PPC-5050

15” TFT Panel PC

Ver 1.x

Copyright Notice

This document and product is copyrighted April 2001, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc.

The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products. This manual is subject to change without any notice.

PPC-5050 and ICP are trademark of ICP Electronics Inc.

1

Table of Contents

Chapter 1 Product Information

1.1 General Information

1.2 Product Specifications

1.3 Mechanical Dimension

Chapter 2 System Setup

2.1 The Reverse Side of PPC-5050

2.2 The Side of Front Cabinet

2.3 POS-566/370 CPU Board Installation

2.4 Power Supply Installation

2.5 Drive Disk Installation

2.5.1 FDD Installation

2.5.2 HDD Installation

2.5.3 CD-ROM Installation

2.6 Panel Mounting

2.7 Wall Mounting

2.8 Arm Mounting

Chapter 3 Maintenance

3.1 CPU Board

3.2 Power Supply

3.3 Disk Drives

Appendix A Exploded Diagram

Appendix B Display Interface

Appendix C Touch Panel Controller

2

Chapter 1 Product Information

1.1 General Information

The PPC-5050, 15" LCD TFT Panel PC, takes advantages of modern flat-panel display, POS-566/370 CPU board, drive spaces and power supply for minimum size.

It is an IBM PC/AT compatible computer specially designed to meet the applications for industrial environment.

CPU Board

PPC-5050 is designed for POS-566/370 CPU board. The POS-566/370 board is a

LPX specification board, which equipped with high performance socket 370 Celeron

Pentium III

®

CPU, LCD/CRT and 10/100Mbps Ethernet, designed for the system manufacturers, integrators, or VARs to provide all the performance, reliability, and quality.

LCD Display

The PPC-5050 is equipped with a 15" TFT LCD.

Power Supply

The standard industrial power supply of PPC-5030 is equipped with ACE-915A.

Touch Screen (option)

Dynapro resistive touch screen.

HDD, FDD & CD-ROM

It is suggested to be equipped with one 2.5” internal HDD, one slim FDD, and one slim CD-ROM.

3

1.2 Product Specifications

l Disk Drive Bay: Support one 2.5" HDD, one slim FDD, and one slim CD-ROM. l Best solution for Panel mount man machine interface. l Dimensions : Front Panel: 410mm x 309mm x 9mm (WxHxD)

Cabinet: 383.6mm x 282.6mm x 93.4mm (WxHxD) l LCD Display: 20-pin LCD connector interface to support screen reverse function.

Display Model

Display Type

LCD model

Resolution

Max. colors

Brightness

LCD MTBF

Backlight MTBF

Supply Voltage

NEC

15” TFT color

NL10276BC30-04F

1024x768

24 bits

200 cd/m

2

50,000 hrs

25,000 hrs

5V l Dynapro Touch Screen (option)

Type: Analog Resistive

Resolution: Continuous

Light transmission: Typical value 72%

Surface Hardness: 4H (Test condition: ASTM D3363-92A)

8-wire touch screen

Support driver: Supports DOS, Windows 3.1, 95, 98, NT. l Environmental specifications

Operating Temperature : 0 ~ 50 o

C

Relative Humidity: 5~85% @40 o

C , non-condensing

Vibration: 5 to 17 Hz, 0.1"double-amplitude displacement,

17 to 500 Hz, 1.5 G peak to peak. l Industrial Power Supply: ACE-915AP series Power Supply

High reliability triple outputs switching Power Supply with height 40.6mm only

Standard Power Supply: ACE-915AP

Optional Power Supply: ACE-915A, ACE-815A/ AP and ACE-815T

Operating temperature: -20 o

C to 70 o

C, operating curve will occur at 50 o

C ~70 o

C

Vibration: 10-55Hz at 2G 3 min. period, 30 min. along X, Y, and Z axis

Shock: 10G for 20ms once on each X, Y, and Z axis

4

Safety: meet UL1950/TUV: EN60950

EMI: meet FCC class B /CISPR:EN 55022 class B/CE: Harmonic EN61000-3-2 l Specifications of POS-566 CPU Board:

The POS-566/566L 450MHz K6-3 / Pentium



Processor Multimedia POS

Control SBC provides the following specifications:

• CPU: Pentium

®

MMX up to 233Mhz, AMD

®

K6

®

/K6

®

-2/K6

®

-3 up to

450MHz, IDT C6, Cyrix 6x86MX, etc. Processor

• RAM: 3x DIMM sockets up to 768MB SDRAM

• Cache memory: 512KB Pipelined Burst SRAM on board

• Bus: PCISA bus expansion to support ISA and PCI bus signal

• Chipset: Ali 5, support 100MHz CPU clock

• LCD/CRT Controller: CHIPS 65555 2MB EDO RAM on board

• Support 3.3V or 5V flat panel.

• Support Mono, Color STN, TFT, EL,.. wide range flat panel.

• Optional One Channel or Two Channels LVDS module.

• 10/100Mbps Ethernet Controller: Realtek RTL8139 IEEE 802.u 100

BASE-TX standard Dual Auto-sensing interface to 10MBps or 100MBps networks

RJ45 connector for 10BASE-T and 100BASE-TX

Full duplex capability, full software driver support.

• Creative Sound Blaster 16 compatible and Roland MPU401 UART

Mode compatible

• Four high speed Serial ports : three RS-232C, one RS-232C, or

RS-422/485 Port

• Parallel Ports : Two SPP/EPP/ECP Parallel Ports

• Enhanced IDE Interface :

One 44-pin Header for 2.5” HDD

One 40-pin Header for 3.5” HDD

• PCISA

TM

Bus Expansion to support ISA and PCI bus signal

• Isolated Digital I/O: 4 Digital Inputs and 4 Digital Output channels

5

• IrDA port: Support Serial Infrared (SIR) and Amplitude Shift Keyed

IR (ASKIR) interface.

• Two USB ports: Support dual USB ports for future expansion.

• Watchdog timer: Can be set by 1, 2, 10, 20, 110 or 220 seconds period.

Reset or NMI is generated when CPU does not periodically trigger the timer.

• E

2

Key

TM

Function: A special designed 1Kbit EEPROM (non volatile memory) provided to accept read/ write data by customer’s program. It is useful to store system ID, Password, Critical Data on the board.

• Keyboard connector

• Mouse: PS/2 Mouse Port on-board.

• Power Consumption: +5V/5.5A (AMD K6-2 350MHz, 384MB SDRAM)

+12V: 170mA , -12V : 60mA

• Support ATX and AT power supply

• Operating Temperature : 0

°

~ 60

°

C ( CPU needs Cooler)

• Operating Humidity: 5-95% non-condensing l Specifications of POS-370 CPU Board:

The POS-370 socket 370 Celeron Pentium III



Processor Multimedia POS

Control SBC provides the following specifications:

• CPU: Celeron Pentium III

®

(up to 1GMhz).. Processor

• RAM: 2x DIMM sockets up to 1GB SDRAM.

• Bus: PCI bus expansion to support .

• Chipset: SIS630, support 133MHz CPU clock

• LCD/CRT Controller: On chip SIS300

• Support 3.3V or 5V flat panel.

• Support Mono, TFT, EL... wide one channel that panel.

• Optional One Channel or One Channel LVDS module.

• 10/100Mbps Ethernet Controller: On chip SIS900 LAN BASE-TX standard Dual Auto-sensing interface to 10MBps or 100MBps networks

6

RJ45 connector for 10BASE-T and 100BASE-TX

Full duplex capability, full software driver support.

• On CHIP AC97 SIS 7018

• Four high speed Serial ports : three RS-232C, one RS-232C, or

RS-422/485 Port

• Parallel Ports : Two SPP/EPP/ECP Parallel Ports

• Enhanced IDE Interface : (DMA 66)

Two 40-pin Header for 3.5” HDD

• PCI Bus Expansion to support PCI bus signal

• Isolated Digital I/O: 4 Digital Inputs and 4 Digital Output channe ls

• IrDA port: Support Serial Infrared (SIR) and Amplitude Shift Keyed

IR (ASKIR) interface.

• Five USB ports: Support dual USB ports for future expansion.

• Watchdog timer: Can be set by 1 min.(min.) period.

• Keyboard connector

• Mouse: PS/2 Mouse Port on-board.

• Power Consumption: +5V/6.5A (see POS-370 manual))

• Support ATX and AT power supply

• Operating Temperature : 0

°

~ 60

°

C ( CPU needs Cooler)

• Operating Humidity: 5-95% non-condensing

7

1.3

Mechanical

Dimension

Front Panel: 410mm x 309mm x 9mm (WxHxD)

Cabinet: 382.6mm x 282.6mm x 93.4mm (WxHxD)

8

Chapter 2 System Setup

The PPC-5050, 15" LCD TFT Panel PC, is provided complete kit for your operation.

The following sections of this chapter will help your installation and maintenance.

2.1 The Reverse Side of PPC-5050

The below diagram shows the reverse side of PPC-5050. For maintenance, installation or upgrade, you have to remove the back cover first by unfastening 7 screws as the diagram shown.

Warning:

Before any installation/un-installation, please notice any effects of static electricity.

9

2.2.1 The Reverse Side of the Rear Cabinet

The below figure indicates the reverse side of the rear cabinet.

10

2.2 The Side View of PPC-5050

One FDD and CD-ROM are accessible for your operation on the driver frame.

11

2.3 POS-566/370 CPU Board Installation

To install the POS-566/370 CPU Board, you have to place the board into the cabinet and then fasten it by four screws.

12

2.4 Power Supply Installation

The standard Power Supply for PPC-5050 is ACE-915AP, which has to be fastened to the power bracket by 2 screws , and to be installed in the cabinet by fastening 3 screws as below diagram shown.

Output Spec. at 50°C

Model Input Voltage Rated Load

+5V +12V –12V -5V

Max Output

+5V +12V -12V -5V

ACE-915AP 90V to 264VAC 10A 2.5A 0.1A 0.1A 14A 4A 0.3A 0.2A

13

2.5 Drive Disk Installation

Following sections will introduce you how to install HDD, FDD and CD-ROM.

For the HDD, FDD and CD-ROM are installed in the cabinet, thus you have to open the back cover first if you want to install , upgrade or replace them.

2.5.1 FDD Installation

It’s very easy to install the FDD. First, fasten the FDD to the Floppy Chassis by 4 screws, then fasten it with the Floppy Adapter to the cabinet by 2 screws.

14

2.5.2HDD Installation

To install the HDD, you have to assemble the HDD to the HDD bracket first. Then, fasten the HDD bracket to the cabinet by 2 screws.

15

2.5.2 CD-ROM Installation

To install CD-ROM. You have to assemble the CD-ROM into the bracket, then fasten the CD-ROM Adaptor to the CD-ROM. Finally you have to fasten this unit to the cabinet.

SPACER

16

2.6 Panel Mount ing

PPC-5050 is designed for panel mounting. Before mounting the PPC-5050 into panel, you have to check the cut out dimension first. Then mount it into panel by four supporters. Please refer to diagrams below.

387mm

286mm

17

2.7 Wall Mounting

PPC-5050 is suitable for Wall mount.

TO THE WALL

TO THE WALL

TO THE WALL

TO THE WALL

18

2.8 Arm Mounting

PPC-5050 is not only suitable for panel mounting but also for 75/100mm interface pads for arm mounting; and the specification conform to the proposed VESA standard.

88

75

100

75

100

19

Chapter 3 Maintenance

There are some essential parts you need to know during the operation for the purpose of maintenance or upgrading.

3.1 CPU Board

PPC-5050 is equipped with a POS-566/370 CPU card and a 15" LCD. You need to unfasten the some screws and disconnect interface cables to take the CPU Board out for maintenance or upgrading. Please refer to the section 2.2.

3.2 Power Supply

PPC-5030 is equipped with ACE-915AP series power supply. So you need to unfasten the some screws to take it out for maintenance or upgrading. Please refer to the diagrams of section 2.3.

Warning: Whenever you need to take off a part for either maintenance or upgrading purpose, you should switch off the power supply and unplug the power cord first.

3.3 Disk Drives

PPC-5050 provides one 2.5" HDD, one SLIM FDD, and one SLIM CD-ROM. To maintain or upgrade, please refer to section 2.4.

20

Appendix A Exploded Diagram

1

10

11

8

9

6

7

12

2

3

4

5

ITEM DESCRIPTION

1 BACK COVER

2 HDD BRACKET

3 FDD BRACKET

4 CDROM BRACKET

5 DRIVERS BRACKET

6 CABINET

7 PCI HOLDER

8 LCD BRACKET

9 15” TFT LCD

10 TOUCH PANEL HOLDER

11 TOUCH PANEL

12 FRONT PANEL

PART NO.

41022-006023

41011-014700

41011-014800

41011-014900

41011-014623

41002-005823

41005-007723

41017-010023

23000-000028

41014-011402

48113-333257

43001-002301

21

1

1

1

Q’TY

1

1

1

1

1

1

1

1

1

Appendix B Display Interface

B-1: For POS -566

4

3

5

2

1

B-2: For POS -370

4

3

5

2

1

ITEM DESCRIPTION

1 POS-560/370

2 LVDS-01

3 WIRE CABLE/TOGGLE SW

4 DF14-20S-1.25C/100cm

5 NEC:NL-10276BC30-04F

PART NO.

POS-560(POS-370)

LVDS-01

32100-040400

32000-022200

23000-000028

22

Q’TY

1

1

1

1

1

Appendix C Touch Panel Controller

The optional touch screen provides RS232 interface and the wire diagram of the controller is as the below figure shown.

Touch Panel

Control Board

23