Electrolux EFC 9670-6670 User manual

User manual
Manual de instrucciones
Manual de instruções
EFC 9670-6670
EFC 9671-6671
EFC 9673
electrolux safety warnings
Welcome to the world of Electr
olux
Electrolux
Thank you for choosing a first class
product from Electrolux, which
hopefully will provide you with lots of
pleasure in the future. The Electrolux
ambition is to offer a wide variety of
quality products that make your life
more comfortable. You find some
examples on the cover in this manual.
Please take a few minutes to study this
manual so that you can take advantage
of the benefits of your new machine.
We promise that it will provide a
superior User Experience delivering
Ease-of-Mind.
Good luck!
3
GB
4
electr
olux contents
electrolux
Contents
GB
Safety warnings ................................ 5
Description of the Appliance ............. 7
Control Panel .................................... 8
Maintenance and Care ................... 14
Special accessories ........................ 19
Something Not Working .................. 19
Installation ...................................... 20
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips.
Environmental information.
electrolux safety warnings
5
GB
Safety warnings
For the user
• The cooker hood is designed to
extract unpleasant odours from the
kitchen, it will not extract steam.
• Always cover lighted elements, to
prevent excess heat from damaging
the appliance. In the case of oil, gas
and coal fired cookers it is essential
to avoid open flames.
• Also, when frying, keep the deep
frying pan on the cooker top/cooker
under careful control.
• The hot oil in the frying pan might
ignite due to overheating.
• The risk of self-ignition increases
when the oil being used is dirty.
• It is extremely important to note that
overheating can cause a fire.
• Never carry out any flambé cooking
under the hood.
om the
• Always disconnect the unit fr
from
power supply befor
e carrying out
before
any work on the hood, including
replacing the light bulb (take the
cartridge fuse out of the fuse holder
or switch off the automatic circuit
breaker).
• It is very important to clean the hood
and rreplace
eplace the filter at the
recommended intervals. Failur
e to
Failure
do so could cause gr
ease deposits
grease
to build up, rresulting
esulting in a fir
e hazar
d.
fire
hazard.
• The appliance is not intended for use
by young children or infirm persons
without supervision.
• Older children must be supervised if
using the appliance.
• Young children should be supervised
to ensure that they do not play with
the appliance.
• WARNING - Ensure that the
appliance is switched off before
replacing the lamp to avoid the
possibility of electric shock.
This appliance is marked according to
the European directive 2002/96/EC on
Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product.
The symbol
on the product, or on
the documents accompanying the
product, indicates that this appliance
may not be treated as household
waste. Instead it should be taken to the
appropriate collection point for the
recycling of electrical and electronic
equipment.
Disposal must be carried out in
accordance with local environmental
regulations for waste disposal.
For more detailed information about
treatment, recovery and recycling of
this product, please contact your local
council, your household waste disposal
service or the shop where you
purchased the product.
6
GB
electr
olux safety warnings
electrolux
For the installer
• When used as an extractor unit, the
hood must be fitted with a hose
having preferably the same diameter
as the outlet hole.
Attention: The hose is not supplied
and must be purchased separately.
• When installing the hood, make sur
e
sure
you observe the following minimum
distance fr
om the top edge of the
from
cooking hob/ring surfaces:
electric cookers
500 mm
gas cookers
650 mm
If the instructions for installation for
the gas hob specify a greater
distance, this must be adhered to.
• The national Standard on fuelburning systems specifies a maximum depression of 0.04 mbar in
such rooms.
• The air outlet must not be connected
to chimney flues or combustion gas
ducts. The air outlet must under no
circumstances be connected to
ventilation ducts for rooms in which
fuel-burning appliances are installed.
• The air outlet installation must comply
with the regulations laid down by the
relevant local authorities.
• When the unit is used in extraction
mode, a sufficiently large ventilation
hole must be provided, with
dimensions that are approximately
the same as the outlet hole.
• National and regional building
regulations impose a number of
restrictions on using hoods and fuelburning appliances connected to a
chimney, such as coal or oil roomheaters and gas fires, in the same
room.
• Hoods can only be used safely with
appliances connected to a chimney if
the room and/or flat (air/environment
combination) is ventilated from
outside using a suitable ventilation
hole approximately 500-600 cm2
large to avoid the possibility of a
depression being created during
operation of the hood.
• If you have any doubts, contact the
relevant controlling authority or
building inspector’s office.
• Since the rule for rooms with fuel
burning appliances is “outlet hole of
the same size as the ventilation hole”,
a hole of 500-600 cm2, which is to
say a larger hole, could reduce the
performance of the extractor hood.
• If the hood is used in its recirculation
mode, it will operate simply and safely
in the above conditions without the
need for any of the aforementioned
measures.
• When the hood is used in its
extraction mode, the following rules
must be followed to obtain optimal
operation:
- short and straight outlet hose
- keep bends in outlet hose to a
minimum
- never install the hoses with an
acute angle, they must always
follow a gentle curve.
- keep the hose as large as possible
(preferably the same diameter as
the outlet hole).
- the length should be no more than:
3 metres with one 90° bend
2 metres with two 90° bends
Bends of more than 90° will reduce
the efficiency of the hood and
reduce the airflow.
• Failure to observe these basic
instructions will drastically reduce the
performance and increase the noise
levels of the extractor hood.
electrolux description of the appliance
Description of the Appliance
7
Coupling ring
GB
• The cooker hood is designed to
extract unpleasant odours fr
om the
from
kitchen, it will not extract steam.
• The hood is supplied as an extractor
unit and can also be used with a
recirculation mode by fitting a
charcoal filter.
Extraction mode
• In this mode fumes are extracted to
the outside via a hose connected to
the coupling ring
ring.
• In order to obtain the best performance the hose should have a diameter
equal to the outlet hole.
Recir
culation mode
Recirculation
coal
• The air is filtered through a char
charcoal
filter and returned to the kitchen.
• You will need an original charcoal filter
for the recirculation mode. (See
Special Accessories).
8
electr
olux control panel
electrolux
Control Panel
GB
• Best results are obtained by using a
low speed for normal conditions and
a high speed when odours are more
concentrated.
Turn the hood on a few minutes
before you start cooking.
The hood should be left on after
cooking for about 15 minutes or until
all the odours have disappeared.
Y EFC 9671-6671-9673
• ONL
ONLY
models: The hood can also be
commanded from the control panel
or the remote control. (the remote
control is a special accessory and is
ordered separately).
ect ventilation: If the cooker
• Corr
Correct
hood is to work correctly there must
be an under pressure in the kitchen.
It is important to keep the kitchen
windows closed and have a window
in an adjacent room open.
• The control switches are located on
the hood’s front panel
electrolux control panel
9
Model EFC 9670-6670
GB
Light switch
(ON/OFF)
Push-button 1
(ON/OFF)
ON/OFF motor
speed key
• Light switch (ON/OFF): this switch is
used to turn the light fitted in the
hood on and off.
• ON/OFF motor speed key: serves to
enable and disenable the speed
selection keys.
• Push-button 1 (ON/OFF): used to set
the fan to speed 1.
• Push-button 2 (ON/OFF): used to set
the fan to speed 2.
• Push-button 3 (ON/OFF): used to set
the fan to speed 3.
Push-button 3
(ON/OFF)
Push-button 2
(ON/OFF)
10
electr
olux control panel
electrolux
Modell EFC 9671-6671
GB
6
1
1.
2.
3.
4.
5.
6.
2
3
4
5
Lights key ON/OFF
Motor stand-by/OFF key:
Stand-by (dot in the lit display): all the commands are enabled for functioning,
press the key for more than 1 second to set the hood on OFF.
OFF (display off): and the commands with the exception of the ON/OFF lights
key are disenabled. Press the key for more than 1 second to set the hood in
Stand-by.
Selection and aspiration speed (power) and timer key: press to select the
1-2-3-1aspiration speed (power) or set the hood in stand-by in the sequence:1-2-3-12-.....
T imer (ON/OFF): once the speed (power) has been selected, pressing
successively for 2 seconds activates (ON – flashing dot on the display) or
deactivates (OFF) the timer function. This allows the aspiration speed (power)
selected for a predetermined time to function:
Aspiration Speed (power) 1: 20 minutes
Aspiration Speed (power) 2: 15 minutes
Aspiration Speed (power) 3: 10 minutes
After which the hood goes into stand-by.
Intensive aspiration (power) key (timed) ON (flashing dot on the display)/OFF:
/OFF:
press to select the intensive aspiration speed (power). It will function for 5
minutes after which the hood goes into stand-by
stand-by.
Pressing before the five minutes have passed, the hood returns to the
previously set speed.
Filters saturation rreset
eset key: see the relative text on the following pages.
Display
Should the hood or the controls fail to operate: disconnect the power supply for at
least 5 seconds. After reconnecting the power supply wait 15 seconds and then
check that the cooker hood is now operating
correctly.
electrolux control panel
Gr
ease and char
coal filter
Grease
charcoal
maintenance indicator
This hood is fitted with a device that
indicates when it is necessary to clean
the grease filter or the charcoal filter (if
the hood is used in the recirculation
version with a charcoal filter).
On delivery, the hood is not supplied
with a charcoal filter, so the saturation
indicator will be disabled.
If the hood is to be used with a
charcoal filter, the saturation
indicator light must be enabled as
follows:
OFF
Set in "OFF
OFF" the hood.
Press buttons 4 and 5 simultaneously
and hold them for 3 seconds. At first
only the grease filter LED F will light up,
but when the charcoal filter LED C
lights up the saturation indicator will be
enabled.
To disable it: Press buttons 4 and 5
again simultaneously and hold
them for 3 seconds, until the charcoal
filter LED goes out.
11
Grease filter LED (F)
LED F will start to flash when it is time
to clean the grease filter.
Cleaning will be necessary after 40
working hours. Always comply with the
maintenance instructions for the grease
filter.
Charcoal filter LED (C)
The charcoal filter LED C will start to
flash when the charcoal filter needs to
be replaced.
This operation is necessary after
approximately 160 working hours.
Resetting the saturation indicator
After cleaning or replacing the filters,
press button 5 for 3 seconds until the
grease filter LED F or the charcoal filter
LED C stops flashing.
GB
12
electr
olux control panel
electrolux
Model EFC 9673
GB
b
1
2
3
7
a
4
5
6
1. Light switch, ON/OFF
2. Mains switch, ON/OFF
stand
Press for less than 1 1/2 seconds and the cooker hood goes into the "stand
by
by" position (dot “a” on display is illuminated).
Press for more than 1 1/2 seconds and the cooker hood turns OFF, ALL the
controls (except the light push button) are disabled (the display is off).
Press again for more than 1 1/2 seconds to reset the cooker hood to "stand
by".
3. Filters saturation rreset
eset key: see the relative text on the following pages.
4. Start and choice of motor speed 1-2-3-1-2...
5. Intensive speed ON/OFF: The Intensive speed runs for 5 minutes:
If the hood is on when the Intensive speed is activated, the hood will revert to
previous speed after 5 minutes. If the hood is off when the Intensive speed is
activated, the hood will automatically turn off after 5 minutes.
The letter P appears on the display and the remaining time (the dot “b” on
display is flashing), if interrupted an acoustic signal is heard.
6. Self-T
imer ON/OFF: times all the speed levels (the dot “a” on display is
Self-Timer
flashing), and then the cooker hood switches off:
The self-timer is set as follows:
1st speed level 20 minutes
2nd speed level 15 minutes
3rd speed level 10 minutes
The display shows the remaining operation time, at the end of the time an
acoustic signal is heard. Depressing the push-button again exits the function.
7. Display
Should the hood or the controls fail to operate: disconnect the power supply for at
least 5 seconds. After reconnecting the power supply wait 15 seconds and then
check that the cooker hood is now operating correctly.
electrolux control panel
Gr
ease and char
coal filter
Grease
charcoal
maintenance indicator
This hood is fitted with a device that
indicates when it is necessary to clean
the grease filter or the charcoal filter (if
the hood is used in the recirculation
version with a charcoal filter).
On delivery, the hood is not supplied
with a charcoal filter, so the saturation
indicator will be disabled.
If the hood is to be used with a
charcoal filter, the saturation
indicator light must be enabled as
follows:
OFF
Set in "OFF
OFF" the hood.
Press buttons 3 and 4 simultaneously
and hold them for 3 seconds. At first
only the grease filter LED F will light up,
but when the charcoal filter LED C
lights up the saturation indicator will be
enabled.
To disable it: Press buttons 3 and 4
again simultaneously and hold
them for 3 seconds, until the charcoal
filter LED goes out.
13
Grease filter LED (F)
LED F will start to flash when it is time
to clean the grease filter.
Cleaning will be necessary after 40
working hours. Always comply with the
maintenance instructions for the grease
filter.
Charcoal filter LED (C)
The charcoal filter LED C will start to
flash when the charcoal filter needs to
be replaced.
This operation is necessary after
approximately 160 working hours.
Resetting the saturation indicator
After cleaning or replacing the filters,
press button 3 for 3 seconds until the
grease filter LED F or the charcoal filter
LED C stops flashing.
GB
14
electr
olux control panel
electrolux
Maintenance and Care
GB
• Befor
e performing any maintenance operation, isolate the hood fr
om the
Before
from
electrical supply by switching of
emoving the
offf at the connector and rremoving
connector fuse.
Or if the appliance has been connected thr
ough a plug and socket, then the
through
plug must be rremoved
emoved fr
om the socket.
from
Air suction panels
EFC 9673 only
Remove the perimeter air suction
panels to access the grease filters.
The perimeter air suction panels are
attached to the cooker hood by a
series of pins and coupling springs
springs;
pull them outwards and detach them
from the fastening cable
cable.
Clean the perimeter air suction panels
as often as the grease filters (for more
information about gentle cleaning
methods, read the paragraph
“Cleaning” in the pages that follow).
When refitting the perimeter air suction
panels, ALWAYS reattach the fastening
cables.
Make sure the panels are attached to
the cooker hood properly (snapfastened).
x4
electrolux maintenance and care
15
Metal gr
ease filter
grease
• The purpose of the grease filters is to
absorb grease particles which form
during cooking and it must always be
used, either in the external extraction
or internal re-circulation function.
GB
Attention: the metal grease filters
must be removed and washed, either
by hand or in the dishwasher, every
four weeks.
Removing the metal gr
ease filter
grease
• Use the spring handle and remove
the filter downward.
Hand washing
Soak grease filters for about one hour
in hot water with a grease-loosening
cleaner, then rinse off thoroughly with
hot water. Repeat the process if
necessary. Refit the grease filters
when they are dry.
Dishwasher
Place grease filters in the dishwasher.
Select most powerful washing
programme and highest temperature,
at least 65°C. Repeat the process.
Refit the grease filters when they are
dry.
When washing the metal grease filter
in the dishwasher a slight
discolouration of the filter can occur,
this does not have any impact on its
performance.
• Clean the inner housing using a hand
hot solution only(never use caustic
detergents, abrasive powders or
brushes).
16
GB
electr
olux maintenance and care
electrolux
Char
coal filter
Charcoal
• The charcoal filter should only be
used if you want to use the hood in
recirculation mode.
• To do this you will need an original
charcoal filter (available from your
local Service Force Centre).
eplacing the char
coal filter
• Cleaning/r
Cleaning/replacing
charcoal
Unlike other charcoal filters, the
LONGLIFE charcoal filter can be
cleaned and reactivated.
With normal use the filter should be
cleaned every second month (when
using the hood 2.5 hours per day,on
avarage). The best way to clean the
filter is in the dishwasher. Use normal
detergent and choose the highest
temperature (65º C). Wash the filter
separately so that no food parts gets
stuck on the filter and later causes bad
odours. To reactivate the charcoal, the
filter should be dried in an oven for 10
minutes with a maximum temperature
of 100º C.
After approximately three years of use,
the charcoal filter should be replaced
with a new one, as the odour reduction
capacity will be reduced.
• Fitting
Position the carbon filter inside the
hood to cover the protection grill of
the motor.
Fix the filter with 2 lateral knobs.
emove proceed in the reverse
• To rremove
order.
• Always specify the hood model code
number and serial number when
ordering replacement filters. This
information is shown on the rating
plate located on the inside of the unit.
• The charcoal filter can be ordered
from your local Service Force Centre.
electrolux maintenance and care
17
War
ning
arning
GB
• Failure to observe the instructions on
cleaning the unit and changing the
filters will cause a fire hazard. You are
therefore strongly recommended to
follow these instructions.
• The manufacturer declines all
responsibility for any damage to the
motor or any fire damage linked to
inappropriate maintenance or failure
to observe the above safety
recommendations.
Changing the light bulb(s)
om
• Disconnect the cooker hood fr
from
the mains supply
supply..
• Prior to touching the light bulbs
ensur
e they ar
e cooled down.
ensure
are
• EFC 9670-6670 Model: remove the
overhead light, removing the fixing
clips.
• All models: Replace the old bulb with
a new one of the same type.
• EFC 9670-6670 Model: mount the
overhead light again and fix it in its
place with the clips.
• If the light does not come on, make
sure the bulb has been inserted in
correctly before contacting your local
Service Force Centre.
EFC 9671 - 6671- 9673: 20W max
GU4 - 12 V - Ø 35mm - 30° - Dichroic
EFC 9670-6670: 11W max - G23
18
electr
olux maintenance and care
electrolux
Cleaning the hood
GB
• Clean the outside of the hood using a
damp cloth and a solution of water
and mild washing up liquid.
• Never use corrosive, abrasive or
flammable cleaning products or
products containing bleach.
• Never insert pointed objects in the
motor’s protective grid.
• Only ever clean the switch panel and
filter grill using a damp cloth and mild
washing up liquid.
• Clean all the plastic parts with a soft
cloth soaked in warm water and
neutral soap.
• It is extremely important to clean the
unit and change the filters at the
recommended intervals. Failure to do
so will cause grease deposits to build
up that could constitute a fire hazard.
electrolux special accessories
19
Special accessories
GB
Char
coal filter Type 967
Charcoal
Remote contr
ol RM 6940
control
E-Nr. 942 122 002
Something Not Working
If your appliance fails to work properly please carry out the following checks.
Symptom
Solution
The cooker hood will not start...
Check that: The hood is connected
to the electricity supply.
Check that a fan speed has been
selected.
The cooker hood is not working
Check that: The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented to
allow the entry of fresh air.
If set up for recirculation, check that
the charcoal filter is still effective.
If set up for extraction, check that the
ducting and outlets are not blocked.
The cooker hood has switched off
during operation...
The safety cut-out device has been
tripped. Turn off the hob and then wait
for the device to reset. If the hood has
been installed below the heights
indicated in the installation instructions
the motor will cut-out frequently which
will damage the hood.
If after all these checks, the problem persists, contact your local Service Centre,
quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for any inguarantee service calls.
In-guarantee customers should ensure that the above checks have been made as
the engineer will make a charge if the fault is not a mechanical or electrical
breakdown.
20
electr
olux installation
electrolux
Installation
GB
Technical Details
EFC 9670(6670) EFC 9671(6671)
EFC 9673
Height (Extract. mode):
73-116
73-116
73-116
Height (Recirc. mode):
84,5-126
84,5-126
84,5-126
Width:
89,8 (59,8)
89,8 (59,8)
89,8
Depth:
45
45
45
Maximum absorbed power: 185 W
310 W(290 W)
310 W
Motor:
170 W
250 W
250 W
Lighting:
11 W
3 x20 W (2 x 20 W) 3 x20 W
Length of the cable:
150 cm
150 cm
150 cm
Electrical connection:
220-240 V
220-240 V
220-240 V
Fuse rating:
5A T
5A
T
5AT
5A T
Dimensions (in cm):
Mounting accessories included
1 deflector (with extensions)
1 Allan wrench for torx screws
1 fixing bracket for motor unit
1 support bracket for flues (3 pieces to assemble)
5 screws 5 x 45 mm
5 dowels Ø 8 mm
2 screws 2.9 x 6.5
8 screws 3.5 x 6.5
4 screws 4 x 8
electrolux installation
21
Electrical connection
(not for UK)
Electrical connection for
UK only
Safety war
nings for the electrician
warnings
Before connecting the appliance to the
power supply, check that the voltage
indicated on the rating plate
corresponds to the mains power supply
available. Appliances fitted with a plug
can be connected to any standard
power socket within easy access.
Should it be necessary to provide a
fixed connection, the hood must only
be installed by an electrician authorised
by the local electricity board. When
installing, an omnipolar disconnector
with a distance of at least 3 mm
between contacts must be provided.
Fixed connection of the appliance must
only be carried out by an authorised
electrician.
Safety war
nings for the electrician
warnings
Connect the hood to the mains supply
via a double pole switch which has 3
mm minimum separation between the
contacts.
The switch must be accessible at all
times.
The following is valid in the United
Kingdom only:
- the wire which is coloured green and
yellow must be connected to the
terminal which is marked with the
),
letter E or by the earth symbol (
or coloured green or green and
yellow;
- the wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black, - the wire which is coloured brown
must be connected to the terminal
which is marked with the letter L or
coloured red.
GREEN & YELLOW
5AT
BROWN
BLUE
CORD CLAMP
GB
22
GB
electr
olux installation
electrolux
B
First decide which functioning
version is better for you
If you decide to use the hood in
exhausting version we suggest you
position the upper section of the
chimney so that the oulet slots are not
visible once installation has ended, on
the contrary if it is decided to use the
hood in recycling version BE SURE that
the side with the slots is upright (see
also A-B-C sequence).
180°
A
C - OK!
4 x Ø 4x8
G
=
Assembling the chimney flue
support/bracket (3 parts)
The three parts should be fixed with 4
screws, the support extension is
adjustable and should correspond to
the internal width of the telescopic
chimney flue.
X
=
X
=
X
=
F
Assembling the deflector (3 parts –
only for filter version):
The three parts should be fixed with 2
screws, the deflector extension is
adjustable and should correspond to
the width of the chimney flue support,
to which it is then fixed.
6x
Ø 3,5 x 6,5
F
G
electrolux installation
23
Installation
GB
Make sur
e that the cooker hood is disconnected fr
om the power supply befor
e
sure
from
before
carrying out the installation.
Remove the perimeter air suction panels (EFC 9673 only) and the grease filters.
1). Position
• Mark a central line on the wall to facilitate the installation procedure (1
the drilling template so that the median line printed on it corresponds to the
central line marked previously, and so that the lower side of the template
2).
corresponds to the lower part of the cooker hood once it has been fitted (2
• Make 3 holes with Ø 8 mm (2 on top and 1 underneath) and fit 3 rawl plugs into
3).
them (3
4).
• Fix the motor assembly support bracket in place using 2 screws (4
• Make two holes with Ø 8 mm near the ceiling and use them to fix the support
bracket of flue G in place (use the bracket as a template – rest it against the wall
5) (install deflector
which joins onto the ceiling). Insert 2 rawl plugs into the holes (5
F underneath the bracket using 4 screws if you wish to use the cooker hood as
6).
a filter version) and fix the bracket in place using 2 screws (6
7) and adjust its position (8-9
8-9
• Fit the cooker hood (7
8-9).
10
• Fix the cooker hood in place (10
10).
11
• Install the exhaust tube (11
11) leading from cooker hood exhaust outlet B to the
outside environment (ducted version) or deflector F (filter version).
12
• Perform all necessary electrical connections (12
12).
24
GB
electr
olux installation
electrolux
4 x Ø 3,5x6,5
G
F
5
G
2 x Ø 5x45
2xØ8
6
12
1
11
2
7
2xØ8
3
B
4
2x
Ø 5x45
3
8
9
10
1 x Ø 5x45
1xØ8
electrolux installation
25
13
• Pull out the upper flue and, at the top, fix it to bracket G using 2 screws (13
13).
14
• Fix the lower flue in place from inside the cooker hood using 2 screws (14
14).
Mount the grease filter and (EFC
only) the perimeter air suction panels.
EFC 9673 only
EFC 9673-EFC 9671-EFC 6671
Connect the hood to the mains electricity (EFC
6671:: wait
about 15 seconds, the time needed to calibrate the electronic device that controls
the functioning of the hood), and check, finally, that it is functioning well.
GB
26
electr
olux installation
electrolux
GB
G
2 x Ø 2,9x6,5
13
13
14
2 x Ø 3,5x6,5
14
14
electrolux
77
78
electr
olux
electrolux
LI217A Ed. 01/07