Craftsman 973.113451 Operator`s manual

Operator's Manual
II:RRFTSMRN'I
318 in., 19.2 VOLT CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
973.113451
Save this manual for
future reference
• Safety
• Features
_, CAUTION:
Read and follow all
Safety Rules and Operating Instructions
before first use of this product,
Customer
Help Line: 1-800-932-3168
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
visit the Craftsman web page: www.sears.com
983000-094
11-02
• Operation
• Maintenance
• Parts List
Estates,
IL 60179
USA
•
Warranty .........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
3
•
General Safety Rules And Specific Safety Rules ......................................................................................................
•
Important Safety Instructions For Charger .....................................................................................................................
5
•
Symbols ..........................................................................................................................................................................
6
•
Product Specifications ....................................................................................................................................................
7
•
Features .....................................................................................................................................................................
7-8
•
Operation ..................................................................................................................................................................
9-14
•
Maintenance And Accessories .....................................................................................................................................
15
•
Exploded View And Repair Parts List ..........................................................................................................................
17
•
Parts Ordering / Service ...............................................................................................................................................
18
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
3-4
3/8 In. CORDLESS DRILL-DRIVER
If this rRRFTSMRH 3/8 in. Cordless Drill-Driver fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES,
and Sears will repair it, free of charge.
If this rRRFTSMRN 3/8 in. Cordless Drill-Driver is used for commercial or rental purposes, this warranty applies for only
90 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
_k
Look for this symbol
involved.
to point out important
safety precautions.
It means attention!!!
Your safety is
_kWARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
Your drill-driver has many features for making your drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this drill-driver making it easy to
maintain and operate.
,_
_i
Personal
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE
Work Area
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
•
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving pads.
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.
Electrical
Safety
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
INSTRUCTIONS
•
CAUTION: Carefully read through this entire
operator's manual before using your new drill-driver.
Pay close attention to the General Safety Rules,
Specific Safety Rules and Symbols, Wamings and
Cautions. If you use your drill-driver properly and only
for it's intended use, you will enjoy years of safe,
reliable service.
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal
injury.
Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables
better control of the tool in unexpected situations. Do
not use on a ladder or unstable support.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
MODEL
BATTERY PACK
CHARGER
973.113451
Item No. _ 11375
Item No.9 11041
(1310715)
(1425301)
•
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
3
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Tool Use and Care
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
•
Maintain tools with care. Keep cutUng tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
•
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is
•
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poody maintained tools.
dangerous and must be repaired.
•
Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may create a risk of injury
when used on another tool.
•
•
•
Disconnect battery pack from tool or place the switch
in the locked or off position before malting any adjustments, changing accessories, or stodng the tool. Such
preventivesafety measures reduce riskof startingthe tool
accidentally.
Store idle tools out of reach of children and other
Service
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
untrained persons. Tools are dangerous in the hands
of untrained users.
When
other
nails,
make
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
battery pack is not in use, keep it away from
metal objects like: paper clips, coins, keys,
screws, or other small metal objects that can
a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
Rules
fire or heat. This will reduce the risk of explosion and
possible injury.
For Safe Operation
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
_1=
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
Important
Rules for Battery Tools
•
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing accessories. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not place battery tools or their batteries near
WARNING:
Batteries vent hydrogen gas and can
explode in the presence of a source of ignition, such
as a pilot light. To reduce the risk of serious personal
injury, never use any cordless product in the presence of open flame. An exploded battery can propel
debris and chemicals. If exposed, flush with water
immediately.
•
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
•
For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
_1= WARNING: Never use a battery that has been
dropped or received a sharp blow. A damaged battery
is subject to explosion. Properly dispose of a dropped
battery immediately. Failure to heed this warning can
result in serious personal injury.
•
Save these instructions. This manual contains
important safety and operating instructions for
charger. Following this rule will reduce the risk of
electric shock, firs, or serious personal injury.
•
Before using battery charger, read all Instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
_IL CAUTION: To reduce risk of injury, charge only
nickel-cadmium type rechargeable batteries.
Other types of batteries may burst causing personal injury and damage. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
n
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
•
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
Use of an attachment not recommended
•
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
_,
DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY
TERMINAL.
or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
•
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
•
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25'
50'
100'
Cord Size (AWG)
16
16
16
Note: AWG = American Wire Gage
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
_h WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
rain
Minutes
Time
"_
Alternating Current
Type or a characteristic of current
--=
Direct Current
Type or a characteristic of current
no
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes,
surface speed, orbits etc. per minute
,_
Safety Alert Symbol
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
Wet Conditions Alert
Do
not expose to rain or use in damp
locations.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding, The safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL
A
MEANING
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING:
Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION:
Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock
and personal injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
SAVE THESE
INSTRUCTIONS
6
DRILL-DRIVER
973.113451
Chuck
3/8 in. Keyless
Motor
DC Motor 19.2 Volt
Rating
120 V, 60 Hz, AC only
Gear Train
Two Speed
Charging Voltage
7.2 - 24 Volt
No Load Speed
0-400 RPM (Low)
0-1400 RPM (High)
Charge Rate
1 Hour
Clutch
24 Positions
Maximum Torque
400 in.lb.
KNOW
YOUR DRILL-DRIVER
CHARGER
Item No. 9 11041
(1425301)
BATTERY
PACK
Item No. _911375
(1310715)
FORWARD/REVERSE
SELECTOR
See Figure 1.
(DIRECTION OF ROTATION SELECTOR)
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
Your drill-driver has a forward/reverse selector located
KEYLESS
above the switch trigger.
WRIST
STRAP
CHUCK
Your drill-driverhas a keyless chuck that allows you to hand
tighten or release drill bit in the chuck jaws.
A wrist strap is provided to reduce the chances of
dropping your drill-driver. Place one hand through the wrist
strap when carrying tool.
SWITCH
BIT STORAGE
To turn your drill-driver ON, depress the switch trigger.
When not in use, bits provided with your drill-driver can be
placed in the storage area located on the bottom of the
motor housing.
Release switch trigger to turn your drill-driver OFF.
SWITCH
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
VARIABLE
To keep drill bit level during drilling operations, a level is
located on the top and end of the motor housing.
SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
TWO SPEED
LEVEL
GEAR TRAIN
Your drill-driver has a two speed gear train designed for
drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed.
_11 WARNING: If any parts are missing, do not operate
your drill-driver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
TWO-SPEED
GEARTRAIN(HI-LO)
LEVEL
TORQUE
ADJUSTMENT
RING
KEYLESS
CHUCK
LEVEL
REARVIEW
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
SWITCH
TRIGGER
BIT
STORAGE
SCREWDRIVER
BITS
BATTERYPACK
SHOWNINTOOL
BATTERYPACK
SHOWNINCHARGER
WRISTSTRAP
CHARGER
RED LED ONINDICATES
GREENLED ONAFTERFASTCHARGING
CYCLE,INDICATESFULLYCHARGEDBATFERY
PACKANDIN TRICKLECHARGEMODE,
YELLOWANDGREENLEDSON INDICATESDEEPLY
DISCHARGEDOR DEFECTIVEBATTERYPACK.
Fig. 1
CHARGER
See Figure1.
Your charger has a "key hole" hanging feature for convenient, space saving storage. Screws should be installed so that
center distances are 4-1/2 inches apart.
8
_i
WARNING:
Do not allow familiarity with your drilldriver to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
BA'B'ERY
PACK
The battery pack for your tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until light on front of charger changes
from red to green.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
CHARGING
BATFERY
PACK
See Figure I.
•
Charge battery pack only with the charger provided.
•
Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
•
Connect charger to power supply.
•
Place battery pack in charger aligning raised rib on
battery pack with groove in charger. See Figure I.
•
Press clownon battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
•
Normally, the red LED on charger will come on. This
indicates charger is in fast charging mode.
•
Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is in
trickle charge mode. Note: Green LED will remain on
until battery pack is removed from charger or charger
is disconnected from power supply.
•
If both yellow and green LED come on, this indicates a
deeply discharged or defective battery pack.
Allow battery pack to remain in charger for 15 to 30
minutes. When battery pack reaches normal voltage
range, red LED should come on.
If red LED does not come on after 30 minutes, this
indicates a defective battery pack and should be
replaced.
•
After normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack.
•
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
Do not place charger and battery pack in an area of
extreme heat or cold. It will work best at normal room
temperature.
Note: Charger and battery pack should be placed in a
location where the temperature is more than 50°F but
less than IO0°F.
When batteries become fully charged, unplug charger
from power supply and remove the battery pack.
LED FUNCTIONS
OF CHARGER
LED WILL BE ON TO INDICATE STATUS
CHARGER
AND BA'n'ERY PACK:
OF
•
Red LED on = Fast charging mode.
•
Green LED on = Fully charged and in trickle charge
mode.
•
Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of or below normal temperature range.
•
Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
No LED on = Defective charger or battery pack.
CAUTION:
To prevent damage to battery pack,
remove battery pack from charger immediately if no
LED comes on. Return battery pack and charger to
your nearest Sears Service Center for checking or
replacing. Also, if you are removing battery pack from
charger and no LEDs are on, return both battery pack
and charger to your nearest Sears Service Center.
Do not insert another battery pack into charger. A
damaged charger may damage a battery pack.
IMPORTANT
INFORMATION
HOT BATTERY PACK
FOR RECHARGING
When using your drill-driver continuously, the batteries in
your battery pack will become hot. You should let a hot
battery pack cool down for approximately 30 minutes
before attempting to recharge. When the battery pack
becomes discharged and is hot, this will cause the green
LED to come on instead of the red LED. After 30 minutes,
reinsert battery pack in charger. If green LED continues to
remain on, return battery pack to your nearest Sears
Repair Center for checking or replacing.
Note: This situation only occurs when continuous use of
your drill causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
BATTERY PACK" for normal recharging of batteries. If
the charger does not charge your battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Sears Repair Center for electrical
check.
IMPORTANT
INFORMATION
COOL BATTERY
PACK
FOR RECHARGING
If battery pack is below normal temperature range, the
green LED on charger will come on. Allow battery pack to
reach normal temperature, then the red LED will come on.
Note: Refer to "CHARGING BATTERY PACK" for
normal recharging of batteries. If the charger does not
charge your battery pack under normal circumstances,
return both the battery pack and charger to your nearest
Sears Repair Center for electrical check.
TO INSTALL
SWITCH
See Figure 2.
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE
PACK
•
Lock switch trigger on your drill by placing the direction
of rotation selector in center position. See Figure 5.
•
Place battery pack in your drill. Align raised rib on
battery pack with groove inside drill. See Figure 4.
FORWARD/REVERSE
SWITCHTRIGGER
BATTERY
BATTERY
PACK
Fig. 2
SPEED
LATCHES
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed is
controlled by the amount of switch trigger depression.
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
"I3NO-SPEED
GEAR TRAIN
_X_DEPRESSLATCHESTO
See Figure 3.
Your drill has a two-speed gear train designed for dritling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of your drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
TWO SPEED
GEARTRAIN(HI-LO)
RELEASEBATTERYPACK
•
,_ll
LO
SPEED
Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in drill
before beginning operation.
CAUTION:
When placing battery pack in your drill,
be sure raised rib on battery pack aligns with groove
inside drill and latches snap into place properly.
improper assembly of battery pack can cause
damage to internal components.
TO REMOVE
•
SPEED
•
•
Fig. 3
10
Fig. 4
BATTERY
PACK
Lock switch trigger on your drill by placing the direction
of rotation selector in center position. See Figure 5.
Locate latches on side of battery pack and depress to
release battery pack from your drill. See Figure 4.
Remove battery pack from your drill,
SWITCH
LOCK
KEYLESS
CHUCK
See Figure5.
See Figure 6.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector (Forward/Reverse Selector)
in center position. Note: When selector is in center
position, switch trigger is locked.
Your drill has a keyless chuck. As the name implies, you can
hand tighten or release drill bits in the chuck jaws. Grasp and
hold the collar of the chuck with one hand. Rotate the chuck
body with your other hand. The arrows on the chuck
indicate which direction to rotate the chuck body in order to
LOCK (tighten) or UNLOCK (release) the drill bit.
.EVE..
""
•
FORWARD
_1
UN'0CK
TRIGGER
CHUCK
Fig. 5
LOCK
(TIGHTEN)
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
CHUCK
BODY
•
Fig. 6
_L
REVERSIBLE
See Figure5.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
,_
CHUCK
COLLAR
CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
11
WARNING:
Do not hold chuck body with one hand
and use power of the drill to tighten chuck jaws on
drill bit. Chuck body could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
INSTALLING
BITS
REMOVING
BITS
See Figure 7.
See Figure 7.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See F/#ure 5.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Fi#ure 5.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Loosen the chuck jaws from drill bit.
•
To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other
hand. Note: Rotate chuck body in the direction of the
arrow marked UNLOCK to loosen chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
•
Insert drill bit straight into chuck the full length of the
jaws as shown in Figure 7.
•
Tighten the chuck jaws on drill bit.
DRILLBIT
UNLOCK
(RELEASE)
CHUCK
COLLAR
ADJUSTABLE
TORQUE
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and the
size of screw you are using.
TO ADJUST
CHUCKJAWS
LOCK
(TIGHTEN)
RIGHT
•
•
,_
CHUCK
BODY
•
Identify the twenty four torque indicator settings located
on the front of your drill. See Figure 9.
•
Rotate adjusting ring to the desired setting.
• 1-4
For driving small screws.
•
For driving screws into soft
material.
5-8
• 9-12
For driving screws into soft and hard
materials.
,13-16
For driving screws in hard wood,
• 17- 20
For driving large screws.
• 21- ,l_
For heavy drilling.
Fig. 7
To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
Note: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten chuck jaws.
Do not use a wrench to tighten or loosen the chuck
jaws.
TORQUE
TO DECREASE
TORQUE
ADJUSTING
RING
WARNING:
Make sure to insert drill bit straight into
chuck jaws. Do not insert drill bit into chuck jaws at
an angle then tighten, as shown in Figure 8. This
could cause drill bit to be thrown from drill, resulting
in possible serious personal injury or damage to the
chuck.
TOINCREASE
TORQUE
Fig. 8
12
Fig. 9
BIT STORAGE
DRILLING
See Figure I0.
=GeeFigure 12.
When not in use, bits provided with your drill can be
placed in the storage area located on the bottom of your
drill as shown in Figure tO.
LEVEL
SCREWDRIVER
Brf
STORAGEAREA
_
Fig. 10
WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
Fig. 12
LEVEL
See Figure I
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
A convenient feature provided with your drill is a level. It
is recessed in the motor housing on top and end of your
drill. It can be used to keep drill bit level during drilling
operations.
with clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
_
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
Fig. 11
13
CHUCK
REMOVAL
•
Gee F/_Tures13, 14, and 15.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 5.
•
Insert a 5/16 in. or larger hex key into the chuck of your
drill and tighten the chuck jaws securely.
•
Tap the hex key sharply with a mallet in a clockwise
direction. See F'igufe 13. This will loosen the screw in
the chuck for easy removal.
Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. It can
now be unscrewed by hand. See Fl'_ufe 15.
MALLET
MALLET
CHUCKJAWS
Fig. 15
TO RETIGHTEN
HEXKEY
•
"IL._
_
KEYLESS
CHUCK
A LOOSE
CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
To tighten, follow these steps:
Fig. 13
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. Gee
Figure 14.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See F/pure 5.
•
Open the chuck jaws.
Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
Note: The screw has left hand threads.
SCREWDRIVER
•
Open the chuck jaws and remove hex key.
•
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
Fig. 14
14
,_
Do not abuse power tools. Abusive practices can
damage tool as well as workpiece.
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product damage.
Only the parts shown on parts list, page 17, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic pads. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_L
_i
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
BATTERIES
Your drill's battery pack !s equipped with nickel-cadmium
rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing.
•
Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery life.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
•
All batteries gradually lose their charge. The higher
the femperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
To preserve natural resources, please
recycle or dispose of batteries properly.
BATTERY
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
A
Consult your local waste authority for information
regarding available recycling and/or disposal options.
The following recommended
PACK REMOVAL
AND PREPARATION
FOR RECYCLING
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
accessories are currently available at Sears Retail Stores.
•
6-Pc. Extra Length Magnite Power Bit Set
•
High Speed Bits ...... 1/2 in. Max.
•
30-Pc. Power Screwdriver/Nutdriver
Set and Case
•
Wood Boring Bits ...... 1-1/2 in. Max.
•
17-Pc. Power Screwdriver/Nutdriver
Set and Case
_lL WARNING:
The use of attachments or accessories not listed might be hazardous.
15
16
CRAFTSMAN
318 in., 19.2 VOLT CORDLESS
DRILL-DRIVER
- MODEL
NO. 973.113451
in all correspondence regarding your 3/8 in., 19.2 VOLT CORDLESS DRILL-DRIVER or when ordering
I repair
he model
number will be found on a plate attached to the motor housing. Always mention the model number ]
parts.
SEE BACK
PAGE
FOR PARTS
ORDERING
INSTRUCTIONS
2
1
4
3
PARTS LIST
Key
No.
Part
Number
1
616478-003
Screw (Special) ......................................................................
1
2
6903304
Description
Qty.
Chuck .....................................................................................
1
3
*Item No. _. 11375
Battery Pack (1310715) .........................................................
1
4
* Item No. _ 11041
Charger (1425301 ) .................................................................
1
3073046
Carrying Case - Not Shown ..................................................
1
983000-094
Operator's Manual
5
* Can Be Purchased Through RSOS (Retail Special Order System)
17
Your Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
® (1-800-469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
1-800-361-6665
Au Canada
(Canada)
pour service
en fran_ais:
1-800-LE-FOYER
s_
Mc
(1-800-533-6937)
www.sears.ca
(1-888-784-6427)
® Registered Trademark / TM Trademark / SMService Mark of Sears, Roebuck and Co.
® Marca Registrada / ru Marca de F_bdea / sM Marca de Servicio de Sears, Roebuck and Co.
Mc Marque
de commerce
/ MD Marque
d_pos_e
de Sears,
Roebuck
and Co.
© Sears,
Roebuck
and Co.