Craftsman 315.267380 Operator`s manual

Operator's Manual
iPRO
FESSiO
HAL
i
PROFESSIONAL
1/2 in., 14.4 VOLTS CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
315.267380
Save this manual for
future reference
• Safety
• Features
• Assembly
• Operation
•, Maintenance
• Parts List
CAUTION:
Read and
follow all Safety Rules and
Operating Instructionsbefore
first use of this product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
983000-186
04-03
Estates,
IL 60179
USA
0( us
•
Warranty .........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
3
•
General Safety Rules .................................................................................................................................................
3-4
•
Specific Safety Rules .................................................................................................................................................
4-5
•
Symbols ..........................................................................................................................................................................
6
•
Product Specifications ....................................................................................................................................................
7
•
Features .....................................................................................................................................................................
•
Assembly ..................................................................................................................................................................
•
Operation ................................................................................................................................................................
•
Maintenance .................................................................................................................................................................
16
•
Accessories
16
•
Exploded View and Repair Parts List ...........................................................................................................................
17
•
Parts Ordering / Service ...............................................................................................................................................
18
7-8
9-10
11-15
..................................................................................................................................................................
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
PROFESSIONAL
CORDLESS DRILL-DRIVER
If this rRAFTSMAN Professional Cordless Drill-Driver fails due to a defect in material or workmanship within one year
from the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE OR
SEARS SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
,_
_k
Look for this symbol to point out important safety precautions.
attention!!! Your safety is involved.
It means
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
2
Yourdrill-driverhasmanyfeaturesformakingyourdrilling
operations
morepleasantandenjoyable.Safety,
performance
anddependability
havebeengiventop
priorityinthedesignofthisdrill-drivermakingiteasyto
maintainandoperate.
_.
_k
Work Area
Personal Safety
•
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
•
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
•
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
•
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal
WARNING: Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE
•
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.
Electrical
•
•
•
INSTRUCTIONS
Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
Immediately. Damaged cords may create a fire.
CAUTION: Carefully read through this entire
operator's manual before using your new drill-driver.
Pay close attention to the Specific Safety Rules /
Symbols, Warnings and Cautions. If you use your
drill-driver properly and only for its intended use, you
will enjoy years of safe, reliable service.
injury.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
BATTERY PACK
CHARGER
Item No. 1315107
Item No. _ 11040
or item No. 9 11033 (981403001)
(981399-001)
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
3
•
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables
better control of the tool in unexpected situations. Do
not use on a ladder or unstable support.
•
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Tool Use and Care
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
•
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
•
Do not force tool. Use the correct tool for your
application. The correct toot will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is
dangerous and must be repaired.
•
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
•
Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may create a risk of injury
when used on another tool.
•
•
•
•
Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce riskof starting the tool
accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
Service
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
fire or heat. This will reduce the risk of explosion and
possible injury.
Rules For Safe Operation
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
II
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting in loss of power and overheating,
Important
Rules for Battery
Tools
•
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changIng accessories. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not place battery tools or their batteries near
•
Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pilot
light. To reduce the risk of serious personal injury,
never use any cordless product in the presence of
open flame. An exploded battery can propel debris
and chemicals. If exposed, flush with water immediately.
•
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
•
For best results, your battery tool should be
charged In a location where the temperature is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
Immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
4
•
Neverusea batterythat hasbeendroppedor
receiveda sharpblow. A damaged battery is subject
to explosion. Properly dispose of a dropped battery
immediately. Failure to heed this warning can result in
serious personal injury.
•
Save these instructions. This manual contains
important safety and operating instructions for
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
To reduce risk of injury, charge only nickelcadmium type rechargeable batteries. Other types
of batteries may burst causing personal injury and
damage. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
•
•
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Use of an attachment not recommended or sold
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Make sure cord is located so that it will not be
b. That extension cord is properly wired and in
good electrical condition; and
Cord Size (AWG)
16
16
16
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
•
To reduce the risk of electric shockl unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
RISK OF ELECTRIC SHOCK. DO NOT TOUCH
UNINSULATED PORTION OF OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
100'
•
_WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemicallytreated lumber.
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
50'
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
Cord Length (Feet) 25'
•
•
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
•
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
injury.
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
•
Note: AWG = American Wire Gage
SAVE THESEINSTRUCTIONS
5
Important:Some
interpretation
of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Time
Alternating Current
Type or a characteristic of current
Direct Current
Type or a characteristic of current
no
No Load Speed
Rotational speed, at no load
]
Class II Construction
Designates double-insulated
tools
construction
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes, surface speed,
orbits etc. per minute
,_
Safety Alert
Indicates danger, warning or caution.
It means attention!!! Your safety is involved.
Wet Conditions Alert
Do not expose to rain or use in damp
locations.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
Symbol
A
A
A
NOTE:
Meaning
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING:
injury.
Indicates a potentially hazardous situation which, if not avoided, could result in serious
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
Advises you of information or instructions vital to the operation or maintenance of the equipment.
6
PRODUCT
DRILL-DRIVER
SPECIFICATIONS:
315.267380
CHARGER
Item No. 9 11040
(981399-001)
120 V, 60 Hz, AC only
9.6 - 24 Volt
t Hour
Chuck
1/2 in. Keyless
Motor
Gear Train
DC Motor 14.4 Volt
Input
Charging Voltage
Switch
Two Speed
Variable Speed
Charge Rate
No Load Speed
0-350/min.
Clutch
0-1200/rain. (High)
24 Positions
Maximum Torque
320 in.lb.
KNOW YOUR
(Low)
DRILL-DRIVER
See Figure 1.
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
,_,
,_
WARNING: Carefully read through this entire
operator's manual before using your new drill-driver.
Pay close attention to the Rules For Safe Operation,
Warnings and Cautions. If you use your drill-driver
properly and only for what it is intended, you will enjoy
years of safe, reliable service.
BATTERY
PACK
Item 1315107
OR Item No, _911033
(981403-001
SWITCH
)
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
VARIABLE
SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression,
"PNO SPEED
GEAR TRAIN
Your drill-driver has a two speed gear train designed for
drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed,
WARNING: Do not allow familiarity with your drilldriver to make you careless. Remember that a careless fraction of a second is sufficient to inflictsevere
FORWARD/REVERSE
injury.
Your drill-driver has a forward/reverse selector located
KEYLESS
CHUCK
Your drill-driverhas a keyless chuck that allows you to hand
tighten or release drill bit in the chuck jaws.
SWITCH
To turn your drill-driver ON, depress the switch trigger.
Release switch trigger to turn your drill-driver OFF.
(DIRECTION
SELECTOR
OF ROTATION SELECTOR)
above the switch trigger.
WRIST
STRAP
A wrist strap is provided to reduce the chances of dropping
your drill-driver. Place one hand through the wrist strap
when carrying tool.
_,
WARNING: If any parts are missing, do not operate
your drill-driver untilthe missing parts are replaced.
Failure to do so could result in possibleserious
personal injury.
YELLOWLIGHT"ON" ANDRED
LIGHTFLASHINGINDICATES
DEFECTIVEBATTERYPACK
TORQUE
ADJUSTMENTRING
CHARGER
) SPEED
GEARTRAIN(HI-LO)
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
KEYLESS
CHUCK
GREENLIGHT"ON" INDICATESFULLY
CHARGEDANDSLOWCHARGING
TO MAINTAINBATTERYPACK
REDLIGHT"ON" INDICATES
FASTCHARGINGMODE
SCREWDRIVERBITS
BATI'ERYPACK
WRISTSTRAP
Fig. 1
CHARGER
See Figure 2.
Your charger has a "key hole" hanging feature for convenient, space saving storage. Screws should be installed so that
center distances are 4-1/8 inches apart.
CHARGER
BATTERYPACKSHOWN
IN CHARGER
BACKSIDE OF CHARGER
Fig. 2
8
AUTO-SPINDLELOCK
,_WARNING:
Make sure to insert drill bit straight into
chuck jaws. Do not insert drill bit into chuck jaws at
an angle and then tighten, as shown in Figure 4. This
could cause drill bit to be thrown from drill, resulting in
possible serious personal injury or damage to the
chuck.
Your cordless drill has an auto-spindle lock. This feature
makes installing and removing bits much easier. When the
switch trigger is released and the motor comes to a
complete stop, you may hear a click. The click you hear
indicates the auto-spindle lock has engaged and locked
the spindle. With the spindle locked, you can easily install
or remove bits by turning the chuck sleeve with one hand.
The auto-spindle lock disengages when the motor starts
again.
UNLOCK
DRILLBIT
CHUCKJAWS
Fig. 4
LOCK
REMOVING
CHUCKSLEEVE
RIGHT
INSTALLING
/
See Figure 3.
Fig. 3
•
BITS
See Figure 3.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Insert drill bit straight into chuck the full length of the
jaws as shown in Figure 3,
•
Tighten the chuck jaws on drill bit. To tighten, grasp
and hold the drill with one hand, while rotating the
chuck sleeve with your other hand,
Note: Rotate the chuck sleeve in the direction of the
arrow marked LOCK to tighten chuck jaws.
•
BITS
Do not use a wrench to tighten or loosen the chuck
jaws.
9
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Loosen the chuck jaws from drill bit.
•
To loosen, grasp and hold the drill with one hand,
while rotating chuck sleeve with your other hand.
Note: Rotate chuck sleeve in the direction of the arrow
marked UNLOCK to loosen the chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
TO A'I-rACH BAI-I'ERY PACK TO DRILL
TO REMOVE
See Figure 6.
See Figure 5.
Note: Battery pack is shipped in a low charge condition.
Therefore, it must be charged prior to use. Refer to page 11,
"CHARGING BATrERY PACK" for charging instructions.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Align raised ribs on battery pack with grooves on
bottom of drill, then attach battery pack to drill as
shown in Figure 6.
•
Make sure latch on battery pack snaps into place and
battery pack is secured to drill before beginning
operation.
BA'I-FERY
PACK FROM DRILL
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Depress latch located on front of battery pack (1) to
release battery pack.
•
Pull forward on battery pack (2) to remove from drill.
DEPRESSLATCHTO
RELEASEBATTERYPACK
RAISEDRIBS
LATCH
FORWARD
TO REMOVE
GROOVES
BATTERYPACK
BATTERYPACK
Fig. 5
CAUTION: When attaching battery pack to your
drill, be sure raised ribs and grooves align properly
and latch snaps into place properly. Improper
assembly can cause damage to drill and battery
pack.
10
Fig. 6
,_.
If after one hour red light is still flashing, this indicates a
defective battery pack and should be replaced.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
CHARGING
BA'n'ERY
Green light on indicates battery pack is fully charged
and slow charging to maintain battery pack.
Yellow light on and red light flashing indicates defective
battery pack. Return battery pack to your nearest Sears
Repair Center for checking or replacing.
PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until light on front of charger changes
from red to green.
•
When your battery pack becomes fully charged, the red light
will tum OFF and the green light will tum ON.
•
After normal usage, 1 hour of charging time is required to be
fully charged. A minimum charge time of 1-1/2 hours is
required to recharge a completely discharged tool.
•
The battery pack will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
TO CHARGE
•
Charge battery pack only with the charger provided.
•
•
Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
•
•
Connect charger to power supply.
•
Attach battery pack to charger by aligning raised ribs
on battery pack with grooves in charger, then slide
battery back onto charger. See Figure 7.
When the batteries become fully charged, unplug your
charger from power supply and remove the battery
pack.
LED FUNCTION
LED WILL BE LIGHTED TO INDICATE STATUS OF
CHARGER AND BA'n'ERY PACK:
BATTERY
TO
REMOVE
CHARGER
•
•
Red LED Lighted = Fast Charging Mode.
•
Green LED Lighted = Fully Charged And Slow
Charging To Maintain Battery Pack.
•
Red LED Flashing = Hot Or Deeply Discharged
Battery Pack. Also Defective Battery Pack After 1
Hour.
•
Yellow LED Lighted and Red LED Flashing =
Defective Battery Pack.
IMPORTANT
INFORMATION
HOT BA'n'ERIES
TO
ATTACH
GROOVES
OF CHARGER
FOR
RECHARGING
Under extreme continuous use, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your
battery charger to flash. When battery pack cools down,
red light will glow continuously indicating fast charging
mode, 1 hour charge time. Once the battery pack cools
down, it will recharge battery pack in fast charging mode
as normal.
Fig. 7
Red light should turn on. Red light indicates fast
charging mode.
Note: This situation only occurs when extreme continuous
use of your drill causes the batteries to become hot, It
does not occur under normal circumstances. Refer to
If red light is flashing, this indicates battery pack is
deeply discharged or hot.
If battery pack is hot, red light should become steady
after battery pack has cooled down.
"CHARGING BA'n'ERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears repair center for
electrical check.
If battery pack is deeply discharged, red light should
become steady after voltage has increased, normally
within 60 minutes.
11
SWITCH
SWITCH
See Figure 8.
See Figure 10.
LOCK
TO turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector in center position.
SELECTORWITH
REVERSE
CENTERLOCK POSITION
SWITCHTRIGGER
VARIABLE
f
Fig. 8
SPEED
FORWARD
Fig. 10
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression,
_
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
REVERSIBLE
TWO SPEED
See Figure 10.
GEAR TRAIN
See Figure 9.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
Your drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of your drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
TWO SPEED
GEAR TRAIN(HI-LO)
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
_k
LO
SPEED
CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation or the two speed gear train
(hi-lo).
To stop, release switch trigger and allow the chuck to
come to a complete stop.
SPEED
Fig. 9
12
KEYLESS
ADJUSTABLE
CHUCK
See Figure 11.
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and
the size of screw you are using.
A keyless chuck has been provided with your drill to allow
for easy installation and removat of bits. As the name
implies, you can hand tighten or release drill bits in the
chuck jaws. Arrows on the chuck indicate which direction
to rotate the chuck sleeve in order to LOCK (tighten) or
UNLOCK (release) the chuck jaws. Loosen the chuck
sleeve by rotating it counterclockwise with one hand.
Insert drill bit straight into the chuck the full length of the
jaws, and tighten securely by rotating the chuck sleeve in
clockwise direction.
TO ADJUST
UNLOCK
(Release)
TORQUE
•
Identify the twenty four torque indicator settings
located on the front of your drill. See Figure 12.
•
Rotate adjusting ring to the desired setting.
1 -
4
For driving small screws.
5 -
8
For driving screws into soft
material.
9 - 12
DRILLBIT
For driving screws into soft and
hard materials.
• 13 - 16
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 21 --_11
For heavy drilling.
Note: Remember the two-speed feature (HI-LO) when
setting torque. The amount of torque will vary depending
on which speed setting you have your drill-driver. Switching to LO speed will increase torque. Switching to HI
speed will decrease torque,
CHUCKJAWS
LOCK
(Tighten)
CHUCKSLEEVE
,_
TORQUE
ADJUSTINGRING
TO DECREASE
TORQUE
/
Fig. 11
WARNING:
Do not hold chuck sleeve with one hand
and use power of the drill to tighten chuck jaws on
drill bit. Chuck sleeve could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
TOINCREASE
TORQUE
Fig. 12
13
,_
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
with clamps to keep it from turning as the drill bit rotates.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
APPLICATIONS
(Use drill-driver only for the purpose listed below)
•
Drilling in wood.
•
Drilling in ceramics, plastics, fiberglass, and laminates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
•
•
Drilling in both hard and soft metals.
Using driving accessories, such as driving screws with
screwdriver bits.
•
Mixing paints.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
,_
DRILLING
See Figure 13.
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
I
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
I
J
Fig. 13
14
CHUCK
Insert hex key in chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It
can now be unscrewed by hand. See Figure 16.
REMOVAL
See Figures 14, 15, and 16.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Insert a 5/16 inch or larger hex key into the chuck of
your drilland tighten the chuck jaws securely.
•
Tap the hex key sharply with a mallet in a clockwise
direction, See Figure 14. This will loosen the screw in
the chuck for easy removal.
MALLET
CHUCKJAWS
Fig. 16
TO RETIGHTEN
HEXKEY
A LOOSE
CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
KEYLESS
CHUCK
To tighten, follow these steps:
Fig. 14
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
Figure 15.
Note: The screw has left hand threads.
SCREWDRIVER
Fig. 15
15
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Ftgure 10.
•
Open the chuck jaws.
•
Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key h sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
•
Open the chuck jaws and remove hex key.
•
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
,_
Do not abuse power tools. Abusive practices can
WARNING:
When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product damage.
damage tool as well as workpiece.
Only the parts shown on parts list, page 17, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
,_
,_
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
BATTERIES
The battery pack for your drill-driver is equipped with
nickel-cadmium rechargeable batteries. Length of service
from each charging will depend on the type of work you
are doing.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
•
Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
•
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
BAI-FERY PACK
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries properly.
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
A
Consult your local waste authority for information
regarding available recycling and/or disposal options.
The following
recommended
accessories
are currently
REMOVAL
AND PREPARATION
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
available
at Sears
Retail Stores.
•
6-Pc. Extra Length Magnite Power Bit Set
•
High Speed Bits ...... 1/2 in. Max.
•
30-Pc. Power Screwdriver/Nutdriver
Set and Case
•
Wood Boring Bits......1-1/2
•
17-Pc. Power Screwdriver/Nutdriver
Set and Case
_
WARNING"
The use of attachments or accessories
not listed might be hazardous.
16
in. Max.
CRAFTSMAN
I
1/2 in. PROFESSIONAL
CORDLESS
MODEL NO. 315,267380
DRILL-DRIVER
The model number will be found on a plate attached to the motor housing. Always mention the model number
in all correspondence regarding your CRAFTSMAN 1/2 in, PROFESSIONAL CORDLESS DRILL-DRIVER
or when ordering repair parts.
SEE BACK
PAGE FOR PARTS
ORDERING
INSTRUCTIONS
2
5
PARTS
Key
No.
Part
Number
Description
LIST
Qty.
1
975379-000
Screw (Special) ....................................................................................
1
2
981503-001
Chuck (Item No. 6903321) ...................................................................
1
3
981501-001
Logo Plate ................................................................................
4
* Item No. 1315107
5
* Item No. 9 11040
,............ 1
Battery Pack (981403-001) ..................................................................
1
Charger (981399-001) ..........................................................................
1
Carrying Case - Not Shown .................................................................
Operator's Manual
1
or Item No. 9 11033
6
3051719
983000-186
* Can Be Purchased Thru RSOS (Retail Special Order System)
17
I
Your Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
® (1-800-469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
1-800-361-6665
Au Canada
s"
(1-888-784-6427)
(Canada)
pour service
1-800-LE-FOYER
en fran_ais:
Mc
(1-800-533-6937)
www.sears.ca
, EAR6
® Registered Trademark / TMTrademark / sMService Mark of Sears, Roebuck and Co.
® Mama Registrada / ¢MMarca de Fdbrica / SMMarca de Servicio de Sears, Roebuck and Co.
MC
Marque de commerce / MO Marque ddpos_e de Sears, Roebuck and Co.
© Sears, Roebuck and CO.