Makita BMR100 Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Radio
BMR100
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Always recycle batteries
Li-ion
IMPORTANT SAFETY
INSTRUCTIONS
WARNING:
When using electric tools, basic safety precautions should
always be followed to reduce the risk of fire, electric
shock, and personal injury, including the following:
1. Read this instruction manual and the charger
instruction manual carefully before use.
2. Clean only with dry cloth.
3. Do not block any ventilation opening. Install in
accordance with the manufacturer’s instruction.
4. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
5. Only use attachments/accessories specified by the
manufacturer.
6. Unplug this apparatus during lighting storms or when
unused for long periods of time.
7. A battery operated radio with integral batteries or a
separate battery pack must be recharged only with the
specified charger for the battery. A charger that may
be suitable for one type of battery may create a risk of
fire when used with another battery.
8. Use battery operated radio only with specifically
designated battery packs. Use of any other batteries
may create a risk of fire.
9. When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause sparks, burns,
or a fire.
10. Avoid body contact with grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is
grounded.
SAVE THESE INSTRUCTIONS.
Features:
•
•
•
•
•
•
•
•
•
•
•
AM/FM-stereo PLL Synthesized
Large LCD display with illumination
Manual/Preset/Scan tuning
Rotary tuning and volume control
5 preset stations each band
Time and 2 alarm timers (radio and HWS buzzer) with
Snooze
Adjustable sleep (auto shut off) timer
Stereo speaker for rich sound performance
Ultra rugged design
Water resistant to JIS 4
Powered by both Makita battery pack and supplied
power adaptor
Explanation of general view
10
2 3
12
14
1
4
5
6
7
9
8
13
2
L K
15
A
B
11
J
PM
C
I
D
H
E
G
F
Controls:
1. Power and Sleep timer
2. Band/Tuning step selection and Mono button
3. Radio alarm set
4. Buzzer alarm set
5. Preset stations
6. Scan tuning and Time set
7. Volume and Tuning controls
8. DC IN socket
9. Input terminal (AUX IN1)
10. Soft bended rod antenna
11. Battery compartment (covering main battery pack and
back up batteries)
12. Handle
13. Speaker
14. Battery compartment locker
15. Input terminal (AUX IN2)
Battery Installation
Note:
Keeping back up batteries inside the compartment
prevent stored data in preset memories from being lost.
1. Pull out the battery compartment locker to release
battery compartment. There are main battery pack
compartment and back up battery compartment.
1. Battery
compartment
(covering main
2
battery pack and
back up
batteries)
2. Battery
compartment
locker
1
LCD Display:
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Radio alarm
HWS buzzer alarm
Scan tuning
Band Indicator
Low battery indicator
Preset stations
Sleep and Snooze status
Frequency
Stereo symbol and Volume
Clock
Time set
PM for clock
1. Main battery
compartment
2. Back up battery
compartment
1
1
2
3
2. Remove back up battery compartment cover and
insert 2 fresh UM-3 (AA sizes). Make sure the
batteries are with correct polarity as shown inside the
compartment. Replace the battery cover.
3. BH2433 | BH2420 After back up batteries are
inserted, insert the main battery pack to power radio.
The suitable battery packs for this radio listed as
below.
it into place. Always insert it all the way until it locks in
place with a little click.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
• To remove the battery cartridge, withdraw it from the
tool while sliding the button on the front of the cartridge
or pressing the buttons on both sides of the cartridge.
Cluster Battery:
9.6V: 9135 | 9134 | 9122 | PA09 | 9120
1235 | 1234 | 1222 | PA12 | 1220
3-2. Installing or removing Cluster
battery cartridge
14.4V: 1435 | 1434 | 1422 | PA14 | 1420
1. Battery cartridge
12V:
18V:
1835 | 1834 | 1822 | PA18
Slide Battery:
9.6V: BH9033 | BH9033A | BH9020 | BH9020A
12V:
1
BH1233 | BH1233C | BH1220C
14.4V: BH1433 | BH1420 | BL1430
18V:
BL1830
24V:
BH2433 | BH2420
The following tables indicate the operating time on a
single charge.
Battery Cartridge•Voltage
Battery
Capacity
1.3 Ah
1.5 Ah
9.6V
12V
14.4V
PA09
PA12
PA14
9120
1220
1420
–
–
–
1222
1422
9122
2.0 Ah
BH9020
BH9020A
9134
1234
3.0 Ah
9135
1235
BH9033
BH1233
3.3 Ah
BH9033A BH1233C
(At Max.
24V
PA18
–
Approx. 7 hour
BL1815
–
Approx. 8 hour
1822
BH2420
Approx. 11 hour
1434
1834
–
Approx. 13 hour
1435
1835
BL1430
BL1830
–
Approx. 16 hour
BH1433
–
BH2433
Approx. 17 hour
BH1220C BH1420
2.6 Ah
Operating time*
18V
Volume)
* Operating time may differ by the type of battery, charging or
operating conditions.
3-1. Installing or removing Slide
battery cartridge
1
3
1. Button
2. Battery cartridge
3. Red part
2
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
4
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
• To remove the battery cartridge, withdraw it from the
Job site radio.
4. Replace battery compartment locker.
5. Reduced power, distortion and a “stuttering sound” or
low battery sign
that appears on the display are
all the signs that the main battery pack needs to
replace.
Note:
The battery pack can't be charged via the supplied AC
power adaptor.
6. When low battery sign
appears and an “E” keeps
on flashing is the time to replace the back up batteries.
Installing the Soft bended rod
antenna
1. Soft bended rod
antenna
1
band, rotate the radio to get best signal. Try to avoid to
operate the radio next to computer screen and other
equipment which will cause interference to the radio.
3. Press and release Scan button (long press Scan
button more than 2 seconds will activate time setting),
LCD display will flash Scan symbol and the radio will
up search and stop automatically when it finds a radio
station,. Press the Scan button again to pick up the
found station.
Note:
A stereo symbol will appear on the display, if the
station found is a stereo station.
Install the Soft
bended rod antenna as show in the figure.
Using Supplied AC power adaptor
1
1. DC IN socket
2. Input terminal
(AUX IN1)
Note:
The radio will continue to search next available
stations if you do not press Scan button again when it
finds a radio station.
4. Rotate the Volume control to get required sound level.
LCD display will show sound level changes.
Note:
During operating volume control, you can press in
Tuning/Volume control knob to change volume control
to tuning control status.
5. To turn off the radio, press the Power button. Display
will show OFF.
Manual Tuning
2
Remove the rubber protector and insert the adaptor plug
into the DC socket on the front side of the radio. Plug the
adaptor into a standard mains socket outlet. Whenever
the adaptor is used, the battery pack are automatically
disconnected. The AC adaptor should be disconnected
from the main supply when not in use.
Setting the clock
1. Clock can be set either when the radio is power on or
off.
2. Display will show “-: - -” when the back up batteries
are installed.
3. Long press the time set button
for more than
2 seconds, display will flash time set symbol
and
also the hour digit, followed by a beep.
4. Rotate Tuning control to set the required hour.
5. Press
button to confirm hour setting, the minute
digit will flash.
6. Rotate Tuning control to set the required minute.
7. Press the
button again to complete clock setting.
Operating the radio
This radio equips with three tuning methods – Scan
tuning, Manual tuning and Memory presets recall.
Scan Tuning
1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band
button. Make sure the rubber bended rod antenna has
been well placed for best FM reception. For AM (MW)
1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band
button. Adjust the antenna as described above.
3. A single rotary to the Tuning control will change the
frequency in the following increment:
FM: 50 or 100 kHz
AM (MW): 9 or 10 kHz
Note:
If the radio is in volume control status, press in the
tuning/volume control to become Tuning status.
4. Keep on rotating the Tuning control until the required
frequency shown on the display.
5. Rotate the volume control to get required sound level.
6. To turn off the radio, press the Power button. Display
will show OFF.
Storing stations in preset memories
There are 5 memory presets for each waveband.
1. Press the Power button to turn on the radio.
2. Tune to required station using one of the methods
previously described.
3. Press and hold down the required preset until radio
beeps. The preset number will appear in the display
and the station will be stored under chosen preset
button.
4. Repeat this procedure for the remaining presets.
5. Stations stored in preset memories can be overwritten
by following above procedures.
Recall stations from preset memories
1. Press the power button to turn on the radio.
2. Select the required waveband.
5
3. Momentarily press the required Preset button, the
preset number and station frequency will appear in the
display.
Setting the radio alarm
When the radio alarm is selected, the radio will turn on
and play the chosen radio station at the chosen alarm
time. The radio alarm will continue for one hour unless
turned off by pressing the Power button. Pressing the
Power button whilst the alarm is activated will cancel the
alarm for 24 hours.
Note:
When the radio is in low battery status, the radio alarm
can't be activated.
a. Setting radio alarm time:
1. The radio alarm can be set either when radio is on or
off.
2. Press and release radio alarm button
, the
radio alarm symbol will flash.
3. During radio alarm symbol flashing, press
button
for more than 2 seconds followed by a beep.
4. Display Hour will flash, rotate Tuning Control to select
the hour then press
button again to confirm hour
setting.
5. Follow same procedures of setting hour to set
required minute. Press
button to complete alarm
time setting.
b. Setting radio alarmed station
1. During setting radio alarm time and radio alarm
symbol is flashing, press Band button to activate the
radio to select required wake-up band and station by
manual tuning and recall the preset stations. Press
button to complete radio alarm setting.
Display will show
.
2. When above radio alarm time and station are set,
press and hold down radio alarm button
for
2 seconds followed by a beep to switch alarm on or
off. Display will show
when radio alarm is set.
Note:
If new radio alarm station is not selected, it will select
the last alarm station.
3. During the symbol flashes, long pressing the
button for more than 2 seconds followed by a beep
and display Hour digit will flash.
4. Rotate Tuning Control to select required alarm hour,
then press time set button
again. The minute
digit will then flash.
5. Rotate Tuning Control to select required alarm minute,
the press time set button
again to complete HWS
buzzer alarm setting.
6. Press and hold down buzzer alarm button
for
more than 2 seconds followed by a beep to switch on
or off the HWS buzzer alarm.
Display will appear
when buzzer alarm has
been set.
Snooze function
1. Whilst the alarm is activated, pressing any buttons
except the Power Button will activate the snooze
function. The radio or HWS buzzer alarm will be
silenced with interval of 5 minutes.
2. The display will flash both the snooze symbol
and
the alarm symbol. The snooze function can be
repeatedly during one hour that the alarms are active.
Sleep function
The sleep timer will automatically switched off the radio
after a preset time has elapsed.
1. Press and continue to hold down the Power button for
more than 2 seconds, followed by a beep tone, the
display will cycle through the available sleep times in
the order 60-45-30-15-120-90-60.
Release the Power button when the required sleep
time appears in the display. The
symbol will
appear in the display and the radio will play the last
station selected.
2. To cancel the sleep function, press the Power button.
The Symbol will disappear and radio is off.
Display illumination
Press any buttons or rotate tuning/volume control will
illuminate the LCD display for approx. 15 seconds. During
scanning stations and alarm activated, will also
automatically illuminate the display.
Setting the HWS (Humane Wake
System) buzzer alarm
Setting tuning step
A beep tone will activate when selecting the HWS buzzer
alarm.
The alarm beep will become shoter and shoter every
15 seconds for one minute followed by one minute silence
before repeating the cycle.
The HWS alarm will sound for one hour until turning off by
pressing the Power button. Press the Power button whilst
the alarm is activated will cancel the alarm for 24 hours.
1. The HWS buzzer alarm can be set either radio is on or
off.
2. Press and release the HWS buzzer alarm button
, the symbol will flash.
Tuning steps on some countries are different from where
you purchase the radio. If you buy the radio in Europe and
intend to use in Northern America or some Southern
American countries, you may have to adjust tuning step
so the radio may continue to serve you well.
While radio is switched off, long pressing Step/Band
button for more than 2 seconds will first show current FM
tuning step.
Continue pressing Step/Band button for approx. another
5 seconds until display FM and 50 kHz (tuning step)
flashing followed by a beep. By rotating the Tuning
control, you may adjust to 100 kHz per tuning step.
6
After FM tuning step is reset, pressing Step/Band button
again, display will show AM (MW) and flash 9 kHz. By
rotating Tuning control, you may adjust to 10 kHz per
tuning step. Complete the setting by pressing Step/Band
button.
Change Stereo to Mono
When the stereo FM station reception is weak, you can
improve it by pressing Mono button for 2 seconds. The
sound is no longer in stereo and stereo indicator
disappears.
How to play other audios
CAUTION:
Unplug this apparatus before connecting other
audios.
• There are 2 AUX in sockets. AUX 1 is located on the
front panel, and AUX 2 is located in the battery
compartment.
• Connect a stereo or mono source (i.e. iPod, MP3, or
CD player) to either AUX 1 or AUX 2 by audio cord.
• Repeatedly press and release the BAND button until
AU1” or “AU2” is displayed, then AUX function is
activated.
• AUX can't be activated as alarm source.
MAINTENANCE
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Specifications:
Power Requirements
AC power adaptor
DC12V 700mA, center pin positive
Battery
UM-3 (AA size) x 2 for back up
Cluster battery: 9.6 - 18V
Slide battery: 9.6 - 24 V
Frequency coverage FM 87.50 - 108 MHz
AM (MW) 522 - 1629 kHz
(9 kHz/step)
Circuit feature
Loudspeaker
3 inches 8 ohm
Output Power
9.6V: 0.8 W x 2, 12V: 1.2 W x 2
14.4V: 2W x 2, 18V: 3W x 2
24V: 5W x 2
Input terminal
3.5 mm dia. (AUX IN1/AUX IN2)
Antenna system
FM: soft bended rod antenna
AM: bar antenna
Dimension (W x H x D) in mm
263 x 305 x 166
Weight
4.2kg (without battery)
7
Makita Corporation
Anjo, Aichi, Japan
3A81QP5Z40000
BMR100_ENGE_1009