Declaration of Conformity
Hereby, Sharp Telecommunications of Europe Ltd, declares
that this GX10 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/
EC.
A copy of the original declaration of conformity can be
found at the following Internet address:
http://www.sharp-mobile.com
Alternately contact:
Sharp Telecommunications of Europe Ltd
Azure House,
Bagshot Road,
Bracknell, Berks, RG12 7QY, U.K.
1
Introduction
Introduction
Congratulations and thank you for choosing the GX10.
About This User Guide
This user guide is carefully designed to help you learn
about your phone’s features and operations quickly and
effectively.
NOTICE
• We strongly recommend that you keep separate
permanent written records of all important data. Data
may be lost or altered in virtually any electronic
memory product under certain circumstances.
Therefore, we assume no responsibility for data lost
or otherwise rendered unusable, whether as a result of
improper use, repairs, defects, battery replacement,
use after the specified battery life has expired or any
other cause.
• We assume no responsibility, directly or indirectly,
for financial losses or claims from third parties
resulting from the use of this product and any of its
functions, such as stolen credit card numbers, the loss
or alteration of stored data, etc.
• All company and/or product names are trademarks
and/or registered trademarks of their respective
holders.
• Screen layout illustrated in this user guide may differ
from the actual one.
The information described in this user guide is
subject to change without notice.
• All the functions described in this user guide may not
be supported in all networks.
• We assume no responsibility for downloaded
contents, information, etc. from network.
Copyright
According to copyright laws, the reproduction,
alteration and use of material which is protected by
copyright (music, pictures, etc.) is only permitted for
personal or private use. If the user is not in possession
of more extensive copyright or has not received the
explicit permission from the copyright owner to
reproduce, alter or use a copy which has been made or
modified in this way, this is considered to be a violation
of the copyright laws and gives the copyright owner the
right to claim for damages. For this reason, avoid the
illegal use of material which is protected by copyright.
Windows is a registered trademark of Microsoft
Corporation in the United States and/or other countries.
Powered by JBlend®, ©1997-2002 Aplix Corporation. All
rights reserved.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc.
in the U.S. and other countries.
JBlend and all JBlend-based trademarks and logos are
trademarks or registered trademarks of Aplix Corporation in
Japan and other countries.
In this product, JBlend® is incorporated.
JBlend® is a Java execution environment
that Aplix developed for implementing
advanced performance and fast operation
on small-memory systems. JBlend and
JBlend logo are trademarks or registered
trademarks of Aplix Corporation in Japan
and other countries.
Powered by Mascot Capsule®/Micro3D EditionTM
Mascot Capsule® is a registered trademark of HI Corporation
©2002 HI Corporation. All Rights Reserved.
Licensed by Inter Digital Technology Corporation under one
or more of the following United States Patents and/or their
domestic or foreign counterparts and other patents pending, including U.S. Patents: 4,675,863: 4,779,262:
4,785,450 & 4,811,420.
Introduction
2
Licensed under U.S. Patent 4,558,302 and foreign counterparts.
T9 Text Input is covered by the United Kingdom Pat.
No.2238414B, Euro. Pat. No. 0 842 463 (96927260.8) and
other patents pending.
3
Introduction
Useful functions and services of the
phone
Your phone offers you the following features:
• The built-in digital camera can take pictures.
• Create and read SMS.
• Multimedia Messaging Service (MMS) can
personalise your phone in various ways: you can send
and receive multimedia messages with graphical
images, photographs or sound attached.
• WAP browser helps you to access a variety of
information on the mobile internet.
• You can play with JavaTM applications. You can also
download various kinds of JavaTM applications from
Vodafone via the mobile Internet.
• The maindisplay of colour TFT-LCD makes the
screens clearer, more beautiful and easier to view.
• Sub-Screen allowing you to see who is calling and
new message indicators.
• You can create the various melodies for your original
ringing tones using up to 16 chords.
• Voice memo function allows you to record and play
back your vocal message.
Table of Contents
Introduction ................................................. 1
Useful functions and services of the phone ..3
Table of Contents ........................................ 4
Your Phone .................................................. 7
Accessories ..................................................7
Getting Started ............................................ 8
Inserting the SIM Card and the Battery .....10
Charging the Battery ..................................13
Turning Your Phone On and Off ...............15
Display Indicators ......................................15
Sub-Screen .................................................17
Call Functions ........................................... 19
Making a Call .............................................19
Speed Dialling ............................................19
Redialling ...................................................20
Ending a Call ..............................................20
Answering a Call ........................................20
Incall Menus ...............................................21
Phonebook ................................................. 24
Entering Characters ....................................24
Creating a New Entry .................................25
Finding a Name and Number .................... 28
Editing Phonebook Entries ........................ 28
Deleting Phonebook Entries ...................... 29
Checking Your Own Numbers .................. 29
View Groups .............................................. 29
Memory Status ........................................... 30
Speed Dial List .......................................... 30
Sending Messages ..................................... 31
Using the Menu .......................................... 32
List of Menu Functions ............................. 33
Camera ......................................................34
Using the Timer ......................................... 36
Sending Pictures ........................................ 37
Deleting Pictures ....................................... 37
My Phone .................................................... 38
Java™ ........................................................ 38
My Java™ Games .................................... 39
My Pictures ............................................... 40
My Sounds ................................................ 43
My Bookmarks ......................................... 45
My Text Templates ................................... 46
Table of Contents
4
Memory Status .......................................... 47
Fun & Games ............................................. 48
Java™ Games ............................................48
Other Games ............................................. 51
Melody Editor ...........................................52
Tone Editor ............................................... 59
Profiles ...................................................... 63
Activating a Profile ....................................63
Customising Profiles ..................................63
Resetting Profile Settings ...........................64
Ringer Volume ...........................................64
Ringer Type ............................................... 64
Vibration .................................................... 65
Keypad Tones ............................................65
Warning Tone ............................................66
Power On/Off Sound ................................. 66
Message Alert ............................................67
Low Battery Alert ...................................... 68
Any Key Answer .......................................68
Organiser ................................................... 69
Calculator .................................................. 69
Calendar .................................................... 70
Clock & Alarm ...........................................71
5
Table of Contents
Voice Memo ..............................................75
Help List ....................................................76
Call Manager ..............................................77
Call Log ......................................................77
Call Timers ................................................78
Call Costs ..................................................79
Data Counter .............................................81
Diverts .......................................................82
Settings .......................................................84
Phone Settings ............................................84
Call Settings ...............................................89
Network Settings ........................................93
Internet Settings ........................................94
Infrared ......................................................98
Security .....................................................99
Master Reset ............................................103
Vodafone live! ..........................................104
Viewing the WAP Browser ......................104
Navigating a WAP Page ...........................104
Messages ..................................................106
MMS (Multimedia Messaging Service) ...106
SMS (Short Message Service) .................113
Cell Broadcast .........................................117
Cell Information ......................................118
Data Transmission .................................. 119
System Requirements ...............................119
Software Installation and Setup ...............119
Using the Modem Setup ...........................119
Troubleshooting ...................................... 121
Safety Precautions and Conditions of
Use ............................................................ 123
CONDITIONS OF USE ...........................123
ENVIRONMENT ....................................125
PRECAUTIONS CONCERNING
VEHICLE USE ........................................126
Index ......................................................... 127
Quick Reference ..................................... 132
Table of Contents
6
Your Phone
Please check the following carefully. Your phone
should come complete with:
• GSM 900/1800 GPRS phone
• Rechargeable Li-ion battery
• AC charger
• Hands free
• CD-ROM
• User guide
Accessories (option)
•
•
•
•
Li-ion spare battery (XN-1BT11)
Cigarette lighter charger (XN-1CL10)
Car holder (XN-1CH11)
Data cable (RS232C cable: XN-1DC10)
Some of the above accessories may not be offered by
region.
For details, please contact your dealer.
7
Your Phone
Getting Started
Getting Started
8
1. Earpiece
2. Navigation Keys (Arrow Keys):
Move the cursor to select
menu items, adjust the
earpiece volume, etc.
Up/Down arrow keys: Search the Phonebook
entries in stand-by mode.
Left arrow key:
Adjusts the earpiece
volume in stand-by mode.
Right arrow key:
Displays the Phonebook
menu in stand-by mode.
3. M Key:
Displays the Main Menu
and executes the functions.
4. Left Soft Key:
Executes the function at the
bottom left on the screen.
5. Send Key:
Makes or accepts calls,
views the call in stand-by
mode.
6. Voice Mail Key:
Used to connect to Voice
mail centre. (Depends on
the SIM card.)
7. * /Shift Key:
Used to enter * or switch
the text mode.
8. Main-Screen Display
9
Getting Started
9. Hands free Connector
10. Right Soft Key:
Executes the function at the
bottom right on the screen.
11. End/Power Key:
Ends a call, turns power on/
off.
12. Keypad
13. Microphone
14. External Connector: Used to connect either the
charger or data cable.
15. Aerial
16. Sub-Screen Display
17. Camera
18. Mirror:
For self portraits.
19. LED Indicator
20. Infrared Port:
Sends and receives data via
infrared.
21. Speaker
22. Side Keys
Up/Down keys:
Move the cursor to select
menu items, etc.
23. Battery Cover
Inserting the SIM Card and the
Battery
2. Slide the SIM card into the SIM holder.
1. Slide off the battery cover.
SIM card
Getting Started
10
3. Hold the battery so that the metal contacts of the
battery are facing down, slide the guides on the top
of the battery into the battery slots
, and then
insert it
.
4. Replace the battery cover so that the marks are
aligned and slide it as shown.
Note
• Make sure that only 3V SIM cards are used.
• Use only the approved battery (XN-1BT11).
11
Getting Started
Removing the SIM Card and the Battery
1. Make sure to turn off your phone and disconnect
charger and other accessories. Slide off the battery
cover.
3. Slide the SIM card by pushing the back of the card
and remove it from the SIM holder.
2. Pick up the battery using the protruding edge and
remove the battery from the phone.
Getting Started
12
Battery Disposal
The device is supported by a battery. In order to protect
the environment, please read the following points
concerning battery disposal:
• Take the used battery to your local waste depot,
dealer or customer service centre for recycling.
• Do not expose the used battery to an open flame, into
water or dispose with the household waste.
To Charge Using the Charger
1. Connect the charger to the external socket located at
the bottom of the phone with the charger’s “PUSH
TOP” mark facing towards you, and to an AC
outlet.
LED indicator
Charging the Battery
You must charge the battery for at least 2 hours before
using your phone for the first time.
The LED indicator lights in red.
Standard charging time: Approx. 2 hours.
Note
• Charging time may be longer than above depending
on the state of a battery and a surrounding situation.
(See “Battery” on page 124.)
13
Getting Started
To disconnect the charger
Push and hold the side buttons of the charger, then
disconnect the charger from the external socket of the
phone.
2. When charging is complete, the LED indicator turns
off. Unplug the charger from the AC outlet, then
unplug the charger connector from the phone.
Note
• Do not use any non approved charger, this may
damage your phone and invalidate any warranty,
please see “Battery” on page 124 for details.
• When the phone is charging, the animated battery
status icon (
) will be displayed in the upper right
of the screen.
To Charge Using the Cigarette Lighter Charger
The cigarette lighter charger (option) supplies power
for charging from the cigarette lighter socket of a car.
Battery Level Indicator
The current battery level is displayed in the upper right
hand side of the screen and the Sub-screen.
Low Battery During Use
When the battery is running low, an alarm will sound
and the “
” will appear on the screen and the Subscreen.
If you are using your phone and you hear the “low
battery” alarm, attach your charger as soon as possible.
The phone may not be able to continue normal
operation if you continue to use it. The battery may only
last five minutes before the phone itself powers down
during a call.
Charge Level
Indicators
Full level (greater than 60%)
Partial level (less than 60%)
Partial level (less than 30%)
Low level (less than 10%)
Empty
Charging the battery is
recommended.
Charge the battery.
Getting Started
14
Turning Your Phone On and Off
To turn the power on, press and hold
approximately 2 seconds.
The stand-by screen appears.
To turn the power off, press and hold
approximately 2 seconds.
Display Indicators
for
Status
Indicators
for
Entering the PIN Code
If activated you will be asked to enter a PIN (Personal
Identification Number) code after turning on your
phone.
1. Enter your PIN code.
.
2. Press
Note
• If your PIN code is entered incorrectly three times in
a row, the SIM card is locked. See “Enabling/
Disabling the PIN Code” on page 99.
15
Getting Started
Left
softkey
Right softkey
1.
2.
/
:
:
3.
/
/
Indicates the strength of received
signal/the service is out of range.
11.
Appears when in call.
12.
:
Appears when your phone is in data
communication mode.
13.
:
Appears when your phone is in fax
communication mode.
/
:
Indicates the input mode (Upper case
only the first letter of the word mode/
Upper case mode/Lower case mode/
Numeric mode).
Appears when your phone is roaming
outside of your network.
14.
:
Appears when your phone is GPRS
enabled and within range.
Flashes during GPRS transmission.
15.
:
Appears when Alarm is set.
4.
:
5.
/
/
6.
/
:
Appears when viewing secured WAP
browser.
17.
:
Appears when the data cable is
connected to your phone.
7.
/
:
Appears when a picture or image/
sound is attached to MMS.
18.
:
Appears when “Ringer Volume”
(p. 64) is set to “Silent”.
8.
:
Indicates a Phonebook entry stored in
the phone memory.
19.
:
Appears when Vibration alert is set.
9.
:
Indicates a Phonebook entry stored on
the SIM card.
10.
Appears when the T9 text input mode
is activated.
:
:
: Appears when a new SMS, MMS
Alert or WAP Alert has arrived.
16.
:
Appears when “Diverts” (p. 82) is set
to “All Calls”.
Indicates the battery level.
Getting Started
16
20. (No display)/
21.
:
22.
23.
24.
/
/ / :
Indicates the phone’s mode (Normal
mode/Meeting mode/Activity mode/
Car mode/Silent mode).
Status Indicators
Status
Indicators
Appears when a voicemail message is
stored.
:
/
/ :
Appears when up, down, right or left
navigation is available.
:
Appears when “Infrared” is on/during
connection.
1.
:
Indicates the received signal strength.
2.
:
Appears when GPRS is within range
and can be used.
Flashes during in GPRS
communication mode.
3.
:
Appears when a new SMS, MMS
Alert or WAP Alert has arrived.
:
Indicates the battery level.
Appears when the JavaTM application
is executed/suspended.
Softkey Indicators
To execute the operation indicated, press each
corresponding key.
25. Area at the lower left of a screen:
Displays the operation executed by
left softkey.
26. Area at the lower right of a screen:
Displays the operation executed by
right softkey.
17
Sub-Screen
Getting Started
4.
:
Appears when Alarm is set.
5.
6.
/
7.
:
:
Appears when “Infrared” is on/during
connection.
Appears when “Diverts” (p. 82) is set
to “All Calls”.
8.
:
Appears when the data cable is
connected to your phone.
9.
:
Appears when “Ringer Volume”
(p. 64) is set to “Silent”.
Getting Started
18
Call Functions
Making a Call
1. Enter the area code and the phone number you wish
to dial.
If you enter the wrong number, press
[Clear] to
delete the number to the left of the cursor.
to dial.
2. Press
Emergency Calls
1. Enter 112 (international emergency number) using
the keypad.
to dial.
2. Press
Note
• Emergency calls may not be available on all mobile
phone networks when certain network services and/
or phone features are in use. Contact your network
operator for more information.
• This Emergency number can normally be used to
make an emergency call in any country, with or
without a SIM card inserted, if a GSM network is
within range.
19
Call Functions
International Calls
until a “+” (international
1. Press and hold
dialling prefix) sign appears.
2. Enter the country code, followed by the area code
and the number.
3. Press
to dial.
Note
• Enter the area code omitting the first 0 when making
international calls, in most cases. (It differs for some
countries.)
Speed Dialling
In the Speed Dial List, up to 9 phone numbers out of the
Phonebook can be set. You can call the numbers using
the digit keys (
to
and
).
For details on setting the Speed Dial List, see “Speed
Dial List” on page 30.
to
1. Press and hold any of the digit keys (
and
).
The phone number stored in the Speed Dial List is
displayed, then dialled.
Redialling
5. Select “On” to enable the Auto Redial function or
You can redial the numbers in the call log list that you
may have missed, received or dialled. Each list can
contain up to 10 numbers.
during stand-by.
1. Press
or
to select a category between
2. Press
“Dialled Numbers”, “Missed Calls” and “Received
Calls”.
Note
• When you receive an incoming call, the Auto Redial
function will be interrupted.
• Automatic redialling is not available for fax and data
calls.
3. Select the number you wish to call by pressing
or
to redial the call.
Automatic Redialling
This setting allows you to automatically redial the
number if the first attempt was unsuccessful.
If you wish to stop redialling, press
or
[End].
To Set the Auto Redial Function
to display the Main Menu.
1. Press
or
to select “Settings”, then press
2. Press
3. Press
.
or
to select “Call Settings”, then press
or
to select “Auto Redial”, then press
.
4. Press
.
Ending a Call
1. Press
.
4. Press
“Off” to disable it, then press
to end the call.
Answering a Call
When an incoming call is detected, the phone rings and
the LED indicator flashes green.
1. Open your phone.
to answer the call.
2. Press
or
Press any key except
,
[Reject],
and
when the “Any Key Answer” function is enabled.
Set the Any Key Answer function in the profile in
each mode. (p. 68)
.
Call Functions
20
Tip
• When the hands free kit is connected to the phone,
you can answer calls by pressing the Side keys (up or
down).
• If you have subscribed to the Calling Line
Identification (CLI) service and the caller’s network
sends the number, the caller’s number will appear on
the screen. If the caller’s name and number are
stored in the Phonebook, the caller’s name will
appear on the screen.
• If the number is a restricted number, the display
shows “Withheld”.
• When receiving a call from the person whose picture
is registered in the Phonebook, receiving display and
the picture are displayed alternately.
Rejecting an Incoming Call
You can reject a call you do not wish to answer.
or
[Reject] or press and hold the Side
1. Press
keys (up or down) whilst the phone is ringing.
Incall Menus
Your phone has additional functions available whilst a
call is in progress.
21
Call Functions
Adjusting the Earpiece Volume
You can adjust the earpiece volume during a call.
.
1. During a call, press
to increase the earpiece volume or press
2. Press
to decrease the earpiece volume.
Each press of
or
adjusts the earpiece volume
by one of 5 levels.
[OK].
3. Press
Tip
• You can also adjust the earpiece volume using the
Side keys (Volume up key or Volume down key)
during a call.
Putting a Call on Hold
This function allows you to manage two calls at the
same time. If you wish to make another call whilst you
are talking to someone, you can put the current call on
hold to call someone else.
To make another call during a call
[Options] to display the
1. During a call, press
Options Menu.
.
2. Select “Hold”, then press
The current call is put on hold.
To retrieve a call, press
[Options] and
select “Retrieve”, then press
.
3. Enter the phone number you wish to make another
call to, then press
.
Tip
• You can also make another call by entering the phone
number during a call instead of steps 1 and 2. The
current call is automatically put on hold.
Call Waiting
This service notifies you of another incoming call
whilst you have a call in progress.
[Answer] to answer the
1. During a call, press
second call.
The first call is put on hold and you can now talk to
the second caller.
[Options] and select “Swap” to switch
2. Press
between the two calls.
3. Press
[Options] and select “End Call”,
then press
to end the current call and return to
the held call.
Note
• You need to set “Call Waiting” to “On” if you use
Call Waiting service (p. 89).
• Call Waiting service may not be available on all
networks. Contact your network operator for more
information.
• If you do not wish to answer the second call, press
[Reject] in step 1. The call log of the second call
will be saved as a missed call.
Conference Call
Conference call is a call with more than 2 participants.
You may include up to 5 participants in a conference
call.
Making a Conference Call
To make a conference call, you must have one active
call and one held call.
[Options] to display the Options Menu.
1. Press
or
to select “Multiparty”, then press
2. Press
.
3. Press
or
to select “Join All”, then press
to join the conference call.
4. Press
to end the conference call.
Note
• Conference call service may not be available on all
networks. Contact your network operator for more
information.
Call Functions
22
[Options] to display the Options Menu.
To Have a Private Conversation with one of the
participants
If you wish to have a private conversation with one of
the participants, you may select the participant from the
conference list and put the other participants on hold.
1. During the conference call, select the person that
you wish to talk to by pressing
or
.
[Options] to display the Options Menu.
2. Press
or
3. Press
Adding New Participants to the Conference Call
[Options] to display the Options Menu.
1. Press
or
to select “Dial”, then press
.
2. Press
3. Enter the number you wish to include in the
conference call.
4. Press
5. Press
6. Press
to dial.
to select “Multiparty”, then press
7. Press
or
to select “Join All”, then press
to join the conference call.
If you wish to add other participants, repeat steps 1
to 7.
To End the Call with a Conference Call Participant
1. During a conference call, select the person who you
wish to disconnect the call by pressing
or
.
[Options] to display the Options Menu.
2. Press
3. Press
or
to select “End Call”, then press
.
23
or
to select “Multiparty”, then press
.
.
Call Functions
or
to select “Private”, then press
.
4. Press
5. Once you have finished the private conversation,
press
[Options] and select “Multiparty”,
then press
.
6. Press
or
to select “Join All”, then press
to return to the conference call.
Muting the Microphone
[Mute] to mute the
1. During a call, press
microphone.
To unmute the microphone, press
[Unmute].
Phonebook
Key
Lower Case
Characters
Upper Case Characters
Numeric
You can store the phone numbers and E-mail addresses
of your friends, family and colleagues in the
Phonebook.
DEF3ÉÊÈË
def3éêèë
3
GHI4Í Î Ì Ï
ghi4í î ì ï
4
Group name (p. 26)
You can classify the phone numbers and names stored in
the Phonebook, such as “Family” and “Business”.
JKL5
jkl5
5
MNO6ÕÓÔÒÖØÑ
mno6õóôòöøñ
6
Entering Characters
PQRS7
pqrs7ß
7
When entering characters to create Phonebook entries,
SMS or MMS, etc., press the corresponding keys.
TUV8ÚÜÙÛ
tuv8úüùû
8
WXYZ9ÝÞ
wxyz9ýþ
9
Table of Characters
Pressing each key scrolls characters in the following
order.
(space)+ = < >
*+P?
Note:
• Depending on the type of the data entry screen,
usable characters are limited.
Normal Mode
Key
Upper Case Characters
Lower Case
Characters
(space)
-
,: Press and hold to enter 0 - 9 numbers.
Numeric
. (full-stop) , (comma) - (hyphen) ? !
’ (apostrophe) @ _ ( ) / ” :1
1
ABC2ÃÁÀÂÄÅÆÇ
2
abc2ãáàâäåæç
0
£ $ ¥ % &0
:
Press and hold to shift to Sentence mode,
Capital letter, Small letter, Numeric.
:
Press and hold to shift between Normal
and T9 mode.
Phonebook
24
Changing the Input Mode
To change the input mode, press
approximately 2 seconds.
for
T9 Text Input
T9 text input method is a shortcut to enter text easily
and quickly.
until “ ” is displayed.
1. Press and hold
2. Press each key once for any letter you require on
that key.
To enter the word “How”, press
.
or
until the correct word is shown if
3. Press
the character combination, that was initially
displayed, is not correct.
4. Press
to select the word.
Note
• If the correct word is not shown in step 3, enter the
correct word again after switching to the normal
input mode.
Tip
• If you press
instead of step 4, a space is
inserted next to the selected word.
Symbols and Punctuation
To enter symbols or punctuation, press
25
Phonebook
.
Using Text Template
You can use the sentences registered in My Text
Templates when entering characters.
For details on creating the text template, see “Adding
Phrases to My Text Templates” on page 46.
[Options] to display the Options Menu.
1. Press
or
to select “Insert Template”, then
2. Press
press
.
3. Select a desired text template by pressing
or
, then press
.
The selected text template will be inserted.
Creating a New Entry
You can choose either the phone (up to 500) or SIM
card memory locations to store the new entry.
The amount of phone numbers that you can store to the
SIM card is dependant on its capacity. Contact your
network operator for SIM details.
Phonebook Memories
Select the location for storing the Phonebook memory
before storing a new entry.
to display the Phonebook menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
or
to select “Save Nos. to”, then press
.
4. Select “SIM Card” to store the entry on the SIM
memory or “Phone Memory” by pressing
or
, then press
.
When selecting “Choice”, you can choose SIM card
or phone memory every time you store a new
Phonebook entry.
Storing Names and Numbers
to display the Phonebook menu.
1. Press
or
to select “Add New Name”, then
2. Press
press
.
3. If you select “Choice” in step 4 in “Phonebook
Memories”;
Select “SIM Card” or “Phone Memory” by pressing
or
, then press
.
The name entry prompt appears.
.
4. Enter a name, then press
For details on entering characters, see “Entering
Characters” on page 24.
The phone number prompt appears.
.
5. Enter the phone number, then press
Up to 40 digits can be entered.
6. Select a desired number type by pressing
then press
or
,
.
7. Press
[Save].
You can divide the phone numbers of the
Phonebook into groups. You can also register Email address, personal data, and picture/image data.
(See “Storing Optional Data”for details.)
Storing Optional Data
You can store optional data after entering a phone
number. (See “Storing Names and Numbers” for
details.)
Note
• E-mail address, personal data, and picture/image
data cannot be stored on the SIM card.
Selecting Group Name
or
to highlight the right side of
1. Press
“
”, then press
.
or
,
2. Select a desired group name by pressing
then press
.
You can set to display the available group names
when you store/edit the Phonebook, see “View
Groups” on page 29.
Phonebook
26
Entering E-mail Address
or
to highlight the right side of
3. Press
“
”, then press
.
9. Specify the range for displaying the picture/image
4. Enter the E-mail address, then press
Note
• The stored picture/image is automatically saved
under the “in Phonebook” section of the Saved
Pictures.
• The picture/image cannot be deleted in the Saved
Pictures. Remove the picture/image data from the
Phonebook.
by pressing
10. Press
.
Up to 60 characters can be entered.
Entering Personal Data
or
to highlight the right side of
5. Press
“
”, then press
.
6. Enter the personal data, then
.
Up to 60 characters can be entered.
Storing Picture/Image Data
You may store a picture/image for use with the
Phonebook.
When you receive a call from a person with a
Phonebook entry which also has a linked picture/image,
when the person calls, the linked picture/image will be
displayed.
or
to highlight the right side of
7. Press
“
”, then press
.
8. Select the desired picture/image, then press
The selected picture/image will appear on the
screen.
27
Phonebook
.
,
,
or
, then press
.
[Save].
Adding the Phone Number from the Call Log
Entries
1. Display the call log entry you wish to store (p. 77).
.
2. Press
3. Press
press
or
.
to select “Save to Phonebook”, then
4. Follow the procedure from step 3 in “Storing Names
and Numbers” on page 26.
Storing after Inputting a Phone Number
[Save].
1. Enter the phone number, then press
2. Follow the procedure from steps 3 to 7 in “Storing
Names and Numbers” on page 26.
Finding a Name and Number
Two methods of searching through the Phonebook are
available:
Search by Name
to display the Phonebook menu.
1. Press
.
2. Select “View Names”, then press
3. Enter a name or the first character(s) of the name.
Matched results will be displayed alphabetically.
If there is no entry in the Phonebook that satisfies
the exact search criteria, the name that is nearest
alphabetically matching will be displayed.
or
to select
4. Scroll through list by pressing
the desired name, then press
[Select].
The detailed screen of the Phonebook appears.
.
5. Press
6. Press
or
then press
to select the desired phone number,
to dial.
Tip
• If you press
and select “Search” after step 2, you
can also search the name and number.
• You can also dial the desired phone number by
pressing the digit key corresponding to the list
number instead of step 6.
Search in Alphabetical Order
or
whilst in stand-by to open the
1. Press
Phonebook.
or
to find the
2. Scroll the list by pressing
desired name.
3. If you wish to do a name search, perform steps 3 and
4 in “Search by Name”.
Editing Phonebook Entries
You can edit Phonebook entries.
1. Search for the desired Phonebook entry.
For details on searching through Phonebook entries,
see “Finding a Name and Number” .
.
2. Press
or
to select “Edit”, then press
.
3. Press
4. Select an entry you wish to change by pressing
or
, then press
[Edit].
Phonebook
28
5. Edit entry as required.
.
6. Press
3. Press
If you wish to edit another item, repeat steps 4 to 6.
[Save] to save the change(s).
7. Press
Deleting Phonebook Entries
1. Search for the desired Phonebook entries.
For details on searching through Phonebook entries,
see “Finding a Name and Number” on page 28.
.
2. Press
or
to select “Delete”, then press
3. Press
.
4. Select “Yes”, then press
Note
• “Data” or “Fax” may not be displayed depending on
SIM card.
Editing Your Phone Numbers
1. Perform steps 1 to 3 in “Checking Your Own
Numbers”.
.
2. Press
.
3. Press
The selected entry will be deleted.
To cancel deletion, select “No” at step 4, then press
.
4. Press
Checking Your Own Numbers
You can check and edit your own voice, data and fax
phone numbers in the Phonebook.
to display the Phonebook menu.
1. Press
or
to select “Own Numbers”,
2. Press
then press
.
29
or
to select the phone number you
wish to check from either “Voice”, “Data” or “Fax”,
then press
.
Phonebook
[Clear] to erase the phone number and
enter a new phone number.
to save the phone number.
View Groups
You can set the available group names when you store/
edit the Phonebook.
to display the Phonebook menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Select “View Groups”, then press
.
4. Select a desired group name by pressing
.
“ ” indicates that the group has been selected.
To cancel the selected group, press
again.
The checkbox becomes blank again.
Memory Status
This function helps you to check the number of entries
stored in the Phonebook.
to display the Phonebook menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
press
or
.
to select “Memory Status”, then
You can check the following memory status.
“SIM Card : xxx/xxx”
“Speed Dial : xx/xx”
“Phone
: xxx/500”
Note
• The number of locations available on the SIM is
dependant on its capacity.
Speed Dial List
You can set a maximum of 9 phone numbers to the
Speed Dial List.
Use the phonebook entries on the SIM card.
Adding Phonebook entries to the Speed Dial
List
1. Search for the desired Phonebook entries.
For details on searching through Phonebook entries,
see steps 1 to 4 in “Search by Name” on page 28.
or
to select the phone number.
2. Press
3. Press
4. Press
.
or
to select “Add to Speed”, then press
.
5. Select the number you wish to add by pressing
or
, then press
.
Viewing the Speed Dial List
to display the Phonebook menu.
1. Press
or
to select “Settings”, then press
2. Press
.
3. Press
or
to select “Speed Dial List”, then
press
.
The stored names and phone numbers in the
selected entry are displayed in order.
Phonebook
30
Sending Messages
1. Search for the desired Phonebook entries.
For details on searching through Phonebook entries,
see steps 1 to 4 in “Search by Name” on page 28.
or
to highlight the right side of
2. Press
“
”, “
” or “
”, then press
or
Press
or
to highlight the right side of
“
”, then press
.
3. Press
or
to select “Send Message”, then
press
.
If you highlight the right side of “
”, “
” or
“
” in step 2:
or
to select “MMS” or “SMS”, then
4. Press
press
.
5. Enter your message.
For details on creating a message, see “Creating a
New MMS” on page 106 or “Creating a New SMS”
on page 114.
31
Phonebook
Using the Menu
Using the Main Menu
during stand-by mode.
1. Press
or
to navigate to required location.
2. Press
3. Press
or
to access function.
To Select Another Item within the Main Menu
To return to the previous screen after selecting a
function from the Main Menu or Sub Menu, press
.
Every time you press
, the screen goes back one by
one.
Example: To access “Language” Sub Menu using
shortcut keys
Press
.
Note
• The shortcut keys work for the first three menu levels
only.
Side Keys
The Side keys (up or down) function the same as
pressing
or
.
Operation Guidance
Your phone uses softkeys to help you to navigate the
phone (
and
). These keys change usage
depending on the situation. The function of each
softkey at any given time is highlighted at the bottom
left and bottom right of the screen.
Shortcut Keys
When pressing several key combinations during standby mode, you can shortcut to the specified menus.
To access the desired menu directly, press
and digit
keys for the menu’s corresponding number during
stand-by mode. See the following table as reference.
Using the Menu
32
List of Menu Functions
Menu No./
Main Menu
Menu No./
Sub Menu1
Menu No./
Main Menu
7 Settings
1 Camera
2 My Phone
3 Fun & Games
4 Profiles
5 Organiser
6 Call Manager
33
Using the Menu
1
2
3
4
5
6
My JavaTM Games
My Pictures
My Sounds
My Bookmarks
My Text Templates
Memory Status
1
2
3
4
1
2
3
4
5
1
2
3
4
5
1
2
3
JavaTM Games
Other Games
Melody Editor
Tone Editor
Normal
Meeting
Activity
Car
Silent
Calculator
Calendar
Clock & Alarm
Voice Memo
Help List
Phonebook
Call Register
Diverts
8 Vodafone live!
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
Menu No./
Sub Menu1
Phone Settings
Call Settings
Network Settings
Internet Settings
Infrared
Security
Master Reset
Vodafone live!
New
Chat
Games
Find & Seek
News
Sport
Shopping
Search
1
2
3
4
5
6
MMS
SMS
Cell Broadcast
Cell Info
Vodafone Messenger
Vodafone Mail
9 Info-Service*
0 Messages
* Depends on the contents of SIM card.
Camera (M 1)
4. Press
Your phone incorporates an integrated digital camera.
This allows you to take and send pictures wherever you
are.
Tip
• To leave Camera Mode without registering the taken
picture after step 2 in “Taking Pictures”:
Press
and select “Yes”, then press
.
• To take a picture of yourself, press
or the Side
keys (up or down) whilst checking the image reflected
on the mirror on the back of the phone. Place/Hold
the phone at least 40 cm away from yourself.
Taking Pictures
Put the phone into the camera mode to take a picture.
You can send the pictures registered in the Saved
Pictures with your message.
for approximately 2 seconds
1. Press and hold
whilst stand-by.
The phone switches to the camera mode.
The camera view can be seen through the “on
screen” viewer.
or the Side keys (up or down) to take the
2. Press
picture.
The shutter sound occurs and the static image of the
taken picture is displayed.
[Save].
3. Press
“Save to My Phone” is displayed, then the picture is
registered.
If you send a picture by MMS after taking the
picture, press
in step 3.
The camera returns to step 1 repeat process as
desired.
to return to stand-by.
Using the Zoom Function
Press
[Zoom] to magnify the photographic subject.
Press
[Wide] to restore the original magnification.
Note
• When “Select Picture Size” is set to “Large”, you
cannot use the zoom function.
To select the picture size
[Options] before step 2 in “Taking
1. Press
Pictures” to display the Options Menu.
or
to select “Select Picture Size”, then
2. Press
press
.
3. Select the picture size by pressing
press
or
, then
.
Camera
34
To select the mode
[Options] before step 2 in “Taking
1. Press
Pictures” on page 34 to display the Options Menu.
or
to select “Select Mode”, then press
2. Press
.
3. Select the mode by pressing
or
, then press
.
Note
• Vertical stripes may be reflected to a picture by light
source. Change the mode in this case.
In the Case of No Available Memory
When the number of pictures that can be taken becomes
5 or less, or when the remaining capacity becomes 27.5
Kbytes (when “Medium” is selected as the picture size)
or less, “ ” will appear on screen. The screen returns
to step 2 in “Taking Pictures” on page 34. The number
of pictures that can be taken is displayed in the upper
left of the screen. (The number of pictures that can be
taken is approximate.)
When the number of pictures that can be taken becomes
0, and when you try to take a picture again, “Can not
take a picture. Maximum Capacity” is displayed.
Retaking Pictures
After steps 1 and 2 in “Taking Pictures” on page 34,
press
[Back].
Further shooting is available.
Meanings of Indicators in Camera Mode
Delay timer indicator (p. 36)
Note
• The Digital Camera Uses a C-MOS Sensor. Although
this camera has been manufactured to the highest
specification, some pictures may still appear too
bright or too dark.
• If the phone has been left in a warm place for a long
time before taking or registering a picture, the
picture quality may be poor.
: Bright
:
: Normal
:
: Dark
Picture size indicators (p. 34)
Large:
288 × 352 dots
Medium (default): 120 × 160 dots
Small:
60 × 80 dots
35
Camera
: Whilst the timer setting is on.
Picture brightness indicators (p. 36)
Mode indicator (p. 35)
: Mode 1
: Mode 2
Making Adjustments According to Lighting
Conditions
Adjusting the Brightness of the Picture
Adjust the brightness of the picture by pressing
or
.
Once the phone has returned to the stand-by screen the
brightness settings return to default.
Viewing the Taken Pictures
The taken pictures can be viewed in the Saved Pictures.
[Options].
1. In camera mode, press
The Options Menu is displayed.
.
2. Select “Existing Pictures”, then press
The list of Saved Pictures is displayed.
3. Select the file name you wish to view by pressing
or
, then press
.
The selected picture is displayed.
[Back] to return
4. Once you have finished, press
to the list.
Tip
• Your pictures are given file names which show the
time and date when the picture was taken.
Example:
The file name “13-05-02_12-34-56” is displayed for
the picture taken at 12:34:56 of 13th May 2002. The
file names of your pictures can be changed (p. 41).
Using the Timer
Taking a Picture with the Timer
[Options].
1. In camera mode, press
The Options Menu is displayed.
or
to select “Delay Timer”, then press
2. Press
.
3. Press
or
to select “On”, then press
.
“
” appears on the screen and the phone returns
to camera mode.
to take the picture.
4. Press
Delay timer begins.
10 seconds after the timer sound occurs, the camera
takes a picture, and sounds a tone.
Camera
36
Note
• Whilst the delay timer is operating, the LED
indicator and the icon flash.
• If
is pressed whilst the delay timer is operating,
the picture is taken instantly.
• If there is an incoming call or alarm functioning,
or
is pressed, whilst the delay timer is
operating, the camera operation is cancelled. In this
case, the timer setting is cancelled.
• The zooming function with
[Zoom] / [Wide], or
the adjustment of brightness of the picture with
or
, is unavailable whilst the delay timer is
operating.
Cancelling the Delay Timer
[Options] whilst the delay timer setting is
1. Press
on.
The Options Menu is displayed.
or
to select “Delay Timer”, then press
2. Press
.
3. Press
“
37
or
to select “Off”, then press
” goes off.
Camera
.
Sending Pictures
See “Sending Messages” on page 42 for instructions.
Deleting Pictures
See “Deleting Pictures/Images” on page 42 for
instructions.
My Phone
Downloading JavaTM Applications
My Phone contains several types of picture/image and
sound data along with JavaTM applications which can
be controlled collectively. Also included in My Phone
are frequently used text message phrases and accessed
WAP pages (addresses) which you can use and edit.
Confirmation screen
Before downloading the JavaTM application you will be
asked to confirm what you are about to receive.
After checking the information on the confirmation
screen, the JavaTM application can be downloaded.
Java™
Using JavaTM Applications
Various kinds of Vodafone specific JavaTM
applications can be used in this phone.
To use JavaTM applications, download the JavaTM
applications via the mobile Internet.
Some JavaTM applications offer the ability to connect to
a network either within a game or network based
application.
Note
• JavaTM applications may be both localised (no
connectivity) and network based (using the mobile
Internet to update information/play games). The
network may charge you more for using networkbased applications. Please contact your service
provider for more information.
Note
• User authentication might be required before
downloading the application on some information
screens.
Download
1. Press
2. Press
to display the Main Menu.
or
to select “My Phone”, then press
.
.
3. Select “My JavaTM Games”, then press
or
to select “Download More”, then
4. Press
press
.
The JavaTM application download site is displayed.
5. Select the JavaTM application you wish to
download.
After a WAP browser is displayed variously, the
confirmation screen will appear after a whilst.
My Phone
38
6. Press
[Get].
Downloading starts.
[OK] even if it carries out complete.
7. Press
My Java™ Games (M 2-1)
Along with the preloaded JavaTM application,
downloaded applications are stored in the Saved
Games.
Your phone has one preloaded JavaTM application.
Note
• The phone can store approximately 700Kbytes of
information across the Saved Games, Saved Pictures
and Saved Sounds. The Saved Games can store up to
50 applications.
Executing JavaTM Applications
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
3. Select “My JavaTM Games”, then press
.
4. Select “Saved Games”, then press
The list of Saved Games is displayed.
The downloaded JavaTM applications are
sequentially displayed from the latest one.
39
My Phone
.
5. Select the title of the JavaTM application you wish to
execute by pressing
or
, then press
.
The selected JavaTM application is executed.
When using network connection type JavaTM
applications, connection to the network can be
selected.
To end the JavaTM application
.
1. Press
2. Press
or
to select “End”, then press
The screen returns to stand-by screen.
.
To suspend the JavaTM application
.
1. Press
2. Press
or
to select “Suspend”, then press
.
To resume the JavaTM application, press
during
stand-by screen and select “Resume”, then press
.
Checking the Information of the JavaTM
Application
1. Perform steps 1 to 4 in “Executing JavaTM
Applications”.
2. Select the JavaTM application you wish to check,
then press
[Options].
The Options Menu is displayed.
3. Select “File Information”, then press
.
The detailed information screen is displayed.
or
to scroll through the screen.
4. Press
5. When you have finished, press
[Back] twice.
The screen returns to the Saved Games.
Deleting JavaTM Applications
1. Perform steps 1 to 4 in “Executing JavaTM
Applications” on page 39.
2. Select the JavaTM application you wish to delete,
then press
[Options].
The Options Menu is displayed.
or
to select “Delete”, then press
.
3. Press
4. Select “Yes”, then press
.
The selected application is deleted.
To cancel deletion, select “No” at step 4, then press
.
Note
• You cannot delete preloaded JavaTM applications.
My Pictures (M 2-2)
Pictures that are taken by a digital camera or images
that are downloaded from mobile Internet sites can be
managed.
: This is the folder where the pictures/images
registered in the Phonebook are saved.
: Images in PNG format
: Pictures/Images in JPEG format
: e-Animation file (NEVA)
: Images in GIF format
: Images in BMP format
: Images in WBMP format
: Images in WPNG format
The date and time when the photo was taken is
displayed as a file name for the picture.
Downloading Picture/Image File
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
.
3. Select “My Pictures”, then press
4. Select “Download More”, then press
.
The picture/image file download site is displayed.
My Phone
40
Viewing Pictures/Images
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
.
3. Select “My Pictures”, then press
.
4. Select “Saved Pictures”, then press
The list of Saved Pictures is displayed.
5. Select the file name you wish to view by pressing
or
, then press
.
The selected picture/image is displayed.
6. Once you have confirmed the picture/image, press
[Back] to return to the Saved Pictures.
Checking the Picture/Image Data
Select the desired data in step 5 in “Viewing Pictures/
Images”, then select “File Information” after pressing
[Options] to display the Options Menu.
The file type and size of the selected picture/image are
displayed. Whether the picture/image can be copied,
forwarded, or saved is also displayed.
To return to the Saved Pictures, press
[Back] twice.
41
My Phone
Changing the File Name
1. Perform steps 1 to 4 in “Viewing Pictures/Images”.
2. Select the file name you wish to change by pressing
or
, then press
[Options].
The Options Menu is displayed.
.
3. Select “Rename”, then press
4. Enter a new file name.
To correct the last character, press
[Clear]
briefly.
Press and hold
[Clear] to clear all characters.
.
5. Press
Note
• Following characters cannot be used for a file name:
/, \, :, *, ?, ", <, > and . (full-stop).
Adjusting the Size of the Picture/Image
The pictures/images that are registered in the Saved
Pictures can be adjusted for use as a wallpaper during
stand-by or as an incoming call display.
When the picture/image size is modified, the data size
is updated.
1. Perform steps 1 to 4 in “Viewing Pictures/Images”.
2. Select the file name you wish to adjust by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Adjust Size”, then press
.
3. Press
4. Select the picture/image size you wish to change by
pressing
or
, then press
.
5. Specify the range for displaying the picture/image
by pressing
,
,
or
then press
.
.
6. Press
To cancel registration, press
[Back] at any time
before step 6.
Note
• “Adjust Size” may not be available depending on the
picture/image original and copyright issued.
Sending Messages
1. Perform steps 1 to 4 in “Viewing Pictures/Images”
on page 41.
2. Select the file name you wish to send by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Send Message”, then
3. Press
press
.
4. Enter your message.
For details on creating a message, see “Creating a
New MMS” on page 106.
Note
• Pictures/images with a red icon cannot be sent
attached to a message.
Deleting Pictures/Images
1. Perform steps 1 to 4 in “Viewing Pictures/Images”
on page 41.
2. Select the file name you wish to delete by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Delete”, then press
.
3. Press
4. Select “Yes”, then press
.
The selected picture/image is deleted.
To cancel deletion, select “No” at step 4, then press
.
My Phone
42
My Sounds (M 2-3)
The ring tones instead created by Melody Editor and the
WAVE data recorded by Voice Memo are managed in
the Saved Sounds. Default ring tones are not contained.
: Sound file in SMAF format
: Original ringing tone (composed in Melody
Editor)
: Sound file in Standard MIDI format
: Sound file in i Melody format
: Sound file in WAVE format
Note
• SMAF (Synthetic music Mobile Application Format)
is a format of music data for mobile phones.
Downloading Sound Files
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
.
3. Select “My Sounds”, then press
4. Select “Download More”, then press
.
The sound file downloaded site is displayed.
43
My Phone
Playing Back Sounds
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
.
3. Select “My Sounds”, then press
.
4. Select “Saved Sounds”, then press
The Saved Sounds is displayed.
5. Select the sound you wish to play back by pressing
or
, then press
.
The selected sound is played.
To stop playing, press
[Stop].
Checking the Sound Data
Select the desired sound as in step 5 in “Playing Back
Sounds”, then select “File Information” after pressing
[Options].
The file type and size of the selected sound are
displayed. Whether the sound can be copied, forwarded
or saved is also displayed.
To return to the Saved Sounds, press
[Back] twice.
Changing the File Name
1. Perform steps 1 to 4 in “Playing Back Sounds” on
page 43.
2. Select the file name you wish to change by pressing
or
, then press
[Options].
The Options Menu is displayed.
.
3. Select “Rename”, then press
4. Enter a new file name.
To delete the last character, press
[Clear]
briefly.
Press and hold
[Clear] to clear all characters.
.
5. Press
Note
• Following characters cannot be used for a file name:
/, \, :, *, ?, ", <, > and . (full-stop).
Tip
• When “Data Edit” is displayed in the menu in step 2,
you are able to edit the sound (p. 57). Once you have
completed editing the newly saved file overwrites the
old file. This new file then becomes the original ring
tone.
Setting the Tone and Strength
1. Perform steps 1 to 4 in “Playing Back Sounds” on
page 43.
2. Select the file name you wish to edit by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Tone Set” or “Strength
3. Press
Set”, then press
.
For full details, see pages 55 to 57.
Note
• If “Tone Set” and “Strength Set” are not displayed
in the menu in step 2, you cannot change the settings.
Sending Messages
1. Perform steps 1 to 4 in “Playing Back Sounds” on
page 43.
2. Select the file name you wish to send by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Send Message”, then
3. Press
press
.
If you select your original ringing tone in step 2;
or
to select the file format “SMAF”,
4. Press
“MIDI” or “i Melody”, then press
.
My Phone
44
5. Enter your message.
For details on creating a message, see “Creating a
New MMS” on page 106.
Note
• Sounds with a red icon cannot be sent attached to a
message.
• Only the first part of the data will be converted if you
select “i Melody” in step 4.
Deleting Sounds
1. Perform steps 1 to 4 in “Playing Back Sounds” on
page 43.
2. Select the file name you wish to delete by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Delete”, then press
.
3. Press
4. Select “Yes”, then press
.
The selected sound has been deleted.
To cancel deletion, select “No” at step 4, then press
.
45
My Phone
My Bookmarks (M 2-4)
You can store desired (or frequently used) pages
(addresses) in My Bookmarks. It can save your time in
accessing WAP pages sites.
Adding a Bookmark
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
3. Press
or
to select “My Bookmarks”, then
press
.
The list of My Bookmarks is displayed.
[Options] to display the Options Menu.
4. Press
When you add a bookmark for the first time, press
[Add] instead, then skip to step 6.
or
to select “Add”, then press
.
5. Press
6. Enter the bookmark title, then press
7. Enter the URL address, then press
.
.
Accessing Bookmarked Pages
1. Perform steps 1 to 3 in “Adding a Bookmark”.
2. Select a bookmarked page you wish to access by
pressing
or
, then press
.
Editing Bookmarks
1. Perform steps 1 to 3 in “Adding a Bookmark” on
page 45.
2. Select the desired bookmark to edit by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Edit”, then press
.
3. Press
4. Edit the bookmark title.
For details on entering characters, see “Entering
Characters” on page 24.
.
5. Press
6. Edit the URL address.
.
7. Press
or
to select “Yes”, then press
The selected bookmark has been deleted.
My Text Templates (M 2-5)
You can register up to 20 text templates for use in SMS
and MMS.
You can input messages or others more easily by
registering frequently used text.
128 characters may be registered in any text template.
Adding Phrases to My Text Templates
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
3. Press
Deleting Bookmarks
1. Perform steps 1 to 3 in “Adding a Bookmark” on
page 45.
2. Select the desired bookmark to delete by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Delete”, then press
.
3. Press
4. Press
To cancel deletion, select “No” at step 4, then press
.
.
or
to select “My Text Templates”,
then press
.
The list of My Text Templates is displayed.
4. Select the number you wish to register by pressing
or
, then press
5. Enter the text, then press
.
For details on entering characters, see “Entering
Characters” on page 24.
Editing Text Templates
1. Perform steps 1 to 3 in “Adding Phrases to My Text
Templates”.
My Phone
46
2. Select the number you wish to edit by pressing
or
, then press
or
to select “Delete”, then press
3. Press
.
4. Select “Yes”, then press
.
or
to select “Edit”, then press
3. Press
4. Enter new text.
.
To correct the last character, press
[Clear]
briefly.
Press and hold
[Clear] to clear all characters.
.
5. Press
Viewing Text Templates
1. Perform steps 1 to 3 in “Adding Phrases to My Text
Templates” on page 46.
2. Select the number you wish to view by pressing
or
, then press
.
3. Press
or
to select “Confirm”, then press
.
The selected text template is displayed.
[Back] to return to
4. After confirmation, press
template list.
Deletsing Text Templates
1. Perform steps 1 to 3 in “Adding Phrases to My Text
Templates” on page 46.
2. Select the text template you wish to delete by
pressing
or
, then press
.
47
My Phone
.
The selected text template is deleted.
To cancel deletion, select “No” at step 4, then press
.
Memory Status (M 2-6)
This function helps you to check the memory status of
the Galleries.
to display the Main Menu.
1. Press
or
to select “My Phone”, then press
2. Press
.
3. Press
press
or
.
to select “Memory Status”, then
Fun & Games
Java™ Games
Settings (M 3-1-2)
Operation Priority
You can set the method of incoming phone calls and
alarm whilst a JavaTM application is operated.
1. Press
2. Press
press
3.
4.
5.
6.
to display the Main Menu.
or
to select “Fun & Games”, then
.
Select “JavaTM Games”, then press
Press
or
.
to select “Settings”, then press
Select “Operation Priority”, then press
.
.
Select the option you wish to set by pressing
, then press
.
The options available are:
• “Incoming Call”
• “Alarm”
or
to select methods, then press
7. Press
or
.
• “Priority”:
The JavaTM application is suspended automatically,
and you can receive the call or alarm will sound.
After finishing the call or alarm, the suspend icon
( ) is displayed and you will know there is a
suspended JavaTM application.
• “Notice”:
The marquee (character scrolls) is displayed on the
first line on the screen whilst the JavaTM application
continues. If you press
, the JavaTM application is
suspended, and you can receive the call. After
finishing the call, the suspend icon ( ) is displayed
and you will know there is a suspended JavaTM
application.
Volume
You can set the sound volume of the JavaTM application
such as sound effect to one of the five levels or silent.
When “Ringer Volume” (p. 64) is set to “Silent”, the set
up has a priority.
1. Perform steps 1 to 4 in “Operation Priority”.
or
to select “Sound Volume”,
2. Press
then press
.
The current volume level is displayed.
to increase the volume or press
to
3. Press
decrease the volume and then press
.
Fun & Games
48
Backlight
You can select the method of backlight during the
operation of the JavaTM application from the following
three types:
• “On”:
Lit whilst the JavaTM
application is operated.
• “Off”:
Unlit whilst the JavaTM
application is operated
even if a key is pressed.
• “Normal Settings”:Works with the main backlight
setting. (p. 85)
1. Perform steps 1 to 4 in “Operation Priority” on
page 48.
or
to select “Backlight”, then press
2. Press
.
.
3. Select “On/Off”, then press
4. Select “On”, “Off” or “Normal Settings” by
pressing
or
, then press
.
To Set the Blinking Operation
You can set whether the blinking operation, which is
embedded in JavaTM application, is enabled.
1. Perform steps 1 and 2 in “Backlight”.
or
to select “Blink”, then press
.
2. Press
49
Fun & Games
3. Select “On” or “Off” by pressing
press
or
, then
.
Vibration
When vibrator is set in the JavaTM application, you can
choose whether the operation is enabled or disabled.
When a SMAF file is specified in the JavaTM
application, you can operate the vibrator set in the
SMAF file.
Note
• SMAF (Synthetic music Mobile Application Format)
is a format of music data for mobile phones.
1. Perform steps 1 to 4 in “Operation Priority” on
page 48.
or
to select “Vibration”, then press
2. Press
.
3. Press
or
to select “Enable”, “Disable” or
“Link to Sound”, then press
.
When you set “Link to Sound”, the JavaTM
application is syncronised with the vibrator.
Online Services
You can adjust the display settings of the confirmation
screen when a JavaTM application attempts to connect
to the network.
1. Perform steps 1 to 4 in “Operation Priority” on
page 48.
or
to select “Online Services”, then
2. Press
press
.
3. Press
or
to select “Yes”, then press
.
To cancel confirmation, select “No”, then press
.
5. Press
or
to select “Yes”, then press
.
All settings in a JavaTM application will be reset.
To cancel resetting, select “No”, then press
.
To clear all JavaTM applications
All JavaTM applications stored in Saved Games are
cleared. The preloaded JavaTM application cannot be
deleted.
1. Perform steps 1 to 4 in “Operation Priority” on
page 48.
or
to select “JavaTM Reset”, then press
2. Press
.
JavaTM Reset
3. Enter your handset code, then press
To reset all settings in a JavaTM application
1. Perform steps 1 to 4 in “Operation Priority” on
page 48.
or
to select “JavaTM Reset”, then press
2. Press
.
5. Press
3. Enter your handset code, then press
.
If you enter a wrong handset code, the screen will
return to step 4 in “Operation Priority” on page 48.
.
4. Select “Settings Reset”, then press
.
If you enter a wrong handset code, the screen will
return to step 4 in “Operation Priority” on page 48.
or
to select “All Clear”, then press
4. Press
.
or
to select “Yes”, then press
All JavaTM applications are cleared.
To cancel clearing, select “No”, then press
Fun & Games
.
.
50
JavaTM Information (M 3-1-3)
The information about the license of JavaTM can be
displayed.
Note
• If an incoming call is detected during gameplay, the
game will be stopped.
Download More (M 3-1-4)
See “Download” on page 38 for instructions.
Game Guide
1. Perform steps 1 to 4 in “Starting Games”.
or
to select “Guide”, then press
2. Press
Game instructions are displayed.
Other Games (M 3-2)
Your phone comes complete with 3 games (PK Game,
Collection Hunter, Air Hockey).
You can enjoy these 3 games soon after purchase. You
can also enjoy various games by downloading JavaTM
application games provided in the Internet sites. (p. 38)
Starting Games
to display the Main Menu.
1. Press
or
to select “Fun & Games”, then
2. Press
press
.
3. Press
or
to select “Other Games”, then press
.
The game list is displayed.
or
to select the desired game, then
4. Press
press
.
.
5. Select “New Game”, then press
6. When you have finished playing, press
51
Fun & Games
.
.
Collection Hunter (M 3-2-2)
Check of a collection and reset of a game can be
performed in “Collection Hunter”.
To Check Collection
1. Perform steps 1 to 3 in “Starting Games”.
or
to select “Collection Hunter”,
2. Press
then press
.
3. Press
or
to select “Collection View”,
then press
.
To Reset the Game
1. Perform steps 1 to 3 in “Starting Games”.
or
to select “Collection Hunter”,
2. Press
then press
.
.
3. Select “Reset Game”, then press
or
to select “Yes”, then press
4. Press
.
Air Hockey (M 3-2-3)
The level of the game can be chosen for “Air Hockey”.
To Select a Game Level
1. Perform steps 1 to 3 in “Starting Games” on
page 51.
or
to select “Air Hockey”, then press
2. Press
.
3. Press
4. Press
or
to select “Level”, then press
.
or
to select the level, then press
.
Setting up Game Options (M 3-2-4)
1. Perform steps 1 to 3 in “Starting Games” on
page 51.
or
to select “Game Settings”, then
2. Press
press
.
3. Press
or
to select “Backlight” or “Enable
Vibrate” to change the settings, then press
.
4. Press
or
to select “On” or “Off”, then press
.
5. Press
or
to select “Sound Volume” to adjust
the sound volume, then press
.
6. Press
to increase the sound volume or press
to decrease the sound volume and then press
.
Note
• If you wish to mute the sound during gameplay, press
. Press
again to return the volume.
Melody Editor (M 3-3)
You can create an original ringing tone by yourself, or
you can send a melody attached to an MMS.
You can input up to 190 tones × 16 chords, or 380 tones
× 8 chords per melody.
The original ringing tone is registered in the Saved
Sounds.
Creating Your Original Ringing Tone (M 3-3-1)
to display the Main Menu.
1. Press
or
to select “Fun & Games”,
2. Press
then press
.
3. Press
or
to select “Melody Editor”,
then press
.
4. Select “Create New”, then press
5. Enter the title.
.
Up to 24 characters can be entered.
For details on entering characters, see “Entering
Characters” on page 24.
.
6. Press
Fun & Games
52
7. Press
or
to select a tempo, then press
.
The music tempo is described below.
• “Allegro (Fast)”:
150
• “Moderato (Normal)”:
125
• “Andante (Slow)”:
107
• “Adagio (Very Slow)”:
94
Tempo is defined by the number of crotchets ( )
played per minute.
8. Select “8 Chords” or “16 Chords” by pressing
or
, then press
.
9. Specify the musical scale and rest using the digit
keys.
For details on specifying the sound level and rest,
see “Specify the Musical Scale and Rest” on
page 54.
10. Specify the types of musical notes or rest using
or
keys.
For details on specifying the musical notes and rest,
“Specifying the Types of Notes and Rests” on
page 54.
key after inputting one note.
11. Press
Input the next note after the cursor moves to the
right.
53
Fun & Games
12. Repeat steps 9 to 11 to input notes.
When you press
during input, the melody that
you have entered is played back.
When you press
[Options] and select “Play
before Cursor” whilst entering notes, the melody,
that is displayed on the screen, is played back up to
the cursor position.
When you press
[Options] and select “Select
Chord”, you can select another chord. Repeat steps
9 to 11 to input notes for the new chord.
[Options] to
13. When you finish inputting, press
display the Options Menu.
.
14. Select “Save”, then press
or
to select “Save to My Phone”, then
15. Press
press
.
Your original ringing tone is registered in the Saved
Sounds.
Note
• If the capacity or memory in the Saved Sounds
becomes insufficient, the message of “Maximum
Capacity : 80 Not registered” or “Not registered.
Memory Full” is displayed respectively. At that time,
the display returns to the screen of step 15. Try again
after deleting unnecessary data (p. 45).
Specify the Musical Scale and Rest
Using the key shown below, specify the musical scale
and rest.
Do
Re
Mi
Fa
Sol
La
Ti
Specifying the Types of Notes and Rests
Specify notes and rests by pressing
or
repeatedly.
Rest
When you press the key shown above once, a crotchet
is specified in the middle scale (no mark).
When you press the same key repeatedly, the note will
shift cycle through the available octave ranges.
When you press
or
whilst a note is selected, the
note will raise one semitone higher or lower.
When entering rest: Crotchet rest is entered.
(
)
Crotchet (Crotchet rest)
(
)
Quaver (Quaver rest)
(
)
Semiquaver (Semiquaver rest)
(
)
Semibreve (Semibreve rest)
(
)
Minim (Minim rest)
When you make a dotted note or triplet, press
after selecting the target note.
Fun & Games
54
Note
• You cannot make a dotted semiquaver (semiquaver
rest) or a dotted semibreve (semibreve rest).
• Three continuous notes are required for triplet.
To specify a tie, press
after selecting the target
notes.
An underscore (_) is displayed next to the note, and the
note is tied with the next one.
To enter the next note, press
and move the cursor to
the right. Then, repeat the operation on the previous
page.
If the cursor is positioned next to a note, you can repeat
the note immediately left of the cursor when
or
is pressed.
Set the Tone
The phone can play notes using different instruments.
1. Perform steps 1 to 13 in “Creating Your Original
Ringing Tone” on page 52.
or
to select “Tone Set”, then press
2. Press
.
or
3. Select a category of the tone by pressing
or
, then press
4. Select a tone by pressing
.
When “Play Current Chord” is selected, the melody
entered is played back in the selected tone.
When “Confirm Tones” is selected, the syllable
names are played back in the selected tone.
.
5. Select “OK”, then press
Now you can create a melody.
You can select from the following 128 tones.
Category
Pianos
55
Fun & Games
.
Tone
Category
Piano
Bright Piano
E. Grand Piano
Honky-Tonk
Chimes
Electric Piano 1
Electric Piano 2
Harpsichord
Clavi
Tone
Celesta
Glockenspiel
Music Box
Vibraphone
Marimba
Xylophone
Tubular Bells
Dulcimer
Category
Organs
Basses
Strings 2
Tone
Category
Drawbar Organ
Perc. Organ
Rock Organ
Church Organ
Guitars
Reed Organ
Accordion
Harmonica
Tango Accordion
Acoustic Bass
Finger Bass
Pick Bass
Fretless Bass
Strings 1
Slap Bass 1
Slap Bass 2
Synth Bass 1
Synth Bass 2
Str. Ensemble 1
Str. Ensemble 2
Synth Strings 1
Synth Strings 2
Brasses
Choir Aahs
Voice Oohs
Synth Voice
Orchestra Hit
Tone
Nylon Guitar
Steel Guitar
Jazz Guitar
Clean Guitar
Muted Guitar
Overdriven Gtr.
Distortion Gtr.
Gtr. Harmonics
Violin
Viola
Cello
Contrabass
Tremolo Strings
Pizz. Strings
Harp
Timpani
Trumpet
Trombone
Tuba
Muted Trumpet
French Horn
Brass Section
Synth Brass 1
Synth Brass 2
Category
Reeds
Synth
Leads
Synth
Effects
Tone
Soprano Sax
Alto Sax
Tenor Sax
Baritone Sax
Oboe
English Horn
Bassoon
Clarinet
Square Lead
Sawtooth Lead
Calliope Lead
Chiff Lead
Charang Lead
Voice Lead
Fifth Lead
Bass & Lead
Rain
Soundtrack
Crystal
Atmosphere
Brightness
Goblins
Echoes
Science Fiction
Category
Flutes/
Pipes
Synth
Pads
Ethnics
Tone
Piccolo
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
New Age Pad
Warm Pad
Polysynth Pad
Choir Pad
Bowed Pad
Metallic Pad
Halo Pad
Sweep Pad
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
Fun & Games
56
Category
Percussions
Original
Tone
Category
Tinkle Bell
Agogo
Steel Drums
Woodblock
Effects
Taiko Drums
Melodic Tom
Synth Drum
Reverse Cymbal
Original 1 (Piano)*
Original 2 (Glockenspiel)*
Original 3 (Reed Organ)*
Original 4 (Nylon Guitar)*
Original 5 (Violin)*
Tone
Gtr. Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone Ring
Helicopter
Applause
Gunshot
* The default setting tone.
To create your original tone, see “Creating Your Original
Tone” on page 61.
Setting the Strength of the Original Ringing Tone
The strength of the original ringing tone can be set in 3
levels for each melody.
When you purchase this phone, the strength of the
original ringing tone is set to “forte (Loud)”.
1. Perform steps 1 to 13 in “Creating Your Original
Ringing Tone” on page 52.
or
to select “Strength Set”, then press
2. Press
.
3. Select a strength of the tone by pressing
or
,
then press
.
When “Play Current Chord” is selected, the original
ringing tone entered is played back in the selected
strength of the tone.
.
4. Select “OK”, then press
Now you can create an original ringing tone.
Deleting an Original Ringing Tone
Perform steps 1 to 4 in “Deleting Sounds” on page 45.
Editing Original Ringing Tones
1. Perform steps 1 to 3 in “Creating Your Original
Ringing Tone” on page 52.
or
to select “Existing Melodies”, then
2. Press
press
.
57
Fun & Games
3. Press
or
to select an original ringing tone
you wish to edit, then press
[Options].
The Options Menu is displayed.
or
to select “Data Edit”, then press
4. Press
.
.
5. Edit the title and press
or
to select a tempo, then press
.
6. Press
or
to select the number of chords, then
7. Press
press
.
8. Select a note you wish to change by pressing
or
, then edit notes.
For details on editing tones, see “Tone Editor” on
page 59.
When you add notes, enter the note correctly on the
cursor.
To delete a note, press
[Clear] briefly.
Press and hold
[Clear] to clear all tones.
[Options] to
9. When you finish editing, press
display the Options Menu.
.
10. Select “Save”, then press
11. Select “Save to My Phone”, then press
12. Press
or
to select “Over Write”, then press
.
The original ringing tone is changed.
If you select “New”, the melody before the
correction is not modified. The original ringing tone
is registered as a new original ringing tone.
Note
• When the number of chords is modified in step 7, the
confirmation screen may be displayed. When you
select “Yes”, a section of the melody may be deleted.
• When you are going to add notes in step 8, you cannot
add any notes if you have already entered 380 notes
(for 8 chords melodies) or 190 notes (for 16 chords
melodies).
Tip
• To delete the continuous melody, press
[Options]
and then press
after selecting “DEL after
Cursor” or “DEL before Cursor.” You can delete the
melody after the cursor or before the Cursor.
.
Fun & Games
58
Copying and Pasting Notes
You can copy and move a part of a melody to another
position.
Only original ringing tones or editable melodies can be
copied or moved.
1. Perform steps 1 to 7 in “Editing Original Ringing
Tones” on page 57.
[Options] to display the Options Menu.
2. Press
3. Press
press
or
.
to select “Copy” or “Cut”, then
4. Move the cursor to the first note to be copied or to
be cut and press
.
5. Move the cursor to the last note to highlight the area
and press
.
The highlighted area will be saved temporarily in
the memory. If you select “Cut” in step 3, the
highlighted area will be cut.
[Options] to display the Options Menu.
6. Press
or
to select “Paste”, then press
.
7. Press
8. Move the cursor to the point you wish to paste the
notes, then press
.
Saved notes are pasted.
59
Fun & Games
Tone Editor (M 3-4)
You can make a tone and use it for the original ringing
tone.
Up to five types of tones can be registered respectively
for 8 chords and 16 chords.
FM Sound Source
Various types of tones can be composed by combining
the functions that generate one sine wave called an
“Operator”. The combination of the operator is called
an algorithm.
The operator acts as the modulator (modulating part) or
the carrier (modulated part) depending on the
algorithm.
• In each operator, various parameters such as multiple
or envelope can be set.
• By setting the feedback to the specified operator,
wider tone ranges can be created.
Setting an Algorithm
Set the combination of the operator.
Select from 4 types of combinations in 8 chords, and 2
types in 16 chords.
8 Chords
Algorithm3
Algorithm4
Algorithm5
Parameter
Multiple
(13 levels)
Algorithm6
16 Chords
Algorithm1
Setting the Operator
The meaning and content of the parameter that can be
set to the operator is described below.
Algorithm2
(Green number): The modulator (modulating part)
(White number): The carrier (modulated part)
Meaning
When the value of the carrier is large, the
sound becomes high. You can set various
types of notes by changing the values of the
modulator.
Envelope
(Continuous/Decay)
This sets continuous same note or fade-out.
Sustain
(On/Off)
This sets a note to be sustained after completing the note. If you want to have a note
with reverberation, set this function on.
Key Scale
Rate
(2 levels)
Key Scale
Level
(4 levels)
Total Level
(64 levels)
Attack Rate
(15 levels)
Set the function to “2” if you want to a short
note.
This function sets the rate of reducing the
volume as a note becomes higher.
In the carrier, the volume becomes large as
this level becomes higher.
In the modulator, the melody becomes
brighter as this level becomes higher. The
melody becomes softer as this level
becomes smaller.
This sets the time from the beginning of the
sound to the maximum volume.
Fun & Games
60
Parameter
Decay Rate
(16 levels)
Sustain
Level
(16 levels)
Release
Rate
(16 levels)
Wave
Shape
(8 types)
Vibrato
(4 levels/
Off)
Tremolo
(4 levels/
Off)
Feedback
(8 levels)
Meaning
This sets the time from the maximum volume
to the volume of the sustain level.
In sustaining note, this displays the volume
of the sound that continues to produce. In
fading-out note, this displays the volume
when the note starts fading-out.
In sustaining note, this displays the sustaining time from note completion to no sound.
In fading-out note, this displays the time from
starting fade-out to no sound.
Select the basic wave type from eight types.
Type 1
Type 5
Type 2
Type 6
Type 3
Type 7
Set the Effect Frequency
Define the frequency of the vibrato or tremolo.
The frequency becomes faster as the figure increases.
Creating Your Original Tone
to display the Main Menu.
1. Press
or
to select “Fun & Games”, then
2. Press
press
.
3. Press
or
to select “Tone Editor”, then press
.
Type 4
4. Select “For 8 Chords” or “For 16 Chords” by
Type 8
5. Select the number you wish to register and press
Set the vibrato. If the vibrato is used, select
from 4 levels.
Set the tremolo. If the tremolo is used, select
from 4 levels.
Set the level of modulation in the modulator
feedback for Operator 1.
pressing
or
, then press
.
.
or
to select “Rename”, then press
6. Press
7. Enter the title.
Up to 16 characters can be entered.
For details on entering characters, see “Entering
Characters” on page 24.
.
8. Press
9. Press
press
or
.
to select “Base Tone Set”, then
10. Select a category of the tone by pressing
61
Fun & Games
.
or
.
11. Select a base tone by pressing
or
, then press
.
When “Confirm Tones” is selected, the syllable
names are played back in the selected tone.
.
12. Select “OK”, then press
13. Press
or
.
to select “Details Editor”, then
press
14. Press
or
to select “Algorithm x”, then press
.
15. Select an algorithm you wish to set by pressing
or
, then press
.
If you do not wish to change the operator, skip to
step 20.
16. Select an operator you wish to change by pressing
or
, then press
.
The basic note parameter is set in advance.
17. Select a parameter you wish to change by pressing
or
.
18. Press
or
to change the content of the
parameter.
For details of parameter, see pages 60 to 61.
When you press
, the syllable names are played
back in the selected content of the parameter.
Repeat steps 17 and 18 to change another content of
the parameter.
or
to select “Setup End”, then press
19. Press
.
If you do not wish to change the effect frequency,
skip to step 22.
or
to select “Effect Frequency”, then
20. Press
press
.
21. Select the effect frequency you wish to set by
pressing
22. Press
or
or
, then press
.
to select “Details End”, then press
.
23. Press
or
to select “Save”, then press
Your original tone is registered.
Fun & Games
.
62
Profiles (M 4)
Note
• When a profile is set, the icon which corresponds to
the profile name appears in the stand-by screen:
Normal:
Is the default setup. (not displayed
in the stand-by screen)
Meeting:
For use when discretion is needed.
Activity:
For use in busy environments.
Car:
For use in the car. (connected to a
hands free kit)
Silent:
For use when silence is needed.
All sounds are muted and you are
alerted to calls with the vibrator.
You can easily alter the phone tone (e.g. the ringer
volume, keypad tones, etc.) according to your
environment.
Tone sound and vibration set can be customized for
each profile.
There are 5 profiles including one user definable
profile:
• Normal
• Meeting
• Activity
• Car
• Silent
Tip
• You can also activate a profile by pressing and
holding
for approximately 2 seconds instead of
steps 1and 2.
Activating a Profile
to display the Main Menu.
1. Press
or
to select “Profiles”, then press
.
2. Press
3. Select the profile you wish to activate by pressing
or
4. Press
, then press
.
or
to select “Activate”, then press
The profile will now be activated.
Customising Profiles
1. Perform steps 1 and 2 in “Activating a Profile”.
2. Select the profile you wish to customise by pressing
or
.
or
63
Profiles
, then press
.
or
to select “Edit”, then press
.
3. Press
4. Select the setting you wish to customise by pressing
, then press
.
Ringer Volume
5. Change the setting you want.
Resetting Profile Settings
You can adjust the ringer volume to one of 5 levels.
When it is set to “Silent”, the volume of games and
JavaTM applications is muted.
1. Perform steps 1 and 2 in “Activating a Profile” on
1. Perform steps 1 to 3 in “Customising Profiles” on
For details about settings, see pages 64 to 68.
page 63.
2. Select the profile you wish to reset by pressing
or
, then press
.
3. Press
4. Press
press
or
to select “Edit”, then press
or
.
to select “Set to Default”, then
.
5. Enter your handset code, then press
or
to select “Yes”, then press
6. Press
To cancel the resetting, select “No”, then press
Note
• If you enter a wrong handset code in step 5, the
screen returns to step 4.
page 63.
2. Press
or
to select “Ringer Volume”, then
press
.
The current volume level is displayed.
to increase the ringer volume or press
3. Press
to decrease the ringer volume and then press
.
To select “Step Tone”, press
at level 5.
To select “Silent”, press
at level 1.
.
.
.
Ringer Type
You can select the ringing tone from 30 tones including
5 patterns, 15 sound effects and 10 melodies. You can
also select a sound in the Saved Sounds as the default
ringing tone excluding the WAVE format.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Assign Melody”, then
2. Press
press
.
Profiles
64
3. Press
or
to select “Preset Melody” or “My
Sounds”, followed by
.
4. Select the ringing tone you wish to use by pressing
or
.
If you wish to hear the demo, press
To stop playing, press
[Stop].
5. When selection is complete, press
[Play].
.
Vibration
When the vibrator option is set to on, the phone will
vibrate for incoming calls regardless of the ringer
volume and tone settings.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Vibration”, then press
2. Press
.
3. Press
or
to select “Enable”, “Disable” or
“Link to Sound”, then press
.
Tip
• When “Link to Sound” is selected in step 3, melodies
are synchronised with the vibrator for the ringing
tone. However, this function may not work depending
on data.
• When you select “Enable” or “Link to Sound” in step
3, “ ” appears on the stand-by screen.
Keypad Tones
When the keypad tone is set to on, you will hear a
confirmation tone each time you press a numerical key.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Keypad Tones”, then
2. Press
press
.
3. Press
or
to select “On” or “Off”, then press
.
If you select “Off”, the screen returns to step 1.
.
4. Set “Volume”, then press
5. Press
to increase the volume or press
decrease the volume, then press
.
6. Press
7. Press
or
to
to select “Melody”, then press
or
to select either “Preset Melody”,
“My Sounds” or “Default Tone”, then press
.
65
Profiles
.
When you select “Preset Melody” or “My Sounds” in
step 7:
8. Select the keypad tone.
For details on selecting a ringing tone, see “Ringer
Type” on page 64.
or
to select “Duration”, then press
9. Press
.
10. Set the duration by pressing
or
, then press
.
to select “Melody”, then press
3. Press
or
to select “On” or “Off”, then press
.
If you select “Off”, the screen returns to step 1.
.
4. Select “Volume”, then press
.
or
to select “Preset Melody” or “My
Sounds”, then press
.
8. Select the warning tone.
For details on selecting a ringing tone, see “Ringer
Type” on page 64.
or
to select “Duration”, then press
9. Press
.
press
This function enables your phone to emit the warning
tone when an error occurs.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Warning Tone”, then
2. Press
press
.
to increase the volume or press
decrease the volume, then press
.
or
10. Select the duration by pressing
Warning Tone
5. Press
6. Press
7. Press
or
, then
.
Power On/Off Sound
You can set up to emit a sound and select the melody,
volume and duration when the phone is turned on or off.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Power On Sound” or
2. Press
“Power Off Sound”, then press
.
to
Profiles
66
3. Press
or
to select “On” or “Off”, then press
.
If you select “Off”, the screen returns to step 1.
.
4. Select “Volume”, then press
5. Press
to increase the volume or press
decrease the volume and then press
.
6. Press
7. Press
or
to
to select “Melody”, then press
.
or
to select “Preset Melody” or “My
Sounds”, then press
.
8. Select the ringing tone.
Message Alert
When receiving messages, special ring tones can be set.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Message Alert”, then
2. Press
press
.
3. Press
or
to select “MMS”, “SMS” or
“WAP”, then press
.
.
4. Select “Volume”, then press
to increase the volume or press
5. Press
decrease the volume and then press
For details on selecting a ringing tone, see “Ringer
Type” on page 64.
or
to select “Duration”, then press
9. Press
.
6. Press
7. Press
10. Enter the duration of ringing tone in 2 digits (01 to
8. Select the ringing tone.
10 seconds) using the digit keys, then press
.
or
to
.
to select “Melody”, then press
or
to select “Preset Melody” or “My
Sounds”, then press
.
For details on selecting a ringing tone, see “Ringer
Type” on page 64.
or
to select “Vibration”, then press
9. Press
.
10. Press
or
to select “Enable”, “Disable” or
“Link to Sound”, then press
.
67
Profiles
.
11. Press
or
to select “Duration”, then press
.
12. Enter the duration of ring tone in 2 digits (01 to 99
seconds) using the digit keys, then press
.
Low Battery Alert
Adjust the volume of the alarm when the battery
becomes low.
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63.
or
to select “Low Battery Alert”, then
2. Press
press
.
3. Press
to increase the volume or press
decrease the volume and then press
.
to
Any Key Answer
1. Perform steps 1 to 3 in “Customising Profiles” on
page 63
.
2. Select “Any Key Answer”, then press
or
, then
3. Select “On” or “Off” by pressing
press
.
Profiles
68
Organiser
6. If you wish to start a new calculation, press
When calculation is complete, press
Calculator (M 5-1-1)
The calculator function performs the 4 arithmetic
calculations using up to 12 digits.
to display the Main Menu.
1. Press
or
to select “Organiser”, then press
2. Press
.
3. Select “Calculator”, then press
4. Select “Calculator”, then press
.
.
The calculator appears on the display.
5. Key operations for calculation are as follows.
Rate Conversion
You can also use the calculator as a currency calculator
to convert from/to a home currency using a conversion
rate that you enter.
To Set a Currency Conversion Rate (M 5-1-2)
1. Perform steps 1 to 3 in “Calculator”.
or
to select “Exchange Rate”, then
2. Press
press
.
3. Press
or
to select “Foreign Domestic” or
“Domestic Foreign”, then press
.
To delete all digits, press
[Clear].
.
4. Enter the currency conversion rate, then press
To Convert a Value
1. Perform steps 1 to 4 in “Calculator”.
2. Enter the value to be converted, then press
To enter a decimal point, press
.
To clear the entered number or operand, press
[C].
To do the calculations, press
.
69
Organiser
[C].
.
.
3. Press
or
to select “In Domestic” or “In
Foreign”, then press
.
The result is displayed.
If you select “Exchange Rate” in step 3, you can set
a currency conversion rate.
.
4. When calculation is complete, press
Note
• You cannot perform step 2 when a sign of the four
fundamental processes of arithmetic is displayed.
Calendar (M 5-2)
The Calendar function helps you organise and manage
your busy schedule. You can view the stored schedule
on a monthly basis.
1. Press
2. Press
to display the Main Menu.
or
to select “Organiser”, then press
.
3. Press
or
to select “Calendar”, then press
.
The current month will be displayed and current
date will be highlighted.
4. Select the day for the schedule by pressing , ,
or
, then press
.
5. Press
press
or
.
and select the note number, then
6. Enter the schedule content, press
.
Up to 3 schedule items can be stored.
For details on entering characters, see “Entering
Characters” on page 24.
If you wish to add another item, repeat steps 5 and 6.
[Back].
7. When you have finished entering, press
The screen returns to the calendar. Dates with
scheduled tasks/meetings are underlined.
Note
• The calendar can be displayed for dates from
January 2000 through to December 2099.
Find a Particular Date
You can move the view to a specified date in the
calendar.
[Options] to display the Option Menu.
1. Press
.
2. Select “Go to Date”, then press
3. Enter the date of the calendar to be displayed, then
press
.
The specified date is displayed.
Organiser
70
Deleting Schedules
5. Select “Yes”, then press
To Delete Schedule Items
1. Perform steps 1 to 3 in “Calendar” on page 70.
,
or
, then
2. Select the day by pressing ,
press
.
or
3. Select the item you wish to delete by pressing
, then press
[Options].
The Options Menu is displayed.
or
to select “Delete”, then press
.
4. Press
.
5. Select “1 Data”, then press
1. Perform steps 1 to 3 in “Calendar” on page 70.
[Options] to display the Options Menu.
2. Press
or
to select “Delete” to delete all
3. Press
6. Select “Yes”, then press
5. Select “Yes”, then press
To Delete All Scheduled Tasks/Meetings for a
Specific Day
1. Perform steps 1 to 3 in “Calendar” on page 70.
,
2. Select the day you wish to delete by pressing
,
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Delete”, then press
.
3. Press
4. Select “1 Day” to delete all contents for a day, then
press
.
Clock & Alarm
.
To cancel deleting, select “No” at step 6, then press
.
.
To cancel deleting, select “No” at step 5, then press
.
To Delete All Scheduled Entries
scheduled entries, then press
or
to select “All Data” to delete all
scheduled entries, then press
.
.
To cancel deleting, select “No” at step 3, then press
.
You need to set the correct time and date in order for
your phone’s various time-based functions to work
correctly.
Setting the Date and Time (M 5-3-4)
to display the Main Menu.
1. Press
or
to select “Organiser”, then press
2. Press
.
3. Press
press
71
Organiser
.
4. Press
or
.
to select “Clock & Alarm”, then
4. Press
press
or
.
to select “Set Date/Time”, then
or
to select “Date Format”, then press
.
5. Enter the day, month, year and time using the digit
keys, then press
.
When you enter the time in a 12-hour clock format,
press
and change am/pm.
The order in which the date and time appears is
based on the format setting. See “To Select the Date
Format”.
To Select the Time System
1. Perform steps 1 to 3 in “Setting the Date and Time”
on page 71.
or
to select “Clock Settings”, then
2. Press
press
.
.
3. Select “Time Format”, then press
or
to select “12 hour” or “24 hour”,
4. Press
then press
3. Press
.
To Select the Date Format
The date format can be switched between “Day-MonthYear”, “Month-Day-Year” or “Year-Month-Day”.
1. Perform steps 1 to 3 in “Setting the Date and Time”
on page 71.
or
to select “Clock Settings”, then
2. Press
press
.
4. Press
or
to select “D-M-Y”, “M-D-Y” or
“Y-M-D”, then press
.
To Set the Clock Display
1. Perform steps 1 to 3 in “Setting the Date and Time”
on page 71
or
to select “Clock Settings”, then
2. Press
press
.
3. Press
press
or
.
to select “Display Format”, then
4. Press
or
to select “Time Only”, “Date Only”
or “Date & Time”, then press
.
To set hide clock, select “Off” at step 4, then press
.
When “Wallpaper” is set to “On”, the date is not
displayed in the main screen.
To Set Daylight Saving Time
You can switch to daylight saving time without having
to change the clock time itself.
1. Perform steps 1 to 3 in “Setting the Date and Time”
on page 71
Organiser
72
2. Press
or
.
to select “Clock Settings”, then
or
.
to select “Daylight Saving”, then
press
4. Press
or
to select “On”, then press
press
3. Press
.
Setting the Time Zone (M 5-3-3)
1. Perform steps 1 to 3 in “Setting the Date and Time”
on page 71.
or
to select “Set Time Zone”,
2. Press
then press
.
.
3. Select “Change Zone”, then press
or
to set the home city, then press
4. Press
.
To Customise the Time Zone
1. Perform steps 1 to 3 in “Setting the Date and Time”
on page 71.
or
to select “Set Time Zone”, then
2. Press
press
.
3. Press
press
or
.
to select “Set Custom Zone”, then
4. Enter the time using the digit keys, then press
Each press of
73
Organiser
switches - and +.
.
Setting Alarm (M 5-3-1)
Alarm function allows you to be alerted at a specified
time.
Note that the alarm may not function correctly if the
clock has not been set.
to display the Main Menu.
1. Press
or
to select “Organiser”, then press
2. Press
.
3. Press
press
or
.
to select “Clock & Alarm”, then
.
4. Select “Set Alarm”, then press
.
5. Select “List Alarm”, then press
or
to select the desired alarm number,
6. Press
then press
.
Up to 5 alarm times can be specified.
.
7. Select “Set Time”, then press
8. Enter the alarm time using the digit keys, then press
.
When you enter the alarm time in a 12-hour clock
format, press
and change am/pm.
or
to select “Repeat Daily”, then press
9. Press
.
10. Press
or
to select “On” or “Off”, then press
or
to select “Alarm Status”, then press
or
to select “On”, then press
.
11. Press
.
12. Press
13. Press
.
3. Press
or
to select “Vibration”, then press
.
[Save].
To Change the Type of Alarm Tone
1. Perform steps 1 to 6 in “Setting Alarm” on page 73.
or
to select “Alarm Tone”, then press
2. Press
.
.
3. Select “Melody”, then press
or
to select “Preset Melody” or “My
4. Press
Sounds”, then press
To Change the Vibration of Alarm
1. Perform steps 1 to 6 in “Setting Alarm” on page 73.
or
to select “Alarm Tone”, then press
2. Press
.
.
or
to select “Enable”, “Disable” or
“Link to Sound”, then press
.
To Change the Duration of Alarm
1. Perform steps 1 to 10 in “Setting Alarm” on
page 73.
or
to select “Alarm Tone”, then press
2. Press
.
3. Press
5. Select the alarm tone.
If you wish to hear the demo play, press
To stop playing, press
[Stop].
.
6. When selection is complete, press
4. Press
[Play].
or
to select “Duration”, then press
.
The current duration is displayed.
4. Enter the length of the duration in 2 digits (02 to 59
seconds) using the digit keys, then press
.
Organiser
74
Changing Alarm Settings
1. Perform steps 1 to 5 in “Setting Alarm” on page 73.
2. Select the number you wish to change by pressing
or
, then press
.
Resetting All Alarm Settings
1. Perform steps 1 to 4 in “Setting Alarm” on page 73.
or
to select “Clear All”, then press
2. Press
.
3. Change Alarm settings.
3. Press
For details on changing Alarm settings, see “To
Change the Type of Alarm Tone” on page 74.
Disabling Alarm Function
1. Perform steps 1 and 2 in “Changing Alarm
Settings”.
or
to select “Alarm Status”, then press
2. Press
.
3. Press
4. Press
or
to select “Off”, then press
.
[Save].
” disappears from the screen.
“
3. Press
or
to select “Reset Alarm”, then press
or
to select “Yes”, then press
.
4. Press
75
Organiser
.
to select “Yes”, then press
.
Voice Memo (M 5-4)
This allows you to record a voice message of up to 10
seconds, which can be used to remind you of schedule
entries or be sent within an MMS. The recorded voice
memo is registered in the My Sounds.
Recording a Voice Memo
to display the Main Menu.
1. Press
or
to select “Organiser”, then press
2. Press
3. Press
Resetting an Alarm Setting
1. Perform steps 1 to 5 in “Setting Alarm” on page 73.
2. Select the number you wish to reset by pressing
or
, then press
.
or
or
.
to select “Voice Memo”, then press
.
4. Press
to start recording.
To stop recording before the recording time is over,
press
[Stop].
5. Select “Save” to save the voice memo, then press
.
If you wish to exit the voice memo, press
then select “Yes”.
[Exit],
Tip
• You can also record a voice memo by pressing
and
instead of steps 1 to 3.
• If you wish to record a voice memo again, select
“Record Again” in step 5. The screen will return to
step 4.
To Play Back the Saved Voice Memo
1. Perform steps 1 to 4 in “Recording a Voice Memo”
on page 75.
or
to select “Playback”, then press
.
2. Press
Help List (M 5-5)
You can view the help list and use it to guide you in the
phone’s functions.
to display the Main Menu.
1. Press
or
to select “Organiser”, then press
.
2. Press
3. Press
or
to select “Help List”, then press
.
The help list is displayed.
and
.
4. Check the key operation by pressing
5. When you have finished, press
[Back].
3. Press
.
The recorded voice memo is played back.
To stop playback, press
[Stop].
Organiser
76
Call Manager
Call Log
The phone will record the last 10 missed calls, received
calls and dialled numbers.
Viewing Call Log
to display the Main Menu.
1. Press
or
to select “Call Manager”, then press
2. Press
.
3. Press
or
to select “Call Register”, then press
.
4. Press
or
to select “Missed Calls”, “Received
Calls” or “Dialled Numbers”, then press
.
The selected call log list is displayed.
5. Select the number you wish to view by pressing
or
.
6. Press
[View].
Call record “1” is the most recent.
When you press
, call record “2” will be
displayed.
If you wish to dial the number, press
.
[Back] to return
7. When you have finished, press
to step 4.
77
Call Manager
Tip
• You can also confirm call records by pressing
in
stand-by mode.
• You can switch between histories by pressing
or
in step 5 only when you enter by
in stand-by
mode.
Sending Messages
1. Perform steps 1 to 5 in “Viewing Call Log”.
2. Select the file name you wish to send by pressing
or
, then press
.
3. Press
press
4. Press
press
or
.
to select “Send Message”, then
or
.
to select “MMS” or “SMS”, then
5. Enter your message.
For details on creating a message, see “Creating a
New MMS” on page 106 or “Creating a New SMS”
on page 114.
Deleting Call Log
Deleting Single Call Record
1. Perform steps 1 to 5 in “Viewing Call Log”.
.
2. Press
3. Press
or
to select “Delete”, then press
.
4. Press
or
to select “Yes”, then press
.
The selected call record will be deleted.
To cancel deletion, select “No” in step 4, then press
.
To Delete All Call Log (M 6-2-4)
1. Perform steps 1 to 3 in “Viewing Call Log” on
page 77.
2. Press
or
to select “Clear Logs”, then press
.
.
3. Select “All Calls”, then press
or
to select “Yes”, then press
4. Press
.
All call log records will be deleted.
To cancel deleting, select “No” in step 4, then press
.
Tip
• If you select “Missed Calls”, “Received Calls” or
“Dialled Numbers” in step 3, the call log in the
selected category will be deleted.
Call Timers (M 6-2-5)
This function lets you check the duration of your calls.
Checking the Duration of the Last Call
to display the Main Menu.
1. Press
or
to select “Call Manager”, then press
2. Press
.
3. Press
or
to select “Call Register”, then press
or
to select “Call Timers”, then press
.
4. Press
.
5. Select “Last Call”, then press
.
The duration of the last call is now displayed.
[Back] to return
6. When you have finished, press
to call timers menu.
Checking the Total Call Time
or
to select “All Calls”, then press
1. Press
in step 5 in “Checking the Duration of the Last
Call”.
[Back].
2. When you have finished, press
Resetting All Call Timers
1. Perform steps 1 to 4 in “Checking the Duration of
the Last Call”.
Call Manager
78
2. Press
or
to select “Clear Timers”, then press
.
or
to select “Yes”, then press
.
3. Press
.
To cancel resetting, select “No”, then press
.
4. Enter your handset code, then press
The Call Timers are reset to zero.
Call Costs (M 6-2-6)
This function lets you check the charges for your calls.
Charging Advice is not supported on all networks.
Please check with your service provider for availability.
Checking the Cost of the Last Call
to display the Main Menu.
1. Press
or
to select “Call Manager”, then press
2. Press
.
3. Press
or
to select “Call Register”, then press
or
to select “Call Costs”, then press
.
4. Press
.
5. Select “Last Call”, then press
.
The cost of the last call is now displayed.
[Back] to return
6. When you have finished, press
to call costs menu.
Checking the Total Call Cost
or
to select “All Calls”, then press
1. Press
in step 5 in “Checking the Cost of the Last Call”.
[Back].
2. When you have finished, press
79
Call Manager
Setting the Charge Rate
Set the charge rate to calculate the call cost and set the
maximum limit for call cost.
1. Perform steps 1 to 4 in “Checking the Cost of the
Last Call” on page 79.
or
to select “Cost Units”, then press
.
2. Press
3. Press
or
to select “Set Units”, then press
.
.
4. Enter your PIN2 code, then press
.
5. Enter a cost per unit, then press
To enter a decimal point, press
.
6. Enter a currency unit (up to 3 characters), then press
.
Checking the Charge Rate
1. Select “Read Units”, then press
at step 3 in
“Setting the Charge Rate”.
The charge rate is now displayed.
[Back].
2. When you have finished, press
Setting the Charge Limit
This function is useful if you wish to make sure you do
not exceed a certain charge limit.
1. Perform steps 1 to 4 in “Checking the Cost of the
Last Call” on page 79.
or
to select “Max Cost”, then press
.
2. Press
3. Press
or
to select “Set Limit”, then press
.
4. Enter your PIN2 code, then press
.
5. Enter a value, then press
To enter a decimal point, press
.
.
Checking the Charge Limit
at step 3 in
1. Select “Read Limit”, then press
“Setting the Charge Limit”.
The value of the charge limit is now displayed.
[Back].
2. When you have finished, press
Call Manager
80
Resetting All Call Costs
Data Counter (M 6-2-7)
1. Perform steps 1 to 4 in “Checking the Cost of the
You can confirm the amount of bytes which you used
in the GPRS transmission.
to display the Main Menu.
1. Press
or
to select “Call Manager”, then press
2. Press
.
Last Call” on page 79.
or
to select “Clear Costs”, then press
2. Press
.
3. Press
or
to select “Yes”, then press
To cancel resetting, select “No”, then press
.
4. Enter your PIN2 code, then press
The Call Costs are reset to zero.
.
.
Checking the Residual Credit
1. Perform steps 1 to 4 in “Checking the Cost of the
Last Call” on page 79.
or
to select “Residual Credit”, then
2. Press
press
.
3. When you have finished, press
[Back].
3. Press
or
to select “Call Register”, then press
or
to select “Data Counter”, then press
.
4. Press
.
5. Press
or
to select “Last Data” or “All Data”,
then press
.
You can now check the amount of bytes.
[Back].
6. When you have finished, press
Resetting All Data Counter
1. Perform steps 1 to 4 in “Data Counter”.
or
to select “Clear Counter”, then press
2. Press
.
3. Press
or
to select “Yes”, then press
.
The Data Counter is reset to zero. To cancel
resetting, select “No” at step 3, then press
.
81
Call Manager
Diverts (M 6-3)
This service is used to divert incoming calls to your
voice mail system or to another number depending on
certain conditions in which you cannot answer a call.
Divert Calls
to display the Main Menu.
1. Press
or
to select “Call Manager”,
2. Press
then press
.
3. Press
or
to select “Diverts”, then press
.
4. Select one of the divert options by pressing
or
, then press
.
The divert options available are:
• “All Calls”:
Diverts all voice calls without
ringing.
• “When Busy”: Diverts incoming calls when you are
on a call.
• “No Answer”:
Diverts incoming calls if you do
not answer a call within a
certain period of time.
• “Not Reachable”: Diverts incoming calls when your
phone is out of network service or
switched off.
.
5. Select “On”, then press
6. If you wish to divert calls to a number which is
located in the Phonebook, search for the desired
Phonebook entry.
Press
or
[Search] to search the number
by name or press
or
to search in alphabetical
order, then press
. For details on searching the
Phonebook entries, see “Finding a Name and
Number” on page 28.
7. If you wish to divert calls to a number which you
can enter manually, enter the phone number.
8. Press
.
If you select “No Answer” in step 4:
9. Enter the period of time using the digit keys (05 to
30 seconds), then press
.
Note
• When a divert is set to “All Calls”, “
on the stand-by screen.
” appears
Tip
• If you select “By Service” in step 5, you can select the
divert option further in the selected option in step 4.
Call Manager
82
Checking the Divert Status
1. Perform steps 1 to 3 in “Divert Calls” on page 82.
2. Select the divert option you wish to check by
pressing
or
, then press
.
To cancel the Divert Settings Individually
3. Press
3. Press
4. Press
or
to select “Status”, then press
.
You can now check the status of the selected divert
option.
[Back].
4. When you have finished, press
Cancelling All Divert Settings
1. Perform steps 1 to 3 in “Divert Calls” on page 82.
or
to select “Cancel All”, then press
2. Press
.
3. Press
or
to select “Yes”, then press
.
To cancel the resetting, select “No” in step 3, then
press
.
4. Press
[OK].
All divert settings are cancelled.
83
Call Manager
1. Perform steps 1 to 3 in “Divert Calls” on page 82.
2. Select the divert option you wish to cancel by
pressing
or
or
, then press
.
to select “Off”, then press
[OK].
The selected divert has been cancelled.
.
Settings
Phone Settings
Changing the Language (M 7-1-1)
You can change the display language that the phone
uses for the display messages and text entry.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
.
2. Press
.
3. Select “Phone Settings”, then press
.
4. Select “Language”, then press
or
to select the desired language, then
5. Press
press
.
Wallpaper for the Stand-by Screen (M 7-1-2)
For the stand-by screen, an animation and 3 illustrations
are provided.
Pictures taken with the digital camera or images
downloaded from a WAP site can be used for
wallpapers.
To Set Built-in Animations or Illustrations
1. Perform steps 1 to 3 in “Changing the Language”.
or
to select “Wallpaper”, then press
2. Press
.
or
to select “On”, then press
3. Press
4. Select “Animation” or “Illustration 1” to
“Illustration 3” by pressing
.
or
.
, then press
5. Press
again to set.
The selected animation or illustration is displayed
on the stand-by screen.
Note
• Even if an animation is selected, the stand-by screen
displays a static picture/image when you do not
operate the phone for about 30 seconds (It is different
according to the selected data).
Tip
• To cancel the Wallpaper setting, select “Off” in step
3.
Settings
84
To Set My Pictures for the Stand-by Screen
1. Perform steps 1 to 3 in “To Set Built-in Animations
or Illustrations” on page 84.
or
to select “My Pictures”, then press
2. Press
.
The file names of the pictures/images that are
registered in the Saved Pictures is displayed.
or
,
3. Select the picture/image by pressing
then press
.
The selected picture/image is displayed.
4. Specify the range for displaying the picture/image
by pressing
,
,
or
, then press
.
The selected picture/image is displayed on the
stand-by screen.
Note
• Some pictures/images cannot be used because of
their picture/image and data types.
Backlight (M 7-1-3)
You can turn the backlight of the main screen display
on or off when you press the keypad or the optional
cigarette lighter charger is connected to the phone.
You can change or specify the amount of time the
backlight is ON for, which will help conserve battery life.
85
Settings
To Turn On/Off the Backlight
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
or
to select “Backlight”, then press
2. Press
.
or
to select “On/Off”, then press
3. Press
4. Select “On” to set backlight on or “Off” to set
.
backlight off by pressing
or
, then press
.
When you select “On” in step 4:
5. Enter the duration of the backlight using 2 digits,
then press
.
To Turn On/Off the Backlight whilst Charging with
the Cigarette Lighter Charger
1. Perform steps 1 and 2 in “To Turn On/Off the
Backlight”.
or
to select “In Car”, then press
.
2. Press
3. Select “On” to set backlight on or “Off” to set
backlight off by pressing
or
, then press
.
Adjust the Brightness of the Backlight
(M 7-1-4)
You can adjust the brightness of the backlight of the
main screen display at four levels.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
or
to select “Brightness”, then press
2. Press
.
3. Press
(Light) or
(Dark) to adjust the
brightness for maximum clarity.
4. Press
.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
2. Press
press
or
.
to select “Display Saving”, then
3. Select “On” to set the Display Saving function on or
“Off” to set it off by pressing
or
, then press
.
When you select “On” in step 3:
4. Enter the time until the Display Saving works in two
digits (02 to 20 minutes) using the digit keys, then
press
.
Note
• The brightness of the backlight does not affect the
brightness of the Sub-Screen.
Note
• The Display Saving does not work whilst you are
calling, using WAP, or using a JavaTM application.
Display Saving (M 7-1-5)
This phone’s screen will automatically turn off after a
given amount of time if the phone is left open. This is
in order to conserve battery life.
You can change the time the Display Saving will go
into effect works between 2 and 20 minutes or disable
this function.
To Cancel the Display Saving Function
The display saving continues until either a key is
pressed or there is an incoming alert. The first key press
will only cancel the display saver. You must press
another key in order to input any numerical or text
value.
Tip
• When you purchase this phone, the Display Saving is
set to work 10 minutes later.
Settings
86
Setting the Greeting Message (M 7-1-6)
You can set the message which will appear when the
phone is turned on.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
or
to select “Greeting Message”, then
2. Press
press
.
2. Press
press
or
.
to select “Assign Pictures”, then
3. Select the screen to set the picture/image by
pressing
or
, then press
.
4. Select “Animation 1” or “Animation 2” by pressing
Up to 16 characters can be stored as a message.
For details on entering characters, see “Entering
Characters” on page 24.
or
, then press
.
or
Select “Illustration 1” or “Illustration 2” by pressing
or
, then press
when you select “Alarm”
in step 3.
The selected picture/image is displayed.
.
5. Press
Tip
• To cancel the Greeting Message setting, select “Off”
in step 3.
Tip
• To cancel the picture/image setting, select “Off” in
step 4.
or
to select “On”, then press
3. Press
.
4. Enter the message, then press
.
Assign Pictures (M 7-1-7)
Pictures/images can be displayed when turning the
power on or off, when receiving an incoming call, or
when operating the alarm.
Pictures taken by a digital camera or images
downloaded from a WAP site can be used.
To Set Built-in Pictures/Images
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
87
Settings
To Set My Pictures
1. Perform steps 1 to 3 in “To Set Built-in Pictures/
Images”.
or
to select “My Pictures”, then press
2. Press
.
The file name of the pictures/images that are
registered in the Saved Pictures is displayed.
3. Select the picture/image by pressing
or
,
then press
.
The selected picture/image is displayed.
4. Specify the range for displaying the picture/image
by pressing
,
,
or
, then press
.
Note
• Some pictures/images cannot be used because of
their picture/image and data types.
External Display (M7-1-8)
You can change the settings of the Sub-Screen Display.
To Turn On/Off the Sub-Screen Display
You can turn the Sub-Screen Display on or off when the
phone is closed.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
or
to select “External Display”,
2. Press
then press
.
3. Press
or
to select “LCD On/Off”, then press
.
4. Select “On” to set Sub-Screen Display on or “Off”
to set Sub-Screen Display off by pressing
, then press
.
or
To Turn On/Off the Backlight of the Sub-Screen
Display
You can turn the backlight of the Sub-Screen Display
on or off when the phone is closed.
You can also change or specify the duration of the SubScreen Display backlight.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
or
to select “External Display”,
2. Press
then press
.
3. Press
or
to select “Backlight”, then press
.
4. Select “On” to set backlight on or “Off” to set
backlight off by pressing
or
, then press
.
When you select “On” in step 4:
5. Enter the duration of the backlight using 2 digits,
then press
.
To Adjust the LCD Contrast of the Sub-Screen
You may sometimes need to adjust the LCD contrast of
the Sub-Screen to suit certain lighting conditions.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
Settings
88
2. Press
or
to select “External Display”,
then press
.
3. Press
or
to select “LCD Contrast”,
then press
.
4. Press
(Dark) or
(Light) to adjust the contrast
for maximum clarity.
LCD contrast can be adjusted in 9 levels.
.
5. Press
Phone Setting Reset (M 7-1-9)
The phone settings can be reset to their default settings.
1. Perform steps 1 to 3 in “Changing the Language” on
page 84.
or
to select “Set to Default”, then
2. Press
press
.
.
3. Enter your handset code, then press
or
to select “Yes”, then press
4. Press
.
To cancel resetting, select “No” in step 4, then press
.
All phone settings are reset.
Note
• If you enter a wrong handset code in step 3, operation
is cancelled.
89
Settings
Call Settings
Set various types of functions and services.
Call Waiting (M 7-2-1)
If you wish to be able to receive another incoming call
whilst you have a call in progress, you must activate the
Call Waiting service.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
or
to select “Call Settings”, then press
.
.
4. Select “Call Waiting”, then press
5. Select “On” to activate the Call Waiting service or
“Off” to deactivate it by pressing
press
.
6. Press
or
, then
[OK].
Note
• Call Waiting service may not be available on all
mobile phone networks. Contact your network
operator for more information.
To Check the Call Waiting Service Status
1. Perform steps 1 to 4 in “Call Waiting” on page 89.
or
to select “Status”, then press
.
2. Press
Now you can check the status of the Call Waiting
service.
[Back].
3. Press
Display Call Timers (M 7-2-2)
1. Perform steps 1 to 3 in “Call Waiting” on page 89.
or
to select “Display Call Timers”,
2. Press
then press
.
3. Select “On” or “Off” by pressing
press
or
, then
.
Caller No. Status (M 7-2-3)
This lets you control whether to show your phone
number or caller’s phone number when calling another
party.
Caller No. Status is not supported on all networks.
Please check with your service provider for availability.
1. Perform steps 1 to 3 in “Call Waiting” on page 89.
or
to select “Caller No. Status”, then
2. Press
press
.
3. Select the option you wish to set by pressing
, then press
The options available are:
• “Show Callers No.”: Displays whether caller
numbers are displayed or not.
• “Show Your No.”: Displays whether your phone
number is notified to your caller or not. This
function can be turned On/Off with this
option.
Select “On” to activate the option you wish to set or
“Off” to deactivate it by pressing
or
, then
press
.
• “Show Called No.”: Displays whether the phone
number of the phone you are connected to is
displayed or not, even if your call is diverted
to another phone number.
• “Hide if Called”:
Displays whether your phone
number is hidden or not from any callers.
To Check the Caller No. Status
1. Perform steps 1 to 3 in “Caller No. Status”.
or
to select “Status”, then press
2. Press
.
Now you can check the status of the Caller No.
Status.
[OK].
3. Press
or
.
Settings
90
Personal Call (M 7-2-4)
A specified ringing tone or vibrator setting can be
associated to a pre-registered phone number.
Up to 20 phone numbers can be registered.
1. Perform steps 1 to 3 in “Call Waiting” on page 89.
or
to select “Personal Call”, then press
2. Press
.
3. Select the number you wish to set by pressing
, then press
or
.
4. Enter the phone number, then press
.
If you wish to select the phone number in the
Phonebook, search for the desired Phonebook entry.
Press
or
[Search] to search the number
by name or press
or
to search in alphabetical
order, then press
. For details on searching the
Phonebook entries, see “Finding a Name and
Number” on page 28.
5. Press
press
or
.
to select “Assign Melody”, then
6. Select a ringing tone.
For details on selecting a ringing tone, see “Ringer
Type” on page 64.
7. Press
Settings
to select “Vibration”, then press
8. Press
or
to select “Enable”, “Disable” or
“Link to Sound”, then press
.
For details on setting the vibrator, see “Vibration”
on page 65.
9. When setting is complete, select “Setup End”, then
press
.
Group Call (M 7-2-5)
Phone numbers can be registered or updated in groups.
To Set Group Ringing Tone
Different ringing tones can be set for each group.
When you purchase this phone, groups are set to off.
If you do not set a group ringing tone the default ringing
tone will be used.
1. Perform steps 1 to 3 in “Call Waiting” on page 89.
or
to select “Group Call”, then press
2. Press
.
3. Select the group you want to set by pressing
or
4. Press
5. Press
press
91
or
.
, then press
.
or
to select “On”, then press
or
.
to select “Assign Melody”, then
.
6. Select a ringing tone.
For details on selecting a ringing tone, see “Ringer
Type” on page 64.
or
to select “Vibration”, then press
7. Press
.
8. Press
or
to select “Enable”, “Disable” or
“Link to Sound”, then press
.
For details on setting the vibration, see “Vibration”
on page 65.
9. When setting is complete, select “Setup End”, then
press
.
Tip
• To cancel the ringing tone setting, select “Off” in
step 4.
Auto Redial (M 7-2-6)
See “Automatic Redialling” on page 20 about this
function.
3. Press
or
to select “On” or “Off”, then press
.
Call Setting Reset (M 7-2-8)
The call settings can be reset to their default settings.
1. Perform steps 1 to 3 in “Call Waiting” on page 89.
or
to select “Set to Default”, then
2. Press
press
.
.
3. Enter your handset code, then press
or
to select “Yes”, then press
4. Press
.
To cancel resetting, select “No” at step 4, then press
.
All call settings are reset.
Note
• If you enter the wrong handset code in step 3, the
operation is cancelled and the screen returns to step
3 in “Call Waiting” on page 89.
Minute Minder (M 7-2-7)
Minute Minder function informs you of your talk time
by sounding a tone after every minute.
1. Perform steps 1 to 3 in “Call Waiting” on page 89.
or
to select “Minute Minder”, then
2. Press
press
.
Settings
92
Network Settings
Adding a New Network
Selecting a Network Automatically (M 7-3-1)
Each time the power is turned on, your phone will
always try to connect first to the most recently available
network, then to the subscribed network, and lastly to
the preferred network.
If none of these are found, it will then search for any
other available GSM networks.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
press
or
.
to select “Network Settings”, then
4. Select “Select Network”, then press
.
5. Select “Automatic”, then press
.
1. As in step 5 in “Selecting a Network
or
to select
.
2. Select the network from the list by pressing
, then press
.
Automatically”.
or
to select “Add New Network”, then
press
.
2. Press
3.
4.
5.
6.
7.
8.
9.
Press
or
to select “Add”, then press
Press
.
Enter the network code.
Press
.
Enter a new network name.
Press
[OK].
or
To Change the Position of a Network in the
Preferred List
1. Perform steps 1 to 4 in “Selecting a Network
Automatically”.
or
to select “Set Preferred”, then press
2. Press
.
3. Select the name of the network to change the
position from the list by pressing
press
.
93
Settings
.
Enter the country code.
Editing the Preferred List
To Set the Network Manually
Automatically”, press
“Manual”, then press
1. Perform steps 1 to 4 in “Selecting a Network
or
, then
4. Press
or
to select “Insert” or “Add to End”,
then press
.
To Delete a Network from the Preferred List
1. Perform steps 1 to 3 in “To Change the Position of
a Network in the Preferred List” on page 93.
or
to select “Delete”, then press
.
2. Press
Changing the Network Password (M 7-3-2)
1. Perform steps 1 to 3 “Selecting a Network
Automatically” on page 93.
2. Press
press
or
.
Internet Settings (M 7-4)
WAP/MMS Settings
WAP Settings and MMS Settings can perform
following various setups, respectively.
WAP Settings
Item
Profile Name*
to select “Change Password”, then
.
3. Enter the old password, then press
.
4. Enter a new password, then press
5. Enter a new password again, then press
.
If you enter the incorrect password in step 5, the
screen will return to step 4 and you will be asked to
enter the password again.
.
6. Press
Description
Operation
Select “Profile Name” and
WAP Profile
press
.
Name (Unique
Enter the strings you like
Name)
and press
.
Select “IP Address” and
IP Address*
IP address
press
.
Enter IP address for WAP
and press
.
Select “Homepage” and
Homepage
Homepage
press
.
Enter Homepage URL, if
needed, and press
.
Select “Port Number” and
Port Number*
Security
Option
press
.
Enter Port Number (102465535) and press
.
Settings
94
Item
Description
Circuit Prompt Circuit Prompt
Operation
Select “Circuit Prompt” and
press
.
Select “Enable” or “Disable” and press
Item
Password
Description
Password
.
Bearer Connection Type
and press
.
Select “GPRS Then CSD”,
“GPRS” or “CSD” and press
.
GPRS Settings (If “GPRS Then CSD” or “GPRS” will be
selected as connection type, they should be set)
Select “APN” and press
APN*
Access Point
Name
.
Enter Access Point Name
and press
Select “Linger Time” and
Linger Time Linger Time
User Name
99999) and press
Phone No.*
Access Point
Number
Line Type
ISDN or Analogue
press
.
Select “ISDN” or “Analogue”
and press
.
Select “UserName” and
UserName
User Name
press
.
Enter User Name and press
.
Settings
.
Select “Line Type” and
.
95
.
press
.
Enter Access Point Number and press
.
press
.
Enter User Name and press
press
.
Enter second time (0-
CSD Settings (If “GPRS Then CSD” or “CSD” will be
selected as connection type, they should be set)
Select “Phone No.” and
Select “UserName” and
UserName
press
.
Enter Password and press
.
Select “Connection Type”
Connection
Type
Operation
Select “Password” and
Item
Password
Description
Password
Operation
Select “Password” and
press
.
Enter Password and press
Item
Relay Server
URL*
Description
MMS Relay
Server
.
press
.
Enter second time (099999) and press
Port Number*
Security
Option
.
Profile Name*
Operation
Select “Profile Name” and
MMS Profile
press
.
Name (Unique
Enter the strings you like
Name)
and press
.
Select “IP Address” and
IP Address*
IP address
press
.
Enter IP address for MMS
and press
press
.
Enter Port Number (102465535) and press
.
Select “Connection Type”
MMS Settings
Description
.
Select “Port Number” and
*: Item to be set as mandatory.
Item
and press
.
Enter URL of the Relay
Server and press
Select “Linger Time” and
Linger Time Linger Time
Operation
Select “Relay Server URL”
Connection
Type
Bearer Connection Type
and press
.
Select “GPRS Then CSD”,
“GPRS” or “CSD” and press
.
GPRS Settings (If “GPRS Then CSD” or “GPRS” will be
selected as connection type, they should be set)
Select “APN” and press
APN*
Access Point
Name
.
Enter Access Point Name
and press
.
.
Settings
96
Item
UserName
Description
User Name
Operation
Select “UserName” and
press
.
Enter User Name and press
Item
UserName
Description
User Name
Operation
Select “UserName” and
press
.
Enter User Name and press
.
.
Select “Password” and
Password
Password
press
.
Enter Password and press
Select “Password” and
Password
Password
press
.
Enter Password and press
.
.
Select “Linger Time” and
Linger Time Linger Time
press
.
Enter second time (099999) and press
Linger Time Linger Time
.
CSD Settings (If “GPRS Then CSD” or “CSD” will be
selected as connection type, they should be set)
Select “Phone No.” and
Phone No.*
Access Point
Number
press
.
Enter Access Point Number and press
.
Select “Line Type” and
Line Type
ISDN or Analogue
press
.
Select “ISDN” or “Analogue”
and press
97
Settings
.
Select “Linger Time” and
press
.
Enter second time (099999) and press
*: Item to be set as mandatory.
.
To Set up your Account Information
This information should be supplied by your Internet
service provider.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
press
or
.
to select “Internet Settings”, then
4. Press
or
to select “WAP Settings” or “MMS
Settings”, then press
.
5. Select the profile name you wish to edit by pressing
or
6.
7.
8.
9.
Press
, then press
or
.
to select “Edit”, then press
.
Select the item you wish to edit, then press
.
Infrared (M 7-5)
You can use the built-in infrared modem to establish
contact between your phone and a PC equipped with an
infrared port.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
4. Press
or
to select “Infrared”, then press
.
or
to select “On”, then press
.
“ ” will appear on the screen.
The infrared setting will return to off when no data
is transmitted/received via infrared communication.
Edit each item.
When you have finished editing, select “Setup
End”, then press
.
To Select Network Connection Profile
1. Perform steps 1 to 4 in “To Set up your Account
Information”.
or
2. Select the profile name to use by pressing
, then press
.
3. Press
or
to select “Activate”, then press
.
Settings
98
Security (M 7-6)
Enabling/Disabling the PIN Code (M 7-6-1)
If the PIN code is enabled you will be asked in enter the
PIN code each time the phone is switched on. Your PIN
code is stored on the SIM and you should have been
made aware of the code when you purchased the SIM.
Contact your service provider for further details.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
.
2. Press
3. Press
4. Press
or
to select “Security”, then press
or
to select “PIN Entry”, then press
.
or
to select “On” or “Off”, then press
.
5. Press
.
6. Enter your PIN code, then press
.
Note
• If you enter the wrong PIN code three times in step 6,
the SIM will lock. To remove the lock, contact your
service provider/SIM vendor.
99
Settings
Changing PIN Code
This allows you to change the PIN code stored on the
SIM.
1. Perform steps 1 to 3 in “Enabling/Disabling the PIN
code”.
or
to select “PIN Entry”, then press
2. Press
.
3. Press
or
to select “Change PIN”, then press
.
4. Enter the existing PIN code, then press
.
5. Enter a new PIN code, then press
6. Enter a new PIN code again, then press
.
.
If you enter a code different from the code which
you entered in step 6, the screen returns to step 5.
Enter the correct code again.
Handset Lock (M 7-6-2)
The Handset Lock is an additional security feature
which prevents unauthorised use of the phone or certain
features. The default Handset Lock code is “0000”.
1. Perform steps 1 to 3 in “Enabling/Disabling the PIN
code”.
or
to select “Handset Lock”, then
2. Press
press
.
3. Press
or
to select “On” or “Off”, then press
.
4. Enter your handset code, then press
.
If you enter an incorrect handset code, the screen
will clear and you will be prompted to enter the code
again.
Changing Handset Code
The default handset code is “0000”.
1. Perform steps 1 to 2 in “Handset Lock” on page 99.
or
to select “Change Code”, then press
2. Press
.
.
3. Enter the old handset code, then press
.
4. Enter a new handset code, then press
5. Enter a new handset code again, then press
.
If you enter a code different from the code which
you entered in step 5, the screen returns to step 4.
Enter the correct code again.
Changing PIN2 Code (M 7-6-3)
PIN2 code is used to protect certain functions in the
phone such as Fixed Dialling No. and call cost limits.
The following shows you how to change PIN2 code.
1. Perform steps 1 to 3 in “Enabling/Disabling the PIN
code” on page 99.
2. Press
or
to select “Change PIN2”, then press
.
3. Enter the existing PIN2 code, then press
.
4. Enter a new PIN2 code, then press
5. Enter a new PIN2 code again, then press
.
.
If you enter a code different from the code which
you entered in step 5, the screen returns to step 4.
Enter the correct code.
Call Barring (M 7-6-4)
This function lets you place restrictions on incoming
and outgoing calls. To activate Call Barring you will
need the call barring password, which will be available
from your service provider.
1. Perform steps 1 to 3 in “Enabling/Disabling the PIN
code” on page 99.
or
to select “Call Barring”, then press
2. Press
.
3. Press
press
or
.
to select call barring option, then
Settings
100
The call barring functions available are:
• “Bar Foreign Calls”: Restricts all outgoing
international calls.
• “Only Local & Home”: Restricts all outgoing
international calls except to
your home country.
• “Bar Incoming Calls”: Restricts all incoming calls.
• “Bar Inc. if Abroad”: Restricts all incoming calls
when you are outside of the
coverage from your
registered network operator.
• “Bar Outgoing Calls”: Restricts all outgoing calls
except emergency calls.
4. Select one of the call barring options by pressing
or
, then press
.
The call barring options available are:
• “All Services”:
Restricts all services.
• “Voice Calls”:
Restricts all voice calls.
• “Data”:
Restricts all data calls.
• “Fax”:
Restricts all fax calls.
• “Messages”:
Restricts all messages.
• “All except Msgs.”:
Restricts all services except
messages.
.
5. Select “On”, then press
101
Settings
If you select “Off”, the selected call barring setting
is cancelled.
.
6. Enter the network password, then press
To change the network password, see “Changing
the Network Password” on page 94.
[OK].
7. Press
The selected call barring function is activated.
If you enter a wrong network password, the entered
password is cleared. Enter the correct the password.
Checking Call Barring Status
1. Perform steps 1 to 4 in “Call Barring” on page 100.
or
to select “Status”, then press
.
2. Press
Now you can check the status of the selected call
barring option.
3. When you finish the confirmation, press
[Back].
Cancel All Call Barring Settings
1. Perform steps 1 to 2 in “Call Barring” on page 100.
or
to select “Cancel All”, then press
2. Press
.
3. Enter the network password, then press
[OK].
4. Press
All call barring settings are cancelled.
.
To Cancel the Call Barring Setting Individually
1. Perform steps 1 to 3 in “Call Barring” on page 100.
2. Select the call barring option you wish to cancel by
pressing
or
, then press
.
or
to select “Off”, then press
3. Press
.
4. Enter the Barring password, then press
.
The selected call barring setting is cancelled.
Fixed Dialling No. (M 7-6-5)
When the Fixed Dialling No. is enabled, you can call to
only predefined numbers.
Enabling Fixed Dialling No.
1. Perform steps 1 to 3 in “Enabling/Disabling the PIN
Code” on page 99.
or
to select “Fixed Dialling No.”, then
2. Press
press
.
3. Enter a PIN2 code, then press
4. Select “Settings”, then press
.
5. Select “On”, then press
2. Press
or
to select “Edit Dial List”, then press
.
3. Press
4. Press
press
.
or
.
to select “Add New Name”, then
5. Add a name and a phone number.
For details on adding a name and a phone number,
see “Storing Names and Numbers” on page 26.
Searching a Registered Name
1. Perform steps 1 to 3 in “Adding a New Name”.
or
to select “Search”, then press
2. Press
.
3. Search for the desired name.
For details on searching a name, see “Finding a
Name and Number” on page 28.
.
.
If you select “Off”, Fixed Dialling No. is disabled.
Adding a New Name
1. Perform steps 1 to 3 in “Enabling Fixed Dialling
No.”.
Settings
102
Editing a Registered Name
1. Perform steps 1 and 2 in “Adding a New Name” on
page 102.
.
2. Select a name you wish to edit, then press
Master Reset (M 7-7)
or
to select “Edit”, then press
3. Press
4. Edit the selected name.
3. Press
.
.
The selected name will be deleted.
To cancel deletion, select “No” at step 4, then press
.
Settings
.
to select “Master Reset”, then press
.
4. Enter your handset code, then press
or
to select “Yes”, then press
5. Press
Deleting a Registered Name
1. Perform steps 1 and 2 in “Adding a New Name” on
page 102.
.
2. Select a name you wish to delete, then press
103
or
.
For details on editting a name, see “Editing
Phonebook Entries” on page 28.
or
to select “Delete”, then press
3. Press
.
4. Select “Yes”, then press
The settings can be reset to their default settings.
to display the Main Menu.
1. Press
or
to select “Settings”, then press
2. Press
.
To cancel resetting, select “No” at step 5, then press
.
All settings are reset.
Note
• If you enter a wrong handset code in step 4, operation
is cancelled.
Vodafone live!
Your phone contains a WAP browser used for surfing
on the Mobile Internet, where you can get a lot of useful
information. Normally, pages are designed for a mobile
phone.
Your phone is already setup to Vodafone site for WAP/
MMS Settings.
To Exit the WAP Browser
to exit the browser.
1. Press
Navigating a WAP Page
•
•
•
•
•
•
Viewing the WAP Browser
[
] during stand-by.
1. Press
2. Select the menu you wish to view by pressing
, then press
or
•
:
Move the highlights around in the screen.
/
: Used to select an action displayed in the
lower left corner of the screen.
:
Used to select an action displayed in the
lower right corner of the screen.
(press and hold):
Used to start the Go to URL.
to
(press and hold):
Used to start the Bookmark (WAP).
:
Exit (short press)
Turn off the phone. (press and hold)
:
Launch browser option menu.
.
Vodafone live!
104
Browser Menu
When you have started browsing, you can reach
browsing options by pressing
.
The Browser Menu contains the following:
Back:
Home:
Go to the previous screen.
Go to the homepage you set in the WAP
Settings.
Bookmarks: Add the site you are currently browsing to
your list of bookmarks, or see the list of
bookmarks.
Go to URL: Input the URL of the site you wish to go,
and go to the site.
Show URL: Display the URL you are currently
browsing.
SnapShots: Save the page you are currently browsing
to your list of Snap Shots, or see the list of
Snap Shots.
Save Items: Save images or sounds to the My Pictures
or My Sounds.
Alert Inbox: See the list of WAP push messages. You
can receive push messages via WAP
Services. This means that a service
provider sends WAP content to your
phone, without any set up.
105
Vodafone live!
Reload:
Settings:
Refresh the contents of the WAP page.
Includes “Restart Browser”, some settings,
etc.
Messages
Your phone allows you to send and receive short
messages, MMS and WAP mails.
MMS (Multimedia Messaging Service)
About MMS
MMS allows you to further personalise your messages
with pictures, sounds and animations.
Note
• Some MMS functions may not always be available
depending on your network. Contact your network
operator for more information.
6. When you finish setting, press
Press
[
] during stand-by.
Select “MMS”, then press
.
Press
or
to select “Settings”, then press
Select the desired item to set, then press
.
[Back].
Creating a New MMS (M 0-1-1)
Setting up MMS (M 0-1-5)
1.
2.
3.
4.
The items available are:
• “Roam. Download”
• “Delivery Report”
• “Delivery Rep. Allow”
• “Expiry Time”
• “Sender Visibility”
• “Anonymous Reject”
• “Slide Interval”
5. Edit the each item.
.
1.
2.
3.
4.
5.
Press
[
] during stand-by.
Select “MMS”, then press
.
Select “Compose”, then press
Enter your message, then press
.
.
Enter phone number or E-mail address of the
recipient, then press
.
If you wish to select the phone number or E-mail
address in the Phonebook, search for the desired
Phonebook entry.
Press
or
[Search] to search the number
by name or press
or
to search in alphabetical
Messages
106
order, then press
. For details on searching the
Phonebook entries, see “Finding a Name and
Number” on page 28.
6. Select “Send”, then press
.
The confirmation screen of file size is displayed.
.
7. Select “Yes”, then press
After the message has been sent, the message is
added to the Sent box.
3. Select “To” to add recipients or “Cc” to send a copy
of this MMS to other recipients by pressing
, then press
.
Note
• This phone allows you to enter up to 256 characters
as a subject, and enter up to 10 addresses of the
recipients for sending MMS.
However, these may be limited depending on your
network. In this case, you may be failed to send MMS.
Contact your network operator for more information.
To Enter the Subject of the Message
1. Perform steps 1 to 3 in “Creating a New MMS” on
page 106.
[Options] to display the Options Menu.
2. Press
.
3. Select “Subject”, then press
4. Enter the subject of your message, then press
To Add Recipients
1. Perform steps 1 to 5 in “Creating a New MMS” on
page 106.
or
to select “Add address”, then press
2. Press
.
4. Select a desired number from the list by pressing
or
Messages
.
other recipients, then press
6. Press
.
[Back] twice.
To Use the Text Template
1. Perform steps 1 to 3 in “Creating a New MMS” on
page 106
[Options] to display the Options Menu.
2. Press
3. Press
or
.
to select “Insert Template”, then
4. Select the desired template from the list by pressing
or
107
, then press
5. Enter the phone number or E-mail address of the
press
.
or
, then press
.
To Save a Message in the Drafts Box
You can save a message in the Drafts box temporarily
and send it later, without sending it immediately.
1. Perform steps 1 to 5 in “Creating a New MMS” on
page 106.
or
to select “Save”, then press
to
2. Press
save the message in the Drafts box.
Note
• You can send it later following the instructions in
“Sending a Message in the Drafts Box”.
Turning the Slide Show Setting On or Off
1. Perform steps 1 to 3 in “Creating a New MMS” on
page 106.
[Options] to display the Options Menu.
2. Press
3. Press
or
to select “Slide Show”, then press
or
to select “On” or “Off”, then press
.
4. Press
.
If You Select “On”
• You can create messages which have up to 3 slides.
Each slide can contain one picture/image, one sound
file and up to 512 characters of text (up to the
message total 30kb limit).
• The slide options available are:
Add Slide:
To add a new slide.
Delete Slide: To delete the active slide.
Previous Slide: To navigate to the previous slide.
Next Slide:
To navigate to the next slide.
• EVA data cannot be attached as a slide data to a
message.
If You Select “Off”
• You can attach a maximum of 6 pictures/images or
sounds in all.
• EVA data cannot be attached as a slide data to a
message.
Inserting Attached Data
You can send pictures/images and sounds saved in the
Saved Pictures or Saved Sounds attached to MMS.
1. Perform steps 1 to 3 in “Creating a New MMS” on
page 106.
[Options] to display the Options Menu.
2. Press
3. Press
press
or
.
to select “Picture” or “Sound”, then
4. Select the file name you wish to attach by pressing
or
, then press
.
The selected picture/sound is attached.
.
5. Press
Messages
108
To Add Attached Data
1. Perform step 1 to 3 in “Inserting Attached Data” on
page 108.
The list of attached data is displayed.
2. Select the file name you wish to add by pressing
or
, then press
[Options].
3. Press
or
to select “Add Picture” or “Add
Sound”, then press
.
4. Perform steps 4 and 5 in “Inserting Attached Data”
on page 108.
To Delete Attached Data
1. Perform steps 1 to 3 in “Inserting Attached Data” on
page 108.
The list of attached data is displayed.
2. Select the file name you wish to delete by pressing
or
, then press
[Options].
3. Press
4. Press
109
or
to select “Remove”, then press
or
to select “Yes”, then press
Messages
.
.
Sending a Message in the Drafts Box
1. Perform steps 1 and 2 in “Creating a New MMS” on
page 106.
or
to select “Drafts”, then press
.
2. Press
3. Select the desired message to send in the Drafts box
by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Send”, then press
.
4. Press
The confirmation screen of file size is displayed.
.
5. Select “Yes”, then press
The phone begins the sending process and the MMS
is sent.
Reading MMS (M 0-1-2)
Messages you receive are stored in the Inbox, and
outgoing messages are stored in the Drafts box until
you send them, after which they move to the Sent box.
Incoming Messages
The MMS indicator ( ) will appear when you are
receiving an incoming message.
1. Perform steps 1 and 2 in “Creating a New MMS” on
page 106.
or
to select “Inbox”, then press
.
2. Press
Messages are marked with “ ” denote mails with
attachments.
3. Press
or
to select the desired message, then
press
.
The message is displayed.
or
to read the
4. Scroll the screen by pressing
message.
5. When you finish viewing, press
[Done].
To Check the Sender and Receiver Phone
Number or E-mail Address
1. Perform steps 1 to 3 in “Incoming Messages” on
page 109.
[Options] to display the Options Menu.
2. Press
Replying to a Message to the Sender from Inbox
1. Perform steps 1 and 2 in “Creating a New MMS” on
page 106.
or
to select “Inbox”, then press
.
2. Press
3. Press
6.
3. Press
or
to select “Details”, then press
.
The sender’s phone number or E-mail address, time
and date stamp, subject, attachment and size are
displayed.
[Options] to display the Options Menu.
or
to select “Reply”, then press
4. Press
5. Enter your message.
7.
8.
9.
.
For details on entering characters, see “Entering
Characters” on page 24.
Press
.
The phone number or E-mail address of the
recipient is automatically filled in the sender’s
phone number or E-mail address.
Press
.
The subject field is automatically filled in with the
original subject preceded by “Re:”.
Select “Send”, then press
.
The confirmation screen of file size is displayed.
Select “Yes”, then press
.
Tip
• You can reply to a message to all addresses of
selected messages by selecting “Reply All” in step 5.
Messages
110
Forwarding a Message
1. Perform steps 1 to 3 in “Replying to a Message to
the Sender from Inbox” on page 110.
or
to select “Forward”, then press
.
2. Press
3. Enter phone number or E-mail address of the
recipient, then press
.
If you wish to select the phone number or E-mail
address in the Phonebook, search for the desired
Phonebook entry.
Press
or
[Search] to search the number
by name or press
or
to search in alphabetical
order, then press
. For details on searching the
Phonebook entries, see “Finding a Name and
Number” on page 28.
.
4. Select “Send”, then press
The confirmation screen of the file size is displayed.
.
5. Select “Yes”, then press
Note
• When the message with attached data is forwarded
the data is also sent. However, if there is any material
which the phone recognises as having copyright, it
will not be sent.
• “Subject” field is automatically filled in with the
original subject preceded by “Fw:”.
The original message and subject cannot be changed.
111
Messages
Modifying a Message
1. Perform steps 1 to 3 in “Replying to a Message to
the Sender from Inbox” on page 110.
.
2. Select “Edit”, then press
3. Modify the message.
.
4. Press
5. Select “Send”, then press
.
The confirmation screen of the file size is displayed.
.
6. Select “Yes”, then press
Note
• Messages cannot be edited if they contain particular
data such as Slide Show, XHTML, copyrights or
unknown format.
Storing the Phone Number or E-mail Address
of a Sender in the Phonebook
1. Perform steps 1 to 3 in “Replying to a Message to
the Sender from Inbox” on page 110.
or
to select “Save to Phonebook”, then
2. Press
press
.
For details on entering a name, see “Storing Names
and Numbers” on page 26.
Retrieving MMS
When “ ” is in the Inbox, the following can be done.
1. Perform steps 1 and 2 in “Creating a New MMS” on
page 106.
or
to select “Inbox”, then press
.
2. Press
3. Press
or
download.
4. Press
5. Press
to select a desired alert to
to display the Alert Menu.
or
to select “Download”, then press
.
Deleting Messages
1. Perform steps 1 and 2 in “Creating a New MMS” on
page 106.
or
to select “Inbox”, “Drafts” or
2. Press
“Sent”, then press
.
3. Select the message you wish to delete by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Delete Message”, then
4. Press
press
.
5. Press
or
to select “One Message” or “All
Messages”, then press
.
6. Select “Yes”, then press
.
To cancel deletion, select “No”, then press
Note
• You cannot delete locked messages.
.
To Lock Message
1. Perform steps 1 and 2 in “Creating a New MMS” on
page 106.
or
to select “Inbox” or “Sent”, then
2. Press
press
.
3. Select the message you wish to lock by pressing
or
, then press
[Options].
The Options Menu is displayed.
or
to select “Lock/Unlock”, then press
4. Press
.
Making a Call to the Sender of a Message
You can make a call to the sender of a message in Inbox
whose address (From) is the phone number.
1. Perform steps 1 and 2 in “Replying to a Message to
the Sender from Inbox” on page 110.
[Options] to display the Options Menu.
2. Press
3. Press
or
to select “Call”, then press
Messages
.
112
SMS (Short Message Service)
About SMS
The Short Message Service (SMS) allows you to send
text messages of up to 1024 characters to other GSM
users.
Using SMS with Your Phone
Messages longer than 160 characters may be
composed. During sending, the messages will be split.
If the receiver has a suitable phone the messages will
recombine during reception, if not your message will
appear as a number of separate 152 characters
messages.
You can send or receive SMS even if you are talking on
the phone.
You can also use My Text Templates to help you
compose SMS.
Setting up SMS (M 0-2-4)
Before you can use SMS to send and receive messages,
you have to set up some personal and system
information.
To set up the Service Centre Address
[
] during stand-by to display the
1. Press
Message menu.
or
to select “SMS”, then press
.
2. Press
113
Messages
or
to select “Settings”, then press
3. Press
.
4. Select “Message Centre”, then press
5. Enter the centre number.
.
If you wish to enter a country code for a message to
an international number, press and hold
until
a “+” sign appears.
.
6. Press
Validity Period
This indicates the number of days and hours for which
a message you send may remain undelivered to the
message recipient.
During this period, the message service centre will
continually try to deliver the message to the recipient.
1. Perform steps 1 to 3 in “Setting up SMS”.
or
to select “Message Lifetime”, then
2. Press
press
.
3. Select the validity period by pressing
then press
or
,
.
Message Format
1. Perform steps 1 to 3 in “Setting up SMS”.
or
to select “Message Format”, then
2. Press
press
.
3. Select the message format by pressing
then press
or
,
.
or
Connection Type
1. Perform steps 1 to 3 in “Setting up SMS” on page
113.
or
to select “Connection Type”, then
2. Press
press
.
3. Select the connection type by pressing
then press
or
,
.
Creating a New SMS (M 0-2-1)
[
] during stand-by.
1. Press
or
to select “SMS”, then press
2. Press
3. Select “Compose”, then press
4. Enter your message.
.
.
For details on entering characters, see “Entering
Characters” on page 24.
.
5. Press
To Use the Text Template
1. Perform steps 1 to 3 in “Creating a New SMS”.
[Options] to display the Options Menu.
2. Press
3. Press
press
or
.
4. Select the desired template from the list by pressing
to select “Insert Template”, then
, then press
.
To Save the Message in the Outbox
1. Perform steps 1 to 5 in “Creating a New SMS”.
2. Enter the SMS phone number of the recipient, then
press
3. Press
.
or
to select “Save”, then press
.
Sending a Message
1. Perform steps 1 to 5 in “Creating a New SMS”.
2. Enter the SMS phone number of the recipient, then
press
.
3. If you wish to select the SMS phone number in the
Phonebook, search for the desired Phonebook entry.
Press
or
[Search] to search the number
by name or press
or
to search in alphabetical
order, then press
. For details on searching the
Phonebook entries, see “Finding a Name and
Number” on page 28.
4. Press
or
to select “Send”, then press
.
The phone begins the sending process and the SMS
is sent.
Messages
114
Reading SMS
4. Enter your message.
Incoming Messages
The SMS indicator ( ) will appear when an incoming
message arrives.
during stand1. When you receive a SMS, press
by.
or
to select the desired message.
2. Press
The sender’s phone number and a part of the
message are displayed. When the sender’s phone
number is stored in the Phonebook, the sender’s
name is displayed instead of the phone number.
Messages are marked with “ ” denote unread
messages. If the Inbox or Outbox is full, “ ”
flashes. Delete unnecessary messages.
.
3. Press
For details on entering characters, see “Entering
Characters” on page 24.
.
5. Press
Follow the procedure from step 2 in “Sending a
Message” on page 114.
4. Scroll the screen by pressing
or
to read the
message.
5. When you have finished viewing, press
.
Replying to the Sender
1. Perform steps 1 to 3 in “Reading SMS”.
[Options] to display the Options Menu.
2. Press
3. Press
115
or
Messages
to select “Reply”, then press
.
Calling the Message Sender
1. Perform steps 1 to 3 “Reading SMS”.
[Options] to display the Options Menu.
2. Press
3. Press
or
to select “Call Sender”, then press
.
Forwarding a Message
Perform steps 1 to 3 in “Reading SMS”.
Press
[Options] to display the Options Menu.
1.
2.
3.
4.
Press
or
to select “Forward”, then press
.
Enter the SMS phone number of the recipient, then
press
.
For details on searching the Phonebook entries, see
“Finding a Name and Number” on page 28.
or
to select “Send”, then press
.
5. Press
The phone begins the sending process and the SMS
is sent.
Modifying a Message
1. Perform steps 1 and 2 in “Creating a New SMS” on
page 114.
or
to select “Outbox”, then press
.
2. Press
3. Select the desired message to modify in the Outbox
by pressing
or
, then press
.
[Options] to display the Options Menu.
4. Press
5. Select “Edit”, then press
.
6. Modify the message, then press
Extracting Phone Numbers from the Received
Messages and making a call
you can make a call using a telephone number
embedded in the received SMS message.
1. Perform steps 1 and 2 in “Reading SMS” on page
115.
[Options] to display the Options Menu.
2. Press
3. Press
or
to select “Extract Numbers”, then
press
.
Any kinds of numbers are listed.
or
to select the telephone number,
4. Press
then press
.
Follow the procedure from step 2 in “Sending a
Message” on page 114.
Deleting Messages
1. Perform steps 1 and 2 in “Creating a New SMS” on
page 114.
or
to select “Inbox” or “Outbox”, then
2. Press
press
.
5. To make a call, press
3. Select the message you wish to delete by pressing
Tip
• Selecting “Save to phonebook” in step 3 instead
allows you to go to the phone number entry prompt
with the sender’s number entered.
For details on entering a name, see“Storing Names
and Numbers” on page 26.
or
4. Press
5. Press
6. Press
, then press
.
[Options] to display the Options Menu.
or
to select “Delete”, then press
or
to select “Yes”, then press
The selected message is deleted.
.
.
.
To save this telephone number in the phonebook,
press
[Save].
For details on entering a name, see “Storing Names
and Numbers” on page 26.
Messages
116
Cell Broadcast (M 0-3)
You can receive Cell Broadcast messages or general
messages like weather reports, traffic reports, etc.
broadcast to all subscribers in a certain network area.
This function may not be available on all mobile phone
networks. Contact your network operator for more
information.
Enabling/Disabling Cell Broadcast (M 0-3-1)
1. Press
2. Press
press
[
or
.
] during stand-by.
to select “Cell Broadcast”, then
or
to select “On/Off”, then press
.
3. Press
4. Select “On” to set Cell Broadcast on or “Off” to set
it off by pressing
or
, then press
.
Reading Cell Broadcast Messages (M 0-3-2)
1. When you receive a Cell Broadcast message, press
.
or
to read the
2. Scroll the screen by pressing
message.
3. When you finish viewing, press
117
Messages
.
Subscribing to Cell Broadcasts
Select the page of the cell broadcast message that you
want.
1. Press
2. Press
press
3. Press
4. Press
press
5. Press
press
6. Press
[
or
.
] during stand-by.
to select “Cell Broadcast”, then
or
to select “Settings”, then press
or
.
to select “Set Info Subjects”, then
or
.
to select “Create Subject”, then
to add the channel.
7. Enter the appropriate channel code obtained from
your service provider, and a title for the channel.
Setting Languages
Allows you to select your preferred language for the
cell broadcast message display.
.
Cell Information (M 0-4)
The Cell Information is the message information that
operators sent to subscribers in certain areas.
When you receive Cell Information, the message will
be displayed on the stand-by screen.
Note
• This function may not be available on all mobile
phone networks. Contact your network operator for
more information.
Enabling/Disabling Cell Information
1. Press
2. Press
[
or
] during stand-by.
to select “Cell Info”, then press
or
to select “On” or “Off”, then press
.
3. Press
.
Note
• If Cell Information is set to “On”, the Stand-by Time
will decrease.
Messages
118
Data Transmission
Your PC can be set up to use the GX10 as a modem.
You can either use Infrared (IrDA) or a data cable “XN1DC10” (option) to connect to the PC.
Refer to XN-1DC10 attached manual for the
connection method of a data cable.
System Requirements
Windows®98*, Windows®Me,
Windows®2000, Windows®XP
* Windows®98 Second Edition, or Windows®98 +
Internet Explorer 5.01 or later
OS:
Interface: Infrared (IrDA) or Serial port (D-sub 9-pin
connector)
CD-ROM drive
Software Installation and Setup
1. Install Modem setup software from the included
CD-ROM.
• Insert the CD-ROM and double-click [setup.exe]
to start installation.
• Follow the instructions on the screen to complete
installation.
When installation has completed, “SHARP GSM
GPRS” icon appears in the control panel.
119
Data Transmission
When you perform the following operations (step 2
to 4), refer to GSM/GPRS Modem Option Help
after executing [SHARP GSM GPRS] in the control
panel.
2. Install Modem driver.
3. Make the Dial-up connection.
4. Set GSM/GPRS Modem Option which is stored in
the control panel.
If you wish to use GSM, fill the GSM connection
column.
If you wish to use GPRS, fill the GPRS connection
column.
Note
• Modem setup software may not run on certain PCs.
Using the Modem Setup
The software in the CD-ROM supplied is provided
based on the END USER LICENSE AGREEMENT,
and can be used and duplicated only in compliance
with the conditions of the pertinent END USER
LICENSE AGREEMENT.
The software installer displays the END USER
LICENSE AGREEMENT upon startup.
• When using the infrared modem function for
executing data transmission, align the infrared port
with each other.
Note
• The distance between the infrared ports which can
communicate is a maximum of 20 cm within a 30°
angle.
• When transmitting data via infrared communication,
you need to set the infrared setting to “On”. (p. 98)
• It is not recommended that you make or answer a call
during data transmission. The operation may be
interrupted.
Data Transmission
120
Troubleshooting
Problem
The phone does not
turn on.
PIN code or PIN2
code is rejected.
SIM card becomes
locked.
The display is difficult to read.
121
Problem
Solution
• Make sure the battery is
properly inserted and
charged.
• Make sure you have entered
the correct code (4 to 8
digits).
• Your SIM card/protected
functions will become locked
after 3 unsuccessful
attempts.
• Contact your SIM provider if
you do not have the correct
PIN code.
• Enter PUK code (8 digits)
provided by your service
provider (if supported).
• If the attempt is successful,
enter the new PIN code and
confirm your phone is
operational again. Otherwise
contact your dealer.
• Adjust the LCD contrast.
Troubleshooting
Phone functions do
not work after the
phone is turned on.
Calls cannot be
made or received.
Solution
• Check the radio signal
strength indicator as you may
be outside the service area.
• Check to see if any error
message is displayed when
you turn your phone on. If so,
contact your dealer.
• Make sure the SIM card is
correctly inserted.
• If the message “SIM Card
Error” is displayed at start-up,
you cannot use your SIM card
or SIM card is damaged.
Contact your dealer or
network service provider.
• Check your call barring, fixed
dialling setting, remaining
battery and call forwarding
settings.
• Check if your phone is
currently performing data
communication using Infrared
(IrDA) or a data cable.
• Check the remaining balance
if you are using a pre-paid
SIM card.
Problem
Call quality is poor.
Cannot access network service.
Cannot send or
receive SMS.
Cannot connect to
MMS service provider.
Solution
• Your current location may not
provide good call quality (i.e.,
in a car or train). Move to a
location where radio signal
strength is greater.
• Check where your account
has been registered and
where the service is
available.
• Make sure you are correctly
subscribed for the Short
Message Service, that the
network supports this service,
and that the centre number is
set up correctly. If not, contact
your network service
provider.
• MMS settings and
configuration may be missing
or incorrect or network does
not support it. Check your
service provider’s access
point number.
Contact your service provider
to confirm the correct
settings.
Problem
Limited memory
available.
Solution
• Delete any unnecessary data.
Troubleshooting
122
Safety Precautions and Conditions of Use
Your phone conforms to international regulations
insofar as it is used under normal conditions and in
accordance with the following instructions.
CONDITIONS OF USE
Electromagnetic waves
• Do not switch on your phone aboard an aircraft (as
your phone may interfere with the aircraft’s
electronic systems). Current legislation forbids this
use and legal action can be taken against the user.
• Do not switch on your phone in a hospital, except in
designated areas.
• Use of your phone’s function may affect the
performance of medical electronic units
(pacemakers, hearing aids, insulin pumps, etc.).
When the phone function is on, do not bring it near
medical equipment or into areas in which medical
equipment is being used. If you have a hearing aid or
a pacemaker, only use the phone on the opposite side
of your body from where it is located. The phone
should be kept at least 6 inches (15.24 cm) from a
pacemaker ANYTIME the phone is switched on.
123
Safety Precautions and Conditions of Use
• Do not switch on your phone near gas or flammable
substances.
• Observe the rules concerning the use of mobile
phones at gasoline stations, chemical plants and at all
sites where a risk of explosion exists.
Caring for your phone
• Do not allow children to use your phone without
supervision.
• Do not open or attempt to repair your phone yourself.
The product can only be repaired by authorized
service personnel.
• Do not drop your phone or subject it to severe
impacts. Bending the body and pushing the display or
keys with extreme force could damage the phone.
• Do not use solvents to clean your phone. Use only a
soft, dry cloth.
• Do not carry your phone in your back pocket as it
could break when you sit down. The display is made
of glass and is particularly fragile.
• Avoid touching the external connector on the
underside of the phone, since the delicate
components within can be damaged by static
electricity.
Battery
• Use your phone only with batteries, chargers and
accessories recommended by the manufacturer. The
manufacturer disclaims any liability for damage
caused by the use of other chargers, batteries or
accessories.
• When the battery charging alert is displayed on
the screen, charge the battery as soon as
possible. If you continue using your phone ignoring
•
•
•
•
•
the alert, the phone may cease to function, and all
data and settings you have stored may be lost at any
moment.
Before removing the battery from the phone, make
sure the phone is switched off.
Replace and charge the new battery as soon as
possible after removing the old one.
Do not touch the battery terminals. Batteries can
cause damage, injury or burns if a conductive
material touches exposed terminals. When the battery
is detached from the phone, use a cover made of nonconductive material for keeping and carrying the
battery safely.
Recommended temperature for using and storing
batteries is approximately 20°C.
The batteries’ performance is limited in low
temperatures, particularly below 0°C and the phone
may not work temporarily regardless of the amount
of remaining battery power.
• Exposing the phone to extreme temperatures will
shorten battery life.
• The battery can be charged and discharged hundreds
of times but it will eventually wear out. When the
operating time (talk-time and stand-by time) is
noticeably shorter than normal, it is time to buy a new
battery.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE,
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
See “Battery Disposal” on page 13.
Aerial Care
• Do not touch the aerial unnecessarily, whilst using
the mobile phone. If it is held, call quality may be
hindered leading to shortened talk-time and stand-by
time because the mobile phone may have to operate
on a higher power level than is necessary.
• Use only the aerial supplied or one approved by
Sharp for your mobile phone. Using unauthorised or
modified aerials may damage the mobile phone.
Moreover, since the mobile phone may violate the
appropriate regulations, it may lose performance or
exceed the limitation of SAR levels.
Safety Precautions and Conditions of Use
124
• To avoid impaired performance, do not damage the
aerial of the mobile phone.
• Whilst talking directly to the microphone, please
hold the mobile phone so that the aerial is upwards
over your shoulder.
• To avoid interfering with blasting operations, please
turn off the mobile phone in a blasting area or in a
place where a “turn off two-way radio” sign is
posted.
• Do not remove the RF cap of the back cabinet.
Camera Operation
• Learn picture quality, file formats, etc. beforehand.
The display supports up to 65,536 colours.
The taken pictures can be saved in JPEG format
(JPEG high-colour).
• Be careful not to move your hand whilst taking
pictures.
If the phone moves whilst taking a picture, the picture
can be blurred. When taking a picture, hold the phone
firmly to prevent it from moving, or use the delay
timer.
• Clean the lens cover before taking a picture.
Fingerprints, oils, etc. on the lens cover hinder clear
focusing. Wipe them off with a soft cloth before
taking a picture.
125
Safety Precautions and Conditions of Use
Others
• As with any electronic storage unit, data may be lost
or corrupted under various circumstances.
• Before connecting the phone with a PC or a
peripheral unit, read the operation manual for the
other unit carefully.
• If the phone’s battery has been removed for some
time, or the phone has been reset, the unit’s clock and
calendar may be reinitialised. The date and time
should be updated in this case.
• Use only the attached hands free kit. Some phone’s
functions may not work when unauthorised hands
free kits are used.
ENVIRONMENT
• Keep your phone away from extreme heat. Do not
leave it on the dashboard of a car or near a heater. Do
not leave it in any place that is extremely damp or
dusty.
• Since this product is not waterproof, do not use it or
store it where fluids such as water can splash onto it.
Raindrops, water spray, juice, coffee, steam,
perspiration, etc. will also cause a malfunction.
PRECAUTIONS CONCERNING
VEHICLE USE
• It is the user’s responsibility to verify if local laws
permit the use of a mobile phone in a vehicle. Give
full attention to driving. Pull off onto the side of a
road and park the car before making or answering a
call.
• If local laws permit, we recommend that you use your
phone with the attached hands free.
• Use of your phone’s function may interfere with the
vehicle’s electronic systems, such as the ABS antilock brakes or the air-bag. To ensure no such problem
occurs, please check with your dealer or car
manufacturer before connecting your phone.
• Only allow qualified service maintenance personnel
to install the vehicle accessories.
The manufacturer disclaims any liability for damage
which may result as a consequence of improper use or
use contrary to the instructions contained herein.
SAR
Your Sharp mobile phone has been designed,
manufactured and tested so as not to exceed the limits
for exposure to electromagnetic fields recommended by
the Council of the European Union. These limits are
part of comprehensive guidelines developed by
independent scientific organisations. The guidelines
include a substantial safety margin designed to assure
the safety of the phone user and others and to take into
account variations in age and health, individual
sensitivities and environmental conditions. European
standards provide for the amount of radio frequency
electromagnetic energy absorbed by the body when
using a mobile phone to be measured by reference to
the Specific Absorption Rate (SAR). The SAR limit for
the general public is currently 2 watts per kilogram
averaged over 10 grams of body tissue. Your Sharp
mobile phone SAR value is 0.56 watts per kilogram.
This has been tested to ensure that this limit is not
exceeded even when the phone is operating at its
highest certified power. In use however your Sharp
mobile phone may operate at less than full power
because it is designed to use only sufficient power to
communicate with the network.
Safety Precautions and Conditions of Use
126
Index
A
Accessories 7
B
Battery 10
Charging 13
Disposal 13
Inserting 10
Removing 12
Battery Level Indicator 14
C
Calculator 69
Rate Conversion 69
Calendar 70
Deleting Schedules 71
Find a Particular Date 70
Call 19
Answering 20
Ending 20
Holding 21
Making 19
Making Another Call During a
Call 21
Rejecting 21
Call Costs 79
127
Index
Checking Charge Limit 80
Checking Charge Rate 80
Checking Cost of Last Call 79
Checking Residual Credit 81
Checking Total Call Cost 79
Resetting All Call Costs 81
Setting Charge Limit 80
Setting Charge Rate 80
Call Log 77
Deleting 77
Sending Messages 77
Viewing 77
Call Manager 77
Call Settings 89
Auto Redial 92
Call Waiting 89
Caller No. Status 90
Display Call Timers 90
Group Call 91
Minute Minder 92
Personal Call 91
Resetting 92
Call Timers 78
Checking Duration of Last Call
78
Checking Total Call Time 78
Resetting All Call Timers 78
Call Waiting 22, 89
Camera 9, 34
Brightness 36
Deleting 37
Indicators 35
Memory 35
Mode 35
Picture Size 34
Retaking Pictures 35
Sending 37
Taking Pictures 34
Timer 36
Viewing 36
Zoom Function 34
Cell Broadcast 117
Enabling/Disabling 117
Reading 117
Setting Languages 117
Subscribing 117
Cell Information 118
Enabling/Disabling 118
Clock & Alarm 71
Changing Alarm Settings 75
Disabling Alarm Function 75
Resetting Alarm Setting 75
Resetting All Alarm Settings 75
Setting Alarm 73
Setting Date and Time 71
Setting Time Zone 73
Clock Setting 71
Setting Date and Time 71
Conference Call 22
Adding New Participants 23
Ending Call with a Participant
23
Making 22
Private Conversation 23
D
Data Counter 81
Resetting 81
Data Transmission 119
Modem Setup 119
Software Installation/Setup 119
System Requirements 119
Diverts 82
Cancelling All Divert Settings
83
Cancelling Divert Settings Individually 83
Checking Divert Status 83
Divert Calls 82
WAP/MMS Settings 94
E
J
Earpiece 9
Earpiece Volume 21
Emergency Calls 19
End/Power Key 9
Entering Characters 24
Changing Input Mode 25
Symbols and Punctuation 25
T9 Text Input 25
Table of Characters 24
Text Template 25
External Connector 9
Java™ 38
Downloading 38
Java™ Games 48
Clearing All Applications 50
Downloading 51
Information 51
Online Services 50
Resetting 50
Settings 48
F
M
Fun & Games 48
H
Hands free Connector 9
Help List 76
I
Indicators 15
Main Screen 15
Sub-Screen 17
Infrared 98
Infrared Port 9
International Calls 19
Internet Settings 94
L
LED Indicator 9
M Key 9
Main Screen Display 9
Master Reset 103
Melody Editor 52
Copying/Pasting Notes 59
Creating Your Original Ringing
Tone 52
Deleting 57
Editing 57
Musical Scale/Rest 54
Strength 57
Tone 55
Index
128
Types of Notes/Rests 54
Memory Status 47
Menu 32
List of Menu Functions 33
Main Menu 32
Operation Guidance 32
Shortcut Keys 32
Side Keys 32
Menu Key 32
Messages 106
MMS 106
SMS 113
Microphone 9
Muting 23
Mirror 9
MMS 106
Adding Recipients 107
Check the Sender and Receiver
Phone Number or E-mail
Address 110
Creating 106
Deleting 112
Extracting Phone Numbers 116
Forwarding 111
Inserting Attached Data 108
Lock/Unlock 112
Making a Call 112
129
Index
Modifying 111
Reading 109
Replying 110
Retrieving 112
Saving in Drafts Box 108
Sending Message in Drafts Box
109
Setting up 106
Storing the Phone Number or Email Address of a Sender
in the Phonebook 111
Turning the Slide Show Setting
On or Off 108
My Bookmarks 45
Accessing 45
Adding 45
Deleting 46
Editing 46
My Java™ Games 39
Checking Information 39
Deleting 40
Ending 39
Executing 39
Suspending 39
My Phone 38
My Pictures 40
Adjusting Size 41
Changing File Name 41
Checking 41
Deleting 42
Downloading 40
Sending Messages 42
Viewing 41
My Sounds 43
Changing File Name 44
Checking 43
Deleting 45
Downloading 43
Playing Back 43
Sending Messages 44
Strength 44
Tone 44
My Text Templates 46
Adding Phrases 46
Deleting 47
Editing 46
Using 25, 107, 114
Viewing 47
N
Navigation Keys (Arrow Keys) 9,
32
Network Settings 93
Adding New Network 93
Changing Network Password 94
Editing Preferred List 93
Selecting a Network Automatically 93
O
Organiser 69
Other Games 51
Setting up Game Options 52
Starting 51
P
Phone Settings 84
Assign Pictures 87
Backlight 85
Brightness of Backlight 86
Built-in Animations/Illustrations 84
Changing Language 84
Display Saving 86
External Display 88
Greeting Message 87
Resetting 89
Wallpaper 84
Phonebook 24
Adding Number from Call Log
27
Creating New Entry 25
Deleting 29
Editing 28
Group Name 24, 26
Memory Status 30
Searching 28
Sending Messages 31
Storing Inputted Number 27
View Groups 29
Your Own Number 29
PIN Code 99
PIN2 Code 100
Profiles 63
Activating 63
Any Key Answer 68
Customising 63
Keypad Tones 65
Low Battery Alert 68
Message Alert 67
Power On/Off Sound 66
Resetting 64
Ringer Type 64
Ringer Volume 64
Vibration 65
Warning Tone 66
Q
Quick Reference 132
R
Redialling 20
Auto Redial 20
S
SAR 126
Security 99
Call Barring 100
Changing Handset Code 100
Changing PIN Code 99
Changing PIN2 Code 100
Enabling/Disabling PIN code 99
Fixed Dialling No. 102
Handset Lock 99
Settings 84
Call Settings 89
Infrared 98
Network Settings 93
Phone Settings 84
Security 99
SIM Card 10
Inserting 10
Removing 12
SMS 113
Calling 115
Creating 114
Deleting 116
Index
130
Forwarding 115
Modifying 116
Reading 115
Replying 115
Saving in Outbox 114
Sending 114
Setting up 113
Storing Sender’s Number in
Phonebook 116
Speaker 9
Speed Dialling 19, 30
T
Tone Editor 59
Algorithm 60
Creating Your Original Tone 61
Effect Frequency 61
FM Sound Source 59
Operator 60
Troubleshooting 121
Turning Your Phone On/Off 15
V
Vodafone live! 104
Browser Menu 105
Navigating WAP Page 104
Viewing WAP Browser 104
Voice Memo 75
131
Index
Playing Back 76
Recording 75
ENGLISH
Quick Reference
GX10
Quick Reference
132
133
Quick Reference
Kurzanleitung
GX10
DEUTSCH
Quick Reference
134
135
Quick Reference
Guida di consultazione
rapida-GX10
ITALIANO
Quick Reference
136
137
Quick Reference
ESPAÑOL
Referencia rápida
GX10
Quick Reference
138
139
Quick Reference
Beknopt overzicht
GX10
NEDERLANDS
Quick Reference
140
141
Quick Reference