Audiovox D2016 - DVD Player - 10.2 Operating instructions

AV Receiver
VSX-823-K
Operating Instructions
CAUTION
VENTILATION CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 40 cm at top, 20 cm at rear, and 20 cm at each
side).
D3-4-2-1-1_B1_En
WARNING
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
.
2
.
WARNING
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-1-7c*_A1_En
D3-4-2-2-2a*_A1_En
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
Operating Environment
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
Voltage selector
You can find the voltage selector switch on the rear
panel of multi-voltage models.
The factory setting for the voltage selector is
220-240 V. Please set it to the correct voltage for
your country or region.
• For Taiwan, please set to 110-127 V before using.
• For Mexico, please set to 110-127 V before using.
Before changing the voltage, disconnect the AC power
cord. Use a medium size screwdriver to change the
voltage selector switch.
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
D41-6-4_A1_En
K041_A1_En
(Symbol examples for batteries)
Medium size screwdriver
These symbols are only valid
in the European Union.
Pb
D3-4-2-1-5*_A2_En
For Taiwan exclusively
K058c_A1_En
Taiwanese two pin flat-bladed plug
K056_A1_En
3
Contents
Thank you for buying this Pioneer product. Please read
through these operating instructions so you will know how to
operate your model properly.
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Checking what’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Flow of settings on the receiver . . . . . . . . . . . . . . 6
01 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Loading the batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operating range of remote control . . . . . . . . . . . . . . . . 10
02 Connecting your equipment
Determining the speakers’ application . . . . . . . . . . . . . . .
Some tips for improving sound quality . . . . . . . . . . . . .
Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . . . .
Switching the speaker terminal . . . . . . . . . . . . . . . . . . .
Making cable connections . . . . . . . . . . . . . . . . . . . . . . . .
HDMI cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital audio cables. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Video cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About video outputs connection. . . . . . . . . . . . . . . . . . . .
Connecting a TV and playback components . . . . . . . . . . .
Connecting using HDMI . . . . . . . . . . . . . . . . . . . . . . . .
Connecting your TV with no HDMI input . . . . . . . . . . . .
Connecting optional Bluetooth® ADAPTER . . . . . . . . . . .
Connecting to the network through LAN interface . . . . . .
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using external antennas . . . . . . . . . . . . . . . . . . . . . . . .
Connecting an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use a dedicated cable to enjoy iPod video. . . . . . . . . . .
Connecting a USB device. . . . . . . . . . . . . . . . . . . . . . . . .
Connecting an MHL-compatible device . . . . . . . . . . . . . .
Connecting an HDMI-equipped component to the front
panel input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
13
13
13
13
14
14
14
14
15
15
16
17
17
18
18
18
19
19
19
20
20
03 Basic Setup
Before setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the TV format setting . . . . . . . . . . . . . . . . . . .
Automatically setting up for surround sound
(MCACC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other problems when using the Auto MCACC setup . . .
06 Playback with NETWORK features
21
21
21
22
04 Basic playback
Playing a source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the audio input signal . . . . . . . . . . . . . . . . . .
Playing an iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing back files stored on an iPod . . . . . . . . . . . . . . .
Basic playback controls. . . . . . . . . . . . . . . . . . . . . . . . .
Watching photos and video content . . . . . . . . . . . . . . .
Playing a USB device . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing back audio files stored on a USB memory
device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing back photo files stored on a USB memory
device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About playable file formats . . . . . . . . . . . . . . . . . . . . . .
Playing an MHL-compatible device. . . . . . . . . . . . . . . . . .
Bluetooth® ADAPTER for Wireless Enjoyment of
Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless music play. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pairing the Bluetooth ADAPTER and Bluetooth wireless
technology device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening to Music Contents of Bluetooth wireless
technology device with Your System . . . . . . . . . . . . . . .
AIR JAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Improving FM sound . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening to station presets . . . . . . . . . . . . . . . . . . . . . .
Naming preset stations . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the radio frequency step . . . . . . . . . . . . . . . .
23
23
25
25
25
25
26
26
26
27
27
28
28
28
29
29
29
30
30
30
30
30
05 Listening to your system
Choosing the listening mode . . . . . . . . . . . . . . . . . . . . . .
Auto playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening in surround sound . . . . . . . . . . . . . . . . . . . . .
Using the Advanced surround . . . . . . . . . . . . . . . . . . .
Using Stream Direct . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Sound Retriever . . . . . . . . . . . . . . . . . . . . . . . .
Listening with Acoustic Calibration EQ. . . . . . . . . . . . . . .
Better sound using Phase Control . . . . . . . . . . . . . . . . . .
Setting the Audio options . . . . . . . . . . . . . . . . . . . . . . . . .
4
31
31
31
32
32
33
33
33
34
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About playable DLNA network devices. . . . . . . . . . . . . .
Using AirPlay on iPod touch, iPhone, iPad, and
iTunes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the DHCP server function . . . . . . . . . . . . . . . . . .
Authorizing this receiver . . . . . . . . . . . . . . . . . . . . . . . .
About HTC Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playback with Network functions . . . . . . . . . . . . . . . . . . .
Basic playback controls . . . . . . . . . . . . . . . . . . . . . . . . .
Listening to Internet radio stations. . . . . . . . . . . . . . . . .
Playing back audio files stored on components on the
network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing back your favorite songs . . . . . . . . . . . . . . . . . .
The Network Setup menu . . . . . . . . . . . . . . . . . . . . . . . . .
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . .
Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network setting using Safari browser . . . . . . . . . . . . . .
Friendly Name setting using Safari browser. . . . . . . . . .
Firmware update using Safari browser. . . . . . . . . . . . . .
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About network playback . . . . . . . . . . . . . . . . . . . . . . . . . .
Content playable over a network . . . . . . . . . . . . . . . . . .
About playback behavior over a network . . . . . . . . . . . .
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About playable file formats . . . . . . . . . . . . . . . . . . . . . . . .
36
36
36
36
36
37
37
37
38
38
38
39
39
40
40
41
41
41
42
42
42
43
43
43
44
07 Home Menu
Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual speaker setup. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
X.Over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Distance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Input Assign menu . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Auto Power Down menu. . . . . . . . . . . . . . . . . . . . . . .
The Network Standby menu . . . . . . . . . . . . . . . . . . . . . . .
The MHL Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The OSD Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
45
45
46
46
47
47
47
47
47
48
48
Contents
08 Control with HDMI function
Making Control with HDMI connections. . . . . . . . . . . . . .
HDMI Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before using synchronization . . . . . . . . . . . . . . . . . . . . . .
About synchronized operations . . . . . . . . . . . . . . . . . . . .
Cautions on the Control with HDMI function . . . . . . . . . .
49
49
50
50
50
09 Controlling the rest of your system
Setting the remote to control other components . . . . . . .
Selecting preset codes directly. . . . . . . . . . . . . . . . . . . . .
Clearing all the remote control settings . . . . . . . . . . . . . .
Controls for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls for other components. . . . . . . . . . . . . . . . . . . . .
Preset Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
51
51
52
52
52
10 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NETWORK feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important information regarding the HDMI
connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MHL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTC Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . . .
Apple Lossless Audio Codec . . . . . . . . . . . . . . . . . . . . . .
About FLAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About messages displayed when using network
functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the main unit . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
56
57
58
58
58
58
59
59
59
59
59
60
60
60
5
Before you start
Checking what’s in the box
Please check that you’ve received the following supplied
accessories:
• Setup microphone
• Remote control
• AAA size IEC R03 dry cell batteries (to confirm system
operation) x2
• AM loop antenna
• FM wire antenna
• Power cord
• Quick start guide
• Safety Brochure
• SPEAKER CAUTION Sheet (English only)
• These operating instructions (CD-ROM)
Flow of settings on the receiver
The unit is a full-fledged AV receiver equipped with an
abundance of functions and terminals. It can be used easily
after following the procedure below to make the connections
and settings.
The colors of the steps indicate the following:
Required setting item
the on-screen automatic MCACC setup to set up
5 Use
your system
• Automatically setting up for surround sound (MCACC)
(page 21)

Setting to be made as necessary
-----------------------------------------the speakers
1 Connecting
Where you place the speakers will have a big effect on
the sound.
• Determining the speakers’ application (page 11)
• Connecting the speakers (page 12)
• Switching the speaker terminal (page 13)
Installing the receiver
• When installing this unit, make sure to put it on a level and
stable surface.
Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives off a
magnetic field). This may interfere with the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other movement
– in places that are very dusty
– in places that have hot fumes or oils (such as a kitchen)


the components
2 Connecting
For surround sound, you’ll want to hook up using a
digital connection from the Blu-ray Disc/DVD player to
the receiver.
• About video outputs connection (page 14)
• Connecting a TV and playback components (page 15)
• Connecting antennas (page 18)
• Plugging in the receiver (page 20)

On
3 Power
Make sure you’ve set the video input on your TV to this
receiver. Check the manual that came with the TV if you
don’t know how to do this.

4
The Input Assign menu (page 47)
(When using connections other than the recommended
connections.)
HDMI Setup (page 49)
(When the connected TV supports the HDMI Audio Return
Channel function.)
6
playback (page 23)
6 Basic
• Selecting the audio input signal (page 23)
• Playing an iPod (page 25)
• Playing a USB device (page 26)
• Choosing the listening mode (page 31)

the sound as desired
7 Adjusting
• Using the Sound Retriever (page 33)
•
•
•
•
Better sound using Phase Control (page 33)
Listening with Acoustic Calibration EQ (page 33)
Setting the Audio options (page 34)
Manual speaker setup (page 45)

maximum use of the remote control
8 Making
• Setting the remote to control other components
(page 51)
4
7
56
Chapter
1
Controls and displays
4
Front panel
1
2
3
4
5
6
7
8 9
10
7
19
25
11
12 13
14
15
1 INPUT SELECTOR dial
Selects an input source (page 23).
2 SPEAKERS
See Switching the speaker terminal on page 13.
The Speaker System setting may or may not be displayed,
depending on the input source you have selected.
3 MCACC indicator
Lights when Acoustic Calibration EQ (page 33) is on (Acoustic
Calibration EQ is automatically set to on after the Auto
MCACC setup (page 21)).
4 Receiver control buttons
DIMMER – Dims or brightens the display. The brightness
can be controlled in four steps.
DISPLAY – Switches the display of this unit. The listening
mode, sound volume, input name can be checked by
selecting an input source.
5 Character display
See Display on page 8.
16
17
20
21
26
27
22
28
23
29
21
29
24
30
18
6 Tuner control buttons
12 PHONES jack
BAND – Switches between AM, FM ST (stereo) and FM
MONO radio bands (page 29).
TUNER EDIT – Use with TUNE /, PRESET / and
ENTER to memorize and name stations for recall
(page 29).
TUNE / – Used to find radio frequencies (page 29).
PRESET / – Use to select preset radio stations
(page 30).
7 HDMI indicator
Blinks when connecting an HDMI-equipped component;
lights when the component is connected (page 15).
8 iPod iPhone iPad indicator
Lights when an iPod/iPhone/iPad is connected and iPod/USB
input is selected (page 25).
9 Remote sensor
Receives the signals from the remote control (see Operating
range of remote control on page 10).
10 MASTER VOLUME dial
11 STANDBY/ON
7
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers. The
listening mode when the sound is heard from the headphone
can be selected only from PHONES SURR, STEREO or
STEREO ALC mode (S.R AIR mode can be also selected with
ADAPTER input).
13 MCACC SETUP MIC jack
Use to connect a microphone when performing Auto MCACC
setup (page 21).
14 Listening mode buttons
AUTO SURROUND/STREAM DIRECT – Switches between
Auto surround mode (page 31) and Stream Direct
playback (page 32).
ALC/STANDARD SURR – Press for standard decoding
and to switch between the modes of 2 Pro Logic II and
NEO:6, and the Auto level control stereo mode (page 31).
ADVANCED SURROUND – Switches between the various
surround modes (page 32).
56
1
15 ECO
Switches between ECO Mode 1/ECO Mode 2. When ECO
Mode is turned ON, the display will go dark (page 32).
16 iPod iPhone iPad DIRECT CONTROL
Change the receiver’s input to the iPod and enable iPod
operations on the iPod (page 26).
17 iPod/iPhone/iPad terminals
Use to connect your Apple iPod/iPhone/iPad or USB mass
storage device as an audio source (page 18).
18 HDMI input/MHL connector
Use for connection to a compatible HDMI device (Video
camera, etc.) (page 20). An MHL-compatible mobile device
can also be connected here using a MHL cable (sold
separately) (page 19).
Display
19 PHASE
Lights when the Phase Control is switched on (page 33).
20 AUTO
Lights when the Auto Surround feature is switched on
(page 31).
21 Tuner indicators
ST – Lights when a stereo FM broadcast is being received
in auto stereo mode (page 29).
TUNE – Lights when a normal broadcast channel.
PRESET – Shows when a preset radio station is registered
or called.
MEM – Blinks when a radio station is registered.
kHz/MHz – Lights when the character display is showing
the currently received AM/FM broadcast frequency.
22 Speaker indicators
Shows if the speaker system is on or not (page 13).
23 Sleep timer indicator
Controls and displays
26 DTS indicators
DTS – Lights when a source with DTS encoded audio
signals is detected.
HD – Lights when a source with DTS-EXPRESS or DTS-HD
encoded audio signals is detected.
ES – Lights to indicate DTS-ES decoding.
96/24 – Lights when a source with DTS 96/24 encoded
audio signals is detected.
NEO:6 – When one of the NEO:6 modes of the receiver is
on, this lights to indicate NEO:6 processing (page 31).
27 Dolby Digital indicators
2 D – Lights when a Dolby Digital encoded signal is
detected.
2 D+ – Lights when a source with Dolby Digital Plus
encoded audio signals is detected.
2HD – Lights when a source with Dolby TrueHD encoded
audio signals is detected.
2PLII – Lights to indicate 2 Pro Logic II decoding. (see
Listening in surround sound on page 31 for more on this).
28 ADV.S.
Lights when one of the Advanced Surround modes has been
selected (see Using the Advanced surround on page 32 for
more on this).
29 SIGNAL SELECT indicators
DIGITAL – Lights when a digital audio signal is selected.
Blinks when a digital audio signal is selected and selected
audio input is not provided.
HDMI – Lights when an HDMI signal is selected. Blinks
when an HDMI signal is selected and selected HDMI input
is not provided.
30 DIR.
Lights when the DIRECT or PURE DIRECT mode is switched
on (page 32).
Lights when the receiver is in sleep mode (page 9).
24 PRESET information or input signal indicator
Shows the preset number of the tuner or the input signal type,
etc.
25 Character display
Displays various system information.
8
4
7
56
1
Controls and displays
• The following buttons are not used with this receiver:
Remote control
- PTY, SHIFT
1
2
3
4
11
RECEIVER SLEEP
SOURCE
RECEIVER
INPUT
1 SLEEP
Press to change the amount of time before the receiver
switches into standby (30 min – 60 min – 90 min – Off). You
can check the remaining sleep time at any time by pressing
SLEEP once.
2 RECEIVER
12
Switches the receiver between standby and on.
3
RECEIVER
Switches the remote to control the receiver (used to select the
white commands above the number buttons (MIDNIGHT,
etc)). Also use this button to set up surround sound (page 45)
or Audio parameters (page 34).
5
4 INPUT SELECT
Use to select the input source (page 23).
6
13
AUDIO
PARAMETER
ENTER
HOME
MENU
PTY
iPod CTRL
TUNE
PRESET
PRESET
7
TUNE
TOP
MENU
14
8
BAND
RETURN
MUTE
15
9
10
1
2
3
DISP
4
5
6
CH
7
8
9
CH
CLR
0
ENTER
SHIFT
RECEIVER
5 Input function buttons
Use to select the input source to this receiver (page 23). This
will enable you to control other components with the remote
control (page 51).
TOOLS
MENU
16
6 Listening mode buttons
AUTO/DIRECT – Switches between Auto surround mode
(page 31) and Stream Direct playback (page 32).
ALC/STANDARD SURR (VSX-828 only) – Press for
standard decoding and to switch between the modes of
2 Pro Logic II, 2 Pro Logic IIx, 2 Pro Logic IIz and
NEO:6, and the Auto level control stereo mode (page 31).
ALC/STANDARD SURR (VSX-528 only) – Press for
standard decoding and to switch between the modes of
2 Pro Logic II and NEO:6, and the Auto level control
stereo mode (page 31).
ADV SURR – Switches between the various surround
modes (page 32).
7 Receiver and component control buttons
The following button controls can be accessed after you have
selected the corresponding input function button (BD, DVD,
etc.).
Press RECEIVER first to access:
AUDIO PARAMETER – Use to access the Audio options
(page 34).
9
HOME MENU – Press to access the Home Menu
(page 45).
RETURN – Confirm and exit the current menu screen.
Press BD, DVD or DVR/BDR first to access:
TOP MENU – Displays the disc ‘top’ menu of a Blu-ray
Disc/DVD.
HOME MENU – Displays the HOME MENU screen.
RETURN – Confirm and exit the current menu screen.
MENU – Displays the TOOLS menu of Blu-ray Disc player.
Press TUNER first to access:
TOOLS – Memorizes stations for recall (page 29), also
used to change the name (page 30).
BAND – Switches between AM, FM ST (stereo) and FM
MONO radio bands (page 29).
Press iPod/USB first to access:
iPod CTRL – Switches between the iPod controls and the
receiver controls (page 25).
8 /// (TUNE /, PRESET /), ENTER
Use the arrow buttons when setting up your surround sound
system (page 45). Also used to control Blu-ray Disc/DVD
menus/options.
Use TUNE / can be used to find radio frequencies and
PRESET / can be used to select preset radio stations
(page 30).
9 Component control buttons
The main buttons (, , etc.) are used to control a component
after you have selected it using the input function buttons.
The controls above these buttons can be accessed after you
have selected the corresponding input function button (BD,
DVD and CD). These buttons also function as described
below.
Press RECEIVER first to access:
BASS +/–, TRE +/– – Use to adjust Bass or Treble.
• These controls are disabled when the listening mode is
set to DIRECT or PURE DIRECT.
• When the front speaker is set at SMALL in the Speaker
Setting (or automatically via the Auto MCACC setup)
and the X.Over is set above 150 Hz, the subwoofer
channel level will be adjusted by pressing BASS +/–
(page 46).
4
7
56
1
10 Number buttons and other component controls
Use the number buttons to directly select a radio frequency
(page 29) or the tracks on a CD, etc. There are other buttons
that can be accessed after RECEIVER is pressed. (For example
MIDNIGHT, etc.)
EQ – Press to switch on/off Acoustic Calibration EQ
setting (page 33).
PHASE – Press to switch on/off Phase Control (page 33).
SIGNAL SEL – Press to select the audio input signal of the
component to play back (page 23).
S.RETRIEVER – Press to restore CD quality sound to
compressed audio sources (page 33).
CH SELECT – Press repeatedly to select a channel, then
use LEV +/– to adjust the level (page 46).
LEV +/– – Use to adjust the channel level.
MIDNIGHT – Switches to Midnight or Loudness listening
(page 34).
SPEAKERS – See Switching the speaker terminal on
page 13.
DIMMER – Dims or brightens the display. The brightness
can be controlled in four steps.
During ECO mode, the brightness switches between 2
levels. If the dimmest level is selected, DIMMER will be
shown on the display. (Mode other than ECO: 4 levels, ECO
mode: 2 levels)
+Favorite – Press while a song is being played back or
stopped. The selected song is then registered in the
Favorites folder (page 38).
11 SOURCE
Press to turn on/off other components connected to the
receiver (page 51).
12 TV CONTROL buttons
These buttons are dedicated to control the TV assigned to the
TV button. Thus if you only have one TV to hook up to this
system assign it to the TV button (page 52).
 – Use to turn on/off the power of the TV.
INPUT – Use to select the TV input signal.
CH +/– – Use to select channels.
VOL +/– – Use to adjust the volume on your TV.
Controls and displays
13 ECO
Switches between ECO Mode 1/ECO Mode 2. When ECO
Mode is turned ON, the display will go dark (page 32).
14 VOLUME +/–
Use to set the listening volume.
15 MUTE
Mutes/unmutes the sound.
16 DISP
Switches the display of this unit. The listening mode, sound
volume.
• The Speaker System setting may or may not be displayed,
depending on the input source you have selected.
Loading the batteries
- When inserting the batteries, make sure not to damage
the springs on the battery’s (–) terminals. This can cause
batteries to leak or overheat.
Operating range of remote control
The remote control may not work properly if:
• There are obstacles between the remote control and the
receiver’s remote sensor.
• Direct sunlight or fluorescent light is shining onto the
remote sensor.
• The receiver is located near a device that is emitting
infrared rays.
• The receiver is operated simultaneously with another
infrared remote control unit.
30°
The batteries included with the unit are to check initial
operations; they may not last over a long period. We
recommend using alkaline batteries that have a longer life.
WARNING
• Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a heater.
This can cause batteries to leak, overheat, explode or catch
fire. It can also reduce the life or performance of batteries.
CAUTION
• Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
- Never use new and old batteries together.
- Insert the plus and minus sides of the batteries properly
according to the marks in the battery case.
- Batteries with the same shape may have different
voltages. Do not use different batteries together.
- When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
10
30°
7m
4
7
56
Chapter
2
Connecting your equipment
Determining the speakers’ application
• Refer to the chart below for placement of speakers you
intend to connect.
By connecting the left and right front speakers (L/R), the
center speaker (C), the left and right surround speakers (SL/
SR), the left and right surround back speakers (SBL/SBR) (or
the left and right front height speakers (FHL/FHR)), and the
subwoofer (SW), a surround sound system up to 7.1 channel
can be enjoyed.
The 5.1 channel surround system is the most commonly-used
in home theaters. To achieve the best possible surround
sound, install your speakers as shown below.
SW
FHL
FHR
C
L
R
30
30
120
SL
5.1 channel surround
system:
120
SR
60
SBL
SB
SBR
- Place the surround speakers at 120º from the center. If
R
L
C
SW
•
SR
SL
Some tips for improving sound quality
Where you put your speakers in the room has a big effect on
the quality of the sound. The following guidelines should help
you to get the best sound from your system.
• It is best to angle the speakers towards the listening
position. The angle depends on the size of the room. Use
less of an angle for bigger rooms.
•
•
•
•
•
•
you, (1) use the surround back speaker, and, (2) don’t use
the front height speakers, we recommend placing the
surround speaker right beside you.
- If you intend to connect only one surround back
speakers, place it directly behind you.
For the best stereo effect, place the front speakers 2 m to
3 m apart, at equal distance from the TV.
If you’re using a center speaker, place the front speakers at
a wider angle. If not, place them at a narrower angle.
Place the center speaker above or below the TV so that the
sound of the center channel is localized at the TV screen.
Also, make sure the center speaker does not cross the line
formed by the leading edge of the front left and right
speakers.
Surround and surround back speakers should be
positioned 60 cm to 90 cm higher than your ears and titled
slight downward. Make sure the speakers don’t face each
other. For DVD-Audio, the speakers should be more directly
behind the listener than for home theater playback.
Try not to place the surround speakers farther away from
the listening position than the front and center speakers.
Doing so can weaken the surround sound effect.
Place the left and right front height speakers at least one
meter directly above the left and right front speakers.
If you’re going to place speakers around your CRT TV, use
shielded speakers or place the speakers at a sufficient
distance from your CRT TV.
11
• The subwoofer can be placed on the floor. Ideally, the other
speakers should be at about ear-level when you’re listening
to them. Putting the speakers on the floor (except the
subwoofer), or mounting them very high on a wall is not
recommended.
• When not connecting a subwoofer, connect speakers with
low frequency reproduction capabilities to the front
channel. (The subwoofer’s low frequency component is
played from the front speakers, so the speakers could be
damaged.)
• After connecting, be sure to conduct the Auto MCACC
(speaker environment setting) procedure.
See Automatically setting up for surround sound (MCACC)
on page 21.
CAUTION
• Make sure that all speakers are securely installed. This not
only improves sound quality, but also reduces the risk of
damage or injury resulting from speakers being knocked
over or falling in the event of external shocks such as
earthquakes.
4
7
56
2
Connecting your equipment
Subwoofer
Connecting the speakers
Front right
Front left
Center
The receiver will work with just two stereo speakers (the front speakers in the diagram) but
using at least three speakers is recommended, and a complete setup is best for surround
sound.
Make sure you connect the speaker on the right to the right (R) terminal and the speaker on the
left to the left (L) terminal. Also make sure the positive and negative (+/–) terminals on the
receiver match those on the speakers.
You can use speakers with a normal impedance between 6  and 16 .
Be sure to complete all connections before connecting this unit to the AC power source.
LINE LEVEL
INPUT
7
56
Bare wire connections
1 Twist exposed wire strands together.
2 Loosen terminal and insert exposed wire.
3 Tighten terminal.
1
2
4
3
PREOUT
SUBWOOFER
10 mm
FRONT
R L
CAUTION
• These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric
shock when connecting or disconnecting the speaker cables, disconnect the power cord
before touching any uninsulated parts.
• Make sure that all the bare speaker wire is twisted together and inserted fully into the
speaker terminal. If any of the bare speaker wire touches the back panel it may cause the
power to cut off as a safety measure.
Surround right
12
CENTER
Surround left
SURROUND
R L
2
Connecting your equipment
Switching the speaker terminal
Each press of the speaker button will switch the speaker used
for playback: SP, SPA.
Press repeatedly to choose a speaker terminal option:
• SPA – Sound is output from the speakers connected to
the A-speaker terminals (multichannel playback is
possible).
• SP – No sound is output from the speakers.
Making cable connections
Make sure not to bend the cables over the top of this unit (as
shown in the illustration). If this happens, the magnetic field
produced by the transformers in this unit may cause a
humming noise from the speakers.
Important
• Before making or changing connections, switch off the
power and disconnect the power cord from the AC outlet.
• Before unplugging the power cord, switch the power into
standby.
HDMI cables
Both video and sound signals can be transmitted
simultaneously with one cable. If connecting the player and
the TV via this receiver, for both connections, use HDMI
cables.
HDM
I
Be careful to connect the terminal in the proper direction.
Note
• Set the HDMI parameter in Setting the Audio options on
page 34 to THRU (THROUGH) and set the input signal in
Selecting the audio input signal on page 23 to HDMI, if you
want to hear HDMI audio output from your TV (no sound
will be heard from this receiver).
• If the video signal does not appear on your TV, try adjusting
the resolution settings on your component or display. Note
that some components (such as video game units) have
resolutions that may not be displayed. In this case, use a
(analog) composite connection.
• When the video signal from the HDMI is 480i, 480p, 576i or
576p, Multi Ch PCM sound and HD sound cannot be
received.
About HDMI
The HDMI connection transfers uncompressed digital video,
as well as almost every kind of digital audio that the
connected component is compatible with, including DVDVideo, DVD-Audio, SACD, Dolby Digital Plus, Dolby TrueHD,
DTS-HD Master Audio (see below for limitations), Video CD/
Super VCD and CD.
This receiver incorporates High-Definition Multimedia
Interface (HDMI®/™) technology.
This receiver supports the functions described below through
HDMI connections.
• Digital transfer of uncompressed video (contents protected
by HDCP (1080p/24, 1080p/60, etc.))
• 3D signal transfer
• Deep Color signal transfer
• x.v.Color signal transfer
• Audio Return Channel
• Input of multi-channel linear PCM digital audio signals
(192 kHz or less) for up to 8 channels
• Input of the following digital audio formats:
– Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio
(Dolby TrueHD, DTS-HD Master Audio), DVD-Audio, CD,
SACD (DSD 2 ch only), Video CD, Super VCD
• Synchronized operation with components using the
Control with HDMI function (see Control with HDMI
function on page 49)
• 4K signal transfer
13
– This may not operate properly, depending on the
connected equipment.
– 4K 24p, 4K 25p and 4K 30p signals are supported
Note
• Use a High Speed HDMI®/™ Cable. If HDMI cable other
than a High Speed HDMI®/™ Cable is used, it may not work
properly.
• When an HDMI cable with a built-in equalizer is connected,
it may not operate properly.
• 3D, Deep Color, x.v.Color, 4K signal transfer and Audio
Return Channel are only possible when connected to a
compatible component.
• HDMI format digital audio transmissions require a longer
time to be recognized. Due to this, interruption in the audio
may occur when switching between audio formats or
beginning playback.
• Turning on/off the device connected to this unit’s HDMI
OUT terminal during playback, or disconnecting/
connecting the HDMI cable during playback, may cause
noise or interrupted audio.
®
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing, LLC in the United States and
other countries.
“x.v.Color” and
Corporation.
are trademarks of Sony
4
7
56
2
Connecting your equipment
Analog audio cables
Video cables
Use stereo RCA phono cables to connect analog audio
components. These cables are typically red and white, and
you should connect the red plugs to R (right) terminals and
white plugs to L (left) terminals.
About video outputs connection
Standard RCA video cables
These cables are the most common type of video connection
and are used to connect to the composite video terminals. The
yellow plugs distinguish them from cables for audio.
R
Red (Right)
This receiver is not loaded with a video converter. When you
use HDMI cables for connecting to the input device, the same
cables should be used for connecting to the TV.
The signals input from the analog (composite) video inputs of
this unit will not be output from the HDMI OUT terminal.
L
VID
AUD
IO
White (Left)
EO
Playback component
Yellow
Digital audio cables
Commercially available coaxial digital audio cables or optical
cables should be used to connect digital components to this
receiver.
Coaxial digital
audio cable
COA
XIA
IN L
IN
IN
HDMI
VIDEO
OUT
MONITOR
OUT
Terminal for connection with
source device
OPT
ICA
IN L
Optical cable
HDMI
Note
• When connecting optical cables, be careful when inserting
the plug not to damage the shutter protecting the optical
socket.
• When storing optical cable, coil loosely. The cable may be
damaged if bent around sharp corners.
• You can also use a standard RCA video cable for coaxial
digital connections.
Terminal for connection
with TV monitor
VIDEO
The OSD will
not appear.
TV
Video signals can be output.
14
4
7
56
2
Connecting a TV and playback components
Connecting your equipment
DVD player
4
HDMI/DVI-compatible components
Blu-ray Disc player
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped component
(Blu-ray Disc player, etc.), you can connect it to this receiver
using a commercially available HDMI cable.
If the TV and playback components support the Control with
HDMI feature, the convenient Control with HDMI functions
can be used (see Control with HDMI function on page 49).
• The following connection/setting is required to listen to the
sound of the TV over this receiver.
- If the TV does not support the HDMI Audio Return
Channel function, connect the receiver and TV with audio
cables (as shown).
- If the TV supports the HDMI Audio Return Channel
function, the sound of the TV can be input to the receiver
via the HDMI terminal, so there is no need to connect an
audio cable. In this case, set ARC at HDMI Setup to ON
(see HDMI Setup on page 49).
- Please refer to the TV’s operation manual for directions
on connections and setup for the TV.
HDMI OUT
HDMI OUT
7
Set-top box
56
Game console
DVD recorder, Blu-ray
Disc recorder
OPTICAL
IN1 (TV)
HDMI
OUT
HDMI IN
Note
• In order to listen to the audio from the TV that is connected
to this receiver using an analog audio cables, set-up for
analog audio input is required (see The Input Assign menu
on page 47).
ANALOG
IN1 (CD)
HDMI IN
R
L
ANALOG AUDIO OUT
OPTICAL
DIGITAL AUDIO OUT
Select one
HDMI/DVI-compatible TV
15
If the TV does not support
the HDMI Audio Return
Channel function, this
connection is required to
listen to the TV sound over
the receiver.
2
Connecting your equipment
Connecting your TV with no HDMI input
This diagram shows connections of a TV (with no HDMI input)
and DVD player (or other playback component) to the receiver.
• With these connections, the picture is not output to the TV
even if the DVD player is connected with an HDMI cable.
Connect the DVD player’s video signals using a composite
cable.
• In order to listening to HD audio with this receiver, connect
an HDMI cable, and use analog video cable for video signal
input.
Depending on the player, it may not be possible to output
video signals to both HDMI and other video output
(composite, etc.) simultaneously, and it may be necessary
to make video output settings. Please refer to the operating
instructions supplied with your player for more information.
DVD player
Select one
VIDEO OUT
ANALOG AUDIO OUT
R
HDMI OUT
L
4
Set-top box
7
Select one
VIDEO OUT
DIGITAL AUDIO OUT
COAXIAL
OPTICAL
DIGITAL AUDIO OUT
COAXIAL
OPTICAL
ANALOG AUDIO OUT
R
L
56
Important
• When the receiver and TV are connected by composite
cable, the OSD function allowing display of the receiver’s
settings, operations, etc., on the TV’s screen cannot be
used. In this case, watch the receiver’s front panel display
while performing the various operations and making
settings.
Note
• In order to listen to the audio from the TV that is connected
to this receiver using a analog audio cables, set-up for
analog audio input is required (see The Input Assign menu
on page 47).
• Only one component can be connected to both the optical
input terminal and coaxial input terminal. If connecting
other devices, please use a different method to connect the
audio.
In order to listen to the audio from the source component
that is connected to this receiver using an optical cable or
a coaxial cable, first, switch to the DVD (DVD player) or
SAT/CBL (set-top box), then use RECEIVER and SIGNAL
SEL to choose the audio signal O1 (OPTICAL1) or C1
(COAXIAL1) (see Selecting the audio input signal on
page 23).
HDMI
DVD IN
OPTICAL
IN1 (TV)
COAXIAL
IN1 (CD)
DVD IN
SAT/CBL IN
ANALOG
IN1 (CD)
MONITOR
OUT
This connection is
required in order to
listen to the sound
of the TV over the
receiver.
R
VIDEO IN
OPTICAL
DIGITAL AUDIO OUT
Select one
TV
16
L
ANALOG AUDIO OUT
2
Connecting your equipment
Connecting optional Bluetooth® ADAPTER
When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100
or AS-BT200) is connected to this unit, a product equipped
with Bluetooth wireless technology (portable cell phone,
digital music player, etc.) can be used to listen to music
wirelessly.
 Connect a Bluetooth ADAPTER to the ADAPTER PORT
terminal on the rear panel.
• For instructions on playing the Bluetooth wireless
technology device, see Pairing the Bluetooth ADAPTER and
Bluetooth wireless technology device on page 28.
Connecting to the network through LAN
interface
By connecting this receiver to the network via the LAN
terminal, you can listen to Internet radio stations. To listen to
Internet radio stations, you must sign a contract with an ISP
(Internet Service Provider) beforehand.
When connected in this way, you can play audio files stored
on the components on the local network, including your
computer.
Internet
Modem
Router
Important
WAN
• Do not move the receiver with the Bluetooth ADAPTER
connected. Doing so could cause damage or faulty contact.
LAN
Computer
1
to LAN port
2
3
LAN cable (sold
separately)
Bluetooth® ADAPTER
Connect the LAN terminal on this receiver to the LAN terminal
on your router (with or without the built-in DHCP server
function) with a straight LAN cable (CAT 5 or higher).
17
Turn on the DHCP server function of your router. In case your
router does not have the built-in DHCP server function, it is
necessary to set up the network manually. For details, see The
Network Setup menu on page 39.
Note
• Refer to the operation manual of the equipment you have as
the connected equipment and connection method may
differ depending on your Internet environment.
• When using a broadband Internet connection, a contract
with an Internet service provider is required. For more
details, contact your nearest Internet service provider.
4
7
56
2
Connecting your equipment
Using external antennas
Connecting antennas
Connect the AM loop antenna and the FM wire antenna as
shown below. To improve reception and sound quality,
connect external antennas (see Using external antennas
below).
fig. a
Connecting an iPod
To improve FM reception
Connect an external FM antenna as shown below.
This receiver has a dedicated iPod/iPhone/iPad terminals that
will allow you to control playback of audio content from your
iPod using the controls of this receiver.
fig. b
7
56
75  coaxial
cable
J-shaped plug
(not supplied)
FM UNBAL
75
2
To improve AM reception
4
4
3
Connect a 5 m to 6 m length of vinyl-coated wire to the AM
antenna terminal without disconnecting the supplied AM
loop antenna.
For the best possible reception, suspend horizontally
outdoors.
USB cable that
comes with the iPod
1
iPod/iPhone/iPad
Outdoor
antenna
Note
• An iPod/iPhone/iPad can be connected to the receiver. For
details on supported models and versions of the respective
products, see Playing an iPod on page 25.
1 Push open the tabs, then insert one wire fully into each
terminal, then release the tabs to secure the AM antenna
wires.
2 Fix the AM loop antenna to the attached stand.
To fix the stand to the antenna, bend in the direction indicated
by the arrow (fig. a) then clip the loop onto the stand (fig. b).
3 Place the AM antenna on a flat surface and in a direction
giving the best reception.
Indoor antenna
(vinyl-coated
wire)
5 m to 6 m
4 Connect the FM wire antenna into the FM antenna
socket.
For best results, extend the FM antenna fully and fix to a wall
or door frame. Don’t drape loosely or leave coiled up.
18
 Switch the receiver into standby, and then use the iPod
cable to connect your iPod to the iPod/iPhone/iPad
terminals on the front panel of this receiver.
• For the cable connection, also refer to the operating
instructions for your iPod.
• When connecting an iPhone to this unit, keep the iPhone
at least 20 cm away from this unit. If the iPhone is kept
closer to this unit and a telephone call is received by the
iPhone, noise may be output from this device.
2
Connecting your equipment
• iPod recharging occurs whenever an iPod is connected to
this unit. (Recharging is enabled only when the unit’s
power is turned on.)
• For instructions on playing the iPod, see Playing an iPod on
page 25.
Use a dedicated cable to enjoy iPod video
If an iPod is connected using a dedicated iPod connection
cable (sold separately), then video from the iPod can also be
enjoyed on a TV that is connected to the receiver.
• The iPod cable is not included with this receiver. The
optional iPod cable from Pioneer is sold separately under
the part number L308102013030-IL. Contact the Pioneer
Customer Support division for more information on
obtaining an optional iPod cable.
• iPhone 5, iPad 4th generation, iPad mini, iPod touch 5th
generation and iPod nano 7th generation cannot be
connected using a separately sold iPod cable.
Note
• Due to linked operation of the HDMI control function, if a
supported TV and receiver are connected using a HDMI
cable and the TV input is changed during iPod input, the
receiver may automatically also change to TV input. If this
happens, please either change the receiver’s input back to
iPod, or turn OFF the HDMI control function (see HDMI
Setup on page 49).
Connecting an MHL-compatible device
An MHL-compatible mobile device can be connected to enjoy
full-HD videos, high quality multi-channel audio, and photos
etc., with charge the battery on the receiver. Use the MHL
cable (sold separately) to connect the device.
It is possible to play audio and photo files by connecting USB
devices to this receiver.
 Switch the receiver into standby then connect your USB
device to the iPod/iPhone/iPad terminals on the front panel
of this receiver.
• This receiver does not support a USB hub.
• For instructions on playing the USB device, see Playing a
USB device on page 26.
MHL cable (sold
separately)
 Switch the receiver into standby then use the MHL cable
(sold separately) to connect your MHL enabled device to the
MHL terminal on the front panel of this receiver.
• The MHL-compatible device is recharged whenever it is
connected to this unit. (Recharging is enabled only when
the unit’s power is turned on.)
• For instructions on playing the MHL-compatible device, see
Playing an MHL-compatible device on page 27.
USB mass
storage device
iPod/iPhone/iPad
19
7
56
Connecting a USB device
MHL-compatible
device
iPod cable
4
2
Connecting your equipment
Connecting an HDMI-equipped component to
the front panel input
Plugging in the receiver
Only plug in after you have connected all your components to
this receiver, including the speakers.
1 Plug the supplied power cord into the AC IN socket on
the back of the receiver.
2 Plug the other end into a power outlet.
CAUTION
Video camera (etc.)
• Handle the power cord by the plug. Do not pull out the plug
by tugging the cord and never touch the power cord when
your hands are wet as this could cause a short circuit or
electric shock. Do not place the unit, a piece of furniture,
etc., on the power cord, or pinch the cord. Never make a
knot in the cord or tie it with other cords. The power cords
should be routed such that they are not likely to be stepped
on. A damaged power cord can cause a fire or give you an
electrical shock. Check the power cord once in a while.
When you find it damaged, ask your nearest PIONEER
authorized service center or your dealer for a replacement.
• The receiver should be disconnected by removing the
mains plug from the wall socket when not in regular use,
e.g., when on vacation.
Note
• After this receiver is connected to an AC outlet, a 2 second
to 10 second HDMI initialization process begins. You
cannot carry out any operations during this process. The
HDMI indicator in the front panel display blinks during this
process, and you can turn on this receiver once it has
stopped blinking. When you set the Control with HDMI to
OFF, you can skip this process. For details about the
Control with HDMI feature, see HDMI Setup on page 49.
20
4
7
56
Chapter
Basic Setup
Before setting up
This receiver allows you to adjust the system setup, using the
on-screen display (OSD) that is shown on the TV screen.
• The OSD will not appear if you have connected using the
HDMI output to your TV. Use composite connections for
system setup.
First, follow the procedure below to make sure that the OSD
screen is displayed.
1
the TV input to the input that connects this
2 Switch
receiver to the TV through the corresponding
Switch on the receiver and your TV.
composite video cable.
For example, if you connected this receiver to the VIDEO
jacks on your TV, make sure that the VIDEO input is now
selected.
on the remote control, then press the
3 Press
HOME MENU button.
RECEIVER
The Home Menu of the OSD screen will be displayed on
the TV. If nothing appears on the screen, try to change the
TV format setting on the receiver (see below).
have set up the microphone provided with your system, the
receiver uses the information from a series of test tones to
optimize the speaker settings and equalization for your
particular room.
AUDIO
PARAMETER
SOURCE
ENTER
HOME
MENU
PTY
iPod CTRL
TUNE
PRESET
RECEIVER SLEEP
TOOLS
MENU
TUNE
TOP
MENU
INPUT
BAND
RETURN
MUTE
1 Switch on the receiver and your TV.
the TV input to the input that connects this
2 Switch
receiver to the TV through the corresponding HDMI
cable.
the microphone to the MCACC SETUP MIC jack
3 Connect
on the front panel.
Make sure there are no obstacles between the speakers
and the microphone.
21
Microphone
Tripod
If you have a tripod, use it to place the microphone so that
it’s about ear level at your normal listening position.
Otherwise, place the microphone at ear level using a
table or a chair.
BD button on the remote control to switch to BD
4 Press
entry.
on the remote control, then press the
5 Press
HOME MENU button.
RECEIVER
RECEIVER
The display shows the new setting (PAL or NTSC).
The Auto Multi-Channel ACoustic Calibration (MCACC) setup
measures the acoustic characteristics of your listening area,
taking into account ambient noise, speaker size and distance,
and tests for both channel delay and channel level. After you
56
Important
• The OSD will not appear if you have connected using the
composite output to your TV. Use HDMI connection for
Auto MCACC setup.
• The Auto MCACC setup will overwrite any existing speaker
settings you’ve made.
• Before using the Auto MCACC setup, the NETRADIO,
M.SERVER, FAVORITE, iPod/USB or ADAPTER input
should not be selected as an input source.
• VSX-828 only: When both the surround back speaker and
the front height speaker are connected, conduct Auto
MCACC setup twice: once with the Speaker System setting
is in Surr.Back and once with the Speaker System setting
is in Height. (There is no need to conduct Auto MCACC
setup every time the Speaker System setting is changed.)
If the OSD screen is not displayed correctly, it may be that the
TV system is set incorrectly for your country or region.
Automatically setting up for surround sound
(MCACC)
7
CAUTION
Changing the TV format setting
1 Switch the receiver into standby.
holding down the TUNE  button, press and hold
2 While
the STANDBY/ON button for about two seconds.
4
• The test tones used in the Auto MCACC setup are output at
high volume.
PRESET
3
The Home Menu appears on your TV. Use /// and
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
• Press HOME MENU at any time to exit the Home
Menu. If you cancel the Auto MCACC setup at any
time, the receiver automatically exits and no settings
will be made.
• The screensaver automatically starts after three
minutes of inactivity.
3
Basic Setup
‘Auto MCACC’ from the Home Menu, then press
the speaker configuration.
6 Select
9 Confirm
ENTER.
The configuration shown on-screen should reflect the
actual speakers you have.
Home Menu
1 . Auto M C AC C
2 . Manua l S P S e tu p
3 . Input A s s ig n
4. Auto Pow e r D ow n
5. HDMI S e tu p
6. Netwo rk S ta n d by
7. MHL S e tu p
8. OSD S e tu p
• Mic In! blinks when the microphone is not connected
to MCACC SETUP MIC jack.
Try to be as quiet as possible after pressing ENTER. The
system outputs a series of test tones to establish the
ambient noise level.
the instructions on-screen.
7 Follow
• Make sure the microphone is connected.
• Make sure the subwoofer is on and the volume is
turned up.
• When using surround back or front height speakers,
turn on the power to the amplifier to which the
surround back or front height speakers are connected,
and adjust the sound level to the desired level (VSX-828
only).
• See below for notes regarding background noise and
other possible interference.
for the test tones to finish.
8 Wait
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
1 . Auto MCACC
Check
Front
Center
Surr
Subwoofer
[
[
[
[
YES
YES
YES
YES
]
]
]
]
OK
Return
10:Next
• With error messages (such as Too much ambient
noise) select RETRY after checking for ambient noise
(see Other problems when using the Auto MCACC
setup below).
If the speaker configuration displayed isn’t correct, use
/ to select the speaker and / to change the
setting. When you’re finished, go to the next step.
If you see an error message (ERR) in the right side
column, there may be a problem with the speaker
connection. If selecting RETRY doesn’t fix the problem,
turn off the power and check the speaker connections.
sure ‘OK’ is selected, then press ENTER.
10 Make
If the screen in step 9 is left untouched for 10 seconds
and ENTER is not pressed in step 10, the Auto MCACC
setup will start automatically as shown.
1 . Auto MCACC
Now Analyzing
Surround Analyzing
Speaker System
X.Over
Speaker Distance
Channel Level
Acoustic Cal EQ
1 . Au t o MCACC
Return
N ow Analyzing
E nv iro n ment Check
A mb ie nt Noise
S p e a k er YES/NO
Ret urn
• For correct speaker settings, do not adjust the volume
during the test tones.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, X.Over, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 1 to 3 minutes.
22
Auto MCACC setup has finished! You return to the
11 The
4
Home Menu.
The settings made in the Auto MCACC setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
Home Menu (starting on page 45).
Note
• Depending on the characteristics of your room, sometimes
identical speakers with cone sizes of around 12 cm will end
up with different size settings. You can correct the setting
manually using the Speaker Setting on page 45.
• The subwoofer distance setting may be farther than the
actual distance from the listening position. This setting
should be accurate (taking delay and room characteristics
into account) and generally does not need to be changed.
Other problems when using the Auto MCACC
setup
If the room environment is not optimal for the Auto MCACC
setup (too much background noise, echo off the walls,
obstacles blocking the speakers from the microphone) the
final settings may be incorrect. Check for household
appliances (air conditioner, fridge, fan, etc.), that may be
affecting the environment and switch them off if necessary. If
there are any instructions showing in the front panel display,
please follow them.
• Some older TVs may interfere with the operation of the
microphone. If this seems to be happening, switch off the
TV when doing the Auto MCACC setup.
7
56
Chapter
4
Basic playback
Playing a source
Here are the basic instructions for playing a source (such as
a DVD disc) with your home theater system.
RECEIVER SLEEP
SOURCE
AUDIO
PARAMETER
RECEIVER
HOME
MENU
PTY
iPod CTRL
ENTER
TUNE
PRESET
PRESET
INPUT
TOOLS
MENU
TUNE
TOP
MENU
BAND
RETURN
MUTE
on your system components and receiver.
1 Switch
Start by switching on the playback component (for
example a DVD player), your TV and subwoofer (if you
have one), then the receiver (press RECEIVER).
• Make sure the setup microphone is disconnected.
the TV input to the input that connects this
2 Switch
receiver.
For example, if you connected this receiver to the VIDEO
jacks on your TV, make sure that the VIDEO input is now
selected.
input function buttons to select the input function
3 Press
you want to play.
• The input of the receiver will switch over, and you will
be able to operate other components using the remote
control. To operate the receiver, first press RECEIVER
on the remote control, then press the appropriate
button to operate.
• The input source can also be selected by using INPUT
SELECT
buttons on the remote control, or by
using the front panel INPUT SELECTOR dial. In this
case, the remote control won’t switch operational
modes.
If you selected the proper input source and there is still
no sound, select the audio input signal for playback (see
Selecting the audio input signal below).
Press AUTO/DIRECT to select ‘AUTO SURROUND’ and
4 start
playback of the source.
If you’re playing a Dolby Digital or DTS surround sound
DVD disc, with a digital audio connection, you should
hear surround sound. If you’re playing a stereo source or
if the connection is an analog audio connection, you will
only hear sound from the front left/right speakers in the
default listening mode.
It is possible to check on the front panel display whether
or not surround sound playback is being performed
properly.
When using a surround back speaker and 2D+PLII are
displayed when playing Dolby Digital 5.1-channel signals,
and DTS+NEO:6 is displayed when playing DTS 5.1channel signals.
When not using a surround back speaker, 2D is
displayed when playing Dolby Digital signals.
If the display does not correspond to the input signal and
listening mode, check the connections and settings.
Note
• You may need to check the digital audio output settings on
your DVD player or digital satellite receiver. It should be set
to output Dolby Digital, DTS and 88.2 kHz/96 kHz PCM (2
channel) audio, and if there is an MPEG audio option, set
this to convert the MPEG audio to PCM.
• Depending on your DVD player or source discs, you may
only get digital 2 channel stereo and analog sound. In this
case, the receiver must be set to a multichannel listening
mode if you want multichannel surround sound.
VOLUME +/– to adjust the volume level.
5 Use
Turn down the volume of your TV so that all sound is
coming from the speakers connected to this receiver.
23
Selecting the audio input signal
The audio input signal can be selected for each input source.
Once it is set, the audio input that was selected will be applied
whenever you select the input source using the input function
buttons.
RECEIVER SLEEP
SOURCE
RECEIVER
1
2
3
DISP
4
5
6
CH
7
8
9
CH
CLR
0
ENTER
SHIFT
INPUT
, then press SIGNAL SEL to select the
 Press
audio input signal corresponding to the source
RECEIVER
component.
Each press cycles through the following:
• H – Selects an HDMI signal. H can be selected for BD,
DVD, SAT/CBL, DVR/BDR, HDMI/MHL or GAME
input. For other inputs, H cannot be selected.
- When the HDMI option in Setting the Audio options
on page 34 is set to THRU, the sound will be heard
through your TV, not from this receiver.
• A – Selects the analog inputs.
• C1/O1 – Selects the digital input. The coaxial 1 input is
selected for C1, and the optical 1 audio input is
selected for O1.
When H (HDMI) or C1/O1 (digital) is selected and the
selected audio input is not provided, A (analog) is
automatically selected.
Note
• BD, DVR/BDR, HDMI/MHL and GAME inputs are fixed to
H (HDMI). It cannot be changed.
• For the TV input, only A (analog) or C1/O1 (digital) can be
selected. However, if the ARC at HDMI Setup is set to ON,
the input is fixed to H (HDMI) and cannot be changed.
• When set to H (HDMI) or C1/O1 (digital), 2 lights when a
Dolby Digital signal is input, and DTS lights when a DTS
signal is input.
• When the H (HDMI) is selected, the A and DIGITAL
indicators are off (see page 8).
4
7
56
4
• When digital input (optical or coaxial) is selected, this
receiver can only play back Dolby Digital, PCM (32 kHz to
96 kHz) and DTS (including DTS 96 kHz/24 bit) digital signal
formats. The compatible signals via the HDMI terminals
are: Dolby Digital, DTS, SACD (DSD 2 ch only), PCM
(32 kHz to 192 kHz sampling frequencies), Dolby TrueHD,
Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio
and DVD Audio (including 192 kHz). With other digital
signal formats, set to A (analog).
• You may get digital noise when a LD or CD player
compatible with DTS is playing an analog signal. To prevent
noise, make the proper digital connections (page 14) and
set the signal input to C1/O1 (digital).
• Some DVD players don’t output DTS signals. For more
details, refer to the instruction manual supplied with your
DVD player.
Basic playback
Tip
• In order to enjoy the picture and/or sound from devices connected to each terminal, select the input by doing the following.
7
Audio
DVD SAT/CBL CD
4
TV
Video/Audio (HDMI)
DVD
SAT/CBL
BD
GAME DVR/BDR
NETWORK
RECEIVER
SIGNAL SEL
3
Video
ADAPTER
Audio
SAT/CBL DVD
56
C1
Audio
DVD SAT/CBL RECEIVER
SIGNAL SEL
3
A
A
1.
2.
TV
(TV input)
Other than TV input
RECEIVER
SIGNAL SEL
3
O1
TUNER
Audio
CD
TV
RECEIVER
SIGNAL SEL
3
24
A
ANALOG IN1 audio input terminal is
assigned to CD under factory settings. If
you want to change this to TV input,
please change the settings in the Input
Assign menu (page 47).
4
Basic playback
This receiver has the iPod iPhone iPad USB terminal that will
allow you to control playback of audio content from your iPod
using the controls of this receiver.
Important
on the receiver and your TV.
1 Switch
See Connecting an iPod on page 18.
the TV input so that it connects to the receiver.
2 Switch
• Switch the TV input to the input that connects this
receiver to the TV through the corresponding HDMI
cable.
When the display shows the names of folders and files,
you’re ready to play music from the iPod.
• If after pressing iPod/USB the display shows NO
DEVICE, try switching off the receiver and
reconnecting the iPod to the receiver.
• The controls of your iPod will be inoperable when
connected to this receiver.
Playing back files stored on an iPod
To navigate songs on your iPod, you can take advantage of the
OSD of your TV connected to this receiver.
• Note that non-roman characters in the title are displayed as
‘#’.
• This feature is not available for photos or video clips on your
iPod.
Finding what you want to play
When your iPod is connected to this receiver, you can browse
songs stored on your iPod by playlist, artist, album name,
song name, genre or composer, similar to using your iPod
directly.
/ to select a category, then press ENTER to
1 Use
browse that category.
• When  or  is pressed at the list screen, the
page switches.
• To return to the previous level any time, press RETURN.
Use / to browse the selected category (e.g.,
2 albums).
• Use / to move to previous/next levels.
Basic playback controls
This receiver’s remote control buttons can be used for basic
playback of files stored on an iPod.
• Press iPod/USB to switch the remote control to the iPod/
USB operation mode.
AUDIO
PARAMETER
Tip
25
7
56
TOOLS
MENU
TUNE
TOP
MENU
HOME
MENU
PTY
iPod CTRL
ENTER
TUNE
BAND
RETURN
1
2
3
DISP
4
5
6
CH
7
8
9
CH
SHIFT
Watching photos and video content
To view photos or video on your iPod, since video control is not
possible using this receiver, you must use the main controls
of your iPod instead.
Important
- In order to display the images or video on the iPod on the
receiver, an iPod cable sold separately is required.
- To play photos or video on your iPod, you must connect
the composite MONITOR OUT jack and TV. The photos
and video content will not appear if you have connected
using the HDMI output to your TV.
• iPod photos and video content can be viewed only when the
iPod is connected to the iPod VIDEO input on the front panel.
• When making the connection, please use a dedicated iPod
cable (sold separately).
• This feature can only be used with an iPod having video output.
browsing until you arrive at what you want to
3 Continue
Press iPod CTRL to switch to the iPod controls for photo
play, then press  to start playback.
1 and
video playback.
• If you’re in the song category, you can also press ENTER to
start playback.
• You can play all of the songs in a particular category by
selecting the All item at the top of each category list. For
example, you can play all the songs by a particular artist.
4
MUTE
PRESET
• Pioneer cannot under any circumstances accept
responsibility for any direct or indirect loss arising from any
inconvenience or loss of recorded material resulting from
the iPod failure.
• About one minute is required between turning the power
on and completion of startup.
• USB works with iPhone 5, iPhone 4S, iPhone 4, iPhone
3GS, iPhone 3G, iPhone, iPad (3rd and 4th generation),
iPad 2, iPad, iPad mini, iPod touch (1st through 5th
generation) and iPod nano (3rd through 7th generation).
Audio only for iPhone 5, iPad 4th generation, iPad mini,
iPod touch 5th generation and iPod nano (6th and 7th
generation). However, some of the functions may be
restricted for some models.
• This receiver has been developed and tested for the
software version of iPod/iPhone/iPad indicated on the
website of Pioneer (http://pioneer.jp/homeav/support/ios/
ao/).
• Installing software versions other than indicated on the
website of Pioneer to your iPod/iPhone/iPad may result in
incompatibility with this receiver.
• iPod, iPhone and iPad are licensed for reproduction of noncopyrighted materials or materials the user is legally
permitted to reproduce.
• Features such as the equalizer cannot be controlled using
this receiver, and we recommend switching the equalizer
off before connecting.
• Make sure the receiver is in standby when disconnecting
the iPod/iPhone/iPad.
Press iPod/USB to switch the receiver to the iPod/USB
3 input.
PRESET
Playing an iPod
The receiver controls will be unavailable while you are
watching iPod videos or browsing photos.
Tip
• Change the receiver’s input to the iPod in one action by
pressing iPod iPhone iPad DIRECT CONTROL on the front
panel to enable iPod operations on the iPod.
4
Basic playback
receiver to the TV through the corresponding HDMI
cable.
Tip
Press iPod/USB on the remote control to switch the
3 receiver
to the iPod/USB input.
When the display shows the names of folders and files,
you’re ready to play from the USB device.
If a USB Error message lights in the display, try following
the points below:
• Switch the receiver off, then on again.
• Reconnect the USB device with the receiver switched
off.
• Select another input source (like BD), then switch back
to iPod/USB.
• Use a dedicated AC adapter (supplied with the device)
for USB power.
If this doesn’t remedy the problem, it is likely your USB
device is incompatible.
Playing a USB device
It is possible to play files using the USB interface on the front
of this receiver.
Important
• Pioneer cannot guarantee compatibility (operation and/or
bus power) with all USB mass storage devices and
assumes no responsibility for any loss of data that may
occur when connected to this receiver.
• About one minute is required between turning the power
on and completion of startup.
•
•
•
•
•
•
1
Switch on the receiver and your TV.
See Connecting a USB device on page 19.
Playing back audio files stored on a USB memory
device
The maximum number of levels that you can select in Step 1
(below) is 9.
• Note that non-Roman characters in the playlist are
displayed as ‘#’.
TUNE
TOP
MENU
HOME
MENU
PTY
iPod CTRL
ENTER
TUNE
BAND
RETURN
1
2
3
DISP
4
5
6
CH
7
8
9
CH
SHIFT
Playing back photo files stored on a USB memory
device
/ to select a folder, then press ENTER to browse
1 Use
that folder.
• For high resolution files, some time may be required
for the photo to appear.
• To return to the previous level any time, press RETURN.
browsing until you arrive at what you want to
2 Continue
play, then press  to start playback.
The selected content is displayed in full screen and a
slideshow starts.
Basic playback controls
TOP
MENU
/ to select a folder, then press ENTER to browse
1 Use
that folder.
• To return to the previous level any time, press RETURN.
2
TOOLS
MENU
ENTER
HOME
MENU
PTY
iPod CTRL
TUNE
PRESET
•
Note
Compatible USB devices include external magnetic hard
drives, portable flash memory (particularly keydrives) and
digital audio players (MP3 players) of format FAT16/32.
Copyrighted audio files cannot be played back on this
receiver.
With large amounts of data, it may take longer for the
receiver to read the contents of a USB device.
If the file selected cannot be played back, this receiver
automatically skips to the next file playable.
When the file currently being played back has no title
assigned to it, the file name is displayed in the OSD instead;
when neither the album name nor the artist name is
present, the row is displayed as a blank space.
Note that non-roman characters in the playlist are
displayed as ‘#’.
Make sure the receiver is in standby when disconnecting
the USB device.
AUDIO
PARAMETER
PRESET
• Change the receiver’s input to the iPod in one action by
pressing iPod iPhone iPad DIRECT CONTROL on the
front panel to enable iPod operations on the iPod.
MUTE
PRESET
the TV input so that it connects to the receiver.
2 Switch
• Switch the TV input to the input that connects this
PRESET
iPod CTRL again to switch back to the receiver
2 Press
controls when you’re done.
BAND
RETURN
MUTE
Continue browsing until you arrive at what you want to
play, then press  to start playback.
Basic playback controls
This receiver’s remote control buttons can be used for basic
playback of files stored on USB devices.
• Press iPod/USB to switch the remote control to the iPod/
USB operation mode.
26
ENTER,  – Starts displaying a photo and playing a slideshow.
 – Stops the player and returns to the previous menu.
Tip
• Slideshows of photo files can be played while listening to
music files by returning to the folder/file list display while
playing a music file on a USB device then playing the photo
files.
4
7
56
4
Basic playback
About playable file formats
FLAC
The USB function of this receiver supports the following file
formats. Note that some file formats are not available for
playback although they are listed as playable file formats.
With WAV, FLAC, AIFF and Apple Lossless files, when music
files with the same format, sampling frequency, quantization
bit number and number of channels are played successively,
they are played with no gap.
.flacc
Extension
Stream
Quantization bitrate
16 bit, 24 bit
Channel
16 bit
Apple Lossless
Channel
2 ch
.m4a
.mp4
Supported/Supported
WAV (LPCM)
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bitrate
16 bit, 24 bit
Channel
2 ch
WMA (WMA2/7/8/9)
16 bit
Extension
2 ch
JPEG
VBR/CBR
Supported/Supported
AAC (MPEG-4 AAC LC, MPEG-4 HE AAC (aacPlus v1/2))
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz
Quantization bitrate
16 bit
Channel
Bitrate
VBR/CBR
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz
Quantization bitrate
16 bit, 24 bit
2 ch
Photo files
Quantization bitrate
5 kbps to 320 kbps
Sampling frequency
a. MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.
b. Files encoded using Windows Media Codec 9 may be playable
but some parts of the specification are not supported;
specifically, Pro, Lossless, Voice.
c. Uncompressed FLAC files are not supported. Pioneer does not
guarantee playback.
32 kHz, 44.1 kHz, 48 kHz
Bitrate
2 ch
Channel
Sampling frequency
Channel
.m4a
.aac
.3gp
.3g2
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz
Quantization bitrate
8 kbps to 320 kbps
2 ch
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz
VBR/CBR
.wmab
16 bit, 24 bit
Sampling frequency
Bitrate
.wav
Quantization bitrate
AIFF
MP3 (MPEG-1 Audio Layer 3)
.mp3a
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Channel
.aif
.aiff
Music files
Sampling frequency
.jpg
Format
Meeting the following conditions:
• Baseline JPEG format
• Y:Cb:Cr – 4:2:2
2 ch
16 kbps to 320 kbps
Supported/Supported
27
Playing an MHL-compatible device
MHL (Mobile High-definition Link) is an interface standard for
transmitting digital signals with mobile devices. MHL can
carry high quality multi-channel audio data and full-HD video
formats.
The MHL-compatible device’s video signals are output from
the TV connected to the receiver, the audio signals are output
from the speakers connected to the receiver or TV.
Press RECEIVER to switch on the receiver and your
1 TV.
See Connecting an MHL-compatible device on page 19.
HDMI/MHL on the remote control to switch the
2 Press
receiver to the MHL.
and play the desired contents on the MHL3 Select
compatible device.
Note
• MHL-compatible devices can be operated with the
receiver’s remote control by pressing the remote control’s
HDMI/MHL button, but depending on the MHL-compatible
device being used, some buttons may not be operable.
• To playback from a MHL-compatible device connected to
the receiver on a TV that is also connected to the receiver,
the power to the receiver must be turned on.
4
7
56
4
Basic playback
Bluetooth® ADAPTER for Wireless Enjoyment of
Music
Bluetooth wireless technology enabled device:
cell phone
Bluetooth wireless technology enabled device:
Digital music player
Device not equipped with Bluetooth wireless
technology: Digital music player + Bluetooth
audio transmitter (sold commercially)
Music data
This receiver
Bluetooth®
ADAPTER
Remote control
operation
Wireless music play
When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100
or AS-BT200) is connected to this unit, a product equipped
with Bluetooth wireless technology (portable cell phone,
digital music player, etc.) can be used to listen to music
wirelessly. Also, by using a commercially available transmitter
supporting Bluetooth wireless technology, you can listen to
music on a device not equipped with Bluetooth wireless
technology. The AS-BT100 and AS-BT200 model supports
SCMS-T contents protection, so music can also be enjoyed on
devices equipped with SCMS-T type Bluetooth wireless
technology.
• With the AS-BT100, some functions may not be available on
this receiver.
• It must be necessary that the Bluetooth wireless technology
enabled device supports A2DP profiles.
Important
• Pioneer does not guarantee proper connection and
operation of this unit with all Bluetooth wireless technology
enabled devices.
• About one minute is required between turning the power
on and completion of startup.
Remote control operation
The remote control supplied with this unit allows you to play
and stop media, and perform other operations.
• It must be necessary that the Bluetooth wireless technology
enabled device supports AVRCP profiles.
• Remote control operations cannot be guaranteed for all
Bluetooth wireless technology enabled devices.
Pairing the Bluetooth ADAPTER and Bluetooth
wireless technology device
“Pairing” must be done before you start playback of Bluetooth
wireless technology content using Bluetooth ADAPTER. Make
sure to perform pairing first time you operate the system or
any time pairing data is cleared. “Pairing” is the step
necessary to register Bluetooth wireless technology device to
enable Bluetooth communications. For more details, see also
the operating instructions of your Bluetooth wireless
technology device.
• Pairing is required when you first use Bluetooth wireless
technology device and Bluetooth ADAPTER.
• To enable Bluetooth communication, pairing should be
done with both of your system and Bluetooth wireless
technology device.
• If the Bluetooth wireless technology device’s security code
is “0000”, there is no need to make the security code setting
on the receiver. Press ADAPTER to switch the ADAPTER
input, then conduct the pairing operation on the Bluetooth
wireless technology device. If pairing is successful, there is
no need to performing the pairing operation below.
28
• When using the AS-BT200 only: This unit complies with
Bluetooth Specifications Ver. 2.1. When this unit and
another device equipped with Bluetooth wireless
technology both comply with Bluetooth Specification Ver.
2.1, pairing of the two may be possible without the need for
inputting a password.
In this case, a passcode may be displayed on this receiver
and on the device equipped with Bluetooth wireless
technology. If this happens, check that the same passcode
is displayed on this receiver and the device equipped with
Bluetooth wireless technology, then press ENTER. After
this, also perform the connection operation on the
Bluetooth device to be connected. If the passcode does not
match the code displayed on the Bluetooth device to be
connected, press RETURN to cancel pairing, then try
starting over.
Press ADAPTER to set the ADAPTER input, then conduct
the pairing operation on the Bluetooth wireless technology
device. If pairing is successful, there is no need to
performing the pairing operation below.
• Pair one unit at a time.
• When connecting this receiver by Bluetooth connections
with a device equipped with the Bluetooth function to listen
to music, do not connect any devices other than this
receiver by Bluetooth connection to the Bluetooth-equipped
device. If a Bluetooth connection is already established with
a device other than this receiver, disconnect the other
device before connecting this receiver.
Press ADAPTER to switch the receiver to ADAPTER
1 input.
2 Press TOP MENU to select Bluetooth Setup.
3 Use / to select PIN, then press ENTER.
Use / to select one of PIN codes 0000, 1234 or 8888,
4 then
press ENTER.
You can use any of 0000/1234/8888 PIN codes.
Bluetooth wireless technology device using any other PIN
code cannot be used with this system.
4
7
56
4
Basic playback
and set it into the pairing mode.
to see that the Bluetooth ADAPTER is detected by
6 Check
the Bluetooth wireless technology device.
When Bluetooth wireless technology device is connected:
Bluetooth wireless technology device name appears in
the receiver display.
• The system can display alphanumeric characters only.
Other characters may not be displayed correctly.
When Bluetooth wireless technology device is not
connected:
WAITING appears in the receiver display. In this case,
perform the connection operation from the side of the
Bluetooth wireless technology device.
From the Bluetooth wireless technology device list,
7 select
Bluetooth ADAPTER and enter the PIN code
selected in the step 4.
• PIN code may in some case be referred to as
PASSKEY.
1
Press ADAPTER to switch the receiver to ADAPTER
input.
The ADAPTER input can also be selected by pressing
SOUND RETRIEVER AIR on the front panel. In this case,
S.R AIR, the optimum listening mode, is selected
automatically.
the connection operation from the side of the
2 Perform
Bluetooth wireless technology device to the Bluetooth
ADAPTER.
• When the Bluetooth ADAPTER is not plugged into the
ADAPTER PORT terminal, NO ADP will be displayed if
ADAPTER input is selected.
Start playback of music contents stored in Bluetooth
3 wireless
technology device.
iPod CTRL
RETURN
MUTE
listening to a source, press
4 While
ADV SURR repeatedly to select S.R AIR.
Note
• Bluetooth technology works with iPhone 5, iPhone 4S,
iPhone 4, iPhone 3GS, iPhone 3G, iPhone, iPad (3rd and 4th
generation), iPad 2, iPad, iPad mini, and iPod touch (2nd
through 5th generation).
• The Air Jam function cannot be used while an iPod is
connected to this receiver.
• With this receiver, when an iPod is connected or
disconnected while the music of a Bluetooth wireless
technology device is playing, the connection with the
Bluetooth wireless technology device may be canceled.
RECEIVER then press
AIR JAM
Air Jam – a Pioneer-exclusive application and available for
free.
Air Jam lets you connect multi compatible devices to this unit
using Bluetooth wireless technology. With it, you can make a
group playlist directly on a supported device to play in your
home theater through the unit. You and your friends can add
songs from your devices to the playlist. Also Air Jam lets you
delete the song before anyone has to hear it.
Press ADAPTER to switch the receiver to ADAPTER
1 input.
2 Press TOP MENU to select Bluetooth Setup.
3 Use / to select ‘Air Jam’, then press ENTER.
4 Use / to select ‘Air Jam ON’, then press ENTER.
For more details on using Air Jam, access our website.
http://pioneer.jp/support/soft/iapp_airjam/en.html
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by PIONEER CORPORATION is under license. Other
trademarks and trade names are those of their respective
owners.
This receiver’s remote control buttons can be used for
basic playback of files stored on the Bluetooth wireless
technology device.
29
Listening to the radio
The following steps show you how to tune in to FM and AM
radio broadcasts using the automatic (search) and manual
(step) tuning functions. Once you are tuned to a station you
can memorize the frequency for recall later—see Saving
station presets below for more on how to do this.
AUDIO
PARAMETER
TOOLS
MENU
TUNE
TOP
MENU
ENTER
HOME
MENU
PTY
iPod CTRL
T U NE
PRESET
Listening to Music Contents of Bluetooth wireless
technology device with Your System
• Bluetooth wireless technology device should be
compatible with AVRCP profile.
• Depending on Bluetooth wireless technology device
you use, operation may differ from what is shown in
the remote control buttons.
PRESET
on the Bluetooth wireless technology device
5 Switch
that you want to make pairing, place it near the system
BAND
RETURN
MUTE
1 Press TUNER to select the tuner.
BAND to change the band (FM or AM), if necessary.
2 Use
Each press switches the band between FM (stereo or
mono) and AM.
to a station.
3 Tune
There are three ways to do this:
 Automatic tuning
To search for stations in the currently selected band,
press and hold TUNE / for about a second. The
receiver will start searching for the next station, stopping
when it has found one. Repeat to search for other
stations.
4
7
56
4
Basic playback
 Manual tuning
To change the frequency one step at a time, press
TUNE /.
 High speed tuning
Press and hold TUNE / for high speed tuning.
If the TUNE or ST indicators don’t light when tuning to an FM
station because the signal is weak, set the receiver to the
mono reception mode.
BAND to select FM MONO.
 Press
This should improve the sound quality and allow you to
enjoy the broadcast.
ENTER.
4 Press
The preset number stop blinking and the receiver stores
Note
• If the receiver is left disconnected from the AC power outlet
for over a month, the station memories will be lost and will
have to be reprogrammed.
• Stations are stored in stereo. When the station is stored in
the FM MONO mode, it shows as ST when recalled.
Listening to station presets
Saving station presets
If you often listen to a particular radio station, it’s convenient
to have the receiver store the frequency for easy recall
whenever you want to listen to that station. This saves the
effort of manually tuning in each time. This unit can memorize
up to 30 stations.
AUDIO
PARAMETER
TOOLS
MENU
You will need to have some presets stored to do this. See
Saving station presets above if you haven’t done this already.
Press PRESET / to select the station preset you
 want.
• You can also use the number buttons on the remote
control to recall the station preset.
TUNE
TOP
MENU
Naming preset stations
ENTER
HOME
MENU
PTY
iPod CTRL
TUNE
For easier identification, you can name all of your preset
stations.
PRESET
PRESET
SOURCE
RECEIVER
You can also use the number buttons.
the station.
Improving FM sound
RECEIVER SLEEP
Press PRESET / to select the station preset you
3 want.
INPUT
BAND
RETURN
MUTE
the station preset you want to name.
1 Choose
See Listening to station presets above for how to do this.
TOOLS twice.
2 Press
The cursor at the first character position is blinking on
the display.
1
2
3
DISP
to a station you want to memorize.
1 Tune
See Listening to the radio above for more on this.
TOOLS.
2 Press
The display shows PRESET, then a blinking MEM and
station preset.
the name you want.
3 Input
Choose a name up to eight characters long.
• Use PRESET / to select character position.
• Use TUNE / to select characters.
• The name is stored when ENTER is pressed.
Tip
• To erase a station name, follow steps 1 and 2, and press
ENTER while the display is blank. Press TOOLS while the
display is blank, to keep the previous name.
30
• Once you have named a station preset, Press DISP to show
the name. When you want to return to the frequency
display, press DISP several times to show the frequency.
Changing the radio frequency step
If you find that you can’t tune into stations successfully, the
frequency step may not be suitable for your country/region.
Here’s how to switch the setting:
1 Switch the receiver into standby.
holding down TUNE  button, press and hold
2 While
STANDBY/ON button for about two seconds.
The channel tuning step alternates between 10K STEP
and 9K STEP each time you do this.
4
7
56
Chapter
5
Listening to your system
Choosing the listening mode
This receiver offers a variety of listening modes to
accommodate playback of various audio formats. Choose one
according to your speaker environment or the source.

While listening to a source, press the listening mode
button repeatedly to select a listening mode you want.
Note
• Stereo surround (matrix) formats are decoded accordingly
using NEO:6 CINEMA or DOLBY PLIIx MUSIC (VSX-828
only) (see Listening in surround sound below for more on
these decoding formats).
• When listening to the ADAPTER input, the S.R AIR feature
is selected automatically (see Using the Advanced surround
on page 32 for more on this).
Type of surround modes
Two channel sources
AUDIO
PARAMETER
TOOLS
MENU
TUNE
• The listening mode is shown on the display on the front
panel.
Important
• The listening modes and many features described in this
section may not be available depending on the current
source, settings and status of the receiver.
Auto playback
AUTO/
DIRECT
AUTO SURROUND/
STREAM DIRECT
ALC/
STANDARD
ALC/
STANDARD SURR
Using this receiver, you can listen to any source in surround
sound. However, the options available will depend on your
speaker setup and the type of source you’re listening to.
• If the source is Dolby Digital, DTS, or Dolby Surround
encoded, the proper decoding format will automatically be
selected and shows in the display.
When you select STEREO ALC (Auto Level Control stereo
mode), this unit equalizes playback sound levels if each sound
level varies with the music source recorded in a portable
audio player.
When you select STEREO, you will hear the source through
just the front left and right speakers (and possibly your
subwoofer depending on your speaker settings). Dolby Digital
and DTS multichannel sources are downmixed to stereo.
The following modes provide basic surround sound for stereo
and multichannel sources.
Explanatory notes
No: No connected / Yes: Connected / Two: Two speakers are
connected / –: Whether connected or no
The simplest, most direct listening option is the AUTO
SURROUND feature. With this, the receiver automatically
detects what kind of source you’re playing and selects
multichannel or stereo playback as necessary.
• Press AUTO/DIRECT repeatedly until AUTO SURROUND
shows briefly in the display (it will then show the decoding
or playback format). Check the digital format indicators in
the display to see how the source is being processed.
31
See above.
STEREO ALC
DOLBY PLII MOVIE
Movie
DOLBY PLII MUSICa
Music
DOLBY PLII GAME
NEO:6 CINEMA
Listening in surround sound
Suitable sources
b
NEO:6 MUSICb
Video games
Movie
Music
DOLBY PRO LOGIC
Old movies
STEREOc
See above.
Multichannel sources
STEREO ALC
See above.
STEREOc
See above.
a. You can also adjust the C.WIDTH, DIMEN., and PNRM. effect
(see Setting the Audio options on page 34).
b. You can also adjust the C.IMG effect (see Setting the Audio
options on page 34).
c. The audio is heard with your surround settings and you can still
use the Midnight, Loudness, Phase Control, Sound Retriever
and Tone functions.
4
7
56
5
Listening to your system
Using the Advanced surround
ADV SURR
ADVANCED
SURROUND
The Advanced surround feature creates a variety of surround
effects. Try different modes with various soundtracks to see
which you like.
ACTION
Designed for action movies with dynamic
soundtracks.
DRAMA
Designed for movies with lots of dialog.
• ECO MODE will switch OFF automatically when switched
to other listening modes (Advanced surround mode and
Auto surround mode).
F.S.S.ADVANCE
(Front Stage
Surround
ADVANCE)
ADVANCED GAME Suitable for video games.
SPORTS
Suitable for sports programs.
CLASSICAL
Gives a large concert hall-type sound.
ROCK/POP
Creates a live concert sound for rock and/or
pop music.
EXT.STEREO
Gives multichannel sound to a stereo
source, using all of your speakers.
ECO MODE 1
Cut back on power consumption. Suitable
for contents that are mainly high level
(mainly music).
ECO MODE 2
Cut back on even more power consumption
than ECO MODE 1. Suitable for contents
with wider dynamic range (mainly movies).
Note
• During ECO mode, the brightness switches between 2
levels. If the dimmest level is selected, DIMMER will be
shown on the display. (Mode other than ECO: 4 levels, ECO
mode: 2 levels)
Allows you to create natural surround
sound effects using just the front speakers
and the subwoofer.
Use to provide a rich surround sound effect
directed to the center of where the front left
and right speakers sound projection area
converges.
Front left
speaker
Suitable for listening to the sound from a
Bluetooth wireless technology device.
The S.R AIR listening mode can only
selected when the ADAPTER input.
PHONES SURR
When listening through headphones, you
can still get the effect of overall surround.
AUTO/
DIRECT
AUTO SURROUND/
STREAM DIRECT
Use the Stream Direct modes when you want to hear the
truest possible reproduction of a source. All unnecessary
signal processing is bypassed.
AUTO SURROUND See Auto playback on page 31.
DIRECT
Sources are heard according to the settings
made in the Manual SP Setup (speaker
setting, channel level, speaker distance), as
well as with dual mono settings. You will
hear sources according to the number of
channels in the signal.
Phase Control, Acoustic Calibration EQ,
Sound Delay, Auto Delay, LFE Attenuate
and Center image functions are available.
PURE DIRECT
Analog and PCM sources are heard without
any digital processing.
Front right
speaker
S.R AIR (Sound
Retriever AIR)
32
Using Stream Direct
4
7
56
5
Listening to your system
Using the Sound Retriever
Listening with Acoustic Calibration EQ
Better sound using Phase Control
When audio data is removed during the compression
process, sound quality often suffers from an uneven sound
image. The Sound Retriever feature employs new DSP
technology that helps bring CD quality sound back to
compressed 2-channel audio by restoring sound pressure
and smoothing jagged artifacts left over after compression.
You can listen to sources using the Acoustic Calibration
Equalization set in Automatically setting up for surround
sound (MCACC) on page 21. Refer to these pages for more on
Acoustic Calibration Equalization.
This receiver’s Phase Control feature uses phase correction
measures to make sure your sound source arrives at the
listening position in phase, preventing unwanted distortion
and/or coloring of the sound.
Phase Control technology provides coherent sound
reproduction through the use of phase matching for an
optimal sound image at your listening position. The default
setting is on and we recommend leaving Phase Control
switched on for all sound sources.
RECEIVER SLEEP
RECEIVER SLEEP
SOURCE
1
2
3
DISP
4
5
6
CH
7
8
9
CH
CLR
0
ENTER
1
2
3
DISP
4
5
6
CH
7
8
9
CH
CLR
0
ENTER
SOURCE
RECEIVER
INPUT
RECEIVER
SHIFT
INPUT

Press RECEIVER , then press S.RETRIEVER to switch the
S.RTV (Sound Retriever) ON or OFF.
Note
• The Sound Retriever is only applicable to 2-channel
sources.

SHIFT
While listening to a source, press RECEIVER , then press
EQ to switch the EQ (Acoustic Calibration EQ) ON or
OFF.
The MCACC indicator on the front panel lights when
Acoustic Calibration EQ is active.
• You can’t use Acoustic Calibration EQ with Stream
Direct mode and it has no effect with headphones.
RECEIVER SLEEP
1
2
3
DISP
4
5
6
CH
7
8
9
CLR
0
ENTER
SOURCE
RECEIVER
INPUT
CH
SHIFT
listening to a source, press
, then press
 While
PHASE to switch the P.CTL (Phase Control) ON or OFF.
RECEIVER
Note
• Phase matching is a very important factor in achieving
proper sound reproduction. If two waveforms are ‘in phase’,
they crest and trough together, resulting in increased
amplitude, clarity and presence of the sound signal. If a
crest of a wave meets a trough, then the sound will be ‘out
of phase’ and an unreliable sound image will be produced.
• If your subwoofer has a phase control switch, set it to the
plus (+) sign (or 0°). However, the effect you can actually
feel when Phase Control is set to ON on this receiver
depends on the type of your subwoofer. Set your subwoofer
to maximize the effect. It is also recommended you try
changing the orientation or the place of your subwoofer.
• Set the built-in lowpass filter switch of your subwoofer to
OFF. If this cannot be done on your subwoofer, set the
cutoff frequency to a higher value.
• If the speaker distance is not properly set, you may not have
a maximized Phase Control effect.
• The Phase Control mode cannot be set to ON in the
following cases:
- When the PURE DIRECT mode is switched on.
- When the headphones are connected.
33
4
7
56
5
Listening to your system
Setting/What it does
Setting the Audio options
There are a number of additional sound settings you can
make using the AUDIO PARAMETER menu. The defaults, if
not stated, are listed in bold.
Important
• Note that if a setting doesn’t appear in the AUDIO
PARAMETER menu, it is unavailable due to the current
source, settings and status of the receiver.
AUDIO
PARAMETER
INPUT
ENTER
HOME
MENU
PTY
iPod CTRL
T U NE
PRESET
RECEIVER
BAND
RETURN
MUTE
1
/ to select the setting you want to adjust.
2 Use
Depending on the current status/mode of the receiver,
Press RECEIVER , then press AUDIO PARAMETER.
certain options may not be able to be selected. Check the
table below for notes on this.
/ to set it as necessary.
3 Use
See the table below for the options available for each
setting.
S.DELAY (Sound Delay)
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding
a bit of delay, you can adjust the sound to
match the presentation of the video.
MIDNIGHT/LOUDNESSa
The MIDNIGHT allows you to hear effective
surround sound of movies at low volumes.
The LOUDNESS is used to get good bass and
treble from music sources at low volumes.
TOOLS
MENU
TUNE
TOP
MENU
SOURCE
PRESET
RECEIVER SLEEP
Option(s)
EQ (Acoustic Calibration EQ)
Switches on/off the effect of Acoustic
Calibration EQ.
S.RTV (Sound Retriever)b
When audio data is removed during the
compression process, sound quality often
suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
technology that helps bring CD quality sound
back to compressed 2-channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
DUAL MONOd
Specifies how dual mono encoded Dolby
Digital soundtracks should be played.
4 Press RETURN to confirm and exit the menu.
ON
OFF
0 to 500 ms (1
step : 5 ms)
Default: 0
M/L OFF
MIDNIGHT
LOUDNESS
OFFc
ON
34
DRC (Dynamic Range Control)
Adjusts the level of dynamic range for movie
soundtracks optimized for Dolby Digital, DTS,
Dolby Digital Plus, Dolby TrueHD, DTS-HD
and DTS-HD Master Audio (you may need to
use this feature when listening to surround
sound at low volumes).
LFE ATT (LFE Attenuate)
Some Dolby Digital and DTS audio sources
include ultra-low bass tones. Set the LFE
attenuator as necessary to prevent the ultralow bass tones from distorting the sound from
the speakers.
The LFE is not limited when set to 0 dB, which
is the recommended value. When set to –15
dB, the LFE is limited by the respective
degree. When OFF is selected, no sound is
output from the LFE channel.
SACD G. (SACD Gain)f
Brings out detail in SACDs by maximizing the
dynamic range (during digital processing).
CH1 – Channel 1
is heard only
CH2 – Channel 2
is heard only
CH1 CH2 – Both
channels heard
from front
speakers
F.PCM (Fixed PCM)
This is useful if you find there is a slight delay
before OFF recognizes the PCM signal on a
CD, for instance.
When ON is selected, noise may be output
during playback of non-PCM sources. Please
select another input signal if this is a problem.
Setting/What it does
OFF
ON
HDMI (HDMI Audio)
Specifies the routing of the HDMI audio signal
out of this receiver (AMP) or through to a TV
(THRU). When THRU is selected, no sound is
output from this receiver.
The HDMI Audio setting cannot be switched
while performing synchronized amp mode
operations (page 49).
Option(s)
AUTOe
MAX
MID
OFF
0 (0 dB)
5 (–5 dB)
10 (–10 dB)
15 (–15 dB)
20 (–20 dB)
** (OFF)
0 (0 dB)
+6 (+6 dB)
AMP
THRU
A.DLY (Auto Delay)g
This feature automatically corrects the audioto-video delay between components
connected with an HDMI cable. The audio
delay time is set depending on the operational
status of the display connected with an HDMI
cable. The video delay time is automatically
adjusted according to the audio delay time.
OFF
C.WIDTH (Center Width)h
(Applicable only when using a center speaker)
Spreads the center channel between the front
right and left speakers, making it sound wider
(higher settings) or narrower (lower settings).
0 to 7
Default: 3
ON
4
7
56
5
Listening to your system
Setting/What it does
4
Option(s)
DIMEN (Dimension)
Adjusts the surround sound balance from
front to back, making the sound more distant
(minus settings), or more forward (positive
settings).
–3 to +3
Default: 0
PNRM. (Panorama)h
Extends the front stereo image to include
surround speakers for a ‘wraparound’ effect.
OFF
h
7
56
ON
0 to 10
C.IMG (Center
(Applicable only when using a center speaker) Default: 3 (NEO:6
MUSIC), 10
Adjust the center image to create a wider
(NEO:6 CINEMA)
stereo effect with vocals. Adjust the effect
from 0 (all center channel sent to front right
and left speakers) to 10 (center channel sent
to the center speaker only).
Image)i
a. You can change the MIDNIGHT/LOUDNESS options at any
time by using MIDNIGHT button.
b. You can change the Sound Retriever feature at any time by
using S.RETRIEVER button.
c. The default setting when the iPod/USB, ADAPTER,
NETRADIO, M.SERVER or FAVORITE input is selected is ON.
d. This setting works only with dual mono encoded Dolby Digital
and DTS soundtracks.
e. The initial set AUTO is only available for Dolby TrueHD signals.
Select MAX or MID for signals other than Dolby TrueHD.
f. You shouldn’t have any problems using this with most SACD
discs, but if the sound distorts, it is best to switch the gain
setting back to 0 dB.
g. This feature is only available when the connected display
supports the automatic audio/video synchronizing capability
(‘lip-sync’) for HDMI. If you find the automatically set delay time
unsuitable, set A.DLY to OFF and adjust the delay time
manually. For more details about the lip-sync feature of your
display, contact the manufacturer directly.
h. Only available with 2-channel sources in DOLBY PLII MUSIC
mode.
i. Only when listening to 2-channel sources in NEO:6 CINEMA
and NEO:6 MUSIC mode.
35
Chapter
6
Playback with NETWORK features
Introduction
This receiver is equipped with the LAN terminal and you can
enjoy the following features by connecting your components
to these terminals.
Listening to Internet radio stations
You can select and listen to your favorite Internet radio station
from the list of Internet radio stations created, edited, and
managed by the vTuner database service exclusively for use
with the Pioneer products.
See Playback with Network functions on page 37 and Listening
to Internet radio stations on page 38.
Playback the music files stored in Computer
You can playback a lot of musics stored in your Computer
using this unit.
• Besides a Computer, you can also play back audio files
stored on your other components with the built-in media
server function based on DLNA 1.0 or DLNA 1.5 framework
and protocols (i.e. network-capable hard disks and audio
systems).
See Playback with Network functions on page 37 and Playing
back audio files stored on components on the network on
page 38.
Note
• To listen to Internet radio stations, you must sign a contract
with an ISP (Internet Service Provider) beforehand.
• Photo or video files cannot be played back.
• With Windows Media Player 11 or Windows Media Player
12, you cannot play back copyrighted audio files on this
receiver.
About playable DLNA network devices
This unit allows you to play music on media servers connected
on an identical Local Area Network (LAN) as the receiver. This
unit allows for the playing of files stored on the following
devices:
• Computer running Microsoft Windows Vista or XP with
Windows Media Player 11 installed
• Computer running Microsoft Windows 7 with Windows
Media Player 12 installed
• DLNA-compatible digital media servers (on Computer or
other components)
Files stored in a Computer or DMS (Digital Media Server) as
described above can be played via command from an external
Digital Media Controller (DMC). Devices controlled by this
DMC to play files are called DMRs (Digital Media Renderers).
This receiver supports this DMR function. When in the DMR
mode, such operations as playing and stopping files can be
performed from the external controller. Volume adjustment
and the muting control are also possible.
• Depending on the external controller being used, playback
may be interrupted when the volume is adjusted from the
controller. In this case, adjust the volume from the receiver
or remote control.
Using AirPlay on iPod touch, iPhone, iPad, and
iTunes
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion, and Mac and PC
with iTunes 10.2.2 or later.
To use AirPlay, select your receiver on your iPod touch,
iPhone, iPad or in iTunes. *1
The receiver’s input will switch automatically to AirPlay when
AirPlay is in use. *2
The following operations can be performed when in AirPlay
mode:
• Adjustment of the receiver’s volume from iPod touch,
iPhone, iPad or iTunes.
36
• Pause/resume, next/previous track, and shuffle/repeat
from the remote control of the receiver. (Press NETWORK
to switch the remote control to the network operation
mode.)
*1: For more information, see the Apple website (http://
www.apple.com).
*2: The receiver’s power automatically turns on when
Network Standby is set to ON (page 47).
Note
• A network environment is required to use AirPlay.
• AirPlay provided on this receiver has been developed and
tested based on the software versions for the iPod, iPhone,
iPad and the software versions for iTunes that are indicated
on the Pioneer website. AirPlay may not be compatible with
iPod, iPhone, iPad or iTunes software versions other than
those indicated on the Pioneer website.
About the DHCP server function
To play back audio files stored on components on the network
or listen to Internet radio stations, you must turn on the DHCP
server function of your router. In case your router does not
have the built-in DHCP server function, it is necessary to set
up the network manually. Otherwise, you cannot play back
audio files stored on components on the network or listen to
Internet radio stations. See The Network Setup menu on
page 39 for more on this.
Authorizing this receiver
This receiver must be authorized to enable playback. This
happens automatically when the receiver makes a connection
over the network to the PC. If not, please authorize this
receiver manually on the PC. The authorization (or
permission) method for access varies depending on the type
of server currently being connected. For more information on
authorizing this receiver, refer to the instruction manual of
your server.
4
7
56
6
This receiver features “HTC Connect”, a simple way to enjoy
music content from your HTC Connect certified smart phone.
1 HTC Connect music streaming provided on this product
has been developed based on interoperability testing as
defined by the HTC Connect Certification program with
the HTC Connect-compatible smartphones.
2 Music Navigation via the music progress bar is not
currently supported with HTC Connect.
3 Third party music applications (those other than HTC’s
pre-installed “Music” app) have not been tested for
compatibility and may not work. HTC Connect has been
tested with MP3, AAC, WMA and WAV encoding
formats. Other formats may not be compatible.
4 High network congestion may interfere with the
operation of HTC Connect.
HTC Connect Certified Smartphones
Important
• In case a domain is configured in a Windows network
environment, you cannot access a PC on the network while
you are logged onto the domain. Instead of logging onto the
domain, log onto the local machine.
• There are cases where the time elapsed may not be
correctly displayed.
• About one minute is required between turning the power
on and completion of startup.
NETWORK repeatedly to select the category you
1 Press
want to play back.
It may take several seconds for this receiver to access the
network.
Select a category from the following list:
• NETRADIO – Internet radio
- When NETRADIO is selected, the radio station that
was playing last time is played.
• M.SERVER – Server components on the network
(Media server)
• FAVORITE – Favorite songs currently being registered
Depending on the selected category, the names of
folders, files, and Internet radio stations are displayed.
Use / to select the folder, music files or Internet
2 radio
station to play back, and then press ENTER.
Press / to scroll up and down the list and select the
desired item. When you press ENTER, playback starts
with the playback screen being displayed for the selected
item. To return to the list screen, press RETURN.
When the list screen is displayed from the playback
screen, the playback screen reappears automatically if
no operation is performed for 10 seconds while the list
screen is displayed.
Only audio files with the
mark can be played. In case
of the folders with the
mark, use / and ENTER to
select the desired folder and audio files.
• When  or  is pressed at the list screen, the
page switches.
37
step 2 to play back the desired song.
3 Repeat
4
For detailed operating instructions, refer to the section
shown below.
• Internet radio stations – See Listening to Internet radio
stations below.
• Media server – See Playing back audio files stored on
components on the network on page 38.
• Favorites – See Playing back your favorite songs on
page 38.
Basic playback controls
You can perform the following operations with the remote
control of this receiver. Note that some buttons are not
available for operation depending on the category currently
being played back.
NETWORK to switch the remote control to the
 Press
NETRADIO, M.SERVER or FAVORITE operation mode.
MUTE
AUDIO
PARAMETER
TOOLS
MENU
TUNE
TOP
MENU
ENTER
HOME
MENU
PTY
iPod CTRL
TUNE
PRESET
The HTC Connect-compatible smartphones, Please check
Pioneer website for up to date information about compatible
devices and audio format support.
http://www.pioneer.com.sg (for Southeast Asia)
http://www.pioneer.com.au (for Australia)
http://www.pioneerhongkong.com.hk (for Hong Kong)
http://www.pioneer-twn.com.tw (for Taiwan)
Specifications and design subject to modification without
notice.
HTC, HTC Connect and the HTC Connect logo are trademarks
of HTC Corporation.
Playback with Network functions
PRESET
About HTC Connect
Playback with NETWORK features
1
2
3
DISP
4
5
6
CH
7
8
9
CLR
0
ENTER
CH
SHIFT
BAND
RETURN
MUTE
7
56
6
Listening to Internet radio stations
Internet radio is an audio broadcasting service transmitted via
the Internet. There are a large number of Internet radio
stations broadcasting a variety of services from every corner
of the world. Some are hosted, managed, and broadcast by
private individuals while others are by the corresponding
traditional terrestrial radio stations or radio networks.
Whereas terrestrial, or OTA (over-the-air), radio stations are
geographically restricted on the range of radio waves
broadcast from a transmitter through the air, Internet radio
stations are accessible from anywhere in the world, as long as
there is a connection to the Internet, as services are not
transmitted through the air but are delivered over the World
Wide Web. On this receiver you can select Internet radio
stations by genre as well as by region.
Depending on the Internet line conditions, the sound may not
be smooth when playing Internet radio.
About list of Internet radio
The list of Internet radio stations on this receiver is created,
edited, and managed by the vTuner database service
exclusively for use with this receiver. For details about vTuner,
see vTuner on page 43.
Saving and retrieving Internet radio stations
You can easily save and retrieve saved Internet radio stations.
See Playing back your favorite songs on page 38 for more on
this.
• To listen to Internet radio stations, you must have highspeed broadband Internet access. With a 56 K or ISDN
modem, you may not enjoy the full benefits of Internet
radio.
• The port number varies depending on the Internet radio
station. Check the firewall settings.
• A list of Internet radio stations provided by the vTuner
database service is subject to change or deletion without
notice due to various reasons.
• Broadcasts may be stopped or interrupted depending on
the Internet radio station. In this case, you cannot listen to
a radio station selected from the list of Internet radio
stations.
Playback with NETWORK features
Registering broadcast stations not on the vTuner list
from the special Pioneer site
With the receiver, broadcast stations not included on the list
of station distributed by vTuner can be registered and played.
Check the access code required for registration on the
receiver, use this access code to access the special Pioneer
Internet radio site and register the desired broadcast stations
in your favorites. The address of the special Pioneer Internet
radio site is:
http://www.radio-pioneer.com
the Internet Radio list screen.
1 Display
To display the Internet Radio list screen, perform step 1 at
Playback with Network functions on page 37.
2 Use / to select ‘Help’, then press ENTER.
/ to select ‘Get access code’, then press ENTER.
3 Use
The access code required for registration on the special
Pioneer Internet radio site is displayed. Make a memo of
this address.
The following can be checked on the Help screen:
• Get access code – The access code required for
registration on the special Pioneer Internet radio site is
displayed.
• Show Your WebID/PW – After registering on the
special Pioneer Internet radio site, the registered ID
and password are displayed.
• Reset Your WebID/PW – Resets all the information
registered on the special Pioneer Internet radio site.
When reset, all the registered broadcast stations are
also cleared. If you want to listen to the same stations,
re-register after resetting.
the special Pioneer Internet radio site from your
4 Access
computer and perform the registration process.
http://www.radio-pioneer.com
Access the above site and use the access code in step 3
to perform user registration, following the instructions on
the screen.
38
the desired broadcast stations as your
5 Register
favorites, following the instructions on the computer’s 4
screen.
Both broadcast stations not on the vTuner list and
stations on the vTuner list can be registered. In this case
they are registered on the receiver as favorite broadcast
stations and can be played.
Playing back audio files stored on components on
the network
This unit allows you to play music on media servers connected
on an identical Local Area Network (LAN) as the receiver. This
unit allows for the playing of files stored on the following
devices:
• Computer running Microsoft® Windows Vista® or
Windows XP with Windows Media Player 11 installed
• Computer running Microsoft Windows 7 with Windows
Media Player 12 installed
• DLNA-compatible digital media servers (on Computer or
other components)
Playing back your favorite songs
Up to 64 favorite tracks on the media server and/or Internet
radio stations can be registered in the Favorites folder. Note
that only the audio files stored on components on the network
can be registered.
Registering and deleting audio files and Internet
radio stations in and from the Favorites folder
NETWORK to switch the remote control to the
1 Press
M.SERVER or NETRADIO operation mode.
the track or Internet radio station you want to
2 With
register selected, press +Favorite.
The selected song or Internet radio station is then
registered in the Favorite.
Note
• To delete a registered song, select the Favorites folder,
select the song you want to delete from the folder, and
press CLEAR. The selected song is then deleted from the
Favorites folder.
7
56
6
Playback with NETWORK features
The Network Setup menu
Network Configuration
Setting up the network to listen to Internet radio on this
receiver.
IP address/Proxy setting
1
HOME MENU.
2 Press
Network Setup menu appears on your TV. Use ///
Press NETWORK.
 and ENTER on the remote control to navigate through
the screens and select menu items. Press RETURN to
exit the current menu.
• Press HOME MENU at any time to exit the Network
Setup menu.
the setting you want to adjust.
3 Select
• Network Configuration
- IP Address, Proxy – Sets up the IP address/Proxy of
•
•
•
•
this receiver (see below).
- Friendly Name – The name of the receiver displayed
on a computer or other device connected to the
network can be changed (see below).
- Parental Lock – Restricts usage of network
functions (page 40).
Language – Language can be set the NETWORK
function OSD screen (page 40).
Firmware Update – Use to update the receiver’s
firmware and check the version (page 40).
Factory Reset – Use to reset all network connection
settings to their initial, factory-setting condition
(page 42).
System Info – You can check the network settings of
this receiver (page 42).
In case the router connected to the LAN terminal on this
receiver is a broadband router (with a built-in DHCP server
function), simply turn on the DHCP server function, and you
will not need to set up the network manually. You must set up
the network as described below only when you have
connected this receiver to a broadband router without a
DHCP server function. Before you set up the network, consult
with your ISP or the network manager for the required
settings. It is advised that you also refer to the operation
manual supplied with your network component.
• IP Address
The IP address to be entered must be defined within the
following ranges. If the IP address defined is beyond the
following ranges, you cannot play back audio files stored on
components on the network or listen to Internet radio
stations.
Class A: 10.0.0.1 to 10.255.255.254
Class B: 172.16.0.1 to 172.31.255.254
Class C: 192.168.0.1 to 192.168.255.254
• Subnet Mask
In case an xDSL modem or a terminal adapter is directly
connected to this receiver, enter the subnet mask provided
by your ISP on paper. In most cases, enter 255.255.255.0.
• Default Gateway
In case a gateway (router) is connected to this receiver,
enter the corresponding IP address.
• Primary DNS Server/Secondary DNS Server
In case there is only one DNS server address provided by
your ISP on paper, enter it in the “Primary DNS Server”
field. In case there are more than two DNS server
addresses, enter “Secondary DNS Server” in the other
DNS server address field.
• Proxy Hostname/Proxy Port
This setting is required when you connect this receiver to
the Internet via a proxy server. Enter the IP address of your
proxy server in the “Proxy Hostname” field. Also, enter the
port number of your proxy server in the “Proxy Port” field.
39
‘Network Configuration’ from the Network
1 Select
4
Setup menu.
‘IP Address, Proxy’ from the Network
2 Select
Configuration menu.
7
the DHCP setting you want.
3 Select
When you select ON, the network is automatically set up,
and you do not need to follow Steps 4. Proceed with Step
5.
If there is no DHCP server on the network and you select
ON, this receiver will use its own Auto IP function to
determine the IP address.
• The IP address determined by the Auto IP function is
169.254.X.X. You cannot listen to an Internet radio
station if the IP address is set for the Auto IP function.
the IP Address, Subnet Mask, Default Gateway,
4 Enter
Primary DNS Server and Secondary DNS Server.
Press / to select a number and / to move the
cursor.
‘OFF’ or ‘ON’ for the Enable Proxy Server setting
5 Select
to deactivate or activate the proxy server.
In case you select OFF, proceed with Step 8. In case you
select ON, on the other hand, proceed with Step 6.
the address of your proxy server or the domain
6 Enter
name.
Use / to select a character, / to set the position,
and ENTER to confirm your selection.
the port number of your proxy server.
7 Enter
Use / to select a character, / to set the position,
and ENTER to confirm your selection.
8 Select ‘OK’ to confirm the IP Address/Proxy setup.
56
6
Playback with NETWORK features
Friendly Name
Language
1
1 Select ‘Language’ from the Network Setup menu.
‘Friendly Name’ from the Network Configuration
2 Select
menu.
2 Select the language you want.
you’re finished, press RETURN.
‘Edit Name’ then select ‘Rename’.
3 When
3 Select
You return to the Network Setup menu.
If after changing the name you want to restore the name
Select ‘Network Configuration’ from the Network
Setup menu.
to the default, select Default.
the name you want.
4 Input
Use / to select a character, / to set the position,
and ENTER to confirm your selection.
Parental Lock
Set restrictions for using Internet services. Also set the
password accompanying the usage restrictions.
• Upon shipment from the factory, the password is set to
“0000”.
‘Network Configuration’ from the Network
1 Select
Setup menu.
‘Parental Lock’ from the Network Configuration
2 Select
menu.
the password.
3 Input
Use / to select a character, / to set the position,
and ENTER to confirm your selection.
whether to turn Parental Lock on or off.
4 Specify
• OFF – Internet services are not restricted.
• ON – Internet services are restricted.
5
If you want to change the password, select ‘Change
Password’.
In this case, the procedure returns to step 3.
Language can be set on the NETWORK function OSD screen.
Firmware Update
Use this procedure to update the receiver’s firmware.
If an update file does not exist in the Pioneer’s website,
updating the firmware for the receiver is not necessary.
Updating via a USB memory device is performed by
downloading the update file from a computer, reading this file
onto a USB memory device then inserting this USB memory
device into the USB port on the receiver’s front panel. With
this procedure, the USB memory device containing the
update file must first be inserted into the USB port on the
receiver’s front panel.
• If an update file is provided on the Pioneer website,
download it onto your computer. When downloading an
update file from the Pioneer website onto your computer,
the file will be in ZIP format. Unzip the ZIP file before saving
it on the USB memory device. If there are any old
downloaded files or downloaded files for other models on
the USB memory device, delete them.
Important
• DO NOT unplug the power cord during updating.
• Do not disconnect the USB memory device during
updating.
• Verify the firmware version of the receiver in the System
Info menu before updating and confirm that the firmware
in the USB memory device is a newer version.
• Updating may reset the receiver’s settings to the initial,
factory-setting condition. Whether this is applicable to your
receiver can be confirmed at our Pioneer website.
40
‘Firmware Update’ from the Network Setup
1 Select
menu.
The receiver checks whether the USB memory device
inserted into the USB port on the receiver’s front panel
contains updatable firmware.
2
‘Updating in progress, don’t unplug!’ is
3 When
displayed, select ‘Start’.
To update, select ‘Start’.
• If ‘File Not Found’ is displayed, try the following:
- No update file was found on the USB memory
device. Store the file in the USB memory device’s
root directory.
- Try disconnecting then reconnecting the USB device
or storing the update file again. If the error still
occurs, try using a different USB memory device.
firmware update will start. Please wait.
4 The
The OSD display will turn off during update and the words
‘UPDATE’ will flash on the front panel.
is displayed, updating is completed.
5 IfThe‘COMPLETE’
screen will return automatically to the play screen.
• If ‘FAIL’ is displayed on the front panel display,
updating has failed. Try the following:
- Turn the receiver’s power off, then turn it back on
and try updating the firmware again.
- Try disconnecting then reconnecting the USB device
or storing the update file again. If the error still
occurs, try using a different USB memory device.
4
7
56
6
Playback with NETWORK features
Network setting using Safari browser
Friendly Name setting using Safari browser
1 Launch Safari on your computer.
Bookmark icon. Click Bonjour list (a), and then
2 Press
select this receiver’s name (Friendly Name) (b) in
1 Launch Safari on your computer.
Bookmark icon. Click Bonjour list (a), and then
2 Press
select this receiver’s name (Friendly Name) (b) in
Bookmark.
If Bonjour list is not displayed, access the IP address
“http://(the receiver's IP address)” from Safari.
3 Click Firmware Update.
7
Bookmark.
3 Click Friendly Name.
4 Enter friendly name and then press Apply.
56
a
Start.
4 Press
The firmware update prepare screen is displayed. If the
b
screen does not switch automatically, click Click here.
3 Click IP, Proxy Setting.
the network settings manually and then press
4 Setup
Apply.
Note
• This setting for the network has been confirmed for Mac OS
X 10.7 and Safari 5.1.
Firmware update using Safari browser
1 Launch Safari on your computer.
Bookmark icon. Click Bonjour list (a), and then
2 Press
select this receiver’s name (Friendly Name) (b) in
Bookmark.
Note
• This setting for the network has been confirmed for Mac OS
X 10.7 and Safari 5.1.
41
4
6
Playback with NETWORK features
the latest firmware on your computer (a) and
5 Browse
then press Upload (b).
The extension of the firmware is fw. Please select a file
that has the fw extension.
The confirmation screen is displayed. If you continue the
firmware update, press OK. Once the firmware update
process starts, you can't stop it. Wait until the file is
uploaded (about one minute may be required depending
on your LAN connection environment).
Factory Reset
Use to reset all network connection settings to their initial,
factory-setting condition.
1 Select ‘Factory Reset’ from the Network Setup menu.
2 Select ‘Start’.
‘OK’ to confirm.
3 Select
The screen will return automatically to the play screen.
System Information
b
a
The setting status of the following network-related items can
be checked.
• IP Address – Check the IP address of this receiver.
• MAC Address – Check the MAC address of this receiver.
• Release ID – Check the firmware version of this receiver.
‘System Info’ from the Network Setup menu.
1 Select
Display the setting status of the network-related items.
you’re finished, press RETURN.
2 When
You return to the Network Setup menu.
firmware upload status screen is displayed.
6 The
“The upload process finished successfully.” will be shown
when the update is completed.
Unplug the power cord from the AC outlet after the
update is completed.
42
About network playback
The network playback function of this unit uses the following
technologies:
Windows Media Player
See Windows Media Player 11/Windows Media Player 12 on
page 43 for more on this.
4
7
56
6
DLNA
DLNA CERTIFIED™ Audio Player
The Digital Living Network Alliance (DLNA) is a cross-industry
organization of consumer electronics, computing industry
and mobile device companies. Digital Living provides
consumers with easy sharing of digital media through a wired
or wireless network in the home.
The DLNA certification logo makes it easy to find products
that comply with the DLNA Interoperability Guidelines. This
unit complies with DLNA Interoperability Guidelines v1.5.
When a PC running DLNA server software or other DLNA
compatible device is connected to this player, some setting
changes of software or other devices may be required. Please
refer to the operating instructions for the software or device
for more information.
DLNA™, the DLNA Logo and DLNA CERTIFIED™ are
trademarks, service marks, or certification marks of the Digital
Living Network Alliance.
Content playable over a network
• Even when encoded in a compatible format, some files may
not play correctly.
• Movie or Photo files cannot be played back.
• There are cases where you cannot listen to an Internet radio
station even if the station can be selected from a list of
radio stations.
• Some functions may not be supported depending on the
server type or version used.
• Supported file formats vary by server. As such, files not
supported by your server are not displayed on this unit. For
more information check with the manufacturer of your
server.
Playback with NETWORK features
Disclaimer for Third Party Content
Access to content provided by third parties requires a high
speed internet connection and may also require account
registration and a paid subscription.
Third party content services may be changed, suspended,
interrupted, or discontinued at any time without notice, and
Pioneer disclaims any liability in connection with such
occurrences.
Glossary
aacPlus
AAC decoder uses aacPlus developed by Coding Technologies.
(www.codingtechnologies.com)
FLAC
• Playback may stall when the PC is switched off or any
media files stored on it are deleted while playing content.
• If there are problems within the network environment
(heavy network traffic, etc.) content may not be displayed or
played properly (playback may be interrupted or stalled).
For best performance, a 100BASE-TX connection between
player and PC is recommended.
• If several clients are playing simultaneously, as the case
may be, playback is interrupted or stalled.
• Depending on the security software installed on a
connected PC and the setting of such software, network
connection may be blocked.
Pioneer is not responsible for any malfunction of the player
and/or the NETWORK features due to communication error/
malfunctions associated with your network connection and/
or your PC, or other connected equipment. Please contact
your PC manufacturer or Internet service provider.
This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a license
from Microsoft Licensing, Inc.
Microsoft, Windows, Windows Media and Windows Vista are
either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
FLAC (Free Lossless Audio Codec) is an audio format allows
lossless codec. Audio is compressed in FLAC without any loss
in quality. For more details about FLAC, visit the following
website: http://flac.sourceforge.net/
vTuner
vTuner is a paid online database service that allows you to
listen to radio and TV broadcasts on the Internet. vTuner lists
thousands of stations from over 100 different countries
around the globe. For more detail about vTuner, visit the
following website:
http://www.radio-pioneer.com
“This product is protected by certain intellectual property rights
of NEMS and BridgeCo. Use or distribution of such technology
outside of this product is prohibited without a license from
NEMS and BridgeCo or an authorized subsidiary.”
Windows Media
Windows Media is a multimedia framework for media
creation and distribution for Microsoft Windows. Windows
Media is either a registered trademark or trademark of
Microsoft Corporation in the U.S. and/or other countries. Use
an application licensed by Microsoft Corporation to author,
distribute, or play Windows Media formatted content. Using
an application unauthorized by Microsoft Corporation is
subject to malfunction.
Windows Media Player 11/Windows Media Player 12
Windows Media Player is software to deliver music, photos
and movies from a Microsoft Windows computer to home
stereo systems and TVs.
43
7
56
Pioneer does not represent or warrant that content services
will continue to be provided or available for a particular period
of time, and any such warranty, express or implied, is
disclaimed.
About playback behavior over a network
4
6
With this software, you can play back files stored on the PC
through various devices wherever you like in your home.
This software can be downloaded from Microsoft’s website.
• Windows Media Player 11 (for Windows XP or Windows
Vista)
• Windows Media Player 12 (for Windows 7)
For more information check the official Microsoft website.
Playback with NETWORK features
AAC (MPEG-4 AAC LC, MPEG-4 HE AAC (aacPlus v1/2))
About playable file formats
The NETWORK feature of this receiver supports the following
file formats. Note that some file formats are not available for
playback although they are listed as playable file formats.
Also, the compatibility of file formats varies depending on the
type of server. Check with your server to ensure the
compatibility of file formats supported by your server.
• Internet radio playback may be affected by the Internet
communications environment, and in this case playback
may not be possible even with the file formats listed here.
• With WAV, FLAC, AIFF and Apple Lossless files, when
music files with the same format, sampling frequency,
quantization bit number and number of channels are
played successively, they are played with no gap.
- Gapless playback is not possible when the format is
being converted (transcoded) by the server.
- Gapless playback is not possible in the DMR mode.
.m4a
.aac
.3gp
.3g2
32 kHz, 44.1 kHz, 48 kHz
Quantization bitrate
16 bit
2 ch
Bitrate
8 kbps to 320 kbps
VBR/CBR
Supported/Supported
WAV (LPCM)
.wav
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bitrate
16 bit, 24 bit
Channel
2 ch
WMA (WMA2/7/8/9)
.wmab
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz
Quantization bitrate
16 bit
Channel
2 ch
Bitrate
5 kbps to 320 kbps
VBR/CBR
Supported/Supported
44
16 bit
Channel
Bitrate
.flacc
2 ch
16 kbps to 320 kbps
Supported/Supported
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Quantization bitrate
16 bit, 24 bit
Channel
2 ch
AIFF
.aif
.aiff
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz
Quantization bitrate
16 bit, 24 bit
Channel
Sampling frequency
Channel
Quantization bitrate
VBR/CBR
Stream
MP3 (MPEG-1 Audio Layer 3)
.mp3a
32 kHz, 44.1 kHz, 48 kHz
FLAC
Music files
Extension
Sampling frequency
2 ch
Apple Lossless
.m4a
.mp4
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz
Quantization bitrate
16 bit, 24 bit
Channel
2 ch
a. MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.
b. Files encoded using Windows Media Codec 9 may be playable
but some parts of the specification are not supported;
specifically, Pro, Lossless, Voice.
c. Uncompressed FLAC files are not supported. Pioneer does not
guarantee playback.
4
7
56
Chapter
7
Home Menu
Using the Home Menu
The following section shows you how to make detailed
settings to specify how you’re using the receiver, and also
explains how to fine-tune individual speaker system settings
to your liking.
Important
• The OSD will not appear if you have connected using the
composite output to your TV. Use HDMI connection for
Home Menu.
• If headphones are connected to the receiver, disconnect
them.
• You can’t use the Home Menu when the NETRADIO,
M.SERVER, FAVORITE, iPod/USB or ADAPTER input is
selected.
AUDIO
PARAMETER
PRESET
SOURCE
ENTER
HOME
MENU
PTY
iPod CTRL
TUNE
PRESET
RECEIVER SLEEP
TOOLS
MENU
TUNE
TOP
MENU
RECEIVER
INPUT
BAND
RETURN
MUTE
on the receiver and your TV.
1 Switch
Press RECEIVER to switch on.
the TV input to the input that connects this
2 Switch
receiver to the TV through the corresponding HDMI
cable.
, then press HOME MENU.
3 Press
The Home Menu appears on your TV. Use /// and
RECEIVER
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
• Press HOME MENU at any time to exit the Home
Menu.
4 Select the setting you want to adjust.
Home Menu
1 . Auto MCACC
2 . Manual SP Setup
3 . Input Assign
4. Auto Power Down
5. HDMI Setup
6. Network Standby
7. MHL Setup
8. OSD Setup
• Auto MCACC – This is a quick and effective automatic
surround setup (see Automatically setting up for surround
sound (MCACC) on page 21).
• Manual SP Setup
- Speaker Setting – Specify the size and number of
speakers you’ve connected (see below).
- X.Over – Specify which frequencies will be sent to the
subwoofer (page 46).
- Channel Level – Adjust the overall balance of your
speaker system (page 46).
- Speaker Distance – Specify the distance of your
speakers from the listening position (page 47).
• Input Assign
- Analog Input – Specify what you’ve connected to the
ANALOG IN1 audio input (page 47).
• Auto Power Down – Sets to automatically turn off the
power when the receiver has not operated for several hours
(see The Auto Power Down menu on page 47).
• HDMI Setup – Set the audio return channel function or set
the HDMI input signal to Standby Through output or not
during standby (see HDMI Setup on page 49).
• Network Standby – Allows the AirPlay function to be used
even when the receiver is in the standby mode (see The
Network Standby menu on page 47).
• MHL Setup – Changes the settings related to MHL.
• OSD Setup – Sets the overlay function ON/OFF.
45
Manual speaker setup
This receiver allows you to make detailed settings to optimize
the surround sound performance. You only need to make
these settings once (unless you change the placement of your
current speaker system or add new speakers).
These settings are designed to fine-tune your system, but if
you’re satisfied with the settings made in Automatically
setting up for surround sound (MCACC) on page 21, it isn’t
necessary to make all of these settings.
Speaker Setting
Use this setting to specify your speaker configuration (size,
number of speakers). It is a good idea to make sure that the
settings made in Automatically setting up for surround sound
(MCACC) on page 21 are correct.
1 Select ‘Manual SP Setup’ from the Home Menu.
‘Speaker Setting’ from the Manual SP Setup
2 Select
menu.
2a . S peaker S etti ng
2 . Manual S P S etup
a.
b.
c.
d.
S peaker S etti ng
X . Over
Channel Level
S peaker Di stance
Return
S MALL
Front
Center
[ SMALL ]
S urr
[ SMALL ]
S urr. Back [
NO
]
S ubwoofer:
YES
Return
the set of speakers that you want to set then
3 Choose
select a speaker size.
Use / to select the size (and number) of each of the
following speakers:
• Front – Select LARGE if your front speakers reproduce bass
frequencies effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass frequencies to
the subwoofer.
• Center – Select LARGE if your center speaker reproduces
bass frequencies effectively, or select SMALL to send bass
frequencies to the other speakers or subwoofer. If you
didn’t connect a center speaker, choose NO (the center
channel is sent to the other speakers).
4
7
56
7
• Surr – Select LARGE if your surround speakers reproduce
bass frequencies effectively. Select SMALL to send bass
frequencies to the other speakers or subwoofer. If you
didn’t connect surround speakers choose NO (the sound of
the surround channels is sent to the other speakers).
• Subwoofer – LFE signals and bass frequencies of
channels set to SMALL are output from the subwoofer
when YES is selected (see notes below). Choose the PLUS
setting if you want the subwoofer to output bass sound
continuously or you want deeper bass (the bass
frequencies that would normally come out the front and
center speakers are also routed to the subwoofer). If you did
not connect a subwoofer choose NO (the bass frequencies
are output from other speakers).
you’re finished, press RETURN.
4 When
You return to the Manual SP Setup menu.
Note
• If you select SMALL for the front speakers, the subwoofer
will automatically be fixed to YES. Also, the center and
surround speakers can’t be set to LARGE if the front
speakers are set to SMALL. In this case, all bass
frequencies are sent to the subwoofer.
• If you have a subwoofer and like lots of bass, it may seem
logical to select LARGE for your front speakers and PLUS
for the subwoofer. This may not, however, yield the best
bass results. Depending on the speaker placement of your
room you may actually experience a decrease in the
amount of bass due to low frequency cancellations. In this
case, try changing the position or direction of speakers. If
you can’t get good results, listen to the bass response with
it set to PLUS and YES or the front speakers set to LARGE
and SMALL alternatively and let your ears judge which
sounds best. If you’re having problems, the easiest option
is to route all the bass sounds to the subwoofer by selecting
SMALL for the front speakers.
Home Menu
X.Over
• Default setting: 100Hz
This setting decides the cutoff between bass sounds playing
back from the speakers selected as LARGE, or the subwoofer,
and bass sounds playing back from those selected as SMALL.
It also decides where the cutoff will be for bass sounds in the
LFE channel.
• For more on selecting the speaker sizes, see Speaker Setting
on page 45.
1
2 Select ‘X.Over’ from the Manual SP Setup menu.
Select ‘Manual SP Setup’ from the Home Menu.
2b . X.Over
2 . Manual SP Setup
a.
b.
c.
d.
Frequency
Speaker Setting
X.Over
Channel Level
Speaker Distance
100Hz
2 Select ‘Channel Level’ from the Manual SP Setup menu. 4
2c . Channel Level
2 . Manual S P S etup
a.
b.
c.
d.
S peaker S etti ng
X . Over
Channel Level
S peaker Di stance
Test Tone
E NTE R:Next
Return
3
Manual
7
Return
Select a setup option.
• Manual – Move the test tone manually from speaker to
speaker and adjust individual channel levels.
• Auto – Adjust channel levels as the test tone moves
from speaker to speaker automatically.
your selected setup option.
4 Confirm
The test tones will start after you press ENTER. After the
Return
Return
the frequency cutoff point.
3 Choose
Frequencies below the cutoff point will be sent to the
subwoofer (or LARGE speakers).
you’re finished, press RETURN.
4 When
You return to the Manual SP Setup menu.
Channel Level
Using the channel level settings, you can adjust the overall
balance of your speaker system, an important factor when
setting up a home theater system.
CAUTION
volume increases to the reference level, test tones will be
output.
2c . Channel Level
Test Tone
[ Manual ]
Please Wait . . .20
Caution
Loud test tones
will be output.
Return
the level of each channel using /.
5 Adjust
If you selected Manual, use / to switch speakers. The
Auto setup will output test tones in the order shown onscreen:
2c . Channel Level
• The test tones used in the Channel Level settings are output
at high volume.
1 Select ‘Manual SP Setup’ from the Home Menu.
Front L
Center
Front R
S urround R
S urr. Back R
S urr. Back L
S urround L
S ubwoofer
[
[
[
[
[
[
[
0dB
0dB
0dB
0dB
–––
–––
0dB
0dB
]
]
]
]
]
]
]
Return
Adjust the level of each speaker as the test tone is
emitted.
46
56
7
Home Menu
Note
• If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
• The subwoofer test tone is output at low volumes. You may
need to adjust the level after testing with an actual
soundtrack.
you’re finished, press RETURN.
6 When
You return to the Manual SP Setup menu.
The Auto Power Down menu
Assigns input function for analog audio input terminal.
• For the assignment of the digital signal inputs, see
Selecting the audio input signal on page 23.
Set to automatically turn off the receiver after a specified time
has passed (when the power has been on with no operation
for several hours).
• Default setting: OFF
Analog Input
1 Select ‘Auto Power Down’ from the Home Menu.
ANALOG IN1 audio input terminal is assigned to CD under
factory settings, but this can be changed to TV input.
1
2 Select ‘Analog Input’ from the Input Assign menu.
Select ‘Input Assign’ from the Home Menu.
Tip
• You can change the channel levels at any time by press
RECEIVER , then press CH SELECT and LEV +/– on the
remote control. You can also press CH SELECT and use /
 to select the channel, and then use / to adjust the
channel levels.
Speaker Distance
3a . Analog Input
3 . Input Assign
Analog
a . Analog Input
b . Component Input
1 Select ‘Manual SP Setup’ from the Home Menu.
‘Speaker Distance’ from the Manual SP Setup
2 Select
menu.
2d . Speaker Dist ance
2 . M a nu a l S P S e t u p
S p e a k e r S e t t in g
X .O v e r
C h a n n e l L ev e l
S p e a k e r D is t a n c e
Front L
Cent er
Front R
Surround R
Surr. Back R
Surr. Back L
Surround L
Subwoofer
[
[
[
[
[
[
[
R e t u rn
3 m
3 m
3 m
3 m
––––
––––
3 m
3 m
]
]
]
]
]
]
]
Home Menu
1 . Auto MCACC
2 . Manual S P S etup
3 . I nput Assi gn
4. Auto Power Down
5. HDMI S etup
6. Network S tandby
7. MHL S etup
8. OS D S etup
4 . Auto Power Down
Auto Power Down
CD
OFF
Return
the amount of time to allow before the power
2 Specify
is turned off (when there has been no operation).
Return
For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
a.
b.
c.
d.
The Input Assign menu
Return
the desired input option for the ANALOG IN1
3 Select
audio input terminal.
you’re finished, press RETURN.
4 When
You return to the Input Assign menu.
Note
• When playing analog input audio, switch to the CD or TV
input menu, press RECEIVER and press SIGNAL SEL
several times to choose A (Analog). (see Selecting the audio
input signal on page 23)
• You can select 2, 4 or 6 hours, or OFF (if no automatic
shutoff is desired).
you’re finished, press RETURN.
3 When
You return to the Home Menu.
The Network Standby menu
This setting allows the AirPlay function for operating the
receiver from a computer connected on the same LAN as the
receiver to be used even when the receiver is in the standby
mode.
1 Select ‘Network Standby’ from the Home Menu.
Home Menu
1 . Auto MCACC
2 . Manual S P S etup
3 . I nput Assi gn
4. Auto Power Down
5. HDMI S etup
6. Network S tandby
7. MHL S etup
8. OS D S etup
Ret urn
the distance of each speaker using /.
3 Adjust
You can adjust the distance of each speaker in 0.03 m
6 . Network S tandby
Network S tandby
OFF
Return
increments.
ON or OFF for the Network Standby.
2 Choose
• ON – The AirPlay function can be used even when the
you’re finished, press RETURN.
4 When
You return to the Manual SP Setup menu.
receiver is in the standby mode.
47
4
7
56
7
Home Menu
• OFF – The AirPlay function cannot be used when the
receiver is in the standby mode (This lets you reduce
power consumption in the standby mode).
- If the Network Standby setting is set to ON, the
power consumption during standby will increase.
you’re finished, press RETURN.
3 When
You return to the Home Menu.
Select whether or not to switch the input automatically to the
MHL input when an MHL-compatible device is connected.
Note
• This is only valid for MHL-compatible devices supporting
this function.
1 Select ‘MHL Setup’ from the Home Menu.
H o me M e nu
1 . Au t o M C AC C
2 . M a nu a l S P S e t u p
3 . In p u t A s s ig n
4 . Au t o Pow e r D ow n
5. HDMI Setup
6 . N e t wo r k S t a n d by
7. MHL Setup
8. OSD Setup
Sets the overlay function ON/OFF.
1 Select ‘OSD Setup’ from the Home Menu.
Home Menu
The MHL Setup menu
7
9 . OSD Setup
1 . Auto MCACC
2 . Manual SP Setup
3 . Input Assign
4. Auto Power Down
5. HDMI Setup
6. Network Standby
7. MHL Setup
8. OSD Setup
OSD
ON
56
Return
2 Choose ON or OFF for the OSD Setup.
you’re finished, press RETURN.
3 When
You return to the Home Menu.
7 . M HL Set up
Aut o Swit ching
4
The OSD Setup menu
ON
Ret urn
2 Choose ON or OFF for the MHL Setup.
you’re finished, press RETURN.
3 When
You return to the Home Menu.
48
Chapter
8
Control with HDMI function
Synchronized operations below with a Control with HDMIcompatible Pioneer TV or Blu-ray Disc player are possible
when the component is connected to the receiver using an
HDMI cable.
• Synchronized amp mode
The receiver’s volume can be set and the sound can be
muted using the TV’s remote control.
• Power synchronization with TV
• Automatic switching of inputs
The receiver’s input switches over automatically when the
TV’s input is changed or a Control with HDMI-compatible
component is played.
Important
• With Pioneer devices, the Control with HDMI functions are
referred to as “KURO LINK”.
• You cannot use this function with components that do not
support Control with HDMI.
• We only guarantee this receiver will work with Pioneer
made Control with HDMI-compatible components.
However, we do not guarantee that all synchronized
operations will work with components that support the
Control with HDMI function.
• Use a High Speed HDMI®/™ Cable when you want to use
the Control with HDMI function. The Control with HDMI
function may not work properly if a different type of HDMI
cable is used.
• For details about concrete operations, settings, etc., refer to
also the operating instructions for each component.
Making Control with HDMI connections
You can use synchronized operation for a connected TV and
other components.
• Be sure to connect the TV’s audio cable to the audio input
of this unit. When the TV and receiver are connected by
HDMI connections, if the TV supports the HDMI Audio
Return Channel function, the sound of the TV is input to the
receiver via the HDMI terminal, so there is no need to
connect an audio cable. In this case, set ARC at HDMI
Setup to ON (see HDMI Setup below).
For details, see Connecting using HDMI on page 15.
Important
• When connecting this system or changing connections, be
sure to switch the power off and disconnect the power cord
from the wall socket.
After completing all connections, connect the power cords
to the wall socket.
• After this receiver is connected to an AC outlet, a 2 second
to 10 second HDMI initialization process begins. You
cannot carry out any operations during initialization. The
HDMI indicator on the display unit blinks during
initialization, and you can turn this receiver on once it has
stopped blinking.
• To get the most out of this function, we recommend that
you connect your HDMI component not to a TV but rather
directly to the HDMI terminal on this receiver.
HDMI Setup
You must adjust the settings of this receiver as well as the
connected Control with HDMI-compatible components in
order to make use of the Control with HDMI function. For
more information see the operating instructions for each
component.
on the receiver and your TV.
1 Switch
Press RECEIVER to switch on.
the TV input to the input that connects this
2 Switch
receiver to the TV through the corresponding HDMI
cable.
3 The Home Menu appears on your TV. Use /// and
Press RECEIVER , then press HOME MENU.
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
• Press HOME MENU at any time to exit the Home
Menu.
4
4 Select ‘HDMI Setup’ from the Home Menu.
Hom e Menu
1 . Auto MCACC
2 . Manual S P S etup
3 . I nput Assi gn
4. Auto Power Down
5. HDMI S etup
6. Network S tandby
7. MHL S etup
8. OS D S etup
5 . HDMI S etup
Control
[
ARC
S tandby Through [
OFF
OFF ]
OFF ]
Return
5
Select the ‘Control’ setting you want.
Choose whether to set this unit’s Control with HDMI
function ON or OFF. You will need to set it to ON to use
the Control with HDMI function.
When using a component that does not support the
Control with HDMI function, set this to OFF.
• ON – Enables the Control with HDMI function. When
this unit’s power is turned off and you have a
supported source begin playback while using the
Control with HDMI function, the audio and video
outputs from the HDMI connection are output from the
TV.
• OFF – The Control with HDMI is disabled.
Synchronized operations cannot be used. When this
unit’s power is turned off, audio and video of sources
connected via HDMI are not output.
- If the Control setting is not set to OFF, the power
consumption during standby will increase.
the ‘ARC’ setting you want.
6 Select
When a TV supporting the HDMI Audio Return Channel
function is connected to the receiver, the sound of the TV
can be input via the HDMI terminal.
• ON – The TV’s sound is input via the HDMI terminal.
This can only be selected when Control is set to ON.
• OFF – The TV’s sound is input from the audio input
terminals other than HDMI inputs.
- If the ARC setting is not set to OFF, the power
consumption during standby will increase.
the ‘Standby Through’ setting you want.
7 Choose
When the receiver is in standby, the HDMI input signal
selected here will be output to the TV by HDMI.
49
7
56
8
Control with HDMI function
• LAST – The HDMI input signal selected previously will
be output.
• BD, DVD, SAT/CBL, DVR/BDR, HDMI/MHL, GAME –
The HDMI input signal selected here will be output.
• OFF – Signal will not be output during standby
(However, when Control is set to ON, the HDMI signal
is transferred through by the Control with HDMI
function even when in the standby mode.).
- If the Standby Through setting is not set to OFF, the
power consumption during standby will increase.
- This setting can be used even with devices that are
not compatible with the Control with HDMI
function.
- The Standby Through function cannot be used with
MHL-compatible devices.
you’re finished, press RETURN.
8 When
You return to the Home Menu.
Before using synchronization
Once you have finished all connections and settings, you
must:
1 Put all components into standby mode.
the power on for all components, with the power
2 Turn
for the TV being turned on last.
the HDMI input to which the TV is connected to
3 Choose
this receiver, and see if video output from connected
components displays properly on the screen or not.
whether the components connected to all HDMI
4 Check
inputs are properly displayed.
About synchronized operations
The Control with HDMI-compatible component connected to
the receiver operates in sync as described below.
• Synchronized amp mode
- From the menu screen of the Control with HDMIcompatible TV, set audio to be played through this
receiver, and the receiver will switch to the synchronized
amp mode.
- When in the synchronized amp mode, the synchronized
amp mode is canceled when the receiver’s power is
turned off. To turn the synchronized amp mode back on,
set audio to be played through the receiver from the TV’s
menu screen, etc. This receiver will power up and switch
to the synchronized amp mode.
- When in the synchronized amp mode, the synchronized
amp mode is canceled if an operation that produces
sound from the TV is performed from the TV’s menu
screen, etc.
- When the synchronized amp mode is canceled, the
receiver’s power turns off if you were viewing an HDMI
input or a TV program on the TV.
• Power synchronization with TV
- When the TV’s power is set to standby, the receiver’s
power is also set to standby. (Only when the input for a
component connected to the receiver by HDMI
connection is selected or when watching the TV.)
• Automatic switching of inputs
- The receiver’s input switches automatically when the
Control with HDMI-compatible component is played.
- The receiver’s input switches automatically when the
TV’s input is switched.
- The synchronized amp mode remains in effect even if the
receiver’s input is switched to a component other than
one connected by HDMI.
Cautions on the Control with HDMI function
• Connect the TV and components (Blu-ray Disc player, etc.)
directly to this receiver. Interrupting a direct connection
with other amps or an AV converter (such as an HDMI
switch) can cause operational errors.
• When the receiver’s Control is turned ON, even if the
receiver’s power is in the standby mode, it is possible to
output the audio and video signals from a player via HDMI
to the TV without producing sound from the receiver, but
only when a Control with HDMI-compatible component
(Blu-ray Disc player, etc.) and compatible TV are
connected. In this case, the receiver’s power turns on and
the power and HDMI indicators light.
50
4
7
56
Chapter
9
Controlling the rest of your system
Setting the remote to control other
components
Most components can be assigned to one of the input
function buttons using the component’s manufacturer preset
code stored in the remote.
However, please note that there are cases where only certain
functions may be controllable after assigning the proper
preset code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
Note
• TV CONTROL buttons are only dedicated to control the TV
(for example, codes for TV, CATV, Satellite TV or DTV).
• You can cancel or exit any of the steps by pressing
RECEIVER .
• After one minute of inactivity, the remote automatically
exits the operation.
Selecting preset codes directly
Clearing all the remote control settings
You can clear all presets and restore the factory default
settings.
RECEIVER SLEEP
SOURCE
1
2
3
DISP
4
5
6
CH
7
8
9
CH
CLR
0
ENTER
RECEIVER
INPUT
SHIFT
RECEIVER
1
the input function button for the component you
2 Press
want to control.
While pressing RECEIVER , press and hold the ‘1’ button
for three seconds.
The component can be assigned to the BD, DVD, DVR/
BDR, SAT/CBL, GAME, CD, or TV button.
• When assigning preset codes to TV CONTROL, press
INPUT here.
the number buttons to enter the preset code.
3 Use
You can find the preset codes on page 52.
If the correct code has been input the power of the
component being input will turn on or off.
The power of the component being input will only turn on
or off if that component is able to be turned on directly by
remote control.
steps 2 through 3 to try a different code, or to
4 Repeat
enter a code for another component you want to
control.
5 When you’re done, press
RECEIVER .
51
4
pressing
 While
for three seconds.
7
Default preset codes
56
RECEIVER , press and hold the ‘0’ button
Input function
button
Preset code
BD
2 2 5 5
DVD
2 2 5 6
DVR/BDR
2 2 5 7
SAT/CBL
6 3 2 5
GAME
5 0 0 3
CD
5 0 0 0
TV
0 2 9 1
TV CONTROL
0 2 9 1
9
Controlling the rest of your system
Controls for TVs
Controls for other components
Preset Code List
This remote control can control components (TV, DTV,
Satellite TV or Cable TV) after entering the proper codes (see
Controlling the rest of your system on page 51 for more on
this). Use the input function buttons to select the component.
• The TV CONTROL buttons on the remote control are
dedicated to control the TV assigned to the TV CONTROL
INPUT button.
This remote control can control these components (BD, DVD,
CD, DVR (BDR), VCR, CD-R) after entering the proper codes
(see Controlling the rest of your system on page 51 for more on
this). Use the input function buttons to select the component.
For Blu-ray Disc player, DVD player, CD player, DVR (BDR), VCR,
CD-R:
You should have no problem controlling a component if you
find the manufacturer in this list, but please note that there
are cases where codes for the manufacturer in the list will not
work for the model that you are using. There are also cases
where only certain functions may be controllable after
assigning the proper preset code.
Button(s)
Function
Button(s)
SOURCE
Press to switch the component between
standby and on.

Press to return to the start of the current track.
Repeated presses skips to the start of previous
tracks.

Press to advance to the start of the next track.
Repeated presses skips to the start of following
tracks.
TV CONTROL  Switches the TV between standby and on.
TV CONTROL
INPUT
Switches the TV input. (Not possible with all
models.)
TV CONTROL CH Selects channels.
+/–
Important
Function
TV CONTROL
VOL +/–
Adjust the TV volume.
SOURCE
Press to switch the component assigned to the
TV button on or off.

Pause playback or recording.

Start playback.
HOME MENU
Use as the GUIDE button for navigating.

Hold down for fast forward playback.
RETURN
Use to select closed captioning with DTV.

Hold down for fast reverse playback.

Stops playback (on some models, pressing this
when the disc is already stopped will cause the
disc tray to open).
Number buttons Use to select a specific TV channel.
ENTER
Use to enter a channel.
MENU
Press to display the TV menu.
////
ENTER
Press to select or adjust and navigate items on
the menu screen.
CH +/–
Selects channels.
Number buttons Use to enter a title/chapter/track number.
DISP
Press to display information.
TOP MENU
Displays the disc ‘top’ menu of a BD/DVD
player.
MENU
Displays menus for the current BD/DVD or
DVR you are using.
////
Navigates BD/DVD menu/options.
ENTER/RETURN
HOME MENU
Displays the HOME MENU.
CH +/–
Selects channels. (DVR/VCR only)
52
• We do not guarantee the operations of all the
manufacturers and devices listed. Operation may not be
possible even if a preset code is entered.
example:
TV
Pioneer 0004
Category
Preset code
Manufacturer
4
7
56
9
TV
Pioneer 0004, 0006, 0113, 0233, 0252,
0275, 0291, 0305
Admiral 0001, 0014
Adventura 0012
Aiwa 0002
Akai 0002, 0100
Albatron 0097
Alleron 0009
America Action 0104
Amtron 0008
Anam 0104
Anam National 0003, 0008
AOC 0004, 0005, 0006, 0100
Apex 0021, 0102, 0106
Audiovox 0008, 0104
Aventura 0103
Axion 0094
Bang & Olufsen 0111
Belcor 0004
Bell & Howell 0001
Benq 0064
Bradford 0008, 0104
Brillian 0109
Brockwood 0004
Broksonic 0104
Candle 0004, 0006, 0012, 0100
Carnivale 0100
Carver 0101
CCE 0110
Celebrity 0002
Celera 0106
Changhong 0106
Citizen 0004, 0006, 0008, 0100
Clarion 0104
Coby 0056
Colortyme 0004, 0006
Concerto 0004, 0006
Contec 0104
Contec/Cony 0007, 0008
Craig 0008, 0104
Crosley 0081, 0101
Crown 0008, 0104
CTX 0063
Curtis Mathes 0000, 0004, 0006,
0014, 0100, 0101
CXC 0008, 0104
Cytron 0093
Daewoo 0004, 0005, 0006, 0023
Daytron 0004 0006
Dell 0073
DiamondVision 0096
Dimensia 0000
Disney 0046
Dumont 0004, 0011, 0099
Durabrand 0041, 0103, 0104
Dwin 0014
Electroband 0002
Controlling the rest of your system
Electrograph 0107
Electrohome 0002, 0003, 0004, 0006
Element 0082
Emerson 0004, 0006, 0007, 0008,
0009, 0023, 0103, 0104
Emprex 0092
Envision 0004, 0006, 0100
Epson 0061
ESA 0103
Fujitsu 0009
Funai 0008, 0009, 0103, 0104
Futuretech 0008, 0104
Gateway 0067, 0107, 0108
GE 0000, 0003, 0004, 0006, 0010, 0016,
0039
GFM 0080, 0084
Gibralter 0004, 0011, 0099, 0100
Goldstar 0004, 0005, 0006, 0007, 0100
Gradiente 0066
Grunpy 0008, 0009, 0104
Haier 0112
Hallmark 0004, 0006
Harman/Kardon 0101
Harvard 0008, 0104
Havermy 0014
Hewlett Packard 0053
Hisense 0069
Hitachi 0004, 0006, 0007
Hyundai 0098
Ilo 0089, 0091
IMA 0008
Infinity 0101
InFocus 0074
Initial 0091
Insignia 0085, 0086
Inteq 0099
Janeil 0012
JBL 0101
JC Penney 0000, 0004, 0005, 0006,
0010
JCB 0002
Jensen 0004, 0006
JVC 0007, 0010, 0044
Kawasho 0002, 0004, 0006
KEC 0104
Kenwood 0004, 0006, 0100
KLH 0106
Kloss Novabeam 0008, 0012
KTV 0008, 0100, 0104, 0110
LG 0005, 0052, 0078, 0097
Logik 0001
Luxman 0004, 0006
LXI 0000, 0006, 0101, 0102
Magnavox 0004, 0006, 0019, 0020,
0037, 0042, 0100, 0101
Majestic 0001
Marantz 0004, 0006, 0062, 0100, 0101
Maxent 0087, 0107
Megapower 0097
Megatron 0006
Memorex 0001, 0005, 0006, 0041
MGA 0004, 0005, 0006, 0100
Midland 0010, 0011, 0099
Mintek 0091
Mitsubishi 0004, 0005, 0006, 0014,
0045
Monivision 0097
Montgomery Ward 0001
Motorola 0003, 0014
MTC 0004, 0005, 0006, 0100
Multitech 0008, 0104, 0110
NAD 0006, 0102
NEC 0003, 0004, 0005, 0006, 0100
Net-TV 0107
Nikko 0006, 0100
Norcent 0060
Olevia 0048, 0054, 0059
Onwa 0008, 0104
Oppo 0095
Optimus 0105
Optoma 0075
Optonica 0014
Orion 0025
Panasonic 0003, 0010, 0017, 0027,
0105, 0114
Penney 0100, 0102
Philco 0003, 0004, 0005, 0006, 0007,
0100, 0101
Philips 0003, 0004, 0007, 0019, 0020,
0101
Philips Magnavox 0019
Pilot 0004, 0100
Polaroid 0057, 0106
Portland 0004, 0005, 0006
Prima 0065
Princeton 0097
Prism 0010
Proscan 0000
Proton 0004, 0006, 0007
Protron 0055
Proview 0068
Pulsar 0004, 0011, 0099
Quasar 0003, 0010, 0105
Radio Shack 0100, 0104
Radio Shack/Realistic 0000, 0004,
0006, 0007, 0008
RCA 0000, 0003, 0004, 0005, 0006,
0013, 0024, 0035
Realistic 0100, 0104
Runco 0011, 0099, 0100
Sampo 0004, 0006, 0100, 0107
Samsung 0004, 0005, 0006, 0007,
0022, 0032, 0076, 0077, 0083, 0100,
0110
Sansui 0025
Sanyo 0004, 0050
Sceptre 0072
Scotch 0006
Scott 0004, 0006, 0007, 0008, 0009,
0090, 0104
Sears 0000, 0004, 0006, 0009, 0101,
0102, 0103
Sharp 0004, 0006, 0007, 0014, 0033
Sheng Chia 0014
Shogun 0004
Signature 0001
Sony 0002, 0018, 0029, 0030, 0031,
0034
Soundesign 0004, 0006, 0008, 0009,
0104
Squareview 0103
SSS 0004, 0008, 0104
Starlite 0008, 0104
Superscan 0014
Supre-Macy 0012
Supreme 0002
SVA 0088
Sylvania 0004, 0006, 0049, 0079,
0080, 0100, 0101, 0103
Symphonic 0008, 0041, 0103, 0104
Syntax 0054
Syntax-Brillian 0054
Tandy 0014
Tatung 0003, 0108
Technics 0010, 0105
Techwood 0004, 0006, 0010
Teknika 0001, 0004, 0005, 0006, 0007,
0008, 0009, 0101, 0104
TMK 0004, 0006
TNCi 0099
Toshiba 0026, 0028, 0036, 0038, 0040,
0043, 0102
Vector Research 0100
Vidikron 0101
Vidtech 0004, 0005, 0006
Viewsonic 0058, 0107
Viking 0012
Viore 0089
Vizio 0004, 0070, 0071, 0108
Wards 0000, 0001, 0004, 0005, 0006,
0009, 0100, 0101
Waycon 0102
Westinghouse 0047, 0051
White Westinghouse 0023
Yamaha 0004, 0005, 0006, 0100
Zenith 0001, 0004, 0011, 0015, 0099
DVD
If operations are not possible
using the preset codes below,
you may be able to conduct
operations with the preset codes
for the BD, DVR (BDR, HDR).
Pioneer 2014, 2197, 2256
53
Accurian 2092
Advent 2072
Aiwa 2012
Akai 2066
Alco 2070
Allegro 2087
Amphion MediaWorks 2037
AMW 2037
Apex 2002, 2018, 2079, 2080
Apple 2058
Arrgo 2088
Aspire 2073
Astar 2052
Audiovox 2070
Axion 2040
Bang & Olufsen 2081
Blaupunkt 2080
Blue Parade 2078
Boston 2059
Broksonic 2066
California Audio Labs 2068
CambridgeSoundWorks 2065
CineVision 2087
Coby 2029
Curtis Mathes 2089
CyberHome 2000, 2088
Cytron 2039
Daewoo 2021, 2087
Denon 2026, 2068
Desay 2055
DiamondVision 2042
Disney 2022
Durabrand 2090
Emerson 2067, 2082, 2091
Enterprise 2082
ESA 2053, 2091
Fisher 2083
Funai 2091
GE 2016, 2077, 2080
GFM 2043
Go Video 2087
Gradiente 2068
Greenhill 2080
Haier 2094
Harman/Kardon 2030, 2084
Hitachi 2011
Hiteker 2079
iLive 2062
Ilo 2038
Initial 2038, 2080
Insignia 2036, 2064, 2091
Integra 2078
iSymphony 2060
JBL 2084
JVC 2013
Kawasaki 2070
Kenwood 2028, 2068
KLH 2070, 2080
Koss 2024, 2069, 2075
Landel 2093
Lasonic 2085
Lenoxx 2074, 2090
LG 2019, 2051, 2061, 2082, 2087
Liquid Video 2075
Liteon 2025, 2092
Magnavox 2067, 2076, 2091
Memorex 2066
Microsoft 2077
Mintek 2038, 2080, 2086
Mitsubishi 2020
Nesa 2080
Next Base 2093
Nexxtech 2056
Onkyo 2076
Oppo 2041, 2057
Oritron 2069, 2075
Panasonic 2005, 2007, 2017, 2032,
2033, 2050, 2068, 2076
Philips 2045, 2076
Proceed 2079
Proscan 2077
Qwestar 2069
RCA 2008, 2016, 2070, 2077, 2078,
2080
Regent 2074
Rio 2087
Rowa 2071
Samsung 2009, 2011, 2015, 2031,
2044, 2068
Sansui 2066
Sanyo 2066, 2083
Sharp 2035
Sherwood 2063
Shinsonic 2086
Sonic Blue 2087
Sony 2003, 2004, 2010, 2012, 2027,
2046, 2047, 2048
Sungale 2054
Superscan 2067
Sylvania 2023, 2067, 2091
Symphonic 2023
Teac 2070
Technics 2068
Theta Digital 2078
Toshiba 2001, 2006, 2049, 2066, 2076
Trutech 2000
Urban Concepts 2076
US Logic 2086
Venturer 2070
Xbox 2077
Yamaha 2005, 2068
Zenith 2019, 2076, 2082, 2087
4
7
56
9
BD
If operations are not possible
using the preset codes below,
you may be able to conduct
operations with the preset codes
for the DVD, DVR (BDR, HDR).
Pioneer 2034, 2192, 2255, 2258, 2259,
2260, 2281
Denon 2310, 2311, 2312
Hitachi 2307, 2308, 2309
JVC 2290, 2291, 2293, 2294, 2295, 2296
LG 2286, 2287
Marantz 2302, 2303
Mitsubishi 2300, 2301
Onkyo 2289
Panasonic 2277, 2278, 2279,
Philips 2280
Samsung 2282
Sharp 2304, 2305, 2306
Sony 2283, 2284, 2285, 2292
Toshiba 2288, 2262
Yamaha 2297, 2298, 2299
DVR (BDR, HDR)
If operations are not possible
using the preset codes below,
you may be able to conduct
operations with the preset codes
for the DVD, BD.
Pioneer 2078, 2099, 2107, 2109, 2144,
2193, 2194, 2195, 2196, 2257, 2258,
2259, 2260, 2261, 2264, 2265, 2266,
2270
Panasonic 2263, 2269
Sharp 2267, 2275
Sony 2268, 2271, 2272, 2273, 2276
Toshiba 2274
VCR
Pioneer 1053, 1108
ABS 1017
Adventura 1005
Aiwa 1005
Alienware 1017
American High 1004
Asha 1002
Audio Dynamics 1000
Audiovox 1003
Bang & Olufsen 1032
Beaumark 1002
Bell & Howell 1001
Calix 1003
Candle 1002, 1003
Controlling the rest of your system
Canon 1004
Citizen 1002, 1003
Colortyme 1000
Craig 1002, 1003
Curtis Mathes 1000, 1002, 1004
Cybernex 1002
CyberPower 1017
Daewoo 1005
DBX 1000
Dell 1017
DIRECTV 1016, 1020, 1022, 1023,
1024, 1027, 1030, 1031
Dish Network 1029
Dishpro 1029
Durabrand 1018
Dynatech 1005
Echostar 1029
Electrohome 1003
Electrophonic 1003
Emerson 1003, 1004, 1005
Expressvu 1029
Fisher 1001
Fuji 1004
Funai 1005
Garrard 1005
Gateway 1017
GE 1002, 1004
GOI 1029
Goldstar 1000, 1003
Gradiente 1005
Harley Davidson 1005
Harman/Kardon 1000
Headquarter 1001
Hewlett Packard 1017
HNS 1016
Howard Computers 1017
HP 1017
HTS 1029
Hughes Network Systems 1016,
1020, 1022, 1023, 1024
Humax 1016, 1020
Hush 1017
iBUYPOWER 1017
Instant Replay 1004
JC Penney 1000, 1001, 1002, 1003,
1004
JCL 1004
JVC 1000, 1001, 1020, 1029
Kenwood 1000, 1001
Kodak 1003, 1004
LG 1003
Linksys 1017
Lloyd’s 1005
LXI 1003
Magnavox 1004, 1018
Magnin 1003
Marantz 1000, 1001, 1004
Marta 1003
Media Center PC 1017
MEI 1004
Memorex 1001, 1002, 1003, 1004,
1005, 1018, 1019
MGN Technology 1002
Microsoft 1017
Mind 1017
Mitsubishi 1010
Motorola 1004
MTC 1002
Multitech 1002, 1005
NEC 1000, 1001
Nikko 1003
Niveus Media 1017
Noblex 1002
Northgate 1017
Olympus 1004
Optimus 1003
Orion 1014, 1019
Panasonic 1004, 1008
Philco 1004
Philips 1004, 1011, 1016, 1020, 1022,
1023, 1024, 1025
Philips Magnavox 1011
Pilot 1003
Proscan 1030
Pulsar 1018
Quarter 1001
Quartz 1001
Quasar 1004
Radio Shack 1003
Radio Shack/Realistic 1001, 1002,
1003, 1004, 1005
Radix 1003
Randex 1003
RCA 1002, 1004, 1007, 1016, 1020,
1022, 1030, 1031
Realistic 1001, 1002, 1003, 1004, 1005
ReplayTV 1026
Ricavision 1017
Runco 1018
Samsung 1002, 1016, 1022, 1024
Sanky 1018
Sansui 1014, 1019
Sanyo 1001, 1002
Sears 1001, 1003, 1004
Sharp 1012
Shogun 1002
Singer 1004
Sonic Blue 1026
Sony 1006, 1009, 1017, 1021
Stack 1017
STS 1004
Sylvania 1004, 1005
Symphonic 1005
Systemax 1017
Tagar Systems 1017
Tandy 1001
Tashiko 1003
Teac 1005
Technics 1004
Teknika 1003, 1004, 1005
Tivo 1016, 1020, 1021, 1022, 1025
TMK 1002
Toshiba 1015, 1017, 1028
Totevision 1002, 1003
Touch 1017
UltimateTV 1031
Unitech 1002
Vector Research 1000
Video Concepts 1000
Videosonic 1002
Viewsonic 1017
Voodoo 1017
Wards 1002, 1003, 1004, 1005
XR-1000 1004, 1005
Yamaha 1000, 1001
Zenith 1013, 1018
ZT Group 1017
Satellite Set Top Box
Pioneer 6097, 6098, 6325, 6328, 6329
ADB 6035, 6001
Akai 6102
Alba 6005, 6011, 6013
Allsat 6102
Alltech 6011
Amstrad 6033, 6030, 6044
Anttron 6013
Asat 6102
Austar 6000, 6045
Bell ExpressVu 6002, 6003
British Sky Broadcasting 6030
Canal 6105
Chaparral 6034
CNS 6001
Coolsat 6021
Crossdigital 6043
Digenius 6104
Digiwave 6053
DirecTV 6070, 6110, 6111, 6062, 6063,
6113, 6008, 6038, 6054, 6069, 6060,
6059, 6043, 6018, 6114, 6115, 6116,
6093
Dish Network System 6002, 6089,
6003, 6004
Dishpro 6002, 6089, 6004
Echostar 6002, 6089, 6036, 6005,
6003, 6004
Expressvu 6002, 6004
Fortec Star 6123, 6023
Fresat 6014
Funai 6070
GE 6111
General Instrument 6032
54
GOI 6002, 6004
Grundig 6007, 6030
Hirschmann 6033
Hisense 6020
Hitachi 6038, 6049
Houston 6002
HTS 6002, 6004
Hughes Network Systems 6113,
6038, 6054, 6114, 6115, 6116
Hyundai 6016
iLo 6020
Innova 6059
Jerrold 6032
JVC 6002, 6003, 6004
Kathrein 6096
Lava 6053
LG 6047, 6018
Marantz 6102
McIntosh 6032
Mitsubishi 6038
Motorola 6032, 6042
NEC 6050
Netsat 6059
Next Level 6032
nfusion 6015
Nokia 6025, 6026, 6118, 6119, 6121
Pace 6035, 6005, 6030, 6031
Panarex 6016
Panasonic 6008, 6009, 6030
Pansat 6016, 6022
Philips 6002, 6113, 6038, 6054, 6060,
6059, 6102, 6103, 6030, 6114
Primestar 6032
Proscan 6110, 6111
Proton 6020
RadioShack 6002, 6111, 6032
Radix 6036
RCA 6002, 6110, 6111, 6113, 6109,
6061, 6114
Saba 6014
Sagem 6041, 6120
Samsung 6070, 6113, 6091, 6043,
6017, 6114, 6093
Sanyo 6046
Sat Cruiser 6015
Schwaiger 6066
Siemens 6007, 6036
SKY 6042, 6059, 6030, 6031
SM Electronic 6011
Smart 6051
Sonicview 6055, 6107
Sony 6062, 6063, 6030
Star Choice 6032
Star Trak 6032
TechniSat 6033
Thomson 6110, 6111, 6014
Tivo 6113, 6114, 6115, 6116
Toshiba 6038, 6054, 6039
TPS 6041
Triasat 6033
Ultrasat 6021
US Digital 6020
USDTV 6020
ViewSat 6048
Voom 6032
Zehnder 6101
Zenith 6042, 6069, 6037
Satellite Set Top Box
(SAT/PVR Combination)
Bell ExpressVu 6002, 6003
DirecTV 6070, 6110, 6062, 6113, 6060,
6059, 6114, 6115, 6116
Dish Network System 6002, 6089
Dishpro 6002, 6089
Echostar 6002, 6089, 6003
Expressvu 6002
Hughes Network Systems 6113,
6114, 6115, 6116
JVC 6003
Motorola 6032
Philips 6113, 6114
Proscan 6110
Samsung 6114
Sonicview 6055, 6107
Sony 6062
Star Choice 6032
Tivo 6113, 6114, 6115, 6116
Cable Set Top Box
Pioneer 0297, 6028, 6029, 6095, 6099,
6325, 6328, 6329
ABC 6122
Accuphase 6122
Amino 6077, 6078
Auna 6082
BCC 6072
Bell & Howell 6122
Bright House 6074, 6029
Cable One 6074, 6029
Cablevision 6074, 6029
Charter 6074, 6029, 6058
Cisco 6029, 6028, 6083
Comcast 6074, 6029, 1982
Cox 6074, 6029
Digeo 6029, 6058
Director 6073
Emerson 6122
Fosgate 6072
General Instrument 6073, 6072,
6122
Homecast 6024
4
7
56
9
Controlling the rest of your system
i3 Micro 6077
Insight 6074, 6073, 6029
Jebsee 6122
Jerrold 6073, 6072, 6122
Knology 6029
Macab 6040
Mediacom 6074, 6029
Memorex 6112
Motorola 6074, 6073, 6072, 6029,
6122, 6094
MTS 6094
Myrio 6077, 6078
Noos 6040
Pace 6074, 6029, 6028, 6106, 6083
Panasonic 6112, 6083
Paragon 6112
Penney 6112
Philips 6012
Pulsar 6112
Quasar 6112
Regal 6072
Rogers 6029
Runco 6112
Samsung 6095
Scientific Atlanta 6029, 6028, 6027,
6112
Sejin 6077
Shaw 6074
Starcom 6122
Stargate 6122
Suddenlink 6074, 6029
Supercable 6072
Time Warner 6074, 6029, 6058
Tivo 6076
Toshiba 6112
United Cable 6072, 6122
US Electronics 6072
Videoway 6112
Zenith 6112
Insight 6074, 6029
Knology 6029
Mediacom 6074, 6029
Motorola 6074, 6081
Myrio 6078
Pace 6029
Panasonic 6083
Rogers 6029
Scientific Atlanta 6029
Shaw 6074
Suddenlink 6074, 6029
Supercable 6072
Time Warner 6074, 6029, 6058
Tivo 6076
Cable Set Top Box (Cable/
PVR Combination)
Pioneer 5001, 5053, 5071
Philips 5054
Yamaha 5055
Pioneer 6029, 6325, 6328, 6329
Amino 6078
Bright House 6074, 6029
Cable One 6074, 6029
Cablevision 6074, 6029
Charter 6074, 6029, 6058
Cisco 6029, 6083
Comcast 6074, 6029, 6083, 6076
Cox 6074, 6029
Digeo 6081, 6058
Homecast 6024
CD
Pioneer 5000, 5011, 5070
AKAI 5043
Asuka 5045
Denon 5019
Fisher 5048
Goldstar 5040
Hitachi 5042
Kenwood 5020, 5021, 5031
Luxman 5049
Marantz 5033
Onkyo 5017, 5018, 5030, 5050
Panasonic 5036
Philips 5022, 5032, 5044
RCA 5013, 5029
Roadstar 5052
Sharp 5051
Sony 5012, 5023, 5026, 5027, 5028,
5039
TEAC 5015, 5016, 5034, 5035, 5037
Technics 5041
Victor 5014
Yamaha 5024, 5025, 5038, 5046, 5047
4
Digital Tape
Pioneer 5057
MD
7
Pioneer 5056
Network Audio Player
56
Pioneer 5063
Game
X-Box 2313
AV Receiver
Pioneer 5062
CD-R
Tuner
Pioneer 5060
Laser Disc Player
Pioneer 5002, 5003
Casette Deck
Pioneer 5058, 5059
55
Chapter
10
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Take a look at the
other components and electrical appliances being used,
because sometimes the problem may lie there. If the trouble
isn’t sorted out even after going through the checks below,
ask your nearest Pioneer authorized independent service
company to carry out repair work.
• If the unit does not operate normally due to external effects
such as static electricity disconnect the power plug from
the outlet and insert again to return to normal operating
conditions.
General
 The power does not turn on.
 Disconnect the power plug from the outlet, and insert again.
 Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
 The receiver suddenly switches off.
 When the Auto Power Down function is working, the power will
automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 47).
 After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
 If there is very little low frequency information in the source
material, change your speaker settings to Front: SMALL /
Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (page 45).
 The HDMI indicator blinks and the power does not turn
on.
 The receiver may have a serious problem. Do not try switching
the receiver on. Unplug the receiver from the wall and call a
Pioneer authorized independent service company.
 The power suddenly turns on or off, or the input suddenly
changes (When the Control with HDMI is ON).
 This happens because of the synchronized operation due to
the Control with HDMI function. If synchronized operations
are not needed, set the Control with HDMI to OFF (see HDMI
Setup on page 49).
 OVERHEAT shows in the display and the power turns off.
 The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
 Lower the volume level.
 TEMP shows in the display and the volume level drops.
 The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
 Lower the volume level.
 No sound is output when an input function is selected.
 Use VOLUME +/– to turn up the volume.
 Press MUTE on the remote control to turn muting off.
 Press SPEAKERS to select the proper speaker set (see
Switching the speaker terminal on page 13).
 Set the SIGNAL SEL to H (HDMI), C1/O1 (digital) or A (analog)
according to the type of connections made (page 23).
 Make sure the component is connected correctly (refer to
Connecting your equipment on page 11).
 Check the audio output settings of the source component.
 Refer to the instruction manual supplied with the source
component.
 No image is output when an input function is selected.
 Make sure the component is connected correctly (refer to
Connecting your equipment on page 11).
 Use the same type of video cables for the source component
and TV to connect to this receiver (see About video outputs
connection on page 14).
 The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
 No sound from subwoofer.
 Make sure the subwoofer is switched on.
 If the subwoofer has a volume knob, make sure it’s turned up.
 The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
 Switch the subwoofer setting in Speaker Setting on page 45 to
YES or PLUS.
 Switch the LFE ATT (LFE Attenuate) on page 34 to LFEATT 0 or
LFEATT 5.
 No sound from surround or center speakers.
 Connect the speakers properly (page 12).
 Refer to Speaker Setting on page 45 to check the speaker
settings.
 Refer to Channel Level on page 46 to check the speaker levels.
56
 The OSD screen (Home Menu, etc.) isn’t displayed.
 The OSD will not appear if you have connected using the
composite output to your TV. Use HDMI connection when
setting up the system.
 The Phase Control feature doesn’t seem to have an
audible effect.
 If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
 Make sure the speaker distance setting is correct for all
speakers (see Speaker Distance on page 47).
 Considerable noise in radio broadcasts.
 Connect the antenna (page 18) and adjust the position for best
reception.
 Route any loose cables away from the antenna terminals and
wires.
 Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
 Connect an additional internal or external AM antenna
(page 18).
 Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
 Broadcast stations cannot be selected automatically.
 Connect an outdoor antenna (page 18).
 Noise during playback of a cassette deck.
 Move the cassette deck away from your receiver, until the noise
disappears.
 No sound is output or a noise is output when software
with DTS is played back.
 Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
 There seems to be a time lag between the speakers and
the output of the subwoofer.
 See Automatically setting up for surround sound (MCACC) on
page 21 to set up your system again using MCACC (this will
automatically compensate for a delay in the subwoofer output).
 After using the Auto MCACC setup, the speaker size
setting (LARGE or SMALL) is incorrect.
 Low-frequency noise could have been caused by an air
conditioner or motor. Switch off all appliances in the room and
rerun the Auto MCACC setup.
4
7
56
10
 Can’t operate the remote control.
 Replace the batteries (page 10).
 Operate within 7 m, 30º of the remote sensor (page 10).
 Remove the obstacle or operate from another position.
 Avoid exposing the remote sensor on the front panel to direct
light.
 Press the remote control’s RECEIVER button and switch to
receiver control mode.
 The display is dark.
 Press DIMMER on the remote control repeatedly to return to
the default.
 During ECO mode, the brightness switches between 2 levels. If
the dimmest level is selected, DIMMER will be shown on the
display. (Mode other than ECO: 4 levels, ECO mode: 2 levels)
 The receiver doesn’t recognize iPod touch/iPhone/iPad.
 Try the following.
 1. Simultaneously keep pressing the sleep button and home
button on the iPod touch or iPhone for over 10 seconds to
restart.
 2. Turn on the receiver.
 3. Connect the iPod touch/iPhone to the receiver.
 The Bluetooth wireless technology device cannot be
connected or operated. Sound from the Bluetooth
wireless technology device is not emitted or the sound is
interrupted.
 Check that no object that emits electromagnetic waves in the
2.4 GHz band (microwave oven, wireless LAN device or
Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop
using the object emitting the electromagnetic waves.
 Check that the Bluetooth wireless technology device is not too
far from the unit and that obstructions are not set between the
Bluetooth wireless technology device and the unit. Set the
Bluetooth wireless technology device and the unit so that the
distance between them is less than about 10 m and no
obstructions exist between them.
 Check that the Bluetooth ADAPTER and the ADAPTER PORT
terminal of the unit are correctly connected.
 The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless
technology. Check the setting of the Bluetooth wireless
technology device.
 Check that pairing is correct. The pairing setting was deleted
from this unit or the Bluetooth wireless technology device.
Reset the pairing.
Additional information
 Check that the profile is correct. Use a Bluetooth wireless
technology device that supports A2DP profile and AVRCP
profile.
 The Air Jam function cannot be used.
 An iPod is connected to this receiver. Disconnect the iPod from
this receiver (page 29).
 Display flashes and cannot be operated.
 Depending on the input signal or listening mode, there may be
functions that cannot be selected.
NETWORK feature
 Cannot access the network.
 The LAN cable is not firmly connected. Firmly connect the LAN
cable (page 17).
 The router is not switched on. Switch on the router.
 Internet security software is currently installed in the
connected component. There are cases where a component
with Internet security software installed cannot be accessed.
 The audio component on the network which has been
switched off is switched on. Switch on the audio component
on the network before switching on this receiver.
 Playback does not start while ‘Connecting Wired...’
continues to be displayed.
 The component is currently disconnected from this receiver or
the power supply. Check whether the component is properly
connected to this receiver or the power supply.
 The PC or Internet radio is not properly operated.
 The corresponding IP address is not properly set. Switch on the
built-in DHCP server function of your router, or set up the
network manually according to your network environment
(page 47).
 The IP address is being automatically configured. The
automatic configuration process takes time. Please wait.
 The audio files stored on components on the network,
such as a PC, cannot be played back.
 Windows Media Player 11 or Windows Media Player 12 is not
currently installed on your PC. Install Windows Media Player 11
or Windows Media Player 12 on your PC.
 Audio files recorded in MPEG-4 AAC or FLAC are being played
back on Windows Media Player 11 or Windows Media Player
12. Audio files recorded in MPEG-4 AAC or FLAC cannot be
played back on Windows Media Player 11 or Windows Media
Player 12. Try using another server. Refer to the operation
manual supplied with your server.
 The component connected to the network is not properly
operated.
57
- Check whether the component is affected by special
circumstances or is in the sleep mode.
- Try rebooting the component if necessary.
 The component connected to the network does not permit file
sharing. Try changing the settings for the component
connected to the network.
 The folder stored on the component connected to the network
has been deleted or damaged. Check the folder stored on the
component connected to the network.
 Network connections could be restricted due to the
computer’s network settings, security settings, etc. Check the
computer’s network settings, security settings, etc.
 The audio files are copyrighted. DRM-protected audio files
cannot be played back on this receiver.
 Cannot access the component connected to the network.
 The component connected to the network is not properly set. If
the client is automatically authorized, you need to enter the
corresponding information again. Check whether the
connection status is set to “Do not authorize”.
 There are no playable audio files on the component connected
to the network. Check the audio files stored on the component
connected to the network.
 Audio playback is undesirably stopped or disturbed.
 The audio file currently being played back was not recorded in
a format playable on this receiver.
- Check whether the audio file was recorded in a format
supported by this receiver.
- Check whether the folder has been damaged or corrupted.
- Note that there are cases where even the audio files listed as
playable on this receiver cannot be played back or displayed
(page 44).
 The LAN cable is currently disconnected. Connect the LAN
cable properly (page 17).
 There is heavy traffic on the network with the Internet being
accessed on the same network. Use 100BASE-TX to access the
components on the network.
 When in the DMR mode, depending on the external controller
being used, playback may be interrupted when a volume
operation is performed from the controller. In this case, adjust
the volume from the receiver or remote control.
4
7
56
10
 Cannot access Windows Media Player 11 or Windows
Media Player 12.
 In case of Windows Media Player 11: You are currently logged
onto the domain through your Computer with Windows XP or
Windows Vista installed. Instead of logging onto the domain,
log onto the local machine (page 37).
 In case of Windows Media Player 12: You are currently logged
onto the domain through your Computer with Windows 7
installed. Instead of logging onto the domain, log onto the local
machine (page 37).
 Cannot listen to Internet radio stations.
 The firewall settings for components on the network are
currently in operation. Check the firewall settings for
components on the network.
 You are currently disconnected from the Internet. Check the
connection settings for components on the network, and
consult with your network service provider if necessary
(page 39).
 The broadcasts from an Internet radio station are stopped or
interrupted. There are cases where you cannot listen to some
Internet radio stations even when they are listed in the list of
Internet radio stations on this receiver (page 38).
 The NETWORK function cannot be operated with the
buttons on the remote control.
 The remote control is not currently set to the NETWORK mode.
Press NETWORK to set the remote control to the NETWORK
mode (page 42).
HDMI
 No picture or sound.
 If the problem still persists when connecting your HDMI
component directly to your monitor, please consult the
component or monitor manual or contact the manufacturer for
support.
 No picture.
 Video signals that are input from the analog video terminal will
not output from the HDMI terminal. Signals that are input from
the HDMI terminal will not output from the analog video
terminal. Be consistent with the type of cable between input
and output.
 Depending in the output settings of the source component, it
may be outputting a video format that can’t be displayed.
Change the output settings of the source, or connect using the
composite video jacks.
Additional information
 This receiver is HDCP-compatible. Check that the components
you are connecting are also HDCP-compatible. If they are not,
please connect them using the composite video jacks.
 Depending on the connected source component, it’s possible
that it will not work with this receiver (even if it is HDCPcompatible). In this case, connect using the composite video
jacks between source and receiver.
 If video images do not appear on your TV, try adjusting the
resolution, Deep Color or other setting for your component.
 To output signals in Deep Color, use an HDMI cable (High
Speed HDMI®/™ Cable) to connect this receiver to a
component or TV with the Deep Color feature.
 No sound, or sound suddenly ceases.
 Check that the HDMI setting is set to AMP (page 34).
 If the component is a DVI device, use a separate connection for
the audio.
 HDMI format digital audio transmissions require a longer time
to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning
playback.
 Turning on/off the device connected to this unit’s HDMI OUT
terminal during playback, or disconnecting/connecting the
HDMI cable during playback, may cause noise or interrupted
audio.
 Synchronized operation not possible using Control with
HDMI function.
 Check the HDMI connections.
 The cable may be damaged.
 Select ON for the Control with HDMI setting (see HDMI Setup
on page 49).
 Turn the TV’s power on before turning on this receiver’s power.
 Set the TV side Control with HDMI setting to on (see TV’s
operating instructions).
Important information regarding the HDMI
connection
There are cases where you may not be able to route HDMI
signals through this receiver (this depends on the HDMI
equipped component you are connecting-check with the
manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly through this
receiver (from your component), please try the following
configuration when connecting up.
58
Configuration
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most convenient
connection (digital is recommended) for sending audio to the
receiver. See the operating instructions for more on audio
connections. Set the display volume to minimum when using
this configuration.
Note
• Depending on the component, audio output may be limited
to the number of channels available from the connected
display unit (for example audio output is reduced to 2
channels for a monitor with stereo audio limitations).
• If you want to switch the input source, you’ll have to switch
functions on both the receiver and your display unit.
• Since the sound is muted on the display when using the
HDMI connection, you must adjust the volume on the
display every time you switch input sources.
Windows 7
Windows and the Windows logo are trademarks of the Microsoft
group of companies.
MHL
MHL, the MHL Logo, and Mobile High-Definition Link are
trademarks or registered trademarks of MHL, LLC in the United
States and other countries.
This receiver incorporates MHL 2.
4
7
56
10
HTC Connect
HTC, HTC Connect and the HTC Connect logo are trademarks
of HTC Corporation.
About iPod/iPhone/iPad
Additional information
USB works with iPhone 5, iPhone 4S, iPhone 4, iPhone 3GS,
iPhone 3G, iPhone, iPad (3rd and 4th generation), iPad 2,
iPad, iPad mini, iPod touch (1st through 5th generation) and
iPod nano (3rd through 7th generation).
“Made for iPod,” “Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this
accessory with iPod, iPhone, or iPad may affect wireless
performance.
Apple, AirPlay, iPad, iPhone, iPod, iPod nano, iPod touch,
iTunes, Safari, Bonjour and Mac are trademarks of Apple Inc.,
registered in the U.S. and other countries. The AirPlay logo is a
trademark of Apple Inc.
Apple Lossless Audio Codec
Copyright © 2011 Apple Inc. All rights reserved.
Licensed under the Apache License, Version 2.0. You may
obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS
AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
About messages displayed when using
network functions
Refer to the following information when you come up with a
status message while operating the Network functions.
Status messages
Descriptions
Connection Down
The selected category or Internet radio
station cannot be accessed.
File Format Error
Cannot be played back for some
reasons.
Track Not Found
The selected song has not been found
anywhere on the network.
Server Error
The selected server cannot be accessed.
About FLAC
FLAC Decoder
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion, and Mac and PC
with iTunes 10.2.2 or later.
Bluetooth technology works with iPhone 5, iPhone 4S, iPhone
4, iPhone 3GS, iPhone 3G, iPhone, iPad (3rd and 4th
generation), iPad 2, iPad, iPad mini, and iPod touch (2nd
through 5th generation).
Copyright © 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007,
2008, 2009 Josh Coalson
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
• Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
• Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
• Neither the name of the Xiph.org Foundation nor the
names of its contributors may be used to endorse or
promote products derived from this software without
specific prior written permission.
59
Server Disconnected The server has been disconnected.
Empty
There are no files stored in the selected
folder.
License Error
The license for the contents to be played
back is invalid.
Item Already Exists
This is displayed when the file you have
attempted to register in the Favorites
folder has already been registered.
4
7
56
10
Additional information
Status messages
Descriptions
Favorite List Full
This is displayed when you have
attempted to register a file in the
Favorites folder but the Favorites folder is
already full.
• Never use thinners, benzine, insecticide sprays or other
chemicals on or near this unit, since these will corrode the
surface.
Resetting the main unit
Use this procedure to reset all the receiver’s settings to the
factory default. Use the front panel controls to do this.
• For instructions on resetting the network connection
settings, see Factory Reset on page 42.
1 Switch the receiver into standby.
holding down BAND, press and hold
2 While
STANDBY/ON for about two seconds.
you see RESET? appear in the display, press
3 When
AUTO SURROUND/STREAM DIRECT.
OK? shows in the display.
ALC/STANDARD SURR to confirm.
4 Press
OK appears in the display to indicate that the receiver
Manufactured under license from Dolby Laboratories. Dolby,
Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent Nos: 5,956,674;
5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending. DTS-HD, the Symbol, & DTS-HD and the
Symbol together are registered trademarks of DTS, Inc. Product
includes software. © DTS, Inc. All Rights Reserved.
has been reset to the factory default settings.
Important
• If the Control with HDMI function is set to ON, the HDMI
function’s Standby Through is set to anything other than
OFF, or the Network Standby is set to ON, you may not be
able to reset the unit. In this case, reset either by turning
OFF the Control with HDMI function, or by putting the unit
into standby mode by turning off the power of all the
connected devices, and resetting after the HDMI indicator
on the front panel turns off.
Specifications
Audio Section
FTC power output . . . . . . . . . . . . . . . . . . . . . . . . . 65 W + 65 W
(STEREO, 20 Hz to 20 kHz, 8 , 0.2 %)
Rated power output (Front, Center, Surround)
. . . . . . . . . . . . . . . . . . . . . 125 W per channel (1 kHz, 6 , 1 %)
Maximum power output (Front, Center, Surround)
. . . . . . . . . . . . . . . . . . . . 150 W per channel (1 kHz, 6 , 10 %)
Total Harmonic Distortion
. . . . . . . . . . . . . . . . . . . 0.06 % (20 Hz to 20 kHz, 8 , 50 W/ch)
Guaranteed speaker impedance . . . . . . . . . . . . . . .6  to 16 
Input (Sensitivity/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 k
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB
Video Section
Signal level
Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 )
Tuner Section
Frequency Range (FM) . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Antenna Input (FM) . . . . . . . . . . . . . . . . . . . .75  unbalanced
Frequency Range (AM)
9 kHz step . . . . . . . . . . . . . . . . . . . . . . . 531 kHz to 1602 kHz
10 kHz step . . . . . . . . . . . . . . . . . . . . . . 530 kHz to 1700 kHz
Antenna (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . .Loop antenna
Digital In/Out Section
HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . .Type A (19-pin)
HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 100 mA
HDMI input/MHL terminal . . . . . . . . . . . . . . . . . . . 5 V, 900 mA
USB terminal. . . . . . . .USB2.0 High Speed (Type A) 5 V, 2.1 A
iPod terminal. . . . . . . . . . . . . . . . USB, and Video (Composite)
ADAPTER PORT terminal . . . . . . . . . . . . . . . . . . . 5 V, 100 mA
Cleaning the unit
Network Section
• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• When the surface is dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six times with water,
and wrung out well, and then wipe again with a dry cloth.
Do not use furniture wax or cleansers.
LAN terminal . . . . . . . . . . . . . . . . . . . . 10 BASE-T/100 BASE-TX
60
4
7
56
10
Additional information
4
Miscellaneous
Power Requirements
. . . . . . . . . . . . . AC 110 V to 127 V/220 V to 240 V, 50 Hz/60 Hz
Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 W
In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.1 W
Weight (without package) . . . . . . . . . . . . . . . . . . . . . . . . 8.5 kg
Furnished Parts
Microphone (for Auto MCACC setup) . . . . . . . . . . . . . . . . . .
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dry cell batteries (AAA size IEC R03) . . . . . . . . . . . . . . . . . . .
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FM wire antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick start guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Brochure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPEAKER CAUTION Sheet (English only) . . . . . . . . . . . . . . .
Power cord
These operating instructions (CD-ROM)
7
56
1
1
2
1
1
1
1
1
Note
• The specifications are applicable when the power supply is
230 V.
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
• This product includes FontAvenue® fonts licensed by NEC
Corporation. FontAvenue is a registered trademark of NEC
Corporation.
• Microsoft, Windows, Windows Media and Windows Vista
are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
61
© 2013 PIONEER CORPORATION.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En
<ARB7523-A>