D-Link DVG-2102S User`s manual

DVG-2102S
VoIP Telephone Adapter
User’s Manual
Version 1.2
(Feb. 2010)
© 2010 D-Link Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden.
Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation/D-Link Systems
Inc.; Other trademarks and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade
names other than its own.
Warranty: please contact your D-Link Authorized Reseller or the D-Link Branch Office nearest your place of
purchase for information about the warranty offered on your D-Link product.
Information in this document is subject to change without notice.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
‧ Reorient or relocate the receiving antenna.
‧ Increase the separation between the equipment and receiver.
‧ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‧ Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse B. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem
Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase B. En un entorno doméstico, puede causar interferencias de radio, en cuyo case, puede
requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe B. Dans un environnement domestique, ce produit pourrait causer des interférences
radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe B. Se utilizzato in ambiente domestico il prodotto può causare interferenze
radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.
WARNING:
(1) Stacking is forbidden.
(2) DO NOT connect the phone ports to each other (FXS to FXS).
(3) DO NOT power off your device before the firmware upgrade is complete.
Contents
1. Introduction ..................................................................................................................................................... 4
1-1 Product Overview ..................................................................................................................................... 4
1-2 Hardware Description............................................................................................................................... 5
2. VoIP Telephone Adapter Web Configuration ................................................................................................. 7
2-1 SETUP ..................................................................................................................................................... 8
2.1.1 Internet Setup................................................................................................................................. 8
2-2 ADVANCED ........................................................................................................................................... 12
2.2.1 DoS Prevention ............................................................................................................................ 12
2-3 MAINTENANCE ..................................................................................................................................... 14
2-3-1 Device Management .................................................................................................................... 14
2-3-2 Backup and Restore .................................................................................................................... 15
2-3-3 Dynamic DNS .............................................................................................................................. 16
2-3-4 Diagnostics .................................................................................................................................. 17
2-4 STATUS ................................................................................................................................................. 18
2-4-1 Device Info ................................................................................................................................... 18
2-4-2 VoIP Status .................................................................................................................................. 19
2-4-3 Statistics ...................................................................................................................................... 19
2-4-4 Routing Table ............................................................................................................................... 20
2-4-5 Logout.......................................................................................................................................... 20
DVG-2102S User’s Manual
Product Overview
1. Introduction
1-1 Product Overview
The DVG-2102S is designed to carry both voice and facsimile over the IP network. It uses the industry standard
SIP call control protocol so as to be compatible with free registration services or VoIP service providers’ systems.
As a standard user agent, it is compatible with all common Soft Switches and SIP proxy servers. While running
optional server software, the VoIP Telephone Adapter can be configured to establish a private VoIP network over
the Internet without a third-party SIP Proxy Server.
The DVG-2102S can be seamlessly integrated into an existing network by connecting to a phone set and fax
machine. With only a broadband connection such as an ADSL bridge/router, a Cable Modem or a leased-line
router, the VoIP Telephone Adapter allows you to use voice and fax services over IP in order to reduce the cost of
all long distance calls.
The DVG-2102S can be configured a fixed IP address or it can have one dynamically assigned by DHCP or
PPPoE. It adopts either the G.711, G.726, G.729A or G.723.1 voice compression format to save network
bandwidth while providing real-time, toll quality voice transmission and reception.
D-Link Systems, Inc.
4
DVG-2102S User’s Manual
Telephone Interface Description
1-2 Hardware Description
Front Panel
y Power LED: Green light indicates a normal power supply.
A fast blinking light indicates the SIP TA is not registered. A
slow blinking light indicates the SIP TA is communicating
with the Auto Provision Server.
y WAN LED: When a connection is established the 10 or
100 LED will light up solid. The LED will blink to indicate
activity. If the 10 or 100 LED does not light up when a
cable is connected, verify the cable connections and make
sure your devices are powered on.
y Phone LED: This LED displays the VoIP status and
Hook/Ringing activity on the phone port that is used to
connect your normal telephone(s). If a phone connected to
a phone port is off the hook or in use, this LED will light
solid. When a phone is ringing, the indicator will blink.
D-Link Systems, Inc.
5
DVG-2102S User’s Manual
Telephone Interface Description
Rear Panel
1.
2.
Power Receptor: Receptor for the provided power adapter.
WAN: Connect to your broadband modem using an Ethernet cable or connect to your Ethernet
enabled computers using Ethernet cabling.
3.
Phone Port (1-2): Connect to your phones using standard phone cabling (RJ-11).
WARNING: DO NOT connect the phone ports to each other (FXS to FXS). Doing so may damage
your VoIP Telephone Adapter.
Use Reset Button to restore factory default settings:
1.
2.
3.
Power on.
Press and hold the reset button for 5 seconds.
Release the reset button. Factory settings will be restored.
D-Link Systems, Inc.
6
DVG-2102S User’s Manual
SETUP
2. VoIP Telephone Adapter Web Configuration
To access the web-based configuration utility, open a web browser such as Internet Explorer and enter the IP
address of the DVG-2102S from WAN port.
Open your Web browser and type
http://192.168.8.254:8080 into the URL
address box. Press the Enter or Return
Click Login to enter Web Site.
The username is “User” and
leave password to be blank
D-Link Systems, Inc.
7
DVG-2102S User’s Manual
SETUP
2-1 SETUP
2.1.1 Internet Setup
WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The WAN
settings are provided to you by your ISP and oftentimes referred to as "public settings". Please select the
appropriate option for your specific ISP.
IP Configuration (Setting WAN Port)
There are five methods of obtaining a WAN port IP address:
1.
DHCP, which means a Dynamic IP (Cable Modem)
2.
Static IP
3.
PPPoE (dial-up ADSL)
Methods for using DHCP and PPPoE for obtaining an IP address may vary. If you are not familiar with
creating a network connection, please contact your local ISP.
After selecting the suitable option, click Accept at the bottom of the screen to save the settings.
You need to save the changes and restart the VoIP Telephone Adapter to make the changes active. Saving
the settings: Click MAINTENANCE and select Save/Restart in System from the left menu. Tick Save
Settings and Restart, then click Accept. Wait for about 40 seconds before the VoIP Telephone Adapter
obtaining an IP address by the method you selected.
Note: When the system has obtained a new IP address, and you are using a WAN port to enter the Web
Configuration Screen, the new IP address has to be used before you can get connected to the VoIP
Telephone Adapter. The same principle applies to the next two settings.
D-Link Systems, Inc.
8
DVG-2102S User’s Manual
SETUP
SETUP → Internet Setup
SETUP → Internet Setup
DHCP: Select this option if your ISP (Internet Service Provider) provides you an IP address automatically.
Cable modem providers typically use dynamic assignment of IP Address. The Host Name field is optional
but may be required by some Internet Service Providers.
SETUP → Internet Setup
Static IP: Select this option if your ISP (Internet Service Provider) provides you a Static IP address. Enter
the IP address, Subnet Mask and Default Gateway IP.
D-Link Systems, Inc.
9
DVG-2102S User’s Manual
SETUP
SETUP → Internet Setup
PPPoE: Select this option if your ISP requires you to use a PPPoE (Point-to-Point Protocol over Ethernet)
connection. Enter the PPPoE Account, PPPoE Password and re-enter Password to confirm.
SETUP → Internet Setup
D-Link Systems, Inc.
10
DVG-2102S User’s Manual
SETUP
SETUP → Internet Setup
Before the VoIP Gateway obtains an IP address, you can use the IP address of WAN ALIAS to browse the
Web UI for configuration.
IP Address: The default IP is 192.168.8.254.
Subnet Mask: Leave the Subnet Mask as default: 255.255.255.0.
SETUP → Internet Setup
Domain Name Server Assignment: Select Auto or Manual to get the IP address of Domain Name Server
assigned by ISP or manually.
Domain Name Server IP: Enter the primary and secondary IP address of Domain Name Server if Domain
Name Server Assignment is Manual. Otherwise, the VoIP Telephone Adapter will not be able to access
hosts using hostnames instead of IPs.
D-Link Systems, Inc.
11
DVG-2102S User’s Manual
ADVANCED
2-2 ADVANCED
2.2.1 DoS Prevention
ADVANCED → DoS Prevention
D-Link Systems, Inc.
12
DVG-2102S User’s Manual
ADVANCED
ADVANCED → DoS Prevention
Enable DoS Prevention: Check the box to prevent DoS attacks from WAN. There are various types of
DoS attacking. Leave settings in this field to the default if you are not familiar with it.
ADVANCED → DoS Prevention
Enable Source IP Blocking: Check the box to block a particular IP address that detects the connection
confirmed with the type of DoS attacking.
Blocking Time: Enter the blocking time to block the particular IP.
D-Link Systems, Inc.
13
DVG-2102S User’s Manual
MAINTENANCE
2-3 MAINTENANCE
2-3-1 Device Management
MAINTENANCE → Device Management
Password: By default there is no password configured. It is highly recommended that you create a
password to keep your VoIP Telephone Adapter secure.
D-Link Systems, Inc.
14
DVG-2102S User’s Manual
MAINTENANCE
2-3-2 Backup and Restore
Save and Reboot
MAINTENANCE → Backup and Restore
Save All Settings: Click the Save All Settings check box and reboot the system after completing changes.
The new settings will take effect after the VoIP Telephone Adapter is restarted.
Restart: Click the Reboot button to reboot the system.
Restore Default Settings
MAINTENANCE → Backup and Restore
Select Restore Default Settings to reset the VoIP Telephone Adapter’s settings back to the factory default
settings.
D-Link Systems, Inc.
15
DVG-2102S User’s Manual
MAINTENANCE
2-3-3 Dynamic DNS
ADVANCED → Dynamic DNS
Enable Dynamic DNS: Check the box to enable DDNS function. It is only necessary when the VoIP
Telephone Adapter is set up behind an Internet sharing device that uses a dynamic IP address and does
not support DDNS.
Server Address: Select a DDNS service from the drop and down arrow.
Hostname: Enter the URL of the system (or NAT) – applied from domain name registration providers (e.g.
www.dyndns.org).
Username or Key/Password or Key: Enter the Login ID and password used to log-in to the DDNS server.
Note: If the VoIP Telephone Adapter is set up under NAT, then enter the hostname in the NAT IP/Domain
that is the same as the Hostname of the DDNS.
D-Link Systems, Inc.
16
DVG-2102S User’s Manual
MAINTENANCE
2-3-4 Diagnostics
Use “Ping” to verify if a remote peer is reachable. Enter a remote IP address and click “Test” to ping the
remote host. The result would be shown on Result Table
MAINTENANCE → Diagnostics
D-Link Systems, Inc.
17
DVG-2102S User’s Manual
STATUS
2-4 STATUS
2-4-1 Device Info
STATUS → Device Info
For System Info, it shows Model Name, Time and Date and Firmware version.
For Network Information, it shows factory default MAC address, IP address, subnet mask, default gateway
and DNS server. If you use DHCP or PPPoE to obtain IP, you will know if the IP address is obtained
through this method. If IP address, subnet mask, default gateway is blank, it means that the VoIP
Telephone Adapter does not obtain IP.
For Hardware, it shows the hardware platform and driver version.
D-Link Systems, Inc.
18
DVG-2102S User’s Manual
STATUS
2-4-2 VoIP Status
STATUS → VoIP Status
For Port Status, it includes if each port registers to Proxy successfully, the last dialed number, how many
calls each port has made since the VoIP Telephone Adapter is start, etc.
2-4-3 Statistics
STATUS → Statistics
Display the information of the last call made. Press Refresh button to get the latest RTP Packet Summary.
D-Link Systems, Inc.
19
DVG-2102S User’s Manual
STATUS
2-4-4 Routing Table
STATUS → Routing Table
The Routing Table stores the information for particular network destination around the VoIP Telephone
Adapter. Press Refresh button to generate the details.
2-4-5 Logout
If setting or parameter has been changed, remember to save the changes before you logout the
configuration menu.
Logout
D-Link Systems, Inc.
20