Craftsman 139.53491SRT Owner`s manual

SEARS
OWNER'S
MANUAL
Model No.
139.53491SRT
For Residential Use
CRRFTSMRN
Only
1/2 HP
GARAGE DOOR OPENER
Caution:
Read and follow all
• Safety Precautions
safety rules and
operating instructions
before first use of this
product.
• Adjustment
• Care and Maintenance
• Operation
Fasten the manual
near the garage door
after installation.
Complies withUL325
regulations effective
January 1, 1993
• Assembly
• Installation
• Troubleshooting
• Parts List
/'1111 _
Sears,
Roebuck
and Co., Hoffman
Estates,
IL 60179 U.S.A.
Contents
Safety alert symbol review ............................................
2
Complete the safety reversing sensor installation .....22
Safety information, precautions, tools .......................... 3
Install the lights and lens ..........................................
Testing your garage door for binding & balance .......... 3
Attach the emergency release rope and handle ......... 23
Carton inventory ...........................................................
4
Fasten the door bracket (sectional door) ................... 24
Hardware inventory .......................................................
5
Illustration of sectional door installation ..................... 6
Fasten the door bracket (one-piece door) .................. 25
Illustration of one-piece door installation ..................... 7
23
Connect door arm to trolley (sectional door) ............ 26
Connect door arm to trolley (one-piece door) ........... 27
Assembly section - pages 8 - 11
Assemble the rail ........................................................
Adjustment
8
Travel limit adjustments ............................................
28
Fasten rail to power unit ............................................
10
Force adjustments .....................................................
29
Install the trolley .......................................................
Attach the rail brackets .............................................
10
11
Test the safety reversing sensor ................................
30
Installation section - pages 12 - 27
section - pages 28 - 30
Test the safety reverse system ..................................
30
Operation safety instructions ......................................
31
Installation safety instructions ..................................
Determine the header bracket location
11
Care of your opener ....................................................
Maintenance schedule .................................................
31
31
Sectional door .........................................................
12
Operation of your opener ............................................
32
One-piece door ........................................................
Install the header bracket ..........................................
13
14
Receiver & remote control programming
Troubleshooting
................... 33
..........................................................
34
Attach the rail to the header bracket ......................... 15
Repair parts, rail assembly ..........................................
36
Safety reversing sensor information ......................... 16
Repair parts, installation .............................................
36
Install the safety reversing sensor ............................. 17
Repair parts, power unit ..............................................
Accessories .................................................................
37
38
Position the opener ....................................................
19
Hang the opener ........................................................
20
Install the door control and connect all wires ........... 21
Index ...........................................................................
39
How to order repair parts ............................................
40
Electrical requirements
Warranty ......................................................................
40
Start
by reviewing
.............................................
these
important
safety
22
alert
symbols:
When you see these Safety Symbols on the following pages, they will alert you to the possibility
or death if you do not comply with the corresponding
instructions.
The hazard may come from
mechanical
or from electric shock. Read the instructions
carefully.
Mechanical
of serious
something
injury
Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage to your
garage door and/or the garage door opener if you do not comply with the corresponding
instructions. Read the
instructions carefully.
iiii
iiii iiii
iiii
This garage door opener is designed and tested to offer safe service provided it is installed,
and tested in strict accordance with the safety instructions contained in this manual.
operated,
maintained
Safety Information
and Precautions;
An unbalanced garage door might not re verse when
requiredand someoneunder thedoor couldbe seriously
injuredor killed.
If yourgaragedoorbinds,sticksor is out of balance,call
for professionalgaragedoor service.Garagedoors,door
springs,cables,pulleys,brackets,and theirhardwareare
under extreme tensionand can cause serious injury or
death. Do not try to loosen, move or adjust them
yourself!
Ropes left on a garage door could cause someone to
become entangled and killed. Remove all ropes
connectedto the door beforeinstallingand operatingthe
opener.
Tools
To avoiddamageto the garagedoor and opener,disable
locks before installingand operatingthe opener. Use a
woodscrewor nail to hold locksin the "open" (unlocked)
position.
Operationat other than 120V 60 Hz will cause opener
malfunctionand damage.
Identify the type and height of your door, any special
conditions that exist, and any additional materials that
may be required. Refer to pages 6 and 7.
Test Your Door for Balance
Before you begin, complete
sure your door is balanced,
binding:
the following test to make
and is not sticking or
Sectional Door
• Lift the door about halfway as shown. Release the door.
It should stay in place, supported entirely by its springs.
• Raise and lower the door to see if there is any binding or
sticking.
One-Piece Door
During assembly, installation and adjustment of the opener, instructions will call for tools shown below.
Pencil
Level
Hack
Tape Measure
Saw
Wire Cutters
Drill
3/16", 5/16" and
5/32" Drill Bits
Stepladder
Pliers
Screwdriver
Claw Hammer
1/2" x 7/16" Box Wrench
Carton Inventory
Your garage door opener is packaged in one carton which contains the power unit and all parts illustrated below. If anything
is missing, carefully check the packing material. Parts may be "stuck" in the foam. KEEP THE FOAM INTACT (see page
10). Hardware for assembly and installation is shown on page 5.
Sprocket
Coupling
Three-Function
Remote Control
with Visor Clip (2)
Standard
Control Console
Rail Support
Braces_
Rail
Assembly
Light Lens
2-Conductor Bell Wire
White & White/Red
I__)
0._
I_
6/
Header/Rail
Brackets
_1_
iq?
©
iq,
Door Bracket
Door Bracket Plate
Header
Straight Door
Arm Section
Bracket
Hanging Brackets
Curved Door
Arm Section
I
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with attached
2-Conductor White & White/Black Bell Wire
Safety Reversing Sensor
Mounting Bracket
With Square Holes (2)
"C" Wrap (2)
Safety Reversing Sensor
Mounting Bracket
With Slot (2)
Hardware
Separate all hardware from the packages in the rail carton and the opener carton and group as shown below, for
the assembly and installation procedures.
Assembly
lllllllll/
Bolt
1/4-20xl-3/4"
]
]
]
1/4" - 20 x 5/8"
Hex Screw (4)
(8)
laglSclew]
5/16"-9xl-5/8"
]
@
RllllllID
Installation
_
Hardware
I _
Lock Nut
1/4"-20 x 7/16 (12)
Sprocket
Coupling
Sleeve
Hardware
O
Handle
(2)
Ring
Fastener (3)
Nut 5/16"-18 (6)
111111111111 >
Lag Screw
5/16"-18xl-7/8"
(2)
Hex Screw
5/16"-18x7/8"
(4)
Carriage Bolt
5/16"-18x2-1/2"
(2)
6ABxl"
Insulated
Staples (10)
(2)
Rope
oH
Clevis Pin
5/16"x2-3/4" (1)
Lag Screw
1/4x1-1/2" (4)
Hex Screw
1/4-20xl -1/2" (2)
5/16" (6)
Dry Wall Anchors (2)
o]
Safety Reversing
Lock Washer
Clevis Pin
5/16"x1" (1)
Sensor
Installation
Clevis Pin
5/16"x1-1/4"
(1)
Hardware
©
Carriage Bolt
1/4"-20xl/2"
(4)
Screw
#10-32x3/8"
(4)
Lock Nut
1/4"-20 x 7/16 (4)
Lock Nut
#10x32 (4)
Wing Nut (2)
Insulated
Staples (20)
SECTIONAL
Door Installation
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
Horizontal and vertical
is needed for lightweight
(fiberglass, steel, aluminum, door
See page 24 for
FINISHED CEILING
Support bracket &
fastening hardware
is required.
See page 20.
reinforcement
garage doors
with glass panels, etc.).
details.
Header Wall
Extension Spring
OR
Torsion Spring
Access
Door
O
Safety
Reversing
Sensor
Floor must be level
across width of door
Safety Reversing Sensor
Closed Position
Header
Bracket
Based on your particular requirements, there are several
installation steps which might call for materials and/or
hardware not included in the carton.
Rail
_/
Bracket
• Step 6, page 20 - Do you have a finished ceiling in your
garage'? If so, a support bracket and additional fastening
hardware may be required.
• Step 12, page 24 - Do you have a steel, aluminum,
fiberglass or glass panel door'? If so, horizontal and
vertical reinforcement is required.
• Look at the garage door where it meets the floor. It
must close on the floor all the way across. Otherwise,
the safety reverse system may not work properly. See
page 30. Floor or door should be repaired.
Trolley
_'(o3Y"Door / /
Spring
lJ I
Straight
Door
• Step 4, page 17 - Alternate floor mounting of the safety
reversing sensor will require hardware not provided.
................................
Garage
• Step 1, page 12 - Look at the wall or ceiling above the
garage door. The header bracket must be securely
fastened to structural supports.
• Safety reversing sensor, page 16 - Depending upon
garage construction, wood blocks may need to be
fastened to mounting locations before sensors are
installed.
Rail Assembly
Header
Wall
_
/?/
Emergency
I
J.
__._7/
I_
Fpe&Han--oReleasedle
Curve_--
_1 Door "Door
Garage -Door
_
Bracket
Arm
• The opener can be installed within 2 feet of the left or
right of the door center if there is a torsion spring or
center bearing plate in the way of the header bracket or
door bracket area. [[):our door has extension springs',
the opener must be installed in the center of the dooe
See pages 12 and 24.
• Do you have an access door in addition to the garage
door'? If not, Model 53702 Emergency Key Release is
required. See page 38.
You may find it helpful to refer back to this page as
you proceed with the installation of your opener.
ONE-PIECE
Door Installation
Before you begin, survey your garage area to
see whether any of the conditions below apply
to your installation.
FINISHED CEILING
Support bracket
& fastening
hardware is required.
See page 20.
Header
Wall
One-Piece
Door without
Track
Closed Position
Rail
Bracket
Access Door
Rail Assembly
O
Garage
Door
Door
Arm
Safety Reversing
Sensor
Ga _ between floor and bottom of
door must not exceed 1/4",
Safety Reversing Sensor
Based on your particular requirements, there are several
installation steps which might call for materials and/or
hardware not included in the carton.
• Step 1, page 13 - Look at the wall or ceiling above the
garage door. The header bracket must be securely
fastened to structural supports.
• Step 6, page 20 - Do you have a finished ceiling in your
garage'? If so, a support bracket and additional fastening
hardware (not supplied) may be required.
• Safety reversing sensor, page 16 - Depending on garage
construction, wood blocks may need to be securely
fastened to mounting locations before sensors are
installed.
• Step 14, page 17 - Alternate floor mounting of the
safety reversing sensor will require hardware that is not
provided.
• Step 12, page 25 - Generally, a one-piece door does not
require reinforcement. If your door is lightweight, you
can refer to the information relating to sectional doors
on page 24.
:_if__ust
_
_dih
Reversing Sensor
Closed Position
• The gap between the bottom of the garage door and
the floor cannot exceed 1/4". Otherwise, the safety
reverse system may not work properly. See page 30.
The floor or the door should be repaired.
Rail
Header
Wall
• Step 12, page 25 - Depending on your door's
construction, you might need additional mounting
hardware for the door bracket.
• Do you have an access door in addition to the garage
door'? If not, Model 53702 Emergency Key Release is
required. See page 38.
Reversing
Sensor
Sensor
be level
ofdoor
Trolley
Header
Bracket
--
Door
_ Curved
o
z.-,_..._-,,-
_/_
I
Rail Assembly
O000000lO000
- Door
°°::;j:°°°'J
el
Bracket
_ralgm
Door
Arm
I
I-I--
EmergencyReleas
Rope & Handle
You may find it helpful to refer back to this page as
you proceed with the installation of your opener.
ASSEMBLY
SECTION" PAGES 8 - 11
Assembly Step 1
Assemble
To avoid installation difficulties, do not run the garage
door opener until instructed to do so.
the Rail
Straight
Door Arm
Rail
Support
Braces
Extend
End Rails
Outward
Remove
Cardboard Packing
Center
Rail
--
Trolley
Rail Assembly
Carton
Rail Assembly
Hardware Bag
(
_ _"
Remove
Cardboard Packing
Rack
Chassis Assembly
Hardware Bag
Extend
End Rails
Outward
1. Turn the opened rail carton upside down, emptying its
contents onto a level work surface.
2. Unfold the rails, taking care to avoid kinking the screw
rod joints.
3. Rotate the rail sections so that the flat side is down and
the screw side is up for all three lengths. Keep it clean
and free of debris while you are working.
Sprocket
End Rail
Rail
Sprocket
Center Rail
Trolley Rack
CAUTION: During assembly, awdd pulling the rail
section housing the trolley rack away from the screw
rod. The rack is facto1T set about 9"from the end of the
screw rod to the center of the rack.
If the plastic liner slides part way out during assembly,
simply push it back in.
DoorEnd
Rail
Assembly Step 1 (Continued)
Assemble
the Rail
4. Beginning with the sprocket end, straighten the two
rail sections so that the screw rod is in a straight line at
the joint. (Avoid handling the joints, which may have
sharp edges.)
5. Carefully slide the pins at the top edge of the rail into
the openings on the adjacent rail. It is essential that
the rail assembly be on a level smfaee to achieve
proper alignment and to aw_id damage to the pins.
6. Insert two 1/4"-20xl-3/4" bolts through the center
holes of a brace, and place its open length against the
rail at this joint, aligning the holes as shown. Position
another brace on the opposite side of the rail over the
bolts, add 1/4"-20 lock nuts, and hand tighten. Insert
two additional bolts and hand tighten.
7. Keeping the rail straight and on a level surface, grasp
the screw rods on each side of the remaining joint and
pivot into a straight line. Repeat steps 5 and 6.
8. With a 7/16 wrench, tighten bolts til snug, working
from the center holes of the braces to those further
from the joints. Do not overtighten.
Sprocket
Rail
Support
Brace
Alignment
Hole
Lock
Nuts
Rail
Support
)__
Brace
Lock
Nuts
-- -
Center Rail
Door End
_"
1/4x20x 1-3/4"
Bolts
Slide End
Rails Towards
Center Rail
Hardware Shown Actual Size
D
illllllll}
Bolt
1/4-20xl-3/4"
(8)
_ _--_'---_
Bolts
Alignment
_
Slide End
Rails Towards
Center Rail
1/4x2Ox1-3/4"
Rail Pin
@- -
@
1/4"-20
Lock Nut
End
Assembly Step 2
Fasten the Rail To the Power Unit
and Install the Trolley
NOTE: To aid in assembly
and installation,
replace
the foam packing around the power unit. Remove it
after Installation
Step 5.
• Working on a level surface, align the rail assembly with
the power unit, as shown.
Rail/Power Unit
Bracket
Lock Nuts
1/4"-20
• Slip the coupling over the rail sprocket.
/
I
• Slide the rail through the power unit bracket until the
coupling fits securely over the power unit sprocket.
Power Unit
Sprocket
//
• Align the two screw holes in the rail with those in the
power unit bracket. Insert two 1/4"-20x5/8" hex screws
and lock nuts. Tighten securely with a 7/16" socket
wrench.
/
J
_"
Hex Screws
1/4"-20x5/8"
Foam Packaging
Rail
Assembly
Hardware Shown Actual Size
1/4" - 20 x 5/8"
1/4"- 20
Lock Nut
D;Ix,sI:;,D
@
Trolley
As illustrated
above, slide the trolley onto and along the
bottom of the rail until it snaps firmly in place. Be certain
to install #facing
correctly: the trolley release arm must
be horizontal
(lock position),
with its arrow pointed
away from the power unit.
10
Assembly Step 3
Attach
the Rail Brackets
1/4"-20
Lock Nuts
Rail
Brackets
• Align rail brackets to end of rail assembly, as shown.
• Insert two 1/4"-20 x 5/8" hex screws and lock nuts.
Tighten securely with a 7/16" socket.
Hardware Shown Actual Size
1/4" - 20 x 5/8"
1/4" - 20
Lock Nut
1/4"-20x5/8
Hex
Screws
You have now finished assembling your garage door opener. Please read the following
before proceeding to the installation section:
warnings
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTALLATION
INSTRUCTIONS
2. Install only on a properly balanced and lubricated
garage door. An improperly
balanced door may not
reverse and could result in severe injuly or death. Repairs
to cables, spring assemblies
and other hardware
must be made by a professional
service person before installing
opener.
3. Disable all locks and remove all ropes connected to the garage door before installing
connected to a garage door can cause entanglement and death.
4. If possible, install door opener 7 feet or more above floor with the emergency
feet above the floor.
5. Do not connect the opener to power source until instructed
the opener. Ropes
release handle mounted 6
to do so.
6. Locate the Door Control within sight of the door at a minimum
cannot reach and away from all moving parts of the door.
height of 5 feet where small children
7. Install the User Safety Instruction Label on the wall adjacent to the control button and the Maintenance
Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a one-inch high
object or a 2x4 laid flat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry
clothing can be caught in the mechanism of the garage door or the opener.
11
or loose
INSTALLATION
Installation
Determine
SECTION"
PAGES 12-
27
Step 1
Header
Bracket
Location
If the header bracket is not rigidly fastened to a
structural support on the header wall or ceiling, the
safety reverse system may not work properly (see
page30). The doormightnot reverse whenrequired,and
couldcauseseriousinjuryor death.
Installation procedures vary according to garage
door types. Follow the instructions which apply to
your door.
Vertical
Guideline
Header
Wall
The garagedoor springs,cables,pulleys,bracketsand
theirhardwareareunderextremetension.Do notattempt
to loosen, move or adjust them yourself. Serious
personal injury or death could result.
Call for
professionalgaragedoor service.
Finished
Ceiling
2x4
Structural
SECTIONAL
Door or
ONE PIECE Door with Track
• Close the door and mark the inside
vertical centerline of the garage door.
• Extend the line onto the header wall
above the door.
Remember, you can fasten the header
bracket within 2 feet of the left or right
of the door center only if a torsion
spring or center bearing plate is in the
way; or you can attach it to the ceiling
(refer to page 14) when clearance is
minimal. (It may be mounted on the
wall upside down if necessary, to gain
approximately
1/2".)
If you need to install the header bracket on
a 2x4 (on waft or ceiling), use lag screws
(not supplied) m securelyJasten the 2x4 m
structural supports as shown here and on
page 13.
Ceiling
Header
Wall
,,............
3"
• Open your door to the highest point of
travel as shown. Draw an intersecting
horizontal line on the header wall 3"
above the high point. This height will
provide travel clearance for the top edge
of the door.
Track
I
Highest Point
of Travel
Highest Point
of Travel
Door
Door clearance brackets are available
for sectional doors when headroom
clearance is less than 2". See accessory
page 38.
Proceed
Sectional door
with curved track
One-piece door
with horizontal track
12
to Step
2, page
14.
ONE-PIECE
Read
the Safety
Instructions
on page
Door Without
12. They
also apply
Track
to doors
without
tracks.
Unfinished
• Close the door and mark the inside
vertical centerline of your garage door.
Extend the line onto the header wall
above door.
Header Wall
Ceiling
Vertical
Centerline
2x4
Su
If headroom clearance is minimal, you
can install the header bracket on the
ceiling. See page 14.
• IJ_vou need to install the header
bracket on a 2x4 (on wall or ceiling),
use lag screws (not supplied) to
securely fi_sten the 2x4 m structural
supports as shown.
• Open your door to the highest point of
travel as shown. Measure the distance
from the top of the door to the floor.
Subtract the actual height of the door.
Add 8" to the remainder. (See
Example).
• Close the door and draw an
intersecting horizontal line on the
header wall at the determined height.
If the total number of inches exceeds
the height available in your garage,
use the maximum height possible, or
refer to page 14 for ceiling
installation.
Proceed
to Step
2, page
Vertical
Centerline of
Garage Door
OPTIONAL CEILING MOUNT
FOR HEADER BRACKET
Header Wall
Highest Point
of Travel
Highest Point
of Travel
E_
,g
t
t C3
Jamb
Hardware
14.
EXAMPLE
Distance from top of door
(at highest point of travel) to floor .............
Actual height of door ......................
Add
Header
Wall
Door
One-piece door without track
jamb hardware
Remainder
2x4
Header Su
................................
....................................
Bracket height on header wall ...............
92"
-88"
4"
+8"
= 12"
(Measure UP from top of CLOSED door.)
13
One-piece door without track
pivot hardware
Installation
Install
Step 2
the Header
Bracket
You can attach the header bracket either to the
wall above the garage door, or to the ceiling.
Follow the instructions which will work best for
your particular requirements.
Fastening
the Header
Bracket
Fastening the Header Bracket to the Ceiling
to the Wall
• Center the bracket on the vertical guideline with the
bottom edge of the bracket on the horizontal line as
shown (with the arrow pointing toward the ceiling).
• Extend the vertical guideline onto the ceiling as shown.
• Center the bracket on the vertical mark, no more than 6"
from the wall. Make sure the arrow is pointing toward
the wall. The bracket can be mounted flush against the
ceiling when clearance is minimal.
• Mark either set of bracket holes (do not use the holes
designated for ceiling mount). Drill 3/16" pilot holes
and fasten the bracket securely to a structural support
with the hardware provided.
• Mark holes designated for ceiling mount only. Drill
3/16" pilot holes and fasten bracket securely to a
structural support with the hardware provided.
Wall
Mounting Holes
Ceiling Mounting
The nail hole is for
positioning only.
You must use lag screws
to mount the header bracket.
The nail hole is for
_0_'@
You P°s2tti°7_lggn_Y;ew_
to mount the header bracket.
Holes
S _,
\j
_
:/_,
\J
\J
@))
Y
"/
Optional
Wall Mounting
Holes
_Header
Wall
_ Lag Screws
5/16"x9x1-5/8"
2x4
Structural
Support
Door
Spring
/
_-
/
I
Highest
Point of Travel
(of Garage Door)
-
Header
Wall
Garage
Door --
Vertical
Center
Line
Hardware Shown Actual Size
Lag Screw
5/16"-9 x 1-5/8"
14
Installation
Step 3
Attach the Rail to the Header
Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a protective
base.
If the door spring is in the way you'll need help. Have
someone hold the opener securely on a temporary
support to allow the rail to clear the spring.
Header Wall
• Position the rail bracket against the header bracket.
Bracket
• Align the bracket holes and join with a clevis pin as
shown.
Rail Bracket
• Insert a ring fastener to secure.
Ring Fastener
Header Bracket
Clevis Pin
5/16"x2-3/4 "
Rail
Bracket
Rail
Garage
Door
Foam Packaging
--
--
Opener Carton or
Temporary
Support
Hardware Shown Actual Size
°1
Clevis Pin
5/16" x 2-3/4"
O
Ring Fastener
15
The Safety Reversing Sensor
Information
you'll
need before
you begin
the installation
of the safety
reversing
sensor
The safety reversing sensor must be connected and
aligned correctly before the garage door opener will
move in the down direction. This is a required safety
device and cannot be disabled.
Installation
procedures
one-piece doors.
are the same Jbr sectional
Without a proper/y working safety reversing sensor,
persons(particu/ar/ychildren)cou/d be injuredor ki//ed
by a c/osing garage door. Read and follow all
instructions.
and
To protect small children, install the safety reversing
sensor so that the beamwill be no higher than 4"-6"
abovethegaragefloor.
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to the
receiving eye. The units can be installed on either side of
the garage door as long as the sun never shines directly
into the receiving eye lens.
Look at the label on the connector end of each case to
identify the sensors.
The brackets must be connected and fastened so that the
sending and receiving eyes face each other as shown.
Disconnect power to the garage door opener before
installingthe safetyreversingsensor.
The invisible light beam path must be unobstructed. No
part of the garage door (or door tracks, springs, hinges,
rollers or other hardware) can interrupt the beam while
the door is closing. If it does, use a piece of wood to build
out each sensor mounting location to the minimum depth
required for light beam clearance.
If an obstruction breaks the light beam while the garage
door is closing, the door will stop and reverse to full open
position and the opener lights will flash for 5 seconds.
The brackets must be securely fastened to a solid surface
such as the studs on either side of the door, or add a piece
of wood at each location if installing in masonry
construction.
//
Sensor
|
/
Beam
max.
I/4-6"
i_
Facing the door from inside the garage
16
above floor
Installation
Step 4
Install the Safety Reversing
Sensor
(Receiving
and Sending
Eyes)
Figure 1
Figures 1 and 2 show assembly of brackets and "C" wrap
based on the recommended installation of the sensors on
each side of the garage door as shown on page 16.
However, Figures 3 and 4 are variations which may fit
your installation requirements better. Make sure the
wraps and brackets are aligned so the sensors will face
each other across the garage door.
Mounting Bracket
With Square Holes
"C" Wrap
# 10-32x3/8"
Screws
#10 - 32
Lock Nuts
1. Fasten the "C" wraps to the mounting brackets having
square holes, using the hardware shown in Figure 3.
2. Connect each assembly to a slotted bracket, using the
hardware shown in Figure 2.
Note the alignment
sides of the door.
of the brackets
Figure 2
for left and right
1/4 x 1-1/2"
Lag Screws
3. Finger tighten the lock nuts.
Inside
_arage
Wall
4. Use bracket mounting holes as a template to locate and
drill (2) 3/16" diameter pilot holes on both sides of the
garage door, 4"-6" above the floor but not exceeding
6". (See warning on page 16.)
5. Attach bracket assemblies with 1/4"x1-1/2" lag screws
as shown in Figure 2.
1/4-20 x 1/2" Carriage Bolts
(with square shoulder)
,.., --
i
*"
6. Adjust right and left side bracket assemblies to the
same distance out from the mounting surface. Make
sure all door hardware obstructions are cleared.
Tighten the nuts securely.
_
Mounting
._.
.
J
Bracket
Slot
"C" Wrap
]
Mounting Bracket
with Square Holes
Lock Nuts
20
Figure 4
Figure 3
Alternate Wall Mount
Alternate
Inside
Garage
Wall T
InSide
Garage
Wall
Floor Mount
Sensor with wire
Indicator Light
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
/
Mounting Bracket
with Square Holes
Mounting Bracket
/ with Slot
"C" Wrap
Attach with
with wire
._ (oncrete anchors
not provided)
Indicator Light
Floor
J
Q
Hardware Shown Actual Size
©
#10 - 32 x 3/8"
Screw
#10 x 32
Lock Nut
1/4" - 20 x 1/2"
Lag Screw
Staples
17
Carriage Bolts
1/4" - 20
Lock Nut
Installation Step 4 (Continued)
Install
the Safety
Reversing
Sensor
7. Center each sensor unit in a "C"- wrap with lenses
pointing toward each other across the door (see
Figure 5).
"C" Wrap
Indicator
Light
8. Secure sensors with the hardware shown. Finger
tighten the wing nut on the receiving eve to allow for
final adjustment. Securely tighten the semting eye
wing nut.
Recommended
1/4-20 x 1-1/2"
Hex Bolt
Wire Routing
Figure 5
1. Using insulated staples, run the wires from both
sensors to the rail at the door header (see Figure 6).
Hardware Shown Actual Size
2. Cross and twist the two wires where they meet the rail
(see inset A). Run the wires inside the channels at the
top of the rail, along each side, to the power unit and
pull taut (see inset B). Do not use the lower (trolley)
channels.
1/4-20 x 1-1/2"
NOTE: If your access door is near the garage door,
you may choose to install the door control at this time
and run the door control wire along the rail with the
sensor wires. Use one rail channel for the door control
wire and the other channel for both sensor wires. If
you choose this option, follow instructions 1-3
on page 21 now.
A
--
3. Thread the wires through the tabs on top of the drive
shaft cover.
Sensor
Wire
4. With your screwdriver tip, tuck the wires snugly into
the rail channels. You will complete the wiring in
Installation Step 7.
Twist
Wires
Header
Wall --
Sensor
Wire
Header
Bracket
Rail
Channel
Figure 6
B
1. Run wires from sensors to end of rail
at the door header. Cross & twist here to
help contain wires in channels on tof
Bell Wire
2. Run wires along channels
to power unit and pull taut.
3. Thread wires through tabs
on top of Drive Shaft Cover.
4. With screwdriver
blade
tuck wires snugly into channels.
Foam
Packaging
Carton
Sensor
18
Invisible Light Beam
Protection Area
Sensor
Installation
Position
Step 5
the Opener
Follow instructions
as illustrated.
SECTIONAL
A 2x4 laid flat is convenient
to-rail distance.
• Raise
the opener
To prevent damage to steel, aluminum, fiberglass or
glass paneldoors, do not rest the opener on the door
withoutusinga 2x4.
which apply to your door type
for setting
Door or ONE-PIECE
an ideal
Door with Track
doorRail
2x4
onto a stepladder.
You will need help at this point
enough.
if the ladder
• Open the door all the way and place
the top section beneath the rail.
is not tall
a 2x4 laid flat on
Door
If the top panel hits the trolley when you raise the dooB
pull down on the trolley release arm to disconnect
the
inner and outer sections.
The trolley can remain
disconnected
until Step 13 is completed.
o
o
_L_--_
- --Trolley
Trolley
Release Arm
ONE-PIECE
Door without
Track
Header
Bracket
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of the
door.
Top of Opener
• Using a stepladder as a support, raise the opener to the
same distance as the door from the floor (it will be at a
slight angle as shown).
Foam
__
Packaging
Top of Door
• The top of the door should be level with the top of the
opener. Do not position the opener more than 3" above
this point.
19
Installation
Hang
Step 6
the Opener
The opener could fall and injure someone if it is not
properly secured. Fasten the opener securel y to
structuralsupportsof the garage.
Two representative
installations are shown. Yours may
be different. Hanging brackets should be angled, Figure
1, to provide rigid support. On finished ceilings, Figure 2,
attach a sturdy metal bracket to structural supports before
installing the opener. The bracket and f_stening hardware
are not supplied.
Supports
Figur
1. Measure the distance from each side of the opener to
the structural support.
2. Cut both pieces of the hanging bracket to required
lengths.
Lag Screws
5/16"xl -5/8"
Measure ",
Distance
3. Drill 3/16" pilot holes in the structural supports.
4. Attach one end of each bracket to a support with
5/16"xl-5/8" lag screws.
5/16"-18x7/8"
Hex Screws
5/16" Lock Washers
5/16"-18 Nuts
5. Fasten the opener to the hanging brackets with
5/16"- 18x7/8" screws, lock washers and nuts.
6. Check to make sure the rail is centered over the door
(or in line with the header bracket if the bracket is not
centered above the door).
Preferred Range of
Bracket Placement
7. Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
Figure 2
-- FINISHED CEILING --
Hardware Shown Actual Size
(Not
5/16"-9 x 1-5/8"
_ _ -
R,,,,,,,,,,D@
Hex Screw
5/16"- 18 x 7/8"
Nut 5/16" - 18
Supplied)...
Lockwasher
_
Hidden
Support
Lag Screws
5/16"xl
-5/8"
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
5/16"-18x7/8" Screw
5/16"
5/16"-18 Nut
5/16"
Preferred Range of
Bracket Placement
2O
Installation
Step 7
Install the Door Control
Connect all Wiring
and
Do not connectto live electricalwiring. Connect onlyto 24 Volt
low voltage wires. Connectionto live wires or higherv oltage
may causeseriousinjuryfrom shock,burnor electrocution.
Childrenoperatingor playing with a garage door opener can
injure themselvesor others. The garagedoor oou/d o/ose and
causeseriousinjury or death.
Install the door control(or any additionalpush buttons) outof
the reach of children and away from all moving parts of the
door and door hardware,but where the garage door is visible.
Do not allow children to operate the push b utton(s) or the
remotecontrol(s).
A movinggarage door couldinjuresomeone underit. Activate
the opener only when the door is properly adjusted,you can
seeit clearly,andthere are no obstructionsto doortravel.
Locate the door control within sight of the door at a
minimum height of 5 feet where small children cannot
reach, and away from all moving parts of the door and
door hardware.
The door control is typically attached directly to the wall.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in new
home construction), Console models" may be mounted to a
standard single gang boa"(Figure 2).
1. Strip 1/4" of insulation from one end of the bell wire
and connect it to the two screw terminals on the back of
the door control by color: white to 2 and white/red to 1.
Do NOT connect the power and operate the opener at
this time. See Step 9 on page 22.
2. Pry off cover along one side with a screwdriver blade
(see Figurel). Fasten with 6ABxl-1/4" self-tapping
screws (standard installation) or 6-32x1" machine
screws _re-wired installation) as follows:
STANDARD
CONTROL
CONSOLE
• Install bottom screw, allowing 1//8" to protrude above
wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
Top
Mounting
Hole
Terminal
Screws
Lighted
Push
Button
• Drill and install top screw with care to avoid cracking
plastic housing. Do not overtighten.
Bottom
Mounting
Hole
'BACK VIEW
• Insert top tabs and snap on cover.
3. (For standard installation only) Run the bell wire up the
wall and across the ceiling to the opener. Use insulated
staples to secure the wire in several places. Be careful
not to pierce the wire with a staple, creating a short. If
your access door is near the garage dooz you may run
this wire with the SaJoty Reversing Sensor wires along
the top of the rail. Seepage 18.
Figure 1
Figure 2
REMOVE & REPLACE
To Replace,
Inse rt
Top Tabs
•
COVER
PRE-WIRED
INSTALLATION
_-----.....,_o Remove,
_1_'_
Twist
_ _ ]]_ff[_'
I Here
//
4. Remove the Control Center door on the right panel of
the opener to access the terminal screws.
24 Volt
2-Conductor
Bell Wire
5. Thread all wires through the opening at the base of the
drive shaft cover (see Figure 3).
6. Insert the remaining wire through the hole in the power
unit and strip 1/4" of insulation from each set of wires.
Figure 3
WIRING TO
CONTROLCENTER
7. Connect the door control wire to the opener terminal
screws: white to 2 and white/red to 1. (See Figure 4.)
8. Separate the sensor white and white/black wires
sufficiently to connect to the opener terminal screws:
white to 2 and white/black to 3.
Insert wires
through
opening in
Drive Shaft Cover
9. Attach the User Safety Instruction label to the wall near
the door control, and the Maintenance Instruction label
in a prominent location on the inside of the garage door.
Page 32 explains how to operate the opener using the
door control.
Push wiring
through hole in chassis
(above Control Center)
and connect to opener
terminal screws
Hardware Shown Actual Size
Door Control
Control Console (std installation)
Control Console (pre-wired)
Sensor
Insulated
Staples
Dry Wall Anchors
21
Figure 4
OPENER TERMINAL SCREWS
(In Control Center)
Installation
Electrical
Step 8
Requirements
To preventelectrocutionor fire, installationand wiring
must be in compliancewith localelectricaland building
codes.
To reduce the risk of electric shock, your garage door
opener has a grounding type plug with a third grounding
pin. This plug will only fit into a grounding type outlet.
Do NOT usean extensioncord,2-wireadapter,or change
the plugin any way to makeit fit youroutlet.
If the plug doesn't fit into the outlet you have, contact a
qualified electrician to install the proper outlet.
To awdd installation th'fficulties,
do not run the opener until Step 9 below.
I
If permanent wiring is required by your local code,
refer to the following procedure:
To prevent electrocution, remove power from the
garagedoor opener and from the circuit you plan to
usefor the permanentconnection.
Permanent Wiring
Connection
To make a permanent connection through the 7/8" diam.
hole in the top of the opener (according to local code):
Ground Tab
Green
Ground Screw
• Remove the opener cover screws and set the cover aside.
• Remove the attached 3-prong cord.
Ground
• Connect the black (line) wire to the screw on the brass
terminal; the white (neutral) wire to the screw on the
silver terminal; and the ground wire to the green
ground screw. The opener must be grounded.
• Reinstall the cover.
Installation
White Wire
BlackWire
Step 9
Complete Safety Reversing
Installation
Sensor
Troubleshooting
1. If the semling eye indicator light does not glow
steadily after installation, check for:
• Plug in the opener. If your door control has a Lock
feature, be sure it is off. Green indicator lights in both
the sending and receiving eyes will glow swadily if
wiring connections and alignment are correct. If the
indicator light is offin the receiving eye (and the
invisible light beam path is not obstructed), alignment is
required.
• Electric power to the opener.
• A short in the white or white/black wires. These can
occur under staples or at screw terminal connections.
• Incorrect wiring between sensors and opener.
• An open wire (wire break).
• Loosen the receiving eye wing nut to allow slight
rotation of unit. Adjust sensor vertically and/or
horizontally until the green indicator light glows with a
steady light.
2. If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
• Check alignment.
• When indicator lights are glowing steadily in both units,
tighten the wing nut in the receiving eye unit.
• Check for an open wire to the receiving eye.
22
Installation
Install
Step 10
the Lights and Lens
• Install a 100 watt maximum light bulb in each socket.
The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is connected.
Then the lights will turn OFF.
• Insert bottom lens tabs into slots on chassis and tilt
towards chassis to engage top tabs, then drop down
gently into place. (See illustration.)
Top Lens Slot
Top Lens Tab
• To remove, lift lens up and gently tilt slightly outward
and down, then pull out to clear bulbs. Use care to
avoid snapping off bottom lens tabs.
Light Socket
Bottom Lens Slot
"..
Bottom Lens Tab
• If the bulbs burn out prematurely, replace with standard
neck Garage Door Opener bulbs. (Fluorescent bulbs are
not recommended because of possible interference with
receiver/transmitter signals.)
Lens
Insert Bottom Lens Tabs First
Installation
Step 11
Attach the Emergency
Rope and Handle
Release
Do not use the red handle to pull the door open or
closed. The rope knot could become untied and you
could fail. Use the emergencyreleaseonly to disengage
thetrolleyand, if possible,onlywhen thedoor is closed.
Garage doors are heavy. If the door is open when the
handleis pulled,the doorcould closeinadvertentlyif it is
not properly balanced. Serious injury may result to
personsunderthe door. Makesure the doorwayis clear
of personsand obstructionsbeforepullinghandlewhen
dooris open.
Trolley
I
Overhand
Knot
Trolley
--Rope
• Thread one end of the rope through the hole in the top
of the red handle so "NOTICE" reads right side up as
shown. Secure with an overhand knot.
Release Arm
_REem:rg
Hn2L ,e
Overhand
Knot _-_,
)
The knot should be at least 1" from the end of the
rope to prevent slipping.
• Thread the other end of the rope through the hole in the
release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet above the
floor. Secure with an overhand knot.
If it is necessary to cut the rope, heat seal the cut end
with a match or lighter to prevent unraveling.
23
Installation
Fasten
Step 12
Door Bracket
To prevent damage to steel, alumin urn, fiberglass or
glasspaneldoors,alwaysreinforcethe insideof thedoor
bothverticallyand horizontallywithan angleiron.
Follow instructions which apply to your door type
as illustrated below or on page 25.
A horizontal brace should be long enough to be secured to 2 vertical
height of the top panel.
supports.
A vertical brace should cover the
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron
are used to create a U-shaped support. The best solution is to check with your garage door manufacturer
for an
opener installation door reinforcement
kit.
SECTIONAL
Door Installation
Procedure
Header
Bracket
Horizontal
and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, aluminum, steel,
doors with glass panel, etc).
Figure 1
Vertical
Reinforcement
Vertical
Guideline
Door
Bracket
Location
i
i
i
,
Carriage Bolt
5/16"-18x2-1/2"
Door
Bracket
Lock
Washer
5/16"
UP
I
Nut
5/16"-18
Figure 2
Inside Edge
of Door or
einforcement
Board
uP
• Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation. Note the correct UP placement, as
stamped inside the bracket.
• Position the bracket on the face of the door within the
following limits:
"" "@G.
Door Bracket
Hardware Shown Actual Size
A) The top edge of the bracket 2-4" below the top edge
of the door.
B) The top edge of the bracket directly below any
structural support across the top of the door.
• Mark and drill 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.
Nut 5/16"-18
If your installation doesn't require vertical reinforcement
but does need top and bottom fastening holes for the door
bracket, fasten as shown in Figure 2.
Lockwasher
Carriage Bolt
5/16"-18 x 2-1/2"
24
5/16"
All ONE-PIECE
Please read and comply with the warnings
to one-piece doors also.
Door Installation
and reinforcement
Procedure
instructions
on page 24. They apply
Header Wall
2x4 Support
--Finished
Ceiling--
Horizontal and vertical
reinforcement is needed for
lightweight garage doors
(fiberglass, aluminum, steel,
door with glass panel, etc.).
Header
Bracket
Door
Bracket
Optional
Placement
of Door
Bracket
®
Vertical
Centerline of
Garage Door
Nut_
5/16"-18
_Lock
¢
,i
Door
Bracket
i
5/16"
Top of Door
t
i
(Inside Garage)
Top Edge
__
_j
Optional
of Door
Placement
i
For a door with no
_
the optional installation,
exposed
framing lag
or for
use
5/16"x1-1/2"
i
_
Carriage Bolt
g
5/16"-18x2-1/2"
screws (not supplied)
to fasten door
• Center the bracket on the top of the door, in line with
the header bracket as shown. Mark holes.
Hardware Shown Actual Size
• Drill 5/16" pilot holes and fasten the door bracket with
hardware supplied.
If the door has no exposed framing, drill 3/16" pilot holes
and fasten the bracket with 5/16"x1-1/2" lag screws (not
supplied) to the top of the door.
Nut
The door bracket may be installed on the top edge of
the door if required for your installation. (Refer to the
dotted line optional placement drawing.) Drill 3/16"
pilot holes and substitute 5/16"x1-1/2" lag screws (not
supplied) to fasten the bracket to the door.
5/16"-18
Lockwasher
Carriage Bolt
5/16"-18 x 2-1/2"
25
5/16"
Installation
Connect
Step 13
Door Arm to Trolley
Follow instructions which apply to your door type
as illustrated below and on page 27.
SECTIONAL
Doors Only
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the
inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in Figures 1, 2 and 3.
Figure 1:
Figure
• Fasten straight door arm section to outer trolley with a
clevis pin. Secure the connection with a ring fastener.
• Fasten curved section to the door bracket in the same
way as shown.
• Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far apart
as possible to increase door arm rigidity.
Inner
Trolley
2:
Outer
Trolley
Figure 2
Figure 1
Clevis
Pin
Emergency
Handle
Straight
Curved
Door Arm
Hole
Alignment
Screws
5/16"-18x7/8"
Door
Bracket
Alternative
Hardware Shown Actual Size
@ @ o
Figure 3:
• If holes in curved arm are above holes in straight arm,
disconnect straight arm. Cut about 6" from the solid
end. Reconnect to trolley with cut end down as shown.
Nut 5/16"-
• Bring arm sections together.
18
Lockwasher
5/16"
Ring Fastener
7!,,,,,,,,,,,D
{ oD
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
Hex Screw
5/16"- 18 x 7/8"
Proceed to Adjustment
Trolley will re-engage
opener is operated.
Figure 3
Screws
5/16"-18x7/8"
end
26
Clevis Pin
5/16" x 1"
Step 1, page
automatically
28.
when
the
All ONE-PIECE
Assemble
Doors
the Door Arm:
Door
Bracket
• Fasten the straight and curved door arm sections
together to the longest possible length (with a 2 or 3
hole overlap).
Ring
Fastener
1_
._.,.G:_'_\
'_-"'---._
Dk
\ _
Straight
Arm
_
Lock
Washers
5/16"
Nuts
5/16"-18
I
• With the door closed, connect the straight door arm
section to the door bracket with a clevis pin.
Screws
• Secure with a ring fastener.
--
5/1;c-r_s7/8"
Adjustment
Procedures
for One-Piece
_
_
__
_DCo;r
_""
Curved
Arm
Doors
On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted. Limit adjustment
screws are located on the right side panel as shown on page 28. Follow adjustment procedures below.
_
1
Closed
Door
Open Door
Door with
Backward Slant
Open Door Adjustment:
Decrease UP Travel Limit
• Turn the UP limit adjustment
5 1/2 turns.
Door Arm
Closed
Decrease
screw counter-clockwise
Door Adjustment:
DOWN Travel Limit
Turn the DOWN limit adjustment
5 complete turns.
screw clockwise
• Press the Door Control push button. The trolley will
travel to the fully open position.
Press the Door Control push button.
travel to the fully closed position.
• Manually raise the door to the open position (parallel
to the floor), and lift the door arm to the trolley. The
arm should touch the trolley just in back of the door
arm connector hole. Refer to the fully open
trolley/door arm positions in the illustration. If the arm
does not extend far enough, adjust the limit further.
One full turn equals 2" of trolley travel.
Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead of
the door arm connector hole. Refer to the fully closed
trolley/door
arm positions in the illustration.
If the arm
is behind the connector hole, adjust the limit further.
One full turn equals 2" of trolley travel.
Connect
the Door
Arm
The trolley
will
to the Trolley:
• Close the door and.join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be
necessary to lift the door slightly to make the connection.
• Secure with a ring fastener.
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown
in the illustration, decrease the UP limit until the door is parallel to the floor.
27
ADJUSTMENT
Adjustment
SECTION:
PAGES 28-
30
Step 1
Adjust the UP and DOWN Limits
Improperadjustment of the travel limitswill interferewith
the properoperation of the safety reverse system. The
door mightnot reverseproper/ywhenrequiredand cou/d
serious/yinjure or ki// someoneunderit. Test the safety
reversesystem monthly,and following all adjustmentsto
thetravel limits.See page30.
Do not make any limit adjustments until the safety
reversing sensors are completely installed.
Limit adjustment settings regulate the points at which the
door will stop when moving up or down.
The door will stop in the zip direction if anything
interferes with door travel. The door will reverse in the
down direction if anything interferes with the door travel
(including binding or unbalanced doors).
i i
0
0
0
0
I
0
0
0
0
00I
To operate the opener, press the Door Control push
button. Run the opener through a complete travel cycle.
• Does the door open and close completely'?
• Does the door stay closed and not reverse
unintentionally when fully closed'?
If your door passes both of these tests, no limit
adjustments are necessary unless the reversing test fails
(see page 30).
Right Side Panel
Adjustment procedures are outlined below. Run the
opener through a complete travel cycle after each
adjustment.
i_
i
Adjust UP Travel
LIMIT ADJUSTMENT
LABEL
Repeated operation of the opener during adjustment
procedures may cause the motor to overheat and shut
off. Simply wait 15 minutes and try again.
_@
Read the procedures carefully before proceeding to
Adjustment Step 2. Use a screwdriver to make limit
adjustments.
Adjust DOWN Travel
How and When to Adjust the Limits
If the door does not open completely but opens at least
five feet:
If the opener reverses in fully closed position:
Decrease down travel. Turn the DOWN limit adjustment
screw clockwise. One turn equals 2" of travel.
Increase up travel. Turn the UP limit adjustment screw
clockwise. One turn equals 2" of travel.
If door does not open at least 5 feet:
If the door reverses when closing and there is no
visible interference to travel cycle:
Adjust the UP (open) force as explained in Adjustment
Step 2.
If the opener lights are flashing, the Safety Reversing
Sensor is obstructed. Remove the obstruction.
Test the door for binding: Pull the emergency release
handle. Manually open and close the door. If the door is
binding, call for garage door service If the door is not
binding or unbalanced, adjust the DOWN (close) force.
See Adjustment Step 2.
If the door does not close completely:
Increase down travel. Turn the DOWN limit adjustment
screw counterclockwise. One turn equals 2" of travel.
If door still won't close completely, try lengthening the
door arm. (Page 26.)
If you have adjusted the door arm to the maximum length
and the door still will not close completely, lower the
header bracket. See Installation Step 1, pages 12 and 13.
28
Adjustment
Adjust
Step 2
the Force
Too muchforce on the doorwill interferewith the proper
operationof the safety reversesystem. The door might
not reverseproper/ywhen requiredand cou/d serious/y
injureor ki// someoneunderit. Do not increasethe force
beyondthe minimumamountrequiredto close the door.
Do not use the force adjustmentsto compensatefor a
bindingor stickinggaragedoor.Test the safetyreverse
system monthly,and following all adjustmentsto force
levels.See page30.
Force adjustment controls are located on the right panel
of the opener. Force adjustment settings regulate the
amount of power required to open and close the door.
The door will stop in the zip direction if anything
interferes with its travel. The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down direction
and stops in the zip direction. Weather conditions can
affect the door movement, so occasional adjustment may
be needed.
The maximum force adjustment range is about 3/4 of a
complete turn. Do not force controls beyond that point.
Turn force adjustment controls with a screwdriver.
I
©©©©
Force Adjustment
Label
Right Side
Panel
Force Adjustment
Controls
How and When to Adjust the Forces
Test the DOWN (close) force
If the door doesn't open at least 5 feet:
Grasp the door bottom when the door is about halfway
through DOWN (close) travel. The door should reverse.
Reversal halfway through down travel does not
guarantee reversal on a one-inch obstruction. See
page 30. If the door is hard to hold or doesn't reverse,
decrease the DOWN (close) force by turning the control
counterclockwise.
Increase UP (Open) force by turning the control
clockwise. Make small adjustments until door opens
completely. Readjust the UP limit if necessary. After each
adjustment, run the opener through a complete travel
cycle.
If the door reverses during the down (close) cycle and
the opener lights aren't flashing:
Make small adjustments until the door reverses normally.
After each adjustment, run the opener through a complete
cycle.
Increase DOWN (close) force by turning the control
clockwise. Make small adjustments until the door
completes a close cycle. After each adjustment, run the
opener through a complete travel cycle. Do not increase
the force beyond the minimum amount required to
close the door.
Test the UP (open) force
Grasp the door bottom when the door is about halfway
through UP (open) travel. The door should stop. If the
door is hard to hold or doesn't stop, decrease UP (open)
force by turning the control counterclockwise.
Make small adjustments until the door stops easily. After
each adjustment, run the opener through a complete travel
cycle.
29
Adjustment
Step 3
Test the Safety Reversing
Sensor
Without a properly working safety reversing sensor,
persons(particularly children)could be seriously injured
or killed if trappedby a c/osinggaragedoor. Repeatthis
test oncea month.
• Press the remote control push button to open the door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the door.
The door will not move more than an inch, and the
opener light will flash Jbr 5 seconds
Professional service is required if the opener closes the
door when the safety reversing sensor is obstructed.
The garage door opener will not close from a remote if
the indicator light in either sensor is off(alerting you
to the fact that the sensor is misaligned or obstructed).
{
.£
The garage door can be closed by pressing and holding the
Door Control push button until down travel is completed.
i
i
Safety Reversing Sensor
Adjustment
Safety Reversing Sensor
Step 4
Test the Safety Reverse
System
Failureto test and adjust the safety reversesystem may
resultin serious injuryor death to persons trappedby a
closinggarage door. Repeatthis test once a monthand
adjustas needed.
Test
• Place a one-inch board (or a 2x4 laid flat) on the floor,
centered under the garage door.
• Operate the door in the down direction. The door must
reverse on striking the obstruction.
L_
Adjustment
If the door stops on the obstruction,
enough in the down direction.
it is not traveling far
• Increase the DOWN limit by turning the DOWN limit
adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
On a sectional door, make sure limit adjustments do
not force the door arm beyond a straight up and down
position. See the illustration on page 26.
• When the door reverses on the one-inch board, remove
the obstruction and run the opener through 3 or 4
complete travel cycles to test adjustment.
If the door will not reverse after repeated adjustment
attempts, call for professional garage door service.
_laid
Important Safety Check
Repeat Adjustment
Steps 1 - 4 after:
• Each adjustment of door arm length, force controls
limit controls.
or
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
3O
flat)
IMPORTANT SAFETY INSTRUCTIONS
To reduce
the risk of severe injury
or death
to persons:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Do not permit children either to operate or to play with the opener. Keep remote control in a location
inaccessible to children.
3. Operate opener only when the door is in full view and free from any obstruction. Keep the door in sight until
it is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4. Check safety reversal system monthly. See page 30. The garage door MUST reverse on contact with a one
inch object (or a 2x4 board laid flat) placed on the floor. If an adjustment is made to one of the controls
(either force or limits of travel), the other control may need to be adjusted also, and the safety reversal system
must be checked. Failure to properly adjust the opener may result in severe injuly or death.
5. If possible, use the emergency release only when the door is in a closed position. Caution should be taken
whenever the disconnect cord is actuated with the door open. Weak or broken springs may cause the door to
fall rapidly, causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY BALANCED. See page 3. An improperly balanced door may not
reverse when required, and couhl result in severe injuly or death. Repairs to cables, spring assemblies and
other hardware must be made by a professional garage door person.
7. Disconnect the electric power to the garage door opener before making any repairs
or removing
the covers.
SAVE THESE INSTRUCTIONS
Care of Your Opener
The remote control
Force and Limit Adjustment
The lithium batteries should
produce power for up to 5 years.
To replace batteries, use the visor
clip or screwdriver blade to pry
open the case, as shown. ("Open"
location is stamped on back of
transmitter case.) Insert batteries
positive side down.
Controls
FORCECONTROLS
LIMIT CONTROLS
3-FUNCTION
Open this end
first to avoid
cracking
housing
Replace cover as follows. 3-Fzmcaon remote." Insert the 3
tabs at the opposite end and snap shut. Compact
3-Fzmction remote." Snap shut along both sides.
Weather conditions may cause some minor changes in
door operation requiring some re-adjustments,
particularly
during the first year of operation.
Dispose of old batteries properly.
Pages 28 and 29 refer to the limit and force adjustments.
Only a screwdriver is required. Follow the instructions
carefully.
Keep batteries
away from small
swallowed, promptly notify doctor.
Repeat the safety reverse test (page 30) after any
adjustment of limits or force.
Maintenance
Once a Month
children.
If
Schedule
Repeat the safety reverse test. Make any necessary
adjustments (See page 30).
Manually operate door. If it is unbalanced or binding,
call for professional garage door service.
Once a Year
Check to be sure door opens & closes fully. Adjust
limits and/or force if necessary. (See pages 28 & 29.)
Oil door rollers, bearings and hinges. The opener does
not require additional lubrication. Do not grease the door
tracks.
31
Operation of Your Opener
Activate the opener with any of the following:
• The Remote Control: Hold push button down until
the door starts to move.
• The Door Control: Hold push bar or button down
until the door starts to move.
• The Outdoor
Accessories)
Key Switch or Keyless Entry:
Weakor brokenspringscould allow an open door to fall
(either rapidly or unexpectedly), resulting in serious
injury, death or property damage. If possible, use the
manualrelease rope and handle only when the door is
fully closed.
(See
When the opener is activated with the safety reversing
sensor installed and correctly aligned:
1. If open, the door will close. If closed, the door will
open.
To open the door
manually:
(_
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for entry
and exit of pets and for fresh air).
Trolley
4. If the door has been stopped in a partially open
position, it will close.
Position)
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
Lockout position
(Manual disconnect)
7. The garage door will reverse in the closing cycle when
the invisible beam is broken. If fully open, the door
will not close when the beam is broken. The sensor
has no effect in the opening cycle.
If the sensor is not installed, or is not aligned correctly,
the door won't close from any remote control. You can
close the door with the Door Control, the Outdoor Key
Switch, or Keyless Entry, however, if you activate them
until down travel is complete. If you release them too
soon, the door will reverse.
To reengage the trolley:
Pull the emergency release
handle toward the opener at
a 45 ° degree angle so that
the trolley release arm is
horizontal. The trolley will
reconnect on the next UP or
DOWN operation, either
manually or by pressing the
Door Control push button.
The opener lights will blinkJor 5 seconds" when the safety
reversing sensor causes the door to reverse.
Opener Lights will turn on under the following
conditions: When the opener is initially plugged in; when
the power is interrupted; when the opener is activated.
They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature is activated.
Bulb size is 100 watts maximum.
Operation
The door should be fully
closed if possible. Pull down
on the emergency release
handle (so that the trolley
release arm snaps into a
vertical position) and lift the
door manually. The lockout
feature prevents the trolley
from reconnecting automatically, and the door can
be raised and lowered
manually as often as
necessary.
o
©
- --Trolley
Trolley
_, _Release
Emergency
Release _
Arm
Handle _
(Pull at 45 ° angle)
To reconnect
of the Door Controls
(all may not be included
Press the lighted push button to open or close the door.
(see page 21)
with your model)
Premium Console (cont.):
LockJeamre." The Lock feature is designed to prevent
operation of the door from remote controls. However,
the door will open and close from the Door Control, the
Outdoor Key Switch and the Keyless Entry Accessories.
To activate." Press and hold the small round Lock
button for 2 seconds. The push button light will flash
as long as the Lock feature is on.
Press again to reverse the door during the closing cycle
or to stop the door while it's opening.
Premium Console:
LightJeamre." Press the large round Light button. If the
opener light is of/, it will turn on. If the opener light is
on, (even in the 4-1/2 minute automatic cycle) it will
turn off.
To turn oJf" Press and hold
2 seconds.The push button
Lock feature will also turn
button on the opener panel
But if you use the Light button to turn the lights on and
then activate the opener, the lights will turn offafter 41/2 minutes.
The Light button will not control the opener lights when
the door is in motion.
32
the Lock button again for
light will stop flashing. The
off whenever the SRT
is activated.
Receiver & Remote Control Programming
NOTICE: To comply with FCC rules, adjustment or modification of this
receiver and/or transmitter are prohibited, except for changing the code
setting or replacing the transmitter battery. THERE ARE NO OTHER
USER SERVICEABLE PARTS.
Childrenoperatingor playingwith a garagedoor opener
can injurethemselvesor others. The garagedoor could
c/ose and cause serious injury or death. Do not allow
childrento operatethe door control(s)or remotecontrol
transmitter(s).
Your garage door opener has been factory set to operate
with the large push button on the remote control.
However, you can use either of the two small buttons, if
you prefer. And, the 3-function remote can also activate
additional garage door openers and/or light acontrols.
A movinggaragedoor cou/dinjureor ki//someone under
it. Activate the opener onlywhen you can see the door
clearly, it is free of obstructions, and is properly
adjusted.
Your "SRT" garage door opener will operate with:
• up to four "SRT" remote control transmitters (with
green indicator lights),
• a Keyless Entry System, and
• code switch remote controls with red indicator lights.
Below are instructions for programming your opener to
match the other buttons on your remote control and any
additional remotes you may purchase. See available
accessories on page 38.
Figure 1
Select a remote control push
button to operate opener
To add a remote control:
1. Press and hold the selected remote push button, see
Figure 1.
2. Then press and release the "SRT" button on the right
side panel of the opener, Figure 2. The opener lights
will flash once.
3-Function
Remote Control
3. Release the remote push button.
Now the opener will operate when the remote control
push button is pressed.
If yon release the remote control push button before
the opener lights flash, the opener will not accept the
code.
Figure 2
Garage Door Opener
(With "SRT" Button)
To change the selected push button on the same
remote:
If you decide to use a different remote control button than
originally programmed into the opener, you need to erase
all the learned codes and reprogram each remote used to
operate the garage door opener.
To erase all remote control codes:
• Press and hold the "SRT" button on the opener panel
until the indicator light turns off (about 6 seconds).
All the codes the opener has learned will be erased.
• To reprogram, repeat Steps 1 - 3 for each remote
control in use.
Code programming
the opener panel.
instructions
"SRT"
Button
are also located on
33
Indicator
Light
Troubleshooting
Situation
Probable
Cause & Solution
The opener doesn't
operate from either
the door control or
the remote control:
1. Does the opener have electric power'? Plug a lamp into the outlet. If it doesn't light, check the
fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.)
2. Have you disabled all door locks'? Review installation instruction warnings on Page 11.
3. Is there a build-up of ice or snow under the door'? The door may be frozen to the ground.
Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
Opener operates from
the remote control, but
not from the door
control:
1. Is the door control push bar lit'? If not, Remove the bell wire from the opener terminal
screws. Short the red and white terminals by touching both terminals at the same time with
a piece of wire. If the opener runs, check for a faulty wire connection at the door control, a
short under the staples, or a broken wire.
2. Are the wiring connections
The door operates from
the door control, but not
from the remote
control:
correct'? Review Installation
Step 7, page 21.
1. If your model has the Lock feature, turn it off.
2. Is the door push button flashing'? Your opener needs to re-learn a remote control code.
Refer to instructions on the opener panel.
3. Does the battery test light glow when the remote control push button is pressed'? If not,
replace the battery.
4. Program the receiver to match the remote control code.
5. Repeat the receiver programming
The remote control has
short range:
procedure with all remote controls.
1. Check the battery test light. If the light is dim, replace the battery.
2. Change the location of the remote control in your car.
3. Check to be sure the antenna on the right side panel of opener extends fully.
4. Some installations may have shorter range due to a metal door, foil backed insulation, or
metal garage siding.
Opener noise is
disturbing in living
quarters of home:
If operational noise is a problem because of proximity of the opener to the living quarters, the
Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration
to the house and is easy to install.
The garage door
opens and closes by
itself."
Be sure that all remote control push buttons and battery indicator lights are off.
2. Remove the bell wire from the door control terminals and operate from the remote control
only. If this solves the problem, the door control is faulty (replace), or there is an
intermittent short on the wire between the door control and the opener.
The door doesn't open
completely:
1. If the door has been working properly but now doesn't open all the way, increase the zip
Jorce. See page 29.
.
2. Is something obstructing the door'? Remove the obstruction or repair the door.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn equals
2 inches of travel. See page 28.
Repeat the safety reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review
the travel limits adjustment
Repeat
limit.
the safety
reverse
procedures
on page 28.
test after any adjustment
34
of door arm length,
close fi_rce or down
Troubleshooting
(continued)
Situation
Probable
Cause & Solution
The door opens but
won't close:
1. If the opener lights blink, check the safety reversing sensor. See page 22.
2. If the opener lights do not blink and it is a new installation, check the down force. See
Adjustment Step 2, page 29. For an existing installation, see below.
Repeat the safety reverse test after the adjustment is complete.
The door reverses fi_r no
apparent reason and
opener lights don't
blink:
1. Is something obstructing the door'? Pull the emergency release handle. Operate the door
manually. If it is unbalanced or binding, call for professional garage door service.
2. Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 29.
4. If door reverses in theJidly closed position, decrease the travel limits (page 28).
Repeat the safety reverse test after adjustments to fi_rce or travel limits. The need fi_r
occasional adjustment of the fi_rce and lim# settings is normal. Weather comh'tions in
particular can affect door travel.
The door reverses fi_r no
apparent reason and
opener lights blink fi_r
5 secomls after
reversing:
Check the safety reversing sensor. Remove any obstruction or align the receiving eye. See
pages 12 and 22.
The opener lights...
don't turn on:
Replace the light bulb(s) (100 watts maximum). Use a stamlard neck garage door opener bulb
if regular bulb burns out.
don't turn off"
Is the Light feature on ').Turn it q[[.
The opener strains or
maximum force is
needed to operate door:
The door may be out of balance or the springs are broken. Close the door and use the
emergency release handle to disconnect the trolley. Open and close the door manually. A
properly balanced door will stay in any point of travel while being supported entirely by its
springs. If it does not, disconnect the opener and call for professional garage door service.
Do not increase the fi_rce to operate the opene_
The opener motor
hums briefly, then
won't work:
1. The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable the
door lock.
Repeat the safety reverse test after the adjustment
The opener won't
operate due to power
failure:
is complete.
1. Use the emergency release handle to disconnect the trolley. The door can be opened and
closed manually. When power is restored, press the Door Control push button and trolley
will automatically reconnect (unless trolley is in lockout position.) See page 32.
2. The Emergency Key Release accessory (for use on garages with no service door)
disconnects the trolley from outside the garage in case of power failure.
35
Repair Parts
Rail Assembly
Parts
10
2
8
7
3
6
Installation
KEY PART
NO. NO.
DESCRIPTION
1
41A4796
Hardware bag
2
41A4795
3
12B569-1
Hardware bag (includes
sprocket coupling)
Left rail bracket
4
12B569-2
Right rail bracket
5
1C4827-2
Screw drive rail assembly
6
12B560
7
81C168
Rail support brace
Rack
8
41C4677
Complete trolley assembly
9
25A18
Sprocket coupling
10
41A4836
Drive sprocket kit
Parts
6
4
2
8
KEY
PART
NO.
NO.
DESCRIPTION
1
41A4899
Standard control console
2
29B134
3
41A4873
Visor clip
3-function remote control case
(no circuit board)
4
10A19
3V 2016 Lithium battery (2 required)
5
41A2828
6
217A238
Emergency release rope & handle assy.
2-Conductor bell wire: white & white/red
7
41A5047
Door bracket w/clevis pin & fastener
8
41A4353
Header bracket w/clevis pin & fastener
9
41A4373A
10
10
178B35
Safety sensor kit: receiving and sending
eyes with 3' 2-conductor bell wire attached
Curved door arm section
11
178B34
Straight door arm section
12
12B483
C-wrap bracket
13
12B484
14
12B485
Square hole bracket
Slotted bracket
15
12B350
_1
ol
11 1
12
- I
15
13
ol
ol
QI
14
Hanging brackets
NOT SHOWN:
ol
ol
QI
41A4116
Safety sensor hardware (see page 5)
ol
41A4675-3
Installation hardware bag (see page 5)
Owner's manual
,j
114A2043
36
Repair Parts
Opener Assembly
Parts
Brown
Wire
Drive_
(Down)
Contact
_ Pr_
=
/
I
Center Limit
Contact
8¢
LIMIT SWITCH ASSY,
d,
(Up)
Contact
_
Yellow
Wire
8a
9
_Ui
_10
8b
8
13
14
17
15
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
1
31 D426
2
41 B4245
Drive shaft cover
9
41A4843
Interrupter cup
Line cord
10
41A4837
Worm gear and retainer
DESCRIPTION
3
30B363
Capacitor-
11
41C4669
Wire harness assembly
4
5
12A373
41A3150
Capacitor bracket
Terminal block w/screws
12
41C4672
RPM sensor assembly
13
41 D4674-9C
Receiver logic board assembly
6
41 D4671
Limit switch assembly
14
41 D4839-5
Cover
1/2 HP
7
12D554
Limit switch bracket
15
lC4840-6
Control Center access door
8
8a
8b
8c
8d
41 D4759
144B41
144B42
20C14
158A69
Complete Motor Drive Assy., with
22T Pulley
28T Pulley
Drive Belt
Retainer Ring
16
175C123
Light socket
17
108D47
Light lens
37
Accessories
139.53702
Available For Your Opener
139.53879
Emergency Key Release:
Required for a garage with NO access
door. Enables homeowner to open
garage door manually from outside by
disengaging trolley.
139.53703
Outdoor
139.53859
Key Switch:
139.53876
8 Foot Rail Extension
139.53774
Support Brackets:
Door Clearance
(For Sectional
3-Function
Remote
Multi-Function
Keyless Entry:
Enables homeowner to operate garage
door opener from outside by entering
a 4 digit code on specially designed
keypad.
For finished ceilings or where
additional support is required, based
on garage construction.
Includes brackets and fastening
hardware.
139.53709
Compact
Control:
With loop for attaching key ring.
To allow an 8 foot door to open fully.
53885
Remote Control:
Includes visor clip.
Operates the garage door
automatically from outside when
remote control is not handy.
139.53404
3-Function
Plug-In Light Control:
Enables homeowner to turn on a lamp,
television or other appliance from car,
bedside, or anywhere in the home
with a remote.
139.53773
Brackets:
Doors" Only)
Wire-In
Light Control:
Wires into light switch box to enable
homeowner to control outside or
inside lights with remote. (Can also be
operated manually.)
Replaces top brackets and rollers on
door to reduce height of door travel.
For use when installing opener in
garage with low headroom clearance.
38
Index
Access
Door/Emergency
Electrical
Key Release
Safety Warnings
Accessory
...............................................................................................
6, 7, 35, 36
......................................................................................................................................
Garage Door
Testing for balance, binding and sticking .................................................................................................................
Determining high point of travel:
Sectional door ..................................................................................................................................................................
One-piece door ................................................................................................................................................................
Disabling existing locks .................................................................................................................................................
Force controls
Adjustment procedures ....................................................................................................................................................
Problems that might require force adjustments .........................................................................................................
Safety warnings .........................................................................................................................................................
Door hardware ..............................................................................................................................................
3, 11,
Maintenance ...........................................................................................................................................................
Reinforcement requirements ....................................................................................................................................
Removing of all ropes ....................................................................................................................................................
Possible door damage ...............................................................................................................................................
Travel limits
Adjustment procedures ..............................................................................................................................................
Problems that might require limit adjustments .........................................................................................................
Safety warnings .........................................................................................................................................................
2, 22, 31
3, 28, 31
12
13
3, 11
29
34, 35
29, 31
12, 31, 32
11, 28-31
4, 24, 25
3, 11
3, 19, 24
27, 28
34, 35
28, 31
Emergency Release Rope & Handle
Lockout feature .................................................................................................................................................................
32
Manual disconnect .......................................................................................................................................................
32, 35
Safety warnings ...............................................................................................................................................
11, 23, 31, 32
Opener Terminals
Door control connections ..................................................................................................................................................
Safety reversing sensor connections ............................................................................................................................
21
21, 22
Receiver & Remote Controls
Programming the receiver .................................................................................................................................................
Erasing all codes ................................................................................................................................................................
Safety warning ...................................................................................................................................................................
Problems with remote control transmitter operation .........................................................................................................
Safety
Reversing
Sensor
........................................................................................................................................
33
33
33
34
16-18,
30
Safety Reverse Test Procedure ..........................................................................................................................................
30
Testing required ...............................................................................................................................................
11, 30, 34, 35
Safety reverse system problems
Securing header bracket to wall ......................................................................................................................................
12
Adjusting travel limits .....................................................................................................................................................
28
Applying excessive force on the door .............................................................................................................................
29
Buckling or uneven floor ...............................................................................................................................................
4, 5
Safety
Warnings
......................................................................
2, 3, 11, 12, 16, 19, 20, 21, 22, 23, 24, 28, 29, 30, 31, 32, 33
Troubleshooting
............................................................................................................................................................
34, 35
User Instruction
Label for Garage Wall ....................................................................................................................
11, 21
Vibration
Noise (isolator
kit) .............................................................................................................................................
39
34
SEARS
I:RRFTSMRN,
OWNER'S
MANUAL
GARAGE DOOR OPENER
For the repair or replacement parts you need
Call 7 am - 7 pm, 7 days a week
1-800-366-PART
Model No.
139.53491SRT
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day, 7 days a week
1-800-4-R
E PAl R
(1-800-473-7247)
The model number
label is located on the
For the location of a
Sears Repair Service Center in your area
Call 24 hours a day, 7 days a week
1-800-488-1
back of your opener.
222
A
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am - 5 pm, Monday-Saturday
When requesting
service or ordering
parts, always provide
the following
information:
1-800-827-6655
SEARS
;/:_r/;l,_:;jr/[_]._
America's
• Product Type
• Model Number
• Part Number
Repair Specialists
SEARS WARRANTY
FULL 90-DAY WARRANTY
ON GARAGE DOOR OPENER
For 90 days from the date of purchase, Sears will repair any defect in material or
workmanship at no charge.
LIMITED WARRANTY
• Part Description
From the 91 st day until one year from the date of purchase, Sears will furnish
replacement parts for any defective parts, free of charge. You pay for labor.
LIMITED WARRANTY ON 1/2 HP MOTORS FOR CRAFTSMAN OPENERS
After 1 year and through 5 years, Sears will furnish replacement
defective parts in motor, free of charge. You pay for labor.
LIMITATION ON LIABILITY
Sears will not be liable for loss or damage to property
consequential
loss or expense from property damage
from the use of this product.
parts for any
or any incidental or
due directly or indirectly
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty does not cover repairs necessary because of operator abuse or
negligence, including failure to install, adjust and operate the opener according to
instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST
SEARS STORE OR SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
SEARS ROEBUCK
AND COMPANY,
Dept. 817WA,
Hoffman
Estates,
IL 60179
[]
114A2043
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
@1996, All Rights Reserved
Printed in Mexico