Emerson CF4900BS00 Owner`s manual

BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 1
READ AND SAVE THESE INSTRUCTIONS
SOUTHTOWNE™
54” Ceiling Fan Owner's Manual
Model Numbers
CF4900BS00
Brushed Steel
CF4900ORB00
Oil Rubbed Bronze
CF4900VS00
Vintage Steel
Net Weight:
??.?
Lbs.
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., Eastern, Monday-Friday
Part No. F40BP74850000
Revision: 131201
1-800-654-3545
www.emersonfans.com
Form No. BP7485
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 2
Table of Contents
Section
Page
8. Wall Control Procedures . . . . . . . . . . . . . . . . . . . . . .16-22
9. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
10. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
11. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-25
12. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
13. Remote Control Trouble Shooting . . . . . . . . . . . . . . . .26
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . .27
Section
Page
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1. Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . .3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .4
3. Ceiling Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
4. How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . .8-9
5. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . .10-12
6. Light Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14
7. No Light Cover Assembly . . . . . . . . . . . . . . . . . . . . .15-16
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
!
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall control/
switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To avoid fire, shock or injury, do not use an
Emerson or any other brand of control not specifically
approved for this fan.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
NOTE: This fan is suitable for use in wet locations when
installed in a GFCI protected branch circuit.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2014” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
2
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 3
1. Unpacking Instructions
!
PACKAGE CONTENTS
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
1-800-654-3545
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
1.1
Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
HARDWARE CONTENTS
Part
1
2
3
4
5
6
7
8
9
10
11
12
Description
Fan Motor Assembly
Ceiling Cover
Coupler Cover
No Light Cover
Light Kit Assembly
Glass Assembly
Fan Blades
Fan Blades Flanges
Hanger Bracket
Hanger Ball/4.5” Downrod Assembly
50-Watt Halogen Bulbs
RCK55 Receiver
SW605 Wall Control, 6-Speed LED
Quantity
1
1
1
1
1
1
5
5
1
1
2
1
1
F
A
Description
Quantity
Threaded Studs, #8-32 x 1-1/4”
4
Knurled Knobs, #8-32
4
Lockwashers, External Tooth #8
4
Wire Connectors, 12 ga.
5
Clevis Pin
1
Hairpin Clip
1
#10-32 x 1/4” Washer Head Blade Screws
15
1/4-20 x 3/8” Pan Head Screws
with Lockwashers
21
1/4-20 x 3/8” Oval Head Screw
with Lockwasher (spare)
1
Setscrew Wrench
1
Setscrew
1
Blade Balance Kit
1
I
B
J
C
K
D
L
E
OFF
ON
M
1
G
4
3
2
5
6
H
7
8
9
10
11
12
1.2
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
Remove the fan motor assembly from the protective
plastic bag.
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 4
1. Unpacking Instructions (continued)
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
1.3
Remove and discard the cardboard shipping retainer
securing the motor hub in the motor housing assembly.
One Phillips head screwdriver
One 1/4” blade screwdriver
One stepladder
One wire stripper
Materials
FAN MOTOR
ASSEMBLY
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Wire Size A.W.G.
14
12
Installed Wire Length
Up to 50 ft.
50-100 ft.
CARDBOARD
SHIPPING
RETAINER (2)
!
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 10). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
1.4
Place the fan assembly into the upper foam pad with the
bottom of the motor facing up.
The upper foam pad serves as a holder for the fan
during assembly.
2. Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
!
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
!
!
WARNING
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
4
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 5
3. Ceiling Fan Assembly
3.1
Position the fan blade on top of the blade flange by
aligning the three raised bosses into the blade mounting
holes.
#10-32 x 14" WASHER
HEAD BLADE SCREWS
(3 per blade assembly)
Install the three #10-32 x 1/4” Washer Head Blade
Screws into the mounting holes of the fan blade
assembly and tighten securely (Figure 1). I
FAN BLADE (5)
Complete the installation of the remaining four blades
per the above instructions.
FAN BLADE
FLANGE (5)
Figure 1
3.2
#10-32 x 5/8" OVAL HEAD BLADE SCREW (4)
Slide the fan blade assembly through the blade slot in
the fan motor housing assembly (Figure 2).
MOTOR HOUSING ASSEMBLY
Mount the fan blade assembly to fan motor housing
assembly using four #10-32 x 5/8” oval head blade
screws (Figure 2).
FAN BLADE ASSEMBLY
NOTE: Take care not to scratch fan motor housing
assembly when installing blade assemblies.
Complete the installation of the remaining four blade
assemblies per the above instructions.
!
WARNING
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
Figure 2
3.3
CEILING FAN
(partially assembled)
Turn the partially assembled ceiling fan right side up for
final installation. Place the fan carefully onto the top of
the styrofoam as not to bend the ceiling fan blades
(Figure 3).
STYROFOAM
Figure 3
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 6
3. Ceiling Fan Assembly (continued)
3.4
PIN
Remove the hanger ball by loosening the setscrew in
the hanger ball until the ball falls freely down the
downrod (Figure 4).
HANGER BALL
Remove the pin from the downrod, then remove the
hanger ball. Retain the pin and hanger ball for
reinstallation in Step 3.10.
SETSCREW
DOWNROD
Figure 4
3.5
Separate, untwist and unkink the three 80” motor leads.
Route the motor lead wires through the downrod.
Align the clevis pin holes in the downrod with the holes
in the motor coupling. Install the clevis pin and secure
with the hairpin clip (Figure 5).
The clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Be sure to push
the straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of the
hairpin clip snaps around the clevis pin.
The hairpin clip must be properly installed to prevent the
clevis pin from working loose. Pull on the downrod to
make sure the clevis pin is properly installed.
DOWNROD
DOWNROD
HAIRPIN
HAIRPIN
CLIP
CLIP
SETSCREW
(2)
SETSCREW
CLEVIS
PIN
CLEVIS PIN
MOTOR
MOTOR
COUPLING
COUPLING
Figure 5
3.6
Insert the setscrew (supplied in loose parts bag) into the
motor coupler hole until it rest against the downrod.
MOTOR
COUPLING
Securely tighten the setscrew using the 5/32" setscrew
wrench (provided).
SETSCREW (1)
5/32"
SETSCREW
WRENCH
Pull up on the downrod to make sure the setscrew is
firmly installed against the motor coupler (Figure 6).
NOTE: The setscrew must be properly installed as
described above, or fan wobble could result.
!
WARNING
It is critical that the clevis pin in the motor coupling is
properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
Figure 6
6
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 7
3. Ceiling Fan Assembly (continued)
3.7
Screw two #8-32 x 1-1/4” threaded studs (provided) into
the motor (Figure 7).
#8-32 x 1-1/4"
THREADED
STUD (2)
Leave approximately 7/8” of the stud extending above
the motor.
7/8"
MOTOR
Figure 7
3.8
NOTE: Make sure the red and brown leads are
capped with wire connectors. During installation of
coupler cover, be sure the red, brown and yellow
wires and wire connectors are completely inside
motor coupler cover and not pinched between the
motor coupler cover and motor.
DOWNROD
#8-32 KNURLED
KNOB (2)
MOTOR
COUPLER
COVER
#8 EXTERNAL
TOOTH
LOCKWASHER (2)
#8-32 x 1-1/4"
THREADED
STUD (2)
Slide the motor coupler cover over the downrod and
rotate the cover until the threaded studs protrude
(Figure 8).
Install the two #8 external tooth lockwashers and #8-32
knurled knobs (supplied) to secure the motor coupler
cover (Figure 8).
Figure 8
3.9
PIN
Pass the 80-inch long motor leads through the opening
in the ceiling cover. Be sure the cover is oriented
correctly (Figure 9).
HANGER BALL
DOWNROD
CEILING
COVER
3.10
SETSCREW
Reinstall the hanger ball (Figure 9) on the downrod as
follows. Route the motor leads through the downrod.
Position the pin through the two holes in the downrod
and align the ball so the pin is captured in the groove in
the top of the hanger ball. Pull the hanger ball up tight
against the pin and securely tighten the setscrew in the
hanger ball. A loose setscrew could create fan wobble.
Figure 9
3.11
The fan comes with blue, black and white leads that are
80-inches long. Before installing the fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and strip
back insulation 1/2-inch from end of leads.
!
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened. Failure
to verify that the pin and setscrew are properly
installed could result in the fan falling.
7
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 8
4. How to Hang Your Ceiling Fan
!
WARNING
CEILING
The fan must be hung with at least 7' of clearance from
floor to blades (Figure 10).
AT LEAST
7'
FLOOR
Figure 10
!
WARNING
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
!
OUTLET
BOX
WARNING
HANGER
BRACKET
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
TAB
4.1
Figure 11
Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 11.)
!
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
8
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 9
4. How to Hang Your Ceiling Fan (continued)
4.2
Screw the two 1-1/4” threaded studs (supplied) into the
tapped holes in the hanger bracket (Figure 12).
OUTLET BOX
HANGER BRACKET
Figure 12
1-1/4" THREADED
STUDS (2)
4.3
NOTE: CEILING COVER, SUPPLY
WIRES AND FAN WIRES OMITTED
FOR CLARITY.
Carefully lift the fan and seat the hanger ball/
downrod assembly on the hanger bracket that was just
attached to the outlet box (Figure 13).
OUTLET
BOX
Be sure the groove in the ball is lined up with tab on the
hanger bracket (Figure 12).
!
WARNING
HANGER
BRACKET
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
HANGER BALL/
DOWNROD
ASSEMBLY
!
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
Figure 13
9
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 10
5. How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
DOWNROD
RCK55
RECEIVER
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan, light kit or receiver.
!
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
!
CEILING
COVER
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
Figure 14
Position the RCK55 Receiver (supplied) in the ceiling
cover so that the flat side of the receiver faces up and
the open portion of the receiver is to the right, as shown
in Figure 14.
5.1
Pull the wire leads, coming from the end of the
downrod, and the supply wires through the open side of
the hanger bracket. (Figure 14).
5.2
!
NOTE: Make all wiring connections using wire
connectors (supplied). Make sure that all
connections are tight, including ground, and that no
bare wire is visible at the wire connectors, except
for the ground wire.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
!
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
10
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 11
5. How to Wire Your Ceiling Fan (continued)
Cut off the ends of the blue and yellow receiver wires
and strip back insulation 1/2-inch from the ends of the
wires.
5.3
Using wire connectors (supplied), make wiring
connections as follows (Figure 15 and 16):
Connect the blue fan wire to the blue receiver wire
(BOTTOM LIGHT).
Connect the white fan wire and the white supply wire to
the white receiver wire (AC IN/ MOTOR N).
Connect the black fan wire to the black receiver wire
(TO MOTOR L).
Connect the green ground wires from the hanger
bracket and the hanger ball to the supply ground wire
(bare or green).
Connect the black supply wire to the black/white
receiver wire (AC IN L).
Yellow receiver wire - Do Not Use. Keep capped.
OUTLET BOX
BLACK SUPPLY WIRE
BLACK FAN WIRE
HANGER BRACKET
HANGER BRACKET
GROUND WIRE
(GREEN)
BLACK/WHITE RECEIVER WIRE
BLUE FAN WIRE
HANGER BALL
GROUND WIRE
(GREEN)
BLUE RECEIVER
WIRE
OPEN
PORTION OF
RECEIVER
HERE
SUPPLY GROUND
WIRE (GREEN OR
BARE)
YELLOW RECEIVER WIRE
DO NOT USE
RECEIVER
BLACK RECEIVER WIRE
WHITE SUPPLY
WIRE
WHITE RECEIVER WIRE
WHITE FAN WIRE
WIRE CONNECTOR
CEILING COVER
Figure 15
RCK55 RECEIVER
BLACK
SUPPLY
WIRE
WHITE RECEIVER WIRE
BLACK RECEIVER WIRE
TO
110V
SUPPLY
WHITE SUPPLY
WIRE
BLACK/WHITE
RECEIVER WIRE
BLUE RECEIVER WIRE
WHITE FAN WIRE
BLUE FAN WIRE
BLACK FAN WIRE
YELLOW RECEIVER WIRE
DO NOT USE
DOWNROD
Figure 16
11
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 12
5. How to Wire Your Ceiling Fan (continued)
5.4
After connections have been made, separate the white
and green wires from the black, blue and yellow wires.
OUTLET BOX
Carefully turn the wires upward and insert them up
through the open side of the hanger bracket and into the
outlet box.
HANGER
BRACKET
Push the green and white wires into one side of the
outlet box; push the black, blue and yellow wires into
the other side of the outlet box (Figure 17).
RECEIVER
CEILING
COVER
Figure 17
5.5
Lift the ceiling cover up to the threaded studs and turn
until studs protrude through the holes in the ceiling
cover (Figure 18).
5.6
CEILING COVER
Secure the ceiling cover in place by sliding lockwashers
over the threaded studs and installing the two knurled
knobs (supplied). (Figure 18).
THREADED
STUDS (2)
LOCKWASHERS (2)
KNURLED KNOBS (2)
Tighten the knurled knobs securely until the ceiling
cover fits snugly against the ceiling and the hole in the
ceiling cover is clear of the downrod.
!
Figure 18
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
Please call Emerson technical support at
1-800-654-3545 if you have any questions
about installation and operation of this ceiling fan.
12
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 13
6. Light Kit Assembly
6.1
Engage the white connector wire from the fan motor
assembly to the light kit assembly white connector wire
until you hear a snap (Figure 19).
Engage the black connector wire from the fan motor
assembly to the light kit assembly black connector wire
until you hear a snap (Figure 19).
FAN MOTOR
ASSEMBLY
BLACK WIRE
FAN MOTOR
ASSEMBLY
WHITE WIRE
LIGHT KIT ASSEMBLY
BLACK WIRE
LIGHT KIT ASSEMBLY
WHITE WIRE
Figure 19
6.2
Remove one of the three 1/4-20 x 3/8” oval head screws
with lockwashers from the fan motor assembly
(Figure 20). Retain the screw for future installation.
Loosen the other two screws.
Carefully tuck all the wires under the light kit assembly
prior to installing the light kit assembly onto the fan
motor assembly.
Place the light kit assembly onto the light kit cover.
Rotate the light kit assembly to engage the two loosen
screws and tight the two loosened screws.
Reinstall the 1/4-20 x 3/8” oval head screw with
lockwasher (previously removed) into the light kit
assembly to secure.
!
LIGHT KIT
ASSEMBLY
1/4-20 x 3/8" OVAL HEAD
SCREWS WITH
LOCKWASHERS (3)
WARNING
Figure 20
To avoid possible fire or shock, do not pinch wires
between the light kit assembly and the fan motor
assembly.
13
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 14
6. Light Kit Assembly (continued)
6.3
Screw the two 50-watt (maximum) halogen mini
candelabra base bulbs in the light kit assembly sockets
(Figure 21).
NOTE: Do not touch halogen mini candelabra base
bulb with bare hands. Fingerprints may result in
shorter bulb life. Remove fingerprints with rubbing
alcohol.
!
LIGHT KIT
ASSEMBLY
SOCKET (2)
WARNING
To avoid risk of burns or other injuries, turn power off
and allow lamps to fully cool before attempting to
replace the halogen mini candelabra base bulbs.
5-WATT (maximum) HALOGEN
MINI CANDELABRA BASE BULB (2)
Figure 21
6.4
POSITION THE GLASS ASSEMBLYKEYHOLE SLOTS STRAIGHT UP ONTO
THE LIGHT KIT ASSEMBLY PROTRUDING SCREWS.
ROTATE THE GLASS ASSEMBLY CLOCKWISE TO SECURE ONTO
PROTRUDING SCREWS AND METAL BANDS.
Carefully slide the glass assembly over the light kit
assembly (Figure 22).
LIGHT KIT METAL
BANDS (3)
Position the light kit assembly’s protruding screw heads
into the three keyhole slots of the glass assembly
(Figure 22).
LIGHT KIT
PROTRUDING
SCREW
HEADS (3)
Rotate the glass assembly clockwise to engage the
screw heads to secure the assembly (Figure 22).
GLASS
ASSEMBLY
KEYHOLE
SLOTS (3)
NOTE: The three metal bands on the light kit
assembly will add extra security to the glass
assembly.
LIGHT KIT
ASSEMBLY METAL
BANDS (3)
Figure 22
14
LIGHT KIT
ASSEMBLY
PROTRUDING
SCREW HEADS (3)
GLASS
ASSEMBLY
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 15
7. No Light Cover Assembly
7.1
LIGHT KIT METAL
BANDS (3)
Removal of the glass from the glass assembly:
Rotate the glass assembly counter-clockwise to disengage the screw heads from the assembly (Figure 23).
LIGHT KIT
PROTRUDING
SCREW
HEADS (3)
Remove the light kit assembly’s protruding screw heads
from the three keyhole slots of the glass assembly
(Figure 23).
Remove the glass assembly from the light kit assembly
(Figure 23).
!
GLASS
ASSEMBLY
KEYHOLE
SLOTS (3)
WARNING
Do not install any light bulbs into the light kit plate if
using the cover plate. Installation of light bulbs when
using the cover plate could result in fire, shock and
serious personal injury.
LIGHT KIT
ASSEMBLY METAL
BANDS (3)
LIGHT KIT
ASSEMBLY
PROTRUDING
SCREW HEADS (3)
GLASS
ASSEMBLY
Figure 23
7.2
Unscrew the two 50-watt (maximum) halogen mini
candelabra base bulbs from the light kit assembly
sockets (Figure 24).
NOTE: Do not touch halogen mini candelabra base
bulb with bare hands. Fingerprints may result in
shorter bulb life. Remove fingerprints with rubbing
alcohol.
!
WARNING
To avoid risk of burns or other injuries, turn power off
and allow lamps to fully cool before attempting to
remove the halogen mini candelabra base bulbs.
LIGHT KIT
ASSEMBLY
SOCKET (2)
REMOVE THE 5-WATT HALOGEN
MINI CANDELABRA BASE BULB (2)
Figure 24
15
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 16
7. No Light Cover Assembly (continued)
7.3
CLAMP SCREW
GLASS SHADE CLAMP
Loosen the three glass assembly screws on the inside
of the glass assembly (Figure 25).
RUBBER PAD
Rotate the three glass shade clamps to free the glass
shade.
GLASS SHADE
Be sure not to loosen the rubber pads beneath each
clamp, needed for proper clamping.
Carefully remove the glass shade by lifting it out of the
glass assembly and store in a safe place for possible
future use (Figure 25).
GLASS SHADE
CLAMPS (3)
LOOSEN GLASS ASSEMBLY
SCREWS (3)
ROTATE SHADE CLAMPS (3)
REMOVE
GLASS
SHADE
GLASS ASSEMBLY
Figure 25
7.4
CLAMP SCREW
GLASS SHADE CLAMP
Place the no light cover inside the glass assembly
(Figure 26).
RUBBER PAD
Make sure the outer ring of the no light cover is
protruding through the glass assembly.
NO LIGHT
COVER
Rotate the three glass shade clamps over the inner
edge of the no light cover.
Be sure to keep the rubber pad beneath each clamp to
ensure proper clamping.
RETIGHTEN GLASS ASSEMBLY
SCREWS (3)
GLASS SHADE
CLAMPS (3)
7.5
ROTATE SHADE CLAMPS (3)
Tighten the three glass assembly screws to secure the
assembly (Figure 26).
INSTALL THE
NO LIGHT
COVER
Figure 26
16
GLASS ASSEMBLY
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 17
8. Wall Control Procedures
8.1
8.2
Your Emerson Ceiling Fan/Light Control consists of wall
mounted transmitter and a receiver which is mounted
under the fan ceiling cover. The remote control is
designed to separately control your ceiling fan speed
and light intensity.
Preset Memory Feature: Your Emerson receiver is
equipped with a preset memory feature. If the AC
supply to the receiver is powered through a wall switch,
when the switch is turned OFF, the control will
remember the light intensity and fan speed. When the
switch is turned back ON the light and fan will resume
operation as they were prior to the switch being turned
OFF.
Code switches in the transmitter and receiver may be
set in 32 different positions. If your fan and light go on
and off without using your control, you may be getting
interference from other remote units such as garage
door openers, car alarms or security systems. To
remedy this situations, simply change the combination
code in your transmitter and receiver.
8.3
WALL CONTROL
CODE SWITCHES
Your wall control has code switches which must be set
in one of 32 possible code combinations (Figure 27).
The five levers (numbered 1, 2, 3, 4, and 5) on the
switches are factory-set in the ON (up) position.
Change the switch settings as follows:
ON
1
2
3
4 5
I
8.4
Slide the five switch levers in the wall control to your
choice of ON (up) or down positions. Use a ball-point
pen or small screwdriver and slide the levers firmly up
or down.
8.5
CODE
SWITCHES
The sixth switch marked ON and I is for dimming
control of lights: Set switch to ON to allow for dimming
of the lights. Set switch to I for no dimming of the lights
such as for fluorescent bulbs and non-dimming CFLs.
WALL
CONTROL
Figure 27
17
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 18
8. Wall Control Procedures (continued)
SINGLE-POLE INSTALLATION
WARNING
!
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan, light kit or receiver.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse or circuit breaker box before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
NOTE: Make all wiring connections using wire
connectors (supplied). Make sure that all
connections are tight, including ground, and that no
bare wire is visible at the wire connectors, except
for the ground wire.
HOT
8.6
SW605 FAN/LIGHT
WALL CONTROL
BLK
Disconnect electrical power to the branch circuit at the
circuit breaker or fuse box before attempting to install
the ceiling fan wall control into the outlet box.
BLACK
ON
LOAD
8.7
BLACK
OFF
NEUTRAL
Remove faceplate and screws from existing wall control.
Pull control out from the wall box. Determine the “hot”
wire and the “load” wire and disconnect these wires
from control (Figure 28). Do not attempt to disconnect
any wires not already connected to existing control.
GROUND
RECEIVER LOCATED IN THE CEILING COVER
OF THE CEILING FAN
Figure 28
8.8
8.12
Before installing wall control, place wall control in “OFF”
mode by pushing “ON/OFF” switch to the “OFF”
position.
The wall control is supplied with a white, ivory, and
almond color switch covers. Choose the finish that best
suits your needs and snap the cover onto the wall
control (Figure 29).
8.9
8.13
Connect one black wire of wall control to the “hot” wire.
Securely connect wires with wire connectors supplied
(Figure 29).
Install decorator wall plate using the two screws
provided with wall plate. Leave wall control in “OFF”
mode until fan installation is completed (Figure 29).
8.10
Connect one black wire of wall switch to the “load”
(black) wire in wall box. Securely connect wires with
wire connector supplied.
!
WARNING
Do not connect any neutral (white) wire to this control.
Incorrect wiring will damage this control.
8.11
Screw wall control into wall box using the supplied
screws. Leave wall control in “OFF” mode until fan
installation is completed.
SW605 FAN/LIGHT
WALL CONTROL
SCREWS (2)
K
BL
WARNING
HOT
TO
120
VAC SO
URCE
O LOA
D
T
Check to see that all connections are tight and that no
bare wires are visible at the wire connectors.
OFF
ON
SWITCH COVER
BL
K
AC
GR
O
!
WALL BOX
UN
D
NEUTRAL
WIRES
DECORATIVE WALL PLATE
Figure 29
18
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 19
8. Wall Control Procedures (continued)
3-WAY INSTALLATION
HOT
BLK
OFF
WARNING
BLACK
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse or circuit breaker box before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
NEUTRAL
OFF
BLK
!
ON
SW605
FAN/LIGHT
WALL
CONTROL
TRAVELER
WIRE
ON
BLK
(One fan controlled by two different wall controls)
(See Figures 30 and 31.)
LOAD
BLACK
GROUND
RECEIVER LOCATED WITHIN THE CEILING
COVER OF THE CEILING FAN
8.14
Disconnect electrical power to the branch circuit at the
circuit breaker or fuse box before attempting to install
the ceiling fan wall control into the outlet box.
Figure 30
8.15
At all wall box locations remove faceplates and screws
from existing controls. Pull controls out from wall boxes
and determine which wall box contains the “hot” lead
and which wall box contains the “load” wire. Also,
identify traveler wires which are common to both wall
boxes. Disconnect wires from existing controls only. Do
not attempt to disconnect any wires not already
connected to existing controls.
8.16
Before installing wall control, place wall control in “OFF”
mode by pushing “ON/OFF” switch to the “OFF”
position.
88.17
Install a wall control in the wall box containing the “hot”
wire first. Connect the black wire of the wall control to
the “hot” wire. Securely connect wires with wire
connectors supplied.
8.18
Connect one black wire of the wall control to both
remaining traveler wires in the wall box and secure with
wire connector supplied.
19
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 20
8. Wall Control Procedures (continued)
3-WAY WIRING DIAGRAM:
NEW CONSTRUCTION
STANDARD WIRING FOR EXISTING
3-WAY CONTROLS
NOTE: Retrofit 3-way installations are likely to
include two traveler wires between the two wall
boxes. In new construction, only one traveler wire Is
required (See Figure 31).
BLK
BLACK
!
EXISTING
WALL CONTROL
HOT
WARNING
Check to see that all connections are tight and that no
bare wires are visible at the wire connectors.
TRAVELER WIRES
LOAD
8.19
3-WAY WIRING DIAGRAM: RETROFIT
Screw wall control into wall box using the supplied
screws. Leave wall control in “OFF” mode until fan
installation is completed.
HOT
BLK
OFF
The wall control is supplied with a white, ivory, and
almond color switch covers. Choose the finish that best
suits your needs and snap the cover onto the wall
control (Figure 31).
BLK
ON
SW605
FAN/LIGHT
WALL
CONTROL
OFF
TRAVELER
WIRES
ON
SW605
FAN/LIGHT
WALL
CONTROL
BLACK
8.20
BLK
BLK
LOAD
Figure 31
8.21
Next, install the other wall control into the wall box
containing the load wire. Connect the black wire of the
wall control to the traveler wire(s) already connected to
the black wire (in the other wall box). Secure with wire
connectors supplied.
8.22
Connect one black wire of the wall control to the “load”
(black) wire and secure with wire connector supplied.
8.23
Connect one black wire of the wall control to both
remaining traveler wires in the wall box and secure with
wire connector supplied.
20
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 21
8. Wall Control Procedures (continued)
IMPORTANT: Do not interrupt the conditioning until
the fan comes to a complete stop in approximately
5 minutes. All functions of the control will be
rejected during conditioning.
PROGRAMMING THE RECEIVER
OPERATING FREQUENCY & HIGH SPEED
CONDITIONING OF FAN CONTROL
IMPORTANT: Ceiling fan blades MUST be installed
before high speed conditioning can begin.
8.26
8.24
High speed conditioning is now complete.
Within 1 minute of restoring electricity to the ceiling fan,
push and hold the fan OFF button (
) for 3 to 5
seconds to set the code in the receiver. The ceiling fan
lights (if installed) will blink to indicate the transmitted
has been paired with the receiver.
8.27
If programming is unsuccessful, retry the above
instructions after cycling the wall control ON/OFF switch
to restart the 1 minute programming time period.
IMPORTANT: Immediately after successful pairing,
the ceiling fan will automatically begin high speed
conditioning of the motor. During conditioning, the
electronic motor control software is calculating
speeds for the 2nd through 5th speed settings
based on the blades that were installed on the fan.
8.28
If still unsuccessful, shut off the electricity at the fuse
box or breaker panel and change the wall control
frequency (Page 17). After changing the frequency
settings, repeat instruction #1 of this section within one
minute of restoring the electricity.
8.25
The fan will run for approximately 2 minutes in the
upward direction then reverse direction to down flow
and run an additional 2 minutes. When conditioning is
complete, the fan will come to complete stop.
21
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 22
8. Wall Control Procedures (continued)
USING YOUR CEILING FAN
!
WARNING
POWER
INDICATOR
LIGHT
Fan installation must be completed, including the
installation of the fan blades, before testing the remote
control.
LIGHT
INTENSITY
BUTTONS
AIRFLOW
DIRECTION
Your wall control has full control of your fan and light
(Figure 32).
NOTE: Prior to operation of the fan and light from
the wall control, set the fan speed to HIGH (....) and
turn the light ON (
).
FAN SPEED
BUTTONS
POWER
BUTTON
OFF
ON
ON/OFF SWITCH
O = OFF / — = ON
8.29
To set the desired fan speed, press the ( ) button to
decrease the speed and the ( ) to increase the speed.
The LED display will light up to indicate the new speed
selected
Figure 32
8.30
To turn the downlight on, press and release the (
)
button. The light will turn on at the light intensity
previously selected. To change the intensity hold the
button down. The intensity will go up and down while
the button is held. Release the button at the desired
intensity.
8.31
To turn the uplight on, press and release the (
)
button. The light will turn on at the light intensity
previously selected. The intensity will go up and down
while the button is held. Release the button at the
desired intensity.
8.32
If airflow is desired in the opposite direction, press the
(
) button on the wall control. The fan must be
operating at any speed for the reverse button to
function. The blades will turn in the opposite direction
and reverse the airflow.
8.33
Your wall control comes complete with your choice of
three wall cover plates; ivory, white and light almond.
8.34
Your fan is now wired to be turned on and off from the
fan switch.
22
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 23
9. Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
!
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
10. Accessories
Ceiling Fan/Light Controls (see store or catalog).
!
Downrod Extension Kits (see store or catalog).
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
WARNING
The use of any other control not specifically approved
for this fan could result in fire, shock and personal
injury.
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
23
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 24
11. Repair Parts
1
17
2
10
3
15
16
4
19
17
18
18
19
18
5
19
16
23
15
6
17
20
20
21
7
22
8
23
21
24
9
25
26
22
11
13
12
OFF
ON
14
24
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 25
11. Repair Parts Listing
Model Numbers
Key
No.
Description
*
1
2
3
Hanger Ball Assembly, Consisting of:
Hanger Bracket
Hanger Ball
Downrod (4.5”)
4
5
6
7
8
9
10
11
12
13
14
Ceiling Cover (1)
Coupler Cover (1)
Fan Motor Assembly (1)
Fan Blades (set of 5)
Fan Blade Flanges (set of 5)
Light Kit Assembly (1)
50-Watt Halogen Bulbs (2)
Glass Assembly (1)
No Light Cover (1)
Receiver (1)
Wall Control, 6-Speed LED (1)
*
15
16
17
18
19
20
23
24
25
26
Parts Bag Containing:
Pin, Clevis (1)
Clip, Hairpin (1)
Threaded Stud, #8 - 32 x 1-1/4” (4)
Lockwasher, External Tooth #8 (4)
Knurled Knob, #8 - 32 (4)
Screw, #10-32 x 1/4” Washer Head
Blade (16)
Screw, 1/4-20 x 3/8” Pan Head
with Lockwashers (21)
Screw, 1/4-20 x 3/8” Oval Head
with Lockwasher (spare)
Setscrew (1)
Wrench, Setscrew (1)
Wire Connector (5)
Blade Balance Kit (1)
—
Owner's Manual
21
22
CF4900BS00
CF4900ORB00
CF4900VS00
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
RCK55
SW605
RCK55
SW605
RCK55
SW605
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
BP7485
BP7485
BP7485
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
25
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 26
12. Trouble Shooting
!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE
TROUBLE SHOOTING YOUR FAN.
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit
breakers.
2. Loose power line connections to the fan,
or loose switch wire connections in the
switch housing.
2. Check line wire connections to fan and switch
wire connections in the switch housing.
!
3. Reversing switch in neutral position.
3. Make sure reversing switch position is all the
way to one side.
2. Fan sounds noisy. 1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Loose screws in motor housing.
2. Check to make sure all screws in motor housing
are snug (not over-tight).
3. Wire connectors inside switch housing
rattling.
3. Check to make sure wire connectors in switch
housing are not rattling against each other or
against the interior wall of the switch housing.
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is turned OFF.
WARNING: Make sure main power is turned OFF.
4. Screws holding blades to flywheel
are loose.
4. Tighten screws securely.
1. Setscrew in motor coupling is loose.
1. Tighten both setscrews securely in the motor
coupling.
2. Setscrew in hanger ball/downrod
assembly is loose.
2. Tighten the setscrew in the hanger ball/
downrod assembly.
3. Screws securing fan blades to
flywheel are loose.
3. Check to be sure screws which attach the fan
blades to the motor are tight.
4. Hanger bracket and/or ceiling outlet
box is not securely fastened.
4. Tighten the hanger bracket screws to the outlet
box, and/or secure outlet box.
5. Fan blades out of balance.
5. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
13. Remote Control Trouble Shooting
Fan/Light Fails to Operate
Short Range
• Check that the speed switch on the fan is set to
( ) or ( ) speed.
• Check that the light switch is on.
• Check that the battery is good (blue indicator light
should light when any button is pressed).
• Check that the receiver is wired properly.
• Check that code switches in the remote control and
receiver are set in the same position.
• If the remote control operates the fan when close to
it, but does not operate it at a distance of 40 feet, try
placing the antenna wire outside of the ceiling cover.
26
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 27
Emerson Air Comfort Ceiling Fan Limited Warranty
What The Limited Warranty Covers:
This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original
retail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and
accessories of the Emerson Ceiling Fan against all defects in workmanship and materials.
What The Period Of Coverage Is:
This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner's
Manual or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are covered
by this limited warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE OR
PROVINCE SHALL COVER THE MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TO
COMPONENTS AND ACCESSORIES.
No Other Express or Implied Warranty Applies:
THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILING
FAN, AND ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE,
WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED OR
MANUFACTURED FOR YOUR USE OR PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THE
ONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIME
OF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROM
STATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
What We Will Do To Correct Problems:
If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during
the expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or
workmanship, you must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defective
motor, component or other accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and no
replacement Emerson Ceiling Fan can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or the
replacement Emerson Ceiling Fan to you at no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan.
How You Can Receive Warranty Service:
You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You can
return your Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at 1-800-237-6511 to obtain a return authorization and service
identification tag. In order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have that
information readily available when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call Emerson
Customer Service, prior to your call please be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your return
authorization request, we will provide you with a postage paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed at
the end of this limited warranty. The return label will be sent to the mailing address you provide to us by phone.
What Is Not Covered:
This limited warranty does not extend to and expressly excludes:
• The glass globes and light bulbs of your Emerson Ceiling Fan,
• Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship,
• Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center,
use of parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse,
modifications or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession,
• Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual.
This limited warranty is deemed null and void upon the occurrence of either of the following events:
• You cease to own the Emerson Ceiling Fan product, or
• The Emerson Ceiling Fan is moved from its original point of installation.
This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent,
dealer or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co.
Limitation of Liability
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BY
LAW, IN NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILING
FAN OR FOR THE NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN
PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,
NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANY
INDIVIDUAL USING THE EMERSON CEILING FAN EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequential
damages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or
equipment.
How State and Provincial Law Relates To The Warranty:
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
27
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF4900
BP7485 Southtowne CF4900
12/4/13
10:15 AM
Page 28
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., Eastern, Monday-Friday
1-800-654-3545
www.emersonfans.com
Retain this manual for future use.
Part No. F40BP74850000
Revision: 131201
Printed in China
12/13
Form No. BP7485
U.L. Model No.: CF4900