Samsung CE101K Instruction manual

Test Report issued under the responsibility of
www.nemko.com
TEST REPORT
IEC 60335-2-40
Safety of household and similar electrical appliances
Part 2-40: Particular requirements for electrical heat pumps, air
conditioners and dehumidifiers
Report Reference No. ...................... :
236145
Date of issue....................................... :
2013-04-26
Total number of pages ........................
97 pages
CB/CCA Testing Laboratory Name :
Nemko AS
Address............................................... :
Gaustadalléen 30, NO - 0373 Oslo, Norway
Applicant's name.............................. :
Samsung Electronics Co., Ltd.
Address............................................... :
Digital Air-solutions Business Team,
129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do,
443-742 Korea, Republic of
Phone: (+47) 22 96 03 30
Test specification:
Standard ............................................. :
IEC 60335-2-40:2002 (4. Edition) + A1:2005 (incl. Corr.1:2006) +
A2:2005 with
IEC 60335-1:2001 (4. Edition) (incl. Corr.1:2002) + A1:2004 (incl.
Corr.1:2005) + A2:2006 (incl. Corr.1:2006)
IEC 62233:2005 (1. Edition)
Test procedure ................................... :
CB
Non-standard test method…………..:
N/A
Test Report Form No. ...................... :
IEC60335_2_40F
Test Report Form(s) Originator ..........................:
VDE Testing and Certification Institute
Master TRF .........................................................:
Dated 2009-11
Copyright © 2009 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright
owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's
interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme
procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended
to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
This Test Report, when bearing the Nemko name and logo is only valid when issued by a Nemko laboratory, or
by a laboratory having special agreement with Nemko.
Page 2 of 97
Test item description ....................... :
Report No. 236145
Air-conditioner
Trade Mark ......................................... :
Manufacturer ...................................... :
Same as applicant.
Samsung Electronics Co., Ltd.
Digital Air-solutions Business Team,
129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do,
443-742 Korea, Republic of
Model/Type reference ........................ :
(Indoor unit)
a) AM140FNHDEH;
b) AM128FNHDEH;
c) AM112FNHDEH
Ratings................................................ :
a) 3.0 A 385 W 220 – 240 V~ 50 Hz
b) 2.58 A 333 W 220 – 240 V~ 50 Hz
c) 2.35 A 305 W 220 – 240 V~ 50 Hz
Additional information......................... :
TRF No. IEC60335_2_40F
Cl. I, Built-in duct type, Climate class T1 or T3, Indoor unit only.
Optional accessory product;
- Drain pump: model, MDP-E075SEE3D
Page 3 of 97
Report No. 236145
Testing procedure and testing location:
CB/CCA Testing Laboratory:
N/A
Testing location/ address ........................ :
Associated CB Laboratory:
N/A
Testing location/ address ........................ :
Tested by (name + signature) .......:
Approved by (+ signature) .............:
Testing procedure: TMP
Tested by (name + signature) .......:
Approved by (+ signature) ............. :
Testing location/ address ........................ :
Jae Hyeon, Kim
Jae Hong, Park
Samsung Electronics Co., Ltd.
Digital Air-solutions Business Team,
129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do,
443-742 Korea, Republic of
Testing procedure: WMT
N/A
Tested by (name + signature) .......:
Witnessed by (+ signature) ........... :
Approved by (+ signature) .............:
Testing location/ address ........................ :
Testing procedure: SMT
N/A
Tested by (name + signature) .......:
Approved by (+ signature) ..............:
Supervised by (+ signature) ..........:
Testing location/ address ........................ :
Testing procedure: RMT
Tested by (name + signature) .......:
Approved by (+ signature) ..............:
Supervised by (+ signature) ..........:
Testing location/ address ........................ :
TRF No. IEC60335_2_40F
N/A
Page 4 of 97
Report No. 236145
Summary of testing:
Tests performed (name of test and test clause):
- Clause 7: Marking and instructions
- Clause 8: Protection against access to live parts
- Clause10: Power input and current
- Clause 11: Heating
- Clause 13: Leakage current and electric strength at
operating temperature
- Clause 15: Moisture resistance
- Clause 16: Leakage current and electric strength
- Clause 19: Abnormal operation
- Clause 20: Stability and mechanical hazards
- Clause 21: Mechanical strength
- Clause 22: Construction
- Clause 23: Internal wiring
- Clause 24: Components
- Clause 25: Supply connection and external flexible
cord
- Clause 26: Terminals for external conductors
- Clause 27: Provision for earthing
- Clause 28: Screws and connections
- Clause 29: Clearances, creepage distances and
solid insulation
- Clause 30: Resistance to heat and fire
- Annex E: Needle flame test
- Annex N: Proof tracking test
- Annex EE: Pressure test
Testing location:
Samsung Electronics Co., Ltd.
Digital Air-solutions Business Team,
129, Samsung-ro, Yeongtong-gu, Suwon-si,
Gyeonggi-do, 443-742 Korea, Republic of
1. Safety test conditions;
Normal temperature condition was considered as following based on ISO 13253 and ISO 15042;
- For climatic class T1, an appliance was installed with the indoor side subjected to 27C and the outdoor
side subjected to 35C for cooling function.
- For climatic class T3, an appliance was installed with the indoor side subjected to 29C and the outdoor
side subjected to 46C for cooling function.
- An appliance was installed with the indoor side subjected to 20C and the outdoor side subjected to 7C for
heating function.
2. EMF test conditions;
1) Measuring distance (r1): 30 cm
2) Sensor locations: Around
3) Operating conditions: Continuously.
Cooling mode: Lowest cooling, Heating mode: Highest heating
3. In this test report, the model AM140FNHDEH (indoor unit, built-in duct type) was mainly tested and
evaluated as a representative by connecting it with the model AM100FXVAGH (outdoor unit).
4. Heat exchanger of this appliance was tested and evaluated with the refrigerant R410A only in this test
report.
5. The appliance shall be provided with a certified supply cord and interconnection cords complying with the
national regulations of the countries in which the appliance is to be sold. The supply cord and
interconnection cords were evaluated just for the reference in this test report.
TRF No. IEC60335_2_40F
Page 5 of 97
Report No. 236145
Summary of testing:
6. This test report replaces the previous test report no. 235559 by following;
- Revision on the critical component list.
Refer to the Table 24.1 in main test report.
7. Information about other standards/ documents considered;
1) ISO 5149 (1993, edition:1);
Mechanical refrigerating systems used for cooling and heating – Safety requirements
2) ISO 13253 (2011, edition:2);
Ducted air-conditioners and air-to-air heat pumps -- Testing and rating for performance
3) ISO 15042 (2011, edition:1);
Multiple split-system air-conditioners and air-to-air heat pumps -- Testing and rating for performance
Summary of compliance with National Differences:
1) All CENELEC members as listed in the following standards;
EN 60335-2-40:2003 +A11:2004 +A12: 2005 +A1:2006 +A2:2009
EN 60335-1:2002 +A11:2004 +A1:2004 +A12:2006 +A2:2006 +A13:2008
EN 62233:2008
2) All CB members as listed in the IECEE Online Bulletin. All National differences listed in the CB Bulletin are
covered by the National Differences and Group Differences for Europe (Common Modifications, Special
National Conditions).
3) The product fulfils the requirements of the following standards;
IEC 60335-2-40: 2002 (Fourth edition) +A1:2005 +A2:2005
IEC 60335-1:2001 (Fourth ed.) (incl. Corr.1:2002) +A1:2004 +A2:2006 (incl. Corr. 1:2006)
EN 60335-2-40:2003 +A11:2004 +A12: 2005 +A1:2006 +A2:2009
EN 60335-1:2002 +A11:2004 +A1:2004 +A12:2006 +A2:2006 +A13:2008
EN 62233:2008
TRF No. IEC60335_2_40F
Page 6 of 97
Report No. 236145
Copy of marking plate: 1 / 3
Model: AM140FNHDEH (Indoor unit)
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
TRF No. IEC60335_2_40F
Page 7 of 97
Report No. 236145
Copy of marking plate: 2 / 3
Model: AM128FNHDEH (Indoor unit)
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
TRF No. IEC60335_2_40F
Page 8 of 97
Report No. 236145
Copy of marking plate: 3 / 3
Model: AM112FNHDEH (Indoor unit)
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
TRF No. IEC60335_2_40F
Page 9 of 97
Report No. 236145
Name and address of production-sites (Factories):
Factories are introduced as following;
No.
Address
Factory 1:
SUZHOU SAMSUNG ELECTRONICS CO., LTD.
501, Suhong East Road, Suzhou City, Jiangsu, 215021 China
Factory 2:
SUZHOU SAMSUNG ELECTRONICS CO., LTD.
218 Jiepu Road, Industry Park, Suzhou City, Jiangsu, China
Factory 3:
SAMSUNG ELECTRONICS CO., LTD.
107, Hanamsandan 6beon-ro, Gwangsan-gu, Gwangju-si,
506-723, Korea, Republic of
Factory 4:
THAI SAMSUNG ELECTRONICS CO., LTD.
313 Moo 1 Sukhaphiban 8 Rd.,
Sriracha Industry Park, T.Bung, A.Sriracha Chonburi, 20230 Thailand
Factory 5:
HANCHANG CO., LTD.
22, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea, Republic of
List of attachments:
1. Attachment 1 (13 pages):
Attachment report to the IEC 60335-2-40 for European Group Differences and National Differences;
Attachment Form No. ............ : EU_GD_IEC60335_2_40F
Attachment Originator ............ : VDE
Master Attachment................. : 2009-11
2. Attachment 2 (4 pages):
National Difference of Australia (AU) in the IECEE Online Bulletin. (http://www.iecee.org)
No.
IEC standard
National standard reference
1
IEC 60335-1 (Fourth edition); am1; am2
AS/NZS 60335.1: 2002
Last modification: 2010-04-19
2
IEC 60335-2-40 (Fourth edition); am1; am2
AS/NZS 60335.2.40: 2006
No national deviation for Australia (AU).
3. Attachment 3 (4 pages):
Schematic wiring/ Circuit diagram.
4. Attachment 4 (8 pages):
Photos of appliance.
TRF No. IEC60335_2_40F
Page 10 of 97
Report No. 236145
Test item particulars .................................................. : Air-conditioner
Classification of installation and use............................ : Fixed / Stationary appliance / Built-in duct type
Supply Connection ....................................................... : Type Y attachment
...................................................................................... :
...................................................................................... :
Possible test case verdicts:
- test case does not apply to the test object ................. : N/A
- test object does meet the requirement ....................... : P (Pass)
- test object does not meet the requirement................. : F (Fail)
Testing .......................................................................... :
Date of receipt of test item ............................................ : 2013-04-15
Date (s) of performance of tests ................................... : 2013-04-16 to 2013-04-25
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
Throughout this report a comma is used as the decimal separator.
General product information:
1) This test report is for the models of indoor unit as following;
a) AM140FNHDEH;
b) AM128FNHDEH;
c) AM112FNHDEH
2) The variant models, AM128FNHDEH; AM112FNHDEH are same as the model AM140FNHDEH just
except for the electrical rating by the difference of outdoor unit which is connected with indoor unit.
3) Each model has different rated cooling/ heating capacity for the outdoor unit which is combined with the
indoor unit.
4) This appliance is not considered having any IP degrees, i.e. IPX0.
5) This appliance is not intended to be installed where accessible to the general public, which is intended to
be maintained by qualified service personnel and located at a level not less than 2,5m.
6) This test report is just for the indoor unit, and the indoor unit/ outdoor unit shall be installed by a service
agent or similarly qualified persons with an end user’s preference with the combination specified by
manufacturer.
TRF No. IEC60335_2_40F
Page 11 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
5
GENERAL CONDITIONS FOR THE TESTS
5.2
Result
Verdict
—
Tests performed according to cl. 5, e.g. nature of
supply, sequence of testing, etc.
All the tests are conducted
according to this standard.
If the test of annex D has to be carried out, an
additional appliance may be used (IEC 60335-1/A1)
Not applicable.
Tests of clause 21 carried out on separate samples.
Tests of clauses 11, 19 and 21 require pressure
measurements made at various points in
refrigerating system (IEC 60335-2-40/A1)
Performed according to the
requirement.
P
N/A
P
At least one additional specially prepared sample
required for tests of annex FF (Leak simulation tests)
(IEC 60335-2-40/A1)
P
Temperatures on refrigerant piping measured during Tested as this clause.
test of clause 11 (IEC 60335-2-40/A1)
P
5.3
The tests of clause 14 and 21.2 and 22.24 are
carried out after the tests of clause 29
(IEC 60335-1/A1)
5.6
Appropriate controls rendered inoperative during test Tested as this clause.
(IEC 60335-2-40)
P
5.7
Tests of clauses 10 and 11 carried out under most
severe operating conditions within operating
temperature range specified by manufacturer.
Annex AA provide examples of such temperature
conditions (IEC 60335-2-40)
Annex AA: A7 A20.
Also considered ISO 13253
and ISO 15042.
P
5.10
For split-package units, refrigerant lines installed in
accordance with installation instructions
(IEC 60335-2-40)
Provide with indoor unit and
outdoor unit in separate.
Installed as its instructions.
P
Not applicable.
Refrigerant line length is maximum length stated in
installation instructions or (IEC 60335-2-40)
5.14
N/A
N/A
7,5 m, whichever is shorter (IEC 60335-2-40)
7,5 m
P
Thermal insulation of refrigerant lines applied in
accordance with installation instructions
(IEC 60335-2-40)
Applied as instructions.
P
NOTE: Guidance is given in annex P for enhanced
requirements that may be used to ensure an
acceptable level of protection against electrical and
thermal hazards for particular types of appliances
used in an installation without a protective earthing
conductor in countries that have warm damp
equable climates (IEC 60335-1/A1)
Not applicable.
TRF No. IEC60335_2_40F
N/A
Page 12 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
5.101
Motor-compressor subjected to relevant test of
clause 19 of IEC 60335-2-34, unless
(IEC 60335-2-40)
Not checked in the appliance.
For the relevant tests of indoor
unit, the outdoor unit was
installed equipped with a
motor-compressor which is
approved by NEMKO
employing a non-flammable
refrigerant of R410A.
motor-compressor comply with that standard
(IEC 60335-2-40)
Verdict
N/A
N/A
5.102
Motor-compressors tested and comply with
IEC 60335-2-34 need not additionally tested for
clause 21 (IEC 60335-2-40/A1)
6
CLASSIFICATION
6.1
Protection against electric shock:
Class I, II, III (IEC 60335-2-40)
6.2
Protection against harmful ingress of water, IP degree in accordance with IEC 60529
(IEC 60335-2-40)
Not checked in the appliance.
N/A
—
Class I appliance.
- appliances or parts intended for outdoor use be at
least IPX4 (IEC 60335-2-40);
Not checked in the appliance.
- appliances intended only for indoor use (excluding
laundry rooms) be IPX0 (IEC 60335-2-40);
IPX0 for indoor unit.
- appliances intended to be used in laundry rooms be
at least IPX1 (IEC 60335-2-40).
P
—
N/A
P
N/A
6.101
Degree of accessibility (accessible/not accessible to
the general public) (IEC 60335-2-40)
7
MARKING AND INSTRUCTIONS
7.1
Rated voltage or voltage range (V)..........................:
220 – 240 V
P
Symbol for nature of supply including number of
phases, unless for single phase operation
(IEC 60335-2-40)......................................................:
Provided with symbol (~) and
frequency (50 Hz).
P
Rated frequency (Hz) ...............................................:
50 Hz
P
Rated power input (W) .............................................:
Marked.
385 W or 333 W or 305 W
P
Rated current (A) ......................................................:
Marked.
3.0 A or 2.58 A or 2.35 A
P
Manufacturer's or responsible vendor's name,
trademark or identification mark ..............................:
TRF No. IEC60335_2_40F
Not intended to be installed
where accessible to the
general public.
P
—
P
Page 13 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Model or type reference ...........................................:
(Indoor unit)
a) AM140FNHDEH;
b) AM128FNHDEH;
c) AM112FNHDEH
Symbol 5172 of IEC 60417, for class II appliances
Class I appliance.
Verdict
P
N/A
Symbol IEC 60417-5036, for the enclosure of
Not intended to be connected
electrically-operated water valves in external
to the water mains.
hose-sets for connection of an appliance to the water
mains (IEC 60335-1/A1)
N/A
Mass of refrigerant or of each refrigerant in blend
(except for azeotropic type) (IEC 60335-2-40) ........:
Not checked in the appliance
N/A
Refrigerant identification (IEC 60335-2-40).............:
Not checked in the appliance
N/A
Permissible excessive operating pressure for
sanitary hot water heat pumps (IEC 60335-2-40) ...:
Not such an appliance.
N/A
Maximum operating pressure for heat exchanger for
hydronic fan coil/air handling units
(IEC 60335-2-40/A2) ................................................:
No hydronic unit.
N/A
Permissible excessive operating pressure of
refrigerant circuit for suction and discharge, if they
differ (IEC 60335-2-40) ............................................:
Not marked with marking plate
for indoor unit.
N/A
Symbol for degree of protection against ingress of
water, other than IPX0 (IEC 60335-2-40) ................:
IPX0 for indoor unit.
N/A
Separate marking of appliances with all rated
characteristics of supplementary heaters
(IEC 60335-2-40)......................................................:
No supplementary haters.
N/A
Marking of direction of fluid flow (IEC 60335-2-40)
It can be distinguished from the
different diameter of pipes.
N/A
Flame symbol and instruction manual symbol of 7.6 visible when flammable
refrigerant employed and following conditions exist (IEC 60335-2-40/A1):
- accessing parts expected to be subjected to
maintenance or repair (IEC 60335-2-40/A1);
Intended for the use of a nonflammable refrigerant.
—
N/A
- observing appliance under sale or installed
conditions (IEC 60335-2-40/A1);
N/A
- observing appliance packaging, if appliance
charged with refrigerant (IEC 60335-2-40/A1).
N/A
If flammable refrigerant used, symbols for “read
operator’s manual”, “operator’s manual; operating
instructions” and “service indicator; read technical
manual” (symbols 0790, 1641 and 1659 of
ISO 7000) placed on appliance in location visible to
persons required to know information. Perpendicular
height be at least 10 mm (IEC 60335-2-40/A1 corr.1)
N/A
TRF No. IEC60335_2_40F
Page 14 of 97
Report No. 236145
IEC 60335-2-40
Clause
7.2
7.3
Requirement – Test
Result
Additional warning symbol (flame symbol: B.3.2 of
ISO 3864) placed on nameplate of unit near
declaration of refrigerant type and charge
information. Perpendicular height be at least 10 mm,
and symbol need not be in colour
(IEC 60335-2-40/A1)
N/A
Following warning also applied to appliance when
flammable refrigerant employed.
WARNING
Appliance shall be installed, operated and stored in a
room with a floor area larger than ‘X’ m² (only applies
to appliances that are not fixed appliances)
(IEC 60335-2-40/A1)
N/A
Not fixed appliances, minimum room size X specified
on appliance. X in marking determined in m² by
procedure described in paragraph 2 of annex GG for
unventilated areas and X in marking be 4 if
refrigerant charge of appliance is less than m1 (see
annex GG, paragraph 1.1) (IEC 60335-2-40/A1)
N/A
Maximum allowable pressure for low-pressure side
and high-pressure side marked on product
(IEC 60335-2-40/A1)
N/A
If not already visible when accessing service port
and if service port provided, service port marked to
identify type of refrigerant. If refrigerant is flammable,
symbol B.3.2 of ISO 3864, be included, without
specifying the colour (IEC 60335-2-40/A1)
N/A
Warning for stationary appliances for multiple supply
P
Warning placed in vicinity of terminal cover
P
Range of rated values marked with the lower and
upper limits separated by a hyphen
220 – 240 V
Different rated values marked with the values
separated by an oblique stroke
Appliances adjustable for different rated voltages,
the voltage setting is clearly discernible
7.5
Appliances with more than one rated voltage or one Single rated voltage range of
or more rated voltage ranges, marked with rated
220 – 240 V.
power input or rated current for each rated voltage or
range, unless
Not adjustable for different
rated voltages.
the power input is related to the mean value of the
rated voltage range
Relation between marking for upper and lower limits
of rated power input or rated current and voltage is
clear
TRF No. IEC60335_2_40F
N/A
N/A
P
Single rated voltage range of
220 – 240 V.
power input is related to the arithmetic mean value of
the rated voltage range (IEC 60335-1/A2)
Correct symbols used
P
N/A
7.4
7.6
Verdict
N/A
P
Correct symbols are used.
P
Page 15 of 97
Report No. 236145
IEC 60335-2-40
Clause
7.7
7.8
Requirement – Test
Result
Verdict
Flammable refrigerant, warning symbol B.3.2 of
Intended for the use of a nonISO 3864, including colour and format, permanently flammable refrigerant.
placed on appliance. Perpendicular height of triangle
containing
"Caution, risk of fire"
symbol be at least 30 mm (IEC 60335-2-40/A1)
N/A
Flammable refrigerant, symbol requiring reference to
manual [0790 of ISO 7000], including colour and
format, permanently placed on appliance
(IEC 60335-2-40/A1 corr.1)
N/A
Connection diagram fixed to appliances to be
connected to more than two supply conductors and
appliances for multiple supply
Indicated by letters;
1(L), 2(N)
N/A
Considered as correct mode of
connection.
Except for type Z attachment, terminals for connection to the supply mains indicated
as follows:
- marking of terminals exclusively for the neutral
conductor (N)
—
N/A
- marking of protective earthing terminals
(symbol 5019 of IEC 60417)
Protective earthing terminal is
provided.
- marking not placed on removable parts
No marking on removable
parts.
N/A
7.9
Marking or placing of switches which may cause a
hazard
No hazard.
N/A
7.10
Indications of switches on stationary appliances and With visual means for indoor
controls on all appliances by use of figures, letters or unit.
other visual means ...................................................:
P
P
On LED display:
The figure 0 indicates only OFF position, unless no
confusion with the OFF position
For address setting of
communication between the
indoor unit and outdoor unit.
P
7.11
Indication for direction of adjustment of controls
7.12
Instructions for safe use provided
Provided with user/ installation
manual.
P
Appliances not accessible to general public,
classification of clause 6.101 included
(IEC 60335-2-40)
Not accessible to the general
public.
Described on installation
manual.
P
Appliances using flammable refrigerants, an
installation, service and operation manual, either
separate or combined manuals, provided and
include information given in annex DD
(IEC 60335-2-40/A1)
Intended for the use of a nonflammable refrigerant.
N/A
TRF No. IEC60335_2_40F
P
Page 16 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Instructions state that (IEC 60335-1/A2):
7.12.1
Verdict
—
- Appliance is not to be used by children or persons
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction (IEC 60335-1/A2)
Adequately described similar
sentences on user manual.
P
- Children being supervised not to play with
appliance (IEC 60335-1/A2)
Described on user manual.
P
Sufficient details for installation or maintenance supplied (IEC 60335-2-40):
—
- that the appliance shall be installed in accordance
with national wiring regulations (IEC 60335-2-40);
P
- the dimensions of the space necessary for correct
installation of the appliance including the minimum
permissible distance to adjacent structures
(IEC 60335-2-40);
P
- for appliances with supplementary heaters, the
minimum clearance from the appliance to
combustible surfaces (IEC 60335-2-40);
No supplementary heaters.
N/A
- a wiring diagram with a clear indication of the
connections and wiring to external control devices
and supply cord (IEC 60335-2-40);
P
- the range of external static pressures at which the
appliance was tested (add-on heat pump,s and
appliances with supplementary heaters only)
(IEC 60335-2-40);
N/A
- the method of connection to the appliance to the
electrical supply and interconnection of separate
components (IEC 60335-2-40);
- indication of which parts of the appliance are
suitable for outdoor use, if applicable
(IEC 60335-2-40);
- details of type and rating of fuses
(IEC 60335-2-40);
P
N/A
P
- details of supplementary heating elements that may
be used in conjunction with the appliance, including
fitting instructions either with the appliance or with
the supplementary heater (IEC 60335-2-40);
N/A
- maximum and minimum water or brine operating
temperatures (IEC 60335-2-40);
N/A
- maximum and minimum water or brine operating
pressures (IEC 60335-2-40).
N/A
Open storage tanks of heat pumps for water heating,
accompanied by an instruction sheet which state that
the vent shall not be obstructed (IEC 60335-2-40)
N/A
TRF No. IEC60335_2_40F
Page 17 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
7.12.2
Stationary appliances not fitted with means for
disconnection from the supply mains having a
contact separation in all poles that provide full
disconnection under overvoltage category III, the
instructions state that means for disconnection must
be incorporated in the fixed wiring in accordance
with the wiring rules
N/A
7.12.3
Insulation of the fixed wiring in contact with parts
exceeding 50 K during clause 11; instructions stating
that the fixed wiring must be protected
N/A
7.12.4
Instructions for built-in appliances:
- dimensions of space
7.12.5
Result
Verdict
—
Built-in duct type.
P
- dimensions and position of supporting means
P
- distances between parts and surrounding structure
P
- dimensions of ventilation openings and
arrangement
P
- connection to supply mains and interconnection of
separate components
P
- allow disconnection of the appliance after
installation, by accessible plug or a switch in the
fixed wiring, unless (IEC 60335-1/A1)
Not checked in this test report.
N/A
a switch complying with 24.3 (IEC 60335-1/A1)
Not checked in this test report.
N/A
The disconnection may be achieved by having the
plug accessible or by incorporating a switch in the
fixed wiring in accordance with the wiring rules
(IEC 60335-1/A1)
Not checked in this test report.
N/A
Replacement cord instructions, type X attachment
with a specially prepared cord
Replacement cord instructions, type Y attachment
N/A
Type Y attachment.
Replacement cord instructions, type Z attachment
P
N/A
7.12.6
Caution in the instructions for heating appliances
with a non-self resetting thermal cut-out
(IEC 60335-1/A1)
7.12.7
Instructions for fixed appliances stating how the
appliance is to be fixed (IEC 60335-1/A1)
P
7.12.8
Instructions for appliances connected to the water mains (IEC 60335-1/A1):
—
- max. inlet water pressure (Pa) (IEC 60335-1/A1) .:
Not a heating appliance.
Not intended to be connected
to the water mains.
N/A
N/A
- min. inlet water pressure, if necessary (Pa)
(IEC 60335-1/A1) ...................................................:
N/A
Instructions concerning new and old hose-sets for
appliances connected to the water mains by
detachable hose-sets (IEC 60335-1/A1)
N/A
TRF No. IEC60335_2_40F
Page 18 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
7.13
Instructions and other texts in an official language
In English.
P
7.14
Marking clearly legible and durable
Legible. No curling.
No damage.
P
7.15
Marking on a main part
Marked on the main part.
P
Marking clearly discernible from the outside, if
necessary after removal of a cover
Clearly discernible.
P
For portable appliances, cover can be removed or
opened without a tool
Verdict
N/A
For stationary appliances, name, trademark or
identification mark and model or type reference
visible after installation
P
For fixed appliances, name, trademark or
identification mark and model or type reference
visible after installation according to the instructions
P
Indications for switches and controls placed on or
near the components. Marking not on parts which
can be positioned or repositioned in such a way that
the marking is misleading
P
Marking on panel allowed, provided panel in place
for intended operation of appliance (IEC 60335-2-40)
P
7.16
Marking of a possible replaceable thermal link or
fuse link clearly visible with regard to replacing the
link
7.101
Marking of fuses and overload protective devices, if replaceable (IEC 60335-2-40):
- fuse rated current in amperes, type and rated
voltage or (IEC 60335-2-40)
Clearly visible.
Not intended to be replaceable
by the user. Shall be replaced
by any qualified personnel.
- manufacturer and model of overload protective
device (IEC 60335-2-40)
P
—
N/A
N/A
7.102
Marking for connection with aluminium wire, if
necessary (IEC 60335-2-40)
8
PROTECTION AGAINST ACCESS TO LIVE PARTS
8.1
Adequate protection against accidental contact with
live parts
Adequately protected.
P
8.1.1
Requirement applies for all positions, detachable
parts removed
Adequately protected.
P
Insertion or removal of lamps, protection against
contact with live parts of the lamp cap
No lamps.
Use of test probe B of IEC 61032: no contact with
live parts
No contacts.
8.1.2
No aluminium wire.
—
Use of test probe 13 of IEC 61032 through openings Class I appliance.
in class 0 appliances and class II appliances/
constructions: no contact with live parts
TRF No. IEC60335_2_40F
N/A
N/A
P
N/A
Page 19 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Test probe 13 also applied through openings in
earthed metal enclosures having a non-conductive
coating: no contact with live parts
8.1.3
For appliances other than class II, use of test
probe 41 of IEC 61032: no contact with live parts of
visible glowing heating elements
8.1.4
Accessible part not considered live if:
- safety extra-low a.c. voltage: peak value not
exceeding 42,4 V
8.1.5
8.2
Verdict
N/A
No visible glowing heating
elements.
N/A
—
Adequately protected.
N/A
- safety extra-low d.c. voltage: not exceeding 42,4 V
N/A
- or separated from live parts by protective
impedance
N/A
If protective impedance: d.c. current not exceeding
2 mA, and
N/A
a.c. peak value not exceeding 0,7 mA
N/A
- for peak values over 42,4 V up to and including
450 V, capacitance not exceeding 0,1 F
N/A
- for peak values over 450 V up to and including
15 kV, discharge not exceeding 45 C
N/A
The quantity of electricity in the discharge is
measured using a resistor having a nominal
non-inductive resistance of 2000 Ω
(IEC 60335-1/A1)
N/A
- for peak values over 15 kV energy of discharge not
exceed 350 mJ (IEC 60335-1/A2)
N/A
Live parts protected at least by basic insulation before installation or assembly:
—
- built-in appliances
Intended for built-in use.
P
- fixed appliances
Fixed appliance.
P
- appliances delivered in separate units
Intended to be delivered as
separate units: Indoor unit and
outdoor unit.
P
Class II appliances and constructions constructed so Class I appliance.
that there is adequate protection against accidental
contact with basic insulation and metal parts
separated from live parts by basic insulation only
N/A
Only possible to touch parts separated from live
parts by double or reinforced insulation
N/A
10
POWER INPUT AND CURRENT
10.1
Power input at normal operating temperature, rated
voltage and normal operation not deviating from
rated power input by more than shown in table 1
TRF No. IEC60335_2_40F
Class I appliance.
—
(See appended table)
P
Page 20 of 97
Report No. 236145
IEC 60335-2-40
Clause
10.2
Requirement – Test
Result
Deviation of appliance with one or more rated
voltage ranges (IEC 60335-1/A2)
Rated: 220 – 240 V.
Measured at arithmetic mean
value of the rated voltage
range.
P
Current at normal operating temperature, rated
voltage and normal operation not deviating from
rated current by more than shown in table 2
(See appended table)
P
Deviation of appliance with one or more rated
voltage ranges (IEC 60335-1/A2)
Rated: 220 – 240 V.
Measured at arithmetic mean
value of the rated voltage
range.
P
11
HEATING
11.1
No excessive temperatures in normal use
(IEC 60335-2-40)
—
No excessive temperatures.
Compliance is checked by the tests of annex C, if (IEC 60335-2-40):
11.2
Verdict
P
—
- temperature of motor winding exceeds values
shown in table 3 (IEC 60335-2-40)
Not exceeded.
N/A
- there is doubt about classification of insulation
system of the motor (IEC 60335-2-40)
No doubt about the
classification of insulation
system of motors.
N/A
Placing and mounting of appliance (IEC 60335-2-40):
—
- clearances to adjacent surfaces (IEC 60335-2-40);
Installed in accordance to the
manual.
- flow rates for liquid source or sink equipment be
minimum, except for fan coils where flow rates and
liquid temperatures be maximum
(IEC 60335-2-40/A2);
No means for adjustment.
P
N/A
- static pressures (IEC 60335-2-40);
N/A
- means of adjusting the flow, flow for tests be
minimum obtainable (IEC 60335-2-40);
N/A
- adjustable limit controls set at maximum cut-out
setting and minimum differential (IEC 60335-2-40).
No adjustable limit controls.
N/A
Appliances with supplementary heaters, use test
casing of clause 11.9 (IEC 60335-2-40)
No supplementary heaters.
N/A
11.2.1
Appliances with supplementary heaters, inlet duct
connected to inlet air opening (IEC 60335-2-40)
No supplementary heaters.
N/A
11.2.2
Appliance without supplementary heaters, air outlet
used (IEC 60335-2-40)
11.3
Temperature rise determine by thermocouples or
resistance method (IEC 60335-2-40)
By thermocouple method.
P
11.4
Test performed at supply voltage between 0,94 and
1,06 times the rated voltage (IEC 60335-2-40)
Tested as this clause.
P
TRF No. IEC60335_2_40F
N/A
Page 21 of 97
Report No. 236145
IEC 60335-2-40
Clause
11.5
Requirement – Test
Result
Heating elements energized at voltage which gives
an electrical input of 1,15 times maximum rated
power input (IEC 60335-2-40)
Motor operated appliance.
Test conducted in heating mode and cooling mode, if At both lowest cooling and
both exist (IEC 60335-2-40)
highest heating mode.
All supplementary heating elements operative
simultaneously (IEC 60335-2-40)
No supplementary heaters.
Verdict
N/A
P
N/A
11.6
Defrost test in most unfavourable conditions, if
needed (IEC 60335-2-40)
11.7
Appliances operated continuously until steady
conditions except for defrost tests (IEC 60335-2-40)
Operated until steady
conditions are established.
P
11.8
Temperatures not exceeding values of table 3
(IEC 60335-2-40/A2)
(See appended tables)
P
Protective devices do not operate (IEC 60335-2-40)
Not operated.
P
N/A
Sealing compound not flowing out (IEC 60335-2-40)
P
Temperature of air in outlet duct not exceed 90 °C
(IEC 60335-2-40)
11.9
Test casing and installation of appliances in
accordance with manufacturer’s instructions
(IEC 60335-2-40)
N/A
Not considered.
Glass fibre insulation for appliances without
indication of minimum clearances according to
manufacturer; thermocouple in contact with
enclosure (IEC 60335-2-40)
N/A
N/A
13
LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING
TEMPERATURE
—
13.1
Leakage current not excessive and electric strength
adequate
P
Heating appliances operated at 1,15 times rated
power input ...............................................................:
No heating elements.
Motor-operated appliances and combined
appliances supplied at 1,06 times rated voltage .....:
1,06 x 240V~ 50Hz
Protective impedance and radio interference filters
disconnected before carrying out the tests
13.2
13.3
N/A
P
P
Leakage current measured by means of the circuit
described in figure 4 of IEC 60990
Tested by this measurement
circuit.
P
Leakage current measurements (IEC 60335-2-40)
(See appended table)
P
Appliance disconnected from supply and insulation is Applied test voltages to each
immediately subjected to voltage having frequency
insulation as specified.
of 50 Hz or 60 Hz for 1 min, in accordance with
IEC 61180-1 (IEC 60335-1/A1)
TRF No. IEC60335_2_40F
P
Page 22 of 97
Report No. 236145
IEC 60335-2-40
Clause
14
Requirement – Test
Result
Verdict
High-voltage source used for test is to be capable of (See appended table)
supplying short circuit current Is between the output
terminals after output voltage adjusted to appropriate
test voltage (IEC 60335-1/A1)
P
(See appended table)
Overload release of circuit is not to be operated by
any current below tripping current Ir. Values of Is and
Ir given in table 5 for various high-voltage sources
(IEC 60335-1/A1)
P
No breakdown during the tests
P
No breakdown.
—
TRANSIENT OVERVOLTAGES
Appliances withstand the transient overvoltages to
which they may be subjected
Not applicable.
N/A
Clearances having a value less than specified in
table 16 subjected to an impulse voltage test, the
test voltage specified in table 6
N/A
No flashover during the test, unless of functional
insulation
N/A
In case of flashover of functional insulation, the
appliance complies with clause 19 with the clearance
short circuited
N/A
15
MOISTURE RESISTANCE
15.1
Enclosure provides degree of moisture protection
against ingress of water (rain, overflow from drain
pan or defrosting), tests of clause 15.2, 15.3, 11.6
and 16) (IEC 60335-2-40)
—
IPX0 for indoor unit.
Adequately prevented from
spillage of liquid and overflow
which may reduce clearances
and creepage distances.
Motor-compressor not operated and detachable
parts removed during tests of clause 15.2 and 15.3
(IEC 60335-2-40/A2)
P
P
15.2
Tests in accordance with IEC 60529 in appliances
other than IPX0, as specified (IEC 60335-2-40) .....:
IPX0 for indoor unit.
15.3
Drain pan filled to brim and subjected to continuous
overflow and fan(s) switched on (IEC 60335-2-40)
Adequately prevented from
spillage of liquid and overflow
which may reduce clearances
and creepage distances.
P
15.101
Spillage test as specified (IEC 60335-2-40/A2)
Not accessible to the general
public.
Described on the installation
manual it shall be installed at a
level of 2,5 m above the floor
or grade level.
N/A
After spillage completed, appliance withstand test of
clause 16 (IEC 60335-2-40/A2)
TRF No. IEC60335_2_40F
N/A
N/A
Page 23 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
16
LEAKAGE CURRENT AND ELECTRIC STRENGTH
—
16.1
Leakage current not excessive and electric strength
adequate
P
Protective impedance disconnected from live parts
before carrying out the tests
P
16.2
Single-phase appliances: test voltage 1,06 times
rated voltage .............................................................:
Result
1,06 x 240V~ 50Hz
Three-phase appliances: test voltage 1,06 times
rated voltage divided by 3 ......................................:
16.3
17
Verdict
P
N/A
Leakage current measurements (IEC 60335-2-40)
(See appended table)
P
Electric strength tests according to table 7
(See appended table)
P
No breakdown during the tests
No breakdown.
P
OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS
—
No excessive temperatures in transformer or
associated circuits in event of short-circuits likely to
occur in normal use
N/A
Appliance supplied with 1,06 or 0,94 times rated
voltage and the most unfavourable short-circuit or
overload likely to occur in normal use applied ........:
N/A
Temperature rise of insulation of the conductors of
safety extra-low voltage circuits not exceeding the
relevant value specified in table 3 by more than 15 K
N/A
Temperature of the winding not exceeding the value
specified in table 8,
N/A
however limits do not apply to fail-safe transformers
complying with sub-clause 15.5 of IEC 61558-1
N/A
19
ABNORMAL OPERATION
—
19.1
The risk of fire or mechanical damage under
abnormal or careless operation obviated (tests 19.219.14) (IEC 60335-2-40)
P
Failure of transfer medium flow or of any control
device not result in a hazard (IEC 60335-2-40)
P
Electronic circuits so designed and applied that a
fault will not render the appliance unsafe (electric
shock, fire or mechanical hazard, dangerous
malfunction) (test 19.11 and 19.12)
(IEC 60335-2-40)
P
TRF No. IEC60335_2_40F
Page 24 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
19.2
Test of appliance with motor rotors, other than
motor-compressors, operated for 15 days (360 h) or
until protection device opens circuit
(IEC 60335-2-40)
Fan motor for indoor unit is a
brushless DC type.
Impedance protected.
P
Insulation of motor windings (IEC 60335-2-40).......:
Cl. B (Cl. 130)
P
Temperature of enclosure does not exceed (C)
(IEC 60335-2-40)......................................................:
Indoor fan motor:
P
Temperature of the windings does not exceed the
values shown in the table ; temperature (C)
(IEC 60335-2-40)......................................................:
Indoor fan motor:
Electric strength test as specified in 16.3, 72 h after
the beginning of the test (IEC 60335-2-40)
Between windings and
enclosure: 1250V for 1min
- DL-12840SSBF : 98.8 °C
- ZWD-183-BA02: 63.1 °C
Results: Less than 150 C.
No hazard.
P
- DL-12840SSBF: 111.0 °C
- ZWD-183-BA02: 63.5 °C
Results: Less than 165 C.
No hazard.
30 mA residual current device does not open
(IEC 60335-2-40)
19.3
Verdict
P
P
At the end, leakage current between windings and
enclosure does not exceed 2 mA (IEC 60335-2-40)
Less than 2mA
Motor-compressor complies with IEC 60335-2-34
(IEC 60335-2-40)
Not checked in the appliance.
P
N/A
Test of motor-compressor with rotor locked as
specified in clause 19.101 of IEC 60335-2-34 and
comply with 19.104 of that standard
(IEC 60335-2-40)
N/A
19.4
Test of three-phase motors operated under
conditions of clause 11 with one phase disconnected
until steady conditions or protective device operates
(IEC 60335-2-40)
N/A
19.5
Test of appliance with heat transfer medium flow of
the outdoor heat exchanger restricted or shut off
when reaching steady conditions (IEC 60335-2-40)
(see appended table)
Results: No hazard.
No severe temperature rise.
P
Test of appliance with heat transfer flow of the indoor (see appended table)
heat exchanger restricted or shut off when reaching Results: No hazard.
steady conditions (IEC 60335-2-40)
No severe temperature rise.
P
Disconnection of motor common to both the outdoor
and the indoor heat exchangers when reaching
steady conditions (IEC 60335-2-40)
N/A
19.6
Test of appliances using water as heat transfer
medium (IEC 60335-2-40)
19.7
Test of air to air appliances at rated voltage or at the Results: No hazard.
upper limit of the rated voltage range. Dry-bulb
No severe temperature rise.
temperature is 5 K below values specified by
manufacturer (IEC 60335-2-40)
TRF No. IEC60335_2_40F
Not such an appliance.
N/A
P
Page 25 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Test with the dry-bulb temperature 10 K over the
values specified by manufacturer (IEC 60335-2-40)
(see appended table)
Results: No hazard.
No severe temperature rise.
P
19.8
Test of appliances with supplementary heaters
(IEC 60335-2-40)
No supplementary heaters.
N/A
19.9
Test at temperature permitting continuous operation
of the motor-compressor and electric heating
elements at same time (IEC 60335-2-40)
No supplementary heaters.
N/A
19.10
Test of appliance with any defect which expected
during normal use (IEC 60335-2-40)
(see appended table)
Results: No hazard.
No severe temperature rise.
P
19.10.101
Test of clause 19.10 repeated on class 0I appliances No heating elements.
and class I appliances incorporating tubular
sheathed or embedded heating elements
(IEC 60335-2-40/A2)
N/A
However, controls not short-circuited but one end of
element connected to sheath of heating element
(IEC 60335-2-40/A2)
N/A
Test repeated with polarity of supply to appliance
reversed and with other end of element connected to
sheath (IEC 60335-2-40/A2)
N/A
Test not carried out on appliances intended to
permanently connected to fixed wiring and on
appliances where an all-pole disconnection occurs
during test of clause 19.10 (IEC 60335-2-40/A2)
N/A
19.11
Electronic circuits, compliance checked by
evaluation of the fault conditions specified in
clause 19.11.2 for all circuits or parts of circuits
(IEC 60335-2-40), unless
(see appended table)
Results: No hazard.
No severe temperature rise.
they comply with conditions specified in
clause 19.11.1 (IEC 60335-2-40)
19.11.1
Verdict
P
N/A
Windings temperature not exceeding values shown
in table 8 (IEC 60335-2-40)
P
Appliance comply with conditions of clause 19.14
(IEC 60335-2-40)
P
Appliance withstands test: a conductor becomes
open circuited and three conditions are met
(IEC 60335-2-40)
N/A
Before applying the fault conditions a) to f) in 19.11.2, it is checked if circuits or parts
of circuit meet both of following conditions (IEC 60335-2-40):
—
- electronic circuit is low-power circuit, that is,
maximum power at low-power points not exceed
15 W according to tests specified (IEC 60335-2-40)
N/A
- protection against electric shock, fire hazard,
mechanical hazard or dangerous malfunction in
other parts of appliance does not rely on correct
functioning of electronic circuit (IEC 60335-2-40)
N/A
TRF No. IEC60335_2_40F
Page 26 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
19.11.2
Fault conditions applied one at a time, appliance operated under conditions specified
in clause 11, but supplied at rated voltage, duration of tests as specified
(IEC 60335-2-40):
a) short circuit of creepage distances and clearances
between live parts of different potential, if these
distances less than values specified in
clause 29.1, unless relevant part is adequately
encapsulated (IEC 60335-2-40)
19.12
—
N/A
b) open circuit at terminals of any component
(IEC 60335-2-40)
c) short circuit if capacitors, unless they comply with
IEC 60384-14 (IEC 60335-2-40)
Verdict
P
Complying with IEC 60384-14.
N/A
d) short circuit of any two terminals of an electronic
component, other than integrated circuits. This
fault condition not applied between circuits of an
optocoupler (IEC 60335-2-40)
P
e) failure of triacs in diode mode (IEC 60335-2-40)
N/A
f) failure of an integrated circuit. Possible hazardous
situations of appliance assessed to ensure that
safety not rely on correct functioning of such
component (IEC 60335-2-40)
P
Short-circuit of low-power circuits (IEC 60335-2-40)
N/A
Duration of tests (IEC 60335-2-40):
—
- as specified in clause 11.7 but only for one
operating cycle, if fault cannot recognised by user
(IEC 60335-2-40);
P
- as specified in clause 19.2, if fault can recognised
by user (IEC 60335-2-40);
P
- until steady conditions stablished (IEC 60335-2-40).
P
Test ended if interruption of supply occurs within the
appliance (IEC 60335-2-40)
P
If electronic circuit operates to ensure compliance
with clause 19, relevant test repeated with single
fault a) to f) simulated (IEC 60335-2-40)
N/A
Fault condition f) applied to encapsulated or similar
components (IEC 60335-2-40)
N/A
PTC’s, NTC’s and VDR’s resistors not short-circuited
if used as specified by manufacturer
(IEC 60335-2-40)
P
If safety of appliance for any of fault conditions
specified in clause 19.11.2 depends on operation of
miniature fuse-link complying with IEC 60127, test
repeated with fuse-link replaced by an ammeter
(IEC 60335-2-40)
P
TRF No. IEC60335_2_40F
Page 27 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Current  2,1 times rated current of fuse-link, circuit
not adequately protected (fuse-link short-circuited)
(IEC 60335-2-40)
N/A
Current  2,75 times rated current of fuse-link, circuit Rated (F100): 250V~ T5A
During testing, F100 broken at
adequately protected (IEC 60335-2-40)
85 A (> 2.75 x 5A),
Considered as adequately
protected.
Current  2,1 and  2,75 times rated current,
fuse-link short-circuited and test carried out during
specified time (IEC 60335-2-40)
Appliances with PTC heating elements test as
specified (IEC 60335-2-40)
No PTC heating elements.
19.14
During tests of clause 19.2 to 19.10.101 and 19.11,
19.12 and 19.13 if appropriate, appliances not emit
flames, molten metal, poisonous or ignitable gas in
hazardous amounts (IEC 60335-2-40/A2)
No flames, molten metal,
poisonous or ignitable gas in
hazardous amounts.
N/A
P
Enclosures not deform (IEC 60335-2-40)
P
Temperature rise not exceed values shown in table 9 (See appended table)
(IEC 60335-2-40)
P
Electric strength test, test voltage as specified in
table 4 (IEC 60335-2-40)
No breakdown.
P
All appliances provided with supplementary heaters
and free air discharge subjected to specified test in
each mode of operation (IEC 60335-2-40/A2)
No supplementary heaters.
N/A
During test temperature not exceed 150 °C but an
overshoot of 25 °C is permitted during first hour
(IEC 60335-2-40/A2)
No supplementary heaters.
N/A
20
STABILITY AND MECHANICAL HAZARDS
20.1
Adequate stability
20.2
P
N/A
19.13
19.101
Verdict
—
Fixed appliance.
N/A
Tilting test through an angle of 10 ° (appliance
placed on an inclined plane/horizontal plane);
appliance does not overturn
N/A
Tilting test repeated on appliances with heating
elements, angle of inclination increased to 15 °
N/A
Possible heating test in overturned position;
temperature rise does not exceed values shown in
table 9
N/A
Moving parts adequately arranged or enclosed as to Adequately arranged and
provide protection against personal injury
protected.
P
Protective enclosures, guards and similar parts are
non-detachable
P
TRF No. IEC60335_2_40F
Page 28 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Adequate mechanical strength and fixing of
protective enclosures
Verdict
P
Self-resetting thermal cut-outs and overcurrent
protective devices not causing a hazard, by
unexpected reclosure
No hazard.
P
Not possible to touch dangerous moving parts with
test probe
No touch with test probe.
Described to be installed at a
level of 2,5 m height on manual
as well.
P
—
21
MECHANICAL STRENGTH
21.1
Appliance has adequate mechanical strength and
constructed as to withstand rough handling
Having adequate mechanical
strength.
P
Checked by applying blows to the appliance in
accordance with test Ehb of IEC 60068-2-75, spring
hammer test, impact energy 0,5 J (IEC 60335-1/A1)
Providing with adequate
mechanical strength.
P
If necessary, supplementary or reinforced insulation
subjected to the electric strength test of 16.3
No doubt, no needs.
N/A
If necessary, repetition of groups of three blows on a No doubt, no needs.
new sample
N/A
Safety requirements specified in annex EE applied. 1) Motor-compressor is not
Pressure test in annex EE applies to parts other than applicable in this test report.
pressure vessels (IEC 60335-2-40/A1)
2) Test location:
Heat exchanger of indoor unit.
P
Test result:
No leakage, damage, or
hazard.
Safety requirements of ISO 5149 applied
(IEC 60335-2-40/A2)
21.2
Complying with ISO 5149.
Accessible parts of solid insulation shall have
sufficient strength to prevent penetration by sharp
implements (IEC 60335-1/A1)
Compliance is checked by subjecting the insulation
to the following test, unless the thickness of
supplementary insulation is at least 1 mm and that of
reinforced insulation is at least 2 mm
(IEC 60335-1/A1)
P
P
1) Supplementary insulation:
Not less than 1mm
P
2) Reinforced insulation:
Not less than 2mm
The insulation is raised to the temperature measured
during the test of clause 11 (IEC 60335-1/A1)
N/A
The surface of the insulation is then scratched by
means of a hardened steel pin, the end of which has
the form of a cone with an angle of 40 °. Its tip is
rounded with a radius of 0,25 mm ± 0,02 mm
(IEC 60335-1/A1)
N/A
TRF No. IEC60335_2_40F
Page 29 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
The pin is held at an angle of 80 ° - 85 ° to the
horizontal and loaded so that the force exerted along
its axis is 10 N ± 0,5 N (IEC 60335-1/A1)
N/A
The scratches are made by drawing the pin along
the surface of the insulation at a speed of
approximately 20 mm/s. Two parallel scratches are
made (IEC 60335-1/A1)
N/A
They are spaced sufficiently apart so that they are
not affected by each other, their length covering
approximately 25 % of the length of the insulation
(IEC 60335-1/A1)
N/A
Two similar scratches are made at 90 ° to the first
pair without crossing them (IEC 60335-1/A1)
N/A
Test fingernail of figure 7 is then applied to the
scratched surface with a force of approximately
10 N. No further damage, such as separation of the
material, shall occur. The insulation shall then
withstand the electric strength test of 16.3.
(IEC 60335-1/A1)
N/A
Hardened steel pin is then applied perpendicularly
with a force of 30 N ± 0,5 N to an unscratched part of
the surface. The insulation shall then withstand the
electric strength test of 16.3 with the pin still applied
and used as one of the electrodes (IEC 60335-1/A1)
N/A
—
22
CONSTRUCTION
22.1
Appliance marked with the first numeral of the IP
system, relevant requirements of IEC 60529 are
fulfilled
22.2
Stationary appliance: means to provide all-pole disconnection from the supply
provided, the following means being available:
—
- a supply cord fitted with a plug
P
IPX0 for indoor unit.
1. Not checked in this test
report.
N/A
2. The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord referring to an installation
manual.
- a switch complying with 24.3
Not checked in this test report.
- a statement in the instruction sheet that a
disconnection incorporated in the fixed wiring is to
be provided
- an appliance inlet
TRF No. IEC60335_2_40F
N/A
P
No appliance inlet.
N/A
Page 30 of 97
Report No. 236145
IEC 60335-2-40
Clause
22.3
Requirement – Test
Result
Verdict
Singe-pole switches and single-pole protective
devices for disconnection of heating elements in
single-phase, permanently connected class 0I and I
appliances, connected to phase conductor
(IEC 60335-1/A2)
N/A
Appliance provided with pins: no undue strain on
socket-outlets
N/A
Applied torque not exceeding 0,25 Nm
N/A
Pull force of 50 N to each pin after the appliance has
being placed in the heating cabinet; when cooled to
room temperature the pins are not displaced by
more than 1 mm
N/A
Each pin subjected to a torque of 0,4 Nm; the pins
are not rotating unless rotating does not impair
compliance with the standard
N/A
22.4
Appliance for heating liquids and appliance causing
undue vibration not provided with pins for insertion
into socket-outlets
No heating liquids or undue
vibration.
N/A
22.5
No risk of electric shock when touching pins of plug,
for appliances having a capacitor with rated
capacitance exceeding 0,1 F, appliance being
disconnected from supply at instant of voltage peak
(IEC 60335-1/A2)
Not provided with the supply
cord fitted with a plug.
N/A
22.6
The appliance is supplied at rated voltage. Any
switch is then placed in the off position and the
appliance is disconnected from the supply mains at
the instant of voltage peak. One second after
disconnection, the voltage between the pins of the
plug is measured with an instrument that does not
appreciably affect the value to be measured
(IEC 60335-1/A1)
N/A
The voltage shall not exceed 34 V
N/A
Electrical insulation not affected by condensing
water or leaking liquid
Constructed so that the
appliance is prevented from
condensing water or leaking
liquid which may cause a
hazard.
P
Electrical insulation of class II appliances not
affected in case of a hose rupture or seal leak
N/A
Electrical insulation not affected by snow penetration Considered the indoor unit
to appliance enclosure (IEC 60335-2-40)
only.
N/A
22.7
Adequate safeguards against the risk of excessive
pressure in appliances provided with
steam-producing devices
N/A
22.8
Electrical connections not subject to pulling during
cleaning of compartments to which access can be
gained without the aid of a tool, and that are likely to
be cleaned in normal use
TRF No. IEC60335_2_40F
No steam-producing devices.
P
Page 31 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
22.9
Insulation, internal wiring, windings, commutators
and slip rings not exposed to oil, grease or similar
substances
Not exposed to oil, grease or
similar substances.
22.10
22.12
P
Adequate insulating properties of oil or grease to
which insulation is exposed
N/A
Not possible to reset voltage-maintained
No such components.
non-self-resetting thermal cut-outs by the operation
of an automatic switching device incorporated within
the appliance (IEC 60335-1/A1)
N/A
Non-self resetting thermal motor protectors have a
trip-free action, unless (IEC 60335-1/A1)
N/A
Self resetting thermal motor
protectors.
they are voltage maintained (IEC 60335-1/A1)
22.11
Verdict
N/A
Location or protection of reset buttons of
non-self-resetting controls is so that accidental
resetting is unlikely (IEC 60335-1/A1)
No reset button.
Reliable fixing of non-detachable parts that provide
the necessary degree of protection against electric
shock, moisture or contact with moving parts
Fixed in a reliable manner by
metal screws, and adequate to
withstand the mechanical
stress.
N/A
P
Obvious locked position of snap-in devices used for
fixing such parts
P
No deterioration of the fixing properties of snap-in
devices used in parts that are likely to be removed
during installation or servicing
P
Tests as described
50 N.
Handles, knobs etc. fixed in a reliable manner
No such parts.
P
N/A
Fixing in wrong position of handles, knobs etc.
indicating position of switches or similar components
not possible
N/A
Axial force 15 N applied to parts, the shape being so
that an axial pull is unlikely to be applied
N/A
Axial force 30 N applied to parts, the shape being so
that an axial pull is likely to be applied
N/A
22.13
Unlikely that handles, when gripped as in normal
use, make the operators hand touch parts having a
temperature rise exceeding the value specified for
handles which are held for short periods only
No such parts.
22.14
No ragged or sharp edges creating a hazard for the
user in normal use, or during user maintenance
No ragged or sharp edges
creating a hazard for the user
in normal use.
Cooling fins are allowed to be
used for its function.
No exposed pointed ends of self tapping screws etc., No exposed pointed ends of
liable to be touched by the user in normal use or
self tapping screws etc.
during user maintenance
TRF No. IEC60335_2_40F
N/A
P
P
Page 32 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
22.15
Storage hooks and the like for flexible cords smooth
and well rounded
Smooth and well rounded.
22.16
Automatic cord reels cause no undue abrasion or
damage to the sheath of the flexible cord, no
breakage of conductors strands, no undue wear of
contacts
No automatic cord reels.
Verdict
P
N/A
Cord reel tested with 6000 operations, as specified
N/A
Electric strength test of 16.3, voltage of 1000 V
applied
N/A
22.17
Spacers not removable from the outside by hand or
by means of a screwdriver or a spanner
22.18
Current-carrying parts and other metal parts resistant Resistant to corrosion in
to corrosion under normal conditions of use
normal use.
22.19
Driving belts not used as electrical insulation
22.20
Direct contact between live parts and thermal
insulation effectively prevented, unless material used
is non-corrosive, non-hygroscopic and
non-combustible
P
Compliance is checked by inspection and, if
necessary, by appropriate test
P
22.21
Wood, cotton, silk, ordinary paper and fibrous or
hygroscopic material not used as insulation, unless
impregnated
No spacer.
No driving belts.
No such materials.
Requirement does not apply to magnesium oxide
and mineral ceramic fibres used for electrical
insulation of heating elements (IEC 60335-1/A2)
N/A
P
N/A
N/A
N/A
22.22
Appliances not containing asbestos
No asbestos.
P
22.23
Oils containing polychlorinated biphenyl (PCB) not
used
No oil containing PCB.
P
22.24
Bare heating elements adequately supported to
prevent contact with accessible metal parts in case
of rupture or sagging (IEC 60335-2-40)
No bare heating elements.
Bare heating elements only used with metal
enclosures (wood or composite enclosures not
allowed) (IEC 60335-2-40)
N/A
N/A
22.25
Sagging heating conductors cannot come into
contact with accessible metal parts
22.26
The insulation between parts operating at safety
extra-low voltage and other live parts complies with
the requirements for double or reinforced insulation
N/A
22.27
Parts connected by protective impedance separated
by double or reinforced insulation
N/A
TRF No. IEC60335_2_40F
No sagging heating conductor.
N/A
Page 33 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
22.28
Metal parts of class II appliances conductively
connected to gas pipes or in contact with water:
separated from live parts by double or reinforced
insulation
N/A
22.29
Class II appliances permanently connected to fixed
wiring so constructed that the required degree of
access to live parts is maintained after installation
N/A
22.30
Parts serving as supplementary or reinforced
insulation fixed so that they cannot be removed
without being seriously damaged, or
P
so constructed that they cannot be replaced in an
incorrect position, and so that if they are omitted, the
appliance is rendered inoperable or manifestly
incomplete
P
22.31
22.32
Clearances and creepage distances over
supplementary and reinforced insulation not reduced
below values specified in clause 29 as a result of
wear
The enclosure and internal
parts are adequately fixed by
screws. Clearances and
creepage distances are never
reduced below the required
values as a result of wear.
Verdict
P
Clearances and creepage distances between live
The enclosure and internal
parts and accessible parts not reduced below values parts are adequately fixed by
for supplementary insulation, if wires, screws etc.
screws.
become loose
P
Supplementary and reinforced insulation designed or Constructed so that clearances
protected against deposition of dirt or dust
and creepage distances are
never reduced below the
required values due to
deposition of dirt or dust.
P
Supplementary insulation of natural or synthetic
rubber resistant to ageing, or arranged and
dimensioned so that creepage distances are not
reduced below values specified in 29.2
22.33
Result
No natural or synthetic rubber
for supplementary insulation.
N/A
Ceramic material not tightly sintered, similar material No ceramic material for
or beads alone not used as supplementary or
supplementary or reinforced
reinforced insulation
insulation.
N/A
Oxygen bomb test at 70 C for 96 h and 16 h at
room temperature
N/A
Insulating material in which heating conductors are
No heating conductors.
embedded considered to be basic insulation and not
reinforced insulation (IEC 60335-1/A2)
N/A
Conductive liquids that are or may become
accessible in normal use are not in direct contact
with live parts
N/A
No conductive liquids.
Electrodes not used for heating liquids
N/A
For class II constructions, conductive liquids that are
or may become accessible in normal use, not in
direct contact with basic or reinforced insulation
N/A
TRF No. IEC60335_2_40F
Page 34 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
For class II constructions, conductive liquids which
are in contact with live parts, not in direct contact
with reinforced insulation
Verdict
N/A
22.34
Shafts of operating knobs, handles, levers etc. not
live, unless the shaft is not accessible when the part
is removed
No such parts.
N/A
22.35
Handles, levers and knobs, held or actuated in
normal use, not becoming live in the event of a
failure of basic insulation (IEC 60335-1/A2)
No such parts.
N/A
Such parts being of metal, and their shafts or fixings
are likely to become live in the event of a failure of
basic insulation, they are either adequately covered
by insulation material, or their accessible parts are
separated from their shafts or fixings by
supplementary insulation (IEC 60335-1/A2)
N/A
Requirement does not apply to handles, levers and
knobs on stationary appliances other than those of
electrical components, provided they are either
reliably connected to an earthing terminal or earthing
contact, or separated from live parts by earthed
metal
N/A
22.36
Handles continuously held in the hand in normal use No such parts.
are so constructed that when gripped as in normal
use, the operators hand is not likely to touch metal
parts, unless they are separated from live parts by
double or reinforced insulation
N/A
22.37
Capacitors in class II appliances not connected to
accessible metal parts, unless complying with 22.42
N/A
Metal casings of capacitors in class II appliances
separated from accessible metal parts by
supplementary insulation, unless complying with
22.42
N/A
22.38
Capacitors not connected between the contacts of a
thermal cut-out
Not connected.
22.39
Lamp holders used only for the connection of lamps
No lamp holders.
22.40
Motor-operated appliances and combined
Fixed appliance.
appliances intended to be moved while in operation, No accessible moving parts.
or having accessible moving parts, fitted with a
switch to control the motor. The actuating member of
the switch being easily visible and accessible
N/A
Unless appliance can operate continuously,
automatically or remotely without giving rise to a
hazard, appliances for remote operation being fitted
with a switch. Actuating member of switch being
easily visible and accessible (IEC 60335-1/A2)
N/A
22.41
No components, other than lamps, containing
mercury
TRF No. IEC60335_2_40F
No components containing
mercury.
P
N/A
P
Page 35 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
22.42
Protective impedance consisting of at least two
separate components
N/A
Values specified in 8.1.4 not exceeded if any one of
the components are short-circuited or open-circuited
N/A
22.43
Appliances adjustable for different voltages,
accidental changing of the setting of the voltage
unlikely to occur
Not adjustable for different
voltages.
22.44
Appliances not have an enclosure shaped or
decorated like a toy (IEC 60335-1/A2)
The enclosure is not shaped or
decorated enough for children
not to treat it as a toy.
22.45
When air is used as reinforced insulation, clearances Air is not used as reinforced
not reduced below the values specified in 29.1.4 due insulation.
to deformation as a result of an external force
applied to the enclosure
N/A
22.46
Software used in protective electronic circuits is
software class B or C (IEC 60335-1/A1):
Not considered.
N/A
22.47
Appliances connected to the water mains withstand
the water pressure expected in normal use
(IEC 60335-1/A1)
Not intended to be connected
to the water mains.
N/A
No leakage from any part, including any inlet water
hose (IEC 60335-1/A1)
N/A
P
N/A
22.48
Appliances connected to the water mains
constructed to prevent backsiphonage of
non-potable water (IEC 60335-1/A1)
22.49
Remote operation duration of operation set before
appliance can be started, unless (IEC 60335-1/A2)
N/A
appliance switches off automatically or can operate
continuously without hazard (IEC 60335-1/A2)
N/A
22.50
Controls incorporated in appliance take priority over
controls actuated by remote operation
(IEC 60335-1/A2)
N/A
22.51
Control on appliance being manually adjusted to
setting for remote operation before appliance can be
operated in this mode (IEC 60335-1/A2)
N/A
Visual indication showing that appliance is adjusted
for remote operation (IEC 60335-1/A2)
N/A
Not intended to be connected
to the water mains.
Manual setting and visual indication not necessary on appliances that can operate as
follows, without giving rise to a hazard (IEC 60335-1/A2):
22.52
N/A
—
- operate continuously (IEC 60335-1/A2),
N/A
- operate automatically, or (IEC 60335-1/A2)
N/A
- be operated remotely (IEC 60335-1/A2)
N/A
Socket-outlets on appliances accessible to user in
accordance with socket-outlet system used in
country where appliance sold (IEC 60335-1/A2)
TRF No. IEC60335_2_40F
No socket-outlets.
N/A
Page 36 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
22.101
Appliances intended to be fixed, securely fixed
(IEC 60335-2-40)
Securely fixed.
22.102.1
At least two thermal cut-outs in appliances with
supplementary heating elements for air (first one be
self-resetting and other non-self-resetting thermal
cut-out) (IEC 60335-2-40/A2)
No supplementary heating
elements.
N/A
22.102.2
Appliances provided with supplementary heaters for
water incorporate non-self-resetting thermal cut-out,
providing all-pole disconnection that operates
separately from water thermostats
(IEC 60335-2-40/A2)
No supplementary heaters.
N/A
However, for appliances intended to be connected to
fixed wiring, the neutral conductor need not be
disconnected (IEC 60335-2-40/A2)
22.102.3
Thermal cut-outs of capillary type open in event of
leakage from capillary tube (IEC 60335-2-40/A2)
22.103
Non-self-resetting cut-outs independent of other
control devices (IEC 60335-2-40)
22.104
Containers of sanitary hot water heat pumps
withstand twice permissible operating pressure in
closed containers (IEC 60335-2-40) or
Verdict
P
N/A
No supplementary heaters.
N/A
N/A
No sanitary hot water heat
pumps.
N/A
0,15 MPa in open containers (IEC 60335-2-40)
N/A
without leakage or rupture (IEC 60335-2-40)
N/A
22.105
Air or vapour cushion in closed containers not
exceeding 10 % (IEC 60335-2-40)
Not provided.
N/A
22.106
Pressure relief devices operating at 0,1 MPa over
permissible operating pressure (IEC 60335-2-40)
Not provided.
N/A
22.107
Water outlet systems of open containers free from
Not provided.
obstruction causing over-pressure (IEC 60335-2-40)
N/A
Vented containers of sanitary hot water heat pumps
always open to the atmosphere through appropriate
aperture (IEC 60335-2-40)
N/A
Not vented open containers subjected to test in
No sanitary hot water heat
accordance with clause 22.104 to vacuum of 33 kPa pumps.
for 15 min (IEC 60335-2-40)
N/A
Container shiw no deformation which result in a
hazard (IEC 60335-2-40)
N/A
22.108
22.109
Replacement of non-self-resetting thermal cut-outs
does not damage other connections
(IEC 60335-2-40)
No non-self-resetting thermal
cut-outs.
N/A
22.110
Non-self-resetting thermal cut-outs operate without
short-circuiting live parts of different potential and
without causing contact between live parts and
enclosure (IEC 60335-2-40)
No non-self-resetting thermal
cut-outs.
N/A
Test repeated five times without blowing 3 A fuse
which connects appliance to earth (IEC 60335-2-40)
TRF No. IEC60335_2_40F
N/A
Page 37 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
Electric strength test as specified in clause 16.3 for
supplementary heating elements (IEC 60335-2-40)
N/A
22.111
Manual resetting of thermostats not necessary after
power supply interruption (IEC 60335-2-40)
N/A
22.112
Construction of refrigerating system comply with
requirements of Section 3 of ISO 5149
(IEC 60335-2-40/A1)
Complied with relevant
requirements.
22.113
Flammable refrigerant used, refrigerant tubing
protected or enclosed to avoid mechanical damage
(IEC 60335-2-40/A1)
Intended for the use of a nonflammable refrigerant.
P
N/A
Tubing protected to extent that it will not be handled
or used for carrying during moving of product
(IEC 60335-2-40/A1)
N/A
Tubing located within confines of cabinet considered
to be protected from mechanical damage
(IEC 60335-2-40/A1)
N/A
22.114
Flammable refrigerant used, low temperature solder
alloys, such as lead/tin alloys, not acceptable for
pipe connections (IEC 60335-2-40/A1)
Intended for the use of a nonflammable refrigerant.
N/A
22.115
Total refrigerant mass (M) of all refrigerating systems Intended for the use of a nonwithin appliance employing flammable refrigerants,
flammable refrigerant.
not exceed m3 defined in annex GG
(IEC 60335-2-40/A1)
N/A
22.116
Appliances using flammable refrigerants constructed Intended for the use of a nonthat any leaked refrigerant not flow or stagnate so as flammable refrigerant.
to cause fire or explosion hazard in areas within
appliance where electrical components, which could
be a source of ignition and which could function
under normal conditions or in event of leak, fitted
(IEC 60335-2-40/A1)
N/A
Separate components, such as thermostats, which
charged with less than 0,5 g of flammable gas not
considered to cause fire or explosion hazard in event
of leakage of gas within component itself
(IEC 60335-2-40/A1)
N/A
All electrical components that could be a source of ignition and which could function
under normal conditions or in the event of a leak, comply with one of the following
(IEC 60335-2-40/A1):
—
- IEC 60079-15:2001, Cl. 9 to 26, for group IIA gases Intended for the use of a nonor the refrigerant used or an applicable standard
flammable refrigerant.
that makes electrical components suitable for use
in Zone 2, 1 or 0 as defined in IEC 60079-14
(IEC 60335-2-40/A1)
N/A
- Not be located in an area where a potentially
flammable gas mixture will accumulate as
demonstrated by the test of annex FF
(IEC 60335-2-40/A1)
N/A
TRF No. IEC60335_2_40F
Page 38 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
- Be located in an enclosure. The enclosure
containing the electrical components comply with
IEC 60079-15:2001 for enclosures suitable for use
with group IIA gases or the refrigerant used
(IEC 60335-2-40/A1)
Verdict
N/A
22.117
Temperatures on surfaces that exposed to leakage
of flammable refrigerants not exceed auto-ignition
temperature of refrigerant reduced by 100 K; some
typical values given in annex BB
(IEC 60335-2-40/A1)
Intended for the use of a nonflammable refrigerant.
N/A
22.118
Flammable refrigerant used, all appliances charged Intended for the use of a nonwith refrigerant at manufacturing location or charged flammable refrigerant.
on site as recommended by manufacturer
(IEC 60335-2-40/A1)
N/A
Part of appliance that charged on site, which requires brazing or welding in installation
not shipped with flammable refrigerant charge. Joints made in installation between
parts of refrigerating system, with at least one part charged, made in accordance with
following (IEC 60335-2-40/A1):
—
- A brazed, welded, or mechanical connection shall
be made before opening the valves to permit
refrigerant to flow between the refrigerating system
parts. A vacuum valve shall be provided to
evacuate the interconnecting pipe and/or any
uncharged refrigerating system part
(IEC 60335-2-40/A1)
N/A
- Reusable mechanical connectors and flared joints
are not allowed indoors (IEC 60335-2-40/A1)
N/A
- Refrigerant tubing shall be protected or enclosed to
avoid damage (IEC 60335-2-40/A1)
N/A
Flexible refrigerant connectors (such as connecting
lines between the indoor and outdoor unit) that may
be displaced during normal operations shall be
protected against mechanical damage
(IEC 60335-2-40/A1)
N/A
—
23
INTERNAL WIRING
23.1
Wireways smooth and free from sharp edges
Wireways are smooth and free
from sharp edges.
P
Wires protected against contact with burrs, cooling
fins etc.
Wires not in contact with
cooling fins.
P
Wire holes in metal well rounded or provided with
bushings
Well rounded.
P
Wiring effectively prevented from coming into contact Effectively prevented from
with moving parts
coming into contact with
moving parts
TRF No. IEC60335_2_40F
P
Page 39 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
23.2
Beads etc. on live wires cannot change their
position, and are not resting on sharp edges or
corners
No beads.
Beads inside flexible metal conduits contained within
an insulating sleeve
23.3
Verdict
N/A
N/A
Electrical connections and internal conductors
movable relatively to each other not exposed to
undue stress
Not cause undue stress.
P
Flexible metallic tubes not causing damage to
insulation of conductors
No flexible metallic tubes.
N/A
Open-coil springs not used
Not used.
P
Adequate insulating lining provided inside a coiled
spring, the turns of which touch one another
N/A
No damage after 10 000 flexings for conductors
flexed during normal use or 100 flexings for
conductors flexed during user maintenance
N/A
Electric strength test, 1000 V between live parts and
accessible metal parts
N/A
23.4
Bare internal wiring sufficiently rigid and fixed
No bare internal wiring.
23.5
The insulation of internal wiring withstanding the
electrical stress likely to occur in normal use
The insulation of internal wiring
withstands the electrical stress
likely to occur in normal use.
P
No breakdown when a voltage of 2000 V is applied
for 15 min between the conductor and metal foil
wrapped around the insulation
No breakdown.
P
N/A
23.6
Sleeving used as supplementary insulation on
Adequately secured by tieinternal wiring retained in position by positive means bands.
P
23.7
The colour combination green/yellow used only for
earthing conductors
Earthing conductor is colored
green/yellow.
P
23.8
Aluminium wires not used for internal wiring
No aluminium wires.
23.9
No lead-tin soldering of stranded conductors where
they are subject to contact pressure, unless
Connectors are provided.
clamping means so constructed that there is no risk
of bad contact due to cold flow of the solder
23.10
The insulation and sheath of internal wiring,
incorporated in external hoses for the connection of
an appliance to the water mains, at least equivalent
to that of light polyvinyl chloride sheathed flexible
cord (60227 IEC 52) (IEC 60335-1/A1)
24
COMPONENTS
24.1
Components comply with safety requirements in
relevant IEC standards
TRF No. IEC60335_2_40F
N/A
P
N/A
Not intended to be connected
to the water mains.
N/A
—
Complying with IEC or
equivalent standards.
P
Page 40 of 97
Report No. 236145
IEC 60335-2-40
Clause
24.1.1
Requirement – Test
Result
List of components
(See appended table)
—
Components not tested and found to comply with
Complying with IEC or
relevant IEC standard for number of cycles specified, equivalent standards.
tested in accordance with clause 24.1.1 to 24.1.9
(IEC 60335-1/A2)
P
Components not tested and found to comply with
relevant IEC standard, components not marked or
not used in accordance with its marking, tested
under the conditions occurring in the appliance
P
Complying with IEC or
equivalent standards.
Lampholders and starterholders not being tested and No such components.
found to comply with relevant IEC standard, tested
as a part of appliance and additionally according to
gauging and interchangeability requirements of
relevant IEC standard (IEC 60335-1/A2)
N/A
Motor-compressors not tested according to
IEC 60335-2-34 (not necessary to meet all
requirements of IEC 60335-2-34) (IEC 60335-2-40)
Not checked in the appliance.
N/A
Capacitors likely to be permanently subjected to the
supply voltage and used for radio interference
suppression or for voltage dividing, complying with
IEC 60384-14, or
Complying with IEC 60384-14.
P
tested according to annex F
24.1.2
24.1.3
24.1.4
Verdict
Safety isolating transformers complying with
IEC 61558-2-6, or
N/A
No such safety isolating
transformer.
N/A
tested according to annex G
N/A
Switches complying with IEC 61058-1, the number of No such switches.
cycles of operation being at least
10 000, or
N/A
tested according to annex H
N/A
If the switch operates a relay or contactor, the
complete switching system is subjected to the test
N/A
Automatic controls complying with IEC 60730-1 with relevant part 2. The number of
cycles of operation being:
—
- thermostats: ................................................. 10 000
N/A
- temperature limiters: ...................................... 1000
N/A
- self-resetting thermal cut-outs (IEC 60335-2-40):
........................................................................ 3000
N/A
- voltage maintained non-self-resetting thermal
cut-outs: .......................................................... 1000
N/A
- other non-self-resetting thermal cut-outs
(IEC 60335-2-40): ............................................ 300
N/A
- timers: ............................................................. 3000
N/A
- energy regulators: ....................................... 10 000
N/A
TRF No. IEC60335_2_40F
Page 41 of 97
Report No. 236145
IEC 60335-2-40
Clause
24.1.5
Requirement – Test
Result
Verdict
- thermostats which control motor-compressor
(IEC 60335-2-40): ..................................... 100 000
N/A
- motor-compressor starting relays (IEC 60335-2-40):
................................................................... 100 000
N/A
- automatic thermal motor-protectors for hermetic
and semi-hermetic type motor-compressors (not
less than number of operations during locked rotor
test) (IEC 60335-2-40): ........................... min 2000
N/A
- manual reset thermal motor-protectors for hermetic
and semi-hermetic type motor-compressors
(IEC 60335-2-40): .............................................. 50
N/A
- other automatic thermal motor-protectors
(IEC 60335-2-40): .......................................... 2000
N/A
- other manual reset thermal motor-protectors
(IEC 60335-2-40): .............................................. 30
N/A
Thermal motor protectors are tested in combination
with their motor under the conditions specified in
annex D (IEC 60335-1/A1)
N/A
For water valves containing live parts and that are
incorporated in external hoses for connection of an
appliance to the water mains, the degree of
protection declared for subclause 6.5.2 of
IEC 60730-2-8 is IPX7 (IEC 60335-1/A1)
Not intended to be connected
to the water mains.
N/A
Appliance couplers complying with IEC 60320-1
No appliance couplers.
N/A
However, appliances classified higher than IPX0, the
appliance couplers complying with IEC 60320-2-3
(IEC 60335-1/A1)
N/A
Interconnection couplers complying with
IEC 60320-2-2
N/A
24.1.6
Small lamp holders similar to E10 lampholders
No lamp holders.
complying with IEC 60238, the requirements for E10
lampholders being applicable
N/A
24.1.7
Remote operation of appliance via
telecommunication network, relevant standard for
telecommunication interface circuitry in appliance is
IEC 62151 (IEC 60335-1/A2)
No such remote operation.
N/A
24.1.8
Standard for thermal links IEC 60691
(IEC 60335-1/A2)
Incorporated with terminal
block.
Complying with IEC 60691.
P
Thermal links not complying with IEC 60691
considered to be an intentionally weak part for
purposes of clause 19 (IEC 60335-1/A2)
24.1.9
Relays, other than motor starting relays, tested as
part of appliance (IEC 60335-1/A2)
TRF No. IEC60335_2_40F
N/A
Approved relays are used.
Checked in the appliance.
P
Page 42 of 97
Report No. 236145
IEC 60335-2-40
Clause
24.2
Requirement – Test
Result
Verdict
They also tested in accordance with clause 17 of
IEC 60730-1, number of operations in clause 24.1.4
selected according to relay function in the appliance
(IEC 60335-1/A2) .....................................................:
Approved relays are used.
Checked in the appliance.
P
No switches or automatic controls in flexible cords
No such components.
P
No devices causing the protective device in the fixed No such devices.
wiring to operate in the event of a fault in the
appliance
P
No thermal cut-outs that can be reset by soldering
No such components.
P
24.3
Switches intended for all-pole disconnection of
stationary appliances are directly connected to the
supply terminals and having a contact separation in
all poles, providing full disconnection under
overvoltage category III conditions
No such components.
N/A
24.4
Plugs and socket-outlets for extra-low voltage
Not applicable.
circuits and heating elements, not interchangeable
with plugs and socket-outlets listed in IEC 60083 or
IEC 60906-1 or with connectors and appliance inlets
complying with the standard sheets of IEC 60320-1
N/A
24.5
Capacitors in auxiliary windings of motors marked
with their rated voltage and capacitance and used
accordingly
N/A
24.6
Brushless DC type of fan
motor.
No auxiliary capacitors.
Voltage across capacitors in series with a motor
winding does not exceed 1,1 times rated voltage,
when the appliance is supplied at 1,1 times rated
voltage under minimum load
N/A
Working voltage of motors connected to the supply
No such motors.
mains and having basic insulation that is inadequate
for the rated voltage of the appliance, not exceeding
42 V
N/A
In addition, the motors are complying with the
requirements of annex I
N/A
24.7
Hose-sets for connection of appliances to the water
mains, complying with IEC 61770 and supplied with
the appliance (IEC 60335-1/A1)
Not intended to be connected
to the water mains.
N/A
24.101
Replaceable parts of thermal control devices
identified by marking (IEC 60335-2-40)
Not considered.
N/A
TRF No. IEC60335_2_40F
Page 43 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
25
SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS
—
25.1
Appliance not intended for permanent connection to fixed wiring, means for
connection to the supply:
—
- supply cord fitted with a plug
P
1. Not checked in this test
report.
Verdict
2. The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord referring to an installation
manual.
- an appliance inlet having at least the same degree
of protection against moisture as required for
appliance
N/A
- pins for insertion into socket-outlets
N/A
Supply cord fitted with plug provided, if (IEC 60335-2-40):
25.2
25.3
—
- appliance only for indoor use (IEC 60335-2-40),
N/A
- marked with rating of 25 A or less and
(IEC 60335-2-40)
N/A
- complies with code requirements of country where
it will be used (IEC 60335-2-40).
N/A
Appliance inlet not allowed (IEC 60335-2-40)
N/A
Appliance not provided with more than one means of
connection to the supply mains
P
Stationary appliance for multiple supply may be
provided with more than one means of connection,
provided electric strength test of 1250 V for 1 min
between each means of connection causes no
breakdown
N/A
Connection of supply conductors for appliance
intended to be permanently connected to fixed wiring
possible after the appliance has been fixed to its
support
N/A
Appliance provided with a set of terminals for the
connection of cables or fixed wiring, cross-sectional
areas specified in 26.6
N/A
Appliance provided with a set of terminals allowing
the connection of a flexible cord
N/A
Appliance provided with a set of supply leads
accommodated in a suitable compartment
N/A
Appliance provided with a set of terminals and cable
entries, conduit entries, knock-outs or glands,
allowing connection of appropriate type of cable or
conduit
N/A
TRF No. IEC60335_2_40F
Page 44 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
25.4
Cable and conduit entries, rated current of appliance
not exceeding 16 A, dimensions according to
table 10
N/A
Introduction of conduit or cable does not reduce
clearances or creepage distances below values
specified in 29
N/A
25.5
Result
Method for assemble supply cord with the appliance:
—
- type X attachment
- type Y attachment
Verdict
N/A
Type Y attachment.
P
- type Z attachment, if allowed in part 2
N/A
Type X attachment, other than those with a specially Type Y attachment.
prepared cord, not used for flat twin tinsel cords
N/A
25.6
Plugs fitted with only one flexible cord
N/A
25.7
Supply cords being one of the following types (IEC 60335-1/A2):
No plugs provided with.
—
- rubber sheathed (at least 60245 IEC 53)
(IEC 60335-1/A2)
N/A
- polychloroprene sheathed (at least 60245 IEC 57)
(IEC 60335-1/A2)
N/A
- cross-linked polyvinyl chloride sheathed (at least
60245 IEC 87) (IEC 60335-1/A2)
N/A
Polyvinyl chloride sheathed:
Not used if they are likely to touch metal parts having a temperature rise exceeding
75 K during clause 11 (IEC 60335-1/A2)
—
- light polyvinyl chloride sheathed cord (at least
60227 IEC 52), appliances not exceeding 3 kg
(IEC 60335-1/A2)
N/A
- ordinary polyvinyl chloride sheathed cord (at least
60227 IEC 53), other appliances (IEC 60335-1/A2)
N/A
Heat resistant polyvinyl chloride sheathed:
Not used for type X attachment other than specially prepared cords
(IEC 60335-1/A2):
—
- heat-resistant light polyvinyl chloride sheathed cord
(at least 60227 IEC 56), appliances not exceeding
3 kg (IEC 60335-1/A2)
N/A
- heat-resistant polyvinyl chloride sheathed cord
(60227 IEC 57), other appliances (IEC 60335-1/A2)
N/A
Supply cords for outdoor use not lighter than
polychloroprene sheathed flexible cord
(60245 IEC 57) (IEC 60335-2-40)
TRF No. IEC60335_2_40F
Interconnection cord for
connecting the indoor unit into
the outdoor unit.
Not lighter than the code
designation as following;
60245 IEC 57 (IEC)
H05RN-F (CENELEC)
P
Page 45 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
25.8
Nominal cross-sectional area of supply cords
according to table 11; rated current (A);
cross-sectional area (mm²) ......................................:
The manufacturer, service
agent or similarly qualified
person should use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
It can be variable with the
user’s selection of combination
of outdoor unit with indoor unit.
25.9
Supply cord not in contact with sharp points or edges No contacts.
P
25.10
Green/yellow core for earthing purposes in class I
appliance
P
25.11
Conductors of supply cords not consolidated by
lead-tin soldering where they are subject to contact
pressure, unless
N/A
clamping means so constructed that there is no risk
of bad contacts due to cold flow of the solder
N/A
25.12
Moulding the cord to part of the enclosure does not
damage the insulation of the supply cord
N/A
25.13
Inlet opening so shaped as to prevent damage to the Well rounded.
supply cord
25.14
Protective earthing conductor
is colored green/yellow.
Verdict
P
P
Unless the enclosure at the inlet opening is of
insulation material, a non-detachable lining or
bushing complying with clause 29.3 for
supplementary insulation provided
N/A
If unsheathed supply cord, a similar additional
bushing or lining is required, unless
N/A
the appliance is class 0
N/A
Supply cords adequately protected against
excessive flexing
N/A
Flexing test:
—
- applied force (N) .....................................................:
N/A
- number of flexings ..................................................:
N/A
The test does not result in:
—
- short circuit between the conductors
N/A
- breakage of more than 10 % of the strands of any
conductor
N/A
- separation of the conductor from its terminal
N/A
- loosening of any cord guard
N/A
- damage, within the meaning of the standard, to the
cord or the cord guard
N/A
TRF No. IEC60335_2_40F
Page 46 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
- broken strands piercing the insulation and
becoming accessible
25.15
25.16
Conductors of the supply cord relieved from strain,
twisting and abrasion by use of cord anchorage
Verdict
N/A
Adequate cord anchorages are
used.
P
The cord cannot be pushed into the appliance to
such an extent that the cord or internal parts of the
appliance can be damaged
P
Pull and torque test of supply cord, values shown in Pull force: 100 N
table 12: pull (N); torque (not on automatic cord reel) Torque: 0,35 Nm
(Nm) ..........................................................................:
P
Max. 2 mm displacement of cord
Less than the value specified.
P
Creepage distances and clearances not reduced
below values specified in clause 29.1
Not reduced.
P
Cord anchorages for type X attachments constructed and located so that:
- replacement of the cord is easily possible
Type Y attachment.
—
N/A
- it is clear how the relief from strain and the
prevention of twisting are obtained
N/A
- they are suitable for different types of cord
N/A
- cord cannot touch the clamping screws of cord
anchorage if these screws are accessible, unless
separated from accessible metal parts by
supplementary insulation
N/A
- the cord is not clamped by a metal screw which
bears directly on the cord
N/A
- at least one part of the cord anchorage securely
fixed to the appliance, unless part of a specially
prepared cord
N/A
- screws which have to be operated when replacing
the cord do not fix any other component, if
applicable
N/A
- if labyrinths can be bypassed the test of 25.15 is
nevertheless withstood
N/A
- for class 0, 0I and I appliances: they are of
insulating material or are provided with an
insulating lining, unless a failure of the insulation of
the cord does not make accessible metal parts live
N/A
- for class II appliances: they are of insulating
material, or if of metal, they are insulated from
accessible metal parts by supplementary insulation
N/A
Conductors not moved more than 1 mm in terminals
N/A
25.17
Adequate cord anchorages for type Y and Z
attachment
Type Y attachment.
P
25.18
Cord anchorages only accessible with the aid of a
tool, or
Accessible with a tool only.
P
TRF No. IEC60335_2_40F
Page 47 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
so constructed that the cord can only be fitted with
the aid of a tool
25.19
Type X attachment, glands not used as cord
anchorage in portable appliances
Verdict
P
Type Y attachment.
Tying the cord into a knot or tying the cord with string
not used
N/A
N/A
25.20
Conductors of the supply cord for type Y and Z
attachment adequately additionally insulated
Type Y attachment.
P
25.21
Space for supply cord for type X attachment or for
connection of fixed wiring constructed to permit
checking of conductors with respect to correct
positioning and connection before fitting any cover,
no risk of damage to the conductors when fitting the
cover, no contact with accessible metal parts if a
conductor becomes loose, etc.
Type Y attachment.
N/A
For portable appliances, the uninsulated end of a
conductor prevented from any contact with
accessible metal parts, unless the end of the cord is
such that the conductors are unlikely to slip free
Stationary appliance.
N/A
Interconnection cords comply with the requirements
for the supply cord, except as specified
1. Not checked in this test
report.
25.23
P
2. The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
If necessary, electric strength test of clause 16.3
N/A
25.24
Interconnection cords not detachable without the aid Detachable with a tool only.
of a tool if compliance with the standard is impaired
when they are disconnected
25.25
Dimensions of pins compatible with the dimensions
of the relevant socket-outlet. Dimensions of pins and
engagement face in accordance with the relevant
plug in IEC 60083
26
TERMINALS FOR EXTERNAL CONDUCTORS
—
26.1
Appliances provided with terminals or equally
effective devices for connection of external
conductors
P
Terminals only accessible after removal of a
non-detachable cover
N/A
Accessible after the cover
detached with a tool.
However, earthing terminals may be accessible if a Earthing terminal of indoor unit.
tool is required to make the connections and means
are provided to clamp the wire independently from its
connection (IEC 60335-1/A1)
TRF No. IEC60335_2_40F
P
P
P
Page 48 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
26.2
Appliances with type X attachment and appliances
Type Y attachment.
for connection to fixed wiring provided with terminals
in which connections are made by means of screws,
nuts or similar devices, unless the connections are
soldered
N/A
Screws and nuts serve only to clamp supply
conductors, except
N/A
internal conductors, if so arranged that they are
unlikely to be displaced when fitting the supply
conductors
N/A
If soldered connections used, the conductor so
positioned or fixed that reliance is not placed on
soldering alone
N/A
Soldering alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free at the soldered joint
N/A
26.3
Terminals for type X attachment and for connection
to fixed wiring so constructed that the conductor is
clamped between metal surfaces with sufficient
contact pressure and without damaging the
conductor
Result
Type Y attachment.
Terminals for type X attachment and those for connection to fixed wiring so fixed that
when tightening or loosening the clamping means:
Verdict
N/A
—
- the terminal does not loosen
N/A
- internal wiring is not subjected to stress
N/A
- clearances and creepage distances are not
reduced below the values in 29
N/A
Compliance checked by inspection and by the test of
subclause 9.6 of IEC 60999-1, torque applied being
equal to two-thirds of torque specified. Nominal
diameter of thread (mm); screw category; torque
(Nm) (IEC 60335-1/A2) ............................................:
N/A
26.4
Terminals for type X attachment, except those with a Type Y attachment.
specially prepared cord, and those for connection to
fixed wiring, no special preparation of conductors
required, and so constructed or placed that
conductors prevented from slipping out
N/A
26.5
Terminals for type X attachment so located or
shielded that if a wire of a stranded conductor
escapes, no risk of accidental connection to other
parts that result in a hazard
N/A
Type Y attachment.
Stranded conductor test, 8 mm insulation removed
N/A
No contact between live parts and accessible metal
parts and, for class II constructions, between live
parts and metal parts separated from accessible
metal parts by supplementary insulation only
N/A
TRF No. IEC60335_2_40F
Page 49 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
26.6
Terminals for type X attachment and for connection
to fixed wiring suitable for connection of conductors
with required cross-sectional area according to
table 13; rated current (A); nominal cross-sectional
area (mm²) (IEC 60335-1/A2) ..................................:
Type Y attachment.
Terminals only suitable for a specially prepared cord
Verdict
N/A
N/A
26.7
Terminals for type X attachment accessible after
removal of a cover or part of the enclosure
26.8
Terminals for the connection to fixed wiring, including Not a permanently connected
the earthing terminal, located close to each other
appliance.
N/A
26.9
Terminals of the pillar type constructed and located
as specified
No such terminal.
N/A
26.10
Terminals with screw clamping and screwless
terminals not used for flat twin tinsel cords, unless
conductors ends fitted with a device suitable for
screw terminals
Not used.
N/A
Type Y attachment.
Pull test of 5 N to the connection
26.11
For type Y and Z attachment: soldered, welded,
crimped and similar connections may be used
N/A
N/A
Type Y attachment.
P
For class II appliances: the conductor so positioned
or fixed that reliance is not placed on soldering,
welding or crimping alone
N/A
For class II appliances: soldering, welding or
crimping alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free
N/A
—
27
PROVISION FOR EARTHING
27.1
Accessible metal parts of class 0I and I appliances,
permanently and reliably connected to an earthing
terminal or contact of the appliance inlet
Earthing terminal is reliably
fixed with a screw having a
washer on a metal part.
P
Earthing terminals not connected to neutral terminal
Not connected to neutral
terminal.
P
Class 0, II and III appliance have no provision for
earthing
Class I appliance.
Safety extra-low voltage circuits not earthed, unless
protective extra-low voltage circuits
Not earthed.
P
Clamping means adequately secured against
accidental loosening
Adequately secured against
accidental loosening.
P
27.2
N/A
Terminals used for the connection of external
equipotential bonding conductors allow connection of
conductors of 2,5 to 6 mm², and
N/A
do not provide earthing continuity between different
parts of the appliance
N/A
TRF No. IEC60335_2_40F
Page 50 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Conductors cannot be loosened without the aid of a
tool
27.3
For detachable parts that are plugged into another
part of the appliance, and having an earth
connection, the earth connection made before and
separated after current-carrying connections when
removing the part (IEC 60335-1/A1)
P
Not such construction.
For appliances with supply cord, current-carrying
conductors become taut before earthing conductor, if
the cord slips out of the cord anchorage
27.4
P
All parts have adequate
protection against corrosion.
P
Adequate resistance to corrosion of coated or
uncoated parts providing earthing continuity, other
than parts of a metal frame or enclosure
Adequately protected against
corrosion.
P
Parts of steel providing earthing continuity provided
at the essential areas with an electroplated coating,
thickness at least 5 m
P
Adequate protection against rusting of parts of
coated or uncoated steel, only intended to provide or
transmit contact pressure
P
No aluminium alloy.
Low resistance of connection between earthing
terminal and earthed metal parts
Resistance not exceeding 0,1 Ω at the specified
low-resistance test
N/A
P
This requirement does not apply to connections
providing earthing continuity in the protective
extra-low voltage circuit, provided that clearances of
basic insulation are based on the rated voltage of the
appliance
27.6
N/A
No risk of corrosion resulting from contact between
metal of earthing terminal and other metal
In case of aluminium alloys precautions taken to
avoid risk of corrosion
27.5
Verdict
N/A
Applied current: 25A
Measured resistance; 0.02 Ω
(PE of indoor unit to the
accessible metal part of
outdoor unit)
It shall be checked with an
appliance connecting the
indoor unit with the outdoor
unit again, if the value of 1,5
times rated current is greater
than 25A.
P
Printed conductors of printed circuit boards not used Stationary appliance.
to provide earthing continuity in hand held
appliances (IEC 60335-1/A2)
N/A
In other appliance provide earthing continuity, if at
least two tracks used with independent soldering
points and appliance complies with requirements of
clause 27.5 for each circuit (IEC 60335-1/A2)
N/A
TRF No. IEC60335_2_40F
Page 51 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
28
SCREWS AND CONNECTIONS
28.1
Fixings, electrical connections and connections
providing earthing continuity withstand mechanical
stresses
Result
—
Connections are adequately
fixed and expected to
withstand the mechanical
stress occurring in normal use.
Screws not of soft metal liable to creep, such as zinc No screws of soft metal liable
or aluminium
to creep.
Diameter of screws of insulating material min. 3 mm
28.2
P
P
N/A
Screws of insulating material not used for any
electrical connection or connections providing
earthing continuity
No screws of insulating
material.
Screws used for electrical connections or
connections providing earthing continuity screw into
metal
Screws used for electrical
connections or connections
providing earthing continuity
are of metal.
N/A
P
Screws not of insulating material if their replacement No screws of insulating
by a metal screw can impair supplementary or
material.
reinforced insulation
N/A
Type X attachment, screws to be removed for
Type Y attachment.
replacement of supply cord or for user maintenance,
not of insulating material if their replacement by a
metal screw can impair basic insulation
N/A
For screws and nuts; test as specified
(IEC 60335-1/A2)
(See appended table)
P
Electrical connections and connections providing
earthing continuity constructed so that contact
pressure not transmitted through insulating material
liable to shrink or distort, unless shrinkage or
distortion compensated
Constructed so that contact
pressure is not transmitted
through insulating material.
P
This requirement does not apply to electrical
connections in circuits carrying a current not
exceeding 0,5 A
28.3
Verdict
P
Space-threaded (sheet metal) screws only used for
electrical connections if they clamp the parts
together
N/A
Thread-cutting (self-tapping) screws and thread
rolling screws only used for electrical connections if
they generate a full form standard machine screw
thread (IEC 60335-1/A2)
N/A
However, thread-cutting (self-tapping) screws not
used if they likely to be operated by user or installer
(IEC 60335-1/A2)
TRF No. IEC60335_2_40F
Not intended to be operated by
users.
N/A
Page 52 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Thread-cutting, thread rolling and space threaded screws may be used in connections
providing earthing continuity provided it is not necessary to disturb connection
(IEC 60335-1/A2):
—
- in normal use (IEC 60335-1/A2),
P
- during user maintenance (IEC 60335-1/A2),
P
- when replacing a supply cord having a type X
attachment, or (IEC 60335-1/A2)
Type Y attachment.
- during installation (IEC 60335-1/A2)
At least two screws being used for each connection
providing earthing continuity, unless
(IEC 60335-1/A2)
29
Used not less than two screws.
P
N/A
Screws and nuts that make mechanical connection
secured against loosening if they also make
electrical connections or connections providing
earthing continuity
Spring washers are provided
against loosing for the earthing
connection.
Rivets for electrical connections or connections
providing earthing continuity secured against
loosening if subjected to torsion
No rivets.
P
N/A
CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION
—
Clearances, creepage distances and solid insulation Adequate to withstand
withstand electrical stress
electrical stresses.
P
Coatings used on printed circuits boards to protect
microenvironment (Type 1 coating) or
(IEC 60335-1/A2)
No coatings on PCBs.
N/A
to provide basic insulation (Type 2 coating), annex J
applies (IEC 60335-1/A2)
N/A
Microenvironment is pollution degree 1 under Type 1
coating (IEC 60335-1/A2)
N/A
No clearance or creepage distance requirements
under Type 2 coating (IEC 60335-1/A2)
N/A
For motor-compressor complies with
IEC 60335-2-34, parts related not checked
(IEC 60335-2-40)
For motor-compressor not complying with
IEC 60335-2-34, additions and modifications as
specified (IEC 60335-2-40)
29.1
N/A
P
screw forms a thread having a length of at least half
diameter of screw (IEC 60335-1/A2)
28.4
Verdict
Clearances not less than the values specified in
table 16, taking into account the rated impulse
voltage for overvoltage categories of table 15, unless
(IEC 60335-1/A1)
TRF No. IEC60335_2_40F
Not checked in the appliance.
N/A
N/A
P
Page 53 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
for basic insulation and functional insulation, they
comply with the impulse voltage test of clause 14
(IEC 60335-1/A1)
However, if construction is affected by wear,
distortion, movement of the parts or during
assembly, the clearances for rated impulse voltages
of 1 500 V and above are increased by 0,5 mm and
the impulse voltage test is not applicable
(IEC 60335-1/A1)
N/A
Not applicable.
Impulse voltage test not applicable (IEC 60335-1/A1):
29.1.1
Verdict
N/A
—
- when the microenvironment is pollution degree 3
(IEC 60335-1/A1)
Pollution degree 2.
N/A
- for basic insulation of class 0 and class 0I
appliances (IEC 60335-1/A1)
Class I appliance.
N/A
Appliances are in overvoltage category II
Overvoltage category II.
P
Compliance is checked by inspection and
measurements as specified
(See appended table)
P
Clearances of basic insulation withstand the
overvoltages, taking into account the rated impulse
voltage
P
Clearance at the terminals of tubular sheathed
heating elements may be reduced to 1 mm if the
microenvironment is pollution degree 1
No tubular sheathed heating
elements.
N/A
Lacquered conductors of windings considered to be
bare conductors (IEC 60335-1/A1)
Considered bare conductors.
P
29.1.2
Clearances of supplementary insulation not less than
those specified for basic insulation in table 16
P
29.1.3
Clearances of reinforced insulation not less than
those specified for basic insulation in table 16, but
using the next higher step for rated impulse voltage
P
29.1.4
For functional insulation, the values of table 16 are
applicable, unless
P
the appliance complies with clause 19 with the
functional insulation short-circuited
N/A
Lacquered conductors of windings considered to be
bare conductors (IEC 60335-1/A1)
P
However, clearances at crossover points are not
measured
Clearance between surfaces of PTC heating
elements may be reduced to 1 mm
Lacquered conductors of windings assumed to be
bare conductors, but the clearances specified in
table 16 are reduced by 0,5 mm for rated impulse
voltages of at least 1500 V
TRF No. IEC60335_2_40F
N/A
No PTC heating elements.
N/A
N/A
Page 54 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
29.1.5
Appliances having higher working voltage than rated
voltage, the voltage used for determining clearances
from table 16 is the sum of the rated impulse voltage
and the difference between the peak value of the
working voltage and the peak value of the rated
voltage
N/A
If the secondary winding of a step-down transformer
is earthed, or if there is an earthed screen between
the primary and secondary windings, clearances of
basic insulation on the secondary side not less than
those specified in table 16, but using the next lower
step for rated impulse voltage
N/A
Circuits supplied with a voltage lower than rated
voltage, clearances of functional insulation based on
the working voltage used as the rated voltage in
table 15
P
Creepage distances not less than those appropriate
for the working voltage, taking into account the
material group and the pollution degree
P
29.2
Pollution degree 2 applies, unless
29.2.1
Result
Pollution degree 2.
Verdict
P
precautions taken to protect the insulation;
pollution degree 1
N/A
insulation subjected to conductive pollution;
pollution degree 3
N/A
Compliance is checked by inspection and
measurements as specified
(See appended table)
Insulation located in airflow, pollution degree 3
unless (IEC 60335-2-40)
Protected from airflow in
internal compartments.
P
N/A
insulation enclosed or located so that unlikely to be
exposed to pollution due to normal use
(IEC 60335-2-40)
N/A
Creepage distances of basic insulation not less than
specified in table 17
P
For pollution degree 1, creepage distance not less
than the minimum specified for the clearance in
table 16, if the clearance has been checked
according to the test of clause 14
Pollution degree 2.
N/A
29.2.2
Creepage distances of supplementary insulation at
least as specified for basic insulation in table 17
P
29.2.3
Creepage distances of reinforced insulation at least
double as specified for basic insulation in table 17
P
29.2.4
Creepage distances of functional insulation not less
than specified in table 18
P
Creepage distances may be reduced if the appliance
complies with clause 19 with the functional insulation
short-circuited
N/A
TRF No. IEC60335_2_40F
Page 55 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
29.3
Supplementary and reinforced insulation having
adequate thickness, or a sufficient number of layers,
to withstand the electrical stresses (IEC 60335-1/A1)
P
Compliance checked by:
—
- measurement, in accordance with 29.3.1, or
P
- an electric strength test in accordance with 29.3.2,
or
P
- an assessment of the thermal quality of the material Not applicable.
combined with an electric strength test, in
accordance with 29.3.3
29.3.1
Supplementary insulation having a thickness of at
least 1 mm (IEC 60335-1/A1)
Reinforced insulation having a thickness of at least
2 mm (IEC 60335-1/A1)
29.3.2
29.3.3
Verdict
N/A
P
Non-metallic external
enclosure of indoor unit.
P
Each layer of material withstand the electric strength
test of 16.3 for supplementary insulation
(IEC 60335-1/A1)
P
Supplementary insulation consisting of at least
2 layers (IEC 60335-1/A1)
P
Reinforced insulation consisting of at least 3 layers
P
The insulation is subjected to the dry heat test Bb of
IEC 60068-2-2, followed by (IEC 60335-1/A1)
Not applicable.
N/A
the electric strength of 16.3 (IEC 60335-1/A1)
N/A
If the temperature rise during the tests of clause 19
does not exceed the value specified in table 3, the
test of IEC 60068-2-2 is not carried out
(IEC 60335-1/A1)
N/A
30
RESISTANCE TO HEAT AND FIRE
—
30.1
External parts of non-metallic material,
P
parts supporting live parts, and
P
thermoplastic material providing supplementary or
reinforced insulation,
P
sufficiently resistant to heat
Sufficiently resistant to heat.
Ball-pressure test according to IEC 60695-10-2
P
P
External parts: at 40 °C plus the maximum
temperature rise determined during the test of
clause 11, or at 75 °C, whichever is the higher;
temperature (°C).......................................................:
(See appended table)
P
Parts supporting live parts: at 40 °C plus the
maximum temperature rise determined during the
test of clause 11, or at 125 °C, whichever is the
higher; temperature (°C) ..........................................:
(See appended table)
P
TRF No. IEC60335_2_40F
Page 56 of 97
Report No. 236145
IEC 60335-2-40
Clause
30.2
Requirement – Test
Result
Parts of thermoplastic material providing
supplementary or reinforced insulation, 25 °C plus
the maximum temperature rise determined during
clause 19, if higher; temperature (°C)......................:
(See appended table)
P
Parts of non-metallic material adequately resistant to (See appended table)
ignition and spread of fire
P
Requirement does not apply to decorative trims,
knobs and other parts unlikely to be ignited or to
propagate flames that originate inside the appliance
P
Not applied.
Compliance checked by test of clause 30.2.1. In addition:
- attended appliances, clause 30.2.2
Not applicable.
- unattended appliances, clause 30.2.3 applies
Unattended appliance.
Appliances for remote operation, clause 30.2.3
applies (IEC 60335-1/A2)
30.2.3
30.2.3.1
Glow-wire test of IEC 60695-2-11 at 550 C, unless
—
N/A
P
N/A
Base material of printed circuit board, clause 30.2.4
applies
30.2.1
Verdict
P
Checked with a severity of
550 C.
P
material is classified at least HB40 according to
IEC 60695-11-10 (IEC 60335-1/A2)
N/A
Parts for which the glow-wire test cannot be carried
out meet the requirements in ISO 9772 for category
HBF material (IEC 60335-1/A1)
N/A
Appliances operated while unattended, tested as
specified in 30.2.3.1 and 30.2.3.2
Unattended appliance.
Considered.
P
Test not applicable to conditions as specified
Not applied to such parts.
P
Parts of non-metallic material supporting
connections carrying a current exceeding 0,2 A
during normal operation, and (IEC 60335-1/A2)
P
parts of non-metallic material within a distance of
3 mm, (IEC 60335-1/A2)
P
subjected to glow-wire test of IEC 60695-2-11 with a Glow-wire test of IEC 60695-2test severity of 850 °C (IEC 60335-1/A2)
11 with a test severity of
850C.
No parts exceeding 60 s.
No parts igniting the layer
below.
P
However, glow-wire test not carried out on parts of
material classified as having a glow-wire flammability
index of at least 850 C according to IEC 60695-2-12
(IEC 60335-1/A2)
N/A
Glow-wire flammability index only used if in specified
range of thickness (IEC 60335-1/A2)
N/A
TRF No. IEC60335_2_40F
Page 57 of 97
Report No. 236145
IEC 60335-2-40
Clause
30.2.3.2
Requirement – Test
Result
Glow-wire test not carried out on small parts comply
with needle-flame test of annex E or on small parts
of material classified as V-0 or (IEC 60335-1/A2)
No small parts.
N/A
V-1 according to IEC 60695-1-10 (IEC 60335-1/A2)
N/A
Classified V-0 or V-1 material only used if in
specified range of thickness (IEC 60335-1/A2)
N/A
Test as specified for an interposed shielding material
(IEC 60335-1/A2)
N/A
Parts of non-metallic material supporting
current-carrying connections, and (IEC 60335-1/A2)
P
parts of non-metallic material within a distance of
3 mm, (IEC 60335-1/A2)
P
subjected to glow-wire test of IEC 60695-2-11
Tested as this clause.
However, glow-wire test not carried out on material
Not applicable.
having a glow-wire ignition temperature according to
IEC 60695-2-13 of at least:
Glow-wire test of IEC 60695-2-11, the temperature being:
30.2.4
Verdict
P
N/A
—
- 775 °C, for connections carrying a current
exceeding 0,2 A during normal operation
N/A
- 675 °C, for other connections
N/A
Glow-wire ignition temperature only used if in
specified range of thickness (IEC 60335-1/A2)
N/A
Test as specified for an interposed shielding material
(IEC 60335-1/A2)
N/A
When glow-wire test of IEC 60695-2-11 carried out, temperatures are:
—
- 750 °C, for connections carrying a current
exceeding 0,2 A during normal operation
P
Checked with a severity of
750°C.
- 650 °C, for other connections
N/A
If a flame persists longer than 2 s during test, then
these parts and adjacent parts further subjected to
needle-flame test of annex E, unless
(IEC 60335-1/A1 corr.1)
N/A
material is classified as V-0 or V-1 according to
IEC 60695-11-10 (IEC 60335-1/A2)
N/A
Classified V-0 or V-1 material only used if in
specified range of thickness (IEC 60335-1/A2)
N/A
Base material of printed circuit boards subjected to
needle-flame test of annex E (IEC 60335-1/A2)
Test not carried out by specified items ....................:
TRF No. IEC60335_2_40F
Tested in accordance with
Annex E.
P
N/A
Page 58 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
31
RESISTANCE TO RUSTING
Relevant ferrous parts adequately protected against
rusting
—
Adequately protected.
Before test, coatings are scratched by means of a
harden steel pin as specified (IEC 60335-2-40)
P
Five scratches made at least 5 mm apart and at
least 5 mm from the edges (IEC 60335-2-40)
P
No deterioration.
P
ANNEX A (INFORMATIVE)
ROUTINE TESTS
—
N/A
ANNEX B (NORMATIVE)
APPLIANCES POWERED BY RECHARGEABLE BATTERIES
This annex does not apply to battery chargers
3.6.2
P
Coating not be broken and not loosened from the
metal surface (IEC 60335-2-40)
The following modifications to this standard are
applicable for appliances powered by batteries that
are recharged in the appliance
3.1.9
P
P
Description of routine tests to be carried out by the
manufacturer
B
Verdict
Salt mist test of IEC 60068-2-52, severity 2
(IEC 60335-2-40)
Appliance not deteriorated to such an extent that
compliance with clause 8 and 27 is impaired
(IEC 60335-2-40)
A
Result
Not powered by rechargeable
batteries.
—
N/A
N/A
Appliance operated under the following conditions:
—
- the appliance, supplied by its fully charged battery,
operated as specified in relevant part 2
N/A
- the battery is charged, the battery being initially
discharged to such an extent that the appliance
cannot operate
N/A
- if possible, the appliance is supplied from the
supply mains through its battery charger, the
battery being initially discharged to such an extent
that the appliance cannot operate. The appliance is
operated as specified in relevant part 2
N/A
If the appliance incorporates inductive coupling
between two parts that are detachable from each
other, the appliance is supplied from the supply
mains with the detachable part removed
N/A
Part to be removed in order to discard the battery is
not considered to be detachable
N/A
TRF No. IEC60335_2_40F
Page 59 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
5.101
Appliances supplied from the supply mains tested as
specified for motor-operated appliances
N/A
7.1
Battery compartment for batteries intended to be
replaced by the user, marked with battery voltage
and polarity of the terminals
N/A
7.12
The instructions for appliances incorporating
batteries intended to be replaced by the user
includes required information
N/A
Details about how to remove batteries containing
materials hazardous to the environment given
N/A
7.15
Markings placed on the part of the appliance
connected to the supply mains
N/A
8.2
Appliances having batteries that according to the
instruction may be replaced by the user need only
have basic insulation between live parts and the
inner surface of the battery compartment
N/A
If the appliance can be operated without batteries,
double or reinforced insulation required
N/A
11.7
The battery is charged for the period described
N/A
19.1
Appliances subjected to tests of clause 19.101,
19.102 and 19.103
N/A
19.101
Appliances supplied at rated voltage for 168 h, the
battery being continually charged
N/A
19.102
Short-circuiting of the terminals of the battery, being
fully charged, for appliances having batteries that
can be removed without the aid of a tool
N/A
19.103
Appliances having batteries replaceable by the user
supplied at rated voltage under normal operation
with the battery removed or in any position allowed
by the construction
N/A
21.101
Appliances having pins for insertion into
socket-outlets have adequate mechanical strength,
checked according to procedure 2 of
IEC 60068-2-32
N/A
Part of the appliance incorporating the pins subjected to the free fall test, procedure 2,
of IEC 60068-2-32, the number of falls being:
Verdict
—
- 100, the mass of part does not exceed 250 g
N/A
- 50, the mass of part exceeds 250 g
N/A
After the test, the requirements of 8.1, 15.1.1, 16.3
and clause 29 are met
N/A
22.3
Appliances having pins for insertion into
socket-outlets tested as fully assembled as possible
N/A
25.13
An additional lining or bushing not required for
interconnection cords operating at safety extra-low
voltage
N/A
TRF No. IEC60335_2_40F
Page 60 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
30.2
For parts of the appliance connected to the supply
mains during the charging period, 30.2.3 applies
N/A
For other parts, 30.2.2 applies
N/A
ANNEX C (NORMATIVE)
AGEING TEST ON MOTORS
—
C
Tests, as described, carried out when doubt with
regard to the temperature classification of the
insulation of a motor winding
E
5
Result
No doubt.
Verdict
N/A
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST
—
Needle-flame test carried out in accordance with IEC 60695-11-5, with the following
modifications (IEC 60335-1/A2):
—
Severities (IEC 60335-1/A2)
—
Duration of application of test flame is 30 s ± 1 s
(IEC 60335-1/A2)
PCB
P
9
Test procedure (IEC 60335-1/A2)
9.1
Specimen so arranged that flame can be applied to a
vertical or horizontal edge as shown in examples of
figure 1 (IEC 60335-1/A2)
N/A
9.2
First paragraph does not apply (IEC 60335-1/A2)
N/A
If possible, flame is applied at least 10 mm from a
corner (IEC 60335-1/A2)
N/A
Test carried out on one specimen (IEC 60335-1/A2)
N/A
If specimen does not withstand test, test may be
repeated on two additional specimens, both
withstanding test (IEC 60335-1/A2)
N/A
9.3
11
—
Evaluation of test results (IEC 60335-1/A2)
—
The duration of burning not exceeding 30 s
(IEC 60335-1/A2)
N/A
However, for printed circuit boards, the duration of
burning not exceeding 15 s (IEC 60335-1/A2)
P
ANNEX F (NORMATIVE)
CAPACITORS
—
Capacitors likely to be permanently subjected to the supply voltage, and used for
radio interference suppression or voltage dividing, comply with the following clauses
of IEC 60384-14, with the following modifications:
—
1.5
Terminology
—
1.5.3
Class X capacitors tested according to subclass X2
F
TRF No. IEC60335_2_40F
Complying with IEC 60384-14.
N/A
Page 61 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
1.5.4
This subclause is applicable
1.6
Marking
Result
Items a) and b) are applicable
3.4
Approval testing
3.4.3.2
Table II is applicable as described
4.1
Visual examination and check of dimensions
This subclause is applicable
Verdict
N/A
—
N/A
—
N/A
—
N/A
4.2
Electrical tests
4.2.1
This subclause is applicable
N/A
4.2.5
This subclause is applicable
N/A
4.2.5.2
Only table IX is applicable
N/A
Values for test A apply
N/A
However, for capacitors in heating appliances the
values for test B or C apply
N/A
4.12
4.13
Damp heat, steady state
4.14.7
4.17
N/A
Only insulation resistance and voltage proof are
checked
N/A
Impulse voltage
Endurance
N/A
—
N/A
Only insulation resistance and voltage proof are
checked
N/A
Visual examination, no visible damage
N/A
Passive flammability test
Active flammability test
This subclause is applicable
G
—
Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7
applicable
This subclause is applicable
4.18
—
This subclause is applicable
This subclause is applicable
4.14
—
—
N/A
—
N/A
ANNEX G (NORMATIVE)
SAFETY ISOLATING TRANSFORMERS
—
The following modifications to this standard are applicable for safety isolating
transformers:
—
TRF No. IEC60335_2_40F
Page 62 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
7
Marking and instructions
—
7.1
Transformers for specific use marked with:
—
17
Result
- name, trademark or identification mark of the
manufacturer or responsible vendor
N/A
- model or type reference
N/A
Overload protection of transformers and associated circuits
Fail-safe transformers comply with subclause 15.5 of
IEC 61558-1
22
Verdict
Construction
Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are
applicable
—
N/A
—
N/A
29
Clearances, creepage distances and solid insulation
29.1, 29.2
and 29.3
The distances specified in items 2a, 2c and 3 in
table 13 of IEC 61558-1 apply
H
ANNEX H (NORMATIVE)
SWITCHES
—
Switches comply with the following clauses of IEC 61058-1, as modified:
—
8
13
—
N/A
- The tests of IEC 61058-1 carried out under the
conditions occurring in the appliance
N/A
- Before being tested, switches are operated
20 times without load
N/A
Marking and documentation
—
Switches are not required to be marked
N/A
However, switches that can be tested separately
from the appliance marked with the manufacturer’s
name or trade mark and the type reference
N/A
Mechanism
The tests may be carried out on a separate sample
—
N/A
15
Insulation resistance and dielectric strength
—
15.1
Not applicable
N/A
15.2
Not applicable
N/A
15.3
Applicable for full disconnection and
micro-disconnection
N/A
17
Endurance
—
Compliance is checked on three separate appliances
or switches
N/A
For 17.2.4.4, the number of cycles is 10 000, unless
otherwise specified in 24.1.3 of the relevant part 2 of
IEC 60335
N/A
TRF No. IEC60335_2_40F
Page 63 of 97
Report No. 236145
IEC 60335-2-40
Clause
20
Requirement – Test
Result
Switches for operation under no load and which can
be operated only by a tool and switches operated by
hand that are interlocked so that they cannot be
operated under load, are not subjected to the tests
N/A
Subclause 17.2.2 and 17.2.5.2 are not applicable
N/A
The ambient temperature during the test is that
occurring in the appliance during the test of
clause 11 in IEC 60335-1
N/A
Temperature rise of the terminals not more than
30 K above the temperature rise measured in
clause 11 of IEC 60335-1
N/A
Clearances, creepage distances, solid insulation and coatings of rigid printed board
assemblies
This clause is applicable to clearances and creepage
distances for functional insulation, across full
disconnection and micro-disconnection, as stated in
table 24
J
5.7
N/A
—
Testing of protective coatings of printed circuit boards carried out in accordance with
IEC 60664-3 with following modifications (IEC 60335-1/A2):
—
Conditioning of the test specimens (IEC 60335-1/A2)
—
No coated PCBs.
Cold (IEC 60335-1/A2)
N/A
Rapid change of temperature (IEC 60335-1/A2)
—
Severity 1 is specified (IEC 60335-1/A2)
5.9
N/A
Additional tests (IEC 60335-1/A2)
—
Subclause not applicable (IEC 60335-1/A2)
K
N/A
—
Test carried out at -25 C (IEC 60335-1/A2)
5.7.3
—
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS
When production samples used, three samples of
printed circuit board are tested (IEC 60335-1/A2)
5.7.1
Verdict
N/A
—
ANNEX K (NORMATIVE)
OVERVOLTAGE CATEGORIES
The information on overvoltage categories is
extracted from IEC 60664-1
Considered.
P
Overvoltage category is a numeral defining a
transient overvoltage condition
Considered.
P
Equipment of overvoltage category IV is for use at
the origin of the installation
TRF No. IEC60335_2_40F
N/A
Page 64 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Equipment of overvoltage category III is equipment
in fixed installations and for cases where the
reliability and the availability of the equipment is
subject to special requirements
Equipment of overvoltage category II is energy
consuming equipment to be supplied from the fixed
installation
L
M
Verdict
N/A
Overvoltage category II.
P
If such equipment is subjected to special
requirements with regard to reliability and availability,
overvoltage category III applies
N/A
Equipment of overvoltage category I is equipment for
connection to circuits in which measures are taken to
limit transient overvoltages to an appropriate low
level
N/A
ANNEX L (INFORMATIVE)
GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES
—
Sequences for the determination of clearances and
creepage distances
P
Considered.
—
ANNEX M (NORMATIVE)
POLLUTION DEGREE
The information on pollution degrees is extracted
from IEC 60664-1
Considered.
P
Pollution
—
The microenvironment determines the effect of
pollution on the insulation, taking into account the
microenvironment
P
Means may be provided to reduce pollution at the
insulation by effective enclosures or similar
P
Minimum clearances specified where pollution may
be present in the microenvironment
P
Degrees of pollution in the microenvironment
—
For evaluating creepage distances, the following degrees of pollution in the
microenvironment are established:
—
- pollution degree 1: no pollution or only dry,
non-conductive pollution occurs. The pollution has
no influence
- pollution degree 2: only non-conductive pollution
occurs, except that occasionally a temporary
conductivity caused by condensation is to be
expected
TRF No. IEC60335_2_40F
N/A
Pollution degree 2.
P
Page 65 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
- pollution degree 3: conductive pollution occurs or
dry non-conductive pollution occurs that becomes
conductive due to condensation that is to be
expected
N/A
- pollution degree 4: the pollution generates
persistent conductivity caused by conductive dust
or by rain or snow
N/A
ANNEX N (NORMATIVE)
PROOF TRACKING TEST
—
The proof tracking test is carried out in accordance with IEC 60112 with the following
modifications:
—
7
Test apparatus
—
7.3
Test solutions
—
N
Test solution A is used
Solution A:
0,1% NH4Cl in de-ionized
water.
P
10
Determination of proof tracking index (PTI)
—
10.1
Procedure
—
Proof voltage is 100 V, 175 V, 400 V or 600 V .......:
175V
Last paragraph of clause 3 applies
P
The test is carried out on five specimens
P
In case of doubt, additional test with proof voltage
reduced by 25 V, the number of drops increased to
100
10.2
Report
The report stating if the PTI value was based on a
test using 100 drops with a test voltage of (PTI-25) V
O
P
P
N/A
—
N/A
ANNEX O (INFORMATIVE)
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30
—
Description of tests for determination of resistance to Considered.
heat and fire (IEC 60335-1/A2)
P
ANNEX P (INFORMATIVE)
GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES
—
Modifications applicable for class 0 and 0I appliances having a rated voltage
exceeding 150 V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE
—
TRF No. IEC60335_2_40F
Page 66 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
Modifications may also be applied to class I appliances having a rated voltage
exceeding 150 V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE, if liable to be connected to a supply mains that
excludes the protective earthing conductor
—
5
General conditions for the tests
—
5.7
The ambient temperature for the tests of clauses 11
and 13 is 40 +3 0 °C
7
Marking and instructions
7.1
The appliance marked with the letters WDaE
N/A
7.12
The instructions state that the appliance is to be
supplied through a RCD having a rated residual
operating current not exceeding 30 mA
N/A
The instructions state that the appliance is
considered to be suitable for use in countries having
a warm damp equable climate, but may also be used
in other countries
N/A
Not applicable.
N/A
—
11
Heating
11.8
The values of table 3 reduced by 15 K
13
Leakage current and electric strength at operating temperature
13.2
The leakage current for class I appliances not
exceeding 0,5 mA
15
Moisture resistance
15.3
The value of t is 37 °C
16
Leakage current and electric strength
16.2
The leakage current for class I appliances not
exceeding 0,5 mA
19
Abnormal operation
19.13
The leakage current test of clause 16.2 is applied in
addition to the electric strength test of 16.3
Q
ANNEX Q (INFORMATIVE)
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS
—
Description of tests for appliances incorporating electronic circuits (IEC 60335-1/A2)
P
ANNEX R (NORMATIVE)
SOFTWARE EVALUATION
—
Software evaluated in accordance with the following clauses of annex H of
IEC 60730-1, as modified:
—
R
H.2
Definitions
Only definitions H.2.16 to H.2.20 applicable
TRF No. IEC60335_2_40F
—
N/A
—
N/A
—
N/A
—
N/A
—
N/A
Not considered.
N/A
N/A
Page 67 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
H.7
Information
N/A
Only footnotes 12) to 18) of Table 7.2, as modified,
applicable
N/A
Controls using software
N/A
All the subclauses of H.11.12, as modified, except
H.11.12.6 and H.11.12.6.1, applicable
N/A
Delete text
N/A
H.11.12
H.11.12.7
Result
Verdict
H.11.12.7.1 For appliances using software class C having a
single channel with self-test and monitoring
structure, the manufacturer provides the measures
necessary to address the fault/errors in safety
related segments and data
N/A
H.11.12.8
Software fault/error detection occurs before
compliance with clause 19.13 of IEC 60335-1 is
impaired
N/A
H.12.8.1
Replace text
N/A
H.12.13
Software and safety related hardware under its
control initializes and terminates before compliance
with clause 19.13 of IEC 60335-1 is impaired
N/A
AA
ANNEX AA (INFORMATIVE) (IEC 60335-2-40)
EXAMPLES FOR OPERATING TEMPERATURES OF THE APPLIANCE
—
BB
ANNEX BB (NORMATIVE) (IEC 60335-2-40)
SELECTED INFORMATION ABOUT REFRIGERANTS
—
CC
ANNEX CC (INFORMATIVE) (IEC 60335-2-40/A1)
TRANSPORTATION, MARKING AND STORAGE FOR UNITS THAT EMPLOY
FLAMMABLE REFRIGERANTS
—
CC.1
Transport of equipment containing flammable
refrigerants (IEC 60335-2-40/A1)
CC.2
Marking of equipment using signs
(IEC 60335-2-40/A1)
N/A
CC.3
Disposal of equipment using flammable refrigerants
(IEC 60335-2-40/A1)
N/A
CC.4
Storage of equipment/appliances
(IEC 60335-2-40/A1)
N/A
CC.5
Storage of packed (unsold) equipment
(IEC 60335-2-40/A1)
N/A
TRF No. IEC60335_2_40F
Non-flammable refrigerant.
N/A
Page 68 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
DD
ANNEX DD (NORMATIVE) (IEC 60335-2-40/A1)
SERVICE OPERATIONS
DD.1
Generals (IEC 60335-2-40/A1)
DD.2
Symbols (IEC 60335-2-40/A1)
N/A
DD.3
Information in manual (IEC 60335-2-40/A1 corr.1)
N/A
DD.4
Information on servicing (IEC 60335-2-40/A1)
N/A
DD.5
Repairs to sealed components (IEC 60335-2-40/A1)
N/A
DD.6
Repair to intrinsically safe components
(IEC 60335-2-40/A1)
N/A
DD.7
Cabling (IEC 60335-2-40/A1)
N/A
DD.8
Detection of flammable refrigerants
(IEC 60335-2-40/A1)
N/A
DD.9
Leak detection methods (IEC 60335-2-40/A1)
N/A
DD.10
Removal and evacuation (IEC 60335-2-40/A1)
N/A
DD.11
Charging procedures (IEC 60335-2-40/A1)
N/A
DD.12
Decommissioning (IEC 60335-2-40/A1)
N/A
DD.13
Labelling (IEC 60335-2-40/A1)
N/A
DD.14
Recovery (IEC 60335-2-40/A1)
N/A
EE
ANNEX EE (NORMATIVE) (IEC 60335-2-40/A1)
PRESSURE TESTS
EE.1
General (IEC 60335-2-40/A1)
—
Intended for the use of a nonflammable refrigerant.
N/A
—
Test location:
Considered heat exchangers of
indoor unit.
P
Test result:
No leakage. No hazard.
EE.2
Pressure test value determined under testing carried
out in clause 11 (IEC 60335-2-40/A1)
N/A
EE.3
Pressure test value determined under testing carried
out in clause 19 (IEC 60335-2-40/A1)
N/A
EE.4
Pressure test value determined under testing carried
out under standstill conditions (IEC 60335-2-40/A1)
N/A
EE.5
Fatigue test option for Clauses EE.1 and EE.4.1
(IEC 60335-2-40/A1)
TRF No. IEC60335_2_40F
Rated compressive strength:
15,2 MPa
Measured compressive
strength: 16,5 MPa
250 000 cycles.
P
Page 69 of 97
Report No. 236145
IEC 60335-2-40
Clause
Requirement – Test
Result
Verdict
FF
ANNEX FF (NORMATIVE) (IEC 60335-2-40/A1)
LEAK SIMULATION TESTS
FF.1
General (IEC 60335-2-40/A1)
FF.2
Test methods (IEC 60335-2-40/A1 corr.1)
GG
ANNEX GG (NORMATIVE) (IEC 60335-2-40/A1)
CHARGE LIMITS, VENTILATION REQUIREMENTS AND REQUIREMENTS FOR
SECONDARY CIRCUITS
GG.1
Requirements for charge limits in ventilated areas
(IEC 60335-2-40/A1 Corr.1)
GG.2
Requirements for charge limits in unventilated areas
(IEC 60335-2-40/A1 Corr.1)
N/A
GG.3
Requirements for charge limits in areas with
mechanical ventilation (IEC 60335-2-40/A1)
N/A
GG.4
Requirements for mechanical ventilation within the
appliance enclosure (IEC 60335-2-40/A1)
N/A
GG.5
Requirements for mechanical ventilation for rooms
complying with ISO 5149 (IEC 60335-2-40/A1)
N/A
GG.6
Requirements for refrigeration systems employing
secondary heat exchangers
(IEC 60335-2-40/A1 Corr.1)
N/A
GG.7
The appliance shall then be tested with a maximum
water flow under the conditions described in g)
(IEC 60335-2-40/A1)
N/A
—
Intended for the use of a nonflammable refrigerant.
N/A
N/A
Intended for the use of a nonflammable refrigerant.
—
N/A
ANNEX EMF (EN 62233)
The Tested product also complies to the requirements of EN 62233:2008
—
Measuring distance (cm)..........................................:
30 cm, Around.
P
Background noise level (%) .....................................:
Less than 0.5 %
P
Limit ……………100%
Measured max. : 2.1 %
P
TRF No. IEC60335_2_40F
Page 70 of 97
10.1
TABLE: Power input deviation 1)
P
P rated
(W)
P measured
(W)
P
(%)
Required P
(%)
Remark
220V~ 50Hz
385
360.0
-6.5
+20
Pass
230V~ 50Hz
385
370.0
-3.9
+20
Pass
240V~ 50Hz
385
390.0
+1.3
+20
Pass
Input deviation of/at:
10.2
Report No. 236145
TABLE: Current deviation 1)
P
I rated
(A)
I measured
(A)
I
(%)
Required I
(%)
Remark
220V~ 50Hz
3.0
3.00
0.0
+20
Pass
230V~ 50Hz
3.0
2.90
-3.3
+20
Pass
240V~ 50Hz
3.0
2.98
-0.8
+20
Pass
Current deviation of/at
supplementary information:
This is for the model of indoor unit, AM140FNHDEH.
1)
Measured maximum value under the test condition as below:
a) for lowest cooling,
- Room temperature, indoor DB/WB (C): 27 / 19
- Room temperature, outdoor DB/WB (C): 35 / 24
b) for lowest cooling,
- Room temperature, indoor DB/WB (C): 29 / 19
- Room temperature, outdoor DB/WB (C): 46 / 24
c) for highest heating,
- Room temperature, indoor DB/WB (C): 20 / 15
- Room temperature, outdoor DB/WB (C): 7 / 6
TRF No. IEC60335_2_40F
Page 71 of 97
10.1
TABLE: Power input deviation 1)
P
P rated
(W)
P measured
(W)
P
(%)
Required P
(%)
Remark
220V~ 50Hz
333
308.0
-7.5
+20
Pass
230V~ 50Hz
333
318.0
-4.5
+20
Pass
240V~ 50Hz
333
338.0
+1.5
+20
Pass
Input deviation of/at:
10.2
Report No. 236145
TABLE: Current deviation 1)
P
I rated
(A)
I measured
(A)
I
(%)
Required I
(%)
Remark
220V~ 50Hz
2.58
2.56
-0.6
+20
Pass
230V~ 50Hz
2.58
2.50
-3.1
+20
Pass
240V~ 50Hz
2.58
2.58
0.0
+20
Pass
Current deviation of/at
supplementary information:
This is for the model of indoor unit, AM128FNHDEH.
1)
Measured maximum value under the test condition as below:
a) for lowest cooling,
- Room temperature, indoor DB/WB (C): 27 / 19
- Room temperature, outdoor DB/WB (C): 35 / 24
b) for lowest cooling,
- Room temperature, indoor DB/WB (C): 29 / 19
- Room temperature, outdoor DB/WB (C): 46 / 24
c) for highest heating,
- Room temperature, indoor DB/WB (C): 20 / 15
- Room temperature, outdoor DB/WB (C): 7 / 6
TRF No. IEC60335_2_40F
Page 72 of 97
10.1
TABLE: Power input deviation 1)
P
P rated
(W)
P measured
(W)
P
(%)
Required P
(%)
Remark
220V~ 50Hz
305
278.0
-8.9
+20
Pass
230V~ 50Hz
305
288.0
-5.6
+20
Pass
240V~ 50Hz
305
308.0
+1.0
+20
Pass
Input deviation of/at:
10.2
Report No. 236145
TABLE: Current deviation 1)
P
I rated
(A)
I measured
(A)
I
(%)
Required I
(%)
Remark
220V~ 50Hz
2.35
2.31
-1.5
+20
Pass
230V~ 50Hz
2.35
2.29
-2.6
+20
Pass
240V~ 50Hz
2.35
2.35
0.0
+20
Pass
Current deviation of/at
supplementary information:
This is for the model of indoor unit, AM112FNHDEH.
1)
Measured maximum value under the test condition as below:
a) for lowest cooling,
- Room temperature, indoor DB/WB (C): 27 / 19
- Room temperature, outdoor DB/WB (C): 35 / 24
b) for lowest cooling,
- Room temperature, indoor DB/WB (C): 29 / 19
- Room temperature, outdoor DB/WB (C): 46 / 24
c) for highest heating,
- Room temperature, indoor DB/WB (C): 20 / 15
- Room temperature, outdoor DB/WB (C): 7 / 6
TRF No. IEC60335_2_40F
Page 73 of 97
11.8
Report No. 236145
TABLE: Heating test, thermocouples
P
Test voltage (V) ....................................................... : 254,4V (=1,06 x 240V) 50Hz

Ambient, t1 (°C) .........................................................: Indoor (DB / WB): 27 / 19
Outdoor (DB / WB): 35 / 24

Ambient, t2 (°C) .........................................................: Indoor (DB / WB): 27 / 19
Outdoor (DB / WB): 35 / 24

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
37.8
150
Enclosure of indoor fan motor2
37.2
150
Interconnection cord separation
27.5
75
Terminal block
30.4
85
Choke coil (BLDC module)
41.3
T120
X-capacitor (X701) (BLDC module)
39.6
T100
Reactor
41.6
165 (Cl.H)
Fuse holder (BLDC module)
31.2
See cl.30.1
Y-capacitor (BLDC module)
40.3
-
Electrolytic capacitor (BLDC module)
30.0
T85
Connector (CN71) (BLDC module)
29.9
See cl.30.1
PCB surface (BLDC module)
43.3
145
Switching transformer winding
31.4
T130
Electrolytic capacitor
37.6
T85
Choke coil (L101)
31.5
T120
X-capacitor (CX101)
26.8
T100
Fuse holder
29.8
See cl.30.1
Relay (RY701)
35.4
T70
PCB surface
33.4
145
External enclosure
27.9
85
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition: Lowest cooling under the climatic class T1.
TRF No. IEC60335_2_40F
Page 74 of 97
11.8
Report No. 236145
TABLE: Heating test, thermocouples
P
Test voltage (V) ....................................................... : 254,4V (=1,06 x 240V) 50Hz

Ambient, t1 (°C) .........................................................: Indoor (DB / WB): 29 / 19
Outdoor (DB / WB): 46 / 24

Ambient, t2 (°C) .........................................................: Indoor (DB / WB): 29 / 19
Outdoor (DB / WB): 46 / 24

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
39.3
150
Enclosure of indoor fan motor2
38.8
150
Interconnection cord separation
29.5
75
Terminal block
32.1
85
Choke coil (BLDC module)
42.5
T120
X-capacitor (X701) (BLDC module)
41.0
T100
Reactor
42.9
165 (Cl.H)
Fuse holder (BLDC module)
32.9
See cl.30.1
Y-capacitor (BLDC module)
41.7
-
Electrolytic capacitor (BLDC module)
32.1
T85
Connector (CN71) (BLDC module)
31.8
See cl.30.1
PCB surface (BLDC module)
44.7
145
Switching transformer winding
33.6
T130
Electrolytic capacitor
39.2
T85
Choke coil (L101)
33.4
T120
X-capacitor (CX101)
28.9
T100
Fuse holder
31.7
See cl.30.1
Relay (RY701)
37.2
T70
PCB surface
35.5
145
External enclosure
30.0
85
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition: Lowest cooling under the climatic class T3.
TRF No. IEC60335_2_40F
Page 75 of 97
11.8
Report No. 236145
TABLE: Heating test, thermocouples
P
Test voltage (V) ....................................................... : 254,4V (=1,06 x 240V) 50Hz

Ambient, t1 (°C) .........................................................: Indoor (DB / WB): 20 / 15
Outdoor (DB / WB): 7 / 6

Ambient, t2 (°C) .........................................................: Indoor (DB / WB): 20 / 15
Outdoor (DB / WB): 7 / 6

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
28.8
150
Enclosure of indoor fan motor2
27.5
150
Interconnection cord separation
20.3
75
Terminal block
23.3
85
Choke coil (BLDC module)
34.3
T120
X-capacitor (X701) (BLDC module)
32.4
T100
Reactor
34.8
165 (Cl.H)
Fuse holder (BLDC module)
23.9
See cl.30.1
Y-capacitor (BLDC module)
33.6
-
Electrolytic capacitor (BLDC module)
22.8
T85
Connector (CN71) (BLDC module)
22.6
See cl.30.1
PCB surface (BLDC module)
36.5
145
Switching transformer winding
24.0
T130
Electrolytic capacitor
31.0
T85
Choke coil (L101)
24.4
T120
X-capacitor (CX101)
19.8
T100
Fuse holder
22.5
See cl.30.1
Relay (RY701)
28.5
T70
PCB surface
26.3
145
External enclosure
20.6
85
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition: Highest heating.
TRF No. IEC60335_2_40F
Page 76 of 97
13.2
Report No. 236145
P
TABLE: Leakage current
Heating appliances: 1,15 x rated power input ...... :
-

Motor-operated and combined appliances:
1,06 x rated voltage ............................................... :
254,4V (=1,06 x 240V)

Leakage current between
I (mA)
Max. allowed I (mA)
--
--
Live line to heat exchanger (Stand-by)
0.62
10.0 1)
Neutral line to heat exchanger (Stand-by)
0.61
10.0 1)
--
--
Live line to heat exchanger (Operating)
0.62
10.0 1)
Neutral line to heat exchanger (Operating)
0.61
10.0 1)
Live line to metal foil of non-metallic part (Operating)
0.01
0.25
Neutral line to metal foil of non-metallic part (Operating)
0.01
0.25
--
--
Live line to heat exchanger (Operating)
0.61
10.0 1)
Neutral line to heat exchanger (Operating)
0.61
10.0 1)
Live line to metal foil of non-metallic part (Operating)
0.01
0.25
Neutral line to metal foil of non-metallic part (Operating)
0.01
0.25
Stand-by mode
Cooling mode
Heating mode
supplementary information:
1)
The maximum allowed limit can be less than 10mA considering the rated maximum power input based on
the combination of indoor unit and outdoor unit.
- for AM100FXVAGH (outdoor unit); 6.80 kW (cooling, T1) /6.70 kW (heating)
Required limit: 2mA/kW per each operating mode, but with a maximum value of 10 mA.
This appliance is not intended to be installed where accessible to the general public, but in this test report the
leakage current is limited to the requirement of an appliance which may be accessible to the general public.
13.3
P
TABLE: Electric strength
Test voltage applied between:
Voltage (V)
Breakdown
(Yes/No)
Line to heat exchanger of indoor unit (Basic insulation)
1000
No
Line to metallic enclosure of indoor unit (Basic insulation)
1000
No
Line to non-metallic part of indoor unit (Reinforced insulation)
3000
No
supplementary information:
14
N/A
TABLE: Transient overvoltages
Clearance between:
--
Cl (mm)
Required
Cl (mm)
Rated impulse
voltage (V)
Impulse test
voltage (V)
Flashover
(Yes/No)
--
--
--
--
--
supplementary information: Not applicable.
TRF No. IEC60335_2_40F
Page 77 of 97
16.2
Report No. 236145
P
TABLE: Leakage current
Single phase appliances: 1,06 x rated voltage ..... :
254,4V (=1,06 x 240V)

Three phase appliances 1,06 x rated voltage
divided by 3: ......................................................... :
-

Leakage current between
I (mA)
Max. allowed I (mA)
Lines to heat exchanger
0.90
10.0 1)
Lines to metal foil of non-metallic part
0.01
0.25
supplementary information:
1)
The maximum allowed limit can be less than 10mA considering the rated maximum power input based on
the combination of indoor unit and outdoor unit.
- for AM100FXVAGH (outdoor unit); 6.80 kW (cooling, T1) / 6.70 kW (heating)
Required limit: 2mA/kW per each operating mode, but with a maximum value of 10 mA.
This appliance is not intended to be installed where accessible to the general public, but in this test report the
leakage current is limited to the requirement of an appliance which may be accessible to the general public.
16.3
P
TABLE: Electric strength
Test voltage applied between:
Voltage (V)
Breakdown
(Yes/No)
Line to heat exchanger of indoor unit (Basic insulation)
1250
No
Line to metallic enclosure of indoor unit (Basic insulation)
1250
No
Line to non-metallic part of indoor unit (Reinforced insulation)
3000
No
supplementary information:
17
N/A
TABLE: Overload protection, temperature rise
T (K)
Max. T (K)
--
--
--
--
--
--
Temperature rise of part/at:
supplementary information:
TRF No. IEC60335_2_40F
Page 78 of 97
19.5
Report No. 236145
P
TABLE: Abnormal operation
Test voltage (V)........................................................ :

240V 50Hz
Ambient, t1 (°C) ........................................................ : Indoor (DB / WB): 23 / (15)
Outdoor (DB / WB): 23 / (15)

Ambient, t2 (°C) ........................................................ : Indoor (DB / WB): 23 / (15)
Outdoor (DB / WB): 23 / (15)

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
32.4
150
Enclosure of indoor fan motor2
32.7
150
Interconnection cord separation
22.9
-
Terminal block
27.1
Choke coil (BLDC module)
36.0
-
X-capacitor (X701) (BLDC module)
32.9
-
Reactor
39.7
-
Fuse holder (BLDC module)
27.9
-
Y-capacitor (BLDC module)
35.0
-
Electrolytic capacitor (BLDC module)
24.1
-
Connector (CN71) (BLDC module)
24.4
-
PCB surface (BLDC module)
38.3
-
Switching transformer winding
25.4
-
Electrolytic capacitor
30.3
-
Choke coil (L101)
26.4
-
X-capacitor (CX101)
22.4
-
Fuse holder
24.7
-
Relay (RY701)
30.0
-
PCB surface
27.9
-
External enclosure
23.1
175
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition: Lowest cooling with the air-inlet to heat exchanger of indoor unit being blocked.
TRF No. IEC60335_2_40F
Page 79 of 97
19.5
Report No. 236145
P
TABLE: Abnormal operation
Test voltage (V)........................................................ :

240V 50Hz
Ambient, t1 (°C) ........................................................ : Indoor (DB / WB): 23 / (15)
Outdoor (DB / WB): 23 / (15)

Ambient, t2 (°C) ........................................................ : Indoor (DB / WB): 23 / (15)
Outdoor (DB / WB): 23 / (15)

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
76.9
150
Enclosure of indoor fan motor2
80.5
150
Interconnection cord separation
29.2
-
Terminal block
32.2
Choke coil (BLDC module)
40.8
-
X-capacitor (X701) (BLDC module)
39.5
-
Reactor
42.7
-
Fuse holder (BLDC module)
31.9
-
Y-capacitor (BLDC module)
41.4
-
Electrolytic capacitor (BLDC module)
32.4
-
Connector (CN71) (BLDC module)
32.0
-
PCB surface (BLDC module)
43.0
-
Switching transformer winding
34.6
-
Electrolytic capacitor
40.8
-
Choke coil (L101)
33.8
-
X-capacitor (CX101)
28.7
-
Fuse holder
31.9
-
Relay (RY701)
38.2
-
PCB surface
36.5
-
External enclosure
30.3
175
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition: Lowest cooling with the air-inlet to heat exchanger of outdoor unit being blocked.
TRF No. IEC60335_2_40F
Page 80 of 97
19.7
Report No. 236145
P
TABLE: Abnormal operation
Test voltage (V) ....................................................... :

240V 50Hz
Ambient, t1 (°C) .........................................................: Indoor (DB / WB): 39 / (29)
Outdoor (DB / WB): 56 / (34)

Ambient, t2 (°C) .........................................................: Indoor (DB / WB): 39 / (29)
Outdoor (DB / WB): 56 / (34)

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
58.6
150
Enclosure of indoor fan motor2
58.5
150
Interconnection cord separation
39.3
-
Terminal block
42.1
Choke coil (BLDC module)
52.6
-
X-capacitor (X701) (BLDC module)
50.6
-
Reactor
52.1
-
Fuse holder (BLDC module)
42.8
-
Y-capacitor (BLDC module)
51.9
-
Electrolytic capacitor (BLDC module)
41.8
-
Connector (CN71) (BLDC module)
41.5
-
PCB surface (BLDC module)
53.8
-
Switching transformer winding
43.1
-
Electrolytic capacitor
48.4
-
Choke coil (L101)
43.1
-
X-capacitor (CX101)
38.7
-
Fuse holder
41.5
-
Relay (RY701)
46.0
-
PCB surface
44.2
-
External enclosure
39.7
175
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit,
2) Test condition: Lowest cooling with +10K
TRF No. IEC60335_2_40F
Page 81 of 97
19.10
Report No. 236145
P
TABLE: Abnormal operation
Test voltage (V) ....................................................... :

240V 50Hz
Ambient, t1 (°C) .........................................................: Indoor (DB / WB): 29 / 19
Outdoor (DB / WB): 46 / 24

Ambient, t2 (°C) .........................................................: Indoor (DB / WB): 29 / 19
Outdoor (DB / WB): 46 / 24

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
64.7
150
Enclosure of indoor fan motor2
40.6
150
Interconnection cord separation
29.1
-
Terminal block
31.5
Choke coil (BLDC module)
37.0
-
X-capacitor (X701) (BLDC module)
36.1
-
Reactor
40.1
-
Fuse holder (BLDC module)
33.9
-
Y-capacitor (BLDC module)
42.4
-
Electrolytic capacitor (BLDC module)
32.7
-
Connector (CN71) (BLDC module)
31.3
-
PCB surface (BLDC module)
40.5
-
Switching transformer winding
34.8
-
Electrolytic capacitor
41.3
-
Choke coil (L101)
33.5
-
X-capacitor (CX101)
28.7
-
Fuse holder
31.4
-
Relay (RY701)
36.9
-
PCB surface
35.4
-
External enclosure
30.2
175
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition:
Lowest cooling with the motor rotor of indoor unit being locked.
TRF No. IEC60335_2_40F
Page 82 of 97
19.10
Report No. 236145
P
TABLE: Abnormal operation
Test voltage (V) ....................................................... :

240V 50Hz
Ambient, t1 (°C) .........................................................: Indoor (DB / WB): 29 / 19
Outdoor (DB / WB): 46 / 24

Ambient, t2 (°C) .........................................................: Indoor (DB / WB): 29 / 19
Outdoor (DB / WB): 46 / 24

Thermocouple locations
T (°C)
Max. T (°C)
Enclosure of indoor fan motor1
52.9
150
Enclosure of indoor fan motor2
50.6
150
Interconnection cord separation
29.1
-
Terminal block
32.5
Choke coil (BLDC module)
46.6
-
X-capacitor (X701) (BLDC module)
41.8
-
Reactor
46.3
-
Fuse holder (BLDC module)
31.3
-
Y-capacitor (BLDC module)
39.7
-
Electrolytic capacitor (BLDC module)
31.5
-
Connector (CN71) (BLDC module)
31.1
-
PCB surface (BLDC module)
44.9
-
Switching transformer winding
32.7
-
Electrolytic capacitor
38.6
-
Choke coil (L101)
33.2
-
X-capacitor (CX101)
28.6
-
Fuse holder
31.3
-
Relay (RY701)
37.3
-
PCB surface
35.4
-
External enclosure
29.6
175
supplementary information:
1) This is for the representative model of indoor unit, AM140FNHDEH in connection with the outdoor unit.
2) Test condition:
Lowest cooling with the motor rotor of outdoor unit being locked.
TRF No. IEC60335_2_40F
Page 83 of 97
19.11
Report No. 236145
TABLE: abnormal operation
The following fault conditions are introduced:
Test input (V)
P
240V 50Hz (at upper rated voltage)
Component
Fault condition
Result
Short circuit
Open circuit
Transformer
(secondary output)
S-c
-
- Thermal link for transformer open.
- Max. temp. of winding: 110°C
- No deterioration of insulation.
- No hazard.
Electrolytic capacitor
(CE101)
S-c
-
- Fuse (F100) open.
- No hazard.
Electrolytic capacitor
(CE101)
-
O-c
Electrolytic capacitor
(CE103)
S-c
-
Electrolytic capacitor
(CE103)
-
O-c
Electrolytic capacitor
(CE105)
S-c
-
Electrolytic capacitor
(CE105)
-
O-c
MICOM
(IC04, pin 43 - pin 42)
S-c
-
- Segment display error.
- After removal of short circuit, normal operation.
- No components damaged.
- No hazard.
Diode
(D104)
S-c
-
- Fuse (F100) open.
- No excessive temperature rises.
- No hazard.
Bridge diode
(BD101)
(pin1(+) - pin3(~))
S-c
-
- Fuses (F100) open.
- Bridge diode (BD71) damaged.
- No hazard.
Bridge diode
(BD101)
(pin2(-) – pin4(~))
S-c
-
- Fuses (F100) open.
- Bridge diode (BD71) damaged.
- No hazard.
- Normal operation, no components damaged.
- No hazard.
- Max. temp. of IC01 (KA7812): 120°C
- No excessive temperature rises.
- No hazard.
- Normal operation, no components damaged.
- No hazard.
- Max. temp. of IC02 (KA7805): 130°C
- No excessive temperature rises.
- No hazard.
- Normal operation, no components damaged.
- No hazard.
- Other part < 15W: no further tests
- S-c = Short-circuit, O-c = Open circuit, Dis = Disconnection, O-l = Overload, o/p = output
TRF No. IEC60335_2_40F
Page 84 of 97
19.14
Report No. 236145
P
TABLE: Abnormal operation
t1 (°C) ........................................................................ :
--

t2 (°C) ........................................................................ :
--

Temperature T of part / at :
T (°C)
Required T (°C)
--
--
--
--
--
--
supplementary information:
See appended table 19.5, 19.7, 19.10 and 19.11.
During the testing to cl. 19, no flame, no molten metal, no poisonous/ ignitable gas in hazardous amounts.
TRF No. IEC60335_2_40F
Page 85 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Type / model
Technical data
Standard
Mark(s) of
conformity1)
Fan motor for
indoor unit
DL12840SSBF
Brushless DC
type,
311Vd.c. 183W
Cu winding,
Cl. B (Cl. 130)
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
DL712840SSBG
Brushless DC
type,
311Vd.c. 183W
Cu winding,
Cl. B (Cl. 130)
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. Changzhou
ZWD-183Sinjun Motor Co., BA02
Ltd.
Brushless DC
type,
310Vd.c. 183W
Cl. B (Cl. 130)
IEC 60335-1
IEC 60335-2-40
Checked in
the appliance
Alt. Changzhou
ZWD-183Sinjun Motor Co., BA01
Ltd.
Brushless DC
type,
310Vd.c. 183W
Cl. B (Cl. 130)
IEC 60335-1
IEC 60335-2-40
Checked in
the appliance
300V, 30A
IEC 60335-1
IEC 60335-2-40
IEC 60998-1
Checked in the
appliance
VDE
DAF
300V, 25A
IEC 60335-1
IEC 60335-2-40
IEC 60998-1
Checked in the
appliance
VDE
DAF-(X)P
300V, 25A
IEC 60335-1
IEC 60335-2-40
IEC 60998-1
Checked in the
appliance
VDE
DAF-S(X)P
300V, 20A
IEC 60335-1
IEC 60335-2-40
IEC 60998-1
Checked in the
appliance
VDE
Alt. Zhejiang
JXW series
Changdecheng
Electric Appliances
Co., Ltd.
300V, 30A
IEC 60335-1
IEC 60335-2-40
IEC 60998-1
Checked in the
appliance
VDE
SPG Co., Ltd.
Alt. SPG Co., Ltd.
Terminal block 1 Nantong Huaguan JXW
Electric Co., Ltd.
Alt. Dong-A Bestech
Co., Ltd.
Terminal block 2 Dong-A Bestech
Co., Ltd.
Alt. Dong-A Bestech
Co., Ltd.
Thermal link
incorporated
with terminal
block
Tamura Thermal
Device Corp.
N1F
250V~ 1A
Tf: 86C
IEC 60691
VDE
EEV
(Electronic
expansion
valve)
Zhejiang Sanhua
Co., Ltd
DPF(O)4.0C04
12Vd.c.
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
EEV
(Electronic
expansion
valve)
Zhejiang Sanhua
Co., Ltd
DPF(O)3.2C08
12Vd.c.
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
TRF No. IEC60335_2_40F
Page 86 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Type / model
Technical data
Standard
Mark(s) of
conformity1)
Optional component: Package name, MDP-E075SEE3D
Drain pump
(optional)
Shin Han ElectroMechanics Co.,
Ltd
SDP series
12Vd.c.
Max. 4.0W
Brushless DC
type,
Cl. E (Cl. 120)
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
DS-7405S
FR-4, T1.6
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. KINGBOARD CO. KB-6150C
FR-4, T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. KINGBOARD
LAMINATES LTD
KB-6160C
FR-4, T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. Kunshan Suhang
Circuit Board Co.,
Ltd
SH-M1
CEM-3,
T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. Kunshan Huatao
Circuit Board Co.,
Ltd
HT-M
CEM-3,
T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
TE5 400
Series
250V~ T5A
IEC 60335-1
IEC 60335-2-40
IEC 60127-1
IEC 60127-3
Checked in the
appliance
VDE
Varistor
Thinking Electronic TVR 14561
(VA101, VA102) Industrial Co., Ltd
560V 4500A
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Amotech Co., Ltd
INR 14D561
560V, 4500A
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Ceramate Techn.
Co., Ltd.
GNR
14D561K
560V 4500A
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Amotech Co., Ltd
INR 14D621K
620V, 4500A
385Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Components on Main PCB
PCB
Fuse 1
(F100)
Doosan/Kolon
Littelfuse Inc.
TRF No. IEC60335_2_40F
Page 87 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Varistor
(VA103)
Type / model
Thinking Electronic TVR 14D681
Industrial Co., Ltd
Technical data
Standard
Mark(s) of
conformity1)
680V, 4500A
420Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Amotech Co., Ltd
INR 14D681K
680V, 4500A
420Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Ceramate Techn.
Co., Ltd.
GNR
14D681K
680V, 5000A
420Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Choke coil
(L101)
Sangshin
Electronics Co.,
Ltd
SS-0800
250V~ 50/60Hz,
3A, 8mH
- Magnet wire:
UEW (105C)
- Bobbin: V-0
- Base: V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Surge absorber
(DSA101)
Mitsubish
Materials Corp.
DSA-332M
3300V ±20%
Insulation
resistance:
Min.100MΩ
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
DA38-362M
3600V ±20%
Insulation
resistance:
Min.100MΩ
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
PCX2 337
Series
275V~ 0.33uF
X2, T85
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
ENEC 14
(SEMKO)
Alt. Ultra Tech Xiphi
HQX Series
Enterprise Co., Ltd
250/ 275V~
0.33uF
X2, T100
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
Alt. Joey Electronics
(Dongguan) Co.,
Ltd
MPX Series
275V~ 0.33uF
X2, T100
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
SC Series
1nF 250V/ 400V
0.47nF 250V
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
DA Series
1nF 250V
0.47nF 250V
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
Nemko
Alt. Mitsubish
Materials Corp.
X-Capacitor
(CX101)
Pilkor Electronics
Ltd.
Y-capacitor
SamWha
(CY101, CY102) Capacitor Co., Ltd
Alt. DONG IL
Electronics Co.,
Ltd.
TRF No. IEC60335_2_40F
Page 88 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Type / model
Technical data
Standard
Mark(s) of
conformity1)
Photocoupler
(PC101)
Toshiba
Corporation
TLP181
-25 – 100C
Viso= 3750Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. Toshiba
Corporation
TLP180
-25 – 100C
Viso= 3750Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. NEC Corporation
PS2565-1
-55 – 100C
Viso= 3750Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. Toshiba
Corporation
TLP351
-40 – 100C
Viso= 3750Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. SHARP Corp.
PC814
-30 – 100C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. SHARP Corp.
PC123
-30 – 100C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. Toshiba
Corporation
TLP421
(D4-BL)
-55 – 100C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. LITE-ON
Technology Corp.
LTV-356
-30 – 110C
Viso= 3750Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. Cosmo Electronics KPC357NT0C -55 – 115C
Corporation
Viso= 3750Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
-55 – 115C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Photocoupler
(PC102)
Bridge diode
(BD101)
Cosmo Electronics K10104C
Corporation
Alt. EVERLIGHT
EL816
-55 – 110C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. LITE-ON
Technology Corp.
LTV-817S
-30 – 110C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
Alt. NEC Corporation
PS2561A
-55 – 100C
Viso= 5000Vrms
IEC 60335-1
IEC 60335-2-40
EN 60747-5-2
Checked in the
appliance
VDE
D3SB60
600V 4A
150C
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
PCJ112D3MH
250V~, 3A,
T90, 10E4
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Shindengen
Electronics Ltd.
Relay
Tyco Electronics
(RY101, RY702) (Shenzhen) Co.,
Ltd.
TRF No. IEC60335_2_40F
Page 89 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Type / model
Technical data
Standard
Mark(s) of
conformity1)
Alt. Fujitsu Component FTRLimited
F3AA012E
250V~, 3A,
T70, 20E4
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. Tyco Electronics
(Shenzhen) Co.,
Ltd.
EJ00-1A4D012-F
250V~, 3A,
T70, 3E4
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. Tyco Electronics
(Shenzhen) Co.,
Ltd.
OJ-SS-112DM 250V~, 5A,
T70, 6E4
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE, TUV Rh
Alt. In & Out Electronic GC-12VDCCorporation
A45
250V~, 5A,
T75, 1E5
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. Xiamen Hongfa
Electroacoustics
HF46F12HS1T
250V~, 5A,
T85, 2E5
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. OMRON Corp.
G5NB-1A-E
250V~, 5A,
T85, 1E5
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. OMRON Corp.
G5T-1A
250V~, 5A,
T70, 3E4
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. Panasonic Electric ALD112
Works Co., Ltd
250V~ 3A,
T70, 2E5
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
Alt. Panasonic Electric ALDP112
Works Co., Ltd
250V~ 5A,
T70, 2E5
IEC 60335-1
IEC 60335-2-40
IEC 61810-1
Checked in the
appliance
VDE
250V~ 7.5A
-55 – 125 C
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
AC Connector
YeonHo
(CN101, CN702, Electronics Co.
CN703)
Y(H)W396
Series
Reactor
DB27-00041B 5mH, 10A,
50/60Hz
Cl. H (Cl.180)
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. Qingdao Yunlu
DB27-00041B 5 mH, 10 A,
Enegy Technology
50/60 Hz
Co., Ltd.
Cl. H (Cl.180)
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
IEC 60335-1
IEC 60335-2-40
IEC 61558-1
IEC 61558-2-16
Checked in the
appliance
Switching
transformer
(T101)
Foshan Welling
Electronic And
Electric Co.,Ltd
Wonkyung
Electronics Co.,
Ltd
TRF No. IEC60335_2_40F
DB26-00131A - 490uH
- Core: EE2218
- Bobbin:
Phenolic, V-0
- Winding: 2UEW
- Cl. B (Cl. 130)
Page 90 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Standard
Mark(s) of
conformity1)
DB26-00131A - 530uH
- Core: EE2525
- Bobbin:
Phenolic, V-0
- Winding: 2UEW
- Cl. B (Cl. 130)
IEC 60335-1
IEC 60335-2-40
IEC 61558-1
IEC 61558-2-16
Checked in the
appliance
DS-7405S
FR-4, T1.6
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. KINGBOARD
LAMINATES LTD
KB-6150
FR-4, T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. Kunshan Suhang
Circuit Board Co.,
Ltd
SH-M1
CEM-3,
T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
Alt. Kunshan Huatao
Circuit Board Co.,
Ltd
HT-M
CEM-3,
T1.6, V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
250V~ T5A,
250V~ T3.15A
IEC 60335-1
IEC 60335-2-40
IEC 60127-1
IEC 60127-3
Checked in the
appliance
VDE
Alt. Namyang
Electronics Co.,
Ltd
Type / model
Technical data
Components on BLDC PCB
PCB
Fuse
(F701)
Varistor
(VA71)
Doosan/Kolon
Cooper Bussmann S506 series
LLC
Alt. Littelfuse Inc.
218 series
250V~ T5A,
250V~ T3.15A
IEC 60335-1
IEC 60335-2-40
IEC 60127-1
IEC 60127-3
Checked in the
appliance
VDE
Alt. Orisel Co., Ltd.
50T/52T
series
250V~ T5A,
250V~ T3.15A
IEC 60335-1
IEC 60335-2-40
IEC 60127-1
IEC 60127-3
Checked in the
appliance
VDE
560V 4500A
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Thinking Electronic TVR 14561
Industrial Co., Ltd
Alt. Amotech Co., Ltd
INR 14D561
560V, 4500A
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Ceramate Techn.
Co., Ltd.
GNR
14D561K
560V 4500A
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
TRF No. IEC60335_2_40F
Page 91 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Type / model
Technical data
Standard
Mark(s) of
conformity1)
INR14D621K
620V, 4500A
385Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Thinking Electronic TVR 14D681
Industrial Co., Ltd
680V, 4500A
420Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Amotech Co., Ltd
INR 14D681K
680V, 4500A
420Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Ceramate Techn.
Co., Ltd.
GNR
14D681K
680V, 5000A
420Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Samwha Capacitor SVC561D-14A 560V 4500A
Co., Ltd.
350Vrms
T85
IEC 60335-1
IEC 60335-2-40
IEC 61051-1
IEC 61051-2/ -2-2
CECC 42200
CECC 42201
Checked in the
appliance
VDE
Alt. Amotech Co., Ltd
Choke coil
(FT71)
Sangshin
Electronics Co.,
Ltd
SSC2208140
B
250V~ 50/60Hz,
5A, 14mH
- Bobbin: V-0
- Base: V-0
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
X-Capacitor
(X701, X702)
Pilkor Electronics
Ltd.
PCX2 337
Series
275V~ 0.33uF
275V~ 0.68uF
X2, T85
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
ENEC 14
(SEMKO)
Alt. Ultra Tech Xiphi
HQX Series
Enterprise Co., Ltd
275V~ 0.33uF
275V~ 0.68uF
X2, T85
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
Alt. Joey Electronics
(Dongguan) Co.,
Ltd
MPX Series
275V~ 0.33uF
275V~ 0.68uF
X2, T85
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
Alt. Sunil Electronics
Ind Co., Ltd.
435D Series
275V~ 0.33uF
275V~ 0.68uF
X2, T85
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
TRF No. IEC60335_2_40F
Page 92 of 97
24.1
Report No. 236145
P
TABLE: Components
Object / part No. Manufacturer/
trademark
Type / model
Y-capacitor
(Y701, Y702)
TDK corporation
Standard
Mark(s) of
conformity1)
CS, CD Series 2.2nF 400V
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
Alt. Wanming
Electronics Co.,
Ltd.
HM,HJ-Series 2.2nF 400V
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
Alt. SamWha
Capacitor Co., Ltd
SC Series
2.2nF 400V
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
Alt. DONG IL
Electronics Co.,
Ltd.
DA Series
2.2nF 400V
IEC 60335-1
IEC 60335-2-40
IEC 60384-14
Checked in the
appliance
VDE
IEC 60335-1
IEC 60335-2-40
Checked in the
appliance
AC Connector
(CN71, CN72)
YeonHo
Electronics Co.
1)
Technical data
YW396 Series 250V~ 7A
-55 – 125 C
An asterisk indicates a mark which assures the agreed level of surveillance
supplementary information:
TRF No. IEC60335_2_40F
Page 93 of 97
28.1
Report No. 236145
P
TABLE: Threaded part torque test
Threaded part identification
Diameter of thread
(mm)
Column number
(I, II, or III)
Applied torque (Nm)
Metal screws
- for interconnection cord
connection on terminal block
>3,6 and  4,1
(Measured: 3,9)
II
1,2
Metal screws
- for earthing provision
>3,6 and  4,1
(Measured: 3,9)
II
1,2
supplementary information:
29.1
P
TABLE: Clearances
Overvoltage category ...... :

Category II
Type of insulation:
Rated impulse
voltage (V)
Min. cl
(mm)
330
0,5 1)
500
0,5
1)
800
0,5 1)
1), 2)
Basic
Functional
Supplementary
Reinforced
Verdict / Remark
-
-
-
-
N/A
0,5
0,5
-
-
P
-
-
-
-
N/A
-
-
-
-
N/A
1500
0,5
2500
1,5 2)
1,5
1,5
1,5
-
P
4000
3,0
2)
-
-
-
3,0
P
5,5
2)
-
-
-
-
N/A
8,0
2)
-
-
-
-
N/A
-
-
-
-
N/A
6000
8000
10000
11,0
2)
1)
Value is increased to 0,8 mm for pollution degree 3
If the construction is affected by wear, by distortion, by movement of the parts or during assembly, the
value is increased by 0,5 mm
supplementary information:
2)
TRF No. IEC60335_2_40F
Page 94 of 97
29.2
Report No. 236145
P
TABLE: Creepage distances, basic, supplementary and reinforced insulation
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
2
3
Type of insulation
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb
B*)
S*)
R*)
Verdict
50
0,2
0,6
0,9
1,2
1,5
1,7
1,9
1,2


P
50
0,2
0,6
0,9
1,2
1,5
1,7
1,9

1,2

P
50
0,4
1,2
1,8
2,4
3,0
3,4
3,8


2,4
P
50 and 125
0,3
0,8
1,1
1,5
1,9
2,1
2,4


N/A
50 and 125
0,3
0,8
1,1
1,5
1,9
2,1
2,4


N/A
50 and 125
0,6
1,6
2,2
3,0
3,8
4,2
4,8


125 and 250
0,6
1,3
1,8
2,5
3,2
3,6
4,0
2,5


P
125 and 250
0,6
1,3
1,8
2,5
3,2
3,6
4,0

2,5

P
125 and 250
1,2
2,6
3,6
5,0
6,4
7,2
8,0


5,0
P
250 and 400
1,0
2,0
2,8
4,0
5,0
5,6
6,3
4,0


P
250 and 400
1,0
2,0
2,8
4,0
5,0
5,6
6,3

4,0

P
250 and 400
2,0
4,0
5,6
8,0
10,0
11,2
12,6


8,0
P
400 and 500
1,3
2,5
3,6
5,0
6,3
7,1
8,0


N/A
400 and 500
1,3
2,5
3,6
5,0
6,3
7,1
8,0


N/A
400 and 500
2,6
5,0
7,2
10,0
12,6
14,2
16,0

500 and 800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
500 and 800
1,8
3,2
4,5
6,3
8,0
9,0
10,0

500 and 800
3,6
6,4
9,0
12,6
16,0
18,0
20,0

800 and 1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
800 and 1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5

800 and 1000
4,8
8,0
11,2
16,0
20,0
22,0
25,0

1000 and 1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
1000 and 1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0

1000 and 1250
6,4
10,0
14,2
20,0
25,0
28,0
32,0

1250 and 1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
1250 and 1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0

1250 and 1600
8,4
12,6
18,0
25,0
32,0
36,0
40,0

1600 and 2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
1600 and 2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0

1600 and 2000
11,2
16,0
22,0
32,0
40,0
44,0
50,0

TRF No. IEC60335_2_40F
N/A


N/A

N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A



N/A

N/A

N/A
N/A
Page 95 of 97
29.2
Report No. 236145
P
TABLE: Creepage distances, basic, supplementary and reinforced insulation
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
2
3
Type of insulation
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb
B*)
2000 and 2500
7,5
10,0
14,0
20,0
25, 0
28,0
32,0
2000 and 2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0

2000 and 2500
15,0
20,0
28,0
40,0
50,0
56,0
64,0

2500 and 3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
2500 and 3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0

>2500 and 3200
20,0
25,0
36,0
50,0
64,0
72,0
80,0

3200 and 4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
3200 and 4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0

3200 and 4000
25,0
32,0
44,0
64,0
80,0
90,0
100,0

4000 and 5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
4000 and 5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0

4000 and 5000
32,0
40,0
56,0
80,0
100,0
112,0
126,0

5000 and 6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
5000 and 6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0

5000 and 6300
40,0
50,0
72,0
100,0
126,0
142,0
160,0

6300 and 8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
6300 and 8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0

6300 and 8000
50,0
64,0
90,0
126,0
160,0
180,0
200,0

8000 and 10000
32,0
40,0
56,0
80,0
100,0
110,0
125,0
8000 and 10000
32,0
40,0
56,0
80,0
100,0
110,0
125,0

8000 and 10000
64,0
80,0
112,0
160,0
200,0
220,0
250,0

10000 and 12500 40,0
50,0
71,0
100,0
125,0
140,0
160,0
10000 and 12500 40,0
50,0
71,0
100,0
125,0
140,0
160,0

10000 and 12500 80,0
100,0
142,0
200,0
250,0
280,0
320,0

*), B=Basic, S=Supplementary and R=Reinforced
supplementary information:
TRF No. IEC60335_2_40F
Verdict
S*)
R*)


N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A


N/A

N/A

N/A



N/A

N/A

N/A
N/A
Page 96 of 97
29.2
Report No. 236145
TABLE: Creepage distances, basic, supplementary and reinforced insulation
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
Verdict / Remark
2
3
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb
50
0,2
0,6
0,8
1,1
1,4
1,6
1,8
P (min. 1,1)
50 and 125
0,3
0,7
1,0
1,4
1,8
2,0
2,2
N/A
125 and 250
0,4
1,0
1,4
2,0
2,5
2,8
3,2
P (min. 2,0)
250 and 400
0,8
1,6
2,2
3,2
4,0
4,5
5,0
P (min. 3,2)
400 and 500
1,0
2,0
2,8
4,0
5,0
5,6
6,3
N/A
500 and 800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
N/A
800 and 1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
N/A
1000 and 1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
N/A
1250 and 1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
N/A
1600 and 2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
N/A
2000 and 2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0
N/A
2500 and 3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
N/A
3200 and 4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
N/A
4000 and 5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
N/A
5000 and 6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
N/A
6300 and 8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
N/A
8000 and 10000
32,0
40,0
56,0
80,0
100,0
110,0
125,0
N/A
10000 and 12500 40,0
50,0
71,0
100,0
125,0
140,0
160,0
N/A
supplementary information:
TRF No. IEC60335_2_40F
P
Page 97 of 97
30.1
Report No. 236145
TABLE: Ball pressure
Part
P
Test temperature
(C)
Impression diameter
(mm)
Allowed impression
diameter (mm)
75
< 1,4
2,0
X-capacitor
125
1,5
2,0
Fuse holder
125
1,6
2,0
Switching transformer bobbin
125
1,4
2,0
Choke coil bobbin
125
1,6
2,0
Relay
125
1,6
2,0
PCB
125
< 1,4
2,0
Terminal block
125
< 1,4
2,0
AC connector
125
1,5
2,0
Cord anchorage
supplementary information:
30.2
TABLE: glow-wire test
P
Parts
temperature ( °C)
verdict
550
P
X-capacitor
850 *) / 750 **)
P
Fuse holder
850 *) / 750 **)
P
Switching transformer bobbin
850 *) / 750 **)
P
Choke coil bobbin
850 *) / 750 **)
P
Relay
850 *) / 750 **)
P
PCB
850 *) / 750 **)
P
Terminal block
850 *) / 750 **)
P
AC connector
850 *) / 750 **)
P
Cord anchorage
supplementary information:
*) Glow-wire test at 850 °C according to the IEC 60695-2-11.
No parts exceeding 60 s (te < 60 s) and no parts igniting the layer below.
**) Glow-wire test at 750 °C according to the IEC 60695-2-11.
== END of TEST REPORT ==
TRF No. IEC60335_2_40F
Page 1 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
ATTACHMENT TO TEST REPORT IEC 60335-2-40
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Part 2-40: Particular requirements for electrical heat pumps, air conditioners and
dehumidifiers
Differences according to ............... :
EN 60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 +
A1:2006 + A2:2009 with
EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 +
A13:2008
Attachment Form No. .................... :
EU_GD_IEC60335_2_40F
Attachment Originator ................... :
VDE
Master Attachment ........................ :
Date 2009-11
Copyright © 2009 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
Group Differences / CENELEC COMMON MODIFICATIONS to IEC 60335-1, IEC 60335-2-40
7.12.1
Installation instructions for appliances intended to be Not exceeding 10mA.
permanently connected to fixed wiring, and have
leakage current exceed 10 mA, state that installation
of residual current device (RCD) having rated
residual operating current not exceeding 30 mA is
advisable (EN 60335-2-40)
N/A
For appliances not accessible to the general public
and which are intended to be permanently
connected to fixed wiring and which may have
leakage currents exceeding 10 mA, the installation
instructions shall specify the rating of the residual
current device (RCD) to be installed
(EN 60335-2-40/A12)
Not exceeding 10mA.
N/A
13.2
Leakage current measurements (EN 60335-2-40)
(See appended table in main
test report.)
15.1
Enclosure provides the degree of moisture protection No IP degree, IPX0.
according to classification of appliance
(EN 60335-2-40/A2)
N/A
Compliance checked as specified in clause 15.1.1,
taking into account 15.1.2, followed by the electric
strength test of 16.3 (EN 60335-2-40/A2)
N/A
15.1.1
IPX0
P
No trace of water on insulation which can result in a
reduction of clearances and creepage distances
below values specified in clause 29
(EN 60335-2-40/A2)
N/A
Appliances, other than IPX0, subjected to tests as
IPX0
specified in IEC 60529 (EN 60335-2-40/A2) ............. :
N/A
Page 2 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
15.1.2
Requirement – Test
16.2
Verdict
Water valves containing in external hoses for
No such water valves.
connection of an appliance to water mains,
subjected to the test as specified for IPX7 appliances
(EN 60335-2-40/A2)
N/A
Hand-held appliance turned continuously through
most unfavourable positions during test
N/A
Built-in appliances installed according instructions
(EN 60335-2-40/A2)
15.2
Result – Remark
IPX0
N/A
Appliances placed or used on the floor or table
placed on a horizontal unperforated support
(EN 60335-2-40/A2)
N/A
Appliances normally fixed to a wall and appliances
with pins for insertion into socket-outlets are
mounted on a wooden board (EN 60335-2-40/A2)
N/A
For IPX3 appliances, the base of wall mounted
appliances is placed at the same level as the pivot
axis of the oscillating tube (EN 60335-2-40/A2)
N/A
For IPX4 appliances, horizontal centre line of
appliance is aligned with pivot axis of oscillating tube
(EN 60335-2-40/A2)
N/A
However, for appliances normally used on floor or
table, movement is limited to two times 90 ° for a
period of 5 min, support being placed at the level of
pivot axis of oscillating tube (EN 60335-2-40/A2)
N/A
Appliances normally fixed to a ceiling are mounted
underneath a horizontal unperforated support, pivot
axis of oscillating tube located at level of underside
of support (EN 60335-2-40/A2)
N/A
IPX4 appliances, movement of tube is limited to two
times 90 ° from vertical for a period of 5 min
(EN 60335-2-40/A2)
N/A
Wall-mounted appliances, take into account distance
to floor stated in instructions (EN 60335-2-40/A2)
N/A
Appliances with type X attachment fitted with a
flexible cord as described (EN 60335-2-40/A2)
N/A
Detachable parts tested as specified
(EN 60335-2-40/A2)
N/A
Appliances proof against humid conditions
(EN 60335-2-40)
Considered.
P
Humidity test for 48 h in a humidity cabinet
(EN 60335-2-40)
For 48h at 24°C, 95% R.H.
P
Appliance withstands tests of clause 16
(EN 60335-2-40)
No excessive leakage current.
No breakdown.
P
Leakage current measurements (EN 60335-2-40)
(See appended table in main
test report.)
P
Page 3 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
24.1.7
Remote operation via telecommunication network,
No such remote operation.
relevant standards for telecommunication interface
circuitry in appliance EN 41003 and
EN 60950-1:2006, Subclause 6.3 (EN 60335-1/A13)
N/A
25.6
Supply cords of single-phase portable appliances having a rated current not
exceeding 16 A, fitted with a plug complying with the following standard sheets of
IEC 60083:1975:
—
- class I appliances: standard sheet C2b, C3b or C4 : Stationary/ Fixed appliance.
N/A
- class II appliances: standard sheet C5 or C6 ......... :
N/A
25.7
Result – Remark
Supply cords being one of following types:
- ordinary polychloroprene sheathed flexible cord (at
least 60245 IEC 57) (H05RN-F)
Verdict
—
1. Not checked in this test
report.
N/A
2. The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
Supply cords having high flexibility, not lighter than:
—
- rubber insulated and sheathed cord (60245 IEC 86)
(H03RR-H)
N/A
- rubber insulated, crosslinked PVC sheathed cord
(60245 IEC 87) (H03RV4-H)
N/A
- crosslinked PVC insulated and sheathed cord
(60245 IEC 88) (H03V4V4-H).
N/A
29.3
Replace third dashed item by:
- an assessment of thermal quality of material
combined with an electric strength test, in
accordance with clause 29.3.3, and for accessible
reinforced insulation consisting of a single layer,
measurement in accordance with clause 29.3.Z1
(EN 60335-1/A12)
N/A
29.3.Z1
Accessible reinforced insulation consisting of a
single layer, thickness of layer complies with
table Z1; rated voltage (V); overvoltage category;
thickness (mm) (EN 60335-1/A12) ............................ :
N/A
GG.2
Requirements for charge limits in unventilated areas Intended for the use of a non(EN 60335-2-40/A1)
flammable refrigerant.
N/A
GG.Z1
Non fixed factory sealed single package units with a
charge amount of m 1 < M ≤ 2 x m 1
(EN 60335-2-40/A1)
N/A
Page 4 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
ZC
ANNEX ZC (NORMATIVE) (EN 60335-1, EN 60335-2-40)
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS
—
Normative references to international publications
with their corresponding European publications
(EN 60335-1/A1, EN 60335-1/A2, EN 60335-2-40)
P
ANNEX ZD (INFORMATIVE) (EN 60335-1, EN 60335-2-40)
IEC AND CENELEC CODE DESIGNATIONS FOR FLEXIBLE CORD
—
List of code designations for different types of
flexible cords
P
ZD
Result – Remark
Verdict
National Differences for Austria
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for Belgium
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C2b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for Denmark
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
7.12
Requirements regarding marking tag of power
supply cord and connection of earthing wire for
class I appliances delivered without plug
—
N/A
Page 5 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
25.6
Supply cords of single-phase portable appliances having a rated current not
exceeding 13 A provided with a plug according to following:
- Class I appliances: Section 107-2-D1, ed.3 1998,
standard sheet DK 2-1a
Result – Remark
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
Appliances covered by a Part 2 of EN 60335, also
plugs in accordance with Section 107-2-D1, ed.3,
1998, standard sheet C2b, C3b or C4 are allowed
Verdict
—
N/A
N/A
Class II appliances: Section 107-2-D1, ed.3 1998,
standard sheet C1b, C5, C6, DKA 2-1a and
DKA 2-1b
N/A
Stationary single-phase appliances, having a rated
current not exceeding 13 A, and provided with a
supply cord and a plug, the plug is in accordance
with the requirements above
N/A
Multi-phase appliances and single-phase appliances having a rated current
exceeding 13 A, and provided with a supply cord and a plug, plug is in accordance
with requirements below:
- Class I appliances: Section 107-2-D1, standard
sheet DK 6-1a / EN 60309-2, standard sheet 2-II,
2-IV
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
- Class II appliances: Section 107-2-D1, standard
sheet DK 6-1a / EN 60309-2, standard sheet 2-II,
2-IV, the earthing contact not being connected
N/A
Current for plug not exceeding values specified;
standard sheet (no.); current (A)................................ :
N/A
Page 6 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
National Differences / Deviations for Finland
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for France
—
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
22.2
Second paragraph of this subclause, dealing with
single-phase, permanently connected class I
appliances having heating elements, not applicable
due to supply system
No heating elements.
N/A
25.6
Plugs according to standard sheet C2b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
N/A
National Differences / Deviations for Germany
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
ZB
ANNEX ZB (INFORMATIVE), A-DEVIATIONS (EN 60335-1, EN 60335-2-40)
29.3
GERMANY: Third dashed item not applicable for
appliances where the insulation is accessible.
Additional measures, such as multi-layered
insulation or adequate thickness, taken
(EN 60335-1/A1)
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
—
N/A
Page 7 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
National Differences / Deviations for Iceland
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for Ireland
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
Only plugs according to standard sheets B2 and C5
allowed (see also annex ZB)
25.8
1,25 mm²
> 13 A and ≤ 16 A
1,5 mm²
N/A
N/A
Replacement of line for 10 A and 16 A by:
> 10 A and ≤ 13 A
—
—
N/A
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
ZB
ANNEX ZB (INFORMATIVE), A-DEVIATIONS (EN 60335-1, EN 60335-2-40)
25.6
These regulations apply to all plugs for domestic use No plugs.
at a voltage of not less than 200 V and allow only
plugs complying with I.S. 401:1997, or equivalent, to
be fitted to domestic appliances
N/A
—
N/A
Page 8 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
National Differences / Deviations for Italy
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
Only plugs listed in CENELEC Report
R0BT-005:2001 allowed
Deleted.
—
N/A
—
ZB
ANNEX ZB (INFORMATIVE), A-DEVIATIONS (EN 60335-1, EN 60335-2-40)
—
7.1
Voltage is 220 V/380 V
P
220V covered.
Rated: 220-240V~ 50Hz
National Differences / Deviations for Luxembourg
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for Netherlands
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
Page 9 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
National Differences / Deviations for Norway
—
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
22.2
Second paragraph of this subclause, dealing with
single-phase, permanently connected class I
appliances having heating elements, not applicable
due to supply system
No heating elements.
N/A
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
N/A
National Differences / Deviations for Portugal
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for Spain
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C2b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
Plugs according to standard sheet C3b not allowed
- according to UNE-EN 50075
N/A
N/A
Appliances for household use, only following plugs are allowed:
- according to UNE 20315: ESC 10-1b, C2b, C4, C6
or ESB 25-5b
—
No plugs.
—
N/A
N/A
Page 10 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
National Differences / Deviations for Sweden
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C2b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
National Differences / Deviations for Switzerland
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C3b not allowed
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
Supply cords of portable household and similar electrical appliances having a rated
current not exceeding 10 A, provided with a plug complying with SEV 1011 or
IEC 60884-1 and one of following dimension sheets:
- SEV 6532-2.1991, plug type 15, 3P+N+PE,
250/400 V, 10 A
Stationary appliance,
Exceeding 10A.
—
N/A
—
N/A
- SEV 6533-2.1991, plug type 11, L+N, 250 V, 10 A
N/A
- SEV 6534-2.1991 plug type 12, L+N+PE, 250 V,
10 A
N/A
ZB
ANNEX ZB (INFORMATIVE), A-DEVIATIONS (EN 60335-1, EN 60335-2-40)
4
Information about batteries with carbon-zinc and
alkali-manganese
No batteries.
—
N/A
Page 11 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
National Differences / Deviations for United Kingdom
ZA
ANNEX ZA (NORMATIVE), SPECIAL NATIONAL CONDITIONS (EN 60335-1,
EN 60335-2-40)
25.6
Plugs according to standard sheet C2b not allowed
25.8
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
—
N/A
Plugs according to standard sheet C3b not allowed
N/A
Only plugs according to standard sheets B2 and C5
allowed (see also annex ZB)
N/A
Replacement of line for 10 A and 16 A by:
> 10 A and ≤ 13 A
1,25 mm²
> 13 A and ≤ 16 A
1,5 mm²
—
N/A
No plugs.
The manufacturer, service
agent or similarly qualified
person shall use a proper
cross sectional area of supply
cord and interconnection cord
referring to an installation
manual.
ZB
ANNEX ZB (INFORMATIVE), A-DEVIATIONS (EN 60335-1, EN 60335-2-40)
25.6
These regulations apply to all plugs for domestic use No plugs.
at a voltage of not less than 200 V and allow only
plugs to BS 1363 to be fitted to domestic appliances.
It also allows plugs to BS 4573 and standard
sheet C5 to be fitted to shavers and toothbrushes.
ZAA
ANNEX ZAA (INFORMATIVE) (EN 60335-2-40/A11)
THE RELEVENCE OF THE PRESSURE EQUIPMENT DIRECTIVE
Refrigerating systems having a pressure greater
than 0,05 MPa are considered to be assemblies
falling within the scope of the Pressure Equipment
Directive, 97/23/EC. However, according to
Article 1, item 3.6 of the directive, equipment
classified no higher than category I and covered by
the low voltage directive is excluded from its scope.
(EN 60335-2-40/A11)
N/A
—
N/A
—
N/A
Page 12 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
According to guideline 1/39 of the directive, this
exclusion applies to both components and
assemblies (refrigerant circuits). This applies to
appliances containing vessels (e.g. compressors,
receivers) or piping with limits in accordance with
the following (EN 60335-2-40/A11):
Verdict
N/A
Vessels (EN 60335-2-40/A11)
—
- dangerous refrigerants (Annex II, Table 1) (EN 60335-2-40/A11):
—
- volume not exceeding 1 l, or
(EN 60335-2-40/A11)
N/A
- pressure x volume not exceeding 5 MPa l
(EN 60335-2-40/A11)
N/A
- non-dangerous refrigerants (Annex II, Table 2) (EN 60335-2-40/A11):
—
- volume not exceeding 1 l, or
(EN 60335-2-40/A11)
N/A
- pressure x volume not exceeding 20 MPa l
(EN 60335-2-40/A11)
N/A
Piping (EN 60335-2-40/A11)
—
- dangerous refrigerants (Annex II, Table 6) (EN 60335-2-40/A11):
—
- numerical designation not exceeding 25, or
(EN 60335-2-40/A11)
N/A
- pressure not exceeding 1 MPa and numerical
designation not exceeding 100, or
(EN 60335-2-40/A11)
N/A
- pressure exceeding 1 MPa and pressure x
numerical designation not exceeding 100 MPa
(EN 60335-2-40/A11).
N/A
- non-dangerous refrigerants (Annex II, Table 7) (EN 60335-2-40/A11):
—
- numerical designation not exceeding 100, or
(EN 60335-2-40/A11)
N/A
- pressure x numerical designation not exceeding
350 MPa (EN 60335-2-40/A11).
N/A
For other components, the most onerous limit of the
two applies (EN 60335-2-40/A11)
N/A
The volume is the internal volume of the vessel and
includes the volume of pipework up to the first
connection. It excludes the volume of fixed internal
parts (EN 60335-2-40/A11)
N/A
The pressure is the maximum pressure the vessel
or piping system is exposed to, as specified by the
manufacturer of the appliance
(EN 60335-2-40/A11)
N/A
Page 13 of 13
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 1
EN 60335-1, EN 60335-2-40
Clause
Requirement – Test
Result – Remark
Verdict
The numerical designation designates the size
common to all components in the piping system
(EN 60335-2-40/A11)
N/A
If any component exceeds the limits given above,
the appliance has to comply with the directive. The
technical requirements are given in Annex I and the
conformity assessment tables and procedures in
Annexes II and III of the directive
(EN 60335-2-40/A11)
N/A
Commonly used dangerous refrigerants, identified
as Group 1 in the directive, are listed in table ZAA.1
(EN 60335-2-40/A11)
N/A
Commonly used non-dangerous refrigerants,
identified as Group 2 in the directive, are listed in
table ZAA.2 (EN 60335-2-40/A11)
N/A
Page 1 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 2
ATTACHMENT TO TEST REPORT IEC 60335-2-40
National Difference of Australia (AU) in the IECEE Online Bulletin
Part 2-40: Particular requirements for electrical heat pumps, air conditioners and
dehumidifiers
This attachment is based on the fact as following;
National Difference of Australia (AU) in the IECEE Online Bulletin. (http://www.iecee.org)
No.
IEC standard
National standard reference
1
IEC 60335-1 (Fourth edition); am1; am2
AS/NZS 60335.1: 2002
Last modification: 2010-04-19
2
IEC 60335-2-40 (Fourth edition); am1; am2
AS/NZS 60335.2.40: 2006
No national deviation for Australia (AU).
Page 2 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 2
National Difference of Australia (AU)
AS/NZS 60335.1:2002 corresponding to IEC 60335-1:2002; am1; am2
Clause
Requirement – Test
Result
5.2
Replace the last paragraph of NOTE 1 with the
following variation:
If the tests of annex H are carried out, one switch or
one additional appliance is needed.
5.8.1
Replace with the following variation:
Appliances for a.c. only are tested with a.c. at 50
Hz, and those for a.c. and d.c. are tested at a.c. 50
Hz or d.c., whichever is the more unfavourable
supply.
5.201
For Australia the following applies:
For appliances, other than class III appliances, that are intended for connection to
the supply mains and that are not marked with
Verdict
N/A
Rated: 220-240V~ 50Hz
Tested with a.c. at 50Hz.
– a rated voltage of at least 240 V for single-phase
appliances and at least 415 V for three-phase
appliances, or
P
—
N/A
– a rated voltage range that includes 240 V for
Rated: 220-240V~ 50Hz
single-phase appliances and 415 V for three-phase
appliances,
P
the rated voltage is equal to 240 V for single-phase Upper limit: 240V~ 50Hz
appliances and 415 V for three-phase appliances,
and the upper limit of the rated voltage range is
equal to 240 V for single-phase appliances and
415 V for three-phase appliances.
P
In addition, the rated current or rated power input is
equal to the calculated value corresponding to 240
V for single-phase appliances and 415 V for threephase appliances as appropriate.
N/A
NOTE 1 Example of calculation
If the appliance is marked with a rated voltage of
230 V and a rated current "A" or a rated power
input "P", it will be tested as if it is marked with a
rated voltage of 240 V and a rated current of A x
(240/230) or a rated power input of P x (240/230)2.
—
6.1
Replace the requirement with the following
variation:
Appliances shall be of one of the following classes
with respect to protection against electric shock:
class I, class II, class III.
7.1
After the first paragraph of the requirement insert the following variation:
Appliances intended for connection to the supply mains, other than class III
appliances, shall be marked with
– a rated voltage of at least:
230 V for single phase appliances;
400 V for polyphase appliances, or
Class I appliance.
P
—
N/A
Page 3 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 2
National Difference of Australia (AU)
AS/NZS 60335.1:2002 corresponding to IEC 60335-1:2002; am1; am2
Clause
Requirement – Test
Result
7.13
Rated: 220-240V~ 50Hz
– a rated voltage range that includes:
230 V for single phase appliances;
400 V for polyphase appliances.
Replace the requirement with the following
In English.
variation:
Instructions and other text required by this standard
shall be written in English.
Verdict
P
P
Table 3
After the second row in table 3 insert the following
variation:
Insulated pins of appliances with pins
for insertion into socket-outlets………….
45
No socket-outlets.
N/A
22.3
Replace the first paragraph of the test specification
with the following variation:
Compliance is checked by inserting the pins of the
appliance into a socket-outlet capable of accepting
a plug complying with Figure 2.1(a) of AS/NZS
3112. The socket-outlet has a horizontal pivot at a
distance of 8 mm behind the engagement face of
the socket-outlet and in the plane of the lower
intersection of the centre lines of the contact
apertures.
No socket-outlets.
N/A
22.201
After Clause 22.45 insert the following variations:
22.201 VOID
22.202
Appliances having integral pins for insertion into
socket outlets shall comply with the appropriate
requirements of AS/NZS 3112.
—
No socket-outlets.
N/A
Compliance with checked as specified in Annex J of
AS/NZS 3112
N/A
NOTE 1 Clause J.2.2.3 (Internal connections for
plug portions) of AS/NZS 3112 is covered by clause
23 of this standard
N/A
NOTE 2 Clause J.2.2.6.2 (High voltage test) of
AS/NZS 3112, except for the test of the insulation
of the insulated pins, is covered by clause 16 of this
standard.
N/A
NOTE 3 Clause J.2.2.6.4 (Temperature rise test)
of AS/NZS 3112 is covered by clause 11 of this
standard
N/A
NOTE 4 Clause J.2.2.6.7 (Equipment with integral
pins intended to be supported by the contacts of a
socket-outlet) of AS/NZS 3112 is covered by clause
22.3 of this standard
N/A
Page 4 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 2
National Difference of Australia (AU)
AS/NZS 60335.1:2002 corresponding to IEC 60335-1:2002; am1; am2
Clause
Requirement – Test
24.1
Before Note 1, insert the following variation.
NOTE 201 The relevant IEC standard may be
replaced with the relevant Australia/New Zealand
standard where applicable.
24.1.7
Add the following variation to the test specification:
In Australia, telecommunication interface circuitry
must comply with the Telecom Labelling Notice
issued under the Telecommunications Act instead
of IEC 62151.
Result
Verdict
—
No telecommunication
network operation.
NOTE 201 The Telecommunications Act is
administered by the Australian Communications
and Media Authority.
N/A
N/A
25.1
After the requirement insert the following variation.
Supply cords for single-phase portable appliances
intended for direct connection to the supply mains,
shall be fitted with an appropriate plug complying
with AS/NZS 3112.
Fixed/ Stationary appliance.
N/A
Table 11
Replace footnote a with the following variation:
a
These cords may only be used if their length does
not exceed 2 m between the point where the cord
or cord guard enters the appliance and the entry to
the plug. However, they cannot be used in class I
appliances.
Class I appliance,
And it shall be provided with
supply cord/ interconnection
cord exceeding 2m.
N/A
Note)
This national deviation was declared by IECEE Member NCB: SAI-Global,
Last modification: 2010-04-19
Page 1 of 4
IEC60335_2_40F – ATTACHMENT 3
ATTACHMENT TO TEST REPORT IEC 60335-2-40
Schematic wiring diagram/ Circuit diagram
Report No.: 236145
Page 2 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 3
Attachment: Schematic wiring diagram (Indoor unit)
1/3
Page 3 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 3
Attachment: PCB circuit diagram (Indoor unit)
2/3
Page 4 of 4
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 3
Attachment: PCB circuit diagram (Indoor unit)
3/3
Page 1 of 8
IEC60335_2_40F – ATTACHMENT 4
ATTACHMENT TO TEST REPORT IEC 60335-2-40
Photos of appliance
Report No.: 236145
Page 2 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
1/7
Page 3 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
2/7
Page 4 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
(Brushless DC type of fan motor, which has no auxiliary capacitors)
3/7
Page 5 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
4/7
(Reactor)
Page 6 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
(Top view of Main PCB, components mounted side)
(Bottom view of Main PCB, lead-free soldered side)
5/7
Page 7 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
(Top view of BLDC PCB, components mounted side)
(Bottom view of BLDC PCB, lead-free soldered side)
6/7
Page 8 of 8
Report No.: 236145
IEC60335_2_40F – ATTACHMENT 4
Attachment: Photos (Indoor unit)
7/7
(Drain pump, optional)
(Drain pump, optional)