SSA-S1000
Standalone RFID
Access Controller
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please visit our website.
www.samsungsecurity.com
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is
present within this unit.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to
the product.
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the
controller. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the
power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)
10.. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive
vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -20°C), or high humidity.
Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or damage
to the product.
2_ Safety information
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
FCC Statement
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause undesired operation.
Caution
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
English3
PRODUCT
SAFETY
INFORMATION
INTRODUCTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
contents
PRODUCT INTRODUCTION
5
INSTALLATION AND EXTERNAL
CONNECTION
9
SYSTEM INITIALIZATION & BASIC
OPERATIONS
12
PRODUCT SPECIFICATIONS
15
5
6
7
8
8
Feature
What’s included
At a Glance
Cable Color Scheme
Cable Selection
9
9
10
Installation
Bypass Diode Connection
I/O Connection
12
12
13
13
Initializing the system by short-circuiting
Basic Operations
To register /delete Master ID
To register/delete ID card
15
Product Specifications
product introduction
FEATURE
◆ 125 kHz Proximity Access Controller
◆ Up to 512 users including one Master ID can be registered
◆ Standalone (no application S/W required)
◆ Direct Control of the Door Lock
◆ Can select a lock device type from Power Fail Safe and Power Fail Secure
◆ Epoxy Molding
◆ Weatherproof
English5
PRODUCT INTRODUCTION
This product is designed for use with one-door access control for security applications. With its compact design, you can
install this product on the wall or a doorframe; Its epoxy molding guarantees stable operation in a challenging environment.
This product enables you to control the door using the user card and provides a simple method to register or delete cards,
and initialize the system, which is, one of the most convenient and safest door controller.
And it is also featured by the 2-color LED indicator and the internal buzzer, enabling you to easily check the current mode
and operation of the door lock.
product introduction
WHAT’S INCLUDED
Check if the following items are included in the product package.
tˆš›Œ™Gjˆ™‹
Main Module
Bezel
Master Card (x1)
Keytag (x5)
xœŠ’Gnœ‹Œ
3.5 x 40mm Screws (x2)
3.5 x 25mm Screws (x2)
6 x 30mm Plastic Anchors (x2)
CD Manual
6_ Product Introduction
Diode (X 2)
(UF4004, 1N4001~4007)
Quick Guide
AT A GLANCE
Front/Rear
PRODUCT INTRODUCTION
3
4
5
1
LED
Displays the system operation status using red and green indicators.
2
Fixing Hole
Fixing hole for wall-mounting.
3
Connection Cable
Used to connect to the power or I/O cable.
4
Program Port
Port used to upgrade the firmware.
5
Buzzer
Piezo buzzer.
English7
product introduction
CABLE COLOR SCHEME
Item
Cable Color
Signal Line
Description
Red
DC+12V
Black
GND
Yellow
AUX INPUT#1
Blue
Door Contact Sensor
Green
Exit Button
Exit Button Connection Port
Purple
Alarm Out
Alarm Device Connection
Port
White
Door Lock Out
+12V supplied
Power
Input
Earth-Grounding for Power
Select a Lock Type
Door Sensor Connection Port
Output
Gray
Orange
Not used
Brown
CABLE SELECTION
Item
1
2
Power (DC +12V)
Belden #9409, 18 AWG 2 Conductor, Unshielded
Door Contact Sensor
Belden #9512, 22 AWG 4 Conductor, Shielded
Exit Button
Sensor Input
3
Cable Type
Door Lock
Alarm Device
8_ Product Introduction
Belden #9514, 22 AWG 8 Conductor, Shielded
Belden #9409, 18AWG 2 Conductor, Unshielded
Door Lock device connection
port
installation and external connection
INSTALLATION
INSTALLATION AND EXTERNAL CONNECTION
10
6-32 hole
44.4
6-32 or M3 Screws
1/2” hole
40.6
6-32 hole
Reader
Module
8.5
- On a doorframe or the wall
1. Drill a 1/2-inch (12.7 mm) hole onto the center of the doorframe or the wall where SSA-S1000 is installed, which
makes room for the cable of the reader module.
2. Drill two 0.3-inch (7.62 mm) holes: one on the point of 0.39 inch (10 mm) horizontally to the right, 1.74 inch
(44.4 mm) vertically up from the center hole, and one on the point of 0.33 inch (8.5 mm) horizontally to the left,
0.3 inch (7.62 mm) vertically down from the point.
3. Insert the reader module cable into the center hole and secure the module using two screws inserted in the
upper right and the bottom left corner, respectively.
4. Insert the bezel of SSA-S1000 into the reader module and attach it by pressing the upper and lower corner of
the bezel.
BYPASS DIODE CONNECTION
If you connected an inductor (door lock or alarm device) to the output relay, there should occur a voltage surge while the
inductor was between turning on and turning off. If you do not connect a reverse diode to the relay, the voltage surge will
cause damage to the electric circuit of the controller. To reduce this surge, it is recommended to connect the bypass
diode to the relay.
English9
installation and external connection
I/O CONNECTION
Input Connection
DOOR CONTACT (blue)
Door Contact Sensor
EXIT BUTTON
(green)
Exit Button
PUSH
DC +12V
GND
(black)
GND
DC +12V
(red)
DC 12V(+) POWER
- To connect the power supply unit
1. Connect the DC+12V to the red line.
2. Connect GND to the black line.
- To connect the Door Contact Sensor
1. Connect the COM port of the sensor to the blue line.
2. Connect the NO port of the sensor with the GND line.
- To connect the Exit Button
1. Connect one end of the button to the green line.
2. Connect the other end of the button to GND.
10_ Installation and External Connection
Output Connection
DOOR LOCK OUT
(white)
Door Lock
INSTALLATION AND EXTERNAL CONNECTION
ALARM OUT
(purple)
Alarm Device
Lock Type Select
(yellow)
Cathode
Anode
1N4004 ~ 1N4007 or equiv.
DC +12V
GND
DC 12V(+) POWER
- To connect the power supply unit
1. Connect the DC+12V to the red line.
2. Connect GND to the black line.
- To connect the door lock device
1. Connect the plus(+) line of the lock device to DC+12V.
2. Connect the minus(-) line of the lock device to the white line.
- To connect the alarm device
1. Connect the plus(+) line of the alarm device to DC+12V.
2. Connect the minus(-) line of the alarm device to the purple line.
- To specify the lock type
POWER FAIL SAFE: Connect the yellow line to GND.
POWER FAIL SECURE: Leave the yellow line in the floating state.
English11
system initialization & basic operations
INITIALIZING THE SYSTEM BY SHORT-CIRCUITING
1. Turn off the product and short-circuit three lines: white line of
the door lock device, green line of the Exit button, and yellow
line of the lock type.
Short-Circuit
White
2. When you turn the product back on, all of the LED indicators
turn red or green, repeat turning on/off twice before being
completely turned off.
Door Lock
Green
Exit Button
Yellow
Lock Type
3. In the power-off condition, all LED indicators turn green
bottom up in sequence.
4. When you hear a beep 4 times, that indicates that the
initialization is completed.
Black
Power
M
Red
 If you initialize the system, all of the data settings will return to the factory default.
BASIC OPERATIONS
When the power is supplied
1. All of the LED indicators will turn red or green, and repeat turning ON/OFF twice before being completely turned
OFF. In the power-off condition, all LED indicators turn red bottom up in sequence.
2. You will hear a beep once.
When you present a registered card to the product or press the Exit button
1. All LED indicators turn from red to green, and turn off top down in sequence before turning back red.
2. Then, the door stays open for the specified time with the upper two indicators turning green, which indicates the
door is open.
3. You will hear a beep once.
When you present an unregistered card to the product
1. All LED indicators turn red, and repeat turning on/off twice before staying in ON.
2. You will hear a beep twice.
When you present a user card to the product while the door is open
1. The two LED indicators from the top stay green, indicating the door is open; in the mean time, the other
indicators reflect the authentication results.
12_ System Initialization & Basic Operations
TO REGISTER /DELETE MASTER ID
1. First turn off the product, and short-circuit two lines: purple line of
Alarm Out and blue line of the Door Contact Sensor.
SSA-S1000
Cable
Yellow
Green
Short-Circuit
3. Upon deletion of the Master Card, you will hear a beep once and
all of the LED indicators toggle between green and red twice
before turning off; in this condition, they turn red from bottom up
in sequence.
Purple
White
Red
DC12V
4. When the deletion is completed, turn off the product.
Connect the purple line of Alarm Out and the blue line of the Door
Contact Sensor back to their original ports, respectively.
Power
GND
Black
5. When you turn the product back on, it recognizes and registers the first-read card as the Master Card. And
if you present a registered user card to the product upon deletion of the Master Card, that card will be
registered as the Master Card.
M
 If you present a registered user card after the Master Card is deleted, that card will be registered as the Master Card.
TO REGISTER/DELETE ID CARD
1. If you present the Master Card to the product, it will sound the beep
once and the first three LED indicators from the top will turn green
from the top.
SSA-S1000
MASTER CARD
2. If you present a new user card to the product, it will sound the beep
once and all of the LED indicators except for the first three ones from
the top will turn from red to green. Then, they all turn off and turn
back on bottom up in sequence. When all of the LED indicators turn
back on, they will turn red except for the first three LED indicators
from the top . Then, the user card will be registered.
3. If you present a registered user card, the product will sound the beep twice and all LED indicators except for the
first 3 from the top will turn red, and repeat turning on/off twice before being completely ON. Then the user card
will be deleted.
4. When you present the Master Card to the product after the user card is deleted, the product will sound the
beep once and all of the LED indicators turn red, starting with the first three LED indicators from the top turning
from green to red.
M
 If you present a registered user card after the Master Card is deleted, that card will be registered as the Master Card.
English13
SYSTEM INITIALIZATION & BASIC OPERATIONS
Blue
2. When you turn the product back on, you will hear the beep twice while
all of the LED indicators turn red, and repeat turning on/off twice before
being completely ON; then the Master card will be deleted.
troubleshooting
TROUBLESHOOTING
If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact
the SAMSUNG Customer Service near you.
PROBLEM
SOLUTION
The user card is not deleted.
1)
The Exit button does not work at all.
1)
14_ troubleshooting
Check if the product works properly.
- If the product works properly and you have the Master Card
c Read the Master Card.
d Read the card to delete.
e Read the Master Card again to switch to normal mode.
f For more information about deleting user cards, refer to the ID registration and
deletion section in this manual.
- If you lost the Master Card
c Turn off the product and short-circuit the purple and blue lines, then turn the
product back on.
d The Master ID will be deleted with a flashing LED indicator and beep.
e When the Master card is deleted, turn off the product and restore the purple
and blue lines to their respective original positions.
f The very first card read by the product after turning on the product will be
registered as the Master Card.
g For deleting the ID once the Master Card is registered, refer to the ID
registration and deletion section in this manual.
h Turn off the product and short-circuit the purple and blue lines, then turn the
product back on.
i The Master ID will be deleted with a flashing LED indicator and beep.
j When the Master card is deleted, turn off the product and restore the purple
and blue lines to their respective original.
k The very first card read by the product after turning on the product will be
registered as the Master Card.
Check if the Exit button is connected to SSA-S1000 properly. (the Exit button
should be used with a NO-type button)
2) Check if the Exit button works normally.
- Check the connection cable between the Exit button and SSA-S1000 for any
disconnection or short-circuit.
- Try to connect the two lines on the Exit button.
c If SSA-S1000 responds when you press the Exit button
√ Replace the Exit button as it is defective.
d If SSA-S1000 does not respond at all
√ Initialize the product as it is damaged or malfunctions. (Initializing the product
will lose all user data.)
3) If the trouble persists after following the procedures above, contact a designated
service center.
product specifications
PRODUCT SPECIFICATIONS
Item
SSA-S1000
512 Users
Power / Current
DC 12V / Max.110mA
Reading Time (Card)
30ms
Door Open Time
5sec. (Fixed)
Input Port
3ea: Exit Button, Door Sensor, Lock Type Select [Power fail Safe / Power Fail Secure]
Output Port
2ea : TR Output / DC 12V. Rating Max. 300mA Alarm Output, DC 12V. Rating Max.
1A Lock Output
LED Indicator
9 LED Indicators (Red and Green)
Beeper
Piezo Buzzer
Operating Temperature
-20°C to +50°C
Operating Humidity
10% to 90% Relative Humidity Non-Condensing
Color / Material
Silver with Black/ Polycarbonate
Dimension
(W x H x D(mm))
45.0 x 122.0 x 25.0
Weight
130g
English15
PRODUCT SPECIFICATION
Users
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of
with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate
that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are
not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.
AB82-02558A