Miele T 250 C Operating instructions

Operating instructions
for condenser tumble dryer
T 250 C
To avoid the risk of accidents or
damage to the machine it is
essential to read these operating instructions
before it is installed or used for the first time.
G
M.-Nr. 05 993 030
Contents
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electronic system lock and programmable functions. . . . . . . . . . . . . . . . . . . . . 9
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
A Prepare the laundry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
B Load the drum and switch on the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
C Select a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
D Select any additional option(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Anti-crease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Low temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Buzzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
E Start the programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F At the end of a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Additional notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Interrupting a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
To cancel a programme and select a different programme . . . . . . . . . . . . . . . 18
Adding or removing items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electronic system lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Emptying the condensed
water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning them with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2
Contents
Cleaning the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Removing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Checking the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Check and fault indicator lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
To change the interior drum
lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Room in which the dryer is located . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 35
Building under a continous worktop / in a row of kitchen units . . . . . . . . . . . . 35
Replacing the lid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Aligning the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Washer - dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Before moving the machine again (e.g. when moving house) . . . . . . . . . . . . . 36
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Pulling out the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connection to a sink drain outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
If you no longer wish to use an external condensed water outlet: . . . . . . . . . . 38
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Increased drying level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Memory function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3
Warning and Safety instructions
To avoid the risk of accidents and
damage to the machine please read
these instructions carefully before
using it for the first time. They
contain important information on its
safety, use and maintainence.
Keep these operating instructions in
a safe place and ensure that new
users are familiar with the content.
Pass them on to any future owner of
the machine.
Correct use
The tumble dryer is only intended
for drying fabrics which have been
washed in a water solution, marked on
the manufacturer's wash care label as
being suitable for tumble drying.
"Dry Cleaning Kits" for freshening up
garments in a tumble dryer are
increasingly available on the market. If
using, do so at your own risk and follow
the instructions provided on the
packaging.
Any other applications may be
dangerous. The manufacturer is not
liable for damage resulting from
improper use or operation.
This machine is not a toy! To avoid
the risk of injury, do not allow
children to play on or near it, or to
play with the controls. Supervise its
use by the elderly or infirm.
Technical safety
Before setting up the machine
check it for any externally visible
damage. Do not install or use a
damaged machine.
4
Before connecting the machine,
ensure that the connection data on
the data plate (fusing, voltage and
frequency) matches the mains
electricity supply. If in any doubt,
consult a qualified electrician.
The electrical safety of this
machine can only be guaranteed
when continuity is complete between
the machine and an effective earthing
system which complies with local and
national regulations. It is most important
that this basic safety requirement is
regularly tested, and where there is any
doubt the household wiring system
should be inspected by a qualified
electrician. The manufacturer cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
Do not connect the machine to the
mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
machine (e.g. danger or overheating).
The machine is built in accordance
with current safety requirements.
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the manufacturer cannot accept
liability. Repairs should only be
undertaken by a Miele approved
technician.
Ensure current is not supplied to the
machine while maintenance or repair
work is being carried out.
Faulty components must only be
exchanged for Miele original spare
parts. Only when these parts are fitted
can the safety standards of the
machine be guaranteed.
Warning and Safety instructions
If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
In the event of a fault or for
cleaning purposes, the machine is
only completely isolated from the
electiricty supply when:
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn.
Operation
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans, aircraft
etc. However it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.
If the water is drained externally
through the drain hose instead of
being collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.
Condensed water is not drinking
water. It can cause health
problems in both people and animals.
Always keep the area around the
machine free of dust and fluff. Dust
drawn into the machine can, over time,
cause blockages in the condenser unit.
The dryer must not be used without
the fluff filters in place or if the fluff
filters are damaged in any way.
The fluff filters must be thoroughly
dried after cleaning. If they are still
damp or wet when replaced there is a
risk of faults occurring when the
machine is used.
The dryer must not be used without
the condenser unit in place.
Do not install the machine in a
room where the temperature may
drop down to or below freezing. At very
cold temperatures the machine may be
difficult to start.
There is a risk of damage if the
5
Warning and Safety instructions
Always close the door after use.
This way you will avoid the danger
of:
– children climbing onto or into the
dryer or hiding things in it.
– pets or other small animals climbing
into it.
Do not let anyone sit or lean on the
door, as this can cause the
machine to tip up.
There is danger of fire with fabrics
which:
– contain a large proportion of rubber,
foam rubber or rubber like materials.
– have been treated with inflammable
cleaning agents.
– have been splashed with hair
lacquer, hair spray, nail varnish
remover or similar substances.
– which contain padding or fillings
(e.g. pillows, jackets). If these were
damaged the filling could leak out
with the risk of igniting in the dryer.
– are soiled with oil or grease.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not
be covered by the machine
guarantee.
6
Using accessories
Accessory parts may only be fitted
when expressly approved by Miele.
If other parts are used, guarantee,
performance and product liability
claims may be invalidated.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old machine
Old machines contain materials which
can be reclaimed or recycled. Please
contact your dealer, your local waste
collection centre or scrap merchant
about potential recycling schemes.
Energy saving tips
^ Make sure that your laundry is
thoroughly spun before drying.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
^ Load according to the optimum
amount of laundry recommended for
the programme being used (see
Programme chart).
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
^ To save energy and time:
– Make sure the room in which the
dryer is located is well ventilated.
– Make sure the fluff filters are clean
before using the dryer.
Ensure that the machine presents no
danger to children while being stored
for disposal.
Before throwing an old machine
away unplug it and render the plug
useless. Cut off the cable directly
behind the machine to prevent misuse.
This should be done by a competent
person.
7
Description of the appliance
Control panel
a START button
Press the START button to start a
programme.
The Start indicator lamp will flash as
soon as a programme can be
started. It lights up constantly once
the programme has started.
b Buttons for activating and
deactivating additional options
Indicator lamp lit up = activated
not lit up = deactivated
c Programme selector
The programme selector can be
turned clockwise or anti-clockwise.
To save energy, the light ring around
the programme selector goes out a
few minutes after the dryer has been
switched on, if no programme is
selected or if a programme is not
started. The light ring also goes out a
few minutes after a programme has
finished.
8
d Progamme sequence indicator
lamps
show the drying stage reached;
and Check lamps:
See "Problem solving guide" for
information on the check lamps.
e I-On/0-Off button
To switch the appliance on or off or to
interrupt a programme.
f Door Button
to open the door / to cancel a
programme.
Pressing this button will open the
door even when the appliance is
switched off at the mains.
If the appliance is switched on at the
mains and the door is opened the
drum lighting will come on. It will go
out a few minutes later to save
energy.
Description of the appliance
Future updates (PC)
The indicator lamp marked PC on the
fascia panel is the interface used by
the Miele service technicians for
updating the machine’s programme
data.
Electronic system lock and
programmable functions
The following can be programmed into
your machine using the programme
selector in combination with the
buttons.
Electronic system lock
Prevents the machine being operated
by others.
Programmable functions
Programmable functions enable the
machine to be adapted to suit personal
requirements.
See the relevant section for detailed
instructions.
9
Notes on laundry care
Wash care labels
Before drying check the drying
symbol on the wash care label.
Significance of symbols:
q Dry at normal temperature
r Dry at low temperature
s Do not tumble dry
If no symbol is featured, dry at your
own risk applying the following
principles:
Cotton and minimum iron items should
be dried using the appropriate
programme for the degree of drying
required. See programme chart.
For delicates and fabrics with the
following wash care label r dry using
the Low temperature option.
Items filled with down.
The fabric lining on these garments
may shrink depending on the quality.
They can be partially dried using the
Smoothing programme.
Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the wash care label,
as the surface of the fabric may
otherwise "roughen". These items can
be partially dried using the Smoothing
programme.
Woven and loopknit materials (e.g.
T-shirts, knitted garments) have a
tendency to shrink, depending on their
quality and this is made worse by
over-drying. When purchasing these
garments it is advisable to take their
shrinkage properties into account.
Never overload the drum. Do not
exceed the maximum recommended
loads given in the "Programme
chart". Overloading can cause
unnecessary wear and tear to the
laundry, give a disappointing drying
result and cause more creasing.
Minimum iron fabrics and 100% cotton
shirts or blouses tend to crease more,
the larger the load being dried,
particulary when the weave of the
fabric is very fine. Reduce the load or
use the MINIMUM IRON - Hand iron
programme with a max. load of 1 kg. If
this is unsatisfactory use the Special
care "Smoothing" setting, then hang the
garments on a hanger to dry.
Do not put soaking wet items into
the tumble dryer. Spin them
thoroughly after washing using the
appropriate spin speed.
Starched laundry can be dried in the
tumble dryer. In order to achieve the
usual finish, double the amount of
starch should be used.
Tips on drying
Woollens and wool blends tend to
become matted and shrink if dried in a
tumble dryer. They can, however, be
partially dried using the Woollens hand
care programme.
10
New dark coloured garments should be
dried separately from light coloured
garments to avoid the danger of colours running.
Programme chart
Programmes
Fabric type
Special notes
Drying levels
maximum load: 5 kg (1)
COTTONS
Multi-layered fabrics, which Do not dry jersey wear in the
would not be thoroughly
Extra dry programme dried using the "Normal +"
tendency to shrink.
programme.
Single and multi-layered
fabrics, e.g. mixed load of
cotton fabrics (e.g.
towelling, jerseywear).
Extra dry
Normal +
Normal (2)
Hand iron
Hand iron rr
Machine iron
(1)
(2)
(2)
Load of similar fabrics
(jersey wear, flannelette
sheets, towelling).
If laundry is still too damp,
then:
- finish drying using Timed
drying "Warm air".
- Use the"Normal +"
programme next time.
Cotton or linen fabrics (e.g.
table linen, bedlinen,
starched laundry etc).
If laundry is still too damp
for hand ironing, then select
"Hand iron r" in the future.
Cotton or linen fabrics,
The laundry should be rolled
including starched laundry, up to prevent it from drying
for machine ironing.
out before it can be ironed.
Weight of dry laundry
Note for test institutes: These programmes are to be
used when testing according to EN 61121 standard
11
Programme chart
Programme
Fabric type
Special notes
Drying levels
maximum load: 2.5 kg (1)
MINIMUM IRON
Normal +
Minimum iron items which are
made of synthetic or blended
fabrics (e.g. pullovers,
dresses, trousers) which are
not dried adequately in the
"Normal" programme.
Spin minimum iron fabrics for
at least 30 seconds in the
washing machine before
drying.
Normal (2)
Minimum iron shirts, table
cloths etc. made of blended
fabrics (e.g.
cotton/synthetics).
Minimum iron shirts, table
cloths etc. made of blended
fabrics (e.g. cottons and
synthetics), which are still to
be hand ironed.
Spin minimum iron fabrics for
at least 30 seconds in the
washing machine before
drying.
Spin minimum iron fabrics for
at least 30 seconds in the
washing machine before
drying. For extra special care
of delicate fabrics and to
reduce creasing even more,
reduce the load to 1 kg. See
also "Special care
programmes")
Hand iron
maximum load: 5 kg (1)
TIMED DRYING
Warm air
Individual items
(e.g. bathing costumes, bath
towels, tea-towels).
Multi-layered fabric whose
layers have different drying
characteristics.
-
Cool air
Items which are to be aired
only.
-
(1)
(2)
12
Weight of dry laundry
Note for test institutes: These programmes are to be
used when testing according to EN 61121 standard.
Programme chart
Programme
Fabric type
Special care programmes
Woollens
hand care
Woollen fabrics
maximum load: 2 kg (1)
To refresh and fluff up woollen
garments quickly. Remove garments
immediately at the end of the
programme. Do not repeat.
Woollen fabrics are not dried
completely by this programme.
maximum load: 2.5 kg (1)
Smoothing
Cottons and linen fabrics.
Minimum iron items made
of cotton, blended fabrics
or synthetics, e.g. cotton
trousers, shirts.
(1)
Special notes
Smooths out creasing caused during
the spin cycle in the washing
machine.
Fabrics are not completely dried in
this programme.
Remove garments immediately at
the end of the programme and place
on a line or hangers to dry.
Weight of dry laundry
Selecting additional options
Programme
Additional option button(s)
Anti-crease, Short, Low temperature, Buzzer
COTTONS
Anti-crease, Short, Low temperature, Buzzer
MINIMUM IRON
Anti-crease, Low temperature, Buzzer
TIMED DRYING - Warm air
Buzzer
- Cool air
Buzzer
Woollens hand care
Buzzer
Smoothing
For delicates and fabrics with the following wash care label r select the Low
temperature option.
13
How to dry correctly
A Prepare the laundry
^ As far as possible, sort laundry for:
- the type of fibre or weave,
- the degree of dryness required,
- similar size of items,
- the moisture content after
spinning.
This will help towards achieving an
even drying result.
Fasten duvet covers etc. to prevent
small items from being rolled up inside
them.
Do not overload the drum.
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
See the "Programme chart" for
maximum recommended loads.
^ Before closing the door check that
the fluff filter is correctly positioned in
the door.
Do up zips, hooks and eyes etc.
Tie fabric belts, apron strings.
Sew in or remove underwiring from
bras.
Make sure there is no detergent
dispenser ball etc. in with the
laundry, as this could melt and
damage the machine and the
laundry.
B Load the drum and switch
on the dryer
^ Press the door button and open the
door.
^ Load the laundry loosely into the
drum.
When closing the door make sure
items of laundry cannot be trapped
by the door, as this will cause
damage to the laundry.
^ Shut the door either with a gentle
swing or lean against it and push it
shut.
^ Switch the dryer on by pressing the
"l-On/0-Off" button.
14
How to dry correctly
C Select a programme
^ Turn the programme selector to the
required programme.
COTTONS and
MINIMUM IRON
The electronic unit uses the residual
moisture content to estimate the
programme duration. This is an
approximate drying time. See
"Consumption data" chart for
programme durations.
Woollens hand care and Smoothing
See the "Consumption data" chart for
programme durations.
TIMED DRYING
The programme duration is shown in
the control panel display.
D Select any additional
option(s)
^ Press the relevant button(s) for the
additional option(s) required.
It is not possible to activate additional
options which are incompatible with the
drying programme selected. If an
inappropriate combination of options is
selected (e.g. "Short" and "Low
temperature") only the last option
selected will be activated.
Anti-crease
Once a programme has ended, the
drum will turn at regular intervals for
approx. 60 minutes to prevent the
laundry from settling into creases or
folds.
Always select anti-crease if laundry is
not going to be removed from the drum
as soon as the programme has
finished. Anti-crease can be activated
or deactivated after a programme has
started.
15
How to dry correctly
Short
For drying fabrics which can
withstand high temperatures, e.g.
pure linens and cottons. Do not use
on minimum iron or delicate fabrics.
– Because the heater rating is
increased clothes dry faster thus
shortening drying times.
Low temperature
For drying delicate fabrics with the
symbol r (e.g. acrylic garments) at a
lower temperature.
– Because the heater rating is reduced
clothes dry more slowly thus
lengthening drying times.
Buzzer
An audible tone sounds repeatedly at
the end of a programme.
The buzzer can be switched on or off
after a programme has started.
The volume (and pitch) of the buzzer
can be adjusted before a programme is
started:
^ Select the programme.
^ Press the Buzzer button (the Buzzer
indicator lamp will light up), until the
desired volume / pitch is achieved.
Then release the button.
E Start the programme.
^ Press the START button.
The drying cycle begins.
16
The drying stage reached is shown by
the sequence indicator lamps on the
right hand side of the control panel.
At the end of the drying phase, a
cooling down phase commences to
cool the laundry down (the Cool air
indicator lamp lights up).
The drying level required has now been
reached.
F At the end of a programme
When the drying programme has
finished the Anti-crease / finish
sequence indicator lamp will come on
and the buzzer will sound.
^ Press the Door button and open the
drum door.
^ Remove the laundry.
Make sure that the drum is empty. If
items are left in the dryer, they could
be damaged by overdrying when
the dryer is next used.
^ After every cycle remove the fluff
from the fluff filter in the door and in
the door opening (see "Cleaning and
Care").
^ Empty the condensed water
container (where there is no external
drainage of the water).
^ The condenser unit should be
cleaned on a regular basis (see
"Cleaning and Care").
^ After each use, switch the dryer off
by pressing the l-On / 0-Off button.
^ Always close the door after use.
How to dry correctly
Additional notes
C Select a programme
. . . Clean out airways indicator lamp
^ Turn the programme selector to the
required programme.
This indicator lamp comes on to warn
you that the dryer is not working
efficiently.
Additional option(s) can be selected
(point D) if required.
This may be because:
D Select additional option(s)
– the fluff filters are clogged;
^ Press the relevant button(s) for the
additional function(s) required.
– the condenser unit is clogged.
E Start the programme
Brief instructions
^ Press the START button.
Recommendation:
F At the end of the programme
To help you become familiar with
operating the dryer, please make sure
that you also read the detailed
instructions at the beginning of this
section.
– the indicator lamp Anti-crease /
Finish lights up and the buzzer
sounds.
A Sort the laundry
^ Switch the dryer off by pressing the
l-On/0-Off button and close the door.
B Load the dryer and switch it on
^ Open the door and remove the
laundry.
^ Press the Door button and open the
door.
^ Load the drum and close the door.
^ Switch the dryer on with the
l-On/0-Off button.
17
How to dry correctly
Changing a programme
Adding or removing items
If the programme selector is turned to a
different programme after a programme
has begun, this will not affect the
programme. The Anti-crease / Finish
indicator lamp will flash. The indicator
lamp will go out when the selector is
returned to its original position.
^ Press the Door button and open the
door.
After a programme has started, not all
additional options can be switched on
or off (see section "How to dry
correctly").
^ Items can now be added or removed
early.
Interrupting a programme
^ Switch the machine off with the I-On /
0-Off button.
To continue drying:
^ Switch the machine back on with the
I-On / 0-Off button.
The programme will continue, as long
as the cooling down phase has not
been reached.
To cancel a programme and select a
different programme
^ Turn the programme selector to
Finish.
The programme has been
successfully cancelled when only the
Anti-crease/Finish indicator lamp is
on.
^ Turn the programme selector to the
required programme.
^ Switch additional options on or off as
required.
^ Press the START button.
18
,Do not touch the back of the
drum when adding or removing
items. The drum could be very hot danger of burning.
To continue drying:
^ Close the door.
^ Press the START button.
– The programme will continue.
Electronic system lock
The system lock prevents anyone
from interfering with the dryer.
If the system lock has been activated it
is not possible to start a programme.
The following steps (A,B,C...) must
be carried out in the correct order.
To activate the system lock
A Ensure that the door is closed and
that the programme selector is
turned to Finish.
B Switch the machine on.
C Press the Short button and keep it
pressed in whilst carrying out steps
D to F.
D Slowly turn the programme selector
clockwise step by step until it
reaches the COTTONS Normal
position.
E Slowly turn the programme selector
anti-clockwise step by step to Finish.
F Slowly turn the programme selector
anti-clockwise step by step to the
MINIMUM IRON Hand iron position.
The Locked indicator lamp will flash.
G Then release the Short button.
The system lock is now activated.
H Switch the machine off with the I-On /
0-Off button.
To deactivate the system lock
^ Repeat steps A-G.
The Locked indicator lamp will go out
after step F.
19
Cleaning and care
Emptying the condensed
water container
The condensed water will be collected
in the condensed water container
unless the machine has been fitted with
a drain hose (see installation).
The condensed water container
should be emptied after every
drying cycle or as soon as the
Empty out container indicator lamp
comes on.
The drying programme will be
interrupted if the maximum level of the
condensed water container is reached.
The Empty out container indicator lamp
comes on and the buzzer sounds.
^ Open the shutter and empty out the
water.
^ To replace the container hold it at a
slight angle (as when removing it)
and push it in gently until you feel it
click into position.
^ Before starting a new programme,
first switch the machine off and then
on again. The Empty out container
indicator lamp will go out.
Condensed water should not be
consumed. It could lead to health
problems for people and animals.
^ Grip the container firmly with both
hands, as shown, and pull it out
slightly towards the right-hand side.
^ Hold the container with both hands
and carry it in a horizontal position.
20
Condensed water can be put to
household use (e.g. used in a steam
iron or humidifier). To ensure that any
residual particles of fluff in the
condensed water are removed before
use, pass it through a fine sieve or
paper filter first.
Cleaning and care
Cleaning the fluff filters
The fluff which is created by the drying
process is collected by the fluff filters in
the door and the door opening. Clean
the filters after each drying programme.
Cleaning them whilst dry
^ Remove any fluff from the hollow part
of the door holder. A cleaning brush
is available as an optional extra from
your Miele dealer or the Miele Spare
Parts Department.
Tip: You can also use a vacuum
cleaner.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.
^ Open the door and pull the fluff filter
out of the door as illustrated.
^ Use your fingers to remove the fluff
from the two fluff filters in the door
opening.
^ Close the door.
^ Use your fingers to remove the fluff
from the surface of the filter.
21
Cleaning and care
Cleaning them with water
If there is a great deal of compacted
fluff on any of the filters, they can be
removed and cleaned under hot
running water.
^ To remove the fluff filter from the door
holder see previous page.
^ Place the filters back in the door
opening (the left and right filters are
identical) with the finger holders
facing upwards. See illustration.
Cleaning the tumble dryer
Disconnect the machine from the
mains electricity supply.
^ Clean the housing and control panel
with a slightly damp cloth and a mild
detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable
proprietary stainless steel cleaner
following the manufacturer's
instructions.
^ Grip the holder and push the filter in
the door opening upwards in the
direction of the arrow to remove it. Do
the same on the opposite filter.
^ Rinse the filters under hot, running
water.
^ Then shake the filters until no more
water droplets are visible.
^ Dry the filters thoroughly with care.
,Do not replace them if they are
damp or wet. Damp or wet filters
could cause operational faults.
^ Push the large filter back into the
door holder until it clicks into position.
Ensure it is facing the correct way.
22
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic sufaces and other
parts. The machine must never be
hosed down.
^ Dry all parts with a soft cloth.
^ A microfibre E-Cloth is available from
the Miele UK Spare Parts Department
which is suitable for cleaning
surfaces such as stainless steel,
glass, plastic and chrome without the
use of chemicals. It can be washed
300 times.
Cleaning and care
Cleaning the condenser unit
Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.
Check the condenser unit at least
twice a year. If the dryer is used
frequently then clean the condenser
unit after approx. 100 drying cycles.
Removing the condenser unit
^ Turn the lever on the inner cover
downwards to the vertical position.
^ Pull the cover forwards
^ Then remove it by pulling it
diagonally upwards.
^ Open the service panel by pressing
the two lower corners at the same
time (see illustration).
The hooks at the side will prevent the
panel from falling off.
^ Turn the lever on the condenser unit
to the vertical position.
^ Now the remove the panel by pulling
it diagonally upwards.
^ Then place it to one side.
23
Cleaning and care
If you cannot see any fluff:
^ Replace the condenser unit (see
following page).
If you can see some fluff:
^ Clean the condenser unit as
described below.
Cleaning the condenser unit
^ When rinsing the condenser unit,
make sure you position it as shown in
the next two illustrations.
^ Pull the condenser unit out of its
housing by the handle.
Checking the condenser unit
^ Use a shower head or similar to rinse
the unit out as shown.
^ Hold the condenser unit up to the
light as shown.
^ Check to see if there is any fluff
inside it.
The arrows in the illustration above
indicate where to look.
24
Cleaning and care
Replacing the condenser unit
^ With the handle facing upwards,
push the condenser unit back into
position in its housing.
^ Turn the lever down to the horizontal
position, making sure that the hook
on the lever clicks into the groove.
When replacing the cover after
cleaning, ensure that the rubber seal
fits correctly into the groove.
^ Then flush the unit through from the
front.
^ Check the condenser unit again for
any visible fluff and if necessary flush
it through again until it has all gone.
^ Remove any soiling still visible inside
the housing unit.
^ Also make sure the rubber seals are
clean.
The rubber seals must not be
removed and must be free of kinks.
^ Shake any excess water out of the
unit until no more water droplets are
visible.
^ Replace the cover making sure the
hooks locate correctly. Hold it at an
angle and push it gently downwards.
^ Then turn the lever upwards into the
horizontal position to lock the cover.
^ Replace the service panel and press
the upper edge until it clicks into
position.
It is important to ensure that both the
condenser unit and the cover are
correctly positioned and locked.
Otherwise water may leak from the
machine.
25
Problem solving guide
With the help of the following notes minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical equipment should only be carried out by a suitably
qualified person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
General problems
Problem
Possible cause
The tumble dryer fails to No obvious cause.
start when switched on.
Items made of synthetic Synthetic fibres tend to
fibres are charged with attract static charge.
static electricity after
drying.
26
Remedy
– Have you followed the
switch-on procedure
correctly (see “How to
dry correctly”)?
– Is the plug correctly
inserted in the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
machine or a fabric
conditioner sheet to the
load in the dryer.
Problem solving guide
Problem
Possible cause
Remedy
There is a build up
of fluff.
Fluff is principally the result
of friction when garments
are being worn and
washed. Machine drying
hardly causes any fluff to
form and has been
established by research
institutes to have no effect
on the lifetime of fabric.
The load consisted of
different fabrics.
Fluff is collected by the fluff
filters and can be easily
removed (see "Cleaning
and Care").
– Finish drying using
"Timed drying - Warm
air".
– Select a more suitable
drying programme next
time (see "Programme
chart").
There are water
A double filter system with Laundry being removed
droplets at the upper dual insulation prevents fluff from the machine may
from being deposited in the come into contact with
edge of the drum
these water droplets, but
condenser unit. This
aperture.
they will dry off in a matter
insulation can lead to a
of minutes.
build-up of condensation.
The laundry is not
sufficiently dry.
27
Problem solving guide
Problem
Possible cause
Remedy
The drying process Important: Before attempting to remedy one of the
goes on too long or following causes, switch the dryer off and switch on again
even switches off. to start the programme again.
Ventilation to and from the
Open a door or window
while the machine is in
dryer may be insufficient
(e.g because it is installed in operation for increased air
a small room). This has
flow.
caused the temperature in
the room to rise sharply.
The fluff filters are clogged
– Remove any fluff.
up with fluff or were still wet – The fluff filters must be
when they were replaced.
completely dry.
The laundry has not been
Make sure that your laundry
spun sufficiently.
is thoroughly spun at
highest spin speed for the
type of fabric.
The tumble dryer has been
overloaded.
Metallic components, e.g.
zips have prevented the
dryer from registering the
correct moisture level in the
laundry.
Do not exceed the maximum
load for the programme
selected.
– Close zips and fasten any
hooks next time.
If the problem occurs again,
dry garments with long zips
using "Timed drying - Warm
air".
Detergent residues, hair and Check the condenser unit
fine fibres can block up the from time to time and clean
condenser unit.
it if necessary (see
"Cleaning and Care").
The vents below the door
are blocked.
28
Remove any objects that are
blocking the vents.
Problem solving guide
Problem
Possible cause
Remedy
The inner cover of the
condenser unit has not
been locked properly
and/or the condenser unit
has not been positioned
correctly.
Water leaks from the Fluff has collected at the
machine after the
bottom of the condenser
condenser unit has unit housing.
been cleaned.
The lighting switched off
The interior drum
lighting does not
automatically.
come on.
– Ensure that the condenser
unit is positioned correctly
and lock the cover.
– Check the rubber seals.
The ring around the The lighting switched off
programme selector automatically.
does not light up.
It lights up when drying is in
progress and goes out
shortly after the end of the
programme to save energy.
The condenser unit
service panel will
not shut.
– Use a cloth to remove any
fluff from the inside of the
condenser unit housing.
The lighting only comes on
when the door is opened if
the dryer is switched on. To
save energy the lighting
goes out after a while if the
door is left open.
The lamp needs changing. Change the lamp as
described at the end of this
section.
Check and fault indicator lamps
Problem
Possible cause
Remedy
The Anti-crease /
Finish indicator
lamp flashes while
drying is in
progress.
The programme selector
was moved after the start
of a programme. The
programme continues to
run as normal.
The system lock is
activated.
Turn the selector back to the
original position and the
indicator lamp will go out.
The Locked
indicator lamp
flashes when the
machine is switched
on and the
programme cannot
be started.
If you wish to use the dryer,
the system lock must be
deactivated (see "Electronic
system lock").
29
Problem solving guide
Problem
Possible cause
Remedy
The Clean out
airways lamp comes
on.
The fluff filters may be
blocked.
The condenser unit may be
blocked with fluff and
detergent residues.
Remove any fluff (see
"Cleaning and care").
The programme
stops and the Clean
out airways lamp
flashes.
The Empty out
container indicator
lamp comes on.
30
Please note that the
condenser unit must be
cleaned regularly (see
"Cleaning and care").
The check lamp will go out
when the door is opened.
Possible causes and remedies are described above in
(The Clean out airways lamp comes on).
There is no obvious cause. – Switch off the dryer.
– Then switch the dryer
back on and start the
programme again.
If the programme stops
again and the Clean out
airways lamp flashes, there
is a fault. Contact the Miele
Service Department.
– Empty out the
The condensed water
condensed water
container is full or there is
container.
kink in the drain hose.
– Check the drain hose.
– Before starting a new
programme, first switch
the dryer off and then on
again.
Problem solving guide
Problem
Possible cause
Remedy
The programme has
stopped. The
Anti-crease/Finish
lamp has come on in
the sequence display
and the buzzer is
sounding.
This is not a fault.
The electronic unit has
recognised that there is no
laundry in the drum and
cancelled the programme.
Drying individual garments
or items which are already
dry can also cause the
programme to be stopped.
No obvious cause.
Use the "Timed drying Warm air" programme to
dry individual items.
Before changing a
programme: Open and
close the drum door.
The programme has
been interrupted. The
indicator lamp for
Hand iron or Machine
iron is flashing, and
the buzzer sounds.
– Switch the dryer off and
then on again.
– Then start the
programme again.
If the programme stops
again and the fault
message reappears there
is a fault. Contact the
Miele Service
Department.
31
Problem solving guide
To change the interior drum
lamp
^ Open the door.
Before changing the lamp,
disconnect the machine from the
mains power supply.
You will find the interior lamp cover at
the top of the drum aperture.
^ Insert the opener under the side
edge of the cover as illustrated.
^ Turn your wrist to make the cover
open downwards.
The temperature resistant lamp should
only be ordered from your Miele dealer
or the Miele Spare Parts Department.
The lamp must not exceed the
maximum wattage quoted on the
data plate and on the lamp cover.
^ Replace the lamp.
32
^ To close the flap push it upwards and
press it on the left and right until you
hear it click into position.
The cover must be fixed securely, as
otherwise moisture may seep in and
cause a short circuit.
Problem solving guide
After sales service
Repairs
Appliance guarantee
In the event of any faults which you
cannot remedy yourself, please contact
The appliance is guaranteed for a
period of 1 year.
– Your Miele Dealer or
See the guarantee card supplied with
the appliance for further details.
– The nearest Miele Service
Department (see back cover for
address).
When contacting the Service
Department, please quote the model
and serial number of your appliance,
both of which are shown on the data
plate situated on the right hand side
below the drum aperture.
Optional accessories
Optional accessories for these dryers
are available from your Miele Dealer or
from the Miele Spare Parts Department.
Please note that telephone calls may
be monitored and recorded to
improve our service.
33
Installation
Front view
a Supply cable for electrical
connection
b Condensed water container
c Control panel
d Door
34
e Service panel for condenser unit
f Four height-adjustable screw feet
g External drainage options (e.g. via
wash basin, wash basin drain outlet,
or gully).
Installation
Installation site
,Make sure the dryer door can be
opened without hindrance after
installation.
Transporting the machine to its
installation site
When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer.
To manoeuvre the dryer out of its
packing case to its installation site you
will also need to hold it by the front feet.
Building under a continous worktop /
in a row of kitchen units
The dryer should not be installed
next to a refrigerator or freezer. The
warm air expelled from the rear of
the dryer would increase the
temperature around the
refrigerator's/freezer's heat
exchanger causing the compressor
to run continuously.
If it is not possible to install the dryer
anywhere else, then the
refrigerator/freezer must be sealed
off from the dryer.
A building under kit* is required.
The machine lid is replaced by a
coverplate which must be fitted by a
suitably qualified person to ensure
electrical safety.
– When installing under a 900/910 mm
high worktop a spacer kit* is
required.
– The electrical socket must be
located in an accessible position
near the machine.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
The building under kit is supplied with
its own installation instructions.
N.B. When built under running times
may be longer.
Replacing the lid
If the lid has been removed in order to
fit a cover plate, ensure that, if the lid is
replaced, it fits securely into the rear
holders. Otherwise, it is not properly
secure for transport.
35
Installation
Aligning the machine
Room in which the dryer is located
Air taken in for use in the drying
process will be warm when it is
expelled from the rear of the dryer. This
expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.
Washer - dryer stack
The machine must be perfectly level to
ensure safe and proper operation.
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit* (WTV)
to match your washing machine is
required.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
Stacking kits must be fitted by a
suitably qualified fitter.
Before moving the machine again
(e.g. when moving house)
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
,The ventilation gaps in the plinth
must not be covered over as this
would prevent a sufficient intake of
air.
36
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the machine is tipped up when it
is being moved. It is a good idea to run
the Cool air programme for
approximately 1 minute before moving
the machine. Any remaining
condensed water will then be fed into
the condensed water container or out
through the drain hose.
Installation
External condensed water
outlet
From the back of the dryer at the
bottom:
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose
at the back of the dryer. The
condensed water can also be drained
off directly if the machine is installed
near a sink, drain outlet etc. so that
the condensed water container does
not have to be emptied.
The drain hose (approx. 2 m long) is
stored in the dryer. It must be pulled
out of the dryer to its full extent if
condensed water is to be drained
externally.
Maximum delivery head: 1 m.
If it is not long enough, an extension
hose is available as an optional
accessory through your dealer or from
the Miele Spare Parts Dept.
Pulling out the drain hose
From the back of the dryer at the top:
^ Unclip the drain hose from holder (3).
^ Then pull the drain hose completely
out of the dryer towards the left (4)
(See illustration).
,Important: do not let the drain
hose become kinked as this could
damage it.
,If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Use the bow-shaped guide to prevent
the drain hose from becoming kinked
(see "Front view" illustration).
^ Unclip the drain hose (1).
^ Then pull it off holder (2).
37
Installation
Connection to a sink drain outlet
The drain hose can be connected
directly to a sink drain outlet.
If this nut has a flat disc sealing it you
should take the disc out first.
Important: if this nut has a washer or
seal in it this must not be removed!
^ Attach the end of the hose to adapter
1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
If you no longer wish to use an
external condensed water outlet
,Do not push the drain hose
back into the dryer. Doing this could
cause it to become kinked and
damaged in the dryer.
^ Remove the following from the back
of the dryer at the bottom:
Adapter 1 and hose clip 3 behind it.
^ Loop the drain hose up.
^ Use a suitable cable tie to secure the
looped hose to the back of the dryer,
or simply lay the looped hose behind
the dryer.
^ Attach the open end of the drain
hose back onto the holder at the
back of the dryer at the top (see
holder 2 in "Pulling out the drain
hose").
^ Fit adapter 1 to the sink drain outlet
using nut 2.
38
Electrical connection
Electrical connection U.K.
All electrical work should be carried out
only by a suitably qualified and
competent person, in strict accordance
with national and local safety
regulations.
Ensure power is not supplied to the
machine while installation work is being
carried out.
The machine is supplied with a mains
cable with moulded plug for connection
to a 230-240V mains supply. The
voltage, rated load and fuse rating
are given on the data plate. Please
ensure these match the household
mains supply.
Connection should be made via a fused
plug and suitable switched socket
which is easily accessible after
installation.
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100, section
739).
Do not connect via an extension lead.
Important
The wires in the mains lead are
coloured in accordance with the
following code:
Electrical connection U.K.
Non-rewireable plugs BS 1363
If this machine is fitted with a
non-rewireable plug and the socket
outlets are not suitable for the plug
supplied or if the existing plug needs to
be replaced by a new one, the old plug
will need to be cut off and an
appropriate plug fitted. The fuse carrier
and the fuse should be removed from
the old plug and disposed of.
The plug cut from the cable should then
be disposed of and on no account be
inserted into any socket elsewhere in
the house (electric shock hazard).
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier or Service
agent.
Green/yellow = earth
Blue
= neutral
Brown
= live
39
Electrical connection
If the colours of the wires in the mains
lead of this machine do not correspond
with the coloured markings identifying
the terminals of your plug, proceed as
follows:
^ The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth
symbol z or coloured green, or
green and yellow.
^ The wire which is coloured blue must
be connected to the terminal in the
plug which is marked with the letter N
or coloured black.
^ The wire which is coloured brown
must be connected to the terminal in
the plug which is marked with the
letter L or coloured red.
WARNING: THIS APPLIANCE
MUST BE EARTHED
40
Consumption data
Capacity
Final spin speed
(in a domestic
washing machine)
Electricity
consumption
Drying time
incl.
cooling down
time
kg
rpm
kWh
Minutes
Extra dry
5.0
Normal +
5.0
1200
1400
1600
1200
1400
1600
3.25
3.10
2.85
2.80
2.65
2.40
86
83
76
76
73
66
Normal (1)
5.0
800 (70 % residual moisture)
3.40
Normal
5.0
1200
1400
1600
2.65
2.55
2.25
89
73
70
63
Programme
COTTONS
(1)
5.0
800 (70 % residual moisture)
Hand iron
5.0
Machine iron
5.0
1200
1400
1600
1200
1400
1600
2.75
2.00
1.90
1.60
1.60
1.50
1.20
72
55
52
46
46
43
36
Hand iron
MINIMUM IRON
Normal (1)
2.5
1000 (50 % residual moisture)
1.25
40
Hand iron
2.5
1000
1.10
36
Woollens hand care
2.0
-
0.20
4
Smoothing
2.5
-
0.30
9
Special care
(1)
EN 61121 test programme
EN 61121 Standard testing
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry
with 70% residual moisture as per the above standard using the Normal Cottons
programme without selecting any additional functions.
Consumption data can vary from the nominal values given above depending
on the size of the load, types of textiles, residual moisture levels after spinning,
fluctuations in the electricity supply and any additional options selected.
41
Technical data
Height
85 cm (adjustable +0.7/- 0.7 cm)
Height without lid
82 cm
Width
59.5 cm
Depth
58 cm
Depth with door open
Weight
106 cm
54 kg
Drum volume
Maximum capacity
100 litres
5 kg dry weight
Capacity of condensed
water container
Length of connection cable
approx. 3.5 litres
1.60 m
Maximum delivery head
Maximum drain hose length
1m
3m
Voltage
Rated load
see data plate
see data plate
Fuse rating
Lamp wattage
see data plate
see data plate
Energy consumption
Test certificates awarded
see "Consumption data"
Radio/TV suppressed, VDE
42
Programmable functions
for changing
standard settings
43
Programmable functions
Increased drying level
The machine is designed to dry
using as little energy as possible.
However, if you require the laundry to
be drier, it is possible to reduce the
final moisture level in the COTTONS
and MINIMUM IRON programmes.
Note that programme durations will
be longer if this option is activated.
The machine is supplied ex-works with
this option switched off. It can be
activated is wished.
increased drying level is
deactivated.
– If the Machine iron indicator lamp
lights up, the increased drying level
is activated.
E Pressing the START button switches
between activating and deactivating
increased drying.
F Switch the machine off with the I-On /
0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
Programming and storing in memory
The programmable functions are
activated with the help of the additional
option buttons and the programme
selector.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Low temperature and
Buzzer buttons at the same time,
keep them pressed in
and ...
B ... switch the dryer on with the I-On /
0-Off button.
C Then release these buttons.
– The Drying and Cool air sequence
indicator lamps will flash.
D Turn the programme selector to the
COTTONS Extra dry position.
– If the Machine iron sequence
indicator does not light up, the
44
To check:
^ Carry out steps A to D.
If the indicator light for Machine iron
lights up = Increased drying level is
switched on
does not light up = Increased drying
level is switched off
^ Switch the machine off with the I-On /
0-Off button.
The check is complete.
Programmable functions
Memory function
The additional options selected
previously for specific programmes
are stored in the machine’s memory.
The machine is supplied ex-works with
the memory function switched off. It can
be activated is wished.
Programming and storing in memory
The programmable functions are
activated with the help of the additional
option buttons and the programme
selector.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Low temperature and
Buzzer buttons at the same time,
keep them pressed in
and ...
B ... switch the dryer on with the I-On /
0-Off button.
D Turn the programme selector to
COTTONS Normal.
– If the Machine iron sequence
indicator does not light up, the
Memory function is deactivated.
– If the Machine iron sequence
indicator does light up, the Memory
function is activated.
E Pressing the START button switches
between activating and deactivating
the Memory function.
F Switch the machine off with the I-On /
0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Carry out steps A to D.
If the indicator light for Machine iron
lights up = the Memory function is
switched on
does not light up = the Memory
function is switched off
C Then release these buttons.
^ Switch the machine off with the I-On /
0-Off button.
– The Drying and Cool air sequence
indicator lamps will flash.
The check is complete.
45
46
47
Alteration rights reserved/4703
M.-Nr. 05 993 030 / 01
This paper consists of cellulose which has been bleached without the use of chlorine.