Craftsman 315.114420 Operator`s manual

Operator's Manual
3/8 in. 16.8 VOLT
CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
315.114420
Save this manual
future reference
,_
for
WARNING:
Toreducethe risk of injury, the
user must read and understand the operator's
manual before using this product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuc'k
and Co., 3333 Beverly
Rd., Hoffman
visit the Craftsman web page: www,sears,com/craftsrnan
983000
11-03
297
Estates,
IL 60179
USA
•
Warranty .......................................................................................................................................................................
•
General Safety Rules ............................................................................................................................................
3 4
•
Specific Safety
4 b
•
Symbols .........................................................................................................................................................................
6
•
Product. Specifications
7
•
Features
.....................................................................................................................................................................
•
Operation
..................................................................................................................................................................
•
Maintenance
.................................................................................................................................................................
t5
•
Accessories
..................................................................................................................................................................
i 5
•
Exploded
View and Repair Parts List ...........................................................................................................................
16
•
PaEs Ordering/Service
Rules
..............................................................................................................................................
....................................................................................................................................................
ON CRAFTSMAN
3/8 in, CORDLESS
If this rRRFI"$NRN 3/8 in. Cordless Drill-Driver
90 days from the date of purchase.
gives you specific
is used for commercial
18
within one year from the date of pu_CENTER IN THE UNITED STATES, and
or rental purposes,
this warranty
applies for only
legal rights, and you may also have other rights which vary from state to state.
aad Co., Dept. 817WA,
HoT|men Estates,
IL 60179
Your drill driver has many features for making your drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this drill-driver making it easy to
maintain and operate.
,_.
WARNING : Do not attempt to use this product until
you read thoroughly and understand completely the
operator's manual. Pay close attention to the safety
rules including Dangers, Warnings and Cautions. If
you use this product properly and only as intended,
you will enjoy years of safe, reliable service.
Look for this symbol to point out important
attention!!! Your safety is involved.
_k
9-14
DRILL-DRIVER
If this I:RRF'r$1_ AN 3/8 in, Cordless Drill-Driver fails to give complete satisfaction
chase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE
Sears will repair it, free of charge.
Sears, Roebuck
7-8
...............................................................................................................................................
FULL ONE YEAR WARRANTY
This warranty
2
safety
precautions.
It means
WARNING:
The operation of any power tool can result ir_foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
SMe[y Mask for use over eyeglasses or s[ar:dard safety giasses with side shields, available al Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
2
_k WARNING: Read and understand all instructions,
Failure to follow a)! instructions listed below, may
resu_ in eiectnc shock, fire and/or serious personal
injury.
SAVE THESE
Work
•
Do not operate power tools in e_plosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite l:he dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. DistraCtions can cause you
to lose control,
Electrical
•
•
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
riot use tool while tired or under the influence of
drugs, alcohol, or medication.
A moment of inattention while operating power tools may result in serious
personal injury,
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose c)othes,
iewetry, or long hair can be caught in moving parts.
•
Avoid accidental starling. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
•
Remove adjusting keys or wrenches before turning the tool on, A wrench or a key that is left attached
to a rotating part of the tool may result in persona)
injury,
•
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables
better control of the tool in unexpected situations, Do
not use on a ladder or unstable support.
•
Use safety equipment.Always
wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Area
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Safety
Do not abuse the cord. Never use the cord to carry
the charger. K_p cord away from heat, oil, sharp
edges, or moving parts, Replace damaged cords
Immediately. Damaged cords may create a fire
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery, A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery, Use battery
only with charger listed.
MODEL
315.114420
BATTERY PACK
iTEM NO. _91137(}
{t 323516 )
CHARGER
ITEM NO. _911041
(1425301 )
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
Safety
•
iNSTRUCTIONS
•
•
Personal
Tool Use and Care
•
Use clamps or other practical way to secure and
supped the workpiece to a stable platform. Holding the work by hand or against your body is unstable
and may lead to loss of control.
Do not force tool. Use the correct tool for your
application.
The correct tool will do the job better and
safer at the rate for which it is designed,
Do nor use tool ff switch does not turn it on or off.
A tool that cannot be controlled with the switch is
dangerous and must be repaired,
Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, shangir_ accessQ, iee, or storing the tool. Such
preventive safety measures reduce risk of starting the tool
scc_er_L_.
Store idle toots out of reach of children and other
untrained persons, Tools are dangerous in the hands
•
•
•
•
of Untrained
•
iis_i!n;,
•
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
•
Check for misalignment or binding of moving parts,
breakage of pads, arid any other condition that may
affect the toors operation. If damaged, have the tool
serviced before using. Many accidenls er_-;c_'u_s(÷(;
by
poody maintained tools.
Use only accessories
that are recommended by the
manufacturer
for your model. Accessories that may
be suitable for one tool, may create a risk of injury
when used on another tool.
•
Service
•
l
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that
can make a connection from onetermlnal to
another, Shorting the battery terminals together may
cause sparks, burns, or a fire,
"reel service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a dsk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or iniury.
Hold tool by insulated
gripping
surfaces when performing an operation where the cutting tool may contact
hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
•
•
For Safe
Make sure your extension cord is in good
condition. When using an extension cord, be sure
to use one heavy enough to carry the current your
product will draw. A wire gage size (A.W.G.) of at
least 16 is recommended for an extension cord 108
feet or less in length. A cord exceeding log feet is
not recommended. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the
cord. An undersized cord will cause a drop in line
voltage _sutting in loss of power and overheating.
Rules
for Battery
fire or heat. This will reduce the risk of explosion
possible injury.
Operadion
Know your power tool. Read operator's manual
carefully. Learn its applications
and limitations,
as welt as the specific potential hazards related to
this tool. Foilowing this rule will reduce the risk of
ele_ric shock, [inh or serious injury.
important
•
Rules
Tools
Battery tools do not have to be plugged Into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards when not using your battew tool or when
changing accessories. Following this rule will
reduce the nsk of electric shock, fire, or serious
personal iniu,'y
and
•
Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pitot
light. To reduce the risk of serious personal inlury,
never use any cordless product in the presenc_ of
open flame. An exploded battery can propel debris
and chemicals. If exposed, flush with water immedi
ately.
•
Do not charge battery tool in a damp orwet location. Following this rule will reduce the risk of electric
shock.
•
For best results, your battery tool should be
charged in a location where the temperature
is
more than 50°F but less than t00°F. Do not store
outside or in vehicles.
•
Under extreme usage or temperature
conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice or
vinegar. If liquid gets Into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule wilr
reduce the risk of serious personal iniury,
._WARNING
: Never use a battery that has been
dropped or received a sharp blow. A damaged battery
is subject to explosion. Properly dispose of a dropped
battery fmmediately. Failure to heed this warning can
result in serious personal mjury.
•
Do not operate charger if it has received e sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shook, tire. or
serious personal injury.
•
Do not disassemb|e charger; take it to a qual#ied
serviceman
when service or repair is required.
Incorrect reassembly may result in a risk o'f
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
_njury.
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
To reduce risk of injury, charge only nickelcadmium type rechargeable
batteries. Other types
of batteries may burst causing personal injury and
damage. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury,
•
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
Use of an attachment
not recommended
or sold
by the battew charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury,
•
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
etectdc shock, fire, or serious personal iniury.
•
RISK OF ELECTRIC SHOCK. DO NOT TOUCH
UNINSULATED
PORTION OF OUTPUT CONNEC=
1"OR OR UNINSULATED
BA'rI'ERY TERMINAL.
•
To reduce risk of damage to charger body and
cord, pub by charger plug rather than cord wher_
disconnecting
charger.
Following this rule will
reduce the risk of electric shock, fire, or serious
persona] injury.
•
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
•
An extension cord should not be used unless
absolutely necessary.
Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
•
That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
*
That extension
good electrical
cord is properly
cendition; and
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool, If you loan someone this tool, loan them
these instructions also. Following this rule wi!l
reduce the risk of electric shock, fire, or serious
personal injury.
,I_k_WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based
paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
wired and in
•
That wire size is large enough forAC ampere
rating of charger as epecified below:
Cord Length (Feet) 25'
50'
100'
Cord Size (AWG)
I6
Note: AWG = American
•
16
16
Wire Gage
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce the
risk of ele_ric shock, fire, or sedous personal injury.
5
important:Someofthefollowing
symbols
maybeusedonyourtool.Pleasestudythemandlearntheirmeaning.
Proper
irrterpretation
of these symbols will allow you to operate the tool better and safer,
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency
rain
Minutes
Time
Alternating
Current
(cycles per second)
Type or a characteristic
o; current
Direct Current
Type or a characteristic
of current
no
No Load Speed
Rotational
_,/rain
Revolutions
or Reciprocation
Per Minute.
speed, at no load
Revolutions, strokes,
surface speed, orbits etc. per minute
A
Safety Alert Symbol
Indicates danger, warningoroaution.
It means attentien!!i Your safety is
involved.
O
Wear Eye Protection
Always wear safety goggles or
safetyglasseswith
side shields when
operating this product
®
Wet C,onditions Alert
Do not expose to rain or use in damp
locations.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding,
The safety warnings do not by themselves
eliminate any danger, The instructions or warnings they give an_ not substitutes for proper accident prevention
measures.
Symbol
Meaning
DANGER:
Indicates an imminently
serious injury
hazardous
situation
,ik
WARNING
: Indicates
serious injury.
hazardous
situation which, if not avoided,
A
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
NOTE:
Advises you of information
a potentially
or instructions
which, if not avoided, will result in death or
vital to the operation or mai_enance
SAVE THESE INSTRUCTIONS
6
could _._st.fltin death or
of the equipment.
Chuck
Motor
GearTrain
Switch
NoLoad Speed
BAI-rERY
PACK
3/8 in. Keyless
DC Motor !6.8 Volt
Two Speed
Variable Speed
O 33g/rain (Low)
0 1200/min (High)
Item No. _11370
(1323516)
KNOW YOUR DRILL-DRIVER
See Figure 1.
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
KEYLESS
CHUCK
Your drill-d_er has a keyless chuck that allows you to hand
tighten or release ddll bit in the chuck jaws,
SWITCH
To turn your drill-driver ON, depress the switch trigger.
Release switch trigger to turn your drill-driver OFF,
SWITCH
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental staEing
when not in use.
VARIABLE
SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure, Speed is controlled
by the amount of switch trigger depression.
TWO SPEED GEAR TRAIN
Your drill-driver has a :wo speed gear train designed for
drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed.
M_imum Torque
CHARGER
Rating
Charging Voltage
Charge Rate
Ch_ch
350 in.lb,
Item No. 211041
(1425301)
120 V, 60 Hz,AC only
7,2 24 Volt
1 Hour
24 Positions
FORWARD/REVERSE
SELECTOR
(DIRECTION OF ROTATION SELECTOR)
Your drill-driver has a forward/reverse
selector located
above the switch trigger,
WRIST STRAP
A wrist strap is provided to reduce the chances of dropping
your drill driver. Place one hand through the wrist str_
when carrying tool.
E_IT STORAGE
When riot in use, bit(s) provided with your drill-driver can
be ptaced in the storage area located on the bot[om of the
rno_or housing.
L|_.VEL
To keep drill bit level during drilling operations, a level is
located on the back of the motor housing.
_,
WARNING:
If any parts are missing, do not operal:e
your drill-driver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
TWO-SPEED
GEAR TRAIN(HI-LO)
LEVEL
TORQUE
KEVLESS
CHUCK
RING
__
DIRECTION
OF
ROTATION
SELECTOR
(FORWARD/REV
ERSE)
LEVEL
REAR VIEW
BIT
STORAGE
TRIGGER
SCREWD_VER
BATTERYPACK
/
SHOWN_
BATTERY PACK
1
SHOWNIN CHARGER
K
WRIST STRAP
_I/2in,
CHARGER
RED LED ON INDICATES
GREENLED ON AFTER FASTCHARGING
CYCLE,INDICATESFULLY CHARGEDBATTERY
PACKAND IN TRICKLE CHARGE MODE
Y ELLOWANDGREEN LEDSON INDICATESDEEPLY
DISCHARGEDOR DEFECTIVEBATI'ERY PACK.
Fig,
CHARGER
See Figure 1,
Your charger has a "key hole" hanging feature for c_nvenier_, spac_ saving storage. Screws should be installed so tha_
center dist;_nces _,re 4-1/2 inches apart.
8
,_
WARNING
: De no_ allow familiarity with your drill
driver to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
BATTERY
PACK
The battery pack for your iool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you shdutd charge i_until light on front of charger changes
from red to green,
Note; Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged,
CHARGING
BATTERY
•
•
•
•
•
•
•
•
•
•
OF
•
Red LED on - Fast charging mode.
•
Green LED on - Fully charged and in trickle charge
mode.
•
Green LED on = When battery pack is inse.tt,ed into
charger, indicates hot battery pack or thai ba:l:_ry pac_
is out of or below nomlal temperature range.
Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
•
•
No LED on = Defective charger or battery pack.
PACK
See Figure 1
•
•
LI;D FUNCTIONS
OF CHARGER
LE-D WILL BE ON TO INDICATE
STATUS
CHARGER
AND BATTERY
PACK
Charge battery pack only with the charger provided.
Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only,
Connect charger to power supply.
Place. battery pack in charger aligning raised rib on
battery, pack with groove in charger. See Figure 1.
Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
Normally, the red LED on ehargerwill come on, This
indicates charger is in fast charging mode.
Red LED shouid remain on for approximately
1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is in
tnckle charge mode. Note: Green LED will remain on
until battery pack is removed from charger or charger
is disconnected from power supply,
If both yellow and green LED come on, this indicates a
deeply discharged or defective battery pack.
Allow battery pack to remain in charger for 15 to 30
minutes, When battery pack reaches normal voltage
range, red LED should come on.
If red LED does not come on after 30 minutes, this
indica_.es a defective battery pack and should be
replace,&
After normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack,
The batten! pack will became slightly warm to the
touch while charging, 'This is normal and does not
indicate a problem,
Do not place ci]arger and battery pack in an area of
extreme heat or cold. It will work best at normal room
temperature,
Note: Charger and battery pack should be placed in a
location where the temperature is more than 50°F but
less than 100°F.
When batteries become fully charged, unplug charger
from power supply and remove the battery pack,
_.
CAUTION:
To prevent damage to battery pack,
remove battery pack from charger immediately if no
LED comes on, Return battery pack and charger to
your nearest Sears Service Center for checking or
replacing. Also, if you are rernoving battery pack from
charger and no LEDs are on, return both battery pack
and charger to your nearest Sears Service Center.
Do not insert another battery pack into charger. A
damaged charger may damage a battery pack.
IIVIPORTANT INFORMATION
HOT BATTERY PACK
FOR RECHARGING
When using your drill-driver continuously, the battenes in
your battery pack will becorrre hot. You should ieta hot
battery pack cool down for approximately
30 mim,_es
before attempting to recharge. When the battery pack
becomes discharged and is hot. this will cause the green
LED to come on instead of the red LED. After 30 minutes,
reinsert battery pack in charger. If green LED co_inues to
remain on, return battery pack to your nearest Sears
Repair Center for checking or replacing,
Note: This situation only occurs when continuous use ol
your drill causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
BATTERY PACK" for normal recharging of battenes. If
the charger does not charge your battery pack under
normal circumstances,
return both the battery pack and
charger to your nearest Sears Repair Center for elactdcai
check.
IIVlPORTANT INFORMATION
COOL BATTERY PACK
FOR RECHARGING
if battery pack is below normal temperature range, the
green LED an charger will come on. Allow battery pack to
reach normal temperature, then the red LED will come on,
Note: Refer to "CHARGING
BA'n-ERY PACK" for
normal recharging of batteries. If the charger does not
charge your battery pack under normal circumstances,
re_:urnboth the battery pack and charger to your nearest
Seam Repair Center for electrical check,
SWITCH
SeeFigure2.
ToturnyourdnllON,depress
theswitchtrigger.Toturnit
TO INSTALL
•
Lock switch trigger on your drill by placing the direction
of rotation selector in center position, See Figure 5.
OFF, relea'_;e the swilch trigger.
•
Place battery pack in your drill, Align raised rib on
battery pack with groove inside drill See Figure 4
FORWARD!REVERSE
SELECTOR
VARIABLE SPEED
SWITCHTRIGGER
VARIABLE
BATTERY
PACK
BATTERY PACK
Fig. 2
SPEED
LATCHES
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure, Speed is
controlled by the amount of switch trigger depression.
Note: You mlgn_ hea,- a whistling or ringing noise from tile
switch during use, Do not be concerned, this is a normal
part of the switch function.
TWO-SPEED
GEAR
TRAIN
See Figure 3.
Your drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds, A slide switch is
located on top of your drill to select either DO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque,
When using drill in the Hi (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (!) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
TWO SPEED
GEAR TRAIN (HI-LO)
DEPRESSLATCHESTO
RELEASE BA'n"ERYPACK
•
Make surethe latches on each side of your battery
pack snap in place and battery pack is secured in ddll
before beginning operation.
_
CAUTION:
When placing battery pack in your drill,
be sure raised rib on bakery pack aligns with groove
inside drill and latches snap into place properly.
Improper assembly of battery pack can cause
damage to internal components.
LO
SPEED
TO REMOVE
•
HI
SPEED
•
•
Fig. 3
!0
Fig, 4
BATTERY
PACK
Lock switch trigger on your drill by placing the direction
of rotation sele_or in _nt,er position. See Figure 5,
Locate latches on sicJe of bakery pack and depress; to
release battery pack from your drill. See Figure 4.
Remove battery pack from your drill.
SWITCHLOCK
SeeFigure5.
TheswitchtriggercanbelockedintheOFFposition.
This
featureconbeusedtoprevent
thepossibility
ofaccidental
staEing when not in use. To lock switch trigger, place the
direction of rotation seh;ctor (Forward/Reverse
Selector)
in center position
KJ=YLESS
CHUCK
See Figure 6.
Your drill has a keyless chuck. As the name implies, you can
hand tighten or release dnll bits in the chuck iaws. Grasp and
hold the cellar of the chuck with one hand. Rotate the c_huck
body with your other hand. The arrows on the! chuck
indi_-qte which direction to rotate the chuck body in oraer to
LOCK (tighten) or UNLOCK (release) the dnfl bit
REVERSE
DRILL BIT
UNLOCK
(RELEASE)
CHUCK
COLLAR
CHUCKJAWS
FORWARD
TRIGGER
LOCK
(TIGHTEN)
Fig. 5
._1 WARN1NG:
8arrery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carryir]g at your side.
,_,
REVERSIBLE
See Figure 5.
This tool has the feature of being reversible. The direction
o'f rotation is controlled by a selector located above the
switch trigger. With the ddll held in normal operating
position, the direction of rotation selector should be
positioned le the lef: of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When tt_e selector is in center position, the
switch trigger is locked.
,_
CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direc'rion of rotation
To stop, release switch trigger and allow the chuck to come
to a complete stop
11
CHUCK
BODY
Fig 5
WARNING:
Do not hold chuck body with one hand
and use power of the drill to tighten chuck jaws erl
drill bit. Chuck body could slip in your hand or your
hand could slip and come in contact with rotating drili
bit. This could cause an accident resulting in serious
personal injury.
INSTALLINGBITS
SeeFigure7,
RI-'MOVING
•
Lock the switch trigger by placing the direction of
rotation sel_cter ir_ c_-;nter position. See Figure 5.
•
Lock the switch trigger by placing the direction of
rotation selector in center position, See Figure 5.
•
Oper_ or close ct/iJck iaws to a point.; where the open
ing is slightly larger than the bit size you intend to use.
Also, E_ise the fronl: of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Loosen the chuck iaws from drill bit.
•
To loosen: grasp and hold the collar of the chuck w_th
one hand, while rotating chuck body wfth your other
hand, Note; Rotate shuck body in the direction of the
arrow marked UNLOCK to loosen chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws,
•
Remove drill bit from chuck jaws,
See Figure 7.
•
Insert drill bit straight into chuck the full length of the
iaws as shown in Figure 7,
•
Tighten the chuck jaws on drill bit.
DRILL BIT
BITS
UNLOCK
(RELEASE)
CHUCK
COLLAR
ADJUSTABLE
TO ADJUST
CHUCK
JAWS
CLUTCH
identify the twenty four torque indicator settings located
on the front of your dril!, See Figure 9.
•
Rotate adjusting ring to the desired setting,
• I - 4
For dnving small screws.
5
RIGHT
TORQUE
•
LOCK
(TIGHTEN)
CHUCK
BODY
•
8
9 - 12
• 13- 16
- 17
For driving large screws.
20
• 21 - _,¶
Note; Rotate the chuck body in the direction of the
arrow marked LOOK to tighten chuck jaws.
Do no(t use e wrench to tighten or loosen chuck jaws.
For driving screws into so_
material.
For driving screws into soft and hard
reaterials,
For driving screws in hard wood.
Fig, ?
To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
_k
TORQUE
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper seeing depends on the type of material and the
size of screw you are using.
For heavy drilling.
TO DECREASE
TORQUE
ADJUSTING
RING
WARNING:
Make sure to insert drill bit straight into
chuck jaws, Do not insert dnll bit into chuck jaws at
an angle then tighten, as shown in Figure 8. This
could cause drili bit to be thrown from drill, resulting
in possible serious personal injury or damage to the
chuck
TO INCREASE
TORQUE
Fig. 8
12
Fig. 9
BIT STORAGE
See Figure 10.
Di:_ILLING
$_,_ Figure 12.
When not it_ use, bits provided with your drill Can be
placed in the storage a,_a located on the bottom of your
drill as shown in Figure 10.
LEVEL
SCREWDRIVER
BiTS
\
,_
I IIC_:
__..__
WAFINING; Always wear safety gogg es or safety
glasses with side shields when operating tools.
Failure to do so could result in obiects being thrown
into your eyes, resulting in possible sedous injury.
Fig, 12
LEVEL
When drilling hard smooth surfaces use a ceEer punch to
mark desired hole location, This will prevent the dnii bi:
from slipping off center as the hole is started, However,
the low speed feature allows starting holes withoh': canter
gunching if desired, To accomplish this, simply eperale
your drill at a low speed until the hole is started.
"The material to be drilled should be secured in a vise or
wilh clamps to keep it from turning as the drill bit rotales.
See Figure 11,
A convenient feature provided with your drill is a level, it
is recessed in the motor housing on back of your drill. It
can be used to keep drill bit level during drilling opera
lions.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
prassure to keep the bit cutting. Do not forge or apply side
pressure to elongate a hole.
,_
WARNING:
Be prepared for binding or bit
breal_hreugh. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could Cause loss of control widen
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use ,'_ tight oil on the dtll/bit to keep
it lrom overheating, The oil will prolong the life of the bit
arid increase the drifting action.
If :he bit iares in workpiece or if the drill stalls, release
switch trigger immediately, Remove the bit from the
workpiece and determine the reason for jamming.
Fig. 11
13
CHUCKREMOVAL
See Figures
•
13, 1_t, and 15
[he chuck must be removed
accessories, Ta ramave:
in order to use some
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 5.
•
insert a 5/16 in. or larger hex key into the chuck of your
drill and tighten the chuck jaws securely.
•
Tap the hex key sharply with a mallet in a clockwise
direction See Figure 13, This will loosen the screw in
the chuck for easy removat.
Insert hex key in chuck and tighten chuck jaws sa
curely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle, Ii san
now be unscrewed by hand. See Figure 15,
MALLET
MALLET
CHUCKJAWS
Fig. i5
TO RETIGHTEN
HE)( KEY
KEYLESS
CHUCK
CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
Te tighten, follow these steps:
Fig, "_3
•
•
A LOOSE
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
Figure 14.
Note: The screw has left hand threads.
•
•
•
•
SCREWDRIVER
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 5.
Open the chuck jaws,
Insert he× key into chuck and tighten chuck jaws
securely, Tap hex key sharply with a mallet in a
clockwise direction. "This will tighten chuck on the
spindle,
Open the chuck jaws and remove hex key,
Tighten the chuck screw,
Note: The chuck screw has left hand threads.
Fig. 14
14
_1=WARNING:
D_) not abuse power tools. Abusive pracllcas
tool as well as workpieca,
When servicing, use only identical
Craftsman
replacement parts. Use of any other
part may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plasti_-_ are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remow) dirt, dust, oil, grease, etc.
can damage
Only the parts shown on parts list, page 16, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
_
WARNING:
Do not art.erupt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or' modifica_ior= i_:;
misuse and could result in a hazardous condition
leading to possible serious personal injury.
Your drill's battery pack is equipped with nickeFcedmium
rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing,
•
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventuaUywear
out. Do not disassemble battery pack
and a_tempt to replace the batteries. Handling of these
baEeries, especially when wearing rings and jewelry,
could resut" n a serious burn.
•
Store and charge your batteries in a cool area
Temperatures above or below normal room
temperature will shorten battery life.
Never store batteries in a discharged condition,
Recharge them immediately after they are
discharged,
_IL
WARNtNG:
Do not at any time let brake fluids,
gasoline, petroleum-based
products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that (.'an damage, weaken or destroy
plastic.
BATTERIES
To obtain the longest possible battery
following:
•
All batteries gradually lose their charge, The higher
the temperature the quicker they lose their charge. If
yOU store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life,
lifo, we suggest the
To preserve naturalresources, please
reoyc!e or dispose of batteries properly
BATTERY PACK REMOVAL
FOR RECYCLING
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
_.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
The following
recommended
accessories
are currently
AND PREPARATION
WARNING:
Upon removal, cover the battery pack's
m terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be n=.cycled or disposed of properly.
Also, never touch both terminals with metal obiects
and/or body parts as short circuit may result. Keep
away from children, Failure to comply with these
warnings could re.suit in fire and/or serious iniury.
available at Sears Retail Stores,
•
6-Pc, Extra Length MagnJte Power Bit Set
•
17-Pc. Power ScrewdriverlNutdriver
•
30-Pc, Power Screwdriver!Nutdriver
•
High Speed Bi_s (For Wood or Metal)..3/4
_1
WARNING:
Set and Case
The use of attachments or accessories not listed might be hazardous.
15
Set and Case
in. Max.
CRAFTSMAN
I
318 in., 16.8 VOLT CORDLESS
in ali correspondence
he model numberwill
repair paEs.
DRILL-DRIVER
- MODEL NO. 315.114420
regarding your 3/8 in., 16.8 VOLT CORDLESS DRILL-DRIVER
or when ordering
be found on a plate attached to the motor housing. Always mention the model number
SEE BACK PAGE FOR PARTS ORDERING
INSTRUCTIONS
2
4
3
PARTS LIST
Key
No.
Par[
Number
Description
i
6613401
Screw (Special) ......................................................................
1
2
6903304
Chuck .....................................................................................
1
Qty.
3
* Item No. 91 !370
Battery Pack (1323516) .........................................................
!
4
* Item No. 9 11041
Charger
1
5
(1425301) .................................................................
3064302
Carrying Case
983000-297
Operator's
Not Shown ..................................................
Manual
* Can Be Purchased Thru RSOS (Retail Special Order System)
16
1
l
17
Your Home
For repair-in
your home-of
all major brand appliances,
lawn and garden equipment,
or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
!iiili
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
_
(1-800-469-4663)
day or night(U.S.A,
www.sears.com
and Canada)
iii!i!_
www.sears.ca
r
i},
_¸_
,, ;i!
Our Home
_
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears
Parts
& Repair
Center.
1-800-488-1222
Call anytime,
_
!:
W_P4v.sears.co
To purchase
:
day or night (U.S.A.
%
or
maintenance
agreement
a protection agreement
(Canada)on
de reparaci_n
;
m
a
11._;8003.$827 .I 6655 (U.S.A.)
Para pedir servicio
only)
(U S A )
product
serviced
by
Sears:
1 800 361" 6665 (Canada)
Au Canada
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
_
pour service
1-800-LE-FOYER
en fran_ais:
_c
(1-800-533-6937)
www.sears.ca
8EAR8
® Registered Trademark 1 TMTradem a_k / aM S_rvice Mark of Sears, Roebuck and Go.
M arca Registrada / TMMarca de F_brica / SMMarca de Servlcio de Seers, Roebuck and Co.
_4cMarque de commerce / Mr_Marque deposee de Sears, Roebuck and Co.
© Sears, Roebuck
and Co.