Motorola CLEARTONE CM5000 User guide

When printed by Motorola
Cleartone CM5000
TETRA Mobile Repeater/Gateway
Basic User Guide
1
2
4
3
5
11
3
7
8
6
10
9
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Disposal Information . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
CM5000 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Signal Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keys, Knob, and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotary Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The LED Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering the Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Returning to the Previous Level . . . . . . . . . . . . . . . . . . . . . . . .
Exiting the Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Menu Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating Menu Shortcuts . . . . . . . . . . . . . . . . . . . . . . . .
The Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inbox Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
10
10
10
10
10
11
11
11
11
12
13
13
13
14
15
15
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Powering On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering On with Emergency Button . . . . . . . . . . . . . . . . . . . .
Powering On with Transmit Inhibit Active . . . . . . . . . . . . . . . . .
Unlocking the CM5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
16
17
Selecting Operation Mode . . . . . . . . . . . . . . . . . . . . . . . 18
Entering TMO or DMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Gateway and Repeater Modes . . . . . . . . . . . . . . . . . . . . . . . . . 19
Entering Gateway or Repeater Mode . . . . . . . . . . . . . . . . . . 19
1
English
Contents
Group Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
English
“My Groups” Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the “My Groups” Folder . . . . . . . . . . . . . . . . . . . .
Adding a Group (TMO/DMO) to the “My Groups” Folder . . .
Selecting a Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Alphabetic Search . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Folder Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TMO Group Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a TMO Group Call . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiving a TMO Group Call . . . . . . . . . . . . . . . . . . . . . . . .
DMO Group Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a DMO Group Call . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiving a DMO Group Call . . . . . . . . . . . . . . . . . . . . . . . .
Exiting DMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
20
20
20
20
21
21
21
21
21
22
22
22
Private, Phone, and PABX Calls . . . . . . . . . . . . . . . . . . 23
Creating a Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialling a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialling via the Contact List . . . . . . . . . . . . . . . . . . . . . . . . .
Private Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a Private Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiving a Private Call . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phone and PABX Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a Phone or PABX Call . . . . . . . . . . . . . . . . . . . . . . .
23
23
23
23
24
24
24
24
25
Emergency Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Entering or Exiting Emergency Mode . . . . . . . . . . . . . . . . . . . . 25
Hot Microphone Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Making an Emergency Group Call . . . . . . . . . . . . . . . . . . . . . . 26
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Sending a Status Message . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sending a New Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sending a User-Defined Message . . . . . . . . . . . . . . . . . . . . . .
Sending a Predefined Message . . . . . . . . . . . . . . . . . . . . . . . .
2
26
27
27
27
Handling Unread (New) Messages . . . . . . . . . . . . . . . . . . . . . . 27
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Entering TETRA/UHF Analogue Gateway Mode . . . . . . . . . . . 28
Exiting TETRA/UHF Analogue Gateway Operation . . . . . . . . . 29
Tips & Tricks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Backlight Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Text Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
“My Groups” Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Options (in the Home Display) . . . . . . . . . . . . . . . . . . . .
Easy Navigation while in Menu . . . . . . . . . . . . . . . . . . . .
Exiting the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
30
30
30
30
30
Quick Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . 31
© 2007 by Motorola Inc.
All Rights Reserved.
MOTOROLA and the Stylized M Logo are registered in the U.S.
Patent and Trademark Office. All other product or service names are
the property of their respective owners.
3
English
TETRA/UHF Analogue Gateway Mode . . . . . . . . . . . . . 28
English
4
BUG_EN.fm Page 5 Thursday, October 18, 2007 10:47 AM
This user guide covers the basic operation of the CM5000
Mobile Terminal. Please consult your dealer for further, more
detailed information which is contained in the feature user
guide 6866539D54_.
!
CAUTION: Before using this product, read the operating
instructions for safe usage contained in the Product Safety
and RF Exposure booklet 6866537D37_ enclosed with your
CM5000.
ATTENTION!
The CM5000 is restricted to occupational use only to satisfy
ICNIRP RF energy exposure requirements. Before using this
product, read the RF energy awareness information and
operating instructions in the Product Safety and RF Exposure
booklet (Motorola Publication part number 6866537D37_) to
ensure compliance with RF energy exposure limits.
Keep this User Guide and the Product Safety and RF
Exposure booklet in a safe place and make it available to
other operators in case the CM5000 is passed on to other
people.
Copyright Information
The Motorola products described in this manual may include copyrighted Motorola computer
programs stored in semiconductor memories or other mediums. Laws in the United States and
other countries preserve for Motorola certain exclusive rights for copyrighted computer
programs, but not limited to, including the exclusive right to copy or reproduce in any form the
copyrighted computer program. Accordingly, any copyrighted Motorola computer programs
contained in the Motorola products described in this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in any manner without the express written
permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to
grant either directly or by implication, estoppel, or otherwise, any licence under the copyrights,
patents, or patent applications of Motorola, except for the normal non-exclusive licence to use
that arises by operation of the law in the sale of a product.
5
English
Safety Information
Disposal Information
English
European Union (EU) Waste of Electrical and Electronic
Equipment (WEEE) Directive
The European Union's WEEE directive requires that
products sold into EU countries must have the
crossed out trashbin label on the product (or the
package in some cases). As defined by the WEEE
directive, this cross-out trashbin label means that
customers and end-users in EU countries should not dispose
of electronic and electrical equipment or accessories in
household waste.
Customers or end-users in EU countries should contact their
local equipment supplier representative or service
centre for information about the waste collection system in
their country.
6
CM5000 Overview
This table describes the radio's front panel. See the figure on
the inside front cover.
Item
Description
1
Rotary Knob
Used to turn the radio ON/OFF and to adjust volume level.
2
Microphone Connector
Used to connect a fist microphone in to.
3
Soft Key(s)
Used to select the option that is shown on the display.
4
Menu Key
Used to enter the main menu.
5
Emergency Key
Used to send Emergency Alarms.
6
Navigation Keys
Used for scrolling or text editing.
7
Enter Key
Used to select the required item.
8
Clear Key
Used to clear character or back to the previous screen.
9
Alphanumeric Key
Used to enter alphanumeric characters for dialing,
address book entries and text messages.
10
On Hook / Off Hook Key
Used to initiate or answer calls, end calls or send status
and text messages.
11
LED
Used to indicate the states of the CM5000.
7
English
Controls and Indicators
Audio Signal Tones
= High Tone;
Description
= Low Tone;
Type
Repeated
English
Idle
• Back to Home display
• Back to coverage
• Back to full service
Once
Clear-to-send
Once
Bad key press
Once
• Good key press
• CM5000 self-test fails at
power up
• From out-of-service to inservice
Once
In Call
Call clear warning
Once
Call waiting tone while
Phone or Private Call are
pending.
Every 6 seconds, until
a call is terminated.
Data connected or
Data disconnected
Once
Talk permit sounds upon
pressing the PTT.
Once (Normal Tone)
Once (Short Tone)
Talk permit without
gateway sounds upon
pressing PTT. The tone
indicates the gateway is no
longer available.
Twice
•
•
•
•
Until you release the
PTT.
Talk prohibit
System busy
Time-out timer expire
Called CM5000 not available or busy
Once
• Call disconnected or
failed due to network
• Wrong number dialed
Once
DMO (Direct Mode)
Entering
Once
8
Type
Repeated
Once
Local site trunking –
entering/exiting
Once
Phone ring back (sending)
Every three seconds,
until the called user
answers or call is
rejected.
Phone busy
Every 0.5 seconds
Status message sent to the
dispatcher or failed.
Twice
English
Description
DMO Exiting
Incoming Calls
Status message
acknowledged by the
dispatcher.
Four times
Your CM5000 received a
Group Call without
gateway (setup only).
Once
High-priority Group Call
received
Once
Emergency Alarm sent or
received
Twice
Emergency Alarm failed
Four times
Emergency Call received
Once
Phone ring, full-duplex
Private Call (reception)
According to the Ring Style
sub-menu setting.
Until you answer or
the call is rejected.
Private Call received
Until the call is
answered.
Private Call ringing to the
caller
Until the call is
answered.
Half-duplex Private
Pre-emptive Priority Call
(PPC) ring
Every 4 seconds, until
the call is answered or
rejected.
Full-duplex Private PPC
ring
Every 4 seconds, until
the call is answered or
rejected.
Limited service
Once, upon entering
limited service.
New mail received
Once
9
Description
Type
New Group Call
Repeated
Once
General
English
Volume setting (earpiece,
keypad, speaker)
Continuous
Volume setting (Ringer)
While setting the
volume
Transmit Inhibit (TXI)
Once
DTMF (0-9, #, *) during the
call
DTMF
Continuous, until the
user releases the key
Keys, Knob, and Buttons
Soft Keys
Press upper or lower
to select the option that appears in
the screen directly next to the upper or lower soft key.
Menu Button
Press the Menu button to enter the following:
• The menu (when there is no on-going activity). The CM5000
menus allow you to control the CM5000 settings. Menus are
organised in a hierarchy. The menu options provide access to a
further list of options called a sub-menu.
• The context sensitive menu (when
of items for the current menu.
icon is on) to view a list
Rotary Knob
The rotary knob is used for powering on and off the CM5000
and also as a volume control. Push it down and hold to turn
the device on/off. Turn clockwise to increase the audio
volume level.
Emergency Button
Press and hold this button to enter Emergency Mode.
When the CM5000 is powered down, press and hold this
10
button to power On in Emergency Mode or in standard mode
(as programmed).
The LED Status Indicator
Indicator
English
The LED indicator shows the states of the CM5000.
Status
Solid GREEN
Transmitting
Blinking GREEN
In service
Solid RED
Out of service / Disabled
Blinking RED
Connecting to a network
Solid ORANGE
Transmission Inhibit (TXI) in service
Blinking ORANGE
Incoming call
No indication
Switched off
Entering the Menu Items
1. Press the Menu button.
2. Scroll to the required item, press Select or
to select.
Returning to the Previous Level
Press Back or
.
Exiting the Menu Items
Press
.
The CM5000 exits the menu if no key press is detected for a time-out
period.
11
List of Menu Items
Messages
English
Contacts
Security
Setup
New Message
Inbox
Outbox
Templates
Predefined
Send Status
New Contact
Existing Contacts
PIN Protect
Change Code
Set Ring
Ring Style
Set Volume
Language
Data Setup
Group Audio
Tones
Display
Battery
More...
Group Setup
My Info
Recent Calls
Shortcuts
Networks
Location
PNC Mode
This is the standard menu layout. Your Service Provider may enable/
disable some menu items or change their names.
12
Creating Menu Shortcuts
Use shortcuts to access frequently-used menu items.
Navigate to the menu items. Highlight the item you want to
create a shortcut for. Press and hold the Menu button as the
item is highlighted. Confirm shortcut creation when
prompted.
Menu Shortcut List
To look for assigned shortcuts, press the Menu button and
select More > Shortcuts > <shortcut name>.
Menu Shortcut Use
From Home display, press the Menu button and the numeric
key(s) assigned to the shortcut.
The Display
When you use the CM5000, icons appear on the display to
indicate the following conditions.
Status Icons
Status icons appear when your phone is engaged in certain
activities or when you have activated certain features.
Icon
Description
Signal Strength
Indicates the signal strength in the current TMO or DMO area.
Four bars indicate the maximum strength. Fewer bars indicate
lower signal strength. You may be able to improve signal
strength by moving your vehicle to a different location.
New Message Has Arrived
Indicates that a new message just arrived. Once you change
the display the icon disappears.
New Message(s) in Inbox
Indicates that an unread message is in stack. Once you read
the message the icon disappears.
All Tones Off
No audible alert tones. The screen displays incoming calls.
No Speaker
Indicates no speaker output.
13
English
Menu Shortcut Creation
Icon
Description
GPS
Appears when the CM5000 receives the GPS signal.
English
Data Connected
Appears when the CM5000 is in Packet Data Mode.
Emergency
Appears when the CM5000 is in Emergency mode.
Scan
Appears when the CM5000 is in Group scan mode.
Direct Mode (DMO)
Appears when the CM5000 is in Direct Mode.
Gateway Mode
Indicates in-service state for Gateway Mode.
Indicates CM5000 fixed communication through Gateway.
Repeater Mode
Indicates in-service state for Repeater Mode.
Indicates CM5000 fixed communication through Repeater.
Menu Icons
The following icons make it easy to identify the menu items at
first glance.
Menu Icon
Description
Main Menu Items/Context Sensitive Menu
Appears above the Menu button if the main menu items/
context sensitive menu are active.
Messages
• Send status messages,
• Send short text messages (free text or according to user
defined or predefined templates),
• Receive messages in inbox.
Contacts
Add, search, edit, or erase entries in the contact list.
Security
Lets you turn On/Off and verify security features, and change
passwords.
Setup
Allows you to customise the CM5000.
More...
Contains more customisable menu items.
14
Description
Scroll Bar
Indicates navigation among items that occupy more than one
screen. If all items appear in one screen, the scroll bar is
empty.
Inbox Icons
The following icons indicate the status of messages in the
inbox.
Inbox Icon
Description
Unread (New) Message
Indicates that you have not read the message yet.
Read (Old) Message
Indicates that you have read the message.
Sender Information in Message View
Indicates sender information (name or number).
Time and Date Stamp in Message View
Indicates the time and date of message arrival.
Contact Icons
In the contact list display, the following icons may appear
next to the contact numbers to indicate the type of stored
number.
Contact Icon
Description
Private ID Number
Mobile Phone Number
Home Phone Number
Work Phone Number
PABX Number
Other Phone Number
Pickers
Indicate more than one number is stored with the contact.
15
English
Menu Icon
Getting Started
Powering On/Off
English
To power On, press and hold the rotary knob. The CM5000
performs a self-check and registration routine. After
successful registration, the CM5000 is in service.
To power Off, press and hold the rotary knob push button.
You hear a beep and the Powering Off message is
displayed.
Powering On with Emergency Button
Press and hold the Emergency button to power On. The
CM5000 powers On in Emergency Mode or in standard
mode (as programmed).
Powering On with Transmit Inhibit Active
Transmit Inhibit (TXI) is a feature allowing you to switch off
transmission before entering a Radio-Frequency (RF)
sensitive area. To activate this feature, press the Menu
button and select More...> Networks > TXI Mode >
Activate.
!
Warning:
Pressing the Emergency button, even if Transmit Inhibit is activated,
causes the CM5000 to transmit immediately. The CM5000 must NOT
be within the RF sensitive area when entering Emergency Mode.
The TXI Mode remains active at power On. You are
prompted whether to leave the TXI Mode On or not.
!
Warning:
Ensure you have left the RF sensitive area before deactivating Transmit
Inhibit.
Press the Yes soft key to deactivate the TXI Mode. If the
CM5000 was previously used in Trunked Mode, it will register
to the network. If the CM5000 was previously used in Direct
Mode, it will remain in Direct Mode.
Press No in Trunked Mode and the CM5000 powers down.
16
Press No in Direct Mode and you remain in Direct Mode with
TXI selected.
The CM5000 may be locked at power up.
To unlock the CM5000 after powering on, enter the code at
the prompt. The CM5000 enters the default Home display.
The unlock code is originally set to 0000. Your Service
Provider may change this number before you receive your
terminal.
17
English
Unlocking the CM5000
Selecting Operation Mode
Entering TMO or DMO
English
Enter TMO or DMO in one of the following ways:
• From the Home display press Optns and select Direct Mode if
the CM5000 is in TMO.
• From the Home display press Optns and select Trunked Mode if
the CM5000 is in DMO.
• Press the Menu button and select More...> Networks > Trunked
Mode if the CM5000 is in DMO.
• Press the Menu button and select More...> Networks > Direct
Mode if the CM5000 is in TMO.
• Press the TMO/DMO one-touch button (if programmed by your
Service Provider).
You can make and receive the following types of calls when
the CM5000 operates in Trunked Mode:
•
•
•
•
•
Group Calls
Private Calls
Phone Calls
PABX Calls — local (office) extension calls
Emergency Calls.
You can make and receive Group Calls when the CM5000
operates in Direct Mode. This includes Emergency Group
Calls.
The CM5000 returns to the Home display when there is no
activity for a few seconds.
Your terminal can alert you of an incoming call. Select the alert settings
in the Tones menu items.
18
In Gateway Mode Operation communication relay between
TMO and DMO is available. DMO terminals communicate
with the trunked system (and the other way around).
In Repeater Mode Operation the CM5000 re-transmits
information received from one DMO terminal to the other
DMO terminal enhancing the coverage area.
Entering Gateway or Repeater Mode
When the CM5000 is in TMO enter Gateway or Repeater
Mode in one of the following ways:
• From the Home display press Optns and select Gateway
Mode or Repeater Mode as required.
• Press the Menu button and select More... > Networks >
Gateway Mode or Repeater Mode as required.
19
English
Gateway and Repeater Modes
Group Calls
English
A Group Call is a communication between you and others in
a group. A group is a predefined set of subscribers enabled
to participate in and/or invoke a Group Call.
Groups are organised in folders. Each folder may contain
several groups.
“My Groups” Folder
You can organise your favorite groups into one folder called
“My Groups”.
Selecting the “My Groups” Folder
From the Home display, press
to quickly access the folder.
Adding a Group (TMO/DMO) to the “My Groups” Folder
1. Press the Menu button and select More > Group Setup > My
Groups > Edit List > [New Group].
2. Select a group by alphabetic search (“TMO/DMO by abc”). Enter
the first character of the group name. Or select a group by folder
search (“TMO/DMO by Folder”). Select the folder and select the
group. The group is added to the “My Groups” folder.
Selecting a Group
When you navigate in the “My Groups” folder and select a DMO group,
your terminal switches between TMO and DMO (and contrariwise).
Using Alphabetic Search
From the Home display, press Optns. Select a group by
alphabetic search (“TG by abc”). Enter the first character of
the group name. Select the group.
Using Folder Search
From the Home display, press Optns. Select a group by folder
search (“TG by Folder”). Select the folder and select the
group.
20
From the Home display, press Optns. Select Folder, and
select the desired folder. The display shows the last selected
group in that folder.
TMO Group Calls
In TMO the CM5000 is used with your Service Provider’s
infrastructure.
Making a TMO Group Call
1. From the Home display and if this is the required group,
press and hold the PTT.
2. Wait for the talk permit tone (if configured) and then speak
into the microphone. Release the PTT button to listen.
When you start a call, all members of the selected group who
have their units turned on, receives the Group Call.
The “No Group” message is displayed when you are out of the normal
coverage area of your selected group. You must then select a new
group that is valid for your working location.
Receiving a TMO Group Call
Unless it is engaged in a call, the CM5000 receives the
Group Call. To answer the call, press and hold PTT.
The CM5000 shows the group name and the caller’s private
number or alias if previously stored in your contact list.
DMO Group Calls
In DMO the CM5000 can be used without your Service
Provider’s infrastructure.
DMO allows communication with other terminals also
operating in DMO, which are on the same frequency and
group as the CM5000.
When you start a call, the members of the selected group
who have their units turned on receive the Group Call.
21
English
Selecting a Folder
In DMO the CM5000 can communicate with the trunking
system (and the other way around) if the Gateway option is
enabled in the CM5000.
English
Making a DMO Group Call
Select the group from Talkgroup list you require. Press PTT
button and wait for the grant tone before speaking into the
microphone. Remember to release the PTT to listen.
Receiving a DMO Group Call
When an Group call is received the mobile automatically
switches to group mode and receives the call, also the group
caller name appears on the screen.
Exiting DMO
To exit DMO, press Optns and select Trunked Mode.
22
Private, Phone, and PABX Calls
1. From the Home display, press Contcs. Select [New Contact].
2. Enter name. Press Ok to confirm.
3. Press
/
and select the type of stored number (such as
Private).
4. Enter number (#). Press Ok.
5. Continue to enter other types and numbers, as you may keep
several numbers (Private, Mobile, Home, Work, PABX, Other) for
the same person under the same contact name. To correct an
entry, press Change.
6. When finished, press Done. Press Back to return to Home
display.
Dialing
Dialling a Number
1. From the Home display select call type (Private, Phone, or PABX)
using
/
.
2. Dial a number.
3. Press PTT or
depending on the call type.
Dialling via the Contact List
Press Contcs and search the stored number by scrolling
( or ) or by entering the first character of the contact
name. If the contact has more than one number, use
or
to select the number.
23
English
Creating a Contact
Private Call
English
A Private Call, also called Point-to-Point or an individual call,
is a call between two individuals. No other terminal can hear
the conversation.
Making a Private Call
1. From the Home display select Private Mode using
/
.
2. When in Private Mode, dial a number.
3. Press and hold the PTT button. Wait for the talk permit tone (if
configured) before talking, and release the PTT when listening.
4. To end the call press
.
While Transmit Inhibit is activated, an incoming Private Call is indicated,
but you cannot answer the call.
Receiving a Private Call
1. The CM5000 switches to the incoming Private Call. The display
shows incoming call notification and the caller’s identity.
2. To answer an incoming call, press PTT.
3. To reject or end the call, press
.
Your terminal can alert you of an incoming call. Select the alert settings
in the Tones menu items
Phone and PABX Calls
The Phone Call allows you to call a landline telephone
number or a cellular mobile phone number.
The Private Automatic Branch Exchange (PABX) Call
allows you to call local (office) extension numbers. This type
of call needs to be activated by your Service Provider.
In this publication we use “phone number” when referring to
these numbers.
While Transmit Inhibit is activated, an incoming Phone or PABX Call is
indicated, but you cannot answer the call.
24
Making a Phone or PABX Call
1. From the Home display select Phone or PABX Mode
/
.
3. Press and release
. You will hear a ringing tone. Wait for the
called person to answer your call.
4. To end the call, press
.
Emergency Mode
The CM5000 enables you to send and receive Emergency
Group Calls in Trunked Mode or in Direct Mode. If your
terminal is configured to operate through a gateway,
Emergency calls can be placed through the gateway.
The Emergency Group Call can be initiated and received
from the following subscribers:
• the selected group (TMO and DMO) (if tactical emergency)
• a predefined group (if non-tactical emergency)
Contact your Service Provider to know which is the selected
mode.
Your Service Provider needs to configure the Emergency
Alarm and Hot Microphone features.
Emergency calls are allocated emergency priority in the
system.
Entering or Exiting Emergency Mode
To enter Emergency Mode, press and hold the Emergency
button.
Pressing the Emergency button even if Transmit Inhibit is activated
causes immediately the CM5000 to transmit. When entering Emergency
Operation the CM5000 should not be within the RF sensitive area any
longer!
25
English
using
2. When in Phone or PABX, select a pre-programmed number from
the contact book or dial a number.
To exit Emergency Mode, press and hold Exit. Your terminal
switches to the Home display.
Hot Microphone Feature
English
If the Hot Microphone feature was programmed into the
CM5000 by your Service Provider, you are enabled to make
an Emergency Group Call and talk to the dispatcher (and
members of your group) without the need to press and hold
the PTT.
The microphone stays open for a time period (programmed
by your Service Provider). The microphone stays open until:
•
the Hot microphone time period expires.
•
you press the On-Hook key.
At the end of the Hot Microphone the CM5000 returns to the
Emergency Mode. The Hot Microphone feature is disabled
and PTT operation returns to normal.
If required you can resume Hot Microphone by pressing and
holding the Emergency button again.
Making an Emergency Group Call
To initiate or answer a call while in Emergency Mode:
•
Press and hold PTT.
•
Wait for the talk permit tone (if configured) and talk.
•
Release PTT to listen.
Messages
Sending a Status Message
Select the desired group, then press the Menu button and
select Messages > Send Status. Select status and press
Send.
26
Press the Menu button and select Messages > New
Message. Write your message. Press Ok select the recipient
or enter the address directly. Select Send to send the
message.
Sending a User-Defined Message
Press the Menu button and select Messages > Templates.
Scroll and choose your required template. Select Send.
Select your mail recipient or enter number. Select Send.
Sending a Predefined Message
Press the Menu button and select Messages > Predefined.
Scroll and choose your required template. Press the Menu
button and select Edit to edit the message. Type required
information. Select Send or PTT to send the message.
Handling Unread (New) Messages
Press the Menu button and select Messages > Inbox. Scroll
to the message and select Read soft key. To read a long
message, press More to read the next page and Back to
return to the previous page.
Press the Menu button and select to store/delete/delete all/
reply/forward.
For Long Text Messages Reply, Store and Forward options are not
available.
27
English
Sending a New Message
TETRA/UHF Analogue Gateway Mode
English
General
The CM5000 allows you to establish gateway connection
between the TETRA network and an UHF analogue system.
Each time an unencrypted analogue radio user transmits to the
TETRA network an audible warning tone is sent to TETRA users in
group.
Entering TETRA/UHF Analogue Gateway Mode
The CM5000 must be connected to an analogue radio
through an analogue radio interface.
Choose the required TMO talkgroup before entering the
analogue/digital mode.
The CM5000 can switch to the analogue/digital mode only in group
mode.
To enter the analogue/digital gateway mode:
1. From the Home display press
U
Menu button and then
9 alphanumeric key. The
display shows the current UHF
channel selected on UHF
mobile.
2. Select the required UHF
channel using up/down navigation keys.
3. Select Gte to enter the analogue/digital gateway operation
Select Tet to return to TMO or DMO mode.
28
Exiting TETRA/UHF Analogue Gateway Operation
English
To exit the analogue/digital
gateway mode, from the UHF
Gateway display select Esc.
U
29
Tips & Tricks
Backlight Control
English
You can control the intensity of the backlight via the Backlight
Control function key.
Menu Shortcuts
• You can easily access any menu item, by pressing the Menu
button and a Numeric key. (No delay between the Menu button
and the key!)
• You can ask your Service Provider to program menu shortcuts.
• You may also define a new shortcut: enter the menu item, press
and hold the Menu button, and follow the instructions in the
display.
Text Size
To set the text size from Standard to Zoomed press Menu >
Setup > Display > Text Size.
“My Groups” Folder
You can select any group (TMO or DMO) and add it to your
personal folder.
In the Home display, press
Groups” folder.
to quickly access your “My
Options (in the Home Display)
You can easily change folder, select groups, switch between
TMO and DMO (and vice-versa), and other functions via the
Home display Options.
Easy Navigation while in Menu
When scrolling up/down menu items, try also right/left
scrolling. (This selects the item or returns to previous level.)
Exiting the Menu
Wherever in the menu press the On-Hook key to exit to the
Home display.
30
Soft Keys
On/Off Hook
Keys
LED
Emergency
Button
Menu Key
Enter Key
Clear Key
Alphanumeric
Navigation Key
Display
Microphone
Connector
Rotary Knob/
Power On
Display Icons
Alphanumeric
Cleartone CM5000
Quick Reference Guide
.
From the Home display navigate to
the desired group. Press Select soft
key (if configured). Press and hold
PTT. Wait for the talk permit tone (if
configured) and talk. Release PTT to
listen.
Making a TMO Group Call
• Switching to Gateway or Repeater
modes is possible in TMO only
• From the Home display press
Optns, select Trunked Mode/Direct
Mode/Gateway Mode/Repeater
Mode.
Selecting Trunked/Direct/Gateway/Repeater Mode Operation
Back or
• To enter the menu, press the Menu
button.
• To scroll through the menu, press
/ .
• To select a menu item, press Select
soft key or
.
• To return to previous level, press
Using the CM5000 Menu System
To power the CM5000 on/off, press
and hold the Knob.
Turning the CM5000 On/Off
English
Release PTT to listen. Press
terminate call.
to
mode using
or
. Dial a number.
Press and release PTT. Ringing
sounds. Called party answers. Wait
for the called party to finish speaking.
Press and hold PTT. Wait for the talk
permit tone (if configured) and talk.
From the Home display select Private
Making a Private Call
Press and hold the Emergency button.
Press and hold PTT. Wait for the talk
permit tone (if configured) and talk.
Release PTT to listen. If using “Hot
Mic” feature, wait for the Emgncy Mic
On message to appear on the display
and talk without pressing PTT.
To exit Emergency Mode, press and
hold Exit soft key.
Making an Emergency Group Call
Enter DMO. Navigate to the desired
group. Press Select soft key (if
configured). Press and hold PTT. Wait
for the talk permit tone (if configured)
and talk. Release PTT to listen.
Making a DMO Group Call
.
Backlight Control
You can either disable backlight
(covered operation) or have it
automatically turned on, by any key
press.
•
Tips & Tricks
Press the Menu button and select
Messages > New Message. Write
your message. Select Send. Select
your mail recipient or enter number.
Select Send, or press PTT to send the
new message.
Sending a New Message
Select the desired group, then press
the Menu button and select
Messages > Send Status. Select
status and press Send.
Sending a Status Message
call press
The CM5000 switches to the incoming
call and alerts you of the incoming
call. To answer the call, press PTT to
answer the call. To reject or end the
Answering a Call
Menu Shortcuts
Group Audio Control
Unified Contact List
Text Size
To set the text size from Standard to
Zoomed press Menu > Setup >
Display > Text Size.
•
You can keep several numbers
(Private, Mobile, Home, Work, PABX,
Other) for the same person under the
same contact name.
•
You can control audio level for any
Private or Group Call. However, you
can define via the menu to have all
Group calls always loud (Menu button
> Setup > Group Audio).
•
You can easily access any menu item,
by pressing the Menu button and a
numeric key. (No delay between the
Menu button and the key!)
You can ask your Service Provider to
program menu shortcuts.
You may also define a new shortcut:
enter the menu item, press and hold
the Menu button, and follow the
instructions in the display.
•
“My Groups” Folder
PIN Protect
To protect access to network
operation, from the main menu, select
Security > PIN Protect.
•
to
In the Home display, press
quickly access your “My Groups”
folder.
You can select any group (TMO or
DMO) and add it to your personal
folder.
•
English
EN
6866539D69-A
www.motorola.com/tetra
@6866539D69@