Cisco 7000 and 7507 Chassis MAS-7K Specifications

PA-2FE-TX and PA-2FE-FX Two-Port Fast
Ethernet Port Adapter Installation and
Configuration
Product Number: PA-2FE-TX=, PA-2FE-FX=
Platforms Supported: Cisco 7100 Series Routers, Cisco 7200 Series Routers,
Cisco uBR7200 Series Routers, Cisco 7200 VXR Routers, Cisco 7201 Router,
Cisco 7301 Router, Cisco 7304 PCI Port Adapter Carrier Card in the Cisco 7304
Router, Cisco 7401ASR Router, and VIP in the Cisco 7500 Series Routers
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-3474-07
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems,
Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press,
Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing,
FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys,
MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StackWise, The Fastest Way to Increase
Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0704R)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
© 2007 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
vii
Document Revision History
Objectives
Organization
vii
viii
viii
Related Documentation
viii
Obtaining Documentation, Obtaining Support, and Security Guidelines
CHAPTER
1
Overview
1-1
Port Adapter Overview
1-1
Fast Ethernet Overview
1-2
IEEE 802.3u 100BASE-T Specifications
LEDs
xi
1-2
1-4
Receptacles, Cables, and Pinouts
Network Management
1-4
1-6
Port Adapter Slot Locations on the Supported Platforms 1-7
Cisco 7100 Series Routers Slot Numbering 1-7
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot Numbering
Cisco uBR7200 Series Router Slot Numbering 1-9
Cisco 7201 Router Slot Numbering 1-10
Cisco 7301 Router Slot Numbering 1-10
Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering 1-11
Cisco 7401ASR Router Slot Numbering 1-12
Cisco 7500 Series Routers with VIP Slot Numbering 1-12
1-8
Identifying Interface Addresses 1-16
Cisco 7120 Router and Cisco 7140 Router Interface Addresses 1-17
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses
Cisco uBR7200 Series Routers Interface Addresses 1-18
Cisco 7201 Router Interface Addresses 1-18
Cisco 7301 Router Interface Addresses 1-18
Cisco 7304 PCI Port Adapter Carrier Card Interface Addresses 1-18
Cisco 7401ASR Router Interface Addresses 1-18
Cisco 7500 Series Routers VIP Interface Addresses 1-19
1-17
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
iii
Contents
CHAPTER
2
Preparing for Installation
2-1
Required Tools and Equipment
2-1
Software and Hardware Requirements
Checking Hardware and Software Compatibility
2-2
Safety Guidelines 2-3
Safety Warnings 2-3
Warning Definition 2-3
Electrical Equipment Guidelines 2-8
Telephone Wiring Guidelines 2-9
Preventing Electrostatic Discharge Damage
2-9
FCC Class A Compliance
CHAPTER
3
2-2
2-10
Removing and Installing Port Adapters
Handling Port Adapters
3-1
Online Insertion and Removal
Warnings and Cautions
3-1
3-2
3-3
Port Adapter Removal and Installation 3-4
Cisco 7100 Series—Removing and Installing a Port Adapter 3-5
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and Installing a Port
Adapter 3-6
Cisco uBR7200 Series Routers—Removing a Port Adapter 3-7
Cisco uBR7200 Series Routers—Installing a Port Adapter 3-8
Cisco 7201 Router—Removing and Installing a Port Adapter 3-9
Cisco 7301 Router—Removing and Installing a Port Adapter 3-10
Cisco 7304 PCI Port Adapter Carrier Card—Removing and Installing a Port Adapter 3-11
Cisco 7401ASR Router—Removing and Installing a Port Adapter 3-13
Cisco 7500 Series Router VIP—Removing and Installing a Port Adapter 3-13
Removing and Installing a VIP Carrier Card in the Cisco 7500 Series Router 3-14
Removing and Installing the Port Adapter in the VIP Carrier Card 3-15
Connecting a PA-2FE RJ-45 or SC Cable
CHAPTER
4
Configuring the PA-2FE
3-16
4-1
Using the EXEC Command Interpreter
4-1
Configuring the Interfaces 4-2
Shutting Down an Interface 4-2
Performing a Basic Interface Configuration
4-7
Checking the Configuration 4-9
Using show Commands to Verify the New Interface Status
4-9
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
iv
OL-3474-07
Contents
Using the show version or show hardware Commands 4-11
Using the show diag Command 4-14
Using the show interfaces Command 4-18
Using the ping Command to Verify Network Connectivity 4-21
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
v
Contents
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
vi
OL-3474-07
Preface
This preface describes the objectives and organization of this document and explains how to find
additional information on related products and services. This preface contains the following sections:
•
Document Revision History, page vii
•
Objectives, page viii
•
Organization, page viii
•
Related Documentation, page viii
•
Obtaining Documentation, Obtaining Support, and Security Guidelines, page xi
Document Revision History
The Document Revision History table below, beginning with version OL-10589-05, records technical
changes to this document.
Document Version
Date
Change Summary
OL-3474-07
April, 2007
Adding Cisco 7201 router information.
OL-3474-06
December, 2006
Correcting software support information.
OL-3474-05
November, 2006
Correcting the RJ-45 pinout information.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
vii
Preface
Objectives
Objectives
This document describes how to install and configure the PA-2FE-TX and PA-2FE-FX two-port Fast
Ethernet port adapters, hereafter referred to as the PA-2FE, which are used in the following platforms:
•
Cisco 7100 series routers, consisting of the Cisco 7120 series and Cisco 7140 series
•
Cisco 7200 series routers and Cisco 7200 VXR routers, consisting of the two-slot Cisco 7202,
four-slot Cisco 7204 and Cisco 7204VXR, and the six-slot Cisco 7206 and Cisco 7206VXR
•
Cisco uBR7200 series universal broadband routers
•
Cisco 7201 router
•
Cisco 7301 router
•
Cisco 7304 PCI port adapter carrier card in Cisco 7304 router
•
Cisco 7401ASR router
•
Versatile Interface Processor (VIP) in Cisco 7500 series routers (VIP2, VIP4, VIP6-80)
Organization
This document contains the following chapters:
Section
Title
Description
Chapter 1
Overview
Describes the PA-2FE and its LED displays, cables, and
receptacles.
Chapter 2
Preparing for Installation
Describes safety considerations, tools required, and
procedures you should perform before the actual
installation.
Chapter 3
Removing and Installing
Port Adapters
Describes the procedures for installing and removing
PA-2FE port adapters in the supported platforms.
Chapter 4
Configuring the PA-2FE
Provides instructions for configuring the PA-2FE on the
supported platforms.
Related Documentation
Your router and the Cisco IOS software running on it contain extensive features and functionality, which
are documented in the following resources:
•
Cisco IOS software:
For configuration information and support, refer to the modular configuration and modular
command reference publications in the Cisco IOS software configuration documentation set that
corresponds to the software release installed on your Cisco hardware.
Note
You can access Cisco IOS software configuration and hardware installation and maintenance
documentation on the World Wide Web at http://www.cisco.com,
http://www-china.cisco.com, or http://www-europe.cisco.com.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
viii
OL-3474-07
Preface
Related Documentation
•
Cisco 7100 series routers:
– For an online directory to quickly access documents for Cisco 7100 series routers, refer to the
Cisco 7100 Series Documentation roadmap at the following URL:
http://www.cisco.com/en/US/products/hw/vpndevc/ps333/products_product_index09186a008
00fa142.html
– For hardware installation and configuration information refer to the Cisco 7100 Series VPN
Router Installation and Configuration Guide.
•
Cisco 7200 series routers:
– For an online directory to quickly access documents for Cisco 7200 series routers, refer to the
Cisco 7200 Series Routers Documentation Roadmap at the following URL:
http://www.cisco.com/en/US/products/hw/routers/ps341/products_documentation_roadmap09
186a00801c0915.html
– For hardware installation and configuration information (including the Cisco 7206 or
Cisco 7206VXR as a router shelf in a Cisco AS5800 Universal Access Server), refer to the
online installation and configuration guide and quick start for your Cisco 7200 series router.
– For port adapter hardware and memory configuration guidelines, refer to the Cisco 7200 Series
Port Adapter Hardware Configuration Guidelines.
– For information on network processing engines or network services engines, refer to the
Network Processing Engine and Network Services Engine Installation and Configuration
document.
•
Cisco 7200 VXR routers:
– For an online directory to quickly access documents for Cisco 7200 VXR routers, refer to the
Cisco 7200 Series Routers Documentation Roadmap at the following URL:
http://www.cisco.com/en/US/products/hw/routers/ps341/products_documentation_roadmap09
186a00801c0915.html
– For hardware installation and maintenance information, refer to the Cisco 7200 VXR
Installation and Configuration Guide or the Cisco 7200 VXR Routers Quick Start Guide.
– For more information about the Cisco 7206 or the Cisco 7206VXR as a router shelf, see the
Cisco AS5800 Series Universal Gateways documents at the following URL:
http://www.cisco.com/en/US/products/hw/univgate/ps509/tsd_products_support_series_home.
html
•
Cisco uBR7200 series routers:
– For an online directory to quickly access documents for Cisco uBR7200 Universal Broadband
routers, refer to the Cisco uBR7200 Universal Broadband Router Documentation Roadmap at
the following URL:
http://www.cisco.com/en/US/products/hw/cable/ps2217/products_documentation_roadmap09
186a00805e0d0c.html
•
Cisco 7201 router:
– For an online directory to quickly access documents for the Cisco 7201 router, refer to the
Cisco 7201 Router Documentation Roadmap at the following URL:
http://www.cisco.com/en/US/customer/products/hw/routers/ps341/products_documentation_r
oadmap09186a00807f635a.html
– For hardware installation and maintenance information, refer to the Cisco 7201 Installation and
Configuration Guide or the Cisco 7201 Router Quick Start Guide.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
ix
Preface
Related Documentation
•
Cisco 7301 router:
– For an online directory to quickly access documents for the Cisco 7301 router, refer to the
Cisco 7301 Internet Router Documentation Roadmap at the following URL:
http://www.cisco.com/en/US/products/hw/routers/ps352/products_documentation_roadmap09
186a00801c0f21.html
– For hardware installation and maintenance information, refer to the Cisco 7301 Installation and
Configuration Guide or the Cisco 7301 Router Quick Start Guide.
•
Cisco 7304 PCI port adapter carrier card in Cisco 7304 router:
– For an online directory to quickly access documents for the Cisco 7304 PCI Port Adapter
Carrier Card in the Cisco 7301 router, refer to the Cisco 7304 Router Line Card, Carrier Card,
Port Adapter, Modular Services Card, and Shared Port Adapter Documentation Roadmap at the
following URL:
http://www.cisco.com/en/US/products/hw/routers/ps352/products_documentation_roadmap09
186a00801c0f5e.html
– For hardware installation and maintenance information, refer to the Cisco 7304 PCI Port
Adapter Carrier Card Installation and Configuration Guide.
•
Cisco 7401ASR router:
– For an online directory to quickly access documents for the Cisco 7401ASR router, refer to the
Cisco 7401ASR Router Documentation Roadmap at the following URL:
http://www.cisco.com/en/US/products/hw/routers/ps354/products_documentation_roadmap09
186a00801c0fd5.html
– For hardware installation and maintenance information, refer to the Cisco 7401ASR Installation
and Configuration Guide or the Cisco 7401ASR Router Quick Start Guide.
•
Cisco 7500 series routers
– For an online directory to quickly access documents for the Cisco 7500 series routers, refer to
the Cisco 7500 Series Routers Documentation Roadmap at the following URL:
http://www.cisco.com/en/US/products/hw/routers/ps359/products_documentation_roadmap09
186a00801c0f9b.html
– For hardware installation and maintenance information, refer to the Cisco 7500 Series
Installation and Configuration Guide or the quick start for your Cisco 7500 series router.
•
For international agency compliance, safety, and statutory information for WAN interfaces, refer to
the following documents. Use the documentation roadmap for your particular router to link to the
appropriate documents for your router:
– Regulatory Compliance and Safety Information for Cisco 7100 Series VPN Routers
– Regulatory Compliance and Safety Information for Cisco 7200 Series Routers
– Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal
Broadband Routers
– Regulatory Compliance and Safety Information for the Cisco 7301 Internet Router
– Regulatory Compliance and Safety Information for the Cisco 7304 Internet Router
– Regulatory Compliance and Safety Information for the Cisco 7401ASR Internet Router
– Regulatory Compliance and Safety Information for the Cisco 7500 Series Routers
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
x
OL-3474-07
Preface
Obtaining Documentation, Obtaining Support, and Security Guidelines
•
Fast Ethernet Port Adapter Family (PA-FE and PA-2FE) Datasheet
http://www.cisco.com/en/US/products/hw/modules/ps2033/products_data_sheet09186a0080091c9
2.html
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback,
security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s
New in Cisco Product Documentation, which also lists all new and revised technical documentation at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
xi
Preface
Obtaining Documentation, Obtaining Support, and Security Guidelines
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
xii
OL-3474-07
C H A P T E R
1
Overview
This chapter describes the PA-2FE port adapter and contains the following sections:
•
Port Adapter Overview, page 1-1
•
Fast Ethernet Overview, page 1-2
•
IEEE 802.3u 100BASE-T Specifications, page 1-2
•
LEDs, page 1-4
•
Receptacles, Cables, and Pinouts, page 1-4
•
Network Management, page 1-6
•
Port Adapter Slot Locations on the Supported Platforms, page 1-7
•
Identifying Interface Addresses, page 1-16
Port Adapter Overview
The PA-2FE provides two 10/100-Mbps, 10/100BASE-T Fast Ethernet/Inter-Switch Link (ISL)
interfaces and supports both full-duplex and half-duplex operation. Refer to the “Fast Ethernet
Overview” section on page 1-2 for additional information.
Both models of the PA-2FE (PA-2FE-TX and PA-2FE-FX) are shown in Figure 1-1 and Figure 1-2.
Figure 1-1
PA-2FE-TX—Faceplate View
PA-2FE-TX
ED
L
AB
EN
0
NK
0
TX
RX
0
RX
1
K1
1
LIN
1
LIN
TX
1
46453
0
LI
Figure 1-2
PA-2FE-FX—Faceplate View
LI
0
NK
T
X0
R
X0
RX
TX
1
RX
TX
RX
1
TX
K1
46454
D
0
E
LE
CL
A
PR SS
PROD 1 LE
U
DEOD KT D P
U
CL IT MIT RO
AS AV K DU
SE EC LA CT
PR
S
1 VO SE
O
DU
YA 1
NT LE
CT
O
DE D
LE
L
D
DE
CL
AS
E
1
PA-2FE-FX
B
NA
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-1
Chapter 1
Overview
Fast Ethernet Overview
Fast Ethernet Overview
The term Ethernet is commonly used for all carrier sense multiple access collision detect (CSMA/CD)
LANs that generally conform to Ethernet specifications, including Fast Ethernet under IEEE 802.3u.
Note
100BASE-TX is intended for Environment A, and 100BASE-FX is intended for Environment B. Both
are described in the IEEE 802.3u standard.
IEEE 802.3u is well suited to applications where a local communication medium must carry sporadic,
occasionally heavy traffic at peak data rates. Stations on a CSMA/CD LAN can access the network at
any time. Before sending data, the station listens to the network to see if it is already in use. If it is in
use, the station waits until the network is not in use, then transmits. This process is known as half-duplex
operation. A collision occurs when two stations listen for network traffic, hear none, and transmit almost
simultaneously. When simultaneous transmission occurs, both transmissions are damaged and the
stations must retransmit. The stations detect the collision and use backoff algorithms to determine when
they should retransmit.
Both Ethernet and IEEE 802.3u are broadcast networks, which means that all stations see all
transmissions. Each station must examine received frames to determine whether it is the intended
destination and, if it is, pass the frame to a higher protocol layer for processing.
IEEE 802.3u specifies the following different physical layers for 100BASE-T:
•
100BASE-TX—100BASE-T, half- and full-duplex over Category 5 UTP, EIA/TIA–568-compliant
cable
•
100BASE-FX—100BASE-T, half- and full-duplex over optical fiber
Each physical layer protocol has a name that summarizes its characteristics in the format speed/signaling
method/segment length, where speed is the LAN speed in megabits per second (Mbps), signaling method
is the signaling method used (either baseband or broadband), and segment length is the maximum length
between stations in hundreds of meters. Therefore, 100BASE-T specifies a 100-Mbps, baseband LAN
with maximum network segments.
IEEE 802.3u 100BASE-T Specifications
This section provides specifications for IEEE 802.3u 100BASE-T. Table 1-1 provides cabling
specifications for 100BASE-TX Fast Ethernet transmission over UTP and foil twisted-pair (FTP), and
100BASE-FX Fast Ethernet over fiber-optic cables. It also summarizes IEEE 802.3u 100BASE-TX and
100BASE-FX physical characteristics. (See Figure 1-3.)
Table 1-1
Cabling Specifications
Parameter
100BASE-TX
1
100BASE-FX (Multimode)
2
Cable specification
Category 5 UTP , 22 to 24
AWG
62.5/125 multimode optical fiber
Maximum segment length
(half-duplex)3
100 m
412 m
Maximum segment length
(full-duplex)3
100 m
2000 m
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-2
OL-3474-07
Chapter 1
Overview
IEEE 802.3u 100BASE-T Specifications
Table 1-1
Cabling Specifications (continued)
Parameter
100BASE-TX
100BASE-FX (Multimode)
Maximum network length
(half-duplex, one repeater)4
200 m
272 m
Data rate
100 Mbps
100 Mbps
Signaling method
4B/5B5 block coded, scrambled, 4B/5B block coded, with NRZI
with MLT-3 line coding
line coding
Connector
RJ-45 (ISO/IEC 60603-7:-1990
SC-type: dual simplex or single
duplex for RX and TX
Topology
Star/hub
Star/hub
1. EIA/TIA-568 or EIA-TIA-568 TSB-36 compliant.
2. Cisco does not supply Category 5 UTP RJ-45 cables. However, they are available commercially.
3. Data Terminal Equipment (DTE to DTE), see Figure 1-3.
4. DTE to Repeater to DTE, see Figure 1-3.
5. 4B/5B encoding or block coding, encodes four data bits into a 5-bit transmission sequence.
Figure 1-3
Maximum Segment and Network Lengths—100BASE--FX and 100BASE-TX
Maximum segment length, full duplex
100 m TX
DTE*
DTE
2000 m FX–multimode
Maximum segment length, full duplex
10,000 m FX–single mode
DTE
DTE
Maximum segment length, half duplex
100 m TX
DTE
DTE
412 m FX
Maximum network length, half duplex
DTE
200 m TX
R
(Repeater)
DTE
**Because repeaters have more delay, total network length is shorter.
31703
272 m FX**
*DTE = Data Terminal Equipment
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-3
Chapter 1
Overview
LEDs
Note
PA-2FE-FX uses 62.5/125-micron multimode fiber with an SC connector.
LEDs
The PA-2FE has seven LEDS; an ENABLED LED, and LINK, TRANSMIT, and RECEIVE LEDs for
each port. The LEDs are shown in Figure 1-4.
Figure 1-4
PA-2FE LEDs—Faceplate View of PA-2FE-TX
PA-2FE-TX
D
LE
B
NA
0
T
X0
0
RX
RX
1
TX
1
K1
LIN
1
46453
0
E
K
LIN
After system initialization, the ENABLED LED goes on to indicate that the PA-2FE is ready for
operation. The following conditions must be met before the ENABLED LED goes on:
•
The PA-2FE is correctly connected and receiving power.
•
A PA-2FE–equipped card or chassis contains a valid microcode version that has been successfully
downloaded.
•
The bus recognizes the PA-2FE.
If any of these conditions are not met, or if the initialization fails for other reasons, the ENABLED LED
does not go on. Table 1-2 lists LED colors and indicator functions.
Table 1-2
PA-2FE LEDs
LED Label
Color
State
Function
ENABLED
Green
On
Port adapter is enabled for operation.
LINK0
Green
On
Port 0 is receiving a carrier signal from the network.1
TX0
Green
On
Port 0 is transmitting data.
RX0
Green
On
Port 0 is receiving data.
RX1
Green
On
Port 1 is receiving data.
TX1
Green
On
Port 1 is transmitting data.
LINK1
Green
On
Port 1 is receiving a carrier signal from the network.1
1. When an RJ-45 or SC port is active.
Receptacles, Cables, and Pinouts
The two interface receptacles on the PA-2FE are a single RJ-45 connection (on the PA-2FE-TX) or an
SC-type optical-fiber connection (on the PA-2FE-FX). Each connection supports IEEE 802.3u interfaces
compliant with the 100BASE-X and 10/100BASE-T standards. The RJ-45 connection does not require
an external transceiver.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-4
OL-3474-07
Chapter 1
Overview
Receptacles, Cables, and Pinouts
Figure 1-5 shows the RJ-45 cable connectors. Cisco does not supply Category 5 UTP RJ-45 cables; they
are available from a commercial supplier. Table 1-3 lists the pinouts and signals for the PA-2FE-TX
RJ-45 connectors.
Figure 1-5
RJ-45 Port and Connector
1
1
84529
12345678
RJ-45 connector and port
Table 1-3
IRJ-45 Port Pinout Information
Pin
Description
1
TxD+1
2
TxD–
3
RxD+2
6
RxD–
1. TxD = Transmit data
2. RxD = Receive data
Note
Referring to the RJ-45 pinout in Table 1-3, proper common-mode line terminations should be used for
the unused Category 5, UTP cable pairs 4/5 and 7/8. Common-mode line termination reduces the
contributions to electromagnetic interference (EMI) and susceptibility to common-mode sources. Wire
pairs 4/5 and 7/8 are passively terminated in the RJ-45 100BASE-TX port circuitry in the PA-2FE-TX.
Depending on your RJ-45 interface cabling requirements, use the pinouts in Figure 1-6 and Figure 1-7.
Ethernet port
Straight-Through Cable Pinout—PA-2FE-TX RJ-45 Connection to a Hub or Repeater
Hub
1 TxD+
2 TxD–
1 RxD+
2 RxD–
3 RxD+
6 RxD–
3 TxD+
6 TxD–
38582
Figure 1-6
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-5
Chapter 1
Overview
Network Management
Crossover Cable Pinout—PA-2FE-TX RJ-45 Connections Between Hubs and Repeaters
Ethernet port
DTE
1 TxD+
1 TxD+
2 TxD–
2 TxD–
3 RxD+
3 RxD+
6 RxD–
6 RxD–
38583
Figure 1-7
Figure 1-8 shows the duplex SC connector (one required for both transmit and receive), and Figure 1-9
shows the simplex SC connector (two required, one each for transmit and receive) used for PA-2FE-FX
optical-fiber connections. Cisco does not supply these multimode optical-fiber cables; they are available
from a commercial supplier.
PA-2FE-FX Duplex SC Connector
Figure 1-9
PA-2FE-FX Simplex SC Connector
H2399
H2214
Figure 1-8
Network Management
The PA-2FE supports the following:
•
SNMP agent v1 (RFC 1155–1157)
•
Ethernet MIB (RFC 1398)
•
IEEE 802.3 LAN specification for CSMA/CD
•
MIB for Network Management of TCP/IP-Based Internets: MIB-II (RFC 1213)
•
Definition of Managed Objects for Bridges (RFC 1493)
•
Evolution of Interfaces Group of MIB-II (RFC 1573)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-6
OL-3474-07
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Port Adapter Slot Locations on the Supported Platforms
This section discusses port adapter slot locations on the supported platforms. The illustrations that
follow summarize slot location conventions on each platform:
Note
•
Cisco 7100 Series Routers Slot Numbering, page 1-7
•
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot Numbering, page 1-8
•
Cisco uBR7200 Series Router Slot Numbering, page 1-9
•
Cisco 7201 Router Slot Numbering, page 1-10
•
Cisco 7301 Router Slot Numbering, page 1-10
•
Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering, page 1-11
•
Cisco 7401ASR Router Slot Numbering, page 1-12
•
Cisco 7500 Series Routers with VIP Slot Numbering, page 1-12
The port adapters shown in the slot identification illustrations may not be the same port adapter that is
documented in this guide.
Cisco 7100 Series Routers Slot Numbering
The PA-2FE can be installed in port adapter slot 3 in Cisco 7120 series routers, and in port adapter slot 4
in Cisco 7140 series routers. Figure 1-10 shows the slot numbering on a Cisco 7120 series router.
Figure 1-11 shows the slot numbering on a Cisco 7140 series router.
Figure 1-10
Port Adapter Slots in the Cisco 7120 Series Router
Slot 5
Slot 3
Slot 4
SLOT 0
SLOT 1
PWR
ACT ACT
0
FE 0 / 0
I
E3
EN
TX
FE
0/1
LNK LNK
0
1
CONS
AUX
SYS
RDY
RX
RX
2
CEL CAR ALM
7120 - AE3
Slot 1
Slot 0
18498
5
Slot 2
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-7
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Figure 1-11
Port Adapter Slots in the Cisco 7140 Series Router
Slot 5
Slot 3
Slot 4
AC OK
DC OK
OTF
RESET
PWR
ACT ACT
EN
5
0
FE 0 / 0
I
SLOT 1
EN
RX
RX
155 - MM
TX
FE 0 / 1
LNK LNK
0
1
RX
EN
CEL CAR ALM
CONS
155 - MM
RX
TX
AC OK
SYS
RDY
DC OK
OTF
2
CEL CAR ALM
7140 - 2MM3
Slot 0
Slot 1
AUX
18499
SM-ISM
SLOT 0
BOOT
ERROR
Slot 2
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot Numbering
Cisco 7202 routers have two port adapter slots. The slots are numbered from left to right. You can place
the port adapters in either of the slots (slot 1 or slot 2). The Cisco 7202 router is not shown.
Cisco 7204 routers and Cisco 7204VXR routers have four slots for port adapters, and one slot for an
input/output (I/O) controller. The slots are numbered from the lower left to the upper right, beginning
with slot 1 and continuing through slot 4.You can place the port adapters in any of the slots (slot 1
through slot 4). Slot 0 is always reserved for the I/O controller. The Cisco 7204 router and Cisco
7204VXR are not shown
Cisco 7206 routers and Cisco 7206VXR routers have six slots for port adapters, and one slot for an
input/output (I/O) controller. The slots are numbered from the lower left to the upper right, beginning
with slot 1 and continuing through slot 6. You can place the port adapters in any of the six slots (slot 1
through slot 6). Slot 0 is always reserved for the I/O controller. Figure 1-12 shows the slot numbering
on a Cisco 7206 router. The Cisco 7206VXR router is not shown.
Figure 1-12
Port Adapter Slots in the Cisco 7206 Router
3
2
1
0
6
TOKEN RING
5
FAST ETHERNET
4
5
RJ4
MII
0
LIN
K
D
LE
AB
EN
3
3
2
2
1
LINK
1
0
3
EN
AB
LE
0
D
ETHERNET 10BT
J-4
2
TX
RX
4
TX
RX
3
TX
RX
5
0
T
C
T
O
II
M N
E
SL
EJ
E
IA
C
M
PC
EN
AB
L
ED
0
R
Port adapter slot 5
Port adapter slot 3
Port adapter slot 1
5
J-4
R EN
5
R
R
PW
J-4 K
O K
LIN 1 O
28329
FE
M
II
T
O
SL
2
1
FAST ETHERNET INPUT/OUTPUT CONTROLLER
1
Cisco 7200
Series
TX
RX
TX
RX
1
0
7
6
5
4
3
2
1
0
EN
EN
ETHERNET-10BFL
SERIAL-V.35
Port adapter slot 6
Port adapter slot 4
Port adapter slot 2
Port adapter slot 0
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-8
OL-3474-07
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco uBR7200 Series Router Slot Numbering
The Cisco uBR7223 router has one port adapter slot (slot 1). Slot 0 is always reserved for the I/O
controller—if present. The Cisco uBR7223 router is not shown.
The Cisco uBR7246 router and Cisco uBR7246VXR router have two port adapter slots (slot1 and slot
2). Slot 0 is always reserved for the I/O controller—if present. Figure 1-13 shows the slot numbering of
port adapters on a Cisco uBR7246VXR router. The Cisco uBR7246 router is not shown.
Port Adapter Slots in the Cisco uBR7246VXR Router
5
uBR - MCI6
5
uBR - MCI6
5
uBR - MCI6
5
uBR - MCI6
S
S
D
4
Port adapter slot 2
U
S
3
U
S
U
2
U
S
D
1
U
U
LE
0
Port adapter slot 1
(blank)
S
S
D
U
S
2
U
S
D
1
U
U
LE
0
S
S
D
U
S
2
U
S
D
1
U
U
LE
0
H11323
S
D
S
2
U
S
1
U
S
U
D
LE
U
0
EN
AB
S
EN
AB
S
EN
AB
S
EN
AB
S
Port adapter slot 0
(I/O controller)
S
Figure 1-13
Cable modem card slot 3
Cable modem card slot 4
Cable modem card slot 5
Cable modem card slot 6
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-9
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco 7201 Router Slot Numbering
Figure 1-14 shows the front view of a Cisco 7201 router with a port adapter installed. There is only one
port adapter slot (slot 1) in a Cisco 7201 router.
Figure 1-14
Port Adapter Slot in the Cisco 7201 Router
Port adapter slot
D
R
LE LS RIE M
AB EL AR AR
EN RX C RX C X AL
R
ATM
PA
SLOT 1
Cisco 720
1
LINK/ACTV
SFP
CONSOLE
RJ45 EN
LINK/ACTV
TX SFP
RX
LINK/ACTV
SFP
LINK/ACTV
TX SFP
RX
GE 0/0
230308
RJ45 EN
MNGMNT
USE ONLY
GE 0/1
GE 0/2
ALARM
GE 0/3
AUX
FE 0/0
FE
LINK
PWR OK
0
COMPACT
FLASH
STATUS
CF
ACTV
Cisco 7301 Router Slot Numbering
Figure 1-15 shows the front view of a Cisco 7301 router with a port adapter installed. There is only one
port adapter slot (slot 1) in a Cisco 7301 router.
Figure 1-15
Port Adapter Slot in the Cisco 7301 Router
Port adapter slot
D
LE
AB
EN
S IER
LL R RM
CE CAR LA
RX RX RX A
ATM
GIGABIT ETHER
NET
RJ45 EN
CISCO 7400
0/0
LINK
TX GBIC
GIGABIT ETHER
NET
RX
RJ45 EN
0/1
LINK
TX GBIC
GIGABIT ETHER
NET
RX
RJ45 EN
0/2
LINK
TX GBIC
AUX
RX
CONSOLE
ALARM
SERIES
CISCO 7411
COMPACT
FLASH
100-24 0V,
2A, 50/60
Hz
24V=9 A,
48 - 60V=5
A
STATUS
84988
SLOT 1
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-10
OL-3474-07
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering
The Cisco 7304 PCI port adapter carrier card installs into Cisco 7304 router module slots 2 through 5.
Figure 1-16 shows the module slot numbering on a Cisco 7304 router. The port adapter slot number is
the same as the module slot number. Slot 0 and slot 1 are reserved for the NPE module or NSE module.
Figure 1-16
Module Slots on the Cisco 7304 Router
Slot 4
7300-2
OC3AT
M-MM
TX
OIR
0
Slot 5
RX
STATUS
2-PORT
TX
OC3 ATM
1
RX
MM
CARRIER
ALARM/
9K-10C
48
ACTIVE/
LOOPBAC
K
CARRIER
ALARM/
ACTIVE/
LOOPBAC
K
TX
OIR
RX
STATUS
1-PORT
OC48 POS
9K-40C
w/ SMS
3/POS
-MM
R
OIR
STATUS
4-POR
T OC3
0
1
POS w/
2
3
MM
CARRIER
ALARM/
70550
ACTIVE/
LOOPBA
CK
Slot 0
Slot 2
Slot 3
Slot 1
The Cisco 7304 PCI port adapter carrier card accepts one single-width port adapter. Figure 1-17 shows
a Cisco 7304 PCI port adapter carrier card with a port adapter installed.
Figure 1-17
-PA
EN
AB
LE
D
S IER
LL RR RM
CE CA LA
RX RX RX A
84653
73 00 -CC
Cisco 7304 PCI Port Adapter Carrier Card—Port Adapter Installed
OIR
STATUS
7300 PA
ATM
CARRIE
R
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-11
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco 7401ASR Router Slot Numbering
Figure 1-18 shows the front view of a Cisco 7401ASR router with a port adapter installed. There is only
one port adapter slot (slot 1) in a Cisco 7401ASR router.
Figure 1-18
D
R
LE LS RIE M
AB EL AR AR
EN RX C RX C X AL
TX
RX
ENHANCED
ATM
57680
R
Port Adapter Slot in the Cisco 7401ASR Router
Cisco 7500 Series Routers with VIP Slot Numbering
The PA-2FE is supported on theVIP2, VIP4, VIP6-80 versatile interface processors used in Cisco 7500
series routers. In the Cisco 7505 router, the VIP motherboard is installed horizontally in the VIP slot. In
the Cisco 7507 router and Cisco 7513 router, the VIP motherboard is installed vertically in the VIP slot.
The port adapter can be installed in either bay (port adapter slot 0 or 1) on the VIP. The bays are
numbered from left to right on the VIP. Figure 1-19 shows the slot numbering on a VIP.
Figure 1-19
VIP Slot Locations
1
129720
2
1
VIP port adapter slot 0
2
VIP port adapter slot 1
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-12
OL-3474-07
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco 7505 routers have four slots for port adapters, and one slot for a Route Switch Processor (RSP).
The slots are numbered from bottom to top. You can place the port adapters in any of the VIP interface
slots (slot 0 through 3). One slot is always reserved for the RSP. Figure 1-20 shows the slot numbering
on a Cisco 7505 router.
VIP Slots in the Cisco 7505 Router
T
E
OL
NS
CO
AU
X.
HA
SE
U
RE
CP
T
EC
2
EN
AB
EN
LE
AB
LE
EJ
S L S LO
OT T
0 1
AL
RM
NO
1
ROUTE SWITCH PROCESSOR
LT
Figure 1-20
3
4
122193
5
1
RSP
4
VIP interface—slot 1
2
VIP interface—slot 3
5
VIP interface—slot 0
3
VIP interface—slot 2
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-13
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco 7507 routers have five slots for port adapters, and two slots for RSPs. The slots are numbered from
left to right. You can place the port adapters in any of the VIP interface slots (slot 0, 1, 4, 5, or 6). Slots
2 and 3 are always reserved for RSPs. Figure 1-21 shows the slot numbering on a Cisco 7507 router.
Figure 1-21
AC
FA
IL
PO
WE
R
NO
EN
RM
AB
EJ
T
SL MA
AV ST
E ER
O
SL
AV
E/M
CP
RE
AC
EC
SL SLO
OT T
0 1
I
DC
LE
AL
AS
U
TE
HA
SE
R
LT
EN
AB
LE
T
FA
IL
PO
WE
R
AU
NS
OL
I
E
ROUTE SWITCH PROCESSOR 2
CO
X.
122194
DC
VIP Slots in the Cisco 7507 Router
O
1
2
3
4
5
6
7
1
VIP interface—slot 0
5
VIP interface—slot 4
2
VIP interface—slot 1
6
VIP interface—slot 5
3
RSP—slot 2
7
VIP interface—slot 6
4
RSP—slot 3
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-14
OL-3474-07
Chapter 1
Overview
Port Adapter Slot Locations on the Supported Platforms
Cisco 7513 routers have eleven slots for port adapters, and two slots for RSPs. The slots are numbered
from left to right. You can place the port adapters in any of the VIP interface slots (slots 0 through 5, or
slots 9 through 12). Slots 6 and 7 are always reserved for RSPs. Figure 1-22 shows the slot numbering
on a Cisco 7513 router.
Figure 1-22
VIP Slots in the Cisco 7513 Router
NO
RM
NO
AL
RM
AL
EN
EJE
SLO SLO
T0 T1
SLA MA
S
V E TE
R
SLA MA
S
VE TE
R
VE
SLA
/M
CP
RE
AU
/M
CP
RE
AU
X.
OLE
VE
R
LT
T
CO
NS
AS
U
TE
HA
SE
AB
LE
R
LT
EN
T
X.
OLE
ROUTE SWITCH PROCESSOR 2
FAN
OK
TE
HA
ROUTE SWITCH PROCESSOR 2
AC
OK
NS
AS
U
SE
LE
CT
SLO SLO
T0 T1
SLA
CO
EJE
CT
AB
OUTPUT
FAIL
AC
OK
FAN
OK
OUTPUT
FAIL
A
122195
POWER
POWER
B
I
I
0
0
1
3
2
5
4
7
6
9
8
11
10
13
12
1
VIP interface—slot 0
8
RSP—slot 7
2
VIP interface—slot 1
9
VIP interface—slot 8
3
VIP interface—slot 2
10 VIP interface—slot 9
4
VIP interface—slot 3
11 VIP interface—slot 10
5
VIP interface—slot 4
12 VIP interface—slot 11
6
VIP interface—slot 5
13 VIP interface—slot 12
7
RSP—slot 6
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-15
Chapter 1
Overview
Identifying Interface Addresses
Identifying Interface Addresses
The following sections describe the interface address formats for the PA-2FE in supported platforms.
Interface addresses specify the actual physical location of each interface on a router or switch.
Interfaces on a PA-2FE installed in a router maintain the same address regardless of whether other
port adapters are installed or removed. However, when you move a port adapter to a different slot, the
first number in the interface address changes to reflect the new port adapter slot number.
Interfaces on a PA-2FE installed in a VIP maintain the same address regardless of whether other interface
processors are installed or removed. However, when you move a VIP to a different slot, the interface
processor slot number changes to reflect the new interface processor slot.
Note
Interface ports are numbered from left to right starting with 0.
The following subsections describe the interface address formats for the supported platforms:
•
Cisco 7120 Router and Cisco 7140 Router Interface Addresses, page 1-17
•
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses, page 1-17
•
Cisco uBR7200 Series Routers Interface Addresses, page 1-18
•
Cisco 7201 Router Interface Addresses, page 1-18
•
Cisco 7301 Router Interface Addresses, page 1-18
•
Cisco 7304 PCI Port Adapter Carrier Card Interface Addresses, page 1-18
•
Cisco 7401ASR Router Interface Addresses, page 1-18
•
Cisco 7500 Series Routers VIP Interface Addresses, page 1-19
Table 1-4 summarizes the interface address formats for the supported platforms.
Table 1-4
Identifying Interface Addresses
Platform
Interface Address Format
Numbers
Syntax
Cisco 7120 series router
Port-adapter-slot-number/interface-port-number
Port adapter slot—always 3
3/0
Interface port—0 or 1
Cisco 7140 series routers
Port-adapter-slot-number/interface-port-number
Port adapter slot—always 4
4/0
Interface port—0 or 1
Cisco 7200 series routers and Port-adapter-slot-number/interface-port-number
Cisco 7200 VXR routers
(Cisco 7202, Cisco 7204,
Cisco 7204VXR,
Cisco 7206,
Cisco 7206VXR)
Port adapter slot—1 through 1/0
6 (depends on the number of
slots in the router)
Cisco uBR7200 series
routers (Cisco uBR7223)
Port-adapter-slot-number/interface-port-number
Port adapter slot—1
Cisco uBR7200 series
routers (Cisco uBR7246,
Cisco uBR7246VXR)
Port-adapter-slot-number/interface-port-number
Interface port—0 or 1
1/0
Interface port—0 or 1
Port adapter slot—1 and 2
1/0
Interface port—0 or 1
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-16
OL-3474-07
Chapter 1
Overview
Identifying Interface Addresses
Table 1-4
Identifying Interface Addresses (continued)
Platform
Interface Address Format
Numbers
Syntax
Cisco 7201 router
Port-adapter-slot-number/interface-port-number
Port adapter slot—always 1
1/0
Interface port—0 or 1
Cisco 7301 router
Port-adapter-slot-number/interface-port-number
Port adapter slot—always 1
1/0
Interface port—0 or 1
Cisco 7304 PCI port adapter
carrier card in Cisco 7304
router
Module-slot-number/interface-port-number
Cisco 7401ASR router
Port-adapter-slot-number/interface-port-number
Module slot— slot 2 through 3/0
5
Interface port—0 or 1
Port adapter slot—always 1
1/0
Interface port—0 or 1
VIP in Cisco 7500 series
routers
Interface-processor-slot-number/port-adapter-slotnumber/interface-port-number
Interface processor slot—0
through 12 (depends on the
number of slots in the
router)
3/1/0
Port adapter slot— 0 or 1
Interface port—0 or 1
Note
In Cisco 7200 series routers, Cisco 7200 VXR routers, and Cisco uBR7200 series routers, port adapter
slot 0 is reserved for the Fast Ethernet port on the I/O controller, if present.
Cisco 7120 Router and Cisco 7140 Router Interface Addresses
In the Cisco 7120 series router, port adapters are installed in port adapter slot 3. See Figure 1-10. In the
Cisco 7140 series router, port adapters are installed in port adapter slot 4. See Figure 1-11.
The interface address is composed of a two-part number in the format
port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed on a Cisco 7120 router, the interface addresses would be 3/0 and 3/1. If a dual-port PA-2FE is
installed on a Cisco 7140 router, the interface addresses would be 4/0 and 4/1.
Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses
In Cisco 7200 series routers and Cisco 7200 VXR routers, port adapter slots are numbered from the
lower left to the upper right, beginning with slot 1 and continuing through slot 2 for the Cisco 7202,
slot 4 for the Cisco 7204 and Cisco 7204VXR, and slot 6 for the Cisco 7206 and Cisco 7206VXR. Port
adapters can be installed in any available port adapter slot from 1 through 6 (depending on the number
of slots in the router). (Slot 0 is reserved for the I/O controller.) See Figure 1-12.
The interface address is composed of a two-part number in the format
port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed in slot 1of a Cisco 7200 series router, the interface addresses would be 1/0 and 1/1 (slot 1 and
ports 0 and 1). If the dual-port PA-2FE were installed in slot 4, the interface addresses would be 4/0 and
4/1 (slot 4 and ports 0 and 1)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-17
Chapter 1
Overview
Identifying Interface Addresses
Cisco uBR7200 Series Routers Interface Addresses
In the Cisco uBR7223 router, only one slot accepts port adapters and it is numbered slot 1.
In the Cisco uBR7246 router and Cisco uBR7246VXR router, port adapters can be installed in two port
adapter slots (slot1 and slot 2). Slot 0 is always reserved for the I/O controller—if present. See
Figure 1-13.
The interface address is composed of a two-part number in the format
port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed in slot 1of a Cisco uBR7223 series router, the interface addresses would be 1/0 and 1/1 (slot 1
and ports 0 and 1). If the dual-port port adapter were installed in slot 2 of a Cisco uBR7246 or
Cisco uBR7248VXR router, the interface addresses would be 2/0 and 2/1 (slot 2 and ports 0 and 1).
Cisco 7201 Router Interface Addresses
In the Cisco 7201 router, only one slot accepts port adapters and it is numbered slot 1. See Figure 1-14.
The interface address is composed of a two-part number in the format
port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed on a Cisco 7201 router, the interface addresses would be 1/0 and 1/1.
Cisco 7301 Router Interface Addresses
In the Cisco 7301 router, only one slot accepts port adapters and it is numbered slot 1. See Figure 1-15.
The interface address is composed of a two-part number in the format
port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed on a Cisco 7301 router, the interface addresses would be 1/0 and 1/1.
Cisco 7304 PCI Port Adapter Carrier Card Interface Addresses
In the Cisco 7304 router, port adapters are installed in a Cisco 7304 PCI port adapter carrier card, which
installs in Cisco 7304 router module slots 2 through 5. The port adapter slot number is the same as the
module slot number. See Figure 1-16.
The interface address is composed of a two-part number in the format
module-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed in the Cisco 7304 PCI port adapter carrier card in Cisco 7304 router module slot 3, the interface
addresses would be 3/0 and 3/2.
Cisco 7401ASR Router Interface Addresses
In the Cisco 7401ASR router, only one slot accepts port adapters and it is numbered slot 1. See
Figure 1-18.
The interface address is composed of a two-part number in the format
port-adapter-slot-number/interface-port-number. See Table 1-4. For example, if a dual-port PA-2FE is
installed on a Cisco 7401ASR router, the interface addresses would be 1/0 and 1/1.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-18
OL-3474-07
Chapter 1
Overview
Identifying Interface Addresses
Cisco 7500 Series Routers VIP Interface Addresses
In Cisco 7500 series routers, port adapters are installed on a versatile interface processor (VIP), which
installs in interface processor slots 0 through 12 (depending on the number of slots in the router). The
port adapter can be installed in either bay (port adapter slot 0 or 1) on the VIP. See Figure 1-19,
Figure 1-20, Figure 1-21, and Figure 1-22.
The interface address for the VIP is composed of a three-part number in the format
interface-processor-slot-number/port-adapter-slot-number/interface-port-number. See Table 1-4.
The first number identifies the slot in which the VIP is installed (slot 0 through 12, depending on the
number of slots in the router).
The second number identifies the bay (port adapter slot) on the VIP in which the port adapter is installed
(0 or 1). The bays are numbered from left to right on the VIP.
The third number identifies the physical port number (interface port number) on the port adapter. The
port numbers always begin at 0 and are numbered from left to right. The PA-2FE is a dual-port port
adapter, therefore the port can be 0 or 1.
For example, if a dual-port PA-2FE is installed in a VIP in interface processor slot 3, port adapter slot 1,
the interface addresses would be 3/1/0 and 3/1/1.
Note
Although the processor slots in the seven-slot Cisco 7507 and the thirteen-slot Cisco 7513 chassis are
vertically oriented and those in the five-slot Cisco 7505 are horizontally oriented, all Cisco 7500 series
routers use the same method for slot and port numbering.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
1-19
Chapter 1
Overview
Identifying Interface Addresses
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
1-20
OL-3474-07
C H A P T E R
2
Preparing for Installation
This chapter describes the general equipment, safety, and site preparation requirements for installing the
PA-2FE. This chapter contains the following sections:
•
Required Tools and Equipment, page 2-1
•
Software and Hardware Requirements, page 2-2
•
Checking Hardware and Software Compatibility, page 2-2
•
Safety Guidelines, page 2-3
•
FCC Class A Compliance, page 2-10
Required Tools and Equipment
You need the following tools and parts to install a PA-2FE. If you need additional equipment, contact a
service representative for ordering information.
•
PA-2FE-TX or PA-2FE-FX
•
VIP (for installation in Cisco 7500 series chassis only)
•
Cisco 7304 PCI port adapter carrier card (for installation in Cisco 7304 router only)
•
Cables appropriate for the PA-2FE interfaces (RJ-45 and multimode optical-fiber cables are not
available from Cisco; they are available from commercial vendors.)
•
Number 1 Phillips and a 3/16-inch flat-blade screwdriver (for VIP installation only)
•
Number 2 Phillips screwdriver
•
Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist
strap included with all upgrade kits, field-replaceable units (FRUs), and spares
•
Antistatic mat
•
Antistatic container
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
2-1
Chapter 2
Preparing for Installation
Software and Hardware Requirements
Software and Hardware Requirements
Table 2-1 lists the recommended minimum Cisco IOS software release required to use the PA-2FE in
supported router or switch platforms.
Table 2-1
PA-2FE Software Requirements
Platform
Recommended Minimum Cisco IOS Release
Cisco 7120 series and Cisco 7140 series
routers
Cisco IOS Release 12.1(8)E or a later release of Cisco IOS Release 12.1E
Cisco 7200 series routers and Cisco 7200
VXR routers1
Cisco IOS Release 12.2(3) or a later release of Cisco IOS Release 12.2(3)
Cisco IOS Release 12.1(5)E or a later release of Cisco IOS Release 12.1E
Cisco IOS Release 12.2(4)B or a later release of Cisco IOS Release 12.2B
Cisco uBR7200 series routers
Cisco IOS Release 12.2(4)XF1 or a later release of Cisco IOS Release 12.2XF
Cisco 7201 router
Cisco IOS Release 12.4(4)XD7 or a later release of Cisco IOS Release 12.4XD
Cisco IOS Release 12.2(31)SB5 or a later release of Cisco IOS Release 12.2SB.
Cisco 7301 router
Cisco IOS Release 12.2(11)YZ or a later release of Cisco IOS Release 12.2YZ
Cisco 7304 PCI port adapter carrier card in PA-2FE-FX
Cisco 7304 router
Cisco IOS Release 12.2(14)SZ or a later release of Cisco IOS Release 12.2SZ
PA-2FE-TX
Cisco IOS Release 12.2(11)YZ or a later release of Cisco IOS Release 12.2YZ
Cisco 7401ASR router
Cisco IOS Release 12.2(1)DX or a later release of Cisco IOS Release 12.2DX
Cisco IOS Release 12.2(4)B or a later release of Cisco IOS Release 12. B
VIP in the Cisco 7500 series routers2, 3, 4, 5
Cisco IOS Release 12.2(3) or a later release of Cisco IOS Release 12.2(3)
Cisco IOS Release 12.1(5)E or a later release of Cisco IOS Release 12.1E
1. The PA-2FE can be used in all Cisco 7200 series routers using an NPE-175, NPE-200, NPE-225, NPE-300, NPE-400, or NSE-1.
2. The PA-2FE can be used in the VIP2, VIP4, and VIP6-80 in all Cisco 7500 series routers using a Route Switch Processor (RSP).
3. The specific VIP2 models recommended for the PA-2FE in all Cisco 7500 series router, are VIP2-40(=), which has 2 MB of SRAM and 32 MB of DRAM,
and VIP2-50(=), which has 4 to 8 MB of SRAM and 32 to 128 MB of SDRAM; however, the PA-2FE is also supported by the VIP2-15(=) and VIP2-20(=),
but we do not recommend its use with these VIP2 models.
4. The VIP2-40(=), VIP2-20(=), and VIP2-15(=) are limited to one PA-2FE per card.
5. VIP2-50 manufactured prior to May 1998 (version 2.2 and below) are incompatible with the PA-2FE.
Checking Hardware and Software Compatibility
To check the minimum software requirements of Cisco IOS software with the hardware installed on your
router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether
modules within a system are compatible, but it does provide the minimum IOS requirements for
individual hardware modules or components.
Note
Access to this tool is limited to users with Cisco.com login accounts.
To access Software Advisor, click Log In at Cisco.com and go to Support > Tools and Resources. You
can also access the tool by pointing your browser directly to
http://www.cisco.com/en/US/support/tsd_most_requested_tools.html.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
2-2
OL-3474-07
Chapter 2
Preparing for Installation
Safety Guidelines
Choose a product family or enter a specific product number to search for the minimum supported
software release needed for your hardware.
Safety Guidelines
This section provides safety guidelines that you should follow when working with any equipment that
connects to electrical power or telephone wiring.
Safety Warnings
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might
harm you. A warning symbol precedes each warning statement.
Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
2-3
Chapter 2
Preparing for Installation
Safety Guidelines
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
2-4
OL-3474-07
Chapter 2
Preparing for Installation
Safety Guidelines
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
2-5
Chapter 2
Preparing for Installation
Safety Guidelines
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
2-6
OL-3474-07
Chapter 2
Preparing for Installation
Safety Guidelines
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
2-7
Chapter 2
Preparing for Installation
Safety Guidelines
Electrical Equipment Guidelines
Follow these basic guidelines when working with any electrical equipment:
•
Before beginning any procedures requiring access to the chassis interior, locate the emergency
power-off switch for the room in which you are working.
•
Disconnect all power and external cables before moving a chassis
•
Do not work alone when potentially hazardous conditions exist.
•
Never assume that power has been disconnected from a circuit; always check.
•
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe;
carefully examine your work area for possible hazards such as moist floors, ungrounded power
extension cables, and missing safety grounds.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
2-8
OL-3474-07
Chapter 2
Preparing for Installation
Safety Guidelines
Telephone Wiring Guidelines
Use the following guidelines when working with any equipment that is connected to telephone wiring or
to other network cabling:
•
Never install telephone wiring during a lightning storm.
•
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
•
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
•
Use caution when installing or modifying telephone lines.
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are
improperly handled, results in complete or intermittent failures. Port adapters and processor modules
comprise printed circuit boards that are fixed in metal carriers. Electromagnetic interference (EMI)
shielding and connectors are integral components of the carrier. Although the metal carrier helps to
protect the board from ESD, use a preventive antistatic strap during handling.
Following are guidelines for preventing ESD damage:
Caution
•
Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.
•
Connect the equipment end of the strap to an unfinished chassis surface.
•
When installing a component, use any available ejector levers or captive installation screws to
properly seat the bus connectors in the backplane or midplane. These devices prevent accidental
removal, provide proper grounding for the system, and help to ensure that bus connectors are
properly seated.
•
When removing a component, use any available ejector levers or captive installation screws to
release the bus connectors from the backplane or midplane.
•
Handle carriers by available handles or edges only; avoid touching the printed circuit boards or
connectors.
•
Place a removed board component-side-up on an antistatic surface or in a static shielding container.
If you plan to return the component to the factory, immediately place it in a static shielding
container.
•
Avoid contact between the printed circuit boards and clothing. The wrist strap only protects
components from ESD voltages on the body; ESD voltages on clothing can still cause damage.
•
Never attempt to remove the printed circuit board from the metal carrier.
For safety, periodically check the resistance value of the antistatic strap. The measurement should be
between 1 and 10 megohms (Mohms).
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
2-9
Chapter 2
Preparing for Installation
FCC Class A Compliance
FCC Class A Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case users will be
required to correct the interference at their own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference
stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment
causes interference to radio or television reception, try to correct the interference by using one or more
of the following measures:
Note
•
Turn the television or radio antenna until the interference stops.
•
Move the equipment to one side or the other of the television or radio.
•
Move the equipment farther away from the television or radio.
•
Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is,
make certain the equipment and the television or radio are on circuits controlled by different circuit
breakers or fuses.)
The PA-2FE port adapter has been designed to meet these requirements. Modifications to this product
that are not authorized by Cisco Systems, Inc. could void the various approvals and negate your authority
to operate the product.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
2-10
OL-3474-07
C H A P T E R
3
Removing and Installing Port Adapters
This chapter describes how to remove the PA-2FE port adapter from supported platforms and also how
to install a new or replacement port adapter. This chapter contains the following sections:
•
Handling Port Adapters, page 3-1
•
Online Insertion and Removal, page 3-2
•
Warnings and Cautions, page 3-3
•
Port Adapter Removal and Installation, page 3-4
•
Connecting a PA-2FE RJ-45 or SC Cable, page 3-16
Handling Port Adapters
Each port adapter circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge
(ESD) damage.
Note
When a port adapter slot is not in use, a blank port adapter must fill the empty slot to allow the router or
switch to conform to electromagnetic interference (EMI) emissions requirements and to allow proper
airflow across the port adapters. If you plan to install a new port adapter in a slot that is not in use, you
must first remove the blank port adapter.
Caution
When powering off the router, wait a minimum of 30 seconds before powering it on again.
Caution
Always handle the port adapter by the carrier edges and handle; never touch the port adapter components
or connector pins. (See Figure 3-1.)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-1
Chapter 3
Removing and Installing Port Adapters
Online Insertion and Removal
Figure 3-1
Handling a Port Adapter
Metal carrier
H6420
Printed circuit board
Online Insertion and Removal
Several platforms support online insertion and removal (OIR) of port adapters; therefore, you do not
have to power down routers when removing and replacing a PA-2FE in the Cisco 7100 series routers,
Cisco 7200 series routers, Cisco 7200 VXR routers, Cisco uBR7200 series routers, Cisco 7201 router,
Cisco 7301 router, or Cisco 7401ASR router.
Although the Cisco 7304 PCI port adapter carrier card and VIP support OIR, individual port adapters do
not. To replace port adapters in the Cisco 7304 router or Cisco 7500 series routers, you must first remove
the Cisco 7304 PCI port adapter carrier card or VIP from the router and then install or replace
port adapters as required. If a blank port adapter is installed in the Cisco 7304 PCI port adapter carrier
card or VIP on which you want to install a new port adapter, you must first remove the Cisco 7304 PCI
port adapter carrier card or VIP from the router and then remove the blank port adapter.
Caution
To prevent system problems, do not remove port adapters from the Cisco 7304 PCI port adapter carrier
card or Cisco 7500 VIP motherboard or attempt to install other port adapters when the system is
operating.
OIR allows you to install and replace port adapters and service adapters (carrier cards and VIPs) while
the router is operating; you do not need to notify the software or shut down the system power, although
you should not run traffic through the port adapter you are removing while it is being removed. OIR is
a method that is seamless to end users on the network, maintains all routing information, and preserves
sessions.
It is wise to gracefully shut down the system before removing a port adapter that has active traffic moving
through it. Removing a port adapter while traffic is flowing through the ports can cause system
disruption. Once the port adapter is inserted, the ports can be brought back up.
Note
As you disengage the port adapter from the router or switch, OIR administratively shuts down all active
interfaces in the port adapter.
The following is a functional description of OIR for background information only; for specific
procedures for installing and replacing a PA-2FE in a supported platform, refer to the “Port Adapter
Removal and Installation” section on page 3-4.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-2
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Warnings and Cautions
Each PA-2FE has a bus connector that connects it to the router. The connector has a set of tiered pins in
three lengths that send specific signals to the system as they make contact with the port adapter. The
system assesses the signals it receives and the order in which it receives them to determine if a port
adapter is being removed from or introduced to the system. From these signals, the system determines
whether to reinitialize a new interface or to shut down a disconnected interface.
Specifically, when you insert a port adapter, the longest pins make contact with the port adapter first, and
the shortest pins make contact last. The system recognizes the signals and the sequence in which it
receives them.
When you remove or insert a port adapter, the pins send signals to notify the system of changes. The
router then performs the following procedure:
Note
1.
Rapidly scans the system for configuration changes.
2.
Initializes newly inserted port adapters or administratively shuts down any vacant interfaces.
3.
Brings all previously configured interfaces on the port adapter back to their previously installed
state. Any newly inserted interface is put in the administratively shutdown state, as if it was present
(but not configured) at boot time. If a similar port adapter type is reinserted into a slot, its ports are
configured and brought online up to the port count of the originally installed port adapter of that
type.
Before you begin installation, read Chapter 2, “Preparing for Installation,” for a list of parts and tools
required for installation.
Warnings and Cautions
Observe the following warnings and cautions when installing or removing port adapters.
Caution
Do not slide a port adapter all the way into the slot until you have connected all required cables. Trying
to do so disrupts normal operation of the router or switch.
Caution
To prevent jamming the carrier between the upper and the lower edges of the port adapter slot, and to
ensure that the edge connector at the rear of the port adapter mates with the connection at the rear of the
port adapter slot, make certain that the carrier is positioned correctly, as shown in the cutaway
illustrations in the “Port Adapter Removal and Installation” section on page 3-4.
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the midplane with your hand or any metal tool, or you could shock yourself. Statement 181
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-3
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Port Adapter Removal and Installation
In this section, the illustrations that follow give step-by-step instructions on how to remove and install
port adapters. This section contains the following illustrations:
Tip
•
Cisco 7100 Series—Removing and Installing a Port Adapter, page 3-5
•
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and Installing a Port Adapter,
page 3-6
•
Cisco uBR7200 Series Routers—Removing a Port Adapter, page 3-7
•
Cisco uBR7200 Series Routers—Installing a Port Adapter, page 3-8
•
Cisco 7201 Router—Removing and Installing a Port Adapter, page 3-9
•
Cisco 7301 Router—Removing and Installing a Port Adapter, page 3-10
•
Cisco 7304 PCI Port Adapter Carrier Card—Removing and Installing a Port Adapter, page 3-11
•
Cisco 7401ASR Router—Removing and Installing a Port Adapter, page 3-13
•
Cisco 7500 Series Router VIP—Removing and Installing a Port Adapter, page 3-13
If a port adapter lever or other retaining mechanism does not move to the locked position, the port
adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot,
reinsert it, and move the port adapter lever or other mechanism to the locked position.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-4
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco 7100 Series—Removing and Installing a Port Adapter
Step 1
To remove the port adapter, use a number 2 Phillips screwdriver
to loosen the screws on the locking tab. Then slide the tab down
to the unlocked position.
Locked
Unlocked
ESD plug
Slot 3
SLOT 0
SLOT 1
PWR
ACT ACT
0
5
FE 0 / 0
I
E3
EN
TX
FE
0/1
LNK LNK
0
1
CONS
AUX
SYS
RDY
RX
RX
2
CEL CAR ALM
7120 - AE3
Step 2
Grasp the handle of the port adapter and pull the port adapter
from the router, about halfway out of its slot. If you are removing
a blank port adapter, pull the blank port adapter completely out
of the chassis slot.
Step 3
With the port adapter halfway out of the slot, disconnect all
cables from the port adapter.
Step 4
After disconnecting the cables, pull the port adapter from its
chassis slot.
Step 5
To insert the port adapter, carefully align the port adapter carrier
between the upper and the lower edges of the port adapter slot.
Guides
5
Step 6
With the port adapter halfway into the slot,
connect all required cables to the port adapter.
I
RCVR
EN
XMTR
RCLK FERF RL
FE 0 /
AIS OOF LL
Step 7
After connecting all required cables, carefully slide the port
adapter all the way into the slot until the port adapter is seated in
the router midplane.
After the port adapter is properly seated, lock the port adapter
retaining mechanism.
26522
Step 8
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-5
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and
Installing a Port Adapter
Step 1
Port adapter lever
(locked position)
To remove the port adapter, place
the port adapter lever in the
unlocked position. (See A.) The
port adapter lever remains in the
unlocked position.
Step 2
3
2
1
0
6
TOKEN RING
5
4
NK
LI
0
EN
RJ
AB
LE
D
K
3
3
2
LIN
1
0
2
D
1
0
LE
AB
3
EN
45
FAST ETHERNET
ETHERNET 10BT
A
MII
Grasp the handle of the port adapter
and pull the port adapter from the
router, about halfway out of its slot.
If you are removing a blank port
adapter, pull the blank port adapter
completely out of the chassis slot.
2
CD
LB
RC
RD
TC
TD
CD
LB
RC
RD
TC
TD
CD
LB
RC
RD
TC
TD
CD
LB
RC
RD
TC
TD
EN
FAST SERIAL
1
FAST ETHERNET INPUT/OUTPUT CONTROLLER
RE
U
With the port adapter halfway out of
the slot, disconnect all cables from
the port adapter. After disconnecting
the cables, pull the port adapter
from its chassis slot.
PW
K R
O
1O
R
LI J4
N 5
K
M
EN II
0
SLO
T
T
EJE
C
IA
C
M
PC
Note: This adapter
removal applies to any
port or service adapter.
Step 3
R
EN J4
5
EN
AB
LE
D
0
CP
FE
RJ
-4
5
M
II
SLO
T
1
SE
T
Cisco 7200
Series
Port adapter lever
(unlocked position)
Step 4
To insert the port adapter, carefully
align the port adapter carrier
between the upper and the lower
edges of the port adapter slot.
(See B.)
2
6
4
45
RJ
LI
2
0
MII
EN
AB
LE
D
K
LIN
3
2
2
3
1
0
D
1
0
LE
AB
3
EN
NK
FAST ETHERNET
ETHERNET 10BT
Carefully slide the new port adapter
halfway into the port adapter slot.
(See B.)
SE
RE
CP
5
-4
RJ
U
M
FE
FAST ETHERNET INPUT/OUTPUT CONTROLLER
27996
PW
O
K R
1O
R
LI J4
N 5
K
5
R
EN J4
T
SLO
M
EN II
0
T
C
EJE
PC
M
C
IA
EN
AB
LE
D
SLO
T
II
1
T
1
Cisco 7200
Series
B
Step 6
1
0
5
Step 5
3
TOKEN RING
Slot
guide
With the port adapter halfway into
the slot, connect all required cables
to the port adapter. After connecting
all required cables, carefully slide
the port adapter all the way into the
slot until the port adapter is seated
in the router midplane.
Step 7
After the port adapter is properly
seated, lock the port adapter lever.
(See A.)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-6
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco uBR7200 Series Routers—Removing a Port Adapter
Step 1
To remove the port adapter,
unlock the port adapter
retaining mechanism. The port
adapter lever remains in the
unlocked position.
Port adapters
Port adapter lever
(locked position)
A
Place the port adapter lever
(Cisco uBR7223, see A), or
the port adapter retention clip
(Cisco uBR7246 and Cisco
uBR7246 VXR, see B) in the
unlocked position. Either
mechanism remains in the
unlocked position.
Note: This adapter
removal applies to any
port or service adapter.
Port adapter lever
(unlocked position)
Port adapter
retention clip
(locked position)
Step 2
Grasp the handle of the port
adapter and pull the port
adapter from the router, about
halfway out of its slot.
If you are removing a blank
port adapter, pull the blank
port adapter completely out of
the chassis slot.
Port adapters
With the port adapter halfway
out of the slot, disconnect all
cables from the port adapter.
After disconnecting the cables,
pull the port adapter from its
chassis slot.
26523
Step 3
Port adapter
retention clip
(unlocked position)
B
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-7
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco uBR7200 Series Routers—Installing a Port Adapter
Step 1
To insert the port adapter, carefully
align the port adapter carrier
between the upper and the lower
edges of the port adapter slot.
Metal carrier
PC board
26524
Inside
slot guide
Step 2
Carefully slide the new port adapter
halfway into the port adapter slot.
Step 3
With the port adapter halfway into
the slot, connect all required cables
to the port adapter. After connecting
all required cables, carefully slide
the port adapter all the way into the
slot until the port adapter is seated in
the router midplane.
Step 4
After the port adapter is properly
seated, lock the port adapter lever or
retention clip, depending on your
system. (See illustration on
preceding page.)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-8
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco 7201 Router—Removing and Installing a Port Adapter
Step 1
Use an ESD wrist strap to ground yourself to the router.
Step 2
To remove the port adapter, place the port adapter lever in the unlocked position. The port adapter lever
remains in the unlocked position.
Step 3
Grasp the handle of the port adapter and pull the port adapter about halfway out of its slot. If you are
removing a blank port adapter, pull the blank port adapter completely out of the chassis slot.
Step 4
With the port adapter halfway out of the slot, disconnect all cables from the port adapter.
After disconnecting the cables, pull the port adapter from the chassis slot.
Caution
The port adapter must slide into the slot guides close to the chassis lid. Do not allow the port adapter
components to come in contact with the system board or the port adapter could be damaged.
GIGABIT ETHERN
ET 0/0
RJ45 EN
LINK
TX GBIC
Cisco 7201RX
R
RJ45 EN
LINK/ACTV
SFP
ATM
GIGABIT ETHERN
ET 0/1
RJ45 EN
LINK
TX GBIC
RJ45 EN
TX
CISCO 7301
GE
GIGABIT ETHERN
ET 0/2
RX
LINK/ACTV
SFP
RX
RJ45 EN
LINK
TX GBIC
LINK/ACTV
SFP
TX
RX
AUX
CONSOLE
LINK/ACTV
SFP RX
CONSOLE
100-240 V,
2A, 50/60
Hz
24V=9A ,
48 - 60V=5A
ALARM
MNGMNT
0/0
GE 0/1
USE ONLYCOMPACT
FLASH
STATUS
GE 0/2
ALARM
GE 0/3
AUX
FE 0/0
FE
LINK
PWR OK
0
COMPACT
FLASH
STATUS
CF
ACTV
170902
SLOT 1
D
R
LE S RIE M
AB ELL AR R
EN RX C RX C X ALA
Step 5
To insert the port adapter, carefully align the port adapter carrier in the slot guides. Slide the new port
adapter halfway into the chassis.
Step 6
Connect all the required cables to the port adapter. After connecting all required cables, carefully slide the
port adapter all the way into the slot until the port adapter is seated in the midplane.
Step 7
After the port adapter is properly seated, lock the port adapter lever.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-9
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco 7301 Router—Removing and Installing a Port Adapter
Step 1
Use an ESD wrist strap to ground yourself to the router.
Step 2
To remove a port adapter, use a Phillips screwdriver to turn the screw holding the port adapter latch. The screw
should be loose enough to allow the latch to rotate to an unlocked position. (See A.) The latch can rotate 360˚.
Step 3
Grasp the handle and pull the port adapter from the router, about halfway out of its slot. (See B.) If you are
removing a blank port adapter, pull the blank port adapter completely out of the chassis slot.
Step 4
With the port adapter halfway out of the slot, diconnect all cables from the port adapter. After disconnecting
the cables, pull the port adapter from its chassis slot.
Caution
The port adapter must slide into the slot guides close to the chassis lid. (See C.) Do not allow the port
adapter components to come in contact with the system board or the port adapter could be damaged.
GIGABIT ETHERNE
T 0/0
RJ45 EN
R
ATM
GIGABIT ETHERNE
T 0/1
RX
RJ45 EN
LINK
TX GBIC
GIGABIT ETHERNE
T 0/2
RX
RJ45 EN
LINK
TX GBIC
AUX
CONSOLE
RX
ALARM
COMPACT
FLASH
100-240V
, 2A, 50/60
Hz
24V=9A ,
48 - 60V=5A
STATUS
A
B
CISCO 7411
LINK
TX GBIC
A
84129
SLOT 1
D
R
LE LS RIE M
AB EL AR AR
EN RX C RX C X AL
B
C
Step 5
To insert the port adapter, carefully align the port adapter carrier in the slot guides. (See C.) Slide the new
port adapter halfway into the chassis.
Step 6
Connect all required cables to the port adapter. After connecting all required cables, carefully slide the port
adapter all the way into the slot until the port adapter is seated in the midplane.
Step 7
After the port adapter is properly seated, turn and secure the port adapter latch in the upright, locked
position. (See A.) Tighten the screw to ensure the port adapter remains firmly in place.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-10
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco 7304 PCI Port Adapter Carrier Card—Removing and Installing a Port
Adapter
You can install one single-width port adapter in a Cisco 7304 PCI port adapter carrier card. This section
provides step-by-step instructions for removing and installing a port adapter in a Cisco 7304 PCI port
adapter carrier card.
Caution
Note
When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the
Cisco 7304 PCI port adapter carrier card.
If the Cisco 7304 PCI port adapter carrier card is still in the router, you must remove the port adapter
carrier card before removing a port adapter.
To remove and install a port adapter in a Cisco 7304 PCI port adapter carrier card, refer to Figure 3-2
and do the following:
Step 1
To remove the port adapter from the Cisco 7304 PCI port adapter carrier card, turn the port adapter lock
from its locked and horizontal position shown in A of Figure 3-2 to its unlocked and vertical position
shown in B of Figure 3-2.
Step 2
Ensure that the cables are disconnected from the port adapter before removing the Cisco 7304 PCI port
adapter carrier card from the chassis.
Step 3
Grasp the handle of the port adapter and pull the port adapter from the Cisco 7304 PCI port adapter
carrier card.
Step 4
To insert the port adapter in the Cisco 7304 PCI port adapter carrier card, locate the guide rails inside
the Cisco 7304 PCI port adapter carrier card that hold the port adapter in place. They are at the top left
and top right of the port adapter slot and are recessed about an inch, as shown in C of Figure 3-2.
Step 5
Carefully slide the port adapter in the Cisco 7304 PCI port adapter carrier card until the port adapter
makes contact with the port adapter interface connector. When fully seated, the port adapter front panel
should be flush with the face of the Cisco 7304 PCI port adapter carrier card.
Step 6
After the port adapter is properly seated, turn the port adapter lock to its locked and horizontal position,
as shown in A of Figure 3-2.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-11
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Figure 3-2 illustrates how to remove and install a port adapter in a Cisco 7304 PCI port adapter carrier
card.
Figure 3-2
Cisco 7304 PCI Port Adapter Carrier Card—Port Adapter Removal and Installation
A
73 00 -CC
B
-PA
EN
AB
LE
D
S IER
LL RR RM
CE CA LA
RX RX RX A
OIR
STATUS
7300 PA
ATM
CARRIE
R
C
C -P A
7300-C
C-PA
OIR
STATUS
7300 PA
A
EN
BL
CARRIER
ED L S R I E R M
L R R
CE A A
84657
7 3 0 0 -C
C L
RX RX RX A
ATM
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-12
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Cisco 7401ASR Router—Removing and Installing a Port Adapter
Step 1
To remove the port adapter, use a number 2 Phillips screwdriver to loosen the screw on the port adapter
latch. Rotate the port adapter latch until it clears the faceplate of the port adapter. (See A.) The latch can
rotate 360˚.
Unlocked
Locked
D
R
LE S RIE M
AB ELL AR R
EN RX C RX C X ALA
A
R
TX
RX
ENHANCED
ATM
Step 2
Pull the port adapter from the router, about halfway out of its slot. (If you remove a blank port adapter, keep
the blank port adapter for use in the router if you should ever remove the port adapter. The port adapter slot
must always be filled.)
Step 3
With the port adapter halfway out of the slot, disconnect all cables from the port adapter. After
disconnecting the cables, pull the port adapter completely out of the chassis slot.
Step 4
To insert the port adapter, locate the port adapter slot guides inside the Cisco 7401ASR router. They are
near the top, and are recessed about 1/2 inch. (See B.)
Caution
The port adapter must slide into the slot guides under the chassis lid. Do not allow the port adapter
components to come in contact with the system board, or the port adapter could be damaged.
B
AB
LE
D
R
LS RIE M
CEL CAR AR
RX RX RX AL
TX
RX
ENHANCED
ATM
57643
EN
Step 5
Insert the port adapter in the slot guides halfway, and then reconnect the port adapter cables.
Step 6
After the cables are connected, carefully slide the port adapter all the way into the slot until the port adapter
is seated in the router midplane. When installed, the port adapter input/output panel should be flush with the
face of the router.
Step 7
After the port adapter is properly seated, rotate the port adapter latch to the upright locked position and use
a number 2 Phillips screwdriver to tighten the latch screw. If needed, loosen the latch screw to rotate the
latch over the port adapter. Finish the installation by tightening the latch screw.
Cisco 7500 Series Router VIP—Removing and Installing a Port Adapter
You must remove the versatile interface processor (VIP) from the chassis before removing the port
adapter from the VIP or installing the port adapter in the VIP.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-13
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Removing and Installing a VIP Carrier Card in the Cisco 7500 Series Router
Card carrier guide
Remove a module as follows:
1. Use a screwdriver to loosen the captive
installation screws (shown in A and D).
A
2. Simultaneously pull the ejector levers out
to release the module from the backplane
connector (shown in B). The levers should
snap into their spring retainers.
3. Grasp the module handle with one hand
and place your other hand under the carrier
to support and guide the module as you pull it
out of the slot. Avoid touching the card.
4. Place the removed module on an antistatic
mat or antistatic foam, or immediately install
it in another slot.
Captive
installation
screw
B
5. Install a new module or a filler (MAS7KBLANK) to keep dust out of the chassis and
to maintain proper airflow through the
chassis.
Install a module as follows:
1. Choose a slot for the new module and
ensure that there is enough clearance to
accommodate any interface equipment that
you will connect directly to its ports.
C
2. Use a screwdriver to loosen the captive
installation screws (shown in A) and remove
the filler (or the existing module) from the slot
to be filled.
3. Hold the module handle with one hand,
and place your other hand under the carrier
to support the module and guide it into the
slot. Avoid touching the card.
D
Captive
installation
screw
ROUTE SWITCH PROCESSOR
T
HA
NS
CO
AU
X.
OL
E
SE
U
RE
CT
EJE
SL SLO
OT T
0 1
AL
RM
NO
6. Use the thumb and forefinger of each hand
to push the ejector lever flat against the
module (shown in B).
LT
5. Carefully slide the module into the slot until
the faceplate makes contact with the ejector
levers (shown in C).
CP
4. Place the back of the module in the slot
and align the guide on the carrier with the
groove in the slot (shown in A).
NK
RX
TX
LI
AS
LA S
SE 1
PR RP LA
OD RO SE
UI DUR
PR
T
OD LA SEKT OD
DE UC
UC
R R T
TO
DE KL
LA
CL AS
SE
AS SE
R
SE 1
DE
1
CL
AS
SE
1
39395
PR
CL
AB
EN
7. Use a screwdriver to tighten the captive
installation screws.
LE
D
ENHANCED GIGABIT ETHERNET
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-14
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Port Adapter Removal and Installation
Removing and Installing the Port Adapter in the VIP Carrier Card
Note: You must first remove the VIP
from the chassis before removing a port
adapter from the VIP.
Step 1
To remove the port adapter, remove
the screw that secures the port
adapter (or blank port adapter).
(See A.)
A
Step 2
Screw
With the screw removed, grasp the
handle on the front of the port adapter
(or blank port adapter) and carefully pull
it out of its slot, away from the edge
connector at the rear of the slot. (See A.)
Step 3
To insert the port adapter, carefully align
the port adapter carrier between the
upper and the lower edges of the port
adapter slot. (See B.)
B
Step 4
Carrier
Carefully slide the new port adapter into
the port adapter slot until the connector
on the port adapter is completely seated
in the connector at the rear of the port
adapter slot. (See B.)
T
NS
26520
CO
AU
X.
OL
E
SE
U
HA
LT
ROUTE SWITCH PROCESSOR
RE
CP
EJE
CT
C
S L S LO
OT T
0 1
AL
Step 6
Carefully slide the VIP motherboard into
the interface processor slot until the
connectors at the rear of the VIP are
completely seated in the connectors at
the rear of the interface processor slot.
Use the ejector levers to seat the VIP in
the interface processor slot. Tighten the
captive installation screws on the VIP.
(See C.)
Captive
installation
screw
RM
Install the screw in the rear of the port
adapter slot on the VIP. Do not
overtighten the screw. (See A.)
NO
Step 5
Upper edge
Lower edge
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-15
Chapter 3
Removing and Installing Port Adapters
Connecting a PA-2FE RJ-45 or SC Cable
Connecting a PA-2FE RJ-45 or SC Cable
To continue your PA-2FE port adapter installation, you must install the port adapter’s interface cables.
The following instructions apply to all supported platforms.
RJ-45 and SC-type fiber-optic cables are not available from Cisco; they are available from commercial
cable vendors.
Use the following procedure to connect RJ-45 or SC cables:
Step 1
If you have RJ-45 connections (PA-2FE-TX), attach the Category 5 unshielded twisted-pair (UTP) cable
directly to an RJ-45 port on the PA-2FE-TX. (See Figure 3-3.) The PA-2FE is an end-station device and
not a repeater. You must connect the PA-2FE to a transceiver, switch, hub, repeater, DTE, or
back-to-back to another 10/100-Mbps Fast Ethernet adapter.
If you have SC connections (PA-2FE-FX), attach the cable directly to an SC port on the PA-2FE-FX.
(See Figure 3-4.) Use either one duplex SC connector or two simplex SC connectors, and observe the
correct relationship between the receive (RX) and transmit (TX) ports on the PA-2FE-FX and your
repeater.
Note
Caution
Step 2
Port adapters have a handle attached, but this handle is not shown to allow a full detailed view
of each port adapter’s faceplate.
Only connect cables that comply with EIA/TIA-568 standards. (See the “Receptacles, Cables, and
Pinouts” section on page 1-4 for cable recommendations and specifications.)
Attach the network end of your RJ-45 or SC-type cable to your 10/100BASE-T transceiver, switch, hub,
repeater, DTE, or other external 10/100BASE-T equipment.
Figure 3-3
Connecting a PA-2FE-TX RJ-45 Cable—Horizontal Orientation
0
RX
1
RX
RJ-45 cable
To repeater
or DTE
1
TX
1
NK
LI
1
0
46455
PA-2FE-TX
D
LE
0
AB
0
NK
EN
LI
TX
RJ-45 cable
To repeater
or DTE
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-16
OL-3474-07
Chapter 3
Removing and Installing Port Adapters
Connecting a PA-2FE RJ-45 or SC Cable
Figure 3-4
Connecting PA-2FE-FX SC Cables—Horizontal Orientation
0
TX
0
0
RX
RX
TX
D L
1
E
LE E
S
1 TD
T
LA
C E N
C
U S
E
D S YA
0
D
O LA O
D
R K V
P IT EC
LE
1
D M
AVSE
TO
LE T
C
1 K IT S
U
S U U LA
D
S ODOD C
O
R
LA R R E
P
C P P D
RX
1
NK
LI
TX
1
RX
TX
1
1
NK
LI
46456
PA-2FE-FX
D
LE
AB
EN
Simplex (2)
To repeater
Duplex (1)
To repeater
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
3-17
Chapter 3
Removing and Installing Port Adapters
Connecting a PA-2FE RJ-45 or SC Cable
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
3-18
OL-3474-07
C H A P T E R
4
Configuring the PA-2FE
To continue your PA-2FE port adapter installation, you must configure the Fast Ethernet interfaces. The
instructions that follow apply to all supported platforms. Minor differences between the platforms—with
Cisco IOS software commands—are noted.
This chapter contains the following sections:
•
Using the EXEC Command Interpreter, page 4-1
•
Configuring the Interfaces, page 4-2
•
Checking the Configuration, page 4-9
Using the EXEC Command Interpreter
You modify the configuration of your router through the software command interpreter called the EXEC
(also called enable mode). You must enter the privileged level of the EXEC command interpreter with
the enable command before you can use the configure command to configure a new interface or change
the existing configuration of an interface. The system prompts you for a password if one has been set.
The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket (>).
At the console terminal, use the following procedure to enter the privileged level:
Step 1
At the user-level EXEC prompt, enter the enable command. The EXEC prompts you for a
privileged-level password as follows:
Router> enable
Password:
Step 2
Enter the password (the password is case sensitive). For security purposes, the password is not displayed.
When you enter the correct password, the system displays the privileged-level system prompt (#):
Router#
To configure the new interfaces, proceed to the “Configuring the Interfaces” section on page 4-2.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-1
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Configuring the Interfaces
After you verify that the new PA-2FE is installed correctly (the ENABLED LED goes on), use the
privileged-level configure command to configure the new interfaces. Have the following information
available:
•
Protocols you plan to route on each new interface
•
IP addresses, if you plan to configure the interfaces for IP routing
•
Bridging protocols you plan to use
If you installed a new PA-2FE or if you want to change the configuration of an existing interface, you
must enter configuration mode to configure the new interfaces. If you replaced a PA-2FE that was
previously configured, the system recognizes the new interfaces and brings each of them up in their
existing configurations.
You can configure each of the interfaces on a PA-2FE at:
•
100 Mbps, half duplex, for a maximum aggregate bandwidth of 200 Mbps per pair. Half-duplex
operation is the default.
•
200 Mbps, full duplex, for a maximum aggregate bandwidth of 400 Mbps per pair.
You can also configure one PA-2FE interface at 100 Mbps, half duplex, and the second PA-2FE interface
at 200 Mbps, full duplex, for a maximum aggregate bandwidth of 300 Mbps per pair.
For a summary of the configuration options available and instructions for configuring interfaces on a
PA-2FE, refer to the appropriate configuration publications listed in the “Related Documentation”
section on page viii.
You execute configuration commands from the privileged level of the EXEC command interpreter, which
usually requires password access. Contact your system administrator, if necessary, to obtain password
access. (See the “Using the EXEC Command Interpreter” section on page 4-1 for an explanation of the
privileged level of the EXEC.)
This section contains the following subsections:
•
Shutting Down an Interface, page 4-2
•
Performing a Basic Interface Configuration, page 4-7
Shutting Down an Interface
Before you remove an interface that you will not replace, or replace port adapters, use the shutdown
command to shut down (disable) the interfaces to prevent anomalies when you reinstall the new or
reconfigured port adapter. When you shut down an interface, it is designated administratively down in
the show command displays.
Follow these steps to shut down an interface:
Step 1
Enter the privileged level of the EXEC command interpreter (also called enable mode). (See the “Using
the EXEC Command Interpreter” section on page 4-1 for instructions.)
Step 2
At the privileged-level prompt, enter configuration mode and specify that the console terminal is the
source of the configuration commands, as follows:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-2
OL-3474-07
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Step 3
Shut down interfaces by entering the interface fastethernet command (followed by the interface address
of the interface), and then enter the shutdown command. Table 4-1 shows the command syntax for the
shutdown command for the supported platforms.
When you have finished, press Ctrl-Z—hold down the Control key while you press Z—or enter end or
exit to exit configuration mode and return to the EXEC command interpreter.
Table 4-1
Examples of the shutdown Command for the Supported Platforms
Platform
Command
Example
Cisco 7120 series routers
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 3.
shutdown
Cisco 7140 series routers
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
shutdown
Cisco 7200 series routers and
Cisco 7200 VXR routers
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
shutdown
Cisco uBR7200 series routers
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
shutdown
Cisco 7201 router
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
shutdown
Router(config)# interface fastethernet 3/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 3/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 4.
Router(config)# interface fastethernet 4/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 4/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 6.
Router(config)# interface fastethernet 6/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 6/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 2.
Router(config)# interface fastethernet 2/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 2/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 1.
Router(config)# interface fastethernet 1/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 1/1
Router(config-if)# shutdown
Ctrl-Z
Router#
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-3
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Table 4-1
Examples of the shutdown Command for the Supported Platforms (continued)
Platform
Command
Example
Cisco 7301 router
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 1.
shutdown
Cisco 7304 PCI port adapter
carrier card in Cisco 7304
router
interface, followed by the type
(fastethernet) and slot/port
(module-slot-number/
interface-port-number)
shutdown
Cisco 7401ASR router
interface, followed by the type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
shutdown
VIP in Cisco 7500 series
routers
interface, followed by the type
(fastethernet) and slot/port
adapter/port
(interface-processor-slot-number/
port-adapter-slot-number/
interface-port-number)
shutdown
Note
Step 4
Router(config)# interface fastethernet 1/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 1/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 0 and interface 1 of a
PA-2FE in a Cisco 7304 PCI port adapter carrier card in
module slot 3 of a Cisco 7304 router.
Router(config)# interface fastethernet 3/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 3/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 0 and interface 1 on a
PA-2FE in port adapter slot 1.
Router(config)# interface fastethernet 1/0
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 1/1
Router(config-if)# shutdown
Ctrl-Z
Router#
The example is for interface 1 and interface 0 on a
PA-2FE in port adapter slot 1 of a VIP installed
in interface processor slot 1.
Router(config)# interface fastethernet 1/1/1
Router(config-if)# shutdown
Router(config-if)# interface fastethernet 1/1/0
Router(config-if)# shutdown
Ctrl-Z
Router#
If you need to shut down additional interfaces, enter the interface fastethernet command
followed by the interface address (example: 1/1/1) of the interface. Use the no shutdown
command to enable the interface.
Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config
[OK]
Router#
The system displays an OK message when the configuration has been stored in NVRAM.
Step 5
Verify that new interfaces are now in the correct state (shut down) using the show interfaces command
(followed by the interface type and interface address of the interface) to display the specific interface.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-4
OL-3474-07
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Table 4-2 provides examples of the show interfaces fastethernet command for the supported platforms.
Table 4-2
Examples of the show interfaces fastethernet Command for the Supported Platforms
Platform
Command
Example
Cisco 7120 series routers
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 3.
Router# show interfaces fastethernet 3/0
fastethernet 3/0 is administratively down,
line protocol is down
[Additional display text omitted from this
example]
Cisco 7140 series routers
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 4.
Router# show interfaces fastethernet 4/0
fastethernet 4/0 is administratively down,
line protocol is down
[Additional display text omitted from this
example]
Cisco 7200 series routers and
Cisco 7200 VXR routers
Cisco uBR7200 series routers
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 6.
Router# show interfaces fastethernet 6/0
For Cisco 7206 router shelves:
show interfaces fastethernet
shelf-number/slot/port
(shelf-number/port-adapter-slotnumber/interface-port-number).
fastethernet 6/0 is administratively down,
line protocol is down
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 2.
[Additional display text omitted from this
example]
Router# show interfaces fastethernet 2/0
fastethernet 2/0 is administratively down,
line protocol is down
[Additional display text omitted from this
example]
Cisco 7201 router
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 1.
Router# show interfaces fastethernet 1/0
fastethernet 1/0 is administratively down,
line protocol is down
[Additional display text omitted from this
example]
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-5
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Table 4-2
Examples of the show interfaces fastethernet Command for the Supported Platforms (continued)
Platform
Command
Example
Cisco 7301 router
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 1.
Router# show interfaces fastethernet 1/0
fastethernet 1/0 is administratively down,
line protocol is down
[Additional display text omitted from this
example]
Cisco 7304 PCI port adapter carrier show interfaces fastethernet,
card in Cisco 7304 router
followed by
slot-number/port-number
(module-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in a
Cisco 7304 PCI port adapter carrier card in
module slot 3 of a Cisco 7304 router.
Router# show interfaces fastethernet 3/0
FastEthernet3/0 is down, line protocol is
down
Cisco 7401ASR router
show interfaces fastethernet,
followed by slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 1.
Router# show interfaces fastethernet 1/0
fastethernet 1/0 is administratively down,
line protocol is down
[Additional display text omitted from this
example]
VIP in Cisco 7500 series routers
show interfaces fastethernet,
followed by slot/port adapter/port
(interface-processor-slot-number/
port-adapter-slot-number/
interface-port-number)
The example is for interface 0 on a PA-2FE in port
adapter slot 1 of a VIP in interface processor
slot 1.
Router# show interfaces fastethernet 1/1/0
fastethernet 1/1/0 is administratively
down, line protocol is down
[Additional display text omitted from this
example]
Step 6
Re-enable interfaces by doing the following:
a.
Repeat Step 3 to re-enable an interface. Substitute the no shutdown command for the shutdown
command.
b.
Repeat Step 4 to write the new configuration to NVRAM. Use the
copy running-config startup-config command.
c.
Repeat Step 5 to verify that the interfaces are in the correct state. Use the show interfaces command
followed by the interface type and interface address of the interface.
For complete descriptions of software configuration commands, refer to the publications listed in the
“Related Documentation” section on page viii.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-6
OL-3474-07
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Performing a Basic Interface Configuration
Following are instructions for a basic configuration, which include enabling an interface and specifying
IP routing. You might also need to enter other configuration commands, depending on the requirements
for your system configuration and the protocols you plan to route on the interface. For complete
descriptions of configuration commands and the configuration options available for Fast Ethernet
interfaces, refer to the appropriate software documentation.
In the following procedure, press the Return key after each step unless otherwise noted. At any time you
can exit the privileged level and return to the user level by entering disable at the prompt as follows:
Router# disable
Router>
Step 1
Enter configuration mode and specify that the console terminal is the source of the configuration
commands, as follows:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#
Step 2
Specify the first interface to configure by entering the interface fastethernet subcommand, followed by
the interface address of the interface you plan to configure.
Table 4-3 gives examples of the interface fastethernet subcommand for the supported platforms.
Table 4-3
Examples of the interface fastethernet Subcommand for the Supported Platforms
Platform
Command
Example
Cisco 7120 series routers
interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in port
adapter slot 3.
interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in port
adapter slot 4.
interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in slot 4.
Cisco uBR7200 series routers interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in slot 2.
Cisco 7201 router
The example is for interface 0 of a PA-2FE in port
adapter slot 1.
Cisco 7140 series routers
Cisco 7200 series routers and
Cisco 7200 VXR routers
interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
Router(config)# interface fastethernet 3/0
Router(config-if)#
Router(config)# interface fastethernet 4/0
Router(config-if)#
Router(config)# interface fastethernet 4/0
Router(config-if)#
Router(config)# interface fastethernet 2/0
Router(config-if)#
Router(config)# interface fastethernet 1/0
Router(config-if)#
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-7
Chapter 4
Configuring the PA-2FE
Configuring the Interfaces
Table 4-3
Examples of the interface fastethernet Subcommand for the Supported Platforms (continued)
Platform
Command
Example
Cisco 7301 router
interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in port
adapter slot 1.
interface, followed by type
(fastethernet) and slot/port
(module-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in a
Cisco 7304 PCI port adapter carrier card in module
slot 3 of a Cisco 7304 router.
interface, followed by type
(fastethernet) and slot/port
(port-adapter-slot-number/
interface-port-number)
The example is for interface 0 of a PA-2FE in port
adapter slot 1.
interface, followed by type
(fastethernet) and
slot/port-adapter/port (interfaceprocessor-slot-number/port-adapterslot-number/interface-port-number).
The example is for interface 0 of a PA-2FE on a VIP
in interface processor slot 1.
Cisco 7304 PCI port adapter
carrier card in Cisco 7304
router
Cisco 7401ASR router
VIP in Cisco 7500 series
routers
Router(config)# interface fastethernet 1/0
Router(config-if)#
Router(config)# interface fastethernet 3/0
Router(config-if)#
Router(config)# interface fastethernet 1/0
Router(config-if)#
Router(config)# interface fastethernet 1/0/0
Router(config-if)#
Note
The PA-2FE is automatically configured with 100-Mbps interfaces. If Cisco IOS software detects that
the PA-2FE is connected to a 10-Mbps interface, the PA-2FE will automatically be configured to run at
10-Mbps. Use the speed [10 | 100 | auto] command to manually set the Fast Ethernet speed.
Step 3
Assign an IP address and subnet mask to the interface (if IP routing is enabled on the system) by using
the ip address subcommand, as in the following example:
Router(config-if)# ip address 10.0.0.0 10.255.255.255
Step 4
Add any additional configuration commands required to enable routing protocols and set the interface
characteristics.
Step 5
Re-enable the interfaces using the no shutdown command. (See the “Shutting Down an Interface”
section on page 4-2.)
Step 6
Configure all additional port adapter interfaces as required.
Step 7
After including all of the configuration commands to complete your configuration, press Ctrl-Z—hold
down the Control key while you press Z—or enter end or exit to exit configuration mode and return to
the EXEC command interpreter prompt.
Step 8
Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config
[OK]
Router#
This completes the procedure for creating a basic configuration. To check the interface configuration
using show commands, proceed to the following section, “Checking the Configuration.”
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-8
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Checking the Configuration
After configuring the new interface, use the show commands to display the status of the new interface
or all interfaces, and use the ping command to check connectivity. This section includes the following
subsections:
•
Using show Commands to Verify the New Interface Status, page 4-9
•
Using the ping Command to Verify Network Connectivity, page 4-21
Using show Commands to Verify the New Interface Status
Table 4-4 demonstrates how you can use the show commands to verify that new interfaces are configured
and operating correctly and that the PA-2FE appears in them correctly. Sample displays of the output of
selected show commands appear in the sections that follow. For complete command descriptions and
examples, refer to the publications listed in the “Related Documentation” section on page viii.
Note
Table 4-4
The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.
Using show Commands
Command
Function
Example
show version or
show hardware
Displays system hardware
configuration, the number of each
interface type installed, Cisco IOS
software version, names and
sources of configuration files, and
boot images
Router# show version
show controllers
Displays all the current interface
processors and their interfaces
Router# show controllers
show diag slot
Displays types of port adapters
installed in your system and
information about a specific
port adapter slot, interface
processor slot, or chassis slot
Router# show diag 2
show interfaces type 3/interface-portnumber
Displays status information about a Router# show interfaces fastethernet 3/1
specific type of interface (for
example, fastethernet) in a
Cisco 7120 series router
show interfaces type 4/interface-portnumber
Displays status information about a Router# show interfaces fastethernet 4/1
specific type of interface (for
example, fastethernet) in a
Cisco 7140 series router
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-9
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Table 4-4
Using show Commands (continued)
Command
Function
show interfaces type
slot-number/interface-port-number
Displays status information about a Router# show interfaces fastethernet 1/0
specific type of interface (for
example, fastethernet) on a
Cisco 7200 series router,
Cisco 7200 VXR router,
Cisco uBR7200 series router,
Cisco 7201 router, Cisco 7301
router, or Cisco 7401ASR router
Note
For the Cisco 7206 router
shelves, the show interfaces
command requires a shelf
number in the format show
interfaces type shelf
number/port adapter slot/port.
Example
show interfaces type
interface-processorslot-number/port-adapter-slot-number/
interface-port-number
Displays status information about a Router# show interfaces fastethernet
3/1/0
specific type of interface (for
example, fastethernet) on a VIP in a
Cisco 7500 series router
show interfaces type
module-number/interface-port-number
Displays status information about a Router# show interfaces fastethernet 3/0
specific type of interface (for
example, fastethernet) in a
Cisco 7304 PCI port adapter carrier
card in a Cisco 7304 router
show protocols
Displays protocols configured for
the entire system and for specific
interfaces
show running-config
Displays the running configuration Router# show running-config
file
show startup-config
Displays the configuration stored in Router# show startup-config
NVRAM
Router# show protocols
If an interface is shut down and you configured it as up, or if the displays indicate that the hardware is
not functioning properly, ensure that the interface is properly connected and terminated. If you still have
problems bringing up the interface, contact a service representative for assistance.
This section includes the following subsections:
•
Using the show version or show hardware Commands, page 4-11
•
Using the show diag Command, page 4-14
•
Using the show interfaces Command, page 4-18
Choose the subsection appropriate for your system. Proceed to the “Using the ping Command to Verify
Network Connectivity” section on page 4-21 when you have finished using the show commands.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-10
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Using the show version or show hardware Commands
Display the configuration of the system hardware, the number of each interface type installed, the
Cisco IOS software version, the names and sources of configuration files, and the boot images, using the
show version (or show hardware) command.
Note
The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.
The following sections provide platform-specific output examples using the show version command:
•
Cisco 7100 Series Routers—Example Output of the show version Command, page 4-11
•
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show version
Command, page 4-12
•
Cisco 7201 Router—Example Output of the show version Command, page 4-12
•
Cisco 7401ASR Router—Example Output of the show version Command, page 4-13
•
VIP in Cisco 7500 Series Routers—Example Output of the show version Command, page 4-13
Cisco 7100 Series Routers—Example Output of the show version Command
Following is an example of the show version command from a Cisco 7140 series router with a PA-2FE
installed:
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) EGR Software (C7100-JK2O3S-M)Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled 18:42
Image text-base:0x60008950, data-base:0x61CF2000
ROM:System Bootstrap, Version 12.0(5r)XE, RELEASE SOFTWARE (fc1)
BOOTFLASH:EGR Software (C7100-BOOT-M), Version 12.1(4.4)PI, MAINTENANCE INTERI
M SOFTWARE
Router uptime is 2 minutes
System returned to ROM by reload at 14:19:09 UTC Fri Jan 19 2001
System image file is "tftp://223.255.254.254//auto/tftpboot-users/image
s/c7100-jk2o3s-mz.2FE"
cisco 7140-2E3 (EGR) processor (revision A) with 122880K/73728K bytes of memory.
Processor board ID 12622543
R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
4 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 Integrated service module(s)
125K bytes of non-volatile configuration memory.
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x0
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-11
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show version Command
Following is an example of the show version command from a Cisco 7200 series router with a PA-2FE
installed:
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JS-M), Version 12.1(20000701:015939) [343]
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Sun 20-Aug-00 18:34 by pclee
Image text-base:0x60008968, data-base:0x6147A000
ROM:System Bootstrap, Version 11.1(13)CA, RELEASE SOFTWARE (fc1)
BOOTFLASH:7200 Software (C7200-BOOT-M), Version 12.0(2)XE2, RELEASE SOFTWARE (fc1)
Router uptime is 4 minutes
System returned to ROM by error - an Error Interrupt, PC 0x600BE5E0
System image file is "tftp://192.168.0.0"
cisco 7206 (NPE200) processor (revision B) with 114688K/16384K bytes of memory.
Processor board ID 15463328
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
6 slot midplane, Version 1.3
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
4 Ethernet/IEEE 802.3 interface(s)
3 FastEthernet/IEEE 802.3 interface(s)
125K bytes of non-volatile configuration memory.
4096K bytes of packet SRAM memory.
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x0
Cisco 7201 Router—Example Output of the show version Command
Following is an example of the show version command from a Cisco 7201 router:
Router# show version
Cisco IOS Software, 7200 Software (C7200P-ADVENTERPRISEK9-M), Version
12.4(biffDEV.061001), INTERIM SOFTWARE Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sun 01-Oct-06 23:42 by biff
ROM: System Bootstrap, Version 12.4(4r)XD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, 7200 Software (C7200P-KBOOT-M), Version 12.4(TAZ3DEV.060927),
INTERIM SOFTWARE
c7201alpha1 uptime is 5 days, 18 hours, 32 minutes System returned to ROM by power-on
System image file is "disk0:c7200p-adventerprisek9-mz.2006-10-01.biffdev"
This product contains cryptographic features and is subject to United States and local
country laws governing import, export, transfer and use. Delivery of Cisco cryptographic
products does not imply third-party authority to import, export, distribute or use
encryption.
Importers, exporters, distributors and users are responsible for compliance with U.S. and
local country laws. By using this product you agree to comply with applicable laws and
regulations. If you are unable to comply with U.S. and local laws, return this product
immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to export@cisco.com.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-12
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Cisco 7201 (c7201) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 2222222222222
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
1 slot midplane, Version 2.255
Last reset from power-on
1 FastEthernet interface
4 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
62443K bytes of USB Flash usbflash0 (Read/Write)
250880K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2
Cisco 7401ASR Router—Example Output of the show version Command
Following is an example of the show version command from a Cisco 7401ASR router with a PA-2FE
installed:
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) 7401ASR Software (C7401-JS-M), Version 12.1(20000701:015939) [343]
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Sun 20-Aug-00 18:34 by pclee
Image text-base:0x60008968, data-base:0x6147A000
ROM:System Bootstrap, Version 11.1(13)CA, RELEASE SOFTWARE (fc1)
BOOTFLASH:7401ASR Software (C7401ASR-BOOT-M), Version 12.0(2)XE2, RELEASE SOFTWARE (fc1)
Router uptime is 4 minutes
System returned to ROM by error - an Error Interrupt, PC 0x600BE5E0
System image file is "tftp://192.168.0.0"
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
4 Ethernet/IEEE 802.3 interface(s)
3 FastEthernet/IEEE 802.3 interface(s)
125K bytes of non-volatile configuration memory.
4096K bytes of packet SRAM memory.
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x0
VIP in Cisco 7500 Series Routers—Example Output of the show version Command
Following is an example of the show version command from a Cisco 7500 series router with a PA-2FE
installed:
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) RSP Software (RSP-JSV-M), Version 12.1(20000701:015939) [485]
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Wed 06-Sep-00 11:19 by pcl
Image text-base:0x60010970, data-base:0x616E2000
ROM:System Bootstrap, Version 11.1(8)CA1, RELEASE SOFTWARE (fc1)
BOOTFLASH:RSP Software (RSP-BOOT-M), Version 12.0(5), RELEASE SOFTWARE (fc1)
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-13
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Router uptime is 5 minutes
System returned to ROM by reload
System image file is "tftp://172.168.0.0"
cisco RSP4 (R5000) processor with 65536K/2072K bytes of memory.
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
Last reset from power-on
G.703/E1 software, Version 1.0.
G.703/JT2 software, Version 1.0.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Bridging software.
TN3270 Emulation software.
Chassis Interface.
1 EIP controller (6 Ethernet).
1 VIP2 controller (2 FastEthernet).
1 VIP2 R5K controller (2 FastEthernet).
6 Ethernet/IEEE 802.3 interface(s)
4 FastEthernet/IEEE 802.3 interface(s)
123K bytes of non-volatile configuration memory.
8192K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
20480K bytes of Flash PCMCIA card at slot 1 (Sector size 128K).
8192K bytes of Flash internal SIMM (Sector size 256K).
No slave installed in slot 7.
Configuration register is 0x100
Using the show diag Command
Display the types of port adapters installed in your system (and specific information about each) using
the show diag slot command, where slot is the port adapter slot in a Cisco 7100 series router, Cisco 7200
series router, Cisco 7200 VXR router, Cisco uBR7200 series router, Cisco 7201 router, Cisco 7301
router, or Cisco 7401ASR router, the module slot in a Cisco 7304 PCI Port Adapter Carrier Card in a
Cisco 7304 router, and the interface processor slot in a Cisco 7500 series router with a VIP.
Note
The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.
The following sections provide platform-specific output examples using the show diag command:
•
Cisco 7100 Series Routers—Example Output of the show diag Command, page 4-15
•
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show diag
Command, page 4-15
•
Cisco 7201 Router—Example Output of the show diag Command, page 4-16
•
Cisco 7401ASR Routers—Example Output of the show diag Command, page 4-17
•
VIP in Cisco 7500 Series Routers—Example Output of the show diag Command, page 4-17
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-14
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Cisco 7100 Series Routers—Example Output of the show diag Command
Following is an example of the show diag command from a Cisco 7140 series router:
Router# show diag 4
Slot 4:
Dual Port FastEthernet (MMF) Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:04:17 ago
EEPROM contents at hardware discovery:
Hardware Revision
:1.0
PCB Serial Number
:MIC05022Q6M
Part Number
:73-5420-04
Board Revision
:A0
RMA Test History
:00
RMA Number
:0-0-0-0
RMA History
:00
Deviation Number
:0-0
Product Number
:PA-2FE-FX
Top Assy. Part Number
:800-08352-04
EEPROM format version 4
EEPROM contents (hex):
0x00:04 FF 40 02 25 41 01 00 C1 8B 4D 49 43 30 35
0x10:32 32 51 36 4D 82 49 15 2C 04 42 41 30 03 00
0x20:00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41
0x30:32 46 45 2D 46 58 20 20 20 20 20 20 20 20 20
0x40:20 C0 46 03 20 00 20 A0 04 FF FF FF FF FF FF
0x50:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
30
81
2D
20
FF
FF
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show diag Command
Following is an example of the show diag command from a Cisco 7200 series router with a PA-2FE-FX
istalled in port adapter slot 2:
Router# show diag 2
Slot 2:
Dual Port FastEthernet (RJ45) Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:02:20 ago
EEPROM contents at hardware discovery:
Hardware Revision
:1.0
PCB Serial Number
:MIC04291ZUY
Part Number
:73-5419-01
Number of Slots
:1
EEPROM format version 4
EEPROM contents (hex):
0x00:04 FF 40 02 24 41
0x10:39 31 5A 55 59 82
0x20:01 01 01 01 01 01
0x30:01 01 01 01 01 01
0x40:01 01 01 01 01 01
0x50:01 01 01 01 01 01
0x60:01 01 01 01 01 01
0x70:FF FF FF FF FF FF
01
49
01
01
01
01
01
FF
00
15
01
01
01
01
01
FF
C1
2B
01
01
01
01
01
FF
8B
01
01
01
01
01
01
FF
4D
01
01
01
01
01
01
FF
49
01
01
01
01
01
01
FF
43
01
01
01
01
01
01
FF
30
01
01
01
01
01
01
FF
34
01
01
01
01
01
FF
FF
32
01
01
01
01
01
FF
FF
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-15
Chapter 4
Configuring the PA-2FE
Checking the Configuration
The following example shows information about the PA-2FE-FX installed in port adapter slot 3:
Router# show diag 3
Slot 3:
Dual Port FastEthernet (MMF) Port adapter,
Port adapter is analyzed
Port adapter insertion time 00:00:06 ago
EEPROM contents at hardware discovery:
Hardware Revision
:1.0
PCB Serial Number
:MIC04291ZX4
Part Number
:73-5419-01
EEPROM format version 4
EEPROM contents (hex):
0x00:04 FF 40 02 25 41 01 00 C1 8B 4D 49
0x10:39 31 5A 58 34 82 49 15 2B 01 FF FF
0x20:FF FF FF FF FF FF FF FF FF FF FF FF
0x30:FF FF FF FF FF FF FF FF FF FF FF FF
0x40:FF FF FF FF FF FF FF FF FF FF FF FF
0x50:FF FF FF FF FF FF FF FF FF FF FF FF
0x60:FF FF FF FF FF FF FF FF FF FF FF FF
0x70:FF FF FF FF FF FF FF FF FF FF FF FF
Note
2 ports
43
FF
FF
FF
FF
FF
FF
FF
30
FF
FF
FF
FF
FF
FF
FF
34
FF
FF
FF
FF
FF
FF
FF
32
FF
FF
FF
FF
FF
FF
FF
For complete command descriptions and examples for the Cisco 7200 series routers, refer to the
publications listed in the “Related Documentation” section on page viii.
Cisco 7201 Router—Example Output of the show diag Command
Following is an example of the show diag command from a Cisco 7201 router:
Router# show diag 1
Slot 1:
Dual OC3 POS Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:02:19 ago
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
PCB Serial Number : JAE07520DYL
Part Number : 73-8220-02
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0
Product (FRU) Number : PA-POS-2OC3
Top Assy. Part Number : 800-21857-02
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 E3 41 01 00 C1 8B 4A
0x10: 32 30 44 59 4C 82 49 20 1C 02 42
0x20: 00 00 00 00 04 00 88 00 00 00 00
0x30: 50 4F 53 2D 32 4F 43 33 20 20 20
0x40: 20 C0 46 03 20 00 55 61 02 FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF
41
41
CB
20
FF
FF
FF
FF
45
30
94
20
FF
FF
FF
FF
30
03
50
20
FF
FF
FF
FF
37
00
41
20
FF
FF
FF
FF
35
81
2D
20
FF
FF
FF
FF
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-16
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Cisco 7401ASR Routers—Example Output of the show diag Command
Following is an example of the show diag command from a Cisco 7401ASR router:
Router# show diag 1
Slot 1:
Dual Port FastEthernet (RJ45) Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:02:20 ago
EEPROM contents at hardware discovery:
Hardware Revision
:1.0
PCB Serial Number
:MIC04291ZUY
Part Number
:73-5419-01
Number of Slots
:1
EEPROM format version 4
EEPROM contents (hex):
0x00:04 FF 40 02 24 41
0x10:39 31 5A 55 59 82
0x20:01 01 01 01 01 01
0x30:01 01 01 01 01 01
0x40:01 01 01 01 01 01
0x50:01 01 01 01 01 01
0x60:01 01 01 01 01 01
0x70:FF FF FF FF FF FF
01
49
01
01
01
01
01
FF
00
15
01
01
01
01
01
FF
C1
2B
01
01
01
01
01
FF
8B
01
01
01
01
01
01
FF
4D
01
01
01
01
01
01
FF
49
01
01
01
01
01
01
FF
43
01
01
01
01
01
01
FF
30
01
01
01
01
01
01
FF
34
01
01
01
01
01
FF
FF
32
01
01
01
01
01
FF
FF
VIP in Cisco 7500 Series Routers—Example Output of the show diag Command
Following is an example of the show diag command from a Cisco 7500 series router with a PA-2FE-TX
installed in port adapter bay 0 and a PA-2FE-FX installed in port adapter bay 1 of a VIP2 installed in
interface processor slot 3:
Router# show diag 3
Slot 3:
Physical slot 3, ~physical slot 0xC, logical slot 3, CBus 0
Microcode Status 0x4
Master Enable, LED, WCS Loaded
Board is analyzed
Pending I/O Status:None
EEPROM format version 1
VIP2 R5K controller, HW rev 2.02, board revision C0
Serial number:13968891 Part number:73-2167-05
Test history:0x00
RMA number:00-00-00
Flags:cisco 7000 board; 7500 compatible
EEPROM contents (hex):
0x20:01 1E 02 02 00 D5 25 FB 49 08 77 05 00 00 00 00
0x30:60 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
Slot database information:
Flags:0x4
Insertion time:0x2750 (00:06:45 ago)
Controller Memory Size:128 MBytes DRAM, 8192 KBytes SRAM
PA Bay 0 Information:
Dual Port Fast Ethernet (RJ45), 2 ports
EEPROM format version 4
HW rev 1.00, Board revision UNKNOWN
Serial number:MIC04291ZUY Part number:73-5419-01
PA Bay 1 Information:
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-17
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Dual Port Fast Ethernet (MMF), 2 ports
EEPROM format version 4
HW rev 1.00, Board revision UNKNOWN
Serial number:MIC04291ZUY Part number:73-5419-01
Note
For complete command descriptions and examples for the VIP, refer to the publications listed in the
“Related Documentation” section on page viii.
Using the show interfaces Command
Display status information (including the physical slot and interface address) for the interfaces you
specify using the show interfaces command.
For complete descriptions of interface commands and the configuration options available for the
individual platforms, refer to the publications listed in the “Related Documentation” section on
page viii.
Note
The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.
The following sections provide platform-specific output examples using the show interfaces command:
•
Cisco 7100 Series Routers—Example Output of the show interfaces Command, page 4-18
•
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show interfaces
Command, page 4-19
•
Cisco 7201 Router—Example Output of the show interfaces Command, page 4-20
•
Cisco 7401ASR Router—Example Output of the show interfaces Command, page 4-20
•
VIP in Cisco 7500 Series Routers—Example Output of the show interfaces Command, page 4-21
Cisco 7100 Series Routers—Example Output of the show interfaces Command
Following is an example of the show interfaces command from a Cisco 7140 series router.
In this example, the two Fast Ethernet interfaces (0 and 1) are on a port adapter installed in port adapter
slot 4 of a Cisco 7140 series router; also, most of the status information for each interface is omitted.
(Interfaces are administratively shut down until you enable them.)
Router# show interfaces fastethernet 4/1
FastEthernet4/1 is up, line protocol is up
Hardware is i82543 (Livengood), address is 00b0.4a3c.e071 (bia 00b0.4a3c.e071)
Internet address is 10.0.0.1/8
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
ARP type:ARPA, ARP Timeout 04:00:00
Last input 00:00:43, output 00:00:06, output hang never
Last clearing of "show interface" counters 00:03:54
Queueing strategy:fifo
Output queue 0/40, 5 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-18
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
26 packets input, 4922 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 1 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
50 packets output, 7016 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
1 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Note
To use the show interfaces fastethernet command with the Cisco 7120 series router, replace the
interface address arguments 4/0 and 4/1, with 3/0 and 3/1, respectively.
Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Example Output of the show interfaces Command
Following is an example of the show interfaces fastethernet command from a Cisco 7200 series router
with a Fast Ethernet interface on a PA-2FE installed in slot 2:
Router# show interfaces fastethernet 2/0
FastEthernet2/0 is up, line protocol is up
Hardware is i82543 (Livengood), address is 0030.1983.b438 (bia 0030.1983.b438)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, 100BaseTX/FX
ARP type:ARPA, ARP Timeout 04:00:00
Last input 00:00:06, output 00:00:09, output hang never
Last clearing of "show interface" counters 00:01:29
Queueing strategy:fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2 packets input, 690 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
14 packets output, 2220 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
1 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Note
For the Cisco 7206 router shelves, the show interfaces command requires a shelf number in the format
show interfaces type shelf number/port adapter slot/port.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-19
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Cisco 7201 Router—Example Output of the show interfaces Command
Following is an example of the show interfaces command from a Cisco 7201 router:
Router# show interfaces
GigabitEthernet0/0 is up, line protocol is up
Hardware is MV64460 Internal MAC, address is 0019.56c5.2adb (bia
0019.56c5.2adb)
Internet address is 209.165.200.225
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 45/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:07:03, output 00:00:07, output hang never
Last clearing of "show interface" counters 00:00:04
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 180240000 bits/sec, 430965 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2222975 packets input, 133378500 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Cisco 7401ASR Router—Example Output of the show interfaces Command
Following is an example of the show interfaces fastethernet command for a Cisco 7401ASR router
with a Fast Ethernet interface on a PA-2FE installed in slot 1:
Router# show interfaces fastethernet 1/0
FastEthernet1/0 is up, line protocol is up
Hardware is i82543 (Livengood), address is 0030.1983.b438 (bia 0030.1983.b438)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, 100BaseTX/FX
ARP type:ARPA, ARP Timeout 04:00:00
Last input 00:00:06, output 00:00:09, output hang never
Last clearing of "show interface" counters 00:01:29
Queueing strategy:fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2 packets input, 690 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
14 packets output, 2220 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-20
OL-3474-07
Chapter 4
Configuring the PA-2FE
Checking the Configuration
1 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
VIP in Cisco 7500 Series Routers—Example Output of the show interfaces Command
Following is an example of the show interfaces fastethernet command from a Cisco 7500 series router
with a Fast Ethernet interface on the PA-2FE installed in slot 3:
Router# show interfaces fastethernet 3/0/0
FastEthernet3/0/0 is up, line protocol is up
Hardware is cyBus FastEthernet Interface, address is 0030.f233.a900 (bia 0030.f233.a900)
Internet address is 7.7.7.7/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, 100BaseTX/FX
ARP type:ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Queueing strategy:fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
17 packets output, 3281 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Using the ping Command to Verify Network Connectivity
Using the ping command, you can verify that an interface port is functioning properly. This section
provides a brief description of this command. Refer to the publications listed in the “Related
Documentation” section on page viii for detailed command descriptions and examples.
The ping command sends echo request packets out to a remote device at an IP address that you specify.
After sending an echo request, the system waits a specified time for the remote device to reply. Each
echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not
returned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!)
indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a
bad connection.
Following is an example of a successful ping command to a remote server with the address 10.0.0.1:
Router# ping 10.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
Router#
Router#ping 10.0.0.2
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
OL-3474-07
4-21
Chapter 4
Configuring the PA-2FE
Checking the Configuration
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
Router#
If the connection fails, verify that you have the correct IP address for the destination and that the device
is active (powered on), and repeat the ping command.
PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration
4-22
OL-3474-07