WASHING MACHINE
SWV-1200F/1100F/1000F/800F
P1291/P1091/P8091/P6091
SERVICE
WASHING MACHINE
Manual
CONTENTS
1. SPECIFICATIONS
2. OVERVIEW OF THE WASHING MACHINE
3. OVERVIEW OF THE CONTROL PANEL
4. PROCESS TABLE
5. GENERAL REEOR FUNCTION
6. TROUBLE DIAGNOSIS
7. TEST MODE
8. DESIGNATION OF MAIN COMPONENTS
9. PCB SHEMATIC DIAGRAM
PCB CIRCUIT DIAGRAM
PCB PATTERN DIAGRAM
WIRING DIAGRAM
10.ASSEMBLE AND DISASSEMBLE
11.TOOLS FOR DISASSEMBLY AND ASSEMLY
12.EXPOLDED VIEW AND PARTS LIST
! Caution for the safety during servicing
1. Do not allow the customer to repair the product.
☞ The person may be injured or the product life may be shortened.
2. Execute A/S after unplugging the power supply unit.
☞ Be care of the electric shock.
3. Do not plug several plugs in the same outlet.
☞ It may cause the fire due to overheat.
4. Check the damage, pressing or burning of the power plug or outlet.
☞ Replace it promptly if it has problem.(It may cause the electric shock or fire)
5. Do not clean the main body with the water.
☞ It may cause the electric shock and fire and shorten the product life)
6. The wiring of the harness shall be free from the moisture and tightened during serving.
☞ It shall not be deviated by certain impact.
7. Remove any dust or filth on the housing section,wiring section,connection section during servicing.
☞ Protect the cause of the fire such as the tracking,shortage and etc.
8. Check any mark of the moisture on the electrical parts, harness section and etc.
☞ Replace the parts or remove the moisture.
9. Check the assembly status of the parts after servicing.
☞ Maintain the status before servicing.
10. Pull out the power cord with holding the plug.
☞ Be care of the electric shock and fire when the cord is damaged.
11. Unplug the power plug from the outlet when the wash machine is not used.
☞ Be care of the electric shock and fire due to the strike of the lightening.
12. Do not use or store the spray or flammable materials(including gasoline,alcohol and etc.)
around the wash machine.
☞ Be care of the explosion or fire due to the electric spark.
13. Do not put the bowl of water or wet laundry on the wash machine.
☞ If the water is penetrated to the wash machine, this may cause the electric shock or fire.
14. Do not install the wash machine in the place where the snow or rain falls.
☞ It may cause the electric shock and fire and shorten the product life.
15. Do not push the control buttons with the awl,pin, or sharp materials.
☞ It may the electric shock and trouble.
16. Check the wash machine is leveled horizontally and installed properly on the floor.
☞ The vibration may shorten the product life.
17. Joint the wire by the connector correctly.
☞ When the wire is jointed by the tape, this may cause the fire due to the tracking.
18. When the wash machine is to be laid for the service, put the pad on the floor and lay the
product at side slowly.
☞ If the wash machine is laid front, the relay may be damaged by the tub.
19. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut.
☞ If the wash-heater is not inserted in the bracket-heater properly, this may cause the noise and
leakage since it is contacted to the drum.
2
SAMSUNG ELECTRONICS CO., LTD
1. Specifications
WASH TYPE
DIMENSION
FRONT LOADING TYPE
GROSS
W 669mm X D 656mm X H 910mm
NET
W 598mm X D 550mm X H 844mm
WATER PRESSURE
WEIGHT
50 kPa ~ 800 kPa
GROSS
80 kg
NET
75 kg
WASHand SPIN CAPACITY
POWER CONSUMPTION
5.0 kg (DRY LAUNDRY)
WASHING
220 V
180 W
240 V
180 W
WASHING and
220 V
2000 W
HEATING
240 V
2400 W
MODEL
P6091
220 V
380 W
430 W
500 W
550 W
550 W
240 V
380 W
430 W
500 W
550 W
550 W
SPIN
SWV-800F/P8091 SWV-1000F/P1091 SWV-1100F SWV-1200F/P1291
PUMPING
34 W
WATER CONSUMPTION
SPIN REVOLUTION
54 (STANDARD COURSE)
MODEL
P6091
rpm
600
SAMSUNG ELECTRONICS CO., LTD
SWV-800F/P8091 SWV-1000F/P1091 SWV-1100F SWV-1200F/P1291
800
1000
1100
1200
3
2. Overview of the Washing Machine
WATER SUPPLY VALVE
CONTROL-PANEL
ASSY DOOR
DRAWER
SENSOR
PRESSURE
TUB
ADJUSTABLE LEG
ASSY PUMP
HOSE DRAIN(OPTION)
CAP DRAIN(OPTION)
POWER CORD
BUFFER
SPRING
WEIGHT-BALANCE
DRAIN
HOSE
PULLEY
BELT
ASSY MOTOR
4
SHOCK
ABSORBER
SAMSUNG ELECTRONICS CO., LTD
3. Overview of the control panel
SWV-1200F/1100F/1000F, P1291/1091
1
2 5
3
4 7
6
8
9
1
2 9
3
4 7
6
8
10
1
2 11 12 3 7
6
8
10
10
SWV-800F/P8091
P6091
1. Detergent dispenser
2. Display panel
Displays the remaining wash cycle time, error messages and cancel —.
3. Temperature selection button
Press the button repeatedly to cycle through the available water temperature options
(cold water, 30°C, 40°C, 60°C and 95°C).
4. Spin selection button
Press the button repeatedly to cycle through the available spin speed options
SWV-1200F/P1291 : (No spin, Rinse hold, 400, 600, 800, 1000and 1200rpms),
SWV-1100F
: (No spin, Rinse hold, 400, 600, 800, 1000and 1100rpms),
SWV-1000F/P1091 : (No spin, Rinse hold, 400, 600, 800, and 1000rpms),
5. Delay Start button(OPTION)
Press the button repeatedly to cycle through the available delayed start options
(from 1 hour to 24 hours in one hour increments).
SAMSUNG ELECTRONICS CO., LTD
5
6. Course button
Press the button repeatedly to select available wash programs
7. Manual button
Press the button repeatedly to cycle through the available partial wash options
[Wash+Rinse+Spin➔ Prewash+Wash+Spin➔Spin➔Rinse(1 time)+Spin➔
Rinse(2 times)+Spin➔Rinse(3 times)+Spin]
in case P6091
[Wash+Rinse+Spin➔ Prewash+Wash+Spin➔Spin➔Rinse(3 times)+Spin]
Note : Prewash is only available when washing cotton, synthetic or delicate.
8. Start/Pause button
Press to pause and restart programs.
9. Door Open button(OPTION)
Press to open the washing machine door.
10. O (On/Off) button
Press once to turn the washing machine on, press again to turn the washing machine off. If the
washing machine power is left on for longer than 10minutes without any buttons being touched,
the power automatically turns off.
11. No Spin button(OPTION)
Press to no spin program.
12. Rinse Hold button(OPTION)
Press to rinse hold program.
6
SAMSUNG ELECTRONICS CO., LTD
5. General Error Function
•· When an error occurs, this function starts to keep generating error melody sounds and displays error
indicators as shown in the followings per corresponding error by blinking in 0.5sec interval until the error status
is completely cleared out. In this case, all the driving devices are turned off until the error is cleared out.
1. WATER SUPPLY ERROR
- Water Supply Error occurs when water level frequency does not show changes more than 50Hz or water
is not supplied up to the water level presetting for 20 min or more at the time of initial water supply, the
error status can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status.
- Display shows ‘E1’.
2. WATER DRAIN ERROR
- In case the water level frequency is 25.3KHz or less in the initial phase of UNB-detecting cycle.
- Water Drain error can be cleared by turning POWER S/W OFF and resuming the POWER ON initial status.
- Display shows ‘E2’.
3. OVER-FLOW ERROR
- Over-Flow error occurs when the water level is in abnormal operation (OVER-FLOW: 22.40KHz/50ߧ or
more). It can be cleared by turning POWER S/W OFF. Water is drained prior to POWER S/W OFF and it
is forced to be drained for 2 min if a frequency of more than 25.24 KHz is detected.
- Display shows ‘E3’.
4. DOOR OPEN ERROR
- Door Open error can be cleared by closing the door.
- Display shows ‘dE’.
5. UNBALANCE ERROR
- Unbalance error is cleared by POWER S/W OFF and by resuming the POWER ON initial status.
- Display shows ‘E4’.
6. WATER HEATER ERROR
- In case the water temperature varies by 40°C or more in 5 min, or by 2°C or less in 10 min after heating is started.
- It can be cleared by turning POWER S/W OFF.
- Display shows ‘E5,E6’.
7. ASS’Y PRESSURE S/W ERROR
* Generated Frequency Signal of WATER LEVEL(W/L) S/W (KHz)
Lvevl
Low Level
High Level
Abnormal W/L Frequency
30.00 KHz
15.00 KHz
- If the same signal as the above table is detected for more than 5 seconds, it is a PRESSURE S/W Error.
- When the error occurs, perform the time-drain for 3 min and then turn off the water drain pump. Then the
display shows ‘E7’ as a pressure s/w error indicator.
8. ABNORMAL WATER TEMPERATURE ERROR
Course
Water Temp
Synthetic
Delicate
Wool
60˚C or more
45˚C or more
45˚C or more
- In case the water temperature is 60°C or more in the synthetic course, 50°C or more in the delicate
course, and 40°C or more in the wool course.
- At the time of initial water supply, if the water temperature is not appropriate, water starts to be drained
and it is forced to be drained for 2 min when the abnormal frequency of 25.24KHz is detected.
- Display shows ‘E8’.
- This error can be cleared by POWER S/W OFF.
SAMSUNG ELECTRONICS CO., LTD
7
6. Trouble Diagnosis
°· As the micom wash machine is configured of the complicate structure, there might be the service call.
Below information is prepared for exact trouble diagnosis and suitable repair guide.
Caution for the Repair and Replacement
Please follow below instruction for the trouble diagnosis and parts replacement.
1) As some electronic components are damaged by the charged static electricity from the resin part of wash
machine or the human body, prepare the human body earth or remove the potential difference of the
human body and wash machine by contacting the power supply plug when the work contacting to PCB is
executed.
POWER SUPPLY PLUG
2) Since AC220~240V is applied to the triac T1 and T2 on P.C.B, the electric shock may occur by touching
and be careful that the strong and weak electricity are mixed.
3) If the P.C.B assembly is out of order, do not replace the component on P.C.B except TACT switch since
the component is coated by the urethane.
4) As the P.C.B assembly is designed for no trouble, do not replace the P.C.B assembly by the wrong
diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally.
5) As the parts on P.C.B are coated by the urethane, they can not be tested by the test bar of the meter.
Check the trouble by the test mode method according to the procedure.
8
SAMSUNG ELECTRONICS CO., LTD
6. Trouble Diagnosis
No
Item
1
The power is not supplied
2
The water is not supplied.
3
The wash does not start though
the water supply is stopped.
4
The wash is executed while
the water is supplied.
The drum does not rotate
during washing.
5
6
7
The drum rotates by one direction
during washing. (The drum rotates
to one direction for SPIN.)
Drainage problem.
8
Dehydration problem.
9
Abnormal noise during SPIN.
10
Leak breaker or current/leak
breaker is down during washing.
11
The heating is not executed.
SAMSUNG ELECTRONICS CO., LTD
Cause and treatment
- Is the PCB connector connected well?
- Is the voltage normal?
- Is the power supply plug connected well?
- Is the noise filter connected well?
- Is the secondary output of the power supply transformation normal?
- Is the fuse disconnected?
• If above points are not found, the PCB assembly is out of order.
Replace it.
- Is the knob open?
- Did you push START/PAUSE button after selecting the course?
- Is the water supply valve connected well?
- Is the winding of the water supply valve continuous?
- Is the connection and operation of the pressure switch normal?
• If above points are not found, the PCB assembly is out of order.
Replace it.
- Is the connection and operation of the pressure switch normal?
- Is the pressure switch hose damaged so that the air is leaked?
- Is the pressure switch hose bent?
- Check the operation of the water level switch.
• If above points are not found, the PCB assembly is out of order.
Replace it.
- The PCB assembly is out of order. Replace it.
- Is the belt connected well?
- Is the winding of the motor continuous?
(Rotor winding, stator winding, generator)
- Is the motor fuse normal?
• If above points are not found, the PCB assembly is out of order.
Replace it.
- The PCB assembly is out of order. Replace it.
(Inversion relay open trouble)
- Is the drainage hose bent?
- Is the winding of the drainage pump continuous?
- Is the drain filter clogged by the waste?
• If above points are not found, the PCB assembly is out of order.
Replace it.
- The unbalance is detected.
- Put in the laundry uniformly and start again.
- Is the pulley nut loosen?
- Is the transport safety device removed?
- Is the product installed on the level and stable place?
(Little noise may be generated during the high-speed SPIN.)
<When the leak breaker and current breaker is installed separately>
- When the leak breaker is down, check and make the earth of the outlet.
- When the current is down, the current is leaked.
<Is the breaker down when the leak/current breaker is combined?>
- Check the rated capacity of the current and leak breaker.
The current breaker may be down due to the lack of the current when the
wash machine and other apparatus are used.
In this case, execute the cold water wash to check whether the current
capacity is lack.
- Is the wash heater terminal unplugged?
- Is the wash heater normal?(Resistance value : 20.5~21.5Ω)
- If above points are not found, the PCB assembly is out of order.
Replace it.
9
7. Test Mode
1
2
3
1. Driving Compartment Test Mode
A. Hold down “2” and ”1” keys simultaneously and then press O(POWER S/W) on.
(Display shows “tE”)
Hold down “1” and “2” keys simultanesously (each processing for 0.3sec) and then
press O(POWER S/W) on.
B. The driving compartment can be tested when you press “3” key right after entering
into the intial stage of the TEST MODE.
■ Driving Compartment Test
Pre-wash VALVE ON(0.3sec) ➔ OFF(0.3sec) ➔ Main wash(0.3sec) ➔ OFF(0.3sec) ➔
Rinse VALVE ON(0.3sec) ➔ OFF(0.3sec) ➔ Pump MOTOR ON(0.3sec) ➔ OFF(0.3sec) ➔
MOTOR RELAY1 ON(0.3sec) ➔ OFF(0.3sec) ➔ MOTOR RELAY2(0.3sec) ➔ OFF(0.3sec) ➔
MOTOR RELAY2 ON(0.3sec) ➔ OFF(0.3sec) ➔ HEATER RELAY ON(0.3sec) ➔ OFF(0.3sec) ➔
DOOR OPEN (Function continues when door is closed)
10
SAMSUNG ELECTRONICS CO., LTD
8. Designation of Main Components
8-1 Normal / Reverse Revolution of Motor and R. P. M. Control
8
Rotor
CW
9
-
+
CCW
5
Stator coil
PROTECTOR
(150 C)
10
ROTOR
Stator coil
MIDDLE-SPEED
5
1 2 3 4 5 6 7 8 9 10
+
STATOR
9
TACHO
Rotor
HIGH-SPEED
8
STATOR
10
5
WASHING MOTOR
<Figure1>
<Figure2>
H
<Figure3>
STATOR(5.10) STATOR(5.1) ROTOR(8.9) TACHO(3.4) PROTECTOR(6.7) “H”(mm)
Code-No
Resistance value
1.64 Ω
0.91 Ω
1.9 Ω
42.7 Ω
0
52
DC31-10181A
2.07 Ω
0.90 Ω
2.35 Ω
42.7 Ω
0
45
DC31-00002C
Rated value
220~240V / 50Hz
Remark
A
B
8-2 Door safety Device
Solenoid
220/240V
ED 1.0%
KB 1s
SD 100s
220/240V
ED 1.0%
KB 1s
SD 100s
12A 125~250V AC
SOLENOID
Coil Resistance
210 Ω ± 10%
DC61-00115A
DC61-00122A
8-3 Heater
1) Capacity : AC 230V/2000W
2) Location : Bottom of TUB
3) Function : Raise the water temperature
supplied at the wash process.
4) Resistance value : 23Ω ~ 29Ω
5) Thermo Fuse : 128°C
SAMSUNG ELECTRONICS CO., LTD
Thermistor
11
8-4 ASSY-TUB
INNER-BEARING
OUT-BEARING
A
B
C
OIL-SEAL
(unit : mm)
TYPE INNER-BEARING(A) OUT-BEARING(B) OIL-SEAL(C)
CODE-NO
REMARK
I
ø 30
ø 25
ø 43.9
DC97-00214A SPIN SPEED OVER 1000rpm
II
ø 20
ø 17
ø 24.3
DC97-00214B SPIN SPEED BELOW 800rpm
8-5 ASSY- FLANGE SHAFT
C
B A
(unit : mm)
12
TYPE
(A)
(B)
(C)
CODE-NO
REMARK
I
ø 25
ø 30
ø 44.7
DC97-00216A SPIN SPEED OVER 1000rpm
II
ø 17
ø 20
ø 25
DC97-00214A SPIN SPEED BELOW 800rpm
SAMSUNG ELECTRONICS CO., LTD
9. PCB Schematic Diagram
SWV-1200F/100F/1000F/800F, P1291/P1091/P8091
P6091
SAMSUNG ELECTRONICS CO., LTD
13
9. PCB CIRCUIT DIAGRAM
14
SAMSUNG ELECTRONICS CO., LTD
10. Assemble and Disassemble
1. ASS’Y-COVER TOP
1) Remove two screws fixing the top-cover on back side.
2) Push the top-cover back about 15mm and pull it up.
3) It’s possible to exchange and service the trans
former, the pressure-senser, the noise-filter and
the water valve.
m
15m
SCREW
2. FRAME FRONT
1) Remove the top-cover and the ass’y drawer.
2) Remove two screws fixing the control-panel on
front side and the screw on right side.
3) Remove the cover-front(L) by using the (-)driver.
4) Pull the lever and open the ass’y-door.
5) Part the diaphragm and the wire diaphragm
away from the frame-front.
6) Remove the eight screws fixing the frame-front.
7) It’s possible to exchange and service the heater,
the pump, the shock-absorber and the door lock
s/w.
LEVER
16
SAMSUNG ELECTRONICS CO., LTD
10. Assemble and Disassemble
3. BELT
1) Remove the top-cover.
2) Disassemble and assemble the belt.
3) Check the belt is located at center of the motor-pulley.
<When assemble the belt>
Hook the belt on the motor pulley 1) and place it
around the pulley 2).
2
PULLEY
BELT
1
MOTOR
4. MOTOR
1) Lay down the washer on left side.
2) Remove the wire housing from the motor.
3) Remove the bolt fixing the motor with the box
drive on back side.
4) Remove the motor.
Motor Assemble Hole
5. How to Assemble the RELAY Housing.
<CAUTION>
Insert the Relay Housing to the Relays on the
opposite direation each other.
Relay
RELAY Housing
Heat Sink
SAMSUNG ELECTRONICS CO., LTD
17
11. Tools for Disassembly and Assembly
NO
1
2
TOOL
Box driver
10mm
Heater (1)
13mm
Motor (1), Balance (5)
17mm
2 holes of each left and right of the shock absorber
19mm
1 Pulley hole
Double-ended
10, 13
Replaceable for the box driver.
spanner
17, 19mm
Since the bolt runs idle when the box driver is used, use the box
driver 17mm.
3
Vice pliers
Tool to protect the idle and abrasion of the bolt for the box driver.
4
Other(Driver, Nipper, Long nose)
5
JIG for the Tub
General tools for the after service.
1 (Disassemble and Assemble)
10
19
13
8
12
17
10
mm
13
mm
17
mm
19
mm
18
SAMSUNG ELECTRONICS CO., LTD
12. Expolded View and Parts List
13
12
11
10
9
8
14
7
15
6
5
4
3
2
1
NO
Code No
Q'ty
Description
Specification
1
DC47-00001A
1
HEATER
230V,2000W,230V,2000W,P6091
2
DC61-30346A
1
TUB-FRONT
FRPP(GR30%),IVORY,SWF-P12
3
DC61-40348B
5
BRACKET-NUT
SBHG-R,T3,P1291,NO-PAINT
4
DC61-40344A
1
BRACKET-HEATER
STS430,T1,SWF-P12,-
5
DC61-60496A
2
SPACER-HEATER
PBT,SWF-P12,-
6
DC60-20061C
3
SCREW TAPPING
TH,+,2,D4,L12,STS304,-
7
DC62-20311A
1
VANE-CHECK
EPDM,BLK,SWF-P12,-
8
DC60-60188A
1
WASHER-PLAIN
-,ID4.5,OD15.5,T1,SWF-P12,STS3
9
DC60-20061C
1
SCREW TAPPING
TH,+,2,D4,L12,STS304,-
10
DC91-12281A
1
ASSY-DRUM
SWF-P12,-
11
DC62-40183A
1
PACKING-TUB
EPDM,BLK,SWF-P12
12
DC97-00214A
1
ASSY TUB-BACK
,P1291/P1091
12-1
DC97-00214B
1
ASSY TUB-BACK
,P8091/P6091
NSA
Remark
See on page12
13
DC61-60499B
8
CLIP-TUB
HSWR,P1291,NO/PAINT
14
DC61-60520A
1
CLIP-TUB
SK5,SWF-P12,PLATE-TYPE
15
DC97-00216A
1
ASSY-FLANGE SHAFT
P1291/P1091, ALDC+SM45C
See on page12
15-1
DC97-00214A
1
ASSY-FLANGE SHAFT
P8091/P6091, ALDC+SM45C
See on page12
SAMSUNG ELECTRONICS CO., LTD
19
12. Expolded View and Parts List
13
12
26
25
24
22
10
8
29
9
28
11
27
10
16
17
19
20
21
5
4
6
7
18
3
2
1
20
SAMSUNG ELECTRONICS CO., LTD
12. Expolded View and Parts List
NO Code No Q'ty Description
Specification
1
DC91-12078A
1
ASSY-WIRE DIAPHRAGM
SWF-P12,-
2
DC61-20219A
1
DOOR-DIAPHRAGM
EPDM,GRY,SWF-P12
3
DC91-12077A
1
ASSY-CLAMP DIAPHGRAM
SWF-P12,-
4
DC60-40138A
2
BOLT-W.MOTOR
SM10C,HEX,M8,L62,-,ZPC2(YEL),-,-
5
DC60-60044B
5
WASHER-PLAIN
SBC,ID8.4,OD30,T3,-,-,-
6
DC60-60040A
3
WASHER-NYLON
-,ID10.5,OD32,T2,-,PBSP-1/2H
7
DC66-60154A
1
WEIGHT-BALANCER
CONCRETE,SWF-P12,LOWER
8
DC61-60497A
1
CLAMP-HOSE
HSWR,SWF-P12,ID70/OD75.8(TUB)
9
DC62-10305A
1
HOSE-DRAWER TUB
EPDM,ID35,BLK,L158,SWF-P12/OD4
10
DC60-40140A
2
BOLT-HEX
WEIGHT-UL/SM10C,HEX,M8,L147,-,ZPC2(YEL)
11
DC60-40132B
1
BOLT-FLANGE
M8,L210,ZPC2(YEL),SS41C
12
DC62-10303A
1
HOSE-AIR
EPDM,ID24,BLK,L130,SWF-P12/OD4
13
DC66-60153A
1
WEIGHT-BALANCER
CONCRETE,SWF-P12,UPPER
16
DC62-40184A
1
PACKING-TRAP
EPDM,BLK,SWF-P12(T3)
17
DC61-10676A
1
CAP-TRAP
PP(TB53),-,SWF-P12
18
DC60-20014A
2
SCREW TAPPING
TH,-,2,D4,L12,ZPC2,-
19
DC61-60497A
1
CLAMP-HOSE
HSWR,SWF-P12,ID70/OD75.8(TUB)
20
DC62-10304A
1
HOSE-FILTER TUB
EPDM,ID65,BLK,L151,SWF-P12/OD7
21
DC65-60118F
1
BAND RING
PW1,YEL,-,PI/33
22
DC66-10176B
1
PULLEY
ALDC,-,D297,P1291,ID12.5
24
DC60-60049A
1
WASHER-SPRING
-,ID10.5,OD18,T2.5,-,SIR
25
DC60-50014A
1
NUT-HEX
HEXAGON,M(12),ZPC2(YEL),SM10C,
26
DC66-10139A
1
BELT-TRANSMISSION
-,-,-,-,-
27
DC31-10181A
1
MOTOR-DRUM
MCC 52/64 148/SEC1,220~240V,50HZ,52MM
See on page11
27-1 DC31-00002C
1
MOTOR-DRUM
MCC 45/64 148/SEC1,220~240V,50HZ,45MM
See on page11
28
DC61-00041A
2
CUSHION-MOTOR
BUTYL,SWF-6V,ID16/OD20
29
DC60-40138A
1
BOLT-W.MOTOR
SM10C,HEX,M8,L62,-,ZPC2(YEL),-,-
SAMSUNG ELECTRONICS CO., LTD
NSA Remark
21
12. Expolded View and Parts List
12
11
1
2
19
25
18
23
21
13
3
14
22
4
27
20
24
26
9
15
28
16
30
17
6
10
5
7
35
36
32
37
33
41
34
39
40
38
22
SAMSUNG ELECTRONICS CO., LTD
12. Expolded View and Parts List
NO Code No
Q'ty Description
Specification
1
1-1
1-2
2
2-1
3
4
5
6
7
9
10
11
12
12-1
13
13-1
14
15
16
16-1
17
18
19
20
21
21-1
22
23
24
25
26
27
28
30
32
33
34
35
36
37
38
39
40
40-1
40-2
41
1
1
1
1
1
2
1
1
1
1
2
1
2
1
1
1
1
6
1
1
1
1
1
3
2
1
1
6
0.23
2
1
1
1
5
1
1
1
4
2
2
1
1
1
1
1
1
2
P1291/1191/1091/8091,COLD+HOT
P1291/1191/1091/8091,COLD-ONLY
P6091,COLD-ONLY
P1291/1191/1091(SUB),HIGH-RPM
P8091/P6091,(SUB),LOW-RPM
TH,+,2,D5,20,ZPC3,COVER-TOP
EGI,NTR,SWF-P12
DN-S14,TERMINAL-TYPE(DC5V)
SK5,-,YEL
EPDM,ID13.5,BLK,-,SWF-P12/OD17
-,-,2S,D3,L8,FZY,TH,+,1,D4,L12,FE FZY,FLANGE,PH,+,D4,L12,ZnFe(YEL),SWF-P12, WOOD TYPE
STEEL TYPE
EGI,WHT,SWF-P12
EGI,WHT,P6091
TH,+,1,D4,L12,FE FZY,FH,-,1,D4,L12,NTR,230V/50HZ,GRY,250V(16A)
P6091
PE,L335,SWF-P12(ORG)
HSWR,OD24,-,-,-,-,P1291,LEFT(RED/SPRAY)
NYLON#6,SEW-720DR,NTR
HSWR,OD30,-,-,-,-,P1291,RIGHT(NO-PAINT)
NYLON#6,SWF-P12,EATON(COLD)
NYLON#6,SWF-P12,EATON(COLD+HOT)
SK5,-,YEL
SOFT-PVC,ID10,NTR,L350,TH,+,M4,L10,NTR/WHT,STS304
FA-2151TS-1,250V,15A,2200PF,P1291,-25/+85'C
PH,TORX,1,D4,L12,ZPC2,P1291~P6091,250V/16A(PV)
NYLON66,-,DAWH-3NB,NTR(PI15)
SWF-P12V,PP(BB110)2200
PW1,YEL,-,PI/33
SBHG1-A,WHT,P1291(COLD)
SWF-P12,-,SWF-P12,80N
M10,-,-,SCP
PP(BJ-730),WHT,SWF-P12
PP(TB53),WHT,SWF-P12
EPDM,ID5.5,BLK,L220,OD9.5
P1291/P1091, 220V~240V/50Hz
P8091/P6091, 220V~240V/50Hz
220V~240V/60Hz
TN,+,2S,M4,L14,NTR,STS304
DC96-00070A
DC96-00070B
DC96-00052B
DC96-00053A
DC96-00053B
DC60-20136A
DC61-30344A
DC32-30006P
DC61-60063B
DC62-10311A
DC60-20050C
DC60-20054C
DC60-30015B
DC91-12083A
DC97-00218A
DC61-30345A
DC61-00056A
DC60-20054C
DC60-20030A
DC61-00115A
DC61-00122A
DC66-30160A
DC61-70216B
DC61-60180A
DC61-70217B
DC62-30313A
DC62-30314A
DC61-60063B
DC62-10068A
6001-000947
DC29-00002A
DC60-20138A
DC96-00146A
DC61-40086A
DC97-00139B
DC65-60118F
DC61-30342C
DC91-12292A
DC66-60149A
DC60-40026A
DC61-10672A
DC61-10673A
DC62-10302A
DC90-11110K
DC90-00149A
DC90-00035J
6002-000444
ASSY-M.WIRE HARNESS
ASSY-M.WIRE HARNESS
ASSY-M.WIRE HARNESS
ASSY-WIRE HARNESS
ASSY-WIRE HARNESS
SCREW TAPPING
FRAME-PLATE(U)
SENSOR PRESSURE
CLAMP-HOSE
HOSE-PRESSURE
SCREW TAPPING
SCREW TAPPING
SCREW-SPECIAL
ASSY-COVER TOP
ASSY-COVER TOP
FRAME-FRONT
FRAME-FRONT
SCREW TAPPING
SCREW TAPPING
DOOR-LOCK S/W
DOOR-LOCK S/W
LEVER
SPRING-HANGER
SLEEVE-PLUG
SPRING-HANGER
VALVE-WATER
VALVE-WATER
CLAMP-HOSE
HOSE-DRAWER
SCREW-MACHINE
FILTER-EMI
SCREW TAPPING
ASSY-POWER CORD
HOLDER-WIRE
ASSY-HOSE DRAIN(O)
BAND RING
FRAME
ASSY-LEG
DAMPER-SHOCK
BOLT-HEX
COVER-FRONT(L)
CAP-DRAIN
HOSE-DRAIN
ASSY-PUMP DRAIN
ASSY-PUMP DRAIN
ASSY-PUMP DRAIN
SCREW-TAPPING
SAMSUNG ELECTRONICS CO., LTD
NSA Remark
See on page11
See on page11
23
12. Expolded View and Parts List
11
1
5
6
2
7
3
7
4
9
10
NO
Code No
1
DC64-20013A
1
DECORATION-LID
ABS,SIL/COATING,SWF-P12,-
2
DC61-10682A
1
COVER-DOOR
ABS,WHT,SWF-P12
2-1
DC61-00055A
1
COVER-DOOR
ABS,WHT,P6091
3
DC61-00013A
1
DOOR-GLASS
GLASS,NTR,SWF-P12
4
DC61-40346A
1
HOLDER-GLASS
ABS,WHT,SWF-P12,-
4-1
DC61-00057A
1
HOLDER-GLASS
ABS,WHT,P6091
5
DC60-20060A
16
SCREW TAPPING
TH,+,2,D4,L8,FE,FZY
6
DC97-00100A
1
ASSY-HINGE
SWF-P12,NI+CR
7
DC60-10019B
4
SCREW MACHINE
RH,+,M5,L12,STS430,SEAL-LOCK
9
DC66-30161A
1
LEVER-DOOR
ZnDC,L40,SWF-P12
9-1
DC66-00016A
1
LEVER-DOOR
P6091
10
DC60-20140B
2
SCREW TAPPING
FH,+,1,D4,L20,STS304,-,-,-
11
DD60-50018A
2
NUT-FLANGE
-,M5XP0.8,FZY,MSWR10,-
24
Q'ty
Description
Specification
NSA
Remark
SAMSUNG ELECTRONICS CO., LTD
12. Expolded View and Parts List
17
18
14
6
4
5
13
8
3
2
NO Code No
Q'ty
Description
Specification
2
DC97-00004G
1
ASSY-PANEL FRONT
SWV-1200F,-
3
DC61-30348A
1
BODY-DRAWER
PP,WHT,SWF-P12
4
DC61-60498A
1
GUIDE-LIQUID
ABS,SWF-P12,-
5
DC61-10687A
1
CAP-RINSE
PP,WHT,SWF-P12
6
DC97-00003M
1
ASSY-PANEL CONTROL
P1291/P1191/P1091,ENG
8
6002-000445
2
SCREW-TAPPING
TH,+,2S,M4,L18,NTR,STS304
13
DC96-00132A
1
ASSY-PCB URETHAN
P1291,220/240V50/60HZ
13-1
DC96-00133A
1
ASSY-PCB URETHAN
P1191,220/240V50/60HZ
13-2
DC96-00134A
1
ASSY-PCB URETHAN
P1091,220/240V50/60HZ
13-3
DC96-00135A
1
ASSY-PCB URETHAN
P8091,220/240V50/60HZ
13-3
DC96-00136A
1
ASSY-PCB URETHAN
P6091,220/240V50/60HZ
14
6002-000554
3
SCREW-TAPPING
PH,2-4*12
17
DC91-12084A
1
ASSY-HOUSING D.W(U)
SWF-P12,-
18
DC61-10679A
1
HOUSING-DRAWER(L)
PP,WHT,SWF-P12
SAMSUNG ELECTRONICS CO., LTD
NSA
Remark
25