Datasheet | Siemens Model 240 Technical data

SINAMICS G120
Control Units CU240B-2
Control Units CU240E-2
Parameter Manual · 01/2011
SINAMICS
s
s
Parameters
Function diagrams
SINAMICS
Faults and Alarms
SINAMICS G120
Control Units CU240B/E-2
Appendix
List of Abbreviations
Parameter Manual
Valid for
Index
Firmware version
Control Units
CU240B-2
4.4
CU240B-2 DP
4.4
CU240E-2
4.4
CU240E-2 DP
4.4
CU240E-2 F
4.4
CU240E-2 DP F
4.4
A5E02631767B AC
01/2011
1
2
3
A
B
C
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to
prevent damage to property. The notices referring to your personal safety are highlighted in the manual
by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These
notices shown below are graded according to the degree of danger.
Danger
indicates that death or severe personal injury will result if proper precautions are not taken.
Warning
indicates that death or severe personal injury may result if proper precautions are not taken.
Caution
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not
taken.
Caution
without a safety alert symbol, indicates that property damage can result if proper precautions are not
taken.
Notice
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning
relating to property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning
and operation of a device/system may only be performed by qualified personnel. Within the context of
the safety notes in this documentation qualified persons are defined as persons who are authorized to
commission, ground and label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage of Siemens Products
Note the following:
Warning
This device may only be used for the applications described in the catalog or the technical description and
only in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens.
Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as
well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights
of the owner.
Copyright Siemens AG 2011 All Rights Reserved
Disclaimer of Liability
The distribution and duplication of this document or the utilization and
transmission of its contents are not permitted without express written
permission. Offenders will be liable for damages. All rights, including
rights created by patent grant or registration of a utility model or
design, are reserved.
We have reviewed the contents of this publication to ensure
consistency with the hardware and software described. Since
variance cannot be precluded entirely, we cannot guarantee full
consistency. However, the information in this publication is reviewed
regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 4848
90327 NUREMBERG
GERMANY
Siemens Aktiengesellschaft
© Siemens AG 2011
Technical data subject to change.
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11)
Contents
1
2
Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7
1.1
1.1.1
1.1.2
Introduction to Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanation of list of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Numerical ranges of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-8
1-8
1-15
1.2
List of Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-16
1.3
1.3.1
1.3.2
1.3.3
1.3.4
Command and Drive Data Sets – Overview . . . . . . . . . . . . . . . . . . . . .
Command Data Sets (CDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Data Sets (DDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Data Sets (MDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power unit Data Set (PDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-464
1-464
1-466
1-471
1-473
1.4
1.4.1
1.4.2
1.4.3
1.4.4
1.4.5
Connector/Binector (BICO)-Parameters . . . . . . . . . . . . . . . . . . . . . . . .
Binector Input Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Binector Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector/Binector Output Parameters . . . . . . . . . . . . . . . . . . . . . . . .
1-474
1-474
1-476
1-478
1-479
1-483
1.5
Quick commissioning (p0010 = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-485
Function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-487
2.1
Contents: function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-488
2.2
Explanations for the function diagrams . . . . . . . . . . . . . . . . . . . . . . . . .
2-493
2.3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-498
2.4
Input/Output Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-506
2.5
2.5.1
2.5.2
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fieldbus Interface (USS, Modbus) (CU240B/E-2). . . . . . . . . . . . . . . . .
PROFIdrive / PROFIBUS (CU240B/E-2 DP). . . . . . . . . . . . . . . . . . . . .
2-517
2-518
2-525
2.6
Internal control/status words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-539
2.7
Braking Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-557
2.8
Safety Integrated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-559
2.9
Setpoint channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-572
2.10
V/f control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-582
2.11
Vector control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-586
2.12
Free Function Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-606
2.13
Technology functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-627
2.14
Technology controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-629
2.15
Signals and monitoring functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-634
2.16
Faults and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-644
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Contents-5
Contents
2.17
Data sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-649
Faults and Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-653
3.1
3.1.1
3.1.2
3.1.3
Faults and Alarms – Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault reactions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgement of faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-654
3-654
3-656
3-657
3.2
List of Faults and Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-658
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-733
A.1
ASCII Table (excerpt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-734
A.2
List for motor code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-734
B
List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-735
C
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C-741
3
A
Contents-6
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1
Parameters
Contents
1.1
Introduction to Parameters
1.2
List of Parameters
1.3
Command and Drive Data Sets – Overview
1-464
1.4
Connector/Binector (BICO)-Parameters
1-474
1.5
Quick commissioning (p0010 = 1)
1-485
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-8
1-16
1-7
Parameters
Introduction to Parameters
1.1
Introduction to Parameters
1.1.1
Explanation of list of parameters
The layout of the parameter description is as follows (example only).
Index
r0068[0...1]
Fig. 1-1
BICO (if available)
CO: Absolute current actual value / I_act abs val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Unit group: 6_2
Unit selection: p0505
Min
Max
Factory setting
- [Arms]
- [Arms]
- [Arms]
Read-only parameter
Index
BICO (if available)
p0700[0...n]
Command source selection / Cmd src sel
CU240E-2
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: T
Scaling: -
Data set: CDS, p0170
Unit group:-
Unit selection: -
Min
0
Max
184
Factory setting
0
CU/PM variants
Fig. 1-2
Write parameter
Parameter number
Indicates the relevant parameter number. The numbers used are 4 to 5-digit numbers. Numbers prefixed with an “r” indicate that the parameter is a “read-only”
parameter, which displays a particular value but cannot be changed directly by
specifying a different value via this parameter number.
All other parameters are prefixed with a “p”. The values of these parameters can
be changed directly in the range indicated by the “Min” and “Max” settings in the
header. If these values have a physical unit, it is shown in brackets.
[index] indicates that the parameter is an indexed parameter and specifies the
range of indices available.
.0...15 indicates that the parameter has several bits, which can be evaluated or
connected individually.
CU/PM variants
Indicates for which Control Units and/or Power Modules the parameter is valid. If
no CUs or PMs are listed the parameter is valid for all variants.
1-8
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
Introduction to Parameters
Parameter text (Long name/Short name)
Indicates the name of the relevant parameter.
Certain parameter names include the following abbreviated prefixes: BI, BO, CI,
CO and CO/BO followed by a colon.
These abbreviations have the following meanings:
BI
=
BO
=
CI
=
CO
=
CO/BO =
P9999
(0)
Binector Input, i.e. parameter selects the source of a
binary signal
Binector Output, i.e. parameter connects as a binary
signal
r9999
r9999
(999:9)
Connector Input, i.e. parameter selects the source of an
analog signal
r9999 [99]
Connector Output, i.e. parameter connects as an analog
signal
r9999
r9999
Connector/Binector Output, i.e. parameter connects as
an analog signal and/or as a binary signal
CoBo.pdf
To make use of BICO you will need access to the full parameter list. At this level
many new parameter settings are possible, including BICO functionality. BICO
functionality is a different, more flexible way of setting and combining input and
output functions.
The BICO system allows complex functions to be programmed. Boolean and
mathematical relationships can be set up between inputs (digital, analog, serial
etc.) and outputs (inverter current, frequency, analog output, relays, etc.).
At BI and CI parameters the parameter number is specified under Factory setting
with which this parameter is connected. In this case the Min and Max values have
dashes.
Access level
Indicates the level of user access. For the parameters of all variants of Control
Units CU240B-2 and CU240E-2 there is only one freely accessible access level
effective. The parameters with the declaration "Access level 1“ to "Access level
3“ belong to them. Parameters with "Access level 4“ are service parameters and
password protected.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-9
Parameters
Introduction to Parameters
Data type
The data types available are shown in the table below.
Table 1-1
Available data types
Notation
Meaning
Unsigned8 (U8)
8-bit unsigned
Unsigned16 (U16)
16-bit unsigned
Unsigned32 (U32)
32-bit unsigned
Integer16 (I16)
16-bit integer
Integer32 (I32)
32-bit integer
FloatingPoint32 (Float)
32-bit floating point number
The information of the data types for binector and connector inputs can be composed of two specifications (discreated by a slash):
 First specification:
data type of the parameter
 Second specification:
data type of the signal source preferably to be connected (binector or connector output)
Depending on the data type of the BICO input parameter (signal sink) and BICO
output parameter (signal source) the following combinations are possible when
creating BICO interconnections:
Table 1-2
Possible combinations of BICO interconnections
BICO input parameter
CI parameter
BICO output parameter
BI parameter
Unsigned32 /
Integer16
Unsigned32 /
Integer32
Unsigned32 /
FloatingPoint32
Unsigned32 /
Binary
CO: Unsigned8
x
x
–
–
CO: Unsigned16
x
x
–
–
CO: Unsigned32
x
x
–
–
CO: Integer16
x
x
r2050
–
CO: Integer32
x
x
–
–
CO: FloatingPoint32
x
x
x
–
BO: Unsigned8
–
–
–
x
BO: Unsigned16
–
–
–
x
BO: Unsigned32
–
–
–
x
BO: Integer16
–
–
–
x
BO: Integer32
–
–
–
x
BO: FloatingPoint32
–
–
–
–
Legend:
x: BICO interconnection permitted
–: BICO interconnection not permitted
1-10
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
Introduction to Parameters
Scaling
Specification of the reference value with which a signal value is automatically converted for a BICO interconnection.
Reference quantities, corresponding to 100 %, are required for the statement of
physical units as percentages. These reference quantities are entered in parameters p2000 ... p2007.
In addition to p2000 ... p2007 the following scalings are used:
 PERCENT
 4000H
1.0 = 100 %
4000 hex = 100 %
Calculated
Specifies whether the parameter is influenced by automatic calculations.
p0340 defines the following calculations:
 p0340 = 1 contains the calculations of p0340 = 2, 3, 4, 5.
 p0340 = 2 calculates the motor parameters (p0350 ... p0360, p0625).
 p0340 = 3 contains the calculations of p0340 = 4, 5.
 p0340 = 4 only calculates the controller parameters.
 p0340 = 5 only calculates the controller limits.
Note:
For p3900 > 0, also p0340 = 1 is automatically called.
After p1900 = 1, 2, p0340 = 3 is automatically called.
Parameters referring to p0340 in the specification "Calculated" are dependent on
the applied Power Module and motor. In this case, the values of "Factory setting"
do not correspond to the actual values because these values are calculated
during the commissioning. This also applies to the motor parameters.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-11
Parameters
Introduction to Parameters
Can be changed
Inverter state in which the parameter is changeable. Three states are possible:
 Commissioning
C(x)
 Run
U
 Ready to run
T
In these states the parameter can be changed. One, two or all three states may
be specified. If all three states are specified, it is possible to change the parameter
setting in all three inverter states. (x) shows, that the parameter is only changeable when p0010 = x.
Data Set
Parameters which are dependent on a data set are identified as follows:
 CDS (Command Data Set)
They are always indexed with [0 ... n] (with n = 0 ... 3 depending on setting in
p0170).
[0] = Command Data Set 0
[1] = Command Data Set 1
etc.
 DDS (Drive Data Set)
They are always indexed with [0 ... n] (with n = 0 ... 3 depending on setting in
p0180).
[0] = Drive Data Set 0
[1] = Drive Data Set 1
etc.
 MDS (Motor Data Set) and PDS (Power unit Data Set)
They are always indexed with [0 ... n] (with n = 0 ... 3 depending on setting in
p0180). The Motor Data Sets and Power unit Data Sets are allocated to the Drive
Data Sets, i.e. they are automatically addressed with the selection of a Drive Data
Set (e.g. Drive Data Set 1 includes Motor Data Set 1 and Power unit Data Set 1).
Data sets can only be applied and cleared when p0010 = 15 is set.
1-12
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
Introduction to Parameters
"Unit group" and "Unit selection"
For parameters where the unit can be switched, the specifications for "Unit group"
and "Unit selection" determine the group to which this parameter belongs and with
which parameter the unit can be switched over.
The standard unit of a parameter is specified in square parentheses after the values for "Min", "Max", and "Factory setting".
Min
Indicates the minimum value to which the parameter can be set.
Max
Indicates the maximum value to which the parameter can be set.
Factory setting
Indicates the default value, i.e. the value which applies if the user does not specify
a particular value for the parameter (see also "Calculated“).
Example:
Unit group: 7_1, unit selection: p0505
The parameter belongs to unit group 7_1 and the unit can be switched over using
p0505.
All the potential unit groups and possible unit selections are listed below.
Table 1-3
Unit group (p0100)
Unit group
Unit selection for p0100 =
0
1
Reference value
at %
2
7_4
Nm
lbf ft
Nm
-
14_6
kW
HP
kW
-
25_1
kgm2
lb ft2
kgm2
-
27_1
kg
lb
kg
-
28_1
Nm/A
lbf ft/A
Nm/A
-
29_1
N/Arms
lbf/Arms
N/Arms
-
Table 1-4
Unit group (p0505)
Unit group
Unit selection for p0505 =
1
2
3
Reference value
at %
4
2_1
Hz
%
Hz
%
p2000
3_1
rpm
%
rpm
%
p2000
5_1
Vrms
%
Vrms
%
p2001
5_2
V
%
V
%
p2001
5_3
V
%
V
%
p2001
6_2
Arms
%
Arms
%
p2002
6_5
A
%
A
%
p2002
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-13
Parameters
Introduction to Parameters
Table 1-4
Unit group (p0505), continued
Unit group
Unit selection for p0505 =
1
2
3
Reference value
at %
4
7_1
Nm
%
lbf ft
%
p2003
7_2
Nm
Nm
lbf ft
lbf ft
-
14_5
kW
%
HP
%
r2004
14_10
kW
kW
HP
HP
-
21_1
°C
°C
°F
°F
-
21_2
K
K
°F
°F
-
39_1
1/s2
%
1/s2
%
p2007
Table 1-5
Unit group (p0595)
Unit group
Unit selection for p0595 =
Value
9_1
Unit
Reference value
at %
The values that can be set and the technological units are shown in
p0595 (see Chapter 1.2).
Description
Explanation of the parameter function.
Values
List of possible parameter values.
Recommendation
Information about recommended settings.
Index
The name and meaning of each individual index is specified for indexed parameters, except indexed parameters which belong to a data set (see "Data Set").
Bit array
For parameters with bit arrays, for each bit the following information is provided:
 Bit number and signal name
 Meaning at signal states 0 and 1
 Function diagram (FP) (optional). The signal is shown on this function diagram.
Dependency
Conditions which need to be fulfilled with regard to this parameter. Also includes
special effects which can occur between this parameter and others.
1-14
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
Introduction to Parameters
1.1.2
Numerical ranges of parameters
Note:
The following numerical ranges of the parameters describe a general overview of SINAMICS
parameters. The specific parameters are listed in Chapter 1.2.
Table 1-6
Numerical ranges of parameters
Range
Description
from
to
0000
0099
Operation and visualization
0100
0199
Commissioning
0200
0299
Power Module
0300
0399
Motor
0500
0599
Technology and units
0600
0699
Thermal motor protection and motor model, maximum current
0700
0799
Command sources and terminals on Control Unit
0800
0839
CDS, DDS data sets (e.g. switch over, copy)
0840
0879
Sequence control (e.g. source for ON/OFF1)
0880
0899
Control and status words
0900
0999
PROFIBUS/PROFIdrive
1000
1199
Setpoint channel
1200
1299
Functions (e.g. motor holding brake)
1300
1399
V/f control
1400
1799
Closed-loop control
1800
1899
Gating unit
1900
1999
Power Module and motor identification
2000
2099
Communication (PROFIBUS)
2100
2199
Faults and alarms, monitoring functions
2200
2399
Technology controller
3100
3299
Messages
3800
3860
Compound braking
3900
3999
Management parameters
7800
7899
EEPROM read/write parameters
8500
8599
Data and macro management
8800
8899
PROFIdrive
8900
8999
PROFINET, USB
9300
9399
Safety Integrated
9400
9499
Parameter consistency and storage
9500
9899
Safety Integrated
9900
9949
Topology
9950
9999
Diagnostics (internal)
10000
10199
Safety Integrated
20000
20399
Free Function Blocks (FFB)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-15
Parameters
List of Parameters
1.2
List of Parameters
Product: SINAMICS G120 CU240, Version: 4402100, Language: eng
Objects: CU240B-2, CU240B-2 DP, CU240E-2, CU240E-2 DP, CU240E-2 DP F, CU240E-2 F
r0002
Drive operating display / Drv op_display
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
200
Factory setting
-
Description:
Operating display for the drive.
Value:
0:
10:
12:
13:
14:
16:
17:
18:
19:
21:
22:
31:
35:
41:
42:
43:
45:
46:
70:
200:
Dependency:
Refer to: r0046
Notice:
For several missing enable signals, the corresponding value with the highest number is displayed.
Note:
OC: Operating condition
Operation - everything enabled
Operation - set "enable setpoint" = "1" (p1142)
Operation - RFG frozen, set "RFG start" = "1" (p1141)
Operation - set "enable RFG" = "1" (p1140)
Operation - MotID, excit. running
Operation - withdraw braking with OFF1 using "ON/OFF1" = "1"
Operation - braking with OFF3 can only be interrupted with OFF2
Operation - brake on fault, remove fault, acknowledge
Operation - DC braking active (p1230, p1231)
Ready for operation - set "Operation enable" = "1" (p0852)
Ready for operation - de-magnetizing running (p0347)
Ready for switching on - set "ON/OFF1" = "0/1" (p0840)
Switching on inhibited - carry out first commissioning (p0010)
Switching on inhibited - set "ON/OFF1" = "0" (p0840)
Switching on inhibited - set "OC/OFF2" = "1" (p0844, p0845)
Switching on inhibited - set "OC/OFF3" = "1" (p0848, p0849)
Switching on inhibited - rectify fault, acknowledge fault, STO
Switching on inhibited - exit comm mode (p0010)
Initialization
Wait for booting/partial booting
RFG: Ramp-function generator
COMM: Commissioning
MotID: Motor data identification
p0003
Access level / Acc_level
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C, U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
3
Max
4
Description:
Sets the access level to read and write parameters.
Value:
3:
4:
Note:
Access level 3 (experts):
Factory setting
3
Expert
Service
Expert know-how is required for these parameters (e.g. BICO parameterization).
Access level 4 (service):
For these parameters, it is necessary that authorized service personnel enter the appropriate password (p3950).
1-16
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0010
Drive commissioning parameter filter / Drv comm. par_filt
CU240B-2
Access level: 1
Calculated: -
Data type: Integer16
CU240B-2 DP
Can be changed: C(1), T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
49
Description:
Factory setting
1
Sets the parameter filter to commission a drive.
Setting this parameter filters out the parameters that can be written into in the various commissioning steps.
Value:
0:
1:
2:
3:
5:
15:
29:
30:
39:
49:
Ready
Quick commissioning
Power unit commissioning
Motor commissioning
Technological application/units
Data sets
Only Siemens internal
Parameter reset
Only Siemens internal
Only Siemens internal
Dependency:
Refer to: r3996
Notice:
When the parameter is reset to a value of 0, short-term communication interruptions may occur.
Note:
The drive can only be powered up outside the drive commissioning (inverter enable). To realize this, this parameter
must be set to 0.
By setting p3900 to a value other than 0, the quick commissioning is completed, and this parameter is automatically
reset to 0.
Procedure for "Reset parameter": Set p0010 to 30 and p0970 to 1.
Once the Control Unit has been booted up for the first time, the motor parameters suitable for the power unit have
been defined, and the control parameters have been calculated accordingly, p0010 is automatically reset to 0.
p0010 = 3 is used for the subsequent commissioning of additional drive data sets (creating data sets: see p0010 =
15).
p0010 = 29, 39, 49: Only for internal Siemens use!
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-17
Parameters
List of Parameters
p0010
Drive commissioning parameter filter / Drv comm. par_filt
PM230
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2
Can be changed: C(1), T
Scaling: -
Data set: -
CU240E-2 DP
Units group: -
Unit selection: -
Min
0
Max
49
CU240E-2 DP F
CU240E-2 F
Description:
Factory setting
1
Sets the parameter filter to commission a drive.
Setting this parameter filters out the parameters that can be written into in the various commissioning steps.
Value:
0:
1:
2:
3:
5:
15:
29:
30:
39:
49:
Ready
Quick commissioning
Power unit commissioning
Motor commissioning
Technological application/units
Data sets
Only Siemens internal
Parameter reset
Only Siemens internal
Only Siemens internal
Dependency:
Refer to: r3996
Notice:
When the parameter is reset to a value of 0, short-term communication interruptions may occur.
Note:
The drive can only be powered up outside the drive commissioning (inverter enable). To realize this, this parameter
must be set to 0.
By setting p3900 to a value other than 0, the quick commissioning is completed, and this parameter is automatically
reset to 0.
Procedure for "Reset parameter": Set p0010 to 30 and p0970 to 1.
Once the Control Unit has been booted up for the first time, the motor parameters suitable for the power unit have
been defined, and the control parameters have been calculated accordingly, p0010 is automatically reset to 0.
p0010 = 3 is used for the subsequent commissioning of additional drive data sets (creating data sets: see p0010 =
15).
p0010 = 29, 39, 49: Only for internal Siemens use!
1-18
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0010
Drive commissioning parameter filter / Drv comm. par_filt
PM240
Access level: 1
Calculated: -
Data type: Integer16
PM250
Can be changed: C(1), T
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
0
Max
95
CU240E-2
CU240E-2 DP
CU240E-2 DP F
CU240E-2 F
Description:
Factory setting
1
Sets the parameter filter to commission a drive.
Setting this parameter filters out the parameters that can be written into in the various commissioning steps.
Value:
0:
1:
2:
3:
5:
15:
29:
30:
39:
49:
95:
Ready
Quick commissioning
Power unit commissioning
Motor commissioning
Technological application/units
Data sets
Only Siemens internal
Parameter reset
Only Siemens internal
Only Siemens internal
Safety Integrated commissioning
Dependency:
Refer to: r3996
Notice:
When the parameter is reset to a value of 0, short-term communication interruptions may occur.
Note:
The drive can only be powered up outside the drive commissioning (inverter enable). To realize this, this parameter
must be set to 0.
By setting p3900 to a value other than 0, the quick commissioning is completed, and this parameter is automatically
reset to 0.
Procedure for "Reset parameter": Set p0010 to 30 and p0970 to 1.
Once the Control Unit has been booted up for the first time, the motor parameters suitable for the power unit have
been defined, and the control parameters have been calculated accordingly, p0010 is automatically reset to 0.
p0010 = 3 is used for the subsequent commissioning of additional drive data sets (creating data sets: see p0010 =
15).
p0010 = 29, 39, 49: Only for internal Siemens use!
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-19
Parameters
List of Parameters
p0014
Description:
Value:
Dependency:
Caution:
Notice:
Note:
Buffer memory mode / Buf mem mode
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
0
Sets the mode for the buffer memory.
0:
Save in a non-volatile fashion (RAM)
1:
Buffer memory active (non-volatile)
2:
Clear buffer memory
If p0014 = 1, changes in the same parameter, as well as in following parameters will not be copied to the buffer
memory:
Refer to: p0040, p0340, p0650, p0802, p0803, p0804, p0952, p0969, p0970, p0971, p0972, p1900, p1910, p1960,
p2111, p3900, p3981
Refer to: A01066, A01067
For p0014 = 2, entries in the buffer memory are lost and cannot be retrieved.
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
The parameter is not influenced by setting the factory setting.
Re p0014 = 0:
Parameter changes are saved in the volatile memory (RAM).
Non-volatile storage from RAM to ROM is carried out in the following cases:
- p0971 = 1
- change from p0014 = 0 to 1
Re p0014 = 1:
With this setting, alarm A01066 followed by alarm A01067 can occur if parameters are continually changed via a
fieldbus system.
Parameter changes are entered in the volatile memory (RAM) and also in the non-volatile buffer memory.
In the following cases, the entries in the buffer memory are transferred into the ROM and then the buffer memory is
cleared:
- p0971 = 1
- power down/power up the Control Unit
- change from p0014 = 1 to 0
Re p0014 = 2:
The procedure to clear the entries in the buffer memory is initiated.
p0014 is automatically set to 0 after the entries have been cleared.
p0015
Macro drive unit / Macro drv unit
CU240B-2
Access level: 1
Calculated: -
Data type: Unsigned32
CU240E-2
Can be changed: C, C(1)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0
Max
999999
Description:
Factory setting
12
Runs the corresponding macro files.
The selected macro file must be available on the memory card/device memory.
Example:
p0015 = 6 --> the macro file PM000006.ACX is run.
Dependency:
Refer to: p0700, p1000, p1500, r8570
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
The macros in the specified directory are displayed in r8570. r8570 is not in the expert list of the commissioning
software.
Macros available as standard are described in the technical documentation of the particular product.
The parameter is not influenced by setting the factory setting.
1-20
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0015
Macro drive unit / Macro drv unit
CU240B-2 DP
Access level: 1
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: C, C(1)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
999999
Description:
Factory setting
7
Runs the corresponding macro files.
The selected macro file must be available on the memory card/device memory.
Example:
p0015 = 6 --> the macro file PM000006.ACX is run.
Dependency:
Refer to: p0700, p1000, p1500, r8570
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
The macros in the specified directory are displayed in r8570. r8570 is not in the expert list of the commissioning
software.
Macros available as standard are described in the technical documentation of the particular product.
The parameter is not influenced by setting the factory setting.
r0018
Control Unit Firmware-Version / CU FW version
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
4294967295
Description:
Displays the firmware version of the Control Unit.
Dependency:
Refer to: r0197, r0198
Note:
Example:
Factory setting
-
The value 1010100 should be interpreted as V01.01.01.00.
r0020
Speed setpoint smoothed / n_set smth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the currently smoothed speed setpoint at the input of the speed controller or U/f characteristic (after the
interpolator).
Dependency:
Refer to: r0060
Note:
Smoothing time constant = 100 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The speed setpoint is available smoothed (r0020) and unsmoothed (r0060).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-21
Parameters
List of Parameters
r0021
CO: Actual speed smoothed / n_act smooth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the smoothed actual value of the motor speed.
Dependency:
Refer to: r0022, r0063
Note:
Smoothing time constant = 100 ms
Factory setting
- [rpm]
The signal is not suitable as a process quantity and may only be used as a display quantity.
The speed actual value is available smoothed (r0021, r0022) and unsmoothed (r0063).
r0022
Description:
Speed actual value rpm smoothed / n_act rpm smooth
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: -
Unit selection: -
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the smoothed actual value of the motor speed.
r0022 is identical to r0021, however, it always has units of rpm and contrary to r0021 cannot be changed over.
Dependency:
Refer to: r0021, r0063
Note:
Smoothing time constant = 100 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The speed actual value is available smoothed (r0021, r0022) and unsmoothed (r0063).
r0024
Output frequency smoothed / f_outp smooth
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: -
Unit selection: -
Min
- [Hz]
Max
- [Hz]
Description:
Displays the smoothed converter frequency.
Dependency:
Refer to: r0066
Note:
Smoothing time constant = 100 ms
Factory setting
- [Hz]
The signal is not suitable as a process quantity and may only be used as a display quantity.
The output frequency is available smoothed (r0024) and unsmoothed (r0066).
r0025
CO: Output voltage smoothed / U_outp smooth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [Vrms]
Max
- [Vrms]
Description:
Displays the smoothed output voltage of the power unit.
Dependency:
Refer to: r0072
Note:
Smoothing time constant = 100 ms
Factory setting
- [Vrms]
The signal is not suitable as a process quantity and may only be used as a display quantity.
The output voltage is available smoothed (r0025) and unsmoothed (r0072).
1-22
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0026
Description:
Dependency:
Notice:
Note:
r0027
Description:
Dependency:
Notice:
Note:
r0028
CO: DC link voltage smoothed / Vdc smooth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Factory setting
- [V]
Displays the smoothed actual value of the DC link voltage.
Refer to: r0070
When measuring a DC link voltage < 200 V, for the Power Module (e.g. PM240) a valid measured value is not supplied. In this case, when an external 24 V power supply is connected, a value of approx. 24 V is displayed in the display parameter.
Smoothing time constant = 100 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The DC link voltage is available smoothed (r0026) and unsmoothed (r0070).
r0026 sets itself to the lower value of the pulsating DC link voltage.
CO: Absolute actual current smoothed / I_act abs val smth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Displays the smoothed absolute actual current value.
Refer to: r0068
This smoothed signal is not suitable for diagnostics or evaluation of dynamic operations. In this case, the
unsmoothed value should be used.
Smoothing time constant = 300 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The absolute current actual value is available smoothed (r0027) and unsmoothed (r0068).
Modulation depth smoothed / Mod_depth smth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Dependency:
Note:
Displays the smoothed actual value of the modulation depth.
Refer to: r0074
Smoothing time constant = 100 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The modulation depth is available smoothed (r0028) and unsmoothed (r0074).
r0029
Current actual value field-generating smoothed / Id_act smooth
Description:
Dependency:
Note:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Displays the smoothed field-generating actual current.
Refer to: r0076
Smoothing time constant = 300 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The field-generating current actual value is available smoothed (r0029) and unsmoothed (r0076).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-23
Parameters
List of Parameters
r0030
Current actual value torque-generating smoothed / Iq_act smooth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Description:
Displays the smoothed torque-generating actual current.
Dependency:
Refer to: r0078
Note:
Smoothing time constant = 300 ms
Factory setting
- [Arms]
The signal is not suitable as a process quantity and may only be used as a display quantity.
The torque-generating current actual value is available smoothed (r0030) and unsmoothed (r0078).
r0031
Actual torque smoothed / M_act smooth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Description:
Displays the smoothed torque actual value.
Dependency:
Refer to: r0080
Note:
Smoothing time constant = 100 ms
Factory setting
- [Nm]
The signal is not suitable as a process quantity and may only be used as a display quantity.
The active current actual value is available smoothed (r0031) and unsmoothed (r0080).
r0032
CO: Active power actual value smoothed / P_actv_act smth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: r2004
Data set: -
Units group: 14_10
Unit selection: p0505
Min
- [kW]
Max
- [kW]
Factory setting
- [kW]
Description:
Displays the smoothed actual value of the active power.
Dependency:
Refer to: r0082
Notice:
This smoothed signal is not suitable for diagnostics or evaluation of dynamic operations. In this case, the
unsmoothed value should be used.
Note:
Power delivered at the motor shaft.
The active power is available smoothed (r0032 with 100 ms) and unsmoothed (r0082).
1-24
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0033
Description:
Dependency:
Note:
r0034
Description:
Dependency:
Note:
r0035
Description:
Note:
Torque utilization smoothed / M_util smooth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the smoothed torque utilization as a percentage.
The torque utilization is obtained from the required smoothed torque in reference to the torque limit, scaled using
p2196.
This parameter is only available for vector control. For U/f control r0033 = 0 %.
Smoothing time constant = 100 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
The torque utilization is available smoothed (r0033) and unsmoothed (r0081).
For M_set total (r0079) > 0, the following applies:
- Required torque = M_set total
- Actual torque limit = M_max upper effective (r1538)
For M_set total (r0079) <= 0, the following applies:
- Required torque = - M_set total
- Actual torque limit = - M_max lower effective (r1539)
For the actual torque limit = 0, the following applies: r0033 = 100 %
For the actual torque limit < 0, the following applies: r0033 = 0 %
CO: Motor utilization / Motor utilization
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the motor utilization from the thermal I2t motor model.
The motor utilization is only determined for permanent-magnet synchronous motors and if the I2t motor model is
activated.
The motor utilization is formed from the ratio between the I2t motor model temperature (minus 40 Kelvin) and the
reference value p0605 (motor overtemperature, fault threshold) - 40 Kelvin. If p0605 is reduced, r0034 increases
and the motor temperature remains the same.
Refer to: p0611, p0612, p0615
Smoothing time constant = 100 ms
The signal is not suitable as a process quantity and may only be used as a display quantity.
A value of r0034 = -200.0 % indicates an invalid display, for example, because the thermal I2t motor model was not
activated or was incorrectly parameterized.
CO: Motor temperature / Mot temp
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2006
Data set: -
Units group: 21_1
Unit selection: p0505
Min
- [°C]
Max
- [°C]
Factory setting
- [°C]
Displays the actual temperature in the motor.
For r0035 not equal to -200.0 °C, the following applies:
- this temperature display is valid.
- a KTY sensor is connected.
- for induction motors, the thermal motor model is activated (p0601 = 0).
For r0035 equal to -200.0 °C, the following applies:
- this temperature display is not valid (temperature sensor error).
- A PTC sensor or bimetallic NC contact is connected.
- for synchronous motors, the thermal motor model is activated (p0601 = 0).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-25
Parameters
List of Parameters
r0036
Description:
Dependency:
r0037[0...19]
CO: Power unit overload I2t / PU overload I2t
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the power unit overload determined using the I2t calculation.
A current reference value is defined for the I2t monitoring of the power unit. It represents the current that can be
conducted by the power unit without any influence of the switching losses (e.g. the continuously permissible current
of the capacitors, inductances, busbars, etc.).
If the I2t reference current of the power unit is not exceeded, then an overload (0 %) is not displayed.
In the other case, the degree of thermal overload is calculated, whereby 100% results in a trip.
Refer to: p0290, p0294
Refer to: F30005
CO: Power unit temperatures / PU temperatures
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2006
Data set: -
Units group: 21_1
Unit selection: p0505
Min
- [°C]
Max
- [°C]
Description:
Displays the temperatures in the power unit.
Index:
[0] = Inverter
[1] = Depletion layer
[2] = Reserved
[3] = Reserved
[4] = Interior of power unit
[5] = Inverter 1
[6] = Reserved
[7] = Reserved
[8] = Reserved
[9] = Reserved
[10] = Reserved
[11] = Reserved
[12] = Reserved
[13] = Depletion layer 1
[14] = Reserved
[15] = Reserved
[16] = Reserved
[17] = Reserved
[18] = Reserved
[19] = Reserved
Note:
The value of -200 indicates that there is no measuring signal.
r0038
Power factor smoothed / Cos phi smooth
Factory setting
- [°C]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the smoothed actual power factor.
Note:
Smoothing time constant = 300 ms
Factory setting
-
The signal is not suitable as a process quantity and may only be used as a display quantity.
Significance for the motor: Motor power factor
Significance for the infeed: Power factor at the connection point (p3470, p3471)
1-26
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0039
Energy consumption / Energy consumption
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [kWh]
Max
- [kWh]
Description:
Displays the electrical energy used since the last reset.
Dependency:
Refer to: p0040
p0040
Reset energy consumption display / Energy usage reset
Description:
Factory setting
- [kWh]
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Setting to reset the energy consumption display (r0039).
Procedure:
Set p0040 = 0 --> 1
The display is reset and the parameter is automatically set to zero.
Dependency:
Refer to: r0039
r0041
Energy usage saved / Energy usage saved
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [kWh]
Max
- [kWh]
Factory setting
- [kWh]
Description:
Displays the saved energy referred to 100 operating hours.
Dependency:
Refer to: p0040
p0045
Smoothing time constant, display values / T_smth display
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
1000.00 [ms]
Factory setting
4.00 [ms]
Sets the smoothing time constant for the following display values:
r0063[1], r0068[1], r0080[1], r0082[1].
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-27
Parameters
List of Parameters
r0046.0...31
CO/BO: Missing enable sig / Missing enable sig
Access level: 1
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays missing enable signals that are preventing the closed-loop drive control from being commissioned.
Bit field:
Bit
00
01
02
03
04
10
11
12
16
17
18
19
20
21
26
27
28
30
31
Dependency:
Refer to: r0002
1-28
Signal name
OFF1 enable missing
OFF2 enable missing
OFF3 enable missing
Operation enable missing
DC braking enable missing
Ramp-function generator enable missing
Ramp-function generator start missing
Setpoint enable missing
OFF1 enable internal missing
OFF2 enable internal missing
OFF3 enable internal missing
Pulse enable internal missing
DC braking internal enable missing
PU enab. missing
Drive inactive or not operational
De-magnetizing not completed
Brake open missing
Speed controller inhibited
Jog setpoint active
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
Note:
The value r0046 = 0 indicates that all enable signals for this drive are present.
Bit 00 = 1 (enable signal missing), if:
- the signal source in p0840 is a 0 signal.
- there is a "switching on inhibited".
Bit 01 = 1 (enable signal missing), if:
- the signal source in p0844 or p0845 is a 0 signal.
Bit 02 = 1 (enable signal missing), if:
- the signal source in p0848 or p0849 is a 0 signal.
Bit 03 = 1 (enable signal missing), if:
- the signal source in p0852 is a 0 signal.
Bit 04 =1 (DC brake active) when:
- the signal source in p1230 has a 1 signal
Bit 10 = 1 (enable signal missing), if:
- the signal source in p1140 is a 0 signal.
Bit 11 = 1 (enable signal missing) if the speed setpoint is frozen, because:
- the signal source in p1141 is a 0 signal.
- the speed setpoint is entered from jogging and the two signal sources for jogging, bit 0 (p1055) and bit 1 (p1056)
have a 1 signal.
Bit 12 = 1 (enable signal missing), if:
- the signal source in p1142 is a 0 signal.
Bit 16 = 1 (enable signal missing), if:
- there is an OFF1 fault response. The system is only enabled if the fault is removed and was acknowledged and
the "switching on inhibited" withdrawn with OFF1 = 0.
Bit 17 = 1 (enable signal missing), if:
- commissioning mode is selected (p0010 > 0).
- there is an OFF2 fault response.
- the drive is not operational.
Bit 18 = 1 (enable signal missing), if:
- OFF3 has still not been completed or an OFF3 fault response is present.
Bit 19 = 1 (internal pulse enable missing), if:
- sequence control does not have a finished message.
Bit 20 = 1 (internal DC brake active), if:
- the drive is not in the state "Operation" or in "OFF1/3".
- the internal pulse enable is missing (r0046.19 = 0).
Bit 21 = 1 (enable signal missing), if:
- the power unit does not issue an enable signal (e.g. because DC link voltage is too low).
- the holding brake opening time (p1216) has still not expired.
- hibernation is active.
Bit 26 = 1 (enable signal missing), if:
- the drive is not operational.
Bit 27 = 1 (enable signal missing), if:
- de-magnetization not completed.
Bit 28 = 1 (enable signal missing), if:
- the holding brake is closed or has still not been opened.
Bit 30 = 1 (speed controller inhibited), if one of the following reasons is present:
- the pole position identification is active.
- motor data identification is active (only certain steps).
Bit 31 = 1 (enable signal missing), if:
- the speed setpoint from jog 1 or 2 is entered.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-29
Parameters
List of Parameters
r0047
Motor data ident. routine and speed controller optimization / MotID and n_opt
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
300
Factory setting
-
Description:
Displays the actual status for the motor data identification (stationary measurement) and the speed/velocity controller optimization (rotating measurement).
Value:
0:
115:
120:
140:
150:
170:
195:
200:
220:
230:
240:
250:
270:
290:
300:
Note:
Re r0047 = 300:
No measurement
Measurement q leakage inductance (part 2)
Speed controller optimization (vibration test)
Calculate speed controller setting
Measurement, moment of inertia
Measurement, magnetizing current and saturation characteristic
Measurement q leakage inductance (part 1)
Rotating measurement selected
identification, leakage inductance
Identification, rotor time constant
Identification, stator inductance
Identification, stator inductance LQLD
Identification, stator resistance
Identification, valve lockout time
Stationary measurement selected
This value is also displayed if encoder calibration p1990 is selected.
r0050.0...1
CO/BO: Command Data Set CDS effective / CDS effective
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the effective Command Data Set (CDS).
Bit field:
Bit
00
01
Dependency:
Refer to: p0810, p0811, r0836
Note:
The Command Data Set selected using a binector input (e.g. p0810) is displayed using r0836.
r0051.0...1
CO/BO: Drive Data Set DDS effective / DDS effective
Signal name
CDS eff., bit 0
CDS eff., bit 1
1 signal
ON
ON
0 signal
OFF
OFF
Access level: 2
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
FP
-
Factory setting
-
Description:
Displays the effective Drive Data Set (DDS).
Bit field:
Bit
00
01
Dependency:
Refer to: p0820, p0821, r0837
Note:
When selecting the motor data identification routine and the rotating measurement, the drive data set changeover is
suppressed.
1-30
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Signal name
DDS eff., bit 0
DDS eff., bit 1
1 signal
ON
ON
0 signal
OFF
OFF
FP
-
Parameters
List of Parameters
r0052.0...15
CO/BO: Status word 1 / ZSW 1
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays status word 1.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Signal name
Rdy for switch on
Ready
Operation enabled
Fault present
Coast down active (OFF2)
Quick Stop active (OFF3)
Switching on inhibited active
Alarm present
Deviation, setpoint/actual speed
Control request
Maximum speed reached
I, M, P limit reached
Motor holding brake open
Alarm motor overtemperature
Motor rotates forwards
Alarm drive converter overload
Factory setting
1 signal
Yes
Yes
Yes
Yes
No
No
Yes
Yes
No
Yes
Yes
No
Yes
No
Yes
No
0 signal
No
No
No
No
Yes
Yes
No
No
Yes
No
No
Yes
No
Yes
No
Yes
Caution:
p2080 is used to define the signal sources of the PROFIdrive status word interconnection.
Note:
The following status bits are displayed in r0052.
FP
-
Bit 00: r0899 Bit 0
Bit 01: r0899 Bit 1
Bit 02: r0899 Bit 2
Bit 03: r2139 Bit 3 (or r1214 Bit 10, if p1210 > 0)
Bit 04: r0899 Bit 4
Bit 05: r0899 Bit 5
Bit 06: r0899 Bit 6
Bit 07: r2139 Bit 7
Bit 08: r2197 Bit 7
Bit 09: r0899 Bit 7
Bit 10: r2197 Bit 6
Bit 11: r0056 Bit 13 (negated)
Bit 12: r0899 Bit 12
Bit 13: r2135 Bit 14 (negated)
Bit 14: r2197 Bit 3
Bit 15: r2135 Bit 15 (negated)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-31
Parameters
List of Parameters
r0053.0...11
CO/BO: Status word 2 / ZSW 2
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays status word 2.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
Signal name
DC braking active
|n_act| > p1226 (n_standstill)
|n_act| > p1080 (n_min)
I_act >= p2170
|n_act| > p2155
|n_act| <= p2155
|n_act| >= r1119 (n_set)
Vdc <= p2172
Vdc > p2172
Ramp-up/ramp-down completed
Technology controller output at the lower
limit
Technology controller output at the upper
limit
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
FP
-
Yes
No
-
Caution:
p2081 is used to define the signal sources of the PROFIdrive status word interconnection.
Note:
The following status bits are displayed in r0053:
Bit 00: r1239 Bit 8
Bit 01: r2197 Bit 5 (negated)
Bit 02: r2197 Bit 0 (negated)
Bit 03: r2197 Bit 8
Bit 04: r2197 Bit 2
Bit 05: r2197 Bit 1
Bit 06: r2197 Bit 4
Bit 07: r2197 Bit 9
Bit 08: r2197 Bit 10
Bit 09: r1199 Bit 2 (negated)
Bit 10: r2349 Bit 10
Bit 11: r2349 Bit 11
1-32
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0054.0...15
CO/BO: Control word 1 / STW 1
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays control word 1.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
13
14
15
Note:
The following control bits are displayed in r0054:
Signal name
ON/OFF1
OC / OFF2
OC / OFF3
Operation enable
Ramp-function generator enable
Continue ramp-function generator
Speed setpoint enable
Acknowledge fault
Jog bit 0
Jog bit 1
Master ctrl by PLC
Direction reversal (setpoint)
Motorized potentiometer raise
Motorized potentiometer lower
CDS bit 0
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
FP
3030
3030
-
Bit 00: r0898 Bit 0
Bit 01: r0898 Bit 1
Bit 02: r0898 Bit 2
Bit 03: r0898 Bit 3
Bit 04: r0898 Bit 4
Bit 05: r0898 Bit 5
Bit 06: r0898 Bit 6
Bit 07: r2138 Bit 7
Bit 08: r0898 Bit 8
Bit 09: r0898 Bit 9
Bit 10: r0898 Bit 10
Bit 11: r1198 Bit 11
Bit 13: r1198 Bit 13
Bit 14: r1198 Bit 14
Bit 15: r0836 Bit 0
Re bit 10:
If p0700 = 2 is set, bit 10 always shows "1".
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-33
Parameters
List of Parameters
r0055.0...15
CO/BO: Supplementary control word / Suppl STW
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays supplementary control word.
Bit field:
Bit
00
01
02
03
04
05
08
09
11
12
13
15
Note:
The following control bits are displayed in r0055:
Signal name
Fixed setp bit 0
Fixed setp bit 1
Fixed setp bit 2
Fixed setp bit 3
DDS select. bit 0
DDS select. bit 1
Technology controller enable
DC braking enable
Droop enable
Torque control active
External fault 1 (F07860)
CDS bit 1
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
Yes
No
FP
-
Bit 00: r1198 Bit 0
Bit 01: r1198 Bit 1
Bit 02: r1198 Bit 2
Bit 03: r1198 Bit 3
Bit 04: r0837 Bit 0
Bit 05: r0837 Bit 1
Bit 08: r2349 Bit 0 (negated)
Bit 09: r1239 Bit 11
Bit 11: r1406 Bit 11
Bit 12: r1406 Bit 12
Bit 13: r2138 Bit 13
Bit 15: r0836 Bit 1
1-34
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0056.0...15
CO/BO: Status word, closed-loop control / ZSW cl-loop ctrl
PM230
Access level: 3
Calculated: -
Data type: Unsigned16
PM240
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status word of the closed-loop control.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Active
Active
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
Inactive
Inactive
No
No
No
No
No
No
FP
6300
6300
6714
6310
-
13
14
Signal name
Initialization completed
De-magnetizing completed
Pulse enable present
Soft starting present
Magnetizing completed
Voltage boost when starting
Acceleration voltage
Frequency negative
Field weakening active
Voltage limit active
Slip limit active
Frequency limit active
Current limiting controller voltage output
active
Current/torque limiting
Vdc_max controller active
Active
Yes
Inactive
No
15
Vdc_min controller active
Yes
No
6060
6220,
6320
6220,
6320
r0056.0...13
CO/BO: Status word, closed-loop control / ZSW cl-loop ctrl
PM250
Access level: 3
Calculated: -
Data type: Unsigned16
PM260
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status word of the closed-loop control.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
Signal name
Initialization completed
De-magnetizing completed
Pulse enable present
Soft starting present
Magnetizing completed
Voltage boost when starting
Acceleration voltage
Frequency negative
Field weakening active
Voltage limit active
Slip limit active
Frequency limit active
Current limiting controller voltage output
active
Current/torque limiting
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Active
Active
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
Inactive
Inactive
No
No
No
No
No
No
FP
6300
6300
6714
6310
-
Active
Inactive
6060
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-35
Parameters
List of Parameters
r0060
CO: Speed setpoint before the setpoint filter / n_set before filt.
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the actual speed setpoint at the input of the speed controller or U/f characteristic (after the interpolator).
Dependency:
Refer to: r0020
Note:
The speed setpoint is available smoothed (r0020) and unsmoothed (r0060).
r0062
CO: Speed setpoint after the filter / n_set after filter
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the actual speed setpoint after the setpoint filters.
r0063[0...2]
CO: Speed actual value / n_act
Factory setting
- [rpm]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the actual speed of the closed-loop speed control and the U/f control.
Index:
[0] = Unsmoothed
[1] = Smoothed with p0045
[2] = Calculated from f_set - f_slip
Dependency:
Refer to: r0021, r0022
Note:
The speed actual value r0063[0] is additionally displayed - smoothed with p0045 - in r0063[1].
The speed (r0063[2]) calculated from the output frequency and slip can only be compared with the speed actual
value (r0063[0]) in the steady-state.
r0064
CO: Speed controller system deviation / n_ctrl system dev
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the actual system deviation of the speed controller.
r0065
Slip frequency / f_Slip
Description:
1-36
Factory setting
- [rpm]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 2_1
Unit selection: p0505
Min
- [Hz]
Max
- [Hz]
Factory setting
- [Hz]
Displays the slip frequency for induction motors (ASM).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0066
CO: Output frequency / f_outp
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 2_1
Unit selection: p0505
Min
- [Hz]
Max
- [Hz]
Factory setting
- [Hz]
Description:
Displays the output frequency of the power unit.
Dependency:
Refer to: r0024
Note:
The output frequency is available smoothed (r0024) and unsmoothed (r0066).
r0067
CO: Output current, maximum / I_outp max
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Description:
Displays the maximum output current of the power unit.
Dependency:
The maximum output current is determined by the parameterized current limit and the motor and converter thermal
protection.
Refer to: p0290, p0640
r0068[0...1]
CO: Absolute current actual value / I_act abs val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays actual absolute current.
Index:
[0] = Unsmoothed
[1] = Smoothed with p0045
Dependency:
Refer to: r0027
Notice:
The value is updated with the current controller sampling time.
Note:
Absolute current value = sqrt(Iq^2 + Id^2)
Factory setting
- [Arms]
The absolute value of the current actual value is available smoothed (r0027 with 300 ms, r0068[1] with p0045) and
unsmoothed (r0068[0]).
r0069[0...6]
CO: Phase current actual value / I_phase act value
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_5
Unit selection: p0505
Min
- [A]
Max
- [A]
Description:
Displays the measured actual phase currents as peak value.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
[3] = Phase U offset
[4] = Phase V offset
[5] = Phase W offset
[6] = Total U, V, W
Note:
Factory setting
- [A]
In indices 3 ... 5, the offset currents of the 3 phases, which are added to correct the phase currents, are displayed.
The sum of the 3 corrected phase currents is displayed in index 6.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-37
Parameters
List of Parameters
r0070
CO: Actual DC link voltage / Vdc act val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_2
Unit selection: p0505
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
Displays the measured actual value of the DC link voltage.
Dependency:
Refer to: r0026
Notice:
When measuring a DC link voltage < 200 V, for the Power Module (e.g. PM240) a valid measured value is not supplied. In this case, when an external 24 V power supply is connected, a value of approx. 24 V is displayed in the display parameter.
Note:
The DC link voltage is available smoothed (r0026) and unsmoothed (r0070).
r0071
Maximum output voltage / U_output max
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Displays the maximum output voltage.
Dependency:
The maximum output voltage depends on the actual DC link voltage (r0070) and the maximum modulation depth
(p1803).
Note:
As the (driven) motor load increases, the maximum output voltage drops as a result of the reduction in DC link voltage.
r0072
CO: Output voltage / U_output
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Description:
Displays the actual output voltage of the power unit.
Dependency:
Refer to: r0025
Note:
The output voltage is available smoothed (r0025) and unsmoothed (r0072).
r0073
Maximum modulation depth / Modulat_depth max
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Description:
Displays the maximum modulation depth.
Dependency:
Refer to: p1803
1-38
Factory setting
- [Vrms]
Factory setting
- [%]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0074
CO: Modulat_depth / Modulat_depth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the actual modulation depth.
Dependency:
Refer to: r0028
Note:
For space vector modulation, 100% corresponds to the maximum output voltage without overcontrol.
Values above 100 % indicate an overcontrol condition - values below 100% have no overcontrol.
The phase voltage (phase-to-phase, rms) is calculated as follows:(r0074 x r0070) / (sqrt(2) x 100 %).
The modulation depth is available smoothed (r0028) and unsmoothed (r0074).
r0075
CO: Current setpoint field-generating / Id_set
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the field-generating current setpoint (Id_set).
Note:
This value is irrelevant for the U/f control mode.
r0076
CO: Current actual value field-generating / Id_act
Factory setting
- [Arms]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the field-generating current actual value (Id_act).
Dependency:
Refer to: r0029
Note:
This value is irrelevant for the U/f control mode.
Factory setting
- [Arms]
The field-generating current actual value is available smoothed (r0029) and unsmoothed (r0076).
r0077
CO: Current setpoint torque-generating / Iq_set
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the torque/force generating current setpoint.
Note:
This value is irrelevant for the U/f control mode.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [Arms]
1-39
Parameters
List of Parameters
r0078
CO: Current actual value torque-generating / Iq_act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the torque-generating current actual value (Iq_act).
Dependency:
Refer to: r0030
Note:
This value is irrelevant for the U/f control mode.
Factory setting
- [Arms]
The torque-generating current actual value is available smoothed (r0030 with 300 ms) and unsmoothed (r0078).
r0079
CO: Torque setpoint / M_set total
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Description:
Displays the torque setpoint at the output of the speed controller.
r0080[0...1]
CO: Torque actual value / M_act
Factory setting
- [Nm]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Description:
Displays the actual torque value.
Index:
[0] = Unsmoothed
[1] = Smoothed with p0045
Dependency:
Refer to: r0031
Note:
The torque actual value is available smoothed (r0031 with 100 ms, r0080[1] with p0045) and unsmoothed
(r0080[0]).
r0081
CO: Torque utilization / M_Utilization
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the torque utilization as a percentage.
The torque utilization is obtained from the required smoothed torque referred to the torque limit.
Dependency:
This parameter is only available for vector control. For U/f control r0081 = 0 %.
Refer to: r0033
Note:
The torque utilization is available smoothed (r0033) and unsmoothed (r0081).
The torque utilization is obtained from the required torque referred to the torque limit as follows:
- Positive torque: r0081 = (r0079 / r1538) * 100 %
- Negative torque: r0081 = (-r0079 / -r1539) * 100 %
1-40
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0082[0...2]
CO: Active power actual value / P_act
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: r2004
Data set: -
Units group: 14_5
Unit selection: p0505
Min
- [kW]
Max
- [kW]
Factory setting
- [kW]
Description:
Displays the instantaneous active power.
Index:
[0] = Unsmoothed
[1] = Smoothed with p0045
[2] = Electric power
Dependency:
Refer to: r0032
Note:
The mechanical active power is available smoothed (r0032 with 100 ms, r0082[1] with p0045) and unsmoothed
(r0082[0]).
r0083
CO: Flux setpoint / Flex setp
Description:
r0084[0...1]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the flux setpoint.
CO: Flux actual value / Flux act val
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Description:
Displays the flux actual value.
Index:
[0] = Unsmoothed
[1] = Smoothed
r0087
CO: Actual power factor / Cos phi act
Factory setting
- [%]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the actual active power factor.
r0089[0...2]
Actual phase voltage / U_phase act val
Factory setting
-
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_3
Unit selection: p0505
Min
- [V]
Max
- [V]
Description:
Displays the actual phase voltage.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
Note:
The values are determined from the transistor power-on duration.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [V]
1-41
Parameters
List of Parameters
r0094
CO: Transformation angle / Transformat_angle
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2005
Data set: -
Units group: -
Unit selection: -
Min
- [°]
Max
- [°]
Description:
Displays the transformation angle.
Dependency:
Refer to: r1778
Note:
The transformation angle corresponds to the electrical commutation angle.
p0100
IEC/NEMA mot stds / IEC/NEMA mot stds
Description:
Factory setting
- [°]
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C(1)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
0
Defines whether the motor and drive converter power settings (e.g. rated motor power - p0307) are expressed in
[kW] or [hp].
Depending on the selection, the rated motor frequency (p0310) is either set to 50 Hz or 60 Hz.
For p0100 = 0, 2, the following applies: The power factor (p0308) should be parameterized.
For p0100 = 1, the following applies: The efficiency (p0309) should be parameterized.
Value:
0:
1:
2:
IEC-Motor (50 Hz, SI units)
NEMA motor (60 Hz, US units)
NEMA motor (60 Hz, SI units)
Dependency:
If p0100 is changed, all of the rated motor parameters are reset. Only then are possible unit changeovers made.
The units of all motor parameters are changed that are involved in the selection of IEC or NEMA (e.g. r0206, p0307,
r0333, r0334, p0341, p0344, r1969).
Refer to: r0206, p0210, p0300, p0304, p0305, p0307, p0308, p0309, p0310, p0311, p0314, p0320, p0322, p0323,
p0335, r0337, p1800
Note:
The parameter value is not reset when the factory setting is restored (p0010 = 30, p0970).
p0170
Number of Command Data Sets (CDS) / CDS count
Access level: 2
Calculated: -
Data type: Unsigned8
Can be changed: C(15)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
2
Max
4
Factory setting
2
Description:
Sets the number of Command Data Sets (CDS).
Dependency:
Refer to: p0010, r3996
Notice:
When the data sets are created, short-term communication interruptions may occur.
Note:
It is possible to toggle between command parameters (BICO parameters) using this data set changeover.
p0180
Number of Drive Data Sets (DDS) / DDS count
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: C(15)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
4
Factory setting
1
Description:
Sets the number of Drive Data Sets (DDS).
Dependency:
Refer to: p0010, r3996
Notice:
When the data sets are created, short-term communication interruptions may occur.
1-42
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0197
Bootloader vers / Bootloader vers
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the bootloader version.
Dependency:
Refer to: r0018, r0198
Note:
Example:
Factory setting
-
The value 1010100 should be interpreted as V01.01.01.00.
r0198[0...1]
Description:
BIOS/EEPROM data version / BIOS/EEPROM vers
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the BIOS and EEPROM data version.
r0198[0]: BIOS version
r0198[1]: EEPROM data version
Dependency:
Refer to: r0018, r0197
Note:
Example:
The value 1010100 should be interpreted as V01.01.01.00.
p0199[0...24]
Description:
Drive object name / DO name
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: C
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Factory setting
0
Freely assignable name for a drive object.
In the commissioning software, this name cannot be entered using the expert list, but is specified in the configuration assistant. The object name can be subsequently modified in the Project Navigator using standard Windows
resources.
Note:
The parameter is not influenced by setting the factory setting.
r0200[0...n]
Power unit code number actual / PU code no. act
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: PDS
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the unique code number of the power unit.
Note:
r0200 = 0: No power unit data found
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
-
1-43
Parameters
List of Parameters
p0201[0...n]
Power unit code number / PU code no
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: C(2)
Scaling: -
Data set: PDS
Units group: -
Unit selection: -
Min
0
Max
65535
Factory setting
0
Description:
Sets the actual code number from r0200 to acknowledge the power unit being used.
Note:
The parameter is used to identify when the drive is being commissioned for the first time.
When commissioned for the first time, the code number is automatically transferred from r0200 into p0201.
The power unit commissioning can only be exited (p0201 = r0200), if the actual and acknowledged code numbers
are identical (p0010 = 2).
When the code number is changed, the connection voltage (p0210) is checked and, if necessary, adjusted.
r0203[0...n]
Actual power unit type / PU actual type
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: -
Scaling: -
Data set: PDS
Units group: -
Unit selection: -
Min
2
Max
400
Factory setting
-
Description:
Displays the type of power unit found.
Value:
2:
3:
4:
5:
6:
7:
100:
101:
102:
112:
113:
114:
115:
116:
118:
120:
133:
150:
200:
250:
260:
300:
350:
400:
Note:
For parallel circuit configurations, the parameter index is assigned to a power unit.
1-44
MICROMASTER 440
MICROMASTER 411
MICROMASTER 410
MICROMASTER 436
MICROMASTER 440 PX
MICROMASTER 430
SINAMICS S
SINAMICS S (value)
SINAMICS S (combi)
PM220 (SINAMICS G120)
PM230 (SINAMICS G120)
PM240 (SINAMICS G120)
PM250 (SINAMICS G120)
PM260 (SINAMICS G120)
SINAMICS G120 Px
PM340 (SINAMICS S120)
SINAMICS G120C
SINAMICS G
SINAMICS GM
SINAMICS SM
SINAMICS SM120
SINAMICS GL
SINAMICS SL
SINAMICS DCM
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0204[0...n]
Power unit hardware properties / PU HW property
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: PDS
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the properties supported by the power unit hardware.
Bit field:
Bit
01
07
08
12
14
Signal name
RFI filter available
F3E regenerative feedback into the line supply
Internal Braking Module
Safe Brake Control (SBC) supported
Internal LC output filter
1 signal
Yes
Yes
0 signal
No
No
FP
-
Yes
No
Yes
No
Yes
No
-
p0205
Power unit application / PU application
PM230
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C(1, 2)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
1
Description:
The duty cycles can be overloaded provided that the drive converter is operated with its base load current before
and after the overload. This is based on a load duty cycle of 300 s.
Value:
0:
1:
Dependency:
Refer to: r3996
Notice:
The parameter value is not reset when the factory setting is restored (see p0010 = 30, p0970).
Load duty cycle with high overload for vector drives
Load duty cycle with low overload for vector drives
When the power unit use is changed, short-term communication interruptions may occur.
Note:
When the parameter is changed, all of the motor parameters, the technological application and the control mode
are pre-assigned according to the selected application. The parameter has not influence when calculating the thermal overload.
p0205 can only be changed to the settings that are saved in the power unit EEPROM.
p0205
Power unit application / PU application
PM240
Access level: 1
Calculated: -
Data type: Integer16
PM250, PM260
Can be changed: C(1, 2)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
The duty cycles can be overloaded provided that the drive converter is operated with its base load current before
and after the overload. This is based on a load duty cycle of 300 s.
Value:
0:
1:
Dependency:
Refer to: r3996
Notice:
The parameter value is not reset when the factory setting is restored (see p0010 = 30, p0970).
Load duty cycle with high overload for vector drives
Load duty cycle with low overload for vector drives
When the power unit use is changed, short-term communication interruptions may occur.
Note:
When the parameter is changed, all of the motor parameters, the technological application and the control mode
are pre-assigned according to the selected application. The parameter has not influence when calculating the thermal overload.
p0205 can only be changed to the settings that are saved in the power unit EEPROM.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-45
Parameters
List of Parameters
r0206[0...4]
Description:
Index:
Dependency:
r0207[0...4]
Description:
Index:
Rated power unit power / PU P_rated
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: 14_6
Unit selection: p0100
Min
- [kW]
Max
- [kW]
Displays the rated power unit power for various load duty cycles.
[0] = Rated value
[1] = Load duty cycle with low overload
[2] = Load duty cycle with high overload
[3] = Reserved
[4] = Reserved
IECdrives (p0100 = 0): Units kW
NEMA drives (p0100 = 1): Units hp
Refer to: p0100, p0205
Rated power unit current / PU PI_rated
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Dependency:
Displays the rated power unit power for various load duty cycles.
[0] = Rated value
[1] = Load duty cycle with low overload
[2] = Load duty cycle with high overload
[3] = Reserved
[4] = Reserved
Refer to: p0205
r0208
Rated power unit line supply voltage / PU U_rated
Factory setting
- [Arms]
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Vrms]
Max
- [Vrms]
Description:
Displays the rated line supply voltage of the power unit.
r0208 = 400 : 380 - 480 V +/-10 %
r0208 = 500 : 500 - 600 V +/-10 %
r0208 = 690 : 660 - 690 V +/-10 %
r0209[0...4]
Power unit, maximum current / PU I_max
Factory setting
- [Vrms]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Description:
Displays the maximum output current of the power unit.
Index:
[0] = Catalog
[1] = Load duty cycle with low overload
[2] = Load duty cycle with high overload
[3] = Reserved
[4] = Reserved
Dependency:
Refer to: p0205
1-46
Factory setting
- [kW]
Factory setting
- [Arms]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0210
Drive unit line supply voltage / V_connect
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: C(2), T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1 [V]
Max
63000 [V]
Factory setting
400 [V]
Description:
Sets the drive unit supply voltage (rms value of the phase-to-phase line supply voltage).
Dependency:
Set p1254, p1294 (automatic detection of the Vdc switch-on levels) = 0.
The switch-in thresholds of the Vdc_max controller are then directly determined using p0210.
Warning:
In the case of regenerative power units (PM250, PM260), the regenerative power limit for U/f control current limitation control is calculated as a proportion of the supply voltage p0210. Therefore, p0210 should not be set to a value
higher than the actual line voltage.
Caution:
If the line supply voltage is higher than the entered value, the Vdc controller may be automatically de-activated in
some cases to prevent the motor from accelerating. In this case, an appropriate alarm is output.
Note:
Setting ranges for p0210 as a function of the rated power unit voltage:
U_rated = 230 V:
- p0210 = 200 ... 240 V
U_rated = 400 V:
- p0210 = 380 ... 480 V
U_rated = 500 V:
- p0210 = 500 ... 600 V
U_rated = 690 V:
- p0210 = 660 ... 690 V
The pre-charging switch-in threshold for the DC link voltage (Vdc) is calculated from p0210:
Vdc_pre = p0210 * 0.82 * 1.35
The undervoltage thresholds for the DC link voltage (Vdc) are calculated from p0210 as a function of the rated
power unit voltage:
U_rated = 400 V:
- U_min = p0210 * 0.78 > 360 V
U_rated = 500 V:
- U_min = p0210 * 0.76
U_rated = 690 V:
- U_min = p0210 * 0.74 > 450 V
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-47
Parameters
List of Parameters
p0230
Drive filter type, motor side / Drv filt type mot
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C(1, 2)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
4
Description:
Sets the type of the filter at the motor side.
Value:
0:
1:
2:
3:
4:
Dependency:
The following parameters are influenced using p0230:
Factory setting
0
No filter
Motor reactor
dv/dt filter
Sine-wave filter, Siemens
Sine-wave filter, third-party
p0230 = 1:
--> p0233 (power unit, motor reactor) = filter inductance
p0230 = 3:
--> p0233 (power unit, motor reactor) = filter inductance
--> p0234 (power unit sine-wave filter capacitance) = filter capacitance
--> p0290 (power unit overload response) = inhibit pulse frequency reduction
--> p1082 (maximum speed) = Fmax filter / pole pair number
--> p1800 (pulse frequency) >= nominal pulse frequency of the filter
--> p1802 (modulator modes) = space vector modulation without overcontrol
p0230 = 4:
--> p0290 (power unit overload response) = inhibit pulse frequency reduction
--> p1802 (modulator modes) = space vector modulation without overcontrol
The user must set the following parameters according to the data sheet of the sine-wave filter and also the user
must check whether they are permitted.
--> p0233 (power unit, motor reactor) = filter inductance
--> p0234 (power unit sine-wave filter capacitance) = filter capacitance
--> p1082 (maximum speed) = Fmax filter / pole pair number
--> p1800 (pulse frequency) >= nominal pulse frequency of the filter
Refer to: p0233, p0234, p0290, p1082, p1800, p1802
Note:
If the power unit (e.g. PM260) is equipped with an internal sine-wave filter, the parameter cannot be changed.
if a filter type cannot be selected, then this filter type is not permitted for the Motor Module.
p0230 = 1:
Power units with output reactor are limited to output frequencies of 150 Hz.
p0230 = 3:
Power units with sine-wave filter are limited to output frequencies of 200 Hz.
r0231[0...1]
Power cable length, maximum / Cable length max
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [m]
Max
- [m]
Factory setting
- [m]
Description:
Displays the maximum permissible cable lengths between the drive unit and motor.
Index:
[0] = Unshielded
[1] = Shielded
Note:
The display value is used to provide information for service and maintenance.
1-48
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0233
Power unit motor reactor / PU mot reactor
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: C(2), U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [mH]
Max
1000.000 [mH]
Factory setting
0.000 [mH]
Description:
Enter the inductance of a filter connected at the power unit output.
Dependency:
This parameter is automatically pre-set when you select a filter via p0230 if a SIEMENS filter is defined for the
power unit.
Refer to: p0230
Note:
When exiting the quick commissioning using p3900 = 1, the parameter value is set to the value of the defined SIEMENS filter or to zero. For this reason, the parameter value of a third-party filter only has to be entered outside the
commissioning phase (p0010 = 0) and then the controller calculation (p0340 = 3) is carried out.
The parameter cannot be changed if the power unit (e.g. PM260) is equipped with an internal sine-wave filter.
p0234
Power unit sine-wave filter capacitance / PU sine filter C
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: C(2), U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [µF]
Max
1000.000 [µF]
Factory setting
0.000 [µF]
Description:
Enters the capacitance of a sine-wave filter connected at the power unit output.
Dependency:
This parameter is automatically pre-set when you select a filter via p0230 if a SIEMENS filter is defined for the
power unit.
Refer to: p0230
Note:
The parameter value includes the sum of all of the capacitances of a phase connected in series (phase - ground).
When exiting the quick commissioning using p3900 = 1, the parameter value is set to the value of the defined SIEMENS filter or to zero. For this reason, the parameter value of a third-party filter only has to be entered outside the
commissioning phase (p0010 = 0).
The parameter cannot be changed if the power unit (e.g. PM260) is equipped with an internal sine-wave filter.
r0238
Description:
Internal power unit resistance / PU R internal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Displays the internal resistance of the power unit (IGBT and line resistance).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-49
Parameters
List of Parameters
p0278
DC link voltage undervoltage threshold reduction / Vdc U_under red
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-80 [V]
Max
0 [V]
Factory setting
0 [V]
Description:
Sets the absolute value by which the threshold to initiate the undervoltage fault (F30003) is reduced.
Dependency:
Refer to: p0210, r0296
Refer to: F30003
Notice:
When using a Control Supply Module (CSM) for 24 V supply from the DC link, the minimum continuous DC link voltage may not lie below 430 V. DC link voltages in the range 300 ... 430 V are permissible up to a duration of 1 min.
Note:
The resulting shutdown threshold can be read in r0296 and is dependent on the selected rated voltage (p0210) and
the power unit being used.
p0287[0...1]
Ground fault monitoring thresholds / Gnd flt threshold
For chassis power units, this parameter has no significance.
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [%]
Max
100.0 [%]
Factory setting
[0] 6.0 [%]
[1] 16.0 [%]
Description:
Sets the shutdown thresholds for the ground fault monitoring.
The setting is made as a percentage of the maximum power unit current (r0209).
Index:
[0] = Threshold at which pre-charging starts
[1] = Threshold at which pre-charging stops
Dependency:
Refer to: F30021
r0289
CO: Maximum power unit output current / PU I_outp max
Description:
1-50
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Displays the actual maximum output current of the power unit taking into account derating factors.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0290
Description:
Power unit overload response / PU overld response
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
2
Sets the response to a thermal overload condition of the power unit.
The following quantities can result in a response to thermal overload:
- heat sink temperature (r0037.0)
- chip temperature (r0037.1)
- power unit overload I2T (r0036)
Possible measures to avoid thermal overload:
- reduce the output current limit r0289 and r0067 (for closed-loop speed or torque control) or the output frequency
(for U/f control) indirectly via the output current limit and the intervention of the current limiting controller).
- reduce the pulse frequency.
A reduction, if parameterized, is always realized after an appropriate alarm is output.
Value:
0:
1:
2:
3:
Reduce output current or output frequency
No reduction, shutdown when overload threshold is reached
Reduce I_output or f_output and f_pulse (not using I2t)
Reduce the pulse frequency (not using I2t)
Dependency:
If a sine-wave filter is parameterized as output filter (p0230 = 3, 4), then only responses can be selected without
pulse frequency reduction (p0290 = 0, 1).
If a fault or alarm is present, then r2135.13 or r2135.15 is set.
Refer to: r0036, r0037, p0230, r2135
Refer to: A05000, A05001, A07805
Caution:
If the thermal overload of the power unit is not sufficiently reduced by the actions taken, the drive is always shut
down. This means that the power unit is always protected irrespective of the setting of this parameter.
Note:
The setting p0290 = 0, 2 is only practical if the load decreases with decreasing speed (e.g. for applications with variable torque such as for pumps and fans).
Under overload conditions, the current and torque limit are reduced, and therefore the motor is braked and forbidden speed ranges (e.g. minimum speed p1080 and suppression [skip] speeds p1091 ... p1094) can be passed
through.
For p0290 = 2, 3, the I2t overload detection of the power unit does not influence the responses.
When the motor data identification routine is selected, p0290 cannot be changed.
p0292[0...1]
Power unit temperature alarm threshold / PU T_alrm thresh
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [°C]
Max
25 [°C]
Factory setting
[0] 5 [°C]
[1] 15 [°C]
Description:
Sets the alarm threshold for power unit overtemperatures. The value is set as a difference to the tripping (shutdown) temperature.
Drive:
If this threshold is exceeded, an overload alarm is generated and the system responds as parameterized in p0290.
Infeed:
When the threshold value is exceeded, only an overload alarm is output.
Index:
[0] = Heat sink temperature
[1] = Power semiconductor (chip) temperature
Dependency:
Refer to: r0037, p0290
Refer to: A05000
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-51
Parameters
List of Parameters
p0294
Power unit alarm with I2t overload / PU I2t alrm thresh
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10.0 [%]
Max
100.0 [%]
Description:
Sets the alarm threshold for the I2t power unit overload.
Dependency:
Refer to: r0036, p0290
Factory setting
95.0 [%]
If this threshold is exceeded, an overload alarm is generated and the system responds as parameterized in p0290.
Refer to: A07805
Note:
The I2t fault threshold is 100 %. If this value is exceeded, fault F30005 is output.
p0295
Fan run-on time / Fan run-on time
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [s]
Max
600 [s]
Factory setting
0 [s]
Description:
Sets the fan run-on time after the pulses for the power unit have been canceled.
Note:
- Under certain circumstances, the fan can continue to run for longer than was set (e.g. as a result of the excessively high heat sink temperature).
- For values less than 1 s, a 1 s run on time for the fan is active.
- for a PM230 power unit, sizes D - F the parameter is ineffective.
r0296
DC link voltage undervoltage threshold / Vdc U_lower_thresh
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
If the DC link voltage falls below this threshold, the power unit is shut down due to a DC link undervoltage condition
(F30003).
Dependency:
Refer to: p0278
Refer to: F30003
r0297
DC link voltage overvoltage threshold / Vdc U_upper_thresh
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
If the DC link voltage exceeds the threshold specified here, the drive unit is tripped due to DC link overvoltage.
Dependency:
Refer to: F30002
1-52
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0300[0...n]
Description:
Motor type selection / Mot type sel
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
204
Factory setting
0
Selecting the motor type.
The first digit of the parameter value always defines the general motor type and corresponds to the third-party
motor belonging to a motor list:
1 = Rotating induction motor
2 = Rotating synchronous motor
The type information must be entered to filter motor-specific parameters and to optimize the operating characteristics and behavior. For example, for synchronous motors, power factor (p0308) is neither used nor displayed (in the
BOP/IOP).
Value:
0:
1:
2:
17:
204:
No motor
Induction motor (rotating)
Synchronous motor (rotating, permanent-magnet)
1LA7 standard induction motor
1LE4 synchronous motor
Dependency:
When selecting a motor type from the 1LA7 series, parameters p0335, p0626, p0627, and p0628 of the thermal
motor model are pre-assigned as a function of p0307 and p0311.
Note:
Once the Control Unit has been powered up for the first time or if the factory settings have been defined accordingly, the motor type is pre-configured to induction motor (p0300 = 1).
If a motor type has not been selected (p0300 = 0), then the drive commissioning routine cannot be exited.
p0301[0...n]
Description:
Motor code number selection / Mot code No. sel
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
65535
Factory setting
0
The parameter is used to select a motor from a motor parameter list.
When changing the code number (with the exception to the value 0), all of the motor parameters are pre-assigned
from the internally available parameter lists.
Dependency:
Code numbers can only be selected for motor types that correspond to the motor type selected in p0300.
Refer to: p0300
Note:
The motor code number can only be changed if the matching catalog motor was first selected in p0300.
When selecting a catalog motor (p0300 >= 100), drive commissioning can only be exited if a code number is
selected.
p0304[0...n]
Rated motor voltage / Mot U_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0 [Vrms]
Max
20000 [Vrms]
Factory setting
0 [Vrms]
Description:
Sets the rated motor voltage (rating plate).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
When the parameter value is entered the connection type of the motor (star-delta) must be taken into account.
Once the Control Unit has booted for the first time or if the factory settings have been restored, the parameter is
pre-assigned to match the power unit.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-53
Parameters
List of Parameters
p0305[0...n]
Rated motor current / Mot I_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
Description:
Sets the rated motor current (rating plate).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Notice:
If p0305 is changed during quick commissioning (p0010 = 1), then the maximum current p0640 is pre-assigned
accordingly.
Note:
When the parameter value is entered the connection type of the motor (star-delta) must be taken into account.
Once the Control Unit has booted for the first time or if the factory settings have been restored, the parameter is
pre-assigned to match the power unit.
p0307[0...n]
Rated motor power / Mot P_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: 14_6
Unit selection: p0100
Min
0.00 [kW]
Max
100000.00 [kW]
Description:
Sets the rated motor power (rating plate).
Dependency:
IECdrives (p0100 = 0): Units kW
Factory setting
0.00 [kW]
NEMA drives (p0100 = 1): Units hp
NEMA drives (p0100 = 2): Unit kW
Refer to: p0100
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
Once the Control Unit has booted for the first time or if the factory settings have been restored, the parameter is
pre-assigned to match the power unit.
p0308[0...n]
Rated motor power factor / Mot cos_phi_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000
Max
1.000
Description:
Sets the rated motor power factor (cos phi, rating plate).
Dependency:
This parameter is only available for p0100 = 0, 2.
Factory setting
0.000
For a parameter value of 0.000, the power factor is internally calculated and displayed in r0332.
Refer to: p0100, p0309, r0332
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
Once the Control Unit has booted for the first time or if the factory settings have been restored, the parameter is
pre-assigned to match the power unit.
1-54
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0309[0...n]
Rated motor efficiency / Mot eta_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.0 [%]
Max
99.9 [%]
Description:
Sets the rated motor efficiency (rating plate).
Dependency:
This parameter is only available for NEMA motors (p0100 = 1).
Factory setting
0.0 [%]
For a parameter value of 0.0, the power factor is internally calculated and displayed in r0332.
Refer to: p0100, p0308, r0332
Note:
p0310[0...n]
The parameter is not used for synchronous motors.
Rated motor frequency / Mot f_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
650.00 [Hz]
Factory setting
0.00 [Hz]
Description:
Sets the rated motor frequency (rating plate).
Dependency:
The number of pole pairs (r0313) is automatically re-calculated when the parameter is changed (together with
p0311), if p0314 = 0.
The rated frequency is restricted to values between 1.00 Hz and 650.00 Hz.
Refer to: p0311, r0313, p0314
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Notice:
If p0310 is changed during quick commissioning (p0010 = 1), the maximum speed p1082, which is also associated
with quick commissioning, is pre-assigned accordingly. This is not the case when commissioning the motor (p0010
= 3).
Note:
Once the Control Unit has been booted up for the first time or if the factory settings have been defined accordingly,
the parameter is defined in accordance with the power unit.
p0311[0...n]
Description:
Rated motor speed / Mot n_rated
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.0 [rpm]
Max
210000.0 [rpm]
Factory setting
0.0 [rpm]
Sets the rated motor speed (rating plate).
For p0311 = 0, the rated motor slip of induction motors is internally calculated and displayed in r0330.
It is especially important to correctly enter the rated motor speed for vector control and slip compensation for U/f
control.
Dependency:
If p0311 is changed and for p0314 = 0, the pole pair (r0313) is re-calculated automatically.
Refer to: p0310, r0313, p0314
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Notice:
If p0311 is changed during quick commissioning (p0010 = 1), the maximum speed p1082, which is also associated
with quick commissioning, is pre-assigned accordingly. This is not the case when commissioning the motor (p0010
= 3).
Note:
Once the Control Unit has been booted up for the first time or if the factory settings have been defined accordingly,
the parameter is defined in accordance with the power unit.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-55
Parameters
List of Parameters
r0313[0...n]
Description:
Motor pole pair number, actual (or calculated) / Mot PolePairNo act
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the number of motor pole pairs. The value is used for internal calculations.
r0313 = 1: 2-pole motor
r0313 = 2: 4-pole motor, etc.
Dependency:
For p0314 > 0, the entered value is displayed in r0313.
For p0314 = 0, the pole pair number (r0313) is automatically calculated from the rated power (p0307), rated frequency (p0310) and rated speed (p0311).
Refer to: p0307, p0310, p0311, p0314
Note:
For the automatic calculation, the pole pair number is set to the value of 2 if the rated speed or the rated frequency
is zero.
p0314[0...n]
Motor pole pair number / Mot pole pair No.
Description:
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
255
Factory setting
0
Sets the motor pole pair number.
p0314 = 1: 2-pole motor
r0314 = 2: 4-pole motor, etc.
Dependency:
For p0314 = 0, the pole pair number is automatically calculated from the rated frequency (p0310) and the rated
speed (p0311) and displayed in r0313.
Notice:
If p0314 is changed during quick commissioning (p0010 = 1), the maximum speed p1082, which is also associated
with quick commissioning, is pre-assigned accordingly.
For induction motors, the value need only be input if the rated data of a generator is entered therefore resulting in a
negative rated slip. In this case, the number of pole pairs in r0313 is too low by 1 and must be manually corrected.
p0316[0...n]
Description:
Motor torque constant / Mot kT
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3), U, T
Scaling: -
Data set: MDS
Units group: 28_1
Unit selection: p0100
Min
0.00 [Nm/A]
Max
400.00 [Nm/A]
Factory setting
0.00 [Nm/A]
Sets the torque constant of the synchronous motor.
p0316 = 0: The torque constant is calculated from the motor data.
p0316 > 0: The selected value is used as torque constant.
Dependency:
Refer to: r0334
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
This parameter is not used for induction motors (p0300 = 1xx).
1-56
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0318[0...n]
Motor stall current / Mot I_standstill
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
Description:
Sets the stall current for synchronous motors (p0300 = 2xx).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The parameter is used for the I2t monitoring of the motor (refer to p0611).
This parameter is not used for induction motors (p0300 = 1xx).
p0320[0...n]
Description:
Motor rated magnetizing current/short-circuit current / Mot I_mag_rated
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [Arms]
Max
5000.000 [Arms]
Factory setting
0.000 [Arms]
Induction motors:
Sets the rated motor magnetizing current.
For p0320 = 0.000 the magnetizing current is internally calculated and displayed in r0331.
Synchronous motors:
Sets the rated motor short-circuit current.
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The magnetizing current p0320 for induction motors is reset when quick commissioning is exited with p3900 > 0.
If, for induction motors, the magnetizing current p0320 is changed outside the commissioning phase (p0010 > 0),
then the magnetizing inductance p0360 is changed so that the EMF r0337 remains constant.
p0322[0...n]
Maximum motor speed / Mot n_max
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.0 [rpm]
Max
210000.0 [rpm]
Factory setting
0.0 [rpm]
Description:
Sets the maximum motor speed.
Dependency:
Refer to: p1082
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Notice:
If p0322 is changed during quick commissioning (p0010 = 1), the maximum speed p1082, which is also associated
with quick commissioning, is pre-assigned accordingly.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-57
Parameters
List of Parameters
p0323[0...n]
Maximum motor current / Mot I_max
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3)
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
20000.00 [Arms]
Factory setting
0.00 [Arms]
Description:
Sets the maximum permissible motor current (e.g. de-magnetizing current for synchronous motors).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Notice:
If p0323 is changed during quick commissioning (p0010 = 1), then the maximum current p0640 is pre-assigned
accordingly.
Note:
The parameter has no effect for induction motors.
The parameter has not effect for synchronous motors if a value of 0.0 is entered. The user-selectable current limit is
entered into p0640.
p0325[0...n]
Description:
Motor pole position identification current, 1st phase / Mot PolID I 1st ph
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [Arms]
Max
10000.000 [Arms]
Factory setting
0.000 [Arms]
Sets the current for the 1st phase of the two-stage technique for pole position identification routine.
The current of the 2nd phase is set in p0329.
The two-stage technique is selected with p1980 = 4.
Dependency:
Refer to: p0329, p1980, r1984, r1985, r1987
Notice:
When the motor code (p0301) is changed, it is possible that p0325 is not pre-assigned.
p0325 can be pre-assigned using p0340 = 3.
Note:
The value is automatically pre-assigned for the following events:
- For p0325 = 0 and automatic calculation of the closed-loop control parameters (p0340 = 1, 2, 3).
- for quick commissioning (p3900 = 1, 2, 3).
p0326[0...n]
Motor stall torque correction factor / Mot M_stall_corr
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
5 [%]
Max
300 [%]
Factory setting
100 [%]
Description:
Sets the correction factor for the stall torque/force at a 600 V DC link voltage.
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
1-58
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0327[0...n]
Description:
Optimum motor load angle / Mot phi_load opt
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.0 [°]
Max
135.0 [°]
Factory setting
90.0 [°]
Sets the optimum load angle for synchronous motors with reluctance torque.
The load angle is measured at the rated motor current.
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
This parameter has no significance for induction motors.
For synchronous motors without reluctance torque, a angle of 90 degrees must be set.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0328[0...n]
Description:
Motor reluctance torque constant / Mot kT_reluctance
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
-1000.00 [mH]
Max
1000.00 [mH]
Factory setting
0.00 [mH]
Sets the reluctance torque constant for synchronous motors with reluctance torque (e.g. 1FE ... motors).
This parameter has no significance for induction motors.
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
For synchronous motors without reluctance torque, the value 0 must be set.
p0329[0...n]
Motor pole position identification current / Mot PolID current
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
Sets the current for the pole position identification routine.
For a two-stage technique, the current is set for the 2nd phase.
Dependency:
Refer to: p0325, p1980, r1984, r1985, r1987
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
r0330[0...n]
Rated motor slip / Mot slip_rated
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [Hz]
Max
- [Hz]
Factory setting
- [Hz]
Description:
Displays the rated motor slip.
Dependency:
The rated slip is calculated from the rated frequency, rated speed and number of pole pairs.
Refer to: p0310, p0311, r0313
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-59
Parameters
List of Parameters
r0331[0...n]
Description:
Actual motor magnetizing current/short-circuit current / Mot I_mag_rtd act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Induction motor:
Displays the rated magnetizing current from p0320.
For p0320 = 0, the internally calculated magnetizing current is displayed.
Synchronous motor:
Displays the rated short-circuit current from p0320.
Dependency:
r0332[0...n]
Description:
If p0320 was not entered, then the parameter is calculated from the rating plate parameters.
Rated motor power factor / Mot cos_phi_rated
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the rated power factor for induction motors.
For IEC motors, the following applies (p0100 = 0):
For p0308 = 0, the internally-calculated power factor is displayed.
For p0308 > 0, this value is displayed.
For NEMA motors, the following applies (p0100 = 1):
For p0309 = 0, the internally-calculated power factor is displayed.
For p0309 > 0, this value is converted into the power factor and displayed.
Dependency:
If p0308 is not entered, the parameter is calculated from the rating plate parameters.
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
r0333[0...n]
Rated motor torque / Mot M_rated
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: 7_4
Unit selection: p0100
Min
- [Nm]
Max
- [Nm]
Description:
Displays the rated motor torque.
Dependency:
IEC drives (p0100 = 0): unit Nm
Factory setting
- [Nm]
NEMA drives (p0100 = 1): unit lbf ft
Note:
For induction motors, r0333 is calculated from p0307 and p0311.
For synchronous motors, r0333 is calculated from p0305, p0316, p0327 and p0328.
1-60
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0334[0...n]
Actual motor-torque constant / Mot kT act
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: 28_1
Unit selection: p0100
Min
- [Nm/A]
Max
- [Nm/A]
Description:
Displays the torque constant of the synchronous motor used.
Dependency:
IEC drives (p0100 = 0): unit Nm / A
Factory setting
- [Nm/A]
NEMA drives (p0100 = 1): unit lbf ft / A
Note:
This parameter is not used for induction motors (p0300 = 1xx).
For synchronous motors, parameter r0334 is calculated from p0305, p0307 and p0311.
p0335[0...n]
Motor cooling type / Motor cooling type
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(1, 3), T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
128
Factory setting
0
Description:
Sets the motor cooling system used.
Value:
0:
1:
2:
128:
Dependency:
For 1LA7 motors (refer to p0300), the parameter is pre-set as a function of p0307 and p0311.
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The parameter influences the thermal 3-mass motor model.
Non-ventilated
Forced cooling
Liquid cooling
No fan
1LA7 motors, frame size 56 are operated without fan.
r0337[0...n]
Rated motor EMF / Mot EMF_rated
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [Vrms]
Max
- [Vrms]
Description:
Displays the rated EMF of the motor.
Note:
EMF: Electromagnetic force
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [Vrms]
1-61
Parameters
List of Parameters
p0340[0...n]
Automatic calculation, motor/control parameters / Calc auto par
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(3), T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
5
Factory setting
0
Description:
Setting to automatically calculate motor parameters and U/f open-loop and closed-loop control parameters from the
rating plate data.
Value:
0:
1:
2:
3:
4:
5:
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
No calculation
Complete calculation
Calculation of equivalent circuit diagram parameters
Calculation of closed-loop control parameters
Calculation of controller parameters
Calculation of technological limits and threshold values
The following parameters are influenced using p0340:
p0340 = 1:
--> All of the parameters influenced for p0340 = 2, 3, 4, 5
--> p0341, p0342, p0344, p0612, p0640, p1082, p1231, p1232, p1333, p1349, p1611, p1654, p1726, p1825, p1828
... p1832, p1909, p1959, p2000, p2001, p2002, p2003, p3927, p3928
p0340 = 2:
--> p0350, p0354 ... p0360
--> p0625 (matching p0350)
p0340 = 3:
--> All of the parameters influenced for p0340 = 4, 5
--> p0346, p0347, p0622, p1320 ... p1327, p1582, p1584, p1616, p1755, p1756, p2178
p0340 = 4:
--> p1290, p1292, p1293, p1338, p1339, p1340, p1341, p1345, p1346, p1461, p1463, p1464, p1465, p1470,
p1472, p1703, p1715, p1717, p1740, p1756, p1764, p1767, p1781, p1783, p1785, p1786, p1795
p0340 = 5:
--> p1037, p1038, p1520, p1521, p1530, p1531, p1574, p1802, p1803, p2140, p2142, p2148, p2150, p2161,
p2162, p2163, p2164, p2175, p2177, p2194, p2390, p2392, p2393
Note:
p0340 = 1 contains the calculations of p0340 = 2, 3, 4, 5.
p0340 = 2 calculates the motor parameters (p0350 ... p0360).
p0340 = 3 contains the calculations of p0340 = 4, 5.
p0340 = 4 only calculates the controller parameters.
p0340 = 5 only calculates the controller limits.
When quick commissioning is exited using p3900 > 0, p0340 is automatically set to 1.
At the end of the calculations, p0340 is automatically set to 0.
1-62
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0341[0...n]
Motor moment of inertia / Mot M_mom of inert
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 25_1
Unit selection: p0100
Min
0.000000 [kgm²]
Max
100000.000000 [kgm²]
Description:
Sets the motor moment of inertia (without load).
Dependency:
IEC drives (p0100 = 0): unit kg m^2
Factory setting
0.000000 [kgm²]
NEMA drives (p0100 = 1): unit lb ft^2
The parameter value is included, together with p0342, in the rated starting time of the motor.
Refer to: p0342, r0345
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The product of p0341 * p0342 is used when the speed controller (p0340 = 4) is calculated automatically.
p0342[0...n]
Ratio between the total and motor moment of inertia / Mot MomInert Ratio
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
1.000
Max
10000.000
Factory setting
1.000
Description:
Sets the ratio between the total moment of inertia/mass (load + motor) and the intrinsic motor moment of inertia/mass (no load).
Dependency:
This means that together with p0341, the rated starting (accelerating time) of the motor is calculated for a vector
drive.
Refer to: p0341, r0345
Note:
r0343[0...n]
Description:
p0344[0...n]
The product of p0341 * p0342 is used when the speed controller (p0340 = 4) is calculated automatically.
Rated motor current identified / Mot I_rated ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
- [Arms]
Displays the identified rated motor current.
Motor weight (for the thermal motor model) / Mot weight th mod
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: C(3), T
Scaling: -
Data set: MDS
Units group: 27_1
Unit selection: p0100
Min
0.0 [kg]
Max
50000.0 [kg]
Description:
Sets the motor weight.
Dependency:
IEC drives (p0100 = 0): unit kg
Factory setting
0.0 [kg]
NEMA drives (p0100 = 1): unit lb
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The parameter influences the thermal 3 mass model of the induction motor.
The parameter is not used for synchronous motors (p0300 = 2xx).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-63
Parameters
List of Parameters
r0345[0...n]
Nominal motor starting time / Mot t_start_rated
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [s]
Max
- [s]
Factory setting
- [s]
Description:
Displays the rated motor starting time. This time corresponds to the time from standstill up to reaching the motor
rated speed and the acceleration with motor rated torque (r0333).
Dependency:
Refer to: r0313, r0333, p0341, p0342
p0346[0...n]
Motor excitation build-up time / Mot t_excitation
Description:
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [s]
Max
20.000 [s]
Factory setting
0.000 [s]
Sets the excitation build-up time of the motor.
This involves the delay time between enabling the pulses and enabling the ramp-function generator. The induction
motor is magnetized during this time.
Caution:
If there is insufficient magnetization under load or if the acceleration rate is too high, then an induction motor can
stall (refer to the note).
Note:
The parameter is calculated using p0340 = 1, 3.
For induction motors, the result depends on the rotor time constant (r0384). If this time is excessively reduced, this
can result in an inadequate magnetizing of the induction motor. This is the case if the current limit is reached while
building up magnetizing. For induction motors, the parameter cannot be set to 0 s (internal limit: 0.1 * r0384).
For permanent-magnet synchronous motors and vector control, the value depends on the stator time constant
(r0386). Here, it defines the time to establish the current for encoderless operation immediately after the pulses
have been enabled.
p0347[0...n]
Description:
Motor de-excitation time / Mot t_de-excitat.
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [s]
Max
20.000 [s]
Factory setting
0.000 [s]
Sets the de-magnetizing time (for induction motors) after the inverter pulses have been canceled.
The inverter pulses cannot be switched in (enabled) within this delay time.
Note:
The parameter is calculated using p0340 = 1, 3.
For induction motors, the result depends on the rotor time constant (r0384).
if this time is shortened too much, then this can result in an inadequate de-magnetizing of the induction motor and
in an overcurrent condition when the pulses are subsequently enabled (only when the flying restart function is activated and the motor is rotating).
1-64
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0350[0...n]
Motor stator resistance, cold / Mot R_stator cold
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [ohm]
Max
2000.00000 [ohm]
Factory setting
0.00000 [ohm]
Description:
Sets the stator resistance of the motor at ambient temperature p0625.
Dependency:
Refer to: p0625, r1912
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The motor identification routine determines the stator resistance from the total stator resistance minus the cable
resistance (p0352).
p0352[0...n]
Cable resistance / Mot R_cable cold
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [ohm]
Max
120.00000 [ohm]
Factory setting
0.00000 [ohm]
Description:
Resistance of the power cable between the power unit and motor.
Caution:
The cable resistance should be entered prior to motor data identification. If it is used subsequently, the difference
by which p0352 was changed must be subtracted from the stator resistance p0350 or motor data identification must
be repeated.
Note:
The parameter influences the temperature adaptation of the stator resistance.
The motor identification sets the cable resistance to 20% of the measured total resistance if p0352 is zero at the
time that the measurement is made. If p0352 is not zero, then the value is subtracted from the measured total stator
resistance to calculate stator resistance p0350. In this case, p0350 is a minimum of 10% of the measured value.
The cable resistance is reset when quick commissioning is exited with p3900 > 0.
p0354[0...n]
Description:
Motor rotor resistance cold / Mot R_r cold
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [ohm]
Max
300.00000 [ohm]
Factory setting
0.00000 [ohm]
Sets the rotor/secondary section resistance of the motor at the ambient temperature p0625.
This parameter value is automatically calculated using the motor model (p0340 = 1, 2) or using the motor data identification routine (p1910).
Dependency:
Refer to: p0625
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The parameter is not used for synchronous motors (p0300 = 2).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-65
Parameters
List of Parameters
p0356[0...n]
Description:
Motor stator leakage inductance / Mot L_stator leak.
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [mH]
Max
1000.00000 [mH]
Factory setting
0.00000 [mH]
Induction machine: sets the stator leakage inductance of the motor.
Synchronous motor: Sets the stator quadrature axis inductance of the motor.
This parameter value is automatically calculated using the motor model (p0340 = 1, 2) or using the motor identification routine (p1910).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
If the stator leakage inductance (p0356) for induction motors is changed outside the commissioning phase (p0010 >
0), the magnetizing inductance (p0360) is automatically adapted to the new EMF (r0337). You are then advised to
repeat the measurement for the saturation characteristic (p1960).
For permanent-magnet synchronous motors (p0300 = 2), this is the non-saturated value and is, therefore, ideal for
a low current.
p0357[0...n]
Description:
Motor stator inductance, d axis / Mot L_stator d
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [mH]
Max
1000.00000 [mH]
Factory setting
0.00000 [mH]
Sets the stator direct-axis inductance of the synchronous motor.
This parameter value is automatically calculated using the motor model (p0340 = 1, 2) or using the motor identification routine (p1910).
Note:
p0358[0...n]
Description:
For permanent-magnet synchronous motors (p0300 = 2), this is the non-saturated value and is ideal for a low current.
Motor rotor leakage inductance / Mot L_rot leak
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [mH]
Max
1000.00000 [mH]
Factory setting
0.00000 [mH]
Sets the rotor/secondary section leakage inductance of the motor.
The value is automatically calculated using the motor model (p0340 = 1, 2) or using the motor identification routine
(p1910).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
If the rotor leakage inductance (p0358) for induction motors is changed outside the commissioning phase (p0010 >
0), then the magnetizing inductance (p0360) is automatically adapted to the new EMF (r0337). You are then
advised to repeat the measurement for the saturation characteristic (p1960).
1-66
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0360[0...n]
Description:
Motor magnetizing inductance / Mot Lh
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00000 [mH]
Max
10000.00000 [mH]
Factory setting
0.00000 [mH]
Sets the magnetizing inductance of the motor.
This parameter value is automatically calculated using the motor model (p0340 = 1, 2) or using the motor identification routine (p1910).
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The parameter is not used for synchronous motors (p0300 = 2).
p0362[0...n]
Description:
Motor saturation characteristic flux 1 / Mot saturat.flux 1
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
10.0 [%]
Max
300.0 [%]
Factory setting
60.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the y coordinate (flux) for the 1st value pair of the characteristic.
Sets the first flux value of the saturation characteristic as a [%] referred to the rated motor flux (100 %).
Dependency:
The following applies for the flux values:
p0362 < p0363 < p0364 < p0365
Refer to: p0366
Note:
For induction motors, p0362 = 100 % corresponds to the rated motor flux.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0363[0...n]
Description:
Motor saturation characteristic flux 2 / Mot saturat.flux 2
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
10.0 [%]
Max
300.0 [%]
Factory setting
85.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the y coordinate (flux) for the 2nd value pair of the characteristic.
Sets the second flux value of the saturation characteristic as a [%] referred to the rated motor flux (100 %).
Dependency:
The following applies for the flux values:
p0362 < p0363 < p0364 < p0365
Refer to: p0367
Note:
For induction motors, p0363 = 100 % corresponds to the rated motor flux.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-67
Parameters
List of Parameters
p0364[0...n]
Description:
Motor saturation characteristic flux 3 / Mot saturat.flux 3
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
10.0 [%]
Max
300.0 [%]
Factory setting
115.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the y coordinate (flux) for the 3rd value pair of the characteristic.
Sets the third flux value of the saturation characteristic as a [%] referred to the rated motor flux (100 %).
Dependency:
The following applies for the flux values:
p0362 < p0363 < p0364 < p0365
Refer to: p0368
Note:
For induction motors, p0364 = 100 % corresponds to the rated motor flux.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0365[0...n]
Description:
Motor saturation characteristic flux 4 / Mot saturat.flux 4
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
10.0 [%]
Max
300.0 [%]
Factory setting
125.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the y coordinate (flux) for the 4th value pair of the characteristic.
Sets the fourth flux value of the saturation characteristic as a [%] referred to the rated motor flux (100 %).
Dependency:
The following applies for the flux values:
p0362 < p0363 < p0364 < p0365
Refer to: p0369
Note:
For induction motors, p0365 = 100 % corresponds to the rated motor flux.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0366[0...n]
Description:
Motor saturation characteristic I_mag 1 / Mot sat. I_mag 1
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
5.0 [%]
Max
800.0 [%]
Factory setting
50.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the x coordinate (magnetizing current) for the 1st value pair of the characteristic.
Sets the first magnetization current of the saturation characteristic in [%] with reference to the rated magnetization
current (r0331).
Dependency:
The following applies for the magnetizing currents:
p0366 < p0367 < p0368 < p0369
Refer to: p0362
Note:
1-68
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0367[0...n]
Description:
Motor saturation characteristic I_mag 2 / Mot sat. I_mag 2
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
5.0 [%]
Max
800.0 [%]
Factory setting
75.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the x coordinate (magnetizing current) for the 2nd value pair of the characteristic.
Sets the second magnetization current of the saturation characteristic in [%] with reference to the rated magnetization current (r0331).
Dependency:
The following applies for the magnetizing currents:
p0366 < p0367 < p0368 < p0369
Refer to: p0363
Note:
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0368[0...n]
Motor saturation characteristic I_mag 3 / Mot sat. I_mag 3
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
5.0 [%]
Max
800.0 [%]
Factory setting
150.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the x coordinate (magnetizing current) for the 3rd value pair of the characteristic.
Sets the third magnetization current of the saturation characteristic in [%] with reference to the rated magnetization
current (r0331).
Dependency:
The following applies for the magnetizing currents:
p0366 < p0367 < p0368 < p0369
Refer to: p0364
Note:
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0369[0...n]
Motor saturation characteristic I_mag 4 / Mot sat. I_mag 4
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
5.0 [%]
Max
800.0 [%]
Factory setting
210.0 [%]
The saturation characteristics (flux as a function of the magnetizing current) is defined using 4 points.
This parameter specifies the x coordinate (magnetizing current) for the 4th value pair of the characteristic.
Sets the fourth magnetization current of the saturation characteristic in [%] with reference to the rated magnetization current (r0331).
Dependency:
The following applies for the magnetizing currents:
p0366 < p0367 < p0368 < p0369
Refer to: p0365
Note:
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-69
Parameters
List of Parameters
r0370[0...n]
Description:
Motor stator resistance, cold / Mot R_stator cold
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Displays the motor stator resistance at an ambient temperature (p0625).
The value does not include the cable resistance.
Dependency:
r0372[0...n]
Refer to: p0625
Cable resistance / Mot R_cable
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Description:
Displays the total cable resistance between power unit and motor, as well as the internal converter resistance.
Dependency:
Refer to: r0238, p0352
r0373[0...n]
Motor rated stator resistance / Mot R_stator rated
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Description:
Displays the rated motor stator resistance at rated temperature (total of p0625 and p0627).
Dependency:
Refer to: p0627
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
r0374[0...n]
Motor rotor resistance cold / Mot R_r cold
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Description:
Displays the motor rotor resistance at an ambient temperature p0625.
Dependency:
Refer to: p0625
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
r0376[0...n]
Factory setting
- [ohm]
Rated motor rotor resistance / Mot R_rotor rated
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Description:
Displays the rated motor rotor resistance at rated temperature (total of p0625 and p0628).
Dependency:
Refer to: p0628
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
1-70
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0377[0...n]
Description:
r0378[0...n]
Motor leakage inductance, total / Mot L_leak total
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Displays the stator leakage inductance of the motor including the motor reactor (p0233).
Motor stator inductance, d axis / Mot L_stator_d
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the stator longitudinal inductance of the synchronous motor including the motor reactor (p0233).
r0382[0...n]
Motor magnetizing inductance transformed / Mot L_magn transf
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the magnetizing inductance of the motor.
Note:
The parameter is not used for synchronous motors (p0300 = 2xx).
r0384[0...n]
Motor rotor time constant / damping time constant d axis / Mot T_rotor/T_Dd
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Description:
Displays the rotor time constant.
Note:
The parameter is not used for synchronous motors.
Factory setting
- [ms]
The value is calculated from the total of the inductances on the rotor side (p0358, p0360) divided by the rotor resistance (p0354). The temperature adaptation of the rotor resistance for induction motors is not taken into account.
r0386[0...n]
Motor stator leakage time constant / Mot T_stator leak
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Factory setting
- [ms]
Description:
Displays the stator leakage time constant.
Note:
The value is calculated from the total of all leakage inductances (p0233, p0356, p0358) divided by the total of all
motor resistances (p0350, p0352, p0354). The temperature adaptation of the resistances is not taken into account.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-71
Parameters
List of Parameters
r0395[0...n]
Actual stator resistance / R_stator act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Description:
Displays the actual stator resistance (phase value).
Dependency:
In the case of induction motors the parameter is also affected by the motor temperature model.
The parameter value also contains the temperature-independent cable resistance.
Refer to: p0350, p0352, p0620
Note:
In each case, only the stator resistance of the active Motor Data Set is included with the stator temperature of the
thermal motor model.
r0396[0...n]
Actual rotor resistance / R_rotor act
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Displays the actual rotor resistance (phase value).
The parameter is affected by the motor temperature model.
Dependency:
Refer to: p0354, p0620
Note:
In each case, only the rotor resistance of the active Motor Data Set is included with the rotor temperature of the
thermal motor model.
This parameter is not used for synchronous motors (p0300 = 2xx).
p0490
Meas. probe invert / Probe inv
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
0000 bin
Description:
Setting to invert the digital input signals to connect a measuring probe.
Bit field:
Bit
03
Dependency:
Refer to: p0580
Note:
When the measuring probe is inverted, this has no effect on the status displays of the digital inputs (r0721, r0722,
r0723).
1-72
Signal name
DI 3 (T. 8)
1 signal
Inverted
0 signal
Not inverted
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0500
Technology application / Tec application
PM230
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: C(1, 5), T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
3
Max
3
Description:
Factory setting
3
Sets the technology application.
The parameter influences the calculation of open-loop and closed-loop control parameters that is e.g. initiated using
p0340 = 5.
Value:
3:
Notice:
If the technological application is set to p0500 = 0 ... 3 during commissioning (p0010 = 1, 5, 30), the operating mode
(p1300) is pre-set accordingly.
Pumps and fans, efficiency optimization
Note:
The calculation of parameters dependent on the technology application can be called up as follows:
- when exiting quick commissioning using p3900 > 0
- when writing p0340 = 1, 3, 5
For p0500 = 3 and when the calculation is initiated, the following parameters are set:
- p1574 = 2 V
- p1750 bit 2 = 1: Sensorless closed-loop control of induction motors effective up to a frequency of zero.
- p1802 = 10 (SVM/FLB with overmodulation and modulation depth reduction over 57 Hz)
- p1803 = 115 %
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-73
Parameters
List of Parameters
p0500
Technology application / Tec application
PM240
Access level: 2
Calculated: -
Data type: Integer16
PM250, PM260
Can be changed: C(1, 5), T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Description:
Factory setting
0
Sets the technology application.
The parameter influences the calculation of open-loop and closed-loop control parameters that is e.g. initiated using
p0340 = 5.
Value:
0:
1:
2:
3:
Standard drive
Pumps and fans
Sensorless closed-loop control down to f = 0 (passive loads)
Pumps and fans, efficiency optimization
Notice:
If the technological application is set to p0500 = 0 ... 3 during commissioning (p0010 = 1, 5, 30), the operating mode
(p1300) is pre-set accordingly.
Note:
The calculation of parameters dependent on the technology application can be called up as follows:
- when exiting quick commissioning using p3900 > 0
- when writing p0340 = 1, 3, 5
For p0500 = 0 and when the calculation is initiated, the following parameters are set:
- p1574 = 10 V
- p1750 bit 2 = 0
- p1802 = 4 (SVM/FLB without overcontrol) (PM240: p1802 = 0, PM260: p1802 = 2)
- p1803 = 106 % (PM260: p1803 = 103 %)
For p0500 = 1 and when the calculation is initiated, the following parameters are set:
- p1574 = 2 V
- p1750 bit 2 = 0
- p1802 = 4 (SVM/FLB without overcontrol) (PM240: p1802 = 0)
- p1803 = 106 % (PM260: p1803 = 103 %)
For p0500 = 2 and when the calculation is initiated, the following parameters are set:
- p1574 = 2 V (for separately-excited synchronous motors: 4 V)
- p1750 bit 2 = 1
- p1802 = 4 (SVM/FLB without overcontrol) (PM240: p1802 = 0)
- p1803 = 106 % (PM260: p1803 = 103 %)
For p0500 = 3 and when the calculation is initiated, the following parameters are set:
- p1574 = 2 V
- p1750 bit 2 = 1
- p1802 = 4 (SVM/FLB without overcontrol) (PM240: p1802 = 0)
- p1803 = 106 % (PM260: p1803 = 103 %)
Re p1750:
The setting of p1750 is only relevant for induction motors.
p1750 bit 2 = 1: Sensorless closed-loop control of induction motors effective up to a frequency of zero.
This operating mode is possible for passive loads. These include applications where the load does not generate
regenerative torque when breaking away and the motor comes to a standstill (zero speed) itself when the pulses
are inhibited.
Re p1802 / p1803:
p1802 and p1803 are only changed, in all cases, if a sine-wave output filter (p0230 = 3, 4) has not been selected.
1-74
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0505
Selecting the system of units / Unit sys select
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C(5)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
4
Factory setting
1
Description:
Adjustable parameter of the actual system of units.
Value:
1:
2:
3:
4:
Dependency:
The parameter cannot be changed if the master control was fetched.
Caution:
If a per unit representation is selected and if the reference parameters (e.g. p2000) are subsequently changed, then
the physical significance of several control parameters is also adapted at the same time. As a consequence, the
control behavior can change (see p1576, p1621, p1744, p1752, p1755 and p1609, p1612, p1619, p1620).
Note:
Reference parameter for the unit system % are, for example, p2000 ... p2004. Depending on what has been
selected, these are displayed using either SI or US units.
p0573
Inhibit automatic reference value calculation / Inhibit calc
SI system of units
System of units, referred/SI
US system of units
System of units, referred/US
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Setting to inhibit the calculation of reference parameters (e.g. p2000) when automatically calculating the motor and
closed-loop control parameters (p0340, p3900).
Value:
0:
1:
Notice:
The inhibit for the reference value calculation is canceled when new motor parameters (e.g. p0305) are entered and
only one drive data set exists (p0180 = 1). This is the case during initial commissioning.
No
Yes
Once the motor and control parameters have been calculated (p0340, p3900), the inhibit for the reference value
calculation is automatically re-activated.
Note:
If value = 0:
The automatic calculation (p0340, p3900) overwrites the reference parameters.
If value = 1:
The automatic calculation (p0340, p3900) does not overwrite the reference parameters.
p0580
Measuring probe, input terminal / MT input terminal
CU240E-2
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
23
CU240E-2 F
Factory setting
0
Description:
Sets the input terminal for the measuring probe for speed actual value measurement.
Value:
0:
23:
Dependency:
Refer to: p0581
Note:
DI: Digital Input
No measuring probe
DI 3 (T. 8)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-75
Parameters
List of Parameters
p0581
Measuring probe, edge / MT edge
CU240E-2
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
1
CU240E-2 F
Description:
Factory setting
0
Sets the edge to evaluate the measuring probe signal for speed actual value measurement.
0: 0/1 edge
1: 1/0 edge
Dependency:
Refer to: p0580
p0582
Measuring probe, pulses per revolution / MT pulses per rev
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
1
Max
12
CU240E-2 F
Factory setting
1
Description:
Sets the number of pulses per revolution (e.g. for disks with holes).
p0583
Measuring probe, maximum measuring time / MT t_meas max
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.040 [s]
Max
10.000 [s]
CU240E-2 F
Description:
Factory setting
10.000 [s]
Sets the maximum measuring time for the measuring probe.
If a new pulse is not received before the maximum measuring time has expired, then the speed actual value in
r0586 is set to zero. This timer is re-started with the next pulse.
Dependency:
Refer to: r0586
p0585
Measuring probe gear factor / Probe gear factor
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.00000
Max
1000.00000
CU240E-2 F
Description:
Factory setting
1.00000
Sets the BERO gear factor.
The measured speed is multiplied by the BERO gear factor and is displayed in r0586.
1-76
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0586
CO: Measuring probe, speed actual value / MT n_act
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: -
Scaling: p2000
Data set: -
CU240E-2 DP F
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
CU240E-2 F
Factory setting
- [rpm]
Description:
Displays the speed actual value measured using the BERO.
Dependency:
Refer to: p0580, p0583
Note:
For p0580 = 0 (no measuring probe), a value of zero is displayed here.
r0587
CO: Measuring probe, measuring time measured / MT t_meas measured
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
-
Displays the time between the last two BERO pulses.
The measuring time is specified as 32-bit value with a resolution of 1/48 µs.
If a new pulse is not received before the maximum measured time in p0583 expires, then r0587 is set to the maximum measuring time.
Dependency:
Refer to: p0580
Note:
For p0580 = 0 (no measuring probe), a value of zero is displayed here.
r0588
CO: Measuring probe, pulse counter / MT pulse counter
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the number of measuring pulses that have occurred (been received) up until now.
Dependency:
Refer to: p0580
Note:
After reaching 4294967295 (2^32 - 1), the counter starts again at 0.
r0589
Measuring probe, delay time / MT t_delay
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
-
Displays the time since the last measuring pulse was detected.
The delay time is specified as 32-bit value with a resolution of 1/48 µs.
When a measuring pulse occurs (is received) the delay time is reset and is limited to the maximum measuring time
in p0583.
Dependency:
Refer to: p0580
Note:
For p0580 = 0 (no measuring probe), a value of zero is displayed here.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-77
Parameters
List of Parameters
p0595
Selecting technological units / Select tech units
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C(5)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
46
Factory setting
1
Description:
Selects the units for the parameters of the technology controller.
Value:
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:
16:
17:
18:
19:
20:
21:
22:
23:
24:
25:
26:
27:
28:
29:
30:
31:
32:
33:
34:
35:
36:
37:
38:
39:
40:
41:
42:
43:
44:
45:
46:
Dependency:
Only units of parameters with unit group 9_1 can be changed over using this parameter.
%
1 referred, no dimensions
bar
°C
Pa
ltr/s
m³/s
ltr/min
m³/min
ltr/h
m³/h
kg/s
kg/min
kg/h
t/min
t/h
N
kN
Nm
psi
°F
gallon/s
inch³/s
gallon/min
inch³/min
gallon/h
inch³/h
lb/s
lb/min
lb/h
lbf
lbf ft
K
rpm
parts/min
m/s
ft³/s
ft³/min
BTU/min
BTU/h
mbar
inch wg
ft wg
m wg
% r.h.
g/kg
Refer to: p0596
1-78
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0596
Reference quantity, technological units / Ref tech units
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.01
Max
340.28235E36
Factory setting
1.00
Description:
Sets the reference quantity for the technological units. When changing over using changeover parameter 595 to
absolute units, all of the parameters involved refer to the reference quantity.
Dependency:
Refer to: p0595
p0601[0...n]
Motor temperature sensor type / Mot_temp_sens type
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
4
Factory setting
0
Description:
Sets the sensor type for the motor temperature monitoring.
Value:
0:
1:
2:
4:
Dependency:
The thermal motor model is only calculated for p0612.1 = 1.
Caution:
If, for a selected KTY temperature sensor (p0601 = 2), the motor temperature sensor is not connected but another
encoder, then the temperature adaptation of the motor resistances must be switched out (p0620 = 0). Otherwise, in
controlled-loop operation, torque errors will occur that will mean that the drive will not be able to be stopped.
Note:
PTC thermistor (p0601 = 1): Tripping resistance = 1650 Ohm.
p0604[0...n]
No sensor
PTC alarm & timer
KTY84
Bimetallic NC contact alarm & timer
Motor temperature alarm threshold / Mot_temp al thr
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
0.0 [°C]
Max
240.0 [°C]
Factory setting
130.0 [°C]
Description:
Sets the alarm threshold for monitoring the motor temperature.
Dependency:
Refer to: p0606
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The hysteresis for canceling the alarm is 2 Kelvin.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-79
Parameters
List of Parameters
p0605[0...n]
Motor temperature fault threshold / Mot_temp flt thr
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
0.0 [°C]
Max
240.0 [°C]
Factory setting
145.0 [°C]
Description:
Sets the fault threshold for monitoring the motor temperature.
Caution:
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Note:
The hysteresis for canceling the fault is 2 Kelvin.
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0606[0...n]
Description:
Motor temperature timer / Mot_temp timer
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [s]
Max
600.000 [s]
Factory setting
0.000 [s]
Sets the timer for the alarm threshold for the motor temperature monitoring function.
This timer is started when the temperature alarm threshold (p0604) is exceeded.
If the timer expires before the temperature in the meantime falls below the alarm threshold, the fault F07011 is output.
If the temperature fault threshold (p0605) is prematurely exceeded before the timer has expired, then fault F07011
is immediately output.
As long as the motor temperature has still not exceeded the fault threshold and the alarm thresholds have again
been undershot, the fault can be acknowledged.
Dependency:
Refer to: p0604, p0605
Refer to: F07011, A07910
Note:
With p0606 = 0 s, the timer is de-activated and only the fault threshold is effective.
KTY sensor: When setting the minimum value, the timer is disabled and a fault is not output until p0605 is
exceeded.
PTC sensor, bimetallic NC contact: The timer minimum value has no special significance.
p0607[0...n]
Description:
Temperature sensor fault timer / Sensor fault time
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [s]
Max
600.000 [s]
Factory setting
0.100 [s]
Sets the timer between the output of alarm and fault for a temperature sensor fault.
If there is a sensor fault, this timer is started. If the sensor fault is still present after the timer has expired, a corresponding fault message is output.
Notice:
The parameterized time is internally rounded-off to an integer multiple of 48 ms.
Note:
If the motor is an induction motor, the timer is switched off when setting the minimum value and no alarm is output.
Temperature monitoring is then based on the thermal model.
1-80
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0610[0...n]
Motor overtemperature response / Mot temp response
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: C(3), T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
1
Description:
Sets the system response when the motor temperature reaches the alarm threshold.
Value:
0:
1:
2:
Dependency:
Refer to: p0601, p0604, p0605
No response only alarm no reduction of I_max
Alarm with reduction of I_max and fault
Alarm and fault no reduction of I_max
Refer to: F07011, A07910
Note:
The I_max reduction is not executed for PTC (p0601 = 1) or bimetallic NC contact (p0601 = 4).
The I_max reduction results in a lower output frequency.
If value = 0:
p0606 is not started, therefore only alarm A07910 is output.
If value = 1:
PTC: Same as value = 2 because there is no reduction in I_max.
KTY84: Alarm A07910 is output, I_max is reduced and p0606 is started. After p0606 has elapsed, fault F0711 is
set.
If value = 2:
Alarm A07910 is output and p0606 is started. After p0606 has elapsed, fault F0711 is set.
p0611[0...n]
Description:
I2t motor model thermal time constant / I2t mot_mod T
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0 [s]
Max
20000 [s]
Factory setting
0 [s]
Sets the winding time constant.
The time constant specifies the warm-up time of the cold stator winding when loaded with the motor standstill current up until a temperature rise of 63 % of the continuously permissible winding temperature has been reached.
Dependency:
This parameter is only used for synchronous motors (p0300 = 2xx).
Refer to: r0034, p0612, p0615
Refer to: F07011, A07012, A07910
Caution:
This parameter is automatically pre-set from the motor database for motors from the motor list (p0301).
When selecting a catalog motor, this parameter cannot be changed (write protection). Information in p0300 should
be carefully observed when removing write protection.
Note:
When parameter p0611 is reset to 0, then this switches out the thermal I2t motor model (also refer to p0612).
If no temperature sensor is parameterized, then the ambient temperature for the thermal motor model is referred to
p0625.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-81
Parameters
List of Parameters
p0612[0...n]
Thermal motor model configuration / Therm Mot_mod conf
Access level: 3
Calculated: p0340 = 1
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the configuration for the thermal motor model.
Bit field:
Bit
00
01
Dependency:
Refer to: r0034, p0611, p0615
Note:
Re bit 00:
Signal name
Activate I2t motor model
Activate motor temperature model
Factory setting
0010 bin
1 signal
Yes
Yes
0 signal
No
No
FP
-
This bit is only used for permanent-magnet synchronous motors (p0300 = 2xx). It is only possible to switch in thermal I2t monitoring with a time constant greater than zero (p0611 > 0).
Re bit 01:
This bit is used to activate/de-activate the thermal motor model for induction motors.
p0615[0...n]
I2t motor model fault threshold / I2t mot_mod thresh
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
0.0 [°C]
Max
220.0 [°C]
Factory setting
180.0 [°C]
Description:
Sets the fault threshold for monitoring using the thermal I2t motor model.
Dependency:
The parameter is only used for permanent-magnet synchronous motors (p0300 = 2xx).
Refer to: r0034, p0611, p0612
Refer to: F07011, A07012
Caution:
p0620[0...n]
When selecting a catalog motor (p0301), this parameter is automatically pre-assigned and is write protected. Information in p0300 should be carefully observed when removing write protection.
Thermal adaptation, stator and rotor resistance / Mot therm_adapt R
Access level: 4
Calculated: p0340 = 1
Data type: Integer16
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
1
Description:
Sets the thermal adaptation of the stator/primary section resistance and rotor/secondary section resistance according to r0395 and r0396.
Value:
0:
1:
2:
Note:
For p0620 = 1, the following applies:
No thermal adaptation of stator and rotor resistances
Resistances adapted to the temperatures of the thermal model
Resistances adapted to the measured stator winding temperature
The stator resistance is adapted using the temperature in r0035 and the rotor resistance together with the model
temperature in r0633.
For p0620 = 2, the following applies:
The stator resistance is adapted using the temperature in r0035. If applicable, the rotor temperature for adapting
the rotor resistance is calculated from the stator temperature (r0035) as follows:
theta_R = (r0628 + r0625) / (r0627 + r0625) * r0035
1-82
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0621[0...n]
Description:
Identification stator resistance after restart / Rst_ident Restart
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(3), T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
0
Selects the identification of the stator resistance after booting the Control Unit (only for vector control).
The identification is used to measure the actual stator resistance and from the ratio of the result of motor data identification (p0350) to the matching ambient temperature (p0625) the actual mean temperature of the stator winding is
calculated. The result is used to initialize the thermal motor model.
p0621 = 1:
Identification of the stator resistance only when the drive is powered up for the first time (pulse enable) after booting
the Control Unit.
p0621 = 2:
Identification of the stator resistance every time the drive is powered up (pulse enable).
Value:
0:
1:
2:
No Rs identification
Rs identification after switching-on again
Rs identification after switching-on each time
Dependency:
- perform motor data identification (see p1910) with cold motor.
- enter ambient temperature at time of motor data identification in p0625.
Refer to: p0622, r0623
Notice:
The calculated stator temperature can only be compared with the measured value of a temperature sensor (KTY) to
a certain extent, as the sensor is usually the warmest point of the stator winding, whereas the measured value of
identification reflects the mean value of the stator winding.
Furthermore this is a short-time measurement with limited accuracy that is performed during the magnetizing phase
of the induction motor.
Note:
The measurement is carried out:
- For induction motors
- When vector control is active (see p1300)
- If a temperature sensor (KTY) has not been connected
- When the motor is at a standstill when switched on
When a flying restart is performed on a rotating motor, the temperatures of the thermal motor model are set to a
third of the overtemperatures. This occurs only once, however, when the CU is booted (e.g. after a power failure).
If identification is activated, the magnetizing time is determined via p0622 and not via p0346. Quick magnetizing
(p1401.6) is de-energized internally and alarm A07416 is displayed. The speed is enabled after completion of the
measurement.
p0622[0...n]
Motor excitation time for Rs_ident after powering up again / t_excit Rs_id
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [s]
Max
20.000 [s]
Factory setting
0.000 [s]
Description:
Sets the excitation time of the motor for the stator resistance identification after powering up again (restart).
Dependency:
Refer to: p0621, r0623
Note:
For p0622 < p0346 the following applies:
If identification is activated, the magnetizing time is influenced by p0622. The speed is enabled after measurement
is complete, but not before the time in p0346 has elapsed (see r0056 bit 4). The time taken for measurement also
depends on the settling time of the measured current.
For p0622 >= p0346 the following applies:
Parameter p0622 is internally limited to the magnetizing time p0346, so that p0346 represents the maximum possible magnetizing time during identification. The entire measurement period (magnetizing plus measurement settling
time plus measuring time) will always be greater than p0346.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-83
Parameters
List of Parameters
r0623
Stator resistance of Rs identification after powering up again / R_Stator Reset_Id
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Description:
Displays the identified stator resistance after the Rs identification after powering up again.
Dependency:
Refer to: p0621, p0622
p0625[0...n]
Motor ambient temperature / Mot T_ambient
Access level: 3
Calculated: p0340 = 1,2
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
-40 [°C]
Max
80 [°C]
Factory setting
20 [°C]
Description:
Defines the ambient temperature of the motor for calculating the motor temperature model.
Note:
The parameters for stator and rotor resistance (p0350, p0354) refer to this temperature.
If the thermal I2t motor model is activated for permanent-magnet synchronous motors (refer to p0611), p0625 is
included in the model calculation if a temperature sensor is not being used (see p0601).
p0626[0...n]
Motor overtemperature, stator core / Mot T_over core
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_2
Unit selection: p0505
Min
20 [K]
Max
200 [K]
Factory setting
50 [K]
Description:
Defines the rated overtemperature of the stator core referred to the ambient temperature.
Dependency:
For 1LA7 motors (refer to p0300), the parameter is pre-set as a function of p0307 and p0311.
Refer to: p0625
Note:
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
p0627[0...n]
Motor overtemperature, stator winding / Mot T_over stator
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_2
Unit selection: p0505
Min
20 [K]
Max
200 [K]
Factory setting
80 [K]
Description:
Defines the rated overtemperature of the stator winding referred to the ambient temperature.
Dependency:
For 1LA7 motors (refer to p0300), the parameter is pre-set as a function of p0307 and p0311.
Refer to: p0625
Note:
1-84
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0628[0...n]
Motor overtemperature rotor winding / Mot T_over rotor
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: 21_2
Unit selection: p0505
Min
20 [K]
Max
200 [K]
Factory setting
100 [K]
Description:
Defines the rated overtemperature of the squirrel cage rotor referred to ambient temperature.
Dependency:
For 1LA7 motors (refer to p0300), the parameter is pre-set as a function of p0307 and p0311.
Refer to: p0625
Note:
When quick commissioning is exited with p3900 > 0, then the parameter is reset if a catalog motor has not been
selected (refer to p0300).
r0630[0...n]
Motor temperature model ambient temperature / MotTMod T_amb.
Description:
r0631[0...n]
Description:
r0632[0...n]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2006
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
- [°C]
Max
- [°C]
Factory setting
- [°C]
Displays the ambient temperature of the motor temperature model.
Motor temperature model, stator core temperature / MotTMod T_core
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2006
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
- [°C]
Max
- [°C]
Factory setting
- [°C]
Displays the stator core temperature of the motor temperature model.
Motor temperature model, stator winding temperature / MotTMod T_copper
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2006
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
- [°C]
Max
- [°C]
Factory setting
- [°C]
Description:
Displays the stator winding temperature of the motor temperature model.
r0633[0...n]
Motor temperature model, rotor temperature / MotTMod T_rotor
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2006
Data set: MDS
Units group: 21_1
Unit selection: p0505
Min
- [°C]
Max
- [°C]
Factory setting
- [°C]
Displays the rotor temperature of the motor temperature model.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-85
Parameters
List of Parameters
p0634[0...n]
Description:
Q flux flux constant unsaturated / PSIQ KPSI UNSAT
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.000 [Vsrms]
Max
100.000 [Vsrms]
Factory setting
0.000 [Vsrms]
The non-linear and cross-coupled quadrature axis flux functions are defined using 4 coefficients.
The parameter weights the unsaturated component of the quadrature axis flux function.
p0635[0...n]
Description:
Q flux quadrature axis current constant unsaturated / PSIQ KIQ UNSAT
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
The non-linear and cross-coupled quadrature axis flux functions are defined using 4 coefficients.
This parameter describes the interdependency of the unsaturated component of the quadrature axis current.
Dependency:
Refer to: p0634
p0636[0...n]
Q flux direct axis current constant unsaturated / PSIQ KID UNSAT
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
The non-linear and cross-coupled quadrature axis flux functions are defined using 4 coefficients.
This parameter describes the interdependency of the unsaturated component of the direct axis current.
Dependency:
Refer to: p0634
p0637[0...n]
Q flux flux gradient saturated / PSIQ Grad SAT
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(3), U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [mH]
Max
10000.00 [mH]
Factory setting
0.00 [mH]
Description:
The non-linear and cross-coupled quadrature axis flux functions are defined using 4 coefficients.
Dependency:
Refer to: p0634, p0635, p0636
This parameter describes the gradients of the saturated component over the quadrature axis current.
1-86
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0640[0...n]
Current limit / Current limit
Access level: 2
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: C(1, 3), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
Description:
Sets the current limit.
Dependency:
Refer to: r0209, p0323
Note:
The parameter is part of the quick commissioning (p0010 = 1); this means that it is appropriately pre-assigned when
changing p0305. The current limit p0640 is limited to r0209.
The resulting current limit is displayed in r0067 and if required, r0067 is reduced by the thermal model of the power
unit.
The torque and power limits (p1520, p1521, p1530, p1531) matching the current limit are automatically calculated
when exiting the quick commissioning using p3900 > 0 or using the automatic parameterization with p0340 = 3, 5.
p0640 is limited to 4.0 x p0305.
p0640 is pre-assigned for the automatic self commissioning routine (e.g. to 1.5 x p0305, with p0305 = r0207[1]).
p0640 must be entered when commissioning the system. This is the reason that p0640 is not calculated by the
automatic parameterization when exiting the quick commissioning (p3900 > 0).
p0641[0...n]
Description:
CI: Current limit, variable / Curr lim var
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the signal source for the variable current limit.
The value is referred to p0640.
p0650[0...n]
Description:
Actual motor operating hours / Mot t_oper act
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0 [h]
Max
4294967295 [h]
Factory setting
0 [h]
Displays the operating hours for the corresponding motor.
The motor operating time counter continues to run when the pulses are enabled. When the pulse enable is withdrawn, the counter is held and the value saved.
Dependency:
Refer to: p0651
Refer to: A01590
Note:
The operating hours counter in p0650 can only be reset to 0. In this case, p0651 is automatically set to 0.
For p0651 = 0, the operating hours counter is disabled.
The operating hours counter only runs with drive data set 0 and 1 (DDS).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-87
Parameters
List of Parameters
p0651[0...n]
Description:
Motor operating hours maintenance interval / Mot t_op maint
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0 [h]
Max
150000 [h]
Factory setting
0 [h]
Sets the service/maintenance intervals in hours for the appropriate motor.
An appropriate fault is output when the operating hours set here are reached.
Dependency:
Refer to: p0650
Refer to: A01590
Note:
For p0651 = 0, the operating hours counter is disabled.
The operating hours counter only runs with drive data set 0 and 1 (DDS).
p0700[0...n]
Command source selection / Cmd src sel
CU240B-2
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
184
Factory setting
0
Description:
Sets the command source.
Value:
0:
2:
6:
100:
101:
110:
120:
150:
181:
182:
183:
184:
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
No Macro
Terminals
Fieldbus
EAQ1
EAQ2
Set enable signals
FBM (fault, operation, signal)
MOP 1
2 Wire type 2
2 Wire type 3
3 Wire type 1
3 Wire type 2
p0700[0...n]
Command source selection / Cmd src sel
CU240B-2 DP
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
184
Description:
Value:
Caution:
1-88
Factory setting
0
Sets the command source.
0:
No Macro
2:
Terminals
6:
Fieldbus
100: EAQ1
101: EAQ2
110: Set enable signals
120: FBM (fault, operation, signal)
140: CDS
150: MOP 1
170: Jog 1
181: 2 Wire type 2
182: 2 Wire type 3
183: 3 Wire type 1
184: 3 Wire type 2
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0700[0...n]
Command source selection / Cmd src sel
CU240E-2
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
184
Factory setting
0
Description:
Sets the command source.
Value:
0:
2:
6:
100:
101:
110:
120:
130:
140:
150:
152:
160:
162:
181:
182:
183:
184:
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
No Macro
Terminals
Fieldbus
EAQ1
EAQ2
Set enable signals
FBM (fault, operation, signal)
Safety 0
CDS
MOP 1
MOP 3
Fix Setpoint 0
Fix Setpoint 2
2 Wire type 2
2 Wire type 3
3 Wire type 1
3 Wire type 2
p0700[0...n]
Command source selection / Cmd src sel
CU240E-2 DP
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
184
Factory setting
0
Description:
Sets the command source.
Value:
0:
2:
6:
100:
101:
110:
120:
130:
140:
150:
152:
160:
162:
170:
181:
182:
183:
184:
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
No Macro
Terminals
Fieldbus
EAQ1
EAQ2
Set enable signals
FBM (fault, operation, signal)
Safety 0
CDS
MOP 1
MOP 3
Fix Setpoint 0
Fix Setpoint 2
Jog 1
2 Wire type 2
2 Wire type 3
3 Wire type 1
3 Wire type 2
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-89
Parameters
List of Parameters
p0700[0...n]
Command source selection / Cmd src sel
CU240E-2 DP F
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
184
Factory setting
0
Description:
Sets the command source.
Value:
0:
2:
6:
100:
101:
110:
120:
130:
131:
140:
150:
152:
160:
162:
170:
181:
182:
183:
184:
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
r0720[0...4]
CU number of inputs and outputs / CU I/O count
No Macro
Terminals
Fieldbus
EAQ1
EAQ2
Set enable signals
FBM (fault, operation, signal)
Safety 0
Safety 1
CDS
MOP 1
MOP 3
Fix Setpoint 0
Fix Setpoint 2
Jog 1
2 Wire type 2
2 Wire type 3
3 Wire type 1
3 Wire type 2
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the number of inputs and outputs
Index:
[0] = Number of digital inputs
[1] = Number of digital outputs
[2] = Number of digital input/outputs bidirectional
[3] = Number of analog inputs
[4] = Number of analog outputs
1-90
Factory setting
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0721
CU digital inputs, terminal actual value / CU DI actual value
CU240B-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the actual value at the digital inputs.
This means that the actual input signal can be checked at terminal DI x or DI/DO x prior to switching from the simulation mode (p0795.x = 1) to terminal mode (p0795.x = 0).
Bit field:
Bit
00
01
02
03
11
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 11 (T. 3, 4) AI 0
Note:
DI: Digital Input
1 signal
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
FP
-
T: Terminal
r0721
CU digital inputs, terminal actual value / CU DI actual value
CU240E-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
-
Displays the actual value at the digital inputs.
This means that the actual input signal can be checked at terminal DI x or DI/DO x prior to switching from the simulation mode (p0795.x = 1) to terminal mode (p0795.x = 0).
Bit field:
Bit
00
01
02
03
04
05
11
12
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 4 (T. 16)
DI 5 (T. 17)
DI 11 (T. 3, 4) AI 0
DI 12 (T. 10, 11) AI 1
Note:
DI: Digital Input
1 signal
High
High
High
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
Low
Low
Low
FP
-
T: Terminal
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-91
Parameters
List of Parameters
r0722.0...11
CO/BO: CU digital inputs, status / CU DI status
CU240B-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status of the digital inputs.
Bit field:
Bit
00
01
02
03
11
Dependency:
Refer to: r0723
Notice:
To the terminal designation:
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 11 (T. 3, 4) AI 0
Factory setting
1 signal
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
FP
-
The first designation is valid for CU320, the second for CU310.
Note:
AI: Analog Input
DI: Digital Input
T: Terminal
r0722.0...12
CO/BO: CU digital inputs, status / CU DI status
CU240E-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Displays the status of the digital inputs.
Bit field:
Bit
00
01
02
03
04
05
11
12
Dependency:
Refer to: r0723
Notice:
To the terminal designation:
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 4 (T. 16)
DI 5 (T. 17)
DI 11 (T. 3, 4) AI 0
DI 12 (T. 10, 11) AI 1
Factory setting
1 signal
High
High
High
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
Low
Low
Low
FP
-
The first designation is valid for CU320, the second for CU310.
Note:
AI: Analog Input
DI: Digital Input
T: Terminal
1-92
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0723.0...11
CO/BO: CU digital inputs, status inverted / CU DI status inv
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the inverted status of the digital inputs.
Bit field:
Bit
00
01
02
03
11
Dependency:
Refer to: r0722
Notice:
To the terminal designation:
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 11 (T. 3, 4) AI 0
Factory setting
1 signal
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
FP
-
The first designation is valid for CU320, the second for CU310.
Note:
DI: Digital Input
T: Terminal
r0723.0...12
CO/BO: CU digital inputs, status inverted / CU DI status inv
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Displays the inverted status of the digital inputs.
Bit field:
Bit
00
01
02
03
04
05
11
12
Dependency:
Refer to: r0722
Notice:
To the terminal designation:
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 4 (T. 16)
DI 5 (T. 17)
DI 11 (T. 3, 4) AI 0
DI 12 (T. 10, 11) AI 1
Factory setting
1 signal
High
High
High
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
Low
Low
Low
FP
-
The first designation is valid for CU320, the second for CU310.
Note:
DI: Digital Input
T: Terminal
p0724
CU digital inputs debounce time / CU DI t_debounce
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [ms]
Max
20.000 [ms]
Description:
Sets the debounce time for digital inputs.
Note:
The digital inputs are read in cyclically every 2 ms (DI 11, DI 12 every 4 ms).
Factory setting
4.000 [ms]
To debounce the signals, the set debounce time is converted into integer multiple debounce clock cycles Tp (Tp =
p0724 / 2 ms).
DI: Digital Input
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-93
Parameters
List of Parameters
p0730
BI: CU signal source for terminal DO 0 / CU S_src DO 0
Access level: 2
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
52.3
Description:
Sets the signal source for terminal DO 0 (NO: T. 19 / NC: T. 18).
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
DO: Digital Output
T: Terminal
Relay output: NO = normally open, NC = normally closed
p0731
BI: CU signal source for terminal DO 1 / CU S_src DO 1
CU240E-2
Access level: 2
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
52.7
Description:
Sets the signal source for terminal DO 1 (NO: T. 21).
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
DO: Digital Output
T: Terminal
Relay output: NO = normally open, NC = normally closed
p0732
BI: CU signal source for terminal DO 2 / CU S_src DO 2
CU240E-2
Access level: 2
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
52.2
Description:
Sets the signal source for terminal DO 2 (NO: T. 24 / NC: T. 23).
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
DO: Digital Output
T: Terminal
Relay output: NO = normally open, NC = normally closed
r0747
CU, digital outputs status / CU DO status
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status of digital outputs.
Bit field:
Bit
00
Note:
DO: Digital Output
Signal name
DO 0 (NO: T. 19 / NC: T. 18)
Factory setting
1 signal
High
0 signal
Low
FP
-
T: Terminal
Relay output: NO = normally open, NC = normally closed
Inversion using p0748 has been taken into account.
1-94
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0747
CU, digital outputs status / CU DO status
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Displays the status of digital outputs.
Bit field:
Bit
00
01
02
Note:
DO: Digital Output
Signal name
DO 0 (NO: T. 19 / NC: T. 18)
DO 1 (NO: T. 21)
DO 2 (NO: T. 24 / NC: T. 23)
Factory setting
1 signal
High
High
High
0 signal
Low
Low
Low
FP
-
T: Terminal
Relay output: NO = normally open, NC = normally closed
Inversion using p0748 has been taken into account.
p0748
CU, invert digital outputs / CU DO inv
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Setting to invert the signals at the digital outputs.
Bit field:
Bit
00
Note:
DO: Digital Output
Signal name
DO 0 (NO: T. 19 / NC: T. 18)
Factory setting
0000 bin
1 signal
Inverted
0 signal
Not inverted
FP
-
T: Terminal
Relay output: NO = normally open, NC = normally closed
p0748
CU, invert digital outputs / CU DO inv
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Setting to invert the signals at the digital outputs.
Bit field:
Bit
00
01
02
Note:
DO: Digital Output
Signal name
DO 0 (NO: T. 19 / NC: T. 18)
DO 1 (NO: T. 21)
DO 2 (NO: T. 24 / NC: T. 23)
Factory setting
0000 bin
1 signal
Inverted
Inverted
Inverted
0 signal
Not inverted
Not inverted
Not inverted
FP
-
T: Terminal
Relay output: NO = normally open, NC = normally closed
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-95
Parameters
List of Parameters
r0751.0...9
BO: CU analog inputs status word / CU AI status word
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status of analog inputs.
Bit field:
Bit
00
01
08
09
Note:
AI: Analog Input
r0752[0...1]
CO: CU analog inputs input voltage/current actual / CU AI U/I_inp act
Signal name
Analog input AI0 wire breakage
Analog input AI1 wire breakage
Analog input AI0 no wire breakage
Analog input AI1 no wire breakage
1 signal
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the actual input voltage in V when set as voltage input.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Dependency:
The type of analog input AIx (voltage or current input) is set using p0756.
FP
-
Factory setting
-
Displays the actual input current in mA when set as current input and with the load resistor switched in.
Refer to: p0756
Note:
AI: Analog Input
T: Terminal
p0753[0...1]
CU analog inputs smoothing time constant / CU AI T_smooth
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
1000.0 [ms]
Factory setting
0.0 [ms]
Description:
Sets the smoothing time constant of the 1st-order low pass filter for the analog inputs.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
AI: Analog Input
T: Terminal
1-96
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0755[0...1]
Description:
CO: CU analog inputs actual value in percent / CU AI value in %
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the currently referred input value of the analog inputs.
When interconnected, the signals are referred to the reference quantities p200x and p205x.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
AI: Analog Input
T: Terminal
p0756[0...1]
CU analog inputs type / CU AI type
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
8
Factory setting
[0] 4
[1] 4
Description:
Sets the type of analog inputs.
p0756[0...1] = 0, 1, 4 corresponds to a voltage input (r0752, p0757, p0759 are displayed in V).
p0756[0...1] = 2, 3 corresponds to a current input (r0752, p0757, p0759 are displayed in mA).
In addition, the associated DIP switch must be set.
For the voltage input, DIP switch AI0/1 must be set to "U".
For the current input, DIP switch AI0/1 or AI2 must be set to "I".
Value:
0:
1:
2:
3:
4:
8:
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
The maximum voltage difference between analog input terminals AI+, AI-, and the ground must not exceed 35 V.
Warning:
Unipolar voltage input (0 V ... +10 V)
Unipolar voltage input monitored (+2 V ... +10 V)
Unipolar current input (0 mA ... +20 mA)
Unipolar current input monitored (+4 mA to +20 mA)
Bipolar voltage input (-10 V ... +10 V)
No sensor connected
If the system is operated when the load resistor is switched on (DIP switch set to "I"), the voltage between differential inputs AI+ and AI- must not exceed 10 V or the injected 80 mA current otherwise the input will be damaged.
Note:
When changing p0756 , the parameters of the scaling characteristic (p0757, p0758, p0759, p0760) are overwritten
with the following default values:
For p0756 = 0, 1, 4, p0757 is set to 0.0 V, p0758 = 0.0 %, p0759 = 10.0 V and p0760 = 100.0 %.
For p0756 = 2, p0757 is set to 0.0 mA, p0758 = 0.0 %, p0759 = 20.0 mA and p0760 = 100.0 %.
For p0756 = 3, p0757 is set to 4.0 mA, p0758 = 0.0 %, p0759 = 20.0 mA and p0760 = 100.0 %.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-97
Parameters
List of Parameters
p0757[0...1]
Description:
CU analog inputs characteristic value x1 / CU AI char x1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-50.000
Max
160.000
Factory setting
0.000
Sets the scaling characteristic for the analog inputs.
The scaling characteristic for the analog inputs is defined using 2 points.
This parameter specifies the x coordinate (V, mA) of the 1st value pair of the characteristic.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
The parameters for the characteristic do not have a limiting effect.
p0758[0...1]
CU analog inputs characteristic value y1 / CU AI char y1
Description:
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-1000.00 [%]
Max
1000.00 [%]
Factory setting
0.00 [%]
Sets the scaling characteristic for the analog inputs.
The scaling characteristic for the analog inputs is defined using 2 points.
This parameter specifies the y coordinate (percentage) of the 1st value pair of the characteristic.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
The parameters for the characteristic do not have a limiting effect.
p0759[0...1]
CU analog inputs characteristic value x2 / CU AI char x2
Description:
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-50.000
Max
160.000
Factory setting
10.000
Sets the scaling characteristic for the analog inputs.
The scaling characteristic for the analog inputs is defined using 2 points.
This parameter specifies the x coordinate (V, mA) of the 2nd value pair of the characteristic.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
The parameters for the characteristic do not have a limiting effect.
p0760[0...1]
Description:
CU analog inputs characteristic value y2 / CU AI char y2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-1000.00 [%]
Max
1000.00 [%]
Factory setting
100.00 [%]
Sets the scaling characteristic for the analog inputs.
The scaling characteristic for the analog inputs is defined using 2 points.
This parameter specifies the y coordinate (percentage) of the 2nd value pair of the characteristic.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
The parameters for the characteristic do not have a limiting effect.
1-98
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0761[0...1]
Description:
Index:
Dependency:
Note:
p0762[0...1]
CU analog inputs wire breakage monitoring response threshold / CU WireBrkThresh
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
20.00
Sets the response threshold for the wire breakage monitoring of the analog inputs.
The unit for the parameter value depends on the set analog input type.
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
For the following analog input type, the wire breakage monitoring is active:
p0756[0...1] = 1 (unipolar voltage input monitored (+2 V ... +10 V)), unit [V]
p0756[0...1] = 3 (unipolar current input monitored (+4 mA ... +20 mA)), unit [mA]
Refer to: p0756
AI: Analog Input
When p0761 = 0, wire breakage monitoring is not carried out.
CU analog inputs wire breakage monitoring delay time / CU wire brk t_del
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [ms]
Max
1000 [ms]
Description:
Sets the delay time for the wire breakage monitoring of the analog inputs.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Note:
AI: Analog Input
p0771[0...1]
Factory setting
2.00
Factory setting
100 [ms]
CI: CU analog outputs signal source / CU AO S_src
Access level: 2
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 21[0]
[1] 27[0]
Description:
Sets the signal source for the analog outputs.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Note:
AO: Analog Output
T: Terminal
r0772[0...1]
Description:
Index:
Note:
CU analog outputs, output value currently referred / CU AO outp_val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the actual referred output value of the analog outputs.
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
AO: Analog Output
T: Terminal
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-99
Parameters
List of Parameters
p0773[0...1]
CU analog outputs smoothing time constant / CU AO T_smooth
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
1000.0 [ms]
Factory setting
0.0 [ms]
Description:
Sets the smoothing time constant of the 1st-order low pass filter for the analog outputs.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Note:
AO: Analog Output
T: Terminal
r0774[0...1]
CU analog outputs output voltage/current actual / CU AO U/I_outp
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the actual output voltage or output current at the analog outputs.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Dependency:
Refer to: p0776
Note:
AO: Analog Output
Factory setting
-
T: Terminal
p0775[0...1]
CU analog outputs activate absolute value generation / CU AO absVal act
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Activates the absolute value generation for the analog outputs.
Value:
0:
1:
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Note:
AO: Analog Output
Factory setting
0
No absolute value generation
Absolute value generation switched in
T: Terminal
1-100
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0776[0...1]
Description:
CU analog outputs type / CU AO type
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
0
Sets the analog output type.
p0776[x] = 1 corresponds to a voltage output (p0774, p0778, p0780 are displayed in V).
p0776[x] = 0, 2 corresponds to a current output (p0774, p0778, p0780 are displayed in mA).
Value:
0:
1:
2:
Current output (0 mA ... +20 mA)
Voltage output (0 V ... +10 V)
Current output (+4 mA ... +20 mA)
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Note:
When changing p0776, the parameters of the scaling characteristic (p0777, p0778, p0779, p0780) are overwritten
with the following default values:
For p0776 = 0, p0777 is set to 0.0 %, p0778 = 0.0 mA, p0779 = 100.0 % and p0780 to 20.0 mA.
For p0776 = 1, p0777 is set to 0.0 %, p0778 = 0.0 V, p0779 = 100.0 % and p0780 to 10.0 V.
For p0776 = 2, p0777 is set to 0.0 %, p0778 = 4.0 mA, p0779 = 100.0 % and p0780 to 20.0 mA.
p0777[0...1]
Description:
CU analog outputs characteristic value x1 / CU AO char x1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-1000.00 [%]
Max
1000.00 [%]
Factory setting
0.00 [%]
Sets the scaling characteristic for the analog outputs.
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the x coordinate (percentage) of the 1st value pair of the characteristic.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Dependency:
Refer to: p0776
Notice:
This parameter is automatically overwritten when the analog output type is changed (p0776).
Note:
This parameter is automatically overwritten if p0776 (type of analog output) is changed.
The parameters for the characteristic do not have a limiting effect.
p0778[0...1]
Description:
Index:
Dependency:
Notice:
Note:
CU analog outputs characteristic value y1 / CU char y1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-20.000 [V]
Max
20.000 [V]
Factory setting
0.000 [V]
Sets the scaling characteristic for the analog outputs.
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the y coordinate (output voltage in V or output current in mA) of the 1st value pair of the
characteristic.
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
The unit of this parameter (V or mA) depends on the analog input type.
Refer to: p0776
This parameter is automatically overwritten when the analog output type is changed (p0776).
This parameter is automatically overwritten if p0776 (type of analog output) is changed.
The parameters for the characteristic do not have a limiting effect.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-101
Parameters
List of Parameters
p0779[0...1]
Description:
CU analog outputs characteristic value x2 / CU char x2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-1000.00 [%]
Max
1000.00 [%]
Factory setting
100.00 [%]
Sets the scaling characteristic for the analog outputs.
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the x coordinate (percentage) of the 2nd value pair of the characteristic.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Dependency:
Refer to: p0776
Notice:
This parameter is automatically overwritten when the analog output type is changed (p0776).
Note:
This parameter is automatically overwritten if p0776 (type of analog output) is changed.
The parameters for the characteristic do not have a limiting effect.
p0780[0...1]
Description:
CU analog outputs characteristic value y2 / CU char y2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-20.000 [V]
Max
20.000 [V]
Factory setting
20.000 [V]
Sets the scaling characteristic for the analog outputs.
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the y coordinate (output voltage in V or output current in mA) of the 2nd value pair of the
characteristic.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Dependency:
The unit of this parameter (V or mA) depends on the analog input type.
Refer to: p0776
Notice:
This parameter is automatically overwritten when the analog output type is changed (p0776).
Note:
This parameter is automatically overwritten if p0776 (type of analog output) is changed.
The parameters for the characteristic do not have a limiting effect.
p0782[0...1]
BI: CU analog outputs invert signal source / CU AO inv S_src
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to invert the analog output signals.
Index:
[0] = AO0 (T 12/13)
[1] = AO1 (T 26/27)
Note:
AO: Analog Output
Factory setting
0
T: Terminal
1-102
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0785.0...1
BO: CU analog outputs status word / CU AO ZSW
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status of analog outputs.
Bit field:
Bit
00
01
Note:
AO: Analog Output
p0795
CU digital inputs simulation mode / CU DI simulation
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Signal name
AO 0 negative
AO 1 negative
1 signal
Yes
Yes
FP
-
Factory setting
0000 0000 0000 0000 bin
Description:
Sets the simulation mode for digital inputs.
Bit field:
Bit
00
01
02
03
11
Dependency:
The setpoint for the input signals is specified using p0796.
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 11 (T. 3, 4) AI 0
0 signal
No
No
1 signal
Simulation
Simulation
Simulation
Simulation
Simulation
0 signal
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
FP
-
Refer to: p0796
Note:
This parameter is not saved when data is backed up (p0971).
DI: Digital Input
T: Terminal
p0795
CU digital inputs simulation mode / CU DI simulation
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
0000 0000 0000 0000 bin
Description:
Sets the simulation mode for digital inputs.
Bit field:
Bit
00
01
02
03
04
05
11
12
Dependency:
The setpoint for the input signals is specified using p0796.
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 4 (T. 16)
DI 5 (T. 17)
DI 11 (T. 3, 4) AI 0
DI 12 (T. 10, 11) AI 1
1 signal
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
Simulation
0 signal
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
Terminal eval.
FP
-
Refer to: p0796
Note:
This parameter is not saved when data is backed up (p0971).
DI: Digital Input
T: Terminal
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-103
Parameters
List of Parameters
p0796
CU digital inputs simulation mode setpoint / CU DI simul setp
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240B-2 DP
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0000 0000 0000 bin
Description:
Sets the setpoint for the input signals in the digital input simulation mode.
Bit field:
Bit
00
01
02
03
11
Dependency:
The simulation of a digital input is selected using p0795.
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 11 (T. 3, 4) AI 0
1 signal
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
FP
-
Refer to: p0795
Notice:
To the terminal designation:
The first designation is valid for CU320, the second for CU310.
Note:
This parameter is not saved when data is backed up (p0971).
AI: Analog Input
DI: Digital Input
T: Terminal
p0796
CU digital inputs simulation mode setpoint / CU DI simul setp
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
0000 0000 0000 0000 bin
Description:
Sets the setpoint for the input signals in the digital input simulation mode.
Bit field:
Bit
00
01
02
03
04
05
11
12
Dependency:
The simulation of a digital input is selected using p0795.
Signal name
DI 0 (T. 5)
DI 1 (T. 6)
DI 2 (T. 7)
DI 3 (T. 8)
DI 4 (T. 16)
DI 5 (T. 17)
DI 11 (T. 3, 4) AI 0
DI 12 (T. 10, 11) AI 1
1 signal
High
High
High
High
High
High
High
High
0 signal
Low
Low
Low
Low
Low
Low
Low
Low
FP
-
Refer to: p0795
Notice:
To the terminal designation:
The first designation is valid for CU320, the second for CU310.
Note:
This parameter is not saved when data is backed up (p0971).
AI: Analog Input
DI: Digital Input
T: Terminal
1-104
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0797[0...1]
CU analog inputs simulation mode / CU AI sim_mode
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Sets the simulation mode for the analog inputs.
Value:
0:
1:
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Dependency:
The setpoint for the input voltage is specified via p0798.
Factory setting
0
No simulation mode for analog input x
Simulation mode for analog input x
Refer to: p0798
Note:
This parameter is not saved when data is backed up (p0971).
AI: Analog Input
p0798[0...1]
CU analog inputs simulation mode setpoint / CU AI sim setp
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-50.000
Max
2000.000
Factory setting
0.000
Description:
Sets the setpoint for the input value in the simulation mode of the analog inputs.
Index:
[0] = AI0 (T. 3/4)
[1] = AI1 (T. 10/11)
Dependency:
The simulation of an analog input is selected using p0797.
If AI x is parameterized as a voltage input (p0756), the setpoint is a voltage in V.
If AI x is parameterized as a current input (p0756), the setpoint is a current in mA.
Refer to: p0756, p0797
Note:
This parameter is not saved when data is backed up (p0971).
AI: Analog Input
p0802
Description:
Data transfer: memory card as source/target / mem_card src/targ
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
100
Factory setting
0
Sets the number for data transfer of a parameter backup from/to memory card.
Transfer from memory card to device memory (p0804 = 1):
- Sets the source of parameter backup (e.g. p0802 = 48 --> PS048xxx.ACX is the source).
Transfer from non-volatile device memory to memory card (p0804 = 2):
- Sets the target of parameter backup (e.g. p0802 = 23 --> PS023xxx.ACX is the target).
Dependency:
Refer to: p0803, p0804
Notice:
If the data between the volatile and non-volatile device memories differ, then it may be necessary to save the data
on the memory card in a non-volatile fashion prior to the transfer (e.g. p0971 = 1).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-105
Parameters
List of Parameters
p0803
Description:
Data transfer: device memory as source/target / Dev_mem src/targ
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
12
Factory setting
0
Sets the number for data transfer of a parameter backup from/to device memory.
Transfer from memory card to device memory (p0804 = 1):
- Sets the target of the parameter backup (e.g. p0803 = 10 --> PS010xxx.ACX is the target).
Transfer from non-volatile device memory to memory card (p0804 = 2):
- Sets the source of the parameter backup (e.g. p0803 = 11 --> PS011xxx.ACX is the source).
Value:
0:
10:
11:
12:
Source/target standard
Source/target with setting 10
Source/target with setting 11
Source/target with setting 12
Dependency:
Refer to: p0802, p0804
Notice:
If the data between the volatile and non-volatile device memories differ, then it may be necessary to save the data
on the memory card in a non-volatile fashion prior to the transfer (e.g. p0971 = 1).
1-106
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0804
Data transfer start / Data transf start
CU240B-2
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0
Max
1100
Description:
Factory setting
0
Sets the transfer direction and start of data transfer between the memory card and non-volatile device memory.
Example 1:
The parameter backup is to be transferred from the device memory to the memory card with setting 0. The parameter backup is to be stored on the memory card with setting 22.
p0802 = 22 (parameter backup stored on memory card as target with setting 22)
p0803 = 0 (parameter backup stored in device memory as source with setting 0)
p0804 = 2 (start data transfer from device memory to memory card)
--> PS000xxx.ACX is transferred from device memory to memory card and stored as PS022xxx.ACX.
Example 2:
The parameter backup is to be transferred from the memory card to the device memory with setting 22. The parameter backup is to be stored in the device memory as setting 0.
p0802 = 22 (parameter backup stored on memory card as source with setting 22)
p0803 = 0 (parameter backup stored in device memory as target with setting 0)
p0804 = 1 (start data transfer from memory card to device memory)
--> PS022xxx.ACX is transferred from memory card to device memory and stored as PS000xxx.ACX.
Example 3 (not supported for PROFIBUS devices):
The communication configuration is to be transferred from the device memory to the memory card.
p0802 = (not relevant)
p0803 = (not relevant)
p0804 = 12 (start transferring the device master data (GSD) to the memory card)
--> The files that are relevant for the communication configuration are transferred from the device memory to the
memory card and stored in the /SIEMENS/SINAMICS/DATA/CFG directory.
Value:
0:
1:
2:
1001:
1002:
1003:
1100:
Inactive
Memory card to device memory
Device memory to memory card
File on memory card cannot be opened
File in device memory cannot be opened
Memory card not found
File cannot be transferred
Dependency:
Refer to: p0802, p0803
Notice:
The memory card must not be removed while data is being transferred.
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
If a parameter backup with setting 0 is detected on the memory card when the Control Unit is switched on
(PS000xxx.ACX), this is transferred automatically to the device memory.
When the memory card is inserted, a parameter backup with setting 0 (PS000xxx.ACX) is automatically written to
the memory card when the parameters are saved in a non-volatile memory (e.g. by means of "Copy RAM to ROM").
Once the data has been successfully transferred, this parameter is automatically reset to 0. If an error occurs, the
parameter is set to a value > 1000. Possible fault causes:
p0804 = 1001:
The parameter backup set in p0802 as the source on the memory card does not exist or there is not sufficient memory space available on the memory card.
p0804 = 1002:
The parameter backup set in p0803 as the source in the device memory does not exist or there is not sufficient
memory space available in the device memory.
p0804 = 1003:
No memory card has been inserted.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-107
Parameters
List of Parameters
p0804
Data transfer start / Data transf start
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
1100
Description:
Factory setting
0
Sets the transfer direction and start of data transfer between the memory card and non-volatile device memory.
Example 1:
The parameter backup is to be transferred from the device memory to the memory card with setting 0. The parameter backup is to be stored on the memory card with setting 22.
p0802 = 22 (parameter backup stored on memory card as target with setting 22)
p0803 = 0 (parameter backup stored in device memory as source with setting 0)
p0804 = 2 (start data transfer from device memory to memory card)
--> PS000xxx.ACX is transferred from device memory to memory card and stored as PS022xxx.ACX.
Example 2:
The parameter backup is to be transferred from the memory card to the device memory with setting 22. The parameter backup is to be stored in the device memory as setting 0.
p0802 = 22 (parameter backup stored on memory card as source with setting 22)
p0803 = 0 (parameter backup stored in device memory as target with setting 0)
p0804 = 1 (start data transfer from memory card to device memory)
--> PS022xxx.ACX is transferred from memory card to device memory and stored as PS000xxx.ACX.
Example 3 (not supported for PROFIBUS devices):
The communication configuration is to be transferred from the device memory to the memory card.
p0802 = (not relevant)
p0803 = (not relevant)
p0804 = 12 (start transferring the device master data (GSD) to the memory card)
--> The files that are relevant for the communication configuration are transferred from the device memory to the
memory card and stored in the /SIEMENS/SINAMICS/DATA/CFG directory.
Value:
0:
1:
2:
12:
1001:
1002:
1003:
1100:
Inactive
Memory card to device memory
Device memory to memory card
Device memory (communication configuration) to memory card
File on memory card cannot be opened
File in device memory cannot be opened
Memory card not found
File cannot be transferred
Dependency:
Refer to: p0802, p0803
Notice:
The memory card must not be removed while data is being transferred.
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
1-108
If a parameter backup with setting 0 is detected on the memory card when the Control Unit is switched on
(PS000xxx.ACX), this is transferred automatically to the device memory.
When the memory card is inserted, a parameter backup with setting 0 (PS000xxx.ACX) is automatically written to
the memory card when the parameters are saved in a non-volatile memory (e.g. by means of "Copy RAM to ROM").
Once the data has been successfully transferred, this parameter is automatically reset to 0. If an error occurs, the
parameter is set to a value > 1000. Possible fault causes:
p0804 = 1001:
The parameter backup set in p0802 as the source on the memory card does not exist or there is not sufficient memory space available on the memory card.
p0804 = 1002:
The parameter backup set in p0803 as the source in the device memory does not exist or there is not sufficient
memory space available in the device memory.
p0804 = 1003:
No memory card has been inserted.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0806
BI: Inhibit master control / PcCtrl inhibit
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to block the master control.
Dependency:
Refer to: r0807
Note:
The commissioning software (drive control panel) uses the master control.
r0807.0
BO: Master control active / PcCtrl active
Description:
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays what has the master control.
The drive can be controlled via the BICO interconnection or from external (e.g. the commissioning software).
Bit field:
Bit
00
Signal name
Master control active
1 signal
Yes
0 signal
No
FP
5030,
6031
Dependency:
Refer to: p0806
Notice:
The master control only influences control word 1 and speed setpoint 1. Other control words/setpoints can be transferred from another automation device.
Note:
Bit 0 = 0: BICO interconnection active
Bit 0 = 1: Master control for PC/OP
The master control is used from the commissioning software (drive control panel) and from the Operator Panel (OP,
LOCAL mode).
p0809[0...2]
Copy Command Data Set CDS / Copy CDS
Access level: 2
Calculated: -
Data type: Unsigned8
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Description:
Copies one Command Data Set (CDS) into another.
Index:
[0] = Source Command Data Set
[1] = Target Command Data Set
[2] = Start copying procedure
Dependency:
Refer to: r3996
Notice:
When the command data sets are copied, short-term communication interruptions may occur.
Note:
Procedure:
1. In Index 0, enter which command data set should be copied.
2. In Index 1, enter the command data set that is to be copied into.
3. Start copying: Set index 2 from 0 to 1.
p0809[2] is automatically set to 0 when copying is completed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-109
Parameters
List of Parameters
p0810
BI: Command data set selection CDS bit 0 / CDS select., bit 0
CU240B-2
Access level: 2
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the Command Data Set bit 0 (CDS bit 0).
Dependency:
Refer to: r0050, p0811, r0836
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
The Command Data Set selected using the binector inputs is displayed in r0836.
The currently effective command data set is displayed in r0050.
A Command Data Set can be copied using p0809.
p0810
BI: Command data set selection CDS bit 0 / CDS select., bit 0
CU240B-2 DP
Access level: 2
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
722.3
Description:
Sets the signal source to select the Command Data Set bit 0 (CDS bit 0).
Dependency:
Refer to: r0050, p0811, r0836
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
The Command Data Set selected using the binector inputs is displayed in r0836.
The currently effective command data set is displayed in r0050.
A Command Data Set can be copied using p0809.
p0811
BI: Command data set selection CDS bit 1 / CDS select., bit 1
Access level: 2
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the Command Data Set bit 1 (CDS bit 1).
Dependency:
Refer to: r0050, p0810, r0836
Note:
The Command Data Set selected using the binector inputs is displayed in r0836.
The currently effective command data set is displayed in r0050.
A Command Data Set can be copied using p0809.
1-110
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0819[0...2]
Copy Drive Data Set DDS / Copy DDS
Access level: 2
Calculated: -
Data type: Unsigned8
Can be changed: C(15)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Description:
Copies one Drive Data Set (DDS) into another.
Index:
[0] = Source Drive Data Set
[1] = Target Drive Data Set
[2] = Start copying procedure
Dependency:
Refer to: r3996
Factory setting
0
Notice:
When the drive data sets are copied, short-term communication interruptions may occur.
Note:
Procedure:
1. In Index 0, enter which drive data set is to be copied.
2. In Index 1, enter the drive data set data that is to be copied into.
3. Start copying: Set index 2 from 0 to 1.
p0819[2] is automatically set to 0 when copying is completed.
p0820[0...n]
BI: Drive Data Set selection DDS bit 0 / DDS select., bit 0
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: C(15), T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the Drive Data Set, bit 0 (DDS, bit 0).
Dependency:
Refer to: r0051, p0826, r0837
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p0821[0...n]
BI: Drive Data Set selection DDS bit 1 / DDS select., bit 1
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: C(15), T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the Drive Data Set, bit 1 (DDS, bit 1).
Dependency:
Refer to: r0051, r0837
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-111
Parameters
List of Parameters
p0826[0...n]
Description:
Note:
r0835.2...8
Motor changeover, motor number / Mot_chng mot No.
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: C(3), T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Sets the freely-assignable motor number for the drive data set changeover.
If the same motor is driven by different drive data sets, the same motor number must also be entered in these data
sets.
If the motor is also switched with the drive data set, different motor numbers must be used. In this case, the data set
can only be switched when the pulse inhibit is set.
If the motor numbers are identical, the same thermal motor model is used for calculation after data set changeover.
If different motor numbers are used, different models are also used for calculating (the inactive motor cools down in
each case).
For the same motor number, the correction values of the Rs, Lh or kT adaptation are applied for the data set
changeover (refer to r1782, r1787, r1797).
CO/BO: Data set changeover status word / DDS_ZSW
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status word for the drive data set changeover.
Bit field:
Bit
02
04
05
07
08
Note:
Re bit 02:
A data set changeover is delayed by the time required for the internal parameter calculation.
Re bit 04:
A data set changeover is only carried out when the armature short circuit is not activated.
Re bit 05:
A data set changeover is only carried out when pole position identification is not running.
Re bit 07:
A data set changeover is only carried out when rotating measurement is not running.
Re bit 08:
A data set changeover is only carried out when motor data identification is not running.
r0836.0...1
Signal name
Internal parameter calculation active
Armature short circuit active
Identification running
Rotating measurement running
Motor data identification running
1 signal
Yes
Yes
Yes
Yes
Yes
FP
-
CO/BO: Command Data Set CDS selected / CDS selected
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the command data set (CDS) selected via the binector input.
Bit field:
Bit
00
01
Dependency:
Note:
Refer to: r0050, p0810, p0811
Command data sets are selected via binector input p0810 and following.
The currently effective command data set is displayed in r0050.
1-112
0 signal
No
No
No
No
No
Signal name
CDS select. bit 0
CDS select. bit 1
1 signal
ON
ON
0 signal
OFF
OFF
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0837.0...1
CO/BO: Drive Data Set DDS selected / DDS selected
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the drive data set (DDS) selected via the binector input.
Bit field:
Bit
00
01
Dependency:
Refer to: r0051, p0820, p0821
Note:
Drive data sets are selected via binector input p0820 and following.
Signal name
DDS select. bit 0
DDS select. bit 1
1 signal
ON
ON
0 signal
OFF
OFF
FP
-
The currently effective drive data set is displayed in r0051.
If there is only one data set, then a value of 0 is displayed in this parameter and not the selection via binector inputs.
p0840[0...n]
BI: ON / OFF (OFF1) / ON / OFF (OFF1)
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 722.0
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source for the command "ON/OFF (OFF1)".
For the PROFIdrive profile, this command corresponds to control word 1 bit 0 (STW1.0).
Dependency:
Refer to: p1055, p1056
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
For binector input p0840 = 0 signal, the motor can be moved, jogging using binector input p1055 or p1056.
The command "ON/OFF (OFF1)" can be issued using binector input p0840 or p1055/p1056.
For binector input p0840 = 0 signal, the switch-on inhibit is acknowledged.
Only the signal source that originally powered up can also power down again.
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
For drives with closed-loop speed control (p1300 = 20), the following applies:
- BI: p0840 = 0 signal: OFF1 (braking with the ramp-function generator, then pulse suppression and switch-on
inhibit)
For drives with closed-loop torque control (p1300 = 22), the following applies:
- BI: p0840 = 0 signal: immediate pulse cancellation
For drives with closed-loop torque control (activated using p1501), the following applies:
- BI: p0840 = 0 signal: No dedicated braking response, but pulse suppression when standstill is detected (p1226,
p1227)
For drives with closed-loop speed/torque control, the following applies:
- BI: p0840 = 0/1 signal: ON (pulses can be enabled)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-113
Parameters
List of Parameters
p0840[0...n]
BI: ON / OFF (OFF1) / ON / OFF (OFF1)
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.0
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source for the command "ON/OFF (OFF1)".
For the PROFIdrive profile, this command corresponds to control word 1 bit 0 (STW1.0).
Dependency:
Refer to: p1055, p1056
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
For binector input p0840 = 0 signal, the motor can be moved, jogging using binector input p1055 or p1056.
The command "ON/OFF (OFF1)" can be issued using binector input p0840 or p1055/p1056.
For binector input p0840 = 0 signal, the switch-on inhibit is acknowledged.
Only the signal source that originally powered up can also power down again.
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
For drives with closed-loop speed control (p1300 = 20), the following applies:
- BI: p0840 = 0 signal: OFF1 (braking with the ramp-function generator, then pulse suppression and switch-on
inhibit)
For drives with closed-loop torque control (p1300 = 22), the following applies:
- BI: p0840 = 0 signal: immediate pulse cancellation
For drives with closed-loop torque control (activated using p1501), the following applies:
- BI: p0840 = 0 signal: No dedicated braking response, but pulse suppression when standstill is detected (p1226,
p1227)
For drives with closed-loop speed/torque control, the following applies:
- BI: p0840 = 0/1 signal: ON (pulses can be enabled)
p0844[0...n]
BI: No coast-down / coast-down (OFF2) signal source 1 / OFF2 S_src 1
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the first signal source for the command "No coast down/coast down (OFF2)".
The following signals are AND'ed:
- BI: p0844 "No coast-down / coast-down (OFF2) signal source 1"
- BI: p0845 "No coast-down / coast-down (OFF2) signal source 2"
For the PROFIdrive profile, the result of the AND logic operation corresponds to control word 1 bit 1 (STW1.1).
BI: p0844 = 0 signal or BI: p0845 = 0 signal
- OFF2 (immediate pulse suppression and switch on inhibit)
BI: p0844 = 1 signal and BI: p0845 = 1 signal
Caution:
- No OFF2 (enable is possible)
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
1-114
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0844[0...n]
BI: No coast-down / coast-down (OFF2) signal source 1 / OFF2 S_src 1
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.1
[1] 1
[2] 2090.1
[3] 2090.1
Description:
Sets the first signal source for the command "No coast down/coast down (OFF2)".
The following signals are AND'ed:
- BI: p0844 "No coast-down / coast-down (OFF2) signal source 1"
- BI: p0845 "No coast-down / coast-down (OFF2) signal source 2"
For the PROFIdrive profile, the result of the AND logic operation corresponds to control word 1 bit 1 (STW1.1).
BI: p0844 = 0 signal or BI: p0845 = 0 signal
- OFF2 (immediate pulse suppression and switch on inhibit)
BI: p0844 = 1 signal and BI: p0845 = 1 signal
- No OFF2 (enable is possible)
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p0845[0...n]
Description:
BI: No coast-down / coast-down (OFF2) signal source 2 / OFF2 S_src 2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the second signal source for the command "No coast down/coast down (OFF2)".
The following signals are AND'ed:
- BI: p0844 "No coast-down / coast-down (OFF2) signal source 1"
- BI: p0845 "No coast-down / coast-down (OFF2) signal source 2"
For the PROFIdrive profile, the result of the AND logic operation corresponds to control word 1 bit 1 (STW1.1).
BI: p0844 = 0 signal or BI: p0845 = 0 signal
- OFF2 (immediate pulse suppression and switch on inhibit)
BI: p0844 = 1 signal and BI: p0845 = 1 signal
- No OFF2 (enable is possible)
Caution:
When "master control from PC" is activated, this binector input is effective.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-115
Parameters
List of Parameters
p0848[0...n]
BI: No Quick Stop / Quick Stop (OFF3) signal source 1 / OFF3 S_src 1
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the first signal source for the command "No quick stop/quick stop (OFF3)".
The following signals are AND'ed:
- BI: p0848 "No quick stop / quick stop (OFF3) signal source 1"
- BI: p0849 "No quick stop / quick stop (OFF3) signal source 2"
For the PROFIdrive profile, the result of the AND logic operation corresponds to control word 1 bit 2 (STW1.2).
BI: p0848 = 0 signal or BI: p0849 = 0 signal
- OFF3 (braking along the OFF3 ramp (p1135), then pulse suppression and switch on inhibit)
BI: p0848 = 1 signal and BI: p0849 = 1 signal
- No OFF3 (enable is possible)
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p0848[0...n]
BI: No Quick Stop / Quick Stop (OFF3) signal source 1 / OFF3 S_src 1
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.2
[1] 1
[2] 2090.2
[3] 2090.2
Description:
Sets the first signal source for the command "No quick stop/quick stop (OFF3)".
The following signals are AND'ed:
- BI: p0848 "No quick stop / quick stop (OFF3) signal source 1"
- BI: p0849 "No quick stop / quick stop (OFF3) signal source 2"
For the PROFIdrive profile, the result of the AND logic operation corresponds to control word 1 bit 2 (STW1.2).
BI: p0848 = 0 signal or BI: p0849 = 0 signal
- OFF3 (braking along the OFF3 ramp (p1135), then pulse suppression and switch on inhibit)
BI: p0848 = 1 signal and BI: p0849 = 1 signal
- No OFF3 (enable is possible)
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
1-116
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0849[0...n]
Description:
BI: No Quick Stop / Quick Stop (OFF3) signal source 2 / OFF3 S_src 2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the second signal source for the command "No quick stop/quick stop (OFF3)".
The following signals are AND'ed:
- BI: p0848 "No quick stop / quick stop (OFF3) signal source 1"
- BI: p0849 "No quick stop / quick stop (OFF3) signal source 2"
For the PROFIdrive profile, the result of the AND logic operation corresponds to control word 1 bit 2 (STW1.2).
BI: p0848 = 0 signal or BI: p0849 = 0 signal
- OFF3 (braking along the OFF3 ramp (p1135), then pulse suppression and switch on inhibit)
BI: p0848 = 1 signal and BI: p0849 = 1 signal
- No OFF3 (enable is possible)
Caution:
When "master control from PC" is activated, this binector input is effective.
p0852[0...n]
BI: Enable operation/inhibit operation / Operation enable
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the signal source for the command "enable operation/inhibit operation".
For the PROFIdrive profile, this command corresponds to control word 1 bit 3 (STW1.3).
BI: p0852 = 0 signal
Inhibit operation (suppress pulses).
BI: p0852 = 1 signal
Enable operation (pulses can be enabled).
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-117
Parameters
List of Parameters
p0852[0...n]
BI: Enable operation/inhibit operation / Operation enable
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.3
[1] 1
[2] 2090.3
[3] 2090.3
Description:
Sets the signal source for the command "enable operation/inhibit operation".
For the PROFIdrive profile, this command corresponds to control word 1 bit 3 (STW1.3).
BI: p0852 = 0 signal
Inhibit operation (suppress pulses).
BI: p0852 = 1 signal
Enable operation (pulses can be enabled).
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p0854[0...n]
BI: Control by PLC/no control by PLC / Master ctrl by PLC
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the signal source for the command "control by PLC/no control by PLC".
For the PROFIdrive profile, this command corresponds to control word 1 bit 10 (STW1.10).
BI: p0854 = 0 signal
No control by PLC
BI: p0852 = 1 signal
Control by PLC.
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
This bit is used to initiate a response for the drives when the control fails (F07220). If there is no control available,
then binector input p0854 should be set to 1.
If a control is available, then STW1.10 must be set to 1 (PZD1) so that the received data is updated. This applies
regardless of the setting in p0854 and even in the case of free telegram configuration (p0922 = 999).
1-118
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0854[0...n]
BI: Control by PLC/no control by PLC / Master ctrl by PLC
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.10
[1] 1
[2] 2090.10
[3] 2090.10
Description:
Sets the signal source for the command "control by PLC/no control by PLC".
For the PROFIdrive profile, this command corresponds to control word 1 bit 10 (STW1.10).
BI: p0854 = 0 signal
No control by PLC
BI: p0852 = 1 signal
Control by PLC.
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
This bit is used to initiate a response for the drives when the control fails (F07220). If there is no control available,
then binector input p0854 should be set to 1.
If a control is available, then STW1.10 must be set to 1 (PZD1) so that the received data is updated. This applies
regardless of the setting in p0854 and even in the case of free telegram configuration (p0922 = 999).
p0855[0...n]
BI: Unconditionally release holding brake / Uncond open brake
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the command "unconditionally open holding brake".
Dependency:
Refer to: p0858
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
The signal via BI: p0858 (unconditionally close holding brake) has a higher priority than via BI: p0855 (unconditionally open holding brake).
p0856[0...n]
BI: Speed controller enable / n_ctrl enable
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the signal source for the command "enable speed controller" (r0898.12).
0 signal: Set the I component and speed controller output to zero.
1 signal: Enable speed controller.
Dependency:
Refer to: r0898
Note:
If "enable speed controller" is withdrawn, then an existing brake will be closed.
If "speed controller enable" is withdrawn, the pulses are not suppressed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-119
Parameters
List of Parameters
p0857
Description:
Power unit monitoring time / PU t_monit
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
100.0 [ms]
Max
60000.0 [ms]
Factory setting
10000.0 [ms]
Sets the monitoring time for the power unit.
The monitoring time is started after an 0/1 edge of the ON/OFF1 command. If the power unit does not return a
READY signal within the monitoring time, fault F07802 is output.
Dependency:
Refer to: F07802, F30027
Notice:
The maximum time to pre-charge the DC link is monitored in the power unit and cannot be changed. The maximum
pre-charging duration depends on the power unit.
The monitoring time for the pre-charging is started after the ON command (BI: p0840 = 0/1 signal). Fault F30027 is
output when the maximum pre-charging duration is exceeded.
Note:
The factory setting for p0857 depends on the power unit.
The monitoring time for the ready signal of the power unit includes the time to pre-charge the DC link and, if relevant, the de-bounce time of the contactors.
If an excessively low value is entered into p0857, then after enable, this results in the corresponding fault.
p0858[0...n]
BI: Unconditionally close holding brake / Uncond close brake
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the command "unconditionally close holding brake".
Dependency:
Refer to: p0855
Note:
The signal via BI: p0858 (unconditionally close holding brake) has a higher priority than via BI: p0855 (unconditionally open holding brake).
For a 1 signal via BI: p0858, the command "unconditionally close the holding brake" is executed and internally a
zero setpoint is entered.
p0897
BI: Parking axis selection / Parking axis sel
Access level: 2
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to select the "parking axis" function.
Dependency:
BI: p0897 = 0 signal
Factory setting
0
The function "parking axis" is not selected.
BI: p0897 = 1 signal
The function "parking axis" is selected.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
After it has been selected the "parking axis" function only becomes active when the pulses are suppressed.
1-120
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0898.0...14
CO/BO: Control word sequence control / STW seq_ctrl
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the control word of the sequence control.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
12
14
Note:
OC: Operating condition
Signal name
ON/OFF1
OC / OFF2
OC / OFF3
Operation enable
Ramp-function generator enable
Continue ramp-function generator
Speed setpoint enable
Command open brake
Jog 1
Jog 2
Master ctrl by PLC
Speed controller enable
Command close brake
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
FP
-
Re bit 10:
If p0700 = 2 is set, bit 10 always shows "1".
r0899.0...13
CO/BO: Status word sequence control / ZSW seq_ctrl
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status word of the sequence control.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
11
12
13
Note:
Re bits 00, 01, 02, 04, 05, 06, 09:
Signal name
Rdy for switch on
Ready
Operation enabled
Jog active
No coasting active
No Quick Stop active
Switching on inhibited active
Drive ready
Controller enable
Control request
Pulses enabled
Open holding brake
Command close holding brake
Factory setting
1 signal
Yes
Yes
Yes
Yes
OFF2 inactive
OFF3 inactive
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
OFF2 active
OFF3 active
No
No
No
No
No
No
No
FP
-
For PROFIdrive, these signals are used for status word 1.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-121
Parameters
List of Parameters
p0918
PROFIBUS address / PB address
CU240B-2 DP
Access level: 2
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
1
Max
126
Description:
Factory setting
126
Displays or sets the PROFIBUS address for PROFIBUS interface on the Control Unit.
The address can be set as follows:
1) Using the DIP switch on the Control Unit.
--> p0918 can then only be read and displays the selected address.
--> A change only becomes effective after a POWER ON.
2) Using p0918
--> Only if all of the DIP switches are set to ON or OFF.
--> The address is saved in a non-volatile fashion using the function "copy from RAM to ROM".
--> A change only becomes effective after a POWER ON.
Notice:
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
For p0014 = 0, the following applies:
Before a changed setting becomes permanently effective, a non-volatile RAM to ROM data save is required. To do
this, set p0971 = 1 or p0014 = 1.
Note:
Permissible PROFIBUS addresses: 1 ... 126
Address 126 is used for commissioning.
Every PROFIBUS address change only becomes effective after a POWER ON.
p0922
PROFIdrive telegram selection / PD Telegr_sel
CU240B-2 DP
Access level: 1
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: C(1), T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
1
Max
999
Factory setting
1
Description:
Sets the send and receive telegram.
Value:
1:
20:
350:
352:
353:
354:
999:
Dependency:
Refer to: F01505
Note:
If a value is not equal to 999, a telegram is set and the automatically set interconnections in the telegram are inhibited.
Standard telegram 1, PZD-2/2
Standard telegram 20, PZD-2/6
SIEMENS telegram 350, PZD-4/4
SIEMENS telegram 352, PZD-6/6
SIEMENS telegram 353, PZD-2/2, PKW-4/4
SIEMENS telegram 354, PZD-6/6, PKW-4/4
Free telegram configuration with BICO
The inhibited interconnections can only be changed again after setting value 999.
r0944
CO: Counter for fault buffer changes / Fault buff change
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays fault buffer changes. This counter is incremented every time the fault buffer changes.
Dependency:
Refer to: r0945, r0947, r0948, r0949, r2109
1-122
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0945[0...63]
Fault code / Fault code
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the numbers of faults that have occurred.
Dependency:
Refer to: r0947, r0948, r0949, r2109, r2130, r2133, r2136
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
Fault buffer structure (general principle):
r0945[0], r0949[0], r0948[0], r2109[0] --> actual fault case, fault 1
...
r0945[7], r0949[7], r0948[7], r2109[7] --> actual fault case, fault 8
r0945[8], r0949[8], r0948[8], r2109[8] --> 1st acknowledged fault case, fault 1
...
r0945[15], r0949[15], r0948[15], r2109[15] --> 1st acknowledged fault case, fault 8
...
r0945[56], r0949[56], r0948[56], r2109[56] --> 7th acknowledged fault case, fault 1
...
r0945[63], r0949[63], r0948[63], r2109[63] --> 7th acknowledged fault case, fault 8
r0946[0...65534] Fault code list / Fault code list
Description:
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Lists the fault codes stored in the drive unit.
The indices can only be accessed with a valid fault code.
Dependency:
The parameter assigned to the fault code is entered in r0951 under the same index.
r0947[0...63]
Fault number / Fault number
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
This parameter is identical to r0945.
r0948[0...63]
Fault time received in milliseconds / t_fault recv ms
Description:
Dependency:
Notice:
Note:
Factory setting
-
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Factory setting
- [ms]
Displays the system runtime in milliseconds when the fault occurred.
Refer to: r0945, r0947, r0949, r2109, r2130, r2133, r2136
The time comprises r2130 (days) and r0948 (milliseconds).
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the fault buffer and the assignment of the indices is shown in r0945.
When the parameter is read via PROFIdrive, the TimeDifference data type applies.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-123
Parameters
List of Parameters
r0949[0...63]
Fault value / Fault value
Access level: 3
Calculated: -
Data type: Integer32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays additional information about the fault that occurred (as integer number).
Dependency:
Refer to: r0945, r0947, r0948, r2109, r2130, r2133, r2136
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the fault buffer and the assignment of the indices is shown in r0945.
p0952
Fault cases, counter / Fault cases qty
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Description:
Number of fault situations that have occurred since the last reset.
Dependency:
The fault buffer is deleted (cleared) by setting p0952 to 0.
Factory setting
0
Refer to: r0945, r0947, r0948, r0949, r2109, r2130, r2133, r2136
r0963
PROFIBUS baud rate / PB baud rate
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Displays the corresponding value for the PROFIBUS baud rate.
Value:
0:
1:
2:
3:
4:
6:
7:
8:
9:
10:
11:
255:
1-124
Factory setting
-
9.6 kbit/s
19.2 kbit/s
93.75 kbit/s
187.5 kbit/s
500 kbit/s
1.5 Mbit/s
3 Mbit/s
6 Mbit/s
12 Mbit/s
31.25 kbit/s
45.45 kbit/s
Baud rate unknown
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0964[0...6]
Device identification / Device ident.
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the device identification.
Index:
[0] = Company (Siemens = 42)
[1] = Device type
[2] = Firmware version
[3] = Firmware date (year)
[4] = Firmware date (day/month)
[5] = Number of drive objects
[6] = Firmware patch/hot fix
Note:
Example:
Factory setting
-
r0964[0] = 42 --> SIEMENS
r0964[1] = device type, see below
r0964[2] = 403 --> first part of the firmware version V04.03 (for second part, refer to index 6)
r0964[3] = 2010 --> year 2010
r0964[4] = 1705 --> 17th of May
r0964[5] = 1 --> 1 drive object
r0964[6] = 200 --> second part, firmware version (complete version: V04.03.02.00)
Device type:
r0964[1] = 6100 --> SINAMICS G120 CU240B-2 DP
r0964[1] = 6103 --> SINAMICS G120 CU240B-2
r0964[1] = 6210 --> SINAMICS G120 CU240E-2 DP
r0964[1] = 6213 --> SINAMICS G120 CU240E-2
r0964[1] = 6220 --> SINAMICS G120 CU240E-2 DP-F
r0964[1] = 6223 --> SINAMICS G120 CU240E-2 F
r0965
PROFIdrive profile number / PD profile number
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the PROFIdrive profile number and profile version.
Constant value = 0329 hex.
Byte 1: Profile number = 03 hex = PROFIdrive profile
Byte 2: Profile version = 29 hex = Version 4.1
Note:
When the parameter is read via PROFIdrive, the Octet String 2 data type applies.
p0969
System runtime relative / t_System relative
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [ms]
Max
4294967295 [ms]
Description:
Displays the system runtime in ms since the last POWER ON.
Note:
The value in p0969 can only be reset to 0.
Factory setting
0 [ms]
The value overflows after approx. 49 days.
When the parameter is read via PROFIdrive, the TimeDifference data type applies.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-125
Parameters
List of Parameters
p0970
Description:
Reset drive parameters / Drive par reset
Access level: 1
Calculated: -
Data type: Unsigned16
Can be changed: C(1, 30)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
300
Factory setting
0
The parameter is used to initiate the reset of the drive parameters.
Parameters p0100, p0205 are not reset.
The following motor parameters are defined in accordance with the power unit: p0300 ... p0311.
When downloading settings 10, 11, 12, the buffer memory mode is automatically deactivated (p0014 = 0).
Value:
0:
1:
5:
10:
11:
12:
100:
300:
Inactive
Start a parameter reset
Starts a safety parameter reset
Starts to download setting 10
Starts to download setting 11
Starts to download setting 12
Start a BICO interconnection reset
Only Siemens internal
Dependency:
Refer to: F01659
Caution:
When the buffer memory is active (see p0014), the actual parameters are backed up from RAM to ROM when a
parameter set is loaded (p0970 = 10, 11, 12).
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Peculiarities of communication via PROFIBUS DP:
- Communication with Class 1 masters (e.g. S7 controllers) is interrupted.
- Communication with Class 2 masters (e.g. STARTER) is retained.
Note:
A factory setting run can only be started if p0010 was first set to 30 (parameter reset).
At the end of the calculations, p0970 is automatically set to 0.
Parameter reset has been completed if p0970 and p0010 have been set to 0.
For p0970 = 5 the following applies:
The password for Safety Integrated must be set.
When Safety Integrated is enabled, this can result in error messages, which then require an acceptance test to be
performed.
Then save the parameters and carry out a POWER ON.
For p0970 = 1 the following applies:
If a Safety Integrated function is parameterized (p9601), then the safety parameters are not reset. In this case, an
error message (F01659) is output with fault value 2.
The following generally applies:
One index of parameters p2100, p2101, p2118, p2119, p2126, p2127 is not reset, if a parameterized message is
precisely active in this index.
1-126
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p0971
Save parameters / Save par
Access level: 1
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
12
Description:
Setting to save parameters in the non-volatile memory.
Value:
0:
1:
10:
11:
12:
Dependency:
Refer to: p1960, r3996
Caution:
If a memory card (optional) is inserted, the following applies:
Factory setting
0
Inactive
Save drive object
Save in non-volatile memory as setting 10
Save in non-volatile memory as setting 11
Save in non-volatile memory as setting 12
The parameters are also saved on the card and therefore overwrite any existing data!
Caution:
The Control Unit power supply may only be powered down after data has been saved (i.e. after data save has been
started, wait until the parameter again has the value 0).
Notice:
Writing to parameters is inhibited while saving.
The progress while saving is displayed in r3996.
p0972
Drive unit reset / Drv_unit reset
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Description:
Sets the required procedure to execute a hardware reset for the drive unit.
Value:
0:
1:
2:
3:
Danger:
It must be absolutely ensured that the system is in a safe condition.
Factory setting
0
Inactive
Hardware-Reset immediate
Hardware reset preparation
Hardware reset after cyclic communication has failed
The memory card/device memory of the Control Unit must not be accessed.
Note:
If value = 1:
Reset is immediately executed and communications interrupted.
After communications have been established, check the reset operation (refer below).
If value = 2:
Help to check the reset operation.
Firstly, set p0972 = 2 and then read back. Secondly, set p0972 = 1 (it is possible that this request is possibly no longer acknowledged). The communication is then interrupted.
After communications have been established, check the reset operation (refer below).
If value = 3:
The reset is executed after interrupting cyclic communication. This setting is used to implement a synchronized
reset by a control for several drive units.
If the cyclic communication is active for both PROFIdrive interfaces, then the reset is executed after completing
both cycle communications.
After communications have been established, check the reset operation (refer below).
To check the reset operation:
After the drive unit has been restarted and communications have been established, read p0972 and check the following:
p0972 = 0? --> The reset was successfully executed.
p0972 > 0? --> The reset was not executed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-127
Parameters
List of Parameters
r0980[0...299]
List of existing parameters 1 / List avail par 1
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the parameters that exist for this drive.
Dependency:
Refer to: r0981, r0989
Note:
The existing parameters are displayed in indices 0 to 298. If an index contains the value 0, then the list ends here.
In a long list, index 299 contains the parameter number at which position the list continues.
This list consists solely of the following parameters:
r0980[0...299], r0981[0...299] ... r0989[0...299]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0981[0...299]
List of existing parameters 2 / List avail par 2
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the parameters that exist for this drive.
Dependency:
Refer to: r0980, r0989
Note:
The existing parameters are displayed in indices 0 to 298. If an index contains the value 0, then the list ends here.
In a long list, index 299 contains the parameter number at which position the list continues.
This list consists solely of the following parameters:
r0980[0...299], r0981[0...299] ... r0989[0...299]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0989[0...299]
List of existing parameters 10 / List avail par 10
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the parameters that exist for this drive.
Dependency:
Refer to: r0980, r0981
Note:
The existing parameters are displayed in indices 0 to 298. If an index contains the value 0, then the list ends here.
This list consists solely of the following parameters:
r0980[0...299], r0981[0...299] ... r0989[0...299]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
1-128
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r0990[0...99]
List of modified parameters 1 / List chang. par 1
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays those parameters with a value other than the factory setting for this drive.
Dependency:
Refer to: r0991, r0999
Note:
Modified parameters are displayed in indices 0 to 98. If an index contains the value 0, then the list ends here. In a
long list, index 99 contains the parameter number at which position the list continues.
This list consists solely of the following parameters:
r0990[0...99], r0991[0...99] ... r0999[0...99]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0991[0...99]
List of modified parameters 2 / List chang. par 2
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays those parameters with a value other than the factory setting for this drive.
Dependency:
Refer to: r0990, r0999
Note:
Modified parameters are displayed in indices 0 to 98. If an index contains the value 0, then the list ends here. In a
long list, index 99 contains the parameter number at which position the list continues.
This list consists solely of the following parameters:
r0990[0...99], r0991[0...99] ... r0999[0...99]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0999[0...99]
List of modified parameters 10 / List chang. par 10
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays those parameters with a value other than the factory setting for this drive.
Dependency:
Refer to: r0990, r0991
Note:
Modified parameters are displayed in indices 0 to 98. If an index contains the value 0, then the list ends here.
This list consists solely of the following parameters:
r0990[0...99], r0991[0...99] ... r0999[0...99]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-129
Parameters
List of Parameters
p1000[0...n]
Speed setpoint selection / n_set sel
CU240B-2
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
200
Description:
Factory setting
2
Sets the source for the speed setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
1:
2:
3:
6:
10:
11:
12:
13:
16:
20:
21:
22:
23:
26:
30:
31:
32:
33:
36:
60:
61:
62:
63:
66:
200:
No main setpoint
Motorized potentiometer
Analog setpoint
Fixed speed setpoint
Fieldbus
Motor potentiometer + no main setpoint
Motor potentiometer + motor potentiometer
Motor potentiometer + analog setpoint
Motor potentiometer + fixed speed setpoint
Motor potentiometer + fieldbus
Analog setpoint + no main setpoint
Analog setpoint + motor potentiometer
Analog setpoint + analog setpoint
Analog setpoint + fixed speed setpoint
Analog setpoint + fieldbus
Fixed speed setpoint + no main setpoint
Fixed speed setpoint + motor potentiometer
Fixed speed setpoint + analog setpoint
Fixed speed setpoint + fixed speed setpoint
Fixed speed setpoint + fieldbus
Fieldbus + no main setpoint
Fieldbus + motor potentiometer
Fieldbus + analog setpoint
Fieldbus + fixed speed setpoint
Fieldbus+fieldbus
Analog output connection
Dependency:
When changing this parameter, the following settings are influenced:
Caution:
Refer to: p1070, p1071, p1075, p1076
If p1000 is selected as the main setpoint of the fieldbus, the following BICO interconnection is set automatically:
p2051[1] = r0063
Caution:
1-130
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1000[0...n]
Speed setpoint selection / n_set sel
CU240B-2 DP
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
200
Description:
Factory setting
6
Sets the source for the speed setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
1:
2:
3:
6:
10:
11:
12:
13:
16:
20:
21:
22:
23:
26:
30:
31:
32:
33:
36:
60:
61:
62:
63:
66:
200:
No main setpoint
Motorized potentiometer
Analog setpoint
Fixed speed setpoint
Fieldbus
Motor potentiometer + no main setpoint
Motor potentiometer + motor potentiometer
Motor potentiometer + analog setpoint
Motor potentiometer + fixed speed setpoint
Motor potentiometer + fieldbus
Analog setpoint + no main setpoint
Analog setpoint + motor potentiometer
Analog setpoint + analog setpoint
Analog setpoint + fixed speed setpoint
Analog setpoint + fieldbus
Fixed speed setpoint + no main setpoint
Fixed speed setpoint + motor potentiometer
Fixed speed setpoint + analog setpoint
Fixed speed setpoint + fixed speed setpoint
Fixed speed setpoint + fieldbus
Fieldbus + no main setpoint
Fieldbus + motor potentiometer
Fieldbus + analog setpoint
Fieldbus + fixed speed setpoint
Fieldbus+fieldbus
Analog output connection
Dependency:
When changing this parameter, the following settings are influenced:
Caution:
Refer to: p1070, p1071, p1075, p1076
If p1000 is selected as the main setpoint of the fieldbus, the following BICO interconnection is set automatically:
p2051[1] = r0063
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-131
Parameters
List of Parameters
p1000[0...n]
Speed setpoint selection / n_set sel
CU240E-2
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
200
Description:
Factory setting
2
Sets the source for the speed setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
1:
2:
3:
6:
7:
10:
11:
12:
13:
16:
17:
20:
21:
22:
23:
26:
27:
30:
31:
32:
33:
36:
37:
60:
61:
62:
63:
66:
67:
70:
71:
72:
73:
76:
77:
200:
Dependency:
When changing this parameter, the following settings are influenced:
Refer to: p1070, p1071, p1075, p1076
If p1000 is selected as the main setpoint of the fieldbus, the following BICO interconnection is set automatically:
p2051[1] = r0063
Caution:
Caution:
1-132
No main setpoint
Motorized potentiometer
Analog setpoint
Fixed speed setpoint
Fieldbus
Analog setpoint 2
Motor potentiometer + no main setpoint
Motor potentiometer + motor potentiometer
Motor potentiometer + analog setpoint
Motor potentiometer + fixed speed setpoint
Motor potentiometer + fieldbus
Motor potentiometer + analog setpoint 2
Analog setpoint + no main setpoint
Analog setpoint + motor potentiometer
Analog setpoint + analog setpoint
Analog setpoint + fixed speed setpoint
Analog setpoint + fieldbus
Analog setpoint + analog setpoint 2
Fixed speed setpoint + no main setpoint
Fixed speed setpoint + motor potentiometer
Fixed speed setpoint + analog setpoint
Fixed speed setpoint + fixed speed setpoint
Fixed speed setpoint + fieldbus
Fixed speed setpoint + analog setpoint 2
Fieldbus + no main setpoint
Fieldbus + motor potentiometer
Fieldbus + analog setpoint
Fieldbus + fixed speed setpoint
Fieldbus+fieldbus
Fieldbus + analog setpoint 2
Analog setpoint 2 + no main setpoint
Analog setpoint 2 + motor potentiometer
Analog setpoint 2 + analog setpoint
Analog setpoint 2 + fixed speed setpoint
Analog setpoint 2 + fieldbus
Analog setpoint 2 + analog setpoint 2
Analog output connection
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1000[0...n]
Speed setpoint selection / n_set sel
CU240E-2 DP
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2 DP F
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
200
Description:
Factory setting
6
Sets the source for the speed setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
1:
2:
3:
6:
7:
10:
11:
12:
13:
16:
17:
20:
21:
22:
23:
26:
27:
30:
31:
32:
33:
36:
37:
60:
61:
62:
63:
66:
67:
70:
71:
72:
73:
76:
77:
200:
Dependency:
When changing this parameter, the following settings are influenced:
Refer to: p1070, p1071, p1075, p1076
If p1000 is selected as the main setpoint of the fieldbus, the following BICO interconnection is set automatically:
p2051[1] = r0063
Caution:
Caution:
No main setpoint
Motorized potentiometer
Analog setpoint
Fixed speed setpoint
Fieldbus
Analog setpoint 2
Motor potentiometer + no main setpoint
Motor potentiometer + motor potentiometer
Motor potentiometer + analog setpoint
Motor potentiometer + fixed speed setpoint
Motor potentiometer + fieldbus
Motor potentiometer + analog setpoint 2
Analog setpoint + no main setpoint
Analog setpoint + motor potentiometer
Analog setpoint + analog setpoint
Analog setpoint + fixed speed setpoint
Analog setpoint + fieldbus
Analog setpoint + analog setpoint 2
Fixed speed setpoint + no main setpoint
Fixed speed setpoint + motor potentiometer
Fixed speed setpoint + analog setpoint
Fixed speed setpoint + fixed speed setpoint
Fixed speed setpoint + fieldbus
Fixed speed setpoint + analog setpoint 2
Fieldbus + no main setpoint
Fieldbus + motor potentiometer
Fieldbus + analog setpoint
Fieldbus + fixed speed setpoint
Fieldbus+fieldbus
Fieldbus + analog setpoint 2
Analog setpoint 2 + no main setpoint
Analog setpoint 2 + motor potentiometer
Analog setpoint 2 + analog setpoint
Analog setpoint 2 + fixed speed setpoint
Analog setpoint 2 + fieldbus
Analog setpoint 2 + analog setpoint 2
Analog output connection
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-133
Parameters
List of Parameters
p1001[0...n]
CO: Fixed speed setpoint 1 / n_set_fixed 1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 1.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1002[0...n]
CO: Fixed speed setpoint 2 / n_set_fixed 2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 2.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1003[0...n]
CO: Fixed speed setpoint 3 / n_set_fixed 3
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 3.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1004[0...n]
CO: Fixed speed setpoint 4 / n_set_fixed 4
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 4.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1005[0...n]
CO: Fixed speed setpoint 5 / n_set_fixed 5
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 5.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
1-134
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1006[0...n]
CO: Fixed speed setpoint 6 / n_set_fixed 6
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 6.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1007[0...n]
CO: Fixed speed setpoint 7 / n_set_fixed 7
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 7.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1008[0...n]
CO: Fixed speed setpoint 8 / n_set_fixed 8
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 8.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1009[0...n]
CO: Fixed speed setpoint 9 / n_set_fixed 9
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 9.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1010[0...n]
CO: Fixed speed setpoint 10 / n_set_fixed 10
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 10.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-135
Parameters
List of Parameters
p1011[0...n]
CO: Fixed speed setpoint 11 / n_set_fixed 11
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 11.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1012[0...n]
CO: Fixed speed setpoint 12 / n_set_fixed 12
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 12.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1013[0...n]
CO: Fixed speed setpoint 13 / n_set_fixed 13
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 13.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1014[0...n]
CO: Fixed speed setpoint 14 / n_set_fixed 14
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 14.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p1015[0...n]
CO: Fixed speed setpoint 15 / n_set_fixed 15
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets a value for the fixed speed / velocity setpoint 15.
Dependency:
Refer to: p1020, p1021, p1022, p1023, r1024, r1197
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
1-136
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1016
Description:
Value:
Note:
p1020[0...n]
Fixed speed setpoint mode / n_setp_fixed mode
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2
Factory setting
1
Sets the mode to select the fixed speed setpoint.
1:
Direct selection
2:
Selection binary coded
Re p1016 = 1:
In this mode, the fixed speed setpoint is entered using p1001 ... p1004.
Re p1016 = 2:
In this mode, the fixed speed setpoint is entered using p1001 ... p1015.
BI: Fixed speed setpoint selection Bit 0 / n_set_fixed Bit 0
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for selecting the fixed speed setpoint.
Dependency:
Selects the required fixed speed setpoint using p1020 ... p1023.
Factory setting
0
Displays the number of the actual fixed speed setpoint in r1197.
Sets the values for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1021, p1022, p1023, r1197
Note:
p1021[0...n]
Description:
Dependency:
Note:
p1022[0...n]
Description:
Dependency:
Note:
If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
BI: Fixed speed setpoint selection Bit 1 / n_set_fixed Bit 1
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for selecting the fixed speed setpoint.
Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets the values for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1020, p1022, p1023, r1197
If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
BI: Fixed speed setpoint selection Bit 2 / n_set_fixed Bit 2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for selecting the fixed speed setpoint.
Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets the values for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1020, p1021, p1023, r1197
If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-137
Parameters
List of Parameters
p1023[0...n]
BI: Fixed speed setpoint selection Bit 3 / n_set_fixed Bit 3
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for selecting the fixed speed setpoint.
Dependency:
Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets the values for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1020, p1021, p1022, r1197
Note:
If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
r1024
CO: Fixed speed setpoint effective / n_set_fixed eff
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the selected and effective fixed speed setpoint.
This setpoint is the output value for the fixed speed setpoints and must be appropriately interconnected (e.g. with
the main setpoint).
Dependency:
Selects the required fixed speed setpoint using p1020 ... p1023.
Displays the number of the actual fixed speed setpoint in r1197.
Sets the values for the fixed speed setpoints 1 ... 15 using p1001 ... p1015.
Refer to: p1070, r1197
Note:
If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
r1025.0
BO: Fixed speed setpoint status / n_setp_fix status
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status when selecting the fixed speed setpoints.
Bit field:
Bit
00
Dependency:
Refer to: p1016
Note:
Re bit 00:
Signal name
Fixed speed setpoint selected
1 signal
Yes
0 signal
No
FP
-
When the fixed speed setpoints are directly selected (p1016 = 1), this bit is set if at least 1 fixed speed setpoint is
selected.
1-138
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1030[0...n]
Motorized potentiometer configuration / Mop configuration
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0110 bin
Description:
Sets the configuration for the motorized potentiometer.
Bit field:
Bit
00
01
02
03
04
Notice:
Signal name
Data save active
Automatic mode, ramp-function generator
active
Initial rounding-off active
Save in NVRAM active
Ramp-function generator always active
1 signal
Yes
Yes
0 signal
No
No
FP
-
Yes
Yes
Yes
No
No
No
-
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
Re bit 00:
0: The setpoint for the motorized potentiometer is not saved and after ON is entered using p1040.
1: The setpoint for the motorized potentiometer is saved after OFF and after ON set to the saved value. In order to
save in a non-volatile fashion, bit 03 should be set to 1.
Re bit 01:
0: Without ramp-function generator in the automatic mode (ramp-up/ramp-down time = 0).
1: With ramp-function generator in the automatic mode.
For manual operation (0 signal via BI: p1041), the ramp-function generator is always active.
Re bit 02:
0: Without initial rounding-off
1: With initial rounding-off. The selected ramp-up/down time is correspondingly exceeded. The initial rounding-off is
a sensitive way of specifying small changes (progressive reaction when keys are pressed).
The jerk for the initial rounding-off is independent of the ramp-up time and only depends on the selected maximum
speed (p1082). It is calculated as follows:
r = 0.01 % * p1082 [1/s] / 0.13^2 [s^2]
The jerk acts up until the maximum acceleration is reached (a_max = p1082 [1/s] / p1047 [s]), and then the drive
continues to run linearly with a constant rate of acceleration. The higher the maximum acceleration (the lower that
p1047 is), the longer the ramp-up time increases with respect to the set ramp-up time.
Re bit 03:
0: Non-volatile data save de-activated.
1: The setpoint for the motorized potentiometer is saved in a non-volatile fashion (for bit 00 = 1).
Re bit 04:
When the bit is set, the ramp-function generator is computed independent of the pulse enable. The actual output
value of the motorized potentiometer is always in r1050.
p1035[0...n]
BI: Motorized potentiometer setpoint raise / Mop raise
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
0
Sets the signal source to continually increase the setpoint for the motorized potentiometer.
The setpoint change (CO: r1050) depends on the set ramp-up time (p1047) and the duration of the signal that is
present (BI: p1035).
Dependency:
Refer to: p1036
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-139
Parameters
List of Parameters
p1035[0...n]
BI: Motorized potentiometer setpoint raise / Mop raise
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.13
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source to continually increase the setpoint for the motorized potentiometer.
The setpoint change (CO: r1050) depends on the set ramp-up time (p1047) and the duration of the signal that is
present (BI: p1035).
Dependency:
Refer to: p1036
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1036[0...n]
BI: Motorized potentiometer lower setpoint / Mop lower
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
0
Sets the signal source to continuously lower the setpoint for the motorized potentiometer.
The setpoint change (CO: r1050) depends on the set ramp-down time (p1048) and the duration of the signal that is
present (BI: p1036).
Dependency:
Refer to: p1035
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1036[0...n]
BI: Motorized potentiometer lower setpoint / Mop lower
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.14
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source to continuously lower the setpoint for the motorized potentiometer.
The setpoint change (CO: r1050) depends on the set ramp-down time (p1048) and the duration of the signal that is
present (BI: p1036).
Dependency:
Refer to: p1035
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1037[0...n]
Motorized potentiometer maximum speed / MotP n_max
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Description:
Sets the maximum speed/velocity for the motorized potentiometer.
Note:
This parameter is automatically pre-assigned in the commissioning phase.
Factory setting
0.000 [rpm]
The setpoint output from the motorized potentiometer is limited to this value (see function diagram 3020).
1-140
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1038[0...n]
Motorized potentiometer minimum speed / MotP n_min
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Description:
Sets the minimum speed/velocity for the motorized potentiometer.
Note:
This parameter is automatically pre-assigned in the commissioning phase.
Factory setting
0.000 [rpm]
The setpoint output from the motorized potentiometer is limited to this value (see function diagram 3020).
p1039[0...n]
BI: Motorized potentiometer inversion / MotP inv
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to invert the minimum speed/velocity or the maximum speed/velocity for the motorized
potentiometer.
Dependency:
Refer to: p1037, p1038
Note:
The inversion is only active during "motorized potentiometer raise" or "motorized potentiometer lower".
p1040[0...n]
Motorized potentiometer starting value / Mop start value
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets the starting value for the motorized potentiometer. This starting value becomes effective after the drive has
been powered up.
Dependency:
Only effective if p1030.0 = 0.
Refer to: p1030
p1041[0...n]
Description:
BI: Motorized potentiometer manual/automatic / Mop manual/auto
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source to change over from manual to automatic when using a motorized potentiometer.
In the manual mode, the setpoint is changed using two signals - raise and lower. In the automatic mode, the setpoint must be interconnected via a connector input.
Dependency:
Refer to: p1030, p1035, p1036, p1042
Note:
The effectiveness of the internal ramp-function generator can be set in automatic mode.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-141
Parameters
List of Parameters
p1042[0...n]
CI: Motorized potentiometer automatic setpoint / Mop auto setpoint
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the setpoint of the motorized potentiometer in the automatic mode.
Dependency:
Refer to: p1041
p1043[0...n]
BI: Motorized potentiometer accept setting value / MotP acc set val
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Dependency:
Note:
Sets the signal source to accept the setting value for the motorized potentiometer.
Refer to: p1044
The setting value (CI: p1044) becomes effective for a 0/1 edge of the setting command (BI: p1043).
p1044[0...n]
CI: Motorized potentiometer setting value / Mop set val
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Dependency:
Note:
Sets the signal source for the setting value for the motorized potentiometer.
Refer to: p1043
The setting value (CI: p1044) becomes effective for a 0/1 edge of the setting command (BI: p1043).
r1045
CO: Mot. potentiometer speed setp. in front of ramp-fct. gen. / Mop n_set bef RFG
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Sets the effective setpoint in front of the internal motorized potentiometer ramp-function generator.
p1047[0...n]
Motorized potentiometer ramp-up time / Mop ramp-up time
Description:
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
1000.000 [s]
Factory setting
10.000 [s]
Sets the ramp-up time for the internal ramp-function generator for the motorized potentiometer.
The setpoint is changed from zero up to the speed/velocity limit (p1082) within this time (if no initial rounding-off has
been activated).
Dependency:
Refer to: p1030, p1048, p1082
Note:
When the initial rounding-off is activated (p1030.2) the ramp-up time is correspondingly extended.
1-142
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1048[0...n]
Description:
Motorized potentiometer ramp-down time / Mop ramp-down time
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
1000.000 [s]
Factory setting
10.000 [s]
Sets the ramp-down time for the internal ramp-function generator for the motorized potentiometer.
The setpoint is changed from the speed/velocity limit (p1082) to zero within this time (if no initial rounding-off has
been activated).
Dependency:
Refer to: p1030, p1047, p1082
Note:
The deceleration time is extended corresponding to the activated initial rounding-off (p1030.2).
r1050
CO: Motor. potentiometer setpoint after the ramp-function generator /
Mop setp after RFG
Description:
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Sets the effective setpoint after the internal motorized potentiometer ramp-function generator.
This setpoint is the output value of the motorized potentiometer and must be appropriately interconnected onwards
(e.g. with the main setpoint).
Dependency:
Refer to: p1070
Note:
For "With ramp-function generator", after an OFF1, OFF2, OFF3 or for a 0 signal via BI: p0852 (inhibit operation,
cancel pulses) the ramp-function generator output (r1050) is set to the starting value (configuration via p1030.0).
p1051[0...n]
CI: Speed limit RFG positive direction of rotation / n_limit RFG pos
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
CU240B-2 DP
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
CU240E-2
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP
Factory setting
1083[0]
Description:
Sets the signal source for the speed limit of the positive direction on the ramp-function generator input.
p1051[0...n]
CI: Speed limit RFG positive direction of rotation / n_limit RFG pos
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
CU240E-2 F
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
9733[0]
Sets the signal source for the speed limit of the positive direction on the ramp-function generator input.
p1052[0...n]
CI: Speed limit RFG negative direction of rotation / n_limit RFG neg
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
CU240B-2 DP
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
CU240E-2
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP
Description:
Factory setting
1086[0]
Sets the signal source for the speed limit of the negative direction on the ramp-function generator input.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-143
Parameters
List of Parameters
p1052[0...n]
CI: Speed limit RFG negative direction of rotation / n_limit RFG neg
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
CU240E-2 F
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
9733[1]
Sets the signal source for the speed limit of the negative direction on the ramp-function generator input.
p1055[0...n]
BI: Jog bit 0 / Jog bit 0
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for jog 1.
Dependency:
Refer to: p0840, p1058
Notice:
The drive is enabled for jogging using BI: p1055 or BI: p1056.
Factory setting
0
The command "ON/OFF1" can be issued using BI: p0840 or using BI: p1055/p1056.
Only the signal source that was used to power up can also be used to power down again.
p1055[0...n]
BI: Jog bit 0 / Jog bit 0
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 0
[1] 722.0
[2] 0
[3] 0
Description:
Sets the signal source for jog 1.
Dependency:
Refer to: p0840, p1058
Notice:
The drive is enabled for jogging using BI: p1055 or BI: p1056.
The command "ON/OFF1" can be issued using BI: p0840 or using BI: p1055/p1056.
Only the signal source that was used to power up can also be used to power down again.
p1056[0...n]
BI: Jog bit 1 / Jog bit 1
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for jog 2.
Dependency:
Refer to: p0840, p1059
Notice:
The drive is enabled for jogging using BI: p1055 or BI: p1056.
Factory setting
0
The command "ON/OFF1" can be issued using BI: p0840 or using BI: p1055/p1056.
Only the signal source that was used to power up can also be used to power down again.
1-144
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1056[0...n]
BI: Jog bit 1 / Jog bit 1
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 0
[1] 722.1
[2] 0
[3] 0
Description:
Sets the signal source for jog 2.
Dependency:
Refer to: p0840, p1059
Notice:
The drive is enabled for jogging using BI: p1055 or BI: p1056.
The command "ON/OFF1" can be issued using BI: p0840 or using BI: p1055/p1056.
Only the signal source that was used to power up can also be used to power down again.
p1058[0...n]
Jog 1 speed setpoint / Jog 1 n_set
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
150.000 [rpm]
Description:
Sets the speed/velocity for jog 1. Jogging is level-triggered and allows the motor to be incrementally moved.
Dependency:
Refer to: p1055, p1056
p1059[0...n]
Jog 2 speed setpoint / Jog 2 n_set
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
210000.000 [rpm]
Factory setting
-150.000 [rpm]
Description:
Sets the speed/velocity for jog 2. Jogging is level-triggered and allows the motor to be incrementally moved.
Dependency:
Refer to: p1055, p1056
p1063[0...n]
Speed limit setpoint channel / n_limit setp
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Description:
Sets the speed limit/velocity limit effective in the setpoint channel.
Dependency:
Refer to: p1082, p1083, p1085, p1086, p1088
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
210000.000 [rpm]
1-145
Parameters
List of Parameters
p1070[0...n]
CI: Main setpoint / Main setpoint
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
CU240E-2
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 755[0]
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source for the main setpoint.
Examples:
r1024: Fixed speed setpoint effective
r1050: Motor. potentiometer setpoint after the ramp-function generator
Dependency:
Refer to: p1071, r1073, r1078
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1070[0...n]
CI: Main setpoint / Main setpoint
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
CU240E-2 DP
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2050[1]
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source for the main setpoint.
Examples:
r1024: Fixed speed setpoint effective
r1050: Motor. potentiometer setpoint after the ramp-function generator
Dependency:
Refer to: p1071, r1073, r1078
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1071[0...n]
CI: Main setpoint scaling / Main setp scal
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for scaling the main setpoint.
r1073
CO: Main setpoint effective / Main setpoint eff
Description:
1-146
Factory setting
1
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the effective main setpoint. The value shown is the main setpoint after scaling.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1075[0...n]
CI: Suppl setpoint / Suppl setpoint
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the supplementary setpoint.
Dependency:
Refer to: p1076, r1077, r1078
p1076[0...n]
Factory setting
0
CI: Supplementary setpoint scaling / Suppl setp scal
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Description:
Sets the signal source for scaling the supplementary setpoint.
r1077
CO: Supplementary setpoint effective / Suppl setpoint eff
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the effective supplementary setpoint. The value shown is the additional setpoint after scaling.
r1078
CO: Total setpoint effective / Total setpoint eff
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the total effective setpoint. The value indicates the sum of the effective main setpoint and supplementary
setpoint.
p1080[0...n]
Minimum speed / n_min
Description:
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1), T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
19500.000 [rpm]
Factory setting
0.000 [rpm]
Sets the lowest possible motor speed.
This value is not undershot in operation.
Note:
The parameter value applies for both motor directions.
In exceptional cases, the motor can operate below this value (e.g. when reversing).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-147
Parameters
List of Parameters
p1082[0...n]
Maximum speed / n_max
Access level: 1
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: C(1), T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Factory setting
1500.000 [rpm]
Description:
Sets the highest possible speed.
Dependency:
Refer to: p0230, r0313, p0322
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
The parameter applies for both motor directions. The parameter has a limiting effect and is the reference quantity
for all ramp-up and ramp-down times (e.g. down ramps, ramp-function generator, motor potentiometer).
Since the parameter is part of quick commissioning (p0010 = 1), it is defined appropriately when p0310, p0311,
p0322, p0324, p0530, p0531, and p0532 are changed.
The following limits are always effective for p1082:
p1082 <= min(p0324, p0532) if p0324 > 0 and p0532 > 0
p1082 <= p0322 if p0324 = 0 or p0532 = 0 and p0322 > 0
p1082 <= 60 x maximum(15 x r0310, 650 Hz) / r0313
p1082 <= 60 x maximum power unit pulse frequency / (k x r0313), with k = 12 (vector control), k = 6.5 (U/f control)
If a sine-wave filter (p0230 = 3) is parameterized as output filter, then the maximum speed is limited corresponding
to the maximum permissible filter output frequency (refer to the filter data sheet). For reactors and dU/dt filters, it is
limited to 120 Hz / r0313.
During automatic calculation (p0340 = 1, p3900 > 0), the parameter value is assigned the maximum motor speed
(p0322). If p0322 = 0, the rated motor speed (p0311) is used as default (pre-assignment) value. For induction
motors, the synchronous no-load speed is used as the default value (p0310 x 60 / r0313).
For synchronous motors, the following additionally applies:
During automatic calculation (p0340, p3900), p1082 is limited to speeds where the EMF does not exceed the DC
link voltage.
p1082 is also available in the quick commissioning (p0010 = 1); this means that when exiting via p3900 > 0, the
value is not changed.
For vector control, the maximum speed is restricted to 60.0 / (8.333 x 500 µs x r0313). This can be identified by a
reduction in r1084. p1082 is not changed in this process due to the fact that the operating mode p1300 can be
changed over.
When using sine-wave filters (p0230 = 3, 4), the maximum speed r1084 is limited to 70% of the resonant frequency
of the filter capacitance and the motor leakage inductance.
p1083[0...n]
CO: Speed limit in positive direction of rotation / n_limit pos
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Factory setting
210000.000 [rpm]
Description:
Sets the maximum speed for the positive direction.
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
r1084
CO: Speed limit positive effective / n_limit pos eff
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the effective positive speed limit.
Dependency:
Refer to: p1082, p1083, p1085
1-148
Factory setting
- [rpm]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1085[0...n]
CI: Speed limit in positive direction of rotation / n_limit pos
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1083[0]
Description:
Sets the signal source for the speed limit of the positive direction.
p1086[0...n]
CO: Speed limit in negative direction of rotation / n_limit neg
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
-210000.000 [rpm]
Max
0.000 [rpm]
Factory setting
-210000.000 [rpm]
Description:
Sets the speed limit for the negative direction.
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
r1087
CO: Speed limit negative effective / n_limit neg eff
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the effective negative speed limit.
Dependency:
Refer to: p1082, p1086, p1088
p1088[0...n]
CI: Speed limit in negative direction of rotation / n_limit neg
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the speed/velocity limit of the negative direction.
p1091[0...n]
Skip speed 1 / n_skip 1
Factory setting
1086[0]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Description:
Sets skip speed 1.
Dependency:
Refer to: p1092, p1093, p1094, p1101
Factory setting
0.000 [rpm]
Notice:
Skip bandwidths can also become ineffective as a result of the downstream limits in the setpoint channel.
Note:
The skip (suppression) speeds can be used to prevent the effects of mechanical resonance.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-149
Parameters
List of Parameters
p1092[0...n]
Skip speed 2 / n_skip 2
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets skip speed 2.
Dependency:
Refer to: p1091, p1093, p1094, p1101
Notice:
Skip bandwidths can also become ineffective as a result of the downstream limits in the setpoint channel.
p1093[0...n]
Skip speed 3 / n_skip 3
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets skip speed 3.
Dependency:
Refer to: p1091, p1092, p1094, p1101
Notice:
Skip bandwidths can also become ineffective as a result of the downstream limits in the setpoint channel.
p1094[0...n]
Skip speed 4 / n_skip 4
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets skip speed 4.
Dependency:
Refer to: p1091, p1092, p1093, p1101
Notice:
Skip bandwidths can also become ineffective as a result of the downstream limits in the setpoint channel.
p1101[0...n]
Skip speed bandwidth / n_skip bandwidth
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
210000.000 [rpm]
Factory setting
0.000 [rpm]
Description:
Sets the bandwidth for the skip speeds/velocities 1 to 4.
Dependency:
Refer to: p1091, p1092, p1093, p1094
Note:
The setpoint (reference) speeds are skipped (suppressed) in the range of the skip speed +/-p1101.
Steady-state operation is not possible in the skipped (suppressed) speed range. The skip (suppression) range is
skipped.
Example:
p1091 = 600 and p1101 = 20
--> setpoint speeds between 580 and 620 [rpm] are skipped.
For the skip bandwidths, the following hysteresis behavior applies:
For a setpoint speed coming from below, the following applies:
r1170 < 580 [rpm] and 580 [rpm] <= r1114 <= 620 [rpm] --> r1119 = 580 [rpm]
For a setpoint speed coming from above, the following applies:
r1170 > 620 [rpm] and 580 [rpm] <= r1114 <= 620 [rpm] --> r1119 = 620 [rpm]
1-150
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1108[0...n]
BI: Total setpoint selection / Total setp sel
Access level: 4
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the total setpoint.
Dependency:
The selection of the total speed setpoint is automatically interconnected to the status word of the technology controller (r2349.4) if the technology controller is selected (p2200 > 0) and operated in the mode p2251 = 0.
Refer to: p1109
Caution:
If the technology controller is to supply the total setpoint using p1109, then it is not permissible to withdraw the interconnection to its status word (r2349.4).
p1109[0...n]
CI: Total setpoint / Total setp
Description:
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the total setpoint.
For p1108 = 1 signal, the total setpoint is read in via p1109.
Dependency:
The signal source of the total setpoint is automatically interconnected to the output of the technology controller
(r2294) if the technology controller is selected (p2200 > 0) and operated in the mode p2251 = 0.
Refer to: p1108
Caution:
p1110[0...n]
If the technology controller is to supply the total setpoint using p1109, then it is not permissible to disable the interconnection to its output (r2294).
BI: Inhibit negative direction / Inhib neg dir
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to disable the negative direction.
Dependency:
Refer to: p1111
p1111[0...n]
BI: Inhibit positive direction / Inhib pos dir
Factory setting
0
Access level: 4
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to disable the positive direction.
Dependency:
Refer to: p1110
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
0
1-151
Parameters
List of Parameters
r1112
CO: Speed setpoint after minimum limiting / n_set n. min_lim
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the speed setpoint after the minimum limiting.
Dependency:
Refer to: p1091, p1092, p1093, p1094, p1101
Factory setting
- [rpm]
p1113[0...n]
BI: Setpoint inversion / Setp inv
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 722.1
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source to invert the setpoint.
Dependency:
Refer to: r1198
Caution:
If the technology controller is being used as the speed main setpoint (p2251 = 0), do not invert the setpoint using
p1113 when the technology controller is enabled because this can cause the speed to change suddenly and lead to
positive couplings in the control loop.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1113[0...n]
BI: Setpoint inversion / Setp inv
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.11
[1] 0
[2] 0
[3] 0
Description:
Sets the signal source to invert the setpoint.
Dependency:
Refer to: r1198
Caution:
If the technology controller is being used as the speed main setpoint (p2251 = 0), do not invert the setpoint using
p1113 when the technology controller is enabled because this can cause the speed to change suddenly and lead to
positive couplings in the control loop.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
r1114
CO: Setpoint after the direction limiting / Setp after limit
Description:
1-152
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the speed/velocity setpoint after the changeover and limiting the direction.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1115
Ramp-function generator selection / RFG selection
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
1
Description:
Sets the ramp-function generator type.
Value:
0:
1:
Note:
Another ramp-function generator type can only be selected when the motor is at a standstill.
r1119
CO: Ramp-function generator setpoint at the input / RFG setp at inp
Basic ramp-function generator
Extended ramp-function generator
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the setpoint at the input of the ramp-function generator.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
The setpoint is influenced by other functions, e.g. skip (suppressed) speeds, minimum and maximum limits.
p1120[0...n]
Ramp-function generator ramp-up time / RFG ramp-up time
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
999999.000 [s]
Factory setting
10.000 [s]
Description:
The ramp-function generator ramps-up the speed setpoint from standstill (setpoint = 0) up to the maximum speed
(p1082) in this time.
Dependency:
Refer to: p1082, p1123
Note:
The parameter is adapted during the rotating measurement (p1960 > 0). This is the reason that during the rotating
measurement, the motor can accelerate faster than was originally parameterized.
For U/f control and sensorless vector control (see p1300), ramp-up times of 0 s are not expedient. The setting
should be based on the startup times (r0345) of the motor.
p1121[0...n]
Ramp-function generator ramp-down time / RFG ramp-down time
PM230
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
999999.000 [s]
Description:
Factory setting
30.000 [s]
The ramp-function generator ramps-down the speed setpoint from the maximum speed (p1082) down to standstill
(setpoint = 0) in this time.
Further, the ramp-down time is always effective for OFF1.
Dependency:
The parameter is pre-assigned depending on the size of the power unit.
Refer to: p1082, p1123
Note:
For U/f control and sensorless vector control (see p1300), ramp-down times of 0 s are not recommended. The setting should be based on the startup times (r0345) of the motor.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-153
Parameters
List of Parameters
p1121[0...n]
Ramp-function generator ramp-down time / RFG ramp-down time
PM240
Access level: 1
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: C(1), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
999999.000 [s]
Description:
Factory setting
10.000 [s]
The ramp-function generator ramps-down the speed setpoint from the maximum speed (p1082) down to standstill
(setpoint = 0) in this time.
Further, the ramp-down time is always effective for OFF1.
Dependency:
Refer to: p1082, p1123
Note:
For U/f control and sensorless vector control (see p1300), ramp-down times of 0 s are not recommended. The setting should be based on the startup times (r0345) of the motor.
p1122[0...n]
BI: Bypass ramp-function generator / Bypass RFG
Access level: 4
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for bypassing the ramp generator (ramp-up and ramp-down times = 0).
Caution:
If the technology controller is operated in mode p2251 = 0 (technology controller as main speed setpoint), then it is
not permissible to disable the interconnection to its status word (r2349).
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
In the case of sensorless vector control, the ramp-function generator must not be bypassed, other than indirectly by
means of interconnection with r2349.
p1123[0...n]
Ramp-function generator minimum ramp-up time / RFG t_RU min
Description:
Dependency:
Note:
p1127[0...n]
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
999999.000 [s]
Factory setting
0.000 [s]
Sets the minimum ramp-up time.
The ramp-up time (p1120) is limited internally to this minimum value.
Refer to: p1082
For U/f control and sensorless vector control (see p1300), ramp-down times of 0 s are not recommended. The setting should be based on the startup times (r0345) of the motor.
If the maximum speed p1082 changes, p1123 is re-calculated.
Ramp-function generator minimum ramp-down time / RFG t_RD min
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
999999.000 [s]
Factory setting
0.000 [s]
Description:
Sets the minimum ramp-down time.
Dependency:
Refer to: p1082
Note:
For U/f control and sensorless vector control (see p1300), ramp-down times of 0 s are not recommended. The setting should be based on the startup times (r0345) of the motor. If the maximum speed p1082 changes, p1123 is recalculated.
The ramp-down time (p1121) is limited internally to this minimum value.
1-154
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1130[0...n]
Ramp-function generator initial rounding-off time / RFG t_start_round
PM230
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Factory setting
2.000 [s]
Description:
Sets the initial rounding-off time for the extended ramp generator. The value applies to ramp-up and ramp-down.
Note:
Rounding-off times avoid an abrupt response and prevent damage to the mechanical system.
p1130[0...n]
Ramp-function generator initial rounding-off time / RFG t_start_round
PM240
Access level: 2
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Factory setting
0.000 [s]
Description:
Sets the initial rounding-off time for the extended ramp generator. The value applies to ramp-up and ramp-down.
Note:
Rounding-off times avoid an abrupt response and prevent damage to the mechanical system.
p1131[0...n]
Ramp-function generator final rounding-off time / RFG t_end_delay
PM230
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Factory setting
2.000 [s]
Description:
Sets the final rounding-off time for the extended ramp generator. The value applies to ramp-up and ramp-down.
Note:
Rounding-off times avoid an abrupt response and prevent damage to the mechanical system.
p1131[0...n]
Ramp-function generator final rounding-off time / RFG t_end_delay
PM240
Access level: 2
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Factory setting
0.000 [s]
Description:
Sets the final rounding-off time for the extended ramp generator. The value applies to ramp-up and ramp-down.
Note:
Rounding-off times avoid an abrupt response and prevent damage to the mechanical system.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-155
Parameters
List of Parameters
p1134[0...n]
Ramp-function generator rounding-off type / RFG round-off type
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Sets the smoothed response to the OFF1 command or the reduced setpoint for the extended ramp-function generator.
Value:
0:
1:
Dependency:
No effect up to initial rounding-off time (p1130) > 0 s.
Note:
p1134 = 0 (continuous smoothing)
Cont. smoothing
Discont smoothing
If the setpoint is reduced while ramping-up, initially a final rounding-off is carried out and then the ramp-up completed. During the final rounding-off, the output of the ramp-function generator continues to go in the direction of the
previous setpoint (overshoot). After the final rounding-off has been completed, the output goes toward the new setpoint.
p1134 = 1 (discontinuous smoothing)
If the setpoint is reduced while ramping-up, then the output goes immediately in the direction of the new setpoint.
For the setpoint change there is no rounding-off.
p1135[0...n]
OFF3 ramp-down time / OFF3 t_RD
PM230
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
5400.000 [s]
Factory setting
30.000 [s]
Description:
Sets the ramp-down time from the maximum speed down to zero speed for the OFF3 command.
Dependency:
The parameter is pre-assigned depending on the size of the power unit.
Note:
This time can be exceeded if the DC link voltage reaches its maximum value.
p1135[0...n]
OFF3 ramp-down time / OFF3 t_RD
PM240
Access level: 2
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: C(1), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
5400.000 [s]
Factory setting
0.000 [s]
Description:
Sets the ramp-down time from the maximum speed down to zero speed for the OFF3 command.
Note:
This time can be exceeded if the DC link voltage reaches its maximum value.
p1136[0...n]
OFF3 initial rounding-off time / RFGOFF3 t_strt_rnd
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Description:
1-156
Factory setting
2.000 [s]
Sets the initial rounding-off time for OFF3 for the extended ramp generator.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1136[0...n]
OFF3 initial rounding-off time / RFGOFF3 t_strt_rnd
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Description:
p1137[0...n]
Factory setting
0.000 [s]
Sets the initial rounding-off time for OFF3 for the extended ramp generator.
OFF3 final rounding-off time / RFG OFF3 t_end_del
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
30.000 [s]
Factory setting
0.000 [s]
Description:
Sets the final rounding-off time for OFF3 for the extended ramp generator.
p1140[0...n]
BI: Enable ramp-function generator/inhibit ramp-function generator / RFG enable
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the signal source for the command "enable ramp-function generator/inhibit ramp-function generator".
For the PROFIdrive profile, this command corresponds to control word 1 bit 4 (STW1.4).
BI: p1140 = 0 signal:
Inhibits the ramp-function generator (the ramp-function generator output is set to zero).
BI: p1140 = 1 signal:
Enables the ramp-function generator.
Dependency:
Refer to: r0054, p1141, p1142
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-157
Parameters
List of Parameters
p1140[0...n]
BI: Enable ramp-function generator/inhibit ramp-function generator / RFG enable
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.4
[1] 1
[2] 2090.4
[3] 2090.4
Description:
Sets the signal source for the command "enable ramp-function generator/inhibit ramp-function generator".
For the PROFIdrive profile, this command corresponds to control word 1 bit 4 (STW1.4).
BI: p1140 = 0 signal:
Inhibits the ramp-function generator (the ramp-function generator output is set to zero).
BI: p1140 = 1 signal:
Enables the ramp-function generator.
Dependency:
Refer to: r0054, p1141, p1142
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1141[0...n]
BI: Continue ramp-function generator/freeze ramp-function generator / Continue RFG
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the signal source for the command "continue ramp-function generator/freeze ramp-function generator".
For the PROFIdrive profile, this command corresponds to control word 1 bit 5 (STW1.5).
BI: p1141 = 0 signal:
Freezes the ramp-function generator.
BI: p1141 = 1 signal:
Continues the ramp-function generator.
Dependency:
Refer to: r0054, p1140, p1142
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The ramp-function generator is, independent of the state of the signal source, active in the following cases:
- OFF1/OFF3.
- ramp-function generator output within the suppression bandwidth.
- ramp-function generator output below the minimum speed.
1-158
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1141[0...n]
BI: Continue ramp-function generator/freeze ramp-function generator / Continue RFG
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.5
[1] 1
[2] 2090.5
[3] 2090.5
Description:
Sets the signal source for the command "continue ramp-function generator/freeze ramp-function generator".
For the PROFIdrive profile, this command corresponds to control word 1 bit 5 (STW1.5).
BI: p1141 = 0 signal:
Freezes the ramp-function generator.
BI: p1141 = 1 signal:
Continues the ramp-function generator.
Dependency:
Refer to: r0054, p1140, p1142
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The ramp-function generator is, independent of the state of the signal source, active in the following cases:
- OFF1/OFF3.
- ramp-function generator output within the suppression bandwidth.
- ramp-function generator output below the minimum speed.
p1142[0...n]
BI: Enable setpoint/inhibit setpoint / Setpoint enable
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
1
Sets the signal source for the command "enable setpoint/inhibit setpoint".
For the PROFIdrive profile, this command corresponds to control word 1 bit 6 (STW1.6).
BI: p1142 = 0 signal
Inhibits the setpoint (the ramp-function generator input is set to zero).
BI: p1142 = 1 signal
Enables the setpoint.
Dependency:
Refer to: p1140, p1141
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-159
Parameters
List of Parameters
p1142[0...n]
BI: Enable setpoint/inhibit setpoint / Setpoint enable
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.6
[1] 1
[2] 2090.6
[3] 2090.6
Description:
Sets the signal source for the command "enable setpoint/inhibit setpoint".
For the PROFIdrive profile, this command corresponds to control word 1 bit 6 (STW1.6).
BI: p1142 = 0 signal
Inhibits the setpoint (the ramp-function generator input is set to zero).
BI: p1142 = 1 signal
Enables the setpoint.
Dependency:
Refer to: p1140, p1141
Caution:
When "master control from PC" is activated, this binector input is ineffective.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1143[0...n]
BI: Ramp-function generator, accept setting value / RFG accept set v
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for accepting the setting value of the ramp-function generator.
Dependency:
The signal source for the ramp-function generator setting value is set using parameters.
Refer to: p1144
Note:
0/1 signal:
The ramp-function generator output is immediately (without delay) set to the setting value of the ramp-function generator.
1 signal:
The setting value of the ramp-function generator is effective.
1/0 signal:
The input value of the ramp-function generator is effective. The ramp-function generator output is adapted to the
input value using the ramp-up time or the ramp-down time.
0 signal:
The input value of the ramp-function generator is effective.
p1144[0...n]
CI: Ramp-function generator setting value / RFG setting value
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the ramp-function generator setting value.
Dependency:
The signal source for accepting the setting value is set using parameters.
Factory setting
0
Refer to: p1143
1-160
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1145[0...n]
Description:
Ramp-function generator tracking intensity. / RFG track intens
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0
Max
50.0
Factory setting
0.0
Sets the ramp-function generator tracking.
The output value of the ramp-function generator is tracked (corrected) corresponding to the maximum possible
drive acceleration. The reference value is the deviation at the speed/velocity controller input that is necessary to
ensure that the motor accelerates at the torque/force limit.
Notice:
If ramp-function generator tracking is activated and the ramp time is set too short, this can cause unsteady acceleration.
Remedy:
- switch off ramp-function generator tracking (p1145 = 0).
- increase the ramp-up/ramp-down time (p1120, p1121).
Note:
In the U/f mode, ramp-function generator tracking is not active.
p1148[0...n]
Ramp-function gen., tolerance for ramp-up and ramp-down active / RFG tol HL/RL act
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.000 [rpm]
Max
1000.000 [rpm]
Factory setting
19.800 [rpm]
Sets the tolerance value for the status of the ramp-function generator (ramp-up active, ramp-down active).
If the input of the ramp-function generator does not change in comparison to the output by more than the entered
tolerance time, then the status bits "ramp-up active" and "ramp-down active" are not influenced.
Dependency:
Refer to: r1199
r1149
CO: Ramp-function generator, acceleration / RFG acceleration
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2007
Data set: -
Units group: 39_1
Unit selection: p0505
Min
- [rev/s²]
Max
- [rev/s²]
Factory setting
- [rev/s²]
Description:
Displays the acceleration of the ramp-function generator.
Dependency:
Refer to: p1145
r1150
CO: Ramp-function generator speed setpoint at the output / RFG n_set at outp
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the setpoint at the output of the ramp-function generator.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-161
Parameters
List of Parameters
p1155[0...n]
CI: Speed controller speed setpoint 1 / n_ctrl n_set 1
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for speed setpoint 1 of the speed controller.
Dependency:
The effectiveness of this setpoint depends on, e.g. STW1.4 and STW1.6.
Factory setting
0
The signal source of the total setpoint is automatically interconnected to the output of the technology controller
(r2294) if the technology controller is selected (p2200 > 0) and operated in the mode p2251 = 1.
Refer to: r0002, p0840, p0844, p0848, p0852, p0854, r0898, p1140, p1142, p1160, r1170
Caution:
If the technology controller is activated, then it is not permissible to withdraw the parameter interconnection.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1160[0...n]
CI: Speed controller speed setpoint 2 / n_ctrl n_set 2
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for speed setpoint 2 of the speed controller.
Dependency:
Refer to: p1155, r1170
Note:
For OFF1/OFF3, the ramp-function generator ramp is effective.
Factory setting
0
The ramp-function generator is set (to the setpoint (r1170)) and stops the drive corresponding to the ramp-down
time (p1121 or p1135). While stopping via the ramp-function generator, STW1.4 is effective (enable ramp-function
generator).
r1169
CO: Speed controller, speed setpoints 1 and 2 / n_ctrl n_set 1/2
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the speed setpoint after the addition of the speed setpoint 1 (p1155) and speed setpoint 2 (p1160).
Dependency:
Refer to: p1155, p1160
Note:
The value is only correctly displayed at r0899.2 = 1 (operation enabled).
r1170
CO: Speed controller, setpoint sum / n_ctrl setp sum
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the speed setpoint after selecting the ramp-function generator and adding the speed setpoint 1 (p1155)
and speed setpoint 2 (p1160).
Dependency:
Refer to: r1150, p1155, p1160
1-162
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1197
Fixed speed setpoint number actual / n_set_fixed No act
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the number of the selected fixed speed/velocity setpoint.
Dependency:
Refer to: p1020, p1021, p1022, p1023
Note:
If a fixed speed setpoint has not been selected (p1020 ... p1023 = 0, r1197 = 0), then r1024 = 0 (setpoint = 0).
r1198.0...15
CO/BO: Control word setpoint channel / STW setpoint chan
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the control word for the setpoint channel.
Bit field:
Bit
00
01
02
03
05
06
11
13
14
15
r1199.0...6
CO/BO: Ramp-function generator status word / RFG ZSW
Signal name
Fixed setp bit 0
Fixed setp bit 1
Fixed setp bit 2
Fixed setp bit 3
Inhibit negative direction
Inhibit positive direction
Setpoint inversion
Motorized potentiometer raise
Motorized potentiometer lower
Bypass ramp-function generator
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status word for the ramp-function generator (RFG).
Bit field:
Bit
00
01
02
03
04
05
06
Note:
Re bit 02:
Signal name
Ramp-up active
Ramp-down active
RFG active
Ramp-function generator set
Ramp-function generator held
Ramp-function generator tracking active
Maximum limit active
FP
3010
3010
3010
3010
3040
3040
3040
3020
3020
3060,
3070
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
FP
-
The bit is an OR logic operation - bit 00 and bit 01.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-163
Parameters
List of Parameters
p1200[0...n]
Description:
FlyRest oper mode / FlyRest op_mode
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
4
Factory setting
0
Sets the operating mode for flying restart.
The flying restart allows the drive converter to be powered up while the motor is still rotating. In so doing, the drive
converter output frequency is changed until the actual motor speed/velocity is found. The motor then accelerates up
to the setpoint at the ramp-function generator setting.
Value:
0:
1:
4:
Flying restart inactive
Flying restart always active (start in setpoint direction)
Flying restart always active (start only in setpoint direction)
Dependency:
A differentiation is made between flying restart for U/f control and for vector control (p1300).
Flying restart, U/f control: p1202, p1203, r1204
Flying restart, vector control: p1202, p1203, r1205
For synchronous motors, flying restart cannot be activated.
Refer to: p1201
Refer to: F07330, F07331
Notice:
The "flying restart" function must be used in cases where the motor may still be running (e.g. after a brief line supply
interruption) or is being driven by the load. The system might otherwise shut down as a result of overcurrent.
Note:
When p1200 = 1, 4: Flying restart is active after faults, OFF1, OFF2, OFF3.
When p1200 = 1: The search is made in both directions.
When p1200 = 4: The search is only made in the setpoint direction.
For U/f control (p1300 < 20), the following applies:
The speed can only be sensed for values above approx. 5 % of the rated motor speed. For lower speeds, it is
assumed that the motor is at a standstill.
If p1200 is changed during commissioning (p0010 > 0), then it is possible that the old value will no longer be able to
be set. The reason for this is that the dynamic limits of p1200 have been changed by a parameter that was set when
the drive was commissioned (e.g. p0300).
p1201[0...n]
BI: Flying restart enable signal source / Fly_res enab S_src
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to enable the "flying restart" function.
Dependency:
Refer to: p1200
Note:
Withdrawing the enable signal has the same effect as setting p1200 = 0.
1-164
Factory setting
1
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1202[0...n]
FlyRest srch curr / FlyRest I_srch
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [%]
Max
400 [%]
Description:
Factory setting
90 [%]
Sets the search current for the "flying restart" function.
The value is referred to the motor magnetizing current.
Dependency:
Refer to: r0331
Caution:
An unfavorable parameter value can result in the motor behaving in an uncontrollable fashion.
Note:
In U/f control mode, the parameter serves as a threshold value for establishing the current at the beginning of the
flying restart function. When the threshold value is reached, the prevailing search current is set dependent upon the
frequency on the basis of voltage inputs.
Reducing the search current can also improve flying restart performance (if the system moment of inertia is not very
high, for example).
p1202[0...n]
FlyRest srch curr / FlyRest I_srch
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [%]
Max
400 [%]
Description:
Factory setting
100 [%]
Sets the search current for the "flying restart" function.
The value is referred to the motor magnetizing current.
Dependency:
Refer to: r0331
Caution:
An unfavorable parameter value can result in the motor behaving in an uncontrollable fashion.
Note:
In U/f control mode, the parameter serves as a threshold value for establishing the current at the beginning of the
flying restart function. When the threshold value is reached, the prevailing search current is set dependent upon the
frequency on the basis of voltage inputs.
Reducing the search current can also improve flying restart performance (if the system moment of inertia is not very
high, for example).
p1203[0...n]
Flying restart search rate factor / FlyRst v_Srch Fact
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [%]
Max
4000 [%]
Factory setting
150 [%]
Description:
The value influences the rate at which the output frequency is changed during a flying restart . A higher value
results in a longer search time.
Caution:
An unfavorable parameter value can result in the motor behaving in an uncontrollable fashion.
For vector control, a value that is too low or too high can cause flying restart to become unstable.
Note:
The parameter factory setting is selected so that standard induction motors that are rotating can be found and
restarted as quickly as possible (fast flying restart).
With this pre-setting, if the motor is not found (e.g. for motors that are accelerated as a result of active loads or with
U/f control and low speeds), we recommend that the search rate is reduced (by increasing p1203).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-165
Parameters
List of Parameters
p1203[0...n]
Flying restart search rate factor / FlyRst v_Srch Fact
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [%]
Max
4000 [%]
Factory setting
100 [%]
Description:
The value influences the rate at which the output frequency is changed during a flying restart . A higher value
results in a longer search time.
Caution:
An unfavorable parameter value can result in the motor behaving in an uncontrollable fashion.
For vector control, a value that is too low or too high can cause flying restart to become unstable.
Note:
The parameter factory setting is selected so that standard induction motors that are rotating can be found and
restarted as quickly as possible (fast flying restart).
With this pre-setting, if the motor is not found (e.g. for motors that are accelerated as a result of active loads or with
U/f control and low speeds), we recommend that the search rate is reduced (by increasing p1203).
r1204.0...13
CO/BO: Flying restart, U/f control status / FlyRest Uf st
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status for checking and monitoring flying restart states in the U/f control mode.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
1-166
Signal name
Current impressed
No current flow
Voltage input
Voltage reduced
Start ramp-function generator
Wait for execution
Slope filter act
Positive gradient
Current < thresh
Current minimum
Search in the positive direction
Stop after positive direction
Stop after negative direction
No result
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
No
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1205.0...15
CO/BO: Flying restart, vector control status / FlyRest vector st
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status for checking and monitoring flying restart states in the vector control mode.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Note:
Re bit 00 ... 09:
Signal name
Speed adaptation circuit record angle
Speed adaptation circuit set gain to 0
Isd channel enable
Speed control switched out
Quadrature arm switched in
Special transformation active
Speed adaptation circuit set I comp to 0
Current control on
Isd_set = 0 A
Frequency held
Search in the positive direction
Search Started
Current impressed
Search interrupted
Speed adaptation circuit deviation = 0
Speed control activated
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
FP
-
Used to control internal sequences during the flying restart.
Depending on the motor type (p0300), the number of active bits differs.
Re bits 10 ... 15:
Are used to monitor the flying restart sequence.
For permanent-magnet synchronous motors (PEM) only bits 10, 11 and 15 are supported.
p1206[0...9]
Set the fault number without automatic restart / Fault_No w/o AR
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Description:
Selects the faults for which automatic restart should not be effective.
Dependency:
The setting is only effective for p1210 = 6, 16.
Factory setting
0
Refer to: p1210
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-167
Parameters
List of Parameters
p1210
Description:
Automatic restart, mode / AR mode
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
26
Factory setting
0
Sets the automatic restart mode (AR).
The parameters must be saved in the non-volatile memory p0971 = 1 in order that the setting becomes effective.
Value:
0:
1:
4:
6:
14:
16:
26:
Inhibit automatic restart
Acknowledge all faults without restarting
Restart after line supply failure w/o additional start attempts
Restart after fault with additional start attempts
Restart after line supply failure following man. acknowledgment
Restart after fault following manual acknowledgment
Acknowledging all faults and reclosing for an ON command
Dependency:
The automatic restart requires an active ON command (e.g., via a digital input). If, for p1210 > 1, there is no active
ON command, then the automatic restart is interrupted.
When using an Operator Panel in the LOCAL mode, then there is no automatic start.
For p1210 = 14, 16, a manual acknowledgement is required for an automatic restart.
For p1210 = 26, the ON command can also be entered with a delay. After the line supply returns or acknowledging
a fault, the restart waits for an ON command. The maximum wait time is specified using p1213[0].
Refer to: p0840, p0857
Refer to: F30003
Danger:
If the automatic restart is activated (p1210 > 1) if there is an ON command (refer to p0840), the drive is powered up
as soon as any fault messages that are present can be acknowledged. This also occurs after the line supply returns
or the Control Unit boots if the DC link voltage is present again. This automatic power-up sequence can only be
interrupted by withdrawing the ON command.
Caution:
A change is only accepted and made in the state "initialization" (r1214.0) and "wait for alarm" (r1214.1). When faults
are present, therefore, the parameter cannot be changed.
For p1210 > 1, the motor is automatically started.
Note:
Re p1210 = 1:
Faults that are present are automatically acknowledged. If new faults occur after a successful fault acknowledgment, then these are also automatically acknowledged again. p1211 has no influence on the number of acknowledgment attempts.
Re p1210 = 4:
An automatic restart is only performed if fault F30003 has occurred on the power unit. If additional faults are present, then these faults are also acknowledged and when successful, starting continues. If the 24 V Control Unit
power supply fails, then this is interpreted as a line supply failure.
Re p1210 = 6:
An automatic restart is carried out if any fault has occurred.
Re p1210 = 14:
As for p1210 = 4. However, faults that are present must be manually acknowledged.
Re p1210 = 16:
As for p1210 = 6. However, faults that are present must be manually acknowledged.
Re p1210 = 26:
As for p1210 = 6. However, at the time that the fault is acknowledged or at power on, a switch-on command is not
necessary. This can be set with a time delay. The drive is switched-on again as soon as the switch-on command is
set. The restart can be interrupted with either OFF2 or OFF3.
1-168
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1211
Automatic restart, start attempts / AR start attempts
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
10
Factory setting
3
Description:
Sets the start attempts of the automatic restart function for p1210 = 4, 6, 14, 16, 26.
Dependency:
Refer to: p1210, r1214
Refer to: F07320
Caution:
A change is only accepted and made in the state "initialization" (r1214.0) and "wait for alarm" (r1214.1).
Notice:
After fault F07320 occurs, the power-on command must be withdrawn and all of the faults acknowledged so that the
automatic restart function is re-activated.
After a complete power failure the start counter always starts with the counter value that applied before the power
failure, and decrements this start attempt by 1. If a further attempt to acknowledge is started by the automatic
restart function prior to power failure, e.g. when the CU remains active on power failure longer than the time p1212
/ 2, the fault counter will already have been decremented once. In this case, the start counter is thus decreased by
the value 2.
Note:
A start attempt starts immediately when a fault occurs. The start attempt is considered to been completed if the
motor was magnetized (r0056.4 = 1) and an additional delay time of 1 s has expired.
As long as a fault is present, an acknowledge command is generated in the time intervals of p1212 / 2. When successfully acknowledged, the start counter is decremented. If, after this, a fault re-occurs before a restart has been
completed, then acknowledgement starts again from the beginning.
Fault F07320 is output if, after several faults occur, the number of parameterized start attempts has been reached.
After a successful start attempt, i.e. a fault/error has no longer occurred up to the end of the magnetizing phase, the
start counter is again reset to the parameter value after 1 s. If a fault re-occurs - the parameterized number of start
attempts is again available.
At least one start attempt is always carried out.
After a line supply failure, acknowledgement is immediate and when the line supply returns, the system is powered
up. If, between successfully acknowledging the line fault and the line supply returning, another fault occurs, then its
acknowledgement also causes the start counter to be decremented.
For p1210 = 26, the start counter is decremented if after a successful fault acknowledgement, the on command is
present.
p1212
Automatic restart, delay time start attempts / AR t_wait start
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.1 [s]
Max
1000.0 [s]
Description:
Sets the delay time up to restart.
Dependency:
This parameter setting is active for p1210 = 4, 6, 26.
Factory setting
1.0 [s]
For p1210 = 1, the following applies: Faults are only automatically acknowledged in half of the delay time, no
restart.
Refer to: p1210, r1214
Caution:
A change is only accepted and made in the state "initialization" (r1214.0) and "wait for alarm" (r1214.1).
Note:
The faults are automatically acknowledged after half of the delay time has expired and the full delay time.
If the cause of a fault is not removed in the first half of the delay time, then it is no longer possible to acknowledge in
the delay time.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-169
Parameters
List of Parameters
p1213[0...1]
Automatic restart, monitoring time / AR t_monitoring
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [s]
Max
10000.0 [s]
Factory setting
[0] 60.0 [s]
[1] 0.0 [s]
Description:
Sets the monitoring time of the automatic restart (AR).
Index:
[0] = For restart
[1] = To reset the start counter
Dependency:
Refer to: p1210, r1214
Caution:
A change is only accepted and made in the state "initialization" (r1214.0) and "wait for alarm" (r1214.1).
Notice:
After fault F07320 occurs, the power-on command must be withdrawn and all of the faults acknowledged so that the
automatic restart function is re-activated.
Note:
Index 0:
The monitoring time starts when the faults are detected. If the automatic acknowledgements are not successful, the
monitoring time runs again. If, after the monitoring time has expired, the drive has still not successfully started again
(flying restart and magnetizing of the motor must have been completed: r0056.4 = 1), then fault F07320 is output.
The monitoring is de-activated with p1213 = 0. If p1213 is set lower than the sum of p1212, the magnetizing time
p0346 and the additional delay time due to the flying restart, then fault F07320 is generated at each restart. If, for
p1210 = 1, the time in p1213 is set lower than in p1212, then fault F07320 is also generated at each restart.
The monitoring time must be extended if the faults that occur cannot be immediately and successfully acknowledged (e.g. for faults that are permanently present).
In the case of p1210 = 14, 16, the faults which are present must be acknowledged manually within the time in
p1213 index 0. Otherwise, fault F07320 is generated after the set time.
Index 1:
The start counter (refer to r1214) is only set back to the starting value p1211 if, after successful restart, the time in
p1213 index 1 has expired. The delay time is not effective for fault acknowledgement without automatic restart
(p1210 = 1). After a power failure (blackout) the delay time only starts after the line supply returns and the Control
Unit boots. The start counter is set to p1211, if F07320 occurred, the power-on command is withdrawn and the fault
is acknowledged.
The start counter is immediately updated if the starting value p1211 or the mode p1210 is changed.
For p1210 = 26, the fault must have been successfully acknowledged and the switch-on command issued within the
time in p1213, index 0. Otherwise, fault F07320 is generated after the set time.
1-170
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1214.0...15
CO/BO: Automatic restart, status / AR status
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status of the automatic restart (AR).
Bit field:
Bit
00
01
02
03
04
05
06
07
10
12
13
14
15
Note:
Signal name
Initialization
Wait for alarm
Auto restart act
Setting the acknowledgement command
Acknowledge alarms
Restart
Delay time running after automatic powerup
Fault
Effective fault
Start count. bit 0
Start count. bit 1
Start count. bit 2
Start count. bit 3
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
FP
-
Yes
Yes
ON
ON
ON
ON
No
No
OFF
OFF
OFF
OFF
-
Re bit 00:
State to display the single initialization after POWER ON.
Re bit 01:
State in which the automatic restart function waits for faults (initial state).
Re bit 02:
General display that a fault has been identified and that the restart or acknowledgement has been initiated.
Re bit 03:
Displays the acknowledge command within the "acknowledge alarms" state (bit 4 = 1). For bit 5 = 1 or bit 6 = 1, the
acknowledge command is continually displayed.
Re bit 04:
State in which the faults that are present are acknowledged. The state is exited again after successful acknowledgement. A change is only made into the next state if it is signaled that a fault is no longer present after an
acknowledgement command (bit 3 = 1).
Re bit 05:
State in which the drive is automatically powered up (only for p1210 = 4, 6).
Re bit 06:
State in which the system waits after having been powered up, to the end of the start attempt (to the end of the
magnetizing process).
For p1210 = 1, this signal is directly set after the faults have been successfully acknowledged.
Re bit 07:
State which is assumed after a fault occurs within the automatic restart function. This is only reset after acknowledging the fault and withdrawing the power-on command.
Re bit 10:
When the automatic restart function is active, r1214 bit 7 is displayed, otherwise the effective fault r2139 bit 3.
Re bits 12 ... 15:
Actual state of the start counter (binary coded).
In addition to bit 04:
For p1210 = 26, the system waits in this state until the switch-on command is available.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-171
Parameters
List of Parameters
p1215
Motor holding brake configuration / Brake config
PM230
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Description:
Sets the holding brake configuration.
Value:
0:
3:
Dependency:
Refer to: p1216, p1217, p1226, p1227, p1228
Caution:
For the setting p1215 = 0, if a brake is used, it remains closed. If the motor moves, this will destroy the brake.
Notice:
If p1215 was set to 3, then when the pulses are suppressed, the brake is closed even if the motor is still rotating.
Pulse suppression can either be caused by a 0 signal at p0844, p0845 or p0852 or as a result of a fault with OFF2
response. If this is not desirable (e.g. for a flying restart), then the brake can be kept open using a 1 signal at p0855.
Note:
if an external motor holding brake is being used, then p1215 should be set to 3 and r0899.12 should be interconnected as control signal.
No motor holding brake being used
Motor holding brake like sequence control, connection via BICO
The parameter can only be set to zero when the pulses are inhibited.
p1215
Motor holding brake configuration / Brake config
PM240
Access level: 2
Calculated: -
Data type: Integer16
PM250, PM260
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Description:
Sets the holding brake configuration.
Value:
0:
1:
2:
3:
Dependency:
Refer to: p1216, p1217, p1226, p1227, p1228
Caution:
For the setting p1215 = 0, if a brake is used, it remains closed. If the motor moves, this will destroy the brake.
Notice:
If p1215 was set to 1 or if p1215 was set to 3, then when the pulses are suppressed, the brake is closed even if the
motor is still rotating. Pulse suppression can either be caused by a 0 signal at p0844, p0845 or p0852 or as a result
of a fault with OFF2 response. If this is not desirable (e.g. for a flying restart), then the brake can be kept open using
a 1 signal at p0855.
Note:
If a holding brake integrated in the motor is used, then it is not permissible that p1215 is set to 3.
No motor holding brake being used
Motor holding brake acc. to sequence control
Motor holding brake always open
Motor holding brake like sequence control, connection via BICO
if an external motor holding brake is being used, then p1215 should be set to 3 and r0899.12 should be interconnected as control signal.
The parameter can only be set to zero when the pulses are inhibited.
p1216
Description:
Motor holding brake, opening time / Brake t_open
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
100 [ms]
Sets the time to open the motor holding brake.
After the holding brake has been controlled (opened), the speed setpoint remains at zero for this time. After this, the
speed setpoint is enabled.
Dependency:
1-172
Refer to: p1215, p1217
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1217
Description:
Motor holding brake closing time / Brake t_close
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
100 [ms]
Sets the time to apply the motor holding brake.
After OFF1 or OFF3 and the controlling (closing) of the holding brake, the drive remains stationary under closedloop control for this time with a speed setpoint of zero. The pulses are suppressed when the time expires.
Dependency:
Refer to: p1215, p1216
Notice:
If the selected closing time is too short with respect to the actual closing time of the brake, then the load can sag.
If the closing time is selected to be too long with respect to the actual closing time of the brake, the control works
against the brake and therefore reduces its lifetime.
p1226[0...n]
Description:
Threshold for zero speed detection / n_standst n_thresh
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
20.00 [rpm]
Sets the speed threshold for the standstill identification.
Acts on the actual value and setpoint monitoring.
When braking with OFF1 or OFF3, when the threshold is undershot, standstill is identified.
Dependency:
Refer to: p1227
Note:
Standstill is identified in the following cases:
- the speed actual value falls below the speed threshold in p1226 and the time started after this in p1228 has
expired.
- the speed setpoint falls below the speed threshold in p1226 and the time started after this in p1227 has expired.
The actual value sensing is subject to measuring noise. For this reason, standstill cannot be detected if the speed
threshold is too low.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-173
Parameters
List of Parameters
p1227
Description:
Zero speed detection monitoring time / n_standst t_monit
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [s]
Max
300.000 [s]
Factory setting
300.000 [s]
Sets the monitoring time for the standstill identification.
When braking with OFF1 or OFF3, standstill is identified after this time has expired, after the setpoint speed has
fallen below p1226 (also refer to p1145).
Dependency:
The parameter is pre-assigned depending on the size of the power unit.
Refer to: p1226
Notice:
For p1145 > 0.0 (RFG tracking) the setpoint is not equal to zero dependent on the selected value. This can therefore cause the monitoring time in p1227 to be exceeded. In this case, for a driven motor, the pulses are not suppressed.
Note:
Standstill is identified in the following cases:
- the speed actual value falls below the speed threshold in p1226 and the time started after this in p1228 has
expired.
- the speed setpoint falls below the speed threshold in p1226 and the time started after this in p1227 has expired.
For p1227 = 300.000 s, the following applies:
Monitoring is de-activated.
For p1227 = 0.000 s, the following applies:
With OFF1 or OFF3 and a ramp-down time = 0, the pulses are immediately suppressed and the motor "coasts"
down.
Once the Control Unit has been booted up for the first time or if the factory settings have been defined accordingly,
the parameter is defined in accordance with the power unit.
p1228
Description:
Pulse suppression delay time / Pulse suppr t_del
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [s]
Max
299.000 [s]
Factory setting
0.010 [s]
Sets the delay time for pulse suppression.
After OFF1 or OFF3 and zero speed detection, the system waits for this time to expire and the pulses are then suppressed.
Dependency:
Refer to: p1226, p1227
Notice:
If the motor holding brake is activated, the pulse suppression is only conducted if this delay time (p1228) and then
the closing time for the brake (p1217) have elapsed.
Note:
Standstill is identified in the following cases:
- the speed actual value falls below the speed threshold in p1226 and the time started after this in p1228 has
expired.
- the speed setpoint falls below the speed threshold in p1226 and the time started after this in p1227 has expired.
p1230[0...n]
Description:
Dependency:
Note:
1-174
BI: DC braking activation / DC brake act
Access level: 2
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source to activate DC braking.
Refer to: p1231, p1232, p1233, p1234, r1239
1 signal: DC braking activated.
0 signal: DC braking de-activated.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1231[0...n]
DC braking configuration / DCBRK config
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0
Max
14
Description:
Setting to activate DC braking.
Value:
0:
4:
5:
14:
Dependency:
Refer to: p0300, p1232, p1233, p1234, r1239
Note:
The function is activated as soon as the activation criterion is fulfilled.
Factory setting
0
No function
DC braking
DC braking for OFF1/OFF3
DC braking below starting speed
- the function can be initiated by an OFF2 response.
Activation criterion (one of the following criteria is fulfilled):
- binector input p1230 = 1 signal (DC braking activation).
- the drive is not in the state "S4: Operation" or in "S5x" (refer to function chart 2610).
- the internal pulse enable is missing (r0046.19 = 0).
The function can only be used for induction motors (p0300 = 1).
DC braking can only be withdrawn (p1231 = 0) if it is not being used as a fault response in p2101.
Re p1231 = 5:
DC braking can only be set for induction motors.
DC braking is activated if the OFF1 or OFF3 command is present. Binector input p1230 is ineffective. If the drive
speed still lies above the speed threshold p1234, then initially, the drive is ramped-down to this threshold, demagnetized (see p0347) and is then switched into DC braking for the time set in p1233. After this, the drive is switchedoff. If, at OFF1, the drive speed is below p1234, then it is immediately demagnetized and switched into DC braking.
A change is made into normal operation if the OFF1 command is withdrawn prematurely. Flying restart must be
activated if the motor is still rotating.
DC braking by means of fault response continues to be possible.
Re p1231 = 14:
In addition to the function for p1231 = 5, binector input p1230 is evaluated.
DC braking is only automatically activated when the speed threshold p1234 is fallen below if binector input p1230 =
1 signal.
Notice:
This is also the case, if no OFF command is present. After demagnetization and after the time in p1233 has expired,
the drive changes back into normal operation or is switched-off (for OFF1/OFF3).
If a 0 signal is applied to binector input p1230, for OFF1 and OFF3 no DC braking is executed.
Note:
DCBRK: DC Braking
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-175
Parameters
List of Parameters
p1232[0...n]
DC braking, braking current / DCBRK I_brake
Access level: 2
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
Description:
Sets the braking current for DC braking.
Dependency:
Refer to: p1230, p1231, p1233, p1234, r1239, p1345, p1346
Note:
A change to the braking current becomes effective the next time that DC braking is switched-on.
The value for p1232 is specified as an rms value in the 3-phase system. The magnitude of the braking current is the
same as that of an identical output current at frequency zero (see r0067, r0068, p0640). The braking current is
internally limited to r0067.
For vector control, a current value of 1.4142 x p1232 is obtained in the output phase U. For U/f control, the phase
angle is offset by -30 degrees to obtain a current measurement of 1.2247 x p1232 in output phase U.
For the current controller, the settings of parameters p1345 and p1346 (I_max limiting controller) are used.
p1233[0...n]
DC braking time / DCBRK time
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.0 [s]
Max
3600.0 [s]
Description:
Sets the DC braking time (as fault response).
Dependency:
Refer to: p1230, p1231, p1232, p1234, r1239
p1234[0...n]
Description:
Factory setting
1.0 [s]
Speed at the start of DC braking / DCBRK n_start
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
210000.00 [rpm]
Sets the starting speed for DC braking.
If the actual speed falls below this threshold, then DC braking is activated.
Dependency:
Refer to: p1230, p1231, p1232, p1233, r1239
r1239.8...13
CO/BO: DC braking status word / DCBRK ZSW
Access level: 2
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Status word of the DC braking.
Bit field:
Bit
08
10
11
12
13
Dependency:
Refer to: p1231, p1232, p1233, p1234
Note:
Re bit 12, 13:
Signal name
DC braking active
DC braking ready
DC braking selected
DC braking selection internally inhibited
DC braking for OFF1/OFF3
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
FP
7017
7017
-
Only effective for p1231 = 14.
1-176
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1240[0...n]
Vdc controller or Vdc monitoring configuration (vector control) / Vdc_ctr config vec
PM230
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
1
Description:
Sets the controller configuration of the DC link voltage (Vdc controller) in the closed-loop control mode. For U/f control: see p1280.
Value:
0:
1:
3:
Dependency:
Refer to: p1245
Inhib Vdc ctrl
Vdc_max controller enable
Vdc_min controller and Vdc_max controller enable
Refer to: A07400, A07401, A07402, F07405, F07406
Notice:
An excessively high value in p1245 can possibly negatively influence the normal operation of the drive.
Note:
p1240 = 1, 3:
When the DC link voltage limit specified for the power unit is reached the following applies:
- the Vdc_max controller limits the regenerative energy in order that the DC link voltage is kept below the maximum
DC link voltage when braking.
- the ramp-down times are automatically increased. If overvoltage faults occur in spite of the Vdc_max controller
being active, the ramp-down time in p1121 might need to be increased.
- set the input voltage p0210 as low as possible in line with the supply voltage (in so doing avoid A07401).
p1240 = 3:
When the switch-in threshold of the Vdc_min controller is reached (p1245), the following applies:
- the Vdc_min controller limits the energy taken from the DC link in order to keep the DC link voltage above the minimum DC link voltage when accelerating.
- the motor is braked in order to use its kinetic energy to buffer the DC link.
p1240[0...n]
Vdc controller or Vdc monitoring configuration (vector control) / Vdc_ctr config vec
PM240
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
1
Description:
Sets the controller configuration of the DC link voltage (Vdc controller) in the closed-loop control mode. For U/f control: see p1280.
Value:
0:
1:
2:
3:
Dependency:
Refer to: p1245
Inhib Vdc ctrl
Vdc_max controller enable
Vdc_min controller (kinetic buffering) enable
Vdc_min controller and Vdc_max controller enable
Refer to: A07400, A07401, A07402, F07405, F07406
Notice:
An excessively high value in p1245 can possibly negatively influence the normal operation of the drive.
Note:
p1240 = 1, 3:
When the DC link voltage limit specified for the power unit is reached the following applies:
- the Vdc_max controller limits the regenerative energy in order that the DC link voltage is kept below the maximum
DC link voltage when braking.
- the ramp-down times are automatically increased.
p1240 = 2, 3:
When the switch-in threshold of the Vdc_min controller is reached (p1245), the following applies:
- the Vdc_min controller limits the energy taken from the DC link in order to keep the DC link voltage above the minimum DC link voltage when accelerating.
- the motor is braked in order to use its kinetic energy to buffer the DC link.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-177
Parameters
List of Parameters
r1242
Vdc_max controller switch-in level / Vdc_max on_level
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Description:
Factory setting
- [V]
Displays the switch-in level for the Vdc_max controller.
If p1254 = 0 (automatic sensing of the switch-in level = off), then the following applies:
r1242 = 1.15 * sqrt(2) * V_mains = 1.15 * sqrt(2) * p0210 (supply voltage)
PM230: r1242 is limited to Vdc_max - 50.0 V.
If p1254 = 1 (automatic sensing of the switch-in level = on), then the following applies:
r1242 = Vdc_max - 50.0 V (Vdc_max: Overvoltage threshold of the power unit)
Note:
The Vdc_max controller is not switched back off until the DC-link voltage falls below the threshold 0.95 * p1242 and
the controller output is zero.
p1243[0...n]
Vdc_max controller dynamic factor / Vdc_max dyn_factor
PM230
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1 [%]
Max
10000 [%]
Description:
Factory setting
100 [%]
Sets the dynamic factor for the DC link voltage controller (Vdc_max controller).
100% means that p1250, p1251, and p1252 (gain, integral time, and rate time) are used corresponding to their
basic settings and based on a theoretical controller optimization.
If subsequent optimization is required, this can be carried out using the dynamic factor. In this case p1250, p1251,
p1252 are weighted with the dynamic factor p1243.
p1245[0...n]
Vdc_min controller switch-in level (kinetic buffering) / Vdc_min on_level
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
65 [%]
Max
150 [%]
Description:
Factory setting
73 [%]
Sets the switch-in level for the Vdc-min controller (kinetic buffering).
The value is obtained as follows:
r1246[V] = p1245[%] * sqrt(2) * p0210
Dependency:
Refer to: p0210
Warning:
An excessively high value may adversely affect normal drive operation.
1-178
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1245[0...n]
Vdc_min controller switch-in level (kinetic buffering) / Vdc_min on_level
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
65 [%]
Max
150 [%]
Description:
Factory setting
76 [%]
Sets the switch-in level for the Vdc-min controller (kinetic buffering).
The value is obtained as follows:
r1246[V] = p1245[%] * sqrt(2) * p0210
Dependency:
Refer to: p0210
Warning:
An excessively high value may adversely affect normal drive operation.
r1246
Vdc_min controller switch-in level (kinetic buffering) / Vdc_min on_level
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
Displays the switch-in level for the Vdc_min controller (kinetic buffering).
Note:
The Vdc_min controller is not switched back off until the DC-link voltage rises above the threshold 1.05 * p1246 and
the controller output is zero.
p1247[0...n]
Vdc_min controller dynamic factor (kinetic buffering) / Vdc_min dyn_factor
PM230
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1 [%]
Max
10000 [%]
Description:
Factory setting
300 [%]
Sets the dynamic factor for the Vdc_min controller (kinetic buffering).
100% means that p1250, p1251, and p1252 (gain, integral time, and rate time) are used corresponding to their
basic settings and based on a theoretical controller optimization.
If subsequent optimization is required, this can be carried out using the dynamic factor. In this case p1250, p1251,
p1252 are weighted with the dynamic factor p1247.
p1249[0...n]
Vdc_max controller speed threshold / Vdc_max n_thresh
PM230
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
10.00 [rpm]
Description:
Sets the lower speed threshold for the Vdc_max controller. When this speed threshold is undershot, the Vdc_max
control is switched out and the speed is controlled using the ramp-function generator.
Note:
For fast braking where the ramp-function generator tracking was active, it is possible to prevent the drive rotating in
the opposite direction by increasing the speed threshold and setting a final rounding-off time in the ramp-function
generator (p1131). This is supported using a dynamic setting of the speed controller.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-179
Parameters
List of Parameters
p1250[0...n]
Vdc controller proportional gain / Vdc_ctrl Kp
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
1.00
Description:
Sets the proportional gain for the DC-link voltage controller (Vdc_min controller, Vdc_max controller).
Dependency:
The effective proportional gain is obtained taking into account p1243 (Vdc_max controller dynamic factor) and the
DC link capacitance of the power unit.
p1251[0...n]
Vdc controller integral time / Vdc_ctrl Tn
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
0 [ms]
Description:
Sets the integral time for the DC-link voltage controller (Vdc_min controller, Vdc_max controller).
Dependency:
The effective integral time is obtained taking into account p1243 (Vdc_max controller dynamic factor).
Note:
p1251 = 0: The integral component is de-activated.
p1252[0...n]
Vdc controller rate time / Vdc_ctrl t_rate
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
1000 [ms]
Factory setting
0 [ms]
Description:
Sets the rate time constant for the DC-link voltage controller (Vdc_min controller, Vdc_max controller).
Dependency:
The effective rate time is obtained taking into account p1243 (Vdc_max controller dynamic factor).
p1254
Vdc_max controller automatic ON level detection / Vdc_max SenseOnLev
PM230
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Activates/de-activates the automatic sensing of the switch-in level for the Vdc_max controller.
Value:
0:
1:
p1254
Vdc_max controller automatic ON level detection / Vdc_max SenseOnLev
PM240
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Automatic detection inhibited
Automatic detection enabled
Factory setting
1
Description:
Activates/de-activates the automatic sensing of the switch-in level for the Vdc_max controller.
Value:
0:
1:
1-180
Automatic detection inhibited
Automatic detection enabled
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1255[0...n]
Vdc_min controller time threshold / Vdc_min t_thresh
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
1800.000 [s]
Description:
Factory setting
0.000 [s]
Sets the time threshold for the Vdc_min controller (kinetic buffering).
If this value is exceeded a fault is output; the required response can be parameterized.
Prerequisite: p1256 = 1
Dependency:
Refer to: F07406
Notice:
If a time threshold has been parameterized, the Vdc_max controller should also be activated (p1240 = 3) so that the
drive does not shut down with overvoltage when Vdc_min control is exited (due to the time violation) and in the
event of fault response OFF3. It is also possible to increase the OFF3 ramp-down time p1135.
p1256[0...n]
Vdc_min controller response (kinetic buffering) / Vdc_min response
PM230
Access level: 3
Calculated: -
Data type: Integer16
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Sets the response for the Vdc_min controller (kinetic buffering).
Value:
0:
1:
Dependency:
Refer to: F07405, F07406
p1257[0...n]
Vdc_min controller speed threshold / Vdc_min n_thresh
PM230
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Description:
Buffer Vdc until undervoltage, n<p1257 -> F07405
Buff. Vdc until undervolt., n<p1257 -> F07405, t>p1255 -> F07406
Factory setting
50.00 [rpm]
Sets the speed threshold for the Vdc-min controller (kinetic buffering).
If this value is exceeded a fault is output; the required response can be parameterized .
r1258
CO: Vdc controller output / Vdc_ctrl output
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Description:
Displays the actual output of the Vdc controller (DC link voltage controller)
Note:
The regenerative power limit p1531 is used for vector control to pre-control the Vdc_max controller. The lower the
power limit is set, the lower the correction signals of the controller when the voltage limit is reached.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-181
Parameters
List of Parameters
p1280[0...n]
Vdc controller or Vdc monitoring configuration (U/f) / Vdc_ctr config U/f
PM230
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
1
Description:
Sets the configuration of the controller for the DC link voltage (Vdc controller) in the U/f operating mode.
Value:
0:
1:
Note:
For high input voltages (see p0210), the following settings can improve the degree of ruggedness of the Vdc_max
controller:
Inhib Vdc ctrl
Vdc_max controller enable
- Set the input voltage p0210 as low as possible (in so doing avoid A07401).
- Set the rounding times (p1130, p1136).
- Increase the ramp-down times (p1121).
- Reduce the integral time of the controller (p1291) (factor 0.5).
- Activate the Vdc correction in the current controller (p1810 bit 1 = 1) or reduce the derivative action time of the
controller (p1292) (factor 0.5).
In this case, we always recommend using vector control (p1300 = 20) (Vdc controller, see p1240).
p1280[0...n]
Vdc controller or Vdc monitoring configuration (U/f) / Vdc_ctr config U/f
PM240
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
1
Description:
Sets the configuration of the controller for the DC link voltage (Vdc controller) in the U/f operating mode.
Value:
0:
1:
2:
3:
Note:
For high input voltages (see p0210), the following settings can improve the degree of ruggedness of the Vdc_max
controller:
Inhib Vdc ctrl
Vdc_max controller enable
Vdc_min controller (kinetic buffering) enable
Vdc_min controller and Vdc_max controller enable
- Set the input voltage p0210 as low as possible (in so doing avoid A07401).
- Set the rounding times (p1130, p1136).
- Increase the ramp-down times (p1121).
- Reduce the integral time of the controller (p1291) (factor 0.5).
- Activate the Vdc correction in the current controller (p1810 bit 1 = 1) or reduce the derivative action time of the
controller (p1292) (factor 0.5).
In this case, we generally recommend to use vector control (p1300 = 20) (Vdc controller, see p1240).
The following measures are suitable to improve the Vdc_min controller:
- Optimize the Vdc_min controller (see p1287).
- Activate the Vdc correction in the current controller (p1810 bit 1 = 1).
1-182
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1282
Vdc_max controller switch-in level (U/f) / Vdc_max on_level
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Description:
Factory setting
- [V]
Displays the switch-in level for the Vdc_max controller.
If p1294 = 0 (automatic sensing of the switch-in level = off), then the following applies:
r1282 = 1.15 * sqrt(2) * V_mains = 1.15 * sqrt(2) * p0210 (supply voltage)
If p1294 = 1 (automatic sensing of the switch-in level = on), then the following applies:
r1282 = Vdc_max - 50.0 V (Vdc_max: Overvoltage threshold of the power unit)
Note:
The Vdc_max controller is not switched back off until the DC-link voltage falls below the threshold 0.95 * p1282 and
the controller output is zero.
p1283[0...n]
Vdc_max controller dynamic factor (U/f) / Vdc_max dyn_factor
PM230
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1 [%]
Max
10000 [%]
Description:
Factory setting
100 [%]
Sets the dynamic factor for the DC link voltage controller (Vdc_max controller).
100% means that p1290, p1291, and p1292 (gain, integral time, and rate time) are used in accordance with their
basic settings and on the basis of a theoretical controller optimization.
If subsequent optimization is required, this can be carried out using the dynamic factor. In this case, p1290, p1291,
and p1292 are weighted with the dynamic factor p1283.
p1285[0...n]
Vdc_min controller switch-in level (kinetic buffering) (U/f) / Vdc_min on_level
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
65 [%]
Max
150 [%]
Description:
Factory setting
76 [%]
Sets the switch-in level for the Vdc-min controller (kinetic buffering).
The value is obtained as follows:
p1286[V] = p1285[%] * sqrt(2) * p0210
Warning:
An excessively high value may adversely affect normal drive operation.
r1286
Vdc_min controller switch-in level (kinetic buffering) (U/f) / Vdc_min on_level
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
Displays the switch-in level for the Vdc_min controller (kinetic buffering).
Note:
The Vdc_min controller is not switched back off until the DC-link voltage rises above the threshold 1.05 * p1286 and
the controller output is zero.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-183
Parameters
List of Parameters
p1287[0...n]
Vdc_min controller dynamic factor (kinetic buffering) (U/f) / Vdc_min dyn_factor
PM240
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1 [%]
Max
10000 [%]
Description:
Factory setting
100 [%]
Sets the dynamic factor for the Vdc_min controller (kinetic buffering).
100% means that p1290, p1291, and p1292 (gain, integral time, and rate time) are used corresponding to their
basic settings and based on a theoretical controller optimization.
If subsequent optimization is required, this can be carried out using the dynamic factor. In this case, p1290, p1291,
and p1292 are weighted with the dynamic factor p1287.
p1288[0...n]
Vdc_max controller feedback coupling factor ramp-fct. gen. (U/f) /
Vdc_max factor RFG
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
100.000
Factory setting
0.500
Description:
Sets the feedback factor for the ramp-function generator. Its ramp times are decelerated relative to the output signal
of the Vdc_max controller.
Note:
For values p1288 = 0.0 to 0.5, the controller dynamics are automatically adapted internally.
p1290[0...n]
Vdc controller proportional gain (U/f) / Vdc_ctrl Kp
PM230
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
1.00
Description:
Sets the proportional gain for the Vdc controller (DC link voltage controller).
Note:
The gain factor is proportional to the capacitance of the DC link. The parameter is pre-set to a value that is optimally
adapted to the capacitance of the power unit.
p1291[0...n]
Vdc controller integral time (U/f) / Vdc_ctrl Tn
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Description:
Factory setting
40 [ms]
Sets the integral time for the Vdc controller (DC link voltage controller).
p1292[0...n]
Vdc controller rate time (U/f) / Vdc_ctrl t_rate
PM230
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
PM240
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
1000 [ms]
Description:
1-184
Factory setting
10 [ms]
Sets the rate time constant for the Vdc controller (DC link voltage controller).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1293[0...n]
Vdc min controller output limit (U/f) / Vdc_min outp_lim
PM240
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
600.00 [Hz]
Factory setting
600.00 [Hz]
Description:
Sets the output limit for the Vdc min controller (DC link undervoltage controller).
p1294
Vdc_max controller automatic detection ON signal level (U/f) / Vdc_max SenseOnLev
PM230
Access level: 3
Calculated: -
Data type: Integer16
PM240
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Activates/de-activates the automatic sensing of the switch-in level for the Vdc_max controller. When the sensing
function is de-activated, the activation threshold r1282 for the Vdc_max controller is determined from the parameterized connection voltage p0210.
Value:
0:
1:
p1295[0...n]
Vdc_min controller time threshold (U/f) / Vdc_min t_thresh
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
10000.000 [s]
Description:
Automatic detection inhibited
Automatic detection enabled
Factory setting
0.000 [s]
Sets the time threshold for the Vdc_min controller (kinetic buffering). If this value is exceeded a fault is output; the
required response can be parameterized.
Prerequisite: p1296 = 1.
Notice:
If a time threshold has been parameterized, the Vdc_max controller should also be activated (p1280 = 3) so that the
drive does not shut down with overvoltage when Vdc_min control is exited (due to the time violation) and in the
event of fault response OFF3. It is also possible to increase the OFF3 ramp-down time p1135.
p1296[0...n]
Vdc_min controller response (kinetic buffering) (U/f / Vdc_min response
PM240
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Sets the response for the Vdc_min controller (kinetic buffering).
Value:
0:
1:
Note:
Re p1296 = 1:
Factory setting
0
Buffer Vdc until undervoltage, n<p1297 -> F07405
Buff. Vdc until undervolt., n<p1297 -> F07405, t>p1295 -> F07406
The quick stop ramp entered in p1135 must not be equal to zero, to prevent overcurrent shutdown if F07406 is triggered.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-185
Parameters
List of Parameters
p1297[0...n]
Vdc_min controller speed threshold (U/f) / Vdc_min n_thresh
PM240
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Description:
Factory setting
50.00 [rpm]
Sets the speed threshold for the Vdc-min controller (kinetic buffering).
If this value is exceeded a fault is output; the required response can be parameterized .
r1298
CO: Vdc controller output (U/f) / Vdc_ctrl output
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM240
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the actual output of the Vdc controller (DC link voltage controller)
p1300[0...n]
Open-loop/closed-loop control operating mode / Op/cl-lp ctrl_mode
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(1), T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
22
Description:
Sets the open and closed-loop control mode of a drive.
Value:
0:
1:
2:
3:
4:
5:
6:
7:
19:
20:
22:
Dependency:
Factory setting
0
U/f control with linear characteristic
U/f control with linear characteristic and FCC
U/f control with parabolic characteristic
U/f control with parameterizable characteristic
U/f control with linear characteristic and ECO
U/f control for drives requiring a precise freq. (e.g. textiles)
U/f control for drives requiring a precise frequency and FCC
U/f control for a parabolic characteristic and ECO
U/f control with independent voltage setpoint
Speed control (encoderless)
Torque control (encoderless)
Only operation with U/f characteristic is possible if the rated motor speed is not entered (p0311).
Operation with a U/f characteristic is not supported for 1LE4 synchronous motors.
Refer to: p0300, p0311, p0500, p1501
Notice:
Active slip compensation is required in the U/f control types with Eco mode (p1300 = 4, 7). The scaling of the slip
compensation (p1335) should be set so that the slip is completely compensated (generally 100%).
The Eco mode is only effective in steady-state operation and when the ramp-function generator is not bypassed. In
the case of analog setpoints, if required the tolerance for ramp-up and ramp-down should be actively increased for
the ramp-function generator using p1148 in order to reliably signal a steady-state condition.
Note:
Only by selecting closed-loop speed control (p1300 = 20) is it possible to change over in operation to closed-loop
torque control (p1501). At the changeover, the setting of p1300 does not change. In this case, the actual state is
displayed in r1407, bit 2 and bit 3.
For the open-loop control modes p1300 = 5 and 6 (textile sector), slip compensation p1335, resonance damping
p1338, and the Imax frequency controller are switched off internally so that the output frequency can be set precisely. The Imax voltage controller remains active.
During operation (the pulses enabled) the open-loop/closed-loop control mode cannot be changed by changing
over drive data sets.
1-186
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1310[0...n]
Description:
Voltage boost permanent / U_boost perm
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
250.0 [%]
Factory setting
50.0 [%]
Defines the voltage boost as a [%] referred to the rated motor current (p0305).
The magnitude of the permanent voltage boost is reduced with increasing frequency so that at the rated motor frequency, the rated motor voltage is present.
The magnitude of the boost in Volt at a frequency of zero is defined as follows:
Voltage boost [V] = 1.732 x p0305 (rated motor current [A]) x r0395 (stator/primary section resistance [ohm]) x
p1310 (permanent voltage boost [%]) / 100 %
At low output frequencies, there is only a low output voltage in order to maintain the motor flux. However, the output
voltage can be too low in order to achieve the following:
- magnetize the induction motor.
- hold the load.
- compensate for losses in the system.
This is the reason that the output voltage can be increased using p1310.
The voltage boost can be used for both linear as well as square-law U/f characteristics.
Dependency:
The current limit p0640 limits the boost.
For vector control, the permanent voltage boost (p1310) has no effect as the drive converter automatically sets the
optimum operating conditions.
Refer to: p1300, p1311, p1312, r1315
Notice:
The voltage boost increases the motor temperature (particularly at zero speed).
Note:
The voltage boost is only effective for U/f control (p1300).
The boost values are combined with one another if the permanent voltage boost (p1310) is used in conjunction with
other boost parameters (acceleration boost (p1311), voltage boost for starting (p1312)).
However, these parameters are assigned the following priorities: p1310 > p1311, p1312
p1311[0...n]
Description:
Voltage boost at acceleration / U_boost accelerate
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
250.0 [%]
Factory setting
0.0 [%]
p1311 only results in a voltage boost when accelerating and generates a supplementary torque to accelerate the
load.
The voltage boost becomes effective for a positive setpoint increase and disappears as soon as the setpoint has
been reached. The build-up and withdrawal of the voltage boost are smoothed.
The magnitude of the boost in Volt at a frequency of zero is defined as follows:
Voltage boost [V] = 1.732 * p0305 (rated motor current [A]) x r0395 (stator/primary section resistance [ohm]) x
p1311 (voltage boost when accelerating [%]) / 100 %
Dependency:
The current limit p0640 limits the boost.
Refer to: p1300, p1310, p1312, r1315
Notice:
The voltage boost results in a higher motor temperature increase.
Note:
The voltage boost when accelerating can improve the response to small, positive setpoint changes.
Assigning priorities for the voltage boosts: refer to p1310
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-187
Parameters
List of Parameters
p1312[0...n]
Description:
Voltage boost when starting / U_boost starting
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
250.0 [%]
Factory setting
0.0 [%]
Setting for an additional voltage boost when powering-up, however, only for the first acceleration phase.
The voltage boost becomes effective for a positive setpoint increase and disappears as soon as the setpoint has
been reached. The build-up and withdrawal of the voltage boost are smoothed.
Dependency:
The current limit p0640 limits the boost.
Refer to: p1300, p1310, p1311, r1315
Notice:
The voltage boost results in a higher motor temperature increase.
Note:
The voltage boost when accelerating can improve the response to small, positive setpoint changes.
Assigning priorities for the voltage boosts: refer to p1310
r1315
Description:
Voltage boost total / U_boost total
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Displays the total resulting voltage boost in volt.
r1315 = p1310 + p1311 + p1312
Dependency:
p1320[0...n]
Description:
Dependency:
Note:
1-188
Refer to: p1310, p1311, p1312
U/f control programmable characteristic frequency 1 / Uf char f1
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
3000.00 [Hz]
Factory setting
0.00 [Hz]
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
This parameter specifies the voltage of the first point along the characteristic.
Selects the freely programmable characteristic using p1300 = 3.
The following applies to the frequency values: p1320 <= p1322 <= p1324 <= p1326. Otherwise, a standard characteristic is used that contains the rated motor operating point.
Refer to: p1300, p1310, p1311, p1321, p1322, p1323, p1324, p1325, p1326, p1327
Linear interpolation is carried out between the points 0 Hz/p1310, p1320/p1321 ... p1326/p1327.
The voltage boost when accelerating (p1311) is also applied to the freely programmable U/f characteristic.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1321[0...n]
U/f control programmable characteristic voltage 1 / Uf char U1
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [Vrms]
Max
10000.0 [Vrms]
Factory setting
0.0 [Vrms]
Description:
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
Dependency:
Selects the freely programmable characteristic using p1300 = 3.
This parameter specifies the voltage of the first point along the characteristic.
Refer to: p1310, p1311, p1320, p1322, p1323, p1324, p1325, p1326, p1327
Note:
Linear interpolation is carried out between the points 0 Hz/p1310, p1320/p1321 ... p1326/p1327.
The voltage boost when accelerating (p1311) is also applied to the freely programmable U/f characteristic.
p1322[0...n]
U/f control programmable characteristic frequency 2 / Uf char f2
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
3000.00 [Hz]
Factory setting
0.00 [Hz]
Description:
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
Dependency:
The following applies to the frequency values: p1320 <= p1322 <= p1324 <= p1326. Otherwise, a standard characteristic is used that contains the rated motor operating point.
This parameter specifies the voltage of the second point along the characteristic.
Refer to: p1310, p1311, p1320, p1321, p1323, p1324, p1325, p1326, p1327
p1323[0...n]
Description:
U/f control programmable characteristic voltage 2 / Uf char U2
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [Vrms]
Max
10000.0 [Vrms]
Factory setting
0.0 [Vrms]
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
This parameter specifies the voltage of the second point along the characteristic.
Dependency:
p1324[0...n]
Refer to: p1310, p1311, p1320, p1321, p1322, p1324, p1325, p1326, p1327
U/f control programmable characteristic frequency 3 / Uf char f3
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
3000.00 [Hz]
Factory setting
0.00 [Hz]
Description:
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
Dependency:
The following applies to the frequency values: p1320 <= p1322 <= p1324 <= p1326. Otherwise, a standard characteristic is used that contains the rated motor operating point.
This parameter specifies the voltage of the third point along the characteristic.
Refer to: p1310, p1311, p1320, p1321, p1322, p1323, p1325, p1326, p1327
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-189
Parameters
List of Parameters
p1325[0...n]
U/f control programmable characteristic voltage 3 / Uf char U3
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [Vrms]
Max
10000.0 [Vrms]
Factory setting
0.0 [Vrms]
Description:
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
Dependency:
Refer to: p1310, p1311, p1320, p1321, p1322, p1323, p1324, p1326, p1327
This parameter specifies the voltage of the third point along the characteristic.
p1326[0...n]
Description:
U/f control programmable characteristic frequency 4 / Uf char f4
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
10000.00 [Hz]
Factory setting
0.00 [Hz]
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
This parameter specifies the frequency of the fourth point along the characteristic.
Dependency:
Selects the freely programmable characteristic using p1300 = 3.
The following applies for the frequency values:
p1320 <= p1322 <= p1324 <= p1326
Otherwise, a standard characteristic is used that contains the rated motor operating point.
Refer to: p1310, p1311, p1320, p1321, p1322, p1323, p1324, p1325, p1327
Note:
Linear interpolation is carried out between the points 0 Hz/p1310, p1320/p1321 ... p1326/p1327. For output frequencies above p1326, the characteristic is extrapolated with the gradient between the characteristic points
p1324/p1325 and p1326/p1327.
The voltage boost when accelerating (p1311) is also applied to the freely programmable U/f characteristic.
p1327[0...n]
U/f control programmable characteristic voltage 4 / Uf char U4
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [Vrms]
Max
10000.0 [Vrms]
Factory setting
0.0 [Vrms]
Description:
The programmable characteristic for the U/f control is defined using 4 points and 0 Hz/p1310.
Dependency:
Selects the freely programmable characteristic using p1300 = 3.
This parameter specifies the voltage of the fourth point along the characteristic.
Refer to: p1310, p1311, p1320, p1321, p1322, p1323, p1324, p1325, p1326
Note:
Linear interpolation is carried out between the points 0 Hz/p1310, p1320/p1321 ... p1326/p1327.
The voltage boost when accelerating (p1311) is also applied to the freely programmable U/f characteristic.
p1330[0...n]
CI: U/f control independent voltage setpoint / Uf U_set independ.
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2001
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the voltage setpoint for U/f control with an independent voltage setpoint (p1300 = 19).
Dependency:
Selects the U/f control with independent voltage setpoint via p1300 = 19.
Refer to: p1300
1-190
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1333[0...n]
U/f control FCC starting frequency / U/f FCC f_start
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
3000.00 [Hz]
Factory setting
0.00 [Hz]
Description:
Sets the starting frequency at which FCC (Flux Current Control) is activated.
Dependency:
The correct operating mode must be set (p1300 = 1, 6).
Warning:
An excessively low value can result in instability.
Note:
For p1333 = 0 Hz, the FCC starting frequency is automatically set to 6 % of the rated motor frequency.
p1334[0...n]
U/f control slip compensation starting frequency / Slip comp start
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
3000.00 [Hz]
Factory setting
0.00 [Hz]
Description:
Sets the starting frequency of the slip compensation.
Note:
For p1334 = 0, the starting frequency of the slip compensation is automatically set to 6 % of the rated motor frequency.
p1335[0...n]
Slip compensation, scaling / Slip comp scal
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
600.0 [%]
Factory setting
0.0 [%]
Sets the setpoint for slip compensation in [%] referred to r0330 (motor rated slip).
p1335 = 0.0 %: Slip compensation de-activated.
p1335 = 100.0 %: The slip is completely compensated.
Dependency:
Prerequisite for a precise slip compensation for p1335 = 100 % are the precise motor parameters (p0350 ... p0360).
If the parameters are not precisely known, a precise compensation can be achieved by varying p1335.
For U/f control types with Eco optimization (4 and 7), the slip compensation must be activated in order to guarantee
correct operation.
Note:
The purpose of slip compensation is to maintain a constant motor speed regardless of the applied load. The fact
that the motor speed decreases with increasing load is a typical characteristic of induction motors.
For synchronous motors, this effect does not occur and the parameter has no effect in this case.
For the open-loop control modes p1300 = 5 and 6 (textile sector), the slip compensation is internally disabled in
order to be able to precisely set the output frequency.
If p1335 is changed during commissioning (p0010 > 0), then it is possible that the old value will no longer be able to
be set. The reason for this is that the dynamic limits of p1335 have been changed by a parameter that was set when
the drive was commissioned (e.g. p0300).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-191
Parameters
List of Parameters
p1336[0...n]
Slip compensation limit value / Slip comp lim val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [%]
Max
600.00 [%]
Factory setting
250.00 [%]
Description:
Sets the limit value for slip compensation in [%] referred to r0330 (motor rated slip).
r1337
CO: Actual slip compensation / Slip comp act val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the actual compensated slip [%] referred to r0330 (rated motor slip).
Dependency:
p1335 > 0 %: Slip compensation active.
Refer to: p1335
p1338[0...n]
U/f mode resonance damping gain / Uf Res_damp gain
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
0.00
Description:
Sets the gain for resonance damping for U/f control.
Dependency:
Refer to: p1300, p1339, p1349
Note:
The resonance damping function dampens active current oscillations that frequency occur under no-load conditions.
The resonance damping is active in a range of approximately 5 ... 90 % of the rated motor frequency (p0310), but
up to a maximum of 45 Hz.
For the open-loop control modes p1300 = 5 and 6 (textile sectors), the resonance damping is internally disabled in
order that the output frequency can be precisely set.
p1339[0...n]
U/f mode resonance damping filter time constant / Uf Res_damp T
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1.00 [ms]
Max
1000.00 [ms]
Description:
Sets the filter time constant for resonance damping for U/f control.
Dependency:
Refer to: p1300, p1338, p1349
1-192
Factory setting
20.00 [ms]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1340[0...n]
Description:
Dependency:
Notice:
Note:
p1341[0...n]
I_max frequency controller proportional gain / I_max_ctrl Kp
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
0.500
Factory setting
0.000
Sets the proportional gain of the I_max voltage controller.
The I_max controller reduces the drive converter output current if the maximum current (r0067) is exceeded.
In the U/f operating modes (p1300) for the I_max control, one controller is used that acts on the output frequency
and one controller that acts on the output voltage. The frequency controller reduces the current by decreasing the
converter output frequency. The frequency is reduced down to a minimum value (equaling twice rated slip). If the
overcurrent condition cannot be successfully resolved using this measure, then the drive converter output voltage is
reduced using the I_max voltage controller. Once the overcurrent condition has been resolved, the drive is accelerated along the ramp set in p1120 (ramp-up time).
In the U/f modes (p1300) for textile applications and for external voltage setpoints, only the I_max voltage controller
is used.
When de-activating the I_max controller, the following must be carefully observed:
When the maximum current (r0067) is exceeded, the output current is no longer reduced, however, overcurrent
alarm messages are generated. The drive is shut down if the overcurrent limit (r0209) is exceeded.
The I_max limiting controller becomes ineffective if the ramp-function generator is de-activated with p1122 = 1.
p1341 = 0: I_max frequency controller de-activated and I_max voltage controller activated over the complete speed
range.
I_max frequency controller integral time / I_max_ctrl Tn
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
50.000 [s]
Factory setting
0.300 [s]
Description:
Sets the integral time for the I_max frequency controller.
Dependency:
Refer to: p1340
Note:
When p1341 = 0, the current limiting controller influencing the frequency is de-activated and only the current limiting
controller influencing the output voltage remains active (p1345, p1346).
In the case of power units with regenerative feedback (PM250, PM260), current limitation control for a regenerative
load is always implemented by influencing the frequency. This current limiting function is de-activated with p1340 =
p1341 = 0.
r1343
CO: I_max controller frequency output / I_max_ctrl f_outp
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the effective frequency limit.
Dependency:
Refer to: p1340
r1344
I_max controller voltage output / I_max_ctrl U_outp
Factory setting
- [rpm]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Description:
Displays the amount by which the converter output voltage is reduced.
Dependency:
Refer to: p1340
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [Vrms]
1-193
Parameters
List of Parameters
p1345[0...n]
I_max voltage controller proportional gain / I_max_U_ctrl Kp
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
100000.000
Factory setting
0.000
Description:
Sets the proportional gain for the I_max voltage controller.
Dependency:
Refer to: p1340
Note:
The controller settings are also used in the current controller of the DC braking (refer to p1232).
p1346[0...n]
I_max voltage controller integral time / I_max_U_ctrl Tn
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
50.000 [s]
Description:
Sets the integral time for the I_max voltage controller.
Dependency:
Refer to: p1340
Note:
p1346 = 0: Integral time of the I_max voltage controller de-activated.
Factory setting
0.030 [s]
The controller settings are also used in the current controller of the DC braking (refer to p1232).
r1348
Description:
Dependency:
Note:
p1349[0...n]
Description:
Dependency:
Note:
1-194
CO: U/f control Eco factor actual value / U/f Eco fac act v
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the economic factor determined for optimizing motor consumption.
Refer to: p1335
The value is only determined for operating modes with Economic (p1300 = 4, 7).
U/f mode resonance damping maximum frequency / Uf res_damp f_max
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [Hz]
Max
3000.00 [Hz]
Factory setting
0.00 [Hz]
Sets the maximum output frequency for resonance damping for U/f control.
Resonance damping is inactive above this output frequency.
Refer to: p1338, p1339
For p1349 = 0, the changeover limit is automatically set to 95 % of the rated motor frequency - however, to a max.
of 45 Hz.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1350[0...n]
Soft starting / Soft starting
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Sets whether the voltage is continuously increased during the magnetizing phase (p1350 = 1, On) or whether it
jumps directly to the voltage boost (p1350 = 0, Off).
Value:
0:
1:
Note:
The settings for this parameter have the following advantages and disadvantages:
OFF
ON
0 = off (jump directly to voltage boost)
Advantage: Flux is established quickly -> torque is quickly available
Disadvantage: The motor can move while it is being magnetized
1 = on (voltage is continually established)
Advantage: The motor is unlikely to rotate
Disadvantage: The flux is established slower -> torque is available later
p1351[0...n]
CO: Motor holding brake starting frequency / Brake f_start
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-300.00 [%]
Max
300.00 [%]
Factory setting
0.00 [%]
Description:
Sets the frequency setting value at the slip compensation output for starting up with motor holding brake.
Dependency:
When setting p1351 > 0, then slip compensation is automatically activated (p1335 = 100 %).
Refer to: p1352
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
Connected with p1352 a value of 100% corresponds to the motor rated slip (r0330).
p1352[0...n]
CI: Motor holding brake starting frequency signal source / Brake f_start
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1351[0]
Description:
Sets the signal source for the frequency setting value at the slip compensation output for starting up with motor
holding brake.
Dependency:
Refer to: p1216
Note:
A value of 100% corresponds to the motor rated slip (r0330).
The setting of the starting frequency begins after magnetizing (see p0346, r0056.4) and ends once the brake opening time (p1216) has elapsed and the starting frequency (p1334) has been reached.
A setting value of zero means that no setting procedure will take place.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-195
Parameters
List of Parameters
p1400[0...n]
Speed control configuration / n_ctrl config
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1000 0000 0010 0001 bin
Description:
Sets the configuration for the closed-loop speed control.
Bit field:
Bit
00
01
05
06
14
15
Note:
Re bit 01:
Signal name
Automatic Kp/Tn adaptation active
Sensorless vector control freeze I comp
Kp/Tn adaptation active
Free Tn adaptation active
Torque pre-control
Sensorless vector control, speed pre-control
1 signal
Yes
Yes
Yes
Yes
Always active
Yes
0 signal
No
No
No
No
For n_ctrl enab
No
FP
6040
6040
6040
6050
6060
6030
When the bit is set, the I component of the speed controller is kept when changing into the open-loop controlled
mode.
p1401[0...n]
Flux control configuration / Flux ctrl config
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0110 bin
Description:
Sets the configuration for flux setpoint control
Bit field:
Bit
00
01
02
Signal name
Flux setpoint soft starting active
Flux setpoint differentiation active
Flux build-up control active
1 signal
Yes
Yes
Yes
0 signal
No
No
No
06
07
Quick magnetizing
Pre-control speed limitation
Yes
Yes
No
No
Note:
FP
6722
6723
6722,
6723
6722
6640
Re bit 00 (not for permanent-magnet synchronous motors):
Initially, the flux is only established with a low rate of rise when magnetizing the induction motor. The flux setpoint
p1570 is reached again at the end of the magnetizing time p0346.
Re bit 01 (not for permanent-magnet synchronous motors):
Initially, the flux is only established with a low rate of rise when magnetizing the induction motor. The flux setpoint
p1570 is reached again at the end of the magnetizing time p0346. When quick magnetizing (p1401.6 = 1) is
selected, soft starting is internally de-activated and alarm A07416 is displayed.
The flux differentiation can be switched out if a significant ripple occurs in the field-generating current setpoint
(r0075) when entering the field weakening range. However, this is not suitable for fast acceleration operations
because then, the flux decays more slowly and the voltage limiting responds.
Re bit 02 (not for permanent-magnet synchronous motors):
The flux build-up control operates during the magnetizing phase p0346 of the induction motor. If it is switched out, a
constant current setpoint is injected and the flux is built up corresponding to the rotor time constant. When quick
magnetizing (p1401.6 = 1) is selected and when flux build-up control is de-energized alarm A07416 is displayed.
Re bit 06 (not for induction motors):
Magnetizing is performed with maximum current (0.9 * r0067). With active identification of the stator resistance (see
p0621) quick magnetizing is internally de-activated and alarm A07416 is displayed. During a flying restart of a rotating motor (see p1200) no quick magnetizing takes place.
Re bit 07:
if the speed of the drive exceeds the effective speed limit of the speed limiting controller, the torque limit is reduced
linearly to zero as the deviation becomes greater. This reduces the integral component of the speed controller and,
in turn, the overshoot during load shedding (see also F07901 and p2162).
1-196
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1402[0...n]
Closed-loop current control and motor model configuration / I_ctrl config
Access level: 4
Calculated: p0340 = 1,3
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 bin
Description:
Sets the configuration for the closed-loop control and the motor model.
Bit field:
Bit
02
r1406.4...15
CO/BO: Control word speed controller / STW n_ctrl
Signal name
Current controller adaptation active
1 signal
Yes
0 signal
No
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the control word of the speed controller.
Bit field:
Bit
04
05
11
12
15
r1407.0...15
CO/BO: Status word speed controller / ZSW n_ctrl
Signal name
Hold speed controller I component
Set speed controller I component
Droop enable
Torque control active
Set speed adaptation controller I component
FP
-
1 signal
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
FP
6040
6040
6030
6060
-
Factory setting
-
Description:
Displays the status word of the speed controller.
Bit field:
Bit
00
01
02
Signal name
U/f control active
Encoderless operation active
Torque control active
1 signal
Yes
Yes
Yes
0 signal
No
No
No
03
05
06
07
08
09
10
11
12
13
15
Speed control active
Speed controller I component frozen
Speed controller I component set
Torque limit reached
Upper torque limit active
Lower torque limit active
Droop enabled
Speed setpoint limited
Ramp-function generator set
Encoderless operation due to a fault
Torque limit reached (without pre-control)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
FP
6030,
6060,
8010
6040
6040
6040
6060
6060
6060
6030
6030
6060
1-197
Parameters
List of Parameters
r1408.0...14
CO/BO: Status word current controller / ZSW I_ctrl
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the current controller status word.
Bit field:
Bit
00
01
03
10
12
13
14
p1416[0...n]
Signal name
Current ctrl act
Id control, I component limiting
Voltage limiting
Speed adaptation, limiting
Motor stalled
Separately excited synchronous motor is
excited
Current model FEM: magnetizing excitation
current limited to 0
Factory setting
1 signal
Active
Active
Active
Active
Yes
Yes
0 signal
Not active
Not active
Not active
Not active
No
No
FP
6714
6714
-
Yes
No
-
Speed setpoint filter 1 time constant / n_set_filt 1 T
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
5000.00 [ms]
Description:
Sets the time constant for the speed setpoint filter 1 (PT1).
r1438
CO: Speed controller, speed setpoint / n_ctrl n_set
Factory setting
0.00 [ms]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the speed setpoint after setpoint limiting for the P component of the speed controller.
Dependency:
Refer to: r1439
Note:
In the standard state (the reference model is de-activated), r1438 = r1439.
r1439
Speed setpoint, I component / n_set I_comp
For U/f operation, the value that is displayed is of no relevance.
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the speed setpoint for the I component of the speed controller (output of the reference model after the setpoint limiting).
Dependency:
Refer to: r1438
Note:
In the standard state (the reference model is de-activated), r1438 = r1439.
1-198
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1444
Description:
Speed controller, speed setpoint steady-state (static) / n_ctrl n_set stat
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the sum of all speed setpoints that are present.
The following sources are available for the displayed setpoint:
- setpoint at the ramp-function generator input (r1119).
- speed setpoint 1 (p1155).
- speed setpoint 2 (p1160).
- speed setpoint for the speed pre-control (p1430).
- setpoint from DSC (for DSC active).
- setpoint via PC (for master control active).
Dependency:
Refer to: r1119, p1155, p1160
r1445
CO: Actual speed smoothed / n_act smooth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the actual smoothed actual speed for speed control.
p1452[0...n]
Speed controller speed actual value smoothing time (SLVC) / n_C n_act T_s SLVC
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
32000.00 [ms]
Factory setting
10.00 [ms]
Description:
Sets the smoothing time for the actual speed of the speed controller for encoderless closed-loop speed control.
Note:
The smoothing must be increased if there is gear backlash. For longer smoothing times, the integral time of the
speed controller must also be increased (e.g. using p0340 = 4).
r1454
CO: Speed controller system deviation I component / n_ctrl sys dev Tn
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the system deviation of the I component of the speed controller.
p1455[0...n]
CI: Speed controller P gain adaptation signal / n_ctrl Adpt_sig Kp
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the source for the adaptation signal to additionally adapt the P gain of the speed controller.
Dependency:
Refer to: p1456, p1457, p1458, p1459
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-199
Parameters
List of Parameters
p1456[0...n]
Description:
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [%]
Max
400.00 [%]
Factory setting
0.00 [%]
Sets the lower starting point of the adaptation range for the additional adaptation of the P gain of the speed controller.
The values are in % and refer to the set source of the adaptation signal.
Dependency:
Refer to: p1455, p1457, p1458, p1459
Note:
If the upper transition point p1457 of the speed controller adaptation is set to lower values than the lower transition
p1456, then the controller gain below p1457 is adapted with p1459 and above p1456, with p1458.
p1457[0...n]
Description:
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [%]
Max
400.00 [%]
Factory setting
0.00 [%]
Sets the upper starting point of the adaptation range for the additional adaptation of the P gain of the speed controller.
The values are in % and refer to the set source of the adaptation signal.
Dependency:
Refer to: p1455, p1456, p1458, p1459
Note:
If the upper transition point p1457 of the speed controller adaptation is set to lower values than the lower transition
p1456, then the controller gain below p1457 is adapted with p1459 and above p1456, with p1458.
p1458[0...n]
Adaptation factor, lower / Adapt_factor lower
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200000.0 [%]
Factory setting
100.0 [%]
Description:
Sets the adaptation factor before the adaptation range (0 % ... p1456) to additionally adapt the P gain of the
speed/velocity controller.
Dependency:
Refer to: p1455, p1456, p1457, p1459
Note:
If the upper transition point p1457 of the speed controller adaptation is set to lower values than the lower transition
p1456, then the controller gain below p1457 is adapted with p1459 and above p1456, with p1458.
p1459[0...n]
Adaptation factor, upper / Adapt_factor upper
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200000.0 [%]
Factory setting
100.0 [%]
Description:
Sets the adaptation factor after the adaptation range (> p1457) to additionally adapt the P gain of the speed/velocity
controller.
Dependency:
Refer to: p1455, p1456, p1457, p1458
Note:
If the upper transition point p1457 of the speed controller adaptation is set to lower values than the lower transition
p1456, then the controller gain below p1457 is adapted with p1459 and above p1456, with p1458.
1-200
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1461[0...n]
Speed controller Kp adaptation speed, upper scaling / n_ctrl Kp n upper
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200000.0 [%]
Factory setting
100.0 [%]
Description:
Sets the P gain of the speed controller for the upper adaptation speed range (> p1465). The entry is made referred
to the P gain for the lower adaptation speed range of the speed controller (% referred to p1470).
Dependency:
Refer to: p1464, p1465
Note:
If the upper transition point p1465 of the speed controller adaptation is set to lower values than the lower transition
p1464, then the controller gain below p1465 is adapted with p1461. This means that an adaptation can be implemented for low speeds without having to change the controller parameters.
p1463[0...n]
Speed controller Tn adaptation speed, upper scaling / n_ctrl Tn n upper
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200000.0 [%]
Factory setting
100.0 [%]
Description:
Sets the integral time of the speed controller after the adaptation speed range (> p1465). The entry is made referred
to the integral time for the lower adaptation speed range of the speed controller (% referred to p1472).
Dependency:
Refer to: p1464, p1465
Note:
If the upper transition point p1465 of the speed controller adaptation is set to lower values than the lower transition
point p1464, then the controller integral time below p1465 is adapted with p1463. This means that an adaptation
can be implemented for low speeds without having to change the controller parameters.
p1464[0...n]
Speed controller adaptation speed, lower / n_ctrl n lower
Description:
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
0.00 [rpm]
Sets the lower adaptation speed of the speed controller.
No adaptation is effective below this speed.
Dependency:
Refer to: p1461, p1463, p1465
Note:
If the upper transition point p1465 of the speed controller adaptation is set to lower values than the lower transition
point p1464, then the controller below p1465 is adapted with p1461 or p1463. This means that an adaptation can
be implemented for low speeds without having to change the controller parameters.
p1465[0...n]
Speed controller adaptation speed, upper / n_ctrl n upper
Description:
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
210000.00 [rpm]
Sets the upper adaptation speed of the speed controller.
No adaptation is effective above this speed.
For P gain, p1470 x p1461 is effective. For the integral time, p1472 x p1463 is effective.
Dependency:
Refer to: p1461, p1463, p1464
Note:
If the upper transition point p1465 of the speed controller adaptation is set to lower values than the lower transition
point p1464, then the controller below p1465 is adapted with p1461 or p1463. This means that an adaptation can
be implemented for low speeds without having to change the controller parameters.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-201
Parameters
List of Parameters
p1466[0...n]
CI: Speed controller P-gain scaling / n_ctrl Kp scal
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Description:
Sets the signal source for the scaling of the P gain of the speed controller. This also makes the effective P gain
(including adaptations) scalable.
r1468
CO: Speed controller P-gain effective / n_ctr Kp eff
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the effective P gain of the speed controller.
r1469
Speed controller integral time effective / n_ctr Tn eff
Description:
p1470[0...n]
Factory setting
-
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Factory setting
- [ms]
Displays the effective integral time of the speed controller.
Speed controller encoderless operation P-gain / n_ctrl SLVC Kp
Access level: 2
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
999999.000
Factory setting
0.300
Description:
Sets the P gain for encoderless operation for the speed controller.
Note:
The product p0341 x p0342 is taken into account when automatically calculating the speed controller (p0340 = 1, 3,
4).
p1472[0...n]
Speed controller encoderless operation integral time / n_ctrl SLVC Tn
Access level: 2
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
100000.0 [ms]
Factory setting
20.0 [ms]
Description:
Set the integral time for encoderless operation for the speed controller.
Note:
The integral component is stopped if the complete controller output or the sum of controller output and torque precontrol reach the torque limit.
1-202
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1475[0...n]
CI: Speed controller torque setting value for motor holding brake / n_ctrl M_sv MHB
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the torque setting value when starting up with motor holding brake.
Dependency:
The switching in of the torque setting value for the motor holding brake has a higher priority than the setting of the
integrator value using p1477 and p1478.
Note:
The setting of the integral output of the speed controller begins after magnetizing (see p0346, r0056 bit 4) and ends
at the end of the brake control opening time p1216. A setting value of zero means that no setting procedure will take
place.
If p1351 is used as a signal source for the torque setting value, the percentage value is interpreted in relation to the
rated torque (p2003).
p1476[0...n]
BI: Speed controller hold integrator / n_ctrl integ stop
Access level: 4
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to hold the integrator for the speed controller.
p1477[0...n]
BI: Speed controller set integrator value / n_ctrl integ set
Description:
Dependency:
Notice:
p1478[0...n]
Description:
Dependency:
Notice:
Factory setting
0
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source to set the integrator setting value (p1478).
Refer to: p1478, p1479
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
CI: Speed controller integrator setting value / n_ctr integ_setVal
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the integrator setting value for the velocity controller.
The signal to set this integrator setting value is interconnected via p1477.
The setting value of the speed controller integrator is weighted with the scaling factor of the signal source in p1479.
If p1478 is interconnected to the integral output of the speed controller (r1482), then after the magnetizing time
(r0346) and if the speed controller is enabled, the integral component of the controller is set to the last value before
the pulse inhibit. This value is set if no setting command (p1477) is interconnected or, at the instant that the pulses
were inhibited, a setting command is available, which is not de-activated up to the next time that the pulses are
inhibited. For sensorless vector control, in addition p1400.1 should be set to 1 so that when the drive is stopped, the
integral component of the speed controller is not controlled down to zero.
In order that when setting the integrator output, only the static torque is detected, we recommend that the accelerating torque is completely pre-controlled (e.g. p1496).
If p1478 is interconnected to another output other than r1482, then after magnetizing and speed controller enable,
the integral output is set once if the setting command is not interconnected (p1477 = 0).
Refer to: p1477, p1479
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-203
Parameters
List of Parameters
p1479[0...n]
CI: Speed controller integrator setting value scaling / n_ctrl I_val scal
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Description:
Sets the signal source for scaling the integrator setting value (p1478) of the speed controller.
Dependency:
Refer to: p1477, p1478
r1482
CO: Speed controller I torque output / n_ctrl I-M_output
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Description:
Displays the torque setpoint at the output of the I speed controller.
p1486[0...n]
CI: Droop compensation torque / Droop M_comp
Factory setting
- [Nm]
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the compensation torque to be output within the droop calculation.
p1487[0...n]
Droop compensation torque scaling / Droop M_comp scal
Description:
p1488[0...n]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-2000.0 [%]
Max
2000.0 [%]
Sets the scaling for the compensation torque within the droop calculation.
Droop input source / Droop input source
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
3
Description:
Sets the source for droop feedback.
Value:
0:
1:
2:
3:
Dependency:
Refer to: p1489, r1490, p1492
1-204
Factory setting
100.0 [%]
Factory setting
0
Droop feedback not connected
Droop from torque setpoint
Droop from speed controller output
Droop from integral output, speed controller
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1489[0...n]
Droop feedback scaling / Droop scaling
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
0.500
Description:
Sets the scaling for the droop feedback
Dependency:
Refer to: p1488, r1490, p1492
Note:
Example:
Factory setting
0.050
A value of 0.05 means that for a torque equal to the rated motor torque, the rated motor speed is reduced by 5 %.
r1490
CO: Droop feedback speed reduction / Droop n_reduction
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the output signal of the droop calculation. The droop feedback result is subtracted from the speed setpoint
when activated (p1492).
Dependency:
Refer to: p1488, p1489, p1492
p1492[0...n]
BI: Droop feedback enable / Droop enable
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Enables the droop to be applied to the speed/velocity setpoint.
Dependency:
Refer to: p1488, p1489, r1490
Note:
Even when not enabled, the droop speed is calculated but not subtracted from the setpoint speed. This makes it
possible to subtract the result of this calculation from the speed of another drive.
r1493
CO: Moment of inertia, total / M_inertia total
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: 25_1
Unit selection: p0100
Min
- [kgm²]
Max
- [kgm²]
Factory setting
- [kgm²]
Displays the parameterized total moment of inertia ((p0341 * p0342) * p1496).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-205
Parameters
List of Parameters
p1496[0...n]
Acceleration pre-control scaling / a_before scaling
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
10000.0 [%]
Factory setting
0.0 [%]
Description:
Sets the scaling for the acceleration pre-control of the speed/velocity controller.
Dependency:
Refer to: p0341, p0342
Note:
The parameter is set to 100% by the rotating measurement (refer to p1960).
The acceleration pre-control may not be used if the speed setpoint manifests significant ripple (e.g. analog setpoint)
and the rounding-off in the speed ramp-function generator is disabled.
We also recommend that the pre-control mode is not used if there is gearbox backlash.
p1499[0...n]
Accelerating for torque control, scaling / a for M_ctrl scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
400.0 [%]
Factory setting
100.0 [%]
Description:
Sets the scaling for the acceleration integrator at low speeds (only for encoderless torque control).
Dependency:
Refer to: p0341, p0342
p1500[0...n]
Torque setpoint selection / M_set sel
CU240B-2
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(1), T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
66
Description:
Factory setting
2
Sets the source for the torque setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
2:
6:
20:
22:
26:
60:
62:
66:
No main setpoint
Analog setpoint
Fieldbus
Analog setpoint + no main setpoint
Analog setpoint + analog setpoint
Analog setpoint + fieldbus
Fieldbus + no main setpoint
Fieldbus + analog setpoint
Fieldbus+fieldbus
Dependency:
When changing this parameter, the following settings are influenced:
Refer to: p1503, p1511
Caution:
1-206
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1500[0...n]
Torque setpoint selection / M_set sel
CU240B-2 DP
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(1), T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
66
Description:
Factory setting
6
Sets the source for the torque setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
2:
6:
20:
22:
26:
60:
62:
66:
No main setpoint
Analog setpoint
Fieldbus
Analog setpoint + no main setpoint
Analog setpoint + analog setpoint
Analog setpoint + fieldbus
Fieldbus + no main setpoint
Fieldbus + analog setpoint
Fieldbus+fieldbus
Dependency:
When changing this parameter, the following settings are influenced:
Refer to: p1503, p1511
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-207
Parameters
List of Parameters
p1500[0...n]
Torque setpoint selection / M_set sel
CU240E-2
Access level: 2
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(1), T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
77
Description:
Factory setting
2
Sets the source for the torque setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
2:
6:
7:
20:
22:
26:
27:
60:
62:
66:
67:
70:
72:
76:
77:
No main setpoint
Analog setpoint
Fieldbus
Analog setpoint 2
Analog setpoint + no main setpoint
Analog setpoint + analog setpoint
Analog setpoint + fieldbus
Analog setpoint + analog setpoint 2
Fieldbus + no main setpoint
Fieldbus + analog setpoint
Fieldbus+fieldbus
Fieldbus + analog setpoint 2
Analog setpoint 2 + no main setpoint
Analog setpoint 2 + analog setpoint
Analog setpoint 2 + fieldbus
Analog setpoint 2 + analog setpoint 2
Dependency:
When changing this parameter, the following settings are influenced:
Refer to: p1503, p1511
Caution:
1-208
When executing a specific macro, the corresponding programmed settings are made and become active.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1500[0...n]
Torque setpoint selection / M_set sel
CU240E-2 DP
Access level: 2
Calculated: -
Data type: Integer16
CU240E-2 DP F
Can be changed: C(1), T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
0
Max
77
Description:
Factory setting
6
Sets the source for the torque setpoint.
For single-digit values, the following applies:
The value specifies the main setpoint.
For double-digit values, the following applies:
The left-hand digit specifies the supplementary setpoint, the right-hand digit the main setpoint.
Example:
Value = 26
--> The analog setpoint (2) supplies the supplementary setpoint.
--> The fieldbus (6) supplies the main setpoint.
Value:
0:
2:
6:
7:
20:
22:
26:
27:
60:
62:
66:
67:
70:
72:
76:
77:
No main setpoint
Analog setpoint
Fieldbus
Analog setpoint 2
Analog setpoint + no main setpoint
Analog setpoint + analog setpoint
Analog setpoint + fieldbus
Analog setpoint + analog setpoint 2
Fieldbus + no main setpoint
Fieldbus + analog setpoint
Fieldbus+fieldbus
Fieldbus + analog setpoint 2
Analog setpoint 2 + no main setpoint
Analog setpoint 2 + analog setpoint
Analog setpoint 2 + fieldbus
Analog setpoint 2 + analog setpoint 2
Dependency:
When changing this parameter, the following settings are influenced:
Refer to: p1503, p1511
Caution:
When executing a specific macro, the corresponding programmed settings are made and become active.
p1501[0...n]
BI: Change over between closed-loop speed/torque control / Changeov n/M_ctrl
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for toggling between speed and torque control.
Dependency:
The input connectors to enter the torque are provided using p1511, p1512 and p1513.
Refer to: p1300
Caution:
If the closed-loop torque control is not activated (p1300) and a change is made to closed-loop torque control
(p1501), OFF1 (p0840) does not have its own braking response but pulse suppression when standstill is detected
(p1226, p1227).
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
0 signal: Closed-loop speed control
1 signal: Closed-loop torque control
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-209
Parameters
List of Parameters
p1503[0...n]
CI: Torque setpoint / M_set
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the torque setpoint for torque control.
Note:
A change is made to closed-loop torque control if, in p1300, closed-loop torque control was selected or if the selection was made using the changeover source in p1501.
it is also possible to change over in operation using p1501.
r1508
Description:
CO: Torque setpoint before supplementary torque / M_set bef. M_suppl
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Displays the torque setpoint before entering the supplementary torque.
For closed-loop speed control, r1508 corresponds to the speed controller output; for closed-loop torque control,
r1508 corresponds to the torque setpoint of the signal source assigned in p1503.
p1511[0...n]
CI: Supplementary torque 1 / M_suppl 1
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for supplementary torque 1.
p1512[0...n]
CI: Supplementary torque 1 scaling / M_suppl 1 scal
Description:
p1513[0...n]
Description:
1-210
Factory setting
0
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for scaling the supplementary torque 1.
CI: Supplementary torque 2 / M_suppl 2
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for supplementary torque 2.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1514[0...n]
Supplementary torque 2 scaling / M_suppl 2 scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-2000.0 [%]
Max
2000.0 [%]
Description:
Sets the scaling for supplementary torque 2.
r1515
Supplementary torque total / M_suppl total
Description:
Factory setting
100.0 [%]
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Displays the total supplementary torque.
The displayed value is the total of supplementary torque values 1 and 2 (p1511, p1512, p1513, p1514).
r1516
Description:
CO: Supplementary torque and acceleration torque / M_suppl + M_accel
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Displays the total supplementary torque and the accelerating torque.
The displayed value is the total of the smoothed supplementary torque and the accelerating torque (p1516 =
p1518[1] + r1515).
p1517[0...n]
Accelerating torque smoothing time constant / M_accel T_smooth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
100.00 [ms]
Factory setting
4.00 [ms]
Description:
Sets the smoothing time constant of the accelerating torque.
Note:
The acceleration pre-control is inhibited if the smoothing is set to the maximum value.
r1518[0...1]
CO: Accelerating torque / M_accel
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Description:
Displays the accelerating torque for pre-control of the speed controller.
Index:
[0] = Unsmoothed
[1] = Smoothed
Dependency:
Refer to: p0341, p0342, p1496
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [Nm]
1-211
Parameters
List of Parameters
p1520[0...n]
CO: Torque limit upper / M_max upper
Access level: 2
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2003
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
-1000000.00 [Nm]
Max
20000000.00 [Nm]
Factory setting
0.00 [Nm]
Description:
Sets the fixed, upper torque limit.
Dependency:
Refer to: p1521, p1522, p1523, r1538, r1539
Danger:
Negative values when setting the upper torque limit (p1520 < 0) can result in the motor accelerating in an uncontrollable fashion.
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
The torque limit is limited to 400% of the rated motor torque. When automatically calculating the motor/closed-loop
control parameters (p0340), the torque limit is set to match the current limit (p0640).
p1521[0...n]
CO: Torque limit lower / M_max lower
Access level: 2
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2003
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
-20000000.00 [Nm]
Max
1000000.00 [Nm]
Factory setting
0.00 [Nm]
Description:
Sets the fixed, lower torque limit.
Dependency:
Refer to: p1520, p1522, p1523
Danger:
Positive values when setting the lower torque limit (p1521 > 0) can result in the motor accelerating in an uncontrollable fashion.
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
The torque limit is limited to 400% of the rated motor torque. When automatically calculating the motor/closed-loop
control parameters (p0340), the torque limit is set to match the current limit (p0640).
p1522[0...n]
CI: Torque limit upper / M_max upper
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1520[0]
Description:
Sets the signal source for the upper torque limit.
Dependency:
Refer to: p1520, p1521, p1523
Danger:
Negative values resulting from the signal source and scaling can cause the motor to accelerate in an uncontrolled
manner.
1-212
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1523[0...n]
CI: Torque limit lower / M_max lower
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1521[0]
Description:
Sets the signal source for the lower torque limit.
Dependency:
Refer to: p1520, p1521, p1522
Danger:
Positive values resulting from the signal source and scaling can cause the motor to accelerate in an uncontrolled
manner.
p1524[0...n]
CO: Torque limit upper/motoring scaling / M_max up/mot scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-2000.0 [%]
Max
2000.0 [%]
Description:
Sets the scaling for the upper torque limit or the torque limit when motoring.
Dependency:
p1400.4 = 0: upper/lower
Factory setting
100.0 [%]
p1400.4 = 1: motoring / regenerating
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
This parameter can be freely interconnected.
The value has the meaning stated above if it is interconnected from connector input p1528.
p1525[0...n]
Description:
CO: Torque limit lower scaling / M_max lower scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-2000.0 [%]
Max
2000.0 [%]
Factory setting
100.0 [%]
Sets the scaling for the lower torque limit.
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
This parameter can be freely interconnected.
The value has the meaning stated above if it is interconnected from connector input p1528.
r1526
CO: Torque limit upper without offset / M_max up w/o offs
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Description:
Displays the upper torque limit of all torque limits without offset.
Dependency:
Refer to: p1520, p1521, p1522, p1523, p1528, p1529
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [Nm]
1-213
Parameters
List of Parameters
r1527
CO: Torque limit lower without offset / M_max low w/o offs
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Description:
Displays the lower torque limit of all torque limits without offset.
Dependency:
Refer to: p1520, p1521, p1522, p1523, p1528, p1529
p1528[0...n]
Factory setting
- [Nm]
CI: Torque limit upper scaling / M_max upper scal
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the scaling of the upper torque limit in p1522.
Danger:
For p1400.4 = 0 (torque limiting, upper/lower) the following applies:
Factory setting
1524[0]
Negative values resulting from the signal source and scaling can cause the motor to accelerate in an uncontrolled
manner.
Notice:
p1529[0...n]
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
CI: Torque limit lower scaling / M_max lower scal
Access level: 4
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the scaling of the lower torque limit in p1523.
Danger:
For p1400.4 = 0 (torque limiting, upper/lower) the following applies:
Factory setting
1525[0]
Positive values resulting from the signal source and scaling can cause the motor to accelerate in an uncontrolled
manner.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p1530[0...n]
Power limit motoring / P_max mot
Access level: 2
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 14_5
Unit selection: p0505
Min
0.00 [kW]
Max
100000.00 [kW]
Description:
Sets the power limit when motoring.
Dependency:
Refer to: p0500, p1531
Note:
The power limit is limited to 300% of the rated motor power.
1-214
Factory setting
0.00 [kW]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1531[0...n]
Power limit regenerative / P_max gen
Access level: 2
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 14_5
Unit selection: p0505
Min
-100000.00 [kW]
Max
-0.01 [kW]
Description:
Sets the regenerative power limit.
Dependency:
Refer to: r0206, p0500, p1530
Note:
The power limit is limited to 300% of the rated motor power.
Factory setting
-0.01 [kW]
For power units without regenerative feedback into the line supply, the regenerative power limit is pre-set to 30% of
the motoring power limit p1530 and in the ratio rated drive converter power to rated motor power.
For power units with energy recovery, the parameter is limited to the negative value of r0206[2].
r1533
Current limit torque-generating total / Iq_max total
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Description:
Displays the maximum torque/force generating current as a result if all current limits.
r1536
Current limit maximum torque-generating current / Isq_max
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Description:
Displays the maximum limit for the torque-generating current component.
r1537
Current limit minimum torque-generating current / Isq_min
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the minimum limit for the torque-generating current component.
r1538
CO: Upper effective torque limit / M_max upper eff
Factory setting
- [Arms]
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Description:
Displays the currently effective upper torque limit.
Note:
The effective upper torque limit is reduced with respect to the selected upper torque limit p1520, if the current limit
p0640 is reduced or the rated magnetizing current of the induction motor p0320 is increased.
This may be the case for rotating measurements (see p1960).
The torque limit p1520 can be re-calculated using p0340 = 1, 3 or 5.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-215
Parameters
List of Parameters
r1539
CO: Lower effective torque limit / M_max lower eff
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Description:
Displays the currently effective lower torque limit.
Note:
The effective lower torque limit is reduced with respect to the selected lower torque limit p1521, if the current limit
p0640 is reduced or the rated magnetizing current of the induction motor p0320 is increased.
This may be the case for rotating measurements (see p1960).
The torque limit p1520 can be re-calculated using p0340 = 1, 3 or 5.
r1547[0...1]
CO: Torque limit for speed controller output / M_max outp n_ctrl
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2003
Data set: -
Units group: 7_1
Unit selection: p0505
Min
- [Nm]
Max
- [Nm]
Factory setting
- [Nm]
Description:
Displays the torque limit to limit the speed controller output.
Index:
[0] = Upper limit
[1] = Lower limit
r1548[0...1]
CO: Stall current limit torque-generating maximum / Isq_max stall
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Description:
Displays the limit for the torque-generating current component using the stall calculation, the current limit of the
power unit as well as the parameterization in p0640.
Index:
[0] = Upper limit
[1] = Lower limit
p1552[0...n]
CI: Torque limit upper scaling without offset / M_max up w/o offs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Description:
Sets the signal source for the scaling of the upper torque limiting to limit the speed controller output without taking
into account the current and power limits.
p1554[0...n]
CI: Torque limit lower scaling without offset / M_max low w/o offs
Description:
1-216
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the signal source for the scaling of the lower torque limiting to limit the speed controller output without taking
into account the current and power limits.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1570[0...n]
Description:
CO: Flux setpoint / Flux setpoint
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
50.0 [%]
Max
200.0 [%]
Factory setting
100.0 [%]
Sets the flux setpoint referred to rated motor flux.
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
For p1570 > 100%, the flux setpoint increases as a function of the load from 100% (no-load operation) to the setting
in p1570 (above rated motor torque), if p1580 > 0% has been set.
p1571[0...n]
CI: Supplementary flux setpoint / Suppl flux setp
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2003
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the supplementary flux setpoint.
Notice:
Low flux setpoints can cause the drive to stall at higher loads. This is the reason that the flux setpoint should only be
adapted for slow load changes.
Note:
The supplementary flux setpoint is limited to +/- 50 %.
p1573[0...n]
Flux threshold value magnetizing / Flux thresh magnet
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10.0 [%]
Max
200.0 [%]
Factory setting
100.0 [%]
Description:
Sets the flux threshold value for enabling the speed setpoint and the end of magnetizing (r0056.4).
Note:
The parameter only has an influence if the flux actual value reaches the threshold value p1573 more quickly during
magnetizing than the time set in p0346.
The parameter has no influence for flying restart (see p1200) and after DC braking (see p1231).
p1574[0...n]
Voltage reserve dynamic / U_reserve dyn
PM230
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 5_1
Unit selection: p0505
Min
0.0 [Vrms]
Max
150.0 [Vrms]
Factory setting
2.0 [Vrms]
Description:
Sets a dynamic voltage reserve.
Dependency:
Refer to: p0500
Note:
In the field weakening range, it must be expected that the control dynamic performance is somewhat restricted due
to the limited possibilities of controlling/adjusting the voltage. This can be improved by increasing the voltage
reserve. Increasing the reserve reduces the steady-state maximum output voltage (r0071).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-217
Parameters
List of Parameters
p1574[0...n]
Voltage reserve dynamic / U_reserve dyn
PM240
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 5_1
Unit selection: p0505
Min
0.0 [Vrms]
Max
150.0 [Vrms]
Factory setting
10.0 [Vrms]
Description:
Sets a dynamic voltage reserve.
Dependency:
Refer to: p0500
Note:
In the field weakening range, it must be expected that the control dynamic performance is somewhat restricted due
to the limited possibilities of controlling/adjusting the voltage. This can be improved by increasing the voltage
reserve. Increasing the reserve reduces the steady-state maximum output voltage (r0071).
p1580[0...n]
Efficiency optimization / Efficiency opt.
PM230
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [%]
Max
100 [%]
Description:
Factory setting
80 [%]
Sets the efficiency optimization. When optimizing the efficiency, the flux setpoint of the closed-loop control is
adapted as a function of the load.
For p1580 = 100 %, under no-load operating conditions, the flux setpoint is reduced to 50 % of the rated motor flux.
Note:
It only makes sense to activate this function if the dynamic response requirements of the speed controller are low.
In order to avoid oscillations, if required, the speed controller parameters should be adapted (increase Tn, reduce
Kp).
Further, the smoothing time of the flux setpoint filter (p1582) should be increased.
p1580[0...n]
Efficiency optimization / Efficiency opt.
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [%]
Max
100 [%]
Factory setting
0 [%]
Description:
Sets the efficiency optimization. When optimizing the efficiency, the flux setpoint of the closed-loop control is
adapted as a function of the load.
Note:
It only makes sense to activate this function if the dynamic response requirements of the speed controller are low.
In order to avoid oscillations, if required, the speed controller parameters should be adapted (increase Tn, reduce
Kp).
For p1580 = 100 %, under no-load operating conditions, the flux setpoint is reduced to 50 % of the rated motor flux.
Further, the smoothing time of the flux setpoint filter (p1582) should be increased.
p1582[0...n]
Description:
1-218
Flux setpoint smoothing time / Flux setp T_smth
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
4 [ms]
Max
5000 [ms]
Factory setting
15 [ms]
Sets the smoothing time for the flux setpoint.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1583
Description:
Flux setpoint smoothed / Flux setp smooth
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the smoothed flux setpoint.
The value is referred to the rated motor flux.
p1584[0...n]
Field weakening operation, flux setpoint smoothing time / Field weak T_smth
Access level: 4
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
20000 [ms]
Factory setting
0 [ms]
Description:
Sets the smoothing time for the flux setpoint in the field-weakening range
Note:
Only the flux setpoint rise is smoothed
r1589
Field-weakening current, pre-control value / I_FieldWeak prectr
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Description:
Displays the pre-control value for the field weakening current.
r1593[0...1]
CO: Field weakening controller / flux controller output / Field/Fl_ctrl outp
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the output of the field weakening controller (synchronous motor).
Index:
[0] = PI output
[1] = I output
p1594[0...n]
Field-weakening controller, P gain / Field_ctrl Kp
Description:
Factory setting
- [Arms]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
1000.00
Factory setting
0.00
Sets the P gain of the field-weakening controller.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-219
Parameters
List of Parameters
p1596[0...n]
Field weakening controller integral-action time / Field_ctrl Tn
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [ms]
Max
10000 [ms]
Description:
Sets the integral-action time of the field-weakening controller.
r1597
CO: Field weakening controller output / Field_ctrl outp
Description:
Factory setting
300 [ms]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the output of the field weakening controller.
The value is referred to the rated motor flux.
r1598
Description:
CO: Total flux setpoint / Flux setp total
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the effective flux setpoint.
The value is referred to the rated motor flux.
p1610[0...n]
Description:
Torque setpoint static (SLVC) / M_set static
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-200.0 [%]
Max
200.0 [%]
Factory setting
50.0 [%]
Sets the static torque setpoint for sensorless vector control (SLVC).
This parameter is entered as a percentage referred to the rated motor torque (r0333).
For sensorless vector control, when the motor model is shut down, an absolute current is impressed. p1610 represents the maximum load that occurs at a constant setpoint speed.
Notice:
p1610 should always be set to at least 10 % higher than the maximum steady-state load that can occur.
Note:
For p1610 = 0%, a current setpoint is calculated that corresponds to the no-load case (ASM: rated magnetizing current).
For p1610 = 100 %, a current setpoint is calculated that corresponds to the rated motor torque.
Negative values are converted into positive setpoints in the case of induction and permanent-magnet synchronous
motors.
1-220
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1611[0...n]
Supplementary accelerating torque (SLVC) / M_suppl_accel
Access level: 2
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200.0 [%]
Factory setting
30.0 [%]
Description:
Enters the dynamic torque setpoint for the low-speed range for sensorless vector control (SLVC). This parameter is
entered as a percentage referred to the rated motor torque (r0333).
Note:
When accelerating and braking p1611 is added to p1610 and the resulting total torque is converted into an appropriate current setpoint and controlled.
For pure accelerating torques, it is always favorable to use the torque pre-control of the speed controller (p1496).
p1616[0...n]
Description:
Current setpoint smoothing time / I_set T_smooth
Access level: 4
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
4 [ms]
Max
10000 [ms]
Factory setting
40 [ms]
Sets the smoothing time for the current setpoint.
The current setpoint is generated from p1610 and p1611.
Note:
This parameter is only effective in the range where current is injected for sensorless vector control.
r1623[0...1]
Field-generating current setpoint (steady-state) / Id_set stationary
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Description:
Displays the steady-state field generating current setpoint (Id_set).
Note:
Re index 1:
Factory setting
- [Arms]
Displays the stationary field-generating current on the stator side in the case of separately excited synchronous
motors without the excitation current monitoring component (r1644).
r1624
Description:
Field-generating current setpoint, total / Id_setp total
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Displays the limited field-generating current setpoint (Id_set).
This value comprises the steady-state field-generating current setpoint r1623 and a dynamic component that is only
set when changes are made to the flux setpoint.
r1650
Description:
Current setpoint torque-generating before filter / Iq_set before filt
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2002
Data set: -
Units group: 6_2
Unit selection: p0505
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Displays the torque generating current setpoint Iqset after the torque limits and the clock cycle interpolation is
ahead of the current setpoint filters.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-221
Parameters
List of Parameters
p1654[0...n]
Curr. setpoint torque-gen. smoothing time field weakening range / Isq_s T_smth FW
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.1 [ms]
Max
50.0 [ms]
Factory setting
4.8 [ms]
Description:
Sets the smoothing time constant for the setpoint of the torque-generating current components.
Note:
The smoothing time does not become effective until the field-weakening range is reached.
p1702[0...n]
Isd current controller pre-control scaling / Isd_ctr_prectrScal
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200.0 [%]
Factory setting
70.0 [%]
Description:
Sets the scaling of the dynamic current controller pre-control for the flux-generating current component Isd.
Note:
The parameter is effective for permanent-magnet synchronous motors.
p1703[0...n]
Isq current controller pre-control scaling / Isq_ctr_prectrScal
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200.0 [%]
Factory setting
60.0 [%]
Description:
Sets the scaling of the dynamic current controller pre-control for the torque/force-generating current component Isq.
p1715[0...n]
Current controller P gain / I_ctrl Kp
Description:
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
100000.000
Factory setting
0.000
Sets the proportional gain of the current controller.
This value is automatically pre-set using p3900 or p0340 when commissioning has been completed.
p1717[0...n]
Current controller integral-action time / I_ctrl Tn
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
1000.00 [ms]
Description:
Sets the integral-action time of the current controller.
Dependency:
Refer to: p1715
1-222
Factory setting
2.00 [ms]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1718
Description:
CO: Isq controller output / Isq_ctrl outp
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Displays the actual output of the Isq current controller (torque/force generating current, PI controller).
The value contains the proportional and integral components of the PI controller.
r1719
Isq controller integral component / Isq_ctrl I_comp
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Displays the integral component of the Isq current controller (torque/force-generating current, PI controller).
r1723
CO: Isd controller output / Isd_ctrl outp
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Displays the actual output of the Isd current controller (flux-generating current, PI controller).
The value contains the proportional and integral components of the PI controller.
r1724
Isd controller integral component / Isd_ctrl I_comp
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Displays the integral component of the Isd current controller (flux-generating current, PI controller).
r1725
Isd controller integral component limit / Isd_ctrl I_limit
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Displays the limit value for the integral component of the Isd current controller.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-223
Parameters
List of Parameters
p1726[0...n]
Quadrature arm decoupling, scaling / Transv_decpl scal
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200.0 [%]
Factory setting
75.0 [%]
Description:
Sets the scaling of the quadrature arm decoupling
Note:
This parameter is ineffective for sensorless vector control. In this case, p1727 is always used. If p1726 is set to 0,
then the quadrature de-coupling is de-activated. The integral component of the Isd current controller remains effective in the complete speed control range.
For the closed-loop control of synchronous motors, this parameter is used to scale the current controller de-coupling.
p1727[0...n]
Quadrature arm decoupling at voltage limit scaling / TrnsvDecplVmaxScal
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
200.0 [%]
Factory setting
50.0 [%]
Description:
Sets the scaling of quadrature arm decoupling when the voltage limit is reached.
r1728
De-coupling voltage, in-line axis / U_dir-axis_decoupl
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Displays the actual output of the quadrature channel de-coupling for the d axis.
r1729
De-coupling voltage, quadrature axis / U_quad_decoupl
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Displays the actual output of the quadrature channel de-coupling for the q axis.
p1730[0...n]
Isd controller integral component shutdown threshold / Isd_ctrl I_thresh
Description:
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
30 [%]
Max
150 [%]
Factory setting
30 [%]
Sets the speed activation threshold (referred to the synchronous speed r0336 / r0313) for pure quadrature branch
operation of the closed-loop current control.
The d current controller is only effective as P controller for speeds greater than the threshold value.
Warning:
For settings above 80%, the d current controller is active up to the field weakening limit (maximum voltage)
This can result in unstable behavior as the closed-loop control at the maximum voltage is based on pure quadrature
branch operation.
Setting values as high as this should not be selected; they are only intended for test purposes.
Note:
1-224
The parameter is only effective for induction motor operation without an encoder.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1732[0...1]
CO: Direct-axis voltage setpoint / Direct U set
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Description:
Displays the direct-axis voltage setpoint Ud.
Index:
[0] = Unsmoothed
[1] = Smoothed with p0045
r1733[0...1]
Factory setting
- [Vrms]
CO: Quadrature-axis voltage setpoint / Quad U set
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_1
Unit selection: p0505
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Displays the quadrature-axis component of voltage setpoint Uq.
Index:
[0] = Unsmoothed
[1] = Smoothed with p0045
p1740[0...n]
Gain resonance damping for encoderless closed-loop control / Gain res_damp
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
10.000
Factory setting
0.025
Description:
Defines the gain of the controller for resonance damping for operation with sensorless vector control in the range
that current is injected.
p1745[0...n]
Motor model error threshold stall detection / MotMod ThreshStall
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
1000.0 [%]
Factory setting
5.0 [%]
Description:
Sets the fault threshold in order to detect a motor that has stalled.
Dependency:
If a stalled drive is detected (r1408.12 = 1), fault F07902 is output after the delay time set in p2178.
If the error signal (r1746) exceeds the parameterized error threshold, then status signal r1408.12 is set to 1.
Refer to: p2178
Note:
Monitoring is only effective in the low-speed range (below p1755 * (100% - p1756)).
r1746
Motor model error signal stall detection / MotMod sig stall
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Signal to initiate stall detection
Note:
The signal is not calculated while magnetizing and only in the low speed range (below p1755 * (100 % - p1756)).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-225
Parameters
List of Parameters
p1750[0...n]
Motor model configuration / MotMod config
PM230
Access level: 3
Calculated: p0340 = 1,3,5
Data type: Unsigned8
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
0000 1100 bin
Sets the configuration for the motor model.
Bit 0 = 1: Forces open-loop speed-controlled starting (ASM).
Bit 1 = 1: Forces the system to pass through frequency zero, open-loop-controlled (ASM).
Bit 2 = 1: Drive remains in full closed-loop control mode, even at zero frequency (ASM).
Bit 3 = 1: Motor model evaluates the saturation characteristic (ASM).
Bit 6 = 1: If the motor is blocked, sensorless vector control remains speed-controlled (ASM).
Bit field:
Bit
00
01
02
03
06
Signal name
Controlled start
Controlled through 0 Hz
Closed-loop ctrl oper. down to zero freq. for
passive loads
Motor model Lh_pre = f(PsiEst)
Closed-loop control when motor is blocked
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
-
Yes
Yes
No
No
-
Dependency:
Refer to: p0500
Caution:
Do not use bit 6 = 1 if the motor can be reversed by the load. Long delay times due to blocking (p2177) can cause
the motor to stall. In this case you should de-activate the function or use closed-loop control throughout the speed
range (note the information re bit 2 = 1).
Note:
Bits 0 ... 2 only have an influence for encoderless vector control, bit 2 is pre-assigned depending on p0500.
Re bit 2 = 1:
The sensorless vector control is effective down to zero frequency. A change is not made into the open-loop speed
controlled mode.
This operating mode is possible for passive loads. These include applications where the load itself does not generate any active torque and therefore only acts reactively to the drive torque of the induction motor.
If bit 2 = 1, then bit 3 is automatically set to 1. Manual de-selection is possible and may be sensible if the saturation
characteristic (p1960) was not measured for third-party motors. Generally, for standard SIEMENS motors, the
already pre-assigned (default value) saturation characteristic is adequate.
When the bit is set, the selection of bits 0 and 1 is ignored.
Re bit 2 = 0:
Bit 3 is also automatically deactivated.
Re bit 6 = 1:
The following applies for encoderless vector control of induction motors:
For a blocked motor (see p2175, p2177) the time condition in p1758 is bypassed and a change is not made into
open-loop controlled operation.
1-226
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1750[0...n]
Motor model configuration / MotMod config
PM240
Access level: 3
Calculated: p0340 = 1,3,5
Data type: Unsigned8
PM250, PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
0000 0000 bin
Sets the configuration for the motor model.
Bit 0 = 1: Forces open-loop speed-controlled starting (ASM).
Bit 1 = 1: Forces the system to pass through frequency zero, open-loop-controlled (ASM).
Bit 2 = 1: Drive remains in full closed-loop control mode, even at zero frequency (ASM).
Bit 3 = 1: Motor model evaluates the saturation characteristic (ASM).
Bit 6 = 1: If the motor is blocked, sensorless vector control remains speed-controlled (ASM).
Bit field:
Bit
00
01
02
03
06
Signal name
Controlled start
Controlled through 0 Hz
Closed-loop ctrl oper. down to zero freq. for
passive loads
Motor model Lh_pre = f(PsiEst)
Closed-loop control when motor is blocked
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
-
Yes
Yes
No
No
-
Dependency:
Refer to: p0500
Caution:
Do not use bit 6 = 1 if the motor can be reversed by the load. Long delay times due to blocking (p2177) can cause
the motor to stall. In this case you should de-activate the function or use closed-loop control throughout the speed
range (note the information re bit 2 = 1).
Note:
Bits 0 ... 2 only have an influence for encoderless vector control, bit 2 is pre-assigned depending on p0500.
Re bit 2 = 1:
The sensorless vector control is effective down to zero frequency. A change is not made into the open-loop speed
controlled mode.
This operating mode is possible for passive loads. These include applications where the load itself does not generate any active torque and therefore only acts reactively to the drive torque of the induction motor.
If bit 2 = 1, then bit 3 is automatically set to 1. Manual de-selection is possible and may be sensible if the saturation
characteristic (p1960) was not measured for third-party motors. Generally, for standard SIEMENS motors, the
already pre-assigned (default value) saturation characteristic is adequate.
When the bit is set, the selection of bits 0 and 1 is ignored.
Re bit 2 = 0:
Bit 3 is also automatically deactivated.
Re bit 6 = 1:
The following applies for encoderless vector control of induction motors:
For a blocked motor (see p2175, p2177) the time condition in p1758 is bypassed and a change is not made into
open-loop controlled operation.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-227
Parameters
List of Parameters
r1751
Motor model status / MotMod status
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status of the motor model.
Bit field:
Bit
00
01
02
03
05
06
07
08
09
10
11
12
13
14
15
16
17
p1755[0...n]
Signal name
Controlled operation
Set ramp-function generator
Stop RsLh adaptation
Feedback
Holding angle
Acceleration criterion
Set angular integrator PEM
Stop Kt adaptation PEM
PolID active PEM SLVC
I injection PEM
Speed controller output cannot be set to
zero
Rs adapt waits
Motor operation
Stator frequency sign
Torque sign
Pulse injection active PEM
Operation with feedback
Factory setting
1 signal
Active
Active
Yes
Active
Yes
Active
No
No
No
No
Yes
0 signal
Inactive
Inactive
No
Inactive
No
Inactive
Yes
Yes
Yes
Yes
No
FP
6721
-
Yes
Yes
Positive
Motor mode
Yes
Selected
No
No
Negative
Regenerative mode
No
Deselected
-
Motor model changeover speed encoderless operation / MotMod n_chgSnsorl
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
210000.00 [rpm]
Description:
Sets the speed to change over the motor model to encoderless operation.
Dependency:
Refer to: p1756
Notice:
The changeover speed represents the steady-state minimum speed up to which the motor model can be used
in steady-state operation without encoder.
If the stability is not adequate close to the changeover speed, it may make sense to increase the parameter value.
Note:
The changeover speed applies for the changeover between open-loop and closed-loop control mode.
p1756
Motor model changeover speed hysteresis encoderless operation /
MotMod n_chgov hys
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [%]
Max
95.0 [%]
Factory setting
50.0 [%]
Description:
Sets the hysteresis for the changeover speed of the motor model for encoderless operation.
Dependency:
Refer to: p1755
Note:
The parameter value refers to p1755.
1-228
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1758[0...n]
Motor model changeover delay time closed/open-loop control / MotMod t cl_op
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
100 [ms]
Max
10000 [ms]
Factory setting
500 [ms]
Description:
Sets the minimum time for falling below the changeover speed when changing from closed-loop controlled operation to open-loop controlled operation.
Dependency:
Refer to: p1755, p1756
p1759[0...n]
Motor model changeover delay time open/closed-loop control / MotMod t op_cl
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
2000 [ms]
Factory setting
0 [ms]
Description:
Sets the minimum time for exceeding the changeover speed when changing from open-loop controlled operation to
closed-loop controlled operation.
Dependency:
Refer to: p1755, p1756
Note:
When p1759 = 2000 ms, the delay time becomes ineffective and the model changeover is determined by the output
frequency only.
r1762[0...1]
Description:
Motor model deviation component 1 / MotMod dev comp 1
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Induction motor (ASM):
Displays the referred imaginary system deviation for the adaptation circuit of the motor model.
Permanent-magnet synchronous motor (PESM):
Displays the system deviation for speed adaptation.
r1762.0: Angular deviation [rad-el] of the estimated EMF.
r1762.1: Angular deviation [electr. deg.] of the low-level signal response for pulse technique.
Index:
[0] = Deviation Model1
[1] = Deviation Model2
r1763
Motor model deviation component 2 / MotMod dev comp 2
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Induction motor (ASM):
Displays the referred real system deviation for the adaptation circuit of the motor model.
Permanent-magnet synchronous motor (PESM):
Not used.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-229
Parameters
List of Parameters
p1764[0...n]
Motor model without encoder speed adaptation Kp / MotMod woE n_adaKp
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
100000.000
Factory setting
1000.000
Description:
Sets the proportional gain of the controller for speed adaptation without encoder.
r1765
Motor model, speed adaptation Kp effective / MotM n_ada Kp act
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the effective proportional gain of the controller for the speed adaptation.
p1767[0...n]
Motor model without encoder speed adaptation Tn / MotMod woE n_adaTn
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1 [ms]
Max
200 [ms]
Factory setting
4 [ms]
Description:
Sets the integral time of the controller for speed adaptation without encoder
r1768
Motor model, speed adaptation Vi effective / MotM n_ada Vi act
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the effective gain of the integral component of the controller for speed adaptation.
r1770
CO: Motor model speed adaptation proportional component / MotMod n_adapt Kp
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the P component of the controller for speed adaptation.
r1771
CO: Motor model speed adaptation I comp. / MotMod n_adapt Tn
Description:
1-230
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays the I component of the controller for speed adaptation.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1773[0...1]
Description:
Index:
p1774[0...n]
Motor model slip speed / MotMod slip
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Displays estimated (speed) signals of the motor model.
r1773[0]: Displays the estimated (mechanical) slip of the motor model.
r1773[1]: Displays the estimated input speed of the motor model.
[0] = Slip speed estimated
[1] = Speed estimated
Motor model, offset voltage compensation alpha / MotMod offs comp A
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-5.000 [V]
Max
5.000 [V]
Factory setting
0.000 [V]
Description:
Sets the offset voltage in the alpha direction; this compensates the offset voltages of the drive converter/inverter at
low speeds. The value is valid for the rated (nominal) pulse frequency of the power unit.
Note:
The value is pre-set during the rotating measurement.
p1775[0...n]
Motor model, offset voltage compensation beta / MotMod offs comp B
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-5.000 [V]
Max
5.000 [V]
Factory setting
0.000 [V]
Description:
Sets the offset voltage in the beta direction; this compensates the offset voltages of the drive converter/inverter at
low speeds. The value is valid for the rated (nominal) pulse frequency of the power unit.
Note:
The value is pre-set during the rotating measurement.
r1776[0...6]
Motor model status signals / MotMod status sig
Description:
Index:
Note:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the internal status signals of the motor model:
Index 0: Changeover ramp between current and voltage models
Index 1: Changeover ramp for model tracking (encoderless induction motors only)
Index 2: Changeover ramp for zero frequency range (encoderless induction motors only)
Index 3: Transition ramp actual speed from speed setpoint to model value (encoderless FEM)
Index 4: Speed controller enable (encoderless FEM)
Index 5: Transition ramp between current and voltage models (encoderless FEM)
Index 6: Transition ramp for EMF deviation at PLL input (encoderless PESM)
[0] = Changeover ramp motor model
[1] = Changeover ramp model tracking
[2] = Changeover ramp zero frequency encoderless ASM
[3] = Changeover ramp actual speed encoderless FEM
[4] = Enable speed controller encoderless FEM
[5] = Changeover ramp motor model encoderless FEM
[6] = Changeover ramp motor model encoderless PESM
Indices 3 through 5 are only relevant in the case of encoderless control of separately excited synchronous motors.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-231
Parameters
List of Parameters
r1778
Motor model flux angle difference / MotMod ang. diff.
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2005
Data set: -
Units group: -
Unit selection: -
Min
- [°]
Max
- [°]
Factory setting
- [°]
Description:
Dependency:
Displays the difference between the motor model flux angle and the transformation angle.
A setting for smoothing the display can be made using p1754.
p1780[0...n]
Motor model adaptation configuration / MotMod adapt conf
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0101 1100 bin
Description:
Sets the configuration for the adaptation circuit of the motor model.
Induction motor (ASM): Rs, Lh, and offset compensation.
Permanent magnet synchronous motor (PEM): kT
Bit field:
Bit
01
02
03
04
06
07
Signal name
Select motor model ASM Rs adaptation
Select motor model ASM Lh adaptation
Select motor model PEM kT adaptation
Select motor model offset adaptation
Select pole position identification PEM
encoderless
Select T(valve) with Rs adaptation
1 signal
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
FP
-
Yes
No
-
Note:
ASM: Induction motor
PEM: Permanent magnet synchronous motor
When selecting the compensation of the valve interlocking via Rs (bit 7), the compensation in the gating unit is deactivated and is instead taken into account in the motor model.
In order that the correction values of the Rs, Lh and kT adaptation (selected using Bit 0 ... Bit 2) are correctly
accepted when changing over the drive data set, a dedicated motor number must be entered into p0826 for each
different motor.
p1784[0...n]
Motor model feedback scaling / Mod_FB_scal
Access level: 3
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [%]
Max
1000.0 [%]
Factory setting
0.0 [%]
Description:
Sets the scaling for model fault feedback.
Note:
Feeding back the measured model fault to the model states increases the control stability and makes the motor
model rugged against parameter errors.
The model feedback is only effective for encoderless operation of the ASM.
When feedback is selected (p1784 > 0), Lh adaptation is not effective.
p1785[0...n]
Description:
1-232
Motor model Lh adaptation Kp / MotMod Lh Kp
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000
Max
10.000
Factory setting
0.100
Sets the proportional gain for the Lh adaptation of the motor model for an induction motor (ASM).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1786[0...n]
Description:
r1787[0...n]
Motor model Lh adaptation integral time / MotMod Lh Tn
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [ms]
Max
10000 [ms]
Factory setting
100 [ms]
Sets the integral time for the Lh adaptation of the motor model for an induction motor (ASM).
Motor model Lh adaptation corrective value / MotMod Lh corr
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the corrective value for the Lh adaptation of the motor model for an induction motor (ASM).
Dependency:
Refer to: p0826, p1780
Note:
The adaptation result is reset if the magnetizing inductance of the induction motor is changed (p0360, r0382). This
also happens when changing over the data set if a different motor is not being used (p0826).
The display of the inactive data sets is only updated when changing over the data set.
r1791
Motor model Lh adaptation power-on frequency / MotMod Lh f_on
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Hz]
Max
- [Hz]
Factory setting
- [Hz]
Description:
Displays the power-on stator frequency/ primary section frequency for the Lh adaptation for the induction motor
(ASM).
r1792
Motor model Lh adaptation power-on slip / MotMod Lh fslip
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Hz]
Max
- [Hz]
Factory setting
- [Hz]
Description:
Displays the power-on slip frequency for the Lh adaptation for the induction motor (ASM).
p1795[0...n]
Motor model kT adaptation integral time / MotMod kT Tn
Description:
Access level: 4
Calculated: p0340 = 1,3,4
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
10 [ms]
Max
10000 [ms]
Factory setting
100 [ms]
Sets the integral time of the kT adaptation of the motor model for a permanent-magnet synchronous motor (PEM).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-233
Parameters
List of Parameters
r1797[0...n]
Motor model kT adaptation corrective value / MotMod kT corr
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
- [Nm/A]
Max
- [Nm/A]
Factory setting
- [Nm/A]
Description:
Displays the corrective value of the kT adaptation of the motor model for a permanent-magnet synchronous motor
(PEM).
Dependency:
Refer to: p0826, p1780
Note:
The display of the inactive data sets is only updated when changing over the data set.
p1800[0...n]
Pulse frequency setpoint / Pulse freq setp
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
2.000 [kHz]
Max
16.000 [kHz]
Factory setting
4.000 [kHz]
Description:
Sets the pulse frequency for the converter.
Dependency:
Refer to: p0230
Note:
The maximum possible pulse frequency is also determined by the power unit being used.
This parameter is pre-set to the rated converter value when the drive is first commissioned.
When the pulse frequency is increased, depending on the particular power unit, the maximum output current can be
reduced (derating, refer to r0067).
If a sine-wave filter is parameterized as output filter (p0230 = 3), then the pulse frequency cannot be set below the
minimum value required for the filter.
For operation with output reactors, the pulse frequency is limited to 4 kHz (see p0230).
If p1800 is changed during commissioning (p0010 > 0), then it is possible that the old value will no longer be able to
be set. The reason for this is that the dynamic limits of p1800 have been changed by a parameter that was set when
the drive was commissioned (e.g. p1082).
r1801[0...1]
CO: Pulse frequency / Pulse frequency
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: -
Unit selection: -
Min
- [kHz]
Max
- [kHz]
Factory setting
- [kHz]
Description:
Display and connector output for the actual converter switching frequency.
Index:
[0] = Actual
[1] = Modulator minimum value
Note:
The selected pulse frequency (p1800) may be reduced if the drive converter has an overload condition (p0290).
1-234
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1802[0...n]
Modulator mode / Modulator mode
PM230
Access level: 3
Calculated: p0340 = 1,3,5
Data type: Integer16
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
10
Factory setting
10
Description:
Sets the modulator mode.
Value:
0:
2:
3:
4:
10:
Dependency:
If a sine-wave filter is parameterized as output filter (p0230 = 3, 4), then only space vector modulation without overcontrol can be selected as modulation type (p1802 = 3). This is not valid for the power units PM260. p1802 = 10 can
only be set for the PM230 and PM240 power units.
Automatic changeover SVM/FLB
Space vector modulation (SVM)
SVM without overcontrol
SVM/FLB without overcontrol
SVM/FLB with modulation depth reduction
Refer to: p0230, p0500
Note:
When modulation modes are enabled that could lead to overmodulation (p1802 = 0, 2, 10), the modulation depth
must be limited using p1803 (pre-assignment, p1803 = 98%). The higher the overmodulation, the greater the current ripple and torque ripple. With p1802 = 10, the modulation depth limit is automatically reduced to 100% in the
critical output frequency range (over approx. 57 Hz).
When changing p1802[x], the values for all of the other existing indices are also changed.
p1802[0...n]
Modulator mode / Modulator mode
PM240
Access level: 3
Calculated: p0340 = 1,3,5
Data type: Integer16
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
10
Factory setting
0
Description:
Sets the modulator mode.
Value:
0:
2:
3:
4:
10:
Dependency:
If a sine-wave filter is parameterized as output filter (p0230 = 3, 4), then only space vector modulation without overcontrol can be selected as modulation type (p1802 = 3). This is not valid for the power units PM260. p1802 = 10 can
only be set for the PM230 and PM240 power units.
Automatic changeover SVM/FLB
Space vector modulation (SVM)
SVM without overcontrol
SVM/FLB without overcontrol
SVM/FLB with modulation depth reduction
Refer to: p0230, p0500
Note:
When modulation modes are enabled that could lead to overmodulation (p1802 = 0, 2,10), the modulation depth
must be limited using p1803 (default p1803 < 100 %). The higher the overmodulation, the greater the current ripple
and torque ripple.
When changing p1802[x], the values for all of the other existing indices are also changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-235
Parameters
List of Parameters
p1802[0...n]
Modulator mode / Modulator mode
PM250
Access level: 3
Calculated: p0340 = 1,3,5
Data type: Integer16
PM260
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
4
Factory setting
4
Description:
Sets the modulator mode.
Value:
0:
2:
3:
4:
Dependency:
If a sine-wave filter is parameterized as output filter (p0230 = 3, 4), then only space vector modulation without overcontrol can be selected as modulation type (p1802 = 3). This is not valid for the power units PM260. p1802 = 10 can
only be set for the PM230 and PM240 power units.
Automatic changeover SVM/FLB
Space vector modulation (SVM)
SVM without overcontrol
SVM/FLB without overcontrol
Refer to: p0230, p0500
Note:
When modulation modes are enabled that could lead to overmodulation (p1802 = 0, 2,10), the modulation depth
must be limited using p1803 (default p1803 < 100 %). The higher the overmodulation, the greater the current ripple
and torque ripple.
When changing p1802[x], the values for all of the other existing indices are also changed.
p1803[0...n]
Maximum modulation depth / Modulat depth max
PM230
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
20.0 [%]
Max
120.0 [%]
Factory setting
115.0 [%]
Description:
Defines the maximum modulation depth.
Dependency:
Refer to: p0500
Note:
p1803 = 100% is the overcontrol limit for space vector modulation (for an ideal drive converter without any switching
delay).
p1803[0...n]
Maximum modulation depth / Modulat depth max
PM240
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
20.0 [%]
Max
150.0 [%]
Description:
Dependency:
Note:
Factory setting
106.0 [%]
Defines the maximum modulation depth.
Refer to: p0500
p1803 = 100% is the overcontrol limit for space vector modulation (for an ideal drive converter without any switching
delay).
p1803[0...n]
Maximum modulation depth / Modulat depth max
PM250
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
PM260
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
20.0 [%]
Max
150.0 [%]
Description:
Dependency:
Note:
1-236
Factory setting
106.0 [%]
Defines the maximum modulation depth.
Default setting PM260: 103 %.
Refer to: p0500
p1803 = 100% is the overcontrol limit for space vector modulation (for an ideal drive converter without any switching
delay).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1806[0...n]
Filter time constant Vdc correction / T_filt Vdc_corr
Access level: 4
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
10000.0 [ms]
Factory setting
0.0 [ms]
Description:
Sets the filter time constant of the DC link voltage used to calculate the modulation depth.
r1808
DC link voltage actual value for U_max calculation / Vdc act val U_max
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2001
Data set: -
Units group: 5_2
Unit selection: p0505
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
DC link voltage used to determine the maximum possible output voltage.
r1809
CO: Modulator mode actual / Modulator mode act
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2
Factory setting
-
Description:
Displays the effective modulator mode.
Value:
1:
2:
p1810
Modulator configuration / Modulator config
Flat top modulation (FLB)
Space vector modulation (SVM)
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the configuration for the modulator.
Bit field:
Bit
00
01
Signal name
Avg value filter for U_lim (only for
Vdc_comp. in modulator)
DC link voltage compensation in the current
control
Factory setting
0000 bin
1 signal
Yes
0 signal
No
FP
-
Yes
No
-
Notice:
Bit 1 = 1 can only be set under a pulse inhibit and for r0192.14 = 1.
Note:
Re bit 00 = 0:
Voltage limitation from the minimum of the DC link voltage (lower ripple in the output current, reduced output voltage).
Re bit 00 = 1:
Voltage limitation from averaged DC link voltage (higher output voltage with increased ripple in the output current).
The selection is only valid if the DC link compensation is not performed in the Control Unit (bit 1 = 0).
Re bit 01 = 0:
DC link voltage compensation in the modulator.
Re bit 01 = 1:
DC link voltage compensation in the current control.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-237
Parameters
List of Parameters
p1820[0...n]
Description:
Reverse the output phase sequence / Outp_ph_seq rev
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(2), T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Sets the phase sequence reversal for the motor without setpoint change.
If the motor does not rotate in the required direction, then the output phase sequence can be reversed using this
parameter. This means that the direction of the motor is reversed without the setpoint being changed.
Value:
0:
1:
OFF
ON
Note:
This setting can only be changed when the pulses are inhibited.
p1825
Converter valve threshold voltage / Threshold voltage
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [Vrms]
Max
100.0 [Vrms]
Factory setting
0.6 [Vrms]
Description:
Sets the threshold voltage drop of the valves (power semiconductor devices) to be compensated.
Note:
The value is automatically calculated in the motor data identification routine.
p1828
Compensation valve lockout time phase U / Comp t_lock ph U
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
3.99 [µs]
Factory setting
0.00 [µs]
Description:
Sets the valve lockout time to compensate for phase U.
Note:
The value is automatically calculated in the motor data identification routine.
p1829
Compensation valve lockout time phase V / Comp t_lock ph V
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
3.99 [µs]
Factory setting
0.00 [µs]
Description:
Sets the valve lockout time to compensate for phase V.
p1830
Compensation valve lockout time phase W / Comp t_lock ph W
Description:
1-238
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
3.99 [µs]
Factory setting
0.00 [µs]
Sets the valve lockout time to compensate for phase W.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1832
Description:
Dead time compensation current level / t_dead_comp I_lev
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0 [Arms]
Max
10000.0 [Arms]
Factory setting
0.0 [Arms]
Dependency:
Sets the current level for the dead time compensation.
Above the current level, the dead time - resulting from the converter switching delays - is compensated by a previously calculated constant value. If the relevant phase current setpoint falls below the absolute value defined by
p1832, the corrective value for this phase is continuously reduced.
The factor setting of p1832 is automatically set to 0.02 * rated drive converter current (r0207).
p1900
Motor data identification and rotating measurement / MotID and rot meas
Description:
Value:
Dependency:
Notice:
Note:
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: C(1), T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Sets the motor data identification and speed controller optimization.
p1900 = 0:
Function inhibited.
p1900 = 1:
Sets p1910 = 1 and p1960 = 0, 1 depending on p1300
When the drive enable signals are present, a motor data identification routine is carried out at standstill with the
next power-on command. Current flows through the motor which means that it can align itself by up to a quarter of
a revolution.
With the following power-on command, a rotating motor data identification routine is carried out - and in addition, a
speed controller optimization by making measurements at different motor speeds.
p1900 = 2:
Sets p1910 = 1 and p1960 = 0
When the drive enable signals are present, a motor data identification routine is carried out at standstill with the
next power-on command. Current flows through the motor which means that it can align itself by up to a quarter of
a revolution.
p1900 = 3:
Sets p1960 = 0, 1 depending on p1300
This setting should only be selected if the motor data identification was already carried out at standstill.
When the drive enable signals are present, with the next power-on command, a rotating motor data identification
routine is carried out - and in addition, speed controller optimization by taking measurements at different motor
speeds.
0:
Inhibited
1:
Identify motor data at standstill and with motor rotating
2:
Identify motor data at standstill
3:
Identify motor data with motor rotating
Refer to: p1300, p1910, p1960
Refer to: A07980, A07981, F07983, F07984, F07985, F07986, F07988, F07990, A07991
If there is a motor holding brake, it must be open (p1215 = 2).
To permanently accept the determined settings they must be saved in a non-volatile fashion (p0971).
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
The motor and control parameters are only optimally set when both measurements are carried out (initially at standstill, and then with the motor rotating).
An appropriate alarm is output when the parameter is set.
The power-on command must remain set during a measurement and after the measurement has been completed,
the drive automatically resets it.
The duration of the measurements can lie between 0.3 s and several minutes. This time is, for example, influenced
by the motor size and the mechanical conditions.
p1900 is automatically set to 0 after the motor data identification routine has been completed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-239
Parameters
List of Parameters
p1901
Description:
Test pulse evaluation configuration / Test puls config
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 bin
Sets the configuration for the test pulse evaluation.
Re bit 00:
Check for conductor-to-conductor short circuit when pulse is enabled.
Bit field:
Bit
00
Signal name
Phase short-circuit test pulse active
Note:
Re bit 00:
1 signal
Yes
0 signal
No
FP
-
If the test was successful once after POWER ON (see r1902.0), it is not repeated.
If a conductor-to-conductor short-circuit is detected during the test, this is displayed in r1902.1.
r1902
Description:
Test pulse evaluation status / Test puls ev stat
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the status of the test pulse evaluation.
Short-circuit test:
Bit 0: The short-circuit test was run without any faults detected.
Bit 1: A phase short circuit has been detected.
Bit field:
1-240
Bit
00
01
Signal name
Short-circuit test executed
Phase short-circuit detected
1 signal
Yes
Yes
0 signal
No
No
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1909[0...n]
Motor data identification control word / MotID STW
Access level: 3
Calculated: p0340 = 1
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0000 0000 0000 bin
Description:
Sets the configuration for the motor data identification.
Bit field:
Bit
00
02
03
05
06
07
11
12
14
15
Note:
Signal name
Stator inductance estimate no measurement
Rotor time constant estimate no measurement
Leakage inductance estimate no measurement
Determine Tr and Lsig evaluation in the time
range
Activate vibration damping
De-activate vibration detection
De-activate pulse measurement Lq Ld
De-activate rotor resistance Rr measurement
De-activate valve interlocking time measurement
Determine only stator resistance, valve voltage fault, dead time
1 signal
Yes
0 signal
No
FP
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
Yes
Yes
Yes
No
No
No
No
-
Yes
No
-
Yes
No
-
The following applies to permanent-magnet synchronous motors:
Without de-selection in bit 11, in the closed-loop control mode, the direct inductance LD and the quadrature inductance Lq are measured at a low current.
When de-selecting with bit 11 or in the U/f mode, the stator inductance is measured at half the rated motor current.
If the stator is inductance is not measured but is to be estimated, then bit 0 should be set and bit 11 should be deselected.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-241
Parameters
List of Parameters
p1910
Description:
Motor data identification selection / MotID selection
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
26
Factory setting
0
Sets the motor data identification routine.
The motor data identification routine is carried out after the next power-on command.
p1910 = 1:
All motor data and the drive converter characteristics are identified and then transferred to the following parameters:
p0350, p0354, p0356, p0357, p0358, p0360, p1825, p1828, p1829, p1830
After this, the control parameter p0340 = 3 is automatically calculated.
p1910 = 20:
Only for internal SIEMENS use.
Value:
0:
1:
2:
20:
21:
22:
23:
24:
25:
26:
Inhibited
Complete identification (ID) and acceptance of motor data
Complete identification (ID) of motor data without acceptance
Voltage vector input
Voltage vector input without filter
Rectangular voltage vector input without filter
Triangular voltage vector input without filter
Rectangular voltage vector input with filter
Triangular voltage vector input with filter
Enter voltage vector with DTC correction
Dependency:
"Quick commissioning" must be carried out (p0010 = 1, p3900 > 0) before executing the motor data identification
routine!
When selecting the motor data identification routine, the drive data set changeover is suppressed.
Refer to: p1900
Caution:
After the motor data identification (p1910 > 0) has been selected, alarm A07991 is output and a motor data identification routine is carried out as follows at the next power-on command:
- current flows through the motor and a voltage is present at the drive converter output terminals.
- during the identification routine, the motor shaft can rotate through a maximum of half a revolution.
- however, no torque torque is generated.
Notice:
If there is a motor holding brake, it must be open (p1215 = 2).
Note:
When setting p1910, the following should be observed:
1. "With acceptance" means:
The parameters specified in the description are overwritten with the identified values and therefore have an influence on the controller setting.
2. "Without acceptance" means:
The identified parameters are only displayed in the range r1912 ... r1926 (service parameters). The controller settings remain unchanged.
p1911
Number of phases to be identified / Qty ph to ident
To permanently accept the determined settings they must be saved in a non-volatile fashion (p0971).
Description:
Value:
Note:
1-242
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
3
Factory setting
1
Sets the number of phases to be identified.
1:
1 phase U
2:
2 phases U, V
3:
3 phases U, V, W
When identifying with several phases, the accuracy increases and also the time it takes to make the measurement.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1912[0...2]
Identified stator resistance / R_stator ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Description:
Displays the identified stator resistance.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1913[0...2]
Identified rotor time constant / T_rotor ident
Factory setting
- [ohm]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Description:
Displays the identified rotor time constant.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1914[0...2]
Identified total leakage inductance / L_total_leak ident
Factory setting
- [ms]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Description:
Displays the identified total leakage inductance.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1915[0...2]
Identified nominal stator inductance / L_stator ident
Factory setting
- [mH]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Description:
Displays the nominal stator inductance identified.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [mH]
1-243
Parameters
List of Parameters
r1916[0...2]
Identified stator inductance 1 / L_stator 1 ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the nominal stator inductance identified for the 1st point of the saturation characteristic.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1917[0...2]
Identified stator inductance 2 / L_stator 2 ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the nominal stator inductance identified for the 2nd point of the saturation characteristic.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1918[0...2]
Identified stator inductance 3 / L_stator 3 ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the nominal stator inductance identified for the 3rd point of the saturation characteristic.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1919[0...2]
Identified stator inductance 4 / L_stator 4 ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [mH]
Max
- [mH]
Factory setting
- [mH]
Description:
Displays the nominal stator inductance identified for the 4th point of the saturation characteristic.
Index:
[0] = Phase U
[1] = Phase V
[2] = Phase W
1-244
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1925[0...2]
Identified threshold voltage / U_threshold ident
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Vrms]
Max
- [Vrms]
Factory setting
- [Vrms]
Description:
Index:
Displays the identified IGBT threshold voltage.
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1926[0...2]
Identified effective valve lockout time / t_lock_valve id
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [µs]
Max
- [µs]
Factory setting
- [µs]
Description:
Index:
Displays the identified effective valve lockout time.
[0] = Phase U
[1] = Phase V
[2] = Phase W
r1927[0...2]
Identified rotor resistance / R_rotor ident
Description:
Index:
p1959[0...n]
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ohm]
Max
- [ohm]
Factory setting
- [ohm]
Displays identified rotor resistance (on separately excited synchronous motors: damping resistance).
[0] = Phase U
[1] = Phase V
[2] = Phase W
Rotating measurement configuration / Rot meas config
Access level: 3
Calculated: p0340 = 1
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0001 1110 bin
Description:
Sets the configuration of the rotating measurement.
Bit field:
Bit
01
02
03
04
Signal name
Saturation characteristic identification
Moment of inertia identification
Re-calculates the speed controller parameters
Speed controller optimization (vibration test)
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
-
Yes
No
-
Dependency:
Refer to: F07988
Note:
The following parameters are influenced for the individual optimization steps:
Bit 01: p0320, p0360, p0362 ... p0369
Bit 02: p0341, p0342
Bit 03: p1400.0, p1458, p1459, p1463, p1470, p1472, p1496
Bit 04: Dependent on p1960
p1960 = 1, 3: p1400.0, p1458, p1459, p1470, p1472, p1496
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-245
Parameters
List of Parameters
p1960
Description:
Rotating measurement selection / Rot meas sel
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Sets the rotating measurement.
The rotating measurement is carried out after the next power-on command.
The setting possibilities of the parameter depend on the open-loop/closed-loop control mode (p1300).
p1300 < 20 (U/f open-loop control):
It is not possible to select rotating measurement or speed controller optimization.
p1300 = 20, 22 (encoderless operation):
Only rotating measurement or speed controller optimization can be selected in the encoderless mode.
Value:
0:
1:
3:
Inhibited
Rotating measurement in encoderless operation
Speed controller optimization in encoderless operation
Dependency:
Before the rotating measurement is carried out, the motor data identification routine (p1900, p1910, r3925) should
have already been done.
When selecting the rotating measurement, the drive data set changeover is suppressed.
Refer to: p1300, p1900, p1959
Danger:
For drives with a mechanical system that limits the distance moved, it must be ensured that this is not reached during the rotating measurement. If this is not the case, then it is not permissible that the measurement is carried out.
Notice:
If there is a motor holding brake, it must be open (p1215 = 2).
Note:
When the rotating measurement is activated, it is not possible to save the parameters (p0971).
To permanently accept the determined settings they must be saved in a non-volatile fashion (p0971).
Parameter changes are automatically made for the rotating measurement (e.g. p1120); this is the reason that up to
the end of the measurement, and if no faults are present, no manual changes should be made.
The ramp-up and ramp-down times (p1120, p1121) are limited, for the rotating measurement, to 900 s.
p1961
Description:
Saturation characteristic speed to determine / Sat_char n determ
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
26 [%]
Max
75 [%]
Factory setting
40 [%]
Sets the speed to determine the saturation characteristic.
The percentage value is referred to p0310 (rated motor frequency).
Dependency:
Refer to: p0310, p1959
Refer to: F07983
Note:
1-246
The saturation characteristics should be determined at an operating point with the lowest possible load.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p1965
Description:
Speed_ctrl_opt speed / n_opt speed
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10 [%]
Max
75 [%]
Factory setting
40 [%]
Sets the speed for the identification of the moment of inertia and the vibration test.
Induction motor:
The percentage value is referred to p0310 (rated motor frequency).
Synchronous motor:
The percentage value is referred to the minimum from p0310 (rated motor frequency) and p1082 (maximum
speed).
Dependency:
Refer to: p0310, p1959
Refer to: F07984, F07985
Note:
In order to calculate the inertia, sudden speed changes are carried out - the specified value corresponds to the
lower speed setpoint. This value is increased by 20 % for the upper speed value. The q leakage inductance (refer to
p1959 bit 5) is determined at zero speed and at 50% of p1965 - however, with a maximum output frequency of 15
Hz and at a minimum of 10% of the rated motor speed.
p1967
Speed_ctrl_opt dynamic factor / n_opt dyn_factor
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1 [%]
Max
400 [%]
Factory setting
100 [%]
Description:
Sets the dynamic response factor for speed controller optimization.
Dependency:
For power units with a reduced DC link capacitance (e.g., PM250), the dynamic response of the controller is set to
40%.
Refer to: p1959
Refer to: F07985
Note:
For a rotating measurement, this parameter can be used to optimize the speed controller.
p1967 = 100 % --> speed controller optimization according to a symmetric optimum.
p1967 > 100 % --> optimization with a higher dynamic response (Kp higher, Tn lower).
r1968
Speed_ctrl_opt dynamic factor actual / n_opt dyn_fact act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Description:
Displays the dynamic factor which is actually achieved for the vibration test
Dependency:
Refer to: p1959, p1967
Factory setting
- [%]
Refer to: F07985
Note:
This dynamic factor only refers to the control mode of the speed controller set in p1960.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-247
Parameters
List of Parameters
r1969
Description:
Speed_ctrl_opt moment of inertia determined / n_opt M_inert det
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: 25_1
Unit selection: p0100
Min
- [kgm²]
Max
- [kgm²]
Factory setting
- [kgm²]
Displays the determined moment of inertia of the drive.
After it has been determined, the value is transferred to p0341, p0342.
Dependency:
IEC drives (p0100 = 0): unit kg m^2
NEMA drives (p0100 = 1): unit lb ft^2
Refer to: p0341, p0342, p1959
Refer to: F07984
r1970[0...1]
Speed_ctrl_opt vibration test vibration frequency determined / n_opt f_vibration
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Hz]
Max
- [Hz]
Description:
Displays the vibration frequencies determined by the vibration test.
Index:
[0] = Frequency low
[1] = Frequency high
Dependency:
Refer to: p1959
Factory setting
- [Hz]
Refer to: F07985
p1980[0...n]
PolID technique / PolID technique
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
1
Max
10
Factory setting
4
Description:
Sets the pole position identification technique.
Value:
1:
4:
6:
10:
Dependency:
Refer to: p1780
Note:
Voltage pulse technique (p1980 = 1, 4) cannot be applied to operation with sine-wave output filters (p0230).
r1984
PolID angular difference / PolID ang diff
Voltage pulsing 1st harmonics
Voltage pulsing 2-stage
Voltage pulsing 2-stage inverse
DC current injection
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [°]
Max
- [°]
Factory setting
- [°]
Description:
Displays the angular difference between the actual electrical commutation angle and the angle determined by the
pole position identification.
Dependency:
Refer to: p0325, p0329, p1980, r1985, r1987
Note:
When the pole position identification routine is executed several times, the spread of the measured values can be
determined using this value. At the same position, the spread should be less than 2 degrees electrical.
1-248
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r1985
Description:
PolID saturation curve / PolID sat_char
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [Arms]
Max
- [Arms]
Factory setting
- [Arms]
Displays the saturation characteristic of the pole position identification routine (saturation technique).
Displays the current characteristic of the pole position identification routine (elasticity technique).
Dependency:
Refer to: p0325, p0329, p1980, r1984, r1987
Note:
PolID: Pole position identification
Regarding the saturation technique:
The values for the characteristic of the last saturation-based pole position identification routine are output every 1
ms in order to record signals (e.g. trace).
r1987
Description:
PolID trigger characteristic / PolID trig_char
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the trigger characteristic of the pole position identification routine.
The values for the characteristic of the last pole position identification routine are output every 1 ms in order to
record signals (e.g. trace).
The values for trigger characteristic and saturation characteristic are always output in synchronism from a time perspective.
Dependency:
Refer to: p0325, p0329, p1980, r1984, r1985
Note:
PolID: Pole position identification
The following information and data can be taken from the trigger characteristic.
- the value -100% marks the angle at the start of the measurement.
- the value +100 % marks the commutation angle determined from the pole position identification routine.
p1999[0...n]
Ang. commutation offset calibr. and PollD scaling / Com_ang_offs scal
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
10 [%]
Max
5000 [%]
Factory setting
100 [%]
Description:
Sets the scaling for the runtime of the pole position identification technique in which the current is injected.
Dependency:
Caution:
Refer to: p0341, p0342
For p1999 > 100 % (setting large moments of inertia) the following applies:
There is no locked rotor monitoring (F07970 fault value 2).
Note:
For high moments of inertia, it is practical to scale the runtime of the calibration higher.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-249
Parameters
List of Parameters
p2000
Description:
Reference speed reference frequency / n_ref f_ref
Access level: 2
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
6.00 [rpm]
Max
210000.00 [rpm]
Factory setting
1500.00 [rpm]
Sets the reference quantity for speed and frequency.
All speeds or frequencies specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
The following applies: Reference frequency (in Hz) = reference speed (in ((rpm) / 60) x pole pair number).
Dependency:
This parameter is only updated during the automatic calculation (p0340 = 1, p3900 > 0) if motor commissioning was
carried out beforehand for drive data set zero. This means that the parameter is not locked against overwriting
using p0573 = 1.
Refer to: p2001, p2002, p2003, r2004, r3996
Notice:
When the reference speed / reference frequency is changed, short-term communication interruptions may occur.
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
Example 1:
The signal of an analog input (e.g. r0755[0]) is connected to a speed setpoint (e.g. p1070[0]). The actual percentage input value is cyclically converted into the absolute speed setpoint using the reference speed (p2000).
Example 2:
The setpoint from PROFIBUS (r2050[1]) is connected to a speed setpoint (e.g. p1070[0]). The actual input value is
cyclically converted into a percentage value via the pre-specified scaling 4000 hex. This percentage value is converted to the absolute speed setpoint via reference speed (p2000).
p2001
Description:
Reference voltage / Reference voltage
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10 [Vrms]
Max
100000 [Vrms]
Factory setting
1000 [Vrms]
Sets the reference quantity for voltages.
All voltages specified as relative value are referred to this reference quantity. This also applies for direct voltage values (= rms value) like the DC-link voltage.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
Dependency:
p2001 is only updated during automatic calculation (p0340 = 1, p3900 > 0) if motor commissioning has been carried
out first for drive data set zero and as a result overwriting of the parameter has not been blocked by setting p0573 =
1.
Refer to: r3996
Notice:
When the reference voltage is changed, short-term communication interruptions may occur.
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
For infeed units, the parameterized device supply voltage (p0210) is pre-assigned as the reference quantity.
Example:
The actual value of the DC link voltage (r0070) is connected to a test socket (e.g. p0771[0]). The actual voltage
value is cyclically converted into a percentage of the reference voltage (p2001) and output according to the parameterized scaling.
1-250
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2002
Description:
Reference current / I_ref
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.10 [Arms]
Max
100000.00 [Arms]
Factory setting
100.00 [Arms]
Sets the reference quantity for currents.
All currents specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
Dependency:
This parameter is only updated during the automatic calculation (p0340 = 1, p3900 > 0) if motor commissioning was
carried out beforehand for drive data set zero. This means that the parameter is not locked against overwriting
using p0573 = 1.
Refer to: r3996
Notice:
If various DDS are used with different motor data, then the reference quantities remain the same as these are not
changed over with the DDS. The resulting conversion factor must be taken into account.
Example:
p2002 = 100 A
Reference quantity 100 A corresponds to 100 %
p305[0] = 100 A
Rated motor current 100 A for MDS0 in DDS0 --> 100 % corresponds to 100 % of the rated motor current
p305[1] = 50 A
Rated motor current 50 A for MDS1 in DDS1 --> 100 % corresponds to 200 % of the rated motor current
When the reference current is changed, short-term communication interruptions may occur.
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
For infeed units, the rated line current, which is obtained from the rated power and parameterized rated line supply
voltage (p2002 = r0206 / p0210 / 1.73) is pre-assigned as the reference quantity.
Example:
The actual value of a phase current (r0069[0]) is connected to a test socket (e.g. p0771[0]). The actual current
value is cyclically converted into a percentage of the reference current (p2002) and output according to the parameterized scaling.
p2003
Description:
Reference torque / M_ref
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: 7_2
Unit selection: p0505
Min
0.01 [Nm]
Max
20000000.00 [Nm]
Factory setting
1.00 [Nm]
Sets the reference quantity for torque.
All torques specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
Dependency:
This parameter is only updated during the automatic calculation (p0340 = 1, p3900 > 0) if motor commissioning was
carried out beforehand for drive data set zero. This means that the parameter is not locked against overwriting
using p0573 = 1.
Refer to: r3996
Notice:
When the reference torque is changed, short-term communication interruptions may occur.
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
Example:
The actual value of the total torque (r0079) is connected to a test socket (e.g. p0771[0]). The actual torque is cyclically converted into a percentage of the reference torque (p2003) and output according to the parameterized scaling.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-251
Parameters
List of Parameters
r2004
Description:
Reference power / P_ref
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: 14_10
Unit selection: p0505
Min
- [kW]
Max
- [kW]
Factory setting
- [kW]
Displays the reference quantity for power.
All power ratings specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
Dependency:
This value is calculated as follows:
Infeed: Calculated from voltage times current.
Closed-loop control: Calculated from torque times speed.
Refer to: p2000, p2001, p2002, p2003
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
The reference power is calculated as follows:
- 2 * Pi * reference speed / 60 * reference torque (motor)
- reference voltage * reference current * root(3) (infeed)
p2005
Description:
Reference angle / Reference angle
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
90.00 [°]
Max
180.00 [°]
Factory setting
90.00 [°]
Sets the reference quantity for angle.
All angles specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
Dependency:
This parameter is only updated during the automatic calculation (p0340 = 1, p3900 > 0) if motor commissioning was
carried out beforehand for drive data set zero. This means that the parameter is not locked against overwriting
using p0573 = 1.
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
p2006
Reference temp / Ref temp
Description:
Access level: 3
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
50.00 [°C]
Max
300.00 [°C]
Factory setting
100.00 [°C]
Sets the reference quantity for temperature.
All temperatures specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
1-252
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2007
Description:
Reference acceleration / a_ref
Access level: 4
Calculated: p0340 = 1
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.01 [rev/s²]
Max
500000.00 [rev/s²]
Factory setting
0.01 [rev/s²]
Sets the reference quantity for acceleration rates.
All acceleration rates specified as relative value are referred to this reference quantity.
The reference quantity in this parameter corresponds to 100% or 4000 hex or 4000 0000 hex.
Dependency:
This parameter is only updated during the automatic calculation (p0340 = 1, p3900 > 0) if motor commissioning was
carried out beforehand for drive data set zero. This means that the parameter is not locked against overwriting
using p0573 = 1.
Note:
If a BICO interconnection is established between different physical quantities, then the particular reference quantities are used as internal conversion factor.
The reference acceleration is calculated as follows:
p2007 = p2000 / 1 [s]
p2010
Comm interface baud rate / Comm baud
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
4
Max
12
Description:
Sets the baud rate for the commissioning interface (USS, RS232).
Value:
4:
5:
6:
7:
8:
9:
10:
11:
12:
Note:
Commissioning interface
Factory setting
12
2400 baud
4800 baud
9600 baud
19200 baud
38400 baud
57600 baud
76800 baud
93750 baud
115200 baud
The parameter is not influenced by setting the factory setting.
p2011
Comm int address / Comm add
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
31
Description:
Sets the address for the commissioning interface (USS, RS232).
Note:
The parameter is not influenced by setting the factory setting.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
2
1-253
Parameters
List of Parameters
p2016[0...3]
Description:
CI: Comm IF USS PZD send word / Comm USS send word
Access level: 3
Calculated: -
Data type: U32 / Integer16
Can be changed: U, T
Scaling: 4000H
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Index:
Selects the PZD (actual values) to be sent via the commissioning interface USS.
The actual values are displayed on an intelligent operator panel (IOP).
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
r2019[0...7]
Comm int error statistics / Comm err
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Index:
Displays the receive errors at the commissioning interface (USS, RS232).
[0] = Number of error-free telegrams
[1] = Number of rejected telegrams
[2] = Number of framing errors
[3] = Number of overrun errors
[4] = Number of parity errors
[5] = Number of starting character errors
[6] = Number of checksum errors
[7] = Number of length errors
p2020
Field bus interface baud rate / Field bus baud
CU240B-2
Access level: 2
Calculated: -
Data type: Integer16
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
4
Max
13
Description:
Value:
Notice:
Note:
1-254
Factory setting
8
Sets the baud rate for the field bus interface (RS485).
4:
2400 baud
5:
4800 baud
6:
9600 baud
7:
19200 baud
8:
38400 baud
9:
57600 baud
10:
76800 baud
11:
93750 baud
12:
115200 baud
13:
187500 baud
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
For p0014 = 0, the following applies:
Before a changed setting becomes permanently effective, a non-volatile RAM to ROM data save is required. To do
this, set p0971 = 1 or p0014 = 1.
Fieldbus SS: Fieldbus interface
Changes only become effective after POWER ON.
The parameter is not influenced by setting the factory setting.
The parameter is set to the factory setting when the protocol is reselected.
When p2030 = 1 (USS), the following applies:
Min./max./factory setting: 4/13/8
When p2030 = 2 (MODBUS), the following applies:
Min./max./factory setting: 5/13/7
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2021
Field bus interface address / Field bus address
CU240B-2
Access level: 2
Calculated: -
Data type: Unsigned16
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0
Max
247
Description:
Dependency:
Notice:
Note:
Factory setting
0
Displays or sets the address for the fieldbus interface (RS485).
The address can be set as follows:
1) Using the address switch on the Control Unit.
--> p2021 displays the address setting.
--> A change only becomes effective after a POWER ON.
2) Using p2021
--> Only if an address of 0 or an address which is invalid for the fieldbus selected in p2030 has been set using the
address switch.
--> The address is saved in a non-volatile fashion using the function "copy from RAM to ROM".
--> A change only becomes effective after a POWER ON.
Refer to: p2030
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
For p0014 = 0, the following applies:
Before a changed setting becomes permanently effective, a non-volatile RAM to ROM data save is required. To do
this, set p0971 = 1 or p0014 = 1.
Changes only become effective after POWER ON.
The parameter is not influenced by setting the factory setting.
The parameter is set to the factory setting when the protocol is reselected.
When p2030 = 1 (USS), the following applies:
Min./max./factory setting: 0/30/0
When p2030 = 2 (MODBUS), the following applies:
Min./max./factory setting: 1/247/1
p2022
Field bus int USS PZD no. / Field bus USS PZD
CU240B-2
Access level: 2
Calculated: -
Data type: Unsigned16
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0
Max
8
Factory setting
2
Description:
Sets the number of 16-bit words in the PZD part of the USS telegram for the field bus interface.
Dependency:
Refer to: p2030
Note:
The parameter is not influenced by setting the factory setting.
p2023
Field bus int USS PKW no. / Field bus USS PKW
CU240B-2
Access level: 2
Calculated: -
Data type: Integer16
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0
Max
127
Factory setting
127
Description:
Sets the number of 16-bit words in the PKW part of the USS telegram for the field bus interface.
Value:
0:
3:
4:
127:
Dependency:
Refer to: p2030
Note:
The parameter is not influenced by setting the factory setting.
PKW 0 words
PKW 3 words
PKW 4 words
PKW variable
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-255
Parameters
List of Parameters
p2024[0...2]
Fieldbus interface times / Fieldbus times
CU240B-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
[0] 1000 [ms]
[1] 0 [ms]
[2] 0 [ms]
Description:
Sets the time values for the fieldbus interface.
The following applies for MODBUS:
p2024[0]: Maximum permissible telegram processing time of the MODBUS slave in which a reply is sent back to the
MODBUS master.
p2024[1]: Character delay time (time between individual characters in the telegram).
p2024[2]: Telegram pause time (pause time between two telegrams).
Index:
[0] = Max. processing time
[1] = Character delay time
[2] = Telegram pause time
Dependency:
Refer to: p2020, p2030
Note:
Re p2024[1,2] (MODBUS):
If the field bus baud rate is changed (p2020), the default time settings are restored.
The default setting is the time required for 1.5 characters (p2024[1]) or 3.5 characters (p2024[2]) (depending on the
set baud rate).
r2029[0...7]
Field bus int error statistics / Field bus error
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2
Can be changed: -
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the receive errors on the field bus interface (RS485).
Index:
[0] = Number of error-free telegrams
[1] = Number of rejected telegrams
[2] = Number of framing errors
[3] = Number of overrun errors
[4] = Number of parity errors
[5] = Number of starting character errors
[6] = Number of checksum errors
[7] = Number of length errors
p2030
Field bus int protocol selection / Field bus protocol
CU240B-2
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2
Can be changed: T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0
Max
2
Description:
Value:
Notice:
Note:
1-256
Factory setting
0
Sets the communication protocol for the field bus interface.
0:
No protocol
1:
USS
2:
MODBUS
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Changes only become effective after POWER ON.
The parameter is not influenced by setting the factory setting.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2030
Field bus int protocol selection / Field bus protocol
CU240B-2 DP
Access level: 1
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
3
Description:
Sets the communication protocol for the field bus interface.
Value:
0:
3:
Notice:
For p0014 = 1, the following applies:
No protocol
PROFIBUS
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
Changes only become effective after POWER ON.
The parameter is not influenced by setting the factory setting.
r2032
Master control, control word effective / PcCtrl STW eff
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the effective control word 1 (STW1) of the drive for the master control.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
Notice:
The master control only influences control word 1 and speed setpoint 1. Other control words/setpoints can be transferred from another automation device.
Note:
OC: Operating condition
p2037
PROFIdrive STW1.10 = 0 mode / PD STW1.10=0
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
2
Description:
Signal name
ON/OFF1
OC / OFF2
OC / OFF3
Operation enable
Ramp-function generator enable
Start ramp-function generator
Speed setpoint enable
Acknowledge fault
Jog bit 0
Jog bit 1
Master ctrl by PLC
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
FP
3030
3030
-
Factory setting
0
Sets the processing mode for PROFIdrive STW1.10 "master control by PLC".
Generally, control world 1 is received with the first receive word (PZD1) (this is in conformance to the PROFIdrive
profile). The behavior of STW1.10 = 0 corresponds to that of the PROFIdrive profile. For other applications that
deviate from this, the behavior can be adapted using this particular parameter.
Value:
0:
1:
2:
Freeze setpoints and continue to process sign-of-life
Freeze setpoints and sign-of-life
Setpoints are not frozen
Note:
If the STW1 is not transferred according to the PROFIdrive with PZD1 (with bit 10 "master control by PLC"), then
p2037 should be set to 2.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-257
Parameters
List of Parameters
p2038
PROFIdrive STW/ZSW interface mode / PD STW/ZSW IF mode
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
2
Description:
Factory setting
0
Sets the interface mode of the PROFIdrive control words and status words.
When selecting a telegram via p0922 (p2079), this parameter influences the device-specific assignment of the bits
in the control and status words.
Value:
0:
2:
SINAMICS
VIK-NAMUR
Dependency:
Refer to: p0922, p2079
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
- For p0922 (p2079) = 1, 350 ... 999, p2038 is automatically set to 0.
- For p0922 (p2079) = 20, p2038 is automatically set to 2.
It is not then possible to change p2038.
p2039
Description:
Select debug monitor interface / Debug monit select
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
The serial interface for the debug monitor is COM1 (commissioning interface, RS232) or COM2 (fieldbus interface,
RS485).
Value = 0: De-activated
Value = 1: COM1, commissioning protocol is de-activated
Value = 2: COM2, field bus is de-activated
Value = 3: Reserved
Note:
Value = 2 is only possible for Control Units with RS485 as a field bus interface.
p2040
Fieldbus interface monitoring time / Fieldbus t_monit
CU240B-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0 [ms]
Max
1999999 [ms]
Description:
Factory setting
100 [ms]
Sets the monitoring time to monitor the process data received via the fieldbus interface.
If no process data is received within this time, an appropriate message is output.
Dependency:
Refer to: F01910
Note:
0: The monitoring is de-activated.
1-258
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2042
PROFIBUS Ident Number / PB Ident No.
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Factory setting
0
Note:
Sets the PROFIBUS Ident Number (PNO-ID).
SINAMICS can be operated with various identities on PROFIBUS. This allows the use of a PROFIBUS GSD that is
independent of the device (e.g. PROFIdrive VIK-NAMUR with Ident Number 3AA0 hex).
0:
SINAMICS
1:
VIK-NAMUR
For p0014 = 1, the following applies:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Every change only becomes effective after a POWER ON.
r2043.0...2
BO: PROFIdrive PZD state / PD PZD state
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned8
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Value:
Notice:
Factory setting
-
Description:
Displays the PROFIdrive PZD state.
Bit field:
Bit
00
02
Dependency:
Refer to: p2044
Note:
When using the "setpoint failure" signal, the bus can be monitored and an application-specific response triggered
when the setpoint fails.
p2044
PROFIdrive fault delay / PD fault delay
CU240B-2 DP
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0 [s]
Max
100 [s]
Description:
Dependency:
Signal name
Setpoint failure
Fieldbus oper
1 signal
Yes
Yes
0 signal
No
No
Factory setting
0 [s]
Sets the delay time to initiate fault F01910 after a setpoint failure.
The time until the fault is initiated can be used by the application. This means that is is possible to respond to the
failure while the drive is still operational (e.g. emergency retraction).
Refer to: r2043
Refer to: F01910
p2047
PROFIBUS additional monitoring time / PB suppl t_monit
CU240B-2 DP
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0 [ms]
Max
20000 [ms]
Description:
Dependency:
Note:
FP
-
Factory setting
0 [ms]
Sets the additional monitoring time to monitor the process data received via PROFIBUS.
The additional monitoring time enables short bus faults to be compensated.
If no process data is received within this time, an appropriate message is output.
Refer to: F01910
For controller STOP, the additional monitoring time is not effective.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-259
Parameters
List of Parameters
r2050[0...7]
CO: PROFIBUS PZD receive word / PZD recv word
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: -
Scaling: 4000H
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Connector output to interconnect PZD (setpoints) with word format received from the fieldbus master.
Index:
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
p2051[0...7]
CI: PROFIdrive PZD send word / PZD send word
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Integer16
CU240E-2
Can be changed: U, T
Scaling: 4000H
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Selects the PZD (actual values) with word format to be sent to the fieldbus master.
Index:
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p2051[0...7]
CI: PROFIdrive PZD send word / PZD send word
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Integer16
CU240E-2 DP
Can be changed: U, T
Scaling: 4000H
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2089[0]
[1] 63[0]
[2...7] 0
Description:
Selects the PZD (actual values) with word format to be sent to the fieldbus master.
Index:
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
1-260
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2053[0...7]
PROFIdrive diagnostics send PZD word / Diag send word
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the PZD (actual values) with word format sent to the fieldbus master.
Index:
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
r2054
PROFIBUS status / PB status
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0
Max
4
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Description:
Status display for the PROFIBUS interface.
Value:
0:
1:
2:
3:
4:
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FP
-
Factory setting
-
OFF
No connection (search for baud rate)
Connection OK (baud rate found)
Cyclic connection with master (data exchange)
Cyclic data OK
r2055[0...2]
PROFIBUS diagnostics standard / PB diag standard
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Diagnostics display for the PROFIBUS interface.
Index:
[0] = Master bus address
[1] = Master input total length bytes
[2] = Master output total length bytes
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
-
1-261
Parameters
List of Parameters
r2074[0...7]
PROFIdrive diagnostics bus address PZD receive / Diag addr recv
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the PROFIBUS address of the sender from which the process data (PZD) is received.
Index:
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
Note:
Value range:
0 - 125: Bus address of the sender
255: Not assigned
r2075[0...7]
PROFIdrive diagnostics telegram offset PZD receive / Diag offs recv
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Index:
Note:
Factory setting
-
Displays the PZD byte offset in the PROFIdrive receive telegram (controller output).
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
Value range:
0 - 242: Byte offset
65535: not assigned
r2076[0...7]
PROFIdrive diagnostics telegram offset PZD send / Diag offs send
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Index:
Note:
1-262
Factory setting
-
Displays the PZD byte offset in the PROFIdrive send telegram (controller input).
[0] = PZD 1
[1] = PZD 2
[2] = PZD 3
[3] = PZD 4
[4] = PZD 5
[5] = PZD 6
[6] = PZD 7
[7] = PZD 8
Value range:
0 - 242: Byte offset
65535: not assigned
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2077[0...15]
PROFIBUS diagnostics peer-to-peer data transfer addresses / PB diag peer addr
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned8
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the addresses of the slaves (peers) where peer-to-peer data transfer has been configured via PROFIBUS.
p2079
PROFIdrive PZD telegram selection extended / PD PZD tel ext
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
1
Max
999
Description:
Factory setting
1
Dependency:
Sets the send and receive telegram.
Contrary to p0922, a telegram can be selected using p2079 and subsequently expanded.
For p0922 < 999 the following applies:
p2079 has the same value and is inhibited. All of the interconnections and extensions contained in the telegram are
inhibited.
For p0922 = 999 the following applies:
p2079 can be freely set. If p2079 is also set to 999, then all of the interconnections can be set.
For p0922 = 999 and p2079 < 999 the following applies:
The interconnections contained in the telegram are inhibited. However, the telegram can be extended.
1:
Standard telegram 1, PZD-2/2
20:
Standard telegram 20, PZD-2/6
350: SIEMENS telegram 350, PZD-4/4
352: SIEMENS telegram 352, PZD-6/6
353: SIEMENS telegram 353, PZD-2/2, PKW-4/4
354: SIEMENS telegram 354, PZD-6/6, PKW-4/4
999: Free telegram configuration with BICO
Refer to: p0922
p2080[0...15]
BI: Binector-connector converter status word 1 / Bin/con ZSW1
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Value:
Description:
Index:
Dependency:
Notice:
Factory setting
0
Selects bits to be sent to the PROFIdrive controller.
The individual bits are combined to form status word 1.
[0] = Bit 0
[1] = Bit 1
[2] = Bit 2
[3] = Bit 3
[4] = Bit 4
[5] = Bit 5
[6] = Bit 6
[7] = Bit 7
[8] = Bit 8
[9] = Bit 9
[10] = Bit 10
[11] = Bit 11
[12] = Bit 12
[13] = Bit 13
[14] = Bit 14
[15] = Bit 15
Refer to: p2088, r2089
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-263
Parameters
List of Parameters
p2080[0...15]
BI: Binector-connector converter status word 1 / Bin/con ZSW1
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 899.0
[1] 899.1
[2] 899.2
[3] 2139.3
[4] 899.4
[5] 899.5
[6] 899.6
[7] 2139.7
[8] 2197.7
[9] 899.9
[10] 2199.1
[11] 1407.7
[12] 899.12
[13] 2135.14
[14] 2197.3
[15] 2135.15
Description:
Selects bits to be sent to the PROFIdrive controller.
The individual bits are combined to form status word 1.
Index:
[0] = Bit 0
[1] = Bit 1
[2] = Bit 2
[3] = Bit 3
[4] = Bit 4
[5] = Bit 5
[6] = Bit 6
[7] = Bit 7
[8] = Bit 8
[9] = Bit 9
[10] = Bit 10
[11] = Bit 11
[12] = Bit 12
[13] = Bit 13
[14] = Bit 14
[15] = Bit 15
Dependency:
Refer to: p2088, r2089
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
1-264
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2081[0...15]
Description:
BI: Binector-connector converter status word 2 / Bin/con ZSW2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Selects bits to be sent to the PROFIdrive controller.
The individual bits are combined to form status word 2.
Index:
[0] = Bit 0
[1] = Bit 1
[2] = Bit 2
[3] = Bit 3
[4] = Bit 4
[5] = Bit 5
[6] = Bit 6
[7] = Bit 7
[8] = Bit 8
[9] = Bit 9
[10] = Bit 10
[11] = Bit 11
[12] = Bit 12
[13] = Bit 13
[14] = Bit 14
[15] = Bit 15
Dependency:
Refer to: p2088, r2089
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
p2082[0...15]
BI: Binector-connector converter status word 3 / Bin/con ZSW3
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Selects bits to be sent to the PROFIdrive controller.
The individual bits are combined to form free status word 3.
Index:
[0] = Bit 0
[1] = Bit 1
[2] = Bit 2
[3] = Bit 3
[4] = Bit 4
[5] = Bit 5
[6] = Bit 6
[7] = Bit 7
[8] = Bit 8
[9] = Bit 9
[10] = Bit 10
[11] = Bit 11
[12] = Bit 12
[13] = Bit 13
[14] = Bit 14
[15] = Bit 15
Dependency:
Refer to: p2088, r2089
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-265
Parameters
List of Parameters
p2083[0...15]
Description:
BI: Binector-connector converter status word 4 / Bin/con ZSW4
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Selects bits to be sent to the PROFIdrive controller.
The individual bits are combined to form free status word 4.
Index:
[0] = Bit 0
[1] = Bit 1
[2] = Bit 2
[3] = Bit 3
[4] = Bit 4
[5] = Bit 5
[6] = Bit 6
[7] = Bit 7
[8] = Bit 8
[9] = Bit 9
[10] = Bit 10
[11] = Bit 11
[12] = Bit 12
[13] = Bit 13
[14] = Bit 14
[15] = Bit 15
Dependency:
Refer to: p2088, r2089
p2084[0...15]
BI: Binector-connector converter status word 5 / Bin/con ZSW5
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Selects bits to be sent to the PROFIdrive controller.
The individual bits are combined to form free status word 5.
Index:
[0] = Bit 0
[1] = Bit 1
[2] = Bit 2
[3] = Bit 3
[4] = Bit 4
[5] = Bit 5
[6] = Bit 6
[7] = Bit 7
[8] = Bit 8
[9] = Bit 9
[10] = Bit 10
[11] = Bit 11
[12] = Bit 12
[13] = Bit 13
[14] = Bit 14
[15] = Bit 15
Dependency:
Refer to: p2088, r2089
1-266
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2088[0...4]
Invert binector-connector converter status word / Bin/con ZSW inv
CU240B-2
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0000 0000 0000 bin
Description:
Index:
Setting to invert the individual binector inputs of the binector connector converter.
[0] = Status word 1
[1] = Status word 2
[2] = Free status word 3
[3] = Free status word 4
[4] = Free status word 5
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Dependency:
Refer to: p2080, p2081, p2082, p2083, r2089
p2088[0...4]
Invert binector-connector converter status word / Bin/con ZSW inv
CU240B-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
0 signal
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
FP
-
Factory setting
[0] 1010 1000 0000 0000 bin
[1...4] 0000 0000 0000 0000 bin
Description:
Index:
Bit field:
Dependency:
Setting to invert the individual binector inputs of the binector connector converter.
[0] = Status word 1
[1] = Status word 2
[2] = Free status word 3
[3] = Free status word 4
[4] = Free status word 5
Bit Signal name
1 signal
0 signal
00 Bit 0
Inverted
Not inverted
01 Bit 1
Inverted
Not inverted
02 Bit 2
Inverted
Not inverted
03 Bit 3
Inverted
Not inverted
04 Bit 4
Inverted
Not inverted
05 Bit 5
Inverted
Not inverted
06 Bit 6
Inverted
Not inverted
07 Bit 7
Inverted
Not inverted
08 Bit 8
Inverted
Not inverted
09 Bit 9
Inverted
Not inverted
10 Bit 10
Inverted
Not inverted
11 Bit 11
Inverted
Not inverted
12 Bit 12
Inverted
Not inverted
13 Bit 13
Inverted
Not inverted
14 Bit 14
Inverted
Not inverted
15 Bit 15
Inverted
Not inverted
FP
-
Refer to: p2080, p2081, p2082, p2083, r2089
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-267
Parameters
List of Parameters
r2089[0...4]
CO: Send binector-connector converter status word / Bin/con ZSW send
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Connector output to interconnect the status words to a PZD send word.
Index:
[0] = Status word 1
[1] = Status word 2
[2] = Free status word 3
[3] = Free status word 4
[4] = Free status word 5
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Dependency:
Refer to: p2051, p2080, p2081, p2082, p2083
Note:
r2089 together with p2080 to p2084 forms five binector-connector converters.
r2090.0...15
BO: PROFIdrive PZD1 receive bit-serial / PZD1 recv bitw
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
FP
-
Factory setting
-
Description:
Binector output for bit-serial interconnection of PZD1 (normally control word 1) received from the PROFIdrive controller.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
1-268
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2091.0...15
BO: PROFIdrive PZD2 receive bit-serial / PZD2 recv bitw
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Binector output for bit-serial interconnection of PZD2 received from the PROFIdrive controller.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
r2092.0...15
BO: PROFIdrive PZD3 receive bit-serial / PZD3 recv bitw
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Binector output for bit-serial interconnection of PZD3 received from the PROFIdrive controller.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
FP
-
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FP
-
1-269
Parameters
List of Parameters
r2093.0...15
BO: PROFIdrive PZD4 receive bit-serial / PZD4 recv bitw
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Binector output for bit-serial interconnection of PZD4 (normally control word 2) received from the PROFIdrive controller.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
r2094.0...15
BO: Connector-binector converter binector output / Con/bin outp
Description:
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
FP
-
Factory setting
-
Binector output for bit-serial onward interconnection of a PZD word received from the PROFIdrive controller.
The PZD is selected via p2099[0].
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Dependency:
Refer to: p2099
1-270
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2095.0...15
Description:
BO: Connector-binector converter binector output / Con/bin outp
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Binector output for bit-serial interconnection of a PZD word received from the PROFIdrive controller.
The PZD is selected via p2099[1].
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Dependency:
Refer to: p2099
p2098[0...1]
Description:
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FP
-
Inverter connector-binector converter binector output / Con/bin outp inv
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0000 0000 0000 bin
Setting to invert the individual binector outputs of the connector-binector converter.
Using p2098[0], the signals of CI: p2099[0] are influenced.
Using p2098[1], the signals of CI: p2099[1] are influenced.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Signal name
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
Dependency:
Refer to: r2094, r2095, p2099
1 signal
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
Inverted
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
Not inverted
FP
-
1-271
Parameters
List of Parameters
p2099[0...1]
Description:
CI: Connector-binector converter signal source / Con/bin S_src
Access level: 3
Calculated: -
Data type: U32 / Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the connector-binector converter.
A PZD receive word can be selected as signal source. The signals are available to be serially passed-on (interconnection).
Dependency:
Refer to: r2094, r2095
Note:
From the signal source set via the connector input, the corresponding lower 16 bits are converted.
p2099[0...1] together with r2094.0...15 and r2095.0...15 forms two connector-binector converters:
Connector input p2099[0] to binector output in r2094.0...15
Connector input p2099[1] to binector output in r2095.0...15
p2100[0...19]
Setting the fault number for fault response / F_no F response
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Description:
Selects the faults for which the fault response should be changed
Dependency:
The fault is selected and the required response is set under the same index.
Factory setting
0
Refer to: p2101
Notice:
For the following cases, it is not possible to re-parameterize the fault response to a fault:
- if there is no existing fault number.
- the message type is not "fault" (F).
- when a fault is present.
1-272
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2101[0...19]
Setting the fault response / Fault response
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
6
Description:
Sets the fault response for the selected fault.
Value:
0:
1:
2:
3:
5:
6:
Dependency:
The fault is selected and the required response is set under the same index.
Factory setting
0
NONE
OFF1
OFF2
OFF3
STOP2
Internal armature short-circuit / DC braking
Refer to: p2100
Notice:
It is not possible to re-parameterize the response to a specific fault for faults that are already present (queued).
Note:
The fault response can only be changed for faults with the appropriate identification.
Example:
F12345 and fault response = NONE (OFF1, OFF2)
--> The fault response NONE can be changed to OFF1 or OFF2.
Re value = 1 (OFF1):
Braking along the ramp-function generator down ramp followed by a pulse inhibit.
Re value = 2 (OFF2):
Internal/external pulse inhibit.
Re value = 3 (OFF3):
Braking along the OFF3 down ramp followed by a pulse inhibit.
Re value = 5 (STOP2):
n_set = 0
Re value = 6 (armature short-circuit, internal/DC braking):
This value can only be set for all drive data sets when p1231 = 4.
a) DC braking is not possible for synchronous motors.
b) DC braking is possible for induction motors.
p2103[0...n]
BI: 1. Acknowledge faults / 1. Acknowledge
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 722.2
[1] 0
[2] 0
[3] 0
Description:
Sets the first signal source to acknowledge faults.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
A fault acknowledgement is triggered with a 0/1 signal.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-273
Parameters
List of Parameters
p2103[0...n]
BI: 1. Acknowledge faults / 1. Acknowledge
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
[0] 2090.7
[1] 722.2
[2] 2090.7
[3] 2090.7
Description:
Sets the first signal source to acknowledge faults.
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
A fault acknowledgement is triggered with a 0/1 signal.
p2104[0...n]
BI: 2. Acknowledge faults / 2. Acknowledge
CU240B-2
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
CU240E-2 F
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the second signal source to acknowledge faults.
Note:
A fault acknowledgement is triggered with a 0/1 signal.
p2104[0...n]
BI: 2. Acknowledge faults / 2. Acknowledge
CU240B-2 DP
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 DP
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the second signal source to acknowledge faults.
Note:
A fault acknowledgement is triggered with a 0/1 signal.
p2105[0...n]
BI: 3. Acknowledge faults / 3. Acknowledge
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the third signal source to acknowledge faults.
Note:
A fault acknowledgement is triggered with a 0/1 signal.
1-274
Factory setting
[0] 722.2
[1] 0
[2] 0
[3] 0
Factory setting
0
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2106[0...n]
BI: External fault 1 / External fault 1
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Dependency:
Sets the signal source for external fault 1.
Refer to: F07860
Note:
An external fault is triggered with a 1/0 signal.
p2107[0...n]
BI: External fault 2 / External fault 2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for external fault 2.
Dependency:
Refer to: F07861
Note:
An external fault is triggered with a 1/0 signal.
p2108[0...n]
Description:
Factory setting
1
Factory setting
1
BI: External fault 3 / External fault 3
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the signal source for external fault 3.
External fault 3 is initiated by the following AND logic operation:
- BI: p2108 negated
- BI: p3111
- BI: p3112 negated
Dependency:
Refer to: p3110, p3111, p3112
Refer to: F07862
Note:
r2109[0...63]
An external fault is triggered with a 1/0 signal.
Fault time removed in milliseconds / t_flt resolved ms
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Factory setting
- [ms]
Description:
Displays the system runtime in milliseconds when the fault was removed.
Dependency:
Refer to: r0945, r0947, r0948, r0949, r2130, r2133, r2136
Notice:
The time comprises r2136 (days) and r2109 (milliseconds).
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the fault buffer and the assignment of the indices is shown in r0945.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-275
Parameters
List of Parameters
r2110[0...63]
Alarm number / Alarm number
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
This parameter is identical to r2122.
p2111
Alarm counter / Alarm counter
Factory setting
-
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Description:
Number of alarms that have occurred after the last reset.
Dependency:
When p2111 is set to 0, the following is initiated:
Factory setting
0
- all of the alarms of the alarm buffer that have gone [0...7] are transferred into the alarm history [8...63].
- the alarm buffer [0...7] is deleted.
Refer to: r2110, r2122, r2123, r2124, r2125
Note:
The parameter is reset to 0 at POWER ON.
p2112[0...n]
BI: External alarm 1 / External alarm 1
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for external alarm 1.
Dependency:
Refer to: A07850
Note:
An external alarm is triggered with a 1/0 signal.
r2114[0...1]
System runtime total / Sys runtime tot
Description:
Factory setting
1
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the total system runtime for the drive unit.
The time comprises r2114[0] (milliseconds) and r2114[1] (days).
After r2114[0] has reached a value of 86.400.000 ms (24 hours) this value is reset and r2114[1] is incremented.
Index:
[0] = Milliseconds
[1] = Days
Dependency:
Refer to: r0948, r2109, r2123, r2125, r2130, r2136, r2145, r2146
Note:
When the electronic power supply is switched out, the counter values are saved.
After the drive unit is powered up, the counter continues to run with the last value that was saved.
1-276
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2116[0...n]
BI: External alarm 2 / External alarm 2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for external alarm 2.
Dependency:
Refer to: A07851
Note:
An external alarm is triggered with a 1/0 signal.
p2117[0...n]
Factory setting
1
BI: External alarm 3 / External alarm 3
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Description:
Sets the signal source for external alarm 3.
Dependency:
Refer to: A07852
Note:
An external alarm is triggered with a 1/0 signal.
p2118[0...19]
Sets the message number for message type. / Msg_no Msg_type
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Factory setting
0
Description:
Selects faults or alarms for which the message type should be changed.
Dependency:
Selects the fault or alarm selection and sets the required type of message realized under the same index.
Refer to: p2119
Notice:
It is not possible to re-parameterize the message type in the following cases:
- if there is no existing message number.
- if a message is present.
p2119[0...19]
Setting the message type / Message type
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
3
Factory setting
1
Description:
Sets the message type for the selected fault or alarm.
Value:
1:
2:
3:
Dependency:
Selects the fault or alarm selection and sets the required type of message realized under the same index.
Fault (F)
Alarm (A)
No message (N)
Refer to: p2118
Notice:
It is not possible to re-parameterize the message type for the existing faults or alarms.
Note:
The message type can only be changed for messages with the appropriate identification.
Example:
F12345(A) --> Fault F12345 can be changed to alarm A12345.
In this case, the message number that may be possibly entered in p2100[0...19] and p2126[0...19] is automatically
removed.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-277
Parameters
List of Parameters
r2120
CO: Sum of fault and alarm buffer changes / Sum buffer changed
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the sum of all of the fault and alarm buffer changes in the drive unit.
Dependency:
Refer to: r0944, r2121
r2121
CO: Counter, alarm buffer changes / Alrm buff changed
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
This counter is incremented every time the alarm buffer changes.
Dependency:
Refer to: r2110, r2122, r2123, r2124, r2125
r2122[0...63]
Alarm code / Alarm code
Factory setting
-
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the number of alarms that have occurred.
Dependency:
Refer to: r2110, r2123, r2124, r2125, r2134, r2145, r2146
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
Alarm buffer structure (general principle):
r2122[0], r2124[0], r2123[0], r2125[0] --> alarm 1 (the oldest)
...
r2122[7], r2124[7], r2123[7], r2125[7] --> Alarm 8 (the latest)
When the alarm buffer is full, the alarms that have gone are entered into the alarm history:
r2122[8], r2124[8], r2123[8], r2125[8] --> Alarm 1 (the latest)
...
r2122[63], r2124[63], r2123[63], r2125[63] --> alarm 56 (the oldest)
r2123[0...63]
Alarm time received in milliseconds / t_alarm recv ms
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Factory setting
- [ms]
Description:
Displays the system runtime in milliseconds when the alarm occurred.
Dependency:
Refer to: r2110, r2122, r2124, r2125, r2134, r2145, r2146
Notice:
The time comprises r2145 (days) and r2123 (milliseconds).
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
1-278
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2124[0...63]
Alarm value / Alarm value
Access level: 3
Calculated: -
Data type: Integer32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays additional information about the active alarm (as integer number).
Dependency:
Refer to: r2110, r2122, r2123, r2125, r2134, r2145, r2146
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
r2125[0...63]
Alarm time removed in milliseconds / t_alarm res ms
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Factory setting
- [ms]
Description:
Displays the system runtime in milliseconds when the alarm was cleared.
Dependency:
Refer to: r2110, r2122, r2123, r2124, r2134, r2145, r2146
Notice:
The time comprises r2146 (days) and r2125 (milliseconds).
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
p2126[0...19]
Setting fault number for acknowledge mode / Fault_no ackn_mode
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Factory setting
0
Description:
Selects the faults for which the acknowledge mode is to be changed
Dependency:
Selects the faults and sets the required acknowledge mode realized under the same index
Refer to: p2127
Notice:
It is not possible to re-parameterize the acknowledge mode of a fault in the following cases:
- if there is no existing fault number.
- the message type is not "fault" (F).
- when a fault is present.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-279
Parameters
List of Parameters
p2127[0...19]
Description:
Value:
Dependency:
Notice:
Note:
p2128[0...15]
Sets acknowledgement mode / Acknowledge mode
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2
Factory setting
1
Sets the acknowledge mode for selected fault.
1:
Acknowledgment only using POWER ON
2:
Ack IMMEDIATELY after the fault cause has been removed
Selects the faults and sets the required acknowledge mode realized under the same index
Refer to: p2126
It is not possible to re-parameterize the acknowledge mode of a fault in the following cases:
- if there is no existing fault number.
- the message type is not "fault" (F).
- when a fault is present.
The acknowledge mode can only be changed for faults with the appropriate identification.
Example:
F12345 and acknowledge mode = IMMEDIATE (POWER ON)
--> The acknowledge mode can be changed from IMMEDIATELY to POWER ON.
Selecting fault/alarm code for trigger / Message trigger
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
65535
Factory setting
0
Description:
Dependency:
Selects faults or alarms which can be used as trigger.
Refer to: r2129
r2129.0...15
CO/BO: Trigger word for faults and alarms / Trigger word
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Trigger signal for the selected faults and alarms
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Dependency:
If one of the faults or alarms selected in p2128[n] occurs, then the particular bit of this binector output is set.
Refer to: p2128
CO: r2129 = 0 --> None of the selected messages has occurred.
CO: r2129 > 0 --> At least one of the selected messages has occurred.
Note:
1-280
Signal name
Trigger signal p2128[0]
Trigger signal p2128[1]
Trigger signal p2128[2]
Trigger signal p2128[3]
Trigger signal p2128[4]
Trigger signal p2128[5]
Trigger signal p2128[6]
Trigger signal p2128[7]
Trigger signal p2128[8]
Trigger signal p2128[9]
Trigger signal p2128[10]
Trigger signal p2128[11]
Trigger signal p2128[12]
Trigger signal p2128[13]
Trigger signal p2128[14]
Trigger signal p2128[15]
1 signal
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
0 signal
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2130[0...63]
Fault time received in days / t_fault recv days
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the system runtime in days when the fault occurred.
Dependency:
Refer to: r0945, r0947, r0948, r0949, r2109, r2133, r2136
Notice:
The time comprises r2130 (days) and r0948 (milliseconds).
Factory setting
-
The value displayed in p2130 refers to 01.01.1970.
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
r2131
CO: Actual fault code / Actual fault code
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Dependency:
Note:
Displays the code of the oldest active fault.
Refer to: r3131, r3132
0: No fault present.
r2132
CO: Actual alarm code / Actual alarm code
Factory setting
-
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Note:
Displays the code of the last alarm that occurred.
0: No alarm present.
r2133[0...63]
Fault value for float values / Fault val float
Factory setting
-
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays additional information about the fault that occurred for float values.
Dependency:
Refer to: r0945, r0947, r0948, r0949, r2109, r2130, r2136
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
r2134[0...63]
Alarm value for float values / Alarm value float
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays additional information about the active alarm for float values.
Dependency:
Refer to: r2110, r2122, r2123, r2124, r2125, r2145, r2146
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-281
Parameters
List of Parameters
r2135.12...15
CO/BO: Status word faults/alarms 2 / ZSW fault/alarm 2
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the second status word of faults and alarms.
Bit field:
Bit
12
13
14
15
r2136[0...63]
Signal name
Fault motor overtemperature
Fault power unit thermal overload
Alarm motor overtemperature
Alarm power unit thermal overload
1 signal
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
Fault time removed in days / t_flt resolv. days
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the system runtime in days when the fault was removed.
Dependency:
Refer to: r0945, r0947, r0948, r0949, r2109, r2130, r2133
Notice:
The time comprises r2136 (days) and r2109 (milliseconds).
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
r2138.7...15
CO/BO: Control word faults/alarms / STW fault/alarm
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the control word of the faults and alarms.
Bit field:
Bit
07
10
11
12
13
14
15
Dependency:
Refer to: p2103, p2104, p2105, p2106, p2107, p2108, p2112, p2116, p2117, p3110, p3111, p3112
1-282
FP
-
Signal name
Acknowledge fault
External alarm 1 (A07850) effective
External alarm 2 (A07851) effective
External alarm 3 (A07852) effective
External fault 1 (F07860) effective
External fault 2 (F07861) effective
External fault 3 (F07862) effective
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2139.0...12
CO/BO: Status word faults/alarms 1 / ZSW fault/alarm 1
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the first status word of faults and alarms.
Bit field:
Bit
00
01
03
06
07
08
11
12
Note:
Re bit 03, 07:
Signal name
Being acknowledged
Acknowledgment required
Fault present
Internal message 1 present
Alarm present
Internal message 2 present
Alarm class bit 0
Alarm class bit 1
Factory setting
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
High
High
0 signal
No
No
No
No
No
No
Low
Low
FP
-
These bits are set if at least one fault/alarm occurs. Data is entered into the fault/alarm buffer with delay. This is the
reason that the fault/alarm buffer should only be read if, after "fault present"/"alarm present" has occurred, a change
in the buffer was also detected (r0944, r9744, r2121).
Re bit 06, 08:
These status bits are used for internal diagnostic purposes only.
Re bit 11, 12:
These status bits are used for the classification of internal alarm classes and are intended for diagnostic purposes
only on certain automation systems with integrated SINAMICS functionality.
p2140[0...n]
Description:
Hysteresis speed 2 / n_hysteresis 2
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
300.00 [rpm]
Dependency:
Sets the hysteresis speed (bandwidth) for the following signals:
"|n_act| < = speed threshold value 2" (BO: r2197.1)
"|n_act| > speed threshold value 2" (BO: r2197.2)
Refer to: p2155, r2197
p2141[0...n]
Speed threshold 1 / n_thresh val 1
Description:
Dependency:
Factory setting
90.00 [rpm]
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
5.00 [rpm]
Sets the speed threshold value for the signal "f or n comparison value reached or exceeded" (BO: r2199.1).
Refer to: p2142, r2199
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-283
Parameters
List of Parameters
p2142[0...n]
Hysteresis speed 1 / n_hysteresis 1
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
300.00 [rpm]
Factory setting
2.00 [rpm]
Description:
Sets the hysteresis speed (bandwidth) for the signal "f or n / v comparison value reached or exceeded" (BO:
r2199.1).
Dependency:
Refer to: p2141, r2199
p2144[0...n]
BI: Motor stall monitoring enable (negated) / Mot stall enab neg
Access level: 4
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the negated enable (0 = enable) of the motor stall monitoring.
Dependency:
Refer to: p2163, p2164, p2166, r2197, r2198
Refer to: F07900
Note:
If the enable signal is connected to r2197.7 then the stall signal is suppressed if there is no speed setpoint - actual
value deviation.
r2145[0...63]
Alarm time received in days / t_alarm recv days
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the system runtime in days when the alarm occurred.
Dependency:
Refer to: r2110, r2122, r2123, r2124, r2125, r2134, r2146
Notice:
The time comprises r2145 (days) and r2123 (milliseconds).
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
r2146[0...63]
Alarm time removed in days / t_alarm res days
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the system runtime in days when the alarm was cleared.
Dependency:
Refer to: r2110, r2122, r2123, r2124, r2125, r2134, r2145
Notice:
The time comprises r2146 (days) and r2125 (milliseconds).
Note:
The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
1-284
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2148[0...n]
Description:
BI: RFG active / RFG active
Access level: 3
Calculated: p0340 = 1,3,5
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the signal "ramp-function generator active" for the following signals/messages:
"Speed setpoint - actual value deviation within tolerance t_on" (BO: r2199.4)
"Ramp-up/ramp-down completed" (BO: r2199.5)
Notice:
The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note:
The binector input is automatically interconnected to r1199.2 as a default setting.
p2149[0...n]
Monitoring configuration / Monit config
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1001 bin
Description:
Sets the configuration for messages and monitoring functions.
Bit field:
Bit
00
01
03
Dependency:
Refer to: r2197
Signal name
Enable alarm A07903
Load monitoring only in the 1st quadrant
n_act > p2155 own hysteresis
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
8010
8013
8010
Refer to: A07903
Note:
Re bit 00:
Alarm A07903 is output when the bit is set with r2197.7 = 0 (n_set <> n_act).
Re bit 01:
When the bit is set, load monitoring is only carried out in the 1st quadrant as a result of the positive characteristic
parameters (p2182 ... p2190).
Re bit 03:
When the bit is set, r2197 bit 1 and bit 2 are determined via separate hystereses.
p2150[0...n]
Description:
Hysteresis speed 3 / n_hysteresis 3
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
300.00 [rpm]
Factory setting
2.00 [rpm]
Sets the hysteresis speed (bandwidth) for the following signals:
"|n_act| < speed threshold value 3" (BO: r2199.0)
"n_set >= 0" (BO: r2198.5)
"n_act >= 0" (BO: r2197.3)
Dependency:
Refer to: p2161, r2197, r2199
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-285
Parameters
List of Parameters
p2151[0...n]
Description:
CI: Speed setpoint for messages/signals / n_set for msg
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1170[0]
Sets the signal source for the speed setpoint for the following messages:
"Speed setpoint - actual value deviation within tolerance t_off" (BO: r2197.7)
"Ramp-up/ramp-down completed" (BO: r2199.5)
"|n_set| < p2161" (BO: r2198.4)
"n_set > 0" (BO: r2198.5)
Dependency:
p2152[0...n]
Refer to: r2197, r2198, r2199
Delay for comparison n > n_max / Del n > n_max
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Description:
Delay time for the comparison of the speed with the maximum speed.
Dependency:
Refer to: p1082, r1084, r1087, p2162
p2153[0...n]
Speed actual value filter time constant / n_act_filt T
Description:
Factory setting
200 [ms]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
1000000 [ms]
Factory setting
0 [ms]
Sets the time constant of the PT1 element to smooth the speed / velocity actual value.
The smoothed actual speed/velocity is compared with the threshold values and is only used for messages and signals.
Dependency:
p2155[0...n]
Description:
Refer to: r2169
Speed threshold 2 / n_thresh val 2
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
900.00 [rpm]
Sets the speed threshold value for the following messages:
"|n_act| < = speed threshold value 2" (BO: r2197.1)
"|n_act| > speed threshold value 2" (BO: r2197.2)
Dependency:
1-286
Refer to: p2140, r2197
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2156[0...n]
On delay, comparison value reached / t_on cmpr val rchd
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
10000.0 [ms]
Factory setting
0.0 [ms]
Description:
Sets the switch-in delay time for the signal "comparison value reached" (BO: r2199.1).
Dependency:
Refer to: p2141, p2142, r2199
p2157[0...n]
Description:
Speed threshold 5 / n_thresh val 5
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
900.00 [rpm]
Sets the speed threshold value for the following messages:
"|n_act| < = speed threshold value 5" (BO: r2198.0)
"|n_act| > speed threshold value 5" (BO: r2198.1)
Dependency:
Refer to: p2150, p2158
p2158[0...n]
Delay for n_act comparison with speed threshold value 5 / Del compar n_5
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
10 [ms]
Description:
Delay time for the comparison of the speed with the speed threshold value 5 (P2157).
Dependency:
Refer to: p2150, p2157
p2159[0...n]
Speed threshold 6 / n_thresh val 6
Description:
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
900.00 [rpm]
Sets the speed threshold value for the following messages:
"|n_act| < = speed threshold value 6" (BO: r2198.2)
"|n_act| > speed threshold value 6" (BO: r2198.3)
Dependency:
p2160[0...n]
Refer to: p2150, p2160
Delay for n_act comparison with speed threshold value 6 / Del compar n_6
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
10 [ms]
Description:
Sets the delay time for the comparison of the speed with the speed threshold value 6 (p2159).
Dependency:
Refer to: p2150, p2159
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-287
Parameters
List of Parameters
p2161[0...n]
Speed threshold 3 / n_thresh val 3
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
5.00 [rpm]
Description:
Sets the speed threshold value for the signal "|n_act| < speed threshold value 3" (BO: r2199.0).
Dependency:
Refer to: p2150, r2199
p2162[0...n]
Hysteresis speed n_act > n_max / Hyst n_act>n_max
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
60000.00 [rpm]
Factory setting
0.00 [rpm]
Description:
Sets the hysteresis speed (bandwidth) for the signal "n_act > n_max" (BO: r2197.6).
Dependency:
Refer to: r1084, r1087, r2197
Notice:
For p0322 = 0, the following applies: p2162 <= 0.1 * p0311
For p0322 > 0, the following applies: p2162 <= 1.02 * p0322 - p1082
If one of the conditions is violated, p2162 is appropriately and automatically reduced when exiting the commissioning mode.
Note:
For a negative speed limit (r1087) the hysteresis is effective below the limit value and for a positive speed limit
(r1084) above the limit value.
If significant overshoot occurs in the maximum speed range (e.g. due to load shedding), you are advised to
increase the dynamic response of the speed controller (if possible). If this is insufficient, the hysteresis p2162 can
only be increased by more than 10% of the rated speed when the maximum speed (p0322) of the motor is sufficiently greater than the speed limit p1082.
p2163[0...n]
Speed threshold 4 / n_thresh val 4
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
90.00 [rpm]
Description:
Sets the speed threshold value for the "speed setpoint - actual value deviation in tolerance t_off" signal/message
(BO: r2197.7).
Dependency:
Refer to: p2164, p2166, r2197
p2164[0...n]
Hysteresis speed 4 / n_hysteresis 4
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
200.00 [rpm]
Factory setting
2.00 [rpm]
Description:
Sets the hysteresis speed (bandwidth) for the "speed setpoint - actual value deviation in tolerance t_off" signal/message (BO: r2197.7).
Dependency:
Refer to: p2163, p2166, r2197
1-288
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2166[0...n]
Off delay n_act = n_set / t_del_off n_i=n_so
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
10000.0 [ms]
Factory setting
200.0 [ms]
Description:
Sets the switch-off delay time for the "speed setpoint - actual value deviation in tolerance t_off" signal/message
(BO: r2197.7).
Dependency:
Refer to: p2163, p2164, r2197
p2167[0...n]
Switch-on delay n_act = n_set / t_on n_act=n_set
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
10000.0 [ms]
Factory setting
200.0 [ms]
Description:
Sets the switch-on delay for the "speed setpoint - actual value deviation in tolerance t_on" signal/message (BO:
r2199.4).
r2169
CO: Actual speed smoothed signals / n_act smth message
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Displays the smoothed actual speed for messages/signals.
Dependency:
Refer to: p2153
p2170[0...n]
Current threshold value / I_thres
Description:
Factory setting
- [rpm]
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2002
Data set: DDS, p0180
Units group: 6_2
Unit selection: p0505
Min
0.00 [Arms]
Max
10000.00 [Arms]
Factory setting
0.00 [Arms]
Sets the absolute current threshold for the messages.
"I_act >= I_threshold p2170" (BO: r2197.8)
"I_act < I_threshold p2170" (BO: r2198.8)
Dependency:
p2171[0...n]
Refer to: p2171
Current threshold value reached delay time / t_del I_thresh rch
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
10 [ms]
Description:
Sets the delay time for the comparison of the current actual value (r0068) with the current threshold value (p2170).
Dependency:
Refer to: p2170
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-289
Parameters
List of Parameters
p2172[0...n]
Description:
DC link voltage, threshold value / Vdc thresh val
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2001
Data set: DDS, p0180
Units group: 5_2
Unit selection: p0505
Min
0 [V]
Max
2000 [V]
Factory setting
800 [V]
Sets the DC link voltage threshold value for the following messages:
"Vdc_act <= Vdc_threshold p2172" (BO: r2197.9)
"Vdc_act > Vdc_threshold p2172" (BO: r2197.10)
Dependency:
Refer to: p2173
p2173[0...n]
DC link voltage comparison delay time / t_del Vdc
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
10 [ms]
Description:
Sets the delay time for the comparison of the DC link voltage r0070 with the threshold value p2172.
Dependency:
Refer to: p2172
p2174[0...n]
Torque threshold value 1 / M_thresh val 1
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Factory setting
5.13 [Nm]
Dependency:
Sets the torque threshold value for the messages:
"Torque setpoint < torque threshold value 1 and n_set reached" (BO: r2198.9)
"Torque setpoint < torque threshold value 1" (BO: r2198.10)
"Torque setpoint > torque threshold value 1" (BO: r2198.13)
Refer to: p2195, r2198
p2175[0...n]
Motor locked speed threshold / Mot lock n_thresh
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
120.00 [rpm]
Description:
Dependency:
Note:
Sets the speed threshold for the message "Motor locked" (BO: r2198.6).
Refer to: p0500, p2177, r2198
The following applies for sensorless vector control:
At low speeds in open-loop speed controlled operation (see p1755, p1756), a locked motor cannot be detected.
p2176[0...n]
Torque threshold value comparison delay time / M_thrsh comp T_del
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Factory setting
200 [ms]
Description:
Sets the delay time for the comparison of the torque actual value (r0080) with torque threshold value 1 (p2174).
Dependency:
Refer to: p2174
1-290
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2177[0...n]
Motor locked delay time / Mot lock t_del
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
65.000 [s]
Description:
Sets the delay time for the message "Motor locked" (BO: r2198.6).
Dependency:
Refer to: p0500, p2175, r2198
Note:
The following applies for sensorless vector control:
Factory setting
3.000 [s]
At low speeds a locked motor can only be detected if no change is made to open-loop speed controlled operation. If
this is the case, the value in p2177 must be reduced accordingly before time p2177 has elapsed in order to detect
the locked state reliably.
p2178[0...n]
Motor stalled delay time / Mot stall t_del
Access level: 3
Calculated: p0340 = 1,3
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.000 [s]
Max
10.000 [s]
Factory setting
0.010 [s]
Description:
Sets the delay time for the message "Motor stalled" (BO: r2198.7).
Dependency:
Refer to: r2198
Note:
In the open-loop speed controlled operating range (see p1755, p1756), vector control stall monitoring depends on
threshold p1745.
At higher speeds, the difference between flux setpoint r0083 and flux actual value r0084 is monitored.
p2179[0...n]
Output load identification current limit / Outp_ld iden I_lim
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2002
Data set: DDS, p0180
Units group: 6_2
Unit selection: p0505
Min
0.00 [Arms]
Max
1000.00 [Arms]
Description:
Sets the current limit for output load identification.
Dependency:
Refer to: p2180
Factory setting
0.00 [Arms]
Notice:
For synchronous motors the output current can be almost zero under no load conditions.
Note:
A missing output load condition exists if the motor is either not connected or a phase has failed.
p2180[0...n]
Missing output load delay time / No load t_delay
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
10000 [ms]
Description:
Sets the delay time to detect a missing output load.
Dependency:
Refer to: p2179
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
2000 [ms]
1-291
Parameters
List of Parameters
p2181[0...n]
Load monitoring response / Load monit resp
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
6
Factory setting
0
Description:
Sets the response when evaluating the load monitoring.
Value:
0:
1:
2:
3:
4:
5:
6:
Dependency:
Refer to: p2182, p2183, p2184, p2185, p2186, p2187, p2188, p2189, p2190, p2192, p2193, r2198, p3230, p3231
Load monitoring disabled
A07920 for torque/speed too low
A07921 for torque/speed too high
A07922 for torque/speed out of tolerance
F07923 for torque/speed too low
F07924 for torque/speed too high
F07925 for torque/speed out of tolerance
Refer to: A07920, A07921, A07922, F07923, F07924, F07925
Note:
The response to the faults F07923 ... F07925 can be set. F07926 is evaluated only if p2181 is not zero.
This parameter setting has no effect on the production of fault F07936.
p2182[0...n]
Description:
Load monitoring speed threshold value 1 / n_thresh 1
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
150.00 [rpm]
Sets the speed/torque envelope curve for load monitoring.
The envelope curve (upper and lower envelope curve) is defined as follows based on 3 speed thresholds:
p2182 (n_threshold 1) --> p2185 (M_threshold 1, upper), p2186 (M_threshold 1, lower)
p2183 (n_threshold 2) --> p2187 (M_threshold 2, upper), p2188 (M_threshold 2, lower)
p2184 (n_threshold 3) --> p2189 (M_threshold 3, upper), p2190 (M_threshold 3, lower)
Dependency:
The following applies: p2182 < p2183 < p2184
Refer to: p2183, p2184, p2185, p2186
p2183[0...n]
Description:
Load monitoring speed threshold value 2 / n_thresh 2
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
900.00 [rpm]
Sets the speed/torque envelope curve for load monitoring.
The envelope curve (upper and lower envelope curve) is defined as follows based on 3 speed thresholds:
p2182 (n_threshold 1) --> p2185 (M_threshold 1, upper), p2186 (M_threshold 1, lower)
p2183 (n_threshold 2) --> p2187 (M_threshold 2, upper), p2188 (M_threshold 2, lower)
p2184 (n_threshold 3) --> p2189 (M_threshold 3, upper), p2190 (M_threshold 3, lower)
Dependency:
The following applies: p2182 < p2183 < p2184
Refer to: p2182, p2184, p2187, p2188
1-292
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2184[0...n]
Description:
Load monitoring speed threshold value 3 / n_thresh 3
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Factory setting
1500.00 [rpm]
Sets the speed/torque envelope curve for load monitoring.
The envelope curve (upper and lower envelope curve) is defined as follows based on 3 speed thresholds:
p2182 (n_threshold 1) --> p2185 (M_threshold 1, upper), p2186 (M_threshold 1, lower)
p2183 (n_threshold 2) --> p2187 (M_threshold 2, upper), p2188 (M_threshold 2, lower)
p2184 (n_threshold 3) --> p2189 (M_threshold 3, upper), p2190 (M_threshold 3, lower)
Dependency:
The following applies: p2182 < p2183 < p2184
Refer to: p2182, p2183, p2189, p2190
p2185[0...n]
Load monitoring torque threshold 1, upper / M_thresh 1 upper
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Description:
Sets the speed/torque envelope curve for load monitoring.
Dependency:
The following applies: p2185 > p2186
Factory setting
10000000.00 [Nm]
Refer to: p2182, p2186
Note:
The upper envelope curve is defined by p2185, p2187 and p2189.
p2186[0...n]
Load monitoring torque threshold 1, lower / M_thresh 1 lower
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Description:
Sets the speed/torque envelope curve for load monitoring.
Dependency:
The following applies: p2186 < p2185
Factory setting
0.00 [Nm]
Refer to: p2182, p2185
Note:
The lower envelope curve is defined by p2186, p2188 and p2190.
p2187[0...n]
Load monitoring torque threshold 2, upper / M_thresh 2 upper
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Description:
Sets the speed/torque envelope curve for load monitoring.
Dependency:
The following applies: p2187 > p2188
Factory setting
10000000.00 [Nm]
Refer to: p2183, p2188
Note:
The upper envelope curve is defined by p2185, p2187 and p2189.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-293
Parameters
List of Parameters
p2188[0...n]
Load monitoring torque threshold 2, lower / M_thresh 2 lower
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Description:
Sets the speed/torque envelope curve for load monitoring.
Dependency:
The following applies: p2188 < p2187
Factory setting
0.00 [Nm]
Refer to: p2183, p2187
Note:
The lower envelope curve is defined by p2186, p2188 and p2190.
p2189[0...n]
Load monitoring torque threshold 3, upper / M_thresh 3 upper
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Description:
Sets the speed/torque envelope curve for load monitoring.
Dependency:
The following applies: p2189 > p2190
Factory setting
10000000.00 [Nm]
Refer to: p2184, p2190
Note:
The upper envelope curve is defined by p2185, p2187 and p2189.
p2190[0...n]
Load monitoring torque threshold 3, lower / M_thresh 3 lower
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 7_1
Unit selection: p0505
Min
0.00 [Nm]
Max
20000000.00 [Nm]
Description:
Sets the speed/torque envelope curve for load monitoring.
Dependency:
The following applies: p2190 < p2189
Factory setting
0.00 [Nm]
Refer to: p2184, p2189
Note:
The lower envelope curve is defined by p2186, p2188 and p2190.
p2192[0...n]
Load monitoring delay time / Load monit t_del
Description:
1-294
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [s]
Max
65.00 [s]
Factory setting
10.00 [s]
Sets the delay time to evaluate the load monitoring.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2193[0...n]
Load monitoring configuration / Load monit config
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
1
Description:
Sets the load monitoring configuration.
Value:
0:
1:
2:
3:
Dependency:
Refer to: p2182, p2183, p2184, p2185, p2186, p2187, p2188, p2189, p2190, p2192, r2198, p3230, p3231, p3232
Monitoring switched out
Monitoring torque and load drop
Monitoring speed and load drop
Monitoring load drop
Refer to: A07920, A07921, A07922, F07923, F07924, F07925, F07936
p2194[0...n]
Description:
Torque threshold value 2 / M_thresh val 2
Access level: 3
Calculated: p0340 = 1,3,5
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [%]
Max
100.00 [%]
Factory setting
90.00 [%]
Sets the torque threshold value for the message "Torque utilization < torque threshold value 2" (BO: r2199.11).
The message "torque setpoint < p2174" (BO: r2198.10) and "torque utilization < p2194" (BO: r2199.11) are only
evaluated after the run-up and the delay time has expired.
Dependency:
Refer to: r0033, p2195, r2199
p2195[0...n]
Torque utilization switch-off delay / M_util t_off
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [ms]
Max
1000.0 [ms]
Factory setting
800.0 [ms]
Sets the switch-off delay time for the negated signal "run-up completed".
The message "torque setpoint < p2174" (BO: r2198.10) and "torque utilization < p2194" (BO: r2199.11) are only
evaluated after the run-up and the delay time has expired.
Dependency:
Refer to: p2174, p2194
p2196[0...n]
Torque utilization scaling / M_util scal
Description:
Access level: 1
Calculated: -
Data type: FloatingPoint32
Can be changed: C(1, 3), U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [%]
Max
1000.00 [%]
Factory setting
100.00 [%]
Sets the scaling factor for torque utilization (r0033).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-295
Parameters
List of Parameters
r2197.0...13
CO/BO: Status word monitoring 1 / ZSW monitor 1
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the first status word for monitoring functions.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
Notice:
Signal name
|n_act| <= n_min p1080
1 signal
Yes
0 signal
No
n_act >= 0
|n_act| >= n_set
|n_act| <= n_standstill p1226
|n_act| > n_max
Speed setp - act val deviation in tolerance
t_off
I_act >= I_threshold value p2170
Vdc_act <= Vdc_threshold value p2172
Vdc_act > Vdc_threshold value p2172
Output load is not present
|n_act| > n_max (delayed)
|n_act| > n_max error
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
FP
8020
8011
8020
8020
8010
8011
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
8020
8020
8020
8020
8021
-
Re bit 06:
When the overspeed is reached, this bit is set and F07901 output immediately following this. The bit is canceled
again as soon as the next pulse inhibit is present.
Note:
Re bit 00:
The threshold value is set in p1080 and the hysteresis in p2150.
Re bit 01, 02:
The threshold value is set in p2155 and the hysteresis in p2140.
Re bit 03:
1 signal direction of rotation positive.
0 signal: direction of rotation negative.
The hysteresis is set in p2150.
Re bit 04:
The threshold value is set in r1119 and the hysteresis in p2150.
Re bit 05:
The threshold value is set in p1266 and the delay time in p1228.
Re bit 06:
The hysteresis is set in p2162.
Re bit 07:
The threshold value is set in p2163 and the hysteresis is set in p2164.
Re bit 08:
The threshold value is set in p2170 and the delay time in p2171.
Re bit 09, 10:
The threshold value is set in p2172 and the delay time in p2173.
Re bit 11:
The threshold value is set in p2179 and the delay time in p2180.
Re bit 12:
The threshold value is set in p2182, the hysteresis in p2162, and the delay time (for canceling the signal) in p2152.
1-296
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2198.0...13
CO/BO: Status word monitoring 2 / ZSW monitor 2
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the second status word for monitoring functions.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
09
10
11
12
13
Note:
Signal name
|n_act| <= speed threshold value 5
|n_act| > speed threshold value 5
|n_act| <= speed threshold value 6
|n_act| > speed threshold value 6
|n_set| < p2161
n_set > 0
Motor blocked
Motor stalled
|I_act| < I_threshold value p2170
|M_act| > torque threshold value 1 and
n_set reached
|M_set| < torque threshold value 1
Load monitoring signals an alarm
Load monitoring signals a fault condition
|M_act| > torque threshold value 1
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
FP
8021
8021
8021
8021
8011
8011
8012
8012
8020
8021
Yes
Yes
Yes
Yes
No
No
No
No
8012
8013
8013
8021
Re bit 10:
The torque threshold value 1 is set in p2174.
Re bit 12:
This bit is reset after the fault cause disappears, even if the fault itself is still present.
r2199.0...11
CO/BO: Status word monitoring 3 / ZSW monitor 3
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the third status word for monitoring functions.
Bit field:
Bit
00
01
04
05
11
Note:
Signal name
|n_act| < speed threshold value 3
f or n comparison value reached or
exceeded
Speed setp - act val deviation in tolerance
t_on
Ramp-up/ramp-down completed
Torque utilization < torque threshold value 2
1 signal
Yes
Yes
0 signal
No
No
FP
8010
8010
Yes
No
8011
Yes
Yes
No
No
8011
8012
Re bit 00:
The speed threshold value 3 is set in p2161.
Re bit 01:
The comparison value is set in p2141. We recommend setting the hysteresis (p2142) for canceling the bit to a value
lower than that in p2141. Otherwise, the bit will never be reset.
Re bit 11:
The torque threshold value 2 is set in p2194.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-297
Parameters
List of Parameters
p2200[0...n]
Description:
BI: Technology controller enable / Tec_ctrl enable
Access level: 2
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source to switch in/switch out the technology controller.
The technology controller is switched in with a 1 signal.
p2201[0...n]
CO: Technology controller, fixed value 1 / Tec_ctr fix val 1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
10.00 [%]
Description:
Sets the value for fixed value 1 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2202[0...n]
CO: Technology controller, fixed value 2 / Tec_ctr fix val 2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
20.00 [%]
Description:
Sets the value for fixed value 2 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2203[0...n]
CO: Technology controller, fixed value 3 / Tec_ctr fix val 3
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
30.00 [%]
Description:
Sets the value for fixed value 3 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2204[0...n]
CO: Technology controller, fixed value 4 / Tec_ctr fix val 4
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
40.00 [%]
Description:
Sets the value for fixed value 4 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
1-298
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2205[0...n]
CO: Technology controller, fixed value 5 / Tec_ctr fix val 5
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
50.00 [%]
Description:
Sets the value for fixed value 5 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2206[0...n]
CO: Technology controller, fixed value 6 / Tec_ctr fix val 6
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
60.00 [%]
Description:
Sets the value for fixed value 6 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2207[0...n]
CO: Technology controller, fixed value 7 / Tec_ctr fix val 7
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
70.00 [%]
Description:
Sets the value for fixed value 7 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2208[0...n]
CO: Technology controller, fixed value 8 / Tec_ctr fix val 8
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
80.00 [%]
Description:
Sets the value for fixed value 8 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2209[0...n]
CO: Technology controller, fixed value 9 / Tec_ctr fix val 9
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
90.00 [%]
Description:
Sets the value for fixed value 9 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-299
Parameters
List of Parameters
p2210[0...n]
CO: Technology controller, fixed value 10 / Tec_ctr fix val 10
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
100.00 [%]
Description:
Sets the value for fixed value 10 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2211[0...n]
CO: Technology controller, fixed value 11 / Tec_ctr fix val 11
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
110.00 [%]
Description:
Sets the value for fixed value 11 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2212[0...n]
CO: Technology controller, fixed value 12 / Tec_ctr fix val 12
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
120.00 [%]
Description:
Sets the value for fixed value 12 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2213[0...n]
CO: Technology controller, fixed value 13 / Tec_ctr fix val 13
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
130.00 [%]
Description:
Sets the value for fixed value 13 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2214[0...n]
CO: Technology controller, fixed value 14 / Tec_ctr fix val 14
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
140.00 [%]
Description:
Sets the value for fixed value 14 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
1-300
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2215[0...n]
CO: Technology controller, fixed value 15 / Tec_ctr fix val 15
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
150.00 [%]
Description:
Sets the value for fixed value 15 of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222, p2223, r2224, r2229
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
p2216[0...n]
Technology controller fixed value selection method / Tec_ctr FixVal sel
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
1
Max
2
Factory setting
1
Description:
Selects the method that can be used to select the fixed setpoints.
Value:
1:
2:
p2220[0...n]
BI: Technology controller fixed value selection bit 0 / Tec_ctrl sel bit 0
Fixed value selection direct
Fixed value selection binary
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the fixed value of the technology controller.
Dependency:
Refer to: p2221, p2222, p2223
p2221[0...n]
BI: Technology controller fixed value selection bit 1 / Tec_ctrl sel bit 1
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the fixed value of the technology controller.
Dependency:
Refer to: p2220, p2222, p2223
p2222[0...n]
BI: Technology controller fixed value selection bit 2 / Tec_ctrl sel bit 2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source to select the fixed value of the technology controller.
Dependency:
Refer to: p2220, p2221, p2223
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
0
1-301
Parameters
List of Parameters
p2223[0...n]
BI: Technology controller fixed value selection bit 3 / Tec_ctrl sel bit 3
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source to select the fixed value of the technology controller.
Dependency:
Refer to: p2220, p2221, p2222
r2224
CO: Technology controller, fixed value effective / Tec_ctr FixVal eff
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the selected and effective fixed value of the technology controller.
Dependency:
Refer to: r2229
r2225.0
CO/BO: Technology controller fixed value selection status word / Tec_ctr FixVal ZSW
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status word for the fixed value selection of the technology controller.
Bit field:
Bit
00
r2229
Technology controller number actual / Tec_ctrl No. act
Signal name
Technology controller fixed value selected
1 signal
Yes
0 signal
No
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the number of the selected fixed setpoint of the technology controller.
Dependency:
Refer to: r2224
1-302
FP
7950,
7951
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2230[0...n]
Technology controller motorized potentiometer configuration / Tec_ctr mop config
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0000 0100 bin
Description:
Sets the configuration for the motorized potentiometer of the technology controller.
Bit field:
Bit
00
02
03
04
Signal name
Data save active
Initial rounding-off active
Non-volatile data save active for p2230.0 =
1
Ramp-function generator always active
Dependency:
Refer to: r2231, p2240
Notice:
For p0014 = 1, the following applies:
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
-
Yes
No
-
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
Re bit 00:
0: The setpoint for the motorized potentiometer is not saved and after ON is entered using p2240.
1: The setpoint for the motorized potentiometer is saved and after ON is entered using r2231. In order to save in a
non-volatile fashion, bit 03 should be set to 1.
Re bit 02:
0: Without initial rounding-off
1: With initial rounding-off.
The selected ramp-up/down time is correspondingly exceeded. The initial rounding-off is a sensitive way of specifying small changes (progressive reaction when keys are pressed). The jerk for initial rounding is independent of the
ramp-up time and only depends on the selected maximum value (p2237).
It is calculated as follows:
r = 0.0001 x max(p2237, |p2238| ) [%] / 0.13^2 [s^2]
The jerk is effective until the maximum acceleration is reached (a_max = p2237 [%] / p2247 [s] or a_max = p2238
[%] / p2248 [s]), after which the drive continues to run linearly with constant acceleration. The higher the maximum
acceleration (the lower that p2247 is), the longer the ramp-up time increases with respect to the set ramp-up time.
Re bit 03:
0: Non-volatile data save de-activated.
1. The setpoint for the motorized potentiometer is saved in a non-volatile fashion (for p2230.0 = 1).
Re bit 04:
When the bit is set, the ramp-function generator is computed independent of the pulse enable. The actual output
value of the motorized potentiometer is always in r2250.
r2231
Description:
Technology controller motorized potentiometer setpoint memory / Tec_ctrl mop mem
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the setpoint memory for the motorized potentiometer of the technology controller.
For p2230.0 = 1, the last setpoint that was saved is entered after ON.
Dependency:
Refer to: p2230
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-303
Parameters
List of Parameters
p2235[0...n]
Description:
BI: Technology controller motorized potentiometer raise setpoint / Tec_ctrl mop raise
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source to continually increase the setpoint for the motorized potentiometer of the technology controller.
The setpoint change (CO: r2250) depends on the set ramp-up time (p2247) and the duration of the signal that is
present (BI: p2235).
Dependency:
Refer to: p2236
p2236[0...n]
BI: Technology controller motorized potentiometer lower setpoint /
Tec_ctrl mop lower
Description:
Dependency:
p2237[0...n]
Description:
Dependency:
p2238[0...n]
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source to continually reduce the setpoint for the motorized potentiometer of the technology controller.
The setpoint change (CO: r2250) depends on the set ramp-down time (p2248) and the duration of the signal that is
present (BI: p2236).
Refer to: p2235
Technology controller motorized potentiometer maximum value / Tec_ctrl mop max
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
100.00 [%]
Sets the maximum value for the motorized potentiometer of the technology controller.
Refer to: p2238
Technology controller motorized potentiometer minimum value / Tec_ctrl mop min
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
-100.00 [%]
Description:
Dependency:
Sets the minimum value for the motorized potentiometer of the technology controller.
Refer to: p2237
p2240[0...n]
Technology controller motorized potentiometer starting value / Tec_ctrl mop start
Description:
Dependency:
1-304
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
0.00 [%]
Sets the starting value for the motorized potentiometer of the technology controller.
For p2230.0 = 0, this setpoint is entered after ON.
Refer to: p2230
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2245
CO: Technology controller mot. potentiometer setpoint before RFG /
Tec_ctr mop befRFG
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Sets the effective setpoint in front of the internal motorized potentiometer ramp-function generator of the technology
controller.
Dependency:
Refer to: r2250
p2247[0...n]
Technology controller motorized potentiometer ramp-up time / Tec_ctr mop t_r-up
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [s]
Max
1000.0 [s]
Factory setting
10.0 [s]
Description:
Sets the ramp-up time for the internal ramp-function generator for the motorized potentiometer of the technology
controller.
Dependency:
Refer to: p2248
Note:
The time is referred to 100 %.
When the initial rounding-off is activated (p2230.2 = 1) the ramp-up is correspondingly extended.
p2248[0...n]
Technology controller motorized potentiometer ramp-down time /
Tec_ctrMop t_rdown
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.0 [s]
Max
1000.0 [s]
Factory setting
10.0 [s]
Description:
Sets the ramp-down time for the internal ramp-function generator for the motorized potentiometer of the technology
controller.
Dependency:
Refer to: p2247
Note:
The time is referred to 100 %.
When the initial rounding-off is activated (p2230.2 = 1) the ramp-down is correspondingly extended.
r2250
CO: Technology controller motorized potentiometer setpoint after RFG /
Tec_ctr mop aftRFG
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the effective setpoint after the internal ramp-function generator for the motorized potentiometer of the
technology controller.
Dependency:
Refer to: r2245
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-305
Parameters
List of Parameters
p2251
Technology controller mode / Tec_ctrl mode
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Sets the mode for using the technology controller output.
Value:
0:
1:
Dependency:
p2251 = 0, 1 is only effective if the enable signal of the technology controller is interconnected (p2200 > 0).
p2253[0...n]
CI: Technology controller setpoint 1 / Tec_ctrl setp 1
Technology controller as main speed setpoint
Technology controller as supplementary speed setpoint
Access level: 2
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the setpoint 1 of the technology controller.
Dependency:
Refer to: p2254, p2255
p2254[0...n]
Factory setting
0
CI: Technology controller setpoint 2 / Tec_ctrl setp 2
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the setpoint 2 of the technology controller.
Dependency:
Refer to: p2253, p2256
p2255
Technology controller setpoint 1 scaling / Tec_ctrl set1 scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [%]
Max
100.00 [%]
Factory setting
100.00 [%]
Description:
Sets the scaling for the setpoint 1 of the technology controller.
Dependency:
Refer to: p2253
p2256
Technology controller setpoint 2 scaling / Tec_ctrl set2 scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [%]
Max
100.00 [%]
Description:
Sets the scaling for the setpoint 2 of the technology controller.
Dependency:
Refer to: p2254
1-306
Factory setting
100.00 [%]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2257
Technology controller, ramp-up time / Tec_ctrl t_ramp-up
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [s]
Max
650.00 [s]
Factory setting
1.00 [s]
Description:
Sets the ramp-up time of the technology controller.
Dependency:
Refer to: p2258
Note:
The ramp-up time is referred to 100 %.
p2258
Technology controller ramp-down time / Tec_ctrl t_ramp-dn
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [s]
Max
650.00 [s]
Factory setting
1.00 [s]
Description:
Sets the ramp-down time of the technology controller.
Dependency:
Refer to: p2257
Note:
The ramp-down time is referred to 100 %.
r2260
CO: Technology controller setpoint after ramp-function generator /
Tec_ctr set aftRFG
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Sets the setpoint after the ramp-function generator of the technology controller.
p2261
Technology controller setpoint filter time constant / Tec_ctrl set T
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [s]
Max
60.000 [s]
Factory setting
0.000 [s]
Description:
Sets the time constant for the setpoint filter (PT1) of the technology controller.
r2262
CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
Description:
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the smoothed setpoint after the setpoint filter (PT1) of the technology controller.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-307
Parameters
List of Parameters
p2263
Technology controller type / Tec_ctrl type
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Sets the technology controller type.
Value:
0:
1:
p2264[0...n]
Factory setting
0
D component in the actual value signal
D component in the fault signal
CI: Technology controller actual value / Tec_ctrl act val
Access level: 2
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the actual value of the technology controller.
p2265
Technology controller actual value filter time constant / Tec_ctrl act T
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [s]
Max
60.000 [s]
Factory setting
0.000 [s]
Description:
Sets the time constant for the actual value filter (PT1) of the technology controller.
r2266
CO: Technology controller actual value after filter / Tec_ctr act aftFlt
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the smoothed actual value after the filter (PT1) of the technology controller
p2267
Technology controller upper limit actual value / Tec_ctrl u_lim act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Description:
Sets the upper limit for the actual value signal of the technology controller.
Dependency:
Refer to: p2264, p2265, p2271
Factory setting
100.00 [%]
Refer to: F07426
Notice:
1-308
If the actual value exceeds this upper limit, this results in fault F07426.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2268
Description:
Dependency:
Technology controller lower limit actual value / Tec_ctrl l_lim act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
-100.00 [%]
Notice:
Sets the lower limit for the actual value signal of the technology controller.
Refer to: p2264, p2265, p2271
Refer to: F07426
If the actual value falls below this lower limit, this results in fault F07426.
p2269
Technology controller gain actual value / Tech_ctrl gain act
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [%]
Max
500.00 [%]
Factory setting
100.00 [%]
Description:
Dependency:
Note:
Scaling factor for the actual value of the technology controller.
Refer to: p2264, p2265, p2267, p2268, p2271
For 100%, the actual value is not changed.
p2270
Technology controller actual value function / Tec_ctr ActVal fct
Description:
Value:
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Dependency:
Setting to use an arithmetic function for the actual value signal of the technology controller.
0:
No function
1:
Root function (root from x)
2:
Square function (x * x)
3:
Cube function (x * x * x)
Refer to: p2264, p2265, p2267, p2268, p2269, p2271
p2271
Technology controller actual value inversion (sensor type) / Tech_ctrl act inv
Description:
Value:
Caution:
Note:
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Setting to invert the actual value signal of the technology controller.
The inversion depends on the sensor type for the actual value signal.
0:
No inversion
1:
Inversion actual value signal
If the actual value inversion is incorrectly selected, then the closed-loop control with the technology controller can
become unstable and can oscillate!
The correct setting can be determined as follows:
- inhibit the technology controller (p2200 = 0).
- increase the motor speed and in so doing, measure the actual value signal of the technology controller.
--> If the actual value increases as the motor speed increases, then p2271 should be set to 0 (no inversion).
--> If the actual value decreases as the motor speed increases, then p2271 should be set to 1 (the actual value signal is inverted).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-309
Parameters
List of Parameters
r2272
CO: Technology controller actual value scaled / Tech_ctrl act scal
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Description:
Dependency:
Displays the scaled actual value signal of the technology controller.
Refer to: p2264, p2265, r2266, p2267, p2268, p2269, p2270, p2271
r2273
CO: Technology controller error / Tec_ctrl error
Factory setting
- [%]
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: 9_1
Unit selection: p0595
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Dependency:
Displays the error (system deviation) between the setpoint and actual value of the technology controller.
Refer to: p2263
p2274
Technology controller differentiation, time constant / Tec_ctrl D comp T
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [s]
Max
60.000 [s]
Factory setting
0.000 [s]
Description:
Note:
Sets the time constant for the differentiation (D component) of the technology controller.
p2274 = 0: Differentiation is disabled.
p2280
Technology controller proportional gain / Tec_ctrl Kp
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000
Max
1000.000
Description:
Note:
Sets the proportional gain (P component) of the technology controller.
p2280 = 0: The proportional gain is disabled.
p2285
Technology controller integral time / Tec_ctrl Tn
Description:
Notice:
Note:
1-310
Factory setting
1.000
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [s]
Max
10000.000 [s]
Factory setting
30.000 [s]
Sets the integral time (I component, integrating time constant) of the technology controller.
The following applies for p2251 = 0:
If the output of the technology controller lies within the range of a suppression (skip) bandwidth (p1091 ... p1094,
p1101) or below the minimum speed (p1080), the integral component of the controller is held so that the controller
temporarily works as a P controller. This is necessary in order to prevent the controller from behaving in an unstable
manner, as the ramp-function generator switches to the parameterized up and down ramps (p1120, p1121) at the
same time in order to avoid setpoint steps. This state can be exited or avoided by changing the controller setpoint or
by using the start speed (= minimum speed).
When the controller output reaches the limit, the I component of the controller is held.
p2285 = 0:
The integral time is disabled and the I component of the controller is reset.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2286[0...n]
BI: Hold technology controller integrator / Tec_ctr integ stop
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
56.13
Description:
Sets the signal source to hold the integrator for the technology controller.
p2289[0...n]
CI: Technology controller pre-control signal / Tec_ctrl prectrl
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the pre-control signal of the technology controller.
p2291
CO: Technology controller maximum limiting / Tec_ctrl max_limit
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
100.00 [%]
Description:
Sets the maximum limit of the technology controller.
Dependency:
Refer to: p2292
Caution:
The maximum limit must always be greater than the minimum limit (p2291 > p2292).
p2292
CO: Technology controller minimum limiting / Tec_ctrl min_lim
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-200.00 [%]
Max
200.00 [%]
Factory setting
0.00 [%]
Description:
Sets the minimum limit of the technology controller.
Dependency:
Refer to: p2291
Caution:
The maximum limit must always be greater than the minimum limit (p2291 > p2292).
p2293
Technology controller ramp-up/ramp-down time / Tec_ctr ramp up/dn
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [s]
Max
100.00 [s]
Description:
Sets the ramping time for the output signal of the technology controller.
Dependency:
Refer to: p2291, p2292
Note:
The time refers to the set maximum and minimum limits (p2291, p2292).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
1.00 [s]
1-311
Parameters
List of Parameters
r2294
CO: Technology controller output signal / Tec_ctrl outp_sig
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the output signal of the technology controller.
Dependency:
Refer to: p2295
p2295
CO: Technology controller output scaling / Tec_ctrl outp scal
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-100.00 [%]
Max
100.00 [%]
Factory setting
100.00 [%]
Description:
Sets the scaling for the output signal of the technology controller.
p2296[0...n]
CI: Technology controller output scaling / Tec_ctrl outp scal
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
2295[0]
Description:
Sets the signal source for the scaling value of the technology controller.
Dependency:
Refer to: p2295
p2297[0...n]
CI: Technology controller maximum limit signal source / Tec_ctrl m_lm s_sc
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1084[0]
Description:
Sets the signal source for the maximum limiting of the technology controller.
Dependency:
Refer to: p2291
Note:
In order that the output of the technology controller does not exceed the maximum speed limit, its upper limit p2297
should be connected to the actual maximum speed r1084.
In mode p2251 = 1, p2299 must also be connected to the output of the ramp-function generator r1150.
p2298[0...n]
CI: Technology controller minimum limit signal source / Tec_ctrl min_l s_s
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1087[0]
Description:
Sets the signal source for the minimum limiting of the technology controller.
Dependency:
Refer to: p2292
Note:
If the technology controller is rotated in a negative direction in mode p2251 = 0, its lower limit p2298 should be connected to the actual minimum speed r1087.
In mode p2251 = 1, p2299 must also be connected to the output of the ramp-function generator r1150.
1-312
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p2299[0...n]
CI: Technology controller limit offset / Tech_ctrl lim offs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the offset of the output limiting of the technology controller.
Note:
In mode p2251 = 1, p2299 must be connected to the output of ramp-function generator r1150 so that the technology controller stops when the speed limits are reached (see also p2297, p2298).
p2302
Technology controller output signal starting value / Tec_ctr start val
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [%]
Max
200.00 [%]
Factory setting
0.00 [%]
Sets the start value for the output of the technology controller.
When the technology controller is enabled (refer to p2200 and r0056.3) then its output signal (r2294) starts to run
from this starting value.
Dependency:
The starting value is only effective in the mode "technology controller as main speed setpoint" (p2251 = 0).
Note:
If the technology controller operates on the speed/setpoint channel (p2251 = 0), then the starting value is interpreted as the starting speed and when operation is enabled, is connected to the output of the technology controller
(r2294).
If fault F07426 "technology controller actual value limited" occurs while ramping up to the starting value and if the
associated reaction has been set to "NONE" (see p2100, p2101), the starting value is kept as the speed setpoint
instead of a switch to closed-loop control operation.
p2306
Description:
Technology controller fault signal inversion / Tec_ctrl fault inv
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Setting to invert the fault signal of the technology controller.
The setting depends on the type of control loop.
Value:
0:
1:
No inversion
Inversion
Caution:
If the actual value inversion is incorrectly selected, then the closed-loop control with the technology controller can
become unstable and can oscillate!
Note:
The correct setting can be determined as follows:
- inhibit the technology controller (p2200 = 0).
- increase the motor speed and in so doing, measure the actual value signal (of the technology controller).
- if the actual value increases with increasing motor speed, then the inversion should be switched out.
- if the actual value decreases with increasing motor speed, then the inversion should be set.
If value = 0:
The drive reduces the output speed when the actual value rises (e.g. for heating fans, intake pump, compressor).
If value = 1:
The drive increases the output speed when the actual value increases (e.g. for cooling fans, discharge pumps).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-313
Parameters
List of Parameters
r2344
CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Description:
Displays the smoothed speed setpoint of the technology controller prior to switching to operation with fault response
(see p2345).
Dependency:
Refer to: p2345
Note:
The smoothing time is 10 s.
p2345
Technology controller fault response / Tech_ctrl flt resp
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
2
Factory setting
0
Description:
Sets the response of the technology controller to the occurrence of a fault F07426 (technology controller actual
value limited). The fault response is executed if status bits 8 or 9 in technology controller status word r2349 are set.
If both status bits are zero, a switch back to technology controller operation will follow.
Value:
0:
1:
2:
Dependency:
The parameterized fault response is only effective if the technology controller mode is set to p2251 = 0 (technology
controller as main setpoint).
Function inhibited
On fault: Changeover to r2344 (or p2302)
On fault: Changeover to p2215
Refer to: p2267, p2268, r2344
Refer to: F07426
Notice:
Dependent upon the application, the changing over of the setpoint when fault F07426 occurs can lead to the fault
condition disappearing and the re-activation of the technology controller. This can repeat itself and cause limit oscillations. In this case a suitable fault response or a different fixed setpoint 15 for the fault response p2345 = 2 should
be selected.
Note:
The parameterized fault response can only be achieved if the default fault response of the technology controller
fault F07426 is set to "NONE" (see p2100, p2101). If a fault response other than "NONE" is entered in p2101 for
F07426, p2345 must be set to zero.
If the fault occurs during ramping up to the starting setpoint p2302, this starting setpoint is retained as the final value
(there is no changeover to the fault response setpoint).
1-314
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r2349.0...12
CO/BO: Technology controller status word / Tec_ctrl status
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status word of the technology controller.
Bit field:
Bit
00
01
02
03
04
05
06
08
09
10
11
12
p2900[0...n]
Signal name
Technology controller de-activated
Technology controller limited
Technology controller, motorized potentiometer limited max.
Technology controller, motorized potentiometer limited min.
Technology controller speed setpoint total in
setpoint channel
Technology controller RFG bypassed in the
setpoint channel
Technology controller starting value at the
current limit
Technology controller actual value at the
minimum
Technology controller actual value at the
maximum
Technology controller output at the minimum
Technology controller output at the maximum
Fault response active
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
-
Yes
No
-
Yes
No
-
Yes
No
-
No
Yes
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
CO: Fixed value 1 [%] / Fixed value 1 [%]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-10000.00 [%]
Max
10000.00 [%]
Description:
Sets a fixed percentage.
Dependency:
Refer to: p2901, p2930
Factory setting
0.00 [%]
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
The value can be used to interconnect a scaling function (e.g. scaling of the main setpoint)
p2901[0...n]
CO: Fixed value 2 [%] / Fixed value 2 [%]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-10000.00 [%]
Max
10000.00 [%]
Description:
Sets a fixed percentage.
Dependency:
Refer to: p2900, p2930
Factory setting
0.00 [%]
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
The value can be used to interconnect a scaling function (e.g. scaling of the supplementary setpoint)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-315
Parameters
List of Parameters
r2902[0...14]
CO: Fixed values [%] / Fixed values [%]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Description:
Signal sources for frequently used percentage values.
Index:
[0] = Fixed value +0 %
[1] = Fixed value +5 %
[2] = Fixed value +10 %
[3] = Fixed value +20 %
[4] = Fixed value +50 %
[5] = Fixed value +100 %
[6] = Fixed value +150 %
[7] = Fixed value +200 %
[8] = Fixed value -5 %
[9] = Fixed value -10 %
[10] = Fixed value -20 %
[11] = Fixed value -50 %
[12] = Fixed value -100 %
[13] = Fixed value -150%
[14] = Fixed value -200 %
Dependency:
Refer to: p2900, p2901, p2930
Note:
The signal sources can, for example, be used to interconnect scalings.
p2930[0...n]
Factory setting
- [%]
CO: Fixed value M [Nm] / Fixed value M [Nm]
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: p2003
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-100000.00 [Nm]
Max
100000.00 [Nm]
Description:
Sets a fixed value for torque.
Dependency:
Refer to: p2900, p2901
Factory setting
0.00 [Nm]
Notice:
A BICO interconnection to a parameter that belongs to a drive data set always acts on the effective data set.
Note:
The value can, for example, be used to interconnect a supplementary torque.
p3110
External fault 3, power-up delay / Ext fault 3 t_on
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [ms]
Max
1000 [ms]
Description:
Sets the delay time for external fault 3.
Dependency:
Refer to: p2108, p3111, p3112
Factory setting
0 [ms]
Refer to: F07862
1-316
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p3111[0...n]
Description:
BI: External fault 3, enable / Ext fault 3 enab
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
1
Sets the signal source for the enable signal of external fault 3.
External fault 3 is initiated by the following AND logic operation:
- BI: p2108 negated
- BI: p3111
- BI: p3112 negated
Dependency:
Refer to: p2108, p3110, p3112
Refer to: F07862
p3112[0...n]
Description:
BI: External fault 3 enable negated / Ext flt 3 enab neg
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the negated enable signal of external fault 3.
External fault 3 is initiated by the following AND logic operation:
- BI: p2108 negated
- BI: p3111
- BI: p3112 negated
Dependency:
Refer to: p2108, p3110, p3111
Refer to: F07862
r3113.0...15
Description:
CO/BO: NAMUR message bit bar / NAMUR bit bar
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the status of NAMUR signal bit bar.
The faults or alarms are assigned to the appropriate signaling/message classes and influence a specific message
bit.
Bit field:
Bit
00
01
02
03
04
05
06
07
08
10
11
15
Signal name
Fault drive converter data electronics / software error
Line supply fault
DC link overvoltage
Fault drive converter power electronics
Drive converter overtemperature
Ground fault
Motor overload
Bus error
External safety-relevant shutdown
Error communication internal
Fault infeed
Other faults
1 signal
Yes
0 signal
No
FP
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-317
Parameters
List of Parameters
r3131
CO: Current flt value / Current flt value
Access level: 3
Calculated: -
Data type: Integer32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the fault value of the oldest active fault.
Dependency:
Refer to: r2131, r3132
r3132
CO: Actual component number / Act comp_no.
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the component number of the oldest fault that is still active.
Dependency:
Refer to: r2131, r3131
p3230[0...n]
CI: Load monitoring, speed actual value / Load monit n_act
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: p2000
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for the speed actual value of the load monitoring.
Dependency:
Refer to: r2169, p2181, p2192, p2193, p3231
Factory setting
0
Refer to: A07920, A07921, A07922, F07923, F07924, F07925
Note:
The parameter is only effective for p2193 = 2.
p3231[0...n]
Load monitoring speed deviation / Load monit n_dev
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: 3_1
Unit selection: p0505
Min
0.00 [rpm]
Max
210000.00 [rpm]
Description:
Sets the permissible speed deviation during load monitoring (for p2193 = 2).
Dependency:
Refer to: r2169, p2181, p2193, p3230
Factory setting
150.00 [rpm]
Refer to: A07920, A07921, A07922, F07923, F07924, F07925
p3232[0...n]
BI: Load monitoring failure detection / Load_moni fail_det
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source for detecting a failure.
Dependency:
Refer to: p2192, p2193
Factory setting
1
Refer to: F07936
Note:
1-318
Monitoring is triggered with a 0 signal, as soon as the time in p2192 has expired.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p3233[0...n]
Description:
Torque actual value filter, time constant / M_act_filt T
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0 [ms]
Max
1000000 [ms]
Factory setting
100 [ms]
Sets the time constant of the PT1 element to smooth the torque actual value.
The smoothed actual torque is compared with the threshold values and is only used for messages and signals.
p3235
Phase failure signal motor monitoring time / Ph_fail t_monit
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0 [ms]
Max
2000 [ms]
Factory setting
320 [ms]
Description:
Sets the monitoring time for phase failure detection of the motor.
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
For p3235 = 0 the function is deactivated.
The monitoring is automatically de-activated during the flying restart operation for a motor that is still rotating.
3-phase phase failures cannot be detected and are indicated by other messages (e.g. F07902).
p3320[0...n]
Fluid flow machine P = f(n), Y coordinate: P flow1 %, point 1 / Fluid flow mach Y1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
25.00
Description:
The power (P) for point 1 on the Y coordinate of the flow characteristic is saved in p3320. Unit: %
Dependency:
Refer to: p3321
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3321[0...n]
Fluid flow machine P = f(n), X coordinate: n flow1 %, point 1 / Fluid flow mach X1
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
0.00
Description:
The speed (n) for point 1 on the X coordinate of the flow characteristic is saved in p3321. Unit: %
Dependency:
Refer to: p3320
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-319
Parameters
List of Parameters
p3322[0...n]
Fluid flow machine P = f(n), Y coordinate: P flow2 %, point 2 / Fluid flow mach Y2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
50.00
Description:
The power (P) for point 2 on the Y coordinate of the flow characteristic is saved in p3322. Unit: %
Dependency:
Refer to: p3323
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3323[0...n]
Fluid flow machine P = f(n), X coordinate: n flow2 %, point 2 / Fluid flow mach X2
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
25.00
Description:
The speed (n) for point 2 on the X coordinate of the flow characteristic is saved in p3323. Unit: %
Dependency:
Refer to: p3322
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3324[0...n]
Fluid flow machine P = f(n), Y coordinate: P flow3 %, point 3 / Fluid flow mach Y3
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
77.00
Description:
The power (P) for point 3 on the Y coordinate of the flow characteristic is saved in p3324. Unit: %
Dependency:
Refer to: p3325
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3325[0...n]
Fluid flow machine P = f(n), X coordinate: n flow3 %, point 3 / Fluid flow mach X3
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
50.00
Description:
The speed (n) for point 3 on the X coordinate of the flow characteristic is saved in p3325. Unit: %
Dependency:
Refer to: p3324
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
1-320
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p3326[0...n]
Fluid flow machine P = f(n), Y coordinate: P flow4 %, point 4 / Fluid flow mach Y4
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
92.00
Description:
The power (P) for point 4 on the Y coordinate of the flow characteristic is saved in p3326. Unit: %
Dependency:
Refer to: p3327
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3327[0...n]
Fluid flow machine P = f(n), X coordinate: n flow4 %, point 4 / Fluid flow mach X4
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
75.00
Description:
The speed (n) for point 4 on the X coordinate of the flow characteristic is saved in p3327. Unit: %
Dependency:
Refer to: p3326
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3328[0...n]
Fluid flow machine P = f(n), Y coordinate: P flow5 %, point 5 / Fluid flow mach Y5
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
100.00
Description:
The power (P) for point 5 on the Y coordinate of the flow characteristic is saved in p3328. Unit: %
Dependency:
Refer to: p3329
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
p3329[0...n]
Fluid flow machine P = f(n), X coordinate: n flow5 %, point 5 / Fluid flow mach X5
Access level: 2
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00
Max
100.00
Factory setting
100.00
Description:
The speed (n) for point 5 on the X coordinate of the flow characteristic is saved in p3329. Unit: %
Dependency:
Refer to: p3328
Note:
The reference value for power and speed is the rated power/rated speed.
The energy saved is displayed in r0041.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-321
Parameters
List of Parameters
p3330[0...n]
Description:
p3331[0...n]
BI: 2-3-WIRE Control Command 1 / 2-3-WIRE CC_1
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
The function of the 2-3-WIRE Control Command 1 depends on the selected 2-3-WIRE type. It shall be predefined
by p0015
BI: 2-3-WIRE Control Command 2 / 2-3-WIRE CC_2
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
The function of the 2-3-WIRE Control Command 2 depends on the selected 2-3-WIRE type. It shall be predefined
by p0015
p3332[0...n]
BI: 2-3-WIRE Control Command 3 / 2-3-WIRE CC_3
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: U, T
Scaling: -
Data set: CDS, p0170
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
The function of the 2-3-WIRE Control Command 3 depends on the selected 2-3-WIRE type. It shall be predefined
by p0015
r3333.0...3
CO/BO: 2-3-WIRE Output / 2-3-WIRE OUT
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
The output values of the 2-3-WIRE Control Command depends on the selected 2-3-WIRE type and the control
command inputs. Type shall be predefined by p0015
Bit field:
Bit
00
01
02
03
p3334
2-3-WIRE Selection / 2-3-WIRE Sel
Description:
Value:
1-322
Signal name
2-3-Wire On
2-3-Wire Reverse
2-3-Wire On/Inverse
2-3-Wire Reverse/Inverse
1 signal
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
4
FP
-
Factory setting
0
Determines the 2/3-Wire type using the terminals. It shall be predefined by p0015.
0:
No 2/3-Wire control
1:
2-Wire Forward-Backward 1
2:
2-Wire Forward-Backward 2
3:
3-Wire Enable-Forward-Backward
4:
3-Wire Enable-On-Reverse
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p3856[0...n]
Compound braking current / Compound I_brake
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: U, T
Scaling: PERCENT
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
0.00 [%]
Max
250.00 [%]
Description:
Factory setting
0.00 [%]
Compound braking current is used to define the amount of DC current that is produced on stopping the motor during U/f operation to further increase the DC brake function.
Compound braking is a superimposition of the DC brake function with regenerative braking (net braking along the
ramp) after OFF1 or OFF3. This permits braking with controlled motor frequency and minimum power input into the
motor. Effective braking without using additional hardware components is obtained by optimizing the ramp down
time and compound braking.
Dependency:
The compound braking current is only activated if the DC link voltage exceeds the threshold value in r1282.
Compound braking does not operate:
- when DC braking is active (refer to p1230, r1239)
- as long as the motor is not magnetized (e.g. for flying restart)
- for vector control (p1300 >= 20)
- for synchronous motors (p0300 = 2xx)
Caution:
Generally, increasing the braking current improves the braking effect when stopping the motor. However, if the
value is set too high, then the drive can be tripped (shut down) as a result of overcurrent or ground fault.
Recommendation: p3856 < 100 % x (r0209 - r0331) / p0305 / 2
Compound braking generates a current in the motor with a ripple manifesting the rotational frequency. The higher
the braking current is set, the higher the resulting ripple, especially when the Vdc(max) control is simultaneously
active (refer to to p1280).
Note:
The parameter value is entered relative to the rated motor current (p0305). Compound braking is deactivated with
p3856 = 0%.
r3859.0
CO/BO: Compound braking status word / Compound Br ZSW
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status word of the compound braking.
Bit field:
Bit
00
Dependency:
Refer to: p3856
Signal name
Compound braking active
Factory setting
1 signal
Yes
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
No
FP
-
1-323
Parameters
List of Parameters
p3900
Description:
Completion of quick commissioning / Compl quick_comm
Access level: 1
Calculated: -
Data type: Integer16
Can be changed: C(1)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
3
Factory setting
0
Exits quick commissioning (p0010 = 1) with automatic calculation of all parameters of all existing drive data sets
that depend on the entries made during quick commissioning.
p3900 = 1 initially includes a parameter reset (factory setting, the same as p0970 = 1) for all parameters of the drive
object; however, without overwriting the entries made during the quick commissioning.
The interconnections of PROFIBUS PZD telegram selection (p0922) and the interconnections via p15 and p1500
are re-established and all of the dependent motor, open-loop and control-loop control parameters are calculated
(corresponding to p0340 = 1).
p3900 = 2 includes the restoration of the interconnections of PROFIBUS PZD telegram selection (p0922) and the
interconnections via p15 and p1500 and the calculations corresponding to p0340 = 1.
p3900 = 3 only includes the calculations associated with the motor, open-loop and closed-loop control parameters
corresponding to p0340 = 1.
Value:
0:
1:
2:
3:
No quick parameterization
Quick parameterization after parameter reset
Quick parameterization (only) for BICO and motor parameters
Quick parameterization for motor parameters (only)
Notice:
After the value has been modified, no further parameter modifications can be made and the status is shown in
r3996. Modifications can be made again when r3996 = 0.
Note:
When the calculations have been completed, p3900 and p0010 are automatically reset to a value of 0.
When calculating motor, open-loop and closed-loop control parameters (such as for p0340 = 1) parameters associated with a selected Siemens catalog motor are not overwritten.
If a catalog motor has not been selected (see p0300), then the following parameters are reset with p3900 > 0 in
order to restore the situation that applied when commissioning the drive for the first time:
for induction motors p0320, p0352, p0362 ... p0369, p0604, p0605, p0626 ... p0628.
for synchronous motors p0326, p0327, p0352, p0604, p0605.
r3925[0...n]
Identification final display / Ident final_disp
Access level: 3
Calculated: p0340 = 1
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the commissioning steps that have been carried out.
Bit field:
Bit
00
02
03
15
Note:
Signal name
Motor/control parameters calculated (p0340
= 1, p3900 > 0)
Motor data identification carried out at
standstill (p1910 = 1)
Rotating measurement carried out (p1960 =
1, 2)
Motor equivalent circuit diagram parameters
changed
1 signal
Yes
0 signal
No
FP
-
Yes
No
-
Yes
No
-
Changed
Not changed
-
The individual bits are only set if the appropriate action has been initiated and successfully completed.
When motor rating plate parameters are changed, the final display is reset.
When setting the individual bits, all of the most significant bits are reset.
1-324
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r3926[0...n]
Alternating voltage generation base voltage amplitude / Alt U_gen U_base
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: MDS
Units group: -
Unit selection: -
Min
- [V]
Max
- [V]
Factory setting
- [V]
Description:
Displays the base voltage of the alternating voltage for the last motor data identification.
0: No alternating voltages, function de-activated.
Otherwise: Base voltage for alternating current generation in volts.
r3927[0...n]
Motor data identification control word / MotID STW
Access level: 3
Calculated: p0340 = 1
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Successfully completed component of the last motor data identification carried out.
Bit field:
Bit
00
02
03
05
06
07
11
12
14
15
Signal name
Stator inductance estimate no measurement
Rotor time constant estimate no measurement
Leakage inductance estimate no measurement
Determine Tr and Lsig evaluation in the time
range
Activate vibration damping
De-activate vibration detection
De-activate pulse measurement Lq Ld
De-activate rotor resistance Rr measurement
De-activate valve interlocking time measurement
Determine only stator resistance, valve voltage fault, dead time
Dependency:
Refer to: r3925
Note:
The parameter is a copy of p1909.
r3928[0...n]
1 signal
Yes
0 signal
No
FP
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
Yes
Yes
Yes
No
No
No
No
-
Yes
No
-
Yes
No
-
Rotating measurement configuration / Rot meas config
Access level: 3
Calculated: p0340 = 1
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Successfully completed component of the last rotating measurement carried out.
Bit field:
Bit
01
02
03
04
05
Signal name
Saturation characteristic identification
Moment of inertia identification
Re-calculates the speed controller parameters
Speed controller optimization (vibration test)
q leakage inductance ident. (for current controller adaptation)
Dependency:
Refer to: r3925
Note:
The parameter is a copy of p1959.
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
-
Yes
Yes
No
No
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-325
Parameters
List of Parameters
r3929[0...n]
Motor data identification modulated voltage generation / MotID U_gen mod
Access level: 4
Calculated: p0340 = 1
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: DDS, p0180
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Configuration of voltage generation for the various MotID sections in the case of the most recent successful MotID.
Bit field:
Bit
00
01
02
03
04
05
08
09
10
11
12
13
r3930[0...4]
Description:
Signal name
Wobble U_generate to determine dead-time
correction
Wobble U_generate to determine stator
resistance
Wobble U_generate to determine rotor time
constant
Wobble U_generate to determine leakage
inductance
Wobble U_generate to determine dyn. leakage inductance
Wobble U_generate to determine magnetizing inductance
Alternating U_generate to determine deadtime correction
Alternating U_generate to determine stator
resistance
Alternating U_generate to determine rotor
time constant
Alternating U_generate to determine leakage inductance
Alternating U_generate to determine dyn.
leakage inductance
Alternating U_generate to determine magnetizing inductance
1 signal
Yes
0 signal
No
FP
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Yes
No
-
Power unit EEPROM characteristics / PU characteristics
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the characteristics (A5E number and versions) of the power unit.
[0]: A5E number xxxx (A5Exxxxyyyy)
[1]: A5E number yyyy (A5Exxxxyyyy)
[2]: File version (logistic)
[3]: File version (fixed data)
[4]: File version (calib data)
p3950
Description:
1-326
Service parameter / Serv. par.
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: C, U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
For service personnel only.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r3960[0...1]
Control Unit temperature measured / CU temp measured
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: -
Scaling: p2006
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
- [°C]
Max
- [°C]
CU240E-2 F
Description:
Factory setting
- [°C]
Displays the measured Control Unit temperature.
An appropriate message is output when 87 °C is exceeded.
Index:
[0] = Temperature actual
[1] = Temperature maximum
Dependency:
Refer to: A01009
Note:
The value of -200 indicates that there is no measuring signal.
Re r3960[0]:
Displays the currently measured Control Unit temperature.
Re r3960[1]:
Displays the highest measured Control Unit temperature. This value is saved on the module in a non-volatile fashion.
r3974
Drive unit status word / Drv_unit ZSW
Access level: 1
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status word for the drive unit.
Bit field:
Bit
00
01
02
r3978
Description:
Signal name
Software reset active
Writing of parameters disabled as parameter save in progress
Writing of parameters disabled as macro is
running
Factory setting
1 signal
Yes
Yes
0 signal
No
No
FP
-
Yes
No
-
BICO CounterDevice / BICO CounterDevice
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the counter reading for modified BICO interconnections on this device.
The counter is incremented by one for each modified BICO interconnection.
p3981
Faults, acknowledge drive object / Faults ackn DO
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Setting to acknowledge all active faults of a drive object.
Note:
Parameter should be set from 0 to 1 to acknowledge.
Factory setting
0
After acknowledgement, the parameter is automatically reset to 0.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-327
Parameters
List of Parameters
p3985
Master control mode selection / PcCtrl mode select
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Factory setting
0
Description:
Sets the mode to change over the master control / LOCAL mode.
Value:
0:
1:
Danger:
When changing the master control in operation, the drive can manifest undesirable behavior - e.g. it can accelerate
up to another setpoint.
r3986
Parameter count / Parameter No.
Description:
Change master control for STW1.0 = 0
Change master control in operation
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the number of parameters for this drive unit.
The number comprises the device-specific and the drive-specific parameters.
Dependency:
1-328
Refer to: r0980, r0981, r0989
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r3988[0...1]
Description:
Boot state / Boot_state
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
800
Factory setting
-
Index 0:
Displays the boot state.
Index 1:
Displays the partial boot state
Value:
0:
1:
10:
20:
30:
40:
50:
90:
100:
101:
110:
111:
112:
113:
114:
115:
117:
150:
160:
170:
180:
200:
210:
250:
325:
350:
360:
370:
380:
550:
625:
650:
660:
670:
680:
690:
700:
725:
740:
745:
750:
800:
Not active
Fatal fault
Fault
Reset all parameters
Drive object modified
Download using commissioning software
Parameter download using commissioning software
Reset Control Unit
Start initialization
Only for internal Siemens use
Instantiate Control Unit basis
Insert drive object
Only for internal Siemens use
Only for internal Siemens use
Only for internal Siemens use
Parameter download using commissioning software
Only for internal Siemens use
Wait until Power Module is determined
Evaluate Power Module
Instantiate Control Unit reset
Only for internal Siemens use
First commissioning
Create drive packages
Wait for fault acknowledge
Wait for input of drive type
Determine drive type
Only for internal Siemens use
Wait until p0010 is set to 0
Only for internal Siemens use
Call conversion functions for parameter
Wait for non-cyclic start
Start cyclic operation
Evaluate drive commissioning status
Only for internal Siemens use
Only for internal Siemens use
Wait for non-cyclic start
Save parameters
Wait for cyclic
Check the ability to operate
Start cyclic calculations
Interrupt enable
Initialization finished
Index:
[0] = System
[1] = Partial boot
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-329
Parameters
List of Parameters
r3996
Description:
Parameter write inhibit status / Par_write inhib st
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays whether writing to parameters is inhibited.
r3996 = 0:
Parameter write not inhibited.
0 < r3996 < 100:
Parameter write inhibited. The value shows how the calculations are progressing.
r7760
Write protection status / Write prot stat
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status for write protection of adjustable parameters.
Bit field:
Bit
00
Note:
Write protection can be activated/deactivated via p7760 on the Control Unit.
p7761
Write protection / Write protection
Signal name
Write protection active
1 signal
0 signal
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
FP
-
Factory setting
0
Description:
Setting for activating/de-activating the write protection for adjustable parameters.
Value:
0:
1:
Note:
The following parameters are excluded from the write protection:
Inactive
Active
- p0003 (BOP access level)
- p0971 (drive object save parameters)
- p0977 (save all parameters)
- p3950 (service parameters)
- p3981 (acknowledge fault, drive object)
- p7760 (adjustable parameters write protection)
r7841[0...15]
Power Module serial number / PM serial no.
Access level: 4
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the actual serial number of the Power Module.
Notice:
An ASCII table (excerpt) can be found, for example, in the appendix to the List Manual.
The individual characters of the serial number are displayed in the ASCII code in the indices.
1-330
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r7843[0...20]
Description:
Notice:
Note:
r7901[0...43]
Description:
Memory card serial number / Mem_card ser.no
Access level: 4
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the actual serial number of the memory card.
The individual characters of the serial number are displayed in the ASCII code in the indices.
An ASCII table (excerpt) can be found, for example, in the appendix to the List Manual.
Example: displaying the serial number for a memory card:
r7843[0] = 49 dec --> ASCII characters = "1" --> serial number, character 1
r7843[1] = 49 dec --> ASCII characters = "1" --> serial number, character 2
r7843[2] = 49 dec --> ASCII characters = "1" --> serial number, character 3
r7843[3] = 57 dec --> ASCII characters = "9" --> serial number, character 4
r7843[4] = 50 dec --> ASCII characters = "2" --> serial number, character 5
r7843[5] = 51 dec --> ASCII characters = "3" --> serial number, character 6
r7843[6] = 69 dec --> ASCII characters = "E" --> serial number, character 7
r7843[7] = 0 dec --> ASCII characters = " " --> serial number, character 8
...
r7843[19] = 0 dec --> ASCII characters = " " --> serial number, character 20
r7843[20] = 0 dec
Serial number = 111923E
Sampling times / t_sample
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [µs]
Max
- [µs]
Factory setting
- [µs]
Displays the sampling times currently present on the drive unit.
For r7901[x] = 0, the following applies: The time slice is not active.
r7903
Description:
Hardware sampling times still cannot be assigned / HW t_samp free
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the number of hardware sampling times that can still be assigned.
These free sampling times can be used by OA applications such as DCC (Drive Control Chart) or FBLOCKS (free
function blocks).
Note:
r8570[0...39]
OA: Open Architecture
Macro drive object / Macro DO
Access level: 1
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the macro file saved in the appropriate directory on the memory card/device memory.
Dependency:
Refer to: p0015
Note:
For a value = 9999999, the following applies: The read operation is still running.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-331
Parameters
List of Parameters
r8571[0...39]
Macro Binector Input (BI) / Macro BI
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the ACX file saved in the appropriate directory in the non-volatile memory.
Dependency:
Refer to: p0700
Note:
For a value = 9999999, the following applies: The read operation is still running.
r8572[0...39]
Macro Connector Inputs (CI) for speed setpoints / Macro CI n_set
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the ACX file saved in the appropriate directory in the non-volatile memory.
Dependency:
Refer to: p1000
Note:
For a value = 9999999, the following applies: The read operation is still running.
r8573[0...39]
Macro Connector Inputs (CI) for torque setpoints / Macro CI M_set
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the ACX file saved in the appropriate directory in the non-volatile memory.
Dependency:
Refer to: p1500
Note:
For a value = 9999999, the following applies: The read operation is still running.
r8585
Macro execution actual / Macro executed
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the macro currently being executed on the drive object.
Dependency:
Refer to: p0015, p0700, p1000, p1500, r8570, r8571, r8572, r8573
p8991
USB memory access / USB memory
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2
Description:
Selects the storage medium for access via the USB mass storage.
Value:
1:
2:
Note:
A change only becomes effective after a POWER ON.
Factory setting
1
Memory card
Flash r/w internal
The parameter is not influenced by setting the factory setting.
1-332
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p8999
USB functionality / USB functionality
Access level: 4
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
3
Description:
Selecting the USB functionality.
Value:
1:
2:
3:
Note:
COMM: Commissioning.
Factory setting
3
USS commissioning via the virtual COM port
Only memory access
USB commissioning and memory access
A change only becomes effective after a POWER ON.
The parameter is not influenced by setting the factory setting.
p9301
SI Motion enable safety functions (processor 2) / SI Mtn enable P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP F
Factory setting
0000 0000 0000 0000 0000 0000
0000 0000 bin
Description:
Sets the enable signals for the safe motion monitoring.
Bit field:
Bit
00
16
17
30
Dependency:
Refer to: p9501
Signal name
Enable SLS
Enable SSM hysteresis and filtering
Enable SDI
Enable F-DI in PROFIsafe telegram 900
1 signal
Enable
Enable
Enable
Enable
0 signal
Inhibit
Inhibit
Inhibit
Inhibit
FP
2860
2861
-
Refer to: F01682, F01683
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
For bit 30 = 1, PROFIsafe telegram 900 must be configured in the F host.
A change only becomes effective after a POWER ON.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
SLS: Safely-Limited Speed
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-333
Parameters
List of Parameters
p9301
SI Motion enable safety functions (processor 2) / SI Mtn enable P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
0000 0000 0000 0000 0000 0000
0000 0000 bin
Description:
Sets the enable signals for the safe motion monitoring.
Bit field:
Bit
00
17
Dependency:
Refer to: p9501
Refer to: F01682, F01683
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
For bit 30 = 1, PROFIsafe telegram 900 must be configured in the F host.
A change only becomes effective after a POWER ON.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
SLS: Safely-Limited Speed
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
Notice:
Note:
Signal name
Enable SLS
Enable SDI
1 signal
Enable
Enable
0 signal
Inhibit
Inhibit
p9306
SI Motion function specification (processor 2) / SI Mtn fct spec P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
3
FP
2861
Factory setting
1
Description:
Sets the function specification for the safe motion monitoring.
Value:
1:
3:
Dependency:
Refer to: C30711
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
p9307
SI Motion function configuration (processor 2) / SI Mtn config P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
Safety without encoder
Safety without encoder with accel_monitoring/delay time
CU240E-2 DP F
CU240E-2 F
Factory setting
0011 bin
Description:
Sets the function configuration for safe motion monitoring.
Bit field:
Bit
00
01
Dependency:
Notice:
Note:
Refer to: C01711
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Re bit 00:
When the function is activated, a safety-relevant acknowledgement (internal event acknowledge) can be performed
by selecting/deselecting STO.
Re bit 01:
When the function is activated, the active setpoint velocity limit (CO: r9733) is set to zero when STOP F is active.
1-334
Signal name
Extended message acknowledgement
Setpoint velocity limit for STOP F
1 signal
Yes
No
0 signal
No
Yes
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9309
SI Motion behavior during pulse suppression (processor 2) / SI Mtn behav IL P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP F
Factory setting
0000 0000 1111 1111 bin
Description:
Sets the behavior of safety functions and their feedback during pulse suppression in encoderless operation.
Bit field:
Bit
00
08
Signal name
SSM during pulse suppression and sensorless
SDI during pulse suppression and sensorless
1 signal
Becomes inactive
0 signal
Remains active
FP
-
Becomes inactive
Remains active
-
Dependency:
Note:
Refer to: C01711
SDI: Safe Direction (safe motion direction)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
Re bit 00:
For bit = 1 and with the SSM safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the feedback signal has a 0 signal level.
For bit = 0 and with the SSM safety function activated, the following applies:
- Monitoring continues during pulse suppression. The feedback signal last displayed before pulse suppression is
kept and the system goes into the STO state.
Re bit 08:
For bit = 1 and with the SDI safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the status signal indicates inactive.
For bit = 0 and with the SDI safety function activated, the following applies:
- Monitoring continues during pulse suppression. The status signal indicates active and the system goes into the
STO state.
p9309
SI Motion behavior during pulse suppression (processor 2) / SI Mtn behav IL P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
0000 0000 1111 1111 bin
Description:
Sets the behavior of safety functions and their feedback during pulse suppression in encoderless operation.
Bit field:
Bit
08
Dependency:
Refer to: C01711
Note:
SDI: Safe Direction (safe motion direction)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
Re bit 00:
For bit = 1 and with the SSM safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the feedback signal has a 0 signal level.
For bit = 0 and with the SSM safety function activated, the following applies:
- Monitoring continues during pulse suppression. The feedback signal last displayed before pulse suppression is
kept and the system goes into the STO state.
Re bit 08:
For bit = 1 and with the SDI safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the status signal indicates inactive.
For bit = 0 and with the SDI safety function activated, the following applies:
- Monitoring continues during pulse suppression. The status signal indicates active and the system goes into the
STO state.
Signal name
SDI during pulse suppression and sensorless
1 signal
Becomes inactive
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
Remains active
FP
-
1-335
Parameters
List of Parameters
p9321[0...7]
SI Motion gearbox motor/load denominator (processor 2) / SI Mtn gear den P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2147000000
Description:
Index:
Dependency:
Notice:
Factory setting
1
Sets the denominator for the gearbox between the motor and the load.
[0] = Gearbox 1
[1] = Gearbox 2
[2] = Gearbox 3
[3] = Gearbox 4
[4] = Gearbox 5
[5] = Gearbox 6
[6] = Gearbox 7
[7] = Gearbox 8
Refer to: p9322
It is not possible to change over the gearbox stages. Gearbox 1 (index 0) is always active.
p9322[0...7]
SI Motion gearbox motor/load numerator (processor 2) / SI Mtn gear num P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2147000000
Description:
Index:
Dependency:
Notice:
Note:
p9331[0...3]
Factory setting
1
Sets the numerator for the gearbox between the motor and the load.
[0] = Gearbox 1
[1] = Gearbox 2
[2] = Gearbox 3
[3] = Gearbox 4
[4] = Gearbox 5
[5] = Gearbox 6
[6] = Gearbox 7
[7] = Gearbox 8
Refer to: p9321
It is not possible to change over the gearbox stages. Gearbox 1 (index 0) is always active.
In the case of encoderless monitoring functions, the pole pair number must be multiplied by the numerator of the
gearbox ratio.
Example:
Gearbox ratio 1:4, pole pair number (r0313) = 2
--> p9321 = 1, p9322 = 8 (4 x 2)
SI Motion SLS limit values (processor 2) / SI Mtn SLS lim P2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.01 [rpm]
Max
100000.00 [rpm]
Description:
Sets the limit values for the function "Safely-Limited Speed" (SLS).
Index:
[0] = Limit value SLS1
[1] = Limit value SLS2
[2] = Limit value SLS3
[3] = Limit value SLP4
Dependency:
Refer to: p9363, p9531
Factory setting
2000.00 [rpm]
Refer to: C01714
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SLS: Safely-Limited Speed
1-336
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9342
SI Motion act. val. comparison tolerance (crossw.) (processor 2) / SI Mtn actV tol P2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.0010 [°]
Max
360.0000 [°]
Description:
Dependency:
Factory setting
12.0000 [°]
Notice:
Sets the tolerance for the cross-check of the actual position between processor 1 and processor 2.
Refer to: p9542
Refer to: C01711
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
p9345
SI Motion SSM filter time (processor 2) / SI Mtn SSM filt P2
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
100000.00 [µs]
CU240E-2 DP F
Factory setting
0.00 [µs]
Description:
Sets the filter time for the SSM feedback signal to detect standstill.
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
The filter time is effective only if the function is enabled (p9301.16 = p9501.16 = 1).
The parameter is included in the crosswise data comparison of the two monitoring channels.
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
p9346
SI Motion SSM velocity limit (processor 2) / SI Mtn SSM v_limP2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
100000.00 [rpm]
Description:
Dependency:
Caution:
Factory setting
20.00 [rpm]
Sets the velocity limit for the SSM feedback signal to detect standstill (n < nx).
When this limit value is undershot, the signal "SSM feedback signal active" is set.
Refer to: p9546
The following applies for p9306 = 3:
The "SAM" function is switched out if the selected threshold value is undershot.
Notice:
Note:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
p9347
SI Motion SSM velocity hysteresis (processor 2) / SI Mtn SSM Hyst P2
CU240E-2 DP F
Description:
Dependency:
Notice:
Note:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0010 [rpm]
Max
500.0000 [rpm]
Factory setting
10.0000 [rpm]
Sets the velocity hysteresis for the SSM feedback signal to detect standstill (n < nx).
Refer to: C01711
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
The velocity hysteresis is effective only if the function is enabled (p9301.16 = p9501.16 = 1).
The parameter is included in the crosswise data comparison of the two monitoring channels.
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-337
Parameters
List of Parameters
p9348
SI Motion SAM actual velocity tolerance (Motor Module) / SI Mtn SAM tol MM
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
120000.00 [rpm]
Description:
Sets the velocity tolerance for the "SAM" function.
Dependency:
Refer to: p9548
Factory setting
300.00 [rpm]
Refer to: C01706
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
p9351
SI Motion SLS changeover delay time (processor 2) / SI Mtn SLS t P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
600000000.00 [µs]
Description:
Factory setting
100000.00 [µs]
Sets the delay time for the SLS changeover for the function "safely limited speed" (SLS).
When transitioning from a higher to a lower safely-limited velocity/speed stage, within this delay time, the "old"
velocity stage remains active.
Even if SLS is activated from non safety-related operation, then this delay is still applied.
Dependency:
Refer to: p9551
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SLS: Safely-Limited Speed
p9356
SI Motion pulse suppression delay time (processor 2) / SI Mtn IL t_del P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
600000000.00 [µs]
Description:
Factory setting
600000000.00 [µs]
Sets the delay time for the safe pulse suppression after STOP B / SS1.
In the case of encoderless motion monitoring functions with brake ramp monitoring (p9306 = 1), the parameter has
no effect.
Dependency:
Refer to: p9360, p9556
Refer to: C01701
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SS1: Safe Stop 1
p9358
SI Motion acceptance test mode time limit (processor 2) / SI Mtn acc t P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5000000.00 [µs]
Max
100000000.00 [µs]
Description:
Sets the maximum time for the acceptance test mode.
Dependency:
Refer to: p9558
Factory setting
40000000.00 [µs]
If the acceptance test mode takes longer than the selected time limit, then the mode is automatically terminated.
Refer to: C01799
Notice:
1-338
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9360
SI Motion pulse suppression shutdown speed (processor 2) / SI Mtn IL n_sh P2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
10.00 [rpm]
Max
6000.00 [rpm]
Description:
Factory setting
10.00 [rpm]
Sets the shutdown speed for the pulse suppression.
Below this speed "standstill" is assumed and for STOP B / SS1, the pulses are suppressed (by changing to STOP
A).
Dependency:
Refer to: p9356, p9560
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SS1: Safe Stop 1
p9363[0...3]
SI Motion SLS stop response (processor 2) / SI Mtn SLS stop P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Factory setting
0
Sets the stop response for the function "Safely-Limited Speed" (SLS).
These settings apply to the individual limit values for SLS.
Value:
0:
1:
STOP A
STOP B
Index:
[0] = Limit value SLS1
[1] = Limit value SLS2
[2] = Limit value SLS3
[3] = Limit value SLP4
Dependency:
Refer to: p9331, p9563
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SLS: Safely-Limited Speed
p9364
SI Motion SDI tolerance (processor 2) / SI Mtn SDI tol P2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.001 [°]
Max
360.000 [°]
Factory setting
12.000 [°]
Description:
Sets the tolerance for the function "Safe motion direction" (SDI). This motion in the monitored direction is still permissible before an alarm is initiated.
Dependency:
Refer to: p9365, p9366
Refer to: C30716
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive. Sets the tolerance
for the function "Safe motion direction" (SDI).
Note:
SDI: Safe Direction (safe motion direction)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-339
Parameters
List of Parameters
p9365
SI Motion SDI delay time (processor 2) / SI Mtn SDI t P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
600000000.00 [µs]
Factory setting
100000.00 [µs]
Description:
Sets the delay time for the function "Safe motion direction" (SDI). When selecting the SDI function, motion in the
monitored direction is permissible as a maximum for this time; this means that this time can be used for braking
existing motion.
Dependency:
Refer to: p9364, p9366
Refer to: C30716
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SDI: Safe Direction (safe motion direction)
p9366
SI Motion SDI stop response (processor 2) / SI Mtn SDI Stop P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Factory setting
1
Sets the stop response for the function "Safe motion direction" (SDI).
This setting applies to both directions of motion.
Value:
0:
1:
STOP A
STOP B
Dependency:
Refer to: p9364, p9365
Refer to: C30716
Note:
SDI: Safe Direction (safe motion direction)
p9368
SI Motion SAM velocity limit (processor 2) / SI Mtn SAM v_limP2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
1000.00 [rpm]
Description:
Factory setting
0.00 [rpm]
Sets the velocity tolerance limit for the "SAM" function.
SAM is de-activated once the set velocity limit has been undershot.
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
For p9568 = p9368 = 0, the following applies:
The value in p9546/p9346 (SSM) is applied as the velocity limit for SAM.
1-340
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9370
SI Motion acceptance test mode (processor 2) / SI Mtn acc_mod P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
00AC hex
Description:
Setting to select and de-select the acceptance test mode.
Value:
0:
172:
Dependency:
Refer to: p9358, r9371
Factory setting
0000 hex
[00 hex] De-select the acceptance test mode
[AC hex] Select the acceptance test mode
Refer to: C01799
Note:
Acceptance test mode can only be selected if the motion monitoring functions, which are integrated in the drives,
are enabled (p9601.2/p9801.2).
r9371
SI Motion acceptance test status (processor 2) / SI Mtn acc_stat P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
00AC hex
Description:
Displays the status of the acceptance test mode.
Value:
0:
12:
13:
15:
172:
Dependency:
Refer to: p9358, p9370
Factory setting
-
[00 hex] Acc_mode inactive
[0C hex] Acc_mode not possible due to POWER ON fault
[0D hex] Acc_mode not possible due to incorrect ID in p9370
[0F hex] Acc_mode not possible due to expired Acc_timer
[AC hex] Acc_mode active
Refer to: C01799
p9381
SI Motion brake ramp reference value (processor 2) / SI Mtn ramp ref P2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
600.0000 [rpm]
Max
24000.0000 [rpm]
Description:
Factory setting
1500.0000 [rpm]
Sets the reference value to define the brake ramp.
The rate of rise of the brake ramp depends upon p9381 (reference value) and p9383 (monitoring time).
Dependency:
Refer to: p9382, p9383
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
p9382
SI Motion brake ramp delay time (processor 2) / SI Mtn rp t_del P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10000.00 [µs]
Max
99000000.00 [µs]
Description:
Factory setting
250000.00 [µs]
Sets the delay time for monitoring the brake ramp.
Monitoring of the brake ramp starts once the delay time has elapsed.
Dependency:
Refer to: p9381, p9383
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-341
Parameters
List of Parameters
p9383
SI Motion brake ramp monitoring time (processor 2) / SI Mtn rp t_mon P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
500.00 [ms]
Max
1000000.00 [ms]
Description:
Factory setting
10000.00 [ms]
Sets the monitoring time to define the brake ramp.
The rate of rise of the brake ramp depends upon p9381 (reference value) and p9383 (monitoring time).
Dependency:
Refer to: p9381, p9382
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
p9386
SI Motion delay time of the evaluation sensorless (processor 2) / SI Mtn t_del SL MM
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5.00 [ms]
Max
1000.00 [ms]
Description:
Factory setting
100.00 [ms]
Sets the evaluation delay for encoderless actual value sensing after pulse enable.
The value should be greater than or equal to the motor magnetizing time.
Dependency:
Refer to: C01711
p9387
SI Motion encoderless act val sensing filter time (processor 2) / SI Mtn SL filt P2
CU240E-2 DP F
Access level: 4
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
100000.00 [µs]
Factory setting
25000.00 [µs]
Description:
Sets the filter time for smoothing the actual value with sensorless actual value sensing.
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
p9388
SI Motion actual value sensing minimum current (processor 2) / SI Mtn SL I_min P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [%]
Max
1000.00 [%]
Description:
Factory setting
10.00 [%]
Sets the minimum current for encoderless actual value sensing in reference to 10 mA (i.e. when 1 % = 10 mA).
- The value must be increased if C30711 has occurred with message value 1042.
- The value must be decreased if C30711 has occurred with message value 1041.
Dependency:
Refer to: C30711
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Reducing this percentage value can adversely affect actual value sensing.
1-342
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9389
SI Motion voltage tolerance acceleration (processor 2) / SI Mtn U tol P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10.00 [%]
Max
1000.00 [%]
Description:
Factory setting
100.00 [%]
Sets the voltage tolerance for suppressing acceleration peaks.
Increasing this percentage value means that voltage peaks will need to have a higher amplitude during acceleration
procedures if they are not to affect actual value sensing.
- The value must be increased if C30711 has occurred with message value 1042.
- The value must be lowered if acceleration procedures have led to an excessive Safety actual velocity.
Dependency:
Refer to: C30711
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
r9398[0...1]
SI Motion actual checksum SI parameters (processor 2) / SI Mtn act CRC P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the checksum over the checked Safety Integrated parameters of the motion monitoring functions (actual
checksum) on processor 2.
Index:
[0] = Checksum over SI parameters for motion monitoring
[1] = Checksum over SI parameters with hardware reference
Dependency:
Refer to: p9399
p9399[0...1]
SI Motion setpoint checksum SI parameters (processor 2) / SI Mtn setp CRC P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
Factory setting
0000 hex
Description:
Sets the checksum over the checked Safety Integrated parameters of the motion monitoring functions (actual
checksum) on processor 2.
Index:
[0] = Checksum over SI parameters for motion monitoring
[1] = Checksum over SI parameters with hardware reference
Dependency:
Refer to: r9398
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-343
Parameters
List of Parameters
p9400
Description:
Safely remove memory card / Mem_card rem
Access level: 2
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
100
Factory setting
0
Setting and display when memory card is "removed safely".
Procedure:
Setting p9400 = 2 results in a value of 3
--> The memory card can be removed safely. After removal the value sets itself to 0 automatically.
Setting p9400 = 2 results in a value of 100
--> The memory card cannot be removed safely. Removal may destroy the file system on the memory card. It may
be necessary to set p9400 = 2 again.
Value:
0:
1:
2:
3:
100:
No memory card inserted
Memory card inserted
Request "safe removal" of the memory card
"Safe removal" possible
"Safe removal" not possible due to access
Dependency:
Refer to: r9401
Caution:
Removing the memory card without a request (p9400 = 2) and confirmation (p9400 = 3) may destroy the file system
on the memory card. The memory card will then no longer work properly and must be repaired.
Note:
The status when the memory card is being "removed safely" is shown in r9401.
Re value = 0, 1, 3, 100:
These values can only be displayed, not set.
r9401
Safely remove memory card status / Mem_card rem stat
Access level: 2
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Displays the status of the memory card.
Bit field:
Bit
00
01
Dependency:
Refer to: p9400
Note:
Re bit 00 and bit 01:
Signal name
Memory card inserted
Memory card activated
Factory setting
1 signal
Yes
Yes
0 signal
No
No
FP
-
Bit 1/0 = 0/0: No memory card inserted (corresponds to p9400 = 0).
Bit 1/0 = 0/1: "Safe removal" possible (corresponds to p9400 = 3).
Bit 1/0 = 1/0: Status not possible.
Bit 1/0 = 1/1: Memory card inserted (corresponds to p9400 = 1, 2, 100).
1-344
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9406[0...19]
Description:
Dependency:
Note:
r9407[0...19]
Description:
Dependency:
Note:
r9408[0...19]
Description:
Dependency:
Note:
PS file parameter number parameter not transferred / PS par_no n transf
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the parameters that were not able to be transferred when reading the parameter back-up files (PS files)
from the non-volatile memory (e.g. memory card).
r9406[0] = 0
--> All of the parameter values were able to be transferred error-free.
r9406[0...x] > 0
--> indicates the parameter number in the following cases:
- parameter, whose value was not able to be completely accepted.
- indexed parameter, where at least 1 index was not able to be accepted. The first index that is not transferred is
displayed in r9407.
Refer to: r9407, r9408
All indices from r9406 to r9408 designate the same parameter.
r9406[x] parameter number, parameter not accepted
r9407[x] parameter index, parameter not accepted
r9408[x] fault code, parameter not accepted
PS file parameter index parameter not transferred / PS parameter index
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the first index of the parameters that could not be transferred when the parameter backup files (PS files)
were read from the non-volatile memory (e.g. memory card).
If, from an indexed parameter, at least one index was not able to be transferred, then the parameter number is displayed in r9406[n] and the first index that was not transferred is displayed in r9407[n].
r9406[0] = 0
--> All of the parameter values were able to be transferred error-free.
r9406[n] > 0
--> Displays r9407[n] the first index of the parameter number r9406[n] that was not transferred.
Refer to: r9406, r9408
All indices from r9406 to r9408 designate the same parameter.
r9406[x] parameter number, parameter not accepted
r9407[x] parameter index, parameter not accepted
r9408[x] fault code, parameter not accepted
PS file fault code parameter not transferred / PS fault code
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Only for internal Siemens service purposes.
Refer to: r9406, r9407
All indices from r9406 to r9408 designate the same parameter.
r9406[x] parameter number, parameter not accepted
r9407[x] parameter index, parameter not accepted
r9408[x] fault code, parameter not accepted
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-345
Parameters
List of Parameters
r9409
Number of parameters to be saved / Qty par to save
Access level: 4
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the number of modified parameters and those that have still not be saved for this drive object.
Dependency:
Refer to: p0971
Note:
The modified parameters that still need to be saved are internally listed in r9410 ... r9419.
r9451[0...29]
Units changeover adapted parameters / Unit_chngov par
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the parameters whose parameter would have to be changed during a units changeover.
Dependency:
Refer to: F07088
r9463
Set valid macro /
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
999999
Factory setting
-
Displays the valid macro.
A value of 0 is displayed if a parameter set by a macro is changed.
p9484
Description:
BICO interconnections search signal source / BICO S_src srch
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
4294967295
Factory setting
0
Sets the signal source (BO/CO parameter, BICO coded) to search in the signal sinks.
The signal source to be searched for is set in p9484 (BICO-coded) and the search result is specified using the number (r9485) and the first index (r9486).
Dependency:
Refer to: r9485, r9486
r9485
BICO interconnections signal source search count / BICO S_src srchQty
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the number of BICO interconnections to the signal sink being searched for.
Dependency:
Refer to: p9484, r9486
Note:
The signal source to be searched is set in p9484 (BICO-coded).
The search result is contained in r9482 and r9483 and is specified by the count (r9485) and the first index (r9486).
1-346
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9486
Description:
Dependency:
Note:
BICO interconnections signal source search first index / BICO S_src srchIdx
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the first index of the signal source being searched for.
The signal source to be searched for is set in p9484 (BICO-coded) and the search result is specified using the number (r9485) and the first index (r9486).
Refer to: p9484, r9485
The signal source to be searched is set in p9484 (BICO-coded).
The search result is contained in r9482 and r9483 and is specified by the count (r9485) and the first index (r9486).
p9501
SI Motion enable safety functions (processor 1) / SI Mtn enable P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP F
Factory setting
0000 0000 0000 0000 0000 0000
0000 0000 bin
Description:
Sets the enable signals for the safe motion monitoring.
Bit field:
Bit
00
16
17
30
Dependency:
Note:
Refer to: F01682, F01683
For bit 30 = 1, PROFIsafe telegram 900 must be configured in the F host.
A change only becomes effective after a POWER ON.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
SLS: Safely-Limited Speed
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
p9501
SI Motion enable safety functions (processor 1) / SI Mtn enable P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
Signal name
Enable SLS
Enable SSM hysteresis and filtering
Enable SDI
Enable F-DI in PROFIsafe telegram 900
1 signal
Enable
Enable
Enable
Enable
0 signal
Inhibit
Inhibit
Inhibit
Inhibit
FP
2860
2861
-
CU240E-2 F
Factory setting
0000 0000 0000 0000 0000 0000
0000 0000 bin
Description:
Sets the enable signals for the safe motion monitoring.
Bit field:
Bit
00
17
Dependency:
Note:
Refer to: F01682, F01683
For bit 30 = 1, PROFIsafe telegram 900 must be configured in the F host.
A change only becomes effective after a POWER ON.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
SLS: Safely-Limited Speed
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
Signal name
Enable SLS
Enable SDI
1 signal
Enable
Enable
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
Inhibit
Inhibit
FP
2861
1-347
Parameters
List of Parameters
p9506
SI Motion function specification (processor 1) / SI Mtn fct_spc P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
3
Factory setting
1
Description:
Sets the function specification for the safe motion monitoring.
Value:
1:
3:
Dependency:
Refer to: C01711
p9507
SI Motion function configuration (processor 1) / SI Mtn config P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
Safety without encoder
Safety without encoder with accel_monitoring/delay time
CU240E-2 DP F
CU240E-2 F
Factory setting
0011 bin
Description:
Sets the function configuration for safe motion monitoring.
Bit field:
Bit
00
01
Dependency:
Refer to: C01711
Note:
Re bit 00:
Signal name
Extended message acknowledgement
Setpoint velocity limit for STOP F
1 signal
Yes
No
0 signal
No
Yes
FP
-
When the function is activated, a safety-relevant acknowledgement (internal event acknowledge) can be performed
by selecting/deselecting STO.
Re bit 01:
When the function is activated, the active setpoint velocity limit (CO: r9733) is set to zero when STOP F is active.
1-348
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9509
SI Motion behavior during pulse suppression (processor 1) / SI Mtn behav IL P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP F
Factory setting
0000 0000 1111 1111 bin
Description:
Sets the behavior of safety functions and their feedback during pulse suppression in encoderless operation.
Bit field:
Bit
00
08
Signal name
SSM during pulse suppression and
sensorless
SDI during pulse suppression and
sensorless
1 signal
Becomes inactive
0 signal
Remains active
FP
-
Becomes inactive
Remains active
-
Dependency:
Note:
Refer to: C01711
SDI: Safe Direction (safe motion direction)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
Re bit 00:
For bit = 1 and with the SSM safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the feedback signal has a 0 signal level.
For bit = 0 and with the SSM safety function activated, the following applies:
- Monitoring continues during pulse suppression. The feedback signal last displayed before pulse suppression is
kept and the system goes into the STO state.
Re bit 08:
For bit = 1 and with the SDI safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the status signal indicates inactive.
For bit = 0 and with the SDI safety function activated, the following applies:
- Monitoring continues during pulse suppression. The status signal indicates active and the system goes into the
STO state.
p9509
SI Motion behavior during pulse suppression (processor 1) / SI Mtn behav IL P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
0000 0000 1111 1111 bin
Description:
Sets the behavior of safety functions and their feedback during pulse suppression in encoderless operation.
Bit field:
Bit
08
Dependency:
Refer to: C01711
Note:
SDI: Safe Direction (safe motion direction)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
Re bit 00:
For bit = 1 and with the SSM safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the feedback signal has a 0 signal level.
For bit = 0 and with the SSM safety function activated, the following applies:
- Monitoring continues during pulse suppression. The feedback signal last displayed before pulse suppression is
kept and the system goes into the STO state.
Re bit 08:
For bit = 1 and with the SDI safety function activated, the following applies:
- During pulse suppression, monitoring is switched off and the status signal indicates inactive.
For bit = 0 and with the SDI safety function activated, the following applies:
- Monitoring continues during pulse suppression. The status signal indicates active and the system goes into the
STO state.
Signal name
SDI during pulse suppression and sensorless
1 signal
Becomes inactive
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
Remains active
FP
-
1-349
Parameters
List of Parameters
p9521[0...7]
SI Motion gearbox motor/load denominator (processor 1) / SI Mtn gear den P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2147000000
Factory setting
1
Description:
Sets the denominator for the gearbox between the motor and the load.
Index:
[0] = Gearbox 1
[1] = Gearbox 2
[2] = Gearbox 3
[3] = Gearbox 4
[4] = Gearbox 5
[5] = Gearbox 6
[6] = Gearbox 7
[7] = Gearbox 8
Dependency:
Refer to: p9522
Notice:
It is not possible to change over the gearbox stages. Gearbox 1 (index 0) is always active.
p9522[0...7]
SI Motion gearbox motor/load numerator (processor 1) / SI Mtn gear num P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
2147000000
Description:
Index:
Dependency:
Notice:
Note:
p9531[0...3]
Factory setting
1
Sets the numerator for the gearbox between the motor and the load.
[0] = Gearbox 1
[1] = Gearbox 2
[2] = Gearbox 3
[3] = Gearbox 4
[4] = Gearbox 5
[5] = Gearbox 6
[6] = Gearbox 7
[7] = Gearbox 8
Refer to: p9521
It is not possible to change over the gearbox stages. Gearbox 1 (index 0) is always active.
In the case of encoderless monitoring functions, the pole pair number must be multiplied by the numerator of the
gearbox ratio.
Example:
Gearbox ratio 1:4, pole pair number (r0313) = 2
--> p9521 = 1, p9522 = 8 (4 x 2)
SI Motion SLS limit values (processor 1) / SI Mtn SLS lim P1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.01 [rpm]
Max
100000.00 [rpm]
Description:
Index:
Dependency:
Note:
1-350
Factory setting
2000.00 [rpm]
Sets the limit values for the function "Safely-Limited Speed" (SLS).
[0] = Limit value SLS1
[1] = Limit value SLS2
[2] = Limit value SLS3
[3] = Limit value SLP4
Refer to: p9563
Refer to: C01714
SLS: Safely-Limited Speed
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9533
SI Motion SLS setpoint speed limit (processor 1) / SI Mtn SLS set_lim
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.000 [%]
Max
100.000 [%]
Factory setting
80.000 [%]
Description:
This is an evaluation factor to define the setpoint limit from the selected actual speed limit.
Dependency:
This parameter only has to be parameterized for the motion monitoring functions integrated in the drive (p9601.2 =
1)
The active SLS limit value is evaluated with this factor and is made available as setpoint limit in r9733.
r9733[0] = p9531[x] x p9533 (converted from the load side to the motor side)
r9733[1] = - p9531[x] x p9533 (converted from the load side to the motor side)
[x] = Selected SLS stage
Conversion factor from the motor side to the load side:
- motor type = rotary and axis type = linear: p9522 / (p9521 x p9520)
- otherwise: p9522 / p9521
Refer to: p9501, p9531, p9601
Note:
The active actual speed limit is selected via PROFIsafe.
With STOP A, B, setpoint 0 is specified in r9733.
If p9533 = 0 is set, the setpoint speed limit is de-activated, and r9733[0] = p1082 and r9733[1] = -p1082 are set
SLS: Safely-Limited Speed
p9542
SI Motion act. val. comparison tolerance (crossw.) (processor 1) / SI Mtn act tol P1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.0010 [°]
Max
360.0000 [°]
Factory setting
12.0000 [°]
Description:
Sets the tolerance for the cross-check of the actual position between processor 1 and processor 2.
Dependency:
Refer to: C01711
p9545
SI Motion SSM filter time (processor 1) / SI Mtn SSM filt P1
PM240
Access level: 3
Calculated: -
Data type: FloatingPoint32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
100.00 [ms]
CU240E-2 DP F
Description:
Sets the filter time for the SSM feedback signal to detect standstill.
Note:
The filter time is effective only if the function is enabled (p9501.16 = 1).
Factory setting
0.00 [ms]
The parameter is included in the crosswise data comparison of the two monitoring channels.
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-351
Parameters
List of Parameters
p9546
SI Motion SSM velocity limit (processor 1) / SI Mtn SSM v_limP1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
100000.00 [rpm]
Description:
Factory setting
20.00 [rpm]
Sets the velocity limit for the SSM feedback signal to detect standstill (n < nx).
When this limit value is undershot, the signal "SSM feedback signal active" is set.
Caution:
The following applies for p9506 = 3:
The "SAM" function is switched out if the selected threshold value is undershot.
Note:
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
p9547
CU240E-2 DP F
SI Motion SSM velocity hysteresis (processor 1) / SI Mtn SSM hyst P1
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.0010 [rpm]
Max
500.0000 [rpm]
Factory setting
10.0000 [rpm]
Description:
Sets the velocity hysteresis for the SSM feedback signal to detect standstill (n < nx).
Dependency:
Refer to: C01711
Note:
The velocity hysteresis is effective only if the function is enabled (p9501.16 = 1).
The parameter is included in the crosswise data comparison of the two monitoring channels.
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
p9548
SI Motion SAM actual velocity tolerance (Control Unit) / SI Mtn SAM tol CU
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
120000.00 [rpm]
Factory setting
300.00 [rpm]
Description:
Sets the velocity tolerance for the "SAM" function.
Dependency:
Refer to: C01706
Note:
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
p9551
SI Motion SLS changeover delay time (processor 1) / SI Mtn SLS t P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
600000.00 [ms]
Description:
Factory setting
100.00 [ms]
Sets the delay time for the SLS changeover for the function "safely limited speed" (SLS).
When transitioning from a higher to a lower safely-limited velocity/speed stage, within this delay time, the "old"
velocity stage remains active.
Even if SLS is activated from non safety-related operation, then this delay is still applied.
Note:
1-352
SLS: Safely-Limited Speed
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9556
SI Motion pulse suppression delay time (processor 1) / SI Mtn IL t_del P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
600000.00 [ms]
Description:
Factory setting
600000.00 [ms]
Sets the delay time for the safe pulse suppression after STOP B.
In the case of encoderless motion monitoring functions with brake ramp monitoring (p9506 = 1), the parameter has
no effect.
Dependency:
Refer to: p9560
Refer to: C01701
p9558
SI Motion acceptance test mode time limit (processor 1) / SI Mtn acc t P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5000.00 [ms]
Max
100000.00 [ms]
Factory setting
40000.00 [ms]
Description:
Sets the maximum time for the acceptance test mode.
Dependency:
Refer to: C01799
p9559
SI Motion forced checking procedure timer (processor 1) / SI Mtn dyn timer
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [h]
Max
9000.00 [h]
If the acceptance test mode takes longer than the selected time limit, then the mode is automatically terminated.
Description:
Factory setting
8.00 [h]
Sets the time interval for carrying out the forced checking procedure and testing the safety motion monitoring functions integrated in the drives.
Within the parameterized time, the safety functions must have been tested at least once (including de-selection of
the "STO" function).
This monitoring time is reset each time the test is carried out.
The signal source to initiate the forced checking procedure is set in p9705.
Dependency:
Refer to: p9705
Refer to: A01697, C01798
Note:
STO: Safe Torque Off
p9560
SI Motion pulse suppression shutdown speed (processor 1) / SI Mtn IL v_sh P1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
10.00 [rpm]
Max
6000.00 [rpm]
Description:
Factory setting
10.00 [rpm]
Sets the shutdown speed for the pulse suppression.
Below this speed "standstill" is assumed and for STOP B, the pulses are suppressed by changing to STOP A).
Dependency:
Refer to: p9556
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-353
Parameters
List of Parameters
p9563[0...3]
SI Motion SLS-specific stop response (processor 1) / SI Mtn SLS stop P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Factory setting
0
Sets the SLS-specific stop response for the function "Safely-Limited Speed" (SLS).
These settings apply to the individual limit values for SLS.
Value:
0:
1:
STOP A
STOP B
Index:
[0] = Limit value SLS1
[1] = Limit value SLS2
[2] = Limit value SLS3
[3] = Limit value SLP4
Dependency:
Refer to: p9531
Note:
SLS: Safely-Limited Speed
p9564
SI Motion SDI tolerance (processor 1) / SI Mtn SDI tol P1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.001 [°]
Max
360.000 [°]
Factory setting
12.000 [°]
Description:
Sets the tolerance for the function "Safe motion direction" (SDI). This motion in the monitored direction is still permissible before an alarm is initiated.
Dependency:
Refer to: p9565, p9566
Refer to: C01716
Note:
SDI: Safe Direction (safe motion direction)
p9565
SI Motion SDI delay time (processor 1) / SI Mtn SDI t P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
600000.00 [ms]
Factory setting
100.00 [ms]
Description:
Sets the delay time for the function "Safe motion direction" (SDI). When selecting the SDI function, motion in the
monitored direction is permissible as a maximum for this time; this means that this time can be used for braking
existing motion.
Dependency:
Refer to: p9564, p9566
Refer to: C01716
Note:
1-354
SDI: Safe Direction (safe motion direction)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9566
SI Motion SDI stop response (processor 1) / SI Mtn SDI Stop P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
1
Description:
Factory setting
1
Sets the stop response for the function "Safe motion direction" (SDI).
This setting applies to both directions of motion.
Value:
0:
1:
STOP A
STOP B
Dependency:
Refer to: p9564, p9565
Refer to: C01716
Note:
SDI: Safe Direction (safe motion direction)
p9568
SI Motion SAM velocity limit (processor 1) / SI Mtn SAM v_limP1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
0.00 [rpm]
Max
1000.00 [rpm]
Description:
Factory setting
0.00 [rpm]
Sets the velocity tolerance limit for the "SAM" function.
SAM is de-activated once the set velocity limit has been undershot.
Note:
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
SSM: Safe Speed Monitor (safety-relevant feedback signal from the velocity monitoring)
For p9568 = p9368 = 0, the following applies:
The value in p9546/p9346 (SSM) is applied as the velocity limit for SAM.
p9570
SI Motion acceptance test mode (processor 1) / SI Mtn acc_mod P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
00AC hex
Description:
Setting to select and de-select the acceptance test mode.
Value:
0:
172:
Dependency:
Refer to: p9558, r9571, p9601
Factory setting
0000 hex
[00 hex] De-select the acceptance test mode
[AC hex] Select the acceptance test mode
Refer to: C01799
Note:
Acceptance test mode can only be selected if the motion monitoring functions, which are integrated in the drives,
are enabled (p9601.2/p9801.2).
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-355
Parameters
List of Parameters
r9571
SI Motion acceptance test status (processor 1) / SI Mtn acc_status
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
00AC hex
Description:
Displays the status of the acceptance test mode.
Value:
0:
12:
13:
15:
172:
Dependency:
Refer to: p9558, p9570
Factory setting
-
[00 hex] Acc_mode inactive
[0C hex] Acc_mode not possible due to POWER ON fault
[0D hex] Acc_mode not possible due to incorrect ID in p9570
[0F hex] Acc_mode not possible due to expired Acc_timer
[AC hex] Acc_mode active
Refer to: C01799
p9581
SI Motion brake ramp reference value (processor 1) / SI Mtn ramp ref P1
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
600.0000 [rpm]
Max
24000.0000 [rpm]
Description:
Factory setting
1500.0000 [rpm]
Sets the reference value to define the brake ramp.
The rate of rise of the brake ramp depends upon p9581 (reference value) and p9583 (monitoring time).
Dependency:
Refer to: p9582, p9583
p9582
SI Motion brake ramp delay time (processor 1) / SI Mtn ramp t P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10.00 [ms]
Max
99000.00 [ms]
Description:
Factory setting
250.00 [ms]
Sets the delay time for monitoring the brake ramp.
Monitoring of the brake ramp starts once the delay time has elapsed.
Dependency:
Refer to: p9581, p9583
p9583
SI Motion brake ramp monitoring time (processor 1) / SI Mtn rp t_mon P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.50 [s]
Max
1000.00 [s]
Description:
Factory setting
10.00 [s]
Sets the monitoring time to define the brake ramp.
The rate of rise of the brake ramp depends upon p9581 (reference value) and p9583 (monitoring time).
Dependency:
1-356
Refer to: p9581, p9582
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9586
SI Motion delay time of the evaluation sensorless (CU) / SI Mtn t_del SL CU
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5.00 [ms]
Max
1000.00 [ms]
Factory setting
100.00 [ms]
Description:
Sets the evaluation delay for encoderless actual value sensing after pulse enable. The value should be greater than
or equal to the motor magnetizing time. Shortening the time can result in Alarm 1711 with fault value 1041 or1042.
Dependency:
Refer to: C01711
Notice:
Reducing this value can adversely affect the actual value sensing and the plausibility check.
Note:
This parameter is only effective for encoderless actual value sensing (p9306/p9506 = 1).
p9587
SI Motion encoderless act val sensing filter time (processor 1) / SI Mtn SL filt P1
CU240E-2 DP F
Access level: 4
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
100.00 [ms]
When the value is increased, this results in a longer evaluation delay.
Factory setting
25.00 [ms]
Description:
Sets the filter time for smoothing the actual value with sensorless actual value sensing.
p9588
SI Motion act val sensing sensorless min current (processor 1) / SI Mtn SL I_min P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [%]
Max
1000.00 [%]
Description:
Factory setting
10.00 [%]
Sets the minimum current for encoderless actual value sensing in reference to 10 mA (i.e. when 1 % = 10 mA).
- The value must be increased if C01711 has occurred with message value 1042.
- The value must be decreased if C01711 has occurred with message value 1041.
Dependency:
Refer to: C01711
Notice:
Reducing this percentage value can adversely affect actual value sensing.
p9589
SI Motion voltage tolerance acceleration (processor 1) / SI Mtn U tol P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
10.00 [%]
Max
1000.00 [%]
Description:
Factory setting
100.00 [%]
Sets the voltage tolerance for suppressing acceleration peaks.
Increasing this percentage value means that voltage peaks will need to have a higher amplitude during acceleration
procedures if they are not to affect actual value sensing.
- The value must be increased if C01711 has occurred with message value 1043.
- The value must be lowered if acceleration procedures have led to an excessive Safety actual velocity.
Dependency:
Refer to: C01711
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-357
Parameters
List of Parameters
r9590[0...3]
SI Motion version safety motion monitoring (processor 1) / SI Mtn version P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the Safety Integrated version for the safe monitoring functions.
Index:
[0] = Safety Version (major release)
[1] = Safety Version (minor release)
[2] = Safety Version (baselevel or patch)
[3] = Safety Version (hotfix)
Dependency:
Refer to: r9770
Note:
Example:
r9590[0] = 2, r9590[1] = 60, r9590[2] = 1, r9590[3] = 0 --> SI Motion version V02.60.01.00
p9601
SI enable, functions integrated in the drive (processor 1) / SI enable fct P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2
Description:
Factory setting
0000 bin
Sets the enable signals for safety functions on processor 1 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9601 = 0: Safety functions integrated in the drive disabled.
- p9601 = 1: STO enabled via terminals. Permissible if r9771.0 = 1.
- p9601 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9771.5 = 1.
- p9601 = 8: STO enabled via PROFIsafe. Permissible if r9771.6 = 1.
- p9601 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9771.6 = 1.
- p9601 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9771.4 = 1.
- p9601 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9771.4 = 1.
Bit field:
Bit
00
Signal name
Enable STO via terminals (processor 1)
1 signal
Enable
Dependency:
Refer to: r9771, p9801
Note:
A change only becomes effective after a POWER ON.
0 signal
Inhibit
FP
2810
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
1-358
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9601
SI enable, functions integrated in the drive (processor 1) / SI enable fct P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP
Description:
Factory setting
0000 bin
Sets the enable signals for safety functions on processor 1 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9601 = 0: Safety functions integrated in the drive disabled.
- p9601 = 1: STO enabled via terminals. Permissible if r9771.0 = 1.
- p9601 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9771.5 = 1.
- p9601 = 8: STO enabled via PROFIsafe. Permissible if r9771.6 = 1.
- p9601 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9771.6 = 1.
- p9601 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9771.4 = 1.
- p9601 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9771.4 = 1.
Bit field:
Bit
00
03
Signal name
Enable STO via terminals (processor 1)
Enable PROFIsafe (processor 1)
1 signal
Enable
Enable
Dependency:
Refer to: r9771, p9801
Note:
A change only becomes effective after a POWER ON.
0 signal
Inhibit
Inhibit
FP
2810
-
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
p9601
SI enable, functions integrated in the drive (processor 1) / SI enable fct P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP F
Description:
Factory setting
0000 bin
Sets the enable signals for safety functions on processor 1 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9601 = 0: Safety functions integrated in the drive disabled.
- p9601 = 1: STO enabled via terminals. Permissible if r9771.0 = 1.
- p9601 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9771.5 = 1.
- p9601 = 8: STO enabled via PROFIsafe. Permissible if r9771.6 = 1.
- p9601 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9771.6 = 1.
- p9601 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9771.4 = 1.
- p9601 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9771.4 = 1.
Bit field:
Bit
00
02
Dependency:
Refer to: r9771, p9801
Note:
A change only becomes effective after a POWER ON.
03
Signal name
Enable STO via terminals (processor 1)
Motion monitoring functions integr. in the
drive (processor 1)
Enable PROFIsafe (processor 1)
1 signal
Enable
Enable
0 signal
Inhibit
Inhibit
FP
2810
-
Enable
Inhibit
-
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-359
Parameters
List of Parameters
p9601
SI enable, functions integrated in the drive (processor 1) / SI enable fct P1
PM240
Access level: 3
Calculated: -
Data type: Unsigned32
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
0000 bin
Sets the enable signals for safety functions on processor 1 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9601 = 0: Safety functions integrated in the drive disabled.
- p9601 = 1: STO enabled via terminals. Permissible if r9771.0 = 1.
- p9601 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9771.5 = 1.
- p9601 = 8: STO enabled via PROFIsafe. Permissible if r9771.6 = 1.
- p9601 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9771.6 = 1.
- p9601 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9771.4 = 1.
- p9601 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9771.4 = 1.
Bit field:
Bit
00
02
Signal name
Enable STO via terminals (processor 1)
Motion monitoring functions integr. in the
drive (processor 1)
1 signal
Enable
Enable
Dependency:
Refer to: r9771, p9801
Note:
A change only becomes effective after a POWER ON.
0 signal
Inhibit
Inhibit
FP
2810
-
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
p9610
SI PROFIsafe address (processor 1) / SI PROFIsafe P1
CU240E-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFE hex
Factory setting
0000 hex
Description:
Sets the PROFIsafe address for processor 1.
Dependency:
Refer to: p9810
p9650
SI F-DI changeover tolerance time (processor 1) / SI F-DI_chg tol P1
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
2000.00 [ms]
CU240E-2 F
Description:
Factory setting
500.00 [ms]
Sets the tolerance time for the changeover of the failsafe digital input for STO on processor 1.
An F-DI changeover is not effective simultaneously due to the different runtimes in the two monitoring channels.
After an F-DI changeover, dynamic data is not subject to a crosswise data comparison during this tolerance time.
Dependency:
Refer to: p9850
Note:
For a crosswise data comparison between p9650 and p9850, a difference of one Safety monitoring clock cycle is
tolerated.
The parameterized time is internally rounded-off to an integer multiple of the monitoring clock cycle.
F-DI: Failsafe Digital Input
1-360
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9651
SI STO debounce time (processor 1) / SI STO t_debou P1
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
100.00 [ms]
CU240E-2 F
Description:
Factory setting
1.00 [ms]
Sets the debounce time for the failsafe digital inputs used to control the "STO" function.
The debounce time is rounded to whole milliseconds.
Note:
The debounce time is rounded to whole milliseconds. It specifies the maximum duration of a fault pulse at the failsafe digital inputs with no reaction/influence on the selection or deselection of the Safety Basic Functions.
Example:
Debounce time = 1 ms: Fault pulses of 1 ms are filtered; only pulses longer than 2 ms are processed.
Debounce time = 3 ms: Fault pulses of 3 ms are filtered; only pulses longer than 4 ms are processed.
p9659
SI forced checking procedure timer / SI FrcdCkProcTimer
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.00 [h]
Max
9000.00 [h]
CU240E-2 F
Description:
Factory setting
8.00 [h]
Sets the time interval for carrying out the forced checking procedure and testing the Safety shutdown paths.
Within the parameterized time, STO must have been de-selected at least once. The monitoring time is reset each
time that STO is de-selected.
Dependency:
Refer to: A01699
Note:
STO: Safe Torque Off
r9660
SI forced checking procedure remaining time / SI frc chk remain
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
- [h]
Max
- [h]
CU240E-2 F
Factory setting
- [h]
Description:
Displays the time remaining before dynamization and testing of the safety shutdown paths (forced checking procedure).
Dependency:
Refer to: A01699
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-361
Parameters
List of Parameters
p9700
SI copy function / SI copy function
CU240E-2
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: C(95), U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
00D0 hex
CU240E-2 F
Description:
Factory setting
0000 hex
Setting to start the required copy function.
After starting, the corresponding parameters are copied from processor 1 to processor 2.
Once copying is complete, the parameter is automatically reset to zero.
Value:
0:
29:
87:
208:
[00 hex] Copy function ended
[1D hex] Start copy function node identifier
[57 hex] Start copy function SI parameters
[D0 hex] Start copy function SI basic parameters
Dependency:
Refer to: r3996
Notice:
When the parameters are copied, short-term communication interruptions may occur.
Note:
Re value = 57 hex and D0 hex:
The value can only be set if the safety commissioning mode is set and the Safety Integrated password was entered.
Re value = D0 hex:
The following parameters are copied after starting the copy function:
p9601 --> p9801, p9610 --> 9810, p9650 --> p9850, p9651 --> p9851
p9701
Acknowledge SI data change / Ackn SI data
CU240E-2
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 DP
Can be changed: C(95), U, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
00EC hex
CU240E-2 F
Description:
Factory setting
0000 hex
Setting to transfer the reference checksums from the associated actual checksums after changes (SI parameters,
hardware).
After transferring the reference checksums, parameters are automatically reset to zero.
Value:
0:
172:
220:
236:
[00 hex] Data unchanged
[AC hex] Acknowledge data change complete
[DC hex] Acknowledge SI basic parameter change
[EC hex] Acknowledge hardware CRC
Dependency:
Refer to: r9398, p9399, r9728, p9729, r9798, p9799, r9898, p9899
Note:
Re value = AC and DC hex:
These values can only be set if the safety commissioning mode is set and the Safety Integrated password was
entered.
p9705
BI: SI Motion: Test stop signal source / SI Mtn test stop
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: U32 / Binary
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
1-362
Factory setting
0
Sets the signal source for the test stop of the safety-relevant motion monitoring functions.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9710[0...1]
SI Motion diagnostics result list 1 / SI Mtn res_list 1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays result list 1 that, for the crosswise data comparison between the monitoring channels, led to the fault.
Index:
[0] = Result list processor 2
[1] = Result list processor 1
Bit field:
Bit
06
07
08
09
10
11
12
13
16
17
18
19
20
21
Dependency:
Refer to: C01711
Note:
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
Signal name
Actual value > upper limit, SLS1
Actual value > lower limit, SLS1
Actual value > upper limit, SLS2
Actual value > lower limit, SLS2
Actual value > upper limit, SLS3
Actual value > lower limit, SLS3
Actual value > upper limit, SLS4
Actual value > lower limit, SLS4
Actual value > upper limit, SAM/SBR
Actual value > lower limit, SAM/SBR
Actual value > upper limit SDI positive
Actual value > lower limit SDI positive
Actual value > upper limit SDI negative
Actual value > lower limit SDI negative
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
No
No
No
No
No
No
FP
-
SBR: Safe Brake Ramp (safe brake ramp monitoring)
SLS: Safely-Limited Speed
r9712
SI Motion diagnostics pos. act. val. motor side (processor 1) / SI Mtn s_act motP1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the current motor-side position actual value for the motion monitoring functions on processor 1.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-363
Parameters
List of Parameters
r9713[0...3]
SI Motion diagnostics position actual value load side / SI Mtn s_act load
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the actual load-side actual values of both monitoring channels and their difference.
Index:
[0] = Load-side actual value on processor 1 (P1)
[1] = Load-side actual value on processor 2 (P2)
[2] = Load-side actual value difference P1 - P2
[3] = Load-side maximum actual value difference P1 - P2
Dependency:
Refer to: r9724
Note:
Re index 0:
The display of the load-side position actual value on processor 1 is updated in the monitoring clock cycle.
Re index 1:
The display of the load-side position actual value on processor 2 is updated in the CDC clock cycle (r9724) and
delayed by one CDC clock cycle.
Re index 2:
The difference between the load-side position actual value on processor 1 and load-side position actual value on
processor 2 is updated in the CDC clock cycle (r9724) and delayed by one CDC clock cycle.
Re index 3:
The maximum difference between the load-side position actual value on processor 1 and the load-side position
actual value on processor 2.
CDC: Crosswise Data Check
r9714[0...1]
SI Motion diagnostics velocity (processor 1) / SI Mtn diag v P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [rpm]
Max
- [rpm]
Factory setting
- [rpm]
Description:
Displays the actual velocity values for the motion monitoring functions on processor 1.
Index:
[0] = Load-side velocity actual value on processor 1
[1] = Actual SAM/SBR velocity limit on processor 1
r9720.0...13
CO/BO: SI Motion control signals integrated in the drive / SI Mtn integ STW
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Control signals for safety-relevant motion monitoring functions integrated in the drive.
Bit field:
Bit
00
01
04
07
09
10
12
13
Note:
This parameter is only supplied with actual values if SI Motion functions are active. For Safety Integrated Basic
Functions (STO), the value is equal to zero.
1-364
Signal name
De-select STO
De-select SS1
De-select SLS
Acknowledgement
Select SLS bit 0
Select SLS bit 1
Deselect SDI positive
Deselect SDI negative
1 signal
Yes
Yes
Yes
Signal edge active
Set
Set
Yes
Yes
0 signal
No
No
No
No
Not set
Not set
No
No
FP
2861
2861
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9722.0...15
CO/BO: SI Motion status signals integrated in the drive / SI Mtn integ stat
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Status signal for safety-relevant motion monitoring functions integrated in the drive.
Bit field:
Bit
00
01
04
07
09
10
12
13
15
Notice:
Re bit 07:
Signal name
STO active
SS1 active
SLS active
Internal event
Active SLS stage bit 0
Active SLS stage bit 1
SDI pos active
SDI neg active
SSM (speed below limit value)
1 signal
Yes
Yes
Yes
No
Set
Set
Yes
Yes
Yes
0 signal
No
No
No
Yes
Not set
Not set
No
No
No
FP
2861
2861
2860
An internal event is displayed if a STOP A ... F is active.
The signal state behaves in an opposite way to the PROFIsafe Standard.
Note:
This parameter is only supplied with actual values if SI Motion functions are active. For Safety Integrated Basic
Functions (STO), the value is equal to zero.
r9722.0...13
CO/BO: SI Motion status signals integrated in the drive / SI Mtn integ stat
CU240E-2 F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Status signal for safety-relevant motion monitoring functions integrated in the drive.
Bit field:
Bit
00
01
04
07
09
10
12
13
Notice:
Re bit 07:
Signal name
STO active
SS1 active
SLS active
Internal event
Active SLS stage bit 0
Active SLS stage bit 1
SDI pos active
SDI neg active
1 signal
Yes
Yes
Yes
No
Set
Set
Yes
Yes
0 signal
No
No
No
Yes
Not set
Not set
No
No
FP
2861
2861
An internal event is displayed if a STOP A ... F is active.
The signal state behaves in an opposite way to the PROFIsafe Standard.
Note:
This parameter is only supplied with actual values if SI Motion functions are active. For Safety Integrated Basic
Functions (STO), the value is equal to zero.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-365
Parameters
List of Parameters
r9723.0...16
CO/BO: SI Motion diagnostic signals integrated in the drive / SI Mtn integ diag
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the diagnostic signals for safety-relevant motion monitoring functions integrated in the drive.
Bit field:
Bit
00
01
02
03
04
16
Signal name
Forced checking procedure required
For ESR, STOP F and subsequent stop B is
active
Communication failure
Actual value sensing supplies valid value
Encoderless act val sensing acc to technique for U/f control
SAM/SBR active
1 signal
Yes
Yes
0 signal
No
No
FP
-
Yes
Yes
Yes
No
No
No
-
Yes
No
-
Note:
ESR: Extended Stop and Retract
SAM: Safe Acceleration Monitor (safe acceleration monitoring)
SBR: Safe Brake Ramp (safe brake ramp monitoring)
r9724
SI Motion crosswise comparison clock cycle / SI Mtn CDC clk cyc
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Description:
Factory setting
- [ms]
Note:
Displays the crosswise comparison clock cycle.
The value indicates the clock cycle time with which each individual CDC value is compared between the two monitoring channels.
CDC: Crosswise Data Check
r9725[0...2]
SI Motion, diagnostics STOP F / SI Mtn Diag STOP F
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Index:
Dependency:
Note:
1-366
Factory setting
-
Re index 0:
Displays the message value that resulted in the STOP F on the drive.
Value = 0:
Processor 1 signaled a STOP F.
Value = 1 ... 999:
Number of the incorrect date in the crosswise data comparison between the monitoring channels.
Value >= 1000:
Additional diagnostic values of the drive.
Re index 1:
Displays the value from processor 1 that resulted in the STOP F.
Re index 2:
Displays the value from processor 2 that resulted in the STOP F.
[0] = Message value for CDC
[1] = Processor 1 CDC actual value
[2] = Processor 2 CDC actual value
Refer to: C01711
The significance of the individual message values is described in message C01711.
CDC: Crosswise Data Check
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9728[0...2]
SI Motion actual checksum SI parameters (processor 1) / SI Mtn act CRC P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the checksum over the checked Safety Integrated parameters of the motion monitoring functions (actual
checksum).
Index:
[0] = Checksum over SI parameters for motion monitoring
[1] = Checksum over SI parameters for actual values
[2] = Checksum over SI parameters for hardware
Dependency:
Refer to: p9729
Refer to: F01680
p9729[0...2]
SI Motion setpoint checksum SI parameters (processor 1) / SI Mtn setp CRC P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
Factory setting
0000 hex
Description:
Sets the checksum using the checksum-tested Safety Integrated parameters for motion monitoring functions (reference checksum).
Index:
[0] = Checksum over SI parameters for motion monitoring
[1] = Checksum over SI parameters for actual values
[2] = Checksum over SI parameters for hardware
Dependency:
Refer to: r9728
Refer to: F01680
r9732
SI Motion velocity resolution / SI Mtn v_res
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP F
Can be changed: -
Scaling: -
Data set: -
CU240E-2 F
Units group: -
Unit selection: -
Min
- [rpm]
Max
- [rpm]
Description:
Factory setting
- [rpm]
Displays the safe velocity resolution (load side).
Setpoints for velocity limits or parameter changes for velocities below this threshold have no effect.
Note:
This parameter does not provide any information about the actual accuracy of the velocity sensing. This depends
on the type of actual value sensing, the gear factors as well as the quality of the encoder being used.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-367
Parameters
List of Parameters
r9733[0...2]
CO: SI Motion setpoint speed limit effective / SI Mtn setp_lim
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: -
Scaling: p2000
Data set: -
Units group: 3_1
Unit selection: p0505
Min
- [rpm]
Max
- [rpm]
Description:
Factory setting
- [rpm]
Displays the necessary setpoint speed limit as a result of the selected motion monitoring functions.
Contrary to the parameterization of the SI limit values, this parameter specifies the motor-side limit value and not
the load-side limit value.
Index:
[0] = Setpoint limiting positive
[1] = Setpoint limiting negative
[2] = Setpoint limit absolute
Dependency:
For SLS: r9733[0] = p9531[x] x p9533 (converted from the load side to the motor side)
For SDI negative: r9733[0] = 0
For SLS: r9733[1] = - p9531[x] x p9533 (converted from the load side to the motor side)
For SDI positive: r9733[1] = 0
[x] = Selected SLS stage
Conversion factor from the motor side to the load side:
- motor type = rotary and axis type = linear: p9522 / (p9521 x p9520)
- otherwise: p9522 / p9521
Refer to: p9531, p9533
Notice:
If p1051 = r9733[0] is interconnected, p1052 = r9733[1] must also be interconnected.
If only the absolute value of the setpoint velocity limiting is required, r9733[2] must be interconnected.
Note:
If the "SLS" function is not selected, r9733[0] shows p1082 and r9733[1] shows -p1082.
The display in r9733 can be delayed by up to one Safety monitoring clock cycle as compared to the display in r9720
and r9722.
r9734.0...14
CO/BO: SI Motion Safety Info Channel status word / SI Mtn info ch ZSW
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the status word for the Safety information channel.
Bit field:
Bit
00
01
04
06
07
12
13
14
Notice:
Re bit 07:
Signal name
STO active
SS1 active
SLS active
SLS selected
Internal event
SDI positive selected
SDI neg selected
ESR retract requested
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
No
FP
-
An internal event is displayed if a STOP A ... F is active.
The signal state behaves in an opposite way to the PROFIsafe Standard.
Note:
1-368
This parameter is only supplied with actual values if SI Motion functions are active. For Safety Integrated Basic
Functions (STO), the value is equal to zero.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9742.0...15
CO/BO: SI Motion drive-integrated status signals (processor 2) / SI Mtn int stat P2
CU240E-2 DP F
Access level: 4
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Status signal for safety-relevant motion monitoring functions integrated in the drive.
Bit field:
Bit
00
01
04
07
09
10
15
Notice:
Re bit 07:
Signal name
STO active
SS1 active
SLS active
Internal event
Active SLS stage bit 0
Active SLS stage bit 1
SSM (speed below limit value)
1 signal
Yes
Yes
Yes
No
Set
Set
Yes
0 signal
No
No
No
Yes
Not set
Not set
No
FP
2860
An internal event is displayed if a STOP A ... F is active.
The signal state behaves in an opposite way to the PROFIsafe Standard.
Note:
This parameter is only supplied with actual values if SI Motion functions are active. For Safety Integrated Basic
Functions (STO), the value is equal to zero.
p9761
SI password input / SI password inp
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: C, T
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
CU240E-2 F
Factory setting
0000 hex
Description:
Enters the Safety Integrated password.
Dependency:
Refer to: F01659
Note:
It is not possible to change Safety Integrated parameters until the Safety Integrated password has been entered.
p9762
SI password new / SI password new
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
CU240E-2 F
Factory setting
0000 hex
Description:
Enters a new Safety Integrated password.
Dependency:
A change made to the Safety Integrated password must be acknowledged in the following parameter:
Refer to: p9763
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-369
Parameters
List of Parameters
p9763
SI password acknowledgement / SI ackn password
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
CU240E-2 F
Factory setting
0000 hex
Description:
Dependency:
Note:
Acknowledges the new Safety Integrated password.
Refer to: p9762
The new password entered into p9762 must be re-entered in order to acknowledge.
p9762 = p9763 = 0 is automatically set after the new Safety Integrated password has been successfully acknowledged.
r9765
SI Motion forced checking procedure remaining time (processor 1) /
SI Mtn dyn rem P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [h]
Max
- [h]
Description:
Dependency:
Factory setting
- [h]
Displays the time remaining until the next dynamization and testing of the safety motion monitoring functions integrated in the drives.
The signal source to initiate the forced checking procedure is parameterized in p9705.
Refer to: p9705
Refer to: C01798
r9770[0...3]
SI version drive-integrated safety function (processor 1) / SI version Drv P1
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Index:
Note:
Factory setting
-
Displays the Safety Integrated version for the drive-integrated safety functions on processor 1.
[0] = Safety Version (major release)
[1] = Safety Version (minor release)
[2] = Safety Version (baselevel or patch)
[3] = Safety Version (hotfix)
Example:
r9770[0] = 2, r9770[1] = 60, r9770[2] = 1, r9770[3] = 0 --> Safety version V02.60.01.00
r9771
SI common functions (processor 1) / SI general fct P1
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 1 determines this display.
Bit field:
Bit
00
Dependency:
Refer to: r9871
Note:
STO: Safe Torque Off
1-370
Signal name
STO supported via terminals
1 signal
Yes
0 signal
No
FP
2804
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9771
SI common functions (processor 1) / SI general fct P1
CU240E-2 DP
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 1 determines this display.
Bit field:
Bit
00
06
Dependency:
Refer to: r9871
Note:
STO: Safe Torque Off
r9771
SI common functions (processor 1) / SI general fct P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Signal name
STO supported via terminals
Basic Functions PROFIsafe supported
1 signal
Yes
Yes
0 signal
No
No
FP
2804
-
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 1 determines this display.
Bit field:
Bit
00
02
04
05
06
07
11
12
Signal name
STO supported via terminals
Extended Functions supported (p9501 > 0)
Extended Functions PROFIsafe supported
Extended Functions integrated in drive supported (p9601.2 = 1)
Basic Functions PROFIsafe supported
Extended Functions encoderless supported
Extended Functions SDI supported
Extended Functions SSM encoderless supported
1 signal
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
FP
2804
2804
-
Yes
Yes
Yes
Yes
No
No
No
No
-
Dependency:
Refer to: r9871
Note:
STO: Safe Torque Off
r9771
SI common functions (processor 1) / SI general fct P1
CU240E-2 F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 1 determines this display.
Bit field:
Bit
00
02
05
07
11
12
Signal name
STO supported via terminals
Extended Functions supported (p9501 > 0)
Extended Functions integrated in drive supported (p9601.2 = 1)
Extended Functions encoderless supported
Extended Functions SDI supported
Extended Functions SSM encoderless supported
Dependency:
Refer to: r9871
Note:
STO: Safe Torque Off
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
2804
2804
-
Yes
Yes
Yes
No
No
No
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-371
Parameters
List of Parameters
r9772.0...20
CO/BO: SI status (processor 1) / SI status P1
CU240E-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the Safety Integrated status on processor 1.
Bit field:
Bit
00
01
09
10
15
16
17
18
19
20
Signal name
STO selected on processor 1
STO active on processor 1
STOP A cannot be acknowledged, active
STOP A active
STOP F active
STO cse: Safety comm. mode
STO cause selection via terminal (Basic
Functions)
STO cause: Selection via motion monitoring
functions
STO cause actual value missing
STO cause selection PROFIsafe (Basic
Functions)
Dependency:
Refer to: r9872
Note:
Re bit 00:
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
FP
2810
2810
2802
2802
2802
-
Yes
No
-
Yes
Yes
No
No
-
When STO is selected, the cause is displayed in bits 16 ... 20.
Re bit 18:
When the bit is set, STO is selected via PROFIsafe.
Re bit 19:
For the drive-integrated motion monitoring functions, due to OFF2, no actual value sensing possible.
r9773.0...31
CO/BO: SI status (processor 1 + processor 2) / SI status P1+P2
CU240E-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the Safety Integrated status on the drive (processor 1 + processor 2).
Bit field:
Bit
00
01
31
Note:
This status is formed from the AND operation of the relevant status of the two monitoring channels.
1-372
Signal name
STO selected in drive
STO active in drive
Shutdown paths must be tested
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
2804
2804
2810
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9776
SI diagnostics / SI diagnostics
CU240E-2
Access level: 4
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
The parameter is used for diagnostics.
Bit field:
Bit
00
Note:
Re bit 00 = 1:
Signal name
Safety parameter changed POWER ON
required
Factory setting
1 signal
Yes
0 signal
No
FP
-
At least one Safety parameter has been changed that will only take effect after a POWER ON.
r9780
SI monitoring clock cycle (processor 1) / SI mon_clk cyc P1
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
CU240E-2 F
Description:
Factory setting
- [ms]
Displays the clock cycle time for the Safety Integrated Basic Functions on processor 1.
r9781[0...1]
SI checksum to check changes (processor 1) / SI chg chksm P1
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
-
Displays the checksum for tracking changes for Safety Integrated.
These are additional checksums that are created to track changes (fingerprint for the "safety logbook" functionality)
to safety parameters (that are relevant for checksums).
Index:
[0] = SI checksum to track functional changes
[1] = SI checksum to track hardware-specific changes
Dependency:
Refer to: p9601, p9729, p9799
Refer to: F01690
r9782[0...1]
SI time stamp to check changes (processor 1) / SI chg t P1
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
- [h]
Max
- [h]
CU240E-2 F
Description:
Factory setting
- [h]
Displays the time stamps for the checksums for tracking changes for Safety Integrated.
The time stamps for the checksums for tracking changes (fingerprint for the "safety logbook" functionality) made to
safety parameters are saved in parameters p9781[0] and p9781[1].
Index:
[0] = SI time stamp for checksum to track functional changes
[1] = SI time stamp for checksum to track hardware-specific changes
Dependency:
Refer to: p9601, p9729, p9799
Refer to: F01690
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-373
Parameters
List of Parameters
r9794[0...19]
SI crosswise comparison list (processor 1) / SI CDC_list P1
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
-
Displays the numbers of the data items that are currently being compared crosswise on processor 1.
The content of the list of crosswise-compared data is dependent upon the particular application.
Note:
Example:
r9794[0] = 1 (monitoring clock cycle)
r9794[1] = 2 (enable safety functions)
r9794[2] = 3 (F-DI changeover, tolerance time)
...
A complete list of numbers for crosswise-compared data items appears in fault F01611.
r9795
SI diagnostics STOP F (processor 1) / SI diag STOP F P1
CU240E-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the number of the cross-checked data item which caused STOP F on processor 1.
Dependency:
Refer to: F01611
Note:
A complete list of numbers for crosswise-compared data items appears in fault F01611.
r9798
SI actual checksum SI parameters (processor 1) / SI act chksm P1
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the checksum for the Safety Integrated parameters checked using checksums on processor 1 (actual
checksum).
Dependency:
Refer to: p9799, r9898
p9799
SI setpoint checksum SI parameters (processor 1) / SI setp_chksm P1
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
CU240E-2 F
Factory setting
0000 hex
Description:
Sets the checksum for the Safety Integrated parameters checked using checksums on processor 1 (setpoint checksum).
Dependency:
Refer to: r9798, p9899
1-374
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9801
SI enable, functions integrated in the drive (processor 2) / SI enable fct P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned16
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2
Description:
Factory setting
0000 bin
Sets the enable signals for safety functions on processor 2 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9801 = 0: Safety functions integrated in the drive disabled.
- p9801 = 1: STO enabled via terminals. Permissible if r9871.0 = 1.
- p9801 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9871.5 = 1.
- p9801 = 8: STO enabled via PROFIsafe. Permissible if r9871.6 = 1.
- p9801 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9871.6 = 1.
- p9801 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9871.4 = 1.
- p9801 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9871.4 = 1.
Bit field:
Bit
00
Signal name
Enable STO via terminals (processor 2)
1 signal
Enable
0 signal
Inhibit
Dependency:
Refer to: p9601, r9871
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
A change only becomes effective after a POWER ON.
FP
2810
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
p9801
SI enable, functions integrated in the drive (processor 2) / SI enable fct P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned16
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP
Factory setting
0000 bin
Description:
Sets the enable signals for safety functions on processor 2 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9801 = 0: Safety functions integrated in the drive disabled.
- p9801 = 1: STO enabled via terminals. Permissible if r9871.0 = 1.
- p9801 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9871.5 = 1.
- p9801 = 8: STO enabled via PROFIsafe. Permissible if r9871.6 = 1.
- p9801 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9871.6 = 1.
- p9801 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9871.4 = 1.
- p9801 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9871.4 = 1.
Bit field:
Bit
00
03
Dependency:
Notice:
Note:
Refer to: p9601, r9871
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
A change only becomes effective after a POWER ON.
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
Signal name
Enable STO via terminals (processor 2)
Enable PROFIsafe (processor 2)
1 signal
Enable
Enable
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
Inhibit
Inhibit
FP
2810
-
1-375
Parameters
List of Parameters
p9801
SI enable, functions integrated in the drive (processor 2) / SI enable fct P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned16
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 DP F
Factory setting
0000 bin
Description:
Sets the enable signals for safety functions on processor 2 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9801 = 0: Safety functions integrated in the drive disabled.
- p9801 = 1: STO enabled via terminals. Permissible if r9871.0 = 1.
- p9801 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9871.5 = 1.
- p9801 = 8: STO enabled via PROFIsafe. Permissible if r9871.6 = 1.
- p9801 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9871.6 = 1.
- p9801 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9871.4 = 1.
- p9801 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9871.4 = 1.
Bit field:
Bit
00
02
Dependency:
Notice:
Note:
Refer to: p9601, r9871
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
A change only becomes effective after a POWER ON.
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
03
1-376
Signal name
Enable STO via terminals (processor 2)
Motion monitoring functions integr. in the
drive (processor 2)
Enable PROFIsafe (processor 2)
1 signal
Enable
Enable
0 signal
Inhibit
Inhibit
FP
2810
-
Enable
Inhibit
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p9801
SI enable, functions integrated in the drive (processor 2) / SI enable fct P2
PM240
Access level: 3
Calculated: -
Data type: Unsigned16
PM250
Can be changed: C(95)
Scaling: -
Data set: -
PM260
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Description:
Factory setting
0000 bin
Sets the enable signals for safety functions on processor 2 that are integrated in the drive.
Not all of the settings listed below will be permissible, depending on the Control Unit being used:
- p9801 = 0: Safety functions integrated in the drive disabled.
- p9801 = 1: STO enabled via terminals. Permissible if r9871.0 = 1.
- p9801 = 4: Motion monitoring functions integrated in the drive enabled via an integrated F-DI. Permissible if
r9871.5 = 1.
- p9801 = 8: STO enabled via PROFIsafe. Permissible if r9871.6 = 1.
- p9801 = 9: STO enabled via PROFIsafe and STO via terminals. Permissible if r9871.6 = 1.
- p9801 = 12: Motion monitoring functions integrated in the drive enabled via PROFIsafe. Permissible if r9871.4 = 1.
- p9801 = 13: Motion monitoring functions integrated in the drive enabled via PROFIsafe and STO via terminals.
Permissible if r9871.4 = 1.
Bit field:
Bit
00
02
Signal name
Enable STO via terminals (processor 2)
Motion monitoring functions integr. in the
drive (processor 2)
1 signal
Enable
Enable
0 signal
Inhibit
Inhibit
Dependency:
Refer to: p9601, r9871
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
A change only becomes effective after a POWER ON.
FP
2810
-
F-DI: Failsafe Digital Input.
STO: Safe Torque Off
p9810
SI PROFIsafe address (processor 2) / SI PROFIsafe P2
CU240E-2 DP
Access level: 3
Calculated: -
Data type: Unsigned16
CU240E-2 DP F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFE hex
Factory setting
0000 hex
Description:
Sets the PROFIsafe address on processor 2.
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
p9850
SI F-DI changeover tolerance time (processor 2) / SI F-DI_chg tol P2
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
2000000.00 [µs]
CU240E-2 F
Description:
Dependency:
Notice:
Note:
Factory setting
500000.00 [µs]
Sets the tolerance time for the changeover of the failsafe digital input for STO on processor 2.
An F-DI changeover is not effective simultaneously due to the different runtimes in the two monitoring channels.
After an F-DI changeover, dynamic data is not subject to a crosswise data comparison during this tolerance time.
Refer to: p9650
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
For a crosswise data comparison between p9650 and p9850, a difference of one Safety monitoring clock cycle is
tolerated.
The parameterized time is internally rounded-off to an integer multiple of the monitoring clock cycle.
F-DI: Failsafe Digital Input
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-377
Parameters
List of Parameters
p9851
SI STO debounce time (processor 2) / SI STO t_debou P2
CU240E-2
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0.00 [µs]
Max
100000.00 [µs]
CU240E-2 F
Description:
Factory setting
0.00 [µs]
Sets the debounce time for the failsafe digital inputs used to control the "STO" function.
The debounce time is rounded to whole milliseconds.
Dependency:
Refer to: p9651
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
The debounce time is rounded to whole milliseconds. It specifies the maximum duration of a fault pulse at the failsafe digital inputs with no reaction/influence on the selection or deselection of the Safety Basic Functions.
Example:
Debounce time = 1 ms: Fault pulses of 1 ms are filtered; only pulses longer than 2 ms are processed.
Debounce time = 3 ms: Fault pulses of 3 ms are filtered; only pulses longer than 4 ms are processed.
r9871
SI common functions (processor 2) / SI common fct P2
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 2 determines this display.
Bit field:
Bit
00
Dependency:
Refer to: r9771
Note:
STO: Safe Torque Off
r9871
SI common functions (processor 2) / SI common fct P2
CU240E-2 DP
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Signal name
STO supported via terminals
1 signal
Yes
0 signal
No
FP
2804
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 2 determines this display.
Bit field:
Bit
00
06
Dependency:
Refer to: r9771
Note:
STO: Safe Torque Off
1-378
Signal name
STO supported via terminals
Basic Functions PROFIsafe supported
1 signal
Yes
Yes
0 signal
No
No
FP
2804
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9871
SI common functions (processor 2) / SI common fct P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 2 determines this display.
Bit field:
Bit
00
02
04
05
06
07
11
12
Signal name
STO supported via terminals
Extended Functions supported (p9501 > 0)
Extended Functions PROFIsafe supported
Extended Functions integrated in drive supported (p9601.2 = 1)
Basic Functions PROFIsafe supported
Extended Functions encoderless supported
Extended Functions SDI supported
Extended Functions SSM encoderless supported
1 signal
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
FP
2804
2804
-
Yes
Yes
Yes
Yes
No
No
No
No
-
Dependency:
Refer to: r9771
Note:
STO: Safe Torque Off
r9871
SI common functions (processor 2) / SI common fct P2
CU240E-2 F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the supported Safety Integrated monitoring functions.
Processor 2 determines this display.
Bit field:
Bit
00
02
05
07
11
12
Signal name
STO supported via terminals
Extended Functions supported (p9501 > 0)
Extended Functions integrated in drive supported (p9601.2 = 1)
Extended Functions encoderless supported
Extended Functions SDI supported
Extended Functions SSM encoderless supported
Dependency:
Refer to: r9771
Note:
STO: Safe Torque Off
1 signal
Yes
Yes
Yes
0 signal
No
No
No
FP
2804
2804
-
Yes
Yes
Yes
No
No
No
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-379
Parameters
List of Parameters
r9872.0...20
CO/BO: SI status (processor 2) / SI Status P2
CU240E-2
Access level: 2
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the Safety Integrated status on processor 2.
Bit field:
Bit
00
01
09
10
15
16
17
18
20
Signal name
STO selected on processor 2
STO active on processor 2
STOP A cannot be acknowledged, active
STOP A active
STOP F active
STO cse: Safety comm. mode
STO cause selection via terminal (Basic
Functions)
STO cause: Selection via motion monitoring
functions
STO cause selection PROFIsafe (Basic
Functions)
Dependency:
Refer to: r9772
Note:
Re bit 00:
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0 signal
No
No
No
No
No
No
No
FP
2810
2810
2802
2802
2802
-
Yes
No
-
Yes
No
-
When STO is selected, the cause is displayed in bits 16 ... 20.
Re bit 18:
When the bit is set, STO is selected via PROFIsafe.
r9898
SI actual checksum SI parameters (processor 2) / SI act_chksm P2
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: -
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
-
Max
-
CU240E-2 F
Factory setting
-
Description:
Displays the checksum for the Safety Integrated parameters checked using checksums on processor 2 (actual
checksum).
Dependency:
Refer to: r9798, p9899
p9899
SI setpoint checksum SI parameters (processor 2) / SI setp_chksm P2
CU240E-2
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 DP
Can be changed: C(95)
Scaling: -
Data set: -
CU240E-2 DP F
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
CU240E-2 F
Factory setting
0000 hex
Description:
Sets the checksum for the Safety Integrated parameters checked using checksums on processor 2 (setpoint checksum).
Dependency:
Refer to: p9799, r9898
1-380
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9925[0...99]
Firmware file incorrect / FW file incorr
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Displays the directory and name of the file whose status as shipped from the factory was identified as impermissible.
Dependency:
Refer to: r9926
Refer to: A01016
Note:
The directory and name of the file is displayed in the ASCII code.
r9926
Firmware check status / FW check status
Description:
Access level: 3
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Displays the status when the firmware is checked when the system is booted.
0: Firmware not yet checked.
1: Check running.
2: Check successfully completed.
3: Check indicates an error.
Dependency:
Refer to: r9925
Refer to: A01016
p9930[0...8]
System logbook activation / SYSLOG activation
Access level: 4
Calculated: -
Data type: Unsigned8
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Factory setting
0
Description:
Only for service purposes.
Index:
[0] = System logbook stage (0: Not active)
[1] = COM2/COM1 (0: COM2, 1: COM1)
[2] = Activate file write (0: Not active)
[3] = Display time stamp (0: Not displayed)
[4] = Reserved
[5] = Reserved
[6] = Reserved
[7] = Reserved
[8] = System logbook file size (stages, each 10 kB)
Notice:
Before powering down the Control Unit, ensure that the system logbook is switched out (p9930[0] = 0).
If writing to the file is activated (p9930[2] = 1), writing to the file must be de-activated again before switching off the
Control Unit (p9930[2] = 0) in order to ensure that the system logbook has been completely written to the file.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-381
Parameters
List of Parameters
p9931[0...129]
System logbook module selection / SYSLOG mod select.
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0000 hex
Max
FFFF FFFF hex
Description:
Only for service purposes.
p9932
Save system logbook EEPROM / SYSLOG EEPROM save
Factory setting
0000 hex
Access level: 4
Calculated: -
Data type: Unsigned8
Can be changed: U, T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Factory setting
0
Description:
Only for service purposes.
r9935.0
BO: POWER ON delay signal / POWER ON t_delay
Access level: 4
Calculated: -
Data type: Unsigned8
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
After power-on, binector output r9935.0 is set with the start of the first sampling time and is again reset after approx.
100 ms.
Bit field:
Bit
00
r9975[0...7]
System utilization measured / Sys util meas
Signal name
POWER ON delay signal
1 signal
High
0 signal
Low
Access level: 4
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Description:
Displays the measured system utilization.
Index:
[0] = Computing time utilization (min)
[1] = Computing time utilization (averaged)
[2] = Computing time utilization (max)
[3] = Largest total utilization (min)
[4] = Largest total utilization (averaged)
[5] = Largest total utilization (max)
[6] = Reserved
[7] = Reserved
Dependency:
Refer to: r9976
FP
-
Factory setting
- [%]
The higher the value displayed, the higher the system utilization.
Refer to: F01205
Note:
Re index 3 ... 5:
The total utilizations are determined using all sampling times used. The largest total utilizations are mapped here.
The sampling time with the largest total utilization is displayed in r9979.
Total utilization:
Computing time load of sampling time involved including load from higher-priority sampling times (interrupts).
1-382
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r9976[0...7]
Description:
System utilization / Sys util
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [%]
Max
- [%]
Factory setting
- [%]
Displays the system utilization.
If the utilization is greater than 100%, fault F01054 is output.
Index:
[0] = Reserved
[1] = Computing time utilization
[2] = Reserved
[3] = Reserved
[4] = Reserved
[5] = Largest total utilization
[6] = Reserved
[7] = Reserved
Dependency:
Refer to: F01205
Note:
Re index 1:
The value shows the total computing time load of the system.
Re index 5:
The total utilization is determined using all sampling times used. The largest total utilization is mapped here. The
sampling time with the largest total utilization is displayed in r9979.
Total utilization:
Computing time load of sampling time involved including load from higher-priority sampling times (interrupts).
r9999[0...99]
Software error internal supplementary diagnostics / SW_err int diag
Access level: 4
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Diagnostics parameter to display additional information for internal software errors.
Note:
Only for internal Siemens troubleshooting.
p10002
SI discrepancy monitoring time (processor 1) / SI discrp t_mon P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1.00 [ms]
Max
2000.00 [ms]
Description:
Factory setting
500.00 [ms]
Sets the monitoring time for the discrepancy for the digital inputs.
The signal states at the two associated digital inputs (F-DI) must assume the same state within this monitoring time.
Dependency:
Refer to: p10102
Note:
F-DI: Failsafe Digital Input
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-383
Parameters
List of Parameters
p10006
SI acknowledgement internal event F-DI (processor 1) / SI ackn int evt P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Factory setting
0
Select a safety-relevant digital input for the signal "acknowledge internal event" (internal fault).
The falling edge at this input resets the status "internal event" in the drive.
Value:
0:
1:
2:
3:
255:
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
Dependency:
Refer to: p10106
Refer to: A01666, A30666
Note:
F-DI: Failsafe Digital Input
If value = 0:
No terminal assigned, acknowledge input has a static zero value.
p10017
SI digital inputs debounce time (processor 1) / SI DI t_debounceP1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
100.00 [ms]
Description:
Factory setting
1.00 [ms]
Sets the debounce time for digital inputs.
The debounce time is accepted rounded off to whole milliseconds.
The debounce time acts on the following digital inputs:
- Fail-safe digital inputs (F-DI).
- Single-channel digital inputs (DI).
- Single-channel digital input 2 (DI 2, read back input for the forced checking procedure).
Dependency:
Refer to: p10117
Note:
Example:
Debounce time = 1 ms: Fault pulses of 1 ms are filtered; only pulses longer than 2 ms are processed.
Debounce time = 3 ms: Fault pulses of 3 ms are filtered; only pulses longer than 4 ms are processed.
The debounce result can be read in r10051.
1-384
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p10022
SI STO input terminal (processor 1) / SI STO F-DI P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Sets the fail-safe digital input (F-DI) for the "STO" function.
Value:
0:
1:
2:
3:
255:
Dependency:
Refer to: p10122
Note:
If value = 0:
Factory setting
0
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
STO: Safe Torque Off
p10023
SI SS1 input terminal (processor 1) / SI SS1 F-DI P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Sets the fail-safe digital input (F-DI) for the "SS1" function.
Value:
0:
1:
2:
3:
255:
Dependency:
Refer to: p10123
Note:
If value = 0:
Factory setting
0
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SS1: Safe Stop 1
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-385
Parameters
List of Parameters
p10026
SI SLS input terminal (processor 1) / SI SLS F-DI P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Value:
Factory setting
0
Dependency:
Note:
Sets the fail-safe digital input (F-DI) for the "SLS" function.
0:
Statically active
1:
F-DI 0
2:
F-DI 1
3:
F-DI 2
255: Statically inact
Refer to: p10126
If value = 0:
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SLS: Safely-Limited Speed
p10030
SI SDI positive input terminal (processor 1) / SI SDI pos F-DI P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Value:
Factory setting
0
Note:
Sets the fail-safe digital input (F-DI) for the "SDI positive" function.
0:
Statically active
1:
F-DI 0
2:
F-DI 1
3:
F-DI 2
255: Statically inact
If value = 0:
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
p10031
SI SDI negative input terminal (processor 1) / SI SDI neg F-DI P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Value:
Note:
1-386
Factory setting
0
Sets the fail-safe digital input (F-DI) for the "SDI negative" function.
0:
Statically active
1:
F-DI 0
2:
F-DI 1
3:
F-DI 2
255: Statically inact
If value = 0:
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r10049
SI F-DI monitoring status (processor 1) / SI F-DI status P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the monitoring status of the fail-safe digital inputs (F-DI).
The F-DIs that are being used by the Safety Integrated functions are displayed.
If the module used has fewer than 3 F-DIs, "Freely available" is displayed for the F-DIs which are not in use.
Bit field:
Bit
00
01
02
Signal name
F-DI 0
F-DI 1
F-DI 2
Dependency:
p10006 / p10106
1 signal
Safety monitored
Safety monitored
Safety monitored
0 signal
Freely available
Freely available
Freely available
FP
-
p10022 / p10122
p10023 / p10123
p10026 / p10126
p10030 / p10130
p10031 / p10131
p10050 / p10150
Refer to: r10149
p10050
SI PROFIsafe F-DI transfer (processor 1) / SI Ps F-DI tran P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
0000 bin
Setting for the transfer and evaluation of failsafe digital inputs (F-DI) via PROFIsafe.
The safe state of the selected F-DIs is transferred to the F-control via PROFIsafe. The F-DIs are monitored for discrepancies. Discrepancy faults can be acknowledged via PROFIsafe.
Bit field:
Bit
00
01
02
Signal name
F-DI 0
F-DI 1
F-DI 2
Dependency:
Refer to: p10150
Note:
F-DI: Failsafe Digital Input
1 signal
Transfer
Transfer
Transfer
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
0 signal
No transfer
No transfer
No transfer
FP
-
1-387
Parameters
List of Parameters
r10051.0...2
CO/BO: SI digital inputs status (processor 1) / SI DI status P1
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the single-channel, logical, and debounced status of the fail-safe digital inputs (F-DI).
The parameter is updated in the SI Motion monitoring clock cycle.
Bit field:
Bit
00
01
02
Signal name
F-DI 0
F-DI 1
F-DI 2
1 signal
High
High
High
0 signal
Low
Low
Low
Dependency:
Refer to: p9501, p9601, p10017, p10050, r10151
Note:
If a safety function is assigned to an input (e.g. via p10022), then the following applies:
FP
-
- logical "0": Safety function is selected
- logical "1": Safety function is de-selected
The interrelationship between the logical level and the external voltage level at the input depends on the parameterization (refer to p10040) of the input as either NC or NO contact and is aligned to the use of a safety function:
With 24 V at the input, NC contacts have a logical "1" level, for 0 V at the input, a logical "0" level.
This means that an NC/NC contact parameterization of 0 V at both inputs of the F-DI selects the safety function, for
24 V at both inputs, de-selects the safety function.
With 24 V at the input, NO contacts have a logical "0" level, for 0 V at the input, a logical "1" level.
This means that for an NC/NO contact parameterization, the level 0 V/24 V selects the safety function, the level 24
V/0 V de-selects the safety function.
F-DI: Failsafe Digital Input
The state of parameter r10151 is delayed by one monitoring clock cycle in relation to r10051.
The parameter is only updated in the following cases:
- If the Safety Extended Functions are enabled by means of activation via F-DI.
- If transfer of the F-DIs via PROFIsafe is enabled (see p9501).
In this case only the F-DIs transferred for PROFIsafe are displayed and updated (see p10050/p10150). All F-DIs
which have not been transferred have a static zero value.
p10102
SI discrepancy monitoring time (processor 2) / SI discr t_mon P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1.00 [ms]
Max
2000.00 [ms]
Description:
Factory setting
500.00 [ms]
Sets the monitoring time for the discrepancy for the digital inputs.
The signal states at the two associated digital inputs (F-DI) must assume the same state within this monitoring time.
Dependency:
Refer to: p10002
Note:
F-DI: Failsafe Digital Input
1-388
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p10106
SI acknowledgement internal event F-DI (processor 2) / SI ackn int evt P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Factory setting
0
Select a safety-relevant digital input for the signal "acknowledge internal event" (internal fault).
The falling edge at this input resets the status "internal event" in the drive.
Value:
0:
1:
2:
3:
255:
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
Dependency:
Refer to: p10006
Note:
If value = 0:
No terminal assigned, acknowledge input has a static zero value.
p10117
SI digital inputs debounce time (processor 2) / SI DI t_debounceP2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: FloatingPoint32
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00 [ms]
Max
100.00 [ms]
Description:
Factory setting
1.00 [ms]
Sets the debounce time for digital inputs.
The debounce time acts on the following digital inputs:
- Fail-safe digital inputs (F-DI).
- Single-channel digital input 2 (DI 2, read back input for the forced checking procedure).
The debounce time is accepted rounded off to whole milliseconds.
Dependency:
Refer to: p10017
Note:
Example:
Debounce time = 1 ms: Fault pulses of 1 ms are filtered; only pulses longer than 2 ms are processed.
Debounce time = 3 ms: Fault pulses of 3 ms are filtered; only pulses longer than 4 ms are processed.
The debounce result can be read in r10151.
p10122
SI STO input terminal (processor 2) / SI STO F-DI P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Value:
Dependency:
Note:
Factory setting
0
Sets the fail-safe digital input (F-DI) for the "STO" function.
0:
Statically active
1:
F-DI 0
2:
F-DI 1
3:
F-DI 2
255: Statically inact
Refer to: p10022
If value = 0:
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
STO: Safe Torque Off
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-389
Parameters
List of Parameters
p10123
SI SS1 input terminal (processor 2) / SI SS1 F-DI P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Sets the fail-safe digital input (F-DI) for the "SS1" function.
Value:
0:
1:
2:
3:
255:
Dependency:
Refer to: p10023
Note:
If value = 0:
Factory setting
0
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SS1: Safe Stop 1
p10126
SI SLS input terminal (processor 2) / SI SLS F-DI P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Sets the fail-safe digital input (F-DI) for the "SLS" function.
Value:
0:
1:
2:
3:
255:
Dependency:
Refer to: p10026
Note:
If value = 0:
Factory setting
0
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SLS: Safely-Limited Speed
1-390
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p10130
SI SDI positive input terminal (processor 2) / SI SDI pos DI P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Sets the fail-safe digital input (F-DI) for the "SDI positive" function.
Value:
0:
1:
2:
3:
255:
Note:
If value = 0:
Factory setting
0
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
p10131
SI SDI negative input terminal (processor 2) / SI SDI neg DI P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Integer16
CU240E-2 F
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
255
Description:
Sets the fail-safe digital input (F-DI) for the "SDI negative" function.
Value:
0:
1:
2:
3:
255:
Note:
If value = 0:
Factory setting
0
Statically active
F-DI 0
F-DI 1
F-DI 2
Statically inact
No terminal assigned, safety function always active.
If value = 255:
No terminal assigned, safety function always inactive.
F-DI: Failsafe Digital Input
SDI: Safe Direction (safe motion direction)
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-391
Parameters
List of Parameters
r10149
SI F-DI monitoring status (processor 2) / SI F-DI status P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the monitoring status of the fail-safe digital inputs (F-DI).
The F-DIs that are being used by the Safety Integrated functions are displayed.
If the module used has fewer than 3 F-DIs, "Freely available" is displayed for the F-DIs which are not in use.
Bit field:
Bit
00
01
02
Signal name
F-DI 0
F-DI 1
F-DI 2
Dependency:
p10006 / p10106
1 signal
Safety monitored
Safety monitored
Safety monitored
0 signal
Freely available
Freely available
Freely available
FP
-
p10022 / p10122
p10023 / p10123
p10026 / p10126
p10030 / p10130
p10031 / p10131
p10050 / p10150
Refer to: r10049
p10150
SI PROFIsafe F-DI transfer (processor 2) / SI Ps F-DI tran P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: C(95)
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
0000 bin
Setting for the transfer and evaluation of failsafe digital inputs (F-DI) via PROFIsafe.
The safe state of the selected F-DIs is transferred to the F-control via PROFIsafe. The F-DIs are monitored for discrepancies. Discrepancy faults can be acknowledged via PROFIsafe.
Bit field:
Bit
00
01
02
Dependency:
Refer to: p10050
Note:
F-DI: Failsafe Digital Input
1-392
Signal name
F-DI 0
F-DI 1
F-DI 2
1 signal
Transfer
Transfer
Transfer
0 signal
No transfer
No transfer
No transfer
FP
-
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r10151.0...2
CO/BO: SI digital inputs status (processor 2) / SI DI status P2
CU240E-2 DP F
Access level: 3
Calculated: -
Data type: Unsigned32
CU240E-2 F
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Factory setting
-
Displays the single-channel, logical, and debounced status of the fail-safe digital inputs (F-DI).
The parameter is updated in the SI Motion monitoring clock cycle.
Bit field:
Bit
00
01
02
Signal name
F-DI 0
F-DI 1
F-DI 2
1 signal
High
High
High
Dependency:
Refer to: p9501, p9601, p10117, p10150
Note:
F-DI: Failsafe Digital Input
0 signal
Low
Low
Low
FP
-
If a safety function is assigned to an input (e.g. via p10122), then the following applies:
- logical "0": Safety function is selected
- logical "1": Safety function is de-selected
The interrelationship between the logical level and the external voltage level at the input depends on the parameterization (refer to p10140) of the input as either NC or NO contact and is aligned to the use of a safety function:
With 24 V at the input, NC contacts have a logical "1" level, for 0 V at the input, a logical "0" level.
This means that an NC/NC contact parameterization of 0 V at both inputs of the F-DI selects the safety function, for
24 V at both inputs, de-selects the safety function.
With 24 V at the input, NO contacts have a logical "0" level, for 0 V at the input, a logical "1" level.
This means that for an NC/NO contact parameterization, the level 0 V/24 V selects the safety function, the level 24
V/0 V de-selects the safety function.
The state of parameter r10151 is delayed by one monitoring clock cycle in relation to r10051.
The parameter is only updated in the following cases:
- If the Safety Extended Functions are enabled by means of activation via F-DI.
- If transfer of the F-DIs via PROFIsafe is enabled (see p9501).
In this case only the F-DIs transferred for PROFIsafe are displayed and updated (see p10050/p10150). All F-DIs
which have not been transferred have a static zero value.
r20001[0...9]
Run-time group sampling time / RTG sampling time
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
- [ms]
Max
- [ms]
Description:
Displays the current sampling time of the run-time group 0 to 9.
Index:
[0] = Run-time group 0
[1] = Run-time group 1
[2] = Run-time group 2
[3] = Run-time group 3
[4] = Run-time group 4
[5] = Run-time group 5
[6] = Run-time group 6
[7] = Run-time group 7
[8] = Run-time group 8
[9] = Run-time group 9
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Factory setting
- [ms]
1-393
Parameters
List of Parameters
p20030[0...3]
BI: AND 0 inputs / AND 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance AND 0 of the AND function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20031
BO: AND 0 output Q / AND 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 & I1 & I2 & I3 of instance AND 0 of the AND function block.
p20032
AND 0 run-time group / AND 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance AND 0 of the AND function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20033
AND 0 run sequence / AND 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
10
Description:
Setting parameter for the run sequence of instance AND 0 within the run-time group set in p20032.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-394
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20034[0...3]
BI: AND 1 inputs / AND 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance AND 1 of the AND function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20035
BO: AND 1 output Q / AND 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 & I1 & I2 & I3 of instance AND 1 of the AND function block.
p20036
AND 1 run-time group / AND 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance AND 1 of the AND function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20037
AND 1 run sequence / AND 1 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
20
Description:
Setting parameter for the run sequence of instance AND 1 within the run-time group set in p20036.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-395
Parameters
List of Parameters
p20038[0...3]
BI: AND 2 inputs / AND 2 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance AND 2 of the AND function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20039
BO: AND 2 output Q / AND 2 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 & I1 & I2 & I3 of instance AND 2 of the AND function block.
p20040
AND 2 run-time group / AND 2 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance AND 2 of the AND function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20041
AND 2 run sequence / AND 2 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
30
Description:
Setting parameter for the run sequence of instance AND 2 within the run-time group set in p20040.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-396
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20042[0...3]
BI: AND 3 inputs / AND 3 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance AND 3 of the AND function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20043
BO: AND 3 output Q / AND 3 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 & I1 & I2 & I3 of instance AND 3 of the AND function block.
p20044
AND 3 run-time group / AND 3 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance AND 3 of the AND function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20045
AND 3 run sequence / AND 3 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
40
Description:
Setting parameter for the run sequence of instance AND 3 within the run-time group set in p20044.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-397
Parameters
List of Parameters
p20046[0...3]
BI: OR 0 inputs / OR 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance OR 0 of the OR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20047
BO: OR 0 output Q / OR 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 | I1 | I2 | I3 of instance OR 0 of the OR function block.
p20048
OR 0 run-time group / OR 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance OR 0 of the OR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20049
OR 0 run sequence / OR 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
60
Description:
Setting parameter for the run sequence of instance OR 0 within the run-time group set in p20048.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-398
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20050[0...3]
BI: OR 1 inputs / OR 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance OR 1 of the OR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20051
BO: OR 1 output Q / OR 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 | I1 | I2 | I3 of instance OR 1 of the OR function block.
p20052
OR 1 run-time group / OR 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance OR 1 of the OR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20053
OR 1 run sequence / OR 1 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
70
Description:
Setting parameter for the run sequence of instance OR 1 within the run-time group set in p20052.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-399
Parameters
List of Parameters
p20054[0...3]
BI: OR 2 inputs / OR 2 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance OR 2 of the OR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20055
BO: OR 2 output Q / OR 2 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 | I1 | I2 | I3 of instance OR 2 of the OR function block.
p20056
OR 2 run-time group / OR 2 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance OR 2 of the OR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20057
OR 2 run sequence / OR 2 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
80
Description:
Setting parameter for the run sequence of instance OR 2 within the run-time group set in p20056.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-400
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20058[0...3]
BI: OR 3 inputs / OR 3 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance OR 3 of the OR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20059
BO: OR 3 output Q / OR 3 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q = I0 | I1 | I2 | I3 of instance OR 3 of the OR function block.
p20060
OR 3 run-time group / OR 3 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance OR 3 of the OR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20061
OR 3 run sequence / OR 3 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
90
Description:
Setting parameter for the run sequence of instance OR 3 within the run-time group set in p20060.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-401
Parameters
List of Parameters
p20062[0...3]
BI: XOR 0 inputs / XOR 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance XOR 0 of the XOR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20063
BO: XOR 0 output Q / XOR 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q of instance XOR 0 of the XOR function block.
p20064
XOR 0 run-time group / XOR 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance XOR 0 of the XOR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20065
XOR 0 run sequence / XOR 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
110
Description:
Setting parameter for the run sequence of instance XOR 0 within the run-time group set in p20064.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-402
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20066[0...3]
BI: XOR 1 inputs / XOR 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance XOR 1 of the XOR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20067
BO: XOR 1 output Q / XOR 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q of instance XOR 1 of the XOR function block.
p20068
XOR 1 run-time group / XOR 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance XOR 1 of the XOR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20069
XOR 1 run sequence / XOR 1 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
120
Description:
Setting parameter for the run sequence of instance XOR 1 within the run-time group set in p20068.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-403
Parameters
List of Parameters
p20070[0...3]
BI: XOR 2 inputs / XOR 2 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance XOR 2 of the XOR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20071
BO: XOR 2 output Q / XOR 2 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q of instance XOR 2 of the XOR function block.
p20072
XOR 2 run-time group / XOR 2 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance XOR 2 of the XOR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20073
XOR 2 run sequence / XOR 2 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
130
Description:
Setting parameter for the run sequence of instance XOR 2 within the run-time group set in p20072.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-404
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20074[0...3]
BI: XOR 3 inputs / XOR 3 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0, I1, I2, I3 of instance XOR 3 of the XOR function block.
Index:
[0] = Input I0
[1] = Input I1
[2] = Input I2
[3] = Input I3
r20075
BO: XOR 3 output Q / XOR 3 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for binary quantity Q of instance XOR 3 of the XOR function block.
p20076
XOR 3 run-time group / XOR 3 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance XOR 3 of the XOR function block is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20077
XOR 3 run sequence / XOR 3 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
140
Description:
Setting parameter for the run sequence of instance XOR 3 within the run-time group set in p20076.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20078
BI: NOT 0 input I / NOT 0 input I
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source of input quantity I of instance NOT 0 of the inverter.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-405
Parameters
List of Parameters
r20079
BO: NOT 0 inverted output / NOT 0 inv output
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for the inverted output of instance NOT 0 of the inverter.
p20080
NOT 0 run-time group / NOT 0 RTG
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NOT 0 of the inverter is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20081
NOT 0 run sequence / NOT 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
160
Description:
Setting parameter for the run sequence of instance NOT 0 within the run-time group set in p20080.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20082
BI: NOT 1 input I / NOT 1 input I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source of input quantity I of instance NOT 1 of the inverter.
r20083
BO: NOT 1 inverted output / NOT 1 inv output
Description:
1-406
Factory setting
0
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for the inverted output of instance NOT 1 of the inverter.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20084
NOT 1 run-time group / NOT 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Value:
Setting parameter for the run-time group in which the instance NOT 1 of the inverter is to be called.
1:
Run-time group 1
2:
Run-time group 2
3:
Run-time group 3
4:
Run-time group 4
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20085
NOT 1 run sequence / NOT 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
170
Description:
Note:
Setting parameter for the run sequence of instance NOT 1 within the run-time group set in p20084.
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20086
BI: NOT 2 input I / NOT 2 input I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source of input quantity I of instance NOT 2 of the inverter.
r20087
BO: NOT 2 inverted output / NOT 2 inv output
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for the inverted output of instance NOT 2 of the inverter.
p20088
NOT 2 run-time group / NOT 2 RTG
Description:
Value:
Factory setting
0
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Setting parameter for the run-time group in which the instance NOT 2 of the inverter is to be called.
1:
Run-time group 1
2:
Run-time group 2
3:
Run-time group 3
4:
Run-time group 4
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-407
Parameters
List of Parameters
p20089
NOT 2 run sequence / NOT 2 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
180
Description:
Setting parameter for the run sequence of instance NOT 2 within the run-time group set in p20088.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20090
BI: NOT 3 input I / NOT 3 input I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source of input quantity I of instance NOT 3 of the inverter.
r20091
BO: NOT 3 inverted output / NOT 3 inv output
Factory setting
0
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for the inverted output of instance NOT 3 of the inverter.
p20092
NOT 3 run-time group / NOT 3 RTG
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NOT 3 of the inverter is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20093
NOT 3 run sequence / NOT 3 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
190
Description:
Setting parameter for the run sequence of instance NOT 3 within the run-time group set in p20092.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-408
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20094[0...3]
CI: ADD 0 inputs / ADD 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0, X1, X2, X3 of instance ADD 0 of the adder.
Index:
[0] = Input X0
[1] = Input X1
[2] = Input X2
[3] = Input X3
r20095
CO: ADD 0 output Y / ADD 0 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the output quantity Y = X0 + X1 + X2 + X3 of instance ADD 0 of the adder.
p20096
ADD 0 run-time group / ADD 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance ADD 0 of the adder is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20097
ADD 0 run sequence / ADD 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
210
Description:
Setting parameter for the run sequence of instance ADD 0 within the run-time group set in p20096.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20098[0...3]
CI: ADD 1 inputs / ADD 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0, X1, X2, X3 of instance ADD 1 of the adder.
Index:
[0] = Input X0
[1] = Input X1
[2] = Input X2
[3] = Input X3
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-409
Parameters
List of Parameters
r20099
CO: ADD 1 output Y / ADD 1 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the output quantity Y = X0 + X1 + X2 + X3 of instance ADD 1 of the adder.
p20100
ADD 1 run-time group / ADD 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance ADD 1 of the adder is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20101
ADD 1 run sequence / ADD 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
220
Description:
Setting parameter for the run sequence of instance ADD 1 within the run-time group set in p20100.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20102[0...1]
CI: SUB 0 inputs / SUB 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of minuend X1 and subtrahend X2 of instance SUB 0 of the subtractor.
Index:
[0] = Minuend X1
[1] = Subtrahend X2
r20103
CO: SUB 0 difference Y / SUB 0 difference Y
Description:
1-410
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for the difference Y = X1 - X2 of instance SUB 0 of the subtractor.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20104
SUB 0 run-time group / SUB 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance SUB 0 of the subtractor is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20105
SUB 0 run sequence / SUB 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
240
Description:
Setting parameter for the run sequence of instance SUB 0 within the run-time group set in p20104.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20106[0...1]
CI: SUB 1 inputs / SUB 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of minuend X1 and subtrahend X2 of instance SUB 1 of the subtractor.
Index:
[0] = Minuend X1
[1] = Subtrahend X2
r20107
CO: SUB 1 difference Y / SUB 1 difference Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the difference Y = X1 - X2 of instance SUB 1 of the subtractor.
p20108
SUB 1 run-time group / SUB 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance SUB 1 of the subtractor is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-411
Parameters
List of Parameters
p20109
SUB 1 run sequence / SUB 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
250
Description:
Setting parameter for the run sequence of instance SUB 1 within the run-time group set in p20108.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20110[0...3]
CI: MUL 0 inputs / MUL 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of the factors X0, X1, X2, X3 of instance MUL 0 of the multiplier.
Index:
[0] = Factor X0
[1] = Factor X1
[2] = Factor X2
[3] = Factor X3
r20111
CO: MUL 0 product Y / MUL 0 product Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the product Y = X0 * X1 * X2 * X3 of instance MUL 0 of the multiplier.
p20112
MUL 0 run-time group / MUL 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance MUL 0 of the multiplier is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20113
MUL 0 run sequence / MUL 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
270
Description:
Setting parameter for the run sequence of instance MUL 0 within the run-time group set in p20112.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-412
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20114[0...3]
CI: MUL 1 inputs / MUL 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of the factors X0, X1, X2, X3 of instance MUL 1 of the multiplier.
Index:
[0] = Factor X0
[1] = Factor X1
[2] = Factor X2
[3] = Factor X3
r20115
CO: MUL 1 product Y / MUL 1 product Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the product Y = X0 * X1 * X2 * X3 of instance MUL 1 of the multiplier.
p20116
MUL 1 run-time group / MUL 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance MUL 1 of the multiplier is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20117
MUL 1 run sequence / MUL 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
280
Description:
Setting parameter for the run sequence of instance MUL 1 within the run-time group set in p20116.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20118[0...1]
CI: DIV 0 inputs / DIV 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of dividend X1 and divisor X2 of instance DIV 0 of the divider.
Index:
[0] = Dividend X0
[1] = Divisor X1
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-413
Parameters
List of Parameters
r20119[0...2]
CO: DIV 0 quotient / DIV 0 quotient
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for quotients Y = X1/X2, integer number quotients YIN, and division remainder MOD = (Y - YIN)
x X2 of instance DIV 0 of the divider.
Index:
[0] = Quotient Y
[1] = Integer number quotient YIN
[2] = Div remainder MOD
r20120
BO: DIV 0 divisor is zero QF / DIV 0 divisor=0 QF
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for the signal QF that the divisor X2 of instance DIV 0 of the divider is zero.
X2 = 0.0 => QF = 1
p20121
DIV 0 run-time group / DIV 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance DIV 0 of the divider is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20122
DIV 0 run sequence / DIV 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
300
Description:
Setting parameter for the run sequence of instance DIV 0 within the run-time group set in p20121.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20123[0...1]
CI: DIV 1 inputs / DIV 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of dividend X1 and divisor X2 of instance DIV 1 of the divider.
Index:
[0] = Dividend X0
[1] = Divisor X1
1-414
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r20124[0...2]
CO: DIV 1 quotient / DIV 1 quotient
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for quotients Y = X1/X2, integer number quotients YIN, and division remainder MOD = (Y - YIN)
x X2 of instance DIV 1 of the divider.
Index:
[0] = Quotient Y
[1] = Integer number quotient YIN
[2] = Div remainder MOD
r20125
BO: DIV 1 divisor is zero QF / DIV 1 divisor=0 QF
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for the signal QF that the divisor X2 of instance DIV 1 of the divider is zero.
X2 = 0.0 => QF = 1
p20126
DIV 1 run-time group / DIV 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance DIV 1 of the divider is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20127
DIV 1 run sequence / DIV 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
310
Description:
Setting parameter for the run sequence of instance DIV 1 within the run-time group set in p20126.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20128
CI: AVA 0 input X / AVA 0 input X
Description:
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source of the input quantity X of instance AVA 0 of the absolute value generator with sign evaluation.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-415
Parameters
List of Parameters
r20129
CO: AVA 0 output Y / AVA 0 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Y of instance AVA 0 of the absolute value generator with sign evaluation.
r20130
BO: AVA 0 input negative SN / AVA 0 input neg SN
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for signal SN that the input quantity X of instance AVA 0 of the absolute value generator with
sign evaluation is negative.
X < 0.0 => SN = 1
p20131
AVA 0 run-time group / AVA 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance AVA 0 of the absolute value generator with sign evaluation is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20132
AVA 0 run sequence / AVA 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
340
Description:
Setting parameter for the run sequence of instance AVA 0 within the run-time group set in p20131.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20133
CI: AVA 1 input X / AVA 1 input X
Description:
1-416
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source of the input quantity X of instance AVA 1 of the absolute value generator with sign evaluation.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r20134
CO: AVA 1 output Y / AVA 1 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Y of instance AVA 1 of the absolute value generator with sign evaluation.
r20135
BO: AVA 1 input negative SN / AVA 1 input neg SN
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for signal SN that the input quantity X of instance AVA 1 of the absolute value generator with
sign evaluation is negative.
X < 0.0 => SN = 1
p20136
AVA 1 run-time group / AVA 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance AVA 1 of the absolute value generator with sign evaluation is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20137
AVA 1 run sequence / AVA 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
350
Description:
Setting parameter for the run sequence of instance AVA 1 within the run-time group set in p20136.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20138
Description:
BI: MFP 0 input pulse I / MFP 0 inp_pulse I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance MFP 0 of the pulse generator.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-417
Parameters
List of Parameters
p20139
MFP 0 pulse duration in ms / MFP 0 pulse_dur ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Description:
Setting parameter for pulse duration T in milliseconds of instance MFP 0 of the pulse generator.
r20140
BO: MFP 0 output Q / MFP 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance MFP 0 of the pulse generator.
p20141
MFP 0 run-time group / MFP 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance MFP 0 of the pulse generator is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20142
MFP 0 run sequence / MFP 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
370
Description:
Setting parameter for the run sequence of instance MFP 0 within the run-time group set in p20141.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20143
Description:
1-418
BI: MFP 1 input pulse I / MFP 1 inp_pulse I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance MFP 1 of the pulse generator.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20144
MFP 1 pulse duration in ms / MFP 1 pulse_dur ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Description:
Setting parameter for pulse duration T in milliseconds of instance MFP 1 of the pulse generator.
r20145
BO: MFP 1 output Q / MFP 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance MFP 1 of the pulse generator.
p20146
MFP 1 run-time group / MFP 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance MFP 1 of the pulse generator is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20147
MFP 1 run sequence / MFP 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
380
Description:
Setting parameter for the run sequence of instance MFP 1 within the run-time group set in p20146.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20148
BI: PCL 0 input pulse I / PCL 0 inp_pulse I
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance PCL 0 of the pulse shortener.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-419
Parameters
List of Parameters
p20149
Description:
r20150
PCL 0 pulse duration in ms / PCL 0 pulse_dur ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Setting parameter for pulse duration T in milliseconds of instance PCL 0 of the pulse shortener.
BO: PCL 0 output Q / PCL 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PCL 0 of the pulse shortener.
p20151
PCL 0 run-time group / PCL 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance PCL 0 of the pulse shortener is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20152
PCL 0 run sequence / PCL 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
400
Description:
Setting parameter for the run sequence of instance PCL 0 within the run-time group set in p20151.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20153
BI: PCL 1 input pulse I / PCL 1 inp_pulse I
Description:
1-420
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance PCL 1 of the pulse shortener.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20154
Description:
r20155
PCL 1 pulse duration in ms / PCL 1 pulse_dur ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Setting parameter for pulse duration T in milliseconds of instance PCL 1 of the pulse shortener.
BO: PCL 1 output Q / PCL 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PCL 1 of the pulse shortener.
p20156
PCL 1 run-time group / PCL 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance PCL 1 of the pulse shortener is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20157
PCL 1 run sequence / PCL 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
410
Description:
Setting parameter for the run sequence of instance PCL 1 within the run-time group set in p20156.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20158
BI: PDE 0 input pulse I / PDE 0 inp_pulse I
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance PDE 0 of the closing delay device.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-421
Parameters
List of Parameters
p20159
PDE 0 pulse delay time in ms / PDE 0 t_del ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Description:
Setting parameter for pulse delay time T in milliseconds of instance PDE 0 of the closing delay device.
r20160
BO: PDE 0 output Q / PDE 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PDE 0 of the closing delay device.
p20161
PDE 0 run-time group / PDE 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance PDE 0 of the closing delay device is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20162
PDE 0 run sequence / PDE 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
430
Description:
Setting parameter for the run sequence of instance PDE 0 within the run-time group set in p20161.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20163
BI: PDE 1 input pulse I / PDE 1 inp_pulse I
Description:
1-422
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance PDE 1 of the closing delay device.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20164
PDE 1 pulse delay time in ms / PDE 1 t_del ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Description:
Setting parameter for pulse delay time T in milliseconds of instance PDE 1 of the closing delay device.
r20165
BO: PDE 1 output Q / PDE 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PDE 1 of the closing delay device.
p20166
PDE 1 run-time group / PDE 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance PDE 1 of the closing delay device is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20167
PDE 1 run sequence / PDE 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
440
Description:
Setting parameter for the run sequence of instance PDE 1 within the run-time group set in p20166.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20168
BI: PDF 0 input pulse I / PDF 0 inp_pulse I
Description:
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance PDF 0 of the breaking delay device.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-423
Parameters
List of Parameters
p20169
Description:
r20170
PDF 0 pulse extension time in ms / PDF 0 t_ext ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Setting parameter for pulse extension time T in milliseconds of instance PDF 0 of the breaking delay device.
BO: PDF 0 output Q / PDF 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PDF 0 of the breaking delay device.
p20171
PDF 0 run-time group / PDF 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance PDF 0 of the breaking delay device is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20172
PDF 0 run sequence / PDF 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
460
Description:
Setting parameter for the run sequence of instance PDF 0 within the run-time group set in p20171.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20173
BI: PDF 1 input pulse I / PDF 1 inp_pulse I
Description:
1-424
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the input pulse I of instance PDF 1 of the breaking delay device.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20174
Description:
r20175
PDF 1 pulse extension time in ms / PDF 1 t_ext ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Setting parameter for pulse extension time T in milliseconds of instance PDF 1 of the breaking delay device.
BO: PDF 1 output Q / PDF 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PDF 1 of the breaking delay device.
p20176
PDF 1 run-time group / PDF 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance PDF 1 of the breaking delay device is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20177
PDF 1 run sequence / PDF 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
470
Description:
Setting parameter for the run sequence of instance PDF 1 within the run-time group set in p20176.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20178[0...1]
BI: PST 0 inputs / PST 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for input pulse I and the reset input R of instance PST 0 of the pulse extension element.
Index:
[0] = Input pulse I
[1] = Reset input R
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-425
Parameters
List of Parameters
p20179
PST 0 pulse duration in ms / PST 0 pulse_dur ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Description:
Setting parameter for pulse duration T in milliseconds of instance PST 0 of the pulse extension element.
r20180
BO: PST 0 output Q / PST 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PST 0 of the pulse extension element.
p20181
PST 0 run-time group / PST 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance PST 0 of the pulse extension element is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20182
PST 0 run sequence / PST 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
490
Description:
Setting parameter for the run sequence of instance PST 0 within the run-time group set in p20181.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20183[0...1]
BI: PST 1 inputs / PST 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for input pulse I and the reset input R of instance PST 1 of the pulse extension element.
Index:
[0] = Input pulse I
[1] = Reset input R
1-426
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20184
PST 1 pulse duration in ms / PST 1 pulse_dur ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
60000.00
Factory setting
0.00
Description:
Setting parameter for pulse duration T in milliseconds of instance PST 1 of the pulse extension element.
r20185
BO: PST 1 output Q / PST 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output pulse Q of instance PST 1 of the pulse extension element.
p20186
PST 1 run-time group / PST 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance PST 1 of the pulse extension element is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20187
PST 1 run sequence / PST 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
500
Description:
Setting parameter for the run sequence of instance PST 1 within the run-time group set in p20186.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20188[0...1]
BI: RSR 0 inputs / RSR 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for set input S and reset input R of instance RSR 0 of the RS flipflop.
Index:
[0] = Set S
[1] = Reset R
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-427
Parameters
List of Parameters
r20189
BO: RSR 0 output Q / RSR 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for output Q of instance RSR 0 of the RS flipflop
r20190
BO: RSR 0 inverted output QN / RSR 0 inv outp QN
Factory setting
-
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for inverted output QN of instance RSR 0 of the RS flipflop.
p20191
RSR 0 run-time group / RSR 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance RSR 0 of the RS flipflop is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20192
RSR 0 run sequence / RSR 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
520
Description:
Setting parameter for the run sequence of instance RSR 0 within the run-time group set in p20191.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20193[0...1]
BI: RSR 1 inputs / RSR 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for set input S and reset input R of instance RSR 1 of the RS flipflop.
Index:
[0] = Set S
[1] = Reset R
1-428
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r20194
BO: RSR 1 output Q / RSR 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for output Q of instance RSR 1 of the RS flipflop
r20195
BO: RSR 1 inverted output QN / RSR 1 inv outp QN
Factory setting
-
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for inverted output QN of instance RSR 1 of the RS flipflop.
p20196
RSR 1 run-time group / RSR 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance RSR 1 of the RS flipflop is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20197
RSR 1 run sequence / RSR 1 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
530
Description:
Setting parameter for the run sequence of instance RSR 1 within the run-time group set in p20196.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20198[0...3]
BI: DFR 0 inputs / DFR 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for trigger input I, D input D, set input S, and reset input R of instance DFR 0 of the D flipflop.
Index:
[0] = Trigger input I
[1] = D input D
[2] = Set S
[3] = Reset R
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-429
Parameters
List of Parameters
r20199
Description:
r20200
BO: DFR 0 output Q / DFR 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for output Q of instance DFR 0 of the D flipflop.
BO: DFR 0 inverted output QN / DFR 0 inv outp QN
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the inverted output QN of instance DFR 0 of the D flipflop.
p20201
DFR 0 run-time group / DFR 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance DFR 0 of the D flipflop is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20202
DFR 0 run sequence / DFR 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
550
Description:
Setting parameter for the run sequence of instance DFR 0 within the run-time group set in p20201.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20203[0...3]
BI: DFR 1 inputs / DFR 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for trigger input I, D input D, set input S, and reset input R of instance DFR 1 of the D flipflop.
Index:
[0] = Trigger input I
[1] = D input D
[2] = Set S
[3] = Reset R
1-430
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r20204
Description:
r20205
BO: DFR 1 output Q / DFR 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for output Q of instance DFR 1 of the D flipflop.
BO: DFR 1 inverted output QN / DFR 1 inv outp QN
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the inverted output QN of instance DFR 1 of the D flipflop.
p20206
DFR 1 run-time group / DFR 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance DFR 1 of the D flipflop is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20207
DFR 1 run sequence / DFR 1 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
560
Description:
Setting parameter for the run-time group of instance DFR 1 within the run-time group set in p20206.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20208[0...1]
BI: BSW 0 inputs / BSW 0 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0 and I1 of instance BSW 0 of the binary changeover switch.
Index:
[0] = Input I0
[1] = Input I1
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-431
Parameters
List of Parameters
p20209
BI: BSW 0 switch setting I / BSW 0 sw_setting
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of the switch setting I of instance BSW 0 of the binary changeover switch.
r20210
BO: BSW 0 output Q / BSW 0 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Q of instance BSW 0 of the binary changeover switch.
p20211
BSW 0 run-time group / BSW 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance BSW 0 of the binary changeover switch is to be
called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20212
BSW 0 run sequence / BSW 0 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
580
Description:
Setting parameter for the run sequence of instance BSW 0 within the run-time group set in p20211.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20213[0...1]
BI: BSW 1 inputs / BSW 1 inputs
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities I0 and I1 of instance BSW 1 of the binary changeover switch.
Index:
[0] = Input I0
[1] = Input I1
1-432
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20214
BI: BSW 1 switch setting I / BSW 1 sw_setting
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of the switch setting I of instance BSW 1 of the binary changeover switch.
r20215
BO: BSW 1 output Q / BSW 1 output Q
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Q of instance BSW 1 of the binary changeover switch.
p20216
BSW 1 run-time group / BSW 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance BSW 1 of the binary changeover switch is to be
called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20217
BSW 1 run sequence / BSW 1 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
590
Description:
Setting parameter for the run sequence of instance BSW 1 within the run-time group set in p20216.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20218[0...1]
CI: NSW 0 inputs / NSW 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0 and X1 of instance NSW 0 of the numeric changeover switch.
Index:
[0] = Input X0
[1] = Input X1
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-433
Parameters
List of Parameters
p20219
BI: NSW 0 switch setting I / NSW 0 sw_setting
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of the switch setting I of instance NSW 0 of the numeric changeover switch.
r20220
CO: NSW 0 output Y / NSW 0 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Y of instance NSW 0 of the numeric changeover switch.
p20221
NSW 0 run-time group / NSW 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NSW 0 of the numeric changeover switch is to be
called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20222
NSW 0 run sequence / NSW 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
610
Description:
Setting parameter for the run sequence of instance NSW 0 within the run-time group set in p20221.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20223[0...1]
CI: NSW 1 inputs / NSW 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0 and X1 of instance NSW 1 of the numeric changeover switch.
Index:
[0] = Input X0
[1] = Input X1
1-434
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20224
BI: NSW 1 switch setting I / NSW 1 sw_setting
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of the switch setting I of instance NSW 1 of the numeric changeover switch.
r20225
CO: NSW 1 output Y / NSW 1 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Y of instance NSW 1 of the numeric changeover switch.
p20226
NSW 1 run-time group / NSW 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NSW 1 of the numeric changeover switch is to be
called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20227
NSW 1 run sequence / NSW 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
620
Description:
Setting parameter for the run sequence of instance NSW 1 within the run-time group set in p20226.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20228
CI: LIM 0 input X / LIM 0 input X
Description:
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source of input quantity X of instance LIM 0 of the limiter.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-435
Parameters
List of Parameters
p20229
LIM 0 upper limit value LU / LIM 0 upper lim LU
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for the upper limit value LU of instance LIM 0 of the limiter.
p20230
LIM 0 lower limit value LL / LIM 0 lower lim LL
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Description:
Setting parameter for the lower limit value LL of instance LIM 0 of the limiter.
r20231
CO: LIM 0 output Y / LIM 0 output Y
Factory setting
0.0000
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the limited output quantity Y of instance LIM 0 of the limiter.
r20232
BO: LIM 0 input quantity at the upper limit QU / LIM 0 QU
Description:
r20233
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter of instance LIM 0 of limiter QU (upper limit reached), i.e. QU = 1 for X >= LU.
BO: LIM 0 input quantity at the lower limit QL / LIM 0 QL
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter of instance LIM 0 of limiter QL (lower limit reached), i.e. QL = 1 for X <= LL.
p20234
LIM 0 run-time group / LIM 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance LIM 0 of the limiter is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
1-436
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20235
LIM 0 run sequence / LIM 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
640
Description:
Setting parameter for the run sequence of instance LIM 0 within the run-time group set in p20234.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20236
CI: LIM 1 input X / LIM 1 input X
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source of input quantity X of instance LIM 1 of the limiter.
p20237
LIM 1 upper limit value LU / LIM 1 upper lim LU
Factory setting
0
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for the upper limit value LU of instance LIM 1 of the limiter.
p20238
LIM 1 lower limit value LL / LIM 1 lower lim LL
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Description:
Setting parameter for the lower limit value LL of instance LIM 1 of the limiter.
r20239
CO: LIM 1 output Y / LIM 1 output Y
Factory setting
0.0000
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the limited output quantity Y of instance LIM 1 of the limiter.
r20240
BO: LIM 1 input quantity at the upper limit QU / LIM 1 QU
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter of instance LIM 1 of limiter QU (upper limit reached), i.e. QU = 1 for X >= LU.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-437
Parameters
List of Parameters
r20241
BO: LIM 1 input quantity at the lower limit QL / LIM 1 QL
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter of instance LIM 1 of limiter QL (lower limit reached), i.e. QL = 1 for X <= LL.
p20242
LIM 1 run-time group / LIM 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance LIM 1 of the limiter is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20243
LIM 1 run sequence / LIM 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
650
Description:
Setting parameter for the run sequence of instance LIM 1 within the run-time group set in p20242.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20244[0...1]
CI: PT1 0 inputs / PT1 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantity X and of setting value SV of instance PT1 0 of the smoothing element.
Index:
[0] = Input X
[1] = Setting value SV
p20245
BI: PT1 0 accept setting value S / PT1 0 acc set val
Description:
1-438
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source for the "accept setting value" signal of instant PT1 0 of the smoothing element.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20246
PT1 0 smoothing time constant in ms / PT1 0 T_smooth ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
340.28235E36
Factory setting
0.00
Description:
Sets the smoothing time constant T in milliseconds of instance PT1 0 of the smoothing element.
r20247
CO: PT1 0 output Y / PT1 0 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the smoothed output quantity Y of instance PT1 0 of the smoothing element.
p20248
PT1 0 run-time group / PT1 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance PT1 0 of the smoothing element is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20249
PT1 0 run sequence / PT1 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
670
Description:
Setting parameter for the run sequence of instance PT1 0 within the run-time group set in p20248.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20250[0...1]
CI: PT1 1 inputs / PT1 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantity X and of setting value SV of instance PT1 1 of the smoothing element.
Index:
[0] = Input X
[1] = Setting value SV
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-439
Parameters
List of Parameters
p20251
BI: PT1 1 accept setting value S / PT1 1 acc set val
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the "accept setting value" signal of instant PT1 1 of the smoothing element.
p20252
PT1 1 smoothing time constant in ms / PT1 1 T_smooth ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
340.28235E36
Factory setting
0.00
Description:
Sets the smoothing time constant T in milliseconds of instance PT1 1 of the smoothing element.
r20253
CO: PT1 1 output Y / PT1 1 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the smoothed output quantity Y of instance PT1 1 of the smoothing element.
p20254
PT1 1 run-time group / PT1 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance PT1 1 of the smoothing element is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20255
PT1 1 run sequence / PT1 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
680
Description:
Setting parameter for the run sequence of instance PT1 1 within the run-time group set in p20254.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
1-440
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20256[0...1]
CI: INT 0 inputs / INT 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantity X and of setting value SV of instance INT 0 of the integrator.
Index:
[0] = Input X
[1] = Setting value SV
p20257
INT 0 upper limit value LU / INT 0 upper lim LU
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Description:
Sets the upper limit value LU of instance INT 0 of the integrator.
p20258
INT 0 lower limit value LL / INT 0 lower lim LL
Factory setting
0.0000
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Description:
Sets the lower limit value LL of instance INT 0 of the integrator.
p20259
INT 0 integrating time constant in ms / INT 0 T_Integr ms
Factory setting
0.0000
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
340.28235E36
Factory setting
0.00
Description:
Sets the integrating time constant Ti in milliseconds of instance INT 0 of the integrator.
p20260
BI: INT 0 accept setting value S / INT 0 acc set val
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source for the "accept setting value" signal of instant INT 0 of the integrator.
r20261
CO: INT 0 output Y / INT 0 output Y
Description:
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for output quantity Y of instance INT 0 of the integrator.
If LL>= LU, then the output quantity Y = LU.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-441
Parameters
List of Parameters
r20262
BO: INT 0 integrator at the upper limit QU / INT 0 QU
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the signal QU that output quantity Y of instance INT 0 of the integrator has reached the upper
limit value LU.
r20263
BO: INT 0 integrator at the lower limit QL / INT 0 QL
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the signal QL that output quantity Y of instance INT 0 of the integrator has reached the lower
limit value LL.
p20264
INT 0 run-time group / INT 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance INT 0 of the integrator is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20265
INT 0 run sequence / INT 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
700
Description:
Setting parameter for the run sequence of instance INT 0 within the run-time group set in p20264.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20266
CI: LVM 0 input X / LVM 0 input X
Description:
1-442
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Sets the signal source of input quantity X of instance LVM 0 of the double-sided limiter.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20267
LVM 0 interval average value M / LVM 0 avg value M
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for the interval average M of instance LVM 0 of the double-sided limiter.
p20268
LVM 0 interval limit L / LVM 0 limit L
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for the interval limit L of instance LVM 0 of the double-sided limiter.
p20269
LVM 0 hyst HY / LVM 0 hyst HY
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for hysteresis HY of instance LVM 0 of the double-sided limiter.
r20270
BO: LVM 0 input quantity above interval QU / LVM 0 X above QU
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter of instance LVM 0 of the double-sided limiter that input quantity X was at least once X > M + L
and X is >= M + L - HY.
r20271
BO: LVM 0 input quantity within interval QM / LVM 0 X within QM
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter of instance LVM 0 of the double-sided limiter that the input quantity X lies within the interval.
r20272
BO: LVM 0 input quantity below interval QL / LVM 0 X below QL
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter of instance LVM 0 of the double-sided limiter that input quantity X was at least once X < M - L
and X is <= M - L + HY.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-443
Parameters
List of Parameters
p20273
LVM 0 run-time group / LVM 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance LVM 0 of the double-sided limiter is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20274
LVM 0 run sequence / LVM 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
720
Description:
Setting parameter for the run sequence of instance LVM 0 within the run-time group set in p20273.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20275
CI: LVM 1 input X / LVM 1 input X
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantity X of instance LVM 1 of the double-sided limiter.
p20276
LVM 1 interval average value M / LVM 1 avg value M
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for the interval average M of instance LVM 1 of the double-sided limiter.
p20277
LVM 1 interval limit L / LVM 1 limit L
Description:
1-444
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Setting parameter for the interval limit L of instance LVM 1 of the double-sided limiter.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20278
LVM 1 hyst HY / LVM 1 hyst HY
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-340.28235E36
Max
340.28235E36
Factory setting
0.0000
Description:
Setting parameter for hysteresis HY of instance LVM 1 of the double-sided limiter.
r20279
BO: LVM 1 input quantity above interval QU / LVM 1 X above QU
Description:
r20280
Description:
r20281
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter of instance LVM 1 of the double-sided limiter that input quantity X was at least once X > M + L
and X is >= M + L - HY.
BO: LVM 1 input quantity within interval QM / LVM 1 X within QM
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter of instance LVM 1 of the double-sided limiter that the input quantity X lies within the interval.
BO: LVM 1 input quantity below interval QL / LVM 1 X below QL
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter of instance LVM 1 of the double-sided limiter that input quantity X was at least once X < M - L
and X is <= M - L + HY.
p20282
LVM 1 run-time group / LVM 1 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance LVM 1 of the double-sided limiter is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-445
Parameters
List of Parameters
p20283
LVM 1 run sequence / LVM 1 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
7999
Factory setting
730
Description:
Setting parameter for the run sequence of instance LVM within the run-time group set in p20282.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20284
CI: DIF 0 input X / DIF 0 input X
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantity X of instance DIF 0 of the differentiating element.
p20285
DIF 0 differentiating time constant in ms / DIF 0 T_diff ms
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0.00
Max
340.28235E36
Factory setting
0.00
Description:
Sets the differentiating time constant Td in milliseconds of instance DIF 0 of the differentiating element.
r20286
CO: DIF 0 output Y / DIF 0 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for output quantity Y of instance DIF 0 of the differentiating element.
p20287
DIF 0 run-time group / DIF 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which instance DIF 0 of the differentiating element is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
1-446
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
p20288
DIF 0 run sequence / DIF 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
750
Description:
Setting parameter for the run sequence of instance DIF 0 within the run-time group set in p20287.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20300
BI: NOT 4 input I / NOT 4 input I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source of input quantity I of instance NOT 4 of the inverter.
r20301
BO: NOT 4 inverted output / NOT 4 inv output
Factory setting
0
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for the inverted output of instance NOT 4 of the inverter.
p20302
NOT 4 run-time group / NOT 4 RTG
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NOT 4 of the inverter is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20303
NOT 4 run sequence / NOT 4 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
770
Description:
Setting parameter for the run sequence of instance NOT 4 within the run-time group set in p20302.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-447
Parameters
List of Parameters
p20304
BI: NOT 5 input I / NOT 5 input I
Access level: 3
Calculated: -
Data type: U32 / Binary
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Sets the signal source of input quantity I of instance NOT 5 of the inverter.
r20305
BO: NOT 5 inverted output / NOT 5 inv output
Factory setting
0
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Description:
Display parameter for the inverted output of instance NOT 5 of the inverter.
p20306
NOT 5 run-time group / NOT 5 RTG
Factory setting
-
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
1
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NOT 5 of the inverter is to be called.
Value:
1:
2:
3:
4:
5:
6:
9999:
p20307
NOT 5 run sequence / NOT 5 RunSeq
Run-time group 1
Run-time group 2
Run-time group 3
Run-time group 4
Run-time group 5
Run-time group 6
Do not calculate
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
780
Description:
Setting parameter for the run sequence of instance NOT 5 within the run-time group set in p20306.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20308[0...3]
CI: ADD 2 inputs / ADD 2 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0, X1, X2, X3 of instance ADD 2 of the adder.
Index:
[0] = Input X0
[1] = Input X1
[2] = Input X2
[3] = Input X3
1-448
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r20309
CO: ADD 2 output Y / ADD 2 output Y
Access level: 3
Calculated: -
Data type: FloatingPoint32
Can be changed: -
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Description:
Display parameter for the output quantity Y = X0 + X1 + X2 + X3 of instance ADD 2 of the adder.
p20310
ADD 2 run-time group / ADD 2 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance ADD 2 of the adder is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20311
ADD 2 run sequence / ADD 2 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
800
Description:
Setting parameter for the run sequence of instance ADD 2 within the run-time group set in p20310.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20312[0...1]
CI: NCM 0 inputs / NCM 0 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0 and X1 of instance NCM 0 of the numeric comparator.
Index:
[0] = Input X0
[1] = Input X1
r20313
BO: NCM 0 output QU / NCM 0 output QU
Description:
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for binary quantity QU of instance NCM 0 of the numeric comparator.
QU is only set if X0 > X1.
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
1-449
Parameters
List of Parameters
r20314
Description:
BO: NCM 0 output QE / NCM 0 output QE
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for binary quantity QE of instance NCM 0 of the numeric comparator.
QE is only set if X0 = X1.
r20315
Description:
BO: NCM 0 output QL / NCM 0 output QL
Access level: 3
Calculated: -
Data type: Unsigned32
Can be changed: -
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
-
Display parameter for binary quantity QL of instance NCM 0 of the numeric comparator.
QL is only set if X0 < X1.
p20316
NCM 0 run-time group / NCM 0 RTG
Access level: 3
Calculated: -
Data type: Integer16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
5
Max
9999
Factory setting
9999
Description:
Setting parameter for the run-time group in which the instance NCM 0 of the numeric comparator is to be called.
Value:
5:
Run-time group 5
6:
Run-time group 6
9999: Do not calculate
p20317
NCM 0 run sequence / NCM 0 RunSeq
Access level: 3
Calculated: -
Data type: Unsigned16
Can be changed: T
Scaling: -
Data set: -
Units group: -
Unit selection: -
Min
0
Max
32000
Factory setting
820
Description:
Setting parameter for the run sequence of instance NCM 0 within the run-time group set in p20316.
Note:
The function blocks with a lower run sequence value are calculated before function blocks with a higher run
sequence value.
p20318[0...1]
CI: NCM 1 inputs / NCM 1 inputs
Access level: 3
Calculated: -
Data type: U32 / FloatingPoint32
Can be changed: T
Scaling: PERCENT
Data set: -
Units group: -
Unit selection: -
Min
-
Max
-
Factory setting
0
Description:
Sets the signal source of input quantities X0 and X1 of instance NCM 1 of the numeric comparator.
Index:
[0] = Input X0
[1] = Input X1
1-450
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Parameters
List of Parameters
r20319
Description: