advertisement
OWNER'S
HANDBOOK
MINI COUNTRYMAN
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
ONE
Cooper
Cooper S
Cooper S ALL4
Congratulations on your new MINI
One D
COOPER D
Cooper D All4
Cooper SD
Cooper SD All4
© 2011 Bayerische Motoren Werke
Aktiengesellschaft
Munich, Germany
Not to be reproduced, wholly or in part, without written permission from BMW AG, Munich.
English II/11
Printed on environmentally friendly paper, bleached without chlorine, suitable for recycling.
CONTENTS
The quickest access to a particular topic or item is by consulting the detailed alphabetical index, see page
.
Notes
General information
OVERVIEW
Driving area
Radio MINI CD
Radio MINI Boost CD
CONTROLS
Opening and closing
Adjusting
Child safety
Driving
Everything under control
Technical features for driving comfort and safety
Lights
Climate
Practical interior equipment
DRIVING HINTS
Driving precautions
Entertainment
Radio MINI CD
Radio MINI Boost CD
COMMUNICATION
Telephone
MOBILITY
Refuelling
Wheels and tyres
In the engine compartment
Maintenance
General care
Replacing parts
Mutual aid
Indicator and warning lights
REFERENCE
Technical data
Maintenance overview
From A to Z
4
Notes General information
General information
About this Owner's
Handbook
We have tried to make all the information in this
Owner's Handbook easy to find. The quickest way to access a specific topic or item is by consulting the detailed alphabetical index at the end. Consult the first chapter for an overview of your car.
When the time comes to sell your MINI, remember to hand over this Owner's Handbook; it is an important part of the vehicle.
Additional sources of information
If you have any queries, your MINI Service Centre will be glad to advise you.
You can find additional MINI-related information, for example on the engineering features, in the Internet by visiting www.MINI.com.
Symbols used
Indicates precautions that must be followed precisely in order to avoid the possibility of personal injury and serious damage to the vehicle.
<
Indicates information that will assist you in gaining the optimum benefit from your vehicle and enable you to care more effectively for your vehicle.
<
Refers to measures that can be taken to help protect the environment.
<
< Marks the end of a specific item of information.
* Identifies optional extras or specific nationalmarket items of equipment, as well as equipment and functions not yet available at the time of printing.
Symbol for components and assemblies
Recommends that you study the relevant section of this Owner's Handbook in connection with a particular part or assembly.
Your car
Your MINI is manufactured by Bayerische
Motoren Werke Aktiengesellschaft, BMW AG.
When you ordered your MINI, you chose various items of equipment. This Owner's Handbook describes all models and equipment specifications which the manufacturer of your MINI offers within this particular model line.
This explains why the Owner's Handbook may also contain details of items which you have not ordered. The differences can easily be identified by the asterisk * shown against optional extras.
If your MINI features equipment not described in this Owner's Handbook, observe the enclosed
Supplementary Owner's Handbooks.
In vehicles with right-hand drive, some of the controls are arranged differently from those shown in the illustrations of this Owner's
Handbook.
<
Built-date*
The production date of your vehicle can be found at the bottom of the door column of the driver door.
The 'built-date' is defined as 'the calendar month and the calendar year in which the body shell and the powertrain subassemblies are conjoined and the vehicle is driven or moved from the production line'.
General information
Notes
Status at time of printing
The high safety and quality standards of MINI vehicles are guaranteed by continuous development. In rare instances, your vehicle may therefore differ from the information supplied in the
Owner's Handbook.
For your safety
Your vehicle is configured for the operating conditions and registration requirements of your country. If the vehicle is to be operated in another country, your vehicle must be adapted to any prevailing different operating conditions and permit requirements.
Information on possible exclusion of warranty or warranty restrictions for your vehicle can be obtained from your MINI Service Centre.
For customers in Australia/New Zealand
As you read this manual, please bear the following in mind: to ensure that our vehicles continue to embody the highest quality and safety standards, we at MINI pursue a policy of continuous, ongoing development. Because modifications in the design of both vehicles and accessories may be introduced at any time, your own vehicle's equipment may vary from that described in this manual. For the same reason, it is also impossible to guarantee that all descriptions will be completely accurate in all respects.
We must therefore request your understanding of the fact that we are unable to recognise legal claims based on discrepancies between the data, illustrations and descriptions in this manual and your own vehicle's equipment. Please note, too, that some of the optional equipment described in this manual is not available on Australian models due to restrictions imposed by
Australian Design Rules and other requirements.
If you have any queries, your Service Centre will be glad to advise you.
For your safety
Maintenance and repair
The advanced technology behind this vehicle, for example the use of modern materials and high-performance electronics, means that specially adapted methods of maintenance and repair are required. You should therefore have the work this involves carried out only by a MINI Service Centre or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI. If such work is performed inexpertly, it could result in consequential damage and thus constitute a safety risk.
<
Parts and accessories
The manufacturer of your MINI recommends using parts and accessory products for the car which the manufacturer of your MINI has approved for this purpose.
MINI Service is the correct source for genuine
MINI parts and accessories, other products approved by the manufacturer of your MINI, and competent advice on all related matters.
These parts and products have been tested by the manufacturer of your MINI for their safety and functional compatibility with MINI vehicles.
The manufacturer of your MINI accepts product liability for them.
Conversely, the manufacturer of your MINI cannot accept liability for parts or accessory products of any kind which it has not approved.
The manufacturer of your MINI is unable to assess each individual product of outside origin as to its suitability for use on MINI vehicles without safety risk. This suitability cannot be guaranteed even if an official permit has been issued for the particular product in a specific country.
Tests performed for such permits cannot always cover all operating conditions for MINI vehicles, and some of them therefore are insufficient.
<
5
Watch Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW Driving area
Driving area
Around the steering wheel: Controls and displays
1 Adjusting outside mirrors, folding in and out *
2
Low-beam headlights
Automatic driving lights control *
Adaptive Head Light *
8
Flashing turn indicators
High-beam headlights
Parking lights *
Computer *
Driving area
OVERVIEW
3 Revolution counter
Resetting trip distance recorder 58
10 Unlocking the engine compartment
Right-hand drive vehicles: front passenger side
4
Wipers
5 Switching the ignition on/off and starting/stopping the engine
7 Buttons * on steering wheel
Resuming cruise control
On the right:
Memorising speed and accelerating or decelerating
On the left:
Turn volume up or down
Activating/deactivating cruise control *
Telephone * :
Accept and end a call, start dialling * for selected phone numbers, and redial if no phone number is selected
Activating/deactivating voice control system *
Changing radio stations
Selecting music tracks
Scrolling in the redial list
8 Horn, entire surface
9 Adjusting the steering wheel
Headlight beam throw adjustment
9
OVERVIEW
Displays
Driving area
1 Revolution counter
with indicator and warning lights
2 Display for
> Current vehicle speed
> Indicator and warning lights
3 Resetting trip distance recorder
4 Display for
> Position of automatic transmission
> Computer *
> Date of next scheduled service, and remaining driving distance
> Distance recorder – odometer –
> Initialising the Run Flat Indicator *
> Settings and information
>
> Gearshift point display
6 Speedometer
with indicator and warning lights 11
7 Fuel gauge
10
Indicator and warning lights
Principle
Driving area
OVERVIEW
Indicator and warning lights can come on in various combinations and colours in panel 1 or 2.
Some lights in the panel are checked for proper functioning and thus light up briefly when the engine starts or the ignition is switched on.
What to do in the event of a fault
A list of all indicator and warning lights, as well as notes on the possible cause of a fault and on what corresponding measures should be taken, can be found starting on page
11
OVERVIEW Driving area
Around the centre console
12
Driving area
OVERVIEW
1 Microphone for voice control system * and hands-free mode for telephone *
2 Indicator/warning light * for front passenger airbags
3
Reading lights
Ambient lighting *
Glass roof, electric *
Rear window heating
Windscreen heating *
Air volume
8 Switch panel in the centre console
Seat heating
Window lift, front
Window lift, rear
4 Hazard warning flashers
6 Radio/CD
7 Air conditioning or automatic air conditioning
Temperature
Rear fog light
Recirculated-air mode
Air distribution for air conditioner
Air distribution to the windscreen *
Air distribution to the upper body area *
Air distribution to the footwell *
Automatic air distribution and flow rate control *
Maximum cooling *
Cooling function
Defrosting windows *
9 Buttons in the centre console
Fog lights
Rear fog lamp
Safety switch for electric window
SPORT button *
Automatic start/stop function *
Driving stability control systems
Dynamic Stability Control DSC 69
Dynamic Traction Control
DTC *
USB audio interface *
13
OVERVIEW
Radio MINI CD
Radio MINI CD
1 On/off, setting volume
2 Setting values, setting time
3 Selecting stations manually
4 Sampling station/title manually
5 Selecting saved stations
6 Display
7 Selecting wavelength range/memory range
8 Selecting audio source
9 TP, traffic programme *
10 Selecting a station/track
11 Radio Data System RDS
14
12 Setting values
13 Calling up settings
14 CD drive
15 CD ejection
Radio MINI Boost CD
Radio MINI Boost CD
OVERVIEW
1 Selecting audio sources
2 On/Off * , volume adjustment
3 Calling up settings
> Speed-related volume
> Sound adjustment
4 Function buttons for confirming the menu items displayed above
5 Changing station, track
> Changing stations
> Changing track with CD player
6 Display
7 Selecting functions
> Turn: select menu item or value
> Press: confirm selection or save settings
8 Set up/end voice connections
9 Access settings menu
10 Select frequency manually
11 CD drive
12 Eject CD
15
OVERVIEW Radio MINI Boost CD
Menu guidance
Functions of radio and telephone * can be accessed via the buttons on the radio and menus.
Access settings menu
Press the MENU button for:
> Settings
> MINI call numbers
> Telephone *
Accessing audio menu
Press the MODE button for:
> Radio
> Digital radio *
> CD player
> External audio device, e.g. MP3 player
> USB audio interface *
Selecting a menu item
Menu items can be selected via the right-hand knob or function buttons.
Via the right-hand knob
1.
Turn knob, arrow 2, to mark menu item, e.g.
"CONFIG".
To execute a displayed function, press the button underneath and on the left or right of it.
If only one function is displayed, press button in centre.
Presentation in the Owner's Handbook
Function buttons that can be pressed on the left or the right, are equipped with an arrow on the respective side.
E.g. press the button on the left.
Menu items that should be selected are displayed in inverted commas, e.g. "CONFIG".
Symbols on display
Symbol Function
Function is selected
Function is activated.
Function is deactivated.
Quit menu, one menu back
Display other menu items
Scroll display, list contains more than 2 entries
Change to higher level directory
2.
Press the knob, arrow 1, to confirm a highlighted function.
Via function buttons
Press the button.
16
Radio MINI Boost CD
OVERVIEW
17
Handle Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
CONTROLS Opening and closing
Opening and closing
Key/remote control
Buttons of remote control
Integrated key
1 Open back hatch
2 Releasing
3 Engaging
General
Every remote control contains a rechargeable battery that is recharged when it is in the ignition lock while the car is being driven. Use the remote control key at least twice a year to maintain the battery charge. If your car is fitted with convenient access * , the remote control contains a replaceable battery, page
If several remote controls are used, different settings are called up and made in the vehicle, depending on which remote control is recog-
nised when it is unlocked, see Personal Profile
on page
In addition, information about service require-
ments is stored in the remote control, see Service data in the remote control, page 151 .
New remote controls
Your MINI Service Centre can supply new remote controls, as additional units or as replacements in the event of loss.
Press the button 1 to release the key.
The integrated key fits the following locks:
> Key switch * for front passenger airbags,
.
> Driver's door, page
Personal Profile
Principle
Many MINI functions can be adjusted to individual needs. With the help of Personal Profile, most of these settings are stored for the remote control currently in use. When you unlock the car the remote control is recognised and the settings stored for it are called up and implemented.
This means that your settings will be activated for you, even if in the meantime your vehicle was used by someone else with another remote control and the corresponding settings.
A maximum of three remote controls for three different people can be adapted. A requirement is that each person uses his or her own remote control.
Personal Profile settings
See the pages indicated for more detailed information about the settings.
20
Opening and closing
CONTROLS
> Response of the central locking system
>
Automatic locking of the vehicle 25
>
> Settings for the displays in the speedometer and revolution counter:
>
12h/24h mode of the clock, see Formats and units of measure 61
>
Date format, see Formats and units of measure 61
> Units of measure for fuel consumption, distance covered/remaining range, and
temperature, see Formats and units of measure 61
> Light settings:
> Headlight courtesy delay feature
> Daytime driving lights
> Automatic air-conditioning system * : activating/deactivating AUTO programme, cooling function, adjusting temperature, air flow
> Entertainment:
> Adjusting volume, from page
>
Central locking system
The principle
The central locking becomes active when the driver's door is closed.
The following are unlocked or locked in combination:
> Doors
> Tailgate
> Fuel filler flap
Operating from outside
> Via the remote control
> Via the door lock *
> With convenient access * by means of the handles on the driver's and the front passenger's door
In addition, if the remote control is used, the welcome lights and the interior light are switched on or off. The alarm system * is also armed or disarmed, page
Operating from inside
Button for central locking, page
.
In the event of a sufficiently severe accident, the central locking system unlocks automatically.
The hazard warning flashers and the interior light are in addition switched on.
Opening and closing: from the outside
Persons remaining in the vehicle or pets left inside can lock the doors from the inside. You should therefore take the key with you, so that the car can be opened from the outside.
<
With the remote control
Releasing
Press the button.
Welcome lights and interior light come on.
Characteristics during unlocking
The way in which the car is unlocked can also be set. The setting is stored for the remote control in use.
21
CONTROLS Opening and closing
1.
Switch on the ignition, see page 46
.
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
5.
Keep the button pressed until the display changes.
6.
Press the button repeatedly until the indicated symbol, arrow, appears.
8.
Press button to select:
>
Pressing the the driver's door. button only unlocks
Press it twice to unlock the entire vehicle.
>
Press the button once to unlock the entire vehicle.
9.
Keep the button pressed until the display changes. The setting is stored for the remote control currently in use.
Convenient opening
Hold the button pressed.
The electric windows are opened and the glass roof * is raised.
Convenient closing via the remote control is not possible.
<
Engaging
Press the button.
Do not lock the vehicle from the outside when there is someone inside it, as some national-market versions as well as versions with certain optional equipment cannot then be unlocked from the inside.
<
Setting confirmation signals
To have confirmation signals sound when the vehicle is locked or unlocked.
1.
Switch on the ignition, see page
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
7.
Keep the button pressed until the display changes.
22
Opening and closing
CONTROLS
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
5.
Keep the button pressed until the display changes.
6.
Press button to select, arrow:
> Confirmation signal when the vehicle is unlocked
> Confirmation signal when the vehicle is locked
Switching on the interior light
When the vehicle is locked:
Press the button.
This function also enables you to locate the car, for instance in a parking garage.
Unlocking the tailgate
Press release.
button approx. 1 second and then
On certain national-market versions, the tailgate cannot be unlocked unless the car has been unlocked.
In order to avoid damage, make sure there is sufficient clearance in all directions before opening the tailgate.
If the tailgate had been locked before it was opened, it is locked again as soon as it is closed.
Before and after each trip, check that the tailgate has not been inadvertently unlocked.
<
Malfunctions
The remote control may malfunction as a result of interference from localised radio signals. If this occurs, unlock and lock the car at the door lock with the integrated key.
If the vehicle can no longer be locked with a remote control, the battery in the remote control is flat. Use this remote control when driving a relatively long distance to recharge its battery,
.
Via the door lock
7.
Keep the button pressed until the display changes.
8.
Press button to select:
>
The hazard warning flashers come on while the vehicle is being unlocked/ locked.
>
The function is deactivated.
9.
Keep the button pressed until the display changes. The setting is stored.
Setting the way in which the vehicle is unlocked,
.
23
CONTROLS Opening and closing
Do not lock the vehicle from the outside when there is someone inside it, as some national-market versions as well as versions with certain optional equipment cannot then be unlocked from the inside.
<
In some national-market versions, the alarm system * is triggered when the car is unlocked via the door lock.
To end the alarm:
Unlock the car with the remote control, page
or insert the key fully into the ignition lock.
<
Alarm system, see page
Without alarm system * or convenient access * only the driver's door is locked via the door lock.
<
To lock all doors, fuel filler flaps and luggage compartment lids together:
> For closed doors with an inside button for central locking in the passenger compart-
, lock the vehicle.
> Unlock and open the driver's side or front passenger door, page
Lock the vehicle.
> Lock the driver's door via the door lock with the integrated key or
> Press down the locking button on the front passenger's door and close the door from outside.
Convenient opening and closing
The alarm system * or convenient access * can be used to operate side window and glass sunroof * through the door lock.
Opening/closing
Hold the key in the position for unlocking or locking.
Watch the closing movement to ensure that no one is trapped. The movement is stopped when the key is released.
<
Manual operation
In the event of an electrical fault, the driver's door can be locked or unlocked by turning the integrated key to the limit positions in the door lock.
Opening and closing: from the inside
The switch locks or unlocks the doors, tailgate and fuel filler flap * when the doors are closed, but does not deadlock them.
Unlocking and opening
> Either unlock the doors together using the central locking switch and then pull the door handle above the armrest or
> Pull the handle on each individual door twice: the first time to unlock the door, and the second time to open it.
Locking
> Press the switch or
> press down the safety lock button of a door.
To prevent that you are shut out of the car accidentally, the driver's door cannot be locked with the safety lock button when it is open.
Persons remaining in the vehicle or pets left inside can lock the doors from the inside. You should therefore take the key with you, so that the car can be opened from the outside.
<
24
Opening and closing
CONTROLS
Automatic locking*
The situations in which the vehicle is locked can also be programmed. The setting is stored for the remote control in use.
1.
Switch on the ignition, see page
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
7.
Keep the button pressed until the display changes.
8.
Press button to select:
>
The central locking is engaged automatically after a brief moment if no door has been opened.
>
The central locking is engaged automatically as soon as you drive off.
> or
The central locking is engaged automatically after a brief moment if no door has been opened or as soon as you drive off.
>
The central locking system remains unlocked.
9.
Keep the button pressed until the display changes. The setting is stored.
5.
Keep the button pressed until the display changes.
6.
Press the button repeatedly until the indicated symbol, arrow, appears.
Tailgate
In order to avoid damage, make sure there is sufficient clearance in all directions before opening the tailgate.
<
Opening
On certain national-market versions, the tailgate can only be unlocked with the remote control after the car has been unlocked.
Only drive with the tailgate completely closed, as otherwise the rear lights are covered and road safety is impaired.
<
Press the top of the MINI badge, arrow, or
25
CONTROLS Opening and closing
Press and hold down the button on the remote control This will unlock the tailgate.
Closing
To avoid injuries, ensure that the closing area of the tailgate is unobstructed.
<
Recessed handles in the tailgate lining make it easier to pull the tailgate down.
Alarm system*
Principle
The alarm system will respond if:
> A door, the engine compartment or the tailgate are opened
> There is movement inside the car
> The vehicle's inclination changes, for instance if an attempt is made to jack it up and steal the wheels or to raise it prior to towing away
> There is an interruption in the power supply from the battery
Depending on the national-market version of the car, the alarm system briefly indicates unauthorised entry or tampering by means of:
> Audible alarm
> Switching on the hazard warning flashers
> Flashing the high-beam headlight
Arming and disarming
Whenever the car is locked or unlocked, the alarm system is armed or disarmed.
Even when the alarm system is armed, you can open the tailgate by means of the button on the remote control, page
sequently close the luggage compartment lid, it is again locked and monitored.
Opening certain national-market versions via the door lock triggers the alarm.
<
Panic mode*
In the event of danger, the alarm system can be triggered.
Press the button for at least two seconds.
To switch off the alarm:
Press any button.
Switching off an alarm
> Unlock the car with the remote control,
.
> Insert the key fully into the ignition lock.
> With convenient access * and the remote control, press the button on the door lock.
Display on the revolution counter
When the system is armed, all LEDs pulse in the rhythm of a heartbeat. After approx. 16 minutes one LED flashes.
> LEDs pulse or LED flashes:
System is armed.
> One LED flashes at short intervals: the doors, engine compartment lid or tailgate are not properly closed.
Even if these are not closed fully, the remaining items are deadlocked and the
LEDs pulse after approx. 10 seconds for
26
Opening and closing
CONTROLS approx. 16 minutes. Afterwards, one LED flashes. The interior movement detector is not activated.
> LEDs go out after the vehicle is unlocked:
No attempt was made to tamper with the car.
> LEDs flash after unlocking until the key is inserted in the ignition, but for no longer than approx. 5 minutes:
An attempt was made to tamper with the car.
Tilt alarm sensor
The vehicle's inclination is monitored. The alarm will be triggered for instance if an attempt is made to steal the vehicle's wheels or tow it away.
Interior movement detector
Before the interior movement detector can operate correctly, the windows and glass roof must be closed * .
Avoiding false alarms
The tilt alarm sensor and the interior movement detector can be switched off together. This prevents false alarms, e.g. in the following situations:
> In duplex garages
> When being transported on vehicle-carrying trains, boats/ships or trailers
> If pets are to remain inside the vehicle
Switching off the tilt alarm sensor and interior movement detector
> Press the button on the remote control twice in succession.
> Lock the vehicle twice with the integrated key.
LEDs flash in short succession for approx.
2 seconds. The tilt alarm sensor and interior movement detector are switched off until the next time the vehicle is unlocked and locked.
Convenient access*
Convenient access enables you to access the car without having to take the remote control into your hand. It is sufficient to have the remote control on your person, for example in a jacket pocket. The vehicle automatically recognises the remote control when it is in the immediate vicinity or inside the car.
Operating requirements
> The car or the tailgate can be locked only when the car ascertains that the remote control on your person is not inside the car.
> About two seconds have to elapse before the car can again be unlocked and locked.
> The engine can be started only when the car ascertains that the remote control is inside the car.
> The doors and tailgate must be closed in order to operate the windows and the glass roof * .
Convenient access supports the following functions:
> Unlocking/locking the vehicle
> Comfort closing
> Unlock tailgate individually
> Starting the engine
Comparison to the conventional remote control
Generally speaking, it makes no difference whether you control the functions outlined above by using convenient access or by pressing the buttons on the remote control.
Instructions for opening and closing begin on
.
The features specific to convenient access are described below.
A short delay when opening or closing windows or the glass roof indicates that a test is being carried out to ascertain whether
27
CONTROLS Opening and closing there is a remote control inside the car. If necessary, repeat the opening or closing operation.
<
Unlocking
Press the button 1.
Dependent upon the setting, see Characteristics during unlocking on page 21 , either only the
driver's door or the entire vehicle is unlocked.
Press the button again to lock the vehicle again.
<
If a remote control is detected inside the passenger compartment after the car has been unlocked, the electric steering wheel lock disen-
.
Convenience opening with the remote control,
.
Locking
Press the button 1.
Press and hold down the button 1 for convenient closing.
The windows and the glass roof * are also closed.
Separate unlocking of the tailgate
Press the top of the MINI badge.
If a remote control inadvertently left behind is detected inside the locked vehicle's luggage area after you close the tailgate, the tailgate reopens slightly. The hazard warning flashers flash and an acoustic signal * sounds.
<
Windows and glass roof, electric*
You can operate the windows and roof while the engine is switched off as long as no one opens a door or the tailgate.
If the door or tailgate is closed again and the remote control is detected inside the vehicle, the windows or the roof can be operated again.
Insert the remote control into the ignition lock in order to operate the windows or roof while the engine is switched off and the doors are open.
Switching on radio readiness
Switch on radio readiness by pressing the start/ stop button, page
Do not depress the brake or clutch, otherwise the engine will start.
<
Starting the engine
The engine can be started or the ignition can be switched on when a remote control is inside the vehicle. It is not necessary to insert the remote
control in the ignition lock, page 46
.
Switching off the engine in vehicles with automatic transmission
The engine can be switched off only when the
selector lever is in position P, page 48
.
To switch off the engine with the selector lever in position N, the remote control must be in the ignition lock.
Before driving a vehicle with automatic transmission into a car wash
1.
Insert the remote control into the ignition lock.
2.
Depress the brake.
3.
Move the selector lever to position N.
4.
Switch off the engine.
The car will be able to roll.
Malfunction
Comfort access may malfunction as a result of interference from local radio signals.
28
Opening and closing
CONTROLS
In this case, open or close the vehicle using the buttons on the remote control or with the integrated key.
Insert the remote control into the ignition lock in order to start the engine.
Warning lights
Warning light comes on when you attempt to start the engine: engine starting not possible. The remote control is not inside the vehicle or is faulty. Bring the remote control inside the vehicle or have it checked. Try inserting a different remote control in the ignition lock.
Warning light comes on while the engine is running: the remote control is no longer inside the vehicle. If the engine is switched off, it can be restarted only within approx. 10 seconds.
Indicator light comes on: change the battery in the remote control.
Changing the battery
The battery in the remote control for comfort access requires replacement from time to time.
1.
Remove the cover.
2.
Insert a new battery with the plus side up.
3.
Press the cover back into position.
Dispose of the old battery only at an authorised collecting point or hand it in to your MINI Service Centre.
<
Glass roof, electric*
Observe the glass roof during the closing procedure, to avoid any injuries.
Take the key with you when you leave the car, otherwise children could operate the roof and possibly injure themselves.
<
Raising
> Press the switch backwards to the pressure point and hold it there.
Both glass roofs are raised.
The movement is stopped when the switch is released.
> Press the switch towards the rear beyond the pressure point while the ignition is switched on.
Both closed glass roofs are fully raised.
Pressing the switch again stops the movement.
Opening, closing
> In the raised position, press the switch backwards to the pressure point and hold it there.
The front glass roof is opened.
The rear glass roof is closed.
The movement is stopped when the switch is released.
> In the raised position and while the ignition is switched on, push the switch backwards beyond the pressure point.
The front glass roof opens fully.
The rear glass roof is closed.
Pressing the switch again stops the movement.
29
CONTROLS Opening and closing
In the same manner, the glass roof is closed by pushing the switch forwards.
The front glass roof remains in the raised position. The rear glass roof is raised. Pushing the switch again closes both roofs fully.
Convenient operation via remote control, door
lock or convenient access, page 22
,
Roller sunblind
The roller sunblind can be opened or closed separately from the glass roof.
After switching off the ignition
The roof can still be operated for approx.
1 minute while the ignition is switched off as long as no door is opened.
After a power failure
After a power failure, it is possible that the roof will only move to the raised position. Then have the system initialised. The manufacturer of your
MINI recommends having this work carried out by your MINI Service Centre.
Opening, closing
Front windows
> Press the switch downwards.
The window opens until the switch is released.
> Tap the switch downwards.
The window opens automatically as soon as radio standby is active. Tap the switch again to halt the opening movement.
In the same manner, the glass roof is closed by pushing the switch upwards.
Rear windows
Windows
Watch the windows during the closing action to avoid injuries.
Take remote control with you when you leave the car, otherwise children could operate the electric windows and possibly injure themselves.
<
If a window can only be closed after it has been opened and closed several times in short succession, the system has overheated.
Let the system cool down for several minutes while the ignition is switched on or the engine is running.
<
> Press the switch downwards.
The window opens until the switch is released.
> Tap the switch downwards.
The window opens automatically as soon as radio standby is active. Tap the switch again to halt the opening movement.
In the same manner, the glass roof is closed by pushing the switch upwards.
30
Opening and closing
CONTROLS
After switching off the ignition
The windows can still be operated for approx.
1 minute while the ignition is switched off as long as no door is opened.
Take the key with you when you leave the car, otherwise children could operate the electric windows and possibly injure themselves.
<
Trap protection
If the closing force of a window exceeds a specific value as it closes, the closing action is interrupted and the window reopens slightly.
Despite the trap protection function, make sure that the windows are not obstructed as they close; if this precaution is not taken, the risk remains that thin objects, for instance, could fail to interrupt the closing movement.
Do not install any accessories in the movement range of the windows in order not to impair the trap protection function.
<
Closing without the trap protection function
In case of an external hazard, or if ice cover, for example, does not allow you to close a window normally, the window can be closed manually.
1.
Push the switch upward and hold it there.
The trap protection function is restricted and the window opens slightly when the closing force exceeds a certain value.
2.
Within approx. 4 seconds, push the switch upward again and hold it there. The window closes without the trap protection function.
Safety switch
This prevents the rear windows being opened and closed using the switches in the rear seat area, for instance by children.
Press the button indicated by the arrow.
The LED lights up when the safety function is switched on.
Press the safety switch when carrying children on the rear seat, otherwise careless closing of the windows could result in injury.
<
31
CONTROLS Adjusting
Adjusting
Safe seated position
A seated position that suitably reflects your requirements is a vital condition of relaxed driving with a minimum of fatigue. In conjunction with the seat belts, the head restraints and the airbags, the seated position has a major influence on your safety in the event of an accident.
You should therefore observe the following notes in order to maintain the protective function of the vehicle's safety systems.
For additional notes on child safety, see page
Airbags
Keep your distance from the airbags.
Always grip the steering wheel on the rim, with your hands in the 3 o'clock and 9 o'clock positions, to minimise the risk of injury to the hands or arms in the event of the airbag being triggered off.
No other persons, pets or objects should be held or permitted to remain between the airbag and yourself.
Do not use the front airbag cover on the front passenger's side as a tray. Make sure that the front passenger adopts a correct seated position, e.g. does not rest feet or legs on the instrument panel; otherwise he/she could sustain leg injuries in the event of the front airbag being triggered.
Make sure that passengers keep their head away from the side airbag and do not lean on the covers of the head-level airbags, otherwise they may sustain injuries in the event of the airbags being triggered.
<
Even if all these instructions are complied with, certain injuries as a result of contact with the airbag cannot be entirely ruled out, depending on the circumstances in which an accident occurs.
Occupants with sensitive hearing may be subject to brief and generally temporary impaired hearing caused by the ignition and inflation noise.
The locations of the airbags and additional notes
.
Head restraint
Head restraints adjusted to the correct height reduce the risk of injuries to the neck in the event of an accident.
Adjust the head restraint in such a way that its centre is at approximately ear level; otherwise, there is an increased risk of injury should an accident occur.
<
.
Seat belt
All occupants should always fasten their seat belts before you set off. The airbags are a complementary safety feature and not a substitute for the seat belts.
Number of seat belts
For your safety and that of your passengers, the car is fitted with four or five * seat belts.
However, they can offer protection only when used correctly.
Adjustment for automatic retracting seat belts
> Draw the buckle tongue attached to the seat belt across the body and press it into the buckle catch until a 'click' is heard.
> Adjustment of the belt length is very important. To adjust the lap belt and check whether the buckle has locked correctly, pull upwards on the shoulder strap until the lap belt fits tightly.
> The length of the diagonal shoulder strap adjusts itself automatically to allow freedom of movement.
32
Adjusting
CONTROLS
> To release the seat belt, press the button on the buckle catch unit.
Never restrain more than one person with each seat belt. Babies or small children must not travel on the lap of another occupant.
Around the pelvis, make sure that the belt sits firmly on the hips and does not press down on the stomach. The seat belt must not be worn touching the neck, pass over sharp edges or hard or fragile objects, or become trapped at any point. Pull the seat belt tight and without twisting across the pelvis and shoulder and keep it as close as possible to the body in order to avoid it slipping over the hips and injuring the stomach in the event of a frontal collision. Avoid wearing bulky clothing and regularly pull the belt in the upper-body area taut, otherwise its restraining effect could be impaired.
<
.
Forward/back
Pull lever, arrow 1, and slide seat into the desired position, arrow 2.
After letting go of the lever, move the seat gently forwards and backwards so that it properly locks into place.
Height
Seats
Note before adjusting
Do not reposition the driver's seat while the car is in motion. The seat could move unexpectedly, leading to the driver losing control of the vehicle, and possibly resulting in an accident.
Do not recline the driver's or front passenger's seat back too far, otherwise there will be a risk of sliding under the seat belt in an accident, so that the belt loses its protective effect.
<
Comply with the instructions on head restraint height on page
on page
Seat adjustment front
risk.
<
Failure to comply with the notes on page
33 may put your personal safety at
Repeatedly pull the lever upwards or push it downwards, arrow 1, until the desired height is reached.
Seat back
Pull lever, arrow 1, and load or unload the backrest as required.
33
CONTROLS Adjusting
Lumbar support*
The seat back contour can be altered to provide more support to the curved, lumbar section of the spine.
The upper edge of the pelvis and the spinal column are supported, to encourage an upright but relaxed seated position.
Turn the wheel to increase or decrease the curvature.
Seat adjustment rear
Do not adjust the rear seats whilst the vehicle is in motion, otherwise there is a risk of injury to its occupants.
Make sure that the catches on the rear seats engage properly after they have been adjusted.
Otherwise the restraining effect of the seat belts could be impaired in the event of an accident.
<
Forward/back
Seat back
Adjusting the backrest angle, see page 95
.
Head restraints
Correctly adjusted head restraint
Head restraints adjusted to the correct height reduce the risk of injuries to the neck in the event of an accident.
Adjust the head restraint to the correct height at each occupied seats, otherwise there is an increased risk of injury in the event of an accident.
<
Height
Set the head restraint to the height at which the midway line is approximately level with the seat occupant's ears.
Adjusting height
Up: pull.
Down: press the button, arrow 1, and slide the head restraint down.
Removing
Only remove the head restraint if no one will be sitting on the seat in question.
1.
Pull the lever up and slide the seat to the preferred position.
2.
Release the lever and move the seat forward or back slightly so that it engages.
34
Adjusting
Refit the head restraint before driving with passengers, otherwise there is no protective function.
<
Seat heating*
CONTROLS
Front
1.
Pull up all the way.
2.
Fold the backrest back slightly.
3.
Press the button 1 and pull the head restraint out as far as it will go.
4.
In addition, use a suitable tool to press the button 2 and pull the head restraint fully out.
5.
Fold back the backrest.
Rear
1.
Pull up all the way.
2.
Fold the backrest forward slightly.
3.
Press the button 1 and pull the head restraint fully out.
4.
In addition, use a suitable tool to press the button 2 and pull the head restraint fully out.
5.
Fold up the rear seat backrest.
Switching on
Press once per temperature stage.
Three LEDs indicate the highest temperature.
If you continue driving within 15 minutes, the seat heating is automatically activated at the previously set temperature.
The temperature is reduced, if necessary including switching the heating off, to save the battery.
The LEDs remain lit.
Switching off
Press and do not immediately release the button.
Seat belts
Comply with the instructions on page 33
, or there will be greater risks to personal safety.
<
Seat belts are designed to bear upon the bony structure of the body and should be worn low across the front of the pelvis, or the pelvis, chest and shoulders, as applicable. Wearing the lap section of the belt across the abdominal area must be avoided.
Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed. A slack belt will greatly reduce the protection afforded to the wearer. Care should be taken to avoid contamination of the webbing by pol-
35
CONTROLS Adjusting ishes, oils and chemicals and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged. Belts should not be worn with straps twisted.
Each seat belt assembly must only be used by one occupant; it is forbidden to put a belt around a child being carried on the occupant's lap.
It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious.
<
No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack.
<
Before driving off, always make sure that all occupants have fastened their seat belts. The airbags are a complementary safety feature and not a substitute for the seat belts.
Front and rear seats
Height adjustment for seat belt latches, rear
If no passengers are being carried on the outer rear seats, the seat belt latches can be pushed back as far as the luggage compartment trim panel in order to avoid noise.
Rear seat: centre seat belt*
Belt mounting in the roof lining
The mounting for the seat belt is located in the roof lining.
1 Opening for belt
2 Mounting for large seat belt latch
3 Mounting for small seat belt latch
Take the small seat belt latch out of the mounting 3. Pull both seat belt latches down.
Closing
Fastening
The seat belt buckle must be heard to engage.
The upper belt anchorage is suitable for adults of any stature as long as they are sitting correctly, page
Opening
1.
Hold onto the belt.
2.
Press the red button on the belt buckle.
3.
Guide the belt back up to the reel.
Insert the belt and small seat belt latch 2 into the small belt buckle 3.
To open, press the red button on the small belt buckle 3 with seat belt latch 1.
36
Adjusting
CONTROLS
Fastening the belt
5 mph, if the front passenger's seat belt has not been fastened, if there are objects on the front passenger seat, or if the driver or front passenger unfasten their seat belts.
Damaged seat belts
In the event of stress due to an accident or damage: replace the belt system, including the seat-belt tensioner, and have the belt anchorage checked. Have this work performed only by your MINI Service Centre or by a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI, otherwise correct operation of these safety systems is not ensured.
<
1 Large seat belt latch
2 Small seat belt latch
3 Small belt buckle
4 Large belt buckle
Insert the seat belt latch 1 into the belt buckle 4.
The seat belt latch must be heard to engage in the belt buckle.
Insert the seat belt latch into the belt buckle so that when a passenger is fastened in, the belt rests against his body and is not twisted.
<
'Fasten seat belts' reminder for driver's seat and front passenger seat*
Front seats
The indicator light comes on and an audible signal sounds.Check whether the seat belt has been fastened correctly.
The 'Fasten seat belts' reminder is issued whenever the driver's seat belt has not been fastened.
The 'Fasten seat belts' reminder is also activated at road speeds above approx. 8 km/h, approx.
Mirrors
Outside mirrors
The outer section of the driver's side mirror shows a larger field of vision * than the inner section. In this way, the view to the rear is extended and the blind spot, as it is known, is reduced in size.
Objects reflected in the mirror are closer than they appear. Do not gauge your distance from following traffic based on what you see in the mirror; otherwise there is an increased risk of accident.
<
1 Adjusting the left or right outside mirror
2 Folding mirrors in and out *
37
CONTROLS Adjusting
Adjusting manually
The mirrors can also be adjusted manually: by pressing the mirror glass at its edges.
Folding mirrors in and out*
Turn the knob beyond the pressure point in direction 2. The mirrors can be folded in at road speeds up to approx. 30 km/h, approx. 20 mph.
This can be useful in narrow streets, for instance, or to fold the mirrors back out into their correct positions after they were folded in manually.
Automatic heating*
When the engine is running or the ignition is switched on, the automatic heating for both exterior mirrors will be switched on when the outside temperature reaches a certain level.
Interior mirror
Interior and exterior mirrors, automaticdim*
Two photosensors control the mirrors:
> In the interior mirror, arrow.
> One on the rear of the mirror
To ensure trouble-free operation:
> Keep the photosensors clean.
> Do not cover the area between the interior mirror and the windscreen.
> Do not attach any labels or stickers to the windscreen directly in front of the mirror
To reduce the risk of being blinded from behind while driving at night:
Turn the knob.
Steering wheel
Adjusting
Do not adjust the steering wheel position while the vehicle is in motion, or an accident may result from any unexpected movement.
<
1.
Fold the lever down.
2.
Move the steering wheel to the preferred height and angle to suit your seated position.
38
3.
Fold the lever back up.
Do not use force to swing the lever back up; otherwise the mechanism will be damaged.
<
Electric steering lock*
The steering wheel locks or unlocks automatically when the key is removed or inserted.
In cars with convenient access * , the steering wheel locks or unlocks automatically when the vehicle is locked or when the remote control is detected inside the vehicle.
Adjusting
CONTROLS
39
CONTROLS Child safety
Child safety
Important considerations
Do not leave children unattended in the vehicle, as they could otherwise endanger themselves and/or other persons by opening the doors, for example.
<
Not for Australia/New Zealand:
The front passenger seat and the outer rear seats of your MINI are suitable for the installation of universal child restraint systems for all age groups, providing these have been approved for the age group in question.
Always carry children at the rear
Accident research has shown that the safest place for children is on the rear seat.
Children under 12 years of age or smaller than 150 cm, approx. 5 feet, should always travel on the rear seats and in suitable child restraint systems, otherwise there is a greater risk of injury in the event of an accident.
<
Your MINI Service Centre will be glad to provide advice on the selection of suitable child restraint systems.
Not for Australia/New Zealand:
Exception for the front passenger seat
Seat height
Only fit universal child restraint systems if the seat height can be adjusted. Otherwise it will be impossible to optimise the position of the seat belt and to secure the child restraint system adequately.
<
Front passenger airbags
If you nevertheless need to fit a child restraint system on the front passenger's seat, the front and side airbags must be deactivated, otherwise a child travelling on that seat will face an increased risk of injury if the airbags are triggered off, even if a child restraint system is used.
<
Front passenger airbags can only be deactivated with the key switch for front passenger airbags.
<
Keyswitch* for front passenger airbags
You can deactivate and subsequently reactivate the front and side airbags for the front passenger by means of a keyswitch. This is located on the front passenger side of the instrument panel.
The front passenger airbags can only be deactivated and reactivated when the vehicle is stationary and with the front passenger's door open.
Deactivating
Use the integrated key to turn the key switch to the OFF position.
The airbags for the front passenger are deactivated when the switch is in this position. The airbags for the driver remain fully active.
Once the child restraint system has been removed, immediately reactivate the air-
40
Child safety
CONTROLS bags for the front passenger so that they can deploy correctly in the event of an accident.
<
Reactivating
Use the integrated key to turn the keyswitch to the ON position.
The front passenger airbags are reactivated and can deploy correctly if the need arises.
Functional status
> The indicator light remains on if the front passenger's airbags have been deactivated.
> The indicator light does not come on if the front passenger airbags have been activated.
As of radio readiness, page
light comes on briefly.
Child restraint systems, installation
Your MINI Service Centre can supply suitable child restraint systems for every age or weight group.
Before fitting a child restraint system to the outer rear seats, move the seats as far back as they will go.
5-seater: adjust the angle of the centre backrest so that it is the same as that of the outer backrests.
Once you have fitted the child restraint system to one of the outer rear seats, move the backrest forward if necessary so that it just makes contact with the child restraint system, see Rear seat
.
For selecting, installing and using child restraint systems, observe the manufacturer's instructions, otherwise the protective effect could be impaired.
Following an accident, have all components of the child restraint system and the seat belt that was used to secure it checked and renewed if necessary. Have this work carried out only by
MINI Service or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI.
<
For Australia/New Zealand: installation of child restraint systems
Since your car is equipped with a front airbag system for the front passenger's seat, the following warning is applicable:
We advise against using any type of child restraint system on the front passenger's seat.
Extreme Hazard
Never use rear facing child restraint systems on a seat which is protected by an airbag fitted directly in front of it, otherwise there is an increased risk of injury should the airbag deploy.
<
Not for Australia/New Zealand: on the front passenger's seat
Before fitting a child restraint system to the front passenger's seat, make sure that the front and side airbags for the front passenger are deactivated, otherwise there is an increased risk of injury should the airbags deploy.
<
Seat position
Before installing a universal child restraint system, move the front passenger seat into the rearmost and most upright * position to achieve the best possible positioning of the seat belt. Do
41
CONTROLS Child safety not adjust the position of seat with the child restraint system fitted.
Not for Australia/New
Zealand: child seat mountings, ISOFIX
When you are fitting and using ISOFIX child seats, comply with the operating and safety instructions provided by the manufacturer of the system, as otherwise the protective effect can be diminished.
<
Correct ISOFIX child restraint systems
The following ISOFIX child restraint systems can be used on the specified seats in your vehicle.
The corresponding classes are indicated on the child seats themselves.
Rear seats
A - ISO / F3
B - ISO / F2
B1 - ISO / F2X
C - ISO / R3
D - ISO / R2
E - ISO / R1
The mountings for the lower ISOFIX anchorages are at the points marked by the arrows.
Make sure that the two lower ISOFIX anchors are correctly locked and that the child restraint system is positioned fully against the backrest, otherwise its protective function may be impaired.
<
Mounting point for upper ISOFIX retaining strap
Use the attachment points for the upper
ISOFIX retaining strap only for securing child restraint systems, otherwise the attachment points could be damaged.
<
Depending on the size of the child restraint system, if necessary slide the headrest upwards and adjust the longitudinal setting of the front seat,
.
Brackets for lower ISOFIX mountings
Before fitting the child seat, pull the belt away from the area around the child seat mountings.
For ISOFIX child restraint systems with an upper retaining strap there are two additional mounting points, arrows.
Positioning the upper ISOFIX retaining strap
Make sure that the upper retaining strap does not pass over sharp edges and is not twisted on its path to the upper mounting point.
Otherwise the child restraint system cannot protect the child as intended in the event of an accident.
<
42
Child safety
CONTROLS
AS 1754 – can be attached directly to corresponding anchor fitting.
Please refer strictly to the installation instructions supplied with the child restraint system.
Child restraint anchor fittings
1 Direction of travel
2 Head restraint
3 Luggage area floor
4 Hook for the upper retaining strap
5 Mounting point
6 Seat back
7 Upper retaining strap of the child restraint system
Clipping the upper retaining strap onto the mounting point
1.
Push the head restraint upwards.
2.
Guide the upper retaining strap between the head restraint posts.
3.
Use the hook to clip the upper retaining strap onto the mounting point.
4.
Push the head restraint into its lowermost position.
5.
Pull the retaining strap taut.
The child restraint anchor fittings, see arrows, are located behind the back of the rear seats.
Routing the strap
Do not route the strap of the child restraint system over the head rest or over sharp edges and do not twist the strap, as otherwise the protective effect of the child restraint system is not given.
<
For Australia/New
Zealand:
Child restraint systems
4-Seater
In accordance with ADR 34/01, provisions have been made to allow installation of a child restraint system at both outer seating positions in the rear.
The attaching clip which is part of the upper anchorage strap of a child restraint system –
1 Forward driving direction
2 Head rest
3 Load area floor
4 Attaching clip
5 Child restraint anchor fitting
6 Seat back
7 Strap of the child restraint system
43
CONTROLS Child safety
Clipping the upper retaining strap onto the mounting point
Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances they are to be used for adult seat belts, harnesses or for attaching other items or equipment to the vehicle.
<
1.
Lift the head rest.
2.
Pass the strap of the child restraint system between the head rest and the seat back and also between the two supports of the head rest.
3.
Hook in the attaching clip into the anchor fitting.
4.
Readjust the head rest into the lowest possible position.
5.
Tighten the strap of the child restraint system.
5-Seater
In accordance with ADR 34/01, provisions have been made to allow installation of a child restraint system at both outer seating positions in the rear.
The attaching clip which is part of the upper anchorage strap of a child restraint system –
AS 1754 – can be attached directly to corresponding anchor fitting.
Please refer strictly to the installation instructions supplied with the child restraint system.
Child restraint anchor fittings
The child restraint anchor fittings for the two outer seats, see arrows, are located behind the back of the rear seats.
The child restraint anchor fitting for the centre seat is located under the luggage-compartment sill, position 4 in picture centre seat.
Routing the strap
Do not route the strap of the child restraint system over the head rest or over sharp edges and do not twist the strap, as otherwise the protective effect of the child restraint system is not given.
<
Outer seats:
1 Forward driving direction
2 Head rest
3 Load area floor
4 Attaching clip
5 Child restraint anchor fitting
6 Seat back
7 Strap of the child restraint system
44
Centre seat:
Child safety
CONTROLS
Securing doors and windows
Rear doors
1 Forward driving direction
2 Head rest
3 Attaching clip
4 Child restraint anchor fitting
5 Load area floor
6 Seat back
7 Strap of the child restraint system
Clipping the upper retaining strap onto the mounting point
Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances they are to be used for adult seat belts, harnesses or for attaching other items or equipment to the vehicle.
<
1.
Lift the head rest.
2.
Centre seat: fold the load area floor backwards
3.
Pass the strap of the child restraint system between the head rest and the seat back and also between the two supports of the head rest.
4.
Hook in the attaching clip into the anchor fitting.
5.
Readjust the head rest into the lowest possible position.
6.
Tighten the strap of the child restraint system.
Push down the locking lever on the rear doors.
The door in question can now only be opened from the outside.
Safety switch for window lifts
The rear window lifts are locked and cannot be operated by the occupants of the rear seats.
Press the safety switch, see page
45
CONTROLS Driving
Driving
Ignition lock
Inserting the key in the ignition lock
Start/stop button
Insert the key fully into the ignition lock.
> Radio readiness
Individual electrical consumers can operate.
> The electric steering wheel lock * disengages audibly.
Insert the key into the ignition lock before you move the vehicle, otherwise the electric steering-wheel lock will not disengage and you will not be able to steer the car.
<
Convenient access*
The electrical steering-wheel lock disengages automatically when the remote control is detected in the passenger compartment.
Removing the key from the ignition lock
Press the key in briefly; it is ejected a short way.
At the same time:
> The ignition is switched off, if it was on beforehand.
> The electric steering wheel lock audibly.
* engages
Automatic transmission
You cannot take out the key unless the selector lever is in the P position: interlock.
Press the start/stop button to switch radio readiness or the ignition on and off. In doing so, do not depress the brake or clutch.
The engine starts when you press the start/stop button and depress the brake if the car has automatic transmission, or the clutch if the car has a manual gearbox.
<
Radio readiness
Individual electrical consumers can operate. The time and outside temperature are displayed in the revolution counter.
Radio readiness is switched off automatically:
> When the key is removed from the ignition lock
> In cars with convenient access * , by pressing the button on the door handle or the button on the remote control, see
> After a certain period of time
Ignition on
Most indicator and warning lights in panel 1, page
, come on for various lengths of time.
When the engine is switched off, switch off the ignition and all electrical consumers you are not using in order to preserve the battery.
<
46
Driving
CONTROLS
Radio readiness and ignition off
All indicator lights and warning lights in the displays go out.
The ignition is switched off automatically if the driver's door is opened. It is switched back on by pressing the start/stop button again.
The ignition is not switched off for example in the following situations:
> Clutch or brake depressed
> Low-beam headlights are on
> Automatic start/stop function * activated
Starting the engine
Never run the engine in enclosed spaces, as inhaling the harmful exhaust gas can lead to loss of consciousness with fatal consequences. The exhaust gas contains carbon monoxide, which is colourless and odourless, but highly toxic. Do not leave the car unattended with the engine running, as this constitutes a hazard.
Before leaving the car with the engine running, place the gearbox in idle or move the selector lever to position P and fully apply the handbrake to prevent the car from moving.
<
Avoid starting, stopping and restarting the engine in rapid succession or repeated attempts to start the engine if it does not fire, otherwise unburned or only partially combusted fuel could reach the catalytic converter, which could overheat and sustain damage as a result.
<
Do not warm up the engine with the car at a standstill; it is preferable to set off straight away, driving at moderate engine speeds.
Do not press the accelerator pedal while starting the engine.
Manual gearbox
Key in the ignition lock or, with convenient access, in the vehicle, see page
1.
Depress the brake.
2.
Depress the clutch.
3.
Press the start/stop button.
Automatic transmission*
Key in the ignition lock or, with convenient access, in the vehicle, see page
1.
Depress the brake.
2.
Move selector lever in position P or N.
3.
Press the start/stop button.
Starting proceeds automatically for a certain time, and ceases automatically as soon as the engine has fired.
Diesel engine
When the engine is cold and the temperature falls below approx. 0 6/327, starting may be somewhat delayed by automatic preheating.
The preheat indicator light in the revolution counter comes on.
Stopping the engine
Always take the key with you when you leave the vehicle.
When parking on an incline, fully apply the handbrake, otherwise the car could begin to roll.
<
47
CONTROLS Driving
Manual gearbox
1.
With the car at a standstill, press the start/ stop button.
2.
Engage first gear or reverse.
3.
Fully apply the handbrake.
Automatic transmission*
1.
With the car at a standstill, move the selector lever to position P.
2.
Press the start/stop button.
3.
Fully apply the handbrake.
Before entering the car wash
The vehicle will be able to roll if you observe the following steps:
1.
Insert master key with remote control into ignition lock, even if vehicle is equipped with convenient access.
2.
Depress the brake.
3.
Move the selector lever to position N.
4.
Switch off the engine.
Automatic start/stop function*
The principle
The automatic start/stop function helps to save fuel and reduce emissions. For this purpose, the system switches the engine off during a stop, for example in a traffic queue or at traffic lights, the ignition remains on. As soon as you depress the clutch, the engine starts.
Automatic mode
After every engine start, the automatic start/ stop function is active and on standby.
Stopping the engine
1.
Move the vehicle forwards at a speed of at least 5 km/h, approx. 3 mph, to activate the function.
2.
Shift to neutral when coasting to a stop, for example at a traffic light, or when the vehicle is stationary.
3.
Release the clutch.
With the vehicle stationary, the engine is switched off automatically and the indicator light lights up.
The air flow rate of the air conditioner/automatic air-conditioning system is reduced.
Engine is not switched off
Before the engine is switched off, the system checks whether certain conditions related to safety and comfort have been met.
In the following situations, the engine is not switched off:
> Outside temperature below approx. +3 6/
37 7
> Inside of vehicle in heat-up or cool-down phase
> High outside temperature and operation of the air conditioner
> Engine not yet at operating temperature
> Battery severely depleted, see Vehicle battery on page
> After reversing
> Driver's seat belt not fastened
Starting the engine
With the gear lever in the idle position, depress the clutch.
The engine is started and the indicator light goes out.
Engine starts automatically
The shut-down engine starts automatically, for example in the following cases:
48
Driving
CONTROLS
> The inside of the vehicle heats up strongly and the air conditioner is switched on
> Severely depleted battery, see Vehicle battery on page
> Low brake partial vacuum, for example due to depressing the brake a number of times in succession
> The vehicle moves off
Safety function
The engine is not started automatically if the driver's seat belt or the engine compartment lid is opened after the engine has been shut down automatically. The indicator light lights up. The engine can only be started using the start/stop button.
Deactivating manually
Handbrake
The handbrake is primarily intended to prevent a stationary car from rolling away; it acts on the rear wheels.
Applying
The lever engages automatically.
Releasing
Press the button.
The LED lights up.
With the system disabled, the engine can only be stopped and started using the start/stop button.
Activating manually
Press the button again.
The LED goes out.
Malfunction
The automatic start/stop function no longer switches the engine off automatically. The indicator light lights up. You can continue your journey. Have the system checked.
<
Raise slightly, press the knob and move the lever down.
In exceptional cases, if the handbrake has to be used to slow or stop the car, do not pull the lever up too hard. Keep the knob on the lever held in all the time.
Otherwise, excessive application of the handbrake can cause the rear axle to be overbraked and the rear of the car to swerve as a result.
<
Manual gearbox
When shifting in the 5th/6th gear plane, press the shift lever to the right. Otherwise the engine could be damaged if you inadvertently shift into 3rd or 4th gear.
<
49
CONTROLS Driving
Reverse
Engage this gear only when the vehicle is standing still. When the gearshift lever is pressed to the left, a slight resistance has to be overcome.
Automatic transmission* with Steptronic
In addition to the fully automatic mode, you can perform manual gearshifts with the Steptronic, page
Stopping the car
Before leaving the car with the engine running, move the selector lever to position P and apply the handbrake to prevent the car from moving.
<
Removing the key
To remove the key from the ignition lock, move the selector lever to position P and switch off the engine: interlock. Removing the key from the ignition lock, see page
.
Selector lever positions
P R N D M/S + –
Displays in the revolution counter
Changing selector lever positions
> The selector lever can only be moved out of position P with the ignition switched on or the engine running:
> Before moving the lever away from P or N with the vehicle stationary, first depress the brake, otherwise the selector lever will refuse to move: shiftlock.
Apply the brake until you are ready to move off; this will prevent the vehicle creeping when a gear is selected.
<
A lock prevents the selector lever from accidentally being moved to the R or P positions.
Overriding the lock
P R N D DS M1 to M6
The selector lever position is displayed, or the current gear in the manual mode.
Press the button on the front of the selector lever, arrow.
P Park
Engage this gear only when the vehicle is standing still. The driven wheels are locked.
R Reverse
Engage this gear only when the vehicle is standing still.
N Neutral
Select in car wash, for example. The vehicle will be able to roll.
D Drive, automatic position
Use this position for all normal driving. All forward gears are selected automatically.
50
Driving
CONTROLS
Kick-down
Kick-down enables you to achieve maximum performance.
Press the accelerator pedal beyond the increased resistance at the full-throttle position.
Sport programme and M/S manual-shift mode
Shifting gears using the shift paddles on the steering wheel*
With the selector lever in automatic-drive position D, you can shift gears directly via the shift paddles on the steering wheel. The car automatically switches to manual mode.
If for a certain amount of time you neither shift gears using the shift paddles nor accelerate, the car automatically switches back to automaticdrive position D.
From position D, move the selector lever to the left into the M/S selection gate:
The Sport program is activated and DS appears.
This position is recommended for a performance-oriented driving style.
To deactivate the Sport programme or manual operation M/S, move the selector lever to the right into position D.
Shifting gears using the selector lever
Press the selector lever forwards or backwards to activate manual mode. Steptronic changes the gear.
> Pull the selector lever in the + direction.
Transmission shifts up.
> Press the selector lever in the – direction.
Transmission shifts down.
The selected gear, for example M1, is displayed in the revolution counter.
To return to the automatic mode, move the selector lever to the right into position D.
Upshifts and downshifts are performed only at a suitable engine or road speed; for example, the transmission will not shift down if the resulting engine speed would be too high. The gear selected is briefly shown, followed by the gear currently in use.
> Pull one of the two shift paddles.
Transmission shifts up.
> Press one of the two shift paddles.
Transmission shifts down.
M1 to M6 is displayed in the revolution counter.
Manually unlock selector lever interlock
The selector lever interlock can be overridden if the selector lever is stuck in position P, in spite of the ignition being switched on, the brake being depressed and the button on the selector lever being pressed:
51
CONTROLS Driving
1.
Unclip the gaiter of the selector lever.
2.
Pull the gaiter up over the selector lever until the gaiter is inside out. If necessary, unplug the cable connector.
3.
Insert the puller 1 into the loop on the passenger's side.
4.
Pull the strap upwards.
5.
To move the selector lever into the desired position, press the button on the front of the selector lever knob.
Before manually unlocking the selector lever interlock, strongly apply the handbrake to prevent the vehicle rolling away.
<
Unusually rapid flashing of the indicator light indicates that a flashing turn indicator bulb has failed.
<
Indicating a turn briefly
Press and hold the lever as far as the pressure point for as long as you wish to indicate a turn.
Triple turn signal
Press the lever as far as the pressure point.
It can be programmed whether the turn indicators flash once or three times.
1.
Switch on the ignition, see page
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
Flashing turn indicators/ headlight flasher
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
1 Flashing turn indicators
2 Headlight flasher
Indicating a turn
Press the lever beyond the pressure point.
To cancel it manually, press the lever as far as the pressure point.
52
5.
Keep the button pressed until the display changes.
Driving
CONTROLS
6.
Press the button repeatedly until the indicated symbol, arrow, appears.
7.
Keep the button pressed until the display changes.
8.
Press button to select:
>
Indicating a turn briefly.
>
Triple turn signal.
9.
Keep the button pressed until the display changes. The setting is stored.
Wiper system
The lever returns to the home position when released.
Normal wiper speed
Press once.
The wipers switch to intermittent wipe when the vehicle is stationary.
Fast wiper speed
Press twice or press beyond the pressure point.
The wipers switch to normal speed when the vehicle is stationary.
Intermittent wipe or rain sensor*
If the car is not fitted with a rain sensor, the intermittent-wipe time is a preset.
The rain sensor automatically regulates the windscreen wipers in accordance with the rain intensity. The rain sensor is located on the windscreen, directly in front of the interior mirror.
Activating intermittent operation or rain sensor
Press the button, arrow 3.
The symbol is displayed in the revolution counter.
Deactivate the rain sensor in an automatic vehicle wash, to prevent the vehicle's wipers being activated inadvertently and damaged.
<
1 Switching on wipers
2 Switching off wipers or flick-wipe
3 Activating/deactivating intermittent wipe or rain sensor *
4 Cleaning windscreen and headlights *
Switching on wipers
Press the lever upwards, arrow 1.
53
CONTROLS Driving
Adjusting rain sensor sensitivity
1.
Switch on the ignition, see page 46
.
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
5.
Keep the button pressed until the display changes.
Deactivating intermittent operation or rain sensor
Press the button again, arrow 3.
Flick wipe
Press the lever downwards once, arrow 2.
Cleaning windscreen and headlights*
Pull the lever, arrow 4.
Fluid from the washer fluid reservoir is sprayed on to the windscreen and the wipers are operated briefly.
When the vehicle's lights are switched on, the headlights are cleaned simultaneously at practical intervals.
In cars fitted with an alarm system, the headlights cannot be cleaned when the engine compartment lid is open.
Do not run the washer systems if the reservoir for washer fluid is empty, or the washer pump will be damaged.
Only use the washer systems if the engine compartment lid is completely locked. Otherwise the headlight cleaning system * could be damaged.
Only operate the washer systems and cleaning equipment if you are certain that the fluid will not freeze to the windscreen and interfere with the view ahead. Screenwash should therefore be added to the fluid.
<
Windscreen washer jets
The windscreen washer jets are heated automatically * while the engine is running or the ignition switched on.
6.
Press the button to select the desired sensitivity.
7.
Wait or keep the button pressed until the display changes.
The settings are stored.
54
Rear window wiper
Driving
CONTROLS there is a risk of fire and personal safety is endangered.
<
0 Rest position of the rear wiper
1 To switch on intermittent wipe :
Turn the end of the lever to position 1.
In reverse gear, continuous operation is activated.
The rear window washer does not move if the cap is in position 1 prior to the ignition being switched on.
Rear window washer
2 To clean the rear window with intermittent wipe :
Turn the cap to position 2 and hold it there.
3 To clean the rear window from the rest position :
Turn the cap to position 3 and hold it there.
Do not run the washer systems if the reservoir for washer fluid is empty, or the washer pump will be damaged.
<
Washer fluid
Screenwash for the washer fluid is highly flammable. Therefore, to avoid the risk of injury, it has to be kept away from ignition sources and stored only in the sealed original container out of the reach of children. Comply with the instructions on the container.
<
Washer fluid reservoir
Only top up washer fluid with anti-freeze protection when the engine has cooled down. This prevents contact with hot engine components. Otherwise, if the fluid is spilled,
When filling with water, to which screenwash has been added if required, always follow the manufacturer's instructions.
Mix the water and screenwash additive before filling the washer fluid reservoir, to make sure the correct concentration is maintained.
<
Capacity
Approx. 4 litres, approx. 7 pints.
Cruise control*
The principle
You can activate the cruise control from a speed of approx. 30 km/h or 20 mph. The car then memorises and maintains the speed that you specify using the button on the steering wheel.
Do not use the cruise control when unfavourable conditions preclude driving at steady speeds, for example winding roads, heavy traffic or a poor road surface such as snow, rain, ice, or loose material. Otherwise you could lose control of the vehicle and cause an accident as a result.
<
55
CONTROLS Driving
Activating
1 Resuming cruise control
2 Activating/deactivating cruise control
3 Maintaining speed, memorising speed, and accelerating
4 Maintaining speed, memorising speed, and decelerating
The indicator light in the speedometer comes on. The cruise control is on standby and can be activated.
Activating/deactivating cruise control
Press the button 2.
The system is automatically deactivated, during:
> braking
> gear changes
> in selector lever position N
> when the driving stability control system is intervening
Cruise control is not deactivated by pressing the accelerator pedal. Once the accelerator pedal is released, the memorised speed is regained and maintained.
The memorised speed is deleted when the ignition is switched off.
Maintaining current speed
Press the button 3.
The vehicle's current speed is maintained and memorised.
If engine braking alone is insufficient on a downhill gradient, the controlled speed may be exceeded. It may in turn prove impossible to
56 maintain speed on uphill gradients if current engine power output is insufficient.
Increasing speed
Press the button 3 repeatedly until the desired speed is reached. Each time the button is pressed, road speed is increased by approx.
2 km/h or approx. 1 mph.
Accelerating with the button
Hold button 3 down.
The vehicle accelerates without the accelerator pedal being touched. After you release the button, the speed the vehicle has reached will be maintained and memorised.
Reducing speed
Press button 4 repeatedly until the desired speed is reached.
Functions analogous to increasing speed or accelerating, except that the speed is decreased.
Calling up memorised speed
Press button 1.
The speed last memorised is regained and maintained.
The memorised speed is deleted when the ignition is switched off.
Display in the revolution counter*
The selected speed is displayed briefly.
If --- km/h (--- mph) appears temporarily in the revolution counter, it is possible that
the system prerequisites for operation have not been met.
<
Malfunction
The warning light comes on in the revolution counter when the system has failed.
Driving
CONTROLS
57
CONTROLS Everything under control
Everything under control
Revolution counter
Units of measure
To select the respective units of measure, km or miles for the odometer as well as 6 or 7 for the outside temperature, page
Fuel gauge
Never force engine speed up into the red warning field. In this zone the fuel supply is interrupted to protect the engine.
Displays in the revolution counter
1 Current vehicle speed
2 Odometer, trip distance recorder and outside temperature display *
3 Resetting trip distance recorder
Odometer and trip distance recorder
Resetting trip distance recorder
With the ignition switched on, press knob 3 in the revolution counter.
Fuel tank capacity
For notes on refuelling, see page
If the vehicle is at an angle for some time, for example on a long mountain road, the value in the display may fluctuate to some extent.
Approx. 47 litres, approx. 99 pints.
Reserve
When the reserve volume of approx. 8 litres, approx. 1.8 gal, is reached, the remaining LEDs switch from orange to red, arrow. The revolution counter shows the remaining range. Below a range of approx. 50 km, approx. 30 miles, a warning light comes on.
If the remaining range is below 50 km, approx. 30 miles, refuel the car, otherwise the engine's functions are not assured and damage may occur.
<
58
Everything under control
CONTROLS
Computer*
Displays in the revolution counter
Press the button on the flashing turn indicator lever to call up items of information one after the other.
The following items of information are displayed in the order listed:
> Range
> Average fuel consumption
> Current fuel consumption
> Average speed
> External temperature display
In parallel, gearshift recommendations to reduce fuel consumption can be displayed, see
Gearshift point display * on page
To set the corresponding units of measure, see
Formats and units of measure on page 61 .
Range
This display indicates how far the vehicle can probably be driven on the fuel remaining in the tank. The range is calculated on the basis of the way the car has been driven over the past
30 km, approx. 20 miles, and the amount of fuel currently in the tank.
If the range is below 50 km, approx.
30 miles, refuel the vehicle, otherwise the engine's functions are not assured and damage may occur.
<
Average fuel consumption
Calculated for the period since the engine was last started.
To reset the average consumption reading: press the button in the flashing turn indicator lever for approx. 2 seconds.
Current fuel consumption
Enables you to check how economical you are driving.
Average speed
The calculation of average speed ignores any stationary periods where the engine was switched off.
To reset the average speed reading: press the button in the flashing turn indicator lever for approx. 2 seconds.
Outside temperature warning
If the temperature reading falls to approx.
+3 6/377, a signal sounds and a warning light comes on. There is an increased risk of ice.
Sheet ice can also form at temperatures above +3 6/377. You should therefore drive carefully over bridges and shaded roads; otherwise there is an increased risk of accident.
<
Gearshift point display*
Principle
This system recommends the gear that allows optimal fuel economy in the current driving situation. Whenever that gear differs from the one currently engaged, you are prompted to shift up or down, respectively.
59
CONTROLS
Enabling/disabling the system
Everything under control
If the range is displayed in the computer, see page
59 , press the button on the flashing turn
indicator lever for approx. 3 seconds.
Displays
1 Button for:
> Selecting display
> Setting values
> Confirming selected display or set values
> Calling up computer information
Symbol Function
Setting rain sensor *
1 Gear with most favourable fuel consumption
2 Shift up to the displayed gear to enhance fuel economy
3 Shift down to the displayed gear to enhance fuel economy
In parallel, you can call up any information from the computer as usual.
Settings and information
Operating principle
Some settings and information can only be made or called up when the ignition is switched on, the vehicle is stationary and the doors are closed.
60
Calling up Check
Displaying vehicle
Initialising the Run Flat
Indicator
Symbol
Everything under control
Function
Setting formats and units of measure, resetting to factory settings 62
Exiting displays
CONTROLS
Adjusting settings
> Confirmation signals for locking and unlocking of
> Characteristics during
> Automatic
> Headlight courtesy delay
> Daytime driving lights
> Triple turn
Setting the clock *
1.
Press the button in the turn indicator lever repeatedly until "HOME" appears.
2.
Press and hold down the button.
The system also exits the displays if no entry is made within approx. 8 seconds.
Next setting or item of information
Setting the date
Exiting a menu
1.
Within a setting or item of information, press the button in the turn indicator lever repeatedly until "NEXT" appears.
2.
Press and hold down the button.
Direct switch to next setting or item of information.
Formats and units of measure
To set formats and units of measure. The settings are stored for the remote control in use,
see also Personal Profile on page 20 .
61
CONTROLS Everything under control
1.
Switch on the ignition, see page 46
.
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
5.
Keep the button pressed until the display changes.
6.
Press the button repeatedly until the indicated symbol, arrow, appears.
> Fuel consumption: l/100 km, mpg, km/l *
> Distance covered: km, mls
> Time * : 24h, 12h
> Date * : day.month dd.mm, month/day mm/dd
> Temperature: 6, 7
7.
Keep the button pressed until the display changes.
8.
Press the button in order to change the format or unit of measure
9.
Keep the button pressed until the display changes.
The settings are stored.
Resetting to factory settings
The settings for formats and units of measure can be reset to factory settings. The settings are stored for the remote control in use, see also
1.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
2.
Keep the button pressed until the display changes.
62
Everything under control
CONTROLS
3.
Press the button repeatedly until the symbol and "SET" appear.
The extent of service work required can be read out from the remote control by your
MINI Service Advisor.
<
Displaying vehicle check
For certain maintenance operations, you can view the respective distance remaining or due date individually in the revolution counter.
1.
Switch on the ignition, see page
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
4.
Keep the button pressed until the display changes.
5.
Press the button repeatedly until "RESET" is displayed.
6.
Press and hold down the button until the display switches to the first setting option.
The settings are reset.
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the corresponding symbol and "SERVICE-INFO" appear.
Next Service indicator
The remaining driving distance and the date of the next scheduled service are displayed briefly immediately after you start the engine or switch on the ignition.
5.
Keep the button pressed until the display changes.
6.
Press the button to display the individual service requirements, see below.
63
CONTROLS
Possible displays
Everything under control
Symbol Function
Brake fluid
Exiting a display
1 Button for selecting information
Symbol Function
Engine oil *
Next setting or item of information
Front brakes
Rear brakes
Roadworthiness test
More information on the MINI Maintenance Sys-
tem can be found on page 151 .
Clock
Setting the clock
Radio MINI CD:
To set the 12h/24h mode, see Formats and units of measure on page 61 .
1.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
Vehicle check
2.
Keep the button pressed until the display changes.
64
Everything under control
CONTROLS
3.
Press the button repeatedly until the symbol and "SET" appear.
1.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
4.
Keep the button pressed until the display changes.
5.
Press the button to set the hours.
6.
Wait until the display switches to the minutes setting.
7.
Press the button to set the minutes.
8.
Wait until the display switches.
The settings are stored.
Radio MINI Boost CD:
1.
Press MENU button.
2.
Press the button.
3.
Press the button.
4.
Select the desired menu item "FORMAT",
"STD" or "MIN" and press the respective button.
5.
Turn the right-hand knob to set values.
6.
Press the right-hand knob to save values.
7.
Press the button to leave settings.
Date
Setting date
Radio MINI CD:
To set the dd/mm or mm/dd date format, see
Formats and units of measure on page 61 .
2.
Keep the button pressed until the display changes.
3.
Press the button repeatedly until the symbol and "SET" appear.
4.
5.
Keep the button pressed until the display changes.
Press the button to set the day.
6.
Wait until the display switches to the month setting.
7.
Set the month and year in the same manner.
8.
Wait until the display switches.
The settings are stored.
Radio MINI Boost CD:
1.
Press MENU button.
2.
Press the button.
3.
Press the button.
4.
Select desired menu item "TT", "MM" or
"JJ".
5.
Turn the right-hand knob to set values.
65
CONTROLS Everything under control
6.
Press the right-hand knob to save values.
7.
Press the button to leave settings.
Check Control
Principle
The Check Control monitors vehicle functions and alerts you to any faults in the systems monitored. Such a Check Control alert involves indicator or warning lights in the displays and, if applicable, an acoustic signal.
> Some Check Control messages are displayed until the faults have been rectified. These messages cannot be hidden. If several faults occur at the same time, the Check Control messages are displayed in succession.
> Other Check Control messages are automatically hidden after approx. 20 seconds, but are not deleted.
Indicator and warning lights can come on in various combinations and colours in panel 1 or 2.
What to do in the event of a fault
See the list starting on page
what each light means in the event of a malfunction and what measures should be taken.
Hiding Check Control messages
Symbol indicates that Check Control messages are stored. Check Control messages can be shown later on.
Displaying memorised Check Control messages
Stored Check Control messages can only be shown when the driver's door is closed.
1.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
Press the button in the flashing turn indicator lever.
66
2.
Keep the button pressed until the display changes.
Everything under control
3.
Press the button repeatedly until the corresponding symbol and "CHECK INFO" appear.
CONTROLS
4.
Hold the button pressed.
"CHECK OK" appears if there are no Check
Control messages.
If a Check Control message has been stored, the corresponding message is displayed.
5.
Press the button to check for other messages.
67
CONTROLS Technical features for driving comfort and safety
Technical features for driving comfort and safety
Park Distance Control
PDC*
Principle
PDC assists you with manoeuvring into a parking space. Acoustic signals warn you of the presence of an object behind the car. Four ultrasonic sensors in the rear bumper perform the measurements.
An acoustic signal sounds once an object is approx. 60 cm, approx. 24 in, from the rear corner sensors, or approx. 1.50 m, approx.
5 ft, from the rear centre sensors. PDC is a parking aid which is capable of registering objects approached at low speed, as is usually the case when the car is being parked. Avoid approaching an object rapidly, otherwise the system may be unable to alert you in sufficient time due to the physical principles involved.
<
If the car is towing a trailer, the rear sensors will be unable to supply meaningful signals. They therefore do not light up.
Automatic mode
With the engine running or the ignition switched on, the system is activated after approx. one second when reverse gear or selector lever position R is engaged. Wait for a brief moment before driving off.
Audible warning signals
The closer the car approaches the object, the more rapid the sequence of signals. When the distance to a detected object is less than approx.
30 cm, approx. 12 in, the signal becomes continuous.
If the distance remains constant, e.g. if you are driving parallel to a wall, the signal is interrupted after approx. 3 seconds.
68
Adjusting
The volume of the signal tones can be adjusted,
see Radio MINI CD, page 108 or Radio MINI
Boost CD, page
.
Malfunction
Indicator light comes on. PDC has failed.
Have the system checked.
As a precautionary measure, keep the sensors clean and free from ice, so that they always operate reliably. When using a highpressure cleaner, do not spray the sensors for extended periods of time and only from a distance of at least 10 cm, approx. 4 in.
System limitations
PDC is no substitute for your personal assessment of obstructions. The sensors have certain dead areas in which objects cannot be detected. In addition, the identification of objects may not be possible if the physical limits of the ultrasonic measuring principle are exceeded, for instance with trailer noses and hitches, and thin or wedge-shaped objects. Low objects already indicated, such as kerbs, may enter the sensors' dead areas before or after a continuous audible signal is given. Higher, protruding objects such as ledges may not be detectable. For this reason, drive prudently, as otherwise there is a risk of personal injury or damage to property. Loud sound sources outside or inside the vehicle can drown out the PDC signal.
<
Technical features for driving comfort and safety
CONTROLS
Driving stability control systems
Your MINI has a number of systems that help to maintain the vehicle's stability even in adverse driving conditions.
Not even driving stability control systems can overcome the laws of physics. It is therefore the driver's responsibility to adopt a suitable driving style in every situation. The added safety this provides should not be undermined by taking risks while driving, otherwise there is a risk of accidents.
<
Anti-lock Brake System ABS
ABS prevents the wheels locking when the brakes are applied. The vehicle can consequently still be steered even when the brakes are applied hard. This increases active driving safety.
ABS is ready to operate each time the engine is started.
Cornering Brake Control CBC
Driving stability and steering characteristics are further enhanced while you are braking in bends or during a lane change.
Electronic Brake Force Distribution EBV
The system regulates the braking pressure on the rear wheels in order to stabilise the braking behaviour.
Brake assist
When the brake is depressed quickly, this system automatically applies maximum braking power assistance. The system thus helps keep braking distance to a minimum. It also makes full use of the advantages offered by ABS.
Maintain pressure on the brake as long as full braking is required.
Dynamic Stability Control DSC
Principle
DSC prevents the driving wheels losing traction when you pull away from rest or accelerate.
DSC also recognises unstable driving conditions, for example if the rear of the car is about to swerve or if momentum is acting at an angle past the front wheels. In such instances, DSC helps to keep the car on a stable course, subject to the limits imposed by the basic laws of dynamics, by reducing the engine output and applying the brakes to individual wheels.
DSC is ready to operate each time the engine is started.
Deactivating DSC
Press button until the DSC OFF indicator light in the revolution counter lights up and DSC OFF is displayed in the revolution counter. DSC is deactivated. Stabilising and the traction-improving effects are no longer available.
When driving with snow chains or if the vehicle has to be rocked out of deep snow, it may be advisable to switch off DSC (dynamic stability control) temporarily.
In the interests of dynamic stability, activate DSC again as soon as possible.
Activating DSC
Press the button again, the indicator lights for
DSC in the display elements go out.
69
CONTROLS Technical features for driving comfort and safety
As a check
Indicator light in revolution counter flashes:
DSC is regulating the propulsive and braking forces.
Indicator light DSC OFF in speedometer lights up and DSC OFF is displayed in revolution counter:
DSC is deactivated.
Activating DTC*
Dynamic Traction Control DTC*
Principle
DTC is a version of DSC that has been tractionoptimised for particular operating conditions, e.g. driving on roads where the snow has not been cleared. The system assures maximum traction, but with reduced dynamic stability. You should therefore drive with caution.
In the following exceptional situations it may be best to activate DTC for a short time:
> When driving on snowed slopes, in slush or on uncleared snowed surfaces.
> When rocking out or driving off from deep snow or loose surface.
> When snow chains are fitted.
Press button until the DSC OFF indicator light in the speedometer lights up and TRACTION is displayed in the revolution counter.
Dynamic Stability Control DSC is deactivated,
Dynamic Traction Control DTC is activated.
As a check
Indicator light in revolution counter flashes:
DTC is regulating the propulsive and braking forces.
The indicator light in speedometer comes on and TRACTION is displayed in the revolution counter:
DTC is activated.
Deactivating DTC*
Press button again, the DSC OFF indicator light in the speedometer and TRACTION in the revolution counter go out.
70
Technical features for driving comfort and safety
CONTROLS
Jointly deactivating DTC* and DSC ALL4 four-wheel drive system*
ALL4 is your MINI's four-wheel drive system. The combined effect of ALL4 and DSC further optimises traction and driving dynamics. The ALL4 four-wheel drive system distributes the torque flow variably to the front and rear wheels in accordance with the driving situation and the condition of the road surface.
Press button for at least 3 seconds, the DSC OFF indicator light in the speedometer lights up and
DSC OFF is displayed in the revolution counter.
Dynamic Traction Control DTC and Dynamic Stability Control DSC are deactivated together. No stabilising intervention will now take place.
Brake intervention, in the form of a differential lock * is used for better drive characteristics, even with deactivated DSC and unevenly spinning drive wheels.
Activating DSC
Press the button again, the indicator lights for in the display elements go out.
Hill Start Assist
The Hill Start Assist enables comfortable driving off on upward inclines. It is not necessary to use the handbrake for this.
1.
Hold the MINI in place by depressing the brake.
2.
Release the brake and drive off immediately without delay.
The Hill Start Assist holds the vehicle in place for approx. 2 seconds after the brake is released.
Depending on the vehicle's load or if towing a trailer, the vehicle might roll backwards a little during this time. After releasing the brake, drive off immediately without delay. After approx. 2 seconds the Hill Start Assist assistant will no longer hold the vehicle in place and the car will start to roll backwards.
<
Sport button*
When you press this button, your MINI reacts in an even sportier manner.
> Engine responds more spontaneously to accelerator pedal movements.
> Steering responds more directly.
> Cooper S engine sounds more sporty in coasting mode.
With automatic transmission:
> Gears are shifted more quickly in the Sport programme.
Activating the system
Press the SPORT button.
The LED lights up.
SPORT is displayed briefly in the revolution counter.
Deactivating the system
> Press the SPORT button again.
> Switch off the engine.
71
CONTROLS Technical features for driving comfort and safety
Run Flat Indicator RPA
Principle
The system does not measure the tyre pressures as such.
The system detects a pressure loss on the basis of a comparison between the speeds at which the individual wheels rotate while the vehicle is in motion.
In the event of a pressure drop, the diameter and therefore the rotational speed of the wheel in question change. This is detected and reported as a flat tyre.
Operating requirements
The system requires initialisation with the correct tyre pressure to ensure a reliable reporting of the flat tyre.
The system must be reinitialised every time tyre pressures are corrected, after each change of a wheel or tyre, and after a trailer has been attached or detached.
System limits
tors.
<
No warning can be given of extreme, sudden tyre failure caused by external fac-
A natural, uniform loss of pressure in all four tyres is not detected. Consequently, check the tyre pressures at regular intervals.
In the following situations, the system could be slow to respond or operate incorrectly:
> If the system has not been initialised
> When driving on snow-covered or slippery surfaces
> Sporty style of driving: causing the driven wheels to spin, high lateral acceleration
> Snow chains are fitted
Initialising the system
On initialisation, the current tyre pressures are stored as a reference for detection of a flat tyre.
Initialisation is started by confirming the correct inflation pressures.
Do not initialise the system while snow chains are fitted.
Using the button in the flashing turn indicator lever
1.
Start the engine, but do not drive off yet.
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
3.
Keep the button pressed until the display changes.
4.
Press button repeatedly until the corresponding symbol and "RESET" appear.
5.
Keep the button pressed until the display changes.
6.
Drive off.
Initialisation is completed while the car is on the move, without any feedback.
Initialising is completed by driving the vehicle; this process can be interrupted at any time. Initialising resumes automatically when you continue your journey.
<
72
Technical features for driving comfort and safety
CONTROLS
Indication of a flat tyre
The warning lights come on in red. In addition a warning signal is heard.
There is a flat tyre or substantial loss of tyre pressure.
1.
Reduce your speed and cautiously stop the car. Avoid violent or sudden braking and steering manoeuvres.
2.
Check whether your vehicle is equipped with normal tyres or with run-flat tyres * .
The symbol identifying run-flat tyres, see page
, is a circle with the letters RSC on the sidewall.
If the car is not fitted with run-flat tyres do not continue driving. Any attempt to drive on can result in a serious accident.
<
Dynamic Stability Control DSC is switched on when a flat tyre is reported.
What to do in the event of a flat tyre
Normal tyres*
1.
Identify the damaged tyres.
To do this, check the inflation pressure in all four tyres.
You can do this using the inflation pressure display in the mobility system, page
.
If all four tyres are inflated to the correct pressures, the Run Flat Indicator might not have been initialised. Initialise the system.
If you cannot tell which wheel is damaged, please contact Service.
2.
Repair the damaged tyre with the mobility
Run-flat tyres*
If a tyre has punctured you can continue your journey, driving at speeds up to a maximum of
80 km/h, approx. 50 mph.
Continuing to drive with a puncture
If you continue a journey with a flat tyre:
1.
Avoid violent or sudden braking and steering manoeuvres.
2.
Do not exceed a speed of 80 km/h, approx.
50 mph, after this.
3.
Check the pressure in all four tyres at the next opportunity.
If all four tyres are inflated to the correct pressures, the Run Flat Indicator might not have been initialised. Initialise the system.
Maximum possible distance with tyres entirely deflated:
The maximum possible distance is determined by load and stress to which the vehicle is exposed during travel.
In the case of average load, the possible distance is approx. 80 km, approx. 50 miles.
The vehicle's handling characteristics change when driving with damaged tyres. Examples include the vehicle swerving more when braking, braking distances increasing and modified self-steering response. Modify your driving style accordingly. Avoid sudden steering movements or driving over obstacles such as kerbs, holes in the road, etc.
As the stress to which the vehicle is exposed is an essential factor in the possible distance that can be travelled with deflated tyres, this distance can be reduced dependent upon speed, road conditions, outside temperature, stress, etc. Conversely, it can be increased by adopting a more conservative driving style.
Drive with caution and do not exceed a speed of 80 km/h, approx. 50 mph.
In the event of a loss of tyre inflation pressure driving characteristics change, e.g. reduced track stability during braking, longer braking distance and different self-steering properties.
<
When towing a trailer, heavy trailers in particular may start to snake. Therefore do not exceed a speed of 60 km/h, approx.
35 mph, otherwise there is a risk of accident.
<
Vibration or loud noises while driving may be an indication that the tyre has finally failed. Reduce speed and stop, otherwise parts
73
CONTROLS Technical features for driving comfort and safety of the tyre could come loose and cause an accident. Do not drive the car any further and contact Service.
<
Dynamic brake lights*
On the right: hard braking.
When you apply the brakes hard, the brake lights of your MINI flash. If the vehicle has been braked in this way, the hazard warning flashers are activated and the brake lights remain lit without flashing.
The hazard warning flashers are only deactivated when you accelerate again, or can be cancelled manually.
On the left: normal braking.
Airbags
There are the following airbags beneath the covers indicated:
1 Front airbags
2 Side airbags in the backrest
Protective effect
risk.
<
Failure to comply with the notes on page
32 may put your personal safety at
The front airbags protect the driver and front passenger in the event of a head-on collision, if the protective action of the seat belts alone would be insufficient. The head-level and side airbags provide protection in the event of a side-
3 Head airbags in the front and rear passenger compartment on collision. The side airbag has the effect of supporting the upper body from the side. The head-level airbag supports the head of the seat's occupant.
The airbags will purposely not be activated by every collision, e.g. not by more minor accidents, certain rollover situations and rear-end collisions.
74
Technical features for driving comfort and safety
CONTROLS
Never attach any material to the airbag covers with adhesive, place material over them or modify them in any other way.
Keep the instrument panel and windscreen on the driver's side clear, i.e. do not affix adhesive films or coverings, nor mount holders e.g. for a navigation device or mobile phone, in that area.
Do not fit any protective covers, seat cushions or other objects to the front seats unless they have specifically been approved for use on seats with integral side airbags. Do not hang items of clothing such as coats or jackets over the backrests.
Do not dismantle the airbag occupant restraint system. Do not modify the individual components of the system or its wiring in any way. This includes the upholstered covers on the steering wheel, instrument panel, seats and roof posts as well as the sides of the roof lining. Do not remove the steering wheel.
<
Avoid touching the system's components immediately after it has been triggered off, as there is a risk of sustaining burns.
Only have testing, repairing or removing or scrapping of airbag generators performed by your Service or a workshop that has the required licences under explosives regulations.
Any careless or unskilled interference with the system could otherwise lead to its failure or to accidental triggering with the risk of injury.
<
Operational status of airbag system
Airbag system faulty
> Warning light does not light up from radio readiness.
> Warning light remains permanently on.
In the event of a fault in the airbag system, have it checked without delay, as there is otherwise the risk that the system will not function as intended even if a sufficiently severe accident occurs.
<
As of radio readiness, page
comes on briefly, indicating the operational readiness of the entire airbag system and the belt tensioners.
75
CONTROLS Lights
Lights
Side lights/low-beam headlights
0 Lights off
1 Side lights
2 Low-beam headlights and welcome lights
3 Automatic driving lights control * , daytime driving lights * , welcome lights and Adaptive
Head Light *
If you open the driver's door with the ignition switched off, the exterior lighting is switched off automatically if the light switch is in position 0, 2 or 3.
If required, switch on the side lights, switch position 1.
Side lights
Turn switch to position 1.
The lights come on all round the car.
For the additional option of parking lights on one side of the vehicle only, page
The side lights will discharge the battery.
Do not leave them switched on for too long, otherwise the engine may fail to start.
<
Low-beam headlights
Turn switch to position 2.
The low-beam headlights come on when the ignition is on.
Automatic driving lights control*
When the switch is in position 3, the low-beam headlights are switched on and off automatically depending on ambient light conditions, e.g. in a tunnel, in twilight and precipitation. Adaptive
Head Light * is active.
The headlights may also switch on when the sun is sitting low on a blue sky.
When driving into brightly illuminated tunnels, there may be a delay before the headlights come on.
Irrespective of the ambient light level, the lowbeam headlights remain on if you switch on the fog lights * .
When the daytime driving lights are activated, page
, the low-beam headlights always come on in switch position 3 when the ignition is switched on. The car's exterior lights are automatically switched off after the car is parked.
The driving lights control function is no substitute for your individual judgement of when it is necessary to switch on the lights.
The sensors are unable, for instance, to recognise fog or hazy weather. In such situations, switch on the lights manually to avoid any safety risk.
<
Welcome lights
If you leave the light switch in the position for low-beam headlights or automatic driving lights control when you park the vehicle, the side lights and interior light come on for a certain time when you unlock your car.
Headlight courtesy delay feature
If you activate the headlight flasher after the ignition has been switched off, the low-beam headlights will remain on for a certain time.
The setting is stored for the remote control in
use, see Personal Profile, page 20
.
76
Lights
CONTROLS
Adjusting the duration or deactivating the function
1.
Switch on the ignition, see page
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
3.
Keep the button pressed until the display changes.
4.
Press the button repeatedly until the symbol and "SET" appear.
8.
Press button to select:
>
The function is deactivated.
> …
Select the corresponding duration, e.g.
40 seconds.
9.
Press the button for longer.
The setting is stored.
Daytime driving lights*
The daytime driving lights come on when the light switch is in position 3 and the ignition is switched on.
The car's exterior lights are automatically switched off after the car is parked.
Switch on the side lights separately, if necessary.
Activating/deactivating daytime driving lights
The setting is stored for the remote control in
use, see Personal Profile, page 20
.
1.
Switch on the ignition, see page
2.
Press the button in the turn indicator lever repeatedly until "SET/INFO" appears.
5.
Keep the button pressed until the display changes.
6.
Press the button repeatedly until the indicated symbol appears.
3.
Keep the button pressed until the display changes.
7.
Keep the button pressed until the display changes.
77
CONTROLS Lights
4.
Press the button repeatedly until the symbol and "SET" appear.
5.
Keep the button pressed until the display changes.
6.
Press the button repeatedly until the indicated symbol, arrow, appears.
the road ahead on the basis of steering angle and other parameters.
Variable light distribution * illuminates the road surface even more effectively in accordance with the vehicle's speed.
The light distribution is automatically adapted to the speed. The town light is active at a speed less than 45 km/h, approx. 30 mph. The motorway light is switched on at a speed higher than
110 km/h, approx. 68 mph after approx.
30 seconds or above of a speed 140 km/h, approx. 87 mph.
Activating Adaptive Head Light
With the ignition switched on, turn the light
switch to position 3, see page 76
.
Standstill function * : to avoid dazzling drivers of oncoming vehicles, Adaptive Head Light points towards the front passenger's side when the vehicle is stationary.
Malfunction
A message is displayed.
The Adaptive Head Light is faulty or has failed.
Have the system checked as soon as possible.
7.
Keep the button pressed until the display changes.
8.
Press button to select:
>
Daytime driving lights activated.
>
Daytime driving lights deactivated.
9.
Press the button for longer.
The setting is stored.
Headlight beam throw adjustment
Halogen lights
Adaptive Head Light*
Principle
Adaptive Head Light is a variable headlight control system that makes it possible to illuminate the road surface more effectively. The light cones from the headlights are directed to suit
The beam throw of the low-beam headlights must be adjusted manually to suit the load car-
78
Lights
CONTROLS ried in the car, otherwise the drivers of oncoming vehicles could be dazzled.
The second value in each case applies when towing a trailer.
0 / 1 = 1 to 2 persons without luggage
1 / 1 = 4/5 persons without luggage
1 / 2 = 4/5 persons with luggage
2 / 2 = 1 person, luggage area full
Comply with rear axle load limit, page 187 .
Xenon headlights*
Beam throw is regulated automatically, e.g. when you accelerate or brake, as well as for different loads.
The parking lights will drain the battery.
Do not leave them switched on for too long, otherwise the engine may fail to start.
<
Switching off
Press the lever upwards or downwards to the pressure point.
Fog lights*
High-beam headlights/ parking lights
1 Flashing turn indicators/parking lights *
2 Switching on the high-beam headlights
3 Switching off the high-beam headlights/ headlight flasher
Right or left parking lights*
The vehicle can be lit on one side for parking purposes. Observe all country-specific regulations.
Switching on
After parking the car, hold the lever up or down, arrow 1.
1 Fog lights *
2 Rear fog light *
To switch on or off, press the respective switch.
Fog lights*
The side lights or low-beam headlights must be switched on. The green indicator light comes on while the fog lights are switched on.
If automatic driving lights control has been activated, the low-beam headlights come on automatically when the front fog lights are switched on.
<
Front fog lights*
In the switch position 3 the low-beam headlights are adjusted to lighting conditions in conjunction with the variable light distribution * when the fog lamps are switched on.
The leading foglight provides wider illumination up to a speed of 110 km/h, approx. 68 mph.
Rear fog light*
Low-beam headlights or parking lights with fog lights must be switched on. The yellow indicator
79
CONTROLS Lights light comes on while the rear fog light is switched on.
Instrument lighting
You can adjust the brightness of the instrument lighting only when the side lights or the lowbeam headlights are switched on.
Switching the interior light on/off manually
Interior light on/off.
Press the switch.
To switch off the light permanently, press the switch for about 3 seconds.
Reading lights*
There are reading lights at the front next to the interior lights and in the rear*.
Increasing brightness
Keep the button pressed until the desired brightness is achieved.
Decreasing brightness
Press button briefly.
Brightness is reduced each time the button is pressed.
Interior light
The interior light, the footwell lights * , the kerb lights * and the luggage area light are controlled automatically.
To preserve the battery, all lights inside the car are switched off a short time after
the ignition is switched off, see Start/stop button
on page
<
Reading lights on/off.
Front: press the switch.
Rear: press the button.
80
Ambient lighting*
The colour and brightness of the ambient lighting can be changed.
> Press the switch forwards.
Colour changes in increments.
> Press the switch backwards.
Brightness changes in increments.
Intermediate settings or colours are possible.
To change the colour of the ambient lighting permanently, press the switch forwards and hold it there for more than
10 seconds.
<
Lights
CONTROLS
81
CONTROLS
Climate
Climate
Equipment versions
Depending on the equipment version, your MINI will have air conditioning or automatic air conditioning * .
2 Automatic air-conditioning system *
Air outlets
3 Air to windscreen and side windows
4 Air to the upper body area, draught-free ventilation
5 Air to footwells
82
Climate
CONTROLS
Air conditioner
1 Air volume
2 Cooling function
3 Recirculated-air mode
4 Temperature
5 Rear window heating
6 Air distribution
7 Windscreen heating *
Air flow rate
Adjust the air flow. The higher the rate, the more effective the heating or cooling will be.
The air volume may be reduced or the system may even shut down entirely, to preserve the battery.
Switching the system on/off
Turn the air flow rotary switch to 0. Blower and air conditioner are completely switched off and the air supply is cut off.
To switch on the air conditioner, set any desired air flow.
Cooling function
When the cooling function is on, air is cooled and dried, then reheated according to the temperature setting. The function is only available with the engine running.
The air conditioning function helps avoid or quickly remove condensation.
Depending on weather conditions, the windscreen may fog over momentarily when the engine is started.
Switch on recirculated-air mode to speed up and intensify air cooling at high temperatures.
<
Recirculated-air mode
If the air outside the car has an unpleasant odour or contains pollutants, shut off the supply to the interior of the car temporarily. The air inside the vehicle is then recirculated.
If the windows mist over in recirculatedair mode, switch off recirculated-air mode and increase the air volume if necessary.
Recirculated-air mode should not be used continuously for lengthy periods, as the quality of the air inside the vehicle will otherwise deteriorate gradually.
<
Temperature
Turn upwards towards red to increase the temperature.
Turn downwards towards blue to decrease the temperature.
Rear window heating
The rear window heater switches off automatically after a certain time.
83
CONTROLS Climate
The rear window heating may be reduced or the system may even shut down entirely, to preserve the battery.
Air distribution
Direct the flow of air to the windows , to the upper body area or to the footwell .
Intermediate settings are possible.
Windscreen heating*
The windscreen heating is switched off automatically after a certain time.
The windscreen heating may be reduced or the system may even shut down entirely, to preserve the battery.
Defrosting windows
1.
Set the maximum air flow rate.
2.
Air distribution in position .
Switching on the cooling function * helps clear the mist from the windows more rapidly.
3.
Set the highest temperature, red.
4.
Deactivate recirculated-air mode.
5.
If necessary, switch on the windscreen heating.
6.
If necessary, switch on the rear window heating.
Microfilter
The micro-filter traps dust and pollen. The micro-filter is changed by your MINI Service Centre during routine maintenance work.
Automatic air-conditioning system*
1 Adjusting air volume manually
2 AUTO program
3 Recirculated-air mode
4 Maximum cooling effect
5 Manual air distribution
6 Temperature
7 Defrosting windows and removing mist
8 Cooling function
9 Rear window heating
10 Windscreen heating *
Preferred interior climate
The AUTO programme 2 offers optimal air distribution and air flow rate for almost all conditions,
see AUTO program below. All you need to do is
select an inside temperature you find comfortable.
The following sections inform you in detail about how to adjust the settings.
Most settings are stored for the remote control
in use, see also Personal Profile settings on
page
.
84
Climate
CONTROLS
Adjusting air volume manually
Press the – button to reduce the air flow rate. Press the + button to increase it.
You can switch the automatic function for the air volume back on by pressing the
AUTO button.
The air volume may be reduced or the system may even shut down entirely, to preserve the battery. The display remains unchanged.
Switching the system on/off
Decrease air flow by pressing the – button until the system is switched off. All indicators go out.
Press the AUTO button to switch the automatic air-conditioning system back on.
AUTO program
The AUTO program adjusts the air distribution to the windscreen and side windows, towards the upper body area and into the footwell for you. The air flow rate and your temperature specifications will be adapted to outside influences as a result of seasonal changes, e.g. sunlight.
The cooling function is switched on automatically in the AUTO program.
Recirculated-air mode
recirculated.
Recirculated-air mode: the ambient air supply is permanently shut off. The air inside the vehicle is then
If the windows mist over in the recirculated-air mode, press the AUTO button or switch off the recirculated-air mode and increase the air volume if necessary.
Recirculated-air mode should not be used continuously for lengthy periods, as the quality of the air inside the vehicle will otherwise deteriorate gradually.
<
Maximum cooling effect
At outside temperatures above
0 6/327 and when the engine is running, you obtain a maximum cooling effect as soon as possible.
The automatic air conditioning enters the recirculated-air mode at the lowest temperature possible. Air flows at maximum rate from the outlets for the upper body area. You should therefore open these outlets for maximum cooling.
Adjusting air distribution manually
Depending on the selection, the flow of air is directed to the windows, to the upper body area or to the footwell.
You can switch the automatic air distribution back on by pressing the AUTO button.
Temperature
Set the desired temperature individually.
The automatic air conditioning attains this temperature as quickly as possible regardless of the season by using maximum cooling or heating power if necessary. The temperature is then maintained.
The automatic air conditioning does not have sufficient time to establish the set temperature when temperature settings are changed quickly in succession.
<
Rear window heating
The rear window heater switches off automatically after a certain time. Depending on the equipment specification, the top wires serve as the antenna and are not part of the rear window heating.
Defrosting windows
Remove ice and condensation quickly from the windscreen and from the front side windows.
Also switch on the cooling function.
The windscreen heating * is switched on automatically.
85
CONTROLS Climate
Windscreen heating*
The windscreen heating is switched off automatically after a certain time.
Ventilation
Cooling function
The passenger compartment can only be cooled if the engine is running.
Air is cooled and dried when the cooling function is switched on, then reheated to suit the temperature setting.
The cooling function helps to avoid mist forming on the windows or to remove it rapidly.
Depending on weather conditions, the windscreen may fog over momentarily when the engine is started. If necessary, the recirculatedair mode is switched on automatically.
The cooling function is activated automatically when the AUTO button is pressed.
Micro-filter/activated charcoal filter
The micro-filter traps dust and pollen. The activated charcoal filter in addition removes gaseous pollutants from the air entering the vehicle.
This combined filter is changed by your MINI
Service Centre during routine maintenance work.
You can call up further information in the Next
Service indicator, page
1 Knob to open and close continuously
2 Nozzle for direction of air flow
Opening/closing
Turn the knob.
Directing the air flow
Swivel the entire nozzle.
86
Practical interior equipment
CONTROLS
Practical interior equipment
Glove compartment
Opening
Closing
Turn the switch in the opposite direction of the arrow into a vertical position.
Depending on the temperature setting for the air conditioner or automatic air-conditioning system, high temperatures could result in the glove compartment.
To open the cover, take hold of the handle.
The light in the glove compartment comes on.
Closing
Swing lid up.
After using the glove compartment while the car is moving, close its lid so that it cannot cause injury in the event of an accident.
<
Ventilation*
Depending on the vehicle's equipment version, the glove compartment can be ventilated; When the cooling function is on * , it can be cooled.
Connection for external audio device
You can connect an item of external audio equipment, e.g. a CD or MP3 player, and play back music via the vehicle's loudspeakers: see section Entertainment, page
or
.
Centre armrest*
Storage compartment
Depending on the version, the centre armrest between the front seats contains either a compartment or a cover for the mobile phone bracket * or the snap-in adapter * .
Opening
Press the button, arrow, and pull the cover up.
Opening
Turn switch in the direction of the arrow.
87
CONTROLS Practical interior equipment
Storage compartments
In the passenger compartment
Depending on your vehicle's equipment version, storage compartments can be found in the front and rear doors as well as in the centre console * .
Pockets * are located in the backrest rear panels of the front seats.
Centre rail
Various accessories can be attached to a special base plate on the centre rail and positioned at various points. These include cup holders * and mobile phone holders * .
Do not mount accessories in vicinity of hand brake as otherwise this may be damaged when the hand brake is actuated.
<
An example: cup holders
Fitting the base plate
The lever 3 can be locked in three positions.
0 Fixing
1 Sliding in the rail
88
2 Fitting the base plate
For fitting move the lever to position 2.
Moving and securing
1.
Press lever 3 into position 1.
2.
Slide base plate.
3.
Press lever 3 down, into position 0 and fix base plate.
Before driving off, secure the base plate to prevent the risk of injury in the event of an accident.
<
Adding cup holders
1.
Fix base plate if required, see Moving and securing.
2.
Pull lever 6 upwards to unlock mounting.
3.
Start by locking cup holders into the front mountings 4 and then lock them in the rear mountings 5.
Make sure that the lever 6 is opposite the mounting 4.
<
Coat hooks
There are coat hooks on the grab handles in the rear seating area.
Items of clothing hung from the hooks must not obstruct the driver's view. Do not hang heavy objects from the hooks, as they could endanger the vehicle's occupants, e.g. in case of heavy braking or sudden swerving.
<
In the luggage compartment
Depending on your vehicle's equipment version, there are the following storage options:
Practical interior equipment
CONTROLS
> Storage compartment under the level load platform *
> Multi-function hook on the facing for the roller cover for luggage compartment
When leaving the car, always remove the key so that children cannot operate the cigarette lighter and burn themselves.
<
Drinks holders and ashtray*
Connecting electrical appliances
You can use electrical devices such as a hand lamp, car vacuum cleaner, etc., up to approx.
140 watts at 12 volts if at least one of the following sockets is provided. Do not damage the sockets by attempting to insert plugs of the wrong pattern.
Cigarette lighter socket
Pull the cigarette lighter * or cover out of the socket.
Power sockets*
In the rear
Drinks holder*
Use lightweight break-proof containers and do not carry hot drinks. Otherwise there is an increased risk of injury in the event of an accident.
<
Do not force unsuitable containers into the drinks holders. Otherwise, damage may result.
<
Other drink holders can be mounted in the rear on the centre rail.
Ashtray*
The ashtray is located in one of the drinks holders at the front in the centre console.
Emptying
Take out the entire ashtray.
Lighter
With the engine running or the ignition switched on, press in the cigarette lighter.
The cigarette lighter can be removed when it pops back out.
Hold the hot cigarette lighter only by its knob, otherwise you may suffer burns.
Pull out the cover.
In the luggage compartment
Pull out the cover.
89
Drive Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
DRIVING HINTS Driving precautions
Driving precautions
Running in
Moving parts need a certain time to achieve maximum operating efficiency as a unit. Comply with the following instructions, which are intended to ensure that your car achieves its optimum operating life and economy.
Engine and final drive
Observe the speed limits in the country where you are driving.
Up to 2000 km, approx. 1200 miles
Drive at varying road and engine speeds, but do not exceed the following values:
> Petrol engine
4500 rpm, or 160 km/h, approx. 100 mph
> Diesel engine
3500 rpm, or 150 km/h, approx. 90 mph
Avoid full throttle and do not use the automatic transmission kick-down.
From 2000 km, approx. 1200 miles, onwards
Engine and road speeds can be gradually increased.
Tyres
New tyres do not achieve their full road grip immediately, for production reasons. You should therefore drive in a restrained manner for the first 300 km, approx. 200 miles.
Brake system
Brake pads and discs do not achieve a favourable wear and contact pattern until the car has covered about 500 km, approx. 300 miles. Drive with caution during this running in period.
Clutch
The clutch needs to be run in for about 500 km, approx. 300 miles, before it will operate with maximum efficiency. Operate the clutch gently while running it in.
After fitting new parts
The same running in procedures should be observed if any of the components mentioned above have to be renewed in the course of the car's operating life.
General driving notes
Closing the tailgate
Drive only with the tailgate closed. If the tailgate is not closed, in the event of an accident or during braking or when taking evasive action, the safety of passengers and other road users could be put at risk and the vehicle may sustain damage. Furthermore, exhaust gases could enter the passenger compartment.
<
If it is nevertheless necessary to travel with the tailgate open, observe the following precautions:
1.
Close all windows and the glass roof * .
2.
Switch off recirculated-air mode and significantly increase the air flow rate of the air conditioning or automatic air conditioning,
.
Hot exhaust system
High temperatures occur in the exhaust system of all vehicles. Never remove the heat shields protecting the exhaust system, nor apply underseal to them. Make sure that when the vehicle is driven or parked and when the engine is idling, no easily flammable material such as hay, leaves, grass, etc. comes into con-
92
Driving precautions
DRIVING HINTS tact with the hot exhaust pipe. It could ignite and cause a fire, with the risk of severe injuries or damage. Do not touch hot exhaust tail pipes; otherwise there is a risk of burns.
<
Diesel particle filter*
The diesel particle filter collects soot particles and burns them periodically at high temperatures. This cleaning procedure takes several minutes. During that time, the engine may sound slightly different and require slightly higher engine speeds for normal power development. In that case, the engine fan can be switched on even at low ambient temperatures.
In addition, the exhaust may emit a small amount of smoke, even after the engine has been switched off.
For Australia/New Zealand: radio signals
The vehicle's performance may be affected by interference from high frequency radio signals. Such signals are emitted by certain transmitting devices, for example, aircraft navigation beacons or mobile phone relay stations.
Should you encounter problems of this nature, we recommend seeking advice from your MINI
Service Centre.
<
For Australia/New Zealand: towing
The Australian/New Zealand Standards
AS 4177.1 - 2004 Caravan and light trailer towing components - Towbars and towing brackets includes the following statement which the manufacturer of your MINI herewith adopts:
"FOR TRAILER TOWING ONLY". The towbar supplied with your MINI vehicle should only be used for towing purposes, the towbar assembly should not be used in conjunction with any towbar-mounted carrying device, such as, for example, a bicycle carrying rack.
As all MINI towbar assemblies are designed, tested and approved as a single unit, the practice of modifying or replacing the MINI supplied towball mount assembly is not approved. Use only the genuine MINI towball mount assembly.
The manufacturer of your MINI does not recommend or support the installation and use of a
Weight Distribution Hitch or Load Levelling
Device on any MINI vehicle. The use of such devices may affect the vehicle's warranty status.
We recommend you consult your Authorised
MINI Dealer for any further advice or clarification.
Aquaplaning
When driving on wet or slushy surfaces, reduce speed to prevent a wedge of water from forming between the tyre and the road.
This situation, known as aquaplaning, means that the tyre can actually lose contact completely with the road surface, so that neither the car can be steered nor the brake be properly applied.
<
The risk of aquaplaning increases with declining
tread depth on the tyres, see also Tread depth on page 142 .
Driving through water
Drive through water only to a max. depth of 30 cm, approx. 1 ft, and no faster than walking pace, otherwise the engine, electrical system and transmission may be damaged.
<
Handbrake on uphill gradients
Never try to prevent the car from rolling back on an uphill gradient by slipping the clutch; always apply the handbrake. The clutch will otherwise wear rapidly.
<
Support by Hill Start Assist, see page 71
.
Safe braking
Your MINI is equipped with ABS. Applying the brakes fully is the most effective way of braking in situations in which this is necessary. Since the vehicle remains steerable, you can avoid obstacles by turning the steering wheel as smoothly as possible.
93
DRIVING HINTS Driving precautions
The pulsating sensation at the brake pedal, combined with the sound of the hydraulic system operating, indicates that ABS is intervening.
Objects in the movement range of the pedals
Make sure that pedal functions are not impaired during travel by floor mats, carpets or other objects. Do not place additional floor mats on top of existing floor mats or other objects. Only use floor mats which have been approved for use with the vehicle and can be securely fastened in place. If you remove floor mats, for cleaning for example, make sure that you fasten them securely back in place.
<
Wet roads
In wet conditions or heavy rain, apply the brakes briefly with slight pedal pressure every few kilometres or miles. When doing so, make sure that no other road user is endangered. The resulting heat dries the brake discs and pads. The full braking force will then be available immediately if needed.
Downhill gradients
To avoid impairing the efficiency of the brake system as a result of overheating, drive down long or steep descents in the gear that allows you to keep brake applications to a minimum. Otherwise even slight continuous pressure on the brake could cause overheating, brake pad wear or even brake system failure.
<
You can increase the engine's braking effect by shifting down through the gears all the way to first gear, if necessary. This avoids overburdening the brakes. Downshifting in manual mode of
the automatic transmission, page 51 .
Never drive with the clutch held down, with the transmission in neutral or with the engine switched off; engine breaking action will not be present, or there will be no power assistance to the brakes or steering.
Make sure that pedal functions are not impaired by floor mats, carpets or other objects.
<
Corrosion of brake discs
If the vehicle is used only for short distances, is not used for lengthy periods or is subjected to only minor loads, the brake discs will be particularly susceptible to corrosion and the brake pads will collect dirt; this is because the necessary brake pressure for a self-cleaning effect has not been generated.
When the brakes are applied, corroded discs tend to judder, and even lengthy brake applications usually fail to eliminate this effect entirely.
When vehicle is parked
Moisture condensate forms in the automatic air conditioning and is discharged underneath the vehicle. Traces of water on the ground are therefore normal.
After stopping the engine, the coolant pump in the MINI Cooper S can continue running for a certain time. This leads to noises in the engine compartment.
Rule of the road
When entering countries where the traffic drives on the opposite side of the road to the country in which your car is registered, certain measures are necessary to avoid dazzling the drivers of oncoming vehicles.
Halogen headlights
Masking film is available from your MINI Service
Centre. Apply it according to the instructions enclosed with the film.
Xenon headlights
The light distribution of the xenon headlights has been designed so that additional measures do not need to be taken to avoid dazzling the drivers of oncoming vehicles.
Low-beam headlights, switch position 2, turn on.
94
Driving precautions
DRIVING HINTS
Load
Avoid overloading the vehicle, as this could cause the tyres' load capacity limit to be exceeded. The tyres could then overheat and sustain internal damage. This could lead to sudden pressure loss.
<
Make sure that no fluids are leaking in the luggage compartment. Otherwise the vehicle could be damaged.
<
Expanding the luggage compartment
Luggage compartment cover
Do not place any items on the cover, as they may be dislodged by braking or avoidance manoeuvres and endanger the occupants or damage the cover.
<
In the MINI, the luggage area cover is raised when the tailgate is opened.
The cover can be removed to facilitate transporting bulky items.
1.
Unhook retaining straps from the tailgate.
2.
Lift the cover slightly, arrow 1, and pull it towards the rear out of the holder, arrow 2.
Comply with the notes on seat belts on
, or there may be a risk to your personal safety.
<
5-seater: the rear seat backrest is divided 40-20-
40.
When the outer rear seat backrests are folded down, you must not carry any passengers on the seat in the centre.
<
Remove the third head restraint if necessary, see
Removing head restraints on page 34
.
Undo the centre seat belt and insert it into the mounting in the roof lining, see page
Enlarge the luggage area by setting the rear seat backs at a steeper angle.
There are 10 possible settings for adjusting and folding down the backrests between comfort position and transport position.
In the comfort position, the backrests are set as far back as they will go. In the transport position they are more or less vertical.
Before fitting a child restraint system, please read and follow the instructions starting on
.
Rear seat backrests
Before folding back the backrests, make sure that the movement range of the backrests is free. Especially when the middle section is folded over, make sure that no-one is in or reaches into the movement range. As otherwise injuries or damage can be caused.
<
1.
Hold backrest in the upper range, e.g. on the headrest and pull the loop, arrow.
2.
Lock the backrest in or fold it down to the required position.
Folding up backrests
When folding back, make sure that the lock has properly snapped into place. Otherwise loads in the vehicle interior can shift during braking and avoidance manoeuvres and occupants can be endangered.
<
95
DRIVING HINTS Driving precautions
Do not use any child restraint systems in the rear when the rear seat backs have been raised to a steeper angle; otherwise their protective effect may be impaired.
<
The backrests lock in the transport position when folded up from the folded-down position.
Hold the backrest to set the required backrest angle or backrest comfort position, pull the loop forwards and set the backrest.
Luggage compartment cargo cover*
There is a cargo cover between the luggage compartment and the rear seat backrest. This can be folded down and used as the loading floor.
When the backrests are folded over, do not make the sight protection upright. In the case of an accident, the load could fold over the sight protection and damage it.
<
Folding down the cargo cover
1.
Remove the roller cover for luggage com-
partment if necessary, page 95
.
2.
Fold up the cargo cover at the rear, arrow 1.
Folding the cargo cover forward
1.
Fold down the rear seat backrests.
2.
Unlock the cargo cover, see above.
3.
Take hold of the cargo cover on either side and pull it forward over the folded-down rear seat backrests.
Removal
1.
Remove the roller cover for luggage com-
.
2.
Fold the cargo cover up and unlock it, see
Folding the cargo cover forward.
3.
Pull the cargo cover out of the guides on the luggage compartment floor, arrows, and remove it.
Level load platform*
To avoid the risk of damage, do not exceed the maximum load of 150 kg, approx. 330 lb, for the flat luggage compartment floor.
<
Access to the storage space
A storage space, e.g. for stowing the luggage compartment partition net * , is located underneath the flat luggage compartment floor.
3.
Undo the locks on the left and right-hand sides, arrows 2.
4.
Take hold of the cargo cover on either side and pull it down.
To avoid the risk of damage, do not exceed the maximum load of 150 kg, approx. 330 lb, when the cargo cover is folded down in the flat luggage compartment floor position.
<
96
Driving precautions
DRIVING HINTS
1.
Reach into the recess, arrow 1, on the rear edge of the luggage compartment floor.
Installation behind the front seats
2.
Lift luggage compartment floor at rear and fold forwards, arrow 2.
Before closing the tailgate, unhook the loops and fold the luggage compartment floor back down into the flat position.
Removal
The luggage compartment floor can be removed if required. To do this raise luggage compartment floor at recess, fold it together and take it out.
Partition net*
Make sure that the partition net is firmly secured, as otherwise injuries could result.
<
Before installing
1.
Take the bag containing the partition net out of the storage compartment underneath the luggage compartment floor.
2.
Take the partition net out of the bag and unroll and unfold the net.
When you have finished using it, fold and roll the partition net back up and put it back in the bag so that it can be stowed underneath the floor panel again. Keep hooks and tensioning clasps away from bar elements.
3.
Fold out the partition net until the bar elements engage.
1.
Remove the roller cover for luggage compartment if necessary.
2.
Folding down the rear seat backs, see
Expanding the luggage compartment.
3.
Push each of the securing pins of the partition net as far as they will go into the front mountings in the headlining, arrow 1, and push forwards.
4.
Attach the hooks, arrow 2 underneath the straps to the eyes in both sides of the vehicle floor.
5.
Secure the partition net by tightening the straps on the tensioning clasps.
Removing
To remove and stow the partition net, proceed in reverse order.
To roll the net up, press the release button, arrow.
97
DRIVING HINTS
Multi-function hooks*
Driving precautions
Securing the load
Holders on the left and right-hand sides of the facing for the roller cover for luggage compartment, arrow, to which shopping backs or carrier bags can be attached, for example.
Do not use the hooks to carry heavy bags or bulky objects. Otherwise, flying objects could pose a danger when braking and swerving.
Heavy luggage should always be secured and carried in the luggage compartment.
<
Loading
> Position heavy objects as low and as far forward as possible, ideally directly behind the seat backs.
> Wrap protective material round sharp corners and edges.
> When carrying very heavy loads with no passengers on the back seat, insert both seat belts into the respective opposite buckles.
> Do not stack items higher than the top edge of the seat backs.
> Using the partition net, see page
sure that objects cannot poke through the partition net.
> Smaller, lighter objects can be secured with retaining straps or tensioning straps * .
> Your MINI Service Centre can supply suitable lashings * for securing larger or heavier loads.
> There are eight * securing eyes to which these lashings can be attached.
Two of these are located on each of the side panels of the luggage compartment * , arrows 1.
There are another two on either side of the rear panel of the luggage compartment, arrow 2.
To use the bottom lashing eyes, fold up or remove the luggage compartment floor.
Please note the information supplied with load securing equipment.
Always stow and secure the load as described above, so that it cannot endanger the car's occupants, for example if sudden braking or swerving is necessary.
Do not exceed the car's permitted gross weight or the axle load limits, page
, otherwise the car is no longer safe to operate and the construction and use regulations are violated.
Heavy or hard objects should not be carried loose inside the car, since they could be dislodged, e.g. by braking or swerving manoeuvres, and endanger the occupants. Do not secure any load with the top attachment points for ISOFIX, page
them.
<
98
Driving precautions
DRIVING HINTS
Roof rack*
A special roof rack system is available as an accessory for your MINI. Your MINI Service Centre will gladly provide details. Follow the installation instructions for the roof rack system.
Loading the roof rack
A loaded roof rack alters the car's road behaviour and steering response quite considerably, by shifting its centre of gravity.
When loading the roof rack, ensure that the specified roof load limit, the vehicle's gross weight limit and the axle loads are not exceeded.
The relevant figures are shown in the Weights section on page
.
The roof load must be distributed uniformly and should not be too large in area. Heavy items should always be placed at the bottom.
When loading, see that there is sufficient free space for free movement for the glass sunroof.
Correct, secure loading of the roof rack will prevent items from shifting or falling off during the journey.
Drive smoothly. Avoid violent acceleration, braking or cornering.
Rear luggage rack*
A special rear luggage rack is available as an optional accessory. It does not require a tow hitch.
Follow the assembly instructions.
Mounting points
The mounting points are located underneath the sealing caps on the bumper.
Removing the sealing caps, see page
Loading rear luggage rack
Do not exceed the permissible total weight and axle weights when loading.
The relevant figures are shown in the Weights
Towing a trailer
Vehicles built with a factory-installed trailer tow hitch come with the standard equipment of reinforced springs at the rear axle and, depending on the vehicle model, with a more powerful engine cooling system.
The trailer load limit is given on page 190 .
Trailer tow hitch with detachable ball head*
General
The detachable ball end is stowed in a bag under the flat floor in the luggage compartment.
99
DRIVING HINTS Driving precautions
The mounting of the removable ball head and the trailer socket are located on the floor behind the bumper.
A fitted ball head covers the number plate. For this reason, remove the ball head before driving without a trailer.
Ball head
The ball head can be inserted when the following points have been fulfilled:
> The red marking on the handwheel 6 points to the white area on the ball head.
> The handwheel 6 stands clearly apart from the shaft of the ball head.
> The locking ball 3 can be completely pressed into the shaft.
> The key points to the symbol 'Lock open' and cannot be pulled out.
If the ball head has not been pretensioned, carry out the following steps:
1.
Remove cover from lock, if required insert key.
2.
Turn key clockwise.
3.
Pull out handwheel in direction of arrow 1 and hold firmly.
1 Protective cap
2 Ball head
3 Shaft
4 Locking ball
5 Release ball
6 Cover
7 Handwheel
8 Key
Attaching the ball head
Before attaching the ball head
The lock in the handwheel 7 must be unlocked before attachment. The key 8 is clamped in the unlocked lock.
Before attachment the lock must be prepared:
4.
Turn handwheel until it snaps into place in direction of arrow 2. Red marking on handwheel must point to white marking on ball head.
There is a gap between the ball head and the handwheel.
It must be possible to completely press the locking balls into the ball head. Do not touch the handwheel after pretensioning.
Inserting the ball head
When inserting the ball head do not keep your hand in the area of the handwheel, as otherwise this can get trapped and there is a risk of injuries.
<
100
Driving precautions
DRIVING HINTS
1.
Remove the cover stopper of the mounting by pulling it downwards and stow it in the vehicle.
2.
Insert the ball head from below into the mounting with the shaft and push upwards until it snaps into place.
3.
Lock the lock in the handwheel.
4.
Attach cover to lock.
Checking the lock is closed
Before driving with a caravan or trailer, check whether the ball head is correctly locked, as otherwise it can lead to instability when driving and accidents.
<
By shaking the ball head, make sure that this is securely mounted.
If the ball head is not securely mounted, check the following points:
> Green marking on the handwheel points to the white area on the ball head.
> Handwheel is flush against the ball head.
> The lock is closed and the key removed.
If all points have been fulfilled and the ball head is despite this not firmly mounted, do not use the trailer coupling and get it checked by Service.
Removing the ball head
1.
Remove cover cap from the lock.
2.
Insert the key and open the lock in the handwheel.
The key is clamped in the lock.
3.
Hold ball head steady.
4.
Pull out the handwheel, arrow 1 and turn in arrow direction 2, as far as it will go.
5.
Take ball head out of the mounting by pulling downwards.
6.
Insert cover stopper in the mounting.
7.
Stow ball head in luggage compartment again.
Note care instructions on page
Before a journey
Trailer nose weight
Do not undercut the minimum trailer nose weight of 25 kg, approx. 55 lb. The nose weight limit is given on page
should be kept close to this limit.
The nose weight affects the vehicle and thus increases its weight. The weight of the trailer tow hitch and the nose weight reduce the maximum payload of your MINI. Please ensure that these do not cause the gross weight limit of the towing vehicle to be exceeded if a trailer is being towed.
Loads
When loading the trailer, make sure that the weight is kept as low as possible and stowed if possible close to the axle.
A low centre of trailer gravity makes the outfit much more stable and safe to drive.
Do not exceed either the trailer's permitted gross weight or the specified permitted towing load for the vehicle. The smaller value is the limit which should be adhered to.
Tyre pressures
Check the vehicle's and the trailer's tyre pressures carefully. For the car, the tyre inflation
pressures for heavy loads apply, page 142 . After
each correction of the tyre pressures, reinitialise
the Run Flat Indicator, see page 72
. For the trailer, comply with the manufacturer's specifications.
Run Flat Indicator
Reinitialise the Run Flat Indicator after a trailer
has been attached or detached, see page 72
.
Exterior mirrors
Two exterior mirrors which bring both rear corners of the trailer into your field of view are required by law. Mirrors of this kind can be
101
DRIVING HINTS Driving precautions obtained from your MINI Service Centre as optional accessories.
Electrical consumers
When towing a caravan, try to avoid operating electrical equipment for too long at a time, in order to limit the drain on the vehicle's battery.
The power output of the trailer's rear lights must not exceed the following values:
Flashing turn indicators: 42 W each side
Tail lights: 60 W each side
Brake lights: 42 W total
Rear fog lights: 42 W total
Reversing lights: 42 W total.
Before starting a journey, check that the trailer's rear lights are operating correctly.
As otherwise, there is a risk of endangering other road users.
<
Towing a trailer
Adapt your speed accordingly when towing a trailer. Dependent upon design and load, some trailers will start to snake at and above speeds of approx. 80 km/h, approx.
50 mph.
<
When towing a trailer, increase the inflation pressure by 0.2 bar and do not exceed speeds of 100 km/h, 60 mph, otherwise the increased axle weight could damage the tyres. Do not exceed the maximum possible inflation pressure indicated on the tyres.
<
Counteracting snaking
If the trailer nevertheless begins to snake, the outfit can only be stabilised by braking hard immediately. Only attempt to steer out of the situation if this is absolutely essential, and make any steering movements as cautiously as possible and without endangering other road users.
Uphill gradients
In the interest of safety and to avoid holding up other traffic, do not attempt to climb gradients steeper than 12% when towing a trailer. If a supplementary permit for heavier trailer loads
102 has been obtained, the limit is 8%, see page
.
Downhill gradients
Special care must be taken when descending gradients, where a trailer is more susceptible to snaking.
Before starting to descend, always change down to the next lower gear, if necessary as far as first gear, and drive down the hill slowly.
Saving fuel
Fuel consumption depends on various factors.
Certain measures, driving style and regular maintenance can influence the fuel consumption and the burden on the environment.
Remove unnecessary loads
Extra weight inflates fuel consumption.
Remove add-on parts after use
Remove auxiliary mirrors, roof racks and rearmounted racks after use.
Add-on parts on the vehicle interfere with its aerodynamic performance and inflate fuel consumption.
Check tyre pressures regularly
Check and, if necessary, correct tyre inflation pressures at least twice a month and before setting off on a longer journey.
Insufficient tyre inflation pressure enlarges the rolling resistance and thus increases fuel consumption and tyre wear.
Drive off immediately
Do not warm up the engine with the car at a standstill; it is preferable to set off straight away, driving at moderate engine speeds. A cold engine will then reach its operating temperature faster.
Driving precautions
DRIVING HINTS
Drive with foresight
Avoid accelerating and braking unnecessarily.
To do so, maintain an appropriately large gap between your car and the vehicle in front.
An anticipatory and even driving style can reduce fuel consumption.
Avoid high engine speeds
Only use 1st gear for driving off. From 2nd gear onwards, accelerate quickly to the appropriate engine speed and speed. In doing so, avoid high engine speeds and upshift at an early stage.
When you have reached the desired final speed, shift to the highest possible gear and drive at constant speed.
As a general principle, the following applies: driving at lower engine speed lowers fuel consumption and reduces wear.
The shift point indicator * displays the gear with the most favourable fuel consumption, page
.
Use the coasting mode
On approaching a red traffic light, take your foot off the accelerator and allow the car to roll in the highest possible gear.
On downward stretches, take your foot off the accelerator and allow the car to roll in the appropriate gear.
In the coasting mode, the flow of fuel is cut off automatically.
Switch off the engine during longer stops
When you stop the car for longer periods, e.g. at traffic lights, railway crossings or in traffic jams, switch off the engine.
The automatic start/stop function * switches the engine off automatically during a stop. For more information on the automatic start/stop function, refer to page
.
Have maintenance carried out
Have the vehicle serviced regularly to achieve optimal economy and service life. The manufacturer of your MINI recommends having this maintenance work carried out by a MINI Service
Centre. See also the MINI Maintenance System,
Driving on rough tracks
Your MINI will feel at home on all kinds of roads and tracks. It combines four-wheel drive* with the benefits of a conventional passenger vehicle.
Do not drive over rough terrain, otherwise the vehicle could incur damage.
<
For your own safety and that of your passengers, and to protect your vehicle against damage, observe the following points carefully when driving on rough tracks:
> Familiarise yourself with the vehicle before setting out in it, and never consciously take risks.
> Drive at a speed that is appropriate for the prevailing road conditions. The steeper and more uneven the road, the slower you should drive.
> Before setting out on very steep uphill or downhill gradients, check that the engine oil and coolant levels are near to the maximum
> Watch out for obstructions such as stones and potholes, and try to drive round them if possible.
> When driving over crests and on bumpy roads, avoid causing the vehicle's underbody to make contact with the surface. The vehicle's maximum ground clearance is approx. 15 cm, approx. 6 in. Please note that the ground clearance may vary according to the vehicle's load and operating conditions.
103
DRIVING HINTS Driving precautions
> Only drive through water on roads up to a maximum depth of 30 cm, 1 ft. Proceed no faster than walking pace but do not stop.
> After driving through water, press the footbrake several times at low speed; this will generate enough heat to dry the brakes off and ensure that the braking effect is not impaired by moisture.
> Depending on the properties of the road or track, it may be helpful to activate DTC briefly, see Dynamic Traction Control DTC on page
> If the wheels under one side of the vehicle spin, press the accelerator down far enough to prompt the driving stability control systems to distribute the propulsive power appropriately between the individual wheels.
After driving on rough tracks, please observe the following points, to uphold the safety of your vehicle:
> Clean coarse dirt off the body.
> Remove mud, snow, ice, etc. from the wheels and tyres, and check the tyres for damage.
104
Driving precautions
DRIVING HINTS
105
Rock Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
Entertainment Radio MINI CD
Radio MINI CD
Switching radio on/off
Press rotary knob. The radio selects the most recently selected audio source:
> Radio
> CD
> External audio device
Listening to radio when ignition switched off
When the radio standby is switched off or switched off ignition, the radio functions are available for approx. 20 minutes.
To do this switch on the radio again.
cle.
<
To save the battery, ensure that the radio is switched off when you leave the vehi-
Adjusting the volume
The selected volume setting is saved for the currently used remote control.
Adjusting the minimum volume of traffic reports
This volume is retained for subsequent traffic reports. If other audio sources are set louder than the traffic reports, the volume increases accordingly during a report.
1.
Hold the button down until "REG ON" or
"REG OFF" is displayed.
2.
Press the button until "TP-V" is displayed, e.g.:
3.
Press the … button repeatedly until the desired volume is reached.
Setting volume for PDC* and gong
You can raise or lower the volume of the signal tones for PDC and the gong compared to the volume of the audio sources.
The signal tones have a fixed minimum and maximum volume that may not be exceeded.
1.
Hold the button down until "REG ON" or
"REG OFF" is displayed.
2.
Press the button repeatedly until "PDC" or
"GONG" is displayed.
3.
Press the … button repeatedly until the desired volume is reached.
Adjusting the speed-related volume
The speed-related volume adjustment increases the volume automatically with increasing speed.
You can set various levels for the increase of the volume.
1.
Hold button down until "REG ON" or "REG
OFF" is displayed.
2.
Press button repeatedly until "SPEED
VOL" is displayed, e.g.:
3.
Press … button repeatedly until the speed-related volume has been set.
Resetting settings
The following functions are always jointly reset:
> Volume for traffic reports:
To level 0
> Volume for PDC and gong:
To level 0
108
Radio MINI CD
Entertainment
> Speed-related volume:
To level 3
To reset these settings:
1.
Hold button down until "REG ON" or "REG
OFF" is displayed.
2.
Press the button repeatedly until
"RESET?" is displayed.
3.
Press the button.
1.
Press
2.
Press button repeatedly until "TONE LIN?" is displayed.
3.
Press the button.
Displaying the time
Press the button.
The time can be displayed for approx. 8 seconds when the ignition is switched off.
.
Setting tone
You can choose between the following settings:
> Bass: deep tone setting.
> Treble: high tone setting.
> Fader: volume distribution front/back.
> Balance: volume distribution left/right
The volume distribution front/back - left/right as well as the bass and treble settings remain the same even after changes of the audio sources.
The settings for bass and treble are saved for the currently used remote control.
Setting treble, bass and volume distribution
1.
Press the button.
"BASS" is displayed.
2.
Keep pressing button until the desired tone setting is displayed. Treble, fader or balance.
3.
Press … button repeatedly until the desired setting is made.
Resetting the tone settings
The tone settings are reset to the middle setting:
> Bass and treble for the current audio source
> Volume distribution front/rear and left/right for all audio sources
In order to reset the tone settings:
Radio
Your radio is designed for the wave ranges FM and AM.
Listening to radio
1.
Switching on radio, see page 108
.
2.
Press button repeatedly until the desired wavelength range is selected.
> AM: MW/MWA
> FM: FM1/FM2 and FMA
Selecting a station
The selected radio station is stored for the remote control currently in use.
Next station
Press the … button.
The next receivable station is selected.
TP switched on, see page 110 : The next traffic reports station is selected.
Selecting station manually via frequency
1.
Press the button.
On the display, in addition to the frequency or the station name, "m" is displayed.
2.
Press … button or hold it down.
109
Entertainment Radio MINI CD
Saving station with best reception
FM station
Press the button repeatedly until
"AUTOSTORE" is displayed.
It can take several seconds until the stations have been set.
MW station
1.
Press the button repeatedly until the desired memory level has been selected.
2.
Press the button repeatedly until
"AUTOSTORE" is displayed.
It can take several seconds until the stations have been set.
The station saved under station button 1 is set.
If you do not want to use AUTOSTORE, you can save respectively six stations of your choice in the memory levels FMA or MWA.
<
Sampling and selecting a station, Scan
You can sample all receivable stations approx. 10 seconds.
3.
Hold down desired … button until the station can be heard again after a short break.
The memory level and the selected button are shown on the left of the display, e.g.:
Retrieving saved stations
1.
Press button repeatedly until the desired wavelength range is selected.
2.
Press desired … button.
Traffic reports*
You can receive traffic reports, while you are listening to a CD, for example. For this, the TP function, Traffic Programme, must be switched on.
Switching on/off traffic reports
Press the button.
The status "TP ON" or "TP OFF" is shown on the display.
On the display, in addition to the frequency or the station name, "SC" is displayed.
Interrupting the SCAN and selecting a station:
Press the button.
Saving and recalling a station
Memory locations
You radio can save 30 stations:
> FM1, FM2, MW: six stations each of your choice
> FMA, MWA: the six stations with the strongest signals automatically
Memorising stations
1.
Press button repeatedly until the desired frequency range is selected.
2.
Select a station.
Setting volume for traffic reports, see page
.
Displays
If a station transmits traffic reports, "T" or "TP" is displayed after the station name or frequency.
> TP
Traffic reports switched on.
> T
Traffic reports switched off, however the set station transmits traffic reports.
> TP flashes
Traffic reports are switched on, however the received station does not transmit traffic reports or these cannot be received.
> No display
Traffic reports switched off, and the set station does not transmit traffic reports.
110
Radio MINI CD
Entertainment
Regional programmes*
Certain FM stations broadcast regional programmes all the time or at certain times of day.
If you have activated this function and the station is switched to a regional programme, the device remains tuned to the regional programme that you have selected.
1.
Hold button down until "REG ON" or "REG
OFF" is displayed.
2.
Press … button.
> "REG ON"
Regional programme switched on
> "REG OFF"
Regional programme switched off
Radio Data System RDS
The Radio Data System transmits additional information in the FM range. RDS stations therefore offer the following features:
> Where a radio station is broadcast on several frequencies, the frequency with the best reception is automatically selected.
> When the reception conditions are good, the station names are displayed.
> Additional information can be shown on the display such as text messages from the station.
> Some stations transmit the type of received programme, PTY, via RDS. This is briefly displayed when the station is selected, e.g. news reports, NEWS. With PTY emergency and catastrophe warnings can also be displayed.
Switching RDS on/off
Press the button.
The status "RDS ON" or "RDS OFF" is shown on the display.
Press button again to change the status.
Switching on/off PTY
1.
Hold button down until "REG ON" or "REG
OFF" is displayed.
2.
Press repeatedly until "PTY AUTO" or "PTY OFF" is displayed, e.g.:
3.
Press … button.
> "PTY AUTO": PTY switched on
> "PTY OFF": PTY switched off
The programme type is automatically shown on the display for several seconds with:
> a change of station.
> a change of programme type.
> a change of source to FM.
> switching on and off of radio.
CD player
Listening to CD
The CD player can also play CDs with compressed audio files, e.g. MP3.
Depending on the number of titles, it may take some time before the CD player starts.
1.
Switching on radio, see page 108
.
2.
Slide CD with labelled side upwards into the
CD drive.
If there is already a CD in the CD drive:
Press the displayed.
button repeatedly until "CD" is
Changing the track
Jumping tracks
Press … button repeatedly until the desired track is reached.
If there is a CD with compressed audio data, e.g.
MP3:
111
Entertainment Radio MINI CD
Next to "TR" the file is displayed, after it the track, e.g. file 5, track 3.
To change the file:
1.
Press the button.
On the display next to the CD display, "m" appears.
2.
Press … button repeatedly until the desired file is reached.
Fast forward/reverse
1.
Hold … down.
The tracks can be heard in distorted form.
2.
To interrupt fast forward/reverse, release the button.
Scanning and selecting tracks, Scan
All tracks in CD are automatically played in sequence for approx. 10 seconds:
Press the button.
Next to the CD display, "SC" appears in the display.
To interrupt the scan and select a track:
Press the button.
Random sequence, Random
Switching random generator on/off:
Hold button down until "RND" appears in display.
Slide CD out of the CD player
Press the button.
The CD is ejected part way out of the drive.
Operating displays
"NO DISC"
The CD drive is empty.
"CD ERROR"
The CD is incorrectly inserted or has a mechanical fault.
Notes
CD players are Class 1 laser products. Do not operate with damaged cover, as otherwise eye injuries can be caused.
Do not use CDs with retrospectively affixed labels, as otherwise these may become detached during playing as a result of heat generation and possibly cause irreparable damage to the system.
Only use round CDs with a standard diameter of
12 cm, approx. 5 in, and do not play CDs with adapter, e.g. single CDs, as otherwise the CDs or the adapter can jam and possibly can no longer be ejected.
Do not use combined CD/DVDs, e.g. DVD
Plus
, as otherwise the CD/DVD may jam and can no longer be ejected.
<
General faults
The CD players have been optimised for use in the car. They may react more sensitively to faulty CDs than devices designed for stationary use.
If a CD cannot be played, first of all check that it has been correctly inserted.
Humidity
High air humidity can cause condensation to form on the CD or focusing lens for the laser beam and temporarily prevent the CD being played.
Faults with individual CDs
If faults only occur with individual CDs, this may be due to one of the following causes.
Home burned CDs
Causes of faults in home burned CDs are for example non-uniform data production and burning processes and the low quality or ageing of the blank used.
Only label the upperside of CDs with a suitable pen.
112
Radio MINI CD
Entertainment
Damaged CDs
Avoid finger prints as well as dust, scratches and humidity.
Keep CDs in a sleeve.
Do not expose CDs to temperatures over 50 6/
122 7, high air humidity or direct sunlight.
CDs with copy protection
CDs are often provided by the manufacturer with copy protection. This can have the effect that CDs cannot be played or only be played with restrictions.
General care
If required, wipe the mirrored scanning side with a cloth available from specialist dealers in a straight line from the middle.
External audio device*
You can connect an external audio device, e.g. a
CD or MP3 player, and play back music via the vehicle's loudspeakers.
Connecting
MINI, MINI Convertible, MINI Clubman:
MINI Countryman:
Switching over to external audio device
Press the is displayed.
button repeatedly until "AUX"
Adjusting the volume
The volume of the external audio device may be higher or lower than the audio sources of the radio.
In order to adjust the volume of the external audio device to the volume of other audio sources:
1.
Press button repeatedly until "AUX LEV" is displayed, e.g.:
2.
Press … button repeatedly until the desired volume is reached.
You can select a level between 0 and 5.
It is recommended to select neutral tone settings on the external audio device and to set the volume to the mid range. The sound might vary depending on the quality of the audio files.
<
113
Entertainment Radio MINI Boost CD
Radio MINI Boost CD
Switching radio on/off
Press left rotary knob. The radio selects the most recently selected audio source:
> Radio
> Digital radio *
> CD
> External audio device
> USB-audio interface * .
Listening to radio when ignition switched off
When radio standby is switched off, the radio functions are still available for approx.
20 minutes.
To do this switch on the radio again.
cle.
<
To save the battery, ensure that the radio is switched off when you leave the vehi-
3.
Press the button.
4.
Press the button.
5.
Select the desired volume and press the right-hand knob.
Setting volume for PDC* and gong
You can raise or lower the volume of the signal tones for PDC or gong compared to the volume of the audio sources.
The signal tones have a fixed minimum and maximum volume that may not be exceeded.
1.
Press the button.
2.
Press the button if necessary.
3.
Press the button.
or
Adjusting the volume
Turn left rotary knob. The setting is stored for the currently used remote control.
As soon as you conduct a phone call via the hands-free call system, the radio automatically switches to silent mode.
<
Setting minimum volume for traffic reports
This volume is retained for subsequent traffic reports. If other audio sources are set louder than the traffic reports, the volume increases accordingly during a report.
1.
Press MODE button.
2.
Press the button.
114
Press the button.
4.
Select the desired volume and press the right-hand knob.
Adjusting the speed-related volume
The speed-related volume adjustment increases the volume automatically with increasing speed.
You can set various levels for the increase of the volume.
1.
Press the button.
2.
Press the button if necessary.
3.
Press the button.
4.
Select the desired volume and press the right-hand knob.
Radio MINI Boost CD
Entertainment
Setting volume for external audio devices
Your radio supports the option of connecting an external audio device, e.g. a CD or MP3 player, and play back music via the vehicle's loudspeakers. You can set the volume via the radio.
Connecting the external device, see page 121 .
In order to adjust the volume of the external audio device to the radio:
1.
Press the MODE button.
2.
Press the button.
3.
Press the button.
4.
Select the desired volume and press the right-hand knob.
Setting tone
You can choose between the following settings:
> Bass: deep tone setting.
> Treble: high tone setting.
> Balance: volume distribution left/right
> Fader: volume distribution front/back.
The tone settings are applied to all audio sources.
Setting treble, bass and volume distribution
1.
Press the button.
2.
Select the desired tone setting and press the right-hand knob.
3.
Make the desired setting and press the right-hand knob.
Resetting the tone settings
The tone settings are reset to the middle setting.
1.
Press the button.
2.
Press the button.
Time
Setting the time, date and date format
You can set the time, date and time format, see
.
Radio
Your radio is designed for the wave ranges FM and AM.
Listening to radio
1.
Switching on radio, see page 114
.
2.
If required press MODE button.
3.
Press the button.
4.
Press appropriate button repeatedly until the desired wavelength range has been selected.
> AM: MW/MWA
> FM: FM1/FM2 and FMA
Selecting a station
The setting is stored for the currently used remote control.
Next station
Press the … button.
The next receivable station is selected.
If TP is switched on, see page
: The next traffic reports station is selected.
115
Entertainment Radio MINI Boost CD
Selecting station manually via frequency
1.
Press the button.
2.
Press respective button to enter desired frequency.
Press the button.
Interrupting the scan and selecting a station:
Or with the right-hand knob:
1.
Press the button.
2.
Turn the right-hand knob until the desired frequency is reached.
Automatically updating the station with best reception
FM station
Hold the button down until
"Autostore" is displayed.
It may take several seconds until the stations are saved and one of these stations can be heard.
If TP is switched on, see page 117 : A traffic
reports station is selected.
MW station
1.
Press the button repeatedly until the desired MWA memory level has been selected.
2.
Hold the button down until
"Autostore" is displayed.
It may take several seconds until the stations are saved and one of these stations can be heard.
If you do not want to use Autostore, you can save respectively six stations of your choice in the memory levels FMA or MWA.
<
Scanning and selecting stations, Scan
You can sample all receivable stations approx. 10 seconds.
Press the button.
Saving and recalling a station
Memory locations
Your radio can save 42 stations:
> FM1, FM2, MW: six stations each of your choice
> FMA, MWA: the six stations with the strongest signals automatically
Memorising stations
1.
Press the appropriate button repeatedly until the desired frequency range is selected.
2.
Select a station.
3.
… Hold down desired button until the station can be heard again after a short break.
The memory level and the selected button are shown on the left of the display, e.g.:
Retrieving saved stations
1.
Press appropriate button repeatedly until the desired wavelength range has been selected.
2.
… Press desired button.
With the right-hand knob:
Turn the right-hand knob until the desired station is reached.
116
Radio MINI Boost CD
Entertainment
Traffic reports*
You can receive traffic reports, while you are listening to a CD, for example. For this, the TP function, Traffic Programme, must be switched on.
Switching on/off traffic reports
Press the button.
Setting volume for traffic reports, see page
Displays
If a station transmits traffic reports, "TP" is displayed after the station name or frequency.
> TP
Traffic programme is switched on.
> Traffic programme is switched off.
> TP flashes
The received station is not a traffic programme or traffic reports cannot be received.
Regional programmes*
Certain FM stations broadcast regional programmes all the time or at certain times of day.
If you have activated this function and the station is switched to a regional programme, the device remains tuned to the regional programme that you have selected.
1.
Press the button.
> When the reception conditions are good, the station names are displayed.
> Additional information can be shown on the display such as text messages from the station.
> Some stations transmit the type of received programme, PTY, via RDS. This is briefly displayed when the station is selected, e.g. news reports, NEWS. With PTY emergency and catastrophe warnings can also be displayed, e.g. "ALARM".
Switching RDS on/off
1.
Press the button.
2.
Press the button.
The name of the current station is displayed if this transmits RDS information.
Displaying programme type
1.
Press the button.
2.
Press the button.
2.
Press the button.
Radio Data System RDS
The Radio Data System transmits additional information in the FM range. RDS stations therefore offer the following features:
> Where a radio station is broadcast on several frequencies, the frequency with the best reception is automatically selected.
Digital radio*
The digital radio provides you with additional stations that are transmitted with a higher sound quality.
Several stations are combined to form a group.
Each station can transmit additional information such as information about the station, for example, or the name of the artist performing the current music track.
Some stations feature additional programmes; sports stations can transmit different sports events simultaneously, for instance. You then have the option of choosing a particular sports event.
A digital radio network must be available in order to receive digital stations.
117
Entertainment Radio MINI Boost CD
Listing to digital radio
1.
Press the MODE button.
2.
Press the button.
You will hear the most recently selected station.
To show the station list of the current group:
Press the button.
>
Press the button.
The current group and its associated station are displayed.
Changing group via buttons on radio:
Press the … button.
The stations can be changed via the buttons on the steering wheel.
Updating receivable stations
If you leave the transmission area of the originally received station, you can update the display of receivable stations.
1.
Keep pressing the button until
"ASTORE" is displayed.
1 Ensemble
2 Transmitter of selected group
3 * Station with additional programmes
Changing stations
Turn the right-hand knob until the desired station is reached.
You can select other stations:
>
Press the button.
Up to six stations can be selected. After the
"DAB" button is pressed again, six other stations are available.
>
Press the button.
More groups can be displayed, each group can contain several stations.
> : press right-hand knob to open group
> : press right-hand knob to close group
2.
Press the button.
It can take several seconds until the groups have been saved.
Up to 12 groups each with 12 stations can be saved.
Scan stations, Scan
All stations in the present group are briefly sampled on after another.
The stations of another group are then sampled.
Press the button.
Interrupting the scan and selecting a station:
Press the button.
118
Radio MINI Boost CD
Entertainment
Memorising stations
You can save 12 stations:
1.
Select station.
2.
… Hold down desired button until the station can be heard again after a short break.
Selecting frequency range
Some digital stations are transmitted digitally, other interregionally.
You can obtain more detailed information on the frequency ranges from your Service.
1.
Press the button.
2.
Selecting desired frequency range:
> "BAND 3" for transregional stations
> "L-BAND" for regional stations
3.
Press the right-hand knob.
Displaying additional information
Depending on a station's offer, additional information can be displayed, such as information about the station or the name of the artist for the current music track.
1.
Press the button.
2.
Press the button.
Hearing additional programmes
This symbol is shown if a selected station offers additional programmes. Sports stations, for example, may broadcast different sports events at the same time.
1.
Press the button.
2.
Select station.
3.
Select the additional programme.
If the programme is over, the radio switches to the selected station.
CD player
Starting CD player
It can take a while before the CD player starts.
1.
Switching on radio, see page 114
.
2.
Slide CD with labelled side upwards into the
CD drive.
If there is already a CD in the CD drive:
1.
If required switch on radio
2.
Press the MODE button.
3.
Press the button.
Changing the track
Jumping tracks
Press … button repeatedly until the desired track is reached.
With the right-hand knob:
Turn right-hand knob until the desired track is reached.
Fast forward/reverse
1.
Hold … down.
The tracks can be heard in distorted form.
2.
To interrupt fast forward/reverse, release the button.
Random sequence, Random
Press the button.
To quit the random generator:
Press the button.
Scanning and selecting tracks, Scan
Press the button.
119
Entertainment Radio MINI Boost CD
To interrupt the scan and select a track:
Press the button.
Selecting MP3 tracks
The CD player can also play CDs with compressed audio files, e.g. MP3 and WMA.
Selecting a track
1.
Press the button.
2.
Select the desired file and press the righthand knob.
>
>
: press right-hand knob to open file
: press right-hand knob to close file
3.
If required select other sub-files and press right-hand knob.
4.
Select the desired track and press the righthand knob.
You can scroll through the file during replay.
To change to the current track:
Press the button.
Track display
You can access any information available on the current track:
1.
Press button.
2.
Press button.
Slide CD out of the CD player
Press the button.
The CD is ejected part way out of the drive.
Operating displays
> "Insert CD"
The CD drive is empty.
> "Error CD"
The CD cannot be read or is defective.
> "Temp. CD"
Operating temperature too high.
Notes
CD players are Class 1 laser products. Do not operate with damaged cover or severe eye injuries can result.
Do not use CDs with retrospectively affixed labels, as otherwise these may become detached during playing as a result of heat generation and possibly cause irreparable damage to the system.
Only use round CDs with a standard diameter of
12 cm, approx. 5 in, and do not play CDs with adapter, e.g. single CDs, as otherwise the CDs or the adapter can jam and possibly can no longer be ejected.
Do not use combined CD/DVDs, e.g. DVD
Plus
, as otherwise the CD/DVD may jam and can no longer be ejected.
<
General faults
The CD players have been optimised for use in the car. They may react more sensitively to faulty CDs than devices designed for stationary use.
If a CD cannot be played, first of all check that it has been correctly inserted.
Humidity
High air humidity can cause condensation to form on the CD or focusing lens for the laser beam and temporarily prevent the CD being played.
Faults with individual CDs
If faults only occur with individual CDs, this may be due to one of the following causes.
Home burned CDs
Causes of faults in home burned CDs are for example non-uniform data production and burning processes and the low quality or ageing of the blank used.
120
Radio MINI Boost CD
Entertainment
Only label the upperside of CDs with a suitable pen.
Damaged CDs
Avoid finger prints as well as dust, scratches and humidity.
Keep CDs in a sleeve.
Do not expose CDs to temperatures over 50 6/
122 7C, high air humidity or direct sunlight.
CDs with copy protection
CDs are often provided by the manufacturer with copy protection. This can have the effect that CDs cannot be played or only be played with restrictions.
General care
If required, wipe the mirrored scanning side with a cloth available from specialist dealers in a straight line from the middle.
connectivity or contact Service for more information.
Connecting
MINI, MINI Convertible, MINI Clubman:
1 Connection for sound playback:
Jack plug 3.5 mm
2 USB interface *
MINI Countryman:
USB audio interface*
> iPod /iPhone or USB devices, e.g. MP-3 player, USB memory stick: connecting through USB audio interface
> Music player of the iPhone/ mobile phone:
Connection via snap-in adapter * , see page
.
> Only an iPod/iPhone can be connected with the vehicle. Replay from the iPod/iPhone to the USB audio interface is only possible if no iPhone is inserted in the snap-in adapter.
> Common audio files, such as MP3, AAC and replay lists M3U can be played. Depending on the configuration of the audio files, e.g. bit rates higher than 256 kbps, fault-free playback cannot always be assured.
> Music tracks with integrated Digital Rights
Management (DRM) cannot be played.
The large number of audio devices available on the market means that the vehicle cannot guarantee to support the operation of all audio devices/mobile phones. Go to www.mini.com/
1 USB interface *
2 Connection for sound playback:
Jack plug 3.5 mm
Apple iPod/iPhone
Use the special cable adapter for Apple iPod/ iPhone to make the connection. The cable adapter is required for a proper connection.
For more information, contact MINI Service or consult the Internet: www.mini.com/connectivity
For audio playback over the car's loudspeaker system, connect the iPod to connections 1 and 2.
The menu structure of the iPod/iPhone is supported by the USB audio interface.
121
Entertainment Radio MINI Boost CD
USB device
For audio playback over the car's loudspeaker system, connect the USB device to connection 2.
After initial connection, the track information is transmitted to the vehicle. The duration depends on the USB device and the number of tracks.
Track information from up to four USB devices or for approx. 20,000 tracks can be saved in the vehicle.
Starting sound playback iPod
1.
Press MODE button.
2.
Press the button.
USB device
1.
Press MODE button.
2.
Press the button.
Changing the track
Jumping tracks
Press … button repeatedly until the desired track is reached.
With the right-hand knob:
Turn right-hand knob until the desired track is reached.
Fast forward/reverse
1.
Hold … down.
The tracks can be heard in distorted form.
2.
To interrupt fast forward/reverse, release the button.
Random sequence, Random
Press the button.
The current track is played to the end.
The tracks on the current CD are played once each in random order.
To quit the random generator:
Press the button.
Selecting a track
Select desired list, e.g."LIST":
1.
Press the button.
2.
Select the desired file and press the righthand knob.
>
>
: press right-hand knob to open file
: press right-hand knob to close file
3.
If required select other sub-files and press right-hand knob.
4.
Select the desired track and press the righthand knob.
You can scroll through the file during replay.
To change to the current track:
Press the button.
Track display
You can access any information available on the current track:
Press the button.
Adjusting the volume of the iPod*
The volume of the iPod may be higher or lower than the audio sources of the radio.
In order to adjust the volume of the external audio device to the volume of other audio sources:
1.
Press the button.
2.
Select the desired volume and press the right-hand knob.
122
Radio MINI Boost CD
Notes
> The USB/audio interface supplies the connected audio devices with current if the audio device supports this. For this reason, do not connect the audio device to the socket in the vehicle during operation.
> Do not expose audio devices to extreme ambient conditions, e.g. very high temperatures, see the operating instructions for the audio device.
> Do not connect any devices such as fans or lamps to the USB audio interface.
> Do not connect up USB hard drives.
Entertainment
123
Connect Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
COMMUNICATION Telephone
Telephone *
Overview
Principle
Mobile phones or other external devices such as audio players can be connected to the vehicle over Bluetooth.
Your MINI is equipped with a mobile phone preparation. As soon as you have performed a one-off pairing procedure in the vehicle with a suitable mobile phone, you will be able to operate it via the radio, using the buttons * on the steering wheel and by voice control * .
Some functions might need to be enabled by your mobile phone provider.
Only make inputs when it is safe to do so without risk to yourself or other road users. Do not hold the mobile phone in your hand while driving; use the hands-free unit instead. You could otherwise be distracted and put both the occupants of your vehicle and other road users at risk.
<
Snap-in adapter*
The snap-in adapter, see page
:
> Provides a holder for the mobile phone.
> Charges the battery.
> Establishes a connection to the vehicle's external antenna.
This ensures better network reception and consistent sound quality.
Do not use the keypad on the mobile phone to operate the mobile phone connected to the vehicle as this can lead to malfunctions.
Suitable mobile phones
For detailed information about which mobile phones and external devices with Bluetooth interface are supported by the mobile phone preparation, go to www.mini.com/connectivity.
126
Using the mobile phone via the radio
Telephone
COMMUNICATION
To call up the menu shown above, see page
.
1 Make and receive calls
> "NR": dialling a phone number
> "A-Z": phone book
> "TOP8": most frequent numbers dialled
> "LAST8": most recent numbers dialled
> "CALLS": calls accepted
> "MISSED": calls not accepted
2 Highlight to select a function
3 Mobile phone network reception:
Flashes when a call is in progress
4 Pair a new mobile phone, delete the pairing data for a mobile phone or switch Bluetooth
5 Time
6 Back
7 Function buttons for confirming the functions displayed above
8 Redial, accept call, start call, end call and switch to Telephone menu
9 Selecting and confirming a function
> Turn: select function or number
> Press: activate function or number
127
COMMUNICATION Telephone
> "TEL": phone
> "COMP": computer
> "CONFIG": settings
11 Radio on/off, volume
> Press: switch radio on/off
>
12 CD eject
This symbol appears on the radio display when a call is made or received via the handsfree unit.
To deactivate the Bluetooth connection:
1.
Press the MENU button.
2.
Press the button.
3.
Press the button.
4.
Press the button.
5.
Press the button.
To reactivate the Bluetooth connection:
1.
Press the button.
Pairing/Unpairing a mobile phone
Overview
Pairing data for up to four mobile phones can be stored in the vehicle simultaneously. Each mobile phone paired is identified automatically as soon as it is inside the vehicle when the engine is running or the ignition is switched on.
Conditions
> Compatible mobile phone, see page 126
> Mobile phone operational
> Bluetooth activated on the vehicle, see page
, and on the mobile phone
> Bluetooth pre-adjustments might have to be made on the mobile phone, e.g. £connection not with authorisation or visibility, see the operating instructions for the mobile phone
> Number with at least 4 but no more than 16 digits set as the Bluetooth passkey. Only required for one-off pairing.
> Ignition switched on.
Deactivating/activating Bluetooth connection
Bluetooth is not permitted everywhere. Comply with national legislation.
128
2.
Press the button.
Pairing and connection
Only pair the mobile phone while the vehicle is at a standstill so as not to endanger the vehicle's occupants and other road users as a result of being distracted.
<
Switching on the ignition
1.
Insert the remote control all the way into the ignition switch.
2.
Switch on the ignition, pressing the start/ stop button without operating the brake or clutch pedal.
Preparation on the radio display
3.
Press the MENU button.
4.
Press the button.
Telephone
COMMUNICATION
5.
Press the button.
11.
Use the function buttons 0-9 to enter the same Bluetooth passkey entered on the mobile phone.
To delete the last digit:
6.
Press the button.
Turn the right-hand rotary knob to show the
Bluetooth name of your vehicle on the display.
Preparation via the mobile phone
7.
Further procedures must be performed on the mobile phone; these may vary depending on the type of mobile phone. See the operating instructions for your mobile phone, e.g. under locating, connecting or pairing Bluetooth devices. The Bluetooth name of the vehicle is shown on the mobile phone display.
8.
Select the Bluetooth name of the vehicle on the mobile phone display.
:
Pairing
You are prompted to enter the same Bluetooth passkey on the mobile phone or radio display.
Depending on the type of mobile phone, you will have around 30 seconds to enter the Bluetooth passkey on the mobile phone and on the radio display.
Information on the display if the Bluetooth passkey can be entered on the radio:
9.
Enter the Bluetooth passkey using the numeric keys on the mobile phone.
10.
Press the button to enter the Bluetooth passkey on the radio.
Press the button.
12.
Press button to confirm the Bluetooth passkey.
Display after a few seconds:
13.
Press the button if necessary.
Display after the mobile phone has been paired:
If pairing was successful, the mobile phone appears in the first position in the list of mobile phones.
If pairing is not successful: What to do if…, see
To repeat pairing:
1.
Press the button.
2.
Repeat steps 6 to 13.
If registration is repeatedly unsuccessful:
> Suitable mobile phones at: www.mini.com/ connectivity
>
To display the phone number for the hotline:
Press the button.
129
COMMUNICATION Telephone
Turn the right-hand knob to display the phone number for the hotline and the information required for pairing on the display.
After pairing for the first time
> Mobile phone is detected/paired in the vehicle after a short delay when the engine is running or radio standby switched on.
> Once the mobile phone has been identified, phone book entries from the mobile phone and/or SIM card * are transferred from the telephone as appropriate for the device concerned.
> Some mobile phones may require certain settings, authorisation or secure connection, see operating instructions of the mobile phone.
Connecting a certain mobile phone
If more than one mobile phone is detected by the vehicle, the mobile phone furthest up the list is connected. If another mobile phone is to be connected, this can be selected.
The connected mobile phone is identified on the radio display by the following symbol:
To change the order in which the mobile phones appear in the list:
1.
Press the MENU button.
2.
Press the button.
3.
Press the button.
4.
Turn the right-hand rotary knob until the mobile phone whose position in the list you wish to change is displayed.
5.
Press the button as often as necessary until the desired chapter is reached.
Unpairing a mobile phone
1.
Switch off the mobile phone.
2.
Press the MENU button.
3.
Press the button.
4.
Press the button.
5.
Turn the right-hand rotary knob to show the required mobile phone on the radio display.
6.
Press the button.
7.
Press the button to confirm the message on the display.
What to do if ...
Information about compatible mobile phones, see page 126 .
Unable to pair or connect mobile phone.
> Is Bluetooth activated on the vehicle and on the mobile phone? Activate Bluetooth in the vehicle and on the mobile phone.
> Do the Bluetooth passkeys on the mobile phone and vehicle agree? Enter the same passkey on the mobile phone and via the radio.
> Does it take more than 30 seconds to enter the passkey? Repeat the pairing procedure.
> Too many Bluetooth devices paired to the mobile phone? If necessary delete the pairing information on the mobile phone for some other device.
> Is the mobile phone running in power economy mode or is the battery charge low?
Charge the mobile phone in the snap-in adapter * or using the charger cable.
> Dependent upon the mobile phone, it might only be possible to connect one device to the vehicle. Unpair the connected device
130
Telephone
COMMUNICATION from the vehicle and pair and connect just one device.
> Has the mobile phone stopped responding?
Switch the mobile phone off and back on again. Repeat the pairing procedure.
> Delete coupling on mobile and possibly on radio and try again.
Phone book entries are not being displayed at all, only some of the entries are being displayed or the entries are incomplete:
> Phone book entry transfer has not been completed.
> It might be the case that only the phone book entries from the mobile phone or the
SIM card * have been transferred.
> Phone book entries with special characters may sometimes not be displayed.
> Too many phone book entries to be saved.
> Is the phone book entry data volume too great, e.g. due to additional information such as notes? Reduce the data volume.
The quality of the telephone connection is poor.
> The strength of the Bluetooth signal can be adjusted to suit the mobile phone.
> Place the mobile phone in the snap-in adapter * or in the area of the centre console.
> Set the volume of the microphone and loudspeaker separately.
If all the points in the list have been checked and you are still unable to run the required function, contact the hotline or Service.
Operation
Overview
The following functions can be operated via the radio:
> Accepting/rejecting a call
> Dialling a phone number
> Dialling a phone number from the phone book
> Dialling stored phone numbers, e.g. from the list of received calls
> Ending a call
With the ignition switched off but in the radio ready state, e.g. after the remote control has been removed, you can continue a call via the hands-free unit for up to 25 minutes.
Adjusting the volume
Turn the knob until the desired volume is reached.
The volume for an incoming call and the call volume can be set separately.
The setting is saved for the remote control currently in use.
Incoming call
Receiving a call
If the phone number of the person calling you is stored in the phone book and the number is not withheld, the name under which it is stored is displayed.
Accepting a call
Press the button on the radio or on the steering wheel.
Alternatively:
Press the button.
131
COMMUNICATION Telephone
Rejecting a call
Press the button.
Ending a call
Press the button on the radio or on the steering wheel.
Alternatively:
DTMF suffix dialling
DTMF suffix dialling is used to access network services or to control devices, e.g. to pick up messages on an answering machine remotely.
The DTMF code is required.
This function is available if a connection exists and calls are made via the hands-free unit.
1.
Press the button.
Press the button.
Phone number entry
Dialling a number
1.
Press the MENU button.
2.
Press the button.
3.
Press the button.
4.
Enter the required phone number using buttons 0-9.
To delete the last digit if necessary:
Press the button.
5.
Press the button on the radio or on the steering wheel.
Alternatively:
Press the right-hand rotary knob to dial the phone number.
For your phone number to be displayed to the person you are talking to, the caller display function must be enabled by your service provider.
2.
Enter the required code using buttons 0-9.
3.
Press and hold down the button on the right or left to enter special characters if necessary.
Dialling a phone number from the phone book or in the list of saved phone numbers
Dialled phone numbers, incoming calls and phone book entries are saved in lists if the mobile phone is connected to the vehicle over
Bluetooth. If there is a phone book entry for the caller, his or her name is displayed instead of the phone number.
Select the required contact from the list and establish the connection.
Five lists are available:
> "A-Z"
The entries from the phone book on the SIM card * or the mobile phone, consisting of name and number, are sorted alphabetically.
> "TOP8"
The eight numbers from the phone book which are dialled most frequently are saved in the Top 8 list automatically.
> "LAST8"
The last eight numbers dialled are saved automatically. The last number dialled appears at the top of the list.
132
Telephone
COMMUNICATION
> "CALLS"
The phone numbers of the last eight calls received are stored. In order for this to work, it has to be possible for the caller's number to be transferred.
> "MISSED"
The phone numbers of the last eight missed calls are saved. In order for this to work, it has to be possible for the caller's number to be transferred.
Dialling a phone number from the phone book
The A-Z list is available for phone book entries. If entries with different names but the same phone number are transferred from the mobile phone to the vehicle, only one entry is displayed.
The way in which the phone book entries appear on the radio display can differ from their appearance on the mobile phone display, e.g. with regard to the order of first name and surname.
1.
Press the MENU button.
2.
Press the button.
3.
Press the button.
The arrows indicate that additional letters can be displayed.
Turn the right-hand rotary knob to display more letters.
4.
Turn the right-hand rotary knob to select the first few letters of the required entry.
5.
Press the required button if necessary.
The phone number is dialled.
To display all entries:
1.
Turn the right-hand rotary knob to select the first few letters of the required entry and press the right-hand rotary knob.
2.
Turn the right-hand rotary knob to select the required entry and press the right-hand rotary knob.
The phone number is dialled.
You can also dial the phone number using the button on the steering wheel or on the radio:
Press the button.
Editing and dialling a number from the phone book
The phone number associated with an entry can be edited before making a call. This change is not saved in the phone book.
1.
Select the entry.
2.
Press the button.
3.
Press the button to delete a digit if necessary.
4.
Enter more numbers using buttons 0-9.
5.
Press the right-hand rotary knob to dial the phone number.
Using the buttons on the steering wheel to dial a phone number from the phone book
1.
Press and hold down the button until the
Telephone menu is displayed.
2.
Press the arrow keys on the steering wheel to browse through the phone book.
3.
Press the button to dial the phone number.
133
COMMUNICATION Telephone
Dialling phone numbers saved in a list
To select an entry and establish a connection:
1.
Press the MENU button.
2.
Press the button.
From the hands-free unit to the mobile phone
In some cases calls made and received using the hands-free unit can be switched over to the mobile phone, dependent upon the model.
Follow the instructions on the mobile phone display, see also the operating instructions for the mobile phone.
3.
Press the required button to select one of the four lists.
4.
Turn the right-hand rotary knob to select an entry and press the same knob to dial the phone number.
Deleting individual entries
1.
Select the desired entry from the list.
2.
Press the button.
Displaying call duration
To display the duration during a call:
Press the button.
Hands-free unit
General
Calls made and received using the hands-free unit can be switched over to the mobile phone and vice versa.
From the mobile phone to the handsfree unit
Calls started outside the Bluetooth range of the vehicle can be switched over to the hands-free unit if the ignition is switched on.
Depending on the type of mobile phone, switchover to hands-free mode may take place automatically.
If switchover is not automatic, follow the instructions on the mobile phone display, see also the operating instructions for the mobile phone.
Operation by voice control*
Principle
> You can use the mobile phone without taking your hands off the steering wheel.
> In many cases, entries are made by saying commands or asking questions.
> {...} identifies commands for the voice control system.
> {{...}} identifies replies by the voice control system.
Speaking commands
Activating voice input
1.
Press and release the button on the steering wheel.
An acoustic signal indicates that you can say commands. Display on the radio:
2.
Issue the command.
Completing voice input
Press and release the button on the steering wheel or
{Cancel}.
134
Telephone
COMMUNICATION
Possible commands
Having possible commands read aloud
Press the button on the steering wheel.
{Help}.
Possible commands are read aloud.
You can say each digit individually or say the entire number as a block to speed up the input process.
Using alternative commands
There are often several different commands available for performing the same function, e.g.:
{Dial name} or {Name}.
An example: dialling a phone number
1.
Press and release the button on the steering wheel.
2.
{Dial number}
3.
The system says: {{Please say the number}}
4.
E.g. {123 456 7890}
5.
The system says: {{123 456 7890. Continue?
}}
6.
{Dial}
System says: {{Dialling number}}
Making a call
Dialling a phone number
1.
{Dial number}.
2.
Say the phone number.
3.
{Dial}.
The connection with the desired subscriber is established.
Correcting a phone number
A block of digits can be deleted once the system has repeated the digits concerned.
{Correct number}.
The command can be repeated as often as you wish.
Deleting a phone number
{Delete}.
All previously entered digits are deleted.
Redial
{Redial}.
Voice-activated phone book*
Depending on the equipment available in your vehicle, it may be necessary to create a separate voice-activated phone book.
The names and numbers in the voice phone book are independent of the mobile phone's memory or SIM card. Therefore, phone numbers saved in the mobile phone or on the SIM card cannot be called up using voice input or saved to these locations using voice input.
Saving an entry
1.
{Save name}.
2.
Say the name. Do not speak for more than approx. 2 seconds.
3.
When prompted by the system, say the phone number.
4.
{Save}.
Deleting an entry
1.
{Delete name}.
2.
When asked to do so, say the name.
3.
Confirm request with {Yes}.
Deleting all entries
1.
{Delete phonebook}.
The dialogue for deleting the phone book is called up.
2.
Confirm request with {Yes}.
3.
Confirm the repeated query with {Yes}.
135
COMMUNICATION Telephone
Reading out and selecting entries
1.
{Read phonebook}.
The dialogue for reading out the phone book is called up.
2.
{Dial number}, when the desired entry is read aloud.
Selecting an entry
1.
{Dial name}.
2.
When asked to do so, say the name.
3.
Confirm request with {Yes}.
Adjusting the volume
Turn the knob whilst you are speaking.
> The volume remains set to this level even if the volume of other audio sources is adjusted.
> The volume setting is saved for the remote control currently in use.
Notes
Do not use voice input for emergency calls. In stress situations, the spoken language and voice pitch can change. This delays establishment of a telephone connection unnecessarily.
Ambient conditions
> Say commands, digits and letters fluently and in a normal volume, intonation and speed.
> Always say the commands in the language of the voice control system.
> Keep doors, windows, glass roof * /panorama glass roof * or soft top * closed to avoid noise interference.
> Avoid ambient noise in the vehicle while you are speaking.
MINI Contact*
Several service phone numbers can be displayed when the ignition is switched on.
> "MoblSr Call": MINI Roadside Assistance * , if you need help in the event of a breakdown.
> "Dealer": MINI Service, if you need to make an appointment for a service.
> "MINI Cust Sr": MINI hotline * for information about any aspect of your vehicle.
Displaying phone numbers
1.
Press the MENU button.
2.
Press the button.
3.
Turn the right-hand rotary knob until the phone number you require is displayed.
Snap-in adapter*
Installation location
In the centre armrest
Inserting the snap-in adapter
1.
Press the button and remove the cover.
136
2.
Insert the snap-in adapter at the front, arrow 1, and press down, arrow 2, until it engages.
Telephone
COMMUNICATION
Inserting the mobile phone
1.
Dependent upon the mobile phone model, you might need to remove the protective cap from the antenna connector and from the USB connection on the mobile phone.
2.
Push the mobile phone with the keys upwards towards the electrical connections and press down until it engages.
Removing the mobile phone
Press the button and remove the mobile phone.
137
Move Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
MOBILITY Refuelling
Refuelling
Fuel filler flap
Opening
1.
Open the fuel filler flap.
2.
Turn the fuel filler cap anticlockwise.
3.
Place the tank cap in the holder on the flap.
Closing
Fit the tank cap and turn clockwise until it is clearly heard to click into place.
Do not jam the strap attached to the tank cap, as otherwise the tank cap cannot be closed properly and fuel vapours can escape.
<
Manually releasing the fuel filler flap
In the event of an electrical fault, you can release the fuel filler flap manually:
2.
Pull the green knob featuring the petrol pump symbol, arrow 2.
The fuel filler flap opens.
Note when refuelling
When handling fuel, comply with the safety regulations displayed by filling stations, otherwise there is a risk of injury or damage.
<
When refuelling, insert the filler nozzle fully into the filler neck. Avoid lifting the filler nozzle during refuelling, otherwise
> The supply of fuel will be cut off prematurely
> Fuel vapour and fumes will be fed back less effectively
The fuel tank is full two applications after the filler nozzle cuts out for the first time.
Fuel tank capacity
If the remaining range is below 50 km, approx. 30 miles, refuel the car, otherwise the engine's functions are not assured and damage may occur.
<
Approx. 47 litres, approx. 11.0 gal, including a reserve of 8 litres, approx. 1.8 gal.
1.
Open the luggage compartment trim panel, arrow 1.
Fuel
Petrol
For optimum fuel consumption, the petrol should be sulphur-free or at least low-sulphur.
Fuels that are labelled as containing metal at the petrol pump may not be used.
Do not use petrol or petrol with metallic additives, e.g. manganese or iron, as otherwise there may be permanent damage to the catalyst and other components.
<
140
The vehicle can be refuelled with fuel containing a maximum of 10 % ethanol, i.e. E10.
Do not use E85, i.e. fuel that contains 85 % ethanol, or FlexFuel. Otherwise the engine and the fuel supply system will be damaged.
<
Petrol quality
The engine is knocking adjusted. Therefore different petrol qualities can be used.
The manufacturer of your MINI recommends:
> Premium-grade fuel: 95 RON.
> Cooper S 98 RON
Fuel grades with 91 RON or higher are permissible.
Do not fill the tank with fuel under
91 RON, as otherwise the engine and the fuel supply system will be damaged.
<
Diesel
Do not use rapeseed methyl ester RME, biodiesel or petrol. If the wrong type of fuel has been added, do not start the engine, otherwise you risk causing damage to it.
<
The filler neck is designed to accommodate the filler nozzles of diesel fuel pumps.
Contact MINI Service if the wrong type of fuel has been added.
Diesel quality
The engine of your MINI is designed to run on:
Diesel oil to DIN EN 590 standard.
Winter-grade diesel oil
To ensure that the diesel engine operates reliably during the cold season of the year, it must be run on winter-grade diesel oil, which garages usually sell during the period in question. Fuel filter heating is installed as standard equipment to prevent the fuel solidifying during operation.
Do not incorporate any additives, including petrol, as these could cause damage to the engine.
<
Refuelling
MOBILITY
141
MOBILITY Wheels and tyres
Wheels and tyres
Tyre pressures
Information for your safety
The condition of the tyres and maintenance of the correct tyre pressures not only influence tyre life but are also decisive factors in road safety and ride quality.
Checking pressures
Check the tyre pressures regularly: but at least twice a month and before setting out on any long journey. Incorrect tyre pressures can adversely affect the car's roadholding and cause tyre damage, which could result in an accident.
<
After correcting tyre pressures, reinitialise the Run Flat Indicator, page
<
Tyre pressure values
for tyres that may be covered by the label – by size, speed category and load rating/load index
– but not explicitly mentioned on the label may be different, please obtain adequate inflation pressures in accordance with the tyre manufacturer's specifications at your tyre dealer.
<
Tyre pressures for trailer towing
For trailer towing, the tyre pressures specified for higher load apply.
Tyre size
The tyre pressures apply to makes of tyre recommended and tyre sizes approved by the manufacturer of your MINI; details are available from MINI Service.
The tyre pressures for approved tyre sizes are shown on the driver's door post.
If your tyres' speed letter is not listed among the pressure data, the tyre pressure for the relevant size applies, e.g. 205/45 R 17.
For Australia/New Zealand
Inflation pressures are specified on the tyre label affixed to the driver's door post.
The inflation pressures on the tyre label are applicable only for tyres explicitly mentioned on the label. Since inflation pressures
Condition of tyres
Inspect tyres regularly for damage, the presence of foreign bodies, unusual wear and sufficient tread depth.
Tread depth
Summer tyres
The tread depth should not be allowed to drop below 3 mm, approx. 1/8 in. Below a tread depth of 3 mm, approx. 1/8 in, there is an increased risk of aquaplaning when driving on wet roads at fairly high speeds.
Winter tyres
Below a tread depth of 4 mm, approx. 3/16 in, winter tyres become noticeably less suitable for winter driving conditions. New tyres should be fitted in the interests of safety.
142
Minimum tread depth
Wheels and tyres
MOBILITY
6 years, regardless of the actual wear of the tyres.
Run-flat tyres*
Wear indicators in the base of the tread groove are distributed around the tyre's circumference; the letters TWI – Tread Wear Indicator – on the tyre's flanks identify tyres that incorporate these wear indicators. Once the tyre tread has worn down to the wear indicators, a tread depth of
1.6 mm, approx. 1/16 in, has been reached.
Tyre damage
Unusual vibrations while the car is being driven could indicate a tyre fault or some other defect on your car. This may have been caused e.g. by driving over a kerb or similar. The same applies to unusual driving characteristics such as violent drag to the left or right.
In such cases, reduce speed immediately and have the wheels and tyres checked without delay. Drive carefully to the nearest
MINI Service Centre or tyre-fitting specialist employing trained personnel and working to the specifications issued by the manufacturer of your MINI. Have the car towed there if necessary.
Otherwise tyre damage could result in accidents with potentially fatal consequences for the vehicle's occupants and other road users.
<
Age of tyres
A tyre's date of manufacture is included in the inscription on the tyre:
DOT...0211 means that the tyre was manufactured in week 2 of 2011.
For various reasons, such as the development of brittleness, the manufacturer of your MINI recommends tyre replacement after no more than
The symbol identifying run-flat tyres is the circle with the letters RSC on the sidewall.
Run-flat tyres comprise a conditionally self-supporting tyre and a special rim. The reinforcement in the side walls ensures that the tyre can continue to be used subject to certain restrictions, even if depressurised.
For information on continuing to drive with a flat
tyre, see Indication of a flat tyre, page 73
.
New wheels and tyres
Have new wheels and tyres installed only by MINI Service or a tyre-fitting specialist employing trained personnel and working to the specifications issued by the manufacturer of your MINI. If such work is performed inexpertly, it could result in consequential damage and thus constitute a safety risk. Make sure that the new wheels are balanced.
<
Retreaded tyres
The manufacturer of your MINI advises against the use of retreaded tyres, otherwise road safety could be impaired. Their carcasses may differ in internal construction or have aged sufficiently to limit their durability.
<
143
MOBILITY Wheels and tyres
Correct wheels and tyres
The manufacturer of your MINI recommends fitting only wheels and tyres that it has approved for your type of vehicle, otherwise the tyres may, e.g., make contact with the vehicle body due to impermissible tolerances, even though they are nominally of the correct size; this could result in a serious accident. The manufacturer of your MINI is unable to assess the suitability of tyres and wheels it has not approved, and therefore cannot guarantee their safety.
<
Ask your MINI Service Centre for details of the correct wheel and tyre combination.
The correct wheel/tyre combination also has an influence on various systems, which could otherwise malfunction, for instance ABS and DSC.
To maintain the vehicle's good road behaviour, always fit tyres of the same make and tread pattern to all wheels. After a tyre has been damaged, fit the original wheel and tyre combination again as soon as possible.
Recommended makes of tyre
Certain makes of tyre are recommended by the manufacturer of your MINI depending on tyre size. They are marked with a clearly visible designation on the sidewall of the tyre.
When properly used, these tyres meet the highest standards in terms of safety and handling characteristics.
Run-flat tyres*
When fitting new tyres or changing over from summer to winter tyres and vice versa, fit runflat tyres for your own safety. In the event of a flat, no compact spare wheel is available. Your
MINI Service Centre will gladly provide details.
Special characteristics of winter tyres
The manufacturer of your MINI recommends winter tyres when driving in winter conditions or at temperatures below +7 6/457. Although all-season tyres with an M+S marking have better winter characteristics than summer tyres, they do not normally match the performance of winter tyres.
Noting speed limit for tyres
Always comply with the speed limit for the winter tyres fitted to your vehicle; failure to do so could result in tyre damage and accidents.
<
If the car is capable of speeds higher than that permitted for the winter tyres, a label stating the maximum permitted speed for the tyres fitted must be displayed in your field of view. Specialist tyre dealers and MINI Service can supply these labels.
Tyre storage
Store wheels and tyres in a cool, dry and preferably dark place when not in use. Protect tyres against contamination from oil, grease and fuel.
Swapping wheels between the axles
Depending on the individual operating conditions, different wear patterns will occur on the front and the rear axles.
The wheels may be changed between the axles to achieve an equal wear pattern. Your MINI
Service Centre will gladly provide details.
After changing, check the inflation pressure and correct if necessary.
144
Wheels and tyres
Snow chains*
Only certain fine-link snow chains have been tested, found safe for use in traffic, and recommended by the manufacturer of your MINI.
Details are available from your MINI Service Centre.
Fit snow chains in pairs and only to front wheels with tyres of the following sizes:
> 195/60 R 16 M+S
When fitting, comply with the snow chain manufacturer's instructions. When snow chains are in use, do not exceed 50 km/h, approx. 30 mph.
Do not initialise the Run Flat Indicator if snow chains are fitted, as the instrument might issue an incorrect reading. When driving with snow chains, it may be helpful to briefly deactivate DSC or activate DTC, see page
<
MOBILITY
145
MOBILITY In the engine compartment
In the engine compartment
Do not work on the car unless you possess the necessary technical knowledge. If unfamiliar with the regulations which have to be complied with, have the work carried out by
MINI Service, or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI. If such work is performed inexpertly, it could result in consequential damage and thus constitute a safety risk.
<
Opening
Engine compartment lid
Releasing
To avoid damage, make sure that the wiper arms are against the windscreen before you open the engine compartment lid.
<
Press the release lever and open the lid.
Closing
Pull the lever.
Do not clean the windscreen or headlights while the engine compartment lid is unlocked. Otherwise the headlight cleaning system * could be damaged.
<
Close the engine compartment lid from a height of about 40 cm, approx. 16 in, with some momentum. It must be clearly heard to engage.
If you notice during the journey that the engine compartment lid has not been closed properly, stop the car as soon as possible and close the lid correctly.
To avoid injuries, ensure that the closing area of the engine compartment lid is unobstructed.
<
146
In the engine compartment
MOBILITY
Important accessories in the engine compartment
Petrol engine
1 Vehicle Identification Number
2 Battery, under the cover 168
4 Engine oil filler cap
5 Coolant expansion tank
6 Fuse box in the engine compartment 166
7 Washer fluid reservoir for headlight and win-
147
MOBILITY
Diesel engine
In the engine compartment
1 Vehicle Identification Number
2 Battery, under the cover 168
4 Engine oil dipstick
5 Coolant expansion tank
6 Fuse box in the engine compartment
7 Washer fluid reservoir for headlight and window washer system
Engine oil
Engine oil consumption depends on driving style and the operating conditions.
Check the engine oil level regularly, for example when refuelling.
Checking the engine oil level
1.
Park the vehicle on a level surface with the engine at operating temperature, i.e. after driving continuously for at least 10 km, approx. 6 miles.
2.
Switch off the engine.
3.
After about 5 minutes pull out the dipstick and wipe it dry with a non-linting cloth, paper towel or similar.
4.
Carefully push the dipstick fully into its tube, then pull it out again.
The oil level must be between the two marks on the dipstick.
The oil quantity corresponding to the distance between the two markings on the dipstick is approx. 1 litre, approx. 2 pints, for the petrol
148
In the engine compartment
MOBILITY engine, and approx. 1.2 litres, approx. 2.6 pints, for the diesel engine.
Do not add oil beyond the upper dipstick mark. Adding too much oil will harm the engine.
<
Adding engine oil
Approved oil grades
Petrol engine
BMW Longlife-01
BMW Longlife-01 FE
BMW Longlife-04
Diesel engine
BMW Longlife-04
Only add oil, and not more than 1 litre, approx.
1.8 pints, when the oil level has fallen to just above the lower mark on the dipstick, page
.
Top up the oil level within the next 50 km or 30 miles, otherwise the engine may suffer damage.
<
If the oil level has been topped up too much, have the vehicle checked immediately, as otherwise engine damage can be caused.
<
Keep oils and greases, etc. out of the reach of children and comply with the warnings on the containers. Otherwise, these products may pose health risks.
<
Oil grades for topping up
Notes
Do not use oil additives, otherwise the engine could be damaged.
<
When selecting an engine oil it should be ensured that it belongs to one of the SAE viscosity classes 0W-40, 0W-30, 5W-40 and 5W-
30, as otherwise functional disorders or engine damage can result.
<
Engine oil quality is a decisive factor for your engine's service life.
Some oil grades are not available in all countries.
Further information on approved oil grades can be obtained from Service.
Alternative oil grades
If approved oils are not available, quantities of up to 1 litre, approx. 1.8 pints, of a different oil with the following specifications may be used:
Petrol engine
BMW Longlife-98
ACEA A3/B4
Diesel engine
ACEA C3
Oil change
Only have oil service performed by Service.
Coolant
Coolant consists of equal quantities of water and coolant additive. Not all common commercial additives are suitable for your MINI. Your MINI
149
MOBILITY In the engine compartment
Service Centre can provide details of which additives are suitable.
Use only suitable additives, otherwise the engine could incur damage. As these additives are hazardous to health, observe the notes on the containers.
<
When disposing of coolant additives, comply with the relevant environmental protection regulations.
<
Coolant temperature
If the coolant and hence the engine overheats, a warning light lights up, see page
Checking coolant level
Do not open up the cooling system while the engine is hot, otherwise you may scald yourself on the escaping coolant steam.
<
Do not open the engine compartment lid until the engine has cooled down.
The coolant level is correct if it is between the
Min. and Max. marks.
Topping up
1.
Turn the cap on the expansion tank slightly anticlockwise until it starts to open, then allow the pressure to escape before opening it fully.
2.
Slowly top up to the correct level but do not overfill.
3.
Turn the cap.
Have the cause of coolant loss rectified as soon as possible.
150
Maintenance
MOBILITY
Maintenance
MINI Maintenance System
The MINI Maintenance System contributes towards upholding the roadworthiness and operating reliability of your MINI. Its purpose is to optimise maintenance measures with a view to minimising the cost of looking after your vehicle.
If and when you come to sell your MINI, a comprehensive record of servicing will prove a significant benefit.
Condition Based Service CBS
Sensors and advanced algorithms take account of the varying conditions in which your MINI is used. Condition Based Service uses these to determine current and future servicing requirements. The system provides you with an opportunity to tailor the scope of maintenance work to your personal standards, so that your MINI will always be reliably operational.
In the revolution counter, you can have the remaining distances and times for selected maintenance tasks as well as any legally prescribed dates displayed to you individually, page
Service data in the remote control
Your vehicle continuously stores information relating to service requirements in the remote control as the vehicle is being driven. Your MINI
Service Advisor can read out this data from the remote control unit and propose an optimised maintenance approach. Whenever you take your car in for servicing you should therefore hand your MINI Service Advisor the remote control unit that you last used.
Make sure that the date in the revolution counter is always set correctly, page
otherwise the effectiveness of Condition Based
Service CBS is not assured.
<
Service
You will find further information on necessary maintenance work and the scope of mainte-
The manufacturer of your MINI recommends having maintenance and repair work carried out by your MINI Service Centre.
Make sure that maintenance work is confirmed after it has been carried out. These entries are evidence that your MINI has been serviced regularly and correctly.
<
For Australia/New Zealand
Maintenance
Your MINI needs only routine maintenance in order to maintain its exhaust emissions to the level specified.
151
MOBILITY Maintenance
Socket for on-board diagnosis OBD
Data memory
Your vehicle saves data about operation, faults and user settings. This data is saved in the vehicle and partly also in the remote control. The information can be read out with suitable devices, especially at the Service centre. The information read out in this way is used to support service processes and repair or for optimising and developing vehicle functions.
Components that are crucial for the composition of emissions can be checked with a device using the OBD socket.
Emissions
The warning lights come on. Vehicle emissions are higher than normal. You can continue your journey, but moderate your speed and exercise due caution. Have the vehicle checked as soon as possible.
Recycling
The very design of your vehicle incorporates a recycling-friendly concept that extends to both the production methods used and the choice of materials.
The manufacturer of your MINI recommends returning your vehicle at the end of its service life to a recycling point specified by the manufacturer of your MINI. In doing this, you will be making an active contribution towards protecting resources and the environment. The regulations concerning the returning of end-oflife vehicles may vary from country to country.
You can obtain more information about this in the Internet under www.MINI.com or from your
MINI Service Centre.
152
General care
MOBILITY
General care
Care products
Regular cleaning and care make an appreciable contribution to the value maintenance of your
MINI.
The manufacturer of your MINI recommends using parts and accessory products for cleaning the car, which the manufacturer of your MINI has approved for this purpose.
MINI Service will be glad to advise you on products and services for the cleaning and care of your MINI.
Original MINI Care Products are subjected to material testing, laboratory testing and practical tests and offer the best care and protection for your vehicle.
<
Do not use alcohol-based or solventbased cleaning agents, as these could cause damage.
<
Cleaning agents can contain hazardous substances or constitute a health risk.
Comply with the warning and hazard avoidance instructions on the respective container. When cleaning the interior of the vehicle, leave doors or windows open.
Never use substances not specifically intended for cleaning the vehicle.
<
Exterior care
Washing the vehicle
During the winter months in particular, wash the vehicle more frequently. Substantial deposits of dirt and road salt can cause damage to the vehicle.
<
After washing the vehicle, drive it briefly and apply the brakes to dry them out; this is necessary to prevent reduced braking effect, and also to avoid corrosion of the brake discs.
<
Vehicle washes
Textile vehicle washes are preferable.
Do not use high pressure car washes, as otherwise drops of water can penetrate at the area around the windows.
<
Before entering the car wash, check whether the system is suitable for your MINI. Take account of the following aspects:
> Vehicle dimensions, page
>
If necessary: fold in exterior mirror, page 37
> Maximum allowable tyre width
Avoid car washes with guide rails higher than 10 cm, approx. 4 in, otherwise they could damage the chassis and suspension.
<
Preparations before driving into the vehicle wash:
> Unscrew the rod antenna.
> Deactivate rain sensor * , to avoid unintended wiping.
> Deactivate the rear window wiper and protect it against damage. If necessary, please ask the operator of the vehicle wash about appropriate protective measures.
> Remove any add-on parts such as spoilers and telephone antennae that could be damaged.
> Insert the remote control in the ignition lock.
Automatic transmission
Before entering the car wash, so that the vehicle can roll:
1.
Inserting the remote control in the ignition lock, even if the vehicle has comfort access.
2.
Move the selector lever to position N.
3.
Release handbrake.
4.
Switching off the engine.
5.
Leaving the remote control in the ignition lock so that the vehicle can roll.
153
MOBILITY General care
Steam jets/high pressure cleaning jets
If you use steam jet cleaners or high-pressure cleaners, make sure you maintain an adequate distance and a temperature of 60 6/
140 7 at maximum.
Too short a distance, too high pressure or too high temperature can damage certain parts of the vehicle or water could enter. Observe the operating instructions for the high pressure cleaning jet.
<
Spray by using high pressure cleaner, not halting long at a point and maintaining a distance of at least 30 cm, approx. 12 in, to sensors, such as e.g. Park Distance Control.
<
Washing by hand
When washing the vehicle by hand, use plenty of water to which vehicle shampoo may be added.
Clean the vehicle with a sponge or washing brush, applying only little pressure.
Before cleaning the windscreen, deactivate the rain sensor or switch off the ignition to prevent unintentional operation of the wipers.
<
Comply with local legislation on the washing of vehicles by hand.
<
Headlights
Do not rub them when dry or use caustic or abrasive cleaning agents. Soak dirt or other deposits, e.g. dead insects, with shampoo and wash down with plenty of water.
Thaw out ice deposits using de-icer; do not use a scraper.
Windows
Clean the outside and inside surfaces of windows and the surfaces of mirrors with glass cleaner.
Do not use quartz-based cleaning agents to clean mirrors.
<
Wiper blades
Clean with soap and water and change regularly to avoid the formation of streaks.
Wax and preservative residues and dirt contamination on the window glass cause the formation of streaks during wiper operation and cause premature wear on the wiper blades and malfunctioning in the rain sensor.
<
Care of paintwork
Regular care helps preserve the value of the vehicle and protects the paintwork against longterm effects by substances that may damage the paintwork.
Environmental factors that vary from region to region could have adverse effects on the vehicle's paintwork and damage it. It is therefore important to adapt the frequency and scope of vehicle care procedures accordingly.
Remove particularly aggressive substances such as spilled fuel, oil, grease, brake fluid, tree sap and bird droppings without delay, otherwise the paintwork could be damaged.
Rectifying paintwork damage
Repair stone damage or scratches immediately, depending on their severity, to prevent rust from forming.
<
The manufacturer of your MINI recommends having paintwork damages repaired by an expert, according to the factory specifications with original MINI paint material.
Protecting the paintwork
Protective treatment is required if water no longer forms large droplets and runs off the clean paintwork surface. When applying protective paintwork treatment, use only products containing carnauba or synthetic waxes.
Rubber seals
Treat only with water or with rubber care products.
154
General care
MOBILITY
Do no apply silicone sprays or other products containing silicone to rubber seals, as otherwise noise and damage could result.
<
Chrome parts*
Carefully clean parts such as the radiator grille or door handles with plenty of water and shampoo additive, especially whenever the car is exposed to the effects of road salt. Use chrome polish by way of additional treatment.
Light-metal alloy wheels*
It is normal for the brakes to generate dust, which then forms deposits on the alloy wheels.
Remove this dust at regular intervals with an acid-free rim cleaner.
Do not use any aggressive, acidic, highly alkaline or raw cleaning agents or steamjet cleaners over 60 6/1407, as otherwise they could cause damage.
<
Exterior sensors
Keep the sensors on the vehicle exterior e.g. Park Distance Control, clean and free from ice, to ensure full functioning.
<
Trailer tow hitch with detachable ball head*
Keep the ball head and the mounting on the vehicle clean. Grease or oil the bearings, sliding surfaces and balls with resin-free grease or oil.
When cleaning with a steam cleaner or high pressure cleaner, the ball head must be removed and the sealing stopper inserted. Do not clean the ball head with a steam cleaner or high pressure cleaner.
General care interior
Upholstery fabrics/fabric trims
Clean regularly with a vacuum cleaner to remove surface dirt.
For more intensive cleaning, e.g. to remove drinks stains, use a soft sponge or a non-linting microfibre cloth in conjunction with a suitable interior cleaner. Observe the instructions on the pack.
Clean upholstery fabrics across a large area, right up to the seams. Avoid rubbing them excessively.
<
Open bur fasteners on trousers or other garments could damage the seat upholstery. Ensure that bur fasteners are fastened.
<
Leather/Leather panelling*
The leather processed by the manufacturer of your MINI is a high-quality natural product. Slight variations in the grain pattern are one of the typical characteristics of authentic leather.
<
Dust and road dirt works its way into the pores and folds, promoting abrasion and causing the leather surface to become prematurely brittle.
You should therefore remove dust from the leather at regular intervals with a cloth or vacuum cleaner.
Especially in case of a light coloured leather, see that it is de-dusted regularly as it tends to collect heavier contamination.
Treat the leather with a leather lotion twice a year, as dirt and grease will attack the leather's protective layer.
Carpets/floor mats*
Make sure that pedal functions are not impaired during travel by floor mats, carpets or other objects.
Do not place additional floor mats on top of existing floor mats or other objects.
Only use floor mats which have been approved for use with the vehicle and can be securely fastened in place.
If you remove floor mats, for cleaning for example, make sure that you fasten them securely back in place.
<
Floor mats can be removed for cleaning.
155
MOBILITY General care
If floor carpets are more heavily soiled, use a microfibre cloth and water or a textile cleaning agent to clean them. In doing so, rub back and forth in the direction of travel, as otherwise the carpet can become tangled.
Interior plastic parts
These include:
> Imitation leather surface finishes
> Lamp lenses
> Display covers
> Matt parts
Clean with water and some solvent-free plastic cleaner.
Do not use any solvents such as alcohol, lacquer thinners, heavy-duty grease removers, gasoline or similar; otherwise the surfaces could be damaged.
<
Decorative strips*
Clean decorative strips exclusively with a moist cloth. Then rub dry with a soft cloth.
Seat belts
Dirt on the seat belts will prevent them from being retracted properly and will therefore impair safety.
Do not dry clean the seat belts, otherwise the fabric may be destroyed.
<
Displays
For the cleaning of displays, such as radio or display elements, a cleaning cloth or a soft, nonscratching, lint-free cloth.
Avoid applying excessive pressure when cleaning displays, otherwise they could be damaged.
<
Do not use any chemical or abrasive domestic cleaning agents. Keep all liquids and any moisture away from the set. Surfaces or electrical components might otherwise be corroded or damaged.
<
CD/DVD drives
Do not use cleaning CDs, as these could damage drive components.
<
Placing the vehicle in storage
If you plan not to use your vehicle for longer than three months, please consult your MINI
Service Centre or a workshop which works according to the MINI manufacturer's specifications.
156
Replacing parts
MOBILITY
Replacing parts
Wiper blades
Changing front wiper blades
1.
Swing the wiper arm clear and hold it in this position.
3.
Press the wiper blade against the stop until it disengages.
4.
Press the new wiper blade into the mounting until it audibly engages.
2.
Squeeze the latching spring, arrows 1, and swing the wiper blade out, arrow 2.
3.
Pull the wiper blade towards you and out of the catch.
4.
Press the new wiper blade into the mounting until it audibly engages.
In order to avoid damage, make sure that the wiper arms are against the windscreen before you open the engine compartment.
<
Changing rear wiper blade
1.
Swing the wiper arm clear and hold it in this position.
2.
Turn the wiper blade all the way towards the rear, arrow.
Lights and bulbs
Lights and bulbs are an important aspect of driving safety. They should, therefore, be handled carefully. The manufacturer of your MINI recommends that any bulb-related routines that you are not familiar with or that are not described here be entrusted to your MINI Service Centre.
Do not touch the glass of a new bulb with the fingers, because even slight amounts of dirt or grease will then be burned into the bulb and reduce its working life. Use a clean tissue, cloth or similar, or hold the bulb by its base.
<
A box containing spare bulbs is available from your MINI Service Centre.
When working on electrical systems, always begin by switching off the consumer in question, as otherwise short-circuits could result. Observe any instructions supplied by the bulb manufacturer, to avoid the risk of injury or damage when changing bulbs.
<
For information on headlight care, see
For bulb changes that are not described, consult MINI Service or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI.
<
Light-emitting diodes LEDs
Controls, displays and other equipment items inside your vehicle have light-emitting diodes behind a cover as their light source. These LEDs
157
MOBILITY Replacing parts resemble conventional laser diodes and are classified by law as Class 1 light-emitting diodes.
Do not remove the covers or expose the eyes directly to the unfiltered light source for several hours at a time, as this could cause irritation to the retina.
<
Headlight lenses
Condensation might form on the inside of the headlight lenses in cool or damp weather. When the lights are switched on, the condensation disappears after a short time. There is no need to replace the headlights. In the event of more extensive moisture, for example water droplets in the light, have this checked by Service.
Bi-xenon headlights*
The operating life of these light units is extremely long and the likelihood of failure very low, provided that they are not switched on and off a very great number of times. If a xenon headlight fails nonetheless, switch on the fog lights and continue the journey with great care, provided that local legislation does not prohibit this.
Always have work on the xenon lights, including bulb changes, carried out by
MINI Service or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI. In view of the high electrical voltages present, there is a risk of potentially fatal accidents if work is performed inexpertly.
<
Halogen low-beam and high-beam headlights
H4 bulb, 60/55 watts
The H4 bulb is pressurised, so wear goggles and gloves. There is otherwise a risk of injury if the bulb is damaged.
<
Take care when installing the cover, as otherwise leaks could occur and cause damage to the headlight system.
<
Access to the bulb in the engine compartment
The bulb for the low-beam/high-beam headlight can be changed from the engine compartment.
To remove the cover:
1.
Press the tab.
2.
Flip the cover upwards and take it out of the holder.
Follow the same steps in reverse order to refit the cover.
Take care when installing the cover, as otherwise leaks could occur and cause damage to the headlight system.
<
Changing bulbs
1.
Press the retaining clip forwards and hold it there, arrow 1.
2.
Guide the retaining clip downwards, arrow 2.
158
Replacing parts
MOBILITY
3.
Fold the retaining clip to the side, arrow 3.
3.
Remove inner cover.
To do so, turn the cover anticlockwise.
4.
Remove the bulb.
5.
Install new bulb with the tab pointing upwards, arrow 4.
6.
Fold back the retaining clip and lock it.
7.
Reattach the cover.
Turn signal indicators, side lights/ parking lights and fog lights
Access to bulbs from wheel well
4.
Turn the bulb anticlockwise and take it out.
1 Flashing turn indicators
2 Side light/parking light/fog light
Changing flashing turn indicator bulb
21 watt bulb, P21W or PY 21 W if applicable
1.
Turn the wheel.
2.
Remove cover 1.
To do so, turn the cover anticlockwise.
5.
To install the new bulb and reattach the covers, take the above steps in reverse order.
Changing side light/parking light bulb
5 watt bulb, W 5 W
1.
Turn the wheel.
2.
Remove cover 2.
To do so, turn the cover anticlockwise.
3.
Turn the upper bulb anticlockwise and take it out.
4.
To install the new bulb and reattach the cover, take the above steps in reverse order.
159
MOBILITY Replacing parts
Changing fog light bulb
H8 bulb, 35 watts
1.
Turn the wheel.
2.
Remove cover 2.
To do so, turn the cover anticlockwise.
3.
Attach the cable connector.
4.
Turn the lower bulb anticlockwise and take it out.
Rear lights
Bulb, P 21 W
5.
To install the new bulb and reattach the cover, take the above steps in reverse order.
Side flashing turn indicators
5 watt bulb, W 5 W
1.
Open the engine compartment lid.
1 Brake lights/tail lights
2 Flashing turn indicators
3 Brake lights/tail lights
4 Rear fog light *
5 Reversing lights
Change
All of the bulbs are mounted in a central bulb holder.
1.
Switch off the lights and take the remote control out of the ignition lock.
2.
Press out the cover on the luggage compartment side trim panel and remove.
2.
Squeeze the clamping clip, arrows, and remove the bulb holder.
3.
Unscrew and remove the bulb and change it.
4.
To install the new bulb and reattach the cover, take the above steps in reverse order.
160
Replacing parts
MOBILITY
3.
Release the bulb holder by pressing down on the clamping clip, arrow.
4.
Take out the bulb holder.
5.
Press the bulb in slightly and turn to the left, take out and change.
6.
Re-engage the bulb holder so that it audibly clicks into place.
7.
Reattach the cover.
Licence plate light
5 watt bulb, C 5 W
1.
Using a screwdriver, push the light to the left in the flap of the light housing, arrow 1.
2.
Take out the light, arrow 2.
3.
Change the bulb.
4.
Insert the light.
Centre brake light
This light uses LED technology. In the event of a defect, consult a MINI Service Centre or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your MINI.
Repairing a flat tyre
Safety precautions in the event of a puncture:
Halt the vehicle as far away from the main traffic flow as possible, switch on the hazard warning flashers.
Engage the steering lock in the straight-ahead position, apply the handbrake and select first or reverse gear or selector lever position P.
All occupants must leave the vehicle and be led to a point where they are not exposed to risk, for example behind a crash barrier at the side of the road.
If necessary, set up the warning triangle or a flashing warning light at a sufficient distance to the rear. Comply with national legislation.
<
In the event of a puncture, the proper procedure depends on your vehicle's equipment:
> MINI Mobility System, see the following section
> Run-flat tyres, page
MINI Mobility System*
The Mobility System is located underneath the left-hand front seat.
Preparations
Use of the Mobility System may be ineffective if the tyre puncture measures approx. 4 mm, approx. 1/8 in, or more. Contact the nearest
MINI Service Centre if the tyre cannot be repaired with the Mobility System so that it is possible to continue driving.
If possible, leave foreign bodies that have penetrated the tyre in the tyre.
Observe instructions for using the Mobility
System on the compressor and sealant bottle.
<
Remove speed limit sticker from the sealant cylinder and attach to the steering wheel.
161
MOBILITY Replacing parts
Sealant and compressor
1 Sealant cylinder with speed limit sticker
2 Filler hose
Please observe the best before date on the sealant cylinder.
<
> Spreading the sealant
> Correcting the tyre inflation pressure
Filling the sealant
Please keep to the following sequence to avoid the sealant escaping with high pressure.
<
1.
Shake the sealant cylinder.
2.
Completely remove the connecting hose 6 from the compressor housing and screw onto the connector of the sealant cylinder.
Make sure the connecting hose is not kinked.
3.
Insert the sealant cylinder into the housing of the compressor so that it is in upright position.
3 Bracket for the sealant cylinder
4 Compressor
5 Adapter and cable for the socket on the inside of the vehicle, page
6 Connecting hose for connecting the compressor and the sealant cylinder or the compressor and the wheel
7 Switching on/off
8 Pressure gauge to display the tyre inflation pressure
9 Deflation button to reduce the tyre pressure
Plug connector, cable and connecting hose are located in the compressor housing.
Using the Mobility System
Please proceed as follows to remedy a flat tyre with the Mobility System:
> Filling the sealant
4.
Unscrew the dust cap from the valve of the faulty wheel and screw the filler tube 2 of the sealant cylinder onto the valve.
5.
Make sure the compressor is turned off.
6.
Insert the plug 5 into the cigarette lighter socket/socket on the inside of the vehicle,
.
7.
When the engine is running:
Switch on the compressor and let it run for approx. 3 to 8 minutes to fill the sealant and reach a tyre inflation pressure of approx.
1.8 bar/26.1 psi.
When filling the sealant, the inflation pressure can briefly rise to approx.
5 bar, approx. 72.5 psi. Do not switch off the compressor at this stage.
<
162
Replacing parts
MOBILITY
Do not let the compressor run for more than 10 minutes. Otherwise the device will overheat and could be damaged.
<
8.
Switch off the compressor.
If a pressure of 1.8 bar/26.1 psi is not achieved:
1.
Remove the filling hose 2 from the wheel and drive forwards and backwards for approx. 10 m, approx. 32 ft, to allow the sealant to spread inside the tyre.
2.
Inflate the tyre with the compressor again.
If a tyre pressure of 1.8 bar/26.1 psi still cannot be achieved, the tyre damage is too severe. Contact your nearest MINI Service
Centre.
<
Stowing the Mobility System
1.
Unscrew the filling hose 2 for the sealant cylinder from the wheel.
2.
Unscrew the compressor's connecting hose 6 from the sealant cylinder.
3.
Connect the filling hose 2 for the sealant cylinder to the free connection on the sealant cylinder.
This stops the rest of the sealant escaping from the bottle.
4.
Pack the empty sealant cylinder to avoid soiling in the luggage compartment.
5.
Secure the Mobility System in the vehicle.
Spreading the sealant
Immediately drive for approx. 5 km, approx.
3 miles, so that the sealant can spread evenly.
Do not exceed a speed of 80 km/h, approx. 50 mph.
If possible, maintain a speed of at least 20 km/h, approx. 12 mph.
<
Correcting the tyre inflation pressure
1.
Stop in a suitable location after a distance of approx. 5 km, approx. 3.5 miles, or
10 minutes.
2.
Screw the connecting hose 6 of the compressor directly onto the tyre valve.
3.
Insert the plug 5 into the socket on the inside of the vehicle.
4.
Correct the tyre inflation pressure to 1.8 bar/
26.1 psi. For this purpose, carry out the following while the engine is running:
> Increase the tyre inflation pressure: switch on the compressor. Switch of the compressor to check the currently set tyre inflation pressure.
Do not let the compressor run for more than 10 minutes. Otherwise the device will overheat and could be damaged.
<
> Reducing tyre inflation pressure: press the deflation button 9.
If the tyre inflation pressure is not maintained, drive the vehicle again, see
Spreading the sealant. Subsequently repeat steps 1 to 4.
If a tyre pressure of 1.8 bar/26.1 psi still cannot be achieved, the tyre damage is too severe. Contact the nearest MINI Service Centre.
<
Resuming the journey
Do not exceed the maximum speed of
80 km/h, approx. 50 mph, to avoid the risk of accidents.
<
Have the defective tyre replaced as soon as possible, and the wheel and tyre rebalanced.
Have the Mobility System refilled.
Changing a wheel
The bag containing the kit for changing a wheel * is stored underneath the flat luggage compartment floor * . The kit contains:
163
MOBILITY Replacing parts
> Jack
> Ratchet
> Wheel brace
> Puller for central wheel cover
> Chock
For Australia/New Zealand: vehicle jack*
The Australian/New Zealand Standard AS/
NZS 2693:
2003 - 'Vehicle Jacks' includes the following warning which the manufacturer of your MINI herewith adopts:
'No person should place any portion of their body under a vehicle that is supported only by a jack; use vehicle support stands.'
For your own safety, the manufacturer of your
MINI strongly recommend that you should never place any portion of your body under your car at any time, for any reason.
The jack supplied with your car should not be used for any purpose other than wheel changing and should never be used in conjunction with a vehicle support stand. Raising the vehicle for the purpose of inspection should only be performed in a controlled workshop environment on a hoist by trained personnel.
The following AS/NZS 2693: 2003 warnings are repeated here:
The jack should be used on level firm ground wherever possible. It is recommended that the wheels of the vehicle be chocked, and that no person should remain in a vehicle that is being jacked.
<
The jack of your MINI is maintenance-free.
Please observe the information marked on the jack.
<
Preparing to change the wheel
Observe the safety notes on repairing a flat tyre on page
<
Additional safety precautions when changing a wheel:
Only change wheels on a flat, firm and non-slip surface.
On a soft or low-grip surface, snow, ice, tiles or similar, there is a risk of the vehicle or the jack sliding sideways.
Never place wood blocks or similar under the jack, or the maximum support capacity may not be reached due to the restricted height.
When the vehicle is jacked up, do not lie under it or start the engine, as this could lead to a potentially fatal accident.
<
If your vehicle is towing a trailer, remove it.
1.
Place the hinged wheel chock * behind the front wheel on the side opposite to where the wheel is to be removed, or in front of the front wheel on a downhill gradient. If the vehicle is on a severe gradient, protect it reliably against rolling away.
2.
If necessary, uncover the wheel studs.
> For central wheel cover *
Remove the cover.
> For light-metal alloy wheels *
See Thief-proof wheel studs on page
3.
Slacken off the wheel studs by half a turn.
Jacking up the vehicle
Use the jack only for wheel-changing. Do not attempt to raise another type of vehicle or any other load with this jack; this could result in injury or damage.
<
1.
Position the jack under the support point nearest the wheel.
The entire base of the jack must be lying flat on the ground beneath the support point.
164
Replacing parts
MOBILITY
2.
Fix ratchet to the mounting on the support point, arrow 1.
Have the flat tyre replaced as soon as possible, and the wheel and tyre rebalanced before fitting.
Theftproof wheel studs*
3.
While cranking up, attach jack head to the mounting point on the bodywork, arrow 2.
4.
Continue to turn the crank handle until the wheel you wish to change is lifted clear of the ground.
Fitting a wheel
1.
Unscrew the wheel studs and remove the wheel.
2.
Remove heavy dirt deposits from the wheel and hub contact faces and clean the wheel studs.
3.
Mount the new wheel.
4.
Screw in at least two wheel studs on opposite sides of the hub.
5.
Screw in the remaining wheel studs.
6.
Tighten all wheel studs well in diagonally opposed pairs.
7.
Lower the vehicle.
8.
Remove the jack.
Tightening the wheel studs
Tighten the wheel studs again in diagonally opposed pairs.
Without delay, have the wheel stud tightening torque checked using a calibrated torque wrench. Incorrectly tightened wheel studs otherwise represent a safety risk.
<
Tightening torque: 140 Nm, approx. 103 lb ft.
1 Wheel stud for adapter
2 Adapter
Removing
The adapter is located behind the right-hand cover in the luggage compartment side panel.
1.
Remove the cover, arrow.
2.
Take the adapter 2 out of the toolkit and place it on the wheel stud.
3.
Unscrew wheel stud 1.
After inserting, remove the adapter again.
If you lose the adapter, contact your MINI
Service Centre.
<
165
MOBILITY Replacing parts
Vehicle battery
Maintenance
The battery needs no routine maintenance whatsoever, in other words the quantity of acid it contains will normally last for the full operating life of the battery in temperate climates.
Replacing the battery
Only use vehicle battery types that have been approved by your vehicle manufacturer, otherwise damage to the vehicle may occur or systems or functions may not be available, either entirely or partly.
<
After battery replacement, have your battery registered in the vehicle by your Service so all convenient functions are unrestrictedly available.
Recharging the battery
Only charge the battery in the vehicle if the
engine is switched off. Connections, see Jumpstarting on page 168 .
Disposal
Have your MINI Service Centre dispose of old batteries after they are removed, or bring the batteries to an authorised collecting point. Batteries filled with acid should be transported and stored upright. Protect batteries against falling over when in transit.
<
Power failure
After a temporary power failure, the functions of certain equipment items may be restricted and require initialising. Individual settings will likewise be lost, and will need to be reprogrammed:
> Time and date
These values must be updated, page
> Radio
Station must be saved again, see Radio MINI
CD, page 110 or Radio MINI Boost CD,
page
.
> Glass roof * , electric
It is possible that the roof can only be lifted.
The system must be initialised. Contact your
MINI Service Centre.
Fuses
Do not repair blown fuses or replace them with fuses with different colours or ampere ratings, otherwise overloaded electrical wires can cause a fire in the vehicle. Have fuses replaced by MINI Service or a workshop employing trained personnel and working to the specifications issued by the manufacturer of your
MINI.
<
See the inside of the covers for information on fuse assignment.
In the engine compartment
To open the cover
Press the snap-fit catch.
166
In the interior
On the right-hand side of the footwell.
To open the cover
Press out at the recess.
Replacing parts
MOBILITY
167
MOBILITY Mutual aid
Mutual aid
Mobile Service
Mobile Service is available via the telephone around the clock in most countries. This service can render assistance in the event of a breakdown.
First aid pouch*
Certain items in the first aid pouch have a limited useful life. Check the expiry dates of the contents regularly and replace any items that have expired.
The first-aid pouch is located on the luggage compartment floor on the left-hand side trim panel or under the luggage compartment floor.
Warning triangle*
Jump-starting
If the car's own battery is discharged, your
MINI's engine can be started by using two jump leads from another vehicle's battery. In the same way, you can help another vehicle to start.
Use only leads with fully insulated terminal clamps.
Do not touch any electrically live parts when the engine is running, or a fatal accident may occur. Do not depart from the procedure described below, otherwise personal injury could result or one or both vehicles sustain damage.
<
Preparations
1.
Check whether the battery of the other vehicle has a voltage of 12 Volt and approximately the same capacity in Amp/h. This should be printed on the battery.
2.
Switch off the engine of the donor vehicle.
3.
Switch off any consumers in both vehicles.
The bodies of the two vehicles must not make contact, otherwise there is the risk of a short-circuit.
<
Connecting the jump leads
Connect the jump leads in the correct order to avoid sparks that could cause injury.
<
In the luggage area under the load edge.
To remove the triangle, open the two fasteners.
168
Mutual aid
MOBILITY
1.
Open the cover of the battery in the engine compartment to reach the positive terminal of your MINI.
Body earth on the MINI with petrol engine:
2.
Release the left and right tabs on the cover over the positive terminal * , arrow 1, and lift the cover to open it, arrow 2.
Body earth on the MINI with diesel engine:
3.
Connect a terminal clamp on the positive/+ jump lead to the positive battery terminal or a jump-starting connection on the donor vehicle.
4.
Connect the second terminal clamp on the positive/+ jump lead to the positive battery terminal or a jump-starting connection on the vehicle to be started.
5.
Connect a terminal clamp on the negative/– jump lead to the negative battery terminal or the engine or body earth connection on the donor vehicle.
6.
Connect the second terminal clamp on the negative/– jump lead to the negative battery terminal or a ground/earth connection on the engine or body of the vehicle to be started.
Starting the engine
1.
Start the engine of the donor vehicle and allow it to run for a few minutes at a slightly increased idle speed.
2.
Start the engine of the other vehicle in the customary way.
If an initial attempt to start the engine fails, wait several minutes until the flat battery has been recharged to a slightly greater degree.
3.
Allow the engines to run for a few minutes.
4.
Disconnect the jump leads in the opposite order from that in which they were originally attached.
Check the battery if necessary and have it recharged.
169
MOBILITY Mutual aid
Do not use the spray products sold as starting aids.
<
Front
Tow-starting, towing away
In some countries, it is prohibited to tow another vehicle on public roads by means of a towbar or towrope.
Familiarise yourself with the relevant legislation in the country in question.
Using the towing eye
The screw-in towing eye must always be carried on the vehicle. It can be screwed in at the front or rear right.
The towing eye is stored underneath the front right-hand seat.
Use only the towing eye supplied with the car, and make sure that it is screwed in fully and is tight. Only use the towing eye for towing on roads. Avoid lateral loads on the towing eye, e.g. do not raise the vehicle at the towing eye. Otherwise, the towing eye and the vehicle could sustain damage.
<
Access to screw thread
Press on the lower section of the cover. This pushes out the top edge of the cover so that it can be removed.
Rear
Being towed
If the electrical system fails, do not attempt to tow-start or tow away the car.
The electrical steering-wheel lock cannot be dis-
engaged and the car is not steerable. Jumpstarting, see page 168 .
<
Servo assistance is not available when the engine is not running. The steering and brakes will require extra effort to operate.
Switch on the hazard warning flashers, depending on local regulations.
Manual gearbox
Gearshift lever in idle position.
Automatic transmission
Only transport vehicles with an automatic transmission on a breakdown lorry or with the front wheels raised. Otherwise the transmission may be damaged.
<
170
Mutual aid
MOBILITY
Towing methods
Do not raise the vehicle at the towing eye or by body or suspension components, otherwise it could sustain damage.
<
With towbar
The towing vehicle must not be lighter than the towed vehicle, otherwise it may be impossible to maintain control.
<
The towing eyes of both vehicles should be on the same side. If it is impossible to avoid attaching the towbar at an angle, note the following:
> Towbar clearance may be restricted when cornering.
> The towbar will generate lateral forces if it is attached offset.
Only attach the towbar to the towing eyes.
Attaching the towbar to other parts of the vehicle can result in damage.
<
With towrope
Ensure that the towrope is taut when the towing vehicle moves off.
For towing, use nylon ropes or tapes, as these will help avoid sudden tensile loads.
Only attach the towrope to the towing eyes.
Attaching the towrope to other parts of the vehicle can result in damage.
<
With tow truck: vehicles without ALL4 four-wheel drive
With tow truck: vehicle with ALL4 fourwheel drive
Do not tow away a vehicle with ALL4 fourwheel drive with just the front or rear axle raised off the ground, otherwise the wheels could lock and the transfer box be damaged.
<
A loading platform must always be used when transporting the MINI Countryman.
Tow-starting
If possible, you should use jump leads instead of tow-starting to start the engine, page
. On cars with catalytic converters, tow-starting should only be used if the engine is cold; on cars with automatic transmission, it is not possible to tow-start the engine.
1.
Switch on the hazard warning flashers, complying with local regulations.
2.
Switch on the ignition, page 46
.
3.
Engage 3rd gear.
4.
Depress the clutch before beginning to be towed. When the car is moving, gradually release the clutch. Press the clutch down fully again as soon as the engine has started.
5.
Halt in a suitable place, remove the towbar or towrope and switch off the hazard warning flashers.
6.
Have the vehicle checked.
Transport the MINI Countryman with tow trucks using a so-called hoisting frame or on a loading platform.
171
MOBILITY Indicator and warning lights
Indicator and warning lights
Please follow the notes about the cause and the action required from the table. Note whether a light comes on alone or in combination with another. Some lights can show in different colours. Corresponding distinctions are drawn in the text.
Indicator and warning lights can come on in various combinations and colours in panels 1 or 2.
1 2 Cause
Flashing turn indicators
High-beam headlights/headlight flasher switched on
Fog lights switched on
Rear fog light switched on
Fasten seat belts
Handbrake applied
Outside temperature warning
What to do
Fastening your seat belt, see also page
Release handbrake.
Drive cautiously, see also page 59
.
172
Indicator and warning lights
MOBILITY
1 2
Lights up briefly:
Cause
Approx. 8 litres, approx. 1.8 gal, of fuel left in the tank
Remains on:
Remaining operating range is no more than 50 km, approx. 30 miles, page
Engine refuses to start
What to do
Ignition switched on and driver's door open
Switch off the ignition, page 46
, or close the driver's door.
Lights still switched on
Depress the brake or clutch preparatory to starting the engine, page
Parking lights switched on
Preheat, see page
Door open
Engine compartment lid open
Window washer fluid level too low Top up the washer fluid as soon as possible, page
173
MOBILITY Indicator and warning lights
1 2 Cause What to do
Shows red:
Service due Arrange an appointment to have the car serviced.
Check service requirements, page
Shows yellow:
The engine will start the next time the start/stop button is pressed, possibly without the brake or clutch being depressed
Remote control faulty, or not detected if car has convenient access
Discharge rechargeable battery or battery of the remote control
Belt tensioners and/or airbag system failed
Power-assisted steering failure
The engine cannot be started. Have the remote control checked, if necessary.
Drive a longer journey using the remote control or, if the car has convenient access, replace the battery.
Have the system checked without delay. Fasten your seat belt in any case.
You can continue your journey, but moderate your speed and exercise due caution. Significantly altered steering characteristics. Have the system checked without delay.
Shows red:
Engine malfunction
Stop the car and switch off the engine. You cannot continue your journey. Consult MINI Service.
Shows yellow:
Full engine power is no longer available
You can continue your journey, but moderate your speed and exercise due caution. Have the engine checked as soon as possible.
174
Indicator and warning lights
MOBILITY
1 2 Cause
If indicator light 1 is flashing:
Engine fault under high load. High engine load will result in damage to the catalytic converter
Shows red:
Engine overheating
What to do
You can continue your journey, but moderate your speed and exercise due caution. Have the vehicle checked without delay.
If indicator light 1 is lit:
Engine malfunction with degradation of the emissions
You can continue your journey, but moderate your speed and exercise due caution. Have the car checked as soon as possible.
Exercising due care, bring the car to a stop, switch off the engine and allow it to cool down. Do not open the engine compartment lid, as there would be a risk of injury by scalding. Consult MINI
Service.
Shows yellow:
Engine too hot Continue driving at more moderate speed so that the engine can cool down. Have the engine checked without delay if the situation reoccurs.
Shows red:
Battery is no longer being charged.
Alternator fault
Switch off all unnecessary electrical consumers. Have the battery checked without delay.
Shows yellow:
Battery charge level very low, battery aged or not securely connected
Have the battery checked as soon as possible.
175
MOBILITY Indicator and warning lights
1 2 Cause
Shows red:
Brake fluid level too low
What to do
Braking effect reduced, stop with caution. Consult MINI Service.
Shows yellow:
Hill Start Assist failure. The vehicle will not be held in place after the brake is released
Brake pads worn
Have the system checked as soon as possible.
Have the condition of the brake pads checked without delay.
Vehicle electronics failed You cannot continue your journey.
Consult MINI Service.
176
Indicator and warning lights
MOBILITY
1 2
Shows red:
Cause
> Starter failed or
> Ignition malfunctioning; engine restart possible only when brake is depressed or
> Lighting system failed; low-beam headlights/rear lights and brake lights still operational; all other lights failed
Shows yellow:
> Control of the brake lights failed or
> Fuel supply faulty
> Drive system malfunctioning
What to do
Have the system in question checked without delay.
The engine cannot be restarted.
Depress the brake to restart the engine.
You can continue your journey, but moderate your speed and exercise due caution. Have the system in question checked without delay.
You can continue your journey, but moderate your speed and exercise due caution. Transmission limp-home programme active with reduced acceleration. Have the system checked without delay.
Flashing:
Dynamic Stability Control DSC or
Dynamic Traction Control DTC controls the drive and braking forces, see also page
Activated Dynamic Traction Control
Dynamic Stability control DSC and
Dynamic Traction Control DTC are deactivated, see also page
Driving stability limited during acceleration and cornering.
Driving style must be adjusted.
177
MOBILITY Indicator and warning lights
1 2 Cause
Dynamic Stability Control DSC and
Dynamic Traction Control DTC failed.
The driving stability control systems, including ABS and the Run Flat Indicator have failed, see also page
What to do
Driving stability limited during acceleration and cornering.
You can continue your journey, but moderate your speed and exercise due caution. Have the system checked as soon as possible.
Hampered braking and driving stability. Drive cautiously and think well ahead. Avoid situations that require full braking. Have the system checked without delay.
The driving stability control systems, including ABS and the Run Flat Indicator have failed, see also page
Hampered braking and driving stability. Drive cautiously and think well ahead. Avoid situations that require full braking. Have the system checked without delay.
ALL4 four-wheel drive failed.
ALL4 four-wheel and DSC drive failed.
You can continue your journey. Drive cautiously and think well ahead. Avoid full throttle and do not use the automatic transmission kick-down. Have the system checked without delay.
You can continue your journey. Drive cautiously and think well ahead. Avoid full throttle and do not use the automatic transmission kick-down. Have the system checked without delay.
178
Indicator and warning lights
MOBILITY
1 2 Cause
Shows red:
> Tyre is deflated
What to do
Carefully bring the car to a stop. Comply with the additional information
.
Initialise Run Flat Indicator, page 72
.
> Run Flat Indicator not initialised
Shows yellow:
Run Flat Indicator failed. Punctures are not indicated
Shows red:
> Transmission limp-home pro-
> gramme active with restricted range of gears, possibly with reduced acceleration
> Gears can be engaged without depressing the brake
Automatic selector lever locked
Shows yellow:
Have the system checked.
You can continue your journey, but moderate your speed and exercise due caution. Have the system checked without delay.
Always depress the brake to engage a gear.
Manually unlock selector lever interlock, page 51 .
Have the system checked as soon as possible.
Manually unlock selector lever interlock, page 51 .
> Automatic selector lever locked:
Selector lever locked in position P with engine running and brake depressed or
> Brake signal faulty: gear can be engaged without depressing the brake
When the vehicle is at a standstill, always depress the brake to engage a gear. Before leaving the vehicle, move the selector lever to position P and switch off the engine.
179
MOBILITY Indicator and warning lights
1 2 Cause
Shows red:
Transmission overheating
What to do
Bring the car to a stop and move the selector lever to position P. Allow the transmission to cool down. You can continue your journey, but moderate your speed and exercise due caution.
Have the system checked if the situation reoccurs.
Shows yellow:
Transmission too hot Avoid high engine loads. You can continue your journey, but moderate your speed and exercise due caution.
Selector lever position P not engaged.
Vehicle not prevented from rolling
Selector lever position P not engaged.
Ignition cannot be switched off
Engage selector lever position P when you wish to switch off the ignition, page
Shows red:
Electric steering-wheel lock faulty The engine can no longer be started. If applicable, do not switch off the engine. Consult MINI Service.
Shows yellow:
Electric steering-wheel lock engaged
Cruise control system failed
Move the steering wheel before starting the engine.
Have the system checked.
Park Distance Control failed Have the system checked.
Bulb of exterior lighting system failed Have the exterior lighting checked as soon as possible.
180
Indicator and warning lights
MOBILITY
1 2 Cause
Low-beam headlight or fog light failed
High-beam headlight failed
Rear fog light failed
What to do
Have the lights checked as soon as possible.
Have the high-beam headlights checked.
Have the rear fog light checked.
Headlight beam throw adjustment system failed
Adaptive Head Light failed
Have the headlight beam throw adjustment system checked.
Coolant level too low
Diesel particle filter malfunctioning
Engine oil pressure too low
Top up coolant immediately, page
.
You can continue your journey. Have the system checked as soon as possible.
Stop immediately and switch off the engine. You cannot continue your journey. Consult MINI Service.
Shows red:
Service appointment overdue Arrange an appointment to have the car serviced.
Check service requirements, page 63
.
Shows yellow:
Service due Arrange an appointment to have the car serviced.
Check service requirements, page 63
.
No service due
181
MOBILITY Indicator and warning lights
1 2 Cause
Set speed limit exceeded
Time and date no longer correct
What to do
Set the time and date, page
Engine has been shut down by the automatic start/stop function
Automatic start/stop function disabled
Automatic start/stop function failure
To start the engine: depress the clutch, see page
Automatic start/stop function disabled using button in the centre console, see page
down or started automatically. To start/stop the engine: press the start/ stop button.
The engine is not shut down or started automatically, see page
start the engine using the start/stop button. Have the system checked as soon as possible.
182
Indicator and warning lights
MOBILITY
183
Find Me.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
OVERVIEW
CONTROLS
DRIVING HINTS
Entertainment
COMMUNICATION
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
REFERENCE Technical data
Technical data
Dimensions
186
All dimensions in mm. Smallest turning circle dia.: 11.6 m, approx. 38 ft.
Technical data
REFERENCE
Weights
One Cooper Cooper S
Kerb weight, ready for road, with 75 kg, approx. 165 lb load, tank 90 Ξ full, without optional extras
> Manual gearbox
> Automatic transmission kg
(lb) kg
(lb)
1340
(2954)
1370
(3020)
1340
(2954)
1370
(3020)
1385
(3053)
1410
(3108)
Permitted gross weight
> Manual gearbox
> Automatic transmission
Front axle load limit
> Manual gearbox kg
(lb) kg
(lb)
1735
(3825)
1765
(3891)
1735
(3825)
1765
(3891)
1780
(3924)
1805
(3979)
> Automatic transmission
Rear axle load limit kg
(lb) kg
(lb)
935
(2061)
965
(2127)
930
(2050)
960
(2116)
960
(2116)
980
(2160)
Roof load
Luggage compartment capacity kg
(lb) kg
(lb) litres
(cu ft)
855
(1885)
75
(165)
350 - 1170
(12.35 - 41.30)
855
(1885)
75
(165)
350 - 1170
(12.35 - 41.30)
855
(1885)
75
(165)
350 - 1170
(12.35 - 41.30)
187
REFERENCE Technical data
One D Cooper D Cooper SD
Kerb weight, ready for road, with 75 kg, approx. 165 lb load, tank 90 Ξ full, without optional extras
> Manual gearbox
> Automatic transmission
Permitted gross weight kg
(lb) kg
(lb)
1385
(3053)
–
1385
(3053)
1410
(3108)
1395
(3075)
1420
(3130)
> Manual gearbox
> Automatic transmission
Front axle load limit
> Manual gearbox kg
(lb) kg
(lb)
1780
(3924)
–
1780
(3924)
1805
(3979)
1790
(3946)
1815
(4001)
> Automatic transmission
Rear axle load limit kg
(lb) kg
(lb) kg
(lb)
995
(2193)
–
985
(2171)
1005
(2216)
850
(1874)
995
(2193)
1015
(2216)
855
(1885)
Roof load
Luggage compartment capacity kg
(lb) litres
(cu ft)
850
(1874)
75
(165)
350 - 1170
(12.35 - 41.30)
75
(165)
350 - 1170
(12.35 - 41.30)
75
(165)
350 - 1170
(12.35 - 41.30)
Cooper S Cooper D Cooper SD All4
Kerb weight, ready for road, with 75 kg, approx. 165 lb load, tank 90 Ξ full, without optional extras
> Manual gearbox kg
(lb)
1455
(3207)
1455
(3207)
1470
(3240)
> Automatic transmission kg
(lb)
1480
(3262)
1480
(3262)
1495
(3296)
188
Technical data
REFERENCE
Cooper S Cooper D Cooper SD All4
Permitted gross weight
> Manual gearbox
> Automatic transmission
Front axle load limit
> Manual gearbox
> Automatic transmission
Rear axle load limit
Roof load
Luggage compartment capacity kg
(lb) kg
(lb) kg
(lb) kg
(lb) kg
(lb) kg
(lb) litres
(cu ft)
1840
(4056)
1865
(4111)
1850
(4078)
1875
(4134)
1855
(4089)
1880
(4144)
980
(2160)
1000
(2204)
895
(1973)
75
(165)
350 - 1170
(12.35 - 41.30)
1010
(2226)
1030
(2270)
890
(1962)
75
(165)
350 - 1170
(12.35 - 41.30)
1015
(2216)
1035
(2281)
900
(1984)
75
(165)
350 - 1170
(12.35 - 41.30)
189
REFERENCE Technical data
Towing a trailer
Cooper Cooper S Cooper D Cooper SD
Towing loads according to EU operating permit. Note and comply with different values in certain countries. Your MINI Service Centre will have details of possible increases.
Unbraked
> Manual gearbox kg
(lb)
> Automatic transmission braked on gradients up to 12 Ξ
> Manual gearbox kg
(lb)
> Automatic transmission kg
(lb) kg
(lb) braked on gradients up to 8 Ξ
> Manual gearbox kg
(lb)
> Automatic transmission kg
(lb)
–
500
(1102)
–
1000
(2204)
–
1000
(2204)
500
(1102)
500
(1102)
750
(1650)
1000
(2204)
750
(1650)
1000
(2204)
500
(1102)
500
(1102)
800
(1764)
1200
(2645)
800
(1764)
1200
(2645)
500
(1102)
500
(1102)
800
(1764)
1200
(2645)
Allowable trailer nose weight
Rear axle load limit kg
(lb) kg
(lb)
75
(165)
959
(2114)
75
(165)
959
(2114)
75
(165)
959
(2114)
800
(1764)
1200
(2645)
75
(165)
959
(2114)
Permitted gross weight
> Manual gearbox –
> Automatic transmission kg
(lb) kg
(lb)
1840
(4056)
1855
(4089)
1880
(4144)
1855
(4089)
1880
(4144)
1865
(4111)
1890
(4167)
190
Technical data
REFERENCE
Towing loads according to EU operating permit. Note and comply with different values in certain countries. Your MINI Service Centre will have details of possible increases.
Unbraked kg
(lb)
Cooper S
500
(1102)
Cooper D
500
(1102)
Cooper SD ALL4
500
(1102) braked on gradients up to 12 Ξ
> Manual gearbox kg
(lb)
> Automatic transmission kg
(lb)
750
(1650)
1000
(2204)
800
(1764)
1200
(2645)
800
(1764)
1200
(2645) braked on gradients up to 8 Ξ
> Manual gearbox kg
(lb)
750
(1650)
1000
(2204)
800
(1764)
1200
(2645)
800
(1764)
1200
(2645)
> Automatic transmission
Allowable trailer nose weight
Rear axle load limit kg
(lb) kg
(lb) kg
(lb)
75
(165)
997
(2197)
75
(165)
999
(2202)
75
(165)
997
(2197)
Permitted gross weight
> Manual gearbox
> Automatic transmission kg
(lb) kg
(lb)
1915
(4221)
1940
(4276)
1925
(4243)
1950
(4299)
1930
(4255)
1955
(4310)
191
REFERENCE
Filling capacities
Technical data
Fuel tank
Including a reserve of
Window washer system including headlight washers
Litres
(Imp. units) approx. 47
(approx. 99 pints) approx. 8
(1.8 gal) approx. 4
(8.5 pints)
Note
Further details: page
192
Maintenance overview
REFERENCE
Maintenance overview
The MINI maintenance system informs you about currently required maintenance work, see page
.
The following overview shows which servicing work is performed as part of which type of service.
Standard routines
Maintenance work
Check messages in Check Control
Check indicator and warning lights
Petrol
#
#
Diesel
#
#
Engine oil
Maintenance work
Change the engine oil and filter element
Air conditioning or automatic air conditioning:
Charged separately: replace microfilter
At every 2nd engine oil change:
Charged separately: renew spark plugs
At every 2nd engine oil change:
Intake silencer:
Charged separately: renew air cleaner element; if dust loads are relatively high, reduce the maintenance interval accordingly
At every 2nd engine oil change:
Charged separately: change fuel filter; change more frequently if fuel quality is poor
Reset the service display according to manufacturer's instructions
Petrol
#
#
#
#
#
Diesel
#
#
#
#
#
193
REFERENCE Maintenance overview
Front brake
Maintenance work
Change brake pads, clean brake calliper gaps
Brake discs:
Check surface and thickness.
Change if necessary, subject to additional charge
Reset the service display according to manufacturer's instructions
Rear brake
Maintenance work
Change brake pads, clean brake calliper gaps
Brake discs:
Check surface and thickness.
Change if necessary, subject to additional charge
Parking brake:
Check status, brake pad thickness and function
Reset the service display according to manufacturer's instructions
Brake fluid
Maintenance work
Change brake fluid
Parking brake:
Bed down and check functioning
Reset the service display according to manufacturer's instructions
Petrol
#
#
#
Diesel
#
#
#
Petrol
#
#
#
#
Diesel
#
#
#
#
Petrol
#
#
#
Diesel
#
#
#
194
Maintenance overview
Vehicle check
Maintenance work
Check operation of horn, headlight flasher and hazard warning flashers
Check instrument and inscription lighting and heater blower
Check the lights
Seat belts:
Check condition of belt, function of automatic reel, belt locking action and belt buckle
Check windscreen wiper and washer system
MINI Mobility System:
Check expiry date on the sealant cylinder.
Replace sealant cylinder if necessary, at extra charge
Tyres:
Check tread depth, tread wear pattern, external condition and inflation pressure; correct inflation pressure if necessary
Initialise the Run Flat Indicator
Battery with indicator light * :
Check battery.
Charge if necessary, subject to additional charge
Check coolant level and concentration, top up if necessary
Windscreen washer:
Check the fluid level and top up if necessary; if antifreeze needs to be added this will be subject to an additional charge
Brake lines and connections:
Check for leaks, damage and incorrect location
Vehicle underbody, including all visible parts:
Check for damage, corrosion, leak-tightness, incl. the leak-tightness of shock absorbers and assembly of springs in extended state
REFERENCE
#
#
#
#
#
#
#
Petrol
#
#
#
#
#
#
#
#
#
#
#
#
#
Diesel
#
#
#
#
#
#
195
REFERENCE Maintenance overview
Maintenance work
Steering components:
Check play, damage and wear
Check – by test-driving – operating safety of:
> Brakes
> Steering
> Shock absorbers
> Transmission
Reset the service display according to manufacturer's instructions
Petrol
#
Diesel
#
#
#
#
#
196
Maintenance overview
REFERENCE
197
REFERENCE From A to Z
From A to Z
INDEX
A
Accessories, see Your individual vehicle
Activated charcoal filter for automatic air-conditioning system
Adaptive brake lights
– dynamic brake lights
Adaptive Head Light
Additives
– coolant
– engine oil
Adjusting the interior temperature, see Air conditioner
Adjusting the interior temperature, see Automatic air-conditioning system
Adjusting the temperature
– air conditioner
– automatic air-conditioning system
Adjusting the volume
– according to speed
Air conditioner
Air conditioning mode
– air conditioner
– automatic air-conditioning system
– ventilation
Air distribution
– adjusting manually
– automatic
– individual
Air, drying, see Cooling function
Air flow rate
– air conditioner
– automatic air-conditioning system
– heating, ventilation
Air outlets
Air pressures, checking, see
Tyre pressures
Air recirculation, see
Recirculated-air mode
,
Air supply
– air conditioner
– automatic air-conditioning system
– ventilation
Air vents, see Air outlets
Air volume
Airbag switch, see Key switch for front passenger airbags
Airbags
– deactivating
– indicator light for front passenger's airbags
– reactivating
– safe seated position
– warning light
Alarm system
– avoiding false alarms
– interior movement detector
– switching off alarm
– tilt alarm sensor
All wheel drive, see ALL4
ALL4 four-wheel drive system
All-season tyres, see Winter tyres
Ambient air, see Recirculatedair mode
,
198
Ambient lighting
Ambient surrounding light, see
Ambient lighting
Antenna, general care
Antifreeze
– coolant
– washer fluid
Anti-lock Brake System ABS
Anti-theft alarm system, see
Alarm system
Approved engine oils
Aquaplaning
Armrest, see Centre armrest
Ashtray
Assistant systems, see
– Dynamic Stability Control
DSC
Audio equipment, external
AUTO programme for automatic air-conditioning system
Automatic
– air distribution
– air volume
– cruise control
– driving lights control
Automatic air conditioning
Automatic air-conditioning system
– automatic air distribution
Automatic start/stop function
Automatic station saving
Automatic station search
,
From A to Z
REFERENCE
Automatic transmission with
Steptronic
– interlock
– overriding selector-lever lock
– shiftlock
– towing away
– tow-starting
Automatic-dim mirrors
AUTOSTORE
AUX-In connection
AUX-In, see External audio device
Average fuel consumption
– setting units of measurement
Average speed
Avoiding false alarms
Axle load limits, see
Weights
B
Backrests, see Seats
Bar, see Tow-starting and towing away
Battery
– disposal
– jump-starting
– power failure
– recharging
Battery change
– remote control
Being towed
Belt tensioner, see Seat belts
Belts, see Seat belts
Blower, see Air volume
,
Boot lid, see Tailgate
Bottle holder, see Drinks holders
Brake assist
Brake discs
– brakes
– running in
Brake fluid, see Next Service indicator
Brake lights
– bulb changing
– Dynamic brake lights
Brake pads, running in
Brake system
– MINI Maintenance
System
– running in
Brakes
– ABS
– disc brakes
– Dynamic brake lights
– handbrake
– MINI Maintenance
System
– Next Service indicator
– running in
Brakes, see Safe braking
Breakdown Service, see Mobile
Service
Built-date
Bulb changing, see Lights and bulbs
Button for starting engine
Buttons in steering wheel
C
Call
– accepting
– rejecting
– terminating
Can holder, see Drinks holders
Car
– weight
Car phone
– installed position, see Centre armrest
Car wash, general care
Caravan-towing, see Towing a trailer
Care
– cushions and fabric covers
Care of paintwork
Care of your car
Carpets, general care
Carrying children in safety
Carwash
– before driving in
Catalytic converter, see Hot exhaust system
CBS Condition Based
Service
CD player
– fast forward, reverse
,
– hearing sample
– random play
,
– selecting tracks
,
– starting
– volume control
,
Central locking
– comfort access
– from inside
– from outside
– setting locking characteristics
Centre armrest
Centre brake light
Centre console, see Around the centre console
Centre rail
Centre rail, see Storage compartments
Changing a wheel
Changing bulbs
Changing bulbs, see Lights and bulbs
Check Control
Checking engine oil level
Child restraint systems
Child safety catches
Child seat mountings,
ISOFIX
Child seats
Chrome parts, general care
Cigarette lighter
– socket
Cleaning headlights
– washer fluid
199
REFERENCE From A to Z
Clearance warning, see Park
Distance Control PDC
Clock
– setting
– setting time
– 12-hour/24-hour mode
Closing
– from inside
Clutch, running in
Coat hooks
Cold start, see Starting the engine
Comfort access
– changing the battery
Comfort operation
– windows
Comfort/convenience, see
Around the centre console
Compartment for remote control, see Ignition lock
Compressed audio file
Compressed audio files
Computer
Condensation, see Car parked
Configuring settings, see
Personal Profile
Confirmation signals for locking/unlocking the vehicle
Connecting vacuum cleaner, see Connecting electrical appliances
Consumption display
– average consumption
Consumption display, see Fuel gauge
Consumption, see Average fuel consumption
Controls and displays
Convenient access
– in an automatic car wash
Convenient starting, see
Starting the engine
Coolant
– checking level
– temperature
– topping up
Coolant temperature
Cooling fluid, see Coolant
Cooling, maximum
Copyright
Cornering lights, see Adaptive
Head Light
Cup holder, see Drinks holders
Current fuel consumption
D
Dashboard lighting, see
Instrument lighting
Dashboard, see Displays
Data
– dimensions
– filling capacities
– weights
Data memory
Date
– setting
Date setting
Daytime running lights
DBC Dynamic Brake Control, see Brake assist
Deactivating/activating
Bluetooth connection
Deadlocking, see Locking
Defect
– tyres
Defogging windows
Defrost setting
,
Defrosting windows and removing mist
,
– air conditioner
– automatic air-conditioning system
Diesel particle filter
Digital radio
Dimensions
Dipstick, engine oil
Display lighting, see
Instrument lighting
Displays
– instrument cluster
Displays and controls
Displays, care
Disposal
– battery for remote control
– of coolant
– vehicle battery
Distance remaining to service, see Next Service indicator
Door key, see Key/remote control
Door locking, confirmation signals
Door locks
Doors, manual operation
Downhill gradients
Drinks holders
Drive-off assistant, see
– DSC
– Hill Start Assist
Driving area
Driving dynamics control, see
Sport button
Driving hints
Driving lights control, automatic
Driving lights, see Side lights/ low-beam headlights
Driving on left
Driving stability control systems
Dry air, see Cooling function
DSC Dynamic Stability
Control
DTC Dynamic Traction
Control
DTMF suffix dialling
Dynamic Brake Control DBC, see Brake assist
Dynamic brake lights
Dynamic Stability Control
DSC
200
From A to Z
REFERENCE
Dynamic Traction Control
DTC
E
EBV Electronic Brake Force
Distribution
Eject button
Electric windows
Electric windows, see
Windows
Electrical fault
– door lock
– fuel filler flap
Electronic Brake Force
Distribution
Electronic Stabilisation
Program ESP, see Dynamic
Stability Control DSC
Emergency operation, see
Manual operation
– door lock
– fuel filler flap
– transmission lock, automatic transmission
Emergency Service, see Mobile
Service
Engine
– overheated, see Coolant temperature
– running in
– starting
– starting, convenient access
– stopping
Engine compartment
Engine compartment lid
Engine coolant, see
Coolant
Engine oil
– adding
– additives, see Approved engine oils
– alternative oil grades
– approved engine oils
– checking level
– dipstick
– filling capacity
– intervals between changes, see Next Service indicator
– MINI Maintenance
System
Engine starting, see Starting the engine
Error messages, see Check
Control
ESP Electronic Stabilisation
Program, see Dynamic
Stability Control DSC
Exhaust system, see Hot exhaust system
Expanding the luggage area
Exterior mirror
– automatic dimming
Exterior mirrors
– automatic heating
– folding in and out
– towing a trailer
External audio equipment
,
Eyes
– for lashing loads
– for tow-starting and towing away
F
Failure message, see Check
Control
Failure of an electrical consumer
False alarms, avoiding
Fasten seat belts, see Seat belts
Fault
– door lock
– fuel filler flap
Fault messages, see Check
Control
Filling capacities
Filter
– micro-filter for air conditioner
– micro-filter/activated charcoal filter for automatic air-conditioning system
Fine wood, general care
First aid pouch
Fixture for remote control, see
Ignition lock
Flashing turn indicators
– front, changing
– indicator light
– rear, bulb changing
– side, bulb changing
Flashing when locking/ unlocking
Flat tyre
– indicator/warning light
– MINI Mobility System
– run-flat tyres
Flat tyre, see Condition of tyres
Floods, see Wading
Fog lights
– bulb changing
– indicator light
Folding rear-seat backrests
Foot mats, general care
Footbrake, see Safe braking
Footwell lights
For floor panel, see Flat luggage compartment floor
For your own safety
Forward
– CD
Forward CD
Four-wheel drive, see ALL4
Front airbags
Front fog lights
201
REFERENCE From A to Z
Front passenger airbags
– deactivating
– reactivating
Front seat adjustment
Frost protection
– coolant
– washer fluid
Fuel
– fuel gauge
– grade
– see Average fuel consumption
– see Fuel grade
– tank content
Fuel filler flap
– unlocking in the event of an electrical fault
Fuel level
Fuses
G
Gear indicator
– automatic transmission with
Steptronic
Gearshift lever
– automatic transmission with
Steptronic
– manual gearbox
Gearshift point display
Gearshifts
– with automatic transmission
– with manual gearbox
General care
– care products
– CD/DVD drives
– exterior
– high pressure cleaning jets
– interior
– leather
– vehicle washes
– washing by hand
– windows
General driving notes
Glass roof, electric
– convenient operation
– opening, closing
– raising
– remote control
Glass sunroof, electric
Glove compartment
Gong
– volume
,
Grilles, see Air outlets
Gross weight, see Weights
H
Halogen headlights
– bulb changing
– driving on left/right
– manual headlight beam throw adjustment
Handbrake
Hands-free unit
,
Hazard warning flashers
Head restraints
– safe seated position
Head-level airbag
Headlight
– beam throw adjustment
Headlight adjustment, see
Rule of the road
Headlight beam throw adjustment
– automatic for xenon headlights
Headlight courtesy delay feature
Headlight flasher
– indicator light
,
Headlight lenses
Headlights
– bulb changing
Headlights, general care
Hearing sample Scan
– CD
– Radio MINI Boost CD
Heating
– mirrors
– rear window
,
– seats
Heavy loads, see Loading
Height adjustment
– seats
– steering wheel
Height, see Dimensions
High-beam headlights
– bulb changing
– headlight flasher
– indicator light
Hill Start Assist
Hinged rear-seat backrests
Hints for driving, see Driving hints
Holder for drinks
Holder for telephone or mobile
– phone, see Snap-in adapter
Homepage
Horn
Hot exhaust system
I
Ice warning, see Outside temperature warning
Icy roads, see Outside temperature warning
Ignition
– switched off
– switched on
Ignition key position 1, see
Radio readiness
Ignition key position 2, see
Ignition on
Ignition key, see Key/remote control
Ignition lock
Imprint
Incoming call
Indicator and warning lights
,
Indicators, see Flashing turn indicators
202
From A to Z
REFERENCE
Individual air distribution
Individual settings, see
Personal Profile
Inflation pressure monitoring, see Run Flat Indicator
Inflation pressure, tyres
Initialising
– glass roof, electric
– Run Flat Indicator RPA
Instrument cluster, see
Displays
Instrument lighting
Instrument panel, see
Cockpit
Integrated key
Interior light
– remote control
Interior mirror
– automatic-dim
Interior movement detector
Interlock
Intermittent wiper operation
ISOFIX child seat mountings
J
Jack
– mounting points
Jacking points
Jump-starting, see Starting with a flat battery
K
Kerb weight, see Weights
Key Memory, see Personal
Profile
Key switch for front passenger airbags
Keyless Go, see Convenient access
Keyless locking and unlocking, see Comfort access
Keys, see Key/remote controls
Kick-down
– automatic transmission with
Steptronic
Knock control
L
Lap-and-shoulder seat belt
Lashings, see Securing the load
Laying up out of use
Leather care
LEDs light-emitting diodes
Length, see Dimensions
Level load platform
Licence plate light
– bulb replacement
Light
– automatic driving lights control
Light switch
Light-emitting diodes
LEDs
Lighter
Lighting
– instruments
– lights and bulbs
– vehicle, see Lights
Light-metal alloy wheels, general care
Lights and bulbs, bulb change
Lights, see Side lights/lowbeam headlights
Limit
Loads
– loading
– securing
– trailer
– vehicle
Load-securing equipment, see
Securing the load
Lockable wheel studs, see
Thief-proof wheel studs
Locking
– adjusting confirmation signal
– from inside
– from outside
– without remote control, see
Convenient access
Longlife oils
– alternative oil grades
– approved engine oils
Low fuel level warning light
Low-beam headlights
– automatic
– bulb changing
Luggage area
– convenient access
– light
Luggage compartment
– doors, see Tailgate
– lid, see Tailgate
– opening from outside
– volume
Luggage compartment partition net, see Partition net
Luggage rack, see Roof rack
Luggage-area light
Lumbar support
M
M+S tyres, see Winter tyres
Maintenance system
Manual air distribution
Manual gearbox
Manual operation
– automatic transmission with
Steptronic
– door lock
– fuel filler flap
– transmission interlock, automatic transmission
203
REFERENCE From A to Z
Manual station search
,
Master key, see Key/remote control
Maximum cooling effect
Measurements, see
Dimensions
Micro-filter
– for air conditioner
– for automatic airconditioning system
– MINI Maintenance
System
Micro-filter/activated charcoal filter
– MINI Maintenance
System
Microphone for telephone
MINI Maintenance System
MINI website
Minimum volume
Mirrors
– exterior mirrors
– heating
– inside mirror
Mobile phone
– adjusting volume
– connecting, see Pairing a mobile phone
– installed position, see Centre armrest
– pairing
– what to do if...
Mobile phone, installed position, see Centre armrest
Mobile Service
Mobility System
Modifications, technical, see
For your own safety
MP3
Multi-function lever
– see Flashing turn indicators/ headlight flasher
Multifunction switch
– see Wiper system
Multifunctional steering wheel, see Buttons on the steering wheel
Music track
– hearing sample
– random sequence
N
Neck restraints, see Head restraints
Nets, see Storage compartments
New tyres
Next Service indicator, see
Condition Based Service
CBS
Nose weight
,
Nozzles, see Air outlets
Nozzles, see Ventilation
Number of seat belts
Nylon rope, see Towrope
O
OBD socket, see Socket for onboard diagnosis
Octane numbers, see Fuel grade
Odometer
Oil consumption
Oil grades
Oil level
Oil, see Engine oil
Old batteries, see Disposal
Opening and closing
– convenient access
– from inside
– from the outside
– via the door lock
– via the remote control
Opening and unlocking
– from the inside
Opening, see Unlocking
Outlets
– see Ventilation
Outside mirrors
– adjusting
Outside temperature display
– changing units of measure
– in computer
Outside temperature warning
Outside-air mode
– automatic air-conditioning system
Overheated engine, see
Coolant temperature
P
Paint, general care
Park Distance Control PDC
Parking aid, see Park Distance
Control PDC
Parking brake, see
Handbrake
Parking lights
– bulb changing
Particle filter, see Diesel particle filter
Partition net
Parts and accessories, see Your individual vehicle
PDC
– volume
PDC Park Distance Control
Personal Profile
Petrol, see Fuel grade
phone
Phone call
– ending
Phone number
– dialling
Placing a call, see Dialling a phone number
Plasters, see First aid pouch
Plastic parts, general care
204
From A to Z
REFERENCE
Pollen
– see Micro-filter for air conditioner
– see Micro-filter/activated charcoal filter for automatic air-conditioning system
Power failure
Preheating, see Cars with diesel engine
Pressure monitoring, tyres
– Run Flat Indicator
Pressure, tyres
Programme type
Protective function, see Trap protection
– windows
PTY
Pull-away assistant, see Hill
Start Assist
Puncture
– Run Flat Indicator
Punctures
– run-flat tyres
R
Radio
Radio MINI Boost CD
– Autostore
– digital radio
– retrieving station
– saving station
– scanning station
– search for station
– setting tone
– switching on/off
– volume
Radio MINI CD
– recalling a station
– sampling a station
– searching for station
– setting tone
– switching on/off
– volume
Radio position, see Radio readiness
Radio readiness
– switched off
– switched on
Radio-control key, see Key/ remote control
Rain sensor
Range
RDS
Reading lights
Rear fog light
– indicator light
Rear lights
– bulb changing
Rear luggage rack
Rear seats
– adjusting
– folding backrests
Rear window
– window wiper
Rear window heating
,
Rear-seat backrests, hinged
Rear-view mirror, see
Mirrors
Reception
– quality
– radio stations
– regional programme
Recirculated-air mode
,
Recirculation of air, see
Recirculated-air mode
Reclining seat, see Seat back
Recycling
Refuelling
Regional programme
Releasing
– engine compartment lid
Remote control
– changing the battery
– comfort access
– faults
,
– service data
– tailgate
Remote control, replacement
Reserve warning, see Fuel gauge
Reservoir for washer fluid
Reset, see Resetting the tone settings
RESET?
Residual distance, see
Range
Restraint systems
– for children
– see Seat belts
Returning end-of-life vehicles, see Recycling
Reverse
– CD
Reverse CD
Reverse gear
– automatic transmission with
Steptronic
– manual gearbox
– bulb changing
Revolution counter
Roadworthiness test, see Next
Service indicator
RON, see Fuel grade
Roof load
Roof rack
Rope, see Tow-starting and towing away
RPA, see Run Flat Indicator
RSC Runflat System
Component, see Run-flat tyres
Rubber parts, general care
Rule of the road, headlight adjustment
Run Flat Indicator RPA
– indicating a flat tyre
– initialising the system
– snow chains
– system limits
Runflat System Component
RSC, see Run-flat tyres
205
REFERENCE From A to Z
Run-flat tyres
– flat tyre
– replacing tyres
– tyre pressure
– winter tyres
RunFlat Tyres, see Run-flat tyres
Running in the final drive
Running in
S
Safe seated position
– airbags
– seat belts
– with head restraints
Safety lock buttons on doors, see Locking
Safety switch for back seat windows
Safety system
– driving stability control systems
Safety systems
– airbags
– Anti-lock Brake System
ABS
– Dynamic Stability Control
DSC
– seat belts
Safety tyres, see Run-flat tyres
Saving energy
– gearshift point display
Scan, hearing a sample
– Radio MINI CD
Scan, hearing sample
– CD player
– Radio MINI Boost CD
Scanning tracks Scan
– CD
Screw thread for towing eye
Search
– CD player
,
– radio
Search run
– Radio MINI CD
Search track
– CD
Search track CD
Seat adjustment
– mechanical
– rear
Seat belt reminder, see 'Fasten seat belts' reminder
Seat belts
– 'Fasten seat belts' reminder
– damage
– indicator light
– number of
– rear centre seat belt
– safe seated position
Seat belts, general care
Seats
– adjusting
– heating
– safe seated position
Securing the load
Securing the load, see
Loads
Securing, vehicle
– from inside
– from outside
Selector lever
– automatic transmission with
Steptronic
Selector lever lock
– automatic transmission with
Steptronic, see Shiftlock
– overriding manually
Selector lever positions
– automatic transmission with
Steptronic
Service
Service data in the remote control
Service Interval indicator, see
Condition Based Service
CBS
Service requirements
Service, see Mobile
Service
Service vehicle, see Mobile
Service
Setting time format
Settings
– clock, 12-hour/24-hour mode
Settings and information
Shift paddles
Shifting gears
– automatic transmission with
Steptronic
– manual gearbox
Shiftlock
– automatic transmission, see
Changing selector lever positions
Side airbags
Side flashing turn indicators
– bulb changing
Side lights, bulb changing
Side lights/low-beam headlights
Side windows, see Windows
Signal horn, see Horn
Slot for remote control
Smokers' package, see
Ashtray
Snap-in adapter
– inserting/removing
– use
Snap-in adapter, see Centre armrest storage compartment
Snow chains
Socket for on-board diagnosis
OBD
Socket, see Connecting electrical appliances
Soot particle filter, see Diesel particle filter
Sound
– middle setting
Special oils, see Approved engine oils
206
From A to Z
REFERENCE
Speed
– when towing a trailer
Speed limit
– with winter tyres
Speedometer
Speed-related volume
Split rear-seat backrests, see
Expanding the luggage area
Sport button
Sport programme
– automatic transmission with
Steptronic
Stability control, see Driving stability control systems
Start/stop button
– starting the engine
– switching off the engine
Starting on uphill gradients, see Hill Start Assist
Starting the engine
– start/stop button
Starting with a flat battery
Station, see Radio MINI Boost
CD
Station, see Radio MINI CD
Status at time of printing
Steering wheel
– adjusting
– buttons on the steering wheel
– lock
– shift paddles
Steptronic, see Automatic transmission with
Steptronic
Stop light, see Rear lights
– bulb changing
Stopping
– engine
– vehicle
Storage compartments
Storage space
– luggage area
– storage compartments
Storing tyres
Stowage, see Storage compartments
Summer tyres, see Wheels and tyres
Sun roof
– see Glass roof, electric
Switch for front passenger airbags
Switches, see Driving area
Switching cooling function on and off
Switching off the engine
– start/stop button
Switching on/off
– CD player
,
,
– Radio MINI Boost CD
– Radio MINI CD
Symbols
T
Tail lights, see Rear lights
Tailgate
– convenient access
– opening from outside
– opening/closing
– unlocking with the remote control
Tank capacity, see Filling capacities
Technical data
Technical modifications
Telephone
– hands-free unit
– installed position, see Centre armrest
– voice input
Temperature display
– setting unit of measurement
Temperature of the coolant, see Coolant temperature
Tempomat, see Cruise control
Tensioning straps, see
Securing the load
Theft protection
– for wheel studs, see
Thief-proof wheel studs
Thief-proof wheel studs
Third brake light, see Centre brake light
Tightening torque, see
Tightening the wheel studs
Tilt alarm sensor
Time
Tone
– setting
,
Top speed
– when towing a trailer
Torque
– wheel studs
Towbar
Towing a trailer
Towing away
– cars with automatic transmission
– methods
Towing eye
– screw thread
Towing eyes for tow-starting and towing away
Towrope
Tow-starting
TP, see Traffic reports
,
Track
– scanning track
Track width, see
Dimensions
Traffic reports
– displays
– switching on/off
– volume control
Trailer pulling, see Towing a trailer
Trailer tow hitch
Trailer towing
– towing loads and gross weight
207
REFERENCE From A to Z
Transmission
– automatic transmission with
Steptronic
– manual gearbox
– overriding selector-lever lock for automatic transmission with Steptronic
Transport securing equipment, see Securing the load
Transporting children
Trap protection
– windows
Tread depth, see Minimum tread depth
Trip distance recorder
Triple turn signal
Turning circle, see
Dimensions
Tyre changing, see New wheels and tyres
Tyre pressure
– loss
Tyre pressure monitoring, see
Run Flat Indicator
Tyre pressures
Tyre puncture
– Run Flat Indicator
Tyres
– age
– changing, see Changing a wheel
– condition
– damage
– minimum tread depth
– new
– pressure monitoring, see Run
Flat Indicator
– pressures
– punctures
– run-flat tyres
– running in
– size
– wear indicators, see
Minimum tread depth
– winter tyres
Tyres with emergency running properties
– Run Flat Indicator
Tyres with emergency running properties, Run-flat tyres
U
Units of measurement
– average fuel consumption
– temperature
Unlocking
– from outside
– setting unlocking characteristics
– tailgate
– without remote control, see
Convenient access
Unlocking and locking doors
– confirmation signals
– from inside
– from outside
Upholstery, general care
USB audio interface
V
Vehicle
– battery
– dimensions
– Identification Number, see
Engine compartment
– laying up out of use
– loads
– returning, see Recycling
– running in
– stopping
Vehicle battery, see Vehicle battery
Vehicle Identification Number, see Engine compartment
Vehicle jack
Vehicle key, see Key/remote control
Vehicle phone, see
Telephone
Vehicle radio, see Radio MINI
Boost CD
Vehicle radio, see Radio MINI
CD
Vehicle recycling, see
Recycling
Vehicle washes
Ventilation
– air conditioner
Ventilation, see Climate
Voice input
– telephone
Voice-activated phone book
Volume
– gong
,
– mobile phone
– PDC
,
Volume control
– traffic reports
Volume of the luggage compartment
W
Wading
Warning and indicator lights
,
Warning messages, see Check
Control
Warning triangle
Washer fluid
– reservoir capacity
Washer fluid reservoir for cleaning systems
Washer jets, see Windscreen washer jets
Washing by hand
Waste tray, see Ashtray
Water on roads, see Wading
Waterfall lighting, see Ambient lighting
Wear indicators in the tyres, see Minimum tread depth
208
From A to Z
Website
Weights
Welcome lights
Wheel studs
– torque
,
Wheelbase, see
Dimensions
Wheels and tyres
Wheels, new
Wheelslip control, see
– Dynamic Stability Control
DSC
Width, see Dimensions
Window lifter
– safety switch
Window washer reservoir, see
Washer fluid
– content, see Filling capacities
Window washer system
– washer fluid
– washer jets
Windows
– closing
– comfort operation
– opening
– safety switch
– trap protection
Windscreen
– cleaning
– defrosting
Windscreen defrosting, see
Defrosting windows
Windscreen wiper blades, changing
Winter tyres
– tyre storage
Wiper blades, general care
Wiper system
– washer fluid
WMA
Working in the engine compartment
X
Xenon headlights
– automatic headlight beam throw adjustment
– bulb changing
– driving on left/right
Y
Your car
REFERENCE
209
*BL260751200N*
DRIVE ME.
Online Edition for Part no. 01 40 2 607 512 - © 03/11 BMW AG
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement