advertisement
PICDEM™ 2 Plus
Demonstration Board
User’s Guide
2011 Microchip Technology Inc.
DS41584A
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions.
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE
.
Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights.
DS41584A-page 2
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
K
EE
L
OQ
, K
EE
L
OQ
logo, MPLAB, PIC, PICmicro, PICSTART,
PIC
32
logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
MPLINK, mTouch, Omniscient Code Generation, PICC,
PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
All other trademarks mentioned herein are property of their respective companies.
© 2011, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-61341-248-0
Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC ® MCUs and dsPIC ® DSCs, K
EE
L
OQ
® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.
2011 Microchip Technology Inc.
PICDEM™ 2 PLUS DEMONSTRATION
BOARD USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 5
Chapter 1. Introduction
Development Kit Contents ...................................................................... 11
PICDEM™ 2 Plus Demonstration Board ................................................ 11
On-Board Jumper Configurations ........................................................... 13
Chapter 2. Getting Started
PICDEM™ 2 Plus Demonstration Board as a Stand-Alone Board –
Preprogrammed Device .......................................................................... 15
Programming the Device ........................................................................ 16
Chapter 3. Tutorial
Tutorial Program Operation .................................................................... 23
Source Code and Application Notes ....................................................... 28
Appendix A. Hardware Detail
Board Layout and Schematics ................................................................ 34
Worldwide Sales and Service .................................................................................... 38
2011 Microchip Technology Inc.
DS41584A-page 3
PICDEM™ 2 Plus Demonstration Board User’s Guide
NOTES:
DS41584A-page 4
2011 Microchip Technology Inc.
PICDEM™ 2 PLUS DEMONSTRATION
BOARD USER’S GUIDE
Preface
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our web site
(www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is
“DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the document.
For the most up-to-date information on development tools, see the MPLAB
®
IDE on-line help.
Select the Help menu, and then Topics to open a list of available online help files.
INTRODUCTION
This chapter contains general information that will be useful to know before using the
PICDEM™ 2 Plus Demonstration Board. Items discussed in this chapter include:
• Conventions Used in this Guide
• Development Systems Customer Change Notification Service
DOCUMENT LAYOUT
This document describes how to use the PICDEM™ 2 Plus Demonstration Board as a development tool to emulate and debug firmware on a target board. The manual layout is as follows:
•
– Introduces the PICDEM 2 Plus Demonstration
Board and provides a brief description of the hardware.
•
– Goes through a basic step-by-step process for getting your PICDEM 2 Plus Demonstration Board up and running as a stand-alone board or with an ICE, ICD or PICkit™ programmer.
•
– Provides a detailed description of the tutorial program.
•
– Describes in detail the hardware of the
PICDEM 2 Plus Demonstration Board.
2011 Microchip Technology Inc.
DS41584A-page 5
PICDEM™ 2 Plus Demonstration Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENTATION CONVENTIONS
Description Represents
Arial font:
Italic characters
Initial caps
Quotes
Referenced books
Emphasized text
A window
A dialog
A menu selection
A field name in a window or dialog
A menu path Underlined, italic text with right angle bracket
Bold characters
N‘Rnnnn
MPLAB
®
IDE User’s Guide
...is the
only
compiler...
the Output window the Settings dialog select Enable Programmer
“Save project before build”
File>Save
Examples
A dialog button
A tab
A number in verilog format, where N is the total number of digits, R is the radix and n is a digit.
A key on the keyboard
Click
OK
Click the
Power
tab
4‘b0010, 2‘hF1
Press <Enter>, <F1> Text in angle brackets < >
Courier New font:
Plain Courier New
Italic Courier New
Square brackets [ ]
Curly brackets and pipe character: { | }
Ellipses...
Sample source code
Filenames
File paths
Keywords
Command-line options
Bit values
Constants
A variable argument
Optional arguments
#define START autoexec.bat
c:\mcc18\h
_asm, _endasm, static
-Opa+, -Opa-
0, 1
0xFF, ‘A’
file
.o
, where
file
can be any valid filename mcc18 [options]
file
[options] errorlevel {0|1}
Choice of mutually exclusive arguments; an OR selection
Replaces repeated text
Represents code supplied by user var_name [, var_name...] void main (void)
{ ...
}
DS41584A-page 6
2011 Microchip Technology Inc.
Preface
WARRANTY REGISTRATION
Please complete the enclosed Warranty Registration Card and mail it promptly.
Sending in the Warranty Registration Card entitles users to receive new product updates. Interim software releases are available at the Microchip web site.
RECOMMENDED READING
This user’s guide describes how to use PICDEM™ 2 Plus Demonstration Board. Other useful documents are listed below. The following Microchip documents are available and recommended as supplemental reference resources.
Readme for PICDEM™ 2 Plus Demonstration Board
For the latest information on using the PICDEM™ 2 Plus Demonstration Board, read the “
Readme for PICDEM™ 2 Plus Demonstration Board.txt
” file (an ASCII text file) in the Readmes subdirectory of the MPLAB IDE installation directory. The
Readme file contains update information and known issues that may not be included in this user’s guide.
Readme Files
For the latest information on using other tools, read the tool-specific Readme files in the Readmes subdirectory of the MPLAB IDE installation directory. The Readme files contain update information and known issues that may not be included in this user’s guide.
Reference Documents
Reference documents may be obtained by contacting your nearest Microchip sales office (listed in the back of this document) or by downloading via the Microchip web site
(www.microchip.com). Recommended documents include:
• Individual data sheets and reference manuals:
- PIC16(L)F193X Data Sheet (
DS41364
)
- PIC18(L)F2X/4XK22 Data Sheet (
DS41412
)
-
PIC16(L)F1826/27 Data Sheet
(DS41391)
-
PICmicro
®
Mid-Range MCU Family Reference Manual
(DS33023)
-
PICmicro
®
18C MCU Family Reference Manual
(DS39500)
-
TC74 Data Sheet
(DS21462)
•
MPLAB
®
IDE Simulator, Editor User’s Guide
(DS51025)
•
MPASM™ Assembler, MPLINK™ Object Linker, MPLIB™ Object Librarian
User’s Guide
(DS33014)
•
PRO MATE
®
3 User’s Guide
(DS51464)
•
MPLAB
®
IDE PICSTART
®
Plus User’s Guide
(DS51028)
•
MPLAB
®
ICE Emulator User’s Guide
(DS51159)
•
MPLAB
®
ICD 3 In-Circuit Debugger Quick Start Guide
(DS51766)
2011 Microchip Technology Inc.
DS41584A-page 7
PICDEM™ 2 Plus Demonstration Board User’s Guide
THE MICROCHIP WEB SITE
Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers.
Accessible by using your favorite Internet browser, the web site contains the following information:
•
Product Support
– Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software
•
General Technical Support
– Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing
•
Business of Microchip
– Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
DEVELOPMENT SYSTEMS CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, access the Microchip web site at www.microchip.com, click on Customer
Change Notification and follow the registration instructions.
The Development Systems product group categories are:
•
Compilers
– The latest information on Microchip C compilers and other language tools. These include the MPLAB C18 and MPLAB C30 C compilers; MPASM™ and MPLAB ASM30 assemblers; MPLINK™ and MPLAB LINK30 object linkers; and MPLIB™ and MPLAB LIB30 object librarians.
•
Emulators
– The latest information on Microchip in-circuit emulators.This includes the MPLAB ICE 2000 and MPLAB ICE 4000.
•
In-Circuit Debuggers
– The latest information on the Microchip in-circuit debugger, MPLAB ICD 2.
•
MPLAB
®
IDE
– The latest information on Microchip MPLAB IDE, the Windows
®
Integrated Development Environment for development systems tools. This list is focused on the MPLAB IDE, MPLAB SIM simulator, MPLAB IDE Project Manager and general editing and debugging features.
•
Programmers
– The latest information on Microchip programmers. These include the MPLAB PM3 and PRO MATE
®
II device programmers and the PICSTART
®
Plus and PICkit™ 1 development programmers.
DS41584A-page 8
2011 Microchip Technology Inc.
Preface
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
Customers should contact their distributor, representative or field application engineer
(FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.
Technical support is available through the web site at: http://support.microchip.com
DOCUMENT REVISION HISTORY
Revision A (June 2011)
• Initial Release of this Document.
Note:
This board (DM163022-1) has been updated from the previous version
(DM163022).The user guide for the previous board version (DM163022) can be found online at the PICDEM 2 Plus web site (DS51275) www.Microchip.com/PICDEM2PLUS.
2011 Microchip Technology Inc.
DS41584A-page 9
PICDEM™ 2 Plus Demonstration Board User’s Guide
NOTES:
DS41584A-page 10
2011 Microchip Technology Inc.
PICDEM™ 2 PLUS DEMONSTRATION
BOARD USER’S GUIDE
Chapter 1. Introduction
1.1
INTRODUCTION
Thank you for purchasing the PICDEM™ 2 Plus Demonstration Board from Microchip
Technology Incorporated. The PICDEM 2 Plus Demonstration Board is a simple board that demonstrates the capabilities of Microchip’s 8-bit, 18-, 28- and 40-pin PIC16FXXX,
PIC16F1XXX, and PIC18 devices.
The PICDEM 2 Plus Demonstration Board can be used stand-alone with a programmed part, with an in-circuit emulator (for example, MPLAB
®
REAL ICE™) or with an in-circuit programmer/debugger (such as MPLAB
®
ICD 3 or PICkit™ 3).
Sample programs are provided to demonstrate the unique features of the supported devices.
1.2
DEVELOPMENT KIT CONTENTS
The PICDEM 2 Plus Demonstration Board kit comes with the following:
• PICDEM 2 Plus Demonstration Board (see Figure 1-1 )
• Sample devices (pre-loaded with program demonstration)
If you are missing any part of the kit, please contact your nearest Microchip sales office listed in the back of this publication for help.
1.3
PICDEM™ 2 PLUS DEMONSTRATION BOARD
The PICDEM 2 Plus Demonstration Board has the following hardware features:
1. 18-, 28- and 40-pin DIP sockets
(although three sockets are provided, only one device may be used at a time)
2. On-board, +5V regulator for direct input from 9V, 100 mA AC/DC wall adapter or
9V battery, or hooks for a +5V, 100 mA regulated DC supply
3. RS-232 socket and associated hardware for direct connection to an RS-232 interface
4. Programmer/debugger connectivity supporting MPLAB ICD 3, MPLAB REAL
ICE and PICkit 3
5. PICkit Serial Connector for analysis of serial communications peripherals such as SPI or I
2
C™
6. 5 k
pot for devices with analog inputs
7. Three push button switches for external stimulus and Reset
8. Power-on indicator LED
9. Four LEDs connected to PORTB
10. On-board external oscillators including: a) 4 MHz, canned crystal oscillator (Y2) b) RC oscillator circuit (R4, C3) c) Unpopulated holes for crystal connection (Y1) d) 32.768 kHz crystal for Timer1 clock operation (Y3)
2011 Microchip Technology Inc.
DS41584A-page 11
PICDEM™ 2 Plus Demonstration Board User’s Guide
5
11. 32K x 8 Serial EEPROM
12. LCD display
13. Piezo buzzer
14. Prototype area for user hardware
15. Expansion Header for PICtail™ daughter card connectivity or user access to
MCU pins
16. Microchip TC74 thermal sensor
FIGURE 1-1: PICDEM 2 PLUS DEMONSTRATION BOARD HARDWARE
2
8
9
9V BATTERY
PWR
3
10
1
12
6
M
PICDEM™ 2 PLUS
DEMO BOARD
PICtail™
16
11
:
:
13
7
15
DS41584A-page 12
2011 Microchip Technology Inc.
Introduction
1.4
ON-BOARD JUMPER CONFIGURATIONS
Most of the on-board components have associated jumpers that will allow the user to either connect or disconnect a component(s) from the PIC
®
MCUs or other mounted
components. Table 1-1 and Figure 1-2 detail these connections.
TABLE 1-1: ON-BOARD JUMPER CONNECTIONS
Jumper Connection
J6
J7
J9
J10
LEDs to PORTB
On-board RC oscillator to PIC
®
MCUs
Piezo buzzer to RC2 pin (*on 40-pin mid-range device, this is CCP1)
V
CAP
connection for devices with on-chip voltage regulator
J12 2.7V source to RA1 (voltage divider off of 9V input voltage)
J14, 15, 16, 17 PICkit™ Serial Header to I
2
C™ bus
J18,19 Tx and Rx from RS-232 components to PIC MCUs
J20, 21, 22, 23 PIC MCUs to I
2
C bus
J24 RA4 pin to RC2 pin (*on 40-pin mid-range device, this connects C1OUT to
CCP1)
FIGURE 1-2: PICDEM™ 2 PLUS DEMONSTRATION BOARD JUMPER
LOCATIONS
9V BATTERY
PWR
J6
J16
J17
J19
J18
J12
J7
M
J24
PICDEM™ 2 PLUS
DEMO BOARD
J20
J21
J10
:
:
J9
1.5
SAMPLE DEVICES
Two Flash devices are included. The device types may change, but will generally include PIC16 and PIC18 40-pin, DIP devices.
2011 Microchip Technology Inc.
DS41584A-page 13
PICDEM™ 2 Plus Demonstration Board User’s Guide
1.6
SAMPLE PROGRAMS
The PICDEM™ 2 Plus Demonstration Board kit sample demonstration programs can be found on the Microchip web site ( www.microchip.com/PICDEM2PLUS ). These programs may be used with the included sample devices, with a REAL ICE (In-Circuit
Emulator), MPLAB
®
ICD 3 (programmer/debugger) or with a PICkit™ 3
(programmer/debugger). For each type of device (PIC16 or PIC18), demo source code
(several
.C
and
.H
files) and compiled code (one
.hex
file) are provided.
DS41584A-page 14
2011 Microchip Technology Inc.
PICDEM™ 2 PLUS DEMONSTRATION
BOARD USER’S GUIDE
Chapter 2. Getting Started
The PICDEM™ 2 Plus Demonstration Board may be used as a stand-alone board with a preprogrammed device, with an In-Circuit Emulator (ICE), with an In-Circuit Debugger (ICD) or with a PICkit™ programming device. For a list of PIC
®
microcontroller compatible ICEs, ICDs or PICkit programming devices, see the Development Systems
Ordering Guide.
2.1
PICDEM™ 2 PLUS DEMONSTRATION BOARD AS A STAND-ALONE BOARD
– PREPROGRAMMED DEVICE
The PICDEM 2 Plus Demonstration Board may be demonstrated immediately by following the steps listed below:
• Place the preprogrammed sample device in the appropriate socket on the
PICDEM 2 Plus Demonstration Board.
• Confirm the jumpers are populated/removed according to Table 2-1 below.
• Connect the programmer/debugger. See
• Apply power to the PICDEM 2 Plus Demonstration Board. See
Section 2.3 “Powering the Board”
TABLE 2-1: JUMPER SETUP
2011 Microchip Technology Inc.
DS41584A-page 15
PICDEM™ 2 Plus Demonstration Board User’s Guide
To reprogram the sample device, the following will be necessary:
• Program source code – user source code may be used to program the device, or if this previously has been done, the sample program may be restored from the file included in the PICDEM 2 Plus installer.
• An assembler, such as MPASM™ assembler (available with MPLAB
®
IDE), or a compiler, such as HI-TECH
®
C or MPLAB C18 (PIC18 devices only).
Source code must be assembled or compiled into a hex file before it can be programmed into the device. Microchip Technology’s MPASM assembler, HI-TECH or C18
C compilers may also be used. Both are compatible with MPLAB IDE.
Other assemblers/compilers may be used. For a list of these PIC MCU compatible language tools, see the Microchip web site (www.microchip.com).
Once the sample program is in hex file format, a programmer can program a Flash device. Microchip Technology’s PICkit or ICD 3 programmer may be used. Both are compatible with MPLAB IDE.
Other programmers may be used. For a list of these PIC MCU compatible programmers, see the Microchip web site (www.microchip.com).
If the code protection bit(s) have not been programmed, the on-chip program memory can be read out for verification purposes.
2.2
PROGRAMMING THE DEVICE
The PICDEM 2 Plus Demonstration Board supports the ability to program a device through multiple options.
2.2.1
PICkit Programming
FIGURE 2-1: PICkit™ PROGRAMMER AND BOARD CONNECTION
HEADER
DS41584A-page 16
Microchip’s PICkit 3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer.
2011 Microchip Technology Inc.
Getting Started
Connecting the PICkit programmer to the PICDEM 2 Plus Demonstration Board is quick and easy.
• First connect the PICkit 3 as shown in Figure 2-1
.
• Make sure to connect the USB cable to the PICkit 3 and to the computer.
• Enter MPLAB and go to either the
Debugger
or
Programmer
tab. Select the
PICkit 3 as shown in
.
FIGURE 2-2: CONNECTING A PICkit PROGRAMMER
2011 Microchip Technology Inc.
DS41584A-page 17
PICDEM™ 2 Plus Demonstration Board User’s Guide
2.2.2
ICD Programming
FIGURE 2-3: ICD PROGRAMMER AND BOARD CONNECTION HEADER
The MPLAB
®
ICD 3 In-Circuit Debugger System is Microchip’s most cost-effective, high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices. It debugs and programs PIC microcontrollers and dsPIC
®
®
Flash
DSCs with the powerful, yet easy-to-use graphical user interface of MPLAB Integrated Development Environment (IDE).
Connecting the ICD 3 to the PICDEM 2 Plus Demonstration Board is quick and easy.
• First connect the ICD 3 as shown in
.
• Make sure to connect the USB cable to the ICD 3 and to the computer.
• Enter MPLAB and go to either the
Debugger
or
Programmer
tab. Select the ICD
3 as shown in
.
DS41584A-page 18
2011 Microchip Technology Inc.
FIGURE 2-4: CONNECTING AN ICD
Getting Started
2011 Microchip Technology Inc.
DS41584A-page 19
PICDEM™ 2 Plus Demonstration Board User’s Guide
2.3
POWERING THE BOARD
The PICDEM 2 Plus Demonstration Board supports the ability to power the board through multiple options.
2.3.1
External 9V Connector
FIGURE 2-5: 9V EXTERNAL POWER SUPPLY
The PICDEM 2 Plus Demonstration Board can be powered with an external 9V power supply.
• Connect 9V power supply to a wall outlet.
• Connect to board as shown in Figure 2-5 . The on-board regulator will reduce the
input voltage to 5V for safe PIC device operation.
2.3.2
External 9V Battery
FIGURE 2-6: 9V EXTERNAL BATTERY
DS41584A-page 20
The PICDEM 2 Plus Demonstration Board can be powered with an external 9V battery for a power supply.
• Connect the 9V battery to the board [B].
• The on-board regulator will reduce the input voltage to 5V for safe PIC device operation.
2011 Microchip Technology Inc.
2.3.3
Power by Programmer
FIGURE 2-7: 5V SUPPLIED BY PROGRAMMER
Getting Started
The PICDEM 2 Plus Demonstration Board can also be powered with a PICkit or ICD programming device.
• To power the device with a programmer go to either the
Debuggger
/
Programmer
tab.
• Scroll down to Settings. Then go to the
Power
tab.
• Click the checkbox labeled “Power target circuit from MPLAB (programmer type)”.
Select 5V as the voltage.
• The board will now be powered through the programmer.
2011 Microchip Technology Inc.
DS41584A-page 21
PICDEM™ 2 Plus Demonstration Board User’s Guide
NOTES:
DS41584A-page 22
2011 Microchip Technology Inc.
PICDEM™ 2 PLUS DEMONSTRATION
BOARD USER’S GUIDE
Chapter 3. Tutorial
The tutorial program is preprogrammed into the sample device. The PIC16 device’s program was built using the HI-TECH C compiler and the PIC18 device’s program was built using the C18 compiler. These programs are included in the PICDEM™ 2 Plus installer file found at www.Microchip.com/PICDEM2PLUS .
In case the device has been reprogrammed to a user’s unique code, the device can always be reprogrammed with the tutorial program if installed.
For detailed information on the PICDEM 2 Plus hardware, please refer to
3.1
TUTORIAL PROGRAM OPERATION
The tutorial program is made up of four components, which are individually displayed on the LCD.
3.1.1
Voltmeter
FIGURE 3-1: VOLTMETER DISPLAY AND COMPONENT
This mode uses the A/D module to measure the voltage of the RA0 pot (R16) and display a voltage between 0.00V and 5.00V on the LCD.
Voltage is continually updated until the mode is exited by pressing RB0.
FIGURE 3-2: TEMPERATURE READINGS
Reading the Voltmeter Display (ADC)
A) (ADRESH:ADRESL) ADC conversion result. Range: 10-bit (0-1023).
B) Voltage representation.
2011 Microchip Technology Inc.
DS41584A-page 23
PICDEM™ 2 Plus Demonstration Board User’s Guide
3.1.2
Buzzer
FIGURE 3-3: BUZZER DISPLAY AND COMPONENT
This mode turns on the Piezo buzzer using the CCP1 module I/O pin, RC2.
FIGURE 3-4: FIGURE 3-4: BUZZER READINGS
DS41584A-page 24
Reading the Buzzer Display (PWM)
A) PWM Period Percentage. Range (0-100%) Frequency (10 kHz-250 Hz).
- Please refer to Table 3-1 for a index of Period, PWM%, Frequency and Key.
B) This is the key being played based on the frequency being supplied to the speaker.
C) Increase the PWM period by 2%.
The period and duty cycle of the CCP1 frequency can be changed while the buzzer is on. The changes in period are recognized immediately in the buzzer tone. By changing the period, the buzzer frequency changes.
• To change the period, press RB0 under the “Buzzer” menu.
• The buzzer will sound off with the default frequency of 10 kHz and a period of 05h
(0%).
• By pressing the RB4 button the period will increase by 5 (2%).
• The LCD will display the current Key being played by the buzzer based upon the period.
• Press RB0 to exit the buzzer function.
Figure 3-3 shows an example of a signal supplied to the buzzer.
2011 Microchip Technology Inc.
FIGURE 3-5: BUZZER SIGNAL
Tutorial
TABLE 3-1: BUZZER INDEX
2011 Microchip Technology Inc.
DS41584A-page 25
PICDEM™ 2 Plus Demonstration Board User’s Guide
3.1.3
Temperature
FIGURE 3-6: TEMPERATURE DISPLAY AND COMPONENT
This mode uses a TC74 thermal sensor to measure ambient temperature in Celsius and then display the temperature on the LCD. The user has the option to change the display between Celsius and Fahrenheit by pressing RB4.
Communication between the PIC MCU and sensor is accomplished using the MSSP module. This mode is exited by pressing RB0.
FIGURE 3-7: TEMPERATURE READINGS
DS41584A-page 26
Reading the Temperature Display
A) Display current temperature at given unit of measurement
B) Change the unit of measurement.
3.1.4
Temperature Fault
If during I
2
C communication a time-out Fault occurs the LCD display will indicate the
Fault as shown in Figure 3-8 .
FIGURE 3-8: TEMPERATURE COMMUNICATION FAULT
2011 Microchip Technology Inc.
Tutorial
3.1.5
Clock
FIGURE 3-9: CLOCK DISPLAY
The Real-Time Clock will start counting from 00:00:00 at the start of the program.
The Timer1 module and a 32 kHz clock crystal are used to establish a Real-Time Clock.
By pressing RA4 within the clock function, the clock time can be set to the user’s preference. The user has the option to set the hours or minutes of the clock.
FIGURE 3-10: INCREMENT/DECREMENT HOURS
By pressing RA4 within the set function, the user can set the hours. The user first has the option to increment the hours, one hour at a time by pressing RA4. If the user presses RB0 within the increment hour’s function, the program will then allow the user to decrement the hours, one hour at a time by pressing RA4. When the user presses
RB0 again the program will return to the clock display screen.
FIGURE 3-11: INCREMENT/DECREMENT MINUTES
By pressing RB0 within the set function, the user can set the minutes. The user first has the option to increment the minutes, one minute at a time by pressing RA4. If the user presses RB0 within the increment minute’s function, the program will then allow the user to decrement the minutes, one minute at a time by pressing RA4. When the user presses RB0 again the program will return to the clock display screen.
2011 Microchip Technology Inc.
DS41584A-page 27
PICDEM™ 2 Plus Demonstration Board User’s Guide
3.1.6
USART
FIGURE 3-12: USART DATA IN HYPERTERMINAL
The data displayed on the LCD within all the program functions is also sent to the
RS-232 serial port using the USART on the PIC MCU. A HyperTerminal program on the
PC will be able to display the same information that is displayed on the LCD.
3.2
SOURCE CODE AND APPLICATION NOTES
In addition to the assembled tutorial program (hex files), source code used to create these hex files are included in the PICDEM 2 Plus installer. Both source code and related hex files are found in device-specific directories.
A digital guide is also included with the installer.
For information on how to reprogram the device with new or modified code, or how to
restore the tutorial program, please see
Section 2.1 “PICDEM™ 2 Plus Demonstration Board as a Stand-Alone Board – Preprogrammed Device”
DS41584A-page 28
2011 Microchip Technology Inc.
Tutorial
FIGURE 3-13: TUTORIAL PROGRAM FLOWCHART
Power-Up
PICDEM™ 2 Plus
Welcome Screen
RA4
Voltmeter
RA4 = Next
RB0 = Now
RA4
Buzzer
RA = Next
RB0 = Now
RA4
Temperature
RA4 = Next
RB0 = Now
RA4
Clock
RA4 = Next
RB0 = Now
RB0
RB0
RB0
Volts = 3.3V
[0681] RB0 = Exit
PWM:044% Key:C5
RA4 = +2% RB0 = Exit
Temp = 23° [C]
RA4 = [F] RB0 = Exit
RB0
Time 00:00:00
RA4 = Set RB0 = Menu
RA4
RA:[HR] 00:00:00
RB:[MIN] TIME
RB0
RA4
00:00:00 *[HRS]
RA:++/-- RB:Next
RB0
RB0
00:00:00 *[MIN]
RA:++/-- RB:Next
USART
Transmit
2011 Microchip Technology Inc.
DS41584A-page 29
PICDEM™ 2 Plus Demonstration Board User’s Guide
NOTES:
DS41584A-page 30
2011 Microchip Technology Inc.
PICDEM™ 2 PLUS DEMONSTRATION
BOARD USER’S GUIDE
Appendix A. Hardware Detail
The PICDEM™ 2 Plus Demonstration Board hardware is extremely simple and illustrates the ease-of-use of various PIC MCUs. This section describes the PICDEM 2 Plus
Demonstration Board hardware elements.
A.1
PROCESSOR SOCKETS
Although three sockets are provided, only one device may be used at a time.
• 18-pin socket
• 28-pin socket
• 40-pin socket
A.2
DISPLAY
• Four green LEDs are connected to PORTB of each processor type.
• PORTB pins are set high to light the LEDs. These LEDs may be disconnected from PORTB by removing jumper J6.
• One red LED is provided to indicate whether there is power to the PICDEM 2 Plus
Demonstration Board.
• LED On = Powered. LED Off = Not Powered
A.3
POWER SUPPLY
There are multiple ways to supply power to the PICDEM 2 Plus Demonstration Board:
• A 9V battery can be plugged into J8.
• A 9V, 100 mA unregulated AC or DC supply can be plugged into J2. A power supply can be purchased through Microchip, part #AC162039.
• A +5V, 100 mA regulated DC supply can be connected to the hooks provided.
MPLAB
®
ICE 2000 users have a regulated +5V power supply available in the logic probe connector and can easily connect to the header (J4) on the PICDEM 2 Plus
Demonstration Board. (Red probe to +5V and Black probe to GND.)
MPLAB ICD or PICkit™ programmer users may use the programmer to power the target board to 5V, up to 200 mA, if the MPLAB programmer is connected to the PC.
A.4
RS-232 SERIAL PORT
An RS-232, level-shifting IC has been provided with all the necessary hardware to support connection of an RS-232 host through the DB9 connector. The port is configured as DCE and can be connected to a PC using a straight-through cable.
The PIC16/PIC18 RX and TX pins are tied to the RX and TX lines of the MAX232A.
2011 Microchip Technology Inc.
DS41584A-page 31
PICDEM™ 2 Plus Demonstration Board User’s Guide
A.5
SWITCHES
Three switches provide the following functions:
• S1 – MCLR to hard reset the processor
• S2 – Active-low switch connected to RA4
• S3 – Active-low switch connected to RB0
Switches S1 and S3 have debounced capacitors, where as S2 does not, allowing the user to investigate debounced techniques.
When pressed, the switches are grounded. When idle, they are pulled high (+5V).
A.6
OSCILLATOR OPTIONS
• 32.768 kHz (watch-type) crystal for Timer1.
• Removable, 4 MHz, canned oscillator.
• Space for a user defined oscillator crystal.
A.7
ANALOG INPUT
A 5 Ω potentiometer is connected through a series 470 Ω resistor to AN0.
The pot can be adjusted from V
DD
to GND to provide an analog input to the parts with an A/D module.
A.8
ICD CONNECTOR
By way of the modular connector (J5), the MPLAB ICD can be connected for low-cost debugging. The ICD connector utilizes RB6 and RB7 of the microcontroller for in-circuit debugging.
A.9
PICkit™ CONNECTOR
By way of the header connector (J11), the MPLAB PICkit can be connected for low-cost debugging.
A.10 TEMPERATURE SENSOR
This is a serial digital thermal sensor (TC74) connected to the 28- and 40-pin microcontrollers via RC3 and RC4.
Communication is accomplished with the TC74 via its 2-wire I
This device has an address of ‘0b1001101’.
2
C compatible serial port.
A.11
SERIAL EEPROM
A 24L256 (32K x 8) serial EEPROM is included on the board to illustrate I
2
C bus concepts.
A.12 LCD
An LCD display with two lines, 16 characters each, is connecting to the 28 and 40-pin sockets. There are three control lines (RA3:RA1) and four data lines (RD3:RD0).
A 5k Ω pot may be installed into R20 to adjust contrast on the LCD. If this is done, R5 and R6 need to be removed.
DS41584A-page 32
2011 Microchip Technology Inc.
Hardware Detail
A.13 SAMPLE DEVICES
A sample part programmed with a simple program is included in the PICDEM 2 Plus
Demonstration Board kit.
Table A-1 lists the I/O features and port connections for each
processor type.
TABLE A-1: PORT CONNECTIONS
Device LEDs RS-232 S1 S2 S3
Pot
R16
LCD EEPROM Buzzer
18-pin RB3:RB0 N/A MCLR RA4 RB0 RA0 N/A N/A N/A
28-pin RB3:RB0 RC6/RC7 MCLR RA4 RB0 RA0 RC3/RC4 RA3:RA1 RC2
40-pin RB3:RB0 RC6/RC7 MCLR RA4 RB0 RA0 RC3/RC4 RA3:RA1
RD3:RD0
RC2
ICD
Temp
Sensor
Y1/Y2
RB6/RB7 N/A Yes
RB6/RB7 RC3/RC4 Yes
RB6/RB7 RC3/RC4 Yes
2011 Microchip Technology Inc.
DS41584A-page 33
PICDEM™ 2 Plus Demonstration Board User’s Guide
A.14 BOARD LAYOUT AND SCHEMATICS
The following figures show the part layout (silkscreen) and schematics for the PICDEM
2 Plus Demonstration Board.
FIGURE A-1: PICDEM™ 2 PLUS DEMONSTRATION BOARD PARTS LAYOUT
DS41584A-page 34
2011 Microchip Technology Inc.
FIGURE A-2:
Hardware Detail
PICDEM™ 2 PLUS DEMONSTRATION BOARD SCHEMATIC
2011 Microchip Technology Inc.
DS41584A-page 35
PICDEM™ 2 Plus Demonstration Board User’s Guide
FIGURE A-3: PICDEM™ 2 PLUS PIC16F1937 PINOUT
FIGURE A-4: PICDEM™ 2 PLUS PIC18F86K22 PINOUT
DS41584A-page 36
2011 Microchip Technology Inc.
PICDEM™ 2 Plus Demonstration Board User’ Guide
NOTES:
2011 Microchip Technology Inc.
DS41584A-page 37
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support: http://www.microchip.com/ support
Web Address: www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
DS41584A-page 38
Worldwide Sales and Service
ASIA/PACIFIC
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Hangzhou
Tel: 86-571-2819-3180
Fax: 86-571-2819-3189
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Fax: 886-7-330-9305
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
05/02/11
2011 Microchip Technology Inc.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Microchip
:
DM163022-1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement