Ariens 991082 ZT HD48 Specifications

ZT HD
Owner/Operator Manual
Manuel Du Propriétaire/Utilisateur
Models
991082 – ZT HD48
(Serial No. 010000 and up)
991083 – ZT HD52
(Serial No. 010000 and up)
991084 – ZT HD60
(Serial No. 010000 and up)
991090 – ZT HD44
(Serial No. 010000 and up)
991091 – ZT HD60
(Serial No. 000101 and up)
Gasoline containing up to 10% ethanol (E10) or up to 10% MTBE (methyl tertiary butyl ether) is acceptable
for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) or 10% MTBE will void the product warranty.
Il est possible d’utiliser de l’essence contenant jusqu’à 10% d’éthanol (E10) ou 10% de MTBE (éther
méthyl-tertiobutylique) sur cette machine.
L’utilisation d’une essence contenant plus de 10% d’éthanol (E10) ou de 10% de MTBE annulent la
garantie.
ENGLISH
FRANÇAIS
04414600 11/11
Printed in USA
TABLE OF CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Storage . . . . . . . . . . . . . . . . . . . . . . . . . 32
Assembly . . . . . . . . . . . . . . . . . . . . . . . 12
Accessories . . . . . . . . . . . . . . . . . . . . . 32
Controls and Features. . . . . . . . . . . . . 13
Service Parts . . . . . . . . . . . . . . . . . . . . 32
Operation . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . 33
Maintenance Schedule . . . . . . . . . . . . 19
Warranty . . . . . . . . . . . . . . . . . . . . . . . . 35
Service and Adjustments . . . . . . . . . . 20
INTRODUCTION
NON-ENGLISH MANUALS
THE MANUAL
Manuals in languages other than
English may be obtained from your
Dealer. Visit your dealer or
www.gravely.com for a list of
languages available for your
equipment.
Manuals printed in languages other
than English are also available as a
free download on our website:
Before operation of unit, carefully and
completely read your manuals. The contents
will provide you with an understanding of
safety instructions and controls during normal
operation and maintenance.
All reference to left, right, front, or rear are
given from operator sitting in the operation
position and facing the direction of forward
travel.
http://www.gravely.com
ENGINE MANUAL
MANUALES EN IDIOMAS
DIFERENTES DEL INGLES
Puede obtener manuales en
idiomas diferentes del inglés en su
distribuidor. Visite a su distribuidor
o vaya a www.gravely.com para
obtener una lista de idiomas
disponibles para su equipo.
También puede imprimir manuales
en idiomas diferentes del inglés
descargándolos gratuitamente de
nuestra página Web:
http://www.gravely.com
MANUELS NON ANGLAIS
Des manuels dans différentes
langues sont disponibles chez
votre revendeur. Rendez-vous
chez votre revendeur ou allez sur
le site www.gravely.com pour
consulter la liste des langues
disponibles pour votre équipement.
Les manuels imprimés dans des
langues différentes de l’anglais
sont également disponibles en
téléchargement gratuit sur notre
site Web :
The engine on this unit is covered by a
separate manual specific to the engine. This
manual is included in the literature package
that shipped with the unit. Refer to this
manual for engine service recommendations.
If the engine manual is not available, contact
the engine manufacturer for a replacement
manual.
SERVICE AND REPLACEMENT
PARTS
When ordering publications, replacement
parts, or making service inquiries, know the
Model and Serial numbers of your unit and
engine.
Numbers are located on the product
registration form in the literature package.
They are printed on a serial number label,
located on the frame of your unit (Figure 1).
http://www.gravely.com
GB - 2
NOTE: To locate your nearest Gravely
Dealer, go to www.gravely.com.
Serial Number Label
DISCLAIMER
Gravely reserves the right to discontinue,
change, and improve its products at any time
without public notice or obligation to the
purchaser. The descriptions and
specifications contained in this manual were
in effect at printing. Equipment described
within this manual may be optional. Some
illustrations may not be applicable to your
unit.
DEALER DELIVERY
Figure 1
• Record Unit Model and Serial numbers
here.
• Record Engine Model and Serial numbers
here.
PRODUCT REGISTRATION
The Gravely dealer must register the product
at the time of purchase. Registering the
product will help the company process
warranty claims or contact you with the latest
service information. All claims meeting
requirements during the limited warranty
period will be honored, whether or not the
product registration card is returned. Keep a
proof of purchase if you do not register your
unit.
Customer Note: If the Dealer does not
register your product, please fill out, sign and
return the product registration card to Gravely
or go to www.gravely.com on the Internet.
UNAUTHORIZED REPLACEMENT
PARTS
Dealer should:
1. Test brakes after unit is assembled to be
sure adjustment has not been disturbed
in shipment (See Parking Brake
Interlock System on page 14). Wheel
brakes are properly adjusted at factory.
2. Check the safety interlock system to
make sure that it is functioning properly.
With operator on seat, unit must not start
unless steering levers are in neutral (N)
and Power Takeoff (PTO) is disengaged
(Off). Engine must stop if operator
leaves seat when steering levers are in
any drive position or PTO is engaged
(On). See Safety Interlock System on
page 14.
3. Fill out Original Purchaser Registration
Card and return the card to Gravely.
4. Explain Limited Warranty Policy.
5. Explain recommended lubrication and
maintenance. Advise customer on
adjustments. Instruct customer on
controls and operation of unit. Discuss
and emphasize the Safety Precautions.
Give customer Owner/Operator, Parts,
and Engine Manuals. Advise customer
to thoroughly read and understand them.
Customer Note: Your Dealer has been
provided complete set-up and preparation
instructions which must be completed prior to
you taking delivery of this unit. The dealer is
required to review important information in
this manual with you before or upon delivery
of the unit or attachment.
Use only Gravely replacement parts. The
replacement of any part on this equipment
with anything other than a Gravely authorized
replacement part may adversely affect the
performance, durability, and safety of this unit
and may void the warranty. Gravely disclaims
liability for any claims or damages, whether
regarding warranty, property damage,
personal injury or death arising out of the use
of unauthorized replacement parts.
GB - 3
SAFETY
WARNING: This cutting machine
is capable of amputating hands
and feet and throwing objects.
Failure to observe the safety
instructions in the manuals and
on decals could result in serious
injury or death.
Slopes are a major factor related
to loss-of-control and tip-over
accidents. Operation on all slopes
requires extra caution.
Tragic accidents can occur if the
operator is not alert to the
presence of children. Never
assume that children will remain
where you last saw them.
Gasoline is extremely flammable
and the vapors are explosive,
handle with care.
Disengage attachment, stop unit
and engine, remove key, engage
parking brake, and allow moving
parts to stop before leaving
operator’s position.
SAFETY ALERT
SYMBOL
OL1253
These are safety alert
symbols. They mean:
•ATTENTION!
•YOUR SAFETY IS
INVOLVED!
When you see this symbol:
•BECOME ALERT!
•OBEY THE MESSAGE!
OL3900
SIGNAL WORDS
The safety alert symbols above and signal
words below are used on decals and in this
manual.
Read and understand all safety messages.
WARNING: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, COULD RESULT in
death or serious injury.
CAUTION: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, MAY RESULT in minor or
moderate injury. It may also be
used to alert against unsafe
practices.
NOTATIONS
NOTE: General reference information for
proper operation and maintenance practices.
IMPORTANT: Specific procedures or
information required to prevent damage to
unit or attachment.
PRACTICES AND LAWS
Practice usual and customary safe working
precautions, for the benefit of yourself and
others. Understand and follow all safety
messages. Be alert to unsafe conditions and
the possibility of minor, moderate, or serious
injury or death. Learn applicable rules and
laws in your area, including those that may
restrict the age of the operator.
REQUIRED OPERATOR
TRAINING
Original purchaser of this unit was instructed
by the seller on safe and proper operation. If
unit is to be used by someone other than
original purchaser (loaned, rented or sold),
ALWAYS provide this manual and any
needed safety training before operation.
SAFETY DECALS AND
LOCATIONS
ALWAYS replace missing or damaged Safety
Decals. Refer to Figure 2 for Safety Decal
locations.
DANGER: IMMINENTLY
HAZARDOUS SITUATION! If not
avoided, WILL RESULT in death
or serious injury.
GB - 4
NOTE: This unit may contain any of the following safety decals.
1
11
2
10
Never fill tank when
engine is running,
hot or unit is indoors.
Never overfill fuel
tank.
P
Replace fuel cap
securely and clean
up spilled fuel.
9
08000611A
07800403
8
3
7
07800401
6
4
5
Figure 2
1. 1. Danger! TO AVOID SERIOUS
INJURY OR DEATH
NEVER CARRY
CHILDREN.
Read Owner/Operator
Manual. Allow operation
only by properly trained
adult, never children.
Go up and down slopes,
not across.
DO NOT operate on
slopes over 17°.
Keep children and others
away from unit while
operating.
Never direct discharge
toward other people.
Thrown objects can
cause injury.
Look down and behind
before and while
backing.
Keep children out of
work area and under
watchful care of a
responsible adult.
GB - 5
•
If machine stops going uphill, stop
blade and back down slowly.
•
Avoid sudden turns.
•
Keep safety devices (guards,
shields, switches, etc.) in place
and working.
•
Check interlock system per
manual before use.
•
Understand location and function
of all controls.
•
Never allow operation by untrained
persons.
2. DANGER
Do not operate mower
unless all guards are in
operating position or
bagger is attached.
DANGER!
2.3 Tipping Hazard
Read and understand the
operator’s manual before
operating unit.
Avoid tipping hazard.
2.1 Dismemberment Hazard
DO NOT operate on slopes
over 15°.
To avoid dismemberment
hazard do not put hands
near rotating blades.
DO NOT operate on slopes
over 15°.
To avoid dismemberment
hazard do not put hands
near moving belts.
2.4 Service Hazard
Keep hands away from all
rotating or moving parts.
Before servicing unit do the
following:
Keep all guards and
shields in place.
Read owners manual
before servicing or making
adjustments to unit.
2.2 Discharge Hazard
P
Discharge Hazard –
NEVER direct discharge
toward people, pets or
property. Thrown objects
can cause injury or
damage.
Set parking brake.
Remove key and
disconnect spark plug
before servicing or making
adjustments to unit.
Keep children and others
away from unit while unit is
in operation.
GB - 6
3. DANGER!
2.5 Bystander Hazard
DO NOT operate the unit in
the presence of
bystanders.
Discharge Hazard –
NEVER operate unit
without discharge chute
in operating position.
Thrown objects can
cause injury or damage.
Do not carry passengers.
Do not operate mower
unless all guards are in
operating position or
bagger is attached.
4. DANGER!
Look behind when
operating the unit in
reverse.
AVOID INJURY. Stay
clear of rotating parts.
2.6 Loss of Traction Hazard
If loss of traction is
experienced do the
following:
Disengage PTO.
Look before backing.
Proceed off slope slowly.
Do not try to turn or speed
up.
GB - 7
5. DANGER!
7. DANGER!
Discharge Hazard NEVER direct discharge
toward people, pets or
property. Thrown objects
can cause injury or
damage.
Discharge Hazard –
NEVER operate unit
without discharge chute
in operating position.
Thrown objects can
cause injury or damage.
Dismemberment Hazard –
NEVER stick hands or feet
under deck or shielded
areas.
Do not operate mower
unless all guards are in
operating position or
bagger is attached.
8. DANGER!
Shut off engine, remove
key, and read manual
before servicing or making
adjustments to unit.
Always keep feet and
hands away from rotating
parts.
Keep children and others
away from unit while unit is
in operation.
Always stand clear of
discharge area. Do not
direct discharge toward
other people
Keep feet and hands away
from all rotating or moving
parts.
Keep people away from
unit while operating.
DO NOT step or stand in
this area.
Shut off engine, remove
key, read manual before
you adjust or repair unit.
6. WARNING!
Discharge Hazard NEVER operate unit
without discharge chute
in operating position.
Thrown objects can
cause injury or damage.
NO STEP! Always keep
feet away from rotating
parts.
Do not operate mower
unless all guards are in
operating position or
bagger is attached.
9. HOT SURFACES!
DO NOT touch parts
which are hot from
operation. ALWAYS allow
parts to cool.
GB - 8
10. CAUTION!
No smoking.
MAX. FILL
Fill fuel tank to bottom of
neck – MAXIMUM.
WARNING: Over Filling may cause
severe damage to evaporative
system!
•
Never fill fuel tank when engine is
running, hot or unit is indoors. Never
overfill fuel tank.
•
Replace fuel cap securely and clean
up spilled fuel.
11. ROTATING PARTS!
AVOID INJURY. Stay
clear of rotating parts.
EMISSION CONTROL SYSTEM
This equipment and/or its engine may include
exhaust and evaporative emissions control
system components required to meet U.S.
Environmental Protection Agency (EPA)
and/or California Air Resources Board
(CARB) regulations. Tampering with
emission controls and components by
unauthorized personnel may result in severe
fines or penalties. Emission controls and
components can only be adjusted by an
Ariens Company dealer or an authorized
engine manufacturer's service center.
Contact your Ariens Company Equipment
Retailer concerning emission controls and
component questions.
SAFETY RULES
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly. Failure to follow
instructions could result in personal injury
and/or damage to unit.
ALWAYS remove key and/or wire from spark
plug before assembly. Unintentional engine
start up can cause death or serious injury.
Complete a walk around inspection of unit
and work area to understand:
• Work area • Your unit • All safety decals
Determine which attachments are needed
and can be used safely.
Inspect unit before each use for: missing or
damaged decals and shields, correctly
operating safety interlock system, and
deterioration of grass catchers. Replace or
repair as needed.
ALWAYS check overhead and side
clearances carefully before operation.
ALWAYS be aware of traffic when operating
along streets or curbs.
Keep children and people away.
Keep children out of work area and under
watchful care of a responsible adult.
Keep area of operation clear of all toys, pets,
and debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or
floors. Avoid uneven work areas and rough
terrain. Stay alert for hidden hazards or traffic.
DO NOT operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Data indicates that operators, age 60 and
above, are involved in a larger percentage of
riding mower related injuries. These
operators should evaluate their ability to
operate the riding mower safely enough to
protect themselves and others from serious
injury.
Read the entire Owner/Operator manual and
other training material. If the operator or the
mechanic cannot read the manual, it is the
owner’s responsibility to explain it to them.
Only the user can prevent and is responsible
for accidents or injuries occurring to
themselves, other people or property.
Only trained adults may operate or service
unit. Training includes actual operation.
Local regulations may restrict the age of the
operator.
NEVER allow children to operate or play on
or near unit. Be alert and shut off unit if
children enter area.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation
requires your complete and unimpaired
attention at all times.
DO NOT wear loose clothing or jewelry and
tie back hair that may get caught in rotating
parts.
Wear adequate outer garments.
NEVER wear open sandals or canvas shoes
during operation. Wear adequate safety gear,
protective gloves and footwear.
Wear proper footwear to improve footing on
slippery surfaces.
Always wear safety goggles or safety glasses
with side shields when operating mower.
GB - 9
Moving parts can cut or amputate fingers or a
hand. Wrap blade(s) or wear gloves to
service. On multiblade mowers, rotation of
one blade will cause all blades to rotate.
NEVER place your hands or any part of your
body or clothing inside or near any moving
part while unit is running.
ALWAYS keep hands and feet away from all
rotating parts during operation. Rotating parts
can cut off body parts.
ALWAYS keep body and hands away from
pin holes or nozzles which eject hydraulic
fluid under pressure.
DO NOT touch parts which are hot. Allow
parts to cool.
ALWAYS keep hands and feet away from all
pinch points.
Fumes from the engine exhaust can cause
death or serious injury. DO NOT run engine in
an enclosed area. Always provide good
ventilation.
Read, understand, and follow all instructions
in the manual and on the machine before
starting. Understand:
• How to operate all controls
• The functions of all controls
• How to STOP in an Emergency
• Braking and steering characteristics
• Turning radius and clearances
Keep safety devices or guards in place and
functioning properly. NEVER modify or
remove safety devices.
Do not operate without either entire grass
catcher or the discharge guard in place.
Stop engine before removing grass catcher or
unclogging chute.
Ensure Safety Interlock System is functioning
properly. DO NOT operate unit if safety
interlock is damaged or disabled.
Start and operate unit only when seated in
operator’s position. Steering control levers
must be in neutral, PTO disengaged and
parking brake set when starting engine.
Use care when approaching blind corners,
shrubs, trees or other objects that may
obscure vision.
Dust, smoke, fog, etc. can reduce vision and
cause an accident. Mow only in daylight or
good artificial light.
Avoid slippery surfaces. Always be sure of
your footing.
DO NOT mow on wet grass. Reduced
traction could cause sliding and effect the
machine’s stability.
Watch for traffic when operating near or
crossing roadways.
Never carry passengers.
DO NOT try to stabilize the machine by
putting your foot on the ground.
Never direct discharge towards persons or
property that may be injured or damaged by
thrown objects. Use extreme caution on
gravel surfaces.
Always stand clear of the discharge area.
ALWAYS disengage PTO, stop unit and
engine, remove key, engage parking brake
and allow moving parts to stop before leaving
operator’s position.
Never engage PTO while raising attachment
or when attachment is in raised position.
DO NOT operate at too fast a rate. DO NOT
change engine governor settings or overspeed engine. Slow down before turning.
DO NOT operate in reverse unless absolutely
necessary. ALWAYS look down and behind
before and while backing.
Stop and inspect equipment if you strike an
object or if there is an unusual vibration.
Repair, if necessary, before restarting. Never
make adjustments or repairs with the engine
running.
Mower blades are sharp and can cut you.
Wrap the blade(s) or wear gloves, and use
extra caution when servicing them. NEVER
weld or straighten mower blades.
Rotation of one blade may cause rotation of
the other blades.
Take all possible precautions when leaving
unit unattended. Shut off engine. Remove
wire from spark plug and secure it away from
spark plug.
ALWAYS remove key to prevent unauthorized
use.
Know the weight of loads. Limit loads to those
you can safely control and the unit can safely
handle.
Disengage PTO when attachment is not in
use. ALWAYS turn off power to attachment
when travelling, crossing driveways, etc.
Mow up and down slopes, not across them.
DO NOT operate on slopes of more than 15
degrees.
Operation on slopes may lead to loss of
steering control. When operating on slopes
be prepared to react to an emergency
situation:
• Return steering levers to neutral
position.
• Immediately set parking brake.
• Turn off PTO and engine.
Keep all movements on the slope slow and
gradual. Do not make sudden changes in
speed or direction.
Avoid starting or stopping on the slope. If tires
lose traction, disengage the blades and
proceed slowly straight down the slope.
If you cannot back up a slope or you feel
uneasy on it, do not mow it.
DO NOT park on slopes unless necessary.
When parking on slope always chock or block
wheels. Always set parking brake.
Use a slow speed. Tires may lose traction on
slopes even though the brakes are
functioning properly.
Do not bypass transmission when on a slope.
Tow only with a machine that has a hitch
designed for towing. Do not attach towed
equipment except at the hitch point.
GB - 10
Follow the manufacturer’s recommendations
for weight limits for towed equipment and
towing on slopes.
NEVER allow children or others in or on
towed equipment.
On slopes, the weight of the towed equipment
may cause loss of control.
Travel slowly and allow extra distance to stop.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
ALWAYS turn off power to attachment and
shut off fuel when transporting unit.
Keep unit free of debris. Clean up oil or fuel
spills.
This product is equipped with an internal
combustion type engine. DO NOT use unit on
or near any unimproved, forest-covered or
brush covered land unless exhaust system is
equipped with a spark arrester meeting
applicable local, state or federal laws. A spark
arrester, if it is used, must be maintained in
effective working order by operator.
Fuel is highly flammable and its vapors are
explosive. Handle with care. Use only an
approved gasoline container with an
appropriately sized dispensing spout.
NO smoking, NO sparks, NO flames.
ALWAYS allow engine to cool before
servicing.
NEVER fill fuel tank when engine is running
or hot from operation.
NEVER fill or drain fuel tank indoors.
Replace fuel cap securely and clean up
spilled fuel.
Properly remove fuel before tipping unit.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lockopen device.
If fuel is spilled on clothing, change clothing
immediately.
Avoid Electric Shock. Objects contacting both
battery terminals at the same time may result
in injury and unit damage. DO NOT reverse
battery connections.
Reverse connections may result in sparks
which can cause serious injury. Always
connect positive (+) lead of charger to
positive (+) terminal, and negative (-) lead to
negative (-) terminal.
ALWAYS disconnect negative (-) cable FIRST
and positive (+) cable SECOND. ALWAYS
connect positive (+) cable FIRST, and
negative (-) cable SECOND.
Explosive Gases from battery can cause
death or serious injury. Poisonous battery
fluid contains sulfuric acid and its contact with
skin, eyes or clothing can cause severe
chemical burns.
No flames, No sparks, No smoking near
battery.
ALWAYS wear safety glasses and protective
gear near battery. Use insulated tools.
DO NOT TIP battery beyond a 45° angle in
any direction.
ALWAYS keep batteries out of reach of
children.
Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer and reproductive
harm. Wash hands after handling.
ALWAYS block wheels and know all jack
stands are strong and secure and will hold
weight of unit during maintenance.
Release pressure slowly from components
with stored energy.
NEVER attempt to make any adjustments to
unit while engine is running (except where
specifically recommended). Stop engine,
remove key or spark plug wire and wait for all
moving parts to stop before servicing or
cleaning.
Check parking brake operation frequently.
Adjust and service as required.
ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler can
cause fire or explosion.
Maintain or replace safety and instruction
labels, as necessary.
NEVER store unit with fuel in fuel tank, inside
a building where any ignition sources are
present.
Shut off fuel and allow engine to cool
completely before storing in closed area or
covering unit.
Clean grass and debris from unit, especially
from around muffler and engine, to help
prevent fires.
For extended storage, shut off fuel and clean
unit thoroughly. See engine manual for proper
storage.
Lower cutting deck unless a positive
mechanical lock is used.
Use only attachments or accessories
designed for your unit.
Check all hardware at regular intervals,
especially blade attachment bolts. Keep all
hardware properly tightened.
Check attachment components frequently. If
worn or damaged, replace with
manufacturer’s recommended parts.
GB - 11
ASSEMBLY
1
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
3
2
1
UNIT ASSEMBLY
Package Contents:
Unit, Mower Deck and Literature Pack
Preparation Checklist
Refer to the Owner/Operator manual as
required.
1. Unpack Unit – Remove shrink wrap and
packaging materials.
2. Remove Unit From Container – Open
Bypass Valves (dump valves) (See
Moving the Unit with the Engine Off on
page 18).
Push unit from container onto a level
surface. Close the bypass valves.
3. Tires – See Specifications on page 33.
CAUTION: Avoid injury! Explosive
separation of tire and rim parts is
possible when they are serviced
incorrectly:
• Do not attempt to mount a
tire without the proper
equipment and experience
to perform the job.
• Do not inflate the tires
above the recommended
pressure.
• Do not weld or heat a wheel
and tire assembly. Heat can
cause an increase in air
pressure resulting in an
explosion. Welding can
structurally weaken or
deform the wheel.
• Do not stand in front or over
the tire assembly when
inflating. Use a clip-on
chuck and extension hose
long enough to allow you to
stand to one side.
1. Steering
Levers
2. Seat
3. Mounting
Hardware
OF4110
Figure 3
6. Battery – Remove battery from unit and
charge (See Battery on page 23).
7. Check Engine Crankcase – Check and
add oil if needed. See Engine Manual for
specifications.
8. Fill Engine Fuel Tank – Fill fuel tank. DO
NOT OVERFILL! See Filling Fuel Tank
on page 16.
NOTE: See engine manual for fuel type.
9. Hardware – Check for loose hardware.
10. Check Safety Interlock System – Check
to see that the interlock system operates
correctly (See Safety Interlock System
on page 14).
WARNING: FAILURE OF
INTERLOCK together with
improper operation can result in
severe personal injury.
4. Seat – See Seat Adjustments on
page 15 and Service Position on
page 20.
5. Position Steering Levers – Remove
eccentric spacers and rotate steering
levers to the operating position. Reinstall
spacers. Tighten hardware securely.
See Aligning the Steering Levers
(Figure 14) on page 25.
11. Lubrication – Lubricate all fittings per
maintenance label under seat and check
hydrostat oil level (See Lubricate Unit on
page 24).
12. On 60-inch Decks: Remove the
discharge chute from the transport
position and place the discharge chute
in the operating position.
13. Level Deck – Check unit to ensure deck
level set at factory has been maintained
(See Leveling the Mower Deck on
page 30).
14. Check Function of all Controls – Ensure
unit runs and performs properly.
GB - 12
WARNING: FAILURE OF
CONTROLS could result in death
or serious injury.
CONTROLS AND FEATURES
15
2
1
3
13
9
4
7
6
14
8
12
11
5
OM4090
OM4085
OF4410
OF4040
1. Fuel Tank and Cap
2. Steering Levers
3. Hydraulic Oil Reservoir
4. Ignition Switch
5. Hour Meter
6. Throttle Lever
7. Choke Control
8. Power Take Off (PTO) Switch
Figure 4
9. Battery
10. Mower Lift Pedal
11. Mower Deck
12. Mower Lift Lock
13. Seat Adjustment Lever
14. Parking Brake
15. Bypass Valve Lever
GB - 13
10
OPERATION
Steering Levers
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
A
B
C
D
CONTROLS AND FEATURES
See Figure 4 for Controls and Features
locations.
07757600B
Safety Interlock System
WARNING: Safety interlock
system failure and improper
operation of unit can result in
death or serious injury. Test this
system each time the unit is
operated. If this system does not
function as described, do not
operate until repairs are made.
Perform the following tests to ensure the
safety interlock system is working properly. If
the unit does not perform as stated, contact
your Gravely dealer for repairs.
NOTE: When the parking brake is engaged,
the steering levers are locked in neutral.
Test Steering PTO
Levers
Parking
Brake
Engine
STARTING INTERLOCK
1
Neutral Off
Engaged Starts
2
Neutral On
Engaged Doesn’t
Start
3
Neutral Off
Disengaged
Doesn’t
Start
The steering levers control speed and
direction. In addition, they will stop the unit.
A. For reverse travel, pull both steering
control levers backward.
B. For straight forward travel, push both
steering control levers forward.
C. To turn left, pull the left back or push
the right steering control lever forward
or a combination of both.
D. To turn right, pull the right back or
push the left steering control lever
forward or a combination of both.
To stop, return both steering levers to neutral.
NOTE: The steering controls are
mechanically locked in neutral whenever the
parking brake is engaged.
NOTE: Aggressive turning can scuff or
damage lawns. ALWAYS keep both wheels
rotating when making sharp turns. DO NOT
make turns with inside wheel completely
stopped. To obtain minimum turning radius,
slowly reverse inside wheel while moving
outside wheel slowly forward.
Ignition Switch
OPERATING INTERLOCK (ENGINE ON)
4*
Neutral On
Engaged Shuts Off
5*
Neutral Off
Disengaged
Shuts Off
* Operator lifts off seat.
OF1750
Parking Brake Interlock System
With the parking brake engaged, the steering
levers must be locked in neutral.
With the parking brake disengaged, the
engine must not start and the engine must
shut off if the operator leaves the seat.
Choke Control
OF1680
GB - 14
Operate the ignition switch
with the removable key.
The switch has three
positions: Off (1), On (2)
and Start (3). To start the
engine, turn the key to
Start, then release to On.
To stop the engine, turn
the key to Off.
Push the choke lever
forward to start a cold
engine. Pull the choke
lever to the rear when the
engine gets warm.
Throttle Lever
The throttle lever changes
the engine speed. Move
the throttle lever to Fast (1)
to increase engine speed.
Move the lever to Slow (2)
to decrease engine speed.
1
Cutting Height:
Put cutting height adjustment pin in desired
hole. Push mower lift pedal forward and hold
it while pushing down on the lift lock. Slowly
lower mower lift pedal until deck lift contacts
cutting height adjustment pin.
Parking Brake Lever
1. Pull lever up to engage
parking brake.
2. Push lever down to
disengage parking brake.
2
OF1740
OF1700
Drive
Bypass Valve Lever
Seat Adjustments
Pull the lever back to set
the pump in neutral and
move the unit with the
engine off.
Push the lever in to set the
pump in the drive position
and operate the unit.
Neutral
ON
Power Take Off (PTO)
Switch
Power take off (PTO)
switch engages and
disengages the mower
blades.
Pull the power take off
(PTO) switch to "On"
OE0261
position to engage mower
OFF
blades.
Push the power take off
(PTO) switch to "Off" position to disengage
mower blades.
NOTE: The engine will not start unless the
steering control levers are in the neutral
position, the PTO switch is in the “Off”
position and parking brake is set.
Mower Lift Pedal
OF1700
Mower lift pedal raises and lowers mower
deck for mowing or transport.
Transport:
Push mower lift pedal all the way forward until
lift lock engages.
WARNING: Make all seat
adjustments with unit stationary,
parking brake on and engine shut
off.
To adjust seat forward or backward:
1. While seated, pull seat adjustment lever
outward and slide seat into desired
position.
2. Release lever and slide seat forward or
back to lock seat into position.
Hour Meter
Press and release the toggle button to shift
between different functions.
Press and hold the toggle button to reset the
timer or clear a service message.
The hour meter has three functions:
Hour Meter: measures the amount of time
the engine has been run. This time cannot be
cleared.
Timer (TMR1): measures the time spent on
individual jobs.
Press and hold the toggle button to reset the
timer to zero. TMR1 will then start measuring
engine run time until it is reset to zero again.
Service Alert (Chg Oil, Chg H Oil & Filter,
SVC Airfilter): reminds operators of the
maintenance interval for changing the engine
oil, changing the hydraulic oil and filter and
servicing the air filter.
The alert starts counting down two hours
before the maintenance is due. The meter
flashes the word, "Now," when it reaches the
maintenance time.
Press and hold the toggle button to reset the
maintenance clock to zero after perfoming
the service.
GB - 15
NOTE: The hour meter is preprogrammed for
the initial oil change at 25 hours and for 100
hours thereafter. The hour meter is
programmed for the initial hydraulic oil and
filter change at 75 hours and for 400 hours
thereafter.
GASOLINE
Add fuel to Fuel Tank as needed. See your
Engine Manual for correct type and grade of
fuel.
IMPORTANT: ALWAYS use gasoline that
meets the following guidelines:
• Clean, fresh gasoline.
• A minimum of 87 octane/87 AKI (91
RON). High altitude use may require a
different octane. Consult your engine
manual.
• Gasoline with up to 10% ethanol
(gasohol) or up to 10% MTBE (methyl
tertiary butyl ether) is acceptable.
• Use of any gasoline other than those
approved above will void the engine
warranty. If the pumps are not marked
for the content of alcohol or ethers,
check ethanol and MTBE levels with
the fuel supplier.
• Do not modify the fuel system to use
different fuels.
• Never mix oil and gasoline.
NOTE: All gasoline is not the same. If the
engine experiences starting or performance
problems after using a new gasoline, switch
to a different fuel provider or fuel brand.
IMPORTANT: Excessively oxygenated or
reformulated fuels (fuels blended with
alcohols or ethers) can damage the fuel
system or cause performance problems. If
any undesirable operating problems occur,
use a gasoline with a lower percentage of
alcohol or ether.
To add fuel to the fuel tank:
Fuel Stabilizer
1. Clean fuel caps and surrounding area to
prevent dust, dirt, and debris from
entering fuel tanks.
2. Remove fuel caps.
IMPORTANT: Refer to Engine Manual for
correct type and grade of fuel.
3. Fill fuel tank to the bottom of filler neck.
See Specifications on page 33 for fuel
tank capacity.
IMPORTANT: DO NOT OVERFILL! This
equipment and/or its engine may include
evaporative emissions control system
components, required to meet EPA and/or
CARB regulations, that will only function
properly when the fuel tank has been filled to
the recommended level. Overfilling may
cause permanent damage to evaporative
emissions control system components. Filling
to the recommended level ensures a vapor
gap required to allow for fuel expansion. Pay
close attention while filling the fuel tank to
ensure that the recommended fuel level
inside the tank is not exceeded. Use a
portable gasoline container with an
appropriately sized dispensing spout when
filling the tank. Do not use a funnel or other
device that obstructs the view of the tank
filling process.
4. Replace fuel cap and tighten.
5. ALWAYS clean up spilled fuel.
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
Display
Toggle Button
FILLING FUEL TANK
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
PRE-START
CAUTION: Make sure all
hardware is tight, all safety
devices are in place and all
adjustments are made correctly.
1. Check Safety Interlock System
If this system does not function as described
do not operate until repairs are made.
2. Check Air Cleaner
Check air filter for dirt. Clean as required.
Follow Engine Manual Maintenance
Schedule.
GB - 16
3. Check Engine Fuel and Crankcase
Oil
4. Check Tire Pressure
To stop the engine:
1. Bring the steering levers to neutral.
Disengage the PTO and engage the
parking brake.
2. Move the throttle lever to the “Slow”
position.
3. Turn the ignition key to the “Off” position.
See Specifications on page 33 for correct tire
pressure.
TO MOW WITH UNIT
Check and add fuel if required. Check that
engine crankcase oil is full. Follow Engine
Manual Maintenance Schedule.
5. Check Hydraulic Fluid Level
See Check Hydraulic Fluid Level on page 21.
6. Adjust Seat
Be sure all controls can be reached safely
from operator’s position.
Operate the unit only when seated in the
operator’s position.
1. Start the engine. Let the engine warm
until it is running smoothly.
2. Release parking brake.
7. Set Cutting Height
WARNING: Move the steering
control levers slowly and keep the
throttle control lever at slow
speed until you learn how to
operate the unit.
Make sure the deck is set to the correct
cutting height.
STOPPING IN AN EMERGENCY
WARNING: Operating unit on
slopes may lead to loss of
steering control. When operating
on slopes be prepared to react to
an emergency situation.
1. Return steering levers to neutral position.
2. Immediately set parking brake.
3. Turn off PTO and engine.
STARTING AND SHUT OFF
CAUTION: Read entire
Owner/Operator Manual, Clutch
Manual, and Engine Manual first.
DO NOT attempt to start engine
at this time.
3. Bring the steering levers to neutral.
4. Slow the engine down to about 3/4
speed.
5. Turn ON the PTO switch to engage the
mower.
IMPORTANT: Never engage the PTO if the
mower is plugged with grass or other
material. This may cause damage to the
electric clutch.
6. Move throttle control to fast.
7. Move the steering levers forward to
obtain a slow ground speed.
8. To disengage the mower, move the PTO
switch to the “Off” position.
9. When you know how to operate the unit,
select a speed appropriate to your
mowing conditions.
PARKING
To start the engine:
1. Make sure the steering levers are in
neutral.
2. Put the PTO switch in the “Off” position.
3. Engage parking brake.
4. If the engine is cold, move the choke
control to the “On” position. If the engine
is warm or hot, do not use choke.
5. Move the throttle to 3/4 “Fast” position.
See Engine Manual for detailed
instructions.
6. Put the ignition key in the switch and
turn it to the “Start” position.
7. As soon as the engine starts, release the
key.
8. Move the choke control to the “Off”
position from the “Choke” position. Wait
until the engine is running smoothly
before operation.
To park the unit:
1. Bring the steering levers to neutral. Turn
off PTO.
2. Move the throttle lever to the “Slow”
position.
3. Engage the parking brake.
4. Lower the attachment.
5. Turn the ignition key to the “Off” position
and remove the key.
GB - 17
MOVING THE UNIT WITH THE
ENGINE OFF
FOR BEST PERFORMANCE
IMPORTANT: Never tow unit.
1. Shut OFF engine.
2. Place seat in the service position (See
Service Position on page 20).
3. Pull the right and left bypass levers to
the neutral position.
WARNING: Do not bypass
transmission when on a slope.
4. Disengage parking brake.
5. Push unit to desired location.
6. Engage parking brake.
7. Push the right and left bypass levers to
the drive position.
Cut grass when it is dry.
Keep mower blades sharp.
Keep mower deck properly levelled.
Adjust anti-scalp rollers to prevent scalping.
Do not set height of cut too low. For very tall
grass, mow twice.
Do not travel too fast.
Mow with the engine set at full throttle.
When mulching, only remove 1/3 of grass
length per cutting. Do not cut more than
1 inch (2.54 cm) at any one time.
Discharge clippings into areas already cut.
Vary cutting pattern with each mowing.
Do not allow grass or debris to collect inside
of mower deck. Clean after each use.
Push Lever In to Drive Position
Pull Lever Out to the Neutral Position
OF4105
OF4110
Figure 5
GB - 18
MAINTENANCE SCHEDULE
Proper maintenance can prolong the life of
unit. The following charts show the
recommended service schedule. More
frequent service may be required due to
working conditions (heavy loads, high
ambient temperatures, dusty conditions, or
airborne debris).
See the maintenance instructions in the
Engine Manual for additional information.
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
Period
Service
Task
Check Safety Interlock
WARNING: Safety interlock system
failure and improper operation of unit can
result in death or serious injury. Test this
system each time the unit is operated. If
this system does not function as
described, do not operate until repairs are
made. See Safety Interlock System on
page 14.
Check Parking Brake
Interlock System
See Parking Brake Interlock System on page 14.
Check Hydraulic Fluid
Check hydraulic oil level mark on cap/dipstick. Add
20W50 engine oil as needed. Do not overfill. See
Check Hydraulic Fluid Level on page 21.
Check Tires
See Specifications on page 33 for correct tire
pressure.
Each
Use
•
•
•
•
Clean Unit
CAUTION: Avoid injury! Explosive
separation of tire and rim parts is possible
when they are serviced incorrectly:
Do not attempt to mount a tire without the
proper equipment and experience to
perform the job.
Do not inflate the tires above the
recommended pressure.
Do not weld or heat a wheel and tire
assembly. Heat can cause an increase in air
pressure resulting in an explosion. Welding
can structurally weaken or deform the
wheel.
Do not stand in front or over the tire
assembly when inflating. Use a clip-on
chuck and extension hose long enough to
allow you to stand to one side.
Clean engine, battery, seat, mower deck, etc. of dirt
and debris. Do not use solvents, hard cleaners, or
abrasives.
IMPORTANT: Do not spray the unit with water,
especially when the unit is warm from operation.
Water can seep into bearings and damage them.
NOTE: Protect painted surfaces with automotive
type wax.
GB - 19
Period
Service
Task
Each
Use
Follow Engine Manual
Maintenance Schedule
Perform scheduled engine maintenance. Refer to
engine manual for detailed instructions.
Every
25
Hours
Check Mower Blades
Check mower blades for wear. Sharpen or replace
as needed. See Mower Blades on page 22.
Check Air FIlter
Check air filter for dirt. Clean as required. Follow
Engine Manual for maintenance schedule.
Lubricate Unit
Oil all pivot points and pin connections. Grease
lube fittings. See Lubricate Unit on page 24.
Check Brake Gap
Adjust gap if necessary. See Adjusting the Parking
Brake on page 26.
Clean Battery
Keep battery and its terminals clean. See Clean
Battery on page 23.
Check Fasteners
Check mower blade mounting hardware and all
other fasteners. Replace missing or damaged
fasteners. Tighten all nuts and bolts to their correct
torque value.
Check Belts
Replace worn or deteriorated belts. See Replacing
Mower Belts on page 27 and Replacing the Hydro
Pump Belt on page 28.
Change Hydraulic Fluid
and Filter*
Drain hydraulic fluid tank, replace hydraulic oil filter,
refill system. See Hydraulic Fluid on page 21.
Every
50
Hours
Every
100
Hours
Every
400
Hours
*Change hydraulic fluid and filter after the first 75 hours of operation and then
every 400 hours.
SERVICE AND ADJUSTMENTS
Gravely Dealers will provide any service which
may be required to keep your unit operating at
peak efficiency. Should engine service be
required, it can be obtained from a Gravely
Dealer or the engine manufacturer’s
authorized service center.
SERVICE POSITION
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
1. Place unit on a flat level surface.
ALWAYS stop engine. Ensure unit is
secure and will not tip over. Strap and
clamp onto lift if used.
2. Place steering levers in neutral and
engage parking brake.
3. Remove wing knob.
4. Tip seat forward (Figure 6).
CAUTION: Be sure footing is
secure to accomodate weight
shift of seat when rotating it into
service position.
CAUTION: HOT SURFACES
may result in injury. DO NOT
touch engine or drive parts which
are hot from operation. Allow
parts to cool before servicing.
5. When service is complete, lower seat
and secure with wing knob or hex nut.
GB - 20
2
1
Check Hydraulic Fluid Level
2
Check the system with the unit cold and
parked on a flat, level surface.
Then run the unit for about one minute and
recheck the levels.
To Add Hydraulic Fluid:
1. Remove the cap from the expansion
tank.
2. Fill the expansion tank with 20W-50
engine oil with an SL API classification
until oil level reaches the cold fill line on
the tank.
3. Install the expansion tank cap and then
purge the system. See Purging the
Hydraulic System on page 22.
3
4
1. Service
Position
2. Steering
Levers
The hydraulic fluid should be at the cold
fill line of the expansion tank.
3. Parking
Brake
4. Battery
Figure 6
OF4110
HYDRAULIC FLUID
WARNING: HYDRAULIC FLUID
can result in severe burns. Fluid
in hydraulic system can penetrate
skin and result in serious injury or
death.
Be sure to stop the engine before
doing any work on hydraulic
parts.
Keep body and hands away from
pin holes or nozzles which expel
hydraulic fluid when under
pressure. Use paper or
cardboard, not hands, to search
for leaks.
Ensure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to system.
FOREIGN FLUID INJECTED
INTO BODY can result in
gangrene. Fluid must be
surgically removed within a few
hours by a doctor familiar with
this form of injury.
Figure 7
Change Hydraulic Fluid and Filter
NOTE: Change hydraulic fluid and filter after
the first 75 hours of operation and then every
400 hours. Use 20W-50 engine oil with an
SL API classification.
1. Place container under oil filter to catch
oil.
2. Remove the filter guard and oil filter from
the transaxle.
3. Remove the oil drain plug or fitting from
the inlet port and allow the transaxle to
drain completely.
4. Clean the filter mounting surface and
then lubricate rubber gasket on new oil
filter with clean hydraulic oil.
5. Spin new oil filter onto filter housing until
it makes contact. Tighten oil filter
another 3/4 turn.
6. Install the filter guards removed in
step 2. Tighten the mounting screws to
65 lbf-in (7.3 N•m).
GB - 21
7. Fill with 20W-50 engine oil with an SL
API classification until oil appears at the
bottom of the drain plug (about 2 quarts
per transaxle). Install the drain plug and
tighten it to 180 lbf-in (20.3 N•m).
8. Repeat steps 1 – 7 for the other
transaxle.
9. Follow the instructions in To Add
Hydraulic Fluid: on page 21.
MOWER BLADES
2
1
5. Start the engine and slowly move the
steering levers in forward and reverse
five or six times.
6. Stop the engine, check the oil level and
add oil as needed.
7. Repeat steps 2 – 6 until the transaxles
operate smoothly in forward and reverse
at normal speeds without excessive
noise.
Remove
CAUTION: Use sturdy gloves or
padding to protect hands when
working with mower blades.
3
1. Turn the engine off. Remove the ignition
key. Remove the ignition wire from the
spark plugs.
2. Remove the bolts, cup washer, and
blades from the spindle shafts.
Replace
4
1.
2.
3.
4.
1. Put the blades, cup washers, and the
bolts back on the spindle shafts.
2. Tighten the bolts to a torque of
115 – 160 lbf-ft (156 – 217 N•m).
3. Replace the ignition wire on the spark
plugs.
Drain Plug
Oil Filter
Filter Guard
Mounting Hardware
Figure 8
Purging the Hydraulic System
WARNING: This adjustment
requires operating the engine.
Use extreme care to avoid
contact with moving parts and hot
surfaces. Be sure rear of unit is
well supported and secure before
starting engine.
1
2
1. With the unit up to and facing a wall, jack
up the unit so that both drive wheels are
off the ground.
2. Disengage the parking brake and put the
transaxle bypass levers in the neutral
position. See Moving the Unit with the
Engine Off on page 18.
3. Start the engine and slowly move the
steering levers in forward and reverse
five or six times.
4. Stop the engine and put the transaxle
bypass levers in the drive position. See
Moving the Unit with the Engine Off on
page 18.
GB - 22
3
1. Blade
2. Cup Washer
3. Bolt
Figure 9
BATTERY
Sharpen the Mower Blades
CAUTION: DO NOT sharpen
mower blades while on unit. An
unbalanced mower blade will
cause excessive vibration and
eventual damage to unit. Check
mower blade balance before
reinstalling blades.
NEVER weld or straighten bent
blades.
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
1. Remove mower blade from unit.
Discard mower blade if:
• More than 1/2 in. (1.27 cm) of metal is
removed.
• Air lifts become eroded.
• Blade is bent or broken.
2. Sharpen mower blade by removing an
equal amount of material from each end
of mower blade. DO NOT change angle
of cutting edge or round the corner of the
mower blade.
3. Check mower blade balance.
Slide mower blade on an unthreaded
bolt. A balanced blade should remain in
a horizontal position. If either end of
mower blade moves downward, sharpen
the heavy end until blade is balanced.
4. Install mower blade(s) on unit.
5. Tighten the bolts to a torque of 115 –
160 lbf-ft (156 – 217 N•m).
WARNING: Battery posts,
terminals and related accessories
contain lead and lead
compounds, chemicals known to
the State of California to cause
cancer and reproductive harm.
Wash hands after handling.
Unit comes equipped with a maintenancefree battery that requires no regular
maintenance except cleaning the terminals.
Remove Battery
1. Shut OFF engine. Engage parking
brake. Remove the ignition key.
2. Place seat in the service position (See
Maintenance Schedule on page 19).
3. Disconnect cables from battery
(negative, then positive) (Figure 11).
4. Remove hold down and remove battery.
Replace Battery
1. Replace battery and secure with battery
hold down.
2. Reconnect cables to battery (positive,
then negative). Position boot over
positive terminal.
3. Return seat to operating position.
DO NOT Sharpen to This Pattern
1
Clean Battery
Keep battery and its terminals clean. Inspect
every 100 operating hours or monthly for best
performance.
2
4
DISCARD if more than
1/2 in. (1.27 cm)
1
3
OT0792
4
Sharpen to this pattern
1. Cutting Edge
3. Air Lift
Erosion
2. Square
Corner
4. Air Lift
Figure 10
GB - 23
3. Connect positive (+) lead of charger to
positive (+) terminal, and negative (–)
lead to negative (–) terminal.
4. Charge battery according to charger and
battery manufacturers’ instructions.
5. Replace battery. See Replace Battery on
page 23.
2
1
Jump-Starting
Gravely does not recommend jump-starting
your unit. Jump-starting can damage engine
and electrical system components. See your
engine manual for more detailed information.
3
LUBRICATE UNIT
OF1671
Apply oil at all pivot points and pin
connections.
1. Negative terminal
2. Positive terminal
3. Battery
Figure 11
1
1. Remove battery from unit. See Remove
Battery on page 23.
2. Clean terminals and battery cable ends
with wire brush.
3. Coat terminals with dielectric grease or
petroleum jelly.
4. Replace battery. See Replace Battery on
page 23.
OF1794
R LUBRICA- QTY
E
TION
F
1 REPACK
2
Charging the Battery
Battery Electrolyte First Aid
OIL
Follow First Aid directions for contact with
battery fluid.
• External Contact: Flush with water.
• Eyes: Flush with water for at least 15
minutes and get medical attention
immediately!
• Internal Contact: Drink large quantities
of water. Follow with Milk of Magnesia,
beaten egg or vegetable oil. Get
medical attention immediately!
In case of internal contact, DO NOT induce
vomiting!
LOCATION
INTERVAL
400 Hrs
CASTER
PIVOT
ALL PIVOT 50 Hrs
POINTS, PIN
CONNECTIONS
Figure 12
STEERING CONTROL NEUTRAL
ADJUSTMENT
Eliminating Excessive Creeping of
the Unit (Figure 13)
IMPORTANT: DO NOT fast charge. Charging
at a higher rate will damage or destroy
battery. ONLY use an automatic charger
designed for use with your battery.
ALWAYS follow information provided on
battery by battery manufacturer. Contact
battery manufacturer for extensive
instructions to charge battery.
1. Remove battery from unit. See Remove
Battery on page 23.
2. Place battery on bench or other wellventilated place.
GB - 24
WARNING: This adjustment
requires operating the engine.
Use extreme care to avoid
contact with moving parts and hot
surfaces. Be sure rear of unit is
well supported and secure before
starting engine.
1. If hydraulic system is cold, run unit for a
minimum of five minutes, then shut OFF
engine.
2. With the unit up to and facing a wall, jack
up the unit so that both drive wheels are
off the ground.
3. Remove the drive wheels from the unit.
4. Start the engine, run engine at full
throttle, and release the parking brake.
5. Move the steering levers from Forward
to Reverse several times to make sure
controls are free. Then return steering
levers to neutral position.
6. Check wheel(s) for movement.
NOTE: The right and left hydraulic pumps are
adjusted the same way.
7. If a wheel moves, adjust the return to
neutral mechanism on the hydraulic
pump:
a. Loosen the return to neutral screw
on the pump.
b. Slowly move the speed and
direction control bracket clockwise
or counterclockwise until the
wheel stops moving.
c. Hold the stop bracket in position
and tighten the return to neutral
screw on the pump.
8. Move steering levers from Forward to
Reverse several times and return
steering levers to neutral position.
Check wheel(s) for movement.
9. If wheel is still moving, repeat steps 7
and 8.
10. Shut OFF engine.
11. Replace drive wheels.
Aligning the Steering Levers
(Figure 14)
1. Shut OFF engine. Engage parking
brake. Remove the ignition key.
2. Place seat in the service position (See
Service Position on page 20).
3. Loosen brake interlock on the same side
as steering lever to be adjusted.
4. Loosen tie rod jam nuts and turn tie rod
until steering levers are aligned.
5. Tighten jam nut on tie rod, tighten brake
interlock.
3
1
2
4
Axle Direction
Return to Neutral
Adjusting Screw
5
1
1. Tie-Rod Jam
Nut
2. Tie-Rod
3. Steering
Lever
Speed and
Direction
Control Arm
Figure 14
Figure 13
GB - 25
4. Brake
Interlock
5. Hydrostatic
Transmission
OF3381
ADJUSTING THE UNIT TO TRACK
STRAIGHT
ADJUSTING THE HEIGHT OF THE
STEERING LEVER HANDLES
The handles have three height positions
(Figure 16).
WARNING: Prior to adjusting the
tracking of the unit, shut OFF
engine, engage parking brake,
and remove the ignition key.
2
Check and adjust tire pressure. Increase
pressure on side unit tracks to. DO NOT
exceed maximum recommended tire
pressure (See Specifications on page 33).
If tire pressure adjustment does not solve
tracking problem, adjust the limiter bolts on
the stop bracket (Figure 15). Front bolts
adjust forward and rear bolts adjust reverse.
Lengthen the limiter bolt (move closer to
lever) on side which is too fast.
2
1
1
Position # 1
Position # 2
Position # 3
3
3
2
1
4
1. Spacer
2. Handle
3. Eccentric
Spacer
4. Steering Lever
Figure 16
4
1. Limiter Bolt
4. Stop
Bracket
2. Jam Nut
3. Steering
Lever
Figure 15
OF0004
1. Shut OFF engine. Engage parking
brake. Remove the ignition key.
2. Remove the spacer, handle, and
eccentric spacer from the steering lever.
NOTE: Position the right and left handles at
the same height position.
3. Install the spacer, handle, and eccentric
spacer in the appropriate height position.
Do not tighten the nut holding the
eccentric spacer.
4. Turn the eccentric spacer until the right
and left handles are the same height.
Tighten nut.
ADJUSTING THE PARKING
BRAKE
The parking brake should not need
adjustment, however if the parking brake
does not hold the unit properly, the brake may
need adjustment.
GB - 26
Check Adjustment
NOTE: Be sure to check the parking brake on
both sides of the unit (Figure 17).
1. Engage parking brake and set both
transmission bypass valves to the
neutral position. See Moving the Unit
with the Engine Off on page 18.
2. Push the unit forward.
If the unit easily rolls forward the
transmission brakes are not fully
engaging. Tighten the brake cable to
fully engage the brake lever on the
transmission.
CAUTION: DAMAGED OR
WORN BELTS may result in
injury and/or damage to unit.
Check belts for excessive wear or
cracks often.
PTO Belt Access
1. Properly stop and park unit (See
Operation on page 14).
2. Lower the mower.
3. Place seat in most rearward position.
4. Remove belt covers.
5. Place foot board in open position
(Figure 18).
Adjust the Parking Brake
1. Disengage the parking brake.
2. Loosen the nuts on the parking brake
cable adjuster and then turn the adjuster
until the cable is taut, not tight.
3. Engage the parking brake and check the
adjustment. Repeat as needed.
4. Tighten the nuts.
NOTE: Set both bypass valves to the drive
position when finished adjusting the brake.
1
2
1
2
3
1. Footboard in
open position
2. Support Frame
3. Pivot
Figure 18
Replacing Mower Belts
3
NOTE: Long mower belt must be removed to
remove short mower belt.
1. Parking Brake Cable
2. Adjuster
3. Nuts
Figure 17
CAUTION: Use care when
releasing idler spring tension.
Keep body parts well away from
idlers when performing this
operation.
PTO BELT
1. Slowly release the tension on the long
mower belt idler until all the tension is
removed from the springs.
2. Remove long mower belt from left blade
spindle and remove from deck.
3. Slowly release the tension on the short
belt idler until all the tension is removed
from the springs.
WARNING: MOVING PARTS can
cut or amputate body parts.
ALWAYS wait for moving parts to
stop before performing
maintenance or service.
GB - 27
4. Remove short mower belt from right
blade spindle and from deck. Idler pivot
bolt must be loosened slightly to gain
clearance to remove belt from under
idler pulley (Figure 19).
5. Arrange new mower belt(s) on deck
(short belt first). Retighten short mower
belt idler pivot bolt. Install belts on
sheaves. Put belts onto center sheave
last.
NOTE: The PTO idler spring length range is
12.25 – 12.5 in. (31 – 31.8 cm) measured at
a 3 in. (7.62 cm) cutting height. Adjust the
idler spring length as needed, see Figure 20.
6. Replace belt covers and return foot
board to closed position.
3
PTO Idler Spring Length
Measure PTO
idler spring
length here.
2
The PTO idler spring length range is
12.25 – 12.5 in. (31 – 31.8 cm) measured
at a 3 in. (7.62 cm) cutting height. Adjust
as necessary.
Figure 20
5
4
1
Replacing the Hydro Pump Belt
1. Properly stop and park unit (See
Operation on page 14).
2. Remove the PTO belt from the mower
clutch sheave (See Replacing Mower
Belts on page 27).
7
6
1.
2.
3.
4.
5.
6.
7.
OF4345
CAUTION: Use care when
releasing idler spring tension.
Keep body parts well away from
idlers when performing this
operation.
PTO Mower Belt
Mower Drive Belt
Springs
Mower Drive Belt Idler
PTO Mower Belt Idler
Mower Clutch Sheave
Center Sheave
3. Slowly release the tension on the hydro
pump belt idler until all the tension is
removed from the springs.
4. Remove old hydro pump belt from right
hand hydrostat sheave first (Figure 21).
5. Install new hydro pump belt by
positioning belt on sheaves. Put belt
onto right hand hydrostat sheave last.
6. Replace long mower belt on mower
clutch sheave. See Replacing Mower
Belts on page 27.
Figure 19
GB - 28
Lowest Cutting
Height
1
2
Highest
Cutting
Height
6
5
OF3590
Figure 22
Removing the Mower Deck
3
1. Remove PTO belt (See Replacing
Mower Belts on page 27).
WARNING: AVOID INJURY.
Mower lift arms and mower lift
pedal could cause severe injury if
they are not locked before
removing the mower deck.
ALWAYS lock mower deck lift
before removing the deck.
7
4
8
OF1631
1.
2.
3.
4.
Hydro Belt
Spring
Idler
Engine
Sheave
5. Right Hand
Hydrostat
6. Left Hand
Hydrostat
7. Clutch
8. Clutch
Anchor
2. Lock the mower deck in the service
position.
Push the mower lift pedal forward
between cutting height number 4 and
number 5 to align the holes in the deck
lift shaft and the deck lift cover. Insert the
cutting height pin in the holes on the side
of the deck lift cover so it passes all the
way through the deck lift cover and
shaft.
Figure 21
MOWER DECKS
Anti-scalp Roller Adjustment
The anti-scalp rollers are set at the factory for
typical mowing height, but can be adjusted for
high or low cutting conditions (Figure 22).
Anti-Scalp rollers are intended to prevent
lawn scalping, not to control cutting height.
For a very high cutting height, set the antiscalp rollers in the lowest position on the
bracket.
For a very low cutting height, set the antiscalp rollers in the highest position on the
bracket.
NOTE: There are four anti-scalp rollers on
the outside of the mower deck and four antiscalp rollers on the inside of the mower deck.
Make sure all anti-scalp rollers are set at the
same height.
IMPORTANT: The mower lift arms are not
locked unless the cutting height adjustment
pin passes all the way through both the deck
lift cover and shaft.
NOTE: Support the mower deck on blocks or
jack stands before disconnecting link chains
from mower lift arms to prevent the deck from
falling.
3. Remove link chains from mower lift
arms. Note hole location on mower lift
arms for replacement.
4. Remove the mower mounting pins
connecting the mower mounting arms to
the deck.
5. Slide mower deck out from under unit.
GB - 29
Check Blade Level and Pitch
1
5
1
2
2
3
4
1. Mower Lift
Arm
2. Link Chain
3. Mower
Mounting
Arm
4. Mower
Mounting
Pin
5. Mower Lift
Arms
Locked
Figure 23
OF3765
Installing the Mower Deck (Figure 23)
1. Slide mower deck under unit.
2. Connect mower mounting arms to deck
with mower mounting pins.
3. Install link chains on the mower lift arms
in the same holes they were removed
from.
4. Install PTO mower belt (See Replacing
Mower Belts on page 27).
5. Level mower deck (See Leveling the
Mower Deck on page 30).
Leveling the Mower Deck
1. Raise mower deck to a 3 in. (7.62 cm)
cutting height.
2. Shut off engine. Engage parking brake.
Remove the ignition key.
NOTE: Place blocks under the bottom edge
of the deck, not under the reinforcement bar
welded along deck face.
3. Place blocks at each corner of the deck
to support the weight of the deck.
4. Turn the blades so the blade ends point
left to right across the width of the deck.
5. Measure the distance between the
ground and cutting edge of the blade on
the left blade (Left position in Figure 24)
and on the right blade (Right position in
Figure 24). Distances should be within
3/16 in. (4.7 mm). If they are not, raise
the low side of the deck using the height
adjusters on the deck lift brackets (see
Figure 25).
6. After deck is level side to side, check the
deck front to back pitch.
7. Turn the blades so the blade ends point
front to back as shown in Figure 24.
8. Measure the distance between the
ground and the cutting edge of the
middle blade at the front of the deck
(Front position in Figure 24) and
between the ground the cutting edge of
the left and right blades at the rear of the
deck (Rear position in Figure 24).
9. The cutting edge at the front of the deck
(Front position in Figure 24) should be
1/8 in. (3.18 mm) lower than the cutting
edges at the rear of the deck (Rear
position in Figure 24).
10. If measurements are out of range, raise
the low side of the deck using the height
adjusters on the deck lift brackets (see
Figure 25). Be sure to raise the deck
evenly to keep the deck level side to
side.
NOTE: Pitching the front of the blades lower
than the rear provides a balance between cut
quality and the power needed to cut grass.
Certain cutting conditions require the deck to
be pitched with the rear of the blades lower
than the front. Heeling the deck this way
requires more engine power but can provide
better cut quality.
11. Remove the blocks from under the deck.
These adjustments should be made on a
level surface with the tires inflated to the
correct air pressure.
GB - 30
CLUTCH ADJUSTMENT
Blade Side-to-Side Level
Right
Left
Blade Front-to-Back Pitch
Front
Rear
Rear
Figure 24
Adjust Blade Height
Level and pitch the mower with the height
adjusters on each deck lift bracket
(Figure 25).
Loosen the jam nut on the deck lift
bracket bolt about 1/4 turn to reduce
clamp load on the height adjusters.
Loosen the jam nut on the deck adjuster
bolt and then turn the bolt clockwise to
raise the deck or counterclockwise to
lower the deck. Tighten both jam nuts.
If clutch fails to engage or disengage properly
or begins to make abnormal noise, check the
air gap adjustment at the three inspection
slots.
To check:
1. Stop engine, remove key and wait for all
hot parts to cool.
2. Measure the air gap between the
armature and the rotor.
Minimum: A .016" feeler gauge should
slide between armature and rotor with
slight contact.
Maximum: A .020" feeler gauge should
slide between armature and rotor with
slight contact.
3. Repeat for each inspection slot.
To adjust:
1. If necessary, loosen gap adjustment
nuts until a .016" feeler gauge fits
between armature and rotor.
2. Slide a .020" feeler gauge between
armature and rotor.
3. Tighten gap adjustment nut until there is
slight contact on feeler gauge.
4. Repeat steps 1 – 3 at each inspection
slot.
NOTE: Adjust air gap as evenly as possible.
5. Start unit, engage and disengage PTO.
6. Shut off unit.
7. Recheck air gap and adjust if needed.
4
Height Adjusters
3
1. Armature
2. Rotor
DO NOT place blocks under
reinforcement bar.
Figure 25
GB - 31
4
2
1
3. Inspection Slot
4. Gap Adjustment
Nut
Figure 26
OG1500
ACCESSORIES
STORAGE
WARNING: AVOID INJURY.
Read and understand entire
Safety section before proceeding.
SHORT TERM
NEVER spray unit with high-pressure water
or store unit outdoors.
Inspect unit for visible signs of wear,
breakage or damage.
Keep all nuts, bolts and screws properly
tightened and know unit is in safe working
condition.
Store unit in a cool, dry protected area.
LONG TERM
Clean unit thoroughly with mild soap and low
pressure water and lubricate (See Lubricate
Unit on page 24 in Maintenance). Touch up
all scratched painted surfaces.
Remove weight from wheels by putting
blocks under frame or axle.
When storing unit for extended periods of
time, remove all fuel from tank and carburetor
(run dry). Refer to Engine Manual.
Clean and charge the battery. Charge battery
every three to four weeks when storing unit.
Fuel System
Gasoline left in the fuel system for extended
periods without a stabilizer will deteriorate,
resulting in gum deposits in the system.
These deposits can damage the carburetor
and the fuel hoses, filter and tank. Prevent
deposits from forming in the fuel system
during storage by adding a quality fuel
stabilizer to the fuel. Follow the
recommended mix ratio found on the fuel
stabilizer container.
To treat the fuel system for storage:
1. Add fuel stabilizer according to
manufacturers’ instructions.
2. Run engine for at least 10 minutes after
adding stabilizer to allow it to reach the
carburetor.
NEVER store the engine with fuel in the fuel
tank inside of a building with potential
sources of ignition.
To Take the Unit Out of Storage
1. Refer to the engine service manual to
prepare the engine for service.
2. Put fresh, clean fuel in the fuel tank.
3. Begin the maintenance schedule.
4. Charge and install the battery.
Part No.
Description
79100400
Mulching Kit 48-inch Decks
79206400
Mulching Kit 52-inch Decks
79206500
Mulching Kit 60-inch Decks
79206700
Striper Kit
79100700
Discharge Cover Kit 48-inch
Decks
79100800
Discharge Cover Kit 52-inch
Decks
79206800
Discharge Cover Kit 60-inch
Decks
79202700
Headlight Kit
79102500
Bagger Adapter Kit 60-inch Decks
79102600
Bagger Adapter Kit 52-inch Decks
79102700
Bagger Adapter Kit 48-inch Decks
89100300
HD Series Bagger
SERVICE PARTS
Part No.
Qty
Description
21547900
1
Fuel Filter (991082, 083,
084, 090)
21545700
1
Fuel Filter (991091)
21548000
1
Air Filter (991082, 083,
084, 090)
21545800
1
Air Filter (991091)
21545900
1
Air Pre-Cleaner (991091)
21397200
1
Engine Oil Filter (991091)
21548100
1
Engine Oil Filter (991082,
083, 084, 090)
21545100
2
Hydraulic Oil Filter
21547800
2
Spark Plug (991082, 083,
084, 090)
21544000
2
Spark Plug (991091)
07200025
1
PTO Belt – 48-inch Decks
07200026
1
PTO Belt – 52-inch Decks
07200028
1
PTO Belt – 60-inch Decks
07211500
1
Traction (Hydro Pump) Belt
00450200
1
Blade – 48-inch Decks
03253800
1
Blade – 52-inch Decks
03253900
1
Blade – 60-inch Decks
GB - 32
SPECIFICATIONS
Model Number
Model
Engine
Engine Model Number
Engine Displacement – in3 (cc)
Governed RPM (May be
different from maximum RPM)
Liquid or Air Cooled
Speed
Forward Maximum – mph
(km/h)
Reverse Maximum – mph
(km/h)
Turning Radius
Brakes
Electrical
Starter
Battery
Power Take-Off
Fuel
Fuel Type
Fuel Tank Capacity – gal. (L)
Transmission
Type
Transmission Oil
Hydraulic Oil Filter
Size and Weight
Length – in. (cm)
Width (With Chute Up) – in.
(cm)
Height – in. (cm)
Weight – lbs (kg)
Tires
Front Tire Size – in.
Rear Tire Size – in.
Front Tire Pressure – psi (kPa)
Rear Tire Pressure – psi (kPa)
Mower Deck
Mower Deck Lift
Cutting Width – in. (cm)
Cutting Height – in. (cm)
Cutting Height Increments – in.
(cm)
991082
HD 48
991083
HD 52
Kawasaki
FR730
44.3 (726)
3,600 ± 75
Air
8.0 (12.9)
4.0 (6.4)
Zero
Hydro – Parking
Electric
12-Volt Maintenance Free U1-250
Electric PTO Clutch/Brake
Refer to Engine Manual
6.5 (24.6)
Hydrostatic Drive
Use 20W-50 engine oil with an SL API
classification
Yes
71.5 (181.6)
50 (127)
55.5 (141)
42 (106)
823 (373.9)
832 (377.4)
13 x 5-6
20 x 10-10
20 – 25 (138 – 172)
15 – 18 (103 – 124)
Mechanical
48 (121.9)
52 (132.1)
1 – 5 (2.5 – 12.7)
0.5 (1.25)
GB - 33
SPECIFICATIONS
Model Number
Model
Engine
Engine Model Number
Engine Displacement – in3 (cc)
Governed RPM (May be
different from maximum RPM)
Liquid or Air Cooled
Speed
Forward Maximum – mph
(km/h)
Reverse Maximum – mph
(km/h)
Turning Radius
Brakes
Electrical
Starter
Battery
Power Take-Off
Fuel
Fuel Type
Fuel Tank Capacity – gal. (L)
Transmission
Type
Transmission Oil
Hydraulic Oil Filter
Size and Weight
Length – in. (cm)
Width (With Chute Up) – in.
(cm)
Height – in. (cm)
Weight – lbs (kg)
Tires
Front Tire Size – in.
Rear Tire Size – in.
Front Tire Pressure – psi (kPa)
Rear Tire Pressure – psi (kPa)
Mower Deck
Mower Deck Lift
Cutting Width – in. (cm)
Cutting Height – in. (cm)
Cutting Height Increments – in.
(cm)
991084
HD 60
991090
HD 44
991091
HD 60
FR691
Courage Pro
Kohler
Kawasaki
FR730
44.3 (726)
44.2 (725)
3 600 ± 75
Air
8.0 (12.9)
4.0 (6.4)
Zero
Hydro – Parking
Electric
12-Volt Maintenance Free U1-250
Electric PTO Clutch/Brake
Refer to Engine Manual
6.5 (24.6)
Hydrostatic Drive
Use 20W-50 engine oil with an SL API classification
Yes
71.5 (181.6)
62.8 (159.5)
46.8 (118.9)
62.8 (159.5)
853 (386.9)
42 (106)
818 (373.3)
853 (386.9)
13 x 5-6
20 x 10-10
20 – 25 (138 – 172)
15 – 18 (103 – 124)
60 (152.4)
Mechanical
44 (111.8)
1 – 5 (2.5 – 12.7)
0.5 (1.25)
GB - 34
60 (152.4)
Consumer Mowing Equipment
Limited Warranty
Ariens Company (Ariens) warrants to the original purchaser that Ariens, Gravely and Countax brand lawn
and garden consumer products purchased on or after 1/1/2011 will be free from defects in material and
workmanship for the time period noted in the chart below. Equipment put to personal use around a single
household or residence is considered “Consumer Use”; equipment put to any business use (agricultural,
commercial, or industrial) or used at multiple locations is considered “Commercial Use.” If any product is
rented or leased, then the duration of these warranties shall be 90 days after the date of purchase.
An authorized Ariens dealer (Ariens brand products), Gravely dealer (Gravely brand products), or Countax
dealer (Countax brand products) will repair any defect in material or workmanship, and repair or replace any
defective part, subject to the conditions, limitations and exclusions set forth herein. Such repair or
replacement will be free of charge (labor and parts) to the original purchaser except as noted below.
Warranty
Code
Product Group
Warranty Period
Consumer Use
Warranty Period
Commercial Use
HA
Zoom & ZT Zero-Turn Riders;
AMP™ Rider
3 Years
90 Days
HB
Max Zoom & ZT HD Zero-Turn Riders
3 Years
1 Year
HC
Tractors, "961" Series Walk-Behind
Mowers
2 Years
90 Days
HD
Classic LM Series Mowers; Wide Area
Walk Mowers
3 Years
90 Days
N/A
Service (replacement) Parts
90 Days (no labor)
90 Days (no labor)
Special Extensions
The chart below details special extensions to this warranty:
Warranty
Code
Warranty Exception
Warranty
Period
Use
Detail
HA, HB
Mower Deck Shell on
Zero-Turn Riders
5 Years
Consumer
3 years parts and labor
Additional 2 years parts only
HA, HB
Main Frame on
Zero-Turn Riders
5 Years
Consumer
3 years parts and labor
Additional 2 years parts only
Batteries for AMP™ Rider
2 Years
Consumer
100% first year; prorated second year
HA
Exceptions and Limitations
The chart below details special exceptions to this warranty:
Warranty
Code
Warranty Exception
Warranty
Period
All
Batteries
1 Year
All
Belts, Muffler, Tires
None
All
Cloth, Plastic, and
Rubber Components
(Including Belts and
Cables)
All
Engines
Use
Detail
Consumer Prorated
Commercial These components are not covered
when used commercially.
Maximum
2 Years
All
Warranty is limited to 2 years for
consumer use. Except as noted above,
these components are covered for
defect, not for wear.
See Engine
Manufacturer’s
Warranty
All
Engines are covered by engine
manufacturer’s warranty. Refer to
engine manufacturer’s warranty
statement.
Consumer_2011
35
Customer Responsibilities
Register the product immediately at the time of sale. If the dealer does not register the product, the
customer must complete the product registration card in the literature package and return it to the Ariens
Company, or register the unit online at www.ariens.com, www.gravely.com, www.countax.com.
To obtain warranty service, the original purchaser must:
• Perform the maintenance and adjustments explained in the owner's manual.
• Promptly notify Ariens or an authorized Ariens, Gravely or Countax service representative of the need for
warranty service.
• Transport the product to and from the place of warranty service at owner's expense.
• Have the warranty service performed by an authorized Ariens, Gravely or Countax service representative.
To Find an Authorized Service Representative:
In the U.S. and Canada:
Use the dealer locator on our websites:
www.ariens.com
•
www.gravely.com
Or contact us by mail or by phone:
In the U.S., Canada, Mexico, Caribbean, In Europe, Asia, Africa or
Central and South America:
the Middle East:
Ariens Company
655 W. Ryan Street
Brillion, WI 54110
Phone: (920) 756 - 4688
www.ariens.com
Countax Ltd, Countax House
Great Haseley, Oxfordshire,
OX44 7PF
Phone: 0800 597 7777
www.countax.com
In Australia or New Zealand:
109-111 Abbot House
Hallam, Victoria 3803 Australia
Phone: (03) 9796 4244
1800 335 489
www.bynorm.com.au
Exclusions - Items Not Covered by This Warranty
• Parts that are not genuine Ariens, Gravely or Countax service parts are not covered by this warranty and
may void the warranty.
• Damages resulting from the installation or use of any part, accessory, or attachment which is not approved
by the Ariens Company for use with product(s) identified herein are not covered by this warranty.
• The following maintenance, service and replacement items are not covered by this warranty unless they
are noted in the Limitations section above: lubricants, spark plugs, oil, oil filters, air filters, fuel filters,
brake linings, brake arms, brake shoes, skid shoes, scraper blades, shear bolts, mower blades, mower
vanes, brushes, headlights, light bulbs, knives, cutters.
• Any misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires
repair is not covered by this warranty.
• Use of gasoline blends exceeding 10% ethanol voids any and all warranties.
• Products are designed to the specifications in the area that the product was originally distributed. Different areas may have significantly different legal and design requirements. This warranty is limited to the
requirements in the area in which the unit was originally distributed. Ariens Company does not warrant
this product to the requirements of any other area. Warranty service is limited to service within the area
originally distributed.
• In countries other than the United States and Canada, contact the Ariens Company dealer for warranty
policies that govern within your country. Rights may vary from country to country and within any one
country.
Disclaimer
Ariens Company may from time to time change the design of its products. Nothing contained in this warranty
shall be construed as obligating the Ariens Company to incorporate such design changes into previously
manufactured products, nor shall such changes be construed as an admission that previous designs were
defective.
LIMITATION OF REMEDY AND DAMAGES
Ariens Company's liability under this warranty, and under any implied warranty that may exist, is limited to
repair of any defect in workmanship, and repair or replacement of any defective part. Ariens Company shall
not be liable for incidental, special, or consequential damages (including lost profits). Some states do not
allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
DISCLAIMER OF FURTHER WARRANTY
Ariens Company makes no warranty, express or implied, other than what is expressly made in this
warranty. If the law of your state provides that an implied warranty of merchantability, or an implied
warranty of fitness for particular purpose, or any other implied warranty, applies to Ariens Company,
then any such implied warranty is limited to the duration of this warranty. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from region to region.
Consumer_2011
36
CALIFORNIA AND EPA (UNITED STATES ENVIRONMENTAL
PROTECTION AGENCY) EVAPORATIVE EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The CARB (California Air Resources Board), the EPA, and Ariens Company are pleased to explain the
evaporative emission control system's warranty on your 2011 model year small off-road equipment. In
California, new equipment that uses small off-road engines must be designed, built, and equipped to
meet the State's stringent anti-smog standards. Ariens Company must warrant the evaporative
emission control system on your small off-road equipment for the period listed below provided there
has been no abuse, neglect or improper maintenance of your equipment.
Your evaporative emission control system may include parts such as: fuel tanks, fuel lines, fuel caps,
valves, canisters, filters, vapor hoses, clamps, connectors, and other associated components.
MANUFACTURER'S WARRANTY COVERAGE:
This evaporative emission control system is warranted for two years. If any evaporative
emission-related part on your equipment is defective, the part will be repaired or replaced by Ariens
Company.
OWNER'S WARRANTY RESPONSIBILITIES:
• As the small off-road equipment owner, you are responsible for the performance of the required
maintenance listed in your Owner's Manual. Ariens Company recommends that you retain all
receipts covering maintenance on your small off-road equipment, but Ariens Company cannot deny
warranty solely for the lack of receipts.
• As the small off-road equipment owner, you should however be aware that the Ariens Company may
deny you warranty coverage if your evaporative emission control system part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
• You are responsible for presenting your small off-road equipment to an authorized Ariens, Gravely,
or Parker service representative as soon as the problem exists. The warranty repairs should be
completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding
your warranty coverage, you should contact Ariens Company Technical Service Center at
1-920-756-4688.
DEFECTS WARRANTY REQUIREMENTS:
(a.) The warranty period begins on the date the small off-road equipment is delivered to an ultimate
purchaser.
(b.) General Evaporative Emissions Warranty Coverage. Ariens Company warrants to the ultimate
purchaser and any subsequent owner that the evaporative emission control system when
installed was:
(1.) Designed, built, and equipped so as to conform with all applicable EPA and CARB
regulations; and
(2.) Free from defects in materials and workmanship that causes the failure of a warranted part
for a period of two years.
(c.) The warranty on evaporative emissions-related parts will be interpreted as follows:
(1.) Any warranted part that is not scheduled for replacement as required maintenance in the
written instructions must be warranted for the warranty period defined in subsection (b)(2).
If any such part fails during the period of warranty coverage, it must be repaired or replaced
by the Ariens Company. Any such part repaired or replaced under the warranty must be
warranted for a time not less than the remaining warranty period.
(2.) Any warranted part that is scheduled only for regular inspection in the written instructions
must be warranted for the warranty period defined in subsection (b)(2). A statement in such
written instructions to the effect of "repair or replace as necessary" will not reduce the
period of warranty coverage. Any such part repaired or replaced under warranty must be
warranted for a time not less than the remaining warranty period.
(3.) Any warranted part that is scheduled for replacement as required maintenance in the
written instructions must be warranted for the period of time prior to the first scheduled
replacement point for that part. If the part fails prior to the first scheduled replacement, the
part must be repaired or replaced by the Ariens Company. Any such part repaired or
replaced under warranty must be warranted for a time not less than the remainder of the
period prior to the first scheduled replacement point for the part.
CARB_EPA_2011
37
(4.)
(5.)
(6.)
(7.)
(8.)
(9.)
Repair or replacement of any warranted part under the warranty provisions of this article
must be performed at no charge to the owner at an authorized Ariens, Gravely, or Parker
service representative.
Notwithstanding the provisions of subsection (4) above, warranty services or repairs must
be provided at authorized Ariens, Gravely, or Parker service representatives that are
franchised to service the subject small off-road equipment.
The owner must not be charged for diagnostic labor that leads to the determination that a
warranted part is in fact defective, provided that such diagnostic work is performed at an
authorized Ariens, Gravely, or Parker service representative.
Throughout the evaporative emission control system's warranty period set out in subsection
(b)(2), the Ariens Company must maintain a supply of warranted parts sufficient to meet the
expected demand for such parts.
Manufacturer-approved replacement parts must be used in the performance of any
warranty maintenance or repairs and must be provided without charge to the owner. Such
use will not reduce the warranty obligations of the manufacturer issuing the warranty.
The use of any add-on or modified parts will be grounds for disallowing a warranty claim
made in accordance with this article. The manufacturer issuing the warranty will not be
liable under this Article to warrant failures of warranted parts caused by the use of an
add-on or modified part.
Evaporative Emission Warranty Parts List
The following parts are considered emission-related components for evaporative emissions:
• Fuel Tank, Fuel Cap and Tether
• Fuel Line, Fuel Line Fittings, Clamps*
• Pressure Relief Valves, Control Valves*
• Control Solenoids*, Electronic Controls*
• Vacuum Control Diaphragms*
• Control Cables*, Control Linkages*
• Purge Valves
• Vapor Hoses, Liquid/Vapor Separator
• Carbon Canister, Canister Mounting Brackets
• Carburetor Purge Port Connector
* As related to the evaporative emission control system
Disclaimer
New equipment sold in the state of California that uses small off-road engines must be exclusively
certified and appropriately labeled for sale in California. Some equipment covered by this Owner's
Manual my not be certified for sale in California and the presence of the preceding CARB and EPA
Warranty Statement does not by its existence indicate which, if any, of the equipment covered by this
Owner's Manual may be sold in California.
Some equipment covered by this Owner's Manual may have been manufactured prior to certain
affectivity dates requiring the inclusion of evaporative emission control systems. Therefore some
equipment covered by this Owner's Manual may not include the evaporative emission control systems
referred to in the preceding CARB and EPA Warranty Statement.
CARB_EPA_2011
38
GRAVELY
655 West Ryan Street
Brillion, WI 54110
920-756-4688
Fax 920-756-2407
www.gravely.com
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.