Mitsubishi Electric SD205U User manual

ENGLISH
EN
DATA PROJECTOR
MODEL
XD205U
SD205U
User Manual
XD205
SD205
This User Manual is important to you.
Please read it before using your projector.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product’s enclosure that may be of suffcient magnitude to constitute a
risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you use
another power supply cord, it may cause interference with
radio and television reception.
Use the attached RGB cable with this equipment so as to keep
interference within the limit of an FCC Class B device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN
THE PROJECTOR IS IN THE POWER ON MODE.
CAUTION
Not for use in a computer room as defined in the Standard for
the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.
The attached power cords are to be used exclusively for this
product. Never use them for other products.
Note: This symbol mark is for
EU countries only.
This symbol mark is according to the directive 2002/96/
EC Article 10 Information for
users and Annex IV.
EN-2
When using the projector in Europe:
COMPLIANCE NOTICE
This Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 92/
31/EEC and 93/68/EEC, and 73/23/EEC "Low Voltage Directive" as amended by Directive 93/68/ EEC.
The electro-magnetic susceptibility has been chosen at a level
that gains proper operation in residential areas, on business
and light industrial premises and on small-scale enterprises,
inside as well as outside of the buildings. All places of operation are characterized by their connection to the public low voltage power supply system.
WARNING
Use the attached RGB cable with this equipment so as to keep
interference within the limits of an EN55022 Class B device.
Please follow WARNING instructions.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high
quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life,
should be disposed of separately from your household waste.
Please, dispose of this equipment at your local community waste collection/
recycling centre.
In the European Union there are separate collection systems for used electrical
and electronic product.
Please, help us to conserve the environment we live in!
Important safeguards..........................................................................................................................4
Overview.............................................................................................................................................6
Remote control ...................................................................................................................................8
Installation ..........................................................................................................................................9
Basic connections.............................................................................................................................10
Preparation .......................................................................................................................................12
Basic operation .................................................................................................................................13
Menu operation.................................................................................................................................15
Image adjustment .............................................................................................................................18
Advanced feature..............................................................................................................................20
Lamp replacement............................................................................................................................22
Troubleshooting ................................................................................................................................23
Indicators ..........................................................................................................................................26
Specifications ...................................................................................................................................27
Declaration of Conformity
Model Number :
Trade Name :
Responsible party :
Telephone number :
XD205U/SD205U
MITSUBISHI ELECTRIC
Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road, Irvine, CA 92618 U.S.A
+1-(949) 465-6000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
DLP™, Digital Micromirror Device and DMD are all trademarks of Texas Instruments.
Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-3
ENGLISH
Contents
Important safeguards
1.
Read instructions
All the safety and operating instructions should be read
before the appliance is operated.
11. Power-cord protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at plugs,
convenience receptacles, and points where they exit from
the appliance. Do not put the power cord under a carpet.
2.
Retain instructions
The safety and operating instructions should be retained
for future reference.
12. Overloading
Do not overload wall outlets and extension cords as this
can result in a fire or electric shock.
3.
Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
4.
Instructions
All operating instructions must be followed.
13. Objects and liquids
Never push objects of any kind through openings of this
projector as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
5.
Cleaning
Unplug this projector from the wall outlet before cleaning
it. Do not use liquid aerosol cleaners. Use a damp soft
cloth for cleaning.
Please read all these instructions regarding your projector and
retain them for future reference. Follow all warnings and
instructions marked on the projector.
6.
Attachments and equipment
Never add any attachments and/or equipment without the
approval of the manufacturer as such additions may result
in the risk of fire, electric shock or other personal injury.
7.
Water and moisture
Do not use this projector near water or in contact with
water.
8.
Accessories
Do not place this projector on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod
bracket, or table recommended by the manufacturer or
sold with the projector. Any mounting of the appliance
should follow the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
14. Servicing
Do not attempt to service this projector yourself. Refer all
servicing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the
projector.
(c) If the projector does not operate normally after you follow the operating instructions. Adjust only those controls that are covered by the operating instructions. An
improper adjustment of other controls may result in
damage and may often require extensive work by a
qualified technician to restore the projector to its normal operation.
(d) If the projector has been exposed to rain or water.
(e) If the projector has been dropped or the cabinet has
been damaged.
(f) If the projector exhibits a distinct change in performance - this indicates a need for service.
16. Replacement parts
When replacement parts are required, be sure that the
service technician has used replacement parts specified
by the manufacturer or parts having the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
An appliance and cart combination should be moved with
care. Quick stops, excessive force and uneven surfaces
may cause the appliance and cart combination to overturn.
9.
Ventilation
Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the projector and to
protect it from overheating. Do not block these openings or
allow them to be blocked by placing the projector on a bed,
sofa, rug, or bookcase. Ensure that there is adequate ventilation and that the manufacturer’s instructions have been
adhered to.
10. Power sources
This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power, please consult your appliance
dealer or local power company.
EN-4
17. Safety check
Upon completion of any service or repair to this projector,
ask the service technician to perform safety checks determining that the projector is in a safe operating condition.
Unplug immediately if there is something wrong
with your projector.
Do not operate if smoke, strange noise or odor comes out of
your projector. It may cause fire or electric shock. In this case,
unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inadvertent
contact may result in an electric shock. Except as specifically
explained in User Manual, do not attempt to service this product by yourself. Please contact your dealer when you want to
fix, adjust, or inspect the projector.
Do not touch the air outlet grilles and bottom plate.
Do not touch them or put other equipment close to the air outlet grilles because they become hot during operation. The
heated air outlet grilles and bottom plate may cause injury or
damage to other equipment. Also, do not put the projector on a
desk that is easily affected by heat.
Do not look into the air outlet grilles when projector
is operating.
Heat, dust, etc. may blow out of them and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the projector,
causing deterioration in the projector quality and fire.
Do not modify the projector.
Place of installation
It can lead to fire or electric shock.
For safety’s sake, do not use the projector at any place subjected to high temperature and high humidity. Please maintain
an operating temperature, humidity, and altitude as specified
below.
• Operating temperature: between +41°F (+5°C) and +95°F
(+35°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the projector to
prevent the projector from being overheated.
• Do not install the projector at a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that produces a strong magnetic field. Also refrain from installing
the projector near any cable carrying a large amount of current.
• Place the projector on a solid, vibration-free surface. Otherwise it may fall, causing serious injury or damage.
• Do not stand the projector on its end. It may fall, causing
serious injury or damage.
• Slanting the projector more than ±10° (right and left) or ±15°
(front and rear) may cause trouble or explosion of the lamp.
• Do not place the projector near air-conditioning unit or
heater to avoid the air outlet and inlet grilles from being
exposed to hot air.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged, unplug
the projector and contact your dealer for inspection. It may
lead to fire if you keep using the damaged projector.
Do not face the projection lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projector on a level and stable surface only.
Do not look into the lens when the projector is operating.
It may hurt your eyes. Never let children look into the lens
when the projector is on.
Do not unplug the power cord during operation.
It can lead to lamp breakage, fire, electric shock or other trouble. Wait for the fan to stop before unplugging the power cord.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user’s authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN-5
ENGLISH
WARNING:
Overview
2
3
1
4
5
10
1
2
3
4
5
6
7
8
9
10
11
FOCUS ring
ZOOM ring
Control panel
Air outlet grille
Remote control sensor (Front)
Air inlet grille
Air inlet grille
Terminal board
Kensington Security Lock Standard connector
Air inlet grille
Speaker
1
2
3
4
5
6
7
8
9
Power button
AUTO POSITION / S button
COMPUTER / W button
MENU button
STATUS indicator
POWER indicator
KEYSTONE/ENTER button
VIDEO/ X button
T button
11
9
8
6
7
Control panel
2
3
8
9
7
4
1
Important:
6
5
• While the menu or the screen for the keystone adjustment
or password entry is being displayed, the COMPUTER,
VIDEO, and AUTO POSITION buttons function as the W, X,
and S buttons respectively.
• While the menu is on the screen, the KEYSTONE button
functions as the ENTER button.
Terminal board
4
5
EN-6
12
3
1
7
2
10 11 8 9
6
5
1
2
3
4
5
6
7
8
9
10
11
12
Power jack
COMPUTER IN terminal (Mini D-SUB 15-pin)
MONITOR OUT terminal (Mini D-SUB 15-pin)
Remote control sensor (Rear)
Foot adjustment buttons (Left/Right)
Air inlet grille
USB (PC) terminal
AUDIO IN terminal (Mini jack)
AUDIO OUT terminal (Mini jack)
S-VIDEO terminal
VIDEO terminal
Kensington Security Lock Standard connector
1
2
ENGLISH
Bottom side
Lamp cover
Adjustment feet
Caution:
Do not replace the lamp immediately after using the projector
because the lamp would be extremely hot and it may cause
burns.
1
2
Remote control
14
ON
POWER OFF
1
2
13
STILL
MUTE
UP
PAGE
AUTO POSITION
3
4
12
DOWN
11
ENTER
5
16:9
MENU
10
COMPUTER
9
VIDEO
6
1
2
8
KEYSTONE
VOLUME
7
1 ON button
2 STILL button
3 AUTO POSITION button
4 ENTER button
5 MENU button
6 KEYSTONE button
7 +, - (VOLUME) buttons
8 VIDEO 1, 2 button
9 COMPUTER button
10 16 : 9 button
11 Direction buttons
12 PAGE UP / DOWN button
13 OFF button
14 MUTE button (Audio/Video)
• The + and - buttons are used in the KEYSTONE adjustment
in addition to the volume control.
EN-7
Remote control
Battery installation
Use two AAA size batteries.
1.
Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.
2.
Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
• Load the batteries from - spring side, and make sure to set them tightly.
3.
Replace the back cover.
Caution:
•
•
•
•
•
•
•
•
•
•
Use of a battery of wrong type may cause explosion.
Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
Dispose of used batteries according to your local regulations.
Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.
Be sure to handle the battery according to the instructions.
Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
Keep batteries out of reach of children and pets.
Remove the battery, if the remote control is not used for a long time.
Do not combine a new battery with an old one.
If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your
eyes, rinse them with water and then consult your doctor.
Operation range (of the remote control)
The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is pointed at the
remote control sensor of the projector. When the remote control is pointed to the screen, the distance
from the remote control to the projector via the screen should be 5 m or less. However, the operation distance varies depending on
the type of the screen used.
Reception angle (vertical)
20
10
Reception angle (horizontal)
20
10
Reception angle (vertical), ceiling mount
20
30
20
30
Important:
• Do not expose the remote control sensor to direct sunlight or fluorescent. Keep a distance at least 2 m (6.5 feet) between the
remote control sensor and the fluorescent light to ensure correct operation of the remote control.
Inverted fluorescent light, if located near the projector, may interfere the remote control.
• When you use the remote control too close to the remote control sensor, the remote control may not work correctly.
EN-8
Installation
ENGLISH
Layout of the projector
Image size varies depending on the distance between the screen and the projector.
Front projection
W
B
Hd
H
A
A=B
L
L : Between the screen and the front edge of the projector
Hd : Height of the projected image
XD205U/SD205U
Screen
Diagonal size
Distance from the screen : L
Width : W
Height : H
MINIMUM
Zoom (WIDE)
Hd
MAXIMUM
Zoom (TELE)
inch
cm
inch
cm
inch
cm
inch
m
inch
m
inch
cm
40
60
80
100
150
200
250
300
102
152
203
254
381
508
635
762
32
48
64
80
120
160
200
240
81
122
163
203
305
406
508
610
24
36
48
60
90
120
150
180
61
91
122
152
229
305
381
457
50
76
101
126
189
252
315
378
1.3
1.9
2.6
3.2
4.8
6.4
8.0
9.6
61
91
121
151
227
302
378
–
1.5
2.3
3.1
3.8
5.8
7.7
9.6
–
3.5
5.2
7.0
8.7
13.1
17.4
21.8
26.1
8.8
13.3
17.7
22.1
33.2
44.2
55.3
66.3
• The above figures are approximate and may be slightly different from the actual measurements.
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit designed
for this projector. Ask a specialist for installation.
For details, consult your dealer.
• The warranty on this projector does not cover any damage
caused by use of any non-recommended ceiling mount kit or
installation of the ceiling mount kit in an improper location.
• When using the projector mounted on the ceiling, set
IMAGE REVERSE in the INSTALLATION menu to MIRROR
INVERT. See page 16.
• When the projector is mounted on the ceiling, images may
appear darker than those projected in the case of tabletop
mounting. This isn’t a product malfunction.
Rear projection
Ask a specialist for installation. For details, consult your dealer.
• For rear projection, set IMAGE REVERSE in the INSTALLATION menu to MIRROR. See page 16.
Caution:
• Placing the projector directly on a carpet impairs ventilation
by the fans, causing damage or failure. Put a hard board
under the projector to facilitate ventilation.
• Place the projector at least 50 cm (or 20 inch) away from the
wall to prevent the air inlet grille and the air outlet grilles that
emit hot air from being blocked.
• Do not use the projector in the following locations and manners, which may cause fire or electric shock.
• In a dusty or humid place.
• In a sideways or upside-down position.
• Near a heater.
• In an oily, smoky, or damp place such as a kitchen.
• In direct sunlight.
• Where the temperature rises high, such as in a closed
car.
• Where the temperature is lower than +41ºF (or +5ºC) or
higher than +95ºF (or +35ºC ).
Important:
• Do not apply force to the lens, because the lens may be
damaged.
EN-9
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal computer that
have analog RGB output connectors.
Important:
• Make sure that the connected device is turned off before starting connection.
• Plug in the power cords of the projector and the connected devices firmly. When unplugging, hold and pull the plug. Do not pull the
cord.
• When the projector and the connected devices are located too close to each other, the projected image may be affected by their
interference.
• See the owner’s guide of each device for details about its connections.
Projector + AV device
S-VIDEO IN
(option)
AUDIO IN
(option)
to audio output (L)
to audio output (R)
VCR, etc.
to S-video output
Important:
• Match the colors of the video and audio plugs on the Audio cable with those of the terminals.
• Speaker output is mono.
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such DVD player with this projector, use
the COMPUTER IN terminal.
Audio cable (option)
DVD player or HDTV decoder
Y
CB(PB) CR(PR)
to audio output
BNC - RCA connector (option)
No connection
G
B
R
HD/CS
VD
COMPUTER IN
Mini D-SUB 15-pin - BNC
conversion cable (option)
Important:
•
•
•
•
•
•
The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
The terminal’s names vary depending on the connected devices.
Use a Mini D-SUB 15-pin - BNC conversion cable for connection.
Image may not be projected correctly with some DVD players.
When connecting a HDTV decoder having RGB output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
Speaker output is mono.
EN-10
ENGLISH
Projector + Computer
For computer with Mini D-SUB
RGB cable for PC
COMPUTER IN
Computer
AUDIO IN
to monitor
port
AUDIO OUT
AUDIO OUT
Audio cable (option)
MONITOR OUTPUT
MONITOR OUT
Necessary when outputting to both
a PC monitor and the projector.
RGB cable for PC (option)
PC audio cable (option)
to PC audio
output
Important:
• When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly.
• Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your
dealer for further information.
• This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected computer and
prepare a proper cable for connection. Some computers don’t have the audio output terminal.
• Speaker output is mono.
• When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.
For Macintosh
• If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information.
• Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer for further
information.
About DDC
The COMPUTER IN terminal of this projector complies with the DDC1/2B standard. When a computer supporting this standard is
connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate images.
• After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first,
and then boot up the computer.
• You may need to install the DDC driver, depending on the computer you use. In this case, you need to download the driver from
our Web site. Contact your dealer or Mitsubishi sales office for further information.
EN-11
Preparation
Preparation for projection
1.
Tilt up the project to the appropriate angle.
1.
2.
Press the foot adjustment buttons next to the adjustment
feet (rear), and the adjustment feet will come out.
3.
Release the buttons to lock the adjustment feet (rear) to
that position.
4.
Rotate the adjustment feet (rear) for fine adjustment.
Attach the provided power cord to the projector.
2.
Plug the power cord in the wall outlet.
3.
Remove the lens cap.
Warning:
• Do not look into the lens directly when the projector is on.
• The lens cap is for protecting the lens. If you leave the lens
cap on the lens with the projector turned on, it may be
deformed because of heat build-up. Remove the lens cap
when you turn on the projector.
• The power cords for use in the U.S. and Europe are provided with this projector. Use the appropriate cord for your
country.
• This projector uses the power plug of three-pin grounding
type. Do not remove the grounding pin from the power plug.
If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.
• The provided power cord for the U.S. is rated at 120 V.
Never connect this cord to any outlet or power supply using
other voltages or frequencies than rated. If you want to use
a power supply using other voltage than rated, prepare an
appropriate power cord separately.
• Use 100-240 V AC 50/60 Hz to prevent fire or electric
shock.
• Do not place any objects on the power cord or do not place
the projector near heat sources to prevent damage to the
power cord. If the power cord should be damaged, contact
your dealer for replacement because it may cause fire or
electric shock.
• Do not modify or alter the power cord. If the power cord is
modified or altered, it may cause fire or electric shock.
5.
Put the adjustment feet (rear) back into the projector by
pressing the foot adjustment buttons.
Important:
• If necessary, rotate the adjustment feet (front) for fine
adjustment.
• Install the screen on a flat wall at 90 degrees to the floor.
• Slanting the projector more than ±10° (right and left) or ±15°
(front and rear) may cause trouble or explosion of the lamp.
You can tilt the projector up to 7 degrees using the adjustment feet only.
• Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4:3, depending on the installation
conditions of the projector and the screen.
• To correct vertical keystone distortion, press the KEYSTONE button on the projector or the remote control to display KEYSTONE, and adjust the image by pressing the S,
T button (or VOLUME +, - button on the remote control).
In the following cases:
Press the T
(or -) button.
Caution:
• Plug in the power cord firmly. When unplugging, hold and
pull the power plug, not the power cord.
• Do not plug in or out the power cord with your hand wet. It
may cause electric shock.
Adjustment of the projection angle
For the best projection, project images on a flat screen
installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.
Screen
Adjustment feet
EN-12
After using the projector:
Press the S
(or +) button.
Important:
• When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a
projection angle.
• The allowable range of the adjustment value in the keystone
adjustment varies depending on the installation conditions.
• When the keystone adjustment takes effect, the resolution
decreases. In addition, stripes may appear or straight lines
may bend in images with complicated patterns. They are
not due to product malfunctions.
• Noise may appear on the screen during the keystone
adjustment because of the type of the video signal being
projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in
the range where the image is displayed without noise.
• When the keystone adjustment is carried out, the image
may not be displayed correctly because of the type of input
signal.
For SD205U only
• When the 720p or 1080i signal is input, the keystone adjustment ranges are limited.
ENGLISH
Basic operation
4
3
6
ON
POWER OFF
STILL
MUTE
1, 2
UP
PAGE
AUTO POSITION
DOWN
ENTER
16:9
MENU
5
5
COMPUTER
5
VIDEO
3, 1, 2
Power-on
1.
Turn on the device connected to the projector first.
2.
Plug the power cord in the wall outlet.
• The POWER indicator lights up.
• If the power cord is unplugged from the wall outlet
before the projector is cooled down completely after
use, the fans may start rotating when the power cord is
plugged in next time and the POWER button may not
function. In this case, wait for the fans to stop and press
the POWER button to light the indicator.
3.
STATUS
POWER
Stand-by
-
Red
When the lamp is on.
Green
Green
Condition
2
KEYSTONE
VOLUME
• Images may not be projected with good quality in an
extremely hot or cold environment. (This is not a product
malfunction.)
4.
Adjust the focus by turning the focus ring.
5.
Choose your desired external input source using the
COMPUTER or VIDEO button.
• The input source is switched from VIDEO to COMPUTER at the press of the COMPUTER button on the
control panel.
• The input source is switched between VIDEO(1) and SVIDEO(2) at every press of the VIDEO button on the
control panel.
• The projector automatically selects the appropriate signal format. The selected signal format is displayed on
the screen.
• The COMPUTER and VIDEO buttons don’t function
while the menu is being displayed.
• When COMPUTER is chosen as the source, images
supplied from the computer may flicker. Press the W or
X button on the remote control to reduce flicker, if it
occurs.
• To avoid permanently imprinting a fixed image onto
your projector, please do not display the same stationary images for long period.
6.
Adjust the image size by turning the zoom ring.
• If necessary, adjust the focus and zoom again.
Press the POWER button on the control panel or the ON
button on the remote control.
• It may take about one minute for the lamp to light up.
• The lamp occasionally fails to light up. Wait a few minutes and try to light the lamp again.
• After the POWER button is pressed, the image may
flicker before the lamp becomes stable. This is not a
product malfunction.
• Regardless of the setting of LAMP MODE in the
INSTALLATION menu, the STANDARD lamp mode is
activated by default whenever the projector is turned
on. When LAMP MODE has been set to LOW, the lamp
mode changes from STANDARD to LOW about one
minute after turn-on.
Indicator
1
Important:
• Do not cover the lens with the lens cap while the lamp is on.
Do not strip off the aluminum sheet inside the lens cap.
• The projector starts warming up when the POWER button is
pressed. During the warm-up process, images may appear
dark and no commands are accepted.
• By blinking red, the STATUS indicator indicates that the
lamp should be replaced soon. Replace the lamp when the
STATUS indicator blinks red. (See page 23 and 26.)
EN-13
Basic operation (continued)
Power-off
Volume from the speaker
Use the following procedure to turn off the projector. Do not
turn off the projector by unplugging the power cord while the
lamp is on. Unplugging while the lamp is on degrades the
lamp’s performance and causes failure in the projector.
Press the VOLUME + or -button to change the volume
from the speaker.
The volume control bar will appear on the screen.
1.
2.
3.
Press the POWER button on the control panel or the OFF
button on the remote control.
• The message "POWER OFF? YES : PRESS AGAIN"
appears on the screen.
• To cancel, press any button except the POWER button.
(Some buttons on the remote control don’t function for
cancel.)
Press the POWER button on the control panel or the OFF
button on the remote control within 10 seconds again.
• The lamp will go out and the STATUS indicator will start
blinking.
• Though the lamp goes out at this second press of the
POWER button (or OFF button), the air outlet fans continue operating for one minute to cool down the lamp.
The STATUS indicator will stop blinking.
Unplug the power cord.
• The POWER indicator will go out.
• If the power cord should be unplugged accidentally
while either the air inlet fan or the air outlet fans are
operating or the lamp is on, allow the projector to cool
down for 10 minutes with the power off. To light the
lamp again, press the POWER button (or OFF button).
If the lamp doesn’t light up immediately, repeat pressing
the POWER button (or OFF button) two or three times.
If it should still fail to light up, replace the lamp.
Important:
• When storing the projector in the provided carrying case,
the lens should face up.
AUTO POSITION button
When the image isn’t projected in the right position with COMPUTER selected as the input source, follow the procedure
below.
1.
Project a bright image such as the "Recycle Bin" window
on the full screen.
2.
If the screen saver is running, turn it off.
3.
Press the AUTO POSITION button.
• If the image is still not in the right position, adjust the
image position using the SIGNAL menu. See page 19.
VOLUME
10
• The volume control bar will disappear about 10 seconds
after the VOLUME button is released.
• The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed.
• When a high-level audio signal, such as a DVD audio signal,
is supplied to the AUDIO IN terminal, the output from the
speaker may be distorted.
AV mute
The video and audio signals are temporarily muted when the
MUTE button is pressed. To cancel muting, press the MUTE
button again.
ANAMORPHIC mode
When playing DVD discs containing data of letterboxed image,
press the 16:9 button. Exit the ANAMORPHIC mode, by pressing the 16:9 button again.
Important:
• When a letterboxed image is kept displayed for a long time
before displaying 4:3 image, the afterimages of the black
bars may appear on the 4:3 image screen. Consult your
dealer in this case.
Caution:
• After using the projector, wait one minute for the air outlet
fans to stop. Then unplug the power cord from the wall outlet.
• The lamp can’t be lit again for one minute after turned off for
safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector
again, wait until the indicator goes out, and then press the
POWER button.
• The air outlet fans rotate faster as the temperature around
the projector rises.
• When the temperature around the projector rises high, the
sign "TEMPERATURE!!" blinks red on the screen. If the
temperature stays high, the lamp will go out automatically.
Important:
• Do not display a still picture for a long time because the
afterimages may persist on the screen.
EN-14
IMAGE
CONTRAST
BRIGHTNESS
WHITE ENHANCE
COLOR TEMP.
COLOR
TINT
*1
SHARPNESS *1
GAMMA MODE
INSTALLATION
AUTO POWER ON
AUTO POWER OFF
SPLASH SCREEN
BACK COLOR
LAMP MODE
IMAGE REVERSE
FEATURE
MENU POSITION
CINEMA MODE *3
VIDEO SIGNAL
ANAMORPHIC
PASSWORD FUNCTION
LANGUAGE
RESET ALL
SIGNAL
±30
±30
±30
±30
ON , OFF
OFF, 5, 10, 15, 30, 60 min
ON , OFF
BLUE, BLACK
STANDARD, LOW
OFF, MIRROR, INVERT, MIRROR INVERT
(These items are not available when the
input source is COMPUTER.)
1 (Upper left), 2(Lower right)
AUTO , OFF
AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
ON , OFF
MENU ACCESS
OK
LOCK
UNLOCK
OK
OK
HORIZ.POSITION
VERT.POSITION
*2
FINE SYNC.
*2
TRACKING
COMPUTER INPUT *2
SET UP
*2
HOLD
USER
±30
±30
AUTO, 0 - 10
STANDARD
CONTRAST R
LOW
CONTRAST B
HIGH
BRIGHTNESS R
USER
BRIGHTNESS B
±10
±10
±5
AUTO, DYNAMIC, STANDARD, THEATER
ENGLISH
Menu operation
*2
0 - 999
*4
0 - 999
*4
0 - 31
0 - 9999
*4
RGB, YCBCR / YPBPR
OFF / 3.5% / 7.5%
ON
OFF
BEGIN
END
CLAMP POSITION
CLAMP WIDTH
ON
0 - 15
0 - 15
*4
*4
0 - 63
1 - 63
*4
*4
* 1: Not available with certain signals.
* 2: Not available when the source is a VIDEO or S-VIDEO signal.
* 3: Available only when the input signal is TV60, 480i.
* 4: Setting range differs depending on the input signals.
Basic operation
4.
Several settings can be adjusted using the menu. OFF.
Example : Auto power off time setting
1.
AUTO POWER
ON
AUTO POWER
OFF
5.
XGA60
OFF
Press the W or X button to select INSTALLATION.
opt.
XGA60
INSTALLATION
Press the ENTER button (or T button).
opt.
XGA60
Press the W or X button to adjust the auto power off time.
AUTO POWER
ON
AUTO POWER
OFF
IMAGE
3.
OFF
Press the MENU button.
opt.
2.
Press the S or T button to select AUTO POWER OFF.
6.
OFF
30 min
Exit the menu by pressing the MENU button several times.
Important:
• When the button doesn’t function, unplug the power cord
from the wall outlet. Wait about 10 minutes, plug the power
cord in, and try again.
• After selecting the items marked with , press the ENTER
button.
INSTALLATION
AUTO POWER
ON
AUTO POWER
OFF
OFF
OFF
EN-15
Menu operation (continued)
1 IMAGE
CONTRAST.................................Use to adjust the image contrast. The contrast
opt.
XGA60
becomes higher as the value increases.
IMAGE
BRIGHTNESS .............................Use to adjust the image brightness. The image
CONTRAST
0
becomes brighter as the value increases.
BRIGHTNESS
0
WHITE ENHANCE ......................Use to adjust the white level of the projected image.
Select AUTO for normal use.
WHITE ENHANCE
AUTO
STANDARD
COLOR TEMP.
COLOR TEMP.............................Use to adjust the color temperature. See page 18.
COLOR
0
COLOR........................................Use to adjust the color intensity of the image.
TINT
0
TINT.............................................Use to adjust the color balance of the image. The
SHARPNESS
0
color balance shifts to green as the value increases
and shifts to purple as the value decreases. (AvailAUTO
GAMMA MODE
able only when VIDEO or S-VIDEO is chosen as the
source.)
• When the TV50 (PAL, SECAM) signal is input, TINT can’t be adjusted.
SHARPNESS ..............................Use to adjust the image sharpness. The image becomes sharp as the value increases. (Not
available with certain signals.)
GAMMA MODE ..........................When AUTO is selected, the appropriate gamma mode is automatically selected depending on
the input signal. For normal use, select AUTO. Select DYNAMIC for computer sources. Select
STANDARD for sport scenes and video sources. Select THEATER for film sources.
2 INSTALLATION
AUTO POWER ON ......................When ON is chosen, the lamp is automatically lit
opt.
XGA60
when the power cord is plugged in the wall outlet.
Choose ON when using the projector mounted on the
INSTALLATION
AUTO POWER
ceiling.
OFF
ON
AUTO POWER
• The projector is in the stand-by mode when the
OFF
OFF
SPLASH
lamp is off. Use the remote control to turn on the
ON
SCREEN
lamp.
BACK COLOR
BLUE
AUTO POWER OFF ....................Use to set the time elapsed before the projector
STANDARD
LAMP MODE
enters the stand-by mode when there is no signal
IMAGE
OFF
REVERSE
input from the source.
SPLASH SCREEN ......................Choose ON to display the splash screen when the
power is turned on.
BACK COLOR .............................Use to select the background from among BLUE and BLACK, which will be displayed when there
is no signal input from the source.
LAMP MODE ...............................Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept low
and the projector operating noise is reduced, resulting in a longer lamp replacement interval.
• When the lamp mode is switched, the projected image may flicker. This is not a product malfunction.
• Do not change the setting of LAMP MODE frequently.
• When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW
about one minute after turn-on.
IMAGE REVERSE .......................Use to reverse the projected image. Select MIRROR for rear projection with the tabletopmounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted projector.
ON
EN-16
MENU POSITION ....................... Use to select the position of the menu on the screen,
opt.
XGA60
1.
(upper left) or 2.
(lower right).
FEATURE
CINEMA MOD............................. When AUTO is selected, the film mode will be autoMENU POSITION
1.
matically activated when a film source signal is inputted. When OFF is selected, the film mode will not be
AUTO
CINEMA MODE
?
activated.
AUTO
VIDEO SIGNAL
VIDEO SIGNAL........................... When AUTO is selected, the appropriate video format
ON
ANAMORPHIC
is automatically selected depending on the input sigPASSWORD
MENU
ACCESS
FUNCTION
nal. If the image isn’t displayed correctly, select the
AË
English
LANGUAGE
desired video format manually.
OK
RESET ALL
ANAMORPHIC............................ Select ON when playing DVD discs containing data of
widescreen images.
PASSWORD FUNCTION .............. Use to change the mode of the password lock or to enable or cancel the password lock. See
page 21 for details.
LANGUAGE ................................ Use to select the language used in the menu. (
/ English / Español / Deutsch / Français /
Italiano /
/
/
/ PORTUGUÊS).
RESET ALL................................. Use to reset the menu settings (except PASSWORD FUNCTION, and LANGUAGE ).
• CINEMA MODE can be adjusted only when a TV50, TV60, 480i, 576i signal is being displayed.
• When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of VIDEO SIGNAL depending on the input signal in such cases.
4 SIGNAL
HORIZ. POSITION...................... Use to adjust the horizontal position of the image.
opt.
VERT. POSITION ........................ Use to adjust the vertical position of the image.
SIGNAL
FINE SYNC ................................. Use to synchronize the projector with the PC input
HORIZ. POSITION
signal so that the image is not blurred.
VERT. POSITION
TRACKING.................................. Use to eliminate image noise such as wide stripes.
FINE SYNC.
COMPUTER INPUT ................... The projector adjusts its settings automatically when
TRACKING
connected to a DVD player equipped with a compoCOMPUTER
nent video output (Y, CB, CR). When the projector is
INPUT
connected with a device having an RGB terminal,
SET UP
choose RGB manually.
HOLD
SET UP ....................................... When OFF is selected, the black area becomes make
USER
lighter. When 3.5% or 7.5% is selected, the black
area becomes thicker.
HOLD ......................................... Use to adjust the image when flagging occurs near the top of the screen.
XGA60
0
0
0
0
RGB
R
RG
GB
B
7.5%
ON
OK
5 SIGNAL - USER (No need to adjust in normal use.)
CLAMP POSITION/
CLAMP WIDTH ........................... Use to correct solid white or solid black in the projected image.
USER
CLAMP
POSITION
0
CLAMP WIDTH
1
Important:
• You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is supplied.
EN-17
ENGLISH
3 FEATURE
Image adjustment
Image adjustment
Color temperature
You can adjust the image using the IMAGE menu.
1.
Select COLOR TEMP. in the IMAGE menu.
2.
Press the W or X button to select USER
3.
Press the ENTER button.
opt.
XGA60
.
IMAGE
CONTRAST
0
BRIGHTNESS
0
USER
CONTRAST R
0
CONTRAST B
0
STANDARD
BRIGHTNESS R
0
COLOR
0
BRIGHTNESS B
0
TINT
0
SHARPNESS
0
WHITE ENHANCE
COLOR TEMP.
GAMMA MODE
AUTO
AUTO
To control the white-to-black level of the image :
4.
Press the S or T button to select the desired item.
5.
Press the W or X button to adjust the selected item.
6.
Repeat steps 4 and 5 for optimum adjustment results.
7.
Exit the menu by pressing the MENU button several times.
Adjust CONTRAST in the IMAGE menu. Press the X button to
increase the contrast and the W button to reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in the IMAGE menu. Press the X button
to lighten the image and the W button to darken it.
To determine the intensity of the color :
Adjust COLOR in the IMAGE menu. Press the X button to
increase the amount of color in the image and the W button to
decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in the IMAGE menu. Press the X button to
increase the amount of green in the image and the W button to
increase the amount of red in the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in the IMAGE menu. Press the X button
to sharpen the image and the W button to soften the image.
EN-18
About color temperature
There are different kinds of white color. Color temperature
is a way to show the differences in white.
White of which temperature is low appears reddish.
When the color temperature rises, white appears bluish.
This projector adjusts this color temperature by changing
the values of contrast blue and red.
To rise the color temperature:
Increase the CONTRAST B (blue) and decrease the
CONTRAST R (red).
To reduce the color temperature:
Decrease the CONTRAST B (blue) and increase the
CONTRAST R (red).
Simple adjustment method
This projector adjusts the format of the video signal supplied
from the computer. However, sometimes images are not projected correctly owing to the type of the computer used. When
the image from the computer isn’t projected correctly, press
the AUTO POSITION button. (See page 14.) If the image isn’t
projected correctly yet, adjust the image from the computer
using the menu.
1.
Select HORIZ. POSITION in the SIGNAL menu.
2.
Press the W or X button to adjust the horizontal start position (or the left side of the image).
3.
Select TRACKING in the SIGNAL menu.
4.
Press the W or X button to adjust the horizontal end position (or the right edge of the image).
5.
Repeat steps 1 to 4 for optimum adjustment results.
6.
Select VERT. POSITION in the SIGNAL menu.
7.
Press the W or X button to adjust the vertical start position
(or the upper edge of the image).
opt.
XGA60
SIGNAL
HORIZ. POSITION
R
RG
GB
B
0
VERT. POSITION
0
FINE SYNC.
0
TRACKING
0
COMPUTER
INPUT
RGB
SET UP
7.5%
HOLD
ON
USER
OK
To move the image horizontally :
Adjust HORIZ. POSITION in the SIGNAL menu. Press the X
button to move the image to the left. Press the W button to
move the image to the right.
To move the image vertically :
Adjust VERT. POSITION in the SIGNAL menu. Press the X
button to move the image upward. Press the W button to move
the image downward.
When the image flickers or the image is out of focus :
Adjust FINE SYNC. in the SIGNAL menu.
When the top part of the image flags :
Change the setting of HOLD in the SIGNAL menu. Select ON
, press the ENTER button, and adjust BEGIN or END to
minimize the flagging.
USER
CLAMP
POSITION
0
CLAMP WIDTH
1
When wide strips appear :
Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL USER menu.
Important:
Do not change any of the settings in the SIGNAL-USER menu
for normal use.
EN-19
ENGLISH
Adjustment of the image from the computer
Advanced feature
Still
To stop the motion in the image temporarily (or to display a still
image):
Press the STILL button on the remote control.
• The image will freeze temporarily.
To resume the motion in the image:
Press the STILL button on the remote control again.
Important:
• Do not display a still picture for a long time because the
afterimages may persist on the screen.
Page-up and page-down
You can control the computer to page-up and page-down the
presentation data using the remote control. Switch the pages
using the PAGE UP or DOWN button on the remote control.
Connection
To control the computer using the remote control, connect the
projector with the computer as shown below.
USB
USB 4-pin
(type B)
to USB port
USB cable
(option)
USB 4-pin
(type A)
• Only the computers equipped with a USB port are supported.
• Wait for the lamp to light up before connecting the USB
cable.
EN-20
To cancel the password function:
This projector is equipped with the password function that is
designed for prevention of wrong operation by children and
restriction on operation by other than specified users.
MENU ACCESS ............All the buttons except for the POWER
button on the projector are disabled. (The buttons on the
remote control are enabled.) You can use this mode as a
measure of prevention of wrong operation by children and
restriction on operation by other than specified users.
1.
Display the FEATURE menu.
2.
Press the S or T button to select PASSWORD FUNCTION.
3.
Press the ENTER button.
• The screen for canceling the password function will
appear.
opt.
To enable the password function:
1.
Display the FEATURE menu.
2.
Press the S or T button to select PASSWORD FUNCTION.
3.
Press the ENTER button.
• The screen for setting the password function will
appear.
opt.
XGA60
MENU ACCESS
4.
LOCK
OK
UNLOCK
OK
Press the ENTER button.
• The screen for entering the password will appear.
PASSWORD
OK
XGA60
CANCEL
MENU ACCESS
LOCK
OK
UNLOCK
OK
• When the password has already been set, the mode
won’t be changed. In such cases, press the ENTER
button to cancel the password function and try again.
4.
Press the ENTER button.
• The screen for entering a password will appear.
PASSWORD
CONFIRM
OK
CANCEL
5.
Press the S or T button to select a number from 0 to 9.
6.
Press the X button.
• You can set the next digit.
7.
Repeat steps 5 and 6 to set a four-digit password.
8.
Enter the password again for confirmation using the same
steps.
9.
Select OK, and press the ENTER button.
• If the entered passwords don’t match, an error message will appear.
• To cancel the procedure, select CANCEL, and press
the ENTER button.
• You can cancel the procedure by pressing the MENU
button alternatively.
5.
Press the S or T button to select a number from 0. to 9.
6.
Press the X button.
• You can set the next digit.
7.
Repeat steps 5 and 6 to enter the four-digit password.
8.
Press the X button, select OK, and press the ENTER button.
• If you enter a wrong password, an error message will
appear.
• To cancel the procedure, press the X button, select
CANCEL, and press the ENTER button.
• You can cancel the procedure by pressing the MENU
button alternatively.
Important:
• If you forget your password, keep pressing the MENU and
ENTER buttons on the control panel at the some time about
three seconds to cancel the password function.
EN-21
ENGLISH
Password function
Lamp replacement
When the lamp no longer functions, replace it with a new one.
9.
Caution:
• Do not remove the lamp immediately after using the projector. You may get burned because the lamp very hot after
use.
• Before replacing the lamp, press the POWER button to turn
off the lamp and wait for two minutes for lamp to cool down.
Unplug the power cord from wall outlet and wait one hour
for the lamp to cool down completely.
• Do not remove the lamp except for replacement. Careless
handling can cause injury or fire.
• Do not touch the lamp directly. It may break and cause
injury or burn.
• Be sure not to drop the lamp lid screw into the projector.
Also be sure not to put metal or any flammable objects
inside because it may cause fire or electric shock. If any
objects should fall inside, unplug and contact your dealer.
• Install the lamp securely to prevent failure and fire.
• If the lamp should break, small glass fragments may fall out
through the grilles and some may remain inside of the projector or the lamp box. When taking the lamp box out, be
sure to turn over the projector and hold the handle of the
lamp box to avoid injury due to the glass fragments.
• If the lamp should break, never shake the lamp box or hold
it in front of your face after removing it. The lass fragments
may fall out and cause injury to your eyes.
• When placing the projector upside down to replace the lamp
or conduct maintenance, ensure that the projector is
securely placed before working with it.
1.
Reverse the projector gently.
2.
Loosen the screws (a) using a Phillips screwdriver (+), and remove
the lamp cover (b).
3.
Loosen the screws (c) using a Phillips screwdriver (+).
4.
Pull up the handle.
5.
Pull out the lamp box by the handle
while holding the projector.
• Pull the lamp box out of the projector slowly. If it is pulled out
quickly, the lamp may break
scattering glass fragments.
• Do not spill liquid on the
removed lamp box or do not
place it near any flammable
object or where children can
reach to prevent injury or fire.
6.
7.
8.
Load a new lamp box securely into
the projector in the right orientation.
Put the handle back to the original
position.
• Make sure that the handle is
locked.
Tighten up the screws (c) using a
Phillips screwdriver (+).
(a)
Tighten up the screw (a) using a
Phillips screwdriver (+) to secure
the lamp cover.
(a)
Reset of the lamp operation time
Plug in the power cord, turn on the
lamp, and reset the lamp operation time
by keep pressing the W, X, and
POWER buttons on the control panel at
the same time about three seconds.
(b)
Important:
• Unless these three buttons are pressed at the same time,
the lamp operation time isn’t reset.
• Make sure that the STATUS indicator is lit twice and the
lamp operation time is reset successfully.
• The projector doesn’t turn on if the lamp cover isn’t attached
securely.
• Be sure to reset the lamp operation time whenever you
replace the lamp.
• Do not reset the lamp operation time unless you replace the
lamp.
Caution:
• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
• Contact your dealer for a new lamp.
Interval of lamp replacement
When the lamp shutdown notice is issued, the lamp replacement is recommended even if the lamp is lit normally.
Decrease in luminescence and/or color brightness indicates
that the lamp needs to be replaced. When the lamp operation
time exceeds the time elapsed until the lamp shutdown notice*1
is issued, the indicator will blink alternately green and red while
the lamp is lit (while the lamp is not lit, the indicator will blink
red only) and the lamp replacement message will appear on
the screen for one minute every time the lamp is turned on.
When the lamp operation time exceeds the time elapsed until
the lamp shutdown warning*2 is issued, the replacement message (LAMP EXCHANGE) will appear on the screen for one
minute at fixed intervals*4 thereafter.
When the lamp operation time exceeds the time
elapsed until the lamp shutdown*3, the projector automatically shuts off and can’t be used until the lamp is
replaced and the lamp operation time is reset.
(b)
XD205U/SD205U
(c)
*1
2250 Hours
2850 Hours
*3
3000 Hours*5
*2
The times above are when LAMP MODE of the INSTALLATION menu is set to
LOW. When it is set to STANDARD, this duration will be shortened.
*4
*5
These intervals vary depending on the lamp mode setting.
When LAMP MODE is set to STANDARD, the time
elapsed until the lamp shutdown will be shortened to 2000
hours.
Caution:
• This projector uses a lamp that contains mercury. Disposal
of the lamp or the projector with the lamp may be regulated
due to environmental considerations. For disposal or recycling information, please contact your local authorities or the
Electronic Industries Alliance: www.eiae.org. (For US only).
EN-22
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before
contacting your dealer.
Images aren’t projected on the screen.
Problem
Cause and solution
•
Check the states of the indicators.
POWER STATUS
Off
Off
Solution
Connect the power cord to the projector.
Plug the power cord into a wall outlet.
If any objects are blocking the air inlet or outlet grille, remove them and carry out
the following.
Off
1.
2.
3.
4.
Unplug the power cord from the wall outlet.
Make sure that the projector has cooled off.
Plug the power cor d into the wall outlet.
Press the POWER button.
If any objects are blocking the air inlet or outlet grille, remove them.
Don't expose the air outlet grilles to hot air emitted from a heating appliance.
Steady red
Power isn’t turned on.
Blinking
orange
After the STATUS indicator stops blinking, press the POWER button.
Blinking
green
If you unplug the power cord while the fan is rotating, the lamp may not turn on about
one minute when you plug the power cord next time.
The lamp can't turn on again for one minute after it goes out.
Press the POWER button several times.
Replace the lamp. (The lamp is at the end of its life.)
Steady red
Off
Blinking red
/ green
Steady
or
Attach the lamp cover on the bottom.
Unplug the power cord from the wall outlet and contact your dealer.
Blinking
•
•
•
•
•
Images aren’t projected on the screen.
•
•
•
•
Images suddenly disappear.
•
•
•
"NO SIGNAL" is displayed.
•
•
•
•
Cancel the AV mute by pressing the MUTE button.
Remove the lens cap.
The lamp sometimes takes about one minute to light up.
On rare occasion, the lamp fails to light up. In such cases, wait a few minutes and try to light the
lamp again.
If the projector was turned off before the lamp cooled down completely, the fans may start rotating and the POWER button may not function when you plug the power cord into the wall outlet
next time. Wait for the fans to stop and press the POWER button to turn on the lamp again.
Check that the lamp cover are closed.
Check that the cable connected to the external device isn’t broken.
When an extension cord is being used, replace it with the supplied cable and check whether
images are projected correctly. If images are projected correctly, use an RGB signal amplifier
along with the extension cord.
The air inlet or outlet grille may be blocked. (In such cases, the STATUS indicator blinks
orange.)
J Remove the objects blocking the air inlet or outlet grille and carry out the following.
1. Wait for the air inlet or outlet fan to stop (or wait for the STATUS indicator to go out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
When the STATUS indicator is blinking red, it is indicating that the lamp should be replaced.
Replace the lamp in this case.
Turn on the power of the connected device, or check whether there is something wrong with the
connected device.
Check whether the external device outputs signals. (Check this especially when the external
device is a notebook computer.)
Check that the cable connected to the external device isn’t defective.
Check that the projector is connected to the external device using the correct terminals.
Check that the connected device is correctly selected as the input source.
When an extension cord is being used, replace it with the supplied cable and check whether
images are projected correctly. If images are projected correctly, use an RGB signal amplifier
along with the extension cord.
EN-23
ENGLISH
Troubleshooting
Troubleshooting (continued)
Images aren’t projected correctly.
Problem
Cause and solution
•
•
•
•
Check that the cable connected to the external device isn’t intermittent.
Connect the cable’s plug with the external device’s connector firmly.
Press the AUTO POSITION button.
Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See
page 19.)
Projected images are distorted.
•
Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.)
Projected images are dark.
•
•
•
Adjust BRIGHTNESS in the IMAGE menu. (See page 18.)
Replace the lamp. (See page 22.)
Remove the lens cap.
Projected images are blurred.
•
•
•
•
•
•
Adjust the focus. (See page 13.)
Clean the lens.
Remove the lens cap.
Press the W or X button on the remote control to eliminate flicker.
Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 18.)
Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.)
•
This symptom is normal for a DLP projector and is not a malfunction. (A very small number of
pixels may stay lit or out, but such symptom is not a malfunction. Pixels of 99.99% or more are
effective.)
Rainbow blur appears in projected images.
•
This is due to color breaking noise that occurs in a DLP system and is not a malfunction.
Fine streak pattern appears in projected
images.
•
It occurs because of interference with the screen and isn’t a product malfunction. Change the
screen or readjust the focus of the projector.
•
•
•
Connect the cable’s plug with the external device’s connector firmly.
Keep the projector away from equipment generating interfering radio waves.
When the keystone adjustment is carried out, the image may not be displayed correctly
because of the type of input signal. This isn’t a product malfunction. In this case, readjust the
keystone so that the amount of keystone correction is as small as possible.
Tint in projected images is incorrect.
•
•
Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 17.)
Check that the cable connected to the external device isn’t broken.
Only the motion areas in the images supplied
from the computer aren’t displayed.
•
This is caused by the computer being used. Contact the manufacturer of your computer.
•
Match the output resolution of your computer with the resolution of the projector. For the
method to change the output resolution of the computer, contact the manufacturer of your computer. (See page 29.)
Some images and texts appear obscured during the keystone adjustment. In such cases, use
the projector without applying the keystone adjustment. (See page 12.)
Projected images are shaking.
Projected images are displaced.
White dots are seen on projected images.
Black dots are seen on projected images.
Projected images (and/or audio) appear wavy
and distorted.
Projected images are obscured.
•
EN-24
Problem
Hot air is emitted from the air outlet grilles.
No audio is output.
Cause and solution
•
This air comes out as a result of cooling the inside of the projector. This isn’t a product malfunction.
•
Check that the volume isn’t set to low.
•
The microcomputers inside the projector may be wrongly operating because of noise.
J Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.
•
This indication appears when the ambient temperature rises high. When the ambient temperature stays high, the lamp goes out.
J Eliminate any causes of the rise in the ambient temperature.
This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked,
the lamp goes out.
J Remove the objects blocking the air inlet or outlet grille.
The menu can’t be used.
"TEMPERATURE!!" is displayed.
The
mark appears.
The remote control doesn’t function easily or
at all.
The buttons on the control panel (except for
the POWER button) don’t function.
Abnormal sound is heard.
•
•
This mark appears when ineffective operation is carried out. This isn’t a product malfunction.
•
•
Check that the battery is loaded in the remote control or the battery isn’t weak. (See page 8.)
Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See
page 8.)
Use the remote control within its operation range. (See page 8.)
Use the remote control at least 10 cm away from the projector.
•
•
•
The password function is working.
J Cancel the password lock. (See page 21.)
•
Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symptom is not a malfunction.
When the problems below occur after the lamp is replaced, check the following.
Problem
Cause and solution
The power isn’t turned on.
•
•
Attach the lamp cover on the bottom correctly.
Reset the lamp operation time. (See page 22.)
The STATUS indicator blinks.
•
Reset the lamp operation time. (See page 22.)
Maintenance
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened
with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only
recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
EN-25
ENGLISH
Others
Indicators
This projector has two indicators, each of which shows the operation condition of the projector.
The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer.
STATUS indicator
POWER indicator
Normal condition
POWER
STATUS
Steady red
Off
Steady green
Blinking green
Steady green
Steady green
CONDITION
NOTE
Stand-by
Lamp stand-by (about 1 minute)
The POWER button cannot be used to switch
between on and off.
The power is on. (Normal condition)
Abnormal condition
POWER
STATUS
Steady green
or
CONDITION
Blinking orange
Abnormal temperature
• The ventilation grilles is clogged with dust or dirt.
• The room temperature is high.
Blinking green
The protection circuit is working or the lamp is in an
abnormal condition.
POSSIBLE SOLUTION
•
•
Clean the ventilation grilles.
Relocate the projector to a cooler place.
•
Wait until the STATUS indicator goes out,
then press the POWER button.
If the above solution is not effective,
replace the lamp.
Steady red
Steady red
Steady green
The lamp operation time exceeds the time elapsed until
the lamp shutdown notice while the power is on. (See
Blinking green/red page 22.)
Steady red
Blinking red
The lamp operation time exceeds the time elapsed until
the lamp shutdown notice while the power is off. (See
page 22.)
Steady red
Steady red
The lamp operation time exceeds the time elapsed until
the lamp shutdown. (See page 22.)
Blinking green/red
Off
Steady
or
Blinking green/red
Blinking
EN-26
•
Replace the lamp.
Change with a new lamp if this problem
recurs.
The lamp cover isn’t closed.
Close the cover correctly.
Abnormal.
Contact your dealer.
ENGLISH
Specifications
Type
DLP™ DATA projector
Model
XD205U/SD205U
Rated power supply
100 - 240 V AC, 50 / 60 Hz
Rated input
2.9 A (XD205U/SD205U)
Display Technology
0.55-inch Single chip Digital Micromirror Device (DMD) with R,G,B,W color wheel
Pixels 1024 x 768 = 786432 pixels (XD205U)
Pixels 800 x 600 = 480000 pixels (SD205U)
Colors
16770000 colors
Projection lens
F 2.4- 2.6 f = 18 - 21.6 mm
Light source lamp
205 W (XD205U/SD205U)
Picture size
40 - 300 inch (aspect ratio 4:3)
PC compatibility
Resolution:640x400 (Expand) - 1024x768 (Real) - 1280x1024 (Compress) (XD205U)
Resolution:640x400 (Expand) - 800x600 (Real) - 1024x768 (Compress) (SD205U)
Sync on Green available
Video compatibility
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p)
Speaker
2 W Mono, Round type ø4.5 cm x 1
S-video input
Luminance signal: 1.0 Vp-p 75 Ω (negative sync.)
Chroma signal: 0.286 Vp-p 75 Ω (burst signal)
Video input
1.0 Vp-p 75 Ω (negative sync.)
Audio input
350 mVrms, 10 kΩ or more
Analog RGB input
RGB: 0.7 Vp-p 75 Ω (negative sync.)
YPBPR/YCBCR : Y:1.0 Vp-p (negative sync.)
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
Control connector
USB terminal (for Page Up/Down)
Outside dimensions
261 x 102 x 218 mm (width x height x depth)
Weight
Approx. 2.4 kg
Length of power cord
114 inch (2.9 m)
Temperature, humidity
(performance guaranteed)
+41ºF (+5ºC) - +95ºF (+35ºC), 30 - 90%
PBPR/CBCR:0.7 Vp-p
• The specifications and outside appearance of the projector are subject to change without prior notice.
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington
Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : +1- (650) 572-2700
Fax : +1- (650) 572-9675
EN-27
Specifications (continued)
Connectors
COMPUTER IN/OUT (Mini D-SUB 15-pin)
11
15
10
6
1
IN
5
OUT
pin No.
Spec.
pin No.
Spec.
1
R(RED)/CR
1
R(RED)/CR
2
G(GREEN)/Y
2
G(GREEN)/Y
3
B(BLUE)/CB
3
B(BLUE)/CB
4
GND
4
-
5
GND
5
GND
6
GND
6
GND
7
GND
7
GND
8
GND
8
GND
9
DDC5V
9
-
10
GND
10
GND
11
GND
11
-
12
DDC Data
12
-
13
HD/CS
13
HD/CS
14
VD
14
VD
15
DDC Clock
15
-
218
Dimensional drawings (unit : mm)
102
261
What’s included in the box
AC power cord
for US
for EU
for UK
1 RGB cable for PC
1 VIDEO cable
246D034-10
246D035-10
246D036-10 (UK only)
246D037-10
246D039-10
Replacement part
(Option / Not included in the box)
Spare lamp (for XD205U/SD205U)
EN-28
499B045-20
(VLT-XD205LP)
1
1
1
1
1
2
Remote control
Quick Start up
Safety manual
CD-ROM
Carrying case
Battery
290P131-20
857D082-10
871D472-10
919D273-10
772P046-10
–
resolution
(H x V)
horizontal
frequency (kHz)
vertical
frequency (Hz)
XD205U
(H x V)
SD205U
(H x V)
TV60, 480i(525i)
-
15.73
59.94
1024 x 768
800 x 600
TV50, 576i(625i)
-
15.63
50.00
1024 x 768
800 x 600
1080i 60 (1125i 60)
-
33.75
60.00
1024 x 576
800 x 450
1080i 50 (1125i 50)
-
28.13
50.00
1024 x 576
800 x 450
480p (525p)
-
31.47
59.94
1024 x 768
800 x 600
576p (625p)
-
31.25
50.00
1024 x 768
800 x 600
720p 60 (750p 60)
-
45.00
60.00
1024 x 576
800 x 450
720p 50 (750p 50)
-
37.50
50.00
1024 x 576
800 x 450
Signal mode
PC98
640 x 400
24.82
56.42
1024 x 640
800 x 500
CGA84
640 x 400
37.86
84.13
1024 x 640
800 x 500
CGA85
640 x 400
37.86
85.08
1024 x 640
800 x 500
VGA60
640 x 480
31.47
59.94
1024 x 768
800 x 600
VGA72
640 x 480
37.86
72.81
1024 x 768
800 x 600
VGA75
640 x 480
37.50
75.00
1024 x 768
800 x 600
VGA85
640 x 480
43.27
85.01
1024 x 768
800 x 600
SVGA56
800 x 600
35.16
56.25
1024 x 768
800 x 600
SVGA60
800 x 600
37.88
60.32
1024 x 768
800 x 600
SVGA72
800 x 600
48.08
72.19
1024 x 768
800 x 600
SVGA75
800 x 600
46.88
75.00
1024 x 768
800 x 600
SVGA85
800 x 600
53.67
85.06
1024 x 768
800 x 600
XGA60
1024 x 768
48.36
60.00
1024 x 768
800 x 600
XGA70
1024 x 768
56.48
70.07
1024 x 768
800 x 600
XGA75
1024 x 768
60.02
75.03
1024 x 768
800 x 600
XGA85
1024 x 768
68.68
85.00
1024 x 768
800 x 600
SXGA70a
1152 x 864
63.85
70.01
1024 x 768
-
SXGA75a
1152 x 864
67.50
75.00
1024 x 768
-
SXGA60b
1280 x 960
60.00
60.00
1024 x 768
-
SXGA60
1280 x 1024
63.98
60.02
960 x 768
-
MAC13
640 x 480
35.00
66.67
1024 x 768
800 x 600
MAC16
832 x 624
49.72
74.55
1024 x 768
800 x 600
MAC19
1024 x 768
60.24
75.02
1016 x 768
800 x 600
MAC21
1152 x 870
68.59
74.96
1024 x 768
-
HP75
1024 x 768
62.94
74.92
1024 x 768
800 x 600
SUN66a
1152 x 900
61.85
66.00
984 x 768
-
SUN76a
1152 x 900
71.81
76.64
984 x 768
-
Important:
• Some computers aren’t compatible with the projector.
• The projector’s maximum resolution is 1024 x 768 pixels
(800 x 600 pixels for SD205U). It may not display images of
higher resolutions than 1024 x 768 (or 800 x 600) correctly.
• Images with SYNC on G (Green) signal may jitter.
• Images with SYNC on G (Green) signal may be tinged with
green.
• If the resolution and frequency of your computer aren’t
shown on the table, find the compatible resolution and frequency by changing the resolution of your computer.
ENGLISH
Specification of RGB signals in each computer mode of the projector
• Set COMPUTER INPUT in the SIGNAL menu to RGB when
inputting the HDTV signal as RGB signal.
• TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the VIDEO or SVIDEO signal, the signal mode is indicated as TV60 or
TV50. When they are supplied to the COMPONENT terminal, the signal mode is indicated as 480i or 576i.
EN-29
MITSUBISHI Projector Contact Information
North America
Asia
MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2,
Canada
Sales
Phone
:+1-(905) 475-7728
Fax
:+1-(905) 475-7958
E-mail
:projectors@mitsubishielectric.ca
Technical
Phone
:+1-(905) 475-7728
Fax
:+1-(905) 475-7958
Customer Care
E-mail
:support@mitsubishielectric.ca
MITSUBISHI ELECTRIC RYODEN AIR-CONDITIONING &
VISUAL INFORMATION SYSTEMS (HONGKONG) LTD.
• Hong Kong Office
Units 5-10, 20/F., Ever Gain Plaza, Tower One 88 Container Port Road, Kwai
Chung, New Territories,Hong Kong.
Technical Support
Phone
:+852 2510 0777
Fax
:+852 2510 0463
• Beijing Office
9/F, Office Tower 1, Henderson Centre, 18 Jianguomennei Dajie, Dongcheng District, Beijing, 100005, China
Sales & Technical Support
Phone
:+86 (10) 6518 2930
Fax
:+86 (10) 6518 2530
• Shanghai Office
10/F, Shanghai Square Office Tower, 138 Huai Hai Zhong Road, Lu Wan District,
Shanghai, 200021, China
Sales & Technical Support
Phone
:+86 (21) 6327 2228
Fax
:+86 (21) 6327 4918
• Shenzhen Office
Unit 01-04, 13/F, Building A, Tian An International Building, Renmin Road South,
Shenzhen, 518005, China
Sales & Technical Support
Phone
:+86 (755) 518 6386
Fax
:+86 (755) 218 4775
• Chengdu Office
Block B-1, 23/F., Chuan Xin Mansion, 18 Section 2, Renmin Road South, Chengdu,
610016, China
Sales & Technical Support
Phone
:+86 (28) 619 9730
Fax
:+86 (28) 619 9801
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com/
Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Phone
Main Line
:+1-(949) 465-6000
Technical
:+1-(888) 307-0309
Product Information :+1-(888) 307-0312
Technical Support
E-mail
:tsupport@mdea.mea.com
Europe
MEU-FRA (Mitsubishi Electric Europe B.V French Branch)
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France
Sales
Phone
:+33 (0)1 55-68-55-07
Fax
:+33 (0)1 55-68-57-31
Technical
Phone
:+33 (0)1 41-02-83-24
Fax
:+33 (0)1 49-01-07-23
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales
Phone
:+353-(0)1- 4198844
Fax
:+353-(0)1-4564422
Technical
Phone
:+353-(0)1-4198807
Fax
:+353-(0)1-4198895
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch)
Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2, Via Paracelso 12, 20041
Agrate Brianza, Italy
Sales
Phone
:+39-(0)39-60531
Fax
:+39-(0)39-6053214
E-mail
:info.projector@it.mee.com
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch)
http://www.mitsubishi.nl/LCD/ProdFrame.html
Nijverheidsweg 23a, 3641 RP Mijdrecht, The Netherlands
Sales
Phone
:+31-297-282461
Fax
:+31-297-283936
E-mail
:info.lcd@nl.mee.com
Technical
Phone
:+31-297-282461
Fax
:+31-297-283936
E-mail
:info.lcd@nl.mee.com
MEU (MITSUBISHI ELECTRIC EUROPE B.V.)
http://www.mitsubishi-projector.ru/
Moscow Representative Office, 12/1 Goncharnaya St. 109240, Moscow, Russia
Sales
Phone
:+7 (095) 915 8602
Fax
:+7 (095) 915 8603
MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08190 Sant Cugat del Valles, Barcelona, Spain
Sales
Phone
:+34-93.565.31.54
Fax
:+34-93.589.43.88
E-mail
:mitsubishi.profesional@sp.mee.com
Technical
Phone
:+34-93.586.27.51
Fax
:+34-93.699.74.45
E-mail
:mitsubishi.profesional@sp.mee.com
MEAP (Mitsubishi Electric Asia Pte Ltd)
http://www.mitsubishielectric.com.sg
307 Alexandra Road, Mitsubishi Electric Building, 289245,Singapore
Main Line
Phone
:+65 6 473 2308
Fax
:+65 6 475 9503
Sales & Technical Support
E-mail
:peripherals@asia.meap.com
AMS (Antah Melco Sales & Services Sdn Bhd (A Joint-Venture Company of Mitsubishi
Electric Corporation))
http://www.antahmelco.com.
my 6, Jalan 13/6, Petaling Jaya, Selangor Darul Ehsan, Malaysia
Main Line
Phone
:+603-7955 2088
Fax
:+603-7956 3950
:+603-7958 2576
Technical Support
Phone
:+603-7955 2088
E-mail
:anmelco@po.jaring.my
Product Information
Phone
:+603-7955 2088
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.)
http://www.mitsubishi-electric.com.
tw 9th Floor., 90 Sec. 6, Chung Shan N. Rd., Taipei, Taiwan
Sales Support
Phone
: +886 (0) 2 2832 8255
Fax
: +886 (0) 2 2833 9813
KYW (Kang Yong Watana Co., Ltd.)
http://www.mitsubishi-kyw.in.th
28 Krungthep Kreetha Road, Huamark Bangkapi, Bangkok, 10240, Thailand
Sales Support
Phone
:+66 (2) 731 6901
Fax
:+66 (2) 379 4763
STC (Setsuyo Astec Corp. Seoul Branch)
Dongseo Game Channel Bldg, 660-11, Deungchon-dong, Kangseo-ku, Seoul, Korea
Main Line
Phone
:+82 (0) 2 3665 4964
Fax
:+82 (0) 2 3665 4965
Oceania
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch)
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden
Sales
Phone
:+46-(0)8-6251070
Fax
:+46-(0)8-6251036
Technical
Phone
:+46-(0)8-6251052
Fax
:+46-(0)8-6251036
ME-AUST (Mitsubishi Electric Australia)
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia
Sales
Phone
:+(612)9684-7777
Fax
:+(612)9898-0484
E-mail
:ped@meaust.meap.com
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane, Hatfield, Hertfordshire, AL10
8XB
Sales
Phone
:+44 (1707) 278684
Fax
:+44 (1707) 278541
E-mail
:projector.info@meuk.mee.com
Technical
Phone
:+44 (870) 606 5008
Fax
:+44 (1506) 431927
E-mail
:projector.info@meuk.mee.com
BDT (Black Diamond Technologies Ltd.)
(Warranty Registration)
http://www.bdt.co.nz/projectors/warranty.asp
1 Parliament St, Lower Hutt, Wellington, New Zealand
Sales
Phone
:+64-(0)4-560-9100
Fax
:+64-(0)4-560-9133
E-mail
:help@bdt.co.nz
Technical
Phone
:+64-(0)4-560-9100
Fax
:+64-(0)4-560-9133
Russia (Mitsubishi Electric Europe B.V Moscow Representative Office)
52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation
Sales
Phone
:+7 (095) 721 2070
Fax
:+7 (095) 721 2071
Technical
Phone
:+7 (095) 721 2070
Fax
:+7 (095) 721 2071
Manufactured by Mitsubishi Electric Corporation
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
MITSUBISHI ELECTRIC CORPORATION