Craftsman 113.177920 Owner`s manual

Save This Manual
For Future Reference
SEARS
owner's
manual
MODEL NO.
113.177920
£RRFTSMRN®
i Serial
Number
Model and serial
numbers may be found
on the handle. You
i should record both
model and serial
' numbers in a safe place
for future use.
FOR YOUR
SAFETY
16 GALLON
FULL BLOWING
WET/DRY VAC
• assembly
• operating
• repair parts
READ ALL
INSTRUCTIONS
CAREFULLY
Sears,
Part No. SP6436
Roebuck
and Co., Hoffman
Estates,
IL. 60179
U.S.A.
Printed
in U.S.A.
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
WET/DRY VACS
If within one year from the date of purchase, this Craftsman Wet/Dry Vac fails
due to a defect in material or workmanship,
Sears will repair it, free of charge.
If this Craftsman
this warranty
Warranty
Wet/Dry
coverage
Service
Is Available
vice Center/department
This warranty
applies
This warranty
gives
rights
Vac is used for commercial
applies
By Simply
Throughout
Contacting
The United
on!y while this product
you specific
which
vary from
Sears,
Roebuck
or rental
for only 90 days from
legal
purposes,
date of purchase.
The Nearest
Ser-
States.
is used in the United
rights,
Sears
States.
and you may also have other
state to state.
and Co., D817 WA, Hoffman
Estates,
IL. 60179
IMPORTANT SAFETY INSTRUCTIONS
Safety
is a combination
sense,
staying
of common
alert and knowing
your vac works. Read
understand
the vac.
liquids,
how
this manual
to
means
is not followed
injured
cleaners,
or other
will be seriously
or killed.
Do not vacuum
Do not vacuum
seriously
tured
CAUTION:
or killed.
means
if the safety
tion is not followed
someone
informa-
may
be
injured.
When
using your Wet/Dry
safety precautions
Vac, follow basic
including
the following.
WARNING-To
the risk of fire, electric
dusts,
such
lighter
fluid
paints,
natural
shock,
or
injury:
anything
that is burning
fireplace
matches,
and all labels
soot or ash. This
by the filter and may cause damage.
To reduce
the risk of health
hazards
vapors or dusts, do not vacuum
materials.
Do not use or store near hazardous
To reduce
the risk of electric
to rain. Store
Do not allow Wet/Dry
toy. Close attention
materials.
shock,
do
indoors.
Vac to be used as a
is necessary
when
this owner's
on the Wet/Dry
manual
Vac before
Do not use this Wet/Dry
ter or without
Vac with a torn fil-
the filter installed
except
when vacuuming
liquids as described
the operation section of this manual.
injury or damage
Sears Craftsman
Do not leave Wet/Dry
to Wet/Dry Vac, use only
recommended
accesso-
ries.
inside
vapors
the motor can ignite
or dust. To reduce
flam-
the risk
of fire or explosion:
•
from
toxic
operating.
Use only as described
in this
manual. To reduce the risk of personal
mable
or
used by or near children.
Read and understand
Sparks
or
is a very fine dust which will not be cap-
not expose
reduce
Vac as a sprayer.
smoking, such as cigarettes,
hot ashes.
WARNING:
means if the safety information is not followed someone
could be
injured
fuels,
oil- based
• Do not use Wet/Dry
if the safety information
someone
as gasoline
or explosive
gas, hydrogen,
coal dust, magnesium
dust, grain dust, or gun powder.
Safety Signal Words
DANGER:
gases,
Do not vacuum,
or use this Wet/Dry
Vac, near flammable
or combustible
Vac when
in
plugged
in. Unplug from outlet when not in use and
before servicing.
Turn off Wet/Dry Vac
before
unplugging.
WARNING:
or electric
unattended.
To reduce
shock,
the risk
of fire
do not run vac
To reduce the risk of injury from acciden- To reducethe risk of falls, use extra care
tal starting, unplug power cord before
when cleaning on stairs.
changing or cleaning filter.
This Wet/DryVac is double-insulated,
Do not unplug by pulling on cord. To
eliminatingthe need for a separate
unplug,grasp the plug, not the cord.
groundingsystem. Use only identical
replacementparts. Read the instructions
Do not use with damagedcord, plug or
for
Servicing Double-InsulatedWet/Dry
other parts. If your Wet/Dry Vac is not
Vacs beforeservicing.
working as it should, has missing parts,
has been dropped, damaged,left outObservethe followingwarningsthat
doors, or droppedinto water, return it to a appear on the motor housingof your Wet/
Sears Service Center.
Dry Vac.
Do not pull or carry by cord, use cord as
DOUBLEINSULATED-GROUNDING
NOTREQUIRED
handle, close a door on cord, or pull cord
h-_
WHEN SERVICING
USE ONLY
around sharp edges or corners. Do not
run Wet/Dry Vac over cord. Keepcord
IDENTICAL REPLACEMENT PARTS
awayfrom heated surfaces.
WARNING:
To reduce the risk of
Do not handleplug or the Wet/Dry Vac
electric shock - do not expose to
with wet hands.
rain - store indoors.
Do not put any object into ventilation
openings. Do not vacuum with any ventiWARNING: For your own safety, read
and understand owner's manual. Do
lation openings blocked;keepfree of dust,
lint, hair or anything that may reduce air
not pick up hot ashes, coals, toxic,
flow.
flammable or other hazardous mateKeep hair,loose clothing, fingers, and all
parts of body awayfrom openings and
moving parts.
rials. Do not use around explosive
liquids or vapors.
SAVE THESE INSTRUCTIONS
The operation
of any utility
can result in foreign
vac or blower
objects
being blown
into the eyes, which can result in severe
eye damage.
complying
package)
Always
wear safety
with ANSI Z87.1
before
Safety Goggles
retail stores.
To reduce
are available
the risk of
for extended
(shown
commencing
wear ear protectors
hours
hearing
when
or when
goggles
on
operation.
at Sears
damage,
using the vac
using
it in a
noisy area.
For dust operations,
wear dust mask.
Use only extension co.rds that are rated
for outdoor use. Extension cords in poor
condition or that are too small in wire size
can pose fire and shock hazards. When
using an extension cord, be sure it is in
good condition. Using any extension cord
will cause some loss of power. To keep
the loss to a minimum, use the following
table to choose the minimum wire size
extension cord.
Extens!on
Cord Length
0-50 Ft.
50-100 Ft.
Gauge
A.W.G.
14
12
Introduction
This Wet/Dry
Vac is intended
Owner's
for house-
hold use only.
Shocks
Are Common
areas or when the relative
air is low. To reduce
static shocks
Contents
Item
IMPORTANT NOTE
Please Read Caref'ully
Static
Manual
- In dry
humidity
the frequency
of the
of
in your home the best rem-
edy is to add moisture
console humidifier.
to the air with a
Page
Warranty Information
.............................
Safety Instructions
.................................
Introduction ............................................
2
2
4
Unpacking and Checking
Carton Contents .............................
4
Assembly ...............................................
Operation ...............................................
Maintenance
........................................
5
8
10
Repair
12
Parts ........................................
Unpacking and Checking Carton Contents m
Remove
entire contents
each item against
of carton.
the Carton
List. Notify your Sears
Store
if any parts are damaged
Carton
Key
A
B
Check
A
Contents
immediately
or missing.
Contents
List
Description
._.........................
Qty.
VacAssembly
.............................
1
Pos-I-Lock
Hose Assembly
......... 1
C
D
E
Utility Nozzle ...............................
Wet Nozzle ..................................
Car Nozzle ..................................
1
1
1
F
G*
H*
Hose Lock ...................................
Filter Nut .....................................
Filter Plate ...................................
1
1
1
J*
Filter (Red Stripe)
.......................
1
K*
L*
M
Filter Cage ..................................
Float ............................................
Extension Wands ........................
1
1
2
N
Male/Male
P
Q
R
Caster Foot For Storage .............
Caster .........................................
Owners Manual ...........................
Connector
..................
B
1
M
4
4
1
*These items may come preassembled.
If they are not present in the carton
check the vac power head to see if they
are preassembled.
4
Float/Cage
WARNING:
For your
never connect
outlet
Assembly
plug to power
until all assembly
complete
instructions.
read and
Do not operate
1. Place the power
down
away from the lid. To replace,
cage assembly
of vac
injury
hands,
other foreign
objects
ter opening
float.
Power
Assembly
the risk of
or damage
sure to keep
instructions.
Tabs
opening in the center of the lid with the
words "This Side Towards Lid" laying
face down over the hole.
personal
follow float/
Filter
Cage---_
into the drum.
To reduce
in the wrong
the tab out of the slot. Tilt the cage and lift
vac
2. Locate the float. Place the float over the
WARNING:
the float is placed
filter cage and the center ring of the lid. Pry
or missing.
assembly
If filter cage needs to be removed,
way, use a flat blade screwdriver
and insert
the blade near one of the tabs between the
are
the safety and operation
with any parts damaged
upside
because
source
steps
and you have
understood
NOTE:
own safety,
to vac be
fingers,
or any
out of the cen-
when assembling
the
3. Line up filter cage tabs with the slots
the center ring of the lid.
in
4. Push on the filter cage until the tabs
snap into the slots for a secure
(3)
fit.
Slots (3)
Filter Assembly
1. Carefully
slide the filter over the filter
I_;_"'-----Filter
• cage, sliding it over the center ring covering the 3 slots until the filter stops
against
_)"'--Filter
Nut
Plate
the lid.
2. Place the hole in the filter plate over
threaded
screw
Filter
of the filter cage.
"_-Red
Stripe
3. Gently push on the filter plate to seat
the rubber ring of the filter inside the circular channel
of the filter plate.
4. Place filter nut onto threaded
tighten
NOTE:
from
it down.
Lever
Finger
of filter
screw
tighten
and
Filter Cage
only.
nut should
be away
plate as shown•
IMPORTANT:
may deform
Do not overtighten
as this
or crack the filter plate or filter
cage.
NOTE:
matches
Your filter has a red stripe that
an in-store
displayer.
When
visit your local Sears store, just remember
you
the
color of your stripe for the correct size filter.
5
Caster/Caster
Foot Assembly
1. Remove the power assembly
dust drum and set aside.
2. Turn the dust drum
floor.
3. Insert
the caster
upside
drum, as shown
Caster
U_.
Caster
Stem
-_ Caster
Ball
foot until the foot is
of the dust drum.
5. Insert the caster
upright.
__,.i
of
(4 places).
flush with bottom
7. Turn the drum
down on the
feet into the bottom
4. Push on the caster
the caster
from the
stem
into the socket of
foot, as shown
Caster--=Foot
Pin
(4 places).
6. Push on the caster until the ball on the
caster
stem is inserted
all the way into
the socket. You will hear the ball snap
into the socket and the caster will swivel
easily when
positioning
Hole
Dust Drum
is correct.
Vac Assembly
1. Line up vacuum
port in power
with drain cap located
the drum.
2. Place power
on the front of
3. Be sure power
4. Push down on top of the handles
cause the flexible
on top of drum
snug against
the drum
5. Make sure that the locking
snapped
assembly
assembly
completely
tabs are
in place to prevent
from coming
the power
off. (See inset
below)
covers the top of the drum so leakage
does not occur.
Push
Down
Vacuum Port
4
Pull
Out
Flexible _ I_
Locking
Tab
Drum
Channel
Lid
Handle
X
Drain
Do Not Force Flexible
Tab Beyond Stop Tab
Sto
Tab
to
locking tabs to hook
onto the drum lip of the channel.
assembly
with the handles
channel.
assembly
Out
Flexible Locking Tabs
6
6. Insert the push button end of the "Pos-ILock" hose into the inlet of the vac. The
hose should
snap into place. To remove
button in the hose assembly and pull the
hose out of the vac inlet, as shown.
the utility
opposite
ready
nozzle
securely
forcing
end of the hose and the vac is
together
a 9-16917
connec-
connector
end of the hose connected
the other
hose by
until they fit
- OR hose-hose
tor. Install the hose-hose
connect
on the
end of the original
the sections
tightly.
Purchase
the hose from the vac, press the release
7. Place
into the swivel
on the
to the vac and
hose to the hose con-
nector.
Release
Button
for use.
NOTE: The opposite end of the hose is
removable
if more hoses need to be
Press and
Pull
cC>
attached for more length from the vac. To
remove the swivel portion of the hose,
grasp the hose swivel and firmly pull it out
of the flexible hose. Connect the soft end
of a second
hose
(accessory
#9-17820)
Cord Wrap
Switch
Blowing
Port
Lid _
Handle
Vacuum
Port
Release
Button
Swivel
End
Drum
!
Utility
Larger
Open!ng.
Power
Assembly
Hose
Drain
Open
Of Hose
Lock
To Store Your Accessories
1. Slide extension
handles
ries into the slotted
caster
and accesso-
areas
of the
feet for storagel
2. To remove
the accessories,
rotate
and
pull upward.
7
Operation
WARNING
To reduce
the risk of fire or explosion,
flammable
gases,
vapors
or explosive
do not operate
this vac in areas
dust in the air. Flammable
with
gases
or
vapors include but are not limited to; lighter fluid, solvent type cleaners, oilbase paints, gasoline,
alcohol or aerosol sprays. Explosive
dusts include but
are not limited to; coal, magnesium,
grain or gun powder. Do not vacuum
explosive
dust, flammable
or combustible
liquids
this vac as a sprayer. To reduce the risk of health
or hot ashes.
hazards from
Do not use
vapors or
dusts, do not vacuum toxic materials.
CAUTION:
damage
To reduce
wear
risk of hearing
ear protectors
NOTE: A dry filter is necessary
to pick up
dry material. If you use your vac to pick up
dust when the filter is wet, the filter will
when
using the vac for extended
hours or
when using it in a noisy area. The
clog quickly
operation
of any utility vac can
result in foreign
objects being
blown into the eyes, which can
result in severe eye damage. Always
the vac to pick up dry material, you can
quickly dry the filter by running the vac
without hose attached for about 10 minutes. The clean air rushing
vac will help dry the filter.
before commencing
operation.
Safety Goggles are available at
Sears retail stores.
the risk of electric
does
plug.
shock,
Vacuuming
the proper
Do not change
the plug in any way.
symbol
"ON".
for "OFF"
outlet.
removed.
O=OFF
Vacuuming
and misting
it
may
3. After using the vac to pick up liquids,
the filter must be dried to reduce the
risk of possible
the filter.
for
mildew
and damage
to
4. When the liquid in the drum reaches a
predetermined
level, the float mecha-
I =oN
nism will rise automatically
flow. When this happens,
Dry Materials
to cut off airturn off the
vac, unplug the power cord, and empty
the drum. You will know that the float
has risen because vac airflow ceases
1. The filter must always be in correct
position to reduce the risk of leaks and
possible damage to vac.
and the motor noise will become
in pitch, due to increased
2. When using your vac to pick up very
IMPORTANT:
fine dust, it will be necessary for you to
empty the drum and clean the filter at
more frequent
of liq-
If the filter is not removed,
will become saturated
appear in the exhaust.
"O" is the
and "l" is the symbol
amounts
2. When picking up large amounts of liquid we recommend
that the filter be
from position "O" to position "l". The symbols used on the motor cover are interna"On & Off" symbols.
up small
uid the filter may be left in place.
After you plug the power cord into the outlet, turn the unit on by pushing the switch
tional
Liquids
1. When picking
not fit fully in the outlet, reverse the
If it still does not fit, contact a qualito install
the
ter job stopping the very fine particles
than the 9-17816 filter.
this
outlet only one way. If the plug
fied electrician
through
The optional Craftsman
High Efficiency
Filter, stock number 9-17918 will do a bet-
appliance
has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized
to clean.
3. If your filter is wet but you need to use
wear safety goggles complying
with
ANSI Z87.1 (shown on Package)
To reduce
and be very difficult
To reduce
higher
motor speed.
the risk of dam-
age to the vac do not run motor with float
in raised position.
intervals to maintain
peak vac performance.
8
Emptying
Moving the Vac
the Drum
WARNING:
To reduce
injury
accidental
from
unplug power
the drum.
1. Should
the risk of
necessary
up by the lid handles
emptying
is empty. To reduce
unless
equipped
for easy emptying
unscrew
with a drain
of liquids•
Simply
the drain cap and lift the oppo-
site side slightly
2. Another
option
to empty
the drum.
is to remove
the power
assembly• Pull the flexible latches outward on each side of the lid to release
from
the drum.
3. While
holding
power
drum.
assembly
4. Lay power
clean
the latches
up and away from the
assembly
area while
upside
emptying
5. Dump the drum contents
waste disposal
WARNING:
out, lift the
down on a
drum.
enough
out to
to lift
Cord Wrap/Carry
Handle
The
a convenient
wrap
vac has
area/carry
handle
rear of the vac. Simply,
designed
wrap the
cord
on the
power
on the plug to a wrap of the cord
and the cord is wrapped
steps
below to use your vac as a blower.
WARNING: Always wear safety goggles complying with ANSI Z87.1
before using as a blower.
WARNING: To reduce the risk of
injury to bystanders, keep them
clear of blowing debris.
for storage.
blowing
per4 of your vac.
insert
the opposite
male adapter
the vac.
end of the male/
into the blowing
Attach
extension
port of
wand to
opposite end of hose, then place
blower nozzle on the wand.
cord around the handle and snap the connector
Your vac features "Full Blowing".
It can
blow sawdust and other debris. Follow the
3. (Optional)
comfortably.
wet/dry
Blowing Feature
2. Insert the male/male adapter into the
locking tab adapter end of the hose.
risk of
contents
make the vac light
or pos-
sible part breakage,
pick the vac up by
the lip of the dust drum.
1. Locate
container.
To reducethe
enough
releasing
into the proper
back injury or falls, do not lift a vac
heavy with liquid or debris. Scoop
or drain
dust drum
the risk of dropping
the vac due to latches
•The vac comes
to pick the
vac up to move it, DO NOT pick the vac
starting,
cord before
it become
4. Turn vac on and you are ready
a
to use
your vac as a blower.
Sears
recommended
available
Blower
at Sears
Nozzle
extension
Stock
handles
recommended
accessories
retail stores.
are
The Sears
No. 9-16933
and
Stock No. 9-16964
for blowing
are
debris.
Male/Male
g Hose End
Swivel End
of Hose
Extension
Wand
(Optional)
(Optional)
Maintenance
Filter
IMPORTANT:
WARNING:
To reduce
unplug
power
or cleaning
age to the blower
the risk of
injury from accidental
changing
Dry
filter.
This filter is made
of high quality
performance
Cleaning
maintain
be cleaned
often to
storing
hole can cause
results
your vac. Replace
Cleaning
SHOULD
doors
and not in the living
by gently
replacement,
unsc_ew
WARNING:
remove
fingers
wheel.
from
Wet Filter
strong
or
filter plate and lift
the filter
to help prevent
getting
of dry filter with
fine dust (no debris), run water through
it as described
under "Wet Filter".
run water through
enough
your
into the blower
Take care
from the hose is not
to damage
filter. Remem-
ber: To dry a filter quickly, reinstall the filter on the vac and allow the unit to run for
approximately
It is there
the filter
the filter from a hose or spigot.
the filter nut from
Do not remove
tapping
cleaning
that water pressure
the filter cage,
off filter.
quarters.
from vac, re[hove the
After filter is removed,
it immediately.
the filter for cleaning
be done out-
out of
Removal
To remove
the fil-
due to accu-
area.
4. For thorough
a lot of dust to come
can be
removing
against the inside wall of your dust
drum. The debris will loosen and fall.
or
up dry debris.
using the
dust, clean the filter in an open
dry debris
peak vac performance.
IMPORTANT:
After cleaning, check the
filter for tears or small holes. Do not use a
filter with holes or tears in it. Even a small
cage.
mulated
3. After filter removal
Be sure to dry the filter before
picking
of dry debris
without
2. For best cleaning
of the filter.
Your filter should
and motor,
ter from the vac. Slap your hand on top
of the power assembly while the vac is
turned off.
the filter carefully
when removing to clean or installing it.
Creases in the filter pleats may occur from
installation
but creases will not affect the
removal
accomplished
paper designed to stop very small particles of dust. The filter can be used for wet
or dry pick up. Handle
wheel
Filter
1. Some
NOTE:
the risk of dam-
always reinstall the filter before
vac for dry material pickup.
starting,
cord before
To reduce
rushing
10 minutes.
through
The clean
air
the filter will dry it.
Installation
Refer to page 5, "Filter
Assembly".
Allow the filter to dry before
storing
the
vac.
Wet/Dry Vac
To keep your Wet/Dry
Vac looking its best,
WARNING:
To assure
clean the outside with a cloth dampened
SAFETY
with warm
and adjustmentshould
water and mild soap.
To clean the drum:
1. Dump debris
out.
2. Wash drum thoroughly
and mild soap.
3. Wipe
out with dry cloth.
with warm
product
and RELIABILITY,
formed
by Sears
always
using
Service
Sears
repairs
be perCenters,
replacement
parts.
water
NOTE: If your casters are noisy, you may
put a drop of oil on the roller shaft to make
them quieter.
10
2. Using
Wet Nozzle
to you. With fingers on the far side and
thumbs holding the latches of the
vac. To use this
nozzle, simply attach the nozzle to the
end of an extension wand.
Connect a second extension wand to the
first, and connect the 2-1/2"
the extension wand.
lower the nozzle
body onto the insert and squeegee
with
the round opening of the nozzle closest
To pick up liquids off a smooth surface,
use the 2-1/2" wet nozzle accessory
supplied with your wet/dry
both hands,
removable
insert,
the latches
are on the top and the round
inlet opening
x 7' hose to
flip the nozzle
is facing away from you.
Make sure the squeegee
insert
Liquids may be picked up by dragging the
nozzle across the surface. The squeegee
over so
stays on the
pins.
will dry the surface as you vacuum.
Replacement
rubber for the squeegee
nozzle may be obtained through Sears
Parts. If the rubber becomes worn, it may
be flipped
over for use on the opposite
side or replaced.
part #822256).
(Replacement
To reverse
service
or replace
the
3. Press down with each thumb
squeegee:
latching
1. Lay the wet nozzle on a flat surface with
the round inlet opening facing up and
the two latches
below the
tabs until you see and hear the
removable
insert snap
into the nozzle
body. Snap the latche# over the locking
tabs into their original position.
close to you as shown.
Latches
Nozzle
Body
Removable
Insert
4. Inspect
2. Using both hands, position each thumb
on the removable insert, (below the
latches)
and two fingers
squeegee
of each hand
NOTE:
To reinstall
follow
the removable
slots
body.
If the pins are out of position,
hold the nozzle
assembly
with both
hands and gently twist in opposite
directions.
The insert pins should snap
body.
toward
the holes of the
and fit into the matching
in the nozzle
on each latch, lift and disengage
the
two latches from the tabs on the nozzle
3. Gently pull the latches
to remove the insert.
the pins of the insert to make
sure they fit through
yourself
into proper
Twist
Backward
insert correctly,
position.
Twist
Forward
these steps:
1. Place the removable
insert on a flat sur-
face with the pins positioned
upward
and the latches close to you as shown.
Place
the rubber
squeegee
on the
insert, with the pins fitting through the
matching holes in the squeegee.
(Make
sure the new working
farthest
_.._
._ •
edge
is located
-
.
The wet nozzle
pickup
from you.)
:
-
._ -
.
-
"_ :
11
use.
assembly
is ready
for wet
Repair Parts
16 Gallon Wet/Dry Vac
Model Number 113.177920
Always
order
by Part Number-
Not by Key Number
WARNING
SERVICING
OF DOUBLE-INSULATED
In a double-insulated
Wet/Dry
instead of grounding.
appliance,
nor should
insulated
should
Wet/Dry
be done
Vac, two systems
extreme
only by qualified
care and knowledge
service
double-insulated
Wet/Dry
Vac must
double-insulated
Wet/Dry
Vac is marked
and the symbol
ance.
[--_(square
within
personnel.
be identical
a square)
of the system,
Replacement
"DOUBLE
may also be marked
and
parts for a
Your
INSULATED"
on the appli-
Description
1
73180
2
824941
Toggle Switch
Motor Cover
3
822467-5
Cord w/plug
4
824967
5
STD611007
6
818793
7
818961
8
818413-2
Spacer
Blower Wheel
9
15534-1
Washer
10
73352
11
823690-4
Nut, Hex Flange
Lid
12
509238
Float/Filter
13
9-17816
1- Filter (Red Stripe)
14
9-16937
1 Filter Plate
15
9-16938
16
809544-3
t Filter Nut
Dust Drum
17
73185
18
9-16990
19
73102
t Caster Foot w/Storage
Casters
20
9-17822
t Hose 2-1/2"
21
9-17823
t Adapter
22
821421-10
Ring "O"
23
815096
Adapter
24
826355-1
25
826354
Spring Tab
End Hose Interlock
822256
Squeegee
SP6436
Owners
Hardware
are provided
to the parts they replace.
with the words
Part No.
1 Stock Item - May Be Secured
Stores
* Standard
of insulation
VAC
No grounding
means is provided on a double-insulated
a means for grounding
be added. Servicing
a double-
Vac requires
Key
No.
WET/DRY
Motor (Includes
Key No's 7,thru
10)
* Screw, Pan Hd. Ty "AB" 10x3/4
Lid Gasket
Drain
Through
1/4-20
Cage
Cap
x 7'
Hoselock
Hose
(Not Illustrated)
Manual
The Hardware
Item - May Be Purchased
12
Locally.
(Not illustrated)
Department
Of Most Sears
Retail
Repair Parts
16 Gallon Wet/Dry Vac
Model Number 113.177920
J
2
J
4
22
21
2O
23
J
L
J
25
13
£RRFTSMRN®
Accessories
Get more versatility
ries.
Additional
wet/dry
or Sears/Craftsman
17820
2-1/2"x7'
16922
Utility
16978
and Attachments
from your Craftsman
vac accessories
Power
wet/dry
vacuum
may be purchased
by adding
these accesso-
at your local Sears
retail store
and Hand Tool Catalog.
Hose
Nozzle
CarJ_lozzle
16926 14" Floor
Brush
17822
Pos-I-Lock
17817
16933
Hose
Wet Nozzle
Blower
Nozzle
16947, 16948
Inflator Nozzle
16964 Extension
16925
16902
Wands
Dry Nozzle
Crevice
Tool
16901 Dusting
Brush
m===_li=_.==pm=
16931/16990 Caster
Feet for Storage
NOTE:
Most Accessories
17816 Paper Pleated
Filter
Are Available
14
In 2-1/2
16939
Drum
& 16940
Liners
Inch And 1-1/4 Inch Sizes
16934 Hose Grip
16917 Hose Joiner
16930 Hose Lock
16935Gutter Nozzle
Sawdust Collection Series
Whole-shop
Sawdust Manifold-Type
Collection
System
29964
Table Saw Dust
Collection Kit
29962
Radial Arm Saw
Dust Collection Kit
29963
15
For in-home
major brand
repair service:
Call 24 hours a day, 7 days a week
1-800-4-MY-HOME
(1-800-469-4663)
Para pedir servicio de reparacibn
a domicilio - 1-800-676-5811
For the repair or replacement
parts you need:
Call 6 am - 11 pm CST, 7 days a week
PartsDirect
1-800-366-PART
Para ordenar
piezas
(1-800-366-7278)
con entrega
a domicilio
- 1-800-659-7084
For the location of a Sears Parts and Repair Center
in your area:
Call 24 hours a day, 7 days a week
1-800-488-1222
For information
on purchasing
a Sears Maintenance
Agreement
or to inquire about an existing Agreement:
Call 9 am - 5 pm, Monday - Saturday
1-800-827-6655
SEARS
HomeCentral
SM
The model and serial numbers will be found on the handle.
When requesting service
following information:
•
•
or ordering
Product Type
Part Number
•
•
parts, always provide the
Model Number
Part Description
Sears, Roebuck and Co., Chicago, IL 60179 U.S.A.
© 2001 Emerson Electric Co.
Part No. SP6436
Form
No. SP6436
Printed
in U.S.A.
4/01