PRINTER DRIVER GUIDE

(For Macintosh

®

CP-D80DW series)

Macintosh, Apple, and Mac OS are trademarks of Apple Inc.

Adobe, Adobe Photoshop are registered trademarks of Adobe Systems.

The various software packages mentioned in this manual are the registered trademarks of their respective companies.

Refer to the following web site to check the latest version of the printer driver.

http://www.MitsubishiElectric.co.jp/vcp/support/driver_en.html

You can not use different version of the driver at the same time.

When the driver has already installed, uninstall it and then install this driver.

System requirements

Computer : PowerMacintosh G4, G5, PowerBookG4, iMac, Mac mini,

MacBook, MacBook Pro, Mac Pro

Main storage memory : 512 Mbytes or more

Hard disk

Operating system

USB *1 cable

: Empty capacity 512 Mbytes or more

: 10.5, 10.6, 10.7, 10.8, 10.9

*2

: Be sure to use a cable 2m or shorter.

* Use the printer driver in an environment that your operating system works properly.

*1: CP-D80DW series printer supports USB 2.0 (Hi-Speed USB) interface. As USB 2.0 is fully upwardcompatible with USB 1.1, CP-D80DW series printer can be used with a personal computer that supports USB 1.1 interface.

To use CP-D80DW series printer based on USB 2.0 (Hi-Speed USB), connect with a personal computer that supports USB 2.0 (Hi-Speed USB). For USB 2.0 (Hi-Speed USB) compatibility of your personal computer, contact the manufacturer of the personal computer.

*2: This printer driver supports UniversalBinary.

This printer driver is operable either on Intel-based Mac OS X or PowerPC-based Mac OS X.

1

MITSUBISHI Digital Color Printer CP-D80DW series

Installation

Administrator authority is required to install this printer driver.

When the printer driver of older version has been installed, uninstall it before installing this driver.

* Although the screen of the display is an installation screen of Mac OS X 10.6, operating procedures are the same as any other Mac OS X.

1) Start your Macintosh.

2) Double-click on “CP80MacOSX10.5” of the folder. (Fig. 1)

3) Click “Continue” button in the “Install MITSUBISHI CPD80D.” (Fig. 2)

4) Read the Software License Agreement and click “Continue” button. (Fig. 3)

<Fig. 2> <Fig. 3>

5) When you agree with the terms and conditions of the Agreement, click “Agree.” (Fig. 4)

6) Click “Install” button. (Fig. 5)

<Fig. 4> <Fig. 5>

7) Enter a name and password, and click “OK” button. (Fig. 6)

(“OK” button: “Install Software” button in Mac OS X 10.7, 10.8, or 10.9)

2

MITSUBISHI Digital Color Printer CP-D80DW series

8) Click “Continue Installation.” (Fig. 7)

9) Click “Restart” to restart the personal computer. (Fig. 8)

<Fig. 7> <Fig. 8>

10) Turn on the printer and connect it with the personal computer.

11) Click “System Preferences” to display “System Preferences” screen. (Fig. 9)

12) Click “Print & Fax” on “System Preferences screen.”

The installed printer is automatically added to the “Printers.” (Fig. 10)

(“Print & Fax”: “Print & Scan” in Mac OS X 10.7 or 10.8, and “Printers & Scanners” in Mac OS X 10.9)

* This printer is added in the name of “MITSUBISHI CPD80D.”

<Fig.9> <Fig.10>

<Notes on installation on Mac OS X 10.8 or 10.9>

The following correspondence may be necessary at the time of installation to Mac OS X 10.8 or 10.9.

Please install according to follows.

1. When attempting to install the Mac OS X driver downloaded from web site

You may receive a message window that shows “ “CP80MacOSX10.5” can’t be opened becauce it is from an unidentified developer.” during installation is displayed.

In this case, click “OK” button on this window and follow the steps below.

1) Click the installer package while holding Control key.

2) Click “Open” on the context menu.

3) Click “Open” button on the message window that shows “ “CP80MacOSX10.5” is from an unidentified developer. Are you sure want to open it?.”

Installation will start.

2. About operation after the installation completion of the driver

After the installation completion of the driver, please operate follows.

1) After completion of the driver installation, open “System Preferences” and select “Print & Scan.”

2) Select the installed printer in the printer list and click “Open Print Queue…” button.

(“Print & Scan”: “Printers & Scanners” in Mac OS X 10.9)

3) Click “Repair” button (Fig.11).

The Printer becomes available.

MITSUBISHI Digital Color Printer CP-D80DW series

3

Uninstallation

Operate the following procedures to uninstall the printer driver.

1) Start “Terminal” of “Utility” in the “Applications” folder.

2) When you do not have administrator authority, obtain it by “su” command.

3) Go to the directory where the uninstallation script (Rem80.sh) is stored and execute the script.

./Rem80.sh

4) When a password is required, enter the password for the administrator.

5) When uninstallation is completed successfully, the following message is displayed.

Uninstallation was completed.

Is a computer rebooted?” (Y/N):

6) Enter “Y” or “y” to reboot the computer.

If the computer is not rebooted automatically, exit the ongoing applications and reboot the computer manually.

Function explanation

1. Page Setup dialog

<Fig. 12 Page Setup dialog>

1) Paper Size

The size of paper is selected.

The number of print pixels for each paper size is shown in the table.

Print dots Paper size

10x15 (4x6”)

10x15 (4x6”)

5x15x2 Type1 (2x6”x2) *1

10x15 (4x6") white border *2

10x15x2 Type1 (4x6”x2)

13x13 (5x5”)

13x18 (5x7”)

13x18 (5x7”) white border *2

15x15 (6x6”)

15x20 (6x8”)

15x20 (6x8”) white border *2

5x15x2 Type2 (2x6”x2) *1

1228x1864

1086x1676

1864x2730

1524x1568

1568x2128

1380x1986

1820x1864

1864x2422

1676x2280

614x1864

*1: For the print, see “Operating directions for customer’s purpose.” printed around the image.

The print pixels vary depending on the setting of Paper Size.

2) Orientation

The direction of paper is set.

This is the standard setting function of the operation system.

3) Scale

Enlargement scale is set. (Range : 25-400%)

This is the standard setting function of the operation system.

MITSUBISHI Digital Color Printer CP-D80DW series

4

2. Print dialog

The following settings can be configured when “Feature Sets” of “Printer Features” is set to “Options” in the Print dialog.

<Fig.13 Print dialog>

1) Sharpness none / -3 / -2 / -1 / 0 / 1 / 2 / 3

Level of outline correction is changed. none :Not perform the outline correction.

-3 to 3 :The value is smaller, the outline becomes softer.

The value is larger, the outline becomes sharper.

2) PrintFinish

Printing is fi nished in matte.

Note: Matte is only recommended for an even number of 10x15 prints.

* Printing an uneven number of prints may lead to lower number of prints produced per ink ribbon kit.

3) PrintSpeed

Printing speed is set.

Fine : Printing is performed at the standard speed. (Standard quality picture)

SuperFine : Printing is performed at the speed slower than the standard speed. (High quality picture)

UltraFine : Printing is performed at the speed slower than the SuperFine speed. (Ultra high quality picture)

* When matte is selected, the Fine speed cannot be set.

Note: Fine is only recommended for an even number of 10x15 prints.

* Printing an uneven number of prints may lead to lower number of prints produced per ink ribbon kit.

4) Color conversion none / Table1 none :Color conversion is not performed.

Table1 :Color conversion is performed.

When “Feature Sets” of “Printer Features” is set to “Gamma”, “Brightness”, or “Contrast”, the menu display changes and the following settings become configurable.

5) Gamma

Adjusted value R, G, and B (-5 - +5)

Use this function to adjust the density of the middle tones.

When you want to increase the density of the middle tones, decrease the value of “Gamma”.

(Output data)

255

White Larger

Smaller

0

Black

Gamma

255(Input data)

White

6) Brightness

Adjusted value R, G, and B (-64-+64)

MITSUBISHI Digital Color Printer CP-D80DW series

5

Use this function to adjust the brightness of the print picture.

When you want to make the print picture darker, decrease the value of “Brightness”.

(Output data)

255

White

Larger

Smaller

0

Black

Brightness

255(Input data)

White

7) Contrast

Adjusted value R, G, and B (-64-+64)

Use this function to adjust the contrast of the print picture.

When you want to make the contrast of the print picture stronger, increase the value of “Contrast”.

(Output data)

255

White

Larger

Smaller

0

Black

Contrast

255(Input data)

White

3. Error indication

No.

Error dialog message

1 Printer is not connected.

2 The printer does not respond. Turn the printer Off and then On

Operation

When the error is resolved, printing restarts.

again, and try again.

3 Something is wrong with the printer.

Turn the printer Off and then On again, and try again.

4 Mechanical Error.

Set paper again.

5 Mechanical Error.

Turn the printer Off and then On again, and try again.

6 Printing unit is opened.

The print job operations of the Print Queue screen are equipped as standard in the operating system.

The buttons as follows are displayed.

Delete Job:

Hold Job:

Deletes the job being selected in the Print Queue.

Holds the job being selected in the

Print Queue.

7 Printing unit is opened while printing.

8 Ink ribbon and paper type do not match.

9 Ink ribbon is not correctly installed.

10 Ink ribbon end.

11 Paper empty.

12 The ink ribbon is not standard.

13 The printer was turned off while printing.

Turn on a printer.

14 Paper jam.

Resume Job: Resumes printing of the held job being selected in the Print Queue.

Set paper again.

15 Paper size of printer driver and ink ribbon type do not match.

16 Ink ribbon empty.

Exchange ink ribbons.

17 Paper end.

18 It is not equipped with the paper strip bin.

19 Ink ribbon error.

Set paper again.

20 Ink ribbon error.

Set paper and ink ribbon again.

* The error dialog messages are displayed in the Print Queue screen of “MITSUBISHI CPD80D” which is displayed by clicking the “Open Print Queue” button in “Print & Fax.”

* When no error message is displayed on the monitor and printing is not carried out, check the indicators on the front of the printer.

* For the details of the indicators on the printer, see the operation manual of CP-D80DW series printer.

MITSUBISHI Digital Color Printer CP-D80DW series

6

Notes

1) Secure of Hard disk for spool file

Secure the capacity of Hard disk for spool file enough for the printer operation and the number of printing sheets.

The printing cannot be correctly carried out when the capacity is running short.

The drive for spool file is the same drive as the system drive usually.

2) Operation of the printer

Refer to the operation manual of the printer.

Do not turn off the power switch during data transfer or print.

If you turn off the power switch, restarting of a computer may be needed.

When deletion of a printing data cannot be performed, restarting of a computer is required.

3) About connection of a computer and a printer

Do not disconnect the interface cable during data transfer.

If the interface cable is disconnected, wait 1 minute or more after disconnecting the cable to connect it again. If the cable is connected without leaving an enough interval, the printer driver may not work correctly.

4) System requirements for USB interface

Use a personal computer that are USB-guaranteed by the manufacturer.

CP-D80DW series printer supports USB 2.0 (Hi-Speed USB) interface. As USB 2.0 is fully upwardcompatible with USB 1.1, CP-D80DW series printer can be used with a personal computer that supports

USB 1.1 interface.

To use CP-D80DW series printer based on USB 2.0 (Hi-Speed USB), connect with a personal computer that supports USB 2.0 (Hi-Speed USB). For USB 2.0 (Hi-Speed USB) compatibility of your personal computer, contact the manufacturer of the personal computer.

5) Connection of USB cable

When you take out and insert a USB cable after installation of a printer driver, wait 10 seconds or more after extracting a cable.

If the cable is reinserted without leaving an interval, the printer may not operate normally.

6) Print job

Do not delete the print job in the spooler during data transfer. When deleting it, do not start printing until the printer becomes to the initial status.

7) Number of prints

With some applications, the number of prints set by the printer driver does not work. Set the number of prints from the print dialog box of the application.

8) Errors during printing

When an error occurs during printing, it may not be displayed on the monitor. Check the indicator on the front of the printer and take the countermeasure, and then start printing procedure again. For the indication by the indicator of the printer and the countermeasure, see the operation manual of the printer.

9) When “Resume Job” is selected after “Hold Job” is performed in the Print Queue screen, an error may not be displayed even if it occurs. In this case, select “Hold Job” and resolve the error, then click “Resume

Job” to resume printing.

10) “Add” of the “Printer List”

In some version of Mac OS X, you may not print images with the printer registered by the “Add” button.

Make the computer recognize the printer by the procedure described in “Installation.”

11) When the printer is turned off or a USB cable is not connected to the printer, the printer stauts may be displayed as standby. However, it does not affect the further printing oprations.

12) In Mac OS X 10.6, when an error job is deleted without resolving the error, the error indication in the Print

Queue may not be cancelled even if the error is resolved. In this case, delete the printer from the printer list, and then add it again to cancel the error indication.

MITSUBISHI Digital Color Printer CP-D80DW series

7

13) When the 5x15x2 (2x6”) (Type1 or Type2) is selected for the paper size

The paper cut position may shift depending on the printer.

14) When you pause or resume the printing or delete the job in the Print Queue while the printer driver is communicating with the printer such as during the printer error, the communication may fail and the deleted job may be printed.

15) When the 10x15 or 5x15x2 Type2 is selected for the paper size

When the number of printed pictures (pages) or that of copies is set to an odd number, a blank page may be printed in case of 5x15x2 Type2 and the last 1 page may be printed in case of 10x15, if you delete or pause the job in the Print Queue during the printer error.

16) When the size mismatch error occurs in Mac OS X 10.7, 10.8, or 10.9 (See 3. Error indication No.15) and the failed job is deleted in the Print Queue without resolving the error, the printing may not be started even when the next print job is sent.

In this case, connect the USB cable again. The error indication is canceld in the Print Queue.

If you keep the USB cable connected, printing is started after a while.

17) Error indication in Mac OS X 10.8 or 10.9

In Mac OS X 10.8 or 10.9 the screen displaying the error and the printing state are different from the conventional OS due to the specifications change of the OS.

In addition, when the original error dialog message is long, middle of the sentence is expressed as “…”, and the whole sentence may not be displayed.

In such cases, please refer to followings for the screen display and the whole sentence.

(No. is the No. that is shown in Table of 3. Error indication)

No.

3

2

*1

Whole sentence

The printer does not respond.

Turn the printer Off and then

On again, and try again.

Something is wrong with the printer.

Turn the printer Off and then

On again, and try again.

Error dialog message

Screen display (10.8)

The printer does not respond.

T…and then On again, and try again.

Something is wrong with the pri…and then On again, and try again.

Screen display (10.9)

Same as Mac OS X 10.8

Something is wrong with the pri…nd then On again, and try again.

5

Mechanical Error. Turn the printer Off and then On again, and try again.

Mechanical Error. Turn the print…and then On again, and try again.

Same as Mac OS X 10.8

*1: When No. 3 screen display clicks the [i] mark of the screen top, the whole sentence is displayed.

8

MITSUBISHI Digital Color Printer CP-D80DW series

Operating directions for customer’s purpose

1. When you want to adjust the color of the print image.

Set the following settings in “Feature Sets” of “Printer Features” in the Print dialog.

(Note that the effects are invalid on the display even if you make following setting.)

1) When you want the density of entire print picture to be thick (dark), decrease the value of “Brightness”.

2) When the print picture is out of focus (the contrast is weak), increase the value of “Contrast”.

The contrast becomes stronger.

3) When you want to change the color of printout.

Change the value of “Brightness”.

Increase Red

Increase Green

Increase Blue

:Increase the “R” value.

:Increase the “G” value.

:Increase the “B” value.

2. When “10x15x2 Type 1” is selected in “Paper size”

Lay out the image 1 and image 2 as following and print them.

x

Y z y Image 2

Y x y z

Print dots

2730

1864

1228

1266 y

Image 1

3. When “5x15x2 Type 1” is selected in “Paper size”

Lay out the image 1 and image 2 as following and print them.

x

Y y y

Image 2

Image 1

Y x y

Print dots

1228

1864

614

4. When “5x15x2 Type 2” is selected in “Paper size”

When multiple images are selected in “Preview”, etc., the images are printed in 5x15 (2x6”) size.

When the number of pages or copies is odd, the last print of 5x15 (2x6”) size paper is output as a blank page. Depending on the application software, a blank page may be set every other page.

Prohibition matter

We prohibit Reverse Engineering, decompiling or reverse assembling of this driver software.

Exemption from responsibility

Occasionally, this software does not operate normally depending on operating environment.

Moreover, Mitsubishi Electric Co. will not assume any responsibility for damage (including, but not limited to, lost profi t or damage caused from special circumstances etc.) occurring during the use of this driver.

9

MITSUBISHI Digital Color Printer CP-D80DW series