Audiovox AX-500 Installation manual

Model AX-500
Installation Manual
Note: The method of manual override can either be selected to operate from the valet switch or operate as custom
code. Be certain to place a check mark indicating the method used in the box located on the last page of the
owner's manual.
Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin
switch in order to begin the passive arming sequence.
RF Programmable Features :
Feature Selection
1st Door L/UL
1 Chirp
1 Sec.
2 Chirps
3.5 Sec.
3 Chirps
1 Sec L/Dbl. U/L
4 Chirps
Default
350mSuL/1SL 1 Sec.
2nd Accy Lock
Auto Lock On
Auto Lock Off
3rd Accy. UL
Auto UL Dr
Auto UL All
Auto UL Off
4th Headlights
On Arm
On Disarm
On Both
5th Passive Locks
Passive
Active
6th Passive/Active Arm
Passive Arm
Active Arm
7th Voltage Sense
Voltage Sense Hardwire
8th Siren/Horn
Siren/Horn
Siren Only
Horn Only
Siren/Horn
9th Horn Chirp
10mS
16mS
30mS
16mS
Auto Lock Off
Auto UL Off
Off
Both
Active
Active Arm
Hardwire
10th Override Method
Custom Code
Valet
Valet
11th Two Step Unlock
On
Off
Off
12th Chirp Delete From Tx On
Off
Off
To program these selectable features;
Action
Turn ignition on
Press and release the valet switch 3 times
Within 3 seconds, turn ignition Off
First
Then On
Press transmitter Lock button to change
Press transmitter Lock button to change
or
Second Press and release the valet switch
Press transmitter Lock button to change
or
Third
Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
or
Fourth Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
Press transmitter Lock button to change
or
System Response
No response
1 Chirp - LED 1 flash
Short chirp, then long chirp
1 chirp = 1 second door locks
2 chirps = 3.5 second door locks
3 chirps = 1 sec. lock, dbl 1 sec. unlock
2 chirps = auto locks off
1 chirp = auto locks on
3 chirps = auto unlock off
1 chirp = auto unlock drivers door only
2 chirps = auto unlock all doors
3
4
1
2
chirps = headlight output when arming and disarming
chirps = headlight output off
chirp = headlight output when arming
chirps = headlight output when disarming
Revision A: 3-23-04 Changed 1st Door L/UL specification
128-6999A
1 of 8
Fifth
Press and release the valet switch
Press transmitter Lock button to change
or
Sixth
Press and release the valet switch
Press transmitter Lock button to change
or
Seventh Press and release the valet switch
Press transmitter Lock button to change
or
Eighth Press and release the valet switch
Press transmitter Lock button to change
Press transmitter lock button to change
or
Ninth
Press and release the valet switch
Press transmitter Lock button to change
Press transmitter Lock button to change
or
Tenth
Press and release the valet switch
Press transmitter Lock button to change
or
EleventhPress and release the valet switch
Press transmitter Lock button to change
or
Twelfth Press and release the valet switch
Press transmitter Lock button to change
Press and release the valet switch
or
Turn ignition key off
2 chirps = active locks
1 chirp = passive locks
2 chirps = active arming
1 chirp = passive arming
2 chirps = hardwire
1 chirp = voltage sense
1 chirp = siren and horn output
2 chirps = siren output only
3 chirps = horn output only
2 chirps = horn chirp output 16mS
3 chirps = horn chirp output 30mS
1 chirp = horn chirp output 10 mS
2 chirps = valet switch override operation
1 chirp = custom code override operation
2 chirps = 2 step unlock off
1 chirp = 2 step unlock on
2 chirps = chirp delete from transmitter inactive
1 chirp = chirp delete from transmitter active
Exit program mode
Exit program mode
Note: Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps,
or the programming will be terminated.
INSTALLATION OF MAJOR COMPONENTS
Note: This system allows the transmitter to be programmed for single button lock/unlock or separate
button lock/unlock. The receiver is set up as follows:
Channel #1
=
Lock/Unlock/Unlock 2 &Panic
Channel #2
=
If Programmed, Unlock/Unlock 2 & Panic
Channel #3
=
Channel 3 & Alternate Channel 3
Channel #4
=
Channel 4 Output
Channel #5
=
Channel 5 Output (If so Equipped)
During the program routine, if a transmitter button is programmed into receiver channel 2, then the unit will
always have separate lock/unlock from that transmitter.
If during the program sequence receiver channel 1 is programmed, and received channel 2 is skipped over,
as indicated in the transmitted program guide, then the unit will operate as a single button lock/unlock unit
from that transmitter.
It is possible to have one transmitter programmed for single button lock/unlock, and one transmitter programmed for separate button lock/unlock if the customer so desires.
If you inadvertently incorrectly program the transmitter, please read the information on re-prioritizing found
in the transmitter programming guide.
Control Module:
Select a mounting location inside the passenger compartment ( up behind the dash ), and secure using the
two screws provided. The control module can also be secured in place using cable ties.
Do not mount the control module in the engine compartment, as it is not waterproof. You should also avoid
mounting the unit directly onto factory installed electronic components. These components may cause RF
interference, which can result in poor transmitter range or intermittent operation.
Siren:
Select a mounting location in the engine compartment that is well protected from access below the
Page 2
128-6999A
2 of 8
vehicle. Avoid areas near high heat components or moving parts within the engine compartment. To prevent
water retention, the flared end of the siren must be pointed downward when mounted.
Mount the siren to the selected location using the screws and bracket provided.
Hood or Trunk Pin Switch:
A pin switch is included for use in protecting the hood or trunk ( or hatchback ) of the vehicle. The switch
must always be mounted to a grounded, metal surface of the vehicle. It is important to select a location
where water cannot flow or collect, and to avoid all drip gutters on hood and trunk fender walls. Choose
locations that are protected by rubber gaskets when the hood or trunk lid is closed.
The pin switch can be mounted using the bracket provided, or direct mounted by drilling a ¼ “ diameter
mounting hole. Keep in mind that when properly mounted, the plunger of the pin switch should depress at
least ¼ “ when the hood or trunk lid is closed.
Dash Mounted L.E.D.:
A small L.E.D. is included that will serve as a visual indicator of the alarm status. It should be installed in
the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver.
Once a location has been selected, check behind the panel for wire routing access, and to confirm the drill
will not damage any existing components as it passes through the panel.
Drill a ¼ “ diameter hole, and pass the red and blue wires from the L.E.D. through the hole, from the front
of the panel. Firmly press the body of the L.E.D. into the hole until fully seated.
Valet Switch:
Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch
does not have to be concealed, however, concealing the switch is always recommended, as this provides
an even higher level of security to the vehicle.
The valet switch can be mounted to the lower side of the dash by drilling a ¼ “ diameter hole in the selected
location.
Be sure to check behind the dash for adequate clearance for the body of the switch, and to confirm that the
drill will not damage any existing components as it passes through the dash. Route the two pin connector
toward the control module.
Shock Sensor:
Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment,
and mount the sensor using the two screws provided. The shock sensor can also be secured to any fixed
brace behind the dash using tie straps.
Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for use
later in the installation.
WIRING THE SYSTEM
Large 8 Pin Edge Connector:
Red/Purple (5Amp) & Red Fused (15Amp) Wires : + 12 VDC CONSTANT BATTERY SOURCE
This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior
light when a door is opened. It will also detect the switching on of parking or headlamps, and in many cases
will trigger the alarm when a thermostatically controlled electronic radiator cooling fan switches on.
When installing this system into vehicles with electronic “ after fans “, it is recommended you disable the
voltage sense circuit.
In voltage sensing applications, the closer to the battery that the red wire is connected, the less sensitive
the voltage sense circuitry will be. Moving this connection point to the fuse panel will increase the sensitivity, and connecting to the courtesy lamp fuse in the vehicle will provide maximum sensitivity of the voltage
sense circuit. Be certain to set selectable feature # 7 to 1 chirp, Voltage Sense On.
When hardwiring the control module to pin switches at all entry points, the voltage sense circuit must be
disabled.
Orange Wire: 300 mA GROUND OUTPUT WHEN ARMED - N. C. STARTER DISABLE
This wire is provided to control the starter cut relay. Connect the orange wire to terminal 86 of the relay.
Connect relay terminal 85 to an ignition wire in the vehicle that is live when the key is in the on and crank
positions and off when the key is in the off position. (This is where the yellow wire from the alarm should be
connected).
Cut the low current starter solenoid wire in the vehicle, and connect one side of the cut wire to relay terminal
87A. Connect the other side of the cut wire to relay terminal 30.
Note: This is a normally closed starter cut arrangement, and when power is removed from the
security system, the starter disable feature will not operate, allowing the vehicle to start.
Audiovox does not recommend using the Orange wire to interrupt anything but the starting
circuit of the vehicle.
Black w/ White trace Wire: Entry Illumination Ground Output
This wire provides a 30 second ground output (300 mA Max) whenever the remote is used to disarm the
alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This
wire should be connected to an external relay and wired to the vehicles interior entry lighting whenever the
optional Interior Illumination circuit is desired. See Wiring Diagram for details.
Page 3
128-6999A
3 of 8
Red/White Wire: DELAYED 300 mA PULSED OUTPUT / CHANNEL 2
This wire pulses to ground via an independent RF channel from the keychain transmitter. This is a transistorized, low current output, and should only be used to drive an external relay coil.
WARNING: Connecting the white/blue wire to the high current switched output of trunk release circuits,
some remote start trigger inputs, will damage the control module.
Connect the white/blue wire to terminal 86 of the AS - 9256 relay (or equivalent 30 A automotive relay), and
wire the remaining relay contacts to perform the selected function of channel 2.
Brown Wire: POSITIVE OUTPUT TO SIREN
Route this wire through a rubber grommet in the firewall, and to the siren location.
Connect this wire to the positive wire of the siren. Secure the black ground wire of the siren to chassis
ground.
Black Wire: CHASSIS GROUND
Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse this wire with the thin black
antenna wire that exits the control module independently.
White Wire: + 12 VDC PULSED PARKING LIGHT OUTPUT (15 AMP MAX)
This wire is provided to flash the vehicle’s parking lights. Connect the white wire to the positive side of one
of the vehicle’s parking lights.
Wiring The 11 Pin Mini Edge Connector:
White/Blue Wire: 300MA PULSED OR LATCHING OUTPUT / CHANNEL 4
This wire latches to ground via an independent RF channel from the keychain transmitter. This is a transistorized, low current ( 300 mA ) output, and should only be used to drive an external relay coil.
This wire provides an immediate ground signal, and stays at ground for as long as the button(s) on the
keychain transmitter remains pressed.
WARNING ! Connecting the purple/black wire to the high current switched output of trunk release
circuits will damage the control module.
Connect the purple/black wire to terminal 86 of the AS 9256 relay (or an equivalent 30 Amp automotive
relay ), and wire the remaining relay contacts to perform the selected function of channel 4.
White/Green Wire: Activation Output (Dbl. Push Required)
This wire is controlled from the transmitter button programmed to the receiver's channel 2. By double
pressing this the transmitter button, this output will become active for 1 second. This is a transistorized,
low current (300 mA) output, designed to provide an output only when the transmitter is intentionally
operated, such as is the case with remote start add on modules. If you require more than 300mA drive from
this output, you must drive an external relay coil, and arrange the relays contacts to preform the specified
function.
NOTE: Pressing the transmitter button, then immediately pressing and holding it will cause this output to
be active as long as the transmitter button is depressed.
Brown/Black Wire: 300 mA Horn Output
The brown/black wire is provided to beep the vehicle’s horn. This is a transistorized low current output, and
should only be connected to the low current ground output from the vehicle’s horn switch.
If the vehicle uses a + 12 VDC horn switch, then connect the black w/ white trace wire to terminal 86 of the
AS 9256 relay ( or an equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12
VDC battery source. Connect relay terminal 87 to the vehicle’s horn switch output, and connect relay
terminal 30 to a fused + 12 VDC battery source.
Vacant Cavity In Connector: Not Used
Blue Wire: ( - ) INSTANT TRIGGER ZONE
This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin
switches.
Green Wire: - DOOR TRIGGER
If the vehicle’s courtesy light switches have a ( - ) ground output when the door is opened (GM and most
Imports), you must connect this wire to the negative output from one of the door switches.
WARNING: Do not use the brown wire if the vehicle has + 12 volt output type door switches.
(see Purple Wire).
Note for vehicles with interior delay lighting see programming under title "Completing The Installation".
Purple Wire: + DOOR TRIGGER
If the vehicle’s door courtesy light switches have a + 12 volt output when the door is opened (most Fords
and some Imports ), you must connect this wire to the positive output from one of the door switches.
WARNING: Do not use the purple wire if the vehicle has ground output type door switches.
( see Brown Wire ).
Note for vehicles with interior delay lighting see programming under title "Completing The Installation".
Page 4
128-6999A
4 of 8
Yellow Wire: + 12 VDC IGNITION SOURCE
Connect this wire to a source that is live when the key is in the on and crank positions. Be sure that this
source is off when the key is in the off position.
Green/Orange Wire: Low Current (-) Ground Headlight Output
The green/orange wire is provided to operate the optional headlamp illumination feature of the system. This
is a low current (300mA) output and must be connected to an external relay to control the high current
switching circuit of the vehicle's headlamps. To use this option, Connect this wire to terminal # 86 of a P&B
VF45F11 relay or equivalent. Connect Terminals #85 and # 30 to a fused + 12 Volts source with a current
capability equal to or in excess of the factory headlamp fuse. Connect terminal # 87 of the relay to the
switched + 12 volt wire feeding the vehicle's headlamp circuit.
NOTE: For ground switched headlamp circuits, Connect the green/orange wire to terminal # 86 of a P&B
VF45F11 relay or equivalent. Connect Terminal #85 to a fused + 12 Volts source. Connect terminal
# 30 to a clean chassis ground. Connect terminal # 87 to the ground switched headlamp control
wire in the vehicle.
Blue/White Wire: (-) Instant Trigger Zone 1
This is a instant on ground trigger input intended for the connection of optional triggering devices. The
ground trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be
connected to this trigger input wire.
Purple/Black Wire: 300MA PULSED OR LATCHING OUTPUT / CHANNEL 5
The light blue/green wire pulses to ground via an independent RF channel from the keychain transmitter.
This is a transistorized, low current output, and should only be used to drive an external relay coil.
WARNING: Connecting the gray/black to the high current switched output of trunk release circuits, some
remote start trigger inputs, will damage the control module.
Connect the gray/black to terminal 86 of the AS - 9256 relay (or equivalent 30 A automotive relay), and wire
the remaining relay contacts to perform the selected function of channel 5.
2 Pin White Connector: DASH MOUNTED L.E.D.
Route the red and blue wires in the 2 pin white connector from the L.E.D. to the control module, and plug
it into the mating white connector on the side of the module.
4 Pin White Connector: SHOCK SENSOR
Route the red, black, blue, and green wires in the 4 pin white connector from the shock sensor to the
control module, and plug one end into the shock sensor, and the other end into the mating white connector
on the side of the module.
Green, Blue, Blue/Red 3 Pin White Connector: Door Lock Outputs
The Green and Blue wires will provide either a pulsed ground output to the factory door lock control relay,
or a pulsed + 12 volt output to the factory door lock control relay. In either case, the maximum current draw
through these outputs must not exceed 300 mA. The Blue/Red wire will provide a pulsed ground only, and
will only provide an output when the unlock button of the transmitter is pressed a second time after a first
unlock command was issued. This is used for second step unlock or all doors unlock in a two step circuit.
In this arrangement, Green, or Blue is used to control the drivers door unlock relay, and the Blue/Red will
be used to control unlock of all other doors.
3 Wire Ground Switched Single Step Door Locks
In this application, the green wire provides a ground pulse during arming, or the pulsed ground lock
output. Connect the green wire to the wire that provides a low current ground signal from the factory door
lock switch to the factory door unlock control relay.
The blue wire provides a ground pulse during disarming, or the pulsed ground unlock output. Connect
the blue wire to the wire that provides a low current ground signal from the factory door unlock switch to the
factory door unlock control relay.
Red/Black Not Used.
3 Wire Ground Switched 2 Step Door Locks
In this application, the green wire provides a ground pulse during arming, or the pulsed ground lock
output. Connect the green wire to the wire that provides a low current ground signal from the factory door
lock switch to the factory door lock control relay.
The blue wire provides the first ground pulse during disarming, or the drivers door pulsed ground
unlock output. Connect this wire to the drivers door unlock relay that requires a low current ground
signal to unlock only the drivers door. If the vehicle does not have a sperate drivers door relay, one will have
to be added. Locate the drivers door unlock motor wire and cut it at a convenient location to allow wiring of
an optional relay. Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect
the vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the blue wire of the 3
pin harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay added to
Page 5
128-6999A
5 of 8
a fused constant + 12 volt source. Most vehicles door lock/unlock motor legs rest at ground, and switch +12
volts to the door lock/unlock motor legs for operation, if this is the case in the vehicle you are working on,
connect the remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle door
lock/unlock motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect he
remaining terminal, 87, to chassis ground.
The Blue/Red wire provides a pulse ground output when the unlock button of the transmitter is pressed a
second time after disarming. Connect the Blue/Red wire to the wire that provides a low current ground signal
from the factory door unlock switch to the factory door lock control relay.
3 Wire Positive Switched Door Locks
In this application, the green wire provides a positive pulse during disarming, or the pulsed + 12 volt
unlock output. Connect the green wire to the wire that provides a low current positive signal from the factory
door unlock switch to the factory door unlock control relay.
The blue wire provides a positive pulse during arming, or the pulsed + 12 volt lock output. Connect the blue
wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door
lock control relay.
3 Wire Positive Switched 2 Step Door Locks
The blue wire provides a positive pulse during arming, or the pulsed + 12 volt lock output. Connect the blue
wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door
lock control relay.
The green wire provides a positive pulse during disarming, or the drivers door pulsed positive unlock
output. Connect this wire to the drivers door unlock relay that requires a low current positive signal to
unlock only the drivers door. If the vehicle does not have a separate drivers door relay, one will have to be
added. Locate the drivers door unlock motor wire and cut it at a convenient location to allow wiring of an
optional relay. Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect the
vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the green wire of the 3 pin
harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay added to
chassis ground. Most vehicles door lock/unlock motor legs rest at ground, and switch +12 volts to the door
lock/unlock motor legs for operation, if this is the case in the vehicle you are working on, connect the
remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle door lock/unlock
motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect he remaining
terminal, 87, to chassis ground.
The Blue/Red wire provides a pulse ground output when the unlock button of the transmitter is pressed a
second time after disarming. Because the vehicle you are working on requires a positive pulse from the
factory door lock switch to the factory door lock control relay, you will have to add a relay to invert the output
polarity of this wire. Connect the Blue/Red wire to terminal 86 of the optional added relay. Connect terminal
85 & 87 to a fuse + 12 volt source. Connect terminal 30 to the low current door unlock wire from the factory
door switch to the door unlock control relay.
Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt
Door Lock Control Circuits
These applications require the use of additional components which may include relays, fixed resistors, or for
convenience, the AS 9159 Door Lock Interface. Consult your technician or refer to the technical hotline
provided by your sales representative for information on your particular vehicle for properly connecting to
these types of circuits.
4 Pin Upgrade Telematic Module:
Red = + 5 Volts
Black = Ground
White = Data TX
Yellow = Data RX
Connect the 4 pin harness found in the Telematic one way module kit to the mating port on the PTUGM.
NOTE: If using the TWO WAY Telematic module, only Ground, TX, and RX are used on this port, the + 12 volt supply
for the two way module must be sourced separately or the unit will not operate.
COMPLETING THE INSTALLATION
NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has
delay interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with
this type of interior light, we suggest you learn the interior light delay.
To learn the light delay, start with all doors closed:
(1) Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system.
The LED turns on solid to confirm the system entered the learn mode.
(2) Immediately open and close the door of the vehicle to initiate the dome delay.
The unit will monitor the door trigger input Positive, (Purple), and Negative, (Brown) when active.
When the dome light turns off, the unit will add 2 seconds then exit the learn mode.
(3) The LED will begin flashing the Armed indication indicating the unit has exited the learn mode and is
armed.
Page 6
128-6999A
6 of 8
Antenna Wire: Be sure to extend the thin black antenna wire to it’s full length, and cable tie into place
where it cannot be damaged. Avoid wrapping this wire around major, high current wire looms.
Adjusting the Shock Sensor: If used, the sensitivity of the pre - detect circuit is automatically set 30% less
sensitive than the full trigger circuit.
Using a small screwdriver, gently turn the adjustment screw fully counterclockwise. (DO NOT over turn this
screw. Maximum rotation for this adjustment is 270°). Close the hood and trunk lids, and arm the alarm.
Wait 6 seconds for the accessories trigger zone to stabilize, then firmly strike the rear bumper with the side
of a closed fist considering the amount of force required to break a window.
CAUTION: Never perform this test on the vehicle’s glass, as you may break the window.
Turn the adjustment screw clockwise (increasing sensitivity) about ¼ turn and re-test. Repeat this
procedure until the alarm sounds. Ultimately, one firm strike to the rear bumper will cause the alarm to emit
pre-detect warning tones.
WARNING ! Setting the sensitivity too high can cause false alarms due to noise vibrations from passing trucks
and heavy equipment. To decrease sensitivity, turn the adjustment screw counter clockwise.
Wire Dressing: Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape.
Secure these looms along the routing using cable ties. This will ensure that the alarm wires are not damaged
by falling onto hot or sharp moving surfaces in the vehicle.
Operation: Take a few moments to check off the appropriate option boxes in the owner’s manual, and to
fully explain the operation of the system to your customer.
Place the Valet Switch Tag and or the Remote Start Control Switch Tag on their respective switches and
point these out to the customer.
11 Pin Harness
White/Blue
White/Green
Brown/Black
Vacant
Blue
Green
Purple
Yellow
Green/Orange
Blue/White
Purple/Black
(-) Channel 4 Output Pulsed or Latched 300mA
(-) Activation Output (Output With Double Push Of Trunk Pop Button) 300mA
(-) Horn Honk Output 300mA
No Connection
(-) Trunk Pin Instant Trigger Input (Shunted During Trunk Pop)
(-) Door Trigger Input
(+) Door Trigger Input
(+) 12V Ignition Input
(-) Headlight Control Output 300mA
(-) Negative Instant Trigger Input
(-) Channel 5 Output Pulsed 300mA
Red/Purple
Orange
Black/White
Red/White
Brown
Black
White
Red
8 Pin Harness
(+) 12 V Constant Power 5A
(-) Starter Disable Output / Ground when Armed Output 300mA
(-) Domelight Supervision Output 300mA
(-) Trunk Pop Output Pulsed 300mA
(+) Siren Output
(-) Chassis Ground
(+) 12 V Parking Light Output
(+) 12 V Constant Power Input 15A
Green
Blue
Blue/Red
3 Pin Lock Harness
(+) Unlock / (-) Lock 300mA max
(+) Lock / (-) Unlock 300mA max
(-) 2nd Unlock 300mA max
4 Pin Telematic Harness
White
Data Transmit
Yellow Data Receive
Black
Ground
Red
(+) 5 V
4 Pin Shock Sensor Harness
Red
(+) 12 Volt Constant
Black
(-) Ground When Armed
Green
(-) Full Alarm Trigger Input
Blue
(-) Warn Away Trigger Input
Page 7
128-6999A
7 of 8
© 2003 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788
128-6999A
128-6999A
8 of 8