Pride Mobility JAZZY 1113 ATS Owner`s manual

Owner’s Manual
Exeter, PA
St. Catharines, ON
1-800-800-8586
www.pridemobility.com
SAFETY
GUIDELINES
The symbols below are used throughout this owner's manual and on the power chair to identify warnings and
important information. It is very important for you to read them and understand them completely.
WARNING! Failure to follow designated procedures can cause either personal injury,
component damage, or malfunction (black symbol on yellow triangle with black border).
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause injury to personnel and/or damage to equipment (white
symbol on blue dot).
PROHIBITED! These actions are prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause injury to personnel
and/or damage to equipment (black symbol with red circle and red slash).
Copyright © 2006
Pride Mobility Products Corp.
INFMANU1801/Rev K/July 2006
www.pridemobility.com
Jazzy 1113 ATS
C O N T E N T S
I.
INTRODUCTION ................................................................................................................................. 4
II.
SAFETY ................................................................................................................................................. 6
III. YOUR POWER CHAIR .................................................................................................................... 14
IV.
DISASSEMBLY AND ASSEMBLY ............................................................................................. 19
V.
COMFORT ADJUSTMENTS........................................................................................................ 25
VI. BATTERIES AND CHARGING .................................................................................................... 31
VII. OPERATION ....................................................................................................................................... 35
VIII. CARE AND MAINTENANCE ........................................................................................................ 51
IX. WARRANTY ......................................................................................................................................... 56
This owner’s manual is compiled from the latest specifications and product information available at the time of publication.
We reserve the right to make changes as they become necessary. Any changes to our products may cause slight variations
between the illustrations and explanations in this manual and the product you have purchased.
Jazzy 1113 ATS
www.pridemobility.com
3
I.
INTRODUCTION
SAFETY
WELCOME to Pride Mobility Products Corporation (Pride). The power chair you have purchased combines state-ofthe-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you
with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for
your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the
first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for setup or
operation, please contact your authorized Pride Provider. Failure to follow the instructions in this manual and those
located on your power chair can lead to personal injury and/or damage to the power chair, including voiding the
warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or
render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any
retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety
and reliability of your new power chair, and about the service you received from your authorized Pride Provider.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to contact us
at the address below:
Pride Mobility Products Corporation
Attn: Customer Care Department
182 Susquehanna Avenue
Exeter, PA 18643-2694
customercare@pridemobility.com
800-424-8205
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
www.pridemobility.com
Jazzy 1113 ATS
I.
INTRODUCTION
PRIDE OWNERS CLUB
As an owner of a Pride product, you are invited to register your product’s warranty and enroll in the Pride Owners Club.
You may do so by filling out and returning your enclosed product registration card or by visiting Pride's web site at
www.pridemobility.com. As a registered member, each time you visit our site, you will have access to the most interactive
and honest educational venue available today for people with mobility needs, their families, and friends.
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You
will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive
message boards. These message boards invite you to communicate with other Pride customers as well as Pride representatives who are available to assist you with any questions or concerns you may have.
My Authorized Pride Provider:
Name:_____________________________________________________________________________________
Address:___________________________________________________________________________________
Phone Number:______________________________________________________________________________
Purchase Date:_______________________________________________________________________________
Jazzy 1113 ATS
www.pridemobility.com
5
I I .
S A F E T Y
SAFETY
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive
variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair
to the user and has assisted the prescribing healthcare professional and/or the authorized Pride Provider in the instruction
process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice operating
the power chair in the presence of a trained attendant. A trained attendant can be defined as a family member or care
professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you will need
some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,
on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help the user become accustomed to operating
the power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility. A wide range of accessories
is available from your authorized Pride Provider to further customize your power chair to better suit your needs and/or
preferences. However, under no circumstances should you modify, add, remove, or disable any feature, part, or function
of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Unauthorized
modifications may result in personal injury and/or damage to your power chair.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your power chair operates smoothly and safely. See VIII. “Care and Maintenance.”
Perform the following inspections prior to using your power chair:
! Check for proper tire inflation. Maintain 35 psi (2.4 bar) in each tire if equipped with pneumatic tires.
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all controller connections to the electronics tray. Make sure they are secured properly.
! Check the brakes. See VIII. “Care and Maintenance.”
! Check battery charge. See VI. “Batteries and Charging.”
NOTE: If you discover a problem, contact your authorized Pride Provider for assistance.
6
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
WARNING! Exceeding the weight capacity voids your warranty and may result in personal injury
and/or damage to your power chair. Pride will not be held responsible for injuries and/or property
damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may result in personal injury and/or property damage.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked at least once a
week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power
chair.
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at
all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control,
and overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic
tires at all times may result in tire and/or wheel failure, causing serious personal injury and/or
damage to your power chair.
WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure gauge. Inflating your tires from an unregulated air source could overinflate them, resulting
in a burst tire and/or personal injury.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s rear
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure a
safely controlled descent. See VII. “Operation.”
! Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate
cautiously. When driving down an incline, set your power chair to the slowest setting and drive in the forward direction
only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come to a
complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the incline.
Drive your power chair straight up the incline. This greatly reduces the possibility of a tip or a fall.
Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas covered
with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the power chair in freewheel
mode while seated on it or standing next to it. Doing so may result in personal injury and/or
damage to your power chair.
WARNING! Never travel down an incline backwards. This may result in personal injury.
Jazzy 1113 ATS
www.pridemobility.com
7
II.
SAFETY
In compliance with the Americans with Disabilities Act of 1990, all handicap public access ramps are required to have a
maximum slope of 5° (8.7%). Therefore, Pride recommends that the maximum slope of an incline you attempt to safely
ascend or descend on your power chair does not exceed 5° (8.7%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° (8.7%) may put your power
chair in an unstable position and cause it to tip, resulting in personal injury.
5 (8.7%)
Figure 1. Maximum Safe Angle (Ascending and Descending)
Braking Information
Your power chair is equipped with two powerful brake systems:
1. Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
2. Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when
power is removed from the system for any reason.
Cornering Information
While your power chair is equipped with rear caster wheels and front anti-tip wheels, excessively high cornering speeds
can still create the possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to:
cornering speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from an
area of low traction to an area of high traction (such as passing from a grassy area to a paved area – especially at high
speed while turning), and abrupt directional changes. High cornering speeds are not recommended. If you feel that you
may tip over in a corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your power
chair from tipping.
WARNING! When cornering sharply, reduce your speed. This greatly reduces the possibility of a
tip or fall. To avoid personal injury and/or property damage, always exercise common sense when
cornering.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed
of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encounter other surface
types. For this reason, your power chair is designed to perform admirably on packed soil, grass, and gravel. Feel free to
use your power chair safely on lawns and in park areas.
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can entangle the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
8
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Freewheel Mode
Your power chair is equipped with a manual freewheel lever to allow for manual maneuverability by a trained attendant.
For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present. Personal injury may result.
WARNING! Do not attempt to personally place your power chair in freewheel mode while seated
on it. Personal injury may result. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline. The chair could
roll uncontrollably on its own, causing personal injury.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches,
stairs, etc.). The correct method for approaching a curb is illustrated in figure 2.
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than two inches unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backwards down any step, curb, or
other obstacle. This may cause the power chair to tip and cause personal injury.
CURB
CURB
Figure 2. Correct Curb Approach
Figure 3. Incorrect Curb Approach
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with extreme caution.
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators. You may cause injury to
yourself and to others and/or damage your power chair.
Jazzy 1113 ATS
www.pridemobility.com
9
II.
SAFETY
Transfers
Transferring onto and off of your power chair requires a good
sense of balance. Always have an attendant or healthcare
professional present while learning to properly transfer
yourself.
To eliminate the possibility of injury, Pride recommends that
you or a trained attendant perform the following tasks before
attempting a transfer.
! Turn off the power to the controller. See VII. “Operation.”
! Ensure your power chair is not in freewheel mode. See
III. “Your Power Chair.”
! Turn both caster wheels toward the transfer destination
to improve power chair stability during transfer.
! Make sure both armrests are flipped up or removed from
your power chair.
! Flip the foot platform up, or move the leg rests aside; this
will help to keep your feet from getting caught on the foot
riggings during the transfer.
! Reduce the distance between your power chair and the
object you are transferring onto.
Figure 4. Ideal Transfer Position
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer and causing injury.
WARNING! Avoid using your armrests for weight bearing purposes. Such use may cause the power
chair to tip and cause personal injury.
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power
chair to tip and cause personal injury.
Doors
! Determine if the door opens toward or away from you.
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly
backwards to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the power chair and the door will reopen.
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
10
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in transportation.
Pride recommends that you closely review the instructions, specifications, and safety information set forth by the manufacturer
of the lift/elevation product before using that product.
WARNING! Never sit on your power chair when it is being used in connection with any type of lift/
elevation product. Your power chair was not designed with such use in mind and any damage or
injury incurred from such use is not the responsibility of Pride.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair
should be stowed in a trunk of a car or in the back of a truck or van with the batteries removed and properly secured.
WARNING! Do not sit on your power chair while it is in a moving vehicle. Personal injury and/or
property damage may result.
WARNING! Always be sure your power chair and its batteries are properly secured when it is being
transported. Failure to do so may result in personal injury and/or damage to your power chair.
Positioning Belts
Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely. Serious personal injury may result if you fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be
properly belted into seats approved by the vehicle manufacturer.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly caught
up in rain, snow, severe cold, or heat while operating your power chair proceed to shelter at the earliest opportunity.
Thoroughly dry your power chair before storing, charging, or operating your power chair
WARNING! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces can
cause personal injury and/or damage to the power chair and electrical system. Maintain and
store your power chair in a dry and clean condition.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while seated
on your power chair, it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride
recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the
presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the floor by reaching
down between your knees. Movements such as these may change your center of gravity and the weight
distribution of the power chair. This may cause your power chair to tip, possibly resulting in personal injury.
WARNING! Prevent personal injury! Keep your hands away from the tires when driving. Be aware that loose
fitting clothing can become caught in drive tires.
Jazzy 1113 ATS
www.pridemobility.com
11
II.
SAFETY
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For more
information about your power chair’s batteries, see VI. “Batteries and Charging.”
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that much
weight, be sure to get help. Lifting beyond your capacity can result in personal injury.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING! Always protect the batteries from freezing and never charge a frozen battery. Charging a frozen
battery may result in personal injury and/or damage to the battery.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time, turn off
the power. This will prevent unexpected motion from inadvertent joystick contact. This will also eliminate
the possibility of unintended chair movement from electromagnetic (EMI) sources. Failure to do so may
result in personal injury.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when
taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or if you
have certain physical limitations. Some medications and limitations may impair your ability to operate your
power chair in a safe manner.
Alcohol
The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness
of safety issues while under the influence of alcohol.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this may impair
your ability to operate your power chair in a safe manner.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts. Personal injury and/
or damage to the power chair may result.
12
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way
radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,
microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency vehicles. In some
cases, these waves can cause unintended movement or damage to the control system. Every electrically-powered mobility
vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the greater the protection against EMI. This
product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio transmitters
may cause unintended movement of your electrically-powered mobility vehicle due to EMI.
Exercise caution when using any of these items while operating your mobility vehicle and avoid
coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way
not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, visit the Resource Center on www.pridemobility.com. If unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call Pride at 800424-8205 to report the incident.
Jazzy 1113 ATS
www.pridemobility.com
13
III.
YOUR
POWER
CHAIR
THE JAZZY 1113 ATS
Your power chair has two main assemblies: the seat and the power base. See figure 5. Typically, the seating system
includes the armrests, the seatback, the seat base, and the joystick/controller. The power base assembly includes two
drive wheels, two anti-tip wheels, two rear caster wheels, a body shroud, four frame assemblies (located under the body
shroud), two battery boxes, and the electrical connectors. See figures 5, 6, and 7.
SEAT BACK
ARMRESTS
SEAT
ASSEMBLY
CONTROLLER
SEAT BASE
BODY SHROUD
FREEWHEEL LEVERS
POWER
BASE
ASSEMBLY
CASTER WHEEL
FOOT RIGGING
(FOOT PLATFORM SHOWN)
DRIVE WHEEL
ANTI-TIP WHEELS
Figure 5. The Jazzy 1113 ATS
14
www.pridemobility.com
Jazzy 1113 ATS
III.
YOUR
POWER
CHAIR
Specifications
Suspension:
Drive Wheels:
Caster Wheels:
Anti-Tip Wheels:
Maximum Speed:¹
Brakes:
Ground Clearance:²
Turning Radius:²
Overall Size:²
Seating Options:
Drivetrain:
Batteries:³
Range:¹
Battery Charger:
Electronics:
Weight Capacity:
Component Weights:
Active-Trac Suspension
10 in., pneumatic, center-mounted (solid tires are optional)
8 in., solid, rear articulating
6 in., solid, front mounted
Up to 4 mph
“Intelligent Braking,” electronic regenerative, disc park brake
2.5 in.
18.5 in.
Length: 36.5 in.
Width: 23 in. (assembled)
Medium-back (standard)
Specialty Seat
High-back with Headrest
Synergy Seat
Synergy Manual Tilt
Synergy TRU-Balance Power Positioning Systems
Two motor, mid-wheel
Two 12-volt, U-1 batteries
Up to 25 miles
3-amp, Onboard (standard)
3-amp, Off-board
50-amp PG VSI Controller
70-amp Europa Remote Controller
70-amp PG Remote Plus Controller
70-amp PG Microdrive Controller
300 lbs. (160 lbs. with Synergy Manual Tilt)
Seat: 33 lbs.
Foot Platform: 8.5 lbs.
Front Battery and Case: 26 lbs. (U-1 Battery: 24.5 lbs.)
Rear Battery and Case: 26 lbs. (U-1 Battery: 24.5 lbs.)
Battery Well Frame: 13.5 lbs.
Front Frame: 2.5 lbs.
Right Frame Assembly: 38 lbs.
Left Frame Assembly: 38 lbs.
¹Varies with user weight, terrain type, battery amp hour rating (AH), battery charge, battery condition, and tire condition.
²Due to manufacturing tolerances and continued product improvement, this specification can be subject to variance of
(+ or – ) 3%.
³AGM or Gel-Cell type recommended.
NOTE: All specifications subject to change without notice.
Jazzy 1113 ATS
www.pridemobility.com
15
III.
YOUR
POWER
CHAIR
Electrical Components
The electrical components consist of the controller, the batteries, and the motors. The batteries, motors, and controller
power module (if equipped) are located on the power base assembly. The controller is located on the seat assembly.
Connectivity between the controller and the motors, batteries, and the battery charger is provided by one or more wiring
harnesses. See figures 6 and 7.
Controller Connector: This is where the controller harness connects to the power base.
Ammeter: This displays the charger’s current output in amps.
Main Circuit Breaker: This is a safety feature built into your power chair. When the batteries and the motors are heavily
strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If
the circuit trips, allow the power chair to “rest” for approximately one minute. Then, push in the circuit breaker button, turn
on the controller, and continue normal operation. If the main circuit breaker continues to trip repeatedly, contact your
authorized Pride Provider.
Charger Power Cord Receptacle: This is where the charger power cord plugs in when the batteries need to be recharged.
Battery Connectors (Quick-Connectors): These provide a connection between the battery boxes and the electronics
tray.
Motor Connectors: These provide a connection between the motors and the electronics tray.
AMMETER
CONTROLLER CONNECTOR
(VSI SHOWN)
MAIN CIRCUIT BREAKER
CHARGER POWER CORD
RECEPTACLE
Figure 6. Power Base Rear View - Electronics Tray
16
www.pridemobility.com
Jazzy 1113 ATS
III.
YOUR
BATTERY CONNECTORS
(QUICK-CONNECTORS)
POWER
CHAIR
REAR BATTERY BOX
MOTOR CONNECTOR
SEAT TOWERS
MOTOR CONNECTOR
FRONT
BATTERY
BOX
Figure 7. Power Base Top View
Manual Freewheel Levers
For convenience, your power chair is equipped with two manual freewheel levers—one for each motor. See figures 8 and
9. These levers allow you to disengage the drive motors from the gearboxes and maneuver the chair manually. This is called
freewheel mode.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage
the drive motors when the power chair is on an incline, as the unit could roll on its own, causing
injury!
WARNING! In freewheel mode, the braking system is disengaged. Only engage the freewheel
mode when on a level surface. Failure to comply could result in injury and/or damage to your
product.
Jazzy 1113 ATS
www.pridemobility.com
17
III.
YOUR
POWER
MANUAL
FREEWHEEL
LEVER
MANUAL
FREEWHEEL
LEVER
Figure 8. Drive Mode (Drive Engaged)
CHAIR
Figure 9. Freewheel Mode (Drive Disengaged)
To engage or disengage the drive motors:
1. Locate the manual freewheel levers at the front of the chair. See figure 5.
2. Push the levers down to engage the drive motors. See figure 8.
3. Pull the levers upward to disengage the drive motors. See figure 9.
NOTE: If a lever is difficult to move in either direction, rock your power chair back and forth slightly. The
lever should then move to the desired position.
Active-Trac System
Your power chair is equipped with an Active-Trac System (ATS). See figure 10. ATS is a suspension system designed to
make your power chair traverse different types of terrain and obstacles while maintaining smooth operation. With ATS,
your front anti-tip wheels work in conjunction with your motor suspension to help you maneuver over obstacles.
As the front anti-tip wheels come in contact with an obstacle, the front anti-tip wheel assembly is drawn upward. At the
same time, the motors are forced downward. This allows the motors to push the power chair over an obstacle and limits
the possibility of your power chair becoming “hung up” on the obstacle.
ATS also helps in day-to-day operating conditions. For instance, when you release the joystick, your power chair begins
to slow down. As the chair slows down, the front anti-tip wheels will automatically drop toward the ground. This will
reduce the forward tip that is typically encountered with center-wheel drive chairs.
ATS SPRING
Figure 10. ATS System
18
www.pridemobility.com
Jazzy 1113 ATS
I V. D I S A S S E M B LY A N D A S S E M B LY
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly
to make some comfort adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores
or through your authorized Pride Provider..
Seat Installation
It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are
attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be
attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main components are
aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the
power base.
WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose
control of the seat if they do so, resulting in personal injury or damage to the chair.
To install the seat:
1. Set the trapeze bars to the desired . To change the trapeze bar height, see V. “Comfort Adjustments.”
2. Tilt the seat back, and slide the rear extrusion onto the rear trapeze bar. See figure 11.
3. Lower the front extrusion onto the front trapeze bar until the seat locks into place.
4. Flip the seat latch safety down. See figure 12.
WARNING! Make sure the seat latch safety is flipped down before using your power chair.
5. Install the controller into one of the armrests. See V. “Comfort Adjustments.”
6. Route the controller cable so that it cannot be pinched in the seat hinge and plug the cable into the controller connector
on the electronics tray.
7. Secure the controller cable to the armrest receiver with one or more wire ties.
SEAT LATCH SAFETY
REAR
TRAPEZE BAR
REAR EXTRUSION
FRONT TRAPEZE BAR FRONT EXTRUSION
Figure 11. Universal Mounting System
Jazzy 1113 ATS
Figure 12. Seat Latch Safety
www.pridemobility.com
19
I V. D I S A S S E M B L Y A N D A S S E M B LY
DISASSEMBLY
Your power chair disassembles into eight easily transportable component assemblies with no tools required. See figures 13
and 14. Place the power chair in an area where there is ample space to work and move around the unit—three or more
feet of clearance on all sides. Make sure the unit is powered off before disassembling the chair.
WARNING! Even though no tools are required to disassemble or assemble your power chair, you
should take care not to place your hands or fingers on the areas of the component assemblies
where they may be pinched, as the assemblies “snap” together or “snap” apart.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
NOTE: During both the disassembly and the assembly of your power chair, you may find it helpful to engage
the drive motors to secure the unit from rolling. See III. “Your Power Chair.”
LEFT POWER BASE
FRAME ASSEMBLY
BATTERY WELL
FRAME
FRONT FRAME
BATTERY BOXES
RIGHT POWER BASE
FRAME ASSEMBLY
FOOT PLATFORM
Figure 13. Jazzy 1113 ATS Component Assemblies
20
www.pridemobility.com
Jazzy 1113 ATS
I V. D I S A S S E M B LY A N D A S S E M B LY
BALL DETENT
PIN
SEAT TOWER
Figure 14. Seat Installation/Removal
Jazzy 1113 ATS
www.pridemobility.com
21
I V. D I S A S S E M B L Y A N D A S S E M B LY
To disassemble your power chair:
1. Disconnect the controller harness from its connector on the
electronics tray. See figure 6. You may need to pull firmly and
gently wiggle the harness to remove it from the connector.
2. Remove the ball detent pin from each seat tower. See figure 14.
3. Pull up on the seat. You may find it necessary to wiggle the
frame gently from side to side to free it from the seat towers.
WARNING! Do not pick up the seat frame by the
armrests. They are free to pivot, and you may lose
control of the seat if they do so, resulting in
personal injury and/or damage to the chair.
4. Remove the foot platform by lifting it up, then pulling it out away
from the chair. See figure 15.
5. Disconnect both battery connectors and both motor connectors.
See figure 7.
6. Lift and remove each battery box. See figure 16.
7. Squeeze together the latch release levers that hang vertically
down from the crossbar at the rear of the battery well frame.
See figure 17.
8. Lift up the rear end of the battery well frame. Pull it to the rear
of the chair to release the front slots from the locating pins on
the front frame bottom bar.
9. Stand behind your power chair and grasp one of the power
base frame assembly handles. See figure 18.
10. Press the chrome latch release lever toward the center of the
frame and hold it.
11. Push the frame assembly outward and pull up on the front frame
until the latching mechanism releases.
12. Keep pulling upward until the locating pin on the bottom of the
front frame releases from its slot in the power base frame
assembly.
13. Carefully let the power base frame assembly tilt to a resting
position.
14. Repeat steps 9-13 for the other power base frame assembly.
22
www.pridemobility.com
Figure 15. Foot Platform Removal
Figure 16. Removing Battery Boxes
Jazzy 1113 ATS
I V. D I S A S S E M B L Y A N D A S S E M B L Y
ASSEMBLY
To assemble the power chair:
1. Place the three frame assemblies next to each other as shown in
figure 19.
2. Grasp the front frame and fit the notch on the front frame bottom
bar onto the locating pin on the lower section of the power base
frame assembly. See figure 20.
WARNING! The front frame should be positioned
with the two semicircular notches in the vertical
bar facing forward.
3. Pivot the front frame top bar toward the power base frame
assembly and push the front frame top bar onto the locking
mechanism until the two assemblies snap securely into place.
See figure 18.
4. Repeat steps 1-3 for the other power base frame assembly.
WARNING! Make certain that the front frame is
snapped securely to both the right frame
assembly and to the left frame assembly.
5. Hold the battery well frame so that the bottom of the well hangs
downward.
6. Position the notches on the front of the battery well frame onto
the locating pins on the front frame bottom bar. See figure 20.
7. Fit the notch on either side of the rear of the battery well frame
onto the locating pin on each power base frame assembly.
8. Make certain that the locking mechanisms snap securely into
place.
9. Place the front battery box into the front end of the battery well
frame.
Figure 17. Removing Battery Well Frame
NOTE: Make certain that the connectors are facing toward
the center of the power chair.
10. Place the rear battery box into the back end of the battery well
frame. Make certain that none of the wiring harnesses or cables
are pinched between the battery or the motor controller box
and the frame.
11. Connect the battery boxes. Use the battery connection label
located on the back of the electronics tray for reference.
12. Reconnect the left and right motor connectors. Be certain to
match the left connector to the left motor and the right connector
to the right motor. The connectors are labeled left and right.
Figure 18. Power Base Frame Removal/
Installation
Jazzy 1113 ATS
www.pridemobility.com
23
I V. D I S A S S E M B L Y A N D A S S E M B LY
13. Pick up the seat by the frame and set the seat onto the towers
so the holes align with those on the seat towers.
14. Insert the ball detent pin into each seat tower.
15. Match the two tabs at the back of the foot platform mounting
bracket with the two semicircular notches in the vertical bar of
the front frame.
16. Push the tabs through the matching notches.
17. Slide the foot platform down into place.
18. Reconnect the controller harness to its connector on the
electronics tray. See figure 6.
WARNING! Do not place the controller harness
so that it can be pinched in the seat frame or
the power base frame.
Figure 19. Frame Assembly Position
LOCATING PINS
BATTERY WELL FRAME
Figure 20. Connect Battery Well Frame
24
www.pridemobility.com
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. If your
power chair is equipped with a Synergy Seating System or Synergy TRU-Balance Power Positioning System, refer to the
information in separate manuals. If your power chair is equipped with a contour seating system, refer to the following
information.
WARNING! If your power chair was configured by your authorized Pride Provider, please consult your
healthcare professional before making any adjustment that may degrade your power chair’s
performance and safety by changing its center of gravity.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
WARNING! Prevent injury. Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort adjustments:
! metric/standard socket set and ratchet
! adjustable wrench
! metric/standard hex key set
! thread lock
BALL DETENT PIN
Seat Height and Seat Angle Adjustment
You can change the seat height by either raising or lowering the four seat towers.
To change the seat height:
1. Turn off the power to the controller.
2. Disconnect the controller harness connector from the electronics tray.
3. Remove the ball detent pins that attach the trapeze bars to the seat towers. See
figure 14.
4. Remove the seat.
5. Remove the battery harnesses.
6. Remove the battery boxes.
7. Remove the ball detent pin from each seat tower as shown in figure 21.
8. Raise or lower each seat tower to the desired position.
9. Install the ball detent pin into each seat tower.
10. Reinstall the battery boxes.
11. Reinstall the battery harnesses.
12. Reinstall the seat and secure the trapeze bars.
13. Connect the controller harness connector to the electronics tray
Figure 21. Seat Tower
To change the seat angle:
Raise or lower only one set of seat towers (front or rear).
Jazzy 1113 ATS
www.pridemobility.com
25
V.
COMFORT
ADJUSTMENTS
Seat Position
You can move the seat forward or rearward by changing the extrusion mounting position.
To
1.
2.
3.
4.
5.
change the position:
Turn off the power to the controller.
Disconnect the controller from the electronics tray.
Remove the seat from the power base.
Remove both extrusions from the bottom of the seat.
Reposition the extrusions on a different set of mounting holes.
You must move both extrusions the same number of holes either
forward or backward. See figure 22.
6. Fasten the extrusions back onto the bottom of the seat.
7. Reinstall the seat.
8. Connect the controller to the electronics tray.
Manual Recline Seatback Adjustment
If your power chair is equipped with an optional reclining seat, you
can adjust the seatback angle with the seatback release lever. The
lever is located on the right side of the seat base.
To adjust the seatback angle:
1. Pull up on the seatback release lever.
2. Move the seatback down or up to the desired position.
3. Release the lever.
Headrest Adjustment
If your power chair is equipped with the optional high-back seat
with headrest, you can adjust the headrest height.
To adjust the headrest height:
1. Push in the headrest release button.
2. Move the headrest up or down to the desired position.
Seatback Angle Adjustment
If your power chair is equipped with an adjustable seatback, you
can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.
To adjust the seatback angle:
1. Remove the seatback angle adjustment screws from both seat
hinges. See figure 23.
2. Set the seatback at the desired angle.
3. Reinstall the screws to both seat hinges and tighten.
Figure 22. Seat Mounting Holes
ARMREST
ANGLE
ADJUSTMENT
SCREW
JAM NUT
ARMREST
HEIGHT
ADJUSTING
SETSCREWS
SEATBACK
ANGLE
ADJUSTMENT
SCREW
ARMREST KNOB
Figure 23. Seatback and Armrest Adjustments
Armrest Width Adjustment
You can change each armrest’s width independently of the other.
26
www.pridemobility.com
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
NOTE: Changing the armrest width may increase the overall
width of your power chair.
To change the armrest width:
1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 23.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Height Adjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest receiver. See
figure 23.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
SETSCREW
Figure 24. Underside of Armrest
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to the floor.
2. Loosen the jam nut. See figure 23.
3. Turn the adjustment screw clockwise to raise the front of the armrest, or turn the adjustment screw counterclockwise to lower the
front of the armrest.
5. Tighten the jam nut to lock the adjustment screw into place.
FOOT PLATFORM BRACKET
Controller Position
You can position the controller for either left-hand or right-hand use.
To change the controller position:
Figure 25. Foot Platform Height Adjustment
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the power base.
3. Cut any wire ties that attach the controller cable to the armrest.
4. Flip up the armrest and loosen the setscrew. See figure 24.
5. Slide the controller out of the armrest and place it in the other
armrest.
6. Tighten the setscrew.
7. Use a wire tie to secure the controller harness to the armrest.
8. Plug the controller connector(s) into the power base.
Foot Platform Height Adjustment
The foot platform height is easily adjusted to different heights in 1/
2-in. increments.
SETSCREW
To raise or lower the foot platform:
1. Remove the hardware from the foot platform bracket. See figure 25.
Figure 26. Foot Platform Angle Adjustment
2. Raise or lower the foot platform to the desired height.
3. Reinstall the hardware into the foot platform bracket and tighten.
Jazzy 1113 ATS
www.pridemobility.com
27
V.
COMFORT
ADJUSTMENTS
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with a hex key and
wrench.
To adjust the foot platform angle:
1. Flip up the foot platform and locate the setscrew. See figure 26.
2. Loosen the nut and turn the setscrew counterclockwise
to raise the front of the foot platform or clockwise to
lower the front of the foot platform
3. Tighten the nut to secure the setscrew.
Swing-Away Footrests
Swing-Away Footrests (SFRs) enable you to rotate the footrests to the side before you transfer onto or off of your power
chair. See figure 27.
SFR RELEASE LEVER
FOOTREST
EXTENSION
ADJUSTMENT
SCREWS
Figure 27. Swing-away Footrest Adjustment
To rotate the SFRs:
1. Push in the release lever.
2. Rotate the SFRs.
RELEASE LEVER A
RELEASE LEVER B
To adjust the SFR length:
1. Remove the two adjustment screws from the back of
each footrest extension.
2. Slide the footrest up or down to the desired length.
3. Reinstall the two adjustment screws.
Elevating Leg Rests
Elevating Leg Rests (ELRs) offer an infinite range of adjustment for the leg angle and a footrest adjustment range of 12–
19 in. See figure 28.
To rotate the ELRs:
1. Push in release lever A.
2. Rotate the ELRs.
LEG REST
EXTENSION
ADJUSTMENT
SCREWS
Figure 28. Elevating Leg Rests
LEG REST
HANGER
ADJUSTMENT BOLT
To adjust the ELR angle:
1. Push down release lever B.
2. Move the leg rest to the desired angle.
LEG REST
EXTENSION
ADJUSTMENT SCREWS
To adjust the ELR length:
1. Remove the two adjustment screws from the side of each
leg rest extension.
2. Slide the leg rest up or down to the desired length.
3. Reinstall the two adjustment screws.
Figure 29. Heavy Duty Drop-In Leg Rests
28
www.pridemobility.com
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
Heavy Duty Drop-in Leg Rests (Optional)
You can adjust the forward/back position, as well as the
length of the heavy duty drop-in leg rests. See figure 29.
To adjust the forward/back position:
1. Remove the adjustment bolt from each side rail.
2. Move the leg rest hanger in or out to the desired position.
3. Align the adjustment holes in the leg rest hanger with
those in the side rail.
4. Reinstall each adjustment bolt to secure the leg rest
hangers.
A
B
C
To adjust the leg rest length:
1. Remove the adjustment screws from the leg rest
extension.
2. Slide the leg rest up or down to the desired length.
3. Align the adjustment holes in the leg rest extension
and reinstall the adjustment screws.
Multi-Axis Foot Plates
The multi-axis foot plate assembly can be installed on either
a swing-away footrest or an elevating leg rest. The multiaxis foot plate has four adjustments: leg rest length (A),
position (B), tilt (C), and angle (D). See figure 30.
D
A
B
To change leg rest length (A):
1. Remove the hardware.
2. Move the leg rest to the desired position.
3. Reinstall the hardware.
To change foot plate position (B):
1. Remove the hardware.
2. Move the foot plate to the desired position.
3. Reinstall the hardware.
C
To change foot plate tilt (C):
1. Loosen the hardware.
2. Tilt the foot plate to the desired position.
3. Tighten the hardware.
D
To change foot plate angle (D):
1. Turn the setscrew clockwise to decrease the angle.
2. Turn the setscrew counterclockwise to increase the
angle.
Jazzy 1113 ATS
SETSCREW
LOCATION
Figure 30. Multi-Axis Foot Plate
www.pridemobility.com
29
V.
COMFORT
ADJUSTMENTS
Anti-Tip Wheel Adjustment
The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are
preset for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may be
necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need adjustment if either of the
following occur:
! When coming to a stop, your power chair tips forward excessively.
! The anti-tip wheels constantly rub the ground.
NOTE: Each drive tire must have at least 35 psi (2.4 bar) of air pressure in order for the anti-tip wheels to be
properly adjusted.
To adjust the anti-tips:
1. Make sure the power chair is in drive mode.
2. Loosen the nut and bolt that fasten the anti-tip spring to the anti-tip arm. See figure 31.
3. Remove the anti-tip adjustment bolt.
4. Raise or lower the anti-tip wheel in 1/4-in. increments.
5. Replace the hardware into the appropriate hole and tighten.
WARNING! Consult your authorized Pride Provider before attempting to change the anti-tip height!
Changing the anti-tip wheel height affects handling under deceleration!
WARNING! The higher you raise the anti-tip wheels, the more tendency your power chair has to tilt forward
when coming to a stop. You can compensate for this by making a small adjustment to the pre-programmed
deceleration setting in the controller or by moving the seat assembly farther to the rear of your power chair.
Failure to do so may result in personal injury.
PROHIBITED! Do not remove the anti-tip wheels.
NUT AND BOLT
ANTI-TIP ADJUSTMENT BOLT
ANTI-TIP WHEEL
Figure 31. Anti-Tip Adjustment
30
www.pridemobility.com
Jazzy 1113 ATS
VI.
BATTERIES
AND
CHARGING
BATTERIES AND CHARGING
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a
longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING! Prevent injury and/or equipment damage! Do not use batteries that exceed the
recommended type and amp-hour capacity. Do not use batteries with different amp-hour capacities.
Refer to specifications table in this manual and in the manual suppled with the battery charger
for recommended type and capacities.
Charging the Batteries
The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power
chair’s performance by charging the batteries safely, quickly, and easily. The battery charging system consists of the battery
charger, the charger circuit fuse, and the ammeter (onboard chargers only). The ammeter indicates the rate of charge
necessary to fully recharge the batteries. It is also a good indication of whether or not the charger is working. The ammeter
and the charger are only functional when the charger power cord is plugged into an electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Failure
to heed could result in personal injury and/or property damage.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger
directly into a properly wired standard electrical outlet.
WARNING! You must recharge your power chair’s batteries with the supplied onboard charger. Do
not use an automotive-type battery charger.
WARNING! Prevent injury and/or equipment damage! Read the battery charging instructions in
this manual and in the manual supplied with the battery charger before charging the batteries.
WARNING! Prevent injury and/or equipment damage! Do not expose the off-board battery charger
to rain or other sources of moisture unless it has been tested for outdoor use. Refer to the manual
supplied with the battery charger for more information.
WARNING! Prevent injury and/or equipment damage! Explosive gases may be generated while
charging the batteries. Keep the power chair and battery charger away from sources of ignition
such as flames or sparks and provide adequate ventilation when charging the batteries.
WARNING! Prevent injury and/or equipment damage! Inspect the battery charger, wiring, and
connectors for damage before each use. Contact your authorized Pride Provider if damage is
found.
WARNING! Prevent injury and/or equipment damage! Do not attempt to open the battery charger
case. If the battery charger does not appear to be working correctly, contact your authorized
Pride Provider.
WARNING! Prevent injury and/or equipment damage! If the off-board battery charger is equipped
with cooling slots, then do not attempt to insert objects through these slots.
WARNING! Prevent injury and/or equipment damage! Do not allow unsupervised children to play
near the power chair while the batteries are charging.
Jazzy 1113 ATS
www.pridemobility.com
31
VI.
BATTERIES
AND
CHARGING
WARNING! Prevent injury and/or equipment damage! If your off-board battery charger has not
been tested and approved for outdoor use, then do not expose it to adverse or extreme weather
conditions. If the battery charger is exposed to adverse or extreme weather conditions, then it
must be allowed to adjust to the difference in environmental conditions before use indoors. Refer
to the manual supplied with the battery charger for more information.
To charge the batteries using the onboard charger:
1. Position the rear of your power chair close to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power
Chair.”
3. Plug the charger power cord into the charger power cord receptacle on the power base, then into the electrical outlet.
NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is
plugged into an electrical outlet.
4. We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly drops to 0.
NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. As the batteries
charge, the ammeter needle slowly drops to 0. When the batteries are fully charged, the needle vibrates on or
about the 0 mark on the ammeter.
5. When your power chair’s batteries are fully charged, disconnect the charger power cord, wind up the cord, and store
it in a safe place.
To charge the batteries using the optional off-board charger:
1. Position the front of your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power
Chair.”
3. Plug the off-board charger into the off-board charger/programming socket on the controller. See VII. “Operation.”
4. Plug the off-board charger into the electrical outlet.
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to
the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride offboard charger, then follow the instructions supplied by the manufacturer.
5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.
Battery Break-in
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance
level.
2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you
become accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now
perform at over 90% of their potential.
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.
32
www.pridemobility.com
Jazzy 1113 ATS
VI.
BATTERIES
AND
CHARGING
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it to 24
VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is
low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the charger doesn’t
work as hard to complete the charging cycle. When the battery is fully charged, the amperage from the charger is nearly at
zero. This is how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do
not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your authorized Pride Provider for assistance.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a
daily basis or you may not use it for weeks at a time.
! Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair.
Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the
batteries 8 to 14 hours after daily use.
! Infrequent Use
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per week
for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the
batteries for more than 24 hours at a charging cycle.
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More often you
are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind. All of these factors will
affect the distance or running time per battery charge. Below are a few suggestions for obtaining the maximum range per
charge:
! Always charge the batteries fully prior to your trip.
! Plan your trip in advance to avoid inclines if possible.
! Limit baggage weight to essential items.
! Try to maintain an even speed and avoid stop-and-go driving.
What type of batteries should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-cycle
batteries that are similar in performance.
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries to
reduce the risk of leakage or explosive conditions.
Jazzy 1113 ATS
www.pridemobility.com
33
VI.
BATTERIES
AND
CHARGING
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads),
or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain down their
charge, and then accept a relatively quick recharge. AGM and Gel-Cell batteries should be charged as often as possible.
They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific demands.
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encounter
temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the
power available and extends the time needed to recharge the battery (just as with a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More
importantly, it will take a few “charging cycles” (a partial drain— then a full recharge) to establish the critical chemical
balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in
your battery properly.
How can I ensure maximum battery life?
A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or
stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery
life.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least
once per week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect
the battery harnesses and store the power chair in a warm, dry environment. Avoid temperature extremes, such as freezing
and excessively hot conditions, and never attempt to charge a frozen battery. A cold or frozen battery should be warmed
for several days prior to recharging.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are
Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no
danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s
specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the
original shipping container and ship the batteries in separate boxes.
34
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
VSI CONTROLLER
The electronic controller is what you use to operate your power chair. The electronic controller enables you to move the
power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system.
The VSI electronic controller is an integral electronic controller. All of the electronics necessary to operate the power chair
are contained in one module. See figure 32. Typically, the VSI is mounted to one of the armrests and is connected to the
motors, batteries, and the onboard charger at the power base. The VSI may be used to control some optional systems
such as power elevating seats and lights.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If
it is programmed incorrectly or outside of the safe limits as determined by your healthcare professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized
representative of the manufacturer, or a trained service technician should program the controller.
The VSI consists of:
1. joystick
2. keypad
3. off-board charger/programming socket
4. actuator connector (optional)
5. controller connector
6. 3-pin charger inhibit connector
Joystick
The joystick controls the direction and speed of
your power chair. When you move the joystick
from the neutral (center) position, the
electromagnetic brakes release and allow your
power chair to move. The farther you push the
joystick from its neutral position, the faster your
power chair moves. When you release the joystick
and allow it to return to the neutral position, you
engage the electromagnetic brakes. This causes
your power chair to decelerate and come to a Figure 32. VSI Controller
complete stop.
WARNING! If your power chair
begins to move in an unexpected manner, immediately release the joystick. Unless the joystick is
damaged, this action should stop your power chair.
Keypad
The keypad is located in front of the joystick. It contains keys necessary to operate your power chair. See figure 33.
Jazzy 1113 ATS
www.pridemobility.com
35
VII.
OPERATION
On/Off Key
The on/off key turns the VSI on and off.
WARNING! Unless faced with an emergency situation, do not use the on/off key to stop the chair.
This will cause the power chair to stop abruptly.
WARNING! Always turn the power off when you are
stationary to prevent unexpected movement.
Battery Condition Meter
The battery condition meter is located in front of the joystick. See
figure 33. This is a 10-segment illuminated display that indicates that
the VSI is turned on and also gives the battery status, the VSI status,
and the electrical system status.
! Red, yellow, and green lights lit: Batteries charged; VSI and
electrical system OK.
! Red and yellow lights lit: Charge batteries if possible; VSI
and electrical system OK.
! Red lights only lit or slow flash: Charge batteries as soon as
possible; VSI and electrical system OK.
NOTE: When the batteries approach a discharged state, the
first red light will begin to slowly flash, reminding you the
batteries need to be charged immediately!
Figure 33. VSI Controller Keypad
! Rapid flash of lights: Indicates a fault in the VSI or the electrical
system. Refer to “VSI Error Codes.”
! Ripple side to side of lights: The joystick was not in the neutral position when the controller was turned on. If you
get “ripple side to side of lights,” turn off the controller, allow the joystick to return to the neutral position, then turn on
the controller.
NOTE: If you still get “ripple side to side of lights,” contact your authorized Pride Provider.
Speed/Profile Keys
There are two keys that control either the speed or the profile. See figure 33. This depends on how your VSI was
programmed. Press the speed/profile increase key to increase the speed or change the profile. Press the speed/
profile decrease key to decrease the speed or change the profile. The speed/profile setting is displayed on the
maximum speed/profile indicator. If your power chair was programmed with a drive profile, contact your authorized
Pride Provider for more information.
NOTE: We recommend that the first few times you operate your power chair, you set the speed to the
slowest setting until you become familiar with your new power chair.
36
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
Actuator Key and Actuator Lights (For Optional Equipment)
Actuator keys and actuator lights are used for optional equipment such as power elevating seats or power elevating leg
rests. For specific operation of the actuator keys and actuator lights, contact your authorized Pride Provider.
Horn Key
The horn key activates the horn.
Locking/Unlocking the VSI
The VSI has a feature that enables you to lock your power chair to prevent unauthorized use.
To lock the VSI:
1. With the VSI switched on, press and hold the on/off key. After one second, the VSI should beep.
2. Release the on/off key.
3. Push the joystick to the full forward position until the VSI beeps.
4. Pull the joystick to the full rearward position until the VSI beeps.
5. Release the joystick. There should be a long beep.
6. The VSI is now locked.
To unlock the VSI:
1. Press the on/off key and power on the VSI. The maximum speed/profile indicator should ripple side to side.
2. Push the joystick to the full forward position until the VSI beeps.
3. Pull the joystick to the full rearward position until the VSI beeps.
4. Release the joystick. There should be a long beep.
5. The VSI is now unlocked.
NOTE: If the above procedure fails to either lock or unlock the VSI, contact your authorized Pride Provider.
Off-board Charger/Programming Socket
You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front of the
VSI. See figure 32. If you use an off-board charger, the charger current should not exceed 8 amps. Contact your authorized
Pride Provider for more information.
WARNING! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/
programming socket. See your authorized Pride Provider for more information.
NOTE: The socket may also be used for reprogramming the VSI. Contact your authorized Pride Provider for
more information.
NOTE: Changes to the programming can only be made by the manufacturer, an authorized representative of
the manufacturer, or an authorized Pride Provider.
Controller Connector
This connects the VSI to the power chair’s batteries, motors, and motor brakes.
Jazzy 1113 ATS
www.pridemobility.com
37
VII.
OPERATION
3-pin Charger Inhibit Connector
This connects the VSI to the onboard battery charger. This connection provides an inhibit that disables the VSI when the
battery charger is on. The charger inhibit connector is coded with colored dots. The dots are positioned so that you align
the flat side of the male connector with the flat side of the female connector before making the connection.
WARNING! Failure to properly align the connectors can result in damage to the VSI, the charger,
and the connectors.
Thermal Rollback
The VSI controller is equipped with a thermal rollback circuit. The circuit monitors the temperature of the controller, which
roughly translates to motor temperature. In the event that the VSI controller becomes excessively hot (above 140° F),
motor current (amperage) is reduced. For every degree above 140°, the motor current limit is reduced by .55 amps until
the VSI controller reaches 158° F, at which time the current output is reduced to zero. This reduces your power chair’s
“power,” which could also reduce your power chair’s speed, and allows the electrical components and motors to cool
down. When the temperature returns to a safe level, your power chair resumes its normal operation.
VSI Error Codes
The VSI controller is designed with the user’s safety as the prime consideration. It incorporates many sophisticated selftest features which search for potential problems at a rate of 100 times per second. If the VSI detects a problem either in
its own circuits or in the power chair’s electrical system, it may stop the power chair, depending on the severity of the
problem. The VSI is designed to maximize the user’s safety under all normal conditions. The table below identifies the
individual error codes. Error codes are displayed as a rapid flashing of the lights. If you get one of these error codes,
contact your authorized Pride Provider.
FLASHING
LIGHTS
1
DIAGNOSIS AND SOLUTION
The batteries need charging or there is a bad connection to the batteries. Check the connections to the
batteries. If the connections are good, try charging the batteries.
2
The left motor has a bad connection. Check the left motor connection.
3
The left motor has a short circuit to a battery connection. Contact your authorized Pride Provider.
4
The right motor has a bad connection. Check the right motor connection.
5
The right motor has a short circuit to a battery connection. Contact your authorized Pride Provider.
6
The power chair is being inhibited by the battery charger. Unplug the battery charger.
7
A joystick fault is indicated. Make sure that the joystick is in the neutral (center) position before
turning on the controller.
8
A controller system fault is indicated. Make sure that all connections are secure.
9
The parking brakes have a bad connection. Check the parking brake and motor connections.
Make sure the controller connections are secure.
10
An excessive voltage has been applied to the controller. This is usually caused by a poor battery
connection. Check the battery connections.
38
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
REMOTE PLUS CONTROLLER
The electronic controller is what you use to operate your power chair. The electronic controller enables you to move the
power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system.
The Remote Plus is part of a modular electronic controller system. The system consists of more than one module. Typically, the Remote Plus is mounted to one of the armrests. See figure 34. It is connected to a power module located on the
power base through the controller communications cable.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If
it is programmed incorrectly or outside of the safe limits as determined by your healthcare
professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized
representative of the manufacturer, or a trained service technician should program the controller.
The Remote Plus consists of the following:
1. joystick
2. keypad
3. controller communications cable
4. off-board charger/programming socket
1
Joystick
The joystick controls the direction and speed of your power
chair. When you move the joystick from the neutral (center) position, the electromagnetic brakes release and allow
your power chair to move. The farther you push the joystick from its neutral position, the faster your power chair
moves. When you release the joystick and allow it to return
to the neutral position, you engage the electromagnetic
brakes. This causes your power chair to decelerate and
come to a complete stop.
2
3
4
Figure 34. Remote Plus Controller
WARNING! If your power chair begins to move in an unexpected manner, immediately release the
joystick. Unless the joystick is damaged, this action should stop your power chair.
Keypad
The keypad is located directly in front of the joystick. It contains keys that you will use to control your power chair. See
figure 35.
On/Off Key
The on/off key turns the system on and off.
Jazzy 1113 ATS
www.pridemobility.com
39
VII.
OPERATION
WARNING! Unless faced with an emergency
situation, do not use the on/off key to stop
the chair. This will cause the power chair
to stop abruptly.
WARNING! Always turn the power off when
you are stationary to prevent unexpected
movement.
Mode Key (Speed Settings)
The mode key controls the speed settings. The Remote Plus
speed settings range from 1 to 5. Typically, the slowest speed
setting is 1 and the fastest speed setting is 5. The settings
are indicated by the number of lights that are lit on the speed
setting indicator.
NOTE: The speed settings are preset at the factory. If
your authorized Pride Provider changes the order of these
settings, please make note of these changes. Contact your
authorized Pride Provider for more information.
Speed Setting Indicator
Indicates the selected speed setting.
To select a speed setting:
Figure 35. Remote Plus Keypad
1. Press the on/off key to power on the controller.
2. Press the mode key once.
3. To increase power chair speed, push the joystick to the right. Each time you push the joystick, you will
increase thespeed setting in the speed setting indicator.
4. To decrease power chair speed, push the joystick to the left. Each time you push the joystick, you will
decrease the speed setting in the speed setting indicator.
5. Once you select the desired speed setting, press themode key once to keep the setting or push the joystick in
the forward or reverse direction. The chair will resume operation at the selected speed.
NOTE: We recommend that the first few times you operate your power chair, you have your speed on
the slowest setting until you become familiar with your new power chair.
Horn Key
The horn key activates the horn.
Right/Left Turn Indicator Keys
The right/left turn indicator keys toggle either the left or right turn indicators. Press once to turn on and press again
to turn off. You can also turn off the selected indicator by pressing the opposite indicator key or the hazard key.
40
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
Light Key
The light key turns headlights/taillights on and off independent of other indicators.
Hazard Key
The hazard key activates both indicators at the same time. You can only cancel this by pressing the hazard key again.
Power Accessory Indicator
Indicates the selected power accessory. This is for optional accessories only.
Battery Condition Meter
The battery condition meter is a 10-segment illuminated display located in front of the joystick. When the lights are on, it
indicates that there is power to the Remote Plus. The lights also indicate battery status, Remote Plus operational status, and
electrical system status.
! Red, yellow, and green lights lit: Batteries charged; controller and electrical system OK.
! Red and yellow lights lit: Charge batteries if possible; controller and electrical system OK.
! Red lights only lit or slow flash: Charge batteries as soon as possible; controller and electrical system OK.
! Rapid flash of lights: Indicates an error in the controller or the electrical system. See “Remote Plus Error Codes.”
! Ripple up and down of lights: The joystick was not in the neutral position when the controller was turned on. If you
get “ripple up and down of lights,” turn off the controller and allow the joystick to return to the neutral position. Then
turn on the controller.
NOTE: If you still get “ripple up and down of lights,” contact your authorized Pride Provider.
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, reminding you the batteries need to be charged immediately!
Off-board Charger/Programming Socket
The off-board charger/programming socket is located on the front of the Remote Plus. If you use an off-board charger, the
charger current should not exceed 8 amps. Contact your authorized Pride Provider for more information.
WARNING! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/
programming socket. See your authorized Pride Provider for more information.
NOTE: Changes to the programming can only be made by the manufacturer, an authorized representative of
the manufacturer, or an authorized Pride Provider.
Controller Communications Cable
The controller communications cable provides the Remote Plus with a connection to the power module.
Power Module (Not Shown)
Typically, the power module is mounted to the power base. The power module provides a power interface for the joystick
module. It routes the battery power to the motors and other powered accessories such as lights and power seats.
Jazzy 1113 ATS
www.pridemobility.com
41
VII.
OPERATION
Actuator Lighting Module (Not Shown)
The actuator lighting module is also located on the power base. The actuator lighting module provides a control and power
interface between the power module, the lights, and/or the power seat actuator.
Sleep Mode
Your Remote Plus controller has a sleep mode feature. Sleep mode is a built-in circuit that automatically shuts off the main
power if the joystick is not moved in any direction for approximately five minutes. The battery condition meter lights on the
keypad indicate sleep mode by blinking once every five seconds. To restore power and continue, push the on/off key twice.
Thermal Rollback
The Remote Plus is equipped with a thermal rollback circuit. This circuit monitors the temperature of the motors, power module,
and remote. In the event that any of them become excessively hot (above 122° F), motor voltage is reduced. For every degree
above 122° F, the voltage is reduced by 5 volts. This reduces your power chair’s speed and allows the electrical components to
cool down. When the temperature returns to a safe level, your power chair resumes its normal speed.
Remote Plus Error Codes
In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible problems
with your power chair’s electrical system. If any of the battery condition meter lights are flashing rapidly, the controller may
be indicating an error. Error codes are displayed as a number of flashing lights. For instance, if the first light is flashing
rapidly, the battery voltage is nearly depleted. The table below identifies the individual error codes, probable causes, and
possible solutions. If you get one of these error codes, contact your authorized Pride Provider.
FLASHING LIGHTS
10
9
8
7
6
5
4
3
2
1
42
DIAGNOSIS
SOLUTION
High Battery Voltage
Solenoid Brake Fault
Possible Controller Fault
Possible Joystick Fault
Inhibit Active
Right Motor Wiring Fault
Right Motor Disconnected
Left Motor Wiring Fault
Left Motor Disconnected
Low Battery Voltage
Check batteries.
Check motor/brake wiring.
See authorized Pride Provider.
See authorized Pride Provider.
Unplug charger. Check connections.
Check right motor wiring.
Check right motor wiring.
Check left motor wiring.
Check left motor wiring.
Check batteries/battery wiring.
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
DYNAMIC DX CONTROLLER
The electronic controller is what you use to operate your power chair. The electronic controller enables you to move the
power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system.
The Dynamic DX is part of a modular electronic controller system. The system consists of more than one module. Typically, the Dynamic DX is mounted to one of the armrests. See figure 36. It is connected to a power module located on the
power base through the controller communications cable. The other components are located inside the power base.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If it
is programmed incorrectly or outside of the safe limits as determined by your healthcare professional,
it can create a dangerous situation. Only the power chair manufacturer, an authorized representative
of the manufacturer, or a trained service technician should program the controller.
The Europa master remote consists of the following :
1. joystick
2. keypad
3. controller communications connector
4. off-board charger/programming socket
2
3
1/0
Joystick
The joystick controls the direction and speed of the power chair.
When you move the joystick from the neutral (center) position,
the electromagnetic brake will release and allow the power chair
to move. The farther you push the joystick from its neutral position,
the faster your power chair will move. When you release the joystick
and allow it to return to the neutral position, you engage the
electromagnetic brake. This helps the power chair decelerate and
come to a complete stop. You can also use the joystick to control
power actuators.
1
4
Figure 36. Europa Master Remote
WARNING! If your power chair begins to move in an unexpected manner, immediately release the
joystick. Unless the joystick is damaged, this action should stop your power chair.
Out Of Neutral At Power Up
Your power chair joystick is equipped with Out Of Neutral At Power Up (OONAPU). If you power up the system and
the joystick is not in the neutral position, the system status light flashes rapidly for either as long as the joystick is out of the
neutral position or five seconds. If this has happened and all the segments on the battery condition meter are flashing, you
may have set a fault code. See “Europa Error Codes.”
Jazzy 1113 ATS
www.pridemobility.com
43
VII.
OPERATION
Keypad
The keypad is located directly in front of the joystick. It contains
keys that you will use to control your power chair. See figure 37.
On/Off Key
The on/off key toggles the system power on and off.
WARNING! Unless faced with an emergency situation, do not use the on/off key to stop the chair. This
will cause the power chair to stop abruptly.
WARNING! Always turn the power off when you are
stationary to prevent unexpected movement.
NOTE: If the joystick is not in the neutral (center) position
when you turn on the power, you may cause a fault in the
system. See “Out Of Neutral At Power Up.”
System Status Light
The system status light is normally on when the system is powered
up, and off when the system is powered down. It will also flash trouble
codes when the system detects a fault. See “Europa Error Codes.”
Figure 37. Europa Master Remote Keypad
Magnetic Locking Area
Your power chair is equipped with a feature that enables you to
“lockout” unauthorized users. For this function, you will need the magnetic key supplied with your power chair. If you lose
this key, contact your authorized Pride Provider.
To enable the lockout system:
1. Hold the magnetic key on or near the key symbol. The system will beep and automatically turn off.
NOTE: None of the remote lights should be lit.
2. Press the on/off key to turn on the power chair. The key symbol will flash, but you will not be able to drive your power
chair. This means that it is still locked.
3. Hold the magnetic key on or near the key symbol again to unlock the system. When the key symbol stops flashing, you
may turn on the power chair.
NOTE: If you turn on the power chair while it is locked and do not unlock it after one minute, the power chair
will automatically turn off itself.
44
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
Battery Condition Meter
The battery condition meter consists of six lights arranged in an arc over the battery icon. From left to right, the first two are
red, the second two are orange, and the last two are green. These lights give you an accurate indication of your usable
battery capacity. If the battery has at least 85% of its rated capacity, all of the lights will be on. As the battery voltage
drops, the number of lights reduces from right to left. When the battery capacity drops to 10% or below, all of the lights will
flash once every second.
Drive Program Select Key
The drive program select key enables you to select a drive program and an actuator mode. Your Dynamic DX controller
was preprogrammed at the factory for five drive programs— 1 (slowest) to 5 (fastest). The drive mode is indicated by a
number in the center of the keypad.
NOTE: The drive mode settings are preset at the factory. If your authorized Pride Provider changes these
settings, please make note of these changes.
To change the drive mode program:
1. Press the drive mode select key.
2. Move the joystick right to increase the drive mode program.
3. Move the joystick left to decrease the drive mode program.
4. Press the drive mode select key.
Drive Mode and Actuator Display (also Remote Status Display)
This is a seven-segment light that displays the drive program. It also displays a drive inhibit and actuator mode (if applicable)
when they occur.
Actuator Select Keys with Lights
If your power chair is equipped with power accessories such as a power seat or power elevating leg rests, you can
operate them through the remote keypad. Contact your authorized Pride Provider for information on how to operate these
accessories.
Remote Status Light
This light will flash if there is an internal Dynamic DX Remote fault, or if an OONAPU fault has occurred. See “Out Of
Neutral At Power Up.”
Horn Key
The horn key activates the horn.
Battery Saver Feature
When the battery capacity drops to below 21V (typically two lights), the controller will reduce power chair performance
to conserve battery power.
Off-board Charger/Programming Socket
You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front of the
Europa. See figure 36. If you use an off-board charger, the charger current should not exceed 8 amps. Contact your
authorized Pride Provider for more information.
Jazzy 1113 ATS
www.pridemobility.com
45
VII.
OPERATION
NOTE: The socket may also be used for reprogramming the Europa. Contact your authorized Pride Provider
for more information.
Sleep Mode (If Enabled)
The power chair controller features a sleep mode. Sleep mode is a built-in circuit that will automatically shut off the main
power if the joystick is not moved in any direction for a period of time. This time factor is programmed into the controller.
To restore power and continue, push and key on the keypad.
Europa Error Codes
The system status LED is displayed within the on/off key. This LED is lit if the system is turned on. It also flashes in groups
called flash codes, to indicate system faults. The table below identifies the individual fault codes. If your keypad displays
one of these codes, contact your authorized Pride Provider.
FLASH CODE
SEQUENCE
DIAGNOSIS
SOLUTION
•—•—•—
DX module fault
See your authorized Pride Provider.
••—••—••—
DX accessory fault
See your authorized Pride Provider.
•••—•••—
Left motor (or connection) fault
Check left motor wiring.
••••—••••—
Right motor (or connection) fault
Check right motor wiring.
•••••—•••••—
Left park brake fault
Check motor/brake wiring.
••••••—••••••—
Right park brake fault
Check motor/brake wiring.
•••••••—•••••••—
Low battery fault
Check that the battery wiring is secure.
•••••••—•••••••—
Over voltage fault
Check that the battery wiring is secure.
•••••••—•••••••—
CANL fault
See your authorized Pride Provider.
•••••••—•••••••—
CANA fault
See your authorized Pride Provider.
•••••••—•••••••—
Stall timeout
Turn unit on, then off.
•••••••—•••••••—
Module mismatch
See your authorized Pride Provider.
NOTE: You must turn the controller off and then on again to reset the controller, even if the source of the fault is
removed/corrected.
In the event of a fault, the system status LED displays diagnostic indications. Faults are encoded as follows: one (for a low
battery voltage fault) to twelve (module mismatch) and are displayed by the LED flashing the number of times prescribed
by the fault code. The flash sequence (one to twelve) is followed by a long off period (2 seconds). If more than one fault
exists, then the fault having the highest priority is indicated. The controller must be turned off and then on again even if the
source of the fault is removed. If you cannot resolve the problem, contact your authorized Pride Provider.
46
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
THE MICRODRIVE CONTROLLER
The electronic controller is what you use to operate your power chair. It takes the battery voltage and sends it to the
appropriate system. The electronic controller also enables you to monitor battery charge, electronic controller functions,
and the condition of your electrical system. Also, it may be used to control some optional systems such as power elevating
seats and lights. The Microdrive electronic control system is a modular system. The electronics necessary to operate your
power chair are contained in several modules located on different parts of your power chair. Typically, the Microdrive is
mounted to one of the armrests. See figure 38. The other components are located on or inside the power base.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If
it is programmed incorrectly or outside of the safe limits as determined by your healthcare
professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized
representative of the manufacturer, or a trained service technician should program the controller.
The Microdrive Controller consists of:
1. joystick
2. display pad
3. mode switch
4. on/off switch
5. speed adjustment dial
6. joystick interface module
7. off-board charger/programming socket
Joystick
The joystick controls the direction and speed of your power
chair. When you move the joystick from the neutral (center) position, the electromagnetic brakes release and allow
the power chair to move. The farther you push the joystick
from its neutral position, the faster the power chair moves.
When you release the joystick and allow it to return to the
neutral position, the electromagnetic brakes engage and
the power chair comes to a complete stop.
WARNING! If your power chair begins
to move in an unexpected manner,
immediately release the joystick.
Unless the joystick is damaged, this
action should stop your power chair.
Figure 38. Microdrive Controller with Joystick Interface
Module
Jazzy 1113 ATS
www.pridemobility.com
47
VII.
OPERATION
Display Pad
The display pad is located directly in front of the joystick. It contains the horn key, battery condition meter, profile/speed
indicator, and the actuator indicator. See figure 39.
Horn Key
The horn key activates the horn.
Battery Condition Meter
The battery condition meter is a 10-segment illuminated display that indicates that the Microdrive is powered on and also
gives the status of the batteries, the controller, and the power chair electrical system.
! Red, yellow, and green lights lit: Batteries charged; controller and electrical system OK.
! Red and yellow lights lit: Charge batteries if possible; controller and electrical system OK.
! Red lights only lit or slow flash: Charge batteries as soon as possible; controller and electrical system OK.
! Rapid flash of lights: Indicates a fault in the controller or the electrical system. See “Microdrive Error Codes.”
! Ripple side to side of lights: The joystick was not in the neutral position when the controller was turned on. If you
get “ripple side to side of lights,” turn off the controller, allow the joystick to return to the neutral position, then turn on
the controller.
NOTE: If you still get “ripple side to side of lights,” contact your authorized Pride Provider.
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, reminding you the
batteries need to be charged immediately!
Profile and Speed Indicator
The profile and speed indicator is a 5-segment illuminated display that indicates speed setting as well
as drive profile.
Actuator Indicator
The actuator indicator is a 4-segment illuminated
display that indicates power recline, power tilt,
power leg rest, and power elevating seat actuator
modes.
Joystick Interface Module
The joystick interface module provides a means to
enable or disable the horn button, mode switch, on/
off switch, and speed adjustment dial.
NOTE: When a toggle switch is set to “J/S,”
the joystick has control of a particular function. When the toggle switch is set to “Local,”
control of this function is disabled at the joystick.
Figure 39. Microdrive Display Pad
48
www.pridemobility.com
Jazzy 1113 ATS
VII.
OPERATION
Drive Profile Selection
Your Microdrive controller may be programmed for more than one drive profile that allows the system to be custom
tailored to your environment.
To select a profile setting:
1. Use the on/off switch to power on the chair and the controller.
2. Press the mode switch.
3. Move the joystick left or right to select the desired drive profile. Each of the LEDs indicate a separate profile.
NOTE: The system can be programmed with 5 different profiles.
Speed Adjustment
The Microdrive controller provides a speed control knob to control the speed of the power chair.
To change the speed:
1. Use the on/off switch to power on the chair and the controller.
2. To increase your speed, turn the speed adjustment dial clockwise.
3. To decrease your speed, turn the speed adjustment dial counterclockwise.
Sleep Mode
The Microdrive controller offers a sleep mode feature which will shut off the main power if the joystick remains stationary
for a period of five minutes. The battery condition meter will indicate sleep mode by blinking once every five seconds. To
restore power and resume operation of the chair, flip the on/off switch twice.
Thermal Rollback
The Microdrive controller is equipped with a thermal rollback circuit which monitors the temperature of the chair’s motors
and controller. If either exceeds 122° F, the controller reduces the motor voltage by 5 volts for every degree over. This
reduces the chair’s speed and allows a cool down period. Once the temperature returns to a safe level, the chair will
resume normal operation.
Microdrive Error Codes
In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible problems
with your power chair’s electrical system. If any of the battery condition meter lights are flashing rapidly, the controller may be
indicating an error. Error codes are displayed as a number of flashing lights. For instance, if the first light is flashing rapidly, the
battery voltage is nearly depleted. The following table identifies the individual error codes, probable causes, and possible
solutions. If you get one of these error codes, contact your authorized Pride Provider.
Jazzy 1113 ATS
www.pridemobility.com
49
VII.
FLASHING LIGHTS
10
9
8
7
6
5
4
3
2
1
50
OPERATION
DIAGNOSIS
High Battery Voltage
Solenoid Brake Fault
Possible Controller Fault
Possible Joystick Fault
Inhibit Active
Right Motor Wiring Fault
Right Motor Disconnected
Left Motor Wiring Fault
Left Motor Disconnected
Low Battery Voltage
www.pridemobility.com
SOLUTION
Check batteries.
Check motor/brake wiring.
See authorized Pride Provider.
See authorized Pride Provider.
Unplug charger. Check connections.
Check right motor wiring.
Check right motor wiring.
Check left motor wiring.
Check left motor wiring.
Check batteries/battery wiring.
Jazzy 1113 ATS
VIII.
CARE
AND
MAINTENANCE
CARE AND MAINTENANCE
Your Jazzy 1113 ATS is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks.
You can perform some of these checks, but others require assistance from your authorized Pride Provider. Preventive
maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that
your power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or
operation, contact your authorized Pride Provider.
WARNING! Prevent injury. Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas of any
kind.
WARNING! Direct exposure to water or dampness could cause the power chair to malfunction
electronically and mechanically. Water can cause electrical components to corrode and the chair’s
frame to rust.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to your authorized Pride Provider.
Temperature
! Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your power
chair between the temperatures of 18° F and 122° F.
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a
number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell).
! Temperatures above 122° F may cause your power chair to operate at a reduced speed. This reduced speed is a
safety feature built into the controller that helps prevent damage to the motor and other electrical components.
General Guidelines
! Avoid knocking or bumping the controller, especially the joystick.
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
! Keep the controller clean.
! Check all connectors to ensure that they are all tight and secured properly.
! Make sure the pneumatic tires are inflated to 35 psi (2.4 bar) if equipped with pneumatic tires..
WARNING! Overinflating tires can cause them to explode and can result in personal injury.
WARNING! Do not use a high pressure hose to inflate your tires.
! Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain
its high-gloss appearance.
Jazzy 1113 ATS
www.pridemobility.com
51
VIII.
CARE
AND
MAINTENANCE
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery
boxes and battery well frame with the battery terminals facing inward toward each other. Refer to the battery wiring
label for the correct wiring layout.
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
Daily Checks
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral
position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the boot.
Do not handle or try to repair it. See your authorized Pride Provider if there is a problem.
! Visually inspect the controller communications cable. Make sure that it is not frayed, cut, or has any wires exposed.
See your authorized Pride Provider if there is a problem.
! Check for flat spots on solid tires. Flat spots could adversely affect stability.
Weekly Checks
! Disconnect and inspect the controller and the charger harness from the electronics tray. Look for corrosion. Contact
your authorized Pride Provider if necessary.
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see your
authorized Pride Provider for replacement of the tube.
! Check the brakes. This test should be carried out on a level surface with at least 3 feet of clearance around your power chair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick. You must be
able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this test three times,
pushing the joystick backward, then left, and then right.
Monthly Checks
! Check that the anti-tip wheels do not rub the ground when you operate the power chair. Adjust them as necessary.
! Check for extreme wear on the anti-tip wheels. Replace them as necessary.
! Check for drive tire wear. See your authorized Pride Provider for repair.
! Check the caster wheels for wear. Replace them as necessary.
! Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings
replaced. See your authorized Pride Provider for repair.
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to your authorized Pride Provider for yearly maintenance. This helps ensure that your power chair
is functioning properly and helps prevent future complications.
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries
from the power chair. See VI. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
52
www.pridemobility.com
Jazzy 1113 ATS
VIII.
CARE
AND
MAINTENANCE
Disposal of Your Power Chair
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact your local
waste disposal agency or authorized Pride Provider for information on proper disposal of power chair packaging, metal
frame components, plastic components, electronics, and batteries.
Cleaning and Disinfection
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair. Avoid using
products that may scratch the surface of your power chair.
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your
product before application.
WARNING! Prevent personal injury and product damage! Follow all safety instructions for the
proper use of the disinfectant before applying it to your product.
WARNING! Never hose off your power chair or place it in direct contact with water. Your power
chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp
cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, replace the tube. If your chair is equipped with a solid tire insert, then
you must replace the whole wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available through
your authorized Pride Provider.
WARNING! To avoid possible injury, be sure that the controller’s power is turned off and the
power chair is not in freewheel mode before performing this procedure.
WARNING! Completely deflate the tire before attempting repair.
TIRE
AXLE KEY
WHEEL HUB
TUBE
DRIVE WHEEL
NUT
FRONT
RIM HALF
AXLE SLOT
REAR RIM
HALF
NUTS
DRIVE WHEEL WASHER
Figure 40. Drive Wheel
WASHERS
Figure 41. Drive Wheel Disassembled
Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:
1. Turn off the power to the controller.
2. Set the power chair up on blocks.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 40.
Jazzy 1113 ATS
www.pridemobility.com
53
VIII.
CARE
AND
MAINTENANCE
5. Pull the wheel off the axle.
6. Remove the nuts and washers from the wheel hub and separate the front and rear rim. See figure 41.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid
tire.
8. Reassemble the rims and reinstall the nuts and washers to the wheel hub.
9. Slide the wheel back onto the axle. Make sure the key is in the axle slot.
10. Reinstall the drive wheel nut and washer onto the axle and tighten.
11. Inflate the pneumatic tire to 35 psi (2.4 bar).
12. Remove the power chair from the blocks.
Battery Replacement
A battery wiring diagram is printed on a decal located on the battery well frame. Refer to the specifications table for correct
battery specifications.
WARNING! Prevent injury. Do not replace the battery when the seat is occupied.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Lifting beyond your capacity can result in personal injury.
WARNING! Prevent injury and/or equipment damage. Do not mix or match new and old batteries.
If you encounter a situation where one battery needs to be replaced, then replace both batteries.
Refer to specification table in this manual and the manual supplied with the battery charger for
recommended type and capacities.
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.”
3. Unplug the controller connector(s) from the power base.
4. Remove the seat.
5. Unplug the battery quick-connectors from the power base.
6. Unfasten the straps, remove the battery boxes from the battery well and open the lids.
7. Remove the old batteries.
8. Disconnect the wiring harnesses from the batteries.
9. Connect the wiring harness to the new batteries.
WARNING! Make sure you tighten the fasteners so that the connections are secure.
10. Place the new batteries into the battery boxes and replace the lids.
11. Place the battery boxes into the battery well on the power base and refasten the straps.
12. Plug in the quick-connectors.
13. Reinstall the seat.
14. Plug the controller connector(s) into the power base.
15. Charge the batteries.
54
www.pridemobility.com
Jazzy 1113 ATS
VIII.
CARE
AND
MAINTENANCE
When to See Your Authorized Pride Provider for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your authorized
Pride Provider. When calling, have the model number, serial number, nature of the problem, and the error code if available.
! Motor noise
! Frayed harnesses
! Cracked or broken connectors
! Uneven wear on any of the tires
! Jerky motion
! Pulling to one side
! Bent or broken wheel assemblies
! Does not power up
! Powers up, but does not move
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
! Check the harness connections. Make sure they are tight.
! Check the circuit breaker. Reset it if necessary.
! Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available
at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load
tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up,
contact your authorized Pride Provider.
Jazzy 1113 ATS
www.pridemobility.com
55
IX.
WARRANTY
LIFETIME LIMITED WARRANTY
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
Structural frame components, including:
! Main Frame
! Fixed-position seat post
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
Electronic components, including:
! Charger Assembly
! Controller
! Joystick
Other components, including:
! Foot riggings
Main frame assemblies, including:
! Anti-tip forks
! Caster forks
! Caster beam
! Metal seat framing
! Electrical Harness
! Foot rigging mounting brackets
18-MONTH LIMITED WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Motor/gearbox assembly
! Power seat actuator
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Accessories
! Brakes (electronic function ONLY)
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Bearings and bushings
! Plastic components, except body
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are not
warranted by Pride.
56
www.pridemobility.com
Jazzy 1113 ATS
IX.
WARRANTY
RECONDITIONED UNITS WARRANTY
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
! ABS Plastic shrouds
! Motor brushes
! Upholstery and seating
! Brake Pads
! Tires and tubes
! Fuses/Bulbs
! Circumstances beyond the control of Pride
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically authorized, IN
ADVANCE, by Pride Mobility Products Corporation
! Repairs and/or modifications made to any part without specific consent from Pride
Exclusions also include components with damage caused by:
! Contamination
! Abuse, misuse, accident, or negligence
! Battery fluid spillage or leakage
! Commercial use, or use other than normal
! Improper operation, maintenance, or storage
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in
cold conditions for an extended period of time, or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by an authorized Pride Provider. Do not return faulty parts to Pride without prior
written authorization. All transportation costs and shipping damage incurred while submitting parts for repair or replacement
are the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride product can
result in personal injury or product damage and will void Pride’s product warranty.
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from
the date of purchase and to the extent permitted by law. Any and all implied warranties are excluded. This is the exclusive
remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation
incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible technical
Jazzy 1113 ATS
www.pridemobility.com
57
NOTES
58
www.pridemobility.com
Jazzy 1113 ATS
#
In Q 1
Conuality
trol
Quality Control-Jazzy 1113 ATS
Thank you for making the Pride Jazzy 1113 ATS your choice in power chairs.
We have thoroughly inspected your Jazzy 1113 ATS. The following checkmarks indicate that it
has been test driven and inspected.
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*INFMANU1801*
Product Serial #