Samsung SyncMaster 795MB Specifications

SyncMaster 591S/793S/591V/793V/783DF/793DF
/795DF/797DF/997DF/793MB/795MB
Downloaded from ManualMonitor.com Manuals
Main Page
On-Screen Display
Safety Instructions
Troubleshooting
Notational
Check List
Power
Q&A
Installation
Self-Test Feature Check
Clean
Other
Introduction
Specifications
Unpacking
General Specifications
Front
PowerSaver
Rear
Preset Timing Modes
Bottom
Setup
Information
Connecting Your Monitor
Service
Installing the Monitor Driver
Terms
Automatic
Regulatory
Manual
Natural Color
Base Installation
Downloaded from ManualMonitor.com Manuals
Authority
Notational
Power
Installation
Clean
Others
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
Downloaded from ManualMonitor.com Manuals
When not used for extended periods of time, set your computer to DPMS. If
using a screen saver, set it to the active screen mode.
z
Notational
Power
If the size of your monitor is small, or if the same image is present for long
periods of time, you may see afterimages due to damage to the
fluorescent substance on the inside of the CDT.
Installation
Clean
Do not use a damaged or loose plug.
Others
z
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet
hands.
z
This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
z
An improper ground may cause electric shock or equipment
damage.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
z
This may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or
if it is not used for a long period of time.
z
This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
z
Downloaded from ManualMonitor.com Manuals
This may cause fire.
Do not cover the vents on the monitor cabinet.
z
Bad ventilation may cause a breakdown or fire.
Notational
Power
Installation
Clean
Others
Put your monitor in a location with low humidity and a minimum of
dust.
z
An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
z
This may cause damage to the product or human body.
Place the monitor on a flat and stable surface.
z
The monitor may cause injury by falling.
Set down the monitor carefully.
z
It could be damaged or broken.
Do not place the monitor face down.
z
The CDT surface may be damaged.
Do not use the monitor without the monitor stand.
z
z
Downloaded from ManualMonitor.com Manuals
It could break down or cause a fire due to bad ventilation.
If the monitor must be used without the supplied stand, take steps
to insure proper ventilation.
Notational
Power
Installation
Clean
Others
When cleaning the monitor case or the surface of the CDT, wipe with a
slightly moistened, soft fabric.
Do not clean Flat monitor with water. Use a water-diluted mild
detergent.
(Some detergents contain significant amounts of alcohol-based solvents,
which can damage (color change) or crack the monitor case. The
antiglare/anti-static surface coating on the CDT may also be affected.)
Dilute the detergent (1:10 ratio) with water before using.
Do not water or spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
z
z
You can prevent the coated CDT from being damaged or the
monitor cabinet from being dissolved, cracked or discolored.
You can buy a recommended detergent at any Samsung Service
Center.
If the connector between the plug and the pin is dusty or dirty,
clean it properly with a dry cloth.
z
A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects
on the monitor.
z
z
Downloaded from ManualMonitor.com Manuals
This may cause damage, electric shock or a fire.
If a foreign substance gets into the monitor, disconnect the plug
and then contact a service center.
Do not remove cover(or back).
z
z
This may cause an electric shock or fire.
Refer servicing to qualified service personnel.
Notational
Power
Installation
Clean
Others
If your monitor does not operate normally - in particular, if there are
any unusual sounds or smells coming from it - unplug it
immediately and contact an authorized dealer or service.
z
This may cause an electric shock or fire.
Do not place any heavy objects on the monitor.
z
This may cause an electric shock or fire.
For each hour of looking at the monitor, you should let your eyes
rest for 5 minutes.
z
This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
z
This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal
cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Never insert anything metallic into the monitor openings.
z
This may cause an electric shock, fire or injury.
Keep the monitor away from any magnetic substances.
z
Downloaded from ManualMonitor.com Manuals
This may cause discoloring or distortion of the image.
SyncMster 591S / 793S / 591V / 793V / 793DF / 795DF /
797DF / 997DF / 793MB / 795MB
Monitor and Stand
Power Cord
Unpacking
Front
Stand
Rear
Bottom
Quick Setup Guide
(Some models include a stand attached. )
Please make sure the following items are included
with your monitor. If any items are missing,
contact your dealer.
Warranty Card
(Not available in all locations)
User's Guide, Monitor Driver
SyncMaster 783DF
For Multimedia model (Option)
Multimedia Speaker Stand
Sound Cables(2each)
DC Power Cord
User Guide
Downloaded from ManualMonitor.com Manuals
SyncMster 591S / 793S / 591V / 793V / 793DF / 795DF /
797DF / 997DF / 793MB / 795MB
Unpacking
Front
Rear
Bottom
1. Menu button
2. Adjust buttons
3. Enter button
4. Power button
5. Power indicator
Opens the OSD menu. Also used to exit the OSD menu or return to the
previous menu.
These buttons allow you to highlight and adjust items in the menu.
Used to select the OSD menu.
Use this button for turn the monitor on and off.
This light glows green during normal operation, and blinks green once as
the monitor saves your adjustments.
Note: See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when
leaving it unattended for long periods.
SyncMaster 783DF
Downloaded from ManualMonitor.com Manuals
General
SyncMaster 591S/793S/591V/793V/783DF/795DF
793DF/797DF/997DF/793MB/795MB
Unpacking
Front
Rear
Bottom
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
2. Signal Cable
Connect the power cord for your monitor to the power port on the back of
the monitor.
Connect the signal cable to the video port on your computer, video board,
video card, or graphics card.
SyncMaster 997DF
BNC Connectors (Option)
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
2. Signal port
3. BNC Connectors
(Option)
Connect the power cord for your monitor to the power port on the back of
the monitor.
Connect the signal cable to the 15-pin D-sub connector on the back of
your monitor.
Connect the signal cable to the BNC signal port on the back of your
monitor.
Note: See Connecting the Monitor for further information regarding cable connections.
Downloaded from ManualMonitor.com Manuals
Unpacking
Front
Rear
Bottom
1. Signal Cable
2. Power port
3. Tilt/Swivel Base
Downloaded from ManualMonitor.com Manuals
Connect the signal cable to the video port on your computer, video board,
video card, or graphics card.
Connect the power cord for your monitor to the power port on the back of
the monitor.
You can separate the base from the monitor.
SyncMaster 591S/793S/591V/793V/783DF/795DF
793DF/797DF/997DF/793MB/795MB
Ge nera l
BNC C onne cto rs (Option)
Connecting the
Monitor
General
Installing the
Monitor Driver
Base Installat ion
1.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2-1.
Connecting to a computer
Connect the signal cable to the 15 -pin, D-sub connector on the back of your monitor.
2-2.
Connecting to a new Macintosh
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
2-3.
Connecting to an old Macintosh
Connect your monitor to the Macintosh using the adapter for Macintosh (sold separately).
3.
Turn on your computer and monitor. If your monitor displays an image, installation is
complete.
BNC Connec tors (Option)
Downloaded from ManualMonitor.com Manuals
SyncMaster 997DF
1.
2-1.
2-2.
2-3.
3.
4.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Connecting to a computer
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
Connecting to a new Macintosh
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
Connecting to an old Macintosh
Connect your monitor to the Macintosh using the adapter for Macintosh (sold separately).
When you use a BNC connector.
Connect the signal cable to the BNC signal port on the back of your monitor/computer.
Turn on your computer and monitor. If your monitor displays an image, installation is
complete.
Setup-For Multimedia model
Downloaded from ManualMonitor.com Manuals
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Turn off your computer and unplug the power cord.
Connect the end of the signal cable to your computer's video port(video board, vide o card or
graphics card).
Connect one end of the other sound cable to the Mic Input jack on your sound card or
computer.Connect the other end of this cable to the Mic By-pass jack on the back of the
monitor stand.
Plug the DC power cord from the stand into a nearby outlet.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor and the power cord for your computer into a nearby outlet.
Turn on your computer and monitor.
Turn up or down the On-Off control terminal on the stand of the monitor until it clicks.
Execute a sound program, music or sound effect in your computer and then adjust the volume
by turning up or down until the sound volume is appropriate.
Adjust the treble and bass.
Sound distortion may occur when the monitor is placed on top of a mostly hollow cabinet such
as your computer. If this occurs, place a pad or magazine beneath the monitor stand. High
sound volume may also cause sound distortion; lower the volume.
Multimedia Speaker Stand
1. Mic By-pass Jack
To transmit your voice,connect a sound cable from
the Mic By-pass jack to the mic in jack on the sound
card slot in your computer.
2. Stereo Input Jack
Connect a sound cable from the input source(sound
card,computer,CD-ROM drive).
3. DC Power Cord
Connect DC power cord to monitor DC 12V output
jack.
4. Power Indicator
Glows green when the speakers are turned on.
5. On/O ff Volume
Turns On/Off and adjusts the output volume.
6. Treble Control
Use to control high frequencies.
7. Bass Control
Use to control low frequencies.
8. Mic Input J ack
To transmit your voice,connect a microphone to this
jack.
9. Headphone Jack
To listen in privacy,connect headphones here.
10. Detachable Stand Top
Downloaded from ManualMonitor.com Manuals
Connecting the
Monitor
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Installing the
Monitor Driver
Base Installation
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/ (WorldWide)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Windows ME
1. Insert CD into the CD-ROM drive.
2. Click "Windows ME Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.
Windows XP/2000
1. Insert CD into the CD-ROM driver.
2. Click "Windows XP/2000 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
Downloaded from ManualMonitor.com Manuals
4. Click the "Install" button in the "Warning" window.
5. If you can see following "Message" window, then click the "Continue Anyway" button.
Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
6. Monitor driver installation is completed.
Downloaded from ManualMonitor.com Manuals
Connecting the
Monitor
Windows XP
Installing the
Monitor Driver
| Windows 2000 | Windows Me | Windows NT | Linux
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
Base Installation
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
Internet web site : http://www.samsung-monitor.com/ (WorldWide)
http://www.samsungusa.com/monitor/ (USA)
http://www.sec.co.kr/monitor/ (Korea)
http://www.samsungmonitor.com.cn/ (China)
Microsoft® Windows® XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Downloaded from ManualMonitor.com Manuals
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the
model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then
click "OK" button.
Downloaded from ManualMonitor.com Manuals
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung-monitor.com/.
9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Click "Start" , "Setting" , "Control Panel".
Double click the "Display" Icon.
Choose the "Settings" tab and then click "Advanced..".
Choose "Monitor".
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
Choose "Display a list of the known drivers for this device so that I can choose a
specific driver" then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver).
Click the "Open" button, then click "OK" button.
Choose your monitor model and click the "Next" button then click "Next" button.
Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button.
And click the "Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
1.
2.
3.
4.
5.
6.
Click "Start" , "Setting" , "Control Panel".
Double click "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Select the "Monitor" tab.
Click the "Change" button in the "Monitor Type" area.
Choose "Specify the location of the driver".
Downloaded from ManualMonitor.com Manuals
7.
8.
9.
10.
Choose "Display a list of all the driver in a specific location.." then click "Next" button.
Click the "Have Disk" button
Specify A:\(D:\driver) then click "OK" button.
Select "Show all devices" and choose the monitor that corresponds to the one you
connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties
dialogue box.
(You can get some other screen for warning message or others, then click the appreciate
option for your monitor.)
Microsoft® Windows® NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display
Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note: If there is no Mode at All Display Modes, select the level of resolution and vertical
frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1.
2.
3.
4.
5.
6.
7.
Press Enter at the first and the second screen after executing the X86Config file.
The third screen is for setting your mouse.
Set a mouse for your computer.
The next screen is for selecting a keyboard.
Set a Keyboard for your computer.
The next screen is for setting your monitor.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency
directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual
execution of X-Window.
10. You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
Downloaded from ManualMonitor.com Manuals
Tilt/Swivel Base
Connecting Your
Monitor
Installing the
Monitor Driver
Base Installation
| Attaching and Removing the Base
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable
viewing angle.
Note: The base is detachable.
If your monitor was supplied with the base detached, attach the base as follows.
Remove the twist-tie before attaching the base to the monitor.
Downloaded from ManualMonitor.com Manuals
Attaching the Base
1.
2.
3.
4.
Place the monitor upside-down on a flat work surface.
Align the tabs on the base with the corresponding slots on the bottom of the monitor.
Press the base onto the monitor until the tabs are fully engaged in the slots.
Push the base toward the front of the monitor until the release latch clicks into the locked
position.
* Do not bend the snap.
Removing the Base
5. Squeeze and pull up on the release latch on the base.
6. Push the base toward the back of the monitor and lift up to remove the base.
Note: The base will align with the monitor slots in only one position.
Downloaded from ManualMonitor.com Manuals
SyncMaster 591S/591V
User con trol butt ons
Direct-Access Fe ature s
OSD Fu nction s
MagicTune ™
Adju sting Yo ur
Monitor
User co n tro l bu tto ns
1.
Op ens the OSD menu. Also use to exit t he OSD m enu or re turn to the p revious menu .
2.
These b uttons allow you t o highlig ht and a dju st item s in t he men u.
3.
Use to select the OSD menu .
Direct -Acces s Fe atu res
| Brightness |
| Contrast |
Downloaded from ManualMonitor.com Manuals
OSD Fu n ctio ns
osd
Descrip tion
Adju st t he Bright ness.
Adju st t he Co ntrast.
A "Mo iré" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts.
A "Mo irë" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the vertical moire a dju stm ents.
The Degau ss fea ture will remove color im purities caused by mag netic fie lds.
Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size ,
Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire.
Note: If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings
will remain the sam e.
Downloaded from ManualMonitor.com Manuals
Play / Stop
osd
Descrip tion
Play / Stop
Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. (6500K / 9 300K)
Use to ad just th e monitor color setting. (Re d)
Use to ad just th e monitor color setting. (Gre en)
Use to ad just th e monitor color setting. (Blue)
When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode
exits.
osd
Descrip tion
Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay.
Follow th ese in structions to chang e the vetical position of the m onitor's entire display.
Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display.
Follow th ese in structions to chang e the vertical size of the m onitor's entire display.
Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut.
Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or
right.
Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all.
Adju st t he parallelogram sett ing when the display is leaning left or rig ht.
Downloaded from ManualMonitor.com Manuals
Play / Stop
You can see th e fre quency (u ser control mode) used by th e user, the polarit y o f the op erationa l signals, the d efault
frequ ency (defa ult mode) set wh en you bu y t he mon itor and the resolu tio n le ve l.
Note : The se screens do n ot allo w any chan ges to the set ting s, they are for inf orma tio n only.
Downloaded from ManualMonitor.com Manuals
SyncMaster 793S/793V/783DF/793DF/795DF
User con trol butt ons
Direct-Access Fe ature s
OSD Fu nction s
MagicTune ™
Adju sting Yo ur
Monitor
User co n tro l bu tto ns
1.
Op ens the OSD menu. Also use to exit t he OSD m enu or re turn to the p revious menu .
2.
These b uttons allow you t o highlig ht and a dju st item s in t he men u.
3.
Use to select the OSD menu .
Direct -Acces s Fe atu res
| Brightness |
| Contrast |
Downloaded from ManualMonitor.com Manuals
OSD Fu n ctio ns
osd
Descrip tion
Adju st t he Bright ness.
Adju st t he Co ntrast.
A "Mo iré" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts.
A "Mo irë" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the vertical moire a dju stm ents.
The Degau ss fea ture will remove color im purities caused by mag netic fie lds.
Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size ,
Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire.
Note: If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings
will remain the sam e.
Downloaded from ManualMonitor.com Manuals
Play / Stop
osd
Descrip tion
Play / Stop
Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. (6500K / 9 300K)
Use to ad just th e monitor color setting. (Re d)
Use to ad just th e monitor color setting. (Gre en)
Use to ad just th e monitor color setting. (Blue)
When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode
exits.
osd
Descrip tion
Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay.
Follow th ese in structions to chang e the vetical position of the m onitor's entire display.
Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display.
Follow th ese in structions to chang e the vertical size of the m onitor's entire display.
Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut.
Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or
right.
Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all.
Adju st t he parallelogram sett ing when the display is leaning left or rig ht.
Adju st t he ro tation setting w hen th e entire display is tilted left or rig ht.
Downloaded from ManualMonitor.com Manuals
Play / Stop
You can see th e fre quency (u ser control mode) used by th e user, the polarit y o f the op erationa l signals, the d efault
frequ ency (defa ult mode) set wh en you bu y t he mon itor and the resolu tio n le ve l.
Note : The se screens do n ot allo w any chan ges to the set ting s, they are for inf orma tio n only.
SyncMaster 783DF
Downloaded from ManualMonitor.com Manuals
SyncMaster 797DF
User con trol butt ons
Direct-Access Fe ature s
OSD Fu nction s
MagicTune ™
Adju sting Yo ur
Monitor
User co n tro l bu tto ns
1.
Op ens the OSD menu. Also use to exit t he OSD m enu or re turn to the p revious menu .
2.
These b uttons allow you t o highlig ht and a dju st item s in t he men u.
3.
Use to select the OSD menu .
Direct -Acces s Fe atu res
| Brightness |
| Contrast |
Downloaded from ManualMonitor.com Manuals
OSD Fu n ctio ns
osd
Descrip tion
Adju st t he Bright ness.
Adju st t he Co ntrast.
A "Mo iré" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts.
A "Mo irë" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the vertical moire a dju stm ents.
The Degau ss fea ture will remove color im purities caused by mag netic fie lds.
Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size ,
Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire.
Note: If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings
will remain the sam e.
Downloaded from ManualMonitor.com Manuals
Play / Stop
osd
Descrip tion
Play / Stop
Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. T he availa ble ran ge
is betw een 5 000 to 9300K.
Use to ad just th e monitor color setting. (Re d)
Use to ad just th e monitor color setting. (Gre en)
Use to ad just th e monitor color setting. (Blue)
When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode
exits.
osd
Descrip tion
Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay.
Follow th ese in structions to chang e the vetical position of the m onitor's entire display.
Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display.
Follow th ese in structions to chang e the vertical size of th e monitor's entire disp la y.
Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut.
Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or
right.
Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all.
Adju st t he parallelogram sett ing when the display is leaning left or rig ht.
Adju st t he ro tation setting w hen th e entire display is tilted left or rig ht.
Downloaded from ManualMonitor.com Manuals
Play / Stop
Adju st t he sid e pin corne r correction w hen th e top or bott om of th e displa y is too large or
sma ll.
You can see th e fre quency (u ser control mode) used by th e user, the polarit y o f the op erationa l signals, the d efault
frequ ency (defa ult mode) set wh en you bu y t he mon itor and the resolu tio n le ve l.
Note : The se screens do n ot allo w any chan ges to the set ting s, they are for inf orma tio n only.
Downloaded from ManualMonitor.com Manuals
SyncMaster 997DF
User con trol butt ons
Direct-Access Fe ature s
OSD Fu nction s
MagicTune ™
Adju sting Yo ur
Monitor
User co n tro l bu tto ns
1.
Op ens the OSD menu. Also use to exit t he OSD m enu or re turn to the p revious menu .
2.
These b uttons allow you t o highlig ht and a dju st item s in t he men u.
3.
Use to select the OSD menu .
Direct -Acces s Fe atu res
| Brightness |
| Contrast |
Downloaded from ManualMonitor.com Manuals
OSD Fu n ctio ns
OSD
Descrip tion
Adju st t he Bright ness.
Adju st t he Co ntrast.
A "Mo iré" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts.
A "Mo irë" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the vertical moire a dju stm ents.
The Degau ss fea ture will remove color im purities caused by mag netic fie lds.
Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size ,
Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire.
Note : If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings
will remain the sam e.
(Optio n)
Use this menu to choose bet ween the signal source conn ected to t he BNC connector input
and the signa l source connected to the D -SUB connector input.
Downloaded from ManualMonitor.com Manuals
Play / Stop
Note : When you a re finished, w ait for a few se con ds and the screen w ill blank then
display the ima ge from the new signal source (oth er comp uter). A cable m ust be conne cte d
to both inp uts to use this function.
OSD
Descrip tion
Play / Stop
Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. T he availa ble ran ge
is betw een 5 000 to 9300K.
Use to ad just th e monitor color setting. (Re d)
Use to ad just th e monitor color setting. (Gre en)
Use to ad just th e monitor color setting. (Blue)
When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode
exits.
OSD
Descrip tion
Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay.
Follow th ese in structions to chang e the vetical position of the m onitor's entire display.
Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display.
Follow th ese in structions to chang e the vertical size of the m onitor's entire display.
Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut.
Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or
right.
Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all.
Downloaded from ManualMonitor.com Manuals
Play / Stop
Adju st t he parallelogram sett ing when the display is leaning left or rig ht.
Adju st t he ro tation setting w hen th e entire display is tilted left or rig ht.
Adju st t he sid e pin corne r correction w hen th e top or bott om of th e displa y is too large or
sma ll.
You can see th e fre quency (u ser control mode) used by th e user, the polarit y o f the op erationa l signals, the d efault
frequ ency (defa ult mode) set wh en you bu y t he mon itor and the resolu tio n le ve l.
Note : The se screens do n ot allo w any chan ges to the set ting s, they are for inf orma tio n only.
Downloaded from ManualMonitor.com Manuals
SyncMaster 793MB/795MB
User con trol butt ons
Direct-Access Fe ature s
OSD Fu nction s
MagicTune ™
Adju sting Yo ur
Monitor
User co n tro l bu tto ns
1.
Op ens the OSD menu. Also use to exit t he OSD m enu or re turn to the p revious menu .
2.
These b uttons allow you t o highlig ht and a dju st item s in t he men u.
3.
Use to select the OSD menu .
a.
MagicBright2™ is a ne w fea ture providing opt imu m vie wing environ ment d epending on the con tents of th e im age
you are watching.
Direct -Acces s Fe atu res
| Brightness |
Downloaded from ManualMonitor.com Manuals
| MagicBright2™ |
Mag icBrig ht2™
Then push the MagicBright2 ™ button a gain to circle through a vailable preconfigured
modes.
OSD Fu n ctio ns
osd
Descrip tion
Adju st t he Bright ness.
Adju st t he Co ntrast.
A "Mo iré" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the horizonta l m oire ad justme nts.
A "Mo irë" pattern can app ear on your screen, looking like a series of concent ric circles or
arcs. To eliminat e this pattern, use the vertical moire a dju stm ents.
The Degau ss fea ture will remove color im purities caused by mag netic fie lds.
Use the recall f eature to reset these m onitor set ting s t o their o riginal le ve ls: Positio n, Size ,
Pincushion, T ra pezoid, Parallelogram, Pinba lan ce, Rotat ion , H-Moire,a nd V-Moire.
Note: If yo u have selected "Yes", all settings liste d above w ill be reset. All other settings
will remain the sam e.
Downloaded from ManualMonitor.com Manuals
Play / Stop
osd
Descrip tion
Play / Stop
Color temperature is a measure of th e 'w arm th' o f the imag e colo rs. (6500K / 9 300K)
Use to ad just th e monitor color setting. (Re d)
Use to ad just th e monitor color setting. (Gre en)
Use to ad just th e monitor color setting. (Blue)
When you a dju st t he Bright ness and C ontra st after sR GB mode is selected, sRGB m ode
exits.
osd
Descrip tion
Follow th ese in structions to chang e the ho rizontal positio n of the monitor's entire disp lay.
Follow th ese in structions to chang e the vetical position o f the m onitor's entire d isplay.
Follow th ese in structions to chang e the ho rizontal size of the mo nit or's e ntire display.
Follow th ese in structions to chang e the vertical size of the m onitor's entire display.
Adju st t he pincushio n setting w hen the sides of the displa y are b owed in or bo wed o ut.
Adju st t he pinbalance setting when the sid es of the d isplay are bow ed tow ard s th e left or
right.
Adju st t he trapezoid setting wh en the top or botto m of the disp lay is too large or sm all.
Adju st t he parallelogram sett ing when the display is leaning left or rig ht.
Downloaded from ManualMonitor.com Manuals
Play / Stop
Adju st t he ro tation setting w hen th e entire display is tilted left or rig ht.
You can see th e fre quency (u ser control mode) used by th e user, the polarit y o f the op erationa l signals, the d efault
frequ ency (defa ult mode) set wh en you bu y t he mon itor and the resolu tio n le ve l.
Note : The se screens do n ot allo w any chan ges to the set ting s, they are for inf orma tio n only.
Downloaded from ManualMonitor.com Manuals
Overview
|
Installation
|
OSD Mode
|
Uninstall
|
Troubleshooting
Overview
What is MagicTune™?
Monitor performance can v ary due to the graphics card, host c omputer lighting conditions
and other environmental factors . In order to get the best image on a monitor requires you
to adjust it for your unique setting. Unfortunately, the manual controls av ailable to tune the
image often prove to be c hallenging. Proper adjustment (tuning) requires an easy to use
program that goes through a step-by -step process to obtain the bes t overall picture quality.
In most cases even simple adjustments to Brightness, or Contrast require navigation of the
multi -level, on-screen display (OSD) menus that are not eas y to understand. Furthermore,
there is no feedback to assist in correctly setting the controls of the monitor. MagicTune is
a s oftware utility that guides you through the tuning process with easy to understand
instructions and back ground patterns designed for each monitor control.
Basic Functionality
Magic Tune is a software utility that allows monitor adjustment and color tuning using the
Display Data Channel Command Interface (DDC/CI) protocol. All adjustments to the
display are controlled via software to eliminate the need to use the monitor on-screen
display (OSD). MagicTune supports Windows 98SE, Me, 2000, NT, XP Home, and XP
Professional.
MagicTune allows for quick ac curate tuning of the display with the ability to easily save
and use monitor configurations that are best suited for you.
OSD Mode
The OSD mode allows eas y adjustment of monitor settings without taking pre -defined
steps. You can access the desired menu item to s et with ease.
Downloaded from ManualMonitor.com Manuals
Overview
|
Installation
|
OSD Mode
|
Uninstall
|
Troubleshooting
Installation
1. Ins ert the installation CD into the CD-ROM drive.
2. Click the MagicTune™ installation file.
3. Select installation Language, Click "Next".
4. When the InstallationShield Wizard window appears, click "Next."
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
Downloaded from ManualMonitor.com Manuals
6. Choose a folder to install the MagicTune program.
7. Click "Ins tall."
8. The "Installationation Status" window appears.
Downloaded from ManualMonitor.com Manuals
9. Click "Finish."
10. When the installation is complete, the MagicTune 2.5 executable icon appears on y our
desktop.
Double -click the ic on to start the program.
Magic tune ex ecution icon may not appear depending on specification of
computer sys tem or monitor. If that happens, pres s F5 Key.
11. The following window appears if the installation is successful.
Downloaded from ManualMonitor.com Manuals
12. The following error message indicates that the system is using a video card that is not
supported by MagicT une.
Installationation Problems
The ins tallation of MagicTune™ 2.5 can be affected by such factors as the v ideo card,
motherboard and the network environment.
See "Troubleshooting" if you have trouble during installation.
System Requirements
OS
z
z
z
z
z
z
Windows 98 SE
Windows Me
Windows NT
Windows 2000
Windows XP Home Edition
Windows XP Profess ional
Hardwar e
z
z
32MB Memory above
25MB Hard disk s pace above
* For more information, visit the MagicTune website .
Downloaded from ManualMonitor.com Manuals
Overview
|
Installation
|
OSD Mode
|
Uninstall
|
Troubleshooting
MagicTune allows for quick accurate tuning of the display with the
ability to easily save and use monitor configurations that are best
suited for you.
z
OSD mode may appear inconsistent with the
explanation in guidance book depending on
specification of each monitor.
OSD Mode
The OSD mode makes ers the adjustment of settings on all monitors easy. When
selected , each tab on top of the control window displays the general descriptions of
the sub -menu items for adjustment. When selected, each tab displays a list of
menus. For quick adjustment of the monitor settings, the OSD mode allows easy and
convenient access to all tabs and sub -menu items.
Button Tab Definition
OK
Applies any changes made and exits MagicTune.
Reset
Restores the monitor values displayed on the active control window
to the manufacturer-re commended values .
Exits MagicTune without applying the changes made. If you have
Downloaded from ManualMonitor.com Manuals
Cancel
not made any changes in the control window, clicking "Cancel" does
not cause any actions.
Picture Tab Definition
Allows the user to adjust the screen settings to the desired values.
Brightness MagicBright
Contrast Brightnes s
Makes the entire screen brighter or darker. The detailed data of the
images in the dark areas can be lost if the brightness is not
adjusted to the proper level. Adjust the brightness for best viewing
conditions.
Contra st
Adjusts the difference in brightness between the bright and dark
areas on screen. Determines the crispness of the images.
MagicBright™ is a new feature providing the optimum viewing
environment depending on the contents of the image you are
watching. Currently four different modes are available. Each mode
has its own pre-configured brightness value. You can easily select
one of four settings by simply pressing the MagicBright™ control
button.
z
19" or above
1. Text: For documentations or works involving heavy text.
2. Internet: For working with a mixture of images such as text
Downloaded from ManualMonitor.com Manuals
and graphics.
3. Game: For watching motion pictures such as a Game.
4. Entertain: For watching motion pictures such as a DVD or
VCD.
MagicBright™
z
Less than 19"
1. Text: For documentations or works involving heavy text.
2. Internet: For working with a mixture of images such as text
and graphics.
3. Entertain: For watching motion pictures such as a DVD or
VCD.
Color Tab Definition
Adjusts the "warmth" of the monitor background or image color.
Color
Tone
Color
Control
The tone of the color can be changed.
Color Tone
z
z
Color Control
Warm - Normal - Cool
Custom
Adjusts of the monitor image color.
You can change the monitor color to your desired color.
z
z
R- G- B
sRGB
Downloaded from ManualMonitor.com Manuals
Image Tab Definition
Adjusts the Position, Size and Rotation values.
Geometry 1
Rotation Size
Geometry 2
Pincushion
Position
Pinbalance Trapezoid Parallelogram
Other
Moire Degauss Sidepin Corner Top
Sidepin Corner Bottom Pinbalance Corner Top
Pinbalance Corner Bottom
Adjusts the Position, Size and Rotation values.
Geometry 1
z
z
z
Position
Size
Rotation
Adjusts the Pincushion, Pinbalance, Trapezoid and Parallelogram
values.
Geometry 2
z
z
z
z
Pincushion
Pinbalance
Trapezoid
Parallelogram
Adjusts the Moire, Degauss, Sidepin Corner, and Pinbalance
Corner values.
Other
z
z
z
z
Moire
Degauss
Sidepin Corner Top
Sidepin Corner Bottom
Downloaded from ManualMonitor.com Manuals
z
z
Pinbalance Corner Top
Pinbalance Corner Bottom
Option Tab Definition
You can configure MagicTune using the following options.
Loads the Preferences Dialog Box. Preferences in use will have an
"V" in the check box. To turn on or o ff any Preference, position the
cursor over the box and click.
Preferences
z
z
Enable task tray menu .
- To access the MagicTune menus, click the icon on the [task
tray menu].
The menus are not displayed if the [Enable System Tray] is
deselected in [Options] ' [Preferences].
Select Language - Th e language chosen affects only the
language of the OSD.
Support Tab Definition
Shows the Asset ID and the version number of the program, and allows you to use
the Help feature.
Downloaded from ManualMonitor.com Manuals
Help
Visit the MagicTune website or click to open the Help files (User
Manual) if you need any help installing or running MagicTune.
The User Manual opens within a basic browser window.
Asset ID
Opens a monitor info window showing the manufacturing date of
the monitor.
Version
Displays the version number of MagicTune.
Downloaded from ManualMonitor.com Manuals
Overview
|
Installation
|
OSD Mode
|
Uninstall
|
Troubleshooting
Uninstall
The MagicTune program can be removed only by using the "Add or Remove Programs"
option of the Windows Control Panel.
Perform the following steps remove MagicTune.
1. Go to [Task Tray] ' [Start] ' [Settings] and selec t [Control Panel] in the menu. If the
program runs on Windows XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, sc roll down to find "Magic Tune." Clic k
on it to highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears .
Visit the MagicTune website for technical support for MagicTune, FAQs (questions and
answers) and software upgrades.
Downloaded from ManualMonitor.com Manuals
Overview
|
Installation
|
OSD Mode
|
Uninstall
|
Troubleshooting
Troubleshooting
MagicTune may not work in case monitor is replaced or driver of graphic card is updated
while MagicTune is operating. If so, please restart the system.
Check when MagicTune does not function properly.
* MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and
Play.
* To check whether your PC is available for MagicTune feature, follow the
steps below (When Windows is XP);
Control Panel -> Performance and Maintenance -> System -> Hardware -> Device
Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play
monitor' by searching new Hardware.
Visit the MagicTune website for technical support for MagicTune, FAQs (questions and
answers) and software upgrades.
Downloaded from ManualMonitor.com Manuals
Before calling for service, check the information in this section to see if you can remedy any
problems yourself. If you do need assistance, please call, the phone number on the
Information section or contact your dealer.
Check List
Q&A
Self-Test Feature
Check
Symptom
No images on the
screen. I cannot turn
on the monitor.
Check List
Solutions
Is the power cord connected
properly?
Check the power cord connection
and supply.
Can you see "
screen?
Check the signal cable connection.
" on the
If the power is on, reboot the
computer to see the initial
screen(the login screen), which
can be seen.
If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows ME/XP/2000) and then
change the frequency of the video
card.
(Refer to the Preset Timing Modes)
Note: If the initial screen (the login
screen) does not appear, contact a
service center or your dealer.
Can you see "
screen?
" on the
You can see this message when the
signal from the video card exceeds
the maximum resolution and
frequency that the monitor can
handle properly.
Adjust the maximum resolution and
frequency that the monitor can
handle properly.
The image on the
screen is shaking.
There is no image on the
screen. Is the power indicator
on the monitor blinking at 1
second intervals?
The monitor is in PowerSaver mode.
Check the monitor configuration
to see if it is in Interlace Mode.
(Interlace Mode: Vertical
frequency 43Hz, 87Hz(i), etc)
The signal from the video card
exceeds the maximum resolution and
frequency of the monitor.
Are there any magnetic
products such as a power
adapter, speaker or a high
voltage wire near by?
Move the monitor away from
anything that can create a strong
magnetic field.
Is the voltage stable?
The screen image can appear to
shake or vibrate at a particular time
of day due to low supply voltage.
Press any key on the keyboard or
move the mouse to activate the
monitor and restore the image on the
screen.
The screen image can also appear to shake or vibrate if there is a
problem with the video card or the computer's main board.
The screen shows
strange colors or
just black and white.
Downloaded from ManualMonitor.com Manuals
Is the screen displaying only
one color as if looking at the
screen through a cellophane
Check the signal cable connection.
Make sure the video card is fully
The screen
suddenly has
become
unbalanced.
paper?
inserted in it's slot.
Have the screen colors become
strange after running a program
or due to a crash between
applications?
Reboot the computer.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
Have you changed the video
card or the driver?
Adjust screen image position and
size using the OSD.
Have you adjusted the
resolution or frequency on the
monitor?
Adjust the resolution and frequency
at the video card.
(Refer to the Preset Timing Modes).
The screen can be unbalanced due to the cycle of the video card
signals. Readjust Position by referring to the OSD.
The screen is out of
focus or OSD
cannot be adjusted.
Have you adjusted the
resolution or frequency on the
monitor?
Adjust the resolution and frequency
of the video card.
(Refer to the Preset Timing Modes).
The screen is
partially distorted.
Are there any magnetic
products such as an adapter,
speaker or a high voltage wire
near the monitor?
Enter the OSD and perform a
"Degauss".
Is the frequency properly
adjusted when checking the
Display Timing on the menu?
Adjust the frequency properly by
referring to the video card manual
and the Preset Timing Modes.
LED is blinking but
no images on the
screen.
Keep the monitor away from any
magnetic products.
(The maximum frequency per
resolution may differ from product to
product.)
There are only 16
colors shown on the
screen. The screen
colors have
changed after
changing the video
card.
Have the Windows colors been
set properly?
For Windows ME/XP/2000:
Set the colors properly at the
Control Panel, Display, Settings.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
There is a message
that reads
"Unrecognized
monitor, Plug & Play
(VESA DDC) monitor
found".
Have you installed the monitor
driver?
Install the monitor driver according to
the Driver Installation Instructions.
See the video card manual to
see if the Plug & Play (VESA
DDC) function can be
supported.
Install the monitor driver according to
the Driver Installation Instructions.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the video cables are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the "Control Panel, System, Device Administrator" and then
reboot the computer to reinstall the adapter (video) driver.
Note: If problems repeatedly occur, contact an authorized service center.
Downloaded from ManualMonitor.com Manuals
Question
How can I change the frequency?
Check List
Q&A
Answer
Frequency can be changed by reconfiguring the video
card.
Note that video card support can vary, depending on the
version of the driver used.
(Refer to the computer or the video card manual for
details.)
Self-Test Feature
Check
How can I adjust the resolution?
Windows ME/XP/2000: Set the resolution at the Control
Panel, Display, Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows ME/XP/2000: Set the function at BIOS-SETUP
of the computer or the screen saver. (Refer to
Windows/Computer Manual).
The monitor makes a sound when it
is turned on.
This is normal as some sound may be generated when
the metal case and the electromagnet, which are installed
to block any electromagnetic waves, interact with each
other.
How can I clean the outer
case/Picture tube?
Disconnect the power cord and then clean the monitor
with a soft cloth, using either a cleaning solution or plain
water.
Do not leave any remains of the detergent nor scratch the
case. Do not allow any water to go inside the monitor.
Downloaded from ManualMonitor.com Manuals
Self-Test Feature Check
| Warning Messages | Environment | Useful Tips
Your monitor provides a self test feature that allows you to check whether your monitor is
functioning properly.
Check List
Q&A
Self-Test
Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
SyncMaster 591S/793S/591V/793V/783DF/793DF
/795DF/797DF/793MB/795MB
SyncMaster 997DF
This box appears during normal operation if the video cable becomes disconnected or
damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your
video controller and computer system; your monitor is functioning properly.
If there is something wrong with the input signal, a message appears on the screen or
the screen goes blank although the power indicator LED is still on. The message may
indicate that the monitor is out of scan range or that you need to check the signal cable.
SyncMaster 591S/793S/591V/793V/783DF/793DF
/795DF/797DF/793MB/795MB
SyncMaster 997DF
The location and the position of the monitor may influence the quality and other
features of the monitor.
1. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to
another room.
2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3
feet (one meter) of the monitor.
3. Degauss the monitor if any devices were removed from the area.
Downloaded from ManualMonitor.com Manuals
z
z
A monitor recreates visual signals received from the computer. Therefore, if there is trouble
with the computer or the video card, this can cause the monitor to become blank, have poor
coloring, noise, Sync. Out of Range, etc. In this case, first check the source of the problem,
and then contact a service center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a "Sync. Out of Range" message comes up, disconnect
the cable from the computer while the monitor is still powered on.
{ If there is a message coming up on the screen or if the screen goes white, this means
the monitor is in working condition.
{ In this case, check the computer for trouble.
Downloaded from ManualMonitor.com Manuals
General
Model Name
General
PowerSaver
Preset Timing
Modes
SyncMaster 591S/591V
Picture Tube
Type
15" (38cm) Full square type (35cm viewable)
Deflection angle
90 °
Dot Pitch
0.24mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static/Glare.
Maximum Resolution
1024 x 768(NI)
Active Display
Horizontal
267 ± 4 mm
Vertical
200 ± 4 mm
Synchronization
Horizontal
30 - 55 kHz
Vertical
50 ~ 120 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
65 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
Less than 70W
Dimensions (WxDxH)
361 x 379.2 x 347 mm (After installation of Stand)
Weight
11.0 kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage
Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Downloaded from ManualMonitor.com Manuals
General
Model Name
General
PowerSaver
Preset Timing
Modes
SyncMaster 793S/793V
Picture Tube
Type
17"(43cm) Full square type (40.6cm viewable)
Deflection angle
90 °
Dot Pitch
0.23mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
Maximum Resolution
1280 x 1024 (NI)
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
110 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
Less than 90W
Dimensions (WxDxH)
401 x 410 x 378mm (After installation of Stand)
Weight
14.3kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Downloaded from ManualMonitor.com Manuals
General
Model Name
General
PowerSaver
Preset Timing
Modes
SyncMaster 793DF/793MB/783DF
Picture Tube
Type
17"(43cm) DynaFlat (40.6cm viewable)
Deflection angle
90 °
Dot Pitch
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
Maximum Resolution
1280 x 1024 (NI)
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 70 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
110 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
Less than 90W
Dimensions (WxDxH)
401 x 410 x 378mm (After installation of Stand)
Weight
14.3kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Downloaded from ManualMonitor.com Manuals
General
Model Name
General
PowerSaver
Preset Timing
Modes
SyncMaster 795DF/795MB
Picture Tube
Type
17"(43cm) DynaFlat (40.6cm viewable)
Deflection angle
90 °
Dot Pitch
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
Maximum Resolution
1600 x 1200 (NI)
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 85 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
185 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
Less than 90W
Dimensions (WxDxH)
401 x 410 x 378mm (After installation of Stand)
Weight
14.3kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Downloaded from ManualMonitor.com Manuals
General
Model Name
General
PowerSaver
Preset Timing
Modes
SyncMaster 797DF
Picture Tube
Type
17"(43cm) DynaFlat (40.6cm viewable)
Deflection angle
90 °
Dot Pitch
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
Maximum Resolution
1600 x 1200@76Hz
Active Display
Horizontal
312 ± 4 mm
Vertical
234 ± 4 mm
Synchronization
Horizontal
30 ~ 96 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
250 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
Less than 90W
Dimensions (WxDxH)
401 x 410 x 378mm (After installation of Stand)
Weight
14.3kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Downloaded from ManualMonitor.com Manuals
General
Model Name
General
PowerSaver
Preset Timing
Modes
SyncMaster 997DF
Picture Tube
Type
19"(48cm) DynaFlat (45.8cm viewable)
Deflection angle
90 °
Dot Pitch
0.20mm (Horizontal)
Screen type
Aluminized tri-color phosphor dot trio with black matrix.
Anti-doming invar shadow mask.
Multi-layer coated with anti-static.
Maximum Resolution
1600 X 1200@ 76Hz
Active Display
Horizontal
352 ± 3 mm
Vertical
264 ± 3 mm
Synchronization
Horizontal
30 ~ 96 kHz
Vertical
50 ~ 160 Hz
Input Signal Definition
Video Signal
RGB, Analog 0.7 Vpp positive at 75 ohms
Sync Signal
Separate H/V sync, TTL level, positive or negative
Display Color
Unlimited
Maximum Pixel Clock
250 MHz
Power Supply
90 ~ 264VAC rms, 60/50 Hz ± 3Hz
Power Consumption
Less than 110W
Dimensions (WxDxH)
445 x 457.5 x 416mm (After installation of Stand)
Weight
18.2 kg
Environmental considerations
Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)
Humidity 10% ~ 80%, non-condensing
Storage Temperature -4°F ~113°F (-20°C ~ 45°C)
Humidity 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Note: Design and specifications are subject to change without prior notice.
Downloaded from ManualMonitor.com Manuals
SyncMaster 591S/591V
General
PowerSaver
Preset Timing
Modes
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
State
Normal Operation
Power-off Mode EPA/ENERGY
2000
Power Indicator
Green
Green, Blinking
Power Consumption
Less than 70W
Less than 2W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when
used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets
the ENERGY STAR® guidelines for energy efficiency.
Downloaded from ManualMonitor.com Manuals
SyncMaster 793S/793V/783DF/795DF
793DF/797DF/793MB/795MB
General
PowerSaver
Preset Timing
Modes
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
State
Normal Operation
Power-off Mode EPA/ENERGY
2000
Power Indicator
Green
Green, Blinking
Power Consumption
Less than 90W
Less than 2W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when
used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets
the ENERGY STAR® guidelines for energy efficiency.
Downloaded from ManualMonitor.com Manuals
SyncMaster 997DF
General
PowerSaver
Preset Timing
Modes
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
State
Normal Operation
Power-off Mode EPA/ENERGY
2000
Power Indicator
Green
Green, Blinking
Power Consumption
Less than 110W
Less than 2W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when
used with a computer equipped with VESA DPMS functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets
the ENERGY STAR® guidelines for energy efficiency.
Downloaded from ManualMonitor.com Manuals
SyncMaster 591S/591V
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
General
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
37.500
85.008
36.000
-/-
VESA, 640 x 480
43.269
75.000
31.500
-/-
VESA, 800 x 600
53.674
85.061
56.250
+/+
PowerSaver
Preset Timing
Modes
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Downloaded from ManualMonitor.com Manuals
SyncMaster 793S/793V/783DF/793DF793MB
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
General
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
53.674
85.061
56.250
+/+
VESA, 1024 x 768
68.677
84.997
94.500
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
PowerSaver
Preset Timing
Modes
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Downloaded from ManualMonitor.com Manuals
SyncMaster 795DF/795MB
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
General
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 1024 x 768
68.677
84.997
94.500
+/+
VESA, 1280 x 1024
79.976
75.025
135.00
+/+
PowerSaver
Preset Timing
Modes
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Downloaded from ManualMonitor.com Manuals
SyncMaster 797DF/997DF
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
General
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 1024 x 768
68.677
84.997
94.500
+/+
VESA, 1280 x 1024
91.146
85.024
157.50
+/+
PowerSaver
Preset Timing
Modes
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Downloaded from ManualMonitor.com Manuals
Service
Terms
Regulatory
Natural Color
Authority
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
http://www.samsung.com.au/
BRAZIL :
Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
SAC : 0800 124 421
http://www.samsung.com.br/
CANADA :
Samsung Electronics Canada Inc.
Samsung Customer Care
7037 Financial Drive
Mississauga, Ontario
L5N 6R3
1-800-SAMSUNG (1-800-726-7864)
http://www.samsung.ca/
CHILE :
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
http://www.sonda.com/
http://www.samsung.cl/
COLOMBIA :
Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 - 2068
http://www.samsung-latin.com/
e-mail : soporte@samsung-latin.com
ESPAÑA :
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
http://samsung.es/
FRANCE :
SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
http://www.samsungservices.com/
GERMANY :
TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0.12/Min
http://www.samsung.de/
Downloaded from ManualMonitor.com Manuals
HUNGARY :
Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
http://www.samsung.hu/
ITALY :
Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153
http://www.samsung-italia.com/
MEXICO :
SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V.
Via Lopez Portillo No. 6, Col. San Francisco
Chilpan Tultitlan, Estado de Mexico C.P. 54940, Mexico D.F. Mexico
Tel : 01(55) 5317 2551/3410/3409
Fax : 01(55) 5317 3377
RFC: SEM950215S98
http://www.samsung.com.mx/
IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V.
Via Lopez Portillo No. 6, Col. San Francisco
Chilpan Tultitlan, Estado de Mexico C.P. 54940, Mexico D.F. Mexico
Tel : 01(55) 5317 2551/3410/3409
EXPORTADO POR: Samsung Electronics CO.,LTD.
416, Mae tan-3dong, Yeongtong-gu,
Suwon City, Kyoungki-Do Korea
NETHERLANDS/BELGIUM/LUXEMBOURG :
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
PANAMA :
Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
http://www.samsung-latin.com/
PERU
Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
http://www.samsungperu.com/
PORTUGAL :
SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128
Free Line 800 220 120
http://www.samsung.pt/
SOUTH AFRICA :
Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
http://www.samsung.co.za/
Downloaded from ManualMonitor.com Manuals
SWEDEN/DENMARK/NORWAY/FINLAND :
Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
Fax +46 8 590 966 50
http://www.samsung.se/
THAILAND :
HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
UKRAINE :
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
http://www.samsung.com.ua/
United Kingdom :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
http://samsungservice.co.uk/
U.S.A. :
Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
http://samsungusa.com
Downloaded from ManualMonitor.com Manuals
Dot Pitch
Service
The image on a monitor is composed of red, green and blue dots. The closer the dots, the
higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'.
Unit: mm
Terms
Vertical Frequency
Regulatory
The screen must be redrawn several times per second in order to create and display an image
for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh
Rate. Unit: Hz
Natural Color
Authority
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is
called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of monitors to ensure a clear image.
The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and
the monitor to exchange information automatically. This monitor follows the international
standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for
performing multiple tasks as more image information can be shown on the screen.
Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal
dots (horizontal resolution) and 768 vertical lines (vertical resolution).
Downloaded from ManualMonitor.com Manuals
Regulatory
Service
Terms
Regulatory
Natural Color
FCC Information | IC Compliance Notice | MPR II Compliance |
European Notice (Europe only) | PCT Notice | VCCI | CCC Notice
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)
TCO'99-Ecological requirements for personal computers (TCO'99 applied model only)
TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)
TCO'03 Recycling Information (TCO'03 applied model only)
Authority
You must right-click the link for a portable document format (PDF) file and save the file to your hard-disk drive.
Attempting to link directly to large PDF files causes your system to freeze.
Regulatory (PDF Document)
- To save PDF files (files with an extension of .pdf ) to your hard-disk drive, right-click the document title, click
Save Target As in Microsoft® Internet Explorer or Save Link As in Netscape Navigator, and specify a location
on your hard-disk drive. To view a PDF file, launch Adobe™ Acrobat Reader. Click File —> Open and select
the PDF file. Note : You need to run Adobe Acrobat Reader to View PDF Documents.
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the following
warning:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television receptions,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment. If necessary, consult your dealer or an experienced
radio/television technician for additional suggestions. You may find the booklet called How to Identify and
Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal
Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC
20402, Stock Number 004-000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Tel) 949-975-7310
Fax) 949-922-8301
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be
suitable for connection to any UL Listed personal computer with similar configuration. Before making the
connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor
and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage
rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type
Downloaded from ManualMonitor.com Manuals
(parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with
NEMA configuration 6-15P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations of ICES-003.
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur les
équipements produisant des interférences au Canada.
MPR II Compliance
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
European Notice (Europe only)
Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC),
(93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following European Norms:
z EN55022:1998+A1:2000 - Radio Frequency Interference
z EN55024:1998 - Electromagnetic Immunity
z EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics
z EN61000-3-3:1995 - Voltage Fluctuations
PCT Notice
VCCI
This is a Class B product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment according to the instruction
manual.
CCC Notice
Downloaded from ManualMonitor.com Manuals
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed to
reducing the burden on the environment and to the further development of environmentally-adapted
electronic products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment.The main problem as far as monitors and other
electronic equipment are concerned is that environmentally harmful substances are used both in the
products and during their manufacture. Since it has not been possible so far for the majority of electronic
equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or
later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are important
from both the working and natural environment viewpoints. Since all types of conventional electricity
generation have a negative effect on the environment (acidic and climate-influencing emissions,
radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an
enormous amount of energy, since it is often routinely left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international
environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The
Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for
Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in
Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical
and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product
must be prepared for recycling and the manufacturer is obliged to have an environmental plan, which must
be adhered to in each country where the company conducts its operations policy. The energy requirements
include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to
a lower level, in one or more stages. The length of time to reactivate the monitor shall be reasonable for
the user.
Labelled products must meet strict environmental demands, for example in respect of the reduction of
electric and magnetic fields, along with physical and visual ergonomics and good usability.
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by this
product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO'95-approved and labelled products may also
be obtained via the Internet, using the address:
http://www.tco-info.com/
TCO'95 is a co-operative project between(3 logos)
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In
turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of
flame retardant substances. These are related to another group of environmental toxins, PCBs, which are
suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals,
due to the bioaccumulative processes. Flame retardants have been found in human blood and researchers
fear that disturbances in foetus development may occur.
z TCO'95 demand requires that plastic components weighing more than 25 grams must not contain
organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning.
Downloaded from ManualMonitor.com Manuals
z
TCO'95 requirement Permits the inclusion of lead since no replacement has yet been developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses.
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
cadmium. The colour-generating layers of display screens must not contain any cadmium.
z
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and
is toxic in high doses.
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
mercury. It also demands that no mercury is present in any of the electrical or electronics components
concerned with the display unit.
z
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of
expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of
skin cancer (malignant melanoma).
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the manufacturing of
the product or its packaging.
z
TCO'99-Ecological requirements for personal computers (TCO'99 applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a
product developed for professional use. Your purchase has also contributed to reducing the burden on the
environment and also to the further development of environmentally adapted electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international
environmental and quality labelling labelling of personal computers. The labelling scheme was developed
as a joint effort by the TCO(The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens Energimyndighet(The
Swedish National Energy Administration) and SEMKO AB.
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of electric
and magnetic fields, energy consumption and electrical safety.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and other
electronics equipment are concerned, is that environmentally harmful substances are used both in the
products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of
electronics equipment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing
emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running
continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish
Society for Nature Conservation). These demands impose restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs(freons)and chlorinated solvents, among other
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental policy which must be adhered to in each country where the company implements its
operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
Downloaded from ManualMonitor.com Manuals
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labelled products may also be obtained via the
Internet, using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose
is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can
consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame
retardants are chemically related to another group of environmental toxins, PCBs. Both the flame
retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health
effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*
processes. Flame retardants have been found in human blood and researchers fear that disturbances in
foetus development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the
printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99
requirement states that batteries, the colour-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic
in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light
system of flat panel monitors as today there is no commercially available alternative. TCO aims on
removing this exception when a Mercury free alternative is available.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit
boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing
increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant
melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the
inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)
Congratulations!
The display you have just purchased carries the TCO'03 Displays label. This means that your display is
designed, manufactured and tested according to some of the strictest quality and environmental
requirements in the world. This makes for a high performance product, designed with the user in focus that
also minimizes the impact on our natural environment.
Some of the features of the TCO'03 Display requirements:
Ergonomics
Good visual ergonomics and image quality in order to improve the working environment for the user and to
Downloaded from ManualMonitor.com Manuals
reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance,
colour rendition and image stability.
Energy
z Energy-saving mode after a certain time-beneficial both for the user and the environment
z Electrical safety
Emissions
z
z
Electromagnetic fields
Noise emissions
Ecology
The product must be prepared for recycling and the manufacturer must have a certified
management system such as EMAS or ISO 14 000
z Restrictions on
o chlorinated and brominated flame retardants and polymers
o heavy metals such as cadmium, mercury and lead.
z
environmental
The requirements included in this label have been developed by TCO Development in cooperation with
scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has
been involved in influencing the development of IT equipment in a more user-friendly direction. Our
labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over
the world.
For more information, Please visit
www.tcodevelopment.com
TCO'03 Recycling Information (TCO'03 applied model only)
[European Residents Only]
For recycling information for TCO'03 certified monitors, for the residents in the following countries, please
contact the company corresponding to your region of residence. For those who reside in other countries,
please contact a nearest local Samsung dealer for recycling information for the products to be treated in
environmentally acceptable way.
[U.S.A. Residents Only]
U.S.A.
COMPANY
Solid Waste Transfer &
Recycling Inc
ADDRESS
442 Frelinghuysen Ave
Newark, NJ 07114
TELEPHONE 973-565-0181
FAX
Fax: 973-565-9485
Enone
MAIL
http://www.bcua.org/Solid
HOME
Waste_Disposal6.htm
PAGE
Downloaded from ManualMonitor.com Manuals
[European Residents Only]
SWEDEN
ELKRETSEN
ELKRETSEN Box
1357, 111 83
Stockholm
Barnhusgatan 3, 4 tr.
08-545 212 90
08-545 212 99
NORWAY
GERMANY
Elektronikkretur AS
vfw AG
6454 Etterstad 0602 Oslo
Fyrstikkalln 3B
Max Plank Strasse 42
50858 Collogne
Germany
23 06 07 40
23 06 07 41
49 0 2234 9587 - 0
info@el-kretsen.se
adm@elektronikkretur.no
vfw.info@vfw-ag.de
http://www.elkretsen.se/
http://www.elretur.no/
Natural Color Software Program
Service
Terms
Regulatory
Natural Color
Authority
One of the recent problems in using a computer is that the color of the images printed out by a
printer or other images scanned by a scanner or a digital camera are not the same as those
shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the
color of the images on the monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial
screen of the program installation will be executed. Click Natural Color on the initial screen to
install the Natural Color software. To install the program manually, insert the CD included with
the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then
select [Execute].
Enter D:\color\eng\setup.exe and then press the key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select [Setting]/[Control Panel] on the [Start] menu and then double-click [add/Delete a
program].
Select Natural Color from the list and then click the [add/Delete] button.
Downloaded from ManualMonitor.com Manuals
Information in this document is subject to change without notice.
© 2004 Samsung Electronics Co., Ltd. All rights reserved.
Service
Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.
Terms
Regulatory
Natural Color
Authority
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and
logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an
ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein
may be the trademarks or registered trademarks of their respective owners.
Downloaded from ManualMonitor.com Manuals