
ICeS 0228
Imperial 0125, 0132, 0146,
0149, 0150, 0155
Indiana 0149, 0152, 0155
Ingelen 0146
Ingersol 0142, 0154
Inno Hit 0132, 0141, 0142,
0143, 0149, 0152, 0154,
0155, 0229
Innovation 0140, 0142
Interactive 0125
Interbuy 0142, 0154
Interfunk 0125, 0138, 0146,
0149, 0152, 0155
International 0228
Intervision 0125, 0140, 0141,
0144, 0155, 0229
Irradio 0132, 0142, 0143,
0149, 0152, 0154, 0155
Isukai 0143, 0155
ITC 0141, 0229
ITS 0143, 0149, 0151, 0155,
0228
ITT 0142, 0146
ITV 0142, 0152, 0155
JVC 0134, 0135, 0147, 0149,
0192
Kaisui 0141, 0142, 0143,
0151, 0154, 0155, 0228,
0229
Kamosonic 0141
Kamp 0141, 0228
Kapsch 0146
Karcher 0125, 0141, 0142,
0152, 0155
Kawasho 0228
Kendo 0125, 0144, 0145,
0155
KIC 0229
Kingsley 0141, 0228
Kneissel 0125, 0133, 0155
Kolster 0149, 0155
Konka 0143
Korpel 0149, 0152, 0155
Korting 0125, 0138
Kosmos 0155
Koyoda 0142
KTV 0141, 0229
Kyoto 0228, 0229
Lasat 0125
Lenco 0142, 0154
Lenoir 0141, 0142, 0154
Leyco 0140, 0149, 0152, 0155
LG 0125, 0136, 0141, 0142,
0145, 0149, 0152, 0154,
0155, 0186, 0189, 0196,
0220, 0228, 0229
LG/GoldStar 0129
Liesenk 0152
Liesenkotter 0155
Life 0140, 0142
Lifetec 0140, 0142, 0154,
0155
Lloyds 0154
Loewe 0125, 0133, 0155,
0166, 0167
Loewe Opta 0138, 0149,
0152
Luma 0145, 0152, 0154, 0155
Lumatron 0145, 0149, 0152,
0155, 0229
Lux May 0149
Luxor 0141, 0145, 0229
M Electronic 0141, 0142,
0146, 0148, 0149, 0152
Magnadyne 0138, 0144,
0152
Magnafon 0132, 0141, 0144,
0228
Magnum 0140, 0142
Mandor 0140
Manesth 0140, 0141, 0149,
0152, 0155, 0229
Marantz 0149, 0152, 0155
Marelli 0138
Mark 0149, 0152, 0154, 0155,
0228, 0229
Masuda 0229
Matsui 0141, 0142, 0145,
0147, 0149, 0152, 0154,
0155, 0229
Mediator 0149, 0152, 0155
Medion 0140, 0142, 0155
M-Electronic 0154, 0155,
0228, 0229
Melvox 0156
Memorex 0142, 0154
Memphis 0142, 0154
Mercury 0154, 0155
Metz 0138, 0299, 0300, 0301,
0302
Micromaxx 0140, 0142
Microstar 0140, 0142
Minerva 0132
Minoka 0149, 0155
Mitsubishi 0138, 0147, 0149,
0155, 0200
Mivar 0125, 0132, 0133, 0141,
0228, 0229
Motion 0132
MTC 0125, 0228
Multi System 0152
Multitech 0125, 0141, 0142,
0144, 0145, 0147, 0152,
0154, 0155, 0228, 0229
Murphy 0141, 0228
Naonis 0145
NEC 0147, 0229
Neckermann 0125, 0138,
0141, 0145, 0149, 0150,
0152, 0155, 0229
NEI 0149, 0152, 0155
Neufunk 0154, 0155
New Tech 0142, 0149, 0154,
0155, 0229
New World 0143
Nicamagic 0141, 0228
Nikkai 0140, 0141, 0143,
0149, 0152, 0154, 0155,
0228, 0229
Nobliko 0132, 0141, 0144,
0228
Nokia 0146
Nordic 0229
Nordmende 0138, 0146,
0148, 0149
Nordvision 0152
Novatronic 0155
Oceanic 0146, 0156
Okano 0125, 0150, 0155
ONCEAS 0141
Opera 0155
Orbit 0149, 0155
Orion 0142, 0149, 0152, 0154,
0155, 0194
Orline 0155
Osaki 0140, 0141, 0143, 0155,
0229
Oso 0143
Otto Versand 0139, 0141,
0147, 0149, 0151, 0152,
0155, 0229
Pael 0141, 0228
Palladium 0125, 0141, 0150,
0155, 0229
Palsonic 0229
Panama 0140, 0141, 0142,
0154, 0155, 0228, 0229
Panasonic 0123, 0146, 0155,
0158, 0164, 0214, 0217
Panavision 0155
Pathe Cinema 0125, 0133,
0141, 0156, 0228
Pausa 0142, 0154
Perdio 0155, 0228
Perfekt 0155
Philco 0125, 0132, 0138, 0155
Philharmonic 0141, 0229
Philips 0115, 0117, 0138,
0141, 0149, 0152, 0155,
0160, 0163, 0165, 0170,
0171, 0173, 0174, 0182,
0183, 0195, 0196, 0202,
0205, 0212, 0215
Phoenix 0125, 0138, 0149,
0152, 0155, 0228
Phonola 0138, 0149, 0152,
0155, 0228
Plantron 0140, 0149, 0154,
0155
Playsonic 0229
Poppy 0142, 0154
Prandoni-Prince 0132, 0145
Precision 0141, 0229
Prima 0142, 0146, 0154
VSX-820_PWXCN_En.book 57 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Profex 0142, 0154
Profi-Tronic 0149, 0155
Proline 0149, 0155
Prosonic 0125, 0141, 0152,
0155, 0228, 0229, 0232
Protech 0140, 0141, 0142,
0144, 0149, 0152, 0229
Provision 0152, 0155
Pye 0149, 0152, 0155, 0198
Pymi 0142, 0154
Quandra Vision 0156
Quelle 0140, 0141, 0149,
0152, 0155, 0229
Questa 0147
Radialva 0155
Radio Shack 0155
Radiola 0149, 0152, 0155,
0229
Radiomarelli 0138, 0155
Radiotone 0125, 0149, 0154,
0155
Rank 0147
Recor 0155
Redstar 0155
Reflex 0155
Revox 0125, 0149, 0152, 0155
Rex 0140, 0145, 0146
RFT 0125, 0133, 0138
Rhapsody 0228
R-Line 0149, 0152, 0155
Roadstar 0140, 0142, 0143,
0154
Robotron 0138
Rowa 0228, 0229
Royal Lux 0125
RTF 0138
Saba 0138, 0146, 0148, 0153,
0157, 0159
Saisho 0140, 0141, 0142,
0154, 0229
Salora 0145, 0146
Sambers 0132, 0144
Samsung 0119, 0120, 0125,
0140, 0141, 0142, 0149,
0150, 0152, 0154, 0155,
0177, 0178, 0181, 0204,
0208, 0228, 0229
Sandra 0141, 0228, 0229
Sansui 0149, 0155
Sanyo 0125, 0133, 0141,
0147, 0154, 0187, 0228,
0229
SBR 0152, 0155
SCHAUB LORENTZ 0146
Schneider 0141, 0143, 0149,
0152, 0155, 0190, 0229
SEG 0140, 0141, 0144, 0147,
0152, 0154, 0155, 0190,
0228, 0229
SEI 0155
SEI-Sinudyne 0138, 0144,
0146
Seleco 0145, 0146, 0147
Sencora 0142, 0154
Sentra 0154
Serino 0228
Sharp 0130, 0131, 0139, 0147,
0184, 0207
Siarem 0138, 0144, 0155
Sierra 0149, 0155
Siesta 0125
Silva 0228
Silver 0147
Singer 0138, 0144, 0156
Sinudyne 0138, 0144, 0152,
0155
Skantic 0146
Solavox 0146
Sonitron 0125, 0229
Sonoko 0140, 0141, 0142,
0149, 0152, 0154, 0155,
0229
Sonolor 0146, 0156
Sontec 0125, 0149, 0152,
0155
Sony 0116, 0118, 0142, 0147,
0161, 0168, 0172, 0185,
0188, 0197, 0201, 0211,
0225, 0227
Sound & Vision 0143, 0144
Soundwave 0149, 0152,
0155
Standard 0141, 0142, 0143,
0149, 0154, 0155, 0229
Starlight 0152
Starlite 0154, 0155
Stenway 0151
Stern 0145, 0146
Strato 0154, 0155
Stylandia 0229
Sunkai 0142
Sunstar 0154, 0155
Sunwood 0142, 0149, 0154,
0155
Superla 0141, 0228, 0229
SuperTech 0154, 0155, 0228
Supra 0142, 0154
Susumu 0143
Sutron 0142, 0154
Sydney 0141, 0228, 0229
Sysline 0152
Sytong 0228
Tandy 0139, 0141, 0143,
0146, 0229
Tashiko 0144, 0145, 0147,
0228, 0229
Tatung 0141, 0149, 0152,
0155, 0229
TCM 0140, 0142
Teac 0155, 0229
Tec 0141, 0142, 0154, 0229
TEDELEX 0229
Teleavia 0148
Telecor 0155, 0229
Telefunken 0148, 0149,
0155, 0157
Telegazi 0155
Telemeister 0155
Telesonic 0155
Telestar 0155
Teletech 0142, 0152, 0154,
0155
Teleton 0141, 0229
Televideon 0228
Televiso 0156
Tensai 0142, 0143, 0149,
0154, 0155, 0229
Tesmet 0149
Tevion 0140, 0142
Texet 0141, 0154, 0228, 0229
Thomson 0121, 0122, 0141,
0148, 0149, 0153, 0155,
0157, 0159, 0210
09
Thorn 0152, 0155
Tokai 0149, 0155, 0229
Tokyo 0141, 0228
Tomashi 0151
Toshiba 0126, 0127, 0147,
0176, 0209, 0229
Towada 0146, 0229
Trakton 0229
Trans Continens 0155, 0229
Transtec 0228
Trident 0229
Triumph 0155
Vestel 0145, 0146, 0149,
0150, 0152, 0155, 0229
Vexa 0142, 0152, 0154, 0155
Victor 0147, 0149
VIDEOLOGIC 0228
Videologique 0141, 0143,
0228, 0229
VideoSystem 0149, 0155
Videotechnic 0228, 0229
Viewsonic 0223
Visiola 0141, 0228
Vision 0149, 0155, 0229
Vortec 0149, 0152, 0155
Voxson 0132, 0138, 0145,
0146, 0149, 0155
Waltham 0141, 0155, 0229
Watson 0149, 0152, 0155
Watt Radio 0141, 0144, 0228
Wega 0138, 0147, 0155
Wegavox 0154
Weltblick 0149, 0152, 0155,
0229
White Westinghouse
0141, 0144, 0152, 0155,
0228
Xrypton 0155
Yamishi 0155, 0229
Yokan 0155
Yoko 0125, 0140, 0141, 0142,
0143, 0149, 0152, 0154,
0155, 0228, 0229
Yorx 0143
Zanussi 0145, 0229
DVD
If operations are not possible using the preset codes below, you may be able to conduct operations
with the preset codes for the BD, DVR (BDR, HDR).
Pioneer 2256, 2014
AEG 2188
Aiwa 2149
Akai 2096
Akura 2186
Alba 2122, 2133, 2143
Amitech 2188
AMW 2189
Awa 2189
Bang & Olufsen 2191
Bellagio 2189
Best Buy 2185
Brainwave 2188
Brandt 2112, 2139
Bush 2122, 2143, 2177, 2184
Cambridge Audio 2180
CAT 2182, 2183
Centrum 2183
CGV 2180, 2188
Cinetec 2189
Clatronic 2184
Coby 2190
Conia 2177
Continental Edison 2189
Crown 2188
C-Tech 2181
CyberHome 2103, 2132
Daenyx 2189
Daewoo 2130, 2154, 2188,
2189
Daewoo International
2189
Dalton 2187
Dansai 2179, 2188
Daytek 2105, 2128, 2189
Dayton 2189
DEC 2184
Decca 2188
Denon 2161, 2163
Denver 2164, 2184, 2186,
2190
Denzel 2178
Diamond 2180, 2181
DK Digital 2129
Dmtech 2095
Dual 2178
DVX 2181
Easy Home 2185
57
En
VSX-820_PWXCN_En.book 58 ページ
09
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Eclipse 2180
Electrohome 2188
Elin 2188
Elta 2142, 2188
Enzer 2178
Finlux 2180, 2188
Gericom 2145
Global Solutions 2181
Global Sphere 2181
Goodmans 2122, 2165, 2184
Graetz 2178
Grundig 2148
Grunkel 2188
H&B 2184
Haaz 2180, 2181
HiMAX 2185
Hitachi 2110, 2178, 2185
Innovation 2097
JVC 2119, 2136, 2152
Kansai 2190
Kennex 2188
Kenwood 2146
KeyPlug 2188
Kiiro 2188
Kingavon 2184
Kiss 2178
Koda 2184
KXD 2185
Lawson 2181
Lecson 2179
Lenco 2184, 2188
LG 2111, 2115, 2135, 2138,
2160, 2171
Life 2097
Lifetec 2097
Limit 2181
Loewe 2151
LogicLab 2181
Magnavox 2184
Majestic 2190
Marantz 2157
Marquant 2188
Matsui 2139
Mecotek 2188
Medion 2097
MiCO 2180
Micromaxx 2097
Microstar 2097
Minoka 2188
Mizuda 2184, 2185
Monyka 2178
Mustek 2101
Mx Onda 2180
Naiko 2188
Neufunk 2178
Nevir 2188
NU-TEC 2177
Onkyo 2167
Optim 2179
Optimus 2099
Orava 2184
Orbit 2189
Orion 2156
P&B 2184
Pacific 2181
Panasonic 2113, 2114, 2121,
2127, 2131, 2170
Philips 2100, 2106, 2117,
2118, 2126, 2134, 2157
Pointer 2188
Portland 2188
Powerpoint 2189
Prosonic 2190
Provision 2184
Raite 2178
RedStar 2186, 2188, 2190
Reoc 2181
Roadstar 2116, 2184
Ronin 2189
Rowa 2177
Rownsonic 2183
Saba 2112, 2139
Sabaki 2181
Saivod 2188
Samsung 2110, 2137, 2158,
2173, 2176
Sansui 2180, 2181, 2188
Sanyo 2140, 2166
ScanMagic 2101
Schaub Lorenz 2188
Schneider 2095
Scientific Labs 2181
Scott 2120, 2187
SEG 2116, 2178, 2181, 2189
Sharp 2097, 2141, 2174
Sigmatek 2185
Silva 2186
Singer 2180, 2181
Skymaster 2153, 2181
Skyworth 2186
Slim Art 2188
SM Electronic 2181
Sony 2104, 2108, 2123, 2124,
2125, 2150, 2175
Soundmaster 2181
Soundmax 2181
Spectra 2189
Standard 2181
Star Cluster 2181
Starmedia 2184
Sunkai 2188
Supervision 2181
Synn 2181
Tatung 2130, 2188
TCM 2097
Teac 2162, 2177, 2181
Tec 2186
Technika 2188
Telefunken 2183
Tensai 2188
Tevion 2097, 2181, 2187
Thomson 2098, 2112, 2155,
2159
Tokai 2178, 2186
Toshiba 2102, 2156, 2168,
2169, 2172
TRANScontinents 2189
Trio 2188
TruVision 2185
Wharfedale 2180, 2181
Xbox 2098
Xlogic 2181, 2188
XMS 2188
Yamada 2189
Yamaha 2106
Yamakawa 2178, 2189
Yukai 2101, 2147
BD
If operations are not possible using the preset codes below, you may be able to conduct operations
with the preset codes for the DVD, DVR (BDR, HDR).
Pioneer 2255, 2192, 2281
Denon 2310, 2311, 2312
Hitachi 2307, 2308, 2309
JVC 2290, 2291, 2293, 2294,
2295, 2296
LG 2286, 2287
Marantz 2302, 2303
Mitsubishi 2300, 2301
Onkyo 2289
Panasonic 2277, 2278, 2279
Philips 2280
Samsung 2282
Sharp 2304, 2305, 2306
Sony 2283, 2284, 2285, 2292
Toshiba 2288, 2262
Yamaha 2297, 2298, 2299
DVR (BDR, HDR)
If operations are not possible using the preset codes below, you may be able to conduct operations
with the preset codes for the DVD, BD.
Pioneer 2257, 2193, 2258,
2259, 2260, 2261, 2264,
2265, 2266, 2270
Panasonic 2263, 2269
Sharp 2267, 2275
Sony 2268, 2271, 2272, 2273,
2276
Toshiba 2274
58
En
VSX-820_PWXCN_En.book 59 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
09
VCR
Pioneer 1053, 1108
Adyson 1050
Aiwa 1033, 1034, 1035
Akai 1034
Akiba 1040, 1050
Akura 1034, 1040, 1050
Alba 1035, 1036, 1037, 1040,
1050, 1051
Ambassador 1037
Amstrad 1033, 1050, 1051
Anitech 1040, 1050
ASA 1038, 1039
Asuka 1033, 1038, 1039,
1040, 1050
Audiosonic 1051
Baird 1033, 1034, 1036, 1051
Bang & Olufsen 1052
Basic Line 1035, 1036, 1037,
1040, 1050, 1051
Baur 1039
Bestar 1036, 1037, 1051
Black Panther Line 1036,
1051
Blaupunkt 1039
Bondstec 1037, 1050
Bush 1035, 1036, 1040, 1050,
1051
Cathay 1051
Catron 1037
CGE 1033, 1034
Cimline 1035, 1040, 1050
Clatronic 1037, 1050
Condor 1036, 1037, 1051
Crown 1036, 1037, 1040,
1050, 1051
Daewoo 1036, 1037, 1051
Dansai 1040, 1050, 1051
Dantax 1035
Daytron 1036, 1051
De Graaf 1039
Decca 1033, 1034, 1039
Denko 1050
Dual 1034, 1051, 1060
Dumont 1033, 1039
Elbe 1051
Elcatech 1050
Elsay 1050
Elta 1040, 1050, 1051
Emerson 1050
ESC 1036, 1051
Etzuko 1040, 1050
Ferguson 1034
Fidelity 1033, 1050
Finlandia 1039
Finlux 1033, 1034, 1039
Firstline 1035, 1038, 1040,
1050
Flint 1035
Formenti/Phoenix 1039
Frontech 1037
Fujitsu 1033
Funai 1033
Galaxy 1033
GBC 1037, 1040
GEC 1039
Geloso 1040
General 1037
General Technic 1035
GoldHand 1040, 1050
Goldstar 1033, 1048
Goodmans 1033, 1036,
1037, 1038, 1040, 1050,
1051
Graetz 1034
Granada 1039
Grandin 1033, 1036, 1037,
1038, 1040, 1050, 1051
Grundig 1039, 1040
Hanseatic 1038, 1039, 1051
Harwood 1050
HCM 1040, 1050
Hinari 1035, 1040, 1050, 1051
Hisawa 1035
Hitachi 1033, 1034, 1039,
1045
Hypson 1035, 1040, 1050,
1051
Impego 1037
Imperial 1033
Inno Hit 1036, 1037, 1039,
1040, 1050, 1051
Innovation 1035
Interbuy 1038, 1050
Interfunk 1039
Intervision 1033, 1051
Irradio 1038, 1040, 1050
ITT 1034
ITV 1036, 1038, 1051
JVC 1034, 1046
Kaisui 1040, 1050
Karcher 1039
Kendo 1035, 1036, 1037,
1050
Korpel 1040, 1050
Kyoto 1050
Lenco 1036
Leyco 1040, 1050
LG 1033, 1038, 1049
Lifetec 1035
Loewe Opta 1038, 1039
Logik 1040, 1050
Lumatron 1036, 1051
Luxor 1050
M Electronic 1033
Manesth 1040, 1050
Marantz 1039
Mark 1051
Matsui 1035, 1038
Matsushita 1033, 1039
Mediator 1039
Medion 1035
Memorex 1033, 1038
Memphis 1040, 1050
Micromaxx 1035
Microstar 1035
Migros 1033
Multitech 1033, 1037, 1039,
1040, 1050
Murphy 1033
NEC 1034
Neckermann 1034, 1039
NEI 1039
Nesco 1040, 1050
Nikkai 1037, 1050, 1051
Nokia 1034, 1051
Nordmende 1034
Oceanic 1033, 1034
Okano 1035, 1050, 1051
Orion 1035
Orson 1033
Osaki 1033, 1038, 1040, 1050
Otto Versand 1039
Palladium 1034, 1038, 1040,
1050
Panasonic 1043
Pathe Marconi 1034
Perdio 1033
Philco 1050
Philips 1039, 1045, 1052
Phonola 1039
Portland 1036, 1037, 1051
Prinz 1033
Profex 1040
Proline 1033
Prosonic 1035, 1051
Pye 1039
Quelle 1033, 1039
Radialva 1050
Radiola 1039
Rex 1034
RFT 1037, 1039, 1050
Roadstar 1036, 1038, 1040,
1050, 1051
Royal 1050
Saba 1034
Saisho 1035, 1040
Samsung 1041
Samurai 1037, 1050
Sansui 1034
Saville 1051
SBR 1039
Schaub Lorenz 1033, 1034
Schneider 1033, 1035, 1036,
1037, 1038, 1039, 1040,
1050, 1051
SEG 1040, 1050, 1051
SEI-Sinudyne 1039
Seleco 1034
Sentra 1037, 1050
Sentron 1040, 1050
Sharp 1042
Shintom 1040, 1050
Shivaki 1038
Siemens 1038
Silva 1038
Silver 1051
Sinudyne 1039
Solavox 1037
Sonneclair 1050
Sonoko 1036, 1051
Sontec 1038
Sony 1044
Standard 1036, 1051
Stern 1051
Sunkai 1035
Sunstar 1033
Suntronic 1033
Sunwood 1040, 1050
Symphonic 1050
Taisho 1035
Tandberg 1051
Tashiko 1033
Tatung 1033, 1034, 1039
TCM 1035
Teac 1051
Tec 1037, 1050, 1051
Teleavia 1034
Telefunken 1034
Teletech 1050, 1051
Tenosal 1040, 1050
Tensai 1033, 1038, 1040,
1050
Tevion 1035
Thomson 1034, 1048
Thorn 1034
Tokai 1038, 1040, 1050
Tonsai 1040
Toshiba 1034, 1039, 1047
Towada 1040, 1050
Towika 1040, 1050
TVA 1037
Uher 1038
Ultravox 1051
United Quick Star 1036,
1051
Universum 1033, 1038, 1039
Videon 1035
Weltblick 1038
Yamishi 1040, 1050
Yokan 1040, 1050
Yoko 1037, 1038, 1040, 1050
59
En
VSX-820_PWXCN_En.book 60 ページ
09
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Satellite Set Top Box
Pioneer 6220, 6219, 6204
@sat 6251
@Sky 6238
ABsat 6180
Acoustic Solutions 6217
ADB 6174
Akai 6214
Akura 6228
Alba 6176, 6200, 6180, 6217
Allsat 6214
Alltech 6180
Allvision 6252, 6238, 6199
Amitronica 6180
Ampere 6256, 6261
Amstrad 6202, 6243, 6256,
6261, 6236, 6180
Anglo 6180
Ankaro 6180
Ansonic 6245
Anttron 6200
Apollo 6176
Apro 6232
Arcon 6192
Arcus 6193
Armstrong 6214
Arnion 6251
ASA 6230
Asat 6214
ASCI 6213, 6238
ASLF 6180
AssCom 6220
Astra 6255, 6180
Astratec 6268, 6269
Astrell 6202
Astro 6177, 6236, 6255, 6200,
6246, 6215, 6222, 6243
Atlanta 6245
Atsat 6251
AtSky 6238
Audioline 6232
Audioton 6200
Austar 6174
Avalon 6261
Axil 6244, 6186, 6245
Axis 6267
Axitronic 6228
B.net 6232
B@ytronic 6230, 6199
Balmet 6186
Beko 6176
Belson 6245
Big Sat 6186
Black Diamond 6217
Blaupunkt 6177
Blue Sky 6180
Boca 6256, 6180, 6252, 6185,
6257, 6237, 6187, 6188
Bodner & Mann 6194
Boshmann 6244, 6247
Boston 6227
Brainwave 6232, 6231
British Sky Broadcasting
6210
Broco 6180
60
En
BskyB 6210
BT 6195
Bubu Sat 6180
Bush 6254, 6217, 6264, 6228,
6190, 6232, 6268, 6201,
6265, 6182
Cambridge 6236
Canal Digital 6220
Canal Satellite 6220, 6219,
6278, 6277
Canal+ 6220, 6277
CGV 6244, 6183
Cherokee 6194
Chess 6213, 6180, 6238, 6228
CityCom 6229, 6255, 6179,
6192, 6241, 6252
Clark 6200
Classic 6232
Clatronic 6244
Clayton 6228
Clemens Kamphus 6261
Cobra 6261
Colombia 6256
Columbia 6256
Comag 6256, 6252, 6185,
6199, 6244, 6257, 6237,
6189, 6187, 6188
Comsat 6244
Condor 6255, 6253
Connexions 6261
Conrad 6256, 6236, 6207,
6255
Coship 6186, 6232
Crown 6217
Cryptovision 6176
CS 6247
Cyfrowy Polsat 6220
Cyrus 6214
D-box 6275
Daewoo 6267, 6180, 6195,
6268, 6182
Dantax 6228
Deltasat 6192
Denver 6245
Digatron 6231
Digenius 6229, 6226
Digiality 6255, 6238
Digifusion 6268, 6269
Digihome 6217, 6265, 6218
DigiLogic 6217
DigiQuest 6251, 6186, 6247
DigiSat 6252
Digisky 6186
Digital 6187
Digital Vision 6269
DigitalBox 6222, 6247
Dijam 6195
DirecTV 6263
Discovery 6194
Distratel 6202, 6250
DMT 6192
DNT 6214, 6261
Doro 6232
Dual 6252
Durabrand 6217, 6218
Echolink 6185
Echostar 6220, 6233, 6261,
6176, 6180, 6181, 6239
Edision 6247
Einhell 6256, 6236, 6180
Elap 6180, 6244, 6183
Elbe 6245
Elless 6230
Elsat 6180
Elta 6214
eMTech 6196
Energy Sistem 6247
Engel 6180, 6227
EP Sat 6176
Eurieult 6202
Eurocrypt 6176
EuroLine 6227
Europa 6236, 6255
Europhon 6256, 6229, 6255
Eurosat 6189
Eurosky 6256, 6213, 6229,
6236, 6255, 6230
Eurostar 6255, 6179
Eutelsat 6180
Eutra 6230
Evesham 6218
Exator 6200
Fagor 6203
Fenner 6180
Ferguson 6176, 6264, 6268,
6269
Fidelity 6236
Finlandia 6176
Finlux 6176, 6207, 6228
FinnSat 6230
Flair Mate 6180
Fly Com 6186
FMD 6213, 6244, 6186
Freecom 6236
FTEmaximal 6180, 6189
Fuba 6177, 6229, 6261, 6207,
6226, 6196
Galaxis 6220, 6267
Gardiner 6179
Garnet 6192
GbSAT 6196
Gecco 6246, 6199
General Satellite 6241
Globo 6230, 6227, 6238,
6199, 6257
GOD Digital 6214
Gold Box 6220, 6219
Gold Vision 6247
Golden Interstar 6250
Goodmans 6176, 6254,
6217, 6264, 6271, 6218,
6201, 6190
Gran Prix 6230
Granada 6176
Grandin 6228
Grocos 6239, 6186
Grundig 6220, 6177, 6217,
6264, 6232, 6218, 6201,
6190
Haensel & Gretel 6256
Haier 6245
Hama 6183
Hanseatic 6215, 6222
Hauppauge 6231, 6232
HB 6196
Heliocom 6255
Helium 6255
Hiro 6189
Hirschmann 6267, 6177,
6229, 6261, 6236, 6207,
6255, 6230, 6252, 6199,
6189
Hitachi 6176, 6217, 6218
HNE 6256
Hornet 6251
Houston 6261
Humax 6241, 6268, 6242
Huth 6256, 6255, 6192, 6193
Hyundai 6192
ID Digital 6241
ILLUSION sat 6247
Imperial 6222, 6216, 6223,
6238, 6232
Ingelen 6213, 6261
Inno Hit 6228
International 6256
Interstar 6196
Intervision 6255
Inves 6268
iotronic 6244
ITT Nokia 6176, 6207
Jaeger 6238
K-SAT 6180
Kamm 6180
Kaon 6251
KaTelco 6267
Kathrein 6177, 6214, 6213,
6262, 6200, 6180, 6179,
6272, 6183
Kendo 6252
Kenwood 6220
Key West 6256
Kiton 6213
KR 6200
Kreiling 6213, 6194, 6228
Kreiselmeyer 6177
Kyostar 6200
L&S Electronic 6256, 6238
Labgear 6195
LaSAT 6177, 6256, 6229,
6255, 6230
Leiko 6228
Lemon 6238
Lenco 6255, 6180
Lenson 6236
LG 6192
Lifesat 6256, 6229, 6180
Listo 6228
Lodos 6217
VSX-820_PWXCN_En.book 61 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Logik 6217
Logix 6192
Lorenzen 6256, 6229, 6255,
6226, 6231, 6257, 6237
Luxor 6236, 6207, 6265
M Electronic 6179
Manata 6256, 6180
Manhattan 6176, 6251
Marantz 6214
Maspro 6177, 6180
Matsui 6177, 6217, 6271,
6228, 6268, 6269
Max 6255
Maximum 6192, 6238
Mediabox 6220, 6219
Mediacom 6198
MediaSat 6220, 6219, 6236,
6278, 6277
Medion 6256, 6229, 6180,
6230, 6192, 6252, 6238,
6199, 6228
Medison 6180
Mega 6214
MegaSat 6189
Metronic 6256, 6200, 6180,
6179, 6202, 6250, 6238,
6244
Metz 6177
Micro 6236, 6255, 6200, 6180,
6231
Micro Elektronic 6180
Micro Technology 6180
Micromaxx 6229
Microstar 6229, 6192, 6226
Microtec 6180
Mitsubishi 6176
Morgan’s 6214, 6256, 6180,
6252, 6199
Multibroadcast 6174
Multichoice 6174
Myryad 6214
Mysat 6180
MySky 6212, 6211
NEOTION 6238
Netsat 6263
Neuhaus 6236, 6255, 6180
Neuling 6256, 6252, 6257,
6188
Neusat 6180
Neveling 6226
Newton 6261
NextWave 6193
Nichimen 6254
Nikko 6214, 6180
Noda Electronic 6202
Nokia 6220, 6176, 6207, 6206
Nordmende 6176
Octagon 6200
OctalTV 6231
Onn 6217, 6218
Opentel 6252, 6199
Optex 6213, 6180, 6250,
6244, 6203, 6228
Orbis 6252, 6238, 6199
Orbitech 6213, 6236, 6215,
6222, 6216, 6223
P/Sat 6252
Pace 6220, 6214, 6176, 6181,
6273, 6212, 6211
Pacific 6217
Packard Bell 6267
Palcom 6229, 6226, 6239
Palladium 6261, 6236
Palsat 6236
Panasonic 6176, 6178
Panda 6177, 6176, 6255
Pansat 6191
Pass 6183
Patriot 6256
peeKTon 6186, 6245
Philips 6220, 6177, 6214,
6275, 6219, 6277, 6268,
6232, 6179, 6200, 6176,
6263
Phoenix 6245
Phonotrend 6233
Pilotime 6278
Pino 6238
Pixx 6191
Planet 6261
PMB 6180, 6203
Polytron 6261
Portland 6195
Preisner 6256, 6261, 6243,
6185
Premier 6219
Primacom 6267
Pro Basic 6220, 6184
Proline 6217
Promax 6176
Proscan 6234
Quelle 6229, 6255
Radiola 6214
Radix 6261, 6243
Rainbow 6200
RCA 6234
Rebox 6196
Regal 6227
RFT 6214
Roadstar 6220, 6180
Rollmaster 6244
Rover 6180
Rownsonic 6183
SAB 6227, 6251
Saba 6255, 6230, 6202, 6184
Sabre 6176
Sagem 6275, 6258, 6277
Saivod 6245
Salora 6252
Samsung 6220, 6198, 6197,
6273, 6253
Sanyo 6228
SAT 6236
Sat Control 6251
Sat Partner 6236, 6200
Sat Team 6180
SAT+ 6239
Satcom 6255
Satec 6180
Satelco 6252
Satplus 6222
SatyCon 6247
Schaecke 6200
Schaub Lorenz 6196, 6245
Schneider 6198, 6227
Schwaiger 6267, 6256, 6262,
6255, 6230, 6202, 6192,
6238, 6199, 6186, 6257,
6247, 6232, 6187, 6188
Scientific Atlanta 6209
SCS 6229, 6230
Sedea Electronique 6256,
6213, 6198, 6250, 6228
Seemann 6261
SEG 6213, 6192, 6227, 6217,
6228
Septimo 6202
Serd 6199
Servimat 6203
ServiSat 6180, 6227
Shark 6247
Sharp 6265, 6218
Siemens 6177, 6261, 6238
Sigmatek 6245
Silva 6229
SilverCrest 6187
Skantin 6180
SKR 6180
SKT 6256
SKY 6263, 6210, 6212, 6211
SKY Italia 6220, 6212
Sky XL 6227, 6199
Skymaster 6233, 6180, 6192,
6238, 6239, 6183, 6203,
6184
Skymax 6214, 6244
Skypex 6230
Skyplus 6230, 6252, 6238,
6199
SkySat 6213, 6236, 6255,
6180
Skyvision 6238
SL 6256, 6229, 6230, 6231,
6257, 6232
SM Electronic 6233, 6180,
6239
Smart 6256, 6261, 6180,
6243, 6252, 6246, 6244,
6257, 6247
SmartVision 6186
Sony 6235, 6220, 6219, 6176
SR 6256
Star Sat 6196
Starland 6180
Starlite 6214
Stream 6212
Stream System 6251
Strong 6220, 6228, 6256,
6200, 6180, 6245, 6217,
6239
Sumin 6199
Sunny 6251
Sunsat 6180
Sunstar 6174, 6256
SuperMax 6193
Supratech 6244
Systec 6238
Tantec 6176
Targa 6191
09
Tatung 6176
TBoston 6227, 6245
Tecatel 6233
Technical 6228
Technika 6217, 6232, 6218
TechniSat 6213, 6261, 6176,
6236, 6215, 6222, 6216,
6223
Technomate 6250
Technosat 6193
Technosonic 6254, 6232
Technotrend 6232
Technowelt 6256, 6255
Techwood 6213, 6217, 6228,
6218
Telasat 6255
TELE System 6261, 6227,
6239, 6203
Teleciel 6200
Teleka 6261, 6236, 6255,
6200
Telesat 6255
Telestar 6213, 6236, 6215,
6222, 6216, 6223, 6227,
6238, 6228, 6232
Teletech 6213
Televes 6256, 6176, 6236,
6196, 6251, 6238, 6257
Telewire 6252
Tempo 6193
Tevion 6254, 6180, 6239,
6232, 6184
Thomson 6220, 6219, 6180,
6255, 6176, 6265, 6277,
6234, 6264, 6210, 6212
Thorn 6176
Tiny 6232
Tioko 6256
Titan 6189, 6184
TNT SAT 6258
Tokai 6214
Tonna 6176, 6236, 6180, 6203
Topfield 6198
Toshiba 6176, 6217
Trevi 6227
Triasat 6236
Triax 6220, 6214, 6256, 6189,
6253, 6228, 6203, 6261,
6213, 6257, 6244, 6195,
6264, 6227, 6243, 6180,
6236
Turnsat 6180
Twinner 6180, 6203
Unisat 6214, 6256
United 6227
Univers 6189
Universum 6177, 6213,
6229, 6255, 6230, 6215,
6227
Van Hunen 6226
Variosat 6177
VEA 6245
Ventana 6214
Vestel 6213, 6227, 6217, 6218
VH Sat 6229
Viasat 6273
Viola Digital 6232
61
En
VSX-820_PWXCN_En.book 62 ページ
09
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
Vision 6228, 6189
Visionic 6250
Visiosat 6213, 6254, 6180,
6244, 6186, 6191
Vitecom 6244
Volcasat 6245
VTech 6179
Wetekom 6236
Wewa 6176
Wharfedale 6217, 6265,
6218
Wisi 6177, 6256, 6229, 6261,
6176, 6236, 6255, 6230,
6252, 6199
Worldsat 6213, 6196, 6227,
6194
WorthIt! 6190
Woxter 6245
Xoro 6191
Xsat 6180, 6196, 6181
Xtreme 6251
Yakumo 6244
ZapMaster 6230
Zehnder 6213, 6262, 6179,
6192, 6252, 6227, 6238,
6199, 6244, 6247, 6249
Zeta Technology 6214
Zodiac 6261, 6200
Satellite Set Top Box (SAT/PVR Combination)
@sat 6251
Allvision 6199
Atsat 6251
B@ytronic 6230, 6199
Boca 6187
BskyB 6210
Bush 6254
Canal Satellite 6278
Comag 6199, 6187
Daewoo 6182
Digifusion 6269
Digihome 6218
DigiQuest 6251
Digital 6187
DMT 6192
Edision 6247
eMTech 6196
GbSAT 6196
Gecco 6199
Globo 6199
Goodmans 6254, 6218
Hirschmann 6230, 6199
Humax 6241, 6242
Huth 6192
Hyundai 6192
Kathrein 6272
LaSAT 6230
LG 6192
Luxor 6265
Maximum 6238
Mediacom 6198
MediaSat 6277
Medion 6230, 6199
Microstar 6192
Morgan’s 6199
MySky 6212, 6211
NEOTION 6238
Nichimen 6254
Nokia 6206
Opentel 6199
Orbis 6199
Pace 6273, 6211
Panasonic 6178
Philips 6263, 6277
Pilotime 6278
Pixx 6191
Proscan 6234
Rebox 6196
Sagem 6258
Samsung 6198, 6197, 6273
Sat Control 6251
Schneider 6198
Schwaiger 6230, 6192, 6199,
6187
Sedea Electronique 6198
Serd 6199
Sharp 6218
SilverCrest 6187
SKY 6210, 6212, 6211
SKY Italia 6212
Sky XL 6199
Skymaster 6192
Skypex 6230
Skyplus 6230, 6238, 6199
Stream System 6251
Sumin 6199
Sunny 6251
Targa 6191
TechniSat 6216, 6223
Technosonic 6254
Telestar 6216, 6223
Thomson 6210, 6265
TNT SAT 6258
Topfield 6198
Viasat 6273
Visiosat 6254, 6191
Wisi 6230
Xoro 6191
Xtreme 6251
Zehnder 6192, 6199, 6249
General Instrument 6276
6266
Humax 6224, 6248
Jerrold 6276, 6266
Kabel Deutschland 6224
Macab 6260
Madritel 6175
Magnavox 6266
Memorex 6240
Motorola 6276
Nokia 6208
Noos 6260
NTL 6276, 6221
Optus 6276
Orange 6260
Pace 6221
Panasonic 6240
Paragon 6240
Philips 6260, 6270
Pulsar 6240
Runco 6240
Sagem 6260
Salora 6240
Samsung 6221, 6240
Scientific Atlanta 6225
StarHub 6276
Supercable 6276
Telewest 6225
Thomson 6270, 6224
Toshiba 6240
UPC 6270
US Electronics 6276
Virgin Media 6225, 6221
Visiopass 6260
Zenith 6240
Ziggo 6208
Cable Set Top Box
Pioneer 6205
ABC 6266
ADB 6175
Auna 6175
Austar 6276
Bell & Howell 6266
Birmingham Cable
Communications 6276
Cablecom 6270
Fosgate 6276
France Telecom 6260
Freebox 6274
Cable Set Top Box (Cable/PVR Combination)
Freebox 6274
Humax 6248, 6224
Nokia 6208
Scientific Atlanta 6225
Telewest 6225
Thomson 6270
UPC 6270
Virgin Media 6225
62
En
VSX-820_PWXCN_En.book 63 ページ
2010年4月2日 金曜日 午後1時30分
Controlling the rest of your system
09
CD
Pioneer 5000, 5011
AKAI 5043
Asuka 5045
Denon 5019
Fisher 5048
Goldstar 5040
Hitachi 5042
Kenwood 5020, 5021, 5031
Luxman 5049
Marantz 5033
Onkyo 5017, 5018, 5030,
5050
Panasonic 5036
Philips 5022, 5032, 5044
RCA 5013, 5029
Roadstar 5052
Sharp 5051
Sony 5012, 5023, 5026, 5027,
5028, 5039
TEAC 5015, 5016, 5034, 5035,
5037
Technics 5041
Victor 5014
Yamaha 5024, 5025, 5038,
5046, 5047
CD-R
Pioneer 5001, 5053
Philips 5054
Yamaha 5055
Laser Disc Player
Pioneer 5002, 5003
Casette Deck
Pioneer 5058, 5059
Digital Tape
Pioneer 5057
MD
Pioneer 5056
63
En
VSX-820_PWXCN_En.book 64 ページ
10
2010年4月2日 金曜日 午後1時30分
Other connections
Chapter 10:
Other connections
CAUTION
CONTROL
• Before making or changing the connections,
switch off the power and disconnect the
power cord from the power outlet.
Plugging in components should be the last
connection you make with your system.
ON / OFF
MASTER
VOLUME
VIDEO INPUT
iPod
iPhone
MCACC
SETUP MIC
USB
VIDEO
L
AUDIO
R
• Do not allow any contact between speaker
wires from different terminals.
This receiver
Connecting an iPod
Music
iPod cable
This receiver has a dedicated iPod terminal
that will allow you to control playback of audio
content from your iPod using the controls of
this receiver.1
Genius
Playlists
Artists
Albums
Songs
Radio
Genres
Composers
Audiobooks
>
MENU



• Push down on the PUSH OPEN tab to
access the iPod terminal.
iPod
Connecting your iPod to the receiver
1 Set this receiver to the standby mode,
and then use the iPod cable to connect your
iPod to the iPod terminal on the front panel
of this receiver.
For the cable connection, refer to also the
operating instructions for iPod.
2
Switch on the receiver and your TV.
3 Switch the TV input to the input that
connects this receiver to the TV through the
corresponding composite or component
cable.
Note
1 • This system is compatible with the audio and the video of the iPod nano, iPod (fifth generation), iPod classic, iPod touch and
iPhone (iPod shuffle not supported). However, that some of the functions may be restricted for some models. Note, however,
compatibility may vary depending on the software version of your iPod and iPhone. Please be sure to use the latest available
software version.
• iPod and iPhone are licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to
reproduce.
• Features such as the equalizer cannot be controlled using this receiver, and we recommend switching the equalizer off
before connecting.
• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience
or loss of recorded material resulting from the iPod failure.
64
En
VSX-820_PWXCN_En.book 65 ページ
2010年4月2日 金曜日 午後1時30分
Other connections
4 Press iPod USB on the remote control to
switch the receiver to the iPod USB input.
The front panel display shows Loading while
the receiver verifies the connection and
retrieves data from the iPod.
10
3 Continue browsing until you arrive at
what you want to play, then press  to start
playback.3
Navigation through categories on your iPod
looks like this:
Playlists  Songs
Artists  Albums  Songs
Albums  Songs
Songs
Podcasts
Genres  Artists  Albums  Songs
Composers  Albums  Songs
Audiobooks
Shuffle Songs
5 Use the TOP MENU button to display iPod
Top menu.
When the display shows Top Menu you’re
ready to play music from the iPod.1
• If after pressing iPod the display shows NO
DEVICE, try switching off the receiver and
reconnecting the iPod to the receiver.
iPod playback
To navigate songs on your iPod, you can take
advantage of the OSD of your TV connected to
this receiver.2 You can also control all
operations for music in the front panel display
of this receiver.
Tip
• You can play all of the songs in a particular
category by selecting the All item at the top
of each category list. For example, you can
play all the songs by a particular artist.
Finding what you want to play
Basic playback controls
When your iPod is connected to this receiver,
you can browse songs stored on your iPod by
playlist, artist, album name, song name, genre
or composer, similar to using your iPod
directly.
The following table shows the basic playback
controls for your iPod:
Button
What it does

Press to start playback.
If you start playback when something
other than a song is selected, all the
songs that fall into that category will play.

Pauses playback, or restarts playback
when paused.
ENTER
Press to set the play and pause modes.
/
Press and hold during playback to start
scanning.
/
Press to skip to previous/next track.
iPod Top
[
[
[
[
[
[
[
[
[
Playlists
Artists
Albums
Songs
Podcasts
Genres
Composers
Audiobooks
Shuffle Songs
ENTER
]
]
]
]
]
]
]
]
]
Return
1 Use the / buttons to select a
category then press ENTER to browse that
category.
• To return to the previous level any time,
press RETURN.
2 Use the / buttons to browse the
selected category (e.g., albums).
• Use / to move to previous/next levels.
Press repeatedly to switch between Repeat
One, Repeat All and Repeat Off.
Note
1 The controls of your iPod (excluding the iPod touch and iPhone) will be inoperable when connected to this receiver (Pioneer
shows in the iPod display).
2 • Note that non-roman characters in the title are displayed as *.
• This feature is not available for photos or video clips on your iPod.
3 If you’re in the song category, you can also press ENTER to start playback.
65
En
VSX-820_PWXCN_En.book 66 ページ
10
2010年4月2日 金曜日 午後1時30分
Other connections
Button
What it does
Press repeatedly to switch between
Shuffle Songs, Shuffle Albums and
Shuffle Off.
DISP
Press repeatedly to change the song
(DISPLAY) playback information displayed in the
front panel display.
/
When browsing, press to move to
previous/next levels.
/
During Audiobook playback, press to
switch the playback speed: Faster 
Normal  Slower
TOP
MENU
Press to return to the iPod Top menu
screen.
RETURN
Press to return to the previous level.
2 Press iPod CTRL again to switch back to
the receiver controls when you’re done.
Tip
• Change the receiver’s input to the iPod in
one action by pressing the iPod iPhone
DIRECT CONTROL button on the front
panel to enable iPod operations on the
iPod.
About iPod
Watching photos and video content
To view photos or video on your iPod, since
video control is not possible using this receiver,
you must use the main controls of your iPod
instead.1
Important
• To play photos or video on your iPod, you
must connect the composite MONITOR
OUT jack and TV.
1 Press iPod CTRL to switch to the iPod
controls for photo and video playback.
The receiver controls will be unavailable while
you are watching iPod videos or browsing
photos.
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
“Works with iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhone and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries. iPhone is a
trademark of Apple Inc.
Note
1 • iPod photos and video content can be viewed only when the iPod is connected to the iPod VIDEO input on the front panel.
• This feature can only be used with an iPod having video output.
66
En
VSX-820_PWXCN_En.book 67 ページ
2010年4月2日 金曜日 午後1時30分
Other connections
10
Connecting a USB device
It is possible to listen to two-channel audio1
using the USB interface on the front of this
receiver. Connect a USB mass storage device2
as shown below.
Loading appears in the OSD as this receiver
starts recognizing the USB device connected.
After the recognition, a playback screen
appears in the OSD and playback starts
automatically.4
File/Folder number
• Push down on the PUSH OPEN tab to
access the USB terminal.
CONTROL
 P L AY
USB
MP3
001/004
R:Fld S:On
R e l a x Yo u r B o d y
Kevin Jackson
We a r e a l l o n e
ON / OFF
MASTER
VOLUME

32kbps
0:01
File format
Repeat or Shuffle
Song name
Artist name
Album name
Elapsed time
Return
Bit rates
VIDEO INPUT
iPod
iPhone
USB
VIDEO
L
AUDIO
R
Basic playback controls
MCACC
SETUP MIC
USB mass
storage device
This receiver
Connecting your USB device to the
receiver
1
Switch on the receiver and your TV.
2 Switch the TV input to the input that
connects this receiver to the TV through the
corresponding composite orcomponent
cable.
3 Press iPod USB on the remote control to
switch the receiver to the iPod USB input.
NO DEVICE appears in the OSD.
4 Connect your USB device.3
The USB terminal is located on the front panel.
The following table shows the basic controls on
the remote for USB playback. Press iPod USB
to switch the remote control to the iPod USB
operation mode.
Button
What it does

Starts normal playback.

Pauses/unpauses playback.
/
Press to skip to previous/next track.
/
Press and hold during playback to
start scanning.
Press repeatedly to switch between
Repeat Folder, Repeat One and
Repeat All.
Press repeatedly to switch between
Shuffle On and Shuffle Off.
DISP
Press repeatedly to change the song
(DISPLAY) playback information displayed in the
front panel display.
Note
1 This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback).
2 • Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital
audio players (MP3 players) of format FAT16/32. It is not possible to connect this receiver to a personal computer for USB
playback.
• Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no
responsibility for any loss of data that may occur when connected to this receiver.
• With large amounts of data, it may take longer for the receiver to read the contents of a USB device.
3 Make sure the receiver is in standby when disconnecting the USB device.
4 • If the file selected cannot be played back, this receiver automatically skips to the next file playable.
• When the file currently being played back has no title assigned to it, the file name is displayed in the OSD instead; when
neither the album name nor the artist name is present, the row is displayed as a blank space.
• Note that non-roman characters in the playlist are displayed as *.
67
En
VSX-820_PWXCN_En.book 68 ページ
10
2010年4月2日 金曜日 午後1時30分
Other connections
Button
What it does
/
/
During playback, press to skip to
previous/next track.
TOP MENU Press to return to the menu screen.
RETURN
Press to return to the previous level.
Other compatibility information
• VBR (variable bit rate) MP3/WMA/MPEG-4
AAC playback: Yes1
• DRM (Digital Rights Management)
protection compatible: Yes (DRM-protected
audio files will not play in this receiver.)
About MPEG-4 AAC
Important
If a USB Error message lights in the display, try
following the points below:
• Switch the receiver off, then on again.
• Reconnect the USB device with the
receiver switched off.
• Select another input source (like BD), then
switch back to iPod USB.
• Use a dedicated AC adapter (supplied with
the device) for USB power.
For more information on error messages, see
USB messages on page 77.
If this doesn’t remedy the problem, it is likely
your USB device is incompatible.
Advanced Audio Coding (AAC) is at the core of
the MPEG-4 AAC standard, which incorporates
MPEG-2 AAC, forming the basis of the MPEG-4
audio compression technology. The file format
and extension used depend on the application
used to encode the AAC file. This receiver plays
back AAC files encoded by iTunes® bearing the
extension ‘.m4a’. DRM-protected files will not
play, and files encoded with some versions of
iTunes® may not play.
Apple and iTunes are trademarks of Apple Inc.,
registered in the U.S. and other countries.
About WMA
Compressed audio compatibility
Note that although most standard bit/sampling
rate combinations for compressed audio are
compatible, some irregularly encoded files may
not play back. The list below shows compatible
formats for compressed audio files:
• MP3 (MPEG-1/2/2.5 Audio Layer 3) –
Sampling rates: 8 kHz to 48 kHz; Bit rates:
8 kbps to 320 kbps (128 kbps or higher
recommended); File extension: .mp3
• WMA (Windows Media Audio) – Sampling
rates: 32 kHz / 44.1 kHz; Bit rates: 32 kbps to
192 kbps (128 kbps or higher recommended);
File extension: .wma; WMA9 Pro and WMA
lossless encoding: No
• AAC (MPEG-4 Advanced Audio Coding) –
Sampling rates: 11.025 kHz to 48 kHz; Bit
rates: 16 kbps to 320 kbps (128 kbps or
higher recommended); File extension:
.m4a; Apple lossless encoding: No
The Windows Media logo printed on the box
indicates that this receiver can playback
Windows Media Audio content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. This
receiver plays back WMA files encoded using
Windows Media® Player bearing the extension
‘.wma’. Note that DRM-protected files will not
play, and files encoded with some versions of
Windows Media® Player may not play.
Windows Media, and the Windows logo are
trademarks or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
Note
1 Note that in some cases playback time will not be displayed correctly.
68
En
VSX-820_PWXCN_En.book 69 ページ
2010年4月2日 金曜日 午後1時30分
Other connections
10
Wireless music play
Bluetooth® ADAPTER for
Wireless Enjoyment of Music
Important
• The Bluetooth ADAPTER(PIONEER Model
No. AS-BT100) is available in the following
countries and area;
Singapore, Malaysia, Thailand, Australia,
New Zealand, Hong Kong
• Do not move the receiver with the
Bluetooth ADAPTER connected. Doing so
could cause damage or faulty contact.
Bluetooth
wireless
technology
enabled device:
cell phone
Bluetooth wireless
technology
enabled device:
Digital music
player
Device not
equipped with
Bluetooth wireless
technology:
Digital music
player
+
Bluetooth audio
transmitter
(sold commercially)
When the Bluetooth ADAPTER (Pioneer Model
No. AS-BT100) is connected to this unit, a
product equipped with Bluetooth wireless
technology (portable cell phone, digital music
player, etc.) can be used to listen to music
wirelessly.1 Also, by using a commercially
available transmitter supporting Bluetooth
wireless technology, you can listen to music on
a device not equipped with Bluetooth wireless
technology. The AS-BT100 model supports
SCMS-T contents protection, so music can
also be enjoyed on devices equipped with
SCMS-T type Bluetooth wireless technology.
Remote control operation
The remote control supplied with this unit
allows you to play and stop media, and perform
other operations.2
Connecting Optional Bluetooth
ADAPTER
• Before making or changing connections,
switch off the power.
IN BD
SUBWOOFER
PRE OUT
CD-R/TAPE DVR/VCR
ADAPTER PORT
(OUTPUT 5 V 100 mA MAX)
SURR BACK /
FRONT
HEIGHT
DVD
L
(Single)
VIDEO
DVR/VCR
OUT
IN
OUT
R
Music data
Bluetooth®
ADAPTER
This receiver
PRE OUT
TV/SAT
CD-R/TAPE DVR/VCR
CD
L
COAXIAL ASSIGNABLE
DVR/VCR
IN 1
(CD)
IN
TV/SAT
OPTICAL
OUT
IN
DVD
BD
PR
PB
L
IN 2
IN
IN 1
(CD-R/TAPE)
HDMI
MONITOR OUT DVD
ANTENNA
FM
UNBAL
75
R
ASSIGNABLE
1 2
IN
R
AUDIO
AM
LOOP
COMPONENT VID
This receiver
Bluetooth® ADAPTER
Remote control
operation
Note
1 • It must be necessary that the Bluetooth wireless technology enabled device supports A2DP profiles.
• Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology enabled devices.
2 • It must be necessary that the Bluetooth wireless technology enabled device supports AVRCP profiles.
• Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.
69
En
VSX-820_PWXCN_En.book 70 ページ
10
2010年4月2日 金曜日 午後1時30分
Other connections
1 Switch the receiver into standby and
connect Bluetooth ADAPTER to the
ADAPTER PORT located in the rear panel.
2
Switch on the receiver.
3 Press ADAPTER on the remote control to
switch the receiver to ADAPTER input.1
Pairing Bluetooth ADAPTER and
Bluetooth wireless technology
device
“Pairing” must be done before you start
playback of Bluetooth wireless technology
content using Bluetooth ADAPTER. Make sure
to perform pairing first time you operate the
system or any time pairing data is cleared.
“Pairing” is the step necessary to register
Bluetooth wireless technology device to enable
Bluetooth communications.2 For more details,
see also the operating instructions of your
Bluetooth wireless technology device.
1
Press TOP MENU.
2
Press ENTER to enter PAIRING.
4 Switch on the Bluetooth wireless
technology device that you want to make
pairing, place it near the system and set it
into the pairing mode.
5 Check to see that the Bluetooth ADAPTER
is detected by the Bluetooth wireless
technology device.
When Bluetooth wireless technology device is
connected:
Bluetooth wireless technology device name
appears in the receiver display.3
When Bluetooth wireless technology device is
not connected:
NODEVICE appears in the receiver display. In
this case, perform the connection operation
from the side of the Bluetooth wireless
technology device.
6 From the Bluetooth wireless technology
device list, select Bluetooth ADAPTER and
enter the PIN code selected in the step 4.4
3 Select the PIN code to be used from 0000/
1234/8888 using /, then press ENTER.
PAIRING blinks.
Important
• You can use any of 0000/1234/8888 PIN
codes. Bluetooth wireless technology
device using any other PIN code cannot be
used with this system.
Note
1 When the Bluetooth ADAPTER is not plugged into the ADAPTER PORT, NO ADAPTER will be displayed if ADAPTER input is
selected.
2 • Pairing is required when you first use Bluetooth wireless technology device and Bluetooth ADAPTER.
• To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology
device.
3 The system can display alphanumeric characters only. Other characters may not be displayed correctly.
4 PIN code may in some case be referred to as PASSKEY.
70
En
VSX-820_PWXCN_En.book 71 ページ
2010年4月2日 金曜日 午後1時30分
Other connections
10
Listening to Music Contents of
Bluetooth wireless technology
device with Your System
1 Press ADAPTER on the remote control to
switch the receiver to ADAPTER input.
2 Perform the connection operation from
the side of the Bluetooth wireless technology
device to the Bluetooth ADAPTER.
3 Start playback of music contents stored in
Bluetooth wireless technology device.
The following operations are now possible for
Bluetooth wireless technology devices, using
the remote controller.1
Button
What it does
/
Starts normal playback and pauses/
unpauses playback.

Press to skip to the start of the current
file, then previous files. Press and hold
to start fast reverse scanning.

Press to skip to the next file. Press and
hold to start fast forward scanning.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Pioneer
Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
Note
1 • Bluetooth wireless technology device should be compatible with AVRCP profile.
• Depending on Bluetooth wireless technology device you use, operation may differ from what is shown in this table.
71
En
VSX-820_PWXCN_En.book 72 ページ
11
2010年4月2日 金曜日 午後1時30分
Additional information
Chapter 11:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Take a look at the other
components and electrical appliances being used, because sometimes the problem may lie there.
If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer
authorized independent service company to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect
the power plug from the outlet and insert again to return to normal operating conditions.
Problem
Remedy
The power does not turn
on.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching the rear
panel. This could cause the receiver to shut off automatically.
The receiver suddenly
switches off.
• After about a minute (you won’t be able to switch the unit on during this
time), switch the receiver back on. If the message persists, call a Pioneer
authorized independent service company.
No sound is output when a • Use MASTER VOLUME to turn up the volume.
function is selected.
• Press MUTE on the remote control to turn muting off.
• Press SPEAKERS to select the proper speaker set (see Switching the
speaker system on page 20).
• Set the SIGNAL SEL to HDMI, C1/O1/O2 (DIGITAL) or A (analog)
according to the type of connections made (refer to page 33).
• Make sure the component is connected correctly (refer to Connecting
your equipment on page 16).
• Check the audio output settings of the source component.
• Refer to the instruction manual supplied with the source component.
No image is output when a • Make sure the component is connected correctly (refer to Connecting your
equipment on page 16).
function is selected.
• Use the same type of video cables for the source component and TV to
connect to this receiver (see About video outputs connection on page 22).
• Check The Input Assign menu on page 46 to make sure you’re assigned
the correct input.
• The video input selected on the TV monitor is incorrect. Refer to the
instruction manual supplied with the TV.
72
En
VSX-820_PWXCN_En.book 73 ページ
2010年4月2日 金曜日 午後1時30分
Additional information
Problem
11
Remedy
No sound from subwoofer. • Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have an
LFE channel.
• Switch the subwoofer setting in Speaker Setting on page 43 to YES or
PLUS.
• Switch the LFE ATT (LFE Attenuate) on page 40 to LFEATT 0 or LFEATT 5.
No sound from surround or • Connect the speakers properly (refer to page 18).
center speakers.
• Refer to Speaker Setting on page 43 to check the speaker settings.
• Refer to Channel Level on page 45 to check the speaker levels.
The PHASE CONTROL
feature doesn’t seem to
have an audible effect.
• If applicable, check that the lowpass filter switch on your subwoofer is
off, or the lowpass cutoff is set to the highest frequency setting. If there is
a PHASE setting on your subwoofer, set it to 0º (or depending on the
subwoofer, the setting where you think it has the best overall effect on the
sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker Distance on page 46).
Considerable noise in radio • Connect the antenna (page 27) and adjust the position for best
broadcasts.
reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 27).
• Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing noise).
Broadcast stations cannot • Connect an outdoor antenna (refer to page 27).
be selected automatically.
Noise during playback of a • Move the cassette deck away from your receiver, until the noise
cassette deck.
disappears.
No sound is output or a
• Make sure the player’s settings are correct and/or the DTS signal out is
noise is output when
on. Refer to the instruction manual supplied with the DVD player.
software with DTS is played
back.
There seems to be a time
lag between the speakers
and the output of the
subwoofer.
• See Automatically setting up for surround sound (MCACC) on page 29 to
set up your system again using MCACC (this will automatically
compensate for a delay in the subwoofer output).
After using the Auto
• Low-frequency noise could have been caused by an air conditioner or
MCACC Setup, the speaker motor. Switch off all appliances in the room and rerun the Auto MCACC
size setting (LARGE or
Setup.
SMALL) is incorrect.
73
En
VSX-820_PWXCN_En.book 74 ページ
11
74
En
2010年4月2日 金曜日 午後1時30分
Additional information
Problem
Remedy
Can’t operate the remote
control.
• Replace the batteries (refer to page 8).
• Operate within 7 m, 30° of the remote sensor (refer to page 10).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off.
• Press DIMMER on the remote control repeatedly to return to the
default.
The Bluetooth wireless
technology device cannot
be connected or operated.
Sound from the Bluetooth
wireless technology device
is not emitted or the sound
is interrupted.
• Check that no object that emits electromagnetic waves in the 2.4 GHz
band (microwave oven, wireless LAN device or Bluetooth wireless
technology apparatus) is near the unit. If such an object is near the unit,
set the unit far from it. Or, stop using the object emitting the
electromagnetic waves.
• Check that the Bluetooth wireless technology device is not too far from
the unit and that obstructions are not set between the Bluetooth wireless
technology device and the unit. Set the Bluetooth wireless technology
device and the unit so that the distance between them is less than about
10 m and no obstructions exist between them.
• Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit
are correctly connected.
• The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless technology.
Check the setting of the Bluetooth wireless technology device.
• Check that pairing is correct. The pairing setting was deleted from this
unit or the Bluetooth wireless technology device. Reset the pairing.
• Check that the profile is correct. Use a Bluetooth wireless technology
device that supports A2DP profile and AVRCP profile.
VSX-820_PWXCN_En.book 75 ページ
2010年4月2日 金曜日 午後1時30分
Additional information
11
HDMI
Symptom
Remedy
No picture or sound.
• If the problem still persists when connecting your HDMI component
directly to your monitor, please consult the component or monitor
manual or contact the manufacturer for support.
No picture.
• Video signals that are input from the analog video terminal will not
output from the HDMI terminal. Signals that are input from the HDMI
terminal will not output from the analog video terminal. Be consistent
with the type of cable between input and output.
• Depending in the output settings of the source component, it may be
outputting a video format that can’t be displayed. Change the output
settings of the source, or connect using the component or composite
jacks.
• This receiver is HDCP-compatible. Check that the components you are
connecting are also HDCP-compatible. If they are not, please connect
them using the component or composite video jacks.
• Depending on the connected source component, it’s possible that it
will not work with this receiver (even if it is HDCP-compatible). In this
case, connect using the component or composite video jacks between
source and receiver.
• If video images do not appear on your TV, try adjusting the resolution,
Deep Color or other setting for your component.
• To output signals in Deep Color, use an HDMI cable (High Speed
HDMI® Cable) to connect this receiver to a component or TV with the
Deep Color feature.
The OSD screen (System
Setup menu or the menu
screen for the iPod/USB)
isn’t displayed.
• The OSD will not appear if you have connected using the HDMI output
to your TV. Use component or composite connections when setting up
the system.
No sound, or sound
suddenly ceases.
• Check that the Audio Parameter setting is set to HDMI AMP/THRU
(refer to page 41).
• If the component is a DVI device, use a separate connection for the
audio.
• HDMI format digital audio transmissions require a longer time to be
recognized. Due to this, interruption in the audio may occur when
switching between audio formats or beginning playback.
• Turning on/off the device connected to this unit’s HDMI OUT terminal
during playback, or disconnecting/connecting the HDMI cable during
playback, may cause noise or interrupted audio.
75
En
VSX-820_PWXCN_En.book 76 ページ
11
2010年4月2日 金曜日 午後1時30分
Additional information
Important information regarding
the HDMI connection
Note
There are cases where you may not be able to
route HDMI signals through this receiver (this
depends on the HDMI equipped component
you are connecting-check with the
manufacturer for HDMI compatibility
information).
• Depending on the component, audio
output may be limited to the number of
channels available from the connected
display unit (for example audio output is
reduced to 2 channels for a monitor with
stereo audio limitations).
If you aren’t receiving HDMI signals properly
through this receiver (from your component),
please try the following configuration when
connecting up.
• If you want to switch the input source,
you’ll have to switch functions on both the
receiver and your display unit.
Configuration
Connect your HDMI-equipped component
directly to the display using an HDMI cable.
Then use the most convenient connection
(digital is recommended) for sending audio to
the receiver. See the operating instructions for
more on audio connections. Set the display
volume to minimum when using this
configuration.
• Since the sound is muted on the display
when using the HDMI connection, you
must adjust the volume on the display
every time you switch input sources.
iPod messages
Symptom
Cause
Action
iPod/USB Error 1 There is a problem with the signal path
(I/U ERR1)
from the iPod to the receiver.
Switch off the receiver and reconnect
the iPod to the receiver. If this doesn’t
seem to work, try resetting your iPod.
iPod/USB Error 2 The software version being used with the
(I/U ERR2)
iPod needs to be updated.
Update the software being used with the
iPod (please use the latest iPod software
versions later than the iPod updater
2004-10-20).
An iPod not supported by this receiver is
connected.
Connect the iPod supported by this
receiver.
iPod/USB Error 3 When there is no response from the iPod. Update the iPod software to the latest
(I/U ERR3)
version. If this doesn’t seem to work, try
resetting your iPod.
No Track
76
En
When there are no tracks in the category
selected on the iPod.
Select a different category.
VSX-820_PWXCN_En.book 77 ページ
2010年4月2日 金曜日 午後1時30分
Additional information
11
USB messages
Symptom
Cause
iPod/USB Error 1 There is a problem with the signal path
(I/U ERR1)
from the USB to the receiver.
Action
Switch off the receiver and reconnect
the USB to the receiver.
iPod/USB Error 3 When there is no response from the USB. Switch off the receiver and reconnect
(I/U ERR3)
the USB to the receiver.
iPod/USB Error 4 The power requirements of the USB
(I/U ERR4)
device are too high for this receiver.
Switch off the receiver and reconnect
the USB to the receiver.
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2 While holding down the BAND button,
press and hold the  STANDBY/ON button
for about two seconds.
3 When you see RESET? appear in the
display, press AUTO/DIRECT.
OK? shows in the display.
4 Press STEREO/ALC to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
77
En
VSX-820_PWXCN_En.book 78 ページ
11
2010年4月2日 金曜日 午後1時30分
Additional information
Miscellaneous
Specifications
Audio section
FTC power output
. . . . . . . . . . . . . . . . . . . . . . . . . . . 65 W + 65 W
(STEREO, 20 Hz to 20 kHz, 8 Ω, 0.2 %)
Rated power output (Front, Center, Surround)
. . . . . . . . 125 W per channel (1 kHz, 6 Ω, 1 %)
Maximum power output (Front, Center, Surround)
. . . . . . . 150 W per channel (1 kHz, 6 Ω, 10 %)
Total Harmonic Distortion
. . . . . . 0.06 % (20 Hz to 20 kHz, 8 Ω, 85 W/ch)
Guaranteed speaker impedance
FRONT : A, B . . . . . . . . . . . . . . . . . . 6 Ω to 16 Ω
FRONT : A+B . . . . . . . . . . . . . . . . 12 Ω to 16 Ω
SURROUND, CENTER . . . . . . . . . . 6 Ω to 16 Ω
Input (Sensitivity/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 kΩ
Output (Level/Impedance)
REC . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kΩ
Signal-to-Noise Ratio
(IHF, short circuited, A network)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB
Video section
Signal level
Composite . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Component Video . . . . . . . . . Y: 1.0 Vp-p (75 Ω)
PB, PR: 0.7 Vp-p (75 Ω)
Corresponding maximum resolution
Component Video . . .1080i (1125i)/720p (750p)
Tuner section
Frequency Range (FM) . . . 87.5 MHz to 108 MHz
Antenna Input (FM) . . . . . . . . . 75 Ω unbalanced
Frequency Range (AM)
9 kHz step . . . . . . . . . . . . .531 kHz to 1602 kHz
10 kHz step . . . . . . . . . . . .530 kHz to 1700 kHz
Antenna (AM) . . . . . . . . . . . . . . . . .Loop antenna
Digital In/Out section
HDMI terminal . . . . . . . . . . . . . . . Type A (19-pin)
HDMI output type . . . . . . . . . . . . . . . .5 V, 100 mA
USB terminal. . . . . . USB2.0 Full Speed (Type A)
iPod terminal. . . . . USB, and Video (Composite)
78
En
Power Requirements
. . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz
Power Consumption . . . . . . . . . . . . . . . . . .245 W
In standby. . . . . . . . . . . . . . . . . . . . . . . . 0.45 W
Dimensions
. . . . . 420 mm (W) x 158 mm (H) x 347.7 mm (D)
Weight (without package) . . . . . . . . . . . . . . 9.1 kg
Furnished Parts
Microphone (for Auto MCACC setup) . . . . . . . .
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . .
Dry cell batteries (AAA size IEC R03) . . . . . . .
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . .
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . .
iPod cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
These operating instructions
1
1
2
1
1
1
Note
• The specifications are applicable when the
power supply is 230 V.
• Specifications and the design are subject
to possible modifications without notice,
due to improvements.
Cleaning the unit
• Use a polishing cloth or dry cloth to wipe
off dust and dirt.
• When the surface is dirty, wipe with a soft
cloth dipped in some neutral cleanser
diluted five or six times with water, and
wrung out well, and then wipe again with a
dry cloth. Do not use furniture wax or
cleansers.
• Never use thinners, benzine, insecticide
sprays or other chemicals on or near this
unit, since these will corrode the surface.
VSX-820_PWXCN_En.book 79 ページ
2010年4月2日 金曜日 午後1時30分
Additional information
11
79
En
VSX-820_PWXCN_En.book 80 ページ
2010年4月2日 金曜日 午後1時30分
Published by Pioneer Corporation.
Copyright © 2010 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B1_En
Printed in China
<5707-00000-321-0S>